17” TFT-LCD TV MONITOR
V171HT
USER’S MANUAL
Rev. 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Features
Additional
High contrast ratio TFT LCD display supports resolution up to SXGA
Read all of these instructions and save them for later use.
1280 × 1024. @75Hz.
Follow all warnings and instructions on the product.
Product
Wall mountable with.
Built-in speakers provide sound performance.
Power management system conforms to VESA DPMS standard.
Support Plug & Play, no need for driver installation.
Advanced OSD controls for picture quality adjustment.
Detachable stand for wall-mounting with VESA 75 (mm) bracket.
Composite video and audio inputs, S-video input, TV tuner, line-out
jack for external speakers
♦ Do not cover or block the venting holes in the case.
♦ Do not insert sharp objects or spill liquid into the LCD monitor through
cabinet slots. They may cause accident fire, electric shock or failure.
♦ Disconnect the power plug from the AC outlet if you will not use it for
an extended period of time.
♦ Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
♦ Do not touch the screen directly with your fingers. You may damage the
screen, and oil from your skin is difficult to remove.
♦ Do not apply pressure to screen. The LCD is very delicate.
Power
Screen cleaning techniques
Gently clean the screen with a clean camel hair lens brush, or a soft,
clean, lint-free cloth, to remove dust and other particles that can scratch
the screen.
♦ Use the type of power indicated on label.
Plugs
Do not apply pressure to the screen surface when wiping it clean.
Do not pour or spray any liquid directly onto the screen or casing.
Chemical cleaners have been reported to damage the screen or case of
the LCD monitor.
♦ Do not remove any of the prongs of the monitor’s three-pronged power
plug.
♦ Disconnect the power plug from the AC outlet under following
conditions：
When the power cord or plug is damaged or frayed.
The product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician.
If the product exhibits a distinct change in performance, service may
be required.
Page 2
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Control Functions
a.【PC,Audio,DVI】
Control Button Front View
Power and extension cords
♦ Do not allow anything to rest on the power cord.
♦ Do not locate this product where persons will walk on the cord.
♦ Use the proper power cord with correct attachment plug type. If the
power source is 120V AC, use a power cord that has UL and C-UL
approvals. If the power source is a 240V AC supply, use the tandem (T
blade) type attachment plug with ground conductor power cord that
meets the respective European country’s safety regulations, such as VDE
for Germany.
﹝2﹞ ﹝5﹞ ﹝1﹞ ﹝3﹞ ﹝4﹞
♦ Do not over load wall outlets or power cords. Ensure that the total of all
units plugged into the wall outlet does not exceed 10 amperes.
♦ Ensure that the total ampere ratings on all units plugged into the extension
cord is not above the cord’s rating.
1. Power Switch
2. Auto adjusting
Turn on/ off the monitor.
Press this button to obtain the best display
quality and adjust the image position.
This button is used to decrease the value of
selected control option.
♦ If the power supply cord, which came with your monitor, is to be
connected to the PC instead of the wall outlet, Use an UL/TUV approved
computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A(minimum)
only.
3. Adjust (decrease －)
4. Adjust (increase ＋)
5. OSD menu / select
This button is used to increase the value of
selected control option.
Environment
Press this button to show the OSD menu on
the screen.
♦ Place the monitor on a flat and leveled surface.
♦ Place the monitor in a will-Ventilated place.
Select the OSD control options.
♦ Keep the monitor away from：
Overly hot, cold or humid places, places directly under sunlight,
dusty surroundings, equipment that generate strong magnetic fields.
♦ Please adjust the frequency to 75 Hz after setting up the LCD monitor.
♦ Then push the OSD menu button and use the Auto Adjust function to find
the best mode of your computer.
Page 4
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD Controls
Tools Menu：
Monitor Function Selection Menu：
VOLUME
Adjust the speaker volume by using ＋ and －
AUTO ADJUST Select this function to obtain the best display quality
buttons.
and adjust the image position .
MUTE
RESET
Speakers are mute.
BRIGHTNESS Adjust the brightness by using ＋ and － buttons.
CONTRAST
CLOCK
Adjust the contrast by using ＋ and － buttons.
Adjust the clock by using ＋ and － buttons.
Adjust the phase by using ＋ and － buttons.
Recall the factory settings
PHASE
H-POSITION
Press ＋ to move the image to right;
Press － to move the image to left.
Press ＋ to move the image upward ;
Press － to move the image downward.
V-POSITION
Page 7
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Temperature and RGB Adjusting Menu：
Color temperature selection --6500K, 7500K and
9300K.
COLOR
TEMP.
RED
OSD Function Selection Menu：
EXIT OSD
Exit the OSD menu.
Red pixel brightness adjustment.
OSD H.
Press ＋ to move the OSD to right ;
POSITION
OSD V.
Press － to move the OSD menu to left.
Press ＋ to move the OSD menu upward ;
Press － to move the OSD menu downward.
Green pixel brightness adjustment.
Blue pixel brightness adjustment.
GREEN
BLUE
POSITION
OSD DURATION Set the OSD display timer.
LANGUAGE Select the language for OSD.
