UBC780XLT
TRUNK TRACKER III
Download from Www.Somanuals.com. All Manuals Search And Download.
Front View and Display
3
4
5
6
7
8
1
2
U
SVC
9
10
11 121314 15 16 17
25 26 27 28
21
22
23
24
29
30
31
18
19
20
32
17. Enter/Remote Key (E/REM)
18. Trunk Mode Indicator
1. VFO/SELECT Control
2. VOLUME/SQUELCH Control
3. Scan Key (SCAN)
4. Manual Key (MAN)
5. Display
19. Trunk Type Indicators
20. Frequency Display
21. Priority Channel Indicator
22. Channel Number Display
23. Bank/Trunk Scan List Indicator
24. Scanner/Channel Mode Indicators
25. Receiving Mode Indicators
26. Frequency/Channel Indicators
27. CTCSS/DCS Indicators
28. ID/Code/Frequency Display
29. Trunk Repeater Activity Indicators
30. Enter Lock Indicator
6. Search Key (SRCH)
7. Hold/Up Key (HOLD/L)
8. Numeric Keypad (each banks
channel numbers)
9. Menu Key (MENU)
10. Trunk Key (TRUNK)
11. Limit/Down Key (LIMIT/L)
12. Select/Mute Key (SELECT/MUTE)
13. Decimal/Reverse Key (
14. Lockout Key (L/O)
15. Priority Key (PRI)
/RVRS)
31. Signal Meter
32. Character Display
16. Service Key (SVC)
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear View
33
34
35 36
37
34. Tape Recorder Output Jack
35. External Speaker Jack
36. DC Power Jack
33. Antenna Connector
37. Remote Control Terminal
Uniden® and Bearcat® are registered trademarks of Uniden Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts
NOTE: SMART SCAN NOT
APPLICABLE IN
AUSTRALIA
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .inside front cover
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
What is Scanning? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
What is Searching? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
What is Trunk Tracking? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Included with Your Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting an Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Mounting an Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Optional Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Typical Mounting Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Mounting the Scanner in Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Applying Power for Vehicle Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Applying Power Using Standard AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting an External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting an Earphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Listening Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting the Clone Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting the Tape Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Turn the Scanner On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setting the Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Understanding the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Storing Frequencies into Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Duplicate Frequency Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Storing Text Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Beep Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Programming Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Deleting a Stored Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
RF Attenuation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Setting the Delay Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Channel Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Restoring a Locked-out Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Restoring All Locked-out Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..24
Priority Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Changing the Priority Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Searching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Setting a Search Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Search Hold Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Data Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Frequency Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Storing Search Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Auto Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Squelch (SQ) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Additional Menu Options for Searching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Service Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Service Search Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Trunked Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Programming and Receiving Trunked Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Programming Trunking Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Download from Www.Somanuals.com. All Manuals Search And Download.
i
Selecting Trunking Programming Menu Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Selecting Trunking System Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Setting the Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Receiving Trunked Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Trunked Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
ID Hold and Direct Entry ID Hold Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ID Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Restoring Locked-out IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Channel Activity Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Scan Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Programming ID Scan Lists Manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
ID Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Setting Priority in Trunking Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Programming Scan Lists During Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Deleting a Stored ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Moving between Scan List Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
I-Call (Motorola/EDACS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Multi-Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
EDACS Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
EDACS Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Programming System Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
An EDACS trunked System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Special EDACS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
LTR Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
LTR Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Motorola Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Motorola Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Fleet Map Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Selecting a Preset Fleet Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Programming a Fleet Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Programming a Hybrid System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Setting the Base, Spacing Frequencies and Offset Channel for Motorola VHF/UHF Trunked Systems .51
Toggling the Status Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Control Channel Only Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Disconnect Tone Detect Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Remote Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Remote (PC Control) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Clone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
One Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .inside back cover
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Terminology
What is Scanning?
Unlike standard AM or FM radio stations, most two-way communications do not transmit
continuously. The UBC780XLT scans the channels you program until it finds an active
frequency.
Scanning stops on an active frequency and remains on that channel as long as the
transmission continues. When the transmission ends, the scanning cycle resumes until
another transmission is received.
What is Searching?
The UBC780XLT can search each of its 24 bands to find active frequencies. This is different
from scanning because you are searching for frequencies that have not been programmed
into your scanner. The scanner automatically chooses between two speeds while searching.
Turbo Search, can search the VHF FM bands at up to 300 channels per second.
What is Trunk Tracking?
Conventional scanning is a simple concept. You enter a radio frequency in your scanner’s
memory which is used by someone you want to monitor. For example, the police in your
area may broadcast on 460.500 MHz, the fire department on 154.445 MHz, the highway
department on 37.900 MHz, etc. So when your scanner stops on a frequency, you usually
know who it is, and more importantly, you can stop on a channel and listen to an entire
conversation. This type of scanning is easy and fun.
As the demand for public communications has increased, many public radio users don't
have enough frequencies to meet their needs, and this has created a serious problem.
Trunking radio systems solve this problem.
In a trunked radio system, which contains up to 28 different frequencies, radio users are
divided into groups, often called talkgroups, and these talkgroups are assigned specific IDs.
When someone in a talkgroup uses their radio, a brief burst of data is broadcasted before
each transmission. The trunking system computer uses this data to temporarily assign each
radio in a talkgroup to an available frequency. If the group using a frequency stops
broadcasting or pauses between replies for a few seconds, they are removed from the
frequency so another talkgroup can use it.
Sharing of the available public service frequencies, or trunking, allows cities, counties, or
other agencies to accommodate hundreds of users with relatively few frequencies.
Following a conversation on a trunked system using a scanner is difficult, if not impossible.
Because when there's a short break during the conversation you're monitoring, it’s possible
that the talkgroup will be assigned to a completely different frequency in the trunked
system. This type of scanning is difficult and frustrating.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
TrunkTrack™ changes this! Not only does your new UBC780XLT scan channels like a
conventional scanner, it actually follows the users of a trunked radio system. Once you know
a talkgroups ID, you won’t miss any of the action.
If you're a new scanner enthusiast, you may want to read the first part of this manual and
use your scanner in conventional mode before you begin trunk tracking. Understanding
scanning fundamentals and its terminology will make trunk tracking much easier. A glossary
of other commonly used terms is provided in the back. (Refer to the “Glossary of Terms”
section.) But if you're already an experienced scanner operator, you may want to skip to
Trunked System on page 32.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Feature Highlights
• Trunk Tracking – Follows VHF High Band, UHF, 800MHz trunked public and government
service systems just as if conventional two-way communications were used.
• Multi-Track – Track more than one trunking system at a time. Scan conventional and
trunked systems at the same time.
• 500 Channels – Program one frequency into each channel. You must have at least one
channel programmed to use the Scan mode.
• 24 Bands, 10 Banks – Includes 24 bands, with Aircraft and 800 MHz.10 banks with 50
channels each are useful for storing similar frequencies to maintain faster scanning cycles
or for storing all the frequencies of a trunked system.
• 25 MHz-1300 MHz – Indicates the range of frequencies that can be searched within the
bands of your scanner.
Note: The frequency coverage is not continuous and excludes the 512-806MHz band.
• 10 Priority Channels – You can assign one priority channel in each bank. Assigning a
priority channel allows you to keep track of activity on your most important channel(s)
while monitoring other channels for transmissions. You can also assign trunking priority
talkgroups.
• Preprogrammed Service (SVC) Search – Allows you to toggle through preprogrammed
Police, UHF CB, railroad, aircraft, and marine frequencies.
• Unique Data Skip – Allows your scanner to skip unwanted data transmissions and
reduces birdies.
• Memory Backup – If the battery completely discharges or if power is disconnected, the
frequencies programmed in your scanner are retained in memory.
• Manual Channel Access – Go directly to any channel.
• Attenuator – Reduces the signal strength on a per frequency basis.
• Turbo Search – Increases the search speed to 300 steps per second. This applies only to
transmission bands with 5 kHz steps.
• Text Tags – You can customise your scanner by storing text tags (up to 16 characters).
• Auto Store – The scanner automatically arranges a memory store for searched frequencies.
• CTCSS/DCS – The scanner can receive and search for subaudible tones.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Included with Your Scanner Package
If any of these items are missing or damaged, immediately contact your place of purchase.
• AC Adaptor
• Cigarette Lighter
Adaptor Cord
• DC Cord
• Mounting Bracket
• Telescopic Antenna
• Operating Guide
• Other Printed Materials
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Setup
Connecting an Antenna
You must install an antenna before you can operate the scanner. You have been provided a
standard telescopic antenna that works well with this scanner, but you may want to
purchases another type to increase the range. To connect the telescopic antenna, simply
connect it to the BNC type ANT. connector on the rear of the scanner. You can purchase a
variety of scanner antennas for both mobile and base station available at a local electronics
store. Choose the one that best meets your needs.
When deciding on a mobile or base station antenna and its location, consider these points.
• The antenna should be as high as possible on a vehicle or a house.
• The antenna and its cable should be as far as possible from sources of electrical noise
(ignition systems, gauges, and so on).
• The antenna should be vertical for the best performance.
Mounting an Antenna
Once you choose an antenna, follow the mounting instructions supplied with the antenna.
Then route the antenna cable to the scanner.
The antenna connector on your scanner makes it easy to use the scanner with a variety of
antennas, such as an external mobile antenna or an outdoor base station antenna.
Always use 50 ohm coaxial cable, such as RG-58 or RG-8, to connect an outdoor antenna.
For lengths over 50 feet, use RG-8 low-loss dielectric coaxial cable. If your antenna’s cable
does not have a BNC connector, you will also need a BNC adaptor (available at a local
electronics store).
Follow the Installation instructions supplied with the antenna, route the antenna cable to the
scanner, then connect it to the ANT. jack.
Warning: Use extreme caution when you install or remove an outdoor antenna. If the
antenna starts to fall, let it go! It could contact overhead power lines. If the
antenna touches a power line, contact with the antenna, mast, cable, or guy
wires can cause electrocution and death. Call the power company to remove
the antenna. DO NOT attempt to do it yourself.
Optional Antenna
If you have chosen an optional mobile antenna, connect the antenna plug into the ANT
connector on the rear of the scanner. (For more information on antenna installation, please
refer to the instruction guide that came with your antenna.)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Typical Mounting Methods
The UBC780XLT can be conveniently mounted on a table, bulkhead, overhead, or any other
desired location (refer to figure below for typical mounting methods).
Caution: Make sure there are no hidden electrical wires or other items behind the desired
location before proceeding. Check that free access for mounting and cabling
is available.
• Table top mount
• Bulkhead mount
• Overhead mount
Mounting the Scanner in Your Vehicle
Before you mount the scanner, make sure you have all the necessary materials. Then
confirm that the scanner fits your vehicle’s mounting area. This unit requires a mounting
area of 61mm high by 176.5mm wide by 167mm deep.
Caution: Be sure to avoid obstructions behind the mounting surface.
Follow these steps to mount the scanner in your vehicle.
1. Choose a mounting location, then use the supplied
mounting bracket as a template to mark the positions for
the mounting screw holes.
2. In the marked positions, drill holes slightly smaller than
the supplied screws.
3. Attach the mounting bracket to the mounting location
using the supplied screws and lock washers.
4. Attach the scanner to the mounting bracket using the
supplied mounting knobs.
5. Connect the antenna’s cable to the ANT. connector on the
back of the scanner.
Note: If the antenna cable’s connector does not fit in the ANT.
connector, you might also need a Motorola-to-BNC
antenna plug adaptor (available at a local
electronics store).
