The Seville
Woodburning Stove
Models 1635, 1636, 1637, 1638
Homeowner’s
Installation and
Operating
Manual
For use in the
United States and Canada
1490
SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERLY INSTALLED,
OPERATED AND MAINTAINED, A HOUSE FIRE MAY RESULT.
TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS.
FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH. CONTACT LOCAL BUILDING OFFICIALS
ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN
YOUR AREA.
Do Not Discard This Manual: Retain for Future Use
30001490 10/03 Rev. 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Specifications
Seville, Model 1635
Maximum heat output......................... 30,000 Btu’s/hr.1
Area heated...................................... Up to 1320 sq. ft.2
Fuel size/type ......................................18” (46 cm) logs
Loading ................................................................ Front
Chimney connector .................... 6” (150 mm) diameter
Chimney flue size...................... 6” (150 mm) minimum
Flue exit position ..................................................... Top
Primary air... Manually set, thermostatically maintained
Ash handling system .....................Removable ash pan
Glass panel ........................ High-temperature Infra-red
Weight ............................................................... 420lbs.
Width (Left leg - Right leg) ................... 23¹⁄₂” (59.0 cm)
Depth (Front of Ash Lip - Rear Shroud) . 28” (71.0 cm)
Height................................................... 31¹⁄₄” (79.5 cm)
with Pedestal.............................. 34³⁄₄” (88.3 cm)
1 This value can vary depending on how the stove is
operated, the type and moisture content of the fuel
used, as well as the design, construction and climatic
location of your home. Figures shown are based on
maximum fuel consumption obtained under laboratory
conditions and on average efficiencies.
2 These values are based on operation in building code-
conforming homes under typical winter climate condi-
tions in New England. If your home is of nonstandard
construction (i.e., unusually well insulated, not insu-
lated, built under ground, etc.) or if you live in a more
severe or more temperate climate, these figures may
not apply. Since so many variables affect performance,
consult your Vermont Castings authorized dealer to
determine realistic expectations for your home.
Drawings not to scale.
9¹⁄₂”
(240mm)
28”
(711mm)
Pedestal Option
34³⁄₄"
(883mm)
31¹⁄₄”
(795mm)
18¹⁄₂”
(470mm)
23¹⁄₂”
(590mm)
23¹⁄₄"
(590mm)
1490
Fig. 1 Seville 1635 dimensions.
30001490
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Installation
SAFETY NOTICE: IF YOUR STOVE IS NOT PROP-
ERLY INSTALLED, OPERATED AND MAINTAINED,
A HOUSE FIRE MAY RESULT. FOR SAFETY,
FOLLOW ALL INSTALLATION, OPERATION AND
MAINTENANCE DIRECTIONS. CONTACT LOCAL
BUILDING OFFICIALS ABOUT RESTRICTIONS AND
INSTALLATION INSPECTION REQUIREMENTS IN
YOUR AREA.
Chimneys
Your stove must be connected either to a sound
masonry chimney that meets local codes, to a relined
masonry chimney that meets local codes, or to an
approved prefabricated metal chimney. Whichever of
those types you use, the chimney and chimney con-
nector must be in good condition and kept clean.
Before you begin an installation, review your plans to
be certain that:
If you use an existing masonry chimney, it must be
inspected to ensure safe condition before the stove is
installed. Your local professional chimney sweep,
building inspector, or fire department official will be
able to make the inspection or direct you to someone
who can.
• Your stove and chimney connector will be far
enough from combustible material to meet all
clearance requirements.
• The floor protector is large enough and is
constructed properly to meet all requirements.
• You have all necessary permits from local
authorities.
The chimney should extend at least 3' (914mm) above
the highest point where it passes through a roof, and at
least 2' (610mm) higher than any portion of a building
within 10' (3m).
Your local building official is the final authority for
approving your installation as safe and determining
that it meets local and state codes.
To assure proper draft and good performance, any
chimney used with this stove should extend at least 16'
(5 m) above the flue collar of the stove.
The metal label permanently attached to the back of
the stove indicates that the Seville has been tested to
current UL and ULC standards by Intertek Testing
Services of Middleton, Wisconsin. Clearance and
installation information is also printed on the label.
Local authorities generally will accept the label as
evidence that, when the stove is installed according to
the information on the label and in this manual, the
installation meets codes and can be approved. Codes,
however, vary in different areas. Before starting the
installation, review your plans with the local building
authority. Your local dealer can provide any additional
information needed.
0 To 10’
2’ Min.
3’
0 To 10’
2’ Min.
Min.
3’
Min.
Reference Point
AC617
Fig. 2 The 2'-3'-10' Chimney Rule.
Masonry Chimneys
For any unresolved questions about installation, refer
to the National Fire Protection Association’s publication
ANSI/NFPA 211–1988 Standard for Chimneys, Fire-
places, Vents and Solid Fuel Burning Appliances. In
Canada, the equivalent publication is CSA CAN-B365,
Installation Code for Solid Fuel Burning Appliances and
Equipment. These standards are the bases for many
national codes. They are nationally recognized and
are accepted by most local authorities. Your local
dealer or your local building official may have a copy of
these regulations.
An existing masonry chimney must be inspected to
confirm that it has a lining. Do not use an unlined
chimney. The chimney also should be examined for
cracks, loose mortar, other signs of deterioration, and
blockage. Repair any defects before the chimney is
used with your stove.
A prefabricated double-
wall insulated chimney
IMPORTANT: Failure to follow these installation
instructions may result in a dangerous situation,
including a chimney or house fire. Follow all
instructions exactly and do not allow makeshift
compromises to endanger property and personal
safety.
A tile-lined
masonry
chimney
ST241
Fig. 3 Standard Chimney Types
4
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Masonry Chimneys, cont'd.
Chimney Connector Guidelines
• Unused openings in an existing masonry chimney
must be sealed with masonry to the thickness of the
chimney wall, and the chimney liner should be
repaired. Openings sealed with pie plates or
wallpaper are a hazard and should be sealed with
mortar or refractory cement. In the event of a
chimney fire, flames and smoke may be forced out
of these unused thimbles.
A chimney connector is the double-wall or single-wall
pipe that connects the stove to the chimney. The
chimney itself is a masonry or prefabricated structure
that encloses the flue. Chimney connectors are used
only to make the connection from the stove to the
chimney. They are for interior use only.
Double-wall connectors must be tested and listed for
use with solid-fuel burning appliances. Single-wall
connectors should be made of 24 gauge or heavier
steel, and should be 6" (152mm) in diameter. Do not
use galvanized chimney connector; it cannot withstand
the high temperatures that can be reached by smoke
and exhaust gases, and may release toxic fumes
under high heat.
• The chimney should be thoroughly cleaned before use.
• A newly-built masonry chimney must conform to the
standards of local building code, or, in the absence
of a local code, to a recognized national code.
Masonry chimneys must be lined, either with code-
approved masonry or precast refractory tiles,
stainless steel pipe, or a code-approved, "poured-in-
place" liner. The chimney clean-out door must seal
tightly to ensure a good draft.
If possible, do not pass the chimney connector through
a combustible wall or
ceiling. If passage
Prefabricated Chimneys
through a combustible
wall is unavoidable,
refer to the recommen-
dations in the section
following on Wall
Toward
stove
A prefabricated metal chimney must be one that is
tested and listed for use with solid-fuel burning appli-
ances to the High-Temperature (H.T.) Chimney Stan-
dard UL-103-1985 (2100° F.) for the United States, and
High Temperature (650°C) Standard ULC S-629 for
Canada.
Pass-throughs. Do not
pass the connector
through an attic, a
Flue gas
direction
Chimney Size
closet or any similar
concealed space. The
whole chimney con-
nector should be
This Seville is approved for venting into a masonry
chimney with a nominal flue size of 8" x 8" (203 x
203mm), and into a round flue size of 8" (203mm) or 6"
(152mm). It may be vented into larger chimneys as
well, however, chimneys with liners larger than 8" x
12" (203 x 305mm) may experience rapid cooling of
smoke and reduction in draft, especially if they are
located outside the home. Such large chimneys may
need to be insulated or relined for proper stove perfor-
mance.
Fig. 4 Chimney connector.
exposed and accessible for inspection and cleaning.
Install the single wall chimney connector not less than
18" (457mm) from the ceiling. Keep it as short and
direct as possible, with no more than two 90 degree
turns. If possible, use 45° elbows. Slope horizontal
runs of connectors upward 1/4" per foot (20mm per
meter) going from the stove toward the chimney. The
recommended maximum length of a horizontal run is 3’
(914mm), and the total length of chimney connector
should be no longer than 8’ (2.4m).