Page 9
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
b.【AV,TV】
Control Button Front View
﹝5﹞ ﹝4﹞ ﹝1﹞ ﹝2﹞ ﹝3﹞
1. Power Switch
Power switch and remote sensor
Monitor Function Selection Menu：
2. Decrease (－)
Volume decrease, OSD menu selection downward and
channel down (－) in TV mode.
BRIGHTNESS Adjust the brightness by using ＋ and － buttons.
3. Increase (＋)
Volume increase, OSD menu selection upward and
channel up (＋) in TV mode.
CONTRAST Adjust the contrast by using ＋ and － buttons.
4. OSD menu
/ Select
Press this button to show the OSD menu on the screen .
Select the OSD control options.
SATURATION Adjust the saturation by using ＋ and － buttons.
TINT
Adjust the tint by using ＋ and － buttons.
5. Source Selection Select the input signal ( PC/ AV/ S-Video/ TV).
SHARPNESS Adjust the sharpness by using ＋ and － buttons.
Page 10
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
** TV Mode only **
TV Function Selection Menu：
CH SEARCHING TV channel auto searching
Tools Menu：
CH EDIT
Add or delete channel.
VOLUME Adjust the volume by using ＋ and － buttons.
CH FINE TUNE Tune up the signal for channel reception.
MUTE
Speakers are mute.
AIR-CABLE
CH SYSTEM
Select TV signal ,air or cable, by using ＋
and－ buttons.
RESET
INPUT
Reset function.
TV system selection.
Select input signal (PC→AV→S-Video→TV).
Page 13
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Input Diagrams
4. Installation
Electrical Connection
Inputs
Please follow the instruction below to properly connect the LCD monitor
to external electrical source.
1. Connect the female-end of the power cable to the transformer. Connect
the male-end of the power cable to the wall outlet or extension cable.
2. Connect the cable from the other end of the transformer to the LCD
monitor DC IN located at the back of the LCD monitor.
Signal Connection
【1】 【2】【3】【4】【5】 【6】 【7】
1. Power off both the LCD monitor and PC system before connecting them.
2. Take out the VGA cable from the box, then connect it to the signal
connector at the back of the LCD monitor.
1. TV TUNER IN
2. DC IN
TV Tuner or cable signal input
DC power jack.
3. Connect the other end to the VGA connector on the back of the PC
system.
3. AV IN
Composite video signal input.
S-Video signal input.
4. Please make sure the connections to both the PC system unit and the
LCD monitor are strong and secure. Please don’t forget to tighten the
screws on each connector end.
4. S-VIDEO IN
5. LINE OUT
Sound signal output (3 mm phone jack).
5. Now turn on both the PC system unit and the LCD monitor.
6. After you finish setting up the LCD monitor, please set the refresh rate to
75Hz.
6. COMPOSITE
AUDIO IN
Audio signal—right and left channel.
7. VGA input
Connect to PC VGA D-Sub signal.
7. After setting up the LCD monitor, please perform Auto Adjust in OSD so
that the LCD monitor will be automatically set to optimal color display
each time.
* Please note: When you disconnect any power cable or signal cable, please
do not pull the cable by grabbing the cable body. Please grab the cable
connector itself whenever you try to pull the cable during disconnect.
Page 15
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Modes
5. Product Specifications
Mode
Resolution
640 × 350
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
H Freq (KHz)
31.469
31.469
37.861
37.500
31.469
35.156
37.879
48.077
46.875
48.363
56.476
60.023
V Freq (Hz)
70.070
59.940
72.809
75.000
70.087
56.250
60.317
72.188
75.000
60.004
70.069
75.029
Model
1
2
V171HT
Spec
LCD Display
Pixel Pitch
17” Active matrix TFT LCD panel
0.264(H) x 0.264(V) mm
1280(H) x 1024(V), SXGA
Typical: 500 : 1 (Min: 400:1)
Typical : 300 cd/m2 (Min : 250)
Typical: 12 ms (Max: 25)
16.7 M
3
4
Max. Resolution
Contrast Ratio
Brightness
5
6
7
Response Time
Display Color
View Angle H/ V
8
9
10
11
12
Typical: 140°/ 130°
Display Mode
VGA, SVGA, XGA, SXGA
Power consumption ON<48W (maximum)
Frequency
Horizontal: 31.5-80KHz; Vertical: 56-75Hz
13
14
1280 × 1024
1280 × 1024
63.981
79.760
60.020
75.025
TV tuner
NTSC, 125 channels
Signal Connector
OSD Menu
D-sub 15, composite audio/video,
Brightness, contrast, auto adjusting, clock, phase,
volume, color temperature and language.
AC Input : 100-240V~1.8A, 50-60Hz
DC Output : 12V/ 4.2A
Power Adapter
Operating
Conditions
Storage
Temperature : 0℃~ 40℃
Humidity : 20% ~ 85%
Temperature : -20℃~ 60℃
Conditions
Certification
Set Size
Humidity : 10%~95%
BSMI,FCC (DOC), CE-B, TUV/GS, UL,CUL
413(W) x 414(H) x 195(D) mm
Weight
Net：7.5Kgs
,
Gross：9.8Kgs
Page 16
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Windows setup
6. Dead Pixel Policy
For the best display quality, please set the monitor type in
Windows.
Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra
guarantees that the monitor will be replaced if the number of dead pixels
on our monitor exceeds 5 pixels within the first year from the date of
purchase.
Control Panel > Display > Settings > Advanced > List All
Modes
7. Warranty and Customer Service
For optimal resolution, please select “1280 × 1024 @ 75Hz”
Warranty
ViewEra warrants the 15”/17” TFT-LCD monitors for one year for parts
and labor from the date of purchase. For detail information, please refer to
our website.
(http:// www.viewera.com/warranty.htm)
Customer Service
Contact your ViewEra retailer or ViewEra for after sale service. You may
contact ViewEra Customer Support:
1.
2.
3.
4.
By Mail: 328 Paseo Tesoro, Walnut, CA 91789
By Telephone: (909)595-3748
By Fax: (909)595-3526
By E-mail: [email protected]
The business hours are 9:00 am – 6:00 pm PST, Mon – Fri.
Page 19
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Remote Control Function
10. Trouble Shooting
1) Power on but no picture
→ Make sure the VGA cable is tightly connected from the video output
connector on the video card to the video input connector on the monitor.
→ Make sure you are using the standard power adapter coming with the
monitor.
1
8
7
10
9
→ Check your video card if the driver is correctly installed. If there is no
video signal from the video card, “NO INPUT SIGNAL” will show on the
screen.
5
4
6
3
2) Wrong or abnormal colors
2
→ If any color (red, green, or blue) is missing, check video cable to make
sure it is securely connected. Loose pins in the cable connector can cause a
bad connection.
3) The text and icon look blurry
→ LCD monitor has a native resolution which pixels are produced by cells
in fixed positions. When a resolution different from the native resolution is
chosen, the LCD monitor uses various interpolation methods to achieve
the pseudo resolution. To achieve the optimum viewing quality, choose the
native resolution of the panel is recommended.
NO
1
FUNCTION
NO
6
FUNCTION
OSD Menu
→ Use “Auto Tuning” function to adjust image quality on the OSD menu or
you can hold button 2 for 3 seconds to do auto tuning.
Power
4) Display position is incorrect
2
Channel Adjustment
Volume Adjustment
Mute
7
Number
Source
→ Use “Auto Tuning” function to adjust image position on the OSD menu
or you can hold button 2 for 3 seconds to do auto tuning.
3
8
4
9
Display
5) Speakers have no sound
5
OSD Adjustment
10 CATV / AIR
→ Make sure the audio cable is tightly connected from the audio output jack
on the PC to the audio input jack on the monitor.
Page 21
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
6) Residue image
The “Out of Range” may happen if you switch monitor A to monitor B for
your PC. Whenever you change the monitor for your PC, your PC may
detect it as a new hardware and automatically install a proper driver for the
monitor. So, you will have both monitor A and monitor B drivers on your
PC. Sometimes the two monitor drivers may conflict each other and cause
“Out of Range”. You can resolve “Out of Range” by uninstalling both
monitor drivers and reboot your PC. The Windows will automatically
detect the new hardware and install a proper driver for the monitor. Here is
a quick way to uninstall the monitor drivers:
→ If an image remains on the screen for an extended period of time, it may
be imprinted in the screen and leave a residue image. It is characteristic of
liquid crystal and is not malfunction or deterioration of the liquid crystal.
The residue image will disappear after a period of time. It is recommended
to set up the screen saver for your LCD monitor.
7) Out of Rang
→ The first thing you need to check is the screen resolution. Usually “Out
of Range” is caused by improper resolution setting. You can recover the
proper screen resolution as the following steps for Windows: (Assumed
that the optimal resolution and frequency setting is 1280x1024@ 60Hz.)
Boot the computer into VGA Mode (F8) [repeatedly] at startup.
Go to “Control Panel”, double click on “Display”, click on the
SETTINGS TAB, and click on the ADVANCED button.
Then Click on the Adapter TAB, click “List All Modes” and change the
screen resolution to 1280x1024. (You can select 16 bit or 32 bit color
which depends on your video card capability.)
Right click on “My Computer”, select “Properties” and click on
“Hardware”. Click on “Device Manager”, select “Monitor” and click on
“+” in front of “Monitor”. Then you can see one of the monitor drivers
called “Plug and Play Monitor”. A quick way is to uninstall all the
monitor drivers and then let Windows automatically detect the new
hardware. (Right click on the monitor driver and select “Uninstall”).
Restart your PC
Select “1280 by 1024, High Color (16 bit), Default Refresh”
Click on the “OK” and “APPLY”.
After clicking the APPLY button, a message will be displayed “Your
desktop has been reconfigured. Do you want to keep these settings?”
Click “Yes” and “OK”. Then click “OK” on the Display Properties
window.
Restart your PC
After you restart, go back to “List All Modes” to adjust your screen refresh
rate to 60 Hertz.
Page 22
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
|