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Applying Power for Vehicle Installation
You can power your scanner using either the supplied DC power cord or your vehicle’s
cigarette lighter socket using DC cigarette lighter power cord.
Caution: You must use a power source that supplies 13.8 V DC and delivers at least
700 mA. Your standard 12V car battery should be sufficient. The cord connector’s
centre tip must be set to positive and its plug must fit the scanner’s DC 13.8 V
jack. The supplied DC power cord meets these specifications. Using a power cord
that does not meet these specifications could damage the scanner or the adaptor.
• Always connect the adaptor or DC power cord to the scanner before you connect it to the
power source. When you finish, disconnect the adaptor or DC power cord from the power
source before you disconnect it from the scanner.
• For added safety and to protect your scanner,
disconnect the cable from your vehicle battery’s
negative (-) terminal before you begin.
Follow these steps to connect the supplied DC power cord.
1. Connect the power cord’s black wire to a chassis ground, such as a metal screw
attached to a metal part of the vehicle’s frame. Be sure that the screw is not insulated
from the frame by a plastic part.
2. Connect the power cord’s red wire (with in-line fuse)
to a source of voltage that turns on and off with the
ignition switch, such as a spare accessory terminal in
your vehicle’s fuse box.
3. Insert the power cord’s barrel plug into the DC 13.8 V
jack on the back of the scanner.
4. Reconnect the cable to the vehicle battery’s
negative (-) terminal.
To power the scanner from a vehicle’s 12 V power source
(such as a cigarette-lighter socket), use the supplied cigarette-lighter adaptor cord.
To connect the supplied DC cigarette-lighter power cord, insert its barrel plug into the
DC 13.8 V jack on the back of the scanner, then plug the power cord into your vehicle’s
cigarette lighter socket.
Note: If you use a cigarette-lighter power cord and your vehicle’s engine is running, you
might hear electrical noise from the engine while scanning. This is normal.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Desktop Installation
You can place this scanner on a desk, shelf, or
table to use it as a base station.
1. Flip up the feet for desk installation.
2. Extend the antenna to full vertical position. Adjust
the angle for best reception.
Applying Power Using Standard AC Power
To power the scanner from an AC outlet, use the provided AC adaptor with a 5.5 mm outer
diameter/2.1mm inner diameter tip.
Caution: You must use only the AC adaptor provided as power source that supplies
13.8 V DC and delivers at least 700 mA. The cord connector’s centre tip must be
set to positive and its plug must fit the scanner’s DC 13.8 V jack. Using an
adaptor that does not meet these specifications could damage the scanner or the
adaptor.
• Always connect the AC adaptor to the scanner before you connect it to AC power.
When you finish, disconnect the adaptor from the AC power before you disconnect it from
the scanner.
1. Insert the adaptor’s barrel plug into the DC
13.8 V jack on the back of the scanner.
13.8V
2. Plug the adaptor into a standard AC outlet.
Note: Use only the AC adaptor supplied with
your scanner.
Connecting an External Speaker
In a noisy area, an external speaker (available at a local electronics store) positioned in the
right place might provide more comfortable
listening.
Plug the speaker cable’s 1/8 inch (3.5 mm)
plug into your scanner’s EXT. SP. jack.
Note: Connecting an external speaker
disconnects the scanner’s
internal speaker.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Connecting an Earphone
For private listening, you can connect an earphone (not supplied) with a 3.5 mm plug to the
EXT. SP. jack on the back of the scanner. Be very careful as damage to your hearing can
result if the VOLUME control is not set to the lowest level first. See below for “Listening
Safely” instructions. (Your local electronics store should carry a wide selection of
earphones.) Once the earphone is connected, it will automatically disconnects the internal
speaker.
Listening Safely
To protect your hearing, follow these guidelines when you use an earphone or headphones.
• Do not listen at extremely high volume levels. Extended high volume listening can lead to
permanent hearing loss.
• Set the VOLUME to the lowest setting before you begin listening. After you begin listening,
adjust the VOLUME to a comfortable level.
• Once you set the VOLUME, do not increase it. Over time, your ears adapt to the volume
level, so a volume level that does not cause discomfort might still damage your hearing.
Connecting the Clone Cable
You can transfer the programmed data to and from another UBC780XLT scanner using an
RS232C Cable (9 pin to 9 pin) (not supplied). Connect the cable between each scanner’s
REMOTE jacks. See “Clone Mode” on page 56. You can also upload or download the
programmed data to or from a PC using an optional PC interface kit available through your
local electronics store.
Connecting the Tape Recorder
You can use a standard tape recorder or a VOX (Voice Operated Control) recorder.
To connect the recorder to the scanner, connect a cable with a 1/8 inch (3.5 mm) plug from
the tape recorder’s remote jack to the TAPE OUT jack on the back of the scanner. (Your
local electronics store should carry a wide selection of cables and tape recorders.) Refer to
the “Record” section under “Additional Features” in the manual.
Remember!
• You must mark a channel, ID, talkgroup, or bank for Recording in order for this
feature to work. The LINE icon appears on all channels that have been properly marked.
• This feature does not work if your scanner is set with MUTE ON.
• The VOLUME control affects the Audio output. Do not set the volume on
minimum. Make a trial taping to be certain the volume levels are set correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Basic Operation
Turn the Scanner On
Turn the VOLUME control clockwise out of the detent position. The scanner automatically
starts scanning. Since there are no frequencies programmed in your scanner initially, you
may not receive any signals. Once you set the squelch and program some frequencies, you
will be hearing conversations regularly.
Setting the Squelch
To set the squelch, you must be in the Manual mode, and you
should not be receiving a signal on your scanner.
1. Press MAN until you do not hear a signal.
2. Make sure that the VOLUME is set to a
comfortable listening level.
STRONG SIGNALS
MEDIUM SIGNALS
3. Think of the Squelch Control as a gate. Turn
WEAK SIGNALS
SQUELCH fully counter-clockwise. This raises
the “Squelch Gate” so high that only very
NOISE
strong signals can get through.
STRONG SIGNALS
MEDIUM SIGNALS
4. Turn SQUELCH fully clockwise until you hear
WEAK SIGNALS
a hiss. This lowers the “Squelch Gate” so that
everything gets through – noise, weak signals,
NOISE
and strong signals.
STRONG SIGNALS
MEDIUM SIGNALS
WEAK SIGNALS
5. Turn SQUELCH back counter-clockwise just
until the hiss stops. Now the “Squelch Gate”
allows only clear signals through.
NOISE
Next you must program some frequencies. (Page 18) It is recommended that you read the
next part “Understanding the Menu System” because it will assist you in accessing and
understanding many of the features. Later in a section called “Additional Features”, you will
find explanations on how to disable the keypad acknowledgement tones, how to mute the
audio, how to change the appearance of the display and other general features.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Understanding the Menu System
It is very important for you to understand the Menu screen. To navigate through the Menu
screen is really quite simple. Many of the features of this scanner, can only be accessed by
the menu screens. There are several ways to get through the screens. First of all, press
MENU to get started. Any time you want to exit this mode or simply quit from where you are,
repeatedly press MENU until the scanner returns to the original state. Anytime you are in the
Menu Mode, the audio will be muted.
To assist you in understanding the Menu screen, flow charts are provided towards the back
of the manual so you can follow along. Two things to remember are scroll through the menu
and execute the command. For simplicity, we have chosen to use the up and down arrow
keys (▲▲and ▲) in order to scroll through the menu and the E key for entering or executing a
command. Once you have pressed the E key and executed the final choice (for instance,
ON or OFF), the display backs up to the previous level of options.
Other methods for scrolling through the menu screen include rotating the VFO control or
press and hold the up and down arrow keys (▲▲and ▲) in order to scroll more quickly. Also
direct entry of the numbers in the flow chart will get you through the screens, but the other
screen options are not visible. This method should be used only after you have gone
through the manual at least once. A tearout shortcut card is provided in the front of the
manual to assist you in the direct entry method for commonly used features.
Another method for entering or executing the command, press the SELECT/MUTE key or press
the VFO/SELECT control.
Below is the first level of the Menu screen. These levels are then expanded on the foldout
towards the back of the manual. You will find a description section to explain the meanings
of these functions on the next few pages. Then, you will be walked through all the steps of
programming, scanning, searching, and trunktracking.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Menu Description and Numeric Keypad Equivalents
Below are the menu screens and a brief description or purpose of the feature.
1:SYSTEM DATA
1:DIMMER
Allows you to change the brightness of the display.
2:SCREEN MASK
Screen Mask allows you to limit what appears on the display to the alpha tags that
you have set for a channel along with a few function icons. Screen Mask removes
the frequency, receiving mode, tone data, signal strength bars, and the trunking
repeater activity indicators. This mode is particularly useful in public safety vehicles
where “information overload” is already a problem. Screen Mask does not work in
Search mode.
3:KEY BEEP
Use this function to turn off the keypad acknowledgement beep. The default setting
is on.
4:ENTER LOCK
Use Enter Lock to prevent accidental re-programming of channels and talkgroups
entered into memory. The default setting is off.
5:PC CONTROL
Use this function to set the transfer speed (baud rate) at which your personal
computer (PC) communicates with the scanner when downloading information into
your scanner using the third party software. See page 55 for details.
6:CLONE
You can clone all the programming, including frequencies, talkgroups and alpha
tags as well as bank settings and other parameters from one UBC780XLT to
another.
7:SMART SCAN
Not applicable.
8:DATA SKIP
A scanner will normally stop on any transmission it receives. This means the
UBC780XLT will occasionally stop on data signals and unmodulated transmissions.
You can automatically skip many of these types of transmissions during search.
9:SQUELCH MODE
The Squelch Mode allows you to set, at your option, whether the scanner will stop
on all active transmissions on a particular frequency or it will only respond to
transmissions with a pre-set sub-audible tone. This applies to both conventional
search and scan modes.The options are as follows:
1. CSQ - The default setting is CSQ (carrier squelch). In this mode the scanner
will stop on any transmission on a programmed frequency (Squelch mode does
not apply to trunking).
2. Tone SQ - In Tone Squelch mode, if you have set a subaudible tone (CTCSS or
DCS) for a frequency, the scanner will only stop on that frequency if the
transmission includes the prescribed tone.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
3. Tone Search - In this mode, as soon as the scanner stops on any (non-trunked)
channel, the scanner will begin to search for any subaudible tone that is being
used on a transmitted frequency. The scanner will check each CTCSS tone
sequentially and it will find DCS tones instantly.
0:BANK TAG
Allows you to set an alphanumeric text tag for individual banks in the scanner
(1-10).(The “0” key represents Bank number 10.) For example, you may wish to set
the Bank One text tag as Law Enforcement, the second bank as Fire, etc.
2:CHANNEL DATA
Choose the channel number. The following options are available for the selected
channel only. Repeat using a different channel number, if necessary.
1:ALPHA TAG
Allows you to set an alphanumeric text tag for individual frequencies that you have
programmed. For example, you can set CITY PD CH #3.
2:DELAY
The default delay for all programmed channels and talkgroups is two seconds. At
the end of any transmission the scanner will remain on the frequency for two
seconds before resuming scanning. This will allow you to catch most replies. You
can change the delay to 1, or 4 seconds as well as set no delay (the scanner will
immediately resume scanning after the end of a transmission). With the
UBC780XLT you can also set negative or inverse delays, also known as Pause.
With a 5 second pause, for example, the scanner will resume scanning after five
seconds even if the transmission you are currently listening to has not ended.