Do not connect this unit to a chimney flue
serving another appliance.
NOTE: Do not vent this stove into a factory-built
(zero-clearance) fireplace. This stove has not
been tested and listed for that type of installa-
tion. Factory-built fireplaces and their chim-
neys are specifically designed as a unit for use
as fireplaces. It may void the listing or be
hazardous to adapt them for any other use.
In cathedral ceiling installations, extend the prefabri-
cated chimney downward to within 8’ (2.4m) of the
stove.
SAFETY NOTE: Always wear gloves and protective
eyewear when drilling, cutting or joining chimney
connector sections .Chimney Connectors
Do not connect the stove to any air distribution
duct or system.
30001490
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Securing the Single-wall Connector to a
Prefabricated Chimney
Double-wall Chimney Connectors
The Seville is approved for installation in the U.S. and
Canada with double-wall chimney connectors that have
been tested and listed for use with solid-fuel burning
appliances by a recognized testing laboratory.
Follow the installation instructions of the chimney
manufacturer exactly.
Special adapters are available from your local dealer to
make the connection between the prefabricated
chimney and the chimney connector. The top of such
adapters attach directly to the chimney or to the
chimney’s ceiling support package. The bottom of the
adapter is secured to the chimney connector.
Follow the instructions for assembling and installing
double-wall connectors provided by the manufacturer
of the double-wall chimney. To ease assembly and
help assure safety, use chimney components manufac-
tured by a single source.
NOTE: For installations using double-wall
connectors, minimum clearances must conform to
those listed in the clearance chart on Page 12.
The adapter forms a union between the chimney and
chimney connector that ensures any soot or creosote
falling from the inner walls of the chimney will stay
inside the chimney connector.
Single-wall Chimney Connectors
Securing the Single-wall Connector to a
Masonry Chimney
• Beginning at the flue collar of the stove, assemble
the chimney connector. Insert the first crimped end
into the stove’s flue collar, and keep each crimped
end pointing toward the stove. Using the holes in
the flue collar as guides, drill 1/8" (3 mm) holes in
the bottom of the first section of chimney connector
and secure it to the flue collar with three #10 x 1/2"
sheet metal screws.
• Secure each joint between sections of chimney
connector, including telescoping joints, with at least
three sheet metal screws. The predrilled holes in
the top of each section of chimney connector serve
as guides when you drill 1/8" (3 mm) holes in the
bottom of the next section.
The Seville may be connected to either a freestanding
masonry chimney or to a fireplace masonry chimney.
Freestanding Installations
If the chimney connector must pass through a combus-
tible wall to reach the chimney, follow the recommen-
dations for Wall Pass-Through construction on Pages
7-8.
The opening through the chimney wall to the flue - the
"breech" – must be lined with a ceramic or metal thimble
which is securely cemented in place. (Fig. 5)
A metal pipe section called the “thimble sleeve,”
slightly smaller in diameter than standard connector
and the thimbles, will allow the removal of the chimney
connector system for inspection and cleaning. Thimble
sleeves are available from your local dealer.
• Secure the chimney connector to the chimney.
Instructions for various installations follow.
• Be sure the installed stove and chimney connector are
correct distances from nearby combustible material.
To install a thimble sleeve, slide it into the breech until
it is flush with the inner flue wall. Be sure that it does
not extend into the flue passage where it could inter-
fere with the draft.
NOTE: Special slip pipes and thimble sleeves that form
telescoping joints between sections of chimney con-
nector are available to simplify assembly. Slip pipes
eliminate the need to cut individual connector sections.
Consult your local dealer about these special connec-
tor sections.
The thimble sleeve should protrude 1-2" (25-51mm)
into the room. Use furnace cement and thin gasketing
to seal the sleeve in place in the thimble. Secure the
chimney connector to the outer end of the sleeve with
sheet metal screws.
Thimble Sleeve
Flue
Chimney
Connector
Keep sleeve
end flush with
flue tile
ST243
Fig. 5 The thimble, made of either ceramic or metal, must be
cemented securely in place.
6
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Connection Above the Fireplace
In this installation, the chimney connector enters the
fireplace flue though a thimble located above the
fireplace. (Fig. 6) The liner of the fireplace chimney
should extend at least to the point at which the chim-
ney connector enters the chimney. Follow all the
guidelines for installing a chimney connector into a
freestanding masonry chimney, and pay special
attention to these additional points:
• The stove and chimney connector clearances to
combustible mantel and trim materials are the same
as clearances to combustible walls. If necessary,
use a combination of mantel, trim, and connector
heat shields to provide the required clearances.
Refer to Page 12.
Chimney Connector
Heat Shield
*
Note clearance
requirement on
Pages 12-13
*
*
Mantel
• Double-check connector clearance to the ceiling.
• The fireplace damper must be closed and sealed to
prevent room air from being drawn up the flue which
could reduce performance. However, it must be
possible to reopen the damper to inspect or clean
the chimney.
ST244
• Floor protection requirements also apply to fireplace
Fig. 6 If the clearance between the chimney connector and
either the ceiling or the mantel is inadequate, a protective
heat shield is required.
installations.
Wall Pass-throughs
Whenever possible, design the installation so that the
connector does not pass through a combustible wall. If
you must include a wall pass-through in your installa-
tion, check with your building inspector before you
begin. Also check with the chimney connector manu-
facturer for any specific requirements.
Consult with your dealer regarding special connection
components available for use as wall pass-throughs.
Use only parts that have been tested and listed for use
as a wall pass-through.
Fire clay liner
Min. 2" (51mm) Chimney
clearance to brick and
combustibles
Masonry
Min. 12"
A
Chimney
constructed
to NFPA
211
(305 mm)
Chimney
connector
Fire clay
liner
A
A = Minimum 12" (305 mm) brick
construction between liner and
combustible framing materials
U.S. Requirements: The National Fire Protection
Association (NFPA) has established guidelines for use
in the United States for passing chimney connectors
through combustible walls. Many building code
inspectors follow these guidelines.
ST272
Fig. 7 Masonry Wall Pass-through with single wall
chimney connector.
Solid
insulated,
listed factory-
built chimney
length set flush
with flue
Figure 7 shows one NFPA-approved method. All
combustible material in the wall is cut away to provide
12" (305mm) clearance to the connector. Brick and
mortar are used to enclose the clearance area.
Min. 2"
(51mm)
Min. 9"
229mm
Min. 9"
(229mm)
Masonry
Chimney
constructed to
NFPA 211
Alternate methods approved by the NFPA:
Chimney
Connector
Air Space
• Using a section of double-wall chimney with a 9"
(229mm) clearance to combustibles. (Fig. 8)
24 ga.Sheet
Steel
Supports
• Placing a chimney connector pipe inside a steel
double-wall ventilated thimble, which is then sepa-
rated from combustibles by 6" (152mm) of fiber-
glass insulating material. (Fig. 9)
Non-soluble
refractory cement
Sheet Steel
Supports
ST273
Fig. 8 Wall Pass-through using factory-built insulated
chimney section.
30001490
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
• Placing a chimney connector pipe inside a section
of 9" (229mm) diameter, solid-insulated, factory-built
chimney, with two inches of air space between the
chimney section and combustibles. (Fig. 10)
Chimney clearance to sheet
steel supports and combustibles
2" (51mm) Min.
Steel Thimble
with two 1"
(25mm) Ventilated
Channels
Min. 6"
(152mm)
Canadian Requirements:In Canada, the Canadian
Standards Association has established specific
guidelines regarding wall pass-though design. Figure
11 shows one approved method in which all
Chimney Connector
Glass Fiber
Insulation
combustible material in the wall is cut away to provide
the required 18" (457mm) clearance around the
connector. The resulting space must remain empty. A
flush-mounted sheet metal cover may be used on one
side only. If covers must be used on both sides, each
cover must be mounted on noncombustible spacers at
least 1" (25mm) clear of the wall. Your local dealer or
your local building inspector can provide details of
other approved methods of passing a chimney
connector through a combustible wall.
Masonry Chimney
constructed to NFPA 211
24 ga.Sheet
Steel Supports
ST274
Fig. 9 Wall Pass-through using single wall chimney
connector with a ventilated steel thimble.
Chimney clearance to sheet steel
supports and combustibles
2" (51mm)
Min.
In Canada, this type of installation must conform to
CAN/CSA-B365, Installation Code for Solid Fuel
Burning Appliances and Equipment.
2" (51mm) Min.
air space
2" (51mm) Min.
Chimney
Connector
Prefab
Chimney
Section
Prefab
Chimney
Section
24 ga. Sheet
Steel Supports
24 ga. Sheet
Steel Supports
Masonry Chimney
constructed to NFPA 211
ST275
Fig. 10 Wall Pass-through with ventilated steel thimble.
Min. 18"
(460mm)
Chimney clearance to sheet steel
supports and combustibles
2" (51mm)
Min.
Min. 18"
(460mm)
Chimney
Connector
24 ga.Sheet
Steel Support
24 ga. Sheet
Steel Support
(one side only)
Masonry Chimney
constructed to CAN/CSA-
B365
ST276
Fig. 11 CSA approved Wall Pass-through.
8
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Keep in mind that many raised hearths will extend less
than the required clearance from the front of the heater
when it is installed. In such cases, sufficient floor
protection as described above must be added in front
of the hearth to satisfy the minimum floor protector
requirement from the front of the stove: 16" (406mm)
from the front in the United States and 18" (457mm)
from the front in Canada.
Floor Protection
A tremendous amount of heat radiates from the
bottom plate of your Madison. The floor area directly
under and around the stove will require protection from
radiant heat as well as from stray sparks or embers
that may escape the firebox.
Heat protection is provided through the use of a
Vermont Castings Bottom Heat Shield #1889. Spark
and ember protection must be provided by a floor
protector constructed with noncombustible material as
specified.
Hearth rugs do not satisfy the requirements for floor
protection as they are only fire-retardant, not fire proof.
Floor Protection Requirements
Most installations will require that the bottom heat
shield be attached. Only when the stove is placed on a
completely noncombustible surface such as unpainted
concrete over earth may it be used without the heat shield.
A
Even when the bottom heat shield is installed, you
must provide special protection to the floor beneath.
For installations with the heat shield attached, use a
noncombustible floor protector such as 1/4” non-
asbestos mineral board or equivalent, or 24 gauge
sheet metal. The floor protector may be covered with a
noncombustible decorative material if desired. Do not
obstruct the space under the heater.
A
A
D
B
C
Protection requirements vary somewhat between the
United States and Canada as follows:
For U.S. installations the floor protector is required
under the stove and must extend at least 16” from the
front of the stove (“B”, Fig. 12), and at least 6” from the
sides and rear (“A”, Fig. 12).
U. S.
Canada
A: 6"
B: 16"
C: 36”
D: 50”
8" (203mm)
18” (457mm)
40” (1016mm)
54” (1372mm)
To meet these requirements, a floor protector must be
at least 36” wide (“C”,Fig. 12) and 50” deep (“D”,Fig.
12)
ST482
Fig. 12 These dimensions are minimum requirements only.
Use greater dimensions whenever possible.
In Canada, a noncombustible floor protector is re-
quired under the heater also. The floor protector must
extend 18” (457mm) to the front (“B”, Fig. 12), and 8”
(203mm) from the sides and rear (“A”, Fig. 12).
To meet these requirements, a floor protector must be
at least 40” (1016mm) wide (“C”,Fig. 12) and 54”
(1372mm) deep (“D”, Fig. 12).
Fireplace Hearth Protection
Do not assume that your fireplace hearth is completely
noncombustible. Many fireplace hearths do not satisfy
the “completely noncombustible” requirement because
the brick or concrete in front of the fireplace opening is
supported by heavy wood framing. (Fig. 13) Because
heat is readily conducted by brick or concrete, it can
easily pass through to the wood. As a result, such
fireplace hearths can be a fire hazard and are consid-
ered a combustible floor.
Wood framing
requires protection
from radiant heat
ST247
Fig. 13 Supporting timbers under fireplace hearths are
considered to be combustible.
For all fireplace installations, follow the floor protection
guidelines described previously.
30001490
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Wall Shields
Clearance to Surrounding
Combustible Materials
Wall shields should be constructed of 24 gauge or
heavier sheet metal, or another noncombustible
material such as 1/2" (13mm) insulation board (Fig. 14)
or common brick "laid on flat," with the 3¹⁄₂" (90mm)
side down.
When the stove is operating, both the stoveplate and
the chimney connector radiate heat in all directions. A
safe installation requires that adequate clearance be
maintained between the stove and nearby combustible
materials to ensure that those materials do not
overheat.
Shields must be spaced out from the combustible
surface 1" (25mm) on noncombustible spacers. The
spacers should not be directly behind the stove or
chimney connector.
Clearance is the distance between either your stove or
chimney connector, and nearby walls, floors, the
ceiling, and any other fixed combustible surface. Keep
furnishings and other combustible materials away
from the stove as well. In general, a distance of 48"
(1220 mm) must be maintained between the stove and
moveable combustible items such as drying clothes,
furniture, newspapers, firewood, etc. Keep this area
empty of any combustible material.
Air must be able to flow between the wall and the
shield. At least 50% of the bottom 1" (25mm) of the
shield should be open and the shield must be open at
the top.
Air flow
Safe Ways To Reduce Clearances
The Seville clearance requirements, listed and
diagramed on Pages 12-13, have been established
through testing to UL and ULC standards to meet most
installation configurations. These involve four basic
variables:
Wall shield
Stud wall
framing
Noncombustible
spacers and
fasteners
Shield
• When neither the chimney connector nor the wall
has a heat shield installed.
Metal Spacer
Drywall
• When only the chimney connector has a heat
shield installed.
• When only the wall has a heat shield mounted on it.
• When a heat shield is installed on both the
chimney connector and wall.
Air flow
ST248
In general, the greatest clearance is required when the
stove will be positioned with no heat shield near a wall
with no heat shield. The least clearance is required
when both the stove and the wall have heat shields.
Reducing a stove clearance may require installation of
a listed heat shield on the chimney connector as well.
Fig. 14 Approved Wall shield construction
The following examples of wall shield construction
illustrate common designs used to safely achieve
reduced clearances to combustible wall materials.
Parallel installation, vertical chimney connector,
two wall shields. Fig. 15: Reduced clearances for
both rear and side walls. Wall shields may meet at
corner if desired. Shielding for connector is centered
behind connector.
Clearances may be reduced only by means approved
by the regulatory authority, or in accordance with the
clearances listed in this manual.
Parallel installation with rear wall pass-through,
two wall shields. Fig. 16: Reduced clearances for
both rear and side walls. Wall shields may meet at
corner if desired. Shielding for connector is centered
behind connector. Wall pass-through must comply
with codes.
Corner installation, vertical chimney connector,
two wall shields. Fig. 17: Reduced side clearances.
Wall shields MUST meet at corner.
10
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
36
(914mm)
36
(914mm)
36
(914mm)
36
(914mm)
40
40
40
40
(1016mm)
(1016mm)
(1016mm)
(1016mm)
1
1
1
1
25mm
25mm
(25mm)
(25mm)
ST483
ST485
Fig. 15 Parallel installation, vertical chimney connector, two
wall shields.
Fig. 17 Corner installation, vertical chimney connector, two
wall shields.
36
(914mm)
40
40
(1016mm)
(1016mm)
1
1
(25mm)
(25mm)
ST484
Fig. 16 Parallel installation with rear wall pass-through, two
wall shields.
30001490
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Seville 1635 Clearance Chart
Use the chart below together with the diagrams on the next page to determine the minimum clearance required for
your particular installation. In any case, it is always advisable to locate the stove as far away from walls as pos-
sible in order to take full advantage of the radiant properties of cast iron.
Stove clearances are measured between the steel rear shroud and the combustible surface.
Chimney Connector clearances are measured between the connector surface and the combustible surface. For
Douible-wall Chimney Connector, use the manufacturer’s listed clearance specification.
Use NFPA 211 default clearance or manufacturer’s installation specifications for those configurations not tested.
UNPROTECTED SURFACES
Parallel Installation
PROTECTED SURFACES
Parallel Installation
Corner
Installation
Corner
Installation
STOVE CLEARANCE
Side
Rear
Corner
Side
Rear
Corner
B 15”
C 12”
D 13”
E 8”
A 18”
F 6”
With Single-wall Connector
(381mm)
(305mm)
(330 mm)
(203mm)
(457mm)
(152mm)
J 12”
G 14”
K 6”
L 4”
With Single-wall Connector
and Connector Heat Shields
H 10”
I 6”
(305mm)
(357mm)
(152mm)
(102mm)
(254mm)
(152mm)
I 6”
Not
Tested
G 14”
H 10”
Not
Tested
Not
Tested
With Double-wall Connector
(152mm)
(357mm)
(254mm)
CHIMNEY CONNECTOR
CLEARANCE
UNPROTECTED SURFACE / Vertical
PROTECTED SURFACE / Vertical
10” (254mm)
Without Connector Heat Shields
With Connector Heat Shields
8” (203mm)
8” (203mm)
UNPROTECTED SURFACE / Horizontal
18” (457mm)
8” (203mm)
PROTECTED SURFACE / Horizontal
12” (305mm)
Single-wall Connector
ALL INSTALLATIONS
FRONT CLEARANCE
TO COMBUSTIBLES*
48" (1219mm)
* A distance of 48" must be maintained between the stove and moveable combustible items such as drying
clothes, furniture, firewood, etc.