Finally, you can set an Infinite Delay. If a transmission is received on a frequency
with Infinite delay set, the scanner will stop on the channel and remain on it until
you have hit scan,
search, etc.
3:TONE DATA
You can set a CTCSS (analog) or DCS (digital) sub-audible tone for a frequency.
To do so you must have the Squelch Mode in the System Menu set to Tone
Squelch. You can also program a subaudible tone easily by pressing the E (enter)
key after programming a frequency. This will bring up the Tone Data menu without
your having to navigate the Menu. You can also lock a tone assigned to a
frequency. By doing this you will receive all transmissions on the frequency,
regardless of the subaudible tone, except the one which you have locked. Any
transmissions with that tone will not be received.
4:BEEP ALERT
You can set a Beep Alert on a per-channel basis to alert you when specific
frequencies are active. For example, you may wish to be alerted anytime a mutual
aid fire frequency is active. With beep alert, you will hear a rapid three-beep tone at
the start of each transmission that you have flagged as such. You will also notice
that as you scroll pass the flagged channel(s), you will hear the tones.
5:ATTENUATOR
The UBC780XLT comes with an RF Attenuation feature. If you are near an
unusually strong signal source, the signal may overload the scanner. The scanner
may stop repeatedly on that signal and miss other transmissions.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
The RF Attenuation feature works in all modes and attenuates (reduces) the
incoming signal strength to prevent stronger signals from overloading the scanner.
6:STEPS
Your UBC780XLT is programmed with default step sizes for each frequency range
(see Introduction page). Steps are important if you are interested in using the VFO
to tune off-frequency from a frequency programmed into memory or if you wish to
program a frequency that the default step size will not accept.
7:MODE
Default receive modes are also programmed into memory. AM for the aircraft and
CB bands, for example. All frequencies (other than TV broadcast audio) above 400
MHz are received in NFM mode which helps prevent adjacent channel interference.
You can change the default settings on a per-channel basis with this Menu item.
8:RECORD
You can flag any channel for recording using this menu function. The LINE icon will
become active for any such flagged channel. Use your own recording device
plugged into the jack on the back of the scanner.
3:TRUNK DATA
Choose the Trunk bank. The following options are available for the selected trunk
bank only. Repeat using a different trunk bank, if necessary.
1:TRUNK TYPE
You will need to assign the correct trunking type for the bank you are about to
program. If you want to listen to a Motorola Type 1 system, you will need to use
this menu option to assign the same.
Note: Some trunking systems require that you know the channel order. In these
cases you will also need to start programming the trunked system at the
start of the bank. The scanner defaults to the most common type of
trunking system, Motorola Type II.
2:DELAY
You can set delay for a trunk system on a bank by bank basis. If you’ve set delay
for 1 second, then there will be a one second delay in Trunk Search for that bank
and a one second delay for all the talkgroups you have programmed into Scan List
memory. You cannot set delay individually by talkgroup. The default delay is
two seconds.
3:RECORD
This Record option applies to Trunk Search. If you have set Record on, the LINE
icon will be lit. All talkgroups received during Trunk Search will be recordable
through the TAPE OUT jack on the back of the scanner. To record individual
talkgroups during Scan, see Item 5 on the next page. The default is off.
4:L/O ID REVIEW
Use this menu item to review the IDs that you have locked out during Search and
Scan. Use the Up/Down arrow keys or turn the VFO to the left or right to view the
IDs that have been locked out. To leave the lockout IDs unchanged, press MENU
to back out of the menu. To unlock an ID, press the L/O key. To unlock all the IDs
that have been locked out, press the E (Enter) key.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
5:PROGRAM ID
You can program IDs into Scan List memory either during Trunk Scan or Search
without going into the Menu. However, you can also use the Menu to program IDs.
This is particularly helpful when you are not near the trunked system you wish to
later monitor. You can set it up and have it ready to go at some later time.
After you have selected the Scan List location (1-10) and the memory location
(1-10), you can then do the following:
1
2
3
Program the talkgroup or I-CALL ID number
Set an alpha tag for same
Assign the Record option for same. Whenever a transmission is active on
the ID the signal can be recorded to a tape recorder using the TAPE OUT
jack on the back of the radio.
4. Assign a Beep Alert to the ID. Whenever that ID is active, you will hear a
rapid three beep tone at the start of the transmission.
6:ID LIST TAG
Assign an alphanumeric tag to any or all of the 10 Scan Lists for the system.
During Scan Mode, you will see the List Tag (on the bottom text line) along with
any alpha tag you may have set for an ID. In Search mode, you will see any Bank
Tag you have set.
7:I-CALL (MOTOROLA AND EDCS)
Most communications within a trunked system are group calls where one unit (such
as a dispatcher) communicates with all the units within his/her group (all the patrol
vehicles on the east side of town, for example). The units within this group
comprise what is typically known as a talkgroup. There are some communications
which are direct unit-to-unit conversations where one individual converses with
another individual. The call is initiated by a radio and is directed to another single
radio. Within the system, no one outside of these two users hears the conversation.
Your UBC780XLT defaults to I-CALL OFFmode. You can hear these conversations
by using this Menu item to turn the I-CALL function to ON. In Search mode, with
I-CALL on, you will hear both talkgroup calls and I-CALLs. You can also set I-
CALLs to I-CALL ONLY during which you will monitor only I-CALLs in Search
mode. You can also program I-CALL IDs into Scan List memory.
OR
8:ID SCAN LIST (LT)
When scanning an LT system you can only turn Scan Lists off and on when an LT
talkgroup that you have entered into memory is active. To provide you with another
method to turn Scan Lists on and off, you can use this Menu item which only
appears when you have selected LT in Trunk Type.
9:STATUS BIT (MOTOROLA)
On Type II trunking systems there is a method by which specialised types of
communications utilise unique talkgroup numbers. An emergency call will occur on a
unique talkgroup from its primary assignment, for example. Because the UBC780XLT
defaults to Status-Bit On mode, you never need to worry about missing these
transmissions. If you've programmed talkgroup 33264 into Scan List memory, for
example, and there is an emergency call within the group, you will hear it on 33264.
OR
Download from Www.Somanuals.com. All Manuals Search And Download.
15
10:EDACS ID FORM (EDCS)
You can change to display the talkgroups in decimal mode, but this mode does not
provide you with nearly the flexibility that you get with AFS. The UBC780XLT
defaults to show the talkgroup number in AFS mode (Agency-Fleet-Subfleet). For
details on AFS see pages 46.
11:END CODE (MOTOROLA)
When this function is disabled, the radio looks for squelch before returning to the
control channel instead of waiting for the disconnect tone. Only in rare instances
will you need to adjust the default settings.
The condition to return to control channels depends on whether signal is present or not.
12:CONTROL CH ONLY (MOTOROLA 800 & 900 SYSTEMS)
With this mode you will be able to track Motorola Type I and II 800 and 900 MHz
trunked systems by simply entering the control channel which manages the trunked
system. You will not have to program the voice channels. There are 4 channel
plans which you can select from.
4:SEARCH EVENT
You can program up to 10 search ranges (one per bank). The first time you
program a range for a bank you will need to do so through the Menu. After the first
time you can program a range as you do on most any other scanner, using the
numeric keypad and the ▲/HOLD or ▲/LIMIT keys.
1:SEARCH BANK
Use this Menu item to select the search bank that you want to program. You can
program banks 1 through 10, one at a time. For each of the banks, the following
options can be modified.
1:EDIT RANGE
Enter the upper and lower frequency limits of the search range.
2:STEPS
You can assign a variety of step sizes to the search range. Note: The
default step is usually acceptable and is listed in the front of the manual.
(See inside front cover)
3:MODE
You can change the default receive mode with this menu item.
4:ALPHA TAG
You can alpha tag any or all of the search banks.
2:DELAY
Set a delay for the search ranges. This applies to all ranges (See CHANNEL DATA-
STEPS for details).
3:ATTENUATOR
Set attenuation for all search ranges. (See CHANNEL DATA-ATTENUATOR
for details).
4:TONE DATA
The default mode is off. This means that you will receive all transmissions on any
frequencies that are active within your search range(s). By selecting CTCSS or
DCS you can set the radio to receive only a particular subaudible tone to be
Download from Www.Somanuals.com. All Manuals Search And Download.
16
received during your search. You can also lockout a particular CTCSS or DCS
tone. You may wish to do this if you want to search a range but not hear
transmissions on any frequency that have particular subaudible tone.
Note: Through the System Menu you can set the radio to operate in Tone Search
mode during Search as well. In this mode, the radio will automatically determine
the active subaudible tone on any frequency received during the Search.
5:RECORD
With Record set to on, any frequency that is active, during the search, can be
recorded to an external tape recorder.
6:AUTO STORE
You can automatically store active frequencies found during a search into memory.
You can select which bank you want to program the found frequencies. Note that
the audio will be muted during Auto Store.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Programming
Before the UBC780XLT can begin conventional scanning, you must program a frequency
into at least one channel. Repeat this procedure for each channel you want to program.
Storing Frequencies into Channels
1. Select desired frequency.
Here is a list of sample frequencies you can try:
156.800 Marine Calling channel
468.400 Police Channel
476.425 UHF CB
2. Press MAN.
3. Select a channel.
a. Enter the channel number.
b. Then press MAN.
4. Enter the frequency.
a. Enter the frequency number.
b. Then press E.
Note: • To clear a mistake while entering the frequency, press
(decimal key) repeatedly
until the display is cleared.
• If you enter a channel or frequency which is out
of the scanner’s range, a distinctive beep will
sound and ERRORappears in the display.
• You can use ▲ or ▲ when selecting a channel.
Press and hold ▲ or ▲ for 1 second to move up/down more quickly.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Duplicate Frequency Alert
If you enter a frequency which has been stored in
another channel, you will hear a beep and the other
channel displays WARNING.
Press
to clear and start again.
––– OR –––
Press E again to store the frequency in both channels.
Storing Text Tags
You can customise your scanner by storing text tags for easy identification of banks, channel
transmissions, trunking talkgroup IDs, etc. The text tags can be set at the menu mode.
(Refer to Understanding Menu System on page 11.)
Assigning a Bank Tag to a Bank
1. Press MENU.
2. Press E to select SYSTEM DATA.
3. Press ▲▲or ▲▲to select BANK TAG and then press E.
4. Select the bank number to be tagged using ▲ or ▲
and then press E.
5. The cursor appears on the display. Rotate VFO to change
letters, and then press ▲ or ▲ to shift right or left. Both
capital and lower case letters are available, as well as
numbers and punctuation marks.
6. After entering the desired text, press E or SELECT.
▲▲ Remember! You can also use the VFO control for scrolling. To clear a mistake while
entering the frequency, press
(decimal key) repeatedly until the display is cleared.
Assigning a Text Tag to a Channel
1. Press MENU.
2. Press ▲▲or ▲▲to select CH DATA and then press E.
3. Select the channel number to be tagged using ▲ or ▲ and pressing E. You can also
enter the channel number in using the keypad and then press E.
4. Press ▲▲or ▲ to select ALPHA TAG and then pressing E.
Note: • If you have not stored a frequency in the channel,
UNREGISTEREDwill appear in the display.
5. The cursor appears on the display. Rotate VFO to
change letters, and press ▲ or ▲ to shift right or left.
Both capital and lower case letters are available, as
well as numbers and punctuation marks.
6. After entering the desired text, press E, SELECT or VFO.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Beep Alert
The scanner can alert you with three rapid beeps at the beginning of a transmission on an
assigned frequency.
Assigning the beep alert to a channel
This alert can be set on/off to every channel (or to every ID memory for Trunking mode).
1. Press MENU.
2. Press ▲▲or ▲▲to select CH DATA and then press E.
3. Select the channel number to be tagged using ▲ or ▲ and then press E. (You can also
enter the channel number in using the keypad or VFO control and then press E.)
4. Press ▲▲or ▲ to select BEEP ALERT and then press E.
5. Press ▲▲or ▲ to select ON or OFF and then pressing E.
Note: If NOTREGISTERappears, make sure a frequency is stored in the channel.
Programming Tips
• Group similar services into a bank. For example, program police frequencies in channels 1
through 10 and fire/emergency into channels 51 through 60, and so on.
• Put the frequency that you listen to the most or the most important frequency into a
Priority channel.
• To quickly program a series of channels, start with the lowest number channel.
For example, when you are programming five new frequencies into Channels 4 through
8, start with Channel 4. After you finish programming a channel, press MAN or HOLD/▲
to go to the next higher channel.
• Write down your programmed channels and frequencies and put in a convenient place in
case of accidental reprogramming.
• Frequencies are rounded off according to the step of each channel.
• When you are overwriting a tagged channel with a new frequency, the previous alpha tag
will be deleted. You must re-enter the alpha tag.
• When programming frequencies, a 2 second delay is set automatically but can be
changed in the Channel Data menu.
Deleting a Stored Frequency
To delete a stored frequency:
a. Select a channel.
b. Press 0.
c. Then press E.
SERVICE SEARCH
Note: Channels with no frequencies are automatically locked out.
PUBLIC SAFETY
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Scanning
1. After programming frequencies, simply press SCAN to
begin scanning.
2. The bank indicators selected for scanning appear in the display, and the bank being
currently monitored flashes. You can deselect banks from active scanning by pressing
their number on your keypad. The indicator for each deselected bank turns off, and the
banks channels are not scanned.
Note: One Bank must always be active. You cannot deactivate all ten banks at the same
time. If you try to turn off all the banks, the first bank is automatically selected.
To restore a bank to active scanning, press the banks number on your keypad.
The banks indicator will display again.
SCAN
3. During normal scanning the scanner skips
unprogrammed or locked out channels.
CHANNELS
1
2
3
4
5
6
7
8
9
10
4. When a transmission is received, the scanner stops
on that channel. When the transmission ends,
scanning resumes automatically.
Frequency
Locked Out
(L/O)
Frequency
not entered
If you want to stop on a channel during scanning,
press MAN.
If you want to resume scanning,
press SCAN.
To directly access a specific channel:
There are several ways to access a specific channel quickly.
1. Press MAN.
2. Using the keypad, enter the channel number.
3. Press MAN again.
Another method is as follows:
1. Press the VFO control until CHAN is displayed.
2. Rotate the VFO control until the desired channel is
displayed. The scanner will automatically go to
manual mode.
Note: You can accidentally change the frequency if you don’t
verify that CHAN is displayed. If FREQ is displayed, you
will be changing the frequency when you rotate the
VFO control. Just don’t press E or it will be changed!
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Still another method of direct access to a specific channel:
1
2
Press MAN.
Press ▲▲or ▲ to select the channel. (or press and hold ▲ or ▲ to scroll more quickly.)
Lastly to step up through the channels one at a time, repeatedly press MAN.
RF Attenuation Feature
The UBC780XLT comes with an RF Attenuation feature. If you're near an unusually strong
signal source, the signal may overload the scanner. The scanner may stop repeatedly on
that signal and miss other transmissions.
The RF Attenuation feature works in all modes and attenuates (reduces) the incoming signal
strength to prevent stronger signals from overloading the scanner.
The RF attenuation is set at the menu mode.
1. Press MENU.
2. For Search mode, press ▲ or ▲ to select SEARCH
EVENT and then press E.
OR
For Scan mode, press ▲ or ▲ to select CH DATA
and then press E. Then you must enter your channel
data by pressing ▲ , ▲ or direct keypad entry. Then
press E.
3. Press ▲ or ▲ to select ATTENUATOR and then
press E.
4. Set to ON using ▲ or ▲ and then press E.
ATTappears on the display.
▲▲ Remember! You can also use the VFO control for scrolling. Also instead of pressing
E, you can press the VFO/SELECT control or press the SELECT/MUTE key.
Note: Attenuation will only be active for the specified channel. In SEARCH mode, it is
applied to the search ranges in all banks.
Setting the Delay Mode
A default delay of 2 seconds is automatically set for each frequency or talkgroup. A different
delay can be set for each programmed channel so that when scan or search stops on a
channel there is a brief pause before the scanning cycle resumes. To set the delay feature,
enter into the menu mode.
1. Press MENU.
2. Press ▲ or ▲ to select CH DATA and then press E.
3. Select the channel number to be delayed using ▲ or ▲ and
then press E.
4. Press ▲ or ▲ to select DELAY and then press E.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
5. Press ▲ or ▲ to select one of the delay periods
provided and then press E. DLYappears on the
display unless no delay has been set.
6. For Search mode, select SEARCH EVENT - DELAY, then set the delay period.
Note: The delay periods are as follows:
• None: Delay feature off
• 1 sec.: Delays for 1 sec. before re-scanning
• 2 sec.: Delays for 2 sec. before re-scanning
• 4 sec.: Delays for 4 sec. before re-scanning
• Infinite: Stays on until SCAN is pressed
• -2 sec.: Stays for 2 sec. only before re-scanning *
• -5 sec.: Stays for 5 sec. only before re-scanning *
• -10 sec.: Stays for 10 sec. only before re-scanning *
*Setting negative delay periods are useful if you are only interested in small
segments of conversations. For example: If you set a -5 second delay, you will only
hear 5 seconds of the conversation and then the scanner will resume scanning,
whether or not the conversation is finished.
Channel Lockout
You can lockout any channel so it is not checked during normal scanning. You can restore the
channel to scanning when you wish.
Lockout in Manual Mode
1. Press MAN.
2. Select a channel.
Enter the channel numbers.
Press MAN again.
MUTE
––– OR –––
Press MAN or HOLD/▲ to change higher,
or LIMIT/▲ to lower the channel.
3. Press L/O to lockout the channel.
L/Oappears in the display.
Lockout in Scanning Mode
If the scanner keeps stopping on a particular channel due to noise or too frequent
transmissions, you may want to keep that channel from scanning.
1. Wait until the scanner stops at the channel.
2. Then press L/O.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
3. The scanner immediately resumes scanning because the
locked out channel is no longer in the scanning sequence.
Lockout Tips
• Write down your locked-out channels and put in a convenient place in
case you need to restore them.
Restoring a Locked-out Channel
1. Press MAN.
2. Select a locked out channel.
a. Enter the channel number.
b. Then press MAN again.
3. Press L/O to unlock the channel. The L/Oicon goes out.
Restoring All Locked-out Channels
You can restore all locked-out channels in a bank only when a bank is selected for scan. If
you have deselected a bank and you want to restore all of its locked-out channels using the
steps below, you must press SCAN and then press the number of the bank on your keypad.
1. Press MAN.
Note: You must be in Manual mode before restoring all
locked-out channels.
2. Press and hold L/O for about two seconds.
You will hear two beeps when all the channels have
been restored.
MUTE
Priority Scan
When Priority Scan is turned on, your scanner checks the priority channel every two
seconds for activity. If a signal is present on the priority channel, your scanner monitors the
channel until the transmission ends, then resumes normal scanning. You can designate one
channel in each bank as a Priority Channel. By default, the first channel in each bank is the
priority channel, but you can change this.
To activate Priority Scan (in either the Manual or Scan Mode):
1. Press PRI.
Note: If you have locked out the priority channel,
ERRORmessage appears when you select
Priority mode.
2. Press PRI again at anytime to deactivate Priority Scan.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Changing the Priority Channel
You cannot eliminate the Priority Channel, but you can change it to any one of the 50
available channels in each bank.
1. Press MAN.
2. To select a new Priority Channel:
a. Enter the channel number.
MUTE
b. Then press MAN again.
3. Press and hold PRI for two seconds to designate this
channel as your new Priority Channel.
Two beeps indicate that the Priority
channel has been changed. The P icon appears in
the display.
Note: • Priority in Trunking mode works just the same, except instead of setting priorities
for channels, you set them for talkgroup IDs. The scanner only checks priority
talkgroups between transmission, not in 2 second intervals.
• Priority scan is disabled while the TRUNK icon is lit (an error tone will sound
if you try). To make it possible, turn off the TRUNK icon then press PRI.
• At Priority scan, it scans the designated Priority Channels in the banks
you selected.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Searching
Setting a Search Range
Note: First you must set the search ranges through the menu screen prior to any searching.
The UBC780XLT can search up to 10 separate frequency ranges to help you discover new
stations in your area.
To set a search range, enter into the menu mode.
1. Press MENU.
2. Press ▲▲or ▲ to select SEARCH EVENT and then press E.
3. Press ▲▲or ▲ to select SEARCH BANK and then press E.
4. Press ▲▲or ▲ to select the desired bank number and then press E.
5. Press ▲▲or ▲ to select EDIT RANGE and then press E.
6. Enter the lowest frequency using the keypad and
then press E, then repeat the same for the
highest frequency.
Then press SRCH.
Note: • The scanner can search up to 10 ranges by selecting specific banks which you
have programmed search ranges. (Chain Search)
• You can select or deselect the search bank freely by pressing the corresponding
number with the keypad.
• The scanner automatically increases its search speed from 100 to 300 steps per
second for the bands having 5 kHz steps. (Turbo Search)
• Press and hold ▲ or ▲ for more than 2 seconds while searching to switch the
search direction.
• When searching in WFM, it stops before reaching the desired frequency if the step
is other than 50 kHz or 100 kHz.
• After you have set the Search Range through the Menu the first time for a bank,
you will be able to set new ranges for the same bank by using the keypad and the
standard direct entry method.
Note: After you have entered the search range in a selected bank while still in the menu
mode, you can set your alpha tag (see page 19), change the step size of the search,
or change the mode. Once the lower and upper parameters of your search are
edited, the menu screen backs up one level to allow you to modify the step size,
receive mode, and alpha tag. Select 2: STEPSfor your step size choices and then
Download from Www.Somanuals.com. All Manuals Search And Download.
26
press E. Select 3: MODEfor the receiver mode choices and then press E. Select
4: ALPHA TAG to enter an alpha tag using the VFO control.
Search Hold Feature
1. Press HOLD/▲ at anytime to stop the search.
2. Press HOLD/▲ to move to the next higher frequency.
––– OR –––
Press LIMIT/▲ to move down to the previous frequency.
3. Press SRCH to resume searching.
Data Skip
A scanner will normally stop on any transmission it receives. This means the UBC780XLT
will occasionally stop on data signals and unmodulated transmissions. You can automatically
skip many of these types of transmissions during search. To activate the data skip feature,
enter into the menu mode.
1. Press MENU.
2. Press ▲▲or ▲ to select SYSTEM DATA and then press E.
3. Press ▲▲or ▲ to select DATA SKIP and then press E.
4. Set to ON using ▲, ▲ or VFO and then press E.
DATAappears on the display.
When data skip is active, your scanner may pause momentarily on an unwanted signal but
will resume searching in 2 or 3 seconds. Data Skip does not function during AM/WFM band
scan, chain search, or SVC search, Priority Scan, and Trunking Mode.