Table 1. Approved Seville Clearances.
12
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
UNPROTECTED SURFACES
PROTECTED SURFACES
Stove Installed
Parallel to Wall
Stove Installed
Parallel to Wall
Stove in Corner
Stove in Corner
With
Single-wall
Connector
C
B
E
F
F
C
A
D
With
Single-wall
Connector
and
H
I
L
K
Connector
Heat
Shields,
or
Double-wall
Connector
I
L
G
J
ST486
Alcove Installations
D
The Seville is approved for installation into an alcove
constructed to maintain the clearances diagramed in
Figure 18.
C
E
A
B
ST487
Protected
Surfaces
Unprotected
Surfaces
(per NFPA 211)
A
56”
(1422mm)
52”
(1321mm)
Min. Width
B
34”
(864mm)
27”
(686mm)
Max. Depth
24”
(610mm)
C
36”
(914mm)
Stovetop to Ceiling
D
18”
(457mm)
12”
(305mm)
Connector to Ceiling
17”
(432mm)
10”
(254mm)
E
Connector to Wall
Fig. 18 Alcove specifications.
30001490
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Assembly
You will need the following tools to assemble the Seville:
• 7/16" open end wrench • safety glasses & gloves
Snapstat
Leads
• flat head screwdriver
• power drill w/ 1/8" (3mm) bit
Rear Shroud
• stub handle phillips screwdriver
Unpack the Stove
1. Remove the shipping straps and plastic wrap.
Snapstat
Cover
(Discard)
2. Inspect the stove and contents for shipping damage
or missing parts. Immediately notify your dealer of
any damage. Do not install this stove if any damage
is evident or any parts are missing.
Hardware Bag contents:
• Stove Legs, 4
• Fan Switch Bracket (for use with optional fan)
• 1/4-20 x 1” hex head Leg Bolts with washers, qty 4
• #10 x 1/2" sheet metal screws, qty 2
• Owner's Registration Card
ST464
Fig. 19 Install the Snapstat.
• Touch-up Paint (Porcelain enamel stoves only)
3. Remove the Top Plate from the stove body by lifting
up and away. Set it aside for replacement after the
stove has been positioned and connected to the
chimney.
Optional Fan Kit 2960
Install the Fan Kit within the Rear Shroud before you
remove the stove body from the shipping pallet.
To test the fan operation before installation:
1. Connect the power cord to a three prong outlet.
2. Turn the rheostat switch ON.
3. Apply heat to the snapstat. The fan will operate
when the snapstat reaches 90˚F.
ST462
Fig. 20 Install the Fan body into the Rear Shroud.
If the Control is left in the ON position, the fan will shut
off when the snapstat temperature falls below 90˚.
Install the Snapstat
1. Disconnect the leads from the Snapstat terminals.
2. Use pliers to remove the retainer ring from the
Snapstat Cover and slip the cover off the wire
harness. Discard cover.
Switch Bracket
3. Reconnect the wire leads to the Snapstat Plate.
4. Using two sheet metal screws from the fan kit,
attach the Snapstat Plate to the Inner Shroud as
indicated in Figure 19.
Retainer Nut
Control Knob
Switch Box
ST463
Fig. 21-1 Install the rheostat switch.
14
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Install the Fan
1. Position the Fan body within the Rear Shroud as
shown in Figure 20. The Fan’s upper flange should
be located behind the lip of the opening. Secure the
Fan to the Shroud using five sheet metal screws
and single star washer supplied with the kit.
Install the Rheostat Switch
1. Install the Switch within the Switch Bracket that is
provided with the stove in the Hardware Bag. Use
the Retainer Nut and Control Knob provided in the
Fan Kit. (Fig.21-1)
Insert Wire
Tie Plug
Here
2. Attach the Switch Bracket to the left side of the Rear
Shroud using two sheet metal screws as shown in
Figure 21-2.
ST462
Fig. 21-2 Attach the Rheostat Switch and Wire Tie.
3. Secure the fan wire harness to the back of the Shroud
using the Wire Tie plug as shown in Figure 21-2.
Install Stove Legs
Install legs before removing the stove from the pallet.
Use the four 1/4 -20x 1” hex head bolts with washers
from the parts bag. The shoulder of the legs should
seat within the locator tabs cast into the stove bottom
at each corner. Tighten the bolts with the 7/16”
wrench. CAUTION: Overtighening can strip tapped
threads.
1/4-20 X 1” Leg
Bolt and Washer
Pedestal Assembly
If you are using the Seville Pedestal option, assemble
it before removing the stove from the pallet. Follow the
assembly instructions included with the kit.
Leg Leveller
ST466
Fig. 22 Attach the Stove Legs and Leg Levellers
Remove the Stove from the Pallet
Caution. The Seville is very heavy. Do not attempt
to handle the stove without assistance.
Carefully lift the stove off of the pallet and manuever it
as close as possible to its final position.
Install the Bottom Heat Shield
The #1889 Bottom Heat Shield must be used in the
U.S. and Canada in any installation on a floor that is
not comprised of unpainted cement on earth. It is not
required for use with the Pedestal option.
1. Remove the 1/4-20x 1/2" phillips screw from the
central mounting boss in the stove bottom. (Fig. 23)
1/4-20 x 1/2” Pan Head Screw
ST465
2. Mount the bottom heat shield to the stove bottom
using the same phillips head screw previously re-
moved. The corners of the shield will butt against the
cast leg locators at each corner of the stove bottom.
Fig. 23 Attach the Bottom Heat Shield to the boss in the
center of the stove bottom.
30001490
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Install the Outside Air Adapter
Attach the Chimney Connector
The optional #1882 Outside Air Adapter provides a
collar to which a 3” (76mm) diameter air duct may be
attached directly to the air inlet area at the back of the
stove.
1. If you have not already done so, remove the Outer
Top Plate by simply lifting it off of the stove body.
2. Insert the crimped end of the first section of chimney
connector into the flue collar. Using the holes in the
collar as guides, drill 1/8" (3mm) holes through the
connector pipe. Use the three #10 x 1/2" sheet
metal screws provided to secure the chimney
connection to the flue collar.
Step 1. To accommodate the Outside Air Adapter, a
small panel must first be removed from the bottom
edge of the Rear Shroud. Use one of the following
methods, depending on the characteristics of the
shroud on your stove. (Fig. 24)
3. Replace the Outer Top.
A. Insert a flat head screwdriver into the slot in the
middle of the perforated panel at the bottom edge of
the Rear Shroud and twist to bend the section up
out of the way.
If applicable, attach Chimney Connector Heat Shields
following the instructions included with those parts.
B. Using tin snips, cut away a 4” x 1¹⁄₂” section from
the center of the lower edge of the Rear Shroud.
Step 2. Engage the Adapter against the Air Inlet of the
stove so that it rests on the lip of Back Plate as
shown in Figure 24.
Step 3. Use the two sheet metal screws provided in
the kit to attach the Adapter to the Rear Shroud at
the existing holes. (Fig. 24)
Rear Shroud
4”
2”
Primary
Air Inlet
Outside Air Adapter
ST488
Fig. 24 To allow clearance for the Outside Air Adapter,
bend or remove the Rear Shroud panel area as indicated.
16
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Operation
Air enters the stove through two, unrestricted inlets
and is heated while passing through separate channels
before being delivered through four stainless steel
How the Seville Works
Combustion control is achieved in the Seville through
two separate air delivery systems.
multi-ported tubes located at the top of the firebox.
The primary air control lever, located at the left rear
corner of the stove, controls the amount of incoming
primary air for starting, maintaining and reviving the
fire. More air entering the stove makes the fire burn
hotter and faster, while less air prolongs the burn at a
lower heat level.
Burn Only High-Quality Wood
THE SEVILLE IS DESIGNED TO BURN NATURAL
WOOD ONLY; DO NOT BURN ANY OTHER FUELS.
You will enjoy the best results when burning wood that
has been adequately air-dried. Avoid burning wood
that has not been properly seasoned. The wood
should be no longer than 18" (457mm) in length,
however, you will find that shorter wood lengths ease
refueling and promote the most efficient combustion.
For the greatest air supply and maximum heat output
(but the shortest burn time), move the lever down to
the 7 o’clock position. For a fire that will last longer
with less heat, move the lever up. You can set the
lever anywhere in between the upper and lower
extremes.
The best hardwood fuels include oak, maple, beech,
ash, and hickory that has been split, stacked, and air-
dried outside under cover for at least one year.
The Seville features an automatic thermostat to ensure
an even heat output at any manual setting you select.
As the fuel burns, the thermostat reacts to the heat
radiating form the stove surface, and, consequently
adjusts the air shutter attached to it. As the fire
intensity (and heat output) builds, the thermostat
slowly closes the air shutter, thereby restricting
incoming combustion air. As the fire intensity then
wanes (and heat output lessens), the thermostat
responds and gradually opens the air shutter which
allows more combustion air to again enliven the fire.
This ebb and flow action functions continuously to
prolong the burn cycle until the fuelbed is exhausted.
For areas that do not have a supply of hardwood,
commonly burned softwoods include tamarack, yellow
pine, white pine, Eastern red cedar, fir, and redwood.
These too should be properly dried.
Keep wood a safe distance from the heater and keep it
out of the areas around the heater used for refueling
and ash removal.
Use the Air Control Setting that
Works Best for You
No single air control setting will be appropriate for
every situation. Settings will differ depending on the
quality of the fuel, the amount of heat desired, and how
long you wish the fire to burn.
Another separate supply of oxygen is delivered to the
upper area of the firebox to support combustion of
gases released from the main fuel bed. Secondary
The control setting also depends on your particular
installation’s “draft,” or the force that moves air from
the stove up through the chimney. Draft is affected by
such things as the length, type, and location of the
chimney, local geography, nearby obstructions, and
other factors.
Do not use chemicals or fluids to start the
fire. Do not burn garbage or flammable fluids
such as gasoline, naptha, or engine oil. Also,
never use gasoline-type lantern fuel, kero-
sene, charcoal lighter fluid, or similar liquids
to start or "freshen up" a fire. Keep all such
liquids well away from the seville while it is in
use.
Too much draft may cause excessive temperatures in
the Seville, and could even damage it. On the other
hand, too little draft can cause backpuffing into the
room and/or the “plugging” of the chimney.
CAUTION: the Seville will be hot while in
operation. Keep children, clothing and
furniture away. Contact may cause skin
burns.
How do you know if your draft is excessively high or
low? Symptoms of too much draft include an
uncontrollable burn or a glowing-red stove part. A sign
of inadequate draft is smoke leaking into the room
through the stove or chimney connector joints, low
heat, and dirty glass.
DO NOT OVERFIRE THIS HEATER. Overfiring
may cause a house fire, or can result in
permanent damage to the stove. If any part of
the stove glows, you are overfiring.
30001490
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
In newer homes that are well-insulated and weather-
tight, poor draft may result from insufficient air in the
house. In such cases, a slightly opened window near
the stove on the windward side of the house will
provide the fresh air needed.
A more effective option for delivering ample
combustion air to the stove is to duct air directly from
outdoors to the stove. In fact, in some areas,
provisions for outside combustion air are required in all
new construction. The optional Seville Outside Air
Adapter is available from your dealer.
HIGH
MEDIUM
When you first begin using the stove, pay attention to
the air control settings. You will quickly find that a
specific setting will give you a fixed amount of heat. It
may take some time to determine the amount of heat
and the length of burn you should expect from various
settings.
LOW
Do not for any reason attempt to increase the firing
of your heater by altering the air control
adjustment range outlined in these directions.
Use the following air control settings as a starting point
to help determine the best settings for your installation.
(Fig. 26)
ST489a
Fig. 26 Air inlet shutter settings; High - Medium - Low.
SEVILLE CONTROL SETTINGS
Starting and Maintaining a Fire
Conditioning Your Stove
Burn Rate Primary Air Control Shutter Position
High
From 7:00
From 9:00
To 10:00
Fully Open
Half Open
Fully Closed
Medium
Low
Cast iron is extremely strong, but it can be broken with
a sharp blow from a hammer or from the thermal shock
of rapid and extreme temperature change.
Before you begin using the stove, please read the
Appendix on Draft Management, starting on page 23,
to learn how the characteristics of your particular
installation will affect your stove's performance. You
and the stove are parts of a system; other parts of the
system have a strong effect on performance. You may
need to vary your firing technique to get the results you
desire.
The cast plates expand and contract with changes in
temperature. When you first begin using your Seville,
minimize thermal stress by allowing the plates to adjust
gradually during three or four initial break-in fires
following Steps 1- 3.
BURN SOLID WOOD FUEL ONLY, AND BURN IT
DIRECTLY ON THE GRATE. DO NOT ELEVATE
THE FUEL. DO NOT BURN COAL OR OTHER
FUELS.
WARNING: OPERATE THIS STOVE ONLY WITH
THE DOOR FULLY CLOSED.
18
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
The Primary Air Inlet must be open when starting a
fire or when refueling.
Step 1. Open the primary air control fully. (Lever at
7:00)
Step 2. Place several sheets of crumpled newspaper
in the stove. Avoid using glossy or colored paper,
as these burn poorly. At the front of the firebox,
place on the paper six or eight pieces of dry kindling
split to a finger-width size, and on the kindling lay
two or three larger sticks of split dry wood approxi-
mately 1-2" (25-50mm) in diameter. (Fig. 27)
Step 3. Light the newspaper and close the door.
Gradually build up the fire by adding a few 3-5" (80-
127mm) diameter splits. (Fig. 28) If this is one of
the first few "break-in" fires, let the fire burn
brightly, and then let it die out.
ST263
Fig. 27 Start a fire with small, dry kindling.
• During the break-in fires, don't let the stove get
hotter than 500°F. (260°C) as measured on an
optional stove-top thermometer. Adjust the air
control lever as necessary to control the fire.
• Some odor from the stove’s hot metal, the paint,
and the cement is normal for the first few fires.
NOTE: Some chimneys need to be “primed,” or
warmed up, before they will draw sufficiently to
sustain a fire. To correct this situation, roll up a
couple pieces of newspaper, place them on top of
the kindling and toward the back of the stove, light
them, and close the door. This should heat the
chimney enough to initiate strong draft.
ST264
Once the draft is established, open the front door
and light the rest of the fuel bed at the bottom. Do
not light the main bed of fuel until the chimney
begins drawing.
Fig. 28 Gradually add larger pieces of wood until all the wood
is burning well.
Step 4. After the stove has been broken-in using
Steps 1-3, continue to build the fire gradually. Add
larger wood with a diameter of 3-4" (76-102mm).
Continue adding split logs of this size to the briskly-
burning fire until there is a glowing ember bed at
least 2" (51mm) deep. A good ember bed is neces-
sary for proper functioning and may take up to an
hour to establish.
Step 5. Adjust the thermostatic air control for the
desired heat output.
30001490
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Refuel While the Embers Are Still Hot
CAUTION: AVOID SLAMMING THE STOVE
DOOR OR STRIKING THE GLASS PANEL. DO
NOT OPERATE THE STOVE WITH THE GLASS
PANEL MISSING, DAMAGED, OR BROKEN. DO
NOT INSTALL SUBSTITUTE MATERIALS. SEE
MAINTENANCE SECTION FOR REPLACEMENT
INSTRUCTIONS.
Reload the Seville while it is still hot and there are
plenty of glowing embers to rekindle the fire. Include
some smaller pieces of wood in the new load of fuel to
help the stove return to its operating temperature
quickly. Wear stove gloves, and follow this procedure
when you reload your stove:
Step 1. Open the thermostat lever.
Step 2. Open the door and check the ash level in the
ash pan. If necessary, dispose of the ashes and
replace the pan.
Smoke Detectors
The use of smoke detectors throughout the home is
strongly advised, if not required by building codes or
insurance regulations. It is a good idea to install a
smoke detector in the living areas and each bedroom.
Step 3. Use a fireplace tool to break up the charcoal
and direct ash through the grate. Pull the charcoal
from the back to the front.
Step 4. Load wood — smaller, split pieces first. Close
the door. Ideal performance will be achieved by
operating with the air control set in the maximum
(HIGH) position for several minutes after refueling.