Frequency Skip
If a particular frequency continues to interrupt search scanning, it is possible to set your
scanner to skip the frequency.
To skip over a frequency, press L/O when stopping at the frequency you want
to skip.
Note: • You can program up to 200 skip frequencies.
The 201st skip frequency entered causes the
first skipped frequency to unlock.
• If all frequencies in the search range are set to
MUTE
skip, it moves to Search hold mode.
To resume searching, do as follows:
1) Cancel the frequency skip set, or
2) Reset the search frequency range.
To cancel all skipped frequencies, press and hold L/O for 2 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Storing Search Frequencies
You can quickly store any frequency you find during Search.
Caution: You must select the channel in which you will store the frequency before entering
the search mode. Otherwise, you may erase a stored frequency that you want
to keep.
1. During search, press HOLD/▲ when the scanner
stops at the frequency you want to store.
2. Press E to store the frequency in the channel you selected.
Note: • If the frequency you want to store exists already, WARNINGappears on the display
with a beep. (See Duplicate Frequency Alert on page 19.)
• After storing the frequency, it moves to the manual mode.
3. To store another frequency, select another channel for the new frequency by pressing
MAN or HOLD/▲ or LIMIT/▲.
4. Repeat steps 1 and 2 after starting search for all the Search frequencies you want
to store.
Auto Storing
The scanner automatically stores searched frequencies if its auto store feature is activated.
To make use of this feature, set a search range first (see page 26), then enter into the menu mode.
1. Press MENU.
2. Press ▲▲or ▲ to select SEARCH EVENT and then press E.
3. Press ▲▲or ▲ to select AUTO STORE and then press E.
4. Set to ON using ▲, ▲ or VFO and pressing E. All
bank numbers start flashing and AUTO is lit on
the display.
5. Select the bank numbers you want to use with the
keypad. The selected bank numbers stop flashing.
Note: If the selected bank has no free channels to store,
ERRORwill appear on the display with a beep.
6. Press SRCH to start auto storing.The AUTO icon on the display
begins to flash. Audio is muted during the storing process.
7. After the search has gone through the search
range, press MAN or MENU to stop this feature.
STORE END appears in the display. You
may want to let it run through the search range
again because during the first pass there
may not be any transmissions at that
particular time.
▲▲ Remember! You can also use the VFO control for scrolling. Also instead of pressing
E, you can press the VFO/SELECT control or press the SELECT/MUTE key.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Squelch (SQ) Mode
The scanner can be set to the following SQ modes.
• Carrier SQ mode (default setting)
The scanner will stop on any transmission or squelch opening, regardless of whether any
sub-audible tone has been programmed for the channel or search range.
• Tone SQ mode
The scanner will stop on any active frequency for which either no sub-audible tone has
been programmed or for which the user-programmed sub-audible tone is also active.
• Tone Search mode
During any transmission, the scanner will begin searching all possible sub-audible tones,
one of which may also be in use. The scanner counts up through the CTCSS tones and
instantly determines any possible DCS tone. See Page 83 for a listing of the tones that
the UBC780XLT decodes.
Note: When Tone Search is active in Scan Mode, once the CTCSS/DCS display flashes
a tone repeatedly (meaning that it has found the tone match), you can press E to
program that frequency with the captured tone. When you change the mode to
Tone Squelch from Tone Search, that frequency and tone will be programmed.
• Tone Lock (out) mode
For either a memory channel or a search range, you can lock a particular sub-audible
tone by pressing L/O after scrolling to the desired tone. The scanner will stop on any
transmission except those which may be using the locked sub-audible.
To set your scanner, enter into the menu mode.
1. Press MENU.
2. Press ▲▲or ▲ to select SYSTEM DATA and then press E.
3. Press ▲▲or ▲ to select SQ MODE and then press E.
4. Press ▲▲or ▲ to select one type (CSQ, Tone SQ, Tone Search) and then press E.
5. To set Tone Lock mode, do the following first, then select Tone SQ in step 4.
1) For scan mode, enter CH DATA - CH No. - TONE DATA, select CTCSS/DCS with
▲ or ▲, set Tone Lock ON by pressing L/O.
2) For search mode, enter SEARCH EVENT - TONE DATA, select CTCSS/DCS with
▲ or ▲, set Tone Lock ON by pressing L/O.
Note: • CTCSS: Continuous Tone Coded Squelch System.
• DCS: Digital Coded Squelch.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
• For example, the scanner shows the following displays
Tone SQ on,
Tone SQ on,
DCS 325 set
Tone SQ on,
CTCSS 123.0 Hz set
No CTCSS & DCS set
Tone Search,
Tone Search,
Tone Search,
CTCSS 67.0 Hz detected
DCS 023 detected
no signal present
•
If the delay feature (-2 sec/-5 sec/-10 sec) has been set while in Tone search mode,
it resumes scanning according to the delay setting.
Additional Menu Options for Searching
Each of these additional menu options apply to all banks with search ranges entered. If
there is a bank that you do not want an option to apply, then simply press the bank number
on the numerical keypad. You will see the bank number that you have selected, disappears
from
the display. (For more information on these options refer to the “Menu Descriptions” section
and “Additional Features” section.
Options:
RECORD (for more information see page 9)
1. Press MENU.
2. Press ▲▲or ▲ to select SEARCH EVENT and then press E.
3. Press ▲▲or ▲ to select RECORD and then press E.
4. Set to ON using ▲, ▲ or VFO and pressing E.
LINE is lit on the display.
ATTENUATOR (for more information see page 22)
1. Press MENU.
2. Press ▲▲or ▲ to select SEARCH EVENT and then press E.
3. Press ▲▲or ▲ to select ATTENUATOR and then press E.
4. Set to ON using ▲, ▲ or VFO and pressing E.
ATT is lit on the display.
DELAY
Refer to page 22.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
ADDENDUM SHEET
Service Search
The Service Search feature allows you to toggle through the following five preprogrammed
services. The frequencies selected for these services are the most commonly used around
the Australia.
• 1: POLICE
• 2: RAILROAD
• 3: AIR
• 4: MARINE
• 5: UHF CB
1. Press SVC the display indicates
as illustrated.
:
1 POLICE
2. After a 3 second delay, searching begins for the first
preprogrammed service – Police (initial setting).
:
2 RAILROAD
3. If you want to skip a frequency, press SRCH to start searching immediately.
4. To change the searched service, use ▲, ▲ or VFO after pressing SVC.
Note: • You can not change such settings as delay, during a service search.
• The channel number corresponding to certain services will appear when a
frequency within the search is active.
• You can enter one of the Service Search frequencies into Channel Memory by
pressing E when holding on one of the frequencies.
5.
To exit from the service search mode, press MAN or SCAN.
During the search of one of the preprogrammed services, the lower display line will indicate
the service that you are searching. To stop the search, press HOLD/▲. HOLDappears in the
display. Press HOLD/▲ or LIMIT/▲ to move up or down one programmed frequency, or press
SRCH to resume scanning.
Service Search Skip
You can set the scanner to skip the frequencies unwanted during service search. 100
skipped frequencies are programmable.
1. To skip over a frequency, press L/O when stopping at the frequency you want to skip.
2. To cancel a skip during search, press HOLD/▲,
tune in the desired frequency using ▲, ▲ or VFO,
then press L/O.
SERVICESEARCH
To restore all skipped frequencies, press L/O for 2 seconds.
POLICE
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Trunked Systems
Your UBC780XLT is designed to track three major types of trunked radio systems. These
systems are described here.
▲MOTOROLA - Including Type I, Type II, Hybrid, SMARTNET, and Privacy Plus.
Motorola systems are widely used by public safety and business users. Most are on
the 800 MHz band, and recent systems are appearing on other bands.
▲EDACS - Including "Wideband" 9600 baud, and "Narrowband" 4800 baud systems.
"Wideband" systems are mostly on the 800 MHz band, and are used by public safety,
utilities, and business users. Some systems are used on the VHF and UHF bands.
"Narrowband" systems are used in the 935-940 MHz band, many by utilities.
(See page 49)
▲LTR - These systems are mostly for business users, and found on the UHF,
800 and 900 MHz bands. (See page 48)
For details on the operation and programming for all of these systems, see pages 32-34.
When tracking these types of systems, remember these important points:
• Your scanner defaults to monitor Motorola Type II systems; however, you can change this
if the system in your area is different. (The types of systems are discussed in the following
pages.)
Note: *Motorola, SMARTNET, and PRIVACY PLUS are trademarks of Motorola Inc. EDACS is a
registered trademark of the Ericsson Corporation. LTR is a registered trademark of E.F.
Johnson Company.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Programming and Receiving
Trunked Systems
Programming Trunking Frequencies
The first step in tracking a trunked system is storing the frequencies in one of the 10
available banks in your scanner. Remember that you can only store one trunking system in
each bank.
Important: If you are programming an EDACS or LTR trunked system, you must enter the
frequencies in a specific order. Check the frequency guide included with the
scanner for the frequencies in your area.
1. Press MENU.
2. Press ▲▲or ▲ to select TRUNK DATA and then
press E.
3. Press ▲▲or ▲ to select the bank no. and then press E.
4. Press ▲ or ▲ to select the TRUNK TYPE and then
press E.
▲▲ Remember! You can also use the VFO control for scrolling. Also instead of pressing
E, you can press the VFO/SELECT control or press the SELECT/MUTE key.
5. Choose the system you want to track using the
keypad, ▲ or ▲ and then press E.
No. LCD display
Icon Trunking Type
Special requirements
1
2
3
4
5
6
7
8
Type 2 800
Type 1
M
M
M
M
M
E
Motorola Type 2 800 MHz
Motorola Type 1
a. Must program a fleet map.
Type 2 900
Type 2 UHF
Type 2 VHF
EDCS WIDE
EDCS Narrow
LT
Motorola Type 2 900 MHz
Motorola Type 2 UHF
Motorola Type 2 VHF
EDACS Wideband 9600 baud
EDACS Narrowband 4800 baud
LTR
b. Must program base, spacing,
frequency and offset channel.
c. Must program frequencies
in exact order
E
L
and location.
4. To exit from this mode, press MENU repeatedly.
5. Select a channel using the keypad and then press MAN.
6. Enter a frequency for the trunked system using
the keypad.
For example, enter 867.8375(Type 2) or enter a
frequency you are going to track.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
▲
Important!
7. Press TRUNK for 2 seconds.
A tone sounds, and E, M, or Licon appears on the
display according to the system selected.
Note: • To clear a mistake while entering the frequency,
press
(decimal key) repeatedly until the
display is cleared.
• If you enter a frequency which is out of the
system’s trunking range, a distinctive beep
sounds and ERRORappears on the display.
• Repeat Step 7 for every trunk frequency
entered.
Selecting Trunking Programming Menu Mode
To change the system type which your scanner monitors, you must be in the Trunking
Programming menu mode.
To select this mode, follow these steps:
1. Press MENU.
2. Press ▲▲or ▲ to select TRUNK DATA and then
press E.
3. Select the bank you want to program using ▲, ▲ or VFO and then press E.
▲
Remember! You can also use the VFO control for scrolling. Also instead of pressing
E, you can press the VFO/SELECT control or press the SELECT/MUTE key.
Selecting Trunking System Type
1. Select TRUNK TYPE using ▲, ▲ or VFO and then
press E, SELECT or VFO.