Reset the primary air control for the desired heat
output after the fire is reestablished.
You may not, however, wish to install a detector in the
immediate vicinity of the stove. Depending on the
sensitivity of the unit, the alarm can be set off while you
are tending the fire or emptying the ashes. If you install
a detector in the same room, locate it as far away from
the stove as possible.
Ash Disposal
Remove ash before it reaches the top of the ash pan.
Check the level at least once a day, and before each
refueling. Using stove gloves, pull the ash pan out of
the stove by its handle. Remove the ash pan and
properly dispose of the ashes. Be sure to keep the pan
level during disposal.
Empty the ash pan regularly, typically every one to
three days. The frequency will vary depending on how
you operate your Seville; if you burn more wood at
higher heat output settings, ash will accumulate rapidly.
Dispose of ashes into a metal container with a tight-
fitting lid kept outdoors. Put the closed container of ash
on a noncombustible floor or on the ground, well away
from all combustible materials, pending final disposal.
If the ash is disposed of by burial in soil or otherwise
locally dispersed, keep it in the closed container until
all cinders have thoroughly cooled. You can use wood
ash as a garden fertilizer.
CAUTION: Never use your household or shop
vacuum cleaner to remove ash from the stove;
always remove and dispose of the ash properly.
20
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Maintenance
Let the fire in the stove go out and allow the stove to
cool completely before beginning any maintenance
procedure.
Place the three flat gaskets (two vertical, one
horizontal) into the panel inset.
4. Install the Glass. Lay the glass on the inner gasket
with the coated side down (toward the outside of the
door). Tighten the screws snugly, but loose enough
to allow for a little movement of the glass when the
stove is in operation. Overtightening can crack the
glass immediately or cause it to crack if it is unable
to expand when hot.
Care of the Cast Iron Surface
An occasional dusting with a dry rag will keep the
painted cast iron of your Seville looking new.
The stove’s paint can be touched up as needed. First,
clean the areas to be painted with a wire brush. Then,
touch up the stove with Vermont Castings high
temperature stove paint. Apply the paint sparingly,
and keep in mind that two light coats of paint are better
than a single heavy one.
Gasket Replacement
Your Seville uses rope-type fiberglass gaskets to make
a tight seal between some parts. With use, particularly
on those parts that move, gaskets can become brittle
and compressed and can begin to lose their
Care of Porcelain Enamel Finish
effectiveness. These will need periodic replacement.
Use a dry or slightly damp rag or a soft brush to
remove spills or stains. For difficult jobs that require a
cleaning agent, use only a kitchen appliance cleaner or
polish recommended for use on enamel surfaces.
The sizes of replaceable gasket are listed below, along
with their applications.
Gasket Size
3/8” Fiberglass
...And the Parts it Seals
Door Gasket - 1203589
Cleaning the Glass
Wait until the fire is out and the stove has cooled. Be
sure to follow the standard safety procedure for
working with dusty materials: Wear safety goggles
and a dust mask.
Most of the carbon deposits on the glass will burn off
during hot fires. However, the ash residue that accu-
mulates on the glass surface should be removed
regularly to prevent etching. Follow this procedure to
clean the glass:
Step 1. Remove the existing gasket by grasping an
end and pulling firmly.
• Be sure the glass is completely cool.
Step 2. Use a wire brush or a screwdriver to clean the
channel of any remaining cement or bits of gasket.
Remove stubborn deposits of cement with a cold
chisel if necessary.
• Clean the glass with water or a cleaner made
especially for this purpose. Do not use abrasive
cleaners.
• Rinse the glass thoroughly.
• Dry the glass completely.
Step 3. Determine the correct length of the appropri-
ate-sized gasket by laying it out in the channel. Allow
an extra 1-2" (25-51mm), and mark the spot to be cut.
Glass Replacement
Step 4. Remove the gasket from the channel, place it
on a wood cutting surface, and cut it at the marked
spot with a utility knife.
Replace glass only with Vermont Castings part no.
3000-0774. The glass panel rests on a cushion
provided by three flat gaskets, and is held in place by
two clips. The glass is coated on one side which is
slightly colored. Remove the door from the stove and
place it on a sturdy, level work surface. Use a towel to
protect the porcelain enamel finish.
Twist the ends slightly to discourage the gasket from
unraveling.
Step 5. Lay an unbroken 1/8" (3mm) bead of gasket
cement in the newly-cleaned channel.
Step 6. Starting at one end, press the gasket into the
channel.
1. Remove the Door Manifold. (Two phillips head
screws).
Ensure a good joint where the gasket meets before
trimming any excess. Do not overlap the gasket ends
or leave ends with ragged edges.
2. Remove the Retainer Clips. (Two phillips head
screws on each clip).
3. Inspect the Gasket. If the window gasket is in good
condition, you can leave it in place. If you replace it,
use only Vermont Castings gaskets. Be sure the
channel around the window opening is clean, and
free of dust.
30001490
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Step 7. Press the gasketed part firmly against its
normal mating surface to seat the gasket evenly in its
channel. Close and latch the door to do this; close the
door on a piece of waxed paper to keep the cement
from migrating onto the non-gasketed part, or mask
other parts
The Chimney System
Creosote
Your Seville is designed to reduce creosote buildup
significantly. However, regular chimney inspection and
maintenance must still be performed. For safety, good
stove performance, and to protect your chimney and
chimney connector, inspect your chimney and chimney
connector on a regular schedule. Clean the system if
necessary. Failure to keep the chimney and connector
system clean can result in a serious chimney fire.
Step 8. Clean excess cement from around the chan-
nel. Let the cement that holds the new gasket dry
thoroughly.
Adjust the Door
The door latch may need adjustment as the gasket
material compresses over time. The latch engagement
may be tightened by removing the shim washers that
are under the Latch Plate. (Fig. 29) Remove only one
pair at a time. When a tight engagement can no longer
be achieved with no shim washers in place, the entire
door gasket should be replaced. Use only Vermont
Castings part no. 700-0910.
When wood is burned slowly, it produces tar,
organic vapors and moisture that combine to form
creosote. The creosote vapors condense in the
relatively cool chimney flue. As a result, creosote
residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire
within the flue system that can damage the chim-
ney and overheat adjacent combustible material.
If you do have a chimney fire, promptly:
• Close the thermostat lever.
• Get everyone out of the house.
• Call the Fire Department.
You should inspect the system every two weeks during
the heating season as part of a regular maintenance
schedule. To inspect the chimney, let the stove cool
completely. Then, using a mirror and a strong light,
sight up through the flue collar into the chimney flue. If
it is not possible to inspect the flue system in this
fashion, the stove must be disconnected to provide
better viewing access.
If a significant layer of creosote has accumulated —1/
8" (3 mm) or more — remove it to reduce the risk of a
chimney fire.
Clean the chimney using a brush the same size and
shape as the flue liner. Flexible fiberglass rods are
used to run the brush up and down the liner, causing
any deposits to fall to the bottom of the chimney where
they can be removed through the clean-out door.
The chimney connector should be cleaned by
disconnecting the sections, taking them outside, and
removing any deposits with a stiff wire brush. Reinstall
the connector sections after cleaning, being sure to
secure the individual sections with sheet metal screws.
ST268
If you cannot inspect or clean the chimney yourself,
contact your local Vermont Castings, Majestic Products
Company Authorized Dealer or hire a professional
chimney sweep.
Fig. 29 Remove shim washers to tighten latch engagement.
22
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Annual Maintenance
Draft Management
Perform a thorough cleaning, inspection and repair
each Spring, at the end of the heating season.
Your stove is only one part of a system that includes
the chimney, the operator, the fuel and the home. The
other parts of the system will affect how well the stove
works. When there is a good match between all the
parts, the stove works well.
• Thoroughly clean the chimney and chimney connec-
tor.
• Inspect the chimney for damage and deterioration.
Replace weak sections of prefabricated chimney.
Have a mason make repairs to a masonry chimney.
Wood stove operation depends on natural (unforced)
draft. Natural draft occurs when exhaust gas is hotter
(and therefore lighter) than the outdoor air at the top of
the chimney. The greater the temperature difference,
the stronger the draft. As the hot exhaust gas rises out
of the chimney it generates suction that draws air into
the stove for combustion. A slow, lazy fire with the
stove’s air inlets fully open indicates a weak draft. A
brisk fire, supported only by air entering the stove
through the normal inlets, indicates a good draft. The
inlets are passive; they regulate how much air can
enter the stove, but they do not move air into it.
• Inspect the chimney connector and replace any
damaged sections.