2. Select the system type you want to program
using ▲, ▲▲or VFO and then press E, SELECT
or VFO.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Setting the Squelch
For trunked reception, a good setting for the SQUELCH control is in the centre of the range
with the red marker pointing up. See the illustration.
If set too high (CCW) in some cases it could prevent your scanner from
locking to the control channel reliably. If set too low (CW) it will slightly
delay finding the control channel. The best setting is the same as for
conventional reception, and is not critical.
Receiving Trunked Systems
When you have properly programmed all the frequencies for a trunked system, you can
receive the system several different ways. You will find that Search, Hold, Lockout, Scan and
Manual are all similar to conventional scanning.
▲
▲
TRUNKED SEARCH lets you hear all system talkgroup activity (unit-to-unit I-Calls
may be received as well). This is the best way to get started.
ID HOLD works with Search mode to let you quickly freeze reception on an
interesting transmission. Or you can manually specify a talkgroup with DIRECT
ENTRY ID HOLD.
▲
▲
▲
ID LOCKOUT works with Search to exclude talkgroups that you don't want to hear.
ID SCAN lets you receive only those talkgroups that you store in Scan Lists.
MANUAL lets to selectively listen to a talkgroup in your Scan Lists
When receiving EDACS systems, remember that Uniden's AFS talkgroups give you powerful
flexibility. In a few keystrokes, you can specify a single talkgroup, a fleet, or an entire agency
in all the above modes. Read the section "EDACS Reception" to understand how this works.
Trunked Search
Once you have programmed all the frequencies for a trunked system, SEARCH will let you
immediately start hearing transmissions. It is suggested you try SEARCH mode first.
1. Press SCAN, and select the bank(s) you wish to receive, just as you select banks in
conventional scanning.
2. Press TRUNK to enable trunked reception. The radio will seek and acquire the trunked
system control channel. The scanner will now be in MONITOR mode. You will hear the
control channel and see active talkgroups on the screen. You will not hear the voice
transmissions in MONITOR mode.
▲ Hint: MONITOR mode is an excellent way to observe system activity and determine
which talkgroups are most active. Locked-out IDs display during MONITOR mode.
3. Press SRCH to begin searching and receiving. You will hear talkgroups and see them on
the screen.
Talkgroups display differently in Motorola, EDACS and LTR systems. You should read the
appropriate parts of this guide to understand the formats.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
The bottom line of the display indicates the Bank and the type of trunked system you are
monitoring. You can change this to display a bank tag by using the System Menu.
Regardless of the system, you won't know exactly who you are receiving until you listen for
a while. Of course, figuring out who each ID represents is half the fun of TrunkTracking.
Later, when you learn more about a system, you will want to store lists of talkgroups.
Then you can scan specific agencies and users, and use the many other features your
radio provides.
ID Hold and Direct Entry ID Hold Mode
Just like in conventional Search, HOLD lets you pause ID Search on an interesting
transmission without storing the talkgroup into memory.
If you hear an interesting ID during SEARCH mode, and want to continue listening to it --
• Press HOLD/▲ to stop the search. HOLDappears in the display.
If you want to listen to a specific ID, while in HOLD --
• Use the keypad to enter the ID you want and press
HOLD/▲. HOLDappears in the display.
If you want to stop holding --
• Press SRCH to return to Search Mode.
ID Lockout
Like conventional scanning, it’s possible to lockout unwanted traffic. This is particularly
important in trunked systems because in many areas, water meters, door alarms, traffic
signals, and other mechanical devices are assigned IDs just like other users. Also some
users scramble or encrypt their communications, and you may want to lock out these
unintelligible broadcasts.
To lockout an ID, press L/O when the ID displays.
The ID is locked out. You can lockout up to 200 IDs.
Note: If you lockout an ID in Search mode, it is also locked out in Scan List mode.
Conversely, if you lockout an ID while in Scan List mode, it is locked out in Search
mode. For information about Scan Lists see page 42.
EDACS BLOCKOUT is a powerful form of ID LOCKOUT that can be used only with AFS
and EDACS systems. This feature lets you lock out entire Agencies or Fleets, not just
individual talkgroups. Using ID BLOCKOUT you can, for example, prevent Search from
stopping on any of hundreds of talkgroups in the Utilities agency. You can do this with just a
few keystrokes. To use ID BLOCKOUT just enter the Agency- part, or the Agency-Fleet part,
of the talkgroup code and press L/O. For example, to Blockout Agency 4 in Trunk Search,
press HOLD/▲, 04,
(decimal key), and then L/O. For other ways to use partial AFS entry,
be sure to read the section "EDACS Reception".
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Restoring Locked-out IDs
To unlock a single ID, follow these steps:
1. Press MENU.
2. Select TRUNK DATA - BANK NO. - L/O ID REVIEW
using ▲, ▲ or VFO and pressing E, SELECT or VFO.
3. Select the locked out ID you want to unlock using ▲ or ▲.
4. Press L/O. The ID is unlocked and the next locked ID displays.
To unlock all locked out IDs in a bank at once:
1. Press E instead of L/O in step 4 above.
2. To exit from this mode, press MENU repeatedly.
Channel Activity Indicators
The UBC780XLT has 30 Channel Activity Indicators to visually display a trunked systems
activity. You’ll always know which frequencies are in use and how much communication
traffic is occurring.
Each frequency you program in a trunking bank corresponds to an activity indicator at the
top of your scanners display. The way in which the Activity Indicators display provide you
with information about the system you’re tracking.
• The indicator which remains on, even if when there is
no traffic, represents the frequency being used as the
data channel.
• If an indicator turns on and you don't hear a
conversation, then the channel may be used as a
telephone interconnect call (some systems) or a
talkgroup that has been locked out.
• The indicator which flashes when an ID displays
represents the frequency being used by the talkgroup.
• If you're holding on an ID which isn't active, the
activity indicators will turn on and off as other groups
use the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Scan Lists
Each bank of your UBC780XLT can be a trunk tracking bank and it can be a conventional
scanning bank. When you designate a bank as a trunking bank, your scanner sets up 10
Scan Lists, which are simply lists used to store your favourite IDs. Each list can contain up
to 10 IDs, so you can store a total of 100 IDs for each trunk tracking bank. (1000 if you use
all banks as trunking banks!)
Scan Lists help you organise the trunking system users into categories.
For example, you might use List#1 for police IDs, List#2 for fire department IDs, List#3 for
emergency medical service IDs, etc. Once IDs are stored in lists, you can scan them like
you scan conventional frequencies and you can lock out any one (and up to 9) of the 10
scan lists by pressing the corresponding numeric key. When an ID is active, the scan list
number icon into which it is programmed will flash in the display (when the LIST icon is also
active – see below). You can program your scan lists either manually or during trunking
search mode.
SELECT Key
Use the SELECT key while trunking to toggle between viewing the active Banks and the
active Scan Lists. To see which is currently active, check the display for either the BANK or
the LIST icon.
Programming ID Scan Lists Manually
1. Press MAN, the lowest available ID list number appears on the display.
2. Use HOLD/▲ and LIMIT/▲ to select the Scan List
location you want to program.
For example, select the third memory location in the
fifth scan list.
Note: You can also use the keypad to input directly.
3. Enter the Type II ID you want to store, and press E.
––– OR –––
To enter a Type I ID:
a. Enter the block number and fleet number.
b. Press
.
c. Enter the subfleet number, and press E.
––– OR –––
Download from Www.Somanuals.com. All Manuals Search And Download.
38
To enter an EDACS® ID:
a. Enter ID you want to store.
Use the
for the “dash”.
b. Press E.
Hint: Remember that Uniden's AFS format allows you to enter full or partial EDACS IDs for
powerful flexibility in all modes. Be sure to read the section "EDACS Reception" on
page 49 to learn how this works.
Note: The UBC780XLT defaults to “AFS” talkgroup displays for EDACS® only.
––– OR –––
To enter a LTR ID:
a. Enter Area code and then press
.
b. Enter Home Repeater number and then press
.
c. Enter ID you want to store and then press E.
Note: To clear a mistake while entering an ID, press
and E successively, and
start over.
4. Press MAN or HOLD/▲ to select the next Scan List location.
Program ID Manually with the Menu Mode
Note: It is also possible to do ID programming in the menu mode by selecting TRUNK
DATA - BANK NO. - PROGRAM ID. Do the following:
1. Press MENU.
2. Press ▲▲or ▲ to select TRUNK DATA and then
press E.
3. Press ▲▲or ▲ to select the bank no. and then press E.
4. Press ▲ or ▲ to select the PROGRAM ID and then
press E.
▲▲ Remember! You can also use the VFO control for scrolling. Also instead of pressing
E, you can press the VFO/SELECT control or press the SELECT/MUTE key.
5. Select the ID location using the VFO control, keypad,
▲ or ▲ and then press E. (first number represents
the bank number and second number represents the
memory location.)(Direct entry method example:
enter “5-1” by pressing 5,
,1.)
6. Press ▲▲or ▲ to select ID and then press E.
7. Enter the ID number using the keypad and then press E.
Note: After you have programmed the ID in a selected bank while still in the menu mode,
you can set your alpha tag (see page 19), flag the individual ID or talkgroup for
recording (see page 30 and 9), or turn on the beep alert for an individual talkgroup
(see page 20).
Download from Www.Somanuals.com. All Manuals Search And Download.
39
ID Scan Mode
1. Press SCAN to begin scanning the lists you
have programmed.
If you haven't programmed any IDs, ERRORappears
for a few seconds.
2. To remove a Scan List from active scanning, press
the number of the Scan List on your keypad.
The Scan List indicator turns off, and the IDs in that
list are not scanned.
Note: One Scan List must always be active. If you try
and deactivate all the Scan Lists, Scan List 1 will
automatically be active.
3. To restore a Scan List to active scanning, press its
number again.
4. Press SRCH to return to Trunk Tracking Search mode.
For motorola and EDACS system, to change your
display between the Scan List indicators and trunk
bank display, press SELECT.
For LTR systems only, the talkgroup must be active in
order to change the scan list and bank indicators. If
the talkgroup is not active, change the scan list by
using the menu screen.
Note: • Once you press SCAN or SRCH in one bank, all trunking banks will change to
that mode.
• Selecting a Scan List is also possible in the menu mode. (LTR only)
• ID SCANNINGappears on the bottom of the screen during Trunk Scan instead of
simply SCANNING.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Setting Priority in Trunking Mode
You can set priority in your trunking lists, just as you do in your conventional ones. You can
set the priority by pressing and holding PRI for 2 seconds. After you’ve set up your Scan
List, press PRI to activate it.
It’s very similar to conventional priority although there is no “interrupt” during the
transmissions. Priorities are checked in between transmissions.
With Priority on, you can hold on an ID in your Scan List, such as Scan List 6, memory
position 7, and the scanner will check all the priorities in all the active Scan Lists every few
seconds and in between any transmissions on the ID on which you’re holding. The lowest
numbered priority will be checked first. For example, the priority ID in List 1 will be checked
before the priority in List 2, etc.
Note: This function does not work in LTR tracking.
Programming Scan Lists During Search
To select a Scan List location and store an ID during Search mode, follow these steps:
1. When your scanner stops on an ID you want to store,
press HOLD/▲.
2. Press E, or use HOLD/▲ or LIMIT/▲ to select the Scan
List memory location you want to change, then
press E.
3. Press SRCH to return to Trunk Tracking Search mode.
Deleting a Stored ID
To delete a stored ID:
a. Press MAN.
b. Use HOLD/▲ and LIMIT/▲ to select the scan list
location you want to delete.
c. Press 0.
d. Then press E.
Moving between Scan List Memories
There are a number of ways to step and move through your Scan List memories:
1. Press MAN repeatedly.
2. Or, press MAN, then press HOLD/▲ or LIMIT/▲.
3. Or, press MAN, next press 0 - 9 (scan list number), then press 0 - 9 (memory position), for
example. To move to Scan List 4, memory position 10, press: MAN, 4, 0, MAN
Download from Www.Somanuals.com. All Manuals Search And Download.
41
I-Call (Motorola/EDACS)
I-Calls are direct unit-to-unit transmissions that are not heard by other system users. Your
UBC780XLT can receive these transmissions. How you receive I-Calls depends on whether
you are in Search or Scan mode.
During I-Call reception the display will show the Unit ID number of either the transmitting or
receiving mobile unit, not a talkgroup. Unit IDs will display differently according to the type of
trunked system, and will replace the 'n's shown here.
EDACS and MOTOROLA TYPE 1
MOTOROLA TYPE 2
innnnn
7nnnnnn
Hint -- There are thousands of Unit IDs in typical systems, but relatively few I-Calls at a
given moment, so it is normally best to let the scanner to receive any I-Call without trying to
specify particular units.
I-CALLS IN SEARCH MODE
In SEARCH mode, the scanner default is that I-Call reception is OFF. This means that
I-Calls will not be received until you program them to be ON. You have three choices for
controlling I-Call reception. Through the Menu system, go to TRUNK DATA / BANK NO /
I-CALL , and make your selection. The menu choices are:
I-CALLs
TALKGROUPS
1
2
OFF Not received Received normally This is the UBC780XLT default
ON
YES
Received normally Use this choice to receive I-Calls
together with normal
talkgroup traffic.
3
ONLY YES
NOT RECEIVED
Use this setting to listen to
I-Calls, and block all talkgroup
reception. For quick access to
this mode, press
then SRCH.
In I-Call ONLY mode, the display will show I-CALL, to warn that only I-Calls will
be received.
You can HOLD any I-Call ID. Because you can only hold on one ID, and there are two IDs
involved in any I-Call communication (the transmitting and the receiving units), you might not
hear the full conversation, but you probably will.
▲
In SEARCH mode, when you hear an interesting I-Call, you can enter the instant
shortcut then SRCH to enter I-Call ONLY mode. This blocks all talkgroup traffic
and lets you hear just the I-Call. To return to normal reception, you must use the
Menu system to select the ON or OFF option.
Note: When storing I-Call IDs, remember that the ID will be for only one of the units -- either
the transmitting or receiving unit. Unless you specifically want to receive a certain ID,
it might be better to use the special code in the HINT below.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
I-CALLS IN SCAN AND MANUAL MODE
You can store I-Call IDs in scanlists, just like talkgroup IDs, for use by ID Scan and Manual
modes. To program a specific I-Call Unit ID into a scanlist:
EDACS or Motorola Type 1
Enter
followed by the Unit ID digits, then E.
Motorola Type 2
Enter 7 followed by the Unit ID digits, then E.
HINT - There is a special code to let you receive all I-Call IDs with a single scanlist entry.
Simply enter
, 0, E. This will store the special code i0in an EDACS scanlist, or
700000in a Motorola scanlist. Then, whenever you SCAN this entry, or select it in
MANUAL, the scanner will receive any active I-Calls, regardless of the Unit IDs.
Note: Motorola I-CALL tracking performance may vary between systems.
Multi-Track
The UBC780XLT allows you to track more than one system at a time. Here are some
highlights of this feature:
▲
▲
▲
You can actually track up to 10 trunking systems at one time.
You can trunk scan or search and scan conventional frequencies at the same time.
You can program conventional frequencies in the same bank as trunking systems.
After the scanner finishes checking a trunked system for activity, it will conventionally
scan the other frequencies in the bank (remember, only trunking frequencies are
programmed in TRUNK mode).
To scan a mix of trunking and conventional banks, select the banks you wish to be active
with trunking off, then press TRUNK. The scanner will instantly begin scanning. If you have
not programmed a trunking bank with talkgroup ID’s, you will receive NO ID (----)
message for that bank. You can switch to SEARCH mode and the scanner will search for
any active ID’s on the system.
Multi-Track Operational Details
When more than one trunk system is active (for example two or more trunked systems or a
trunked system and one or more conventional frequencies), the radio jumps between
systems/frequencies as follows:
TRUNK SCAN: The scanner moves to a trunked system and looks for IDs in your Scan
List(s) for up to one second. If it finds no activity on your programmed talkgroups, it moves
on to conventional channels in the same bank or to the next active bank.
If the scanner finds that a talkgroup in one of your active Scan Lists is on the air, you will
begin to hear that communication and the scanner will of course display the proper
talkgroup number and any alpha tag. When the communication ends, the scanner will wait
for any delay period (such as a default of two seconds) for any further replies and, if none,
the scanner will move to the conventional channels in the same bank or to the next bank.
The scanner will not look for any other IDs within the same trunked system (as this would
slow the scan process). Note that if you press SCAN while you are listening to one ID, the
scanner will check to see if another ID in your Scan List is active. It will disregard the ID to
which you were just monitoring.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
TRUNK SEARCH: This mode works similarly to TRUNK SCAN. If the scanner finds any
(non-locked-out) ID when it checks the control channel, you will hear it. You will then hear
any replies that follow within two seconds (or whatever delay you may have set). After that
the scanner will move on and not continuously search the system for additional IDs (on
busy systems you would never leave the system if this were the case). Note that if you
press the SRCH key while monitoring one ID, the radio will check if any other IDs are
active (it will disregard the ID you just left), and if none are active, it will move on.
LIMIT/ ▲ KEY: If you wish to exit a trunked system without waiting for the currently active
talkgroup to finish its communication, press the LIMIT/▲ key. This is particularly helpful on
very busy systems where many talkgroups are active and activity is frequent and long-
lasting. Pressing this key will move the scanner on to the conventional frequencies in the
same bank or the next bank.
SCAN & SEARCH Icons
For the first time on a Uniden scanner, you will see both the SCAN and the SEARCH
icons active at the same time. This indicates that the radio is scanning conventional banks
and Trunk searching trunking banks. When the radio is trunking, only the SEARCH icon
will be lit. Note that to start a conventional search, you must place the radio into
conventional manual mode and then press the SEARCH key.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
®
EDACS Reception
EDACS® Tracking
TrunkTracker III now allows tracking of EDACS® trunked systems. Until now these widely
used systems have been almost impossible to monitor with a conventional scanner. With
your TrunkTracker III listening to EDACS(s) is remarkably easy, and perhaps even easier
than conventional scanning.
EDACS systems use 'Transmission Trunking', which means that each transmission is
assigned a new frequency. As the conversation moves through the system's frequencies,
your TrunkTracker II automatically follows it.
This chart shows a 30 second sample of EDACS transmissions. Eight different talkgroups
are using the system as their transmissions switch between the thirteen system frequencies.
Notice how the dotted line shows talkgroup 02-023 moving from channel to channel. Your
UBC780XLT can clearly and automatically follow this talkgroup, or any other, as you select.
EDACS systems are organised in a logical way that keeps related talkgroups together. Your
scanner is designed to take maximum advantage of this organisation to make your scanning
easy. It lets you zero in on just the part of the system you want to hear, whether it is an
individual channel or an entire department or city.
Programming EDACS System Frequencies
When you program EDACS frequencies, it is critical that you store each one in the
CORRECT LOCATION. By the nature of EDACS systems this is necessary for tracking. This
often is not the frequency order, so you must be sure you have the right sequence.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
An EDACS® Trunked system
This chart shows how talkgroups are organised
within an EDACS system at the AGENCY level.
The individual talkgroups cannot be shown at this
scale because there are over 2000. However the
chart can show the 16 Agencies in this example.
The system is logical and easy to understand.
EDACS systems are typically arranged in an
outline structure.
The system users are given blocks of talkgroups.
Sizes vary but most large cities and other agencies
have blocks of 128 channels. Smaller cities have
only 64 or 32 channels.
In this example, the County Sheriff is agency 01.
The city of Sullivan is Agency 03. Adams Hill and
Matthew Junction share Agency 08.
Your scanner shows EDACS talkgroups in AFS
(Agency-Fleet-Subfleet) format. This helps you see,
at a glance, who you are monitoring. And with the
partial-entry feature you can easily include nearby,
related channels in the same Fleet or Agency. You
can just as easily exclude entire unwanted Fleets and
Agencies.
When in Search mode, with the system frequencies
programmed, and your scanner locked to the control
channel, you can select a desired city by keying in the
AGENCY part of the AFS talkgroup. For example, you
can select the entire city of Sullivan with 4 key
presses zero, three,
, SRCH.
When you hear an interesting talkgroup, capture it to
your scan list by pressing E during the transmission.
Or HOLD on it by pressing the HOLD key.
If you want to monitor the Sullivan Police Dispatch
channel (which is talk group 03-062), press zero,
three,
, zero, six, two, HOLD.
Your scanner can also work in DECIMAL format. This
talkgroup in decimal format is 434. But decimal format
does not give you any information about the system
hierarchy. For example Sullivan, in decimal, uses
channels from 384 to 511. This is not as easy to
remember as Agency 03. But decimal is useful if you
need to work from decimal talkgroup lists.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Special EDACS® Features
AFS Partial Entry Feature
AFS is Uniden's method of encoding EDACS talkgroups. AFS stands for 'Agency-Fleet-Subfleet'.
AFS talkgroups are used in all EDACS reception -- in ID SEARCH, ID LOCKOUT and ID
SCAN scanlists. The powerful AFS Partial Entry feature designed into the UBC780XLT lets
you use either a complete talkgroup code, or just the most significant part.
This feature lets you expand or narrow searching and
scanning to one of 4 levels. By entering only the desired
part of an AFS talkgroup, you can select 2048 talkgroups,
128 talkgroups, 8 talkgroups, or a single talkgroup. For
example, you could program every talkgroup in a police
department with just 4 key presses. You can use the AFS
Partial Entry feature anywhere that you need to specify EDACS talkgroup.
Your UBC780XLT can also enter or display EDACS talkgroups in decimal format (0-2047).
Press MENU - TRUNK DATA, and for banks selected as EDACS banks, select Item 8,
EDACS ID FORM and change it to Decimal. You can use this feature to translate decimal
talkgroups lists to the much more powerful AFS format.
Examples of how you might use AFS are shown above in the description of an EDACS
trunked system, and elsewhere in this manual. It is very easy to use. Be sure to become
familiar with AFS Partial Entry, and your scanning will become far more flexible and efficient.
Emergency Call Alert
Your UBC780XLT alerts you when an EDACS Emergency transmission occurs.
EDACS systems often provide users with an 'Emergency' button on their radios. Users in
trouble can alert the dispatcher and other units and get priority access to the radio system.
When a user activates Emergency mode your scanner will flash EMERGENCY during the
entire transmission. At the beginning of each transmission it will sound a distinctive
emergency alert tone three times.
Patch Tracking
The UBC780XLT can follow EDACS patched talkgroups.
EDACS systems sometimes bring several talkgroups together in a 'Patch'. A patch might be
used by a police agency at night to provide a single channel with a single dispatcher for a
wide area. A patch is created when a single, temporary talkgroup substitutes for the original
talkgroups. While the patch is running, which may be for hours or days, the original
talkgroups cease to be used. If you were monitoring one of these talkgroups, you might
think there was no traffic, but in fact the talkgroup was operating at the different
temporary number.