• Clean ash debris from under the primary air plate.
See procedure below.
• Check gasketing for wear or compression, and
replace if necessary. A 'paper test' will guide you on
this. Close and lock the door on a slip of paper and
then try to pull the paper out. If the paper pulls out
with little or no resistance, the gasket isn't snug
enough at that spot. If adjusting the latch doesn't
result in a seal that makes it hard to pull the paper
out, replace the gasketing.
The efficiency of a modern woodburning appliance, (in
which the amount of air available for combustion is
regulated), depends on the chimney to keep exhaust
gases warm all the way outdoors. The characteristics
of your chimney - whether it is steel or masonry,
interior or exterior, matched or mismatched to the stove
collar - determine how quickly it will warm up and how
well it will sustain the optimum temperatures necessary
to maintain strong draft and efficient combustion. Here
follows a description of various flue system character-
istics and related effects on stove performance.
• Check door handle for tightness. Adjust if needed.
• Check heat shield screws. Tighten as necessary.
• Clean dust from the inner sides of bottom, rear and
connector heat shields.
• Remove ashes from the ash pan and replace with
moisture absorbing material (such as cat litter) to
keep the stove interior dry. Close the stove door to
keep cats from using the litter.
Masonry Chimney
• Touch up the paint on black stoves.
Although masonry is the traditional material used for
chimney construction, it can have distinct performance
disadvantages when used to vent a controlled-combus-
tion woodstove. Masonry forms an effective ‘heat sink’
- that is, it absorbs and holds heat for long periods of
time. The large mass, however, may take a long time
to become hot enough to sustain a strong draft. The
larger the chimney (in total mass), the longer it will take
to warm up. Cold masonry will actually cool exhaust
gases enough to diminish draft strength. This problem
is compounded if the chimney is located outside the
home or if the chimney flue has a cross-sectional size
larger than the stove outlet.
Clean the Primary Air Outlet
1. Remove the phillips head screws that retain the
Primary Air Plate.
2. Use a screwdriver to pry the plate out of the ce-
mented seams.
3. Remove ash debris from the cavity.
4. Use high-temperature furnace cement to reseal the
front seam and side seams and replace the plate.
Secure with the phillips head screws.
30001490
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
Steel Chimney
Pipe & Chimney Layout
Most factory-made ‘Class A’ steel chimneys have a
layer of insulation around the inner flue. This insulation
keeps the smoke warm and protects the surrounding
structure from the high flue temperatures. Because the
insulation is less dense than masonry, the inner steel
liner warms up more quickly than a masonry chimney.
Although steel chimneys are not as attractive as their
masonry counterparts, they are very durable and
generally outperform masonry.
Every bend in the flue will act as a brake on the
exhaust as it flows from the firebox to the chimney
cap. The ideal pipe and chimney layout is straight up
from the stove through a completely straight chimney.
Use this layout if at all possible as it will promote
optimum stove performance and simplify maintenance.
If the stovepipe must elbow to enter a chimney, locate
the elbow about midway between the stove top and
the chimney thimble. This configuration lets the smoke
speed up before it must turn, keeps some pipe in the
room for heat transfer, and allows long-term flexibility
for installing a different appliance without relocating
the thimble.
Inside/Outside Location
Because the chimney’s function is to keep the smoke
warm, it is best to locate it inside the house. This
location uses the house as insulation for the flue and
allows some radiant heat release from the flue into the
home. Since an interior chimney does not continuously
lose its heat to the outdoors, it takes less heat from the
stove to get it warm and keep it warm.
There should be no more than eight feet of single-wall
stove pipe between the stove and a chimney. Longer
runs can cool the smoke enough to cause draft and
creosote problems. Use double-wall stove pipe for
longer runs.
Flue Sizing
Single Venting
The flue size for a controlled-combustion appliance
should be based on the cross-sectional volume of the
stove flue outlet. In this case, more is definitely not
better. Hot gases lose heat through expansion; if a
stove with a six-inch flue collar (28 square inch area) is
vented into a 10” x 10” flue, the gases will expand to
over three times their original volume. As gases cool
with expansion, draft strength decreases. If an over-
sized flue is also outside the house, the heat it absorbs
will be conducted to the outdoor air and the flue will
remain relatively cool.
Your stove requires a dedicated flue. Do not connect
the stove to a flue used by any other appliance.
Chimney draft is a natural form of energy and follows
the path of least resistance. If the stove is vented to a
flue that also serves an open fireplace or another
appliance, the draft will also pull air in through those
avenues. The additional air flow will lower flue tem-
peratures, reduce draft strength and promote creosote
development; overall stove performance will suffer.
The effect is similar to that of a vacuum cleaner with a
hole in the hose. In some extreme instances, the other
appliance can even impose a negative draft and result
in a dangerous draft reversal.
It is common for a masonry flue to be oversized for the
stove. Such a chimney can take quite a while to warm
up and the stove performance will likely be disappoint-
ing. The best solution to an oversize flue problem is the
installation of an insulated steel chimney liner of the
same diameter as the appliance flue outlet. The liner
keeps the exhaust gas warm and the result is a stron-
ger draft. An uninsulated liner is a second choice -
although the liner will keep the exhaust restricted to its
original volume, the air around the liner will require time
and heat energy to warm up.
Fuel
Even the best stove installation will not perform well if
poor fuel is used. If available, always use hardwood
that has been air-dried (‘seasoned’) 12-18 months.
Softwood burns more rapidly than hardwood and has a
high resin content conducive to creosote production.
Decayed wood of any type has little heat value and
should not be used.
Check your local codes. You may be required to install
a flue liner in any oversize or masonry flue.
All unseasoned (‘green’) wood has a high moisture
content. Much of its heat value will be used to evapo-
rate moisture before the wood can burn. This signifi-
cantly reduces not only the amount of energy available
to warm your home, but also the intensity of the fire
and temperature of the exhaust gas. Incomplete
combustion and cool flue temperatures promote
creosote formation and weak draft.
24
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
You can judge the moisture content of wood by its
appearance and weight or use a commercially avail-
able moisture meter for an exact measurement.
Unseasoned wood will be a third heavier than dry
wood. Also, look for cracks (‘checking’) in the ends of
the log that result from contraction as the wood dries.
The longer and wider the cracks, the dryer the wood is.
Purchase your fuel from a reputable dealer.
Negative Pressure
Good draft also depends on a sufficient supply of air to
the stove. The chimney cannot pull more air than is
available. Sluggish draft can be caused by a house
that is tight enough to prevent the ready flow of air to
the stove, or by competition between the stove and
other appliances that vent indoor air to the outside; i.e.,
exhaust fans for range hoods, clothes dryers, bath-
room, etc. If the chimney draws well when all such
equipment is turned off (or sealed, in the case of the
fireplaces and/or other stoves), you simply need to be
attentive in timing the use of the other appliances. If
you need to crack a nearby window or door to enable
the chimney to pull well, you should install an outside-
air intake to bring combustion air directly to the stove.
Consult your Vermont Castings Majestic Products
dealer regarding an adapter to attach to the stove to
connect an air duct for outdoor combustion air.
Creosote
Creosote is a by-product of low-temperature stove
operations, weak draft or both. It is a tar that results
when unburned gases condense inside the flue system
at temperatures below 290°F. Creosote is volatile and
can generate chimney fire. All of the installation
characteristics that adversely affect chimney draft also
promote creosote condensation. Consequently, you
can minimize creosote accumulation with an effective
chimney design and the use of operational techniques
that encourage good draft and complete combustion.
Conclusion
Backpuffing
Woodburning is more an art than a science. Art in-
cludes technique and since installations, homes and
fuel vary, the stove operator must also vary technique,
(mostly timing), to achieve satisfying results. Over
time, you will become familiar with the intricacies and
nuances of your particular installation and you will be
able to identify cause and effect in a variety of sea-
sonal circumstances.
Backpuffing is a condition that results when the draft is
too weak to pull flue gases out of the chimney system
as fast as the fire is generating more. Volatile gases
build up within the firebox until reaching a density and
temperature at which they ignite. With this ignition, you
may hear a muffled popping sound and see a bit of
smoke forced out of the air inlets.
This condition is most likely to occur in the spring or fall
when moderate outdoor temperatures and low intensity
fires combine to inhibit draft strength. If your stove
backpuffs, Open the air inlets to induce a livelier fire
and speed airflow through the stove. Avoid large loads
of firewood at one time. You should always see lively,
dancing flames in the firebox; a lazy, smoky fire is
inefficient and will promote draft problems.
30001490
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
3
28
41
2
43
1
3
46
40
7
39
4
10a
10
16
9a
9
24
23
34
36
38
15
5
35
17
8
36
31
29
6
32
37
22
34
30
25
33
26
26
39
12
11
21
14
44
13
18
20
18
20
19
18
20
19
19
1490
Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and
products at any time, without notice.
Seville Woodburning Stove
Item/Model Number
7. Left Side
Part Number
30000755
Item/Model Number
Part Number
30000748
7001180
1. Top
8. Secondary Air Manifold, Left
30000764
2. Rod, Gold
9. Tube A, Secondary Air
9a. Tube B, Secondary Air
30001430
30001439
3. Rod Retainer Tab, (4)
4. Inner Top
1601488
30000749
30000754
30000763
10. Tube C, Secondary Air
10a. Tube D, Secondary Air
30001440
30001441
5. Right Side
6. Secondary Air Manifold, Right
26
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
Vermont Castings Seville
0-05 Notes:
Seville 1635 (continued)
1. In this diagram and throughout this manual, 'left' and
'right' mean as you face the stove.
Item/Model Number
Part Number
11. Bottom
30001434
2. Use only Vermont Castings Glass Panel part
number 30000774 for replacement.
12. Bottom, Inner
13. Ashlip
30000759
30000758
3. Part numbers for cast iron parts in this diagram are
for 'classic' (plain black) stoves. When ordering
enamelled parts, be sure to specify color.
14. Ashpan
15. Firebrick Support
16. Back
17. Fireback Brick Ledge
18. Leg (4)
19. Leg Bolt, 1/4-20x1" hex bolt (4)
20. Heavy Leg Washer
21. Primary Air Manifold
22. Grate, Wood
30000777
30000751
30001443
30000753
30000756
1201376
30001633
30001433
30001432
30000835
30000752
30000757
1600416
4. Hardware in this stove is instandard U.S. (inch)
sizes. Most hardware items are available at local
hardware stores.
To learn the name of the dealer nearest you, call or
write:
23. Door Baffle
24. Front
25. Door
Vermont Castings, Majestic Products
410 Admiral Blvd.
Mississauga, Ontario L5T 2N6
905 670-7777
26. Door Hinge Pin, 1” (2)
27. Door Gasket, 3/8” - Low D
28. Primary Air Flap
29. Door Handle Catch
30. Wooden Handle
31. Door Handle Shaft
32. Roll Pin, 3/16” x 1”
33. Glass Gasket, horizontal
34. Glass Gasket, vertical (2)
35. Glass Panel2
1203589
30001435
30000365
30000366
30000364
1201833
30000896
30000895
30000774
30000840
30000985
30000747
1601103
36. Glass Clip (2)
37. AIr Deflector
38. Door Air Wash Manifold
39. Firebrick, (14)
40. Friction Spring
1201846
41. Thermostat Sub-Assembly
42. Ball Chain, Thermostat
43. Rear Convection Shroud Assembly
44. Bottom Heat Shield
Thermostat Cover
30001442
1201960
30001436
30000897
30001437
Hardware
#10 Flat Washer
1202423
1201374
1200811
1200830
1204214
1203210
1202473
1200983
1201326
1202058
1200993
1200986
1/4-20x3/4" Hex Screw (2)
1/4-20x1¹⁄₄" Flt Hd Phillips Screw (2)
1/4-20x1³⁄₄" Flat Hd Phillip Screw (6)
1/4-20 x 1-1/2” Stud, Full Thrd Crs (4)
1/4-20 Hex Nut, (13)
1/4 Flat Washer (8)
10-24x3/8" Round Hd Slotted Screw (4)
1/4-20x1¹⁄₂" Hex Head Screw (8)
#10 x 1/2” SMS Pan Head Screw (6)
1/4-20x3/8" Pan Hd Phillips Screw
10-24 x 5/8” Pan Hd Phillips Screw
Maintenance Kits available from your dealer:
#1884 Gasket Kit
#1877 Thermostat Kit
30001490
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
4. This warranty does not cover a stove repaired by
someone other than a Vermont Castings Majestic Products
Company Authorized Dealer.
LIMITED 3 YEAR WARRANTY
The Vermont Castings Majestic Products Company warrants
that your SEVILLE® will be free of defects in material and
workmanship for a period of three years from the date you
receive it, except that the handles, glass door panel, fireback
arch inserts, cement, and gasketing shall be warranted as
described below.
5. Damage to the unit while in transit is not covered by this
warranty but is subject to claim against the common carrier.
Contact the Authorized Dealer from whom you purchased
your Seville. (Do not operate the Seville as this may negate
the ability to process the claim with the carrier.)
The Vermont Castings Majestic Products Company will
repair or replace, at its option, any part found to be defective
when the Seville is returned with shipping charges prepaid to
an Authorized Dealer. The customer must pay for any
Authorized Dealer in-home travel fees, service charges, or
transportation costs for returning the stove to the Authorized
Dealer. It is the dealer's option whether the repair will be
done in the dealer's shop or in the customer's home. If upon
inspection, the damage is found to be the fault of the
manufacturer, repairs will be authorized at no charge to the
customer for parts and/or labor.
6. Claims are not valid where the installation does not
conform to local building and fire codes or, in their absence,
to the recommendations in the Owner's Guide.
7. The salt air environment of coastal areas, or a high
humidity environment can be corrosive to the porcelain
enamel finish. These conditions can cause rusting of the
cast iron beneath the porcelain enamel, which will cause the
porcelain enamel finish to flake off. This warranty does not
cover damage caused by a salt air or high-humidity
environment.
8. The Vermont Castings Majestic Products Company shall
have no legal obligation to enhance or update any unit once
manufactured.
Any Seville or part thereof that is repaired or replaced during
the limited warranty period will be warranted under the terms
of the limited warranty for a period not to exceed the
remaining term of the original limited warranty or six (6)
months, whichever is longer.
IN NO EVENT SHALL THE VERMONT CASTINGS
MAJESTIC PRODUCTS COMPANY BE LIABLE FOR
INCIDENTAL AND CONSEQUENTIAL DAMAGES. ALL
IMPLIED WARRANTIES INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS,
ARE LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. THIS WARRANTY SUPERSEDES ALL
OTHER ORAL OR WRITTEN WARRANTIES.
LIMITED 1 YEAR WARRANTY
The following parts of the Seville® are warranted to be free of
defects in material and workmanship for a period of one year
from the date you receive it. These parts are the handles,
glass door panel, all firebricks, cement and gasketing. Any
of these items found to be defective will be repaired or
replaced at no charge, upon the return of said part to an
Authorized Dealer with postage prepaid.
Some states do not allow the exclusion or limitations of
incidental and consequential damages or limitations on how
long an implied warranty lasts, so the above limitations may
not apply to you. This warranty gives you specific rights and
you may have other rights which vary from state to state.
EXCLUSIONS & LIMITATIONS
1. This warranty is transferable; however, proof of original
retail purchase is required.
HOW TO OBTAIN SERVICE
If a defect is noted within the warranty period, the customer
should contact a Vermont Castings Majestic Products
Company Authorized Dealer with the following information:
2. This warranty does not cover misuse of the stove. Misuse
includes overfiring which will result if the stove is used in
such a manner as to cause one or more of the stove plates
to glow red. Overfiring can later be identified by warped
plates and areas where the paint pigment has burned off.
Overfiring in enamel stoves is identified by bubbling,
cracking, chipping and discoloration of the porcelain enamel
finish.
1. Name, address, and telephone number of the purchaser.
2. Date of purchase.
3. Serial number from the label on the back of the stove.
4. Nature of the defect or damage.
5. Any relevant information or circumstances, i.e.,
installation, mode of operation when defect was noted.
The Vermont Castings Majestic Products Company offers no
warranty on chipping of enamel surfaces. Inspect your stove
for any damage to the enamel prior to accepting it.
A warranty claim will then start in process. The Vermont
Castings Majestic Products Company reserves the right to
withhold final approval of a warranty claim pending a visual
inspection of the defect by authorized representatives.
3. This warranty does not cover misuse of the SEVILLE as
described in the Owner's Guide, nor does it cover a
SEVILLE which has been modified unless authorized by a
Vermont Castings Majestic Products Company
representative in writing. This warranty does not cover
damage caused by burning treated wood, saltwater
driftwood, or any fuel not recommended in the Owner's
Guide.
Vermont Castings, Majestic Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
©Vermont Castings, Majestic Products
28
30001490
Download from Www.Somanuals.com. All Manuals Search And Download.
|