If a talkgroup in your Scan List is patched, your scanner will continue to receive it under its
new identity until the patch is ended. When a patch is being received, the radio will display
[PATCH ID], and will show the temporary common talkgroup plus all the included talkgroups
in a cycling display. The UBC780XLT is limited to following one patch.
The temporary talkgroups used for patches are usually found in AFS code 15-xxx, and
sometimes 00-xxx.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
®
LTR Reception
®
LTR Tracking
LTR® (Logic Trunked Radio) systems are trunking systems used primarily by business or
private communications service providers, such as taxicabs, delivery trucks, and repair
services. These systems encode all trunking information as digital subaudible data that
accompanies each transmission. Users on an LTR system are assigned to specific
talkgroups, which are identified by the radio as six digit numbers. These numbers are in the
form AHHUUU, where:
A= Area code (0 or 1)
H= Home repeater (01 through 20)
U= User ID (000 through 254)
When the scanner receives a transmission on a channel set to the LTR mode, it first
decodes the LTR data included with the transmission. In the ID Search mode, the scanner
stops on the transmission and displays the talkgroup ID on the display. In the ID Scan
mode, the scanner only stops on the transmission if the LTR data matches a talkgroup ID
that you have stored in the bank’s talkgroup ID list and have not locked out.
LTR systems are frequently programmed so that each radio has a unique ID code.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Motorola Reception
Motorola Tracking
There are really two types of Motorola trunking systems. These are usually referred to as
Type I and Type II systems. Type I only occurs on some 800 MHz systems. All VHF, UHF
and 900 MHz trunking systems use Type II.
One important distinction between these two systems is the amount of data transmitted by
each radio when its push-to-talk button (PTT) is pressed. Every radio in a trunked system is
assigned a unique ID so the central site computer can identify it when it’s used. Both Type I
and Type II systems place radios (or radio users) into groups, called talkgroups, and these
talkgroups are also assigned unique IDs. Some radios have access to only one talkgroup,
while others have access to many talkgroups. The talkgroup(s) each radio can access is
called the radio’s affiliation(s).
In a Type II system, when someone uses their radio, only the radio ID is transmitted when
PTT is pressed, whereas in a Type I system the radio ID and its current affiliation are both
transmitted when PTT is pressed.
Why the difference? Type II systems are slightly more advanced because the central
computer maintains a database which is used to determine each radio’s affiliation (s).
Changes to a Type II system are easier than Type I because the system manager only
needs to update the database instead of reprogramming individual radios.
Another difference between the systems is that Type I systems are arranged in a Fleet-
Subfleet hierarchy. For example, its possible for a city using a Type I system to designate 4
Fleets, each with 8 Subfleets. Their fleets might be the Police Department, the Fire
Department, Utilities, and Administration. The Police may decide to further divide their fleet
into subfleets such as Dispatch, Tactical Operations, Detectives, North, South, East and
West Side Patrols, and Supervisors. All the available police radios would then be assigned
to one of the police subfleets. Determining the exact Fleet-Subfleet hierarchy for a particular
area is referred to as Fleet Map Programming, which is discussed further in this manual.
The disadvantage of a Type I system is that when PTT is pressed, the brief burst of data
must contain the radio’s ID and its Fleet and Subfleet. This is three times the amount of data
a Type II system radio sends, and as a result Type I systems usually accommodate fewer
users than Type II systems.
Even though there are many Type II systems, Type I systems are still in use. There are also
Hybrid systems which are a combination of both Type I and Type II. Your scanner defaults to
monitor Type II systems, but its possible to select a Preprogrammed Fleet Map or create a
Custom Fleet Map for your area.
For VHF and UHF Type II trunking systems, you will need to know the base, spacing
frequencies and offset channels. See page 51 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Fleet Map Programming
If you have programmed a trunk tracking bank for Motorola type and press TRUNK to start
Multi-Track, you will see user IDs display on your screen. Since the UBC780XLT defaults to
Type II systems, all the IDs will appear as numbers. However, if you notice a mix of odd and
even user IDs, for example 6477, 2560, 6481, 6144, 1167, etc., then you are probably
monitoring either a Type I or Hybrid systems.
You may also notice that you are missing responses when you hold on an active ID. Unlike
Type II, Type I/Hybrid systems require a Fleet Map that sets specific Fleet-Subfleet
parameters. It is easy to select a Fleet Map for your scanner; what is not always easy is
selecting or programming a map that matches your particular area.
There are 16 preset Fleet Maps listed in the appendix that you can choose, and these are
usually a good place to start when setting up a Type I/Hybrid trunk tracking bank. If you
choose a preset map and still have difficulty following complete conversations, then you'll
have to program your own Fleet Map.
Selecting Preset Fleet Map
1. Select TYPE 1 for the Trunk Type. (Refer to “Selecting Trunking
System Type” on page 34.)
2. Select the map you want to program using ▲, ▲ or
VFO and then press E, SELECT or VFO.
For example, PRESET 16.
The scanner returns to the other programming items.
Note: You will now begin to see Type I Fleet-Subfleet IDs. For example, 100-12, 100-9,
000-12, 400-8, etc. See User Defined Fleet Maps in the Appendix for more
information about Type I IDs.
How do you know if the preset map is correct? You will have to listen to see if you're
following complete conversations. If not, you should try another preset map.
Programming a Fleet Map
You may want to read User Defined Fleet Maps in the Appendix before programming a Fleet
Map. It contains a detailed explanation of Scanner Fleet Map Programming, as well as a
table listing the Fleet Map Size Codes.
1. Select TYPE 1 for the Trunk Type. (Refer to “Selecting
Trunking System Type” on page 34.)
2. Select USER CUSTOM using ▲, ▲ or VFO and then
press E, SELECT or VFO.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
3. Select the size code for the first block using
▲, ▲, or VFO.
4. Press E, SELECT, or VFO.
The next available block displays.
5. Repeat step 3 and 4 until you have selected a size
code for each block.
For details about each size code, see Fleet Map Size
Codes in the Appendix.
Programming a Hybrid System
A Hybrid system is simply a Type I system with some blocks designated as Type II blocks.
To program a Hybrid system, follow the steps listed in Programming a Fleet Map in the
previous section. However, if you want a block to be Type II, select Size Code S-0.
When you begin searching a trunking bank with a Hybrid Fleet Map, you will see both types
of system IDs. That is, Type II IDs usually appear as an even number without a dash; Type I
IDs appear as a three or four digit number, followed by a hyphen, followed by a one or two
digit number.
Setting the Base, Spacing Frequencies and Offset Channel for Motorola
VHF/UHF Trunked Systems
To properly track Motorola VHF and UHF trunked systems you must enter what is known as
the base, the spacing frequencies and offset channels for each system.
To enter the base, spacing frequencies and offset channel: (You can set up to three sets of
these, but almost all systems only use one set).
1. Press MENU.
2. Select TRUNK DATA - BANK NO. - TRUNK TYPE (TYPE2 UHF or VHF) - BASE
CONFIG using ▲, ▲ or VFO and pressing E, SELECT or VFO.
3. Enter a new base frequency with the keypad.
Note: If using a tracking system that uses two (2) or more base
frequencies, always program the lowest frequency as
Base 1 followed by the next highest frequency as
Base 2 with the last or highest frequency as Base 3.
4. Press E.
The display changes for entering the spacing frequency.
5. Enter a new spacing frequency with the keypad.
Note: You can only enter within a range of 5-100 kHz,
and 5 or 7.5 or 12.5 kHz multiples.
6. Press E.
The display changes for entering the offset channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
7. Enter a new offset channel with the keypad.
Note: You can only input within a range of 380-759.
8. Press E.
The display changes for entering the next base frequency.
9. To exit from this mode, press MENU repeatedly.
Note: • If the system is not tracking properly, you may need to try a new base frequency or
offset channel or you may be missing frequencies from the system.
• You can set up to three base, spacing and offsets for Motorola VHF/UHF trunked systems.
10. The offset channel for the first set should be CH380 (just press E to confirm this as
the default).
11. After you have pressed E to confirm CH380, the display will change to allow you to set
the second (of a maximum of three) base/space/offset combinations. Since almost all
systems only use one set, press MENU to exit the programming mode and return
to scanning.
Toggling the Status Bit
On Type II trunking systems there is a method by which specialised types of
communications utilise unique talkgroup numbers. An emergency call will occur on a unique
talkgroup from its primary assignment, for example. Because the UBC780XLT defaults to
Status-Bit On mode, you never need to worry about missing these transmissions. If you
have programmed talkgroup 33264 into Scan List memory, for example, and there is an
emergency call within the group, you will hear it on 33264.
The only time you may wish to turn Status Bits off is if you're trying to figure out the proper
fleet map of a Type 1 trunking system. To turn Status Bits off, enter into the menu mode and
select TRUNK DATA - BANK NO. - STATUS BIT. (This feature does not apply to EDACS
and LTR operation within the scanner.) Then use HOLD/▲ or LIMIT/▲ to change the setting
(on to off) and press E to program your change.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Control Channel Only Mode
When this function is activated, trunking is performed using control channel data only. Voice
channel (also known as "working channel") frequencies do not have to be programmed into
memory. When using this feature, the scanner will display "CC" and channel activity
indicator bars will not operate. This feature only applies to Motorola 800 MHz and 900 MHz
systems.
To turn this function on, choose Motorola Type-2 800 MHz or 900 MHz or TYPE 1 by
selecting TRUNK DATA - BANK NO. - TRUNK TYPE. Then set to the desired control plan
by selecting TRUNK DATA - BANK NO. - CTRL CH ONLY.
You must choose one of 4 frequency plans before you begin to Control Channel Trunk. Note
that the default, Plan 1, is the most common. Read the description of the Plans below for
details on which may apply for you.
PLAN 1: Use Plan 1 if the last three digits of ALL the frequencies in use end in one of the
following three digits: 125, 375, 625, or 875 (example: 865.1125, 865.7375, 865.6625,
866.8875).
PLAN 2: If the last three digits of frequencies less than 870.0000 end in one of the
following three digits (125, 375, 625, or 875) AND if ANY other frequencies end in (000,
250, 500, or 750) use Plan 2.
PLAN 3: If the last three digits of ALL the frequencies in use end in one of the following
three digits (000, 250, 500, or 750) use Plan 3.
PLAN 4: If the last three digits of frequencies less than 866.0000 end in one of the
following three digits (000, 250, 500, or 750) AND if ANY other frequencies end in (125,
375, 625, or 875) use Plan 4.
Of course you will know the Control Channel frequency itself so that will help you determine
the proper Plan. If you try one plan and you receive errors (such as the scanner jumping to
channels that are obviously not part of the system), you should try an alternate Plan.
Note: You can assign a fleet map to Type 1 or Hybrid systems scanned in Control
Channel only mode by going into the menu. You can also program IDs, set delays,
alpha tags and all the other parameters for systems scanned in this mode. You can
then either search the system to find new IDs or you can program IDs into memory
and then scan them.
Note: The Control Channel Only feature is an extremely powerful tool. You can use it to
determine if systems you are familiar with may have added new frequencies or you
can use it to discover new systems by simply finding active control channels (using
Search) and then programming them for Control Channel operation only.
Remember that this feature only applies to Motorola 800 and 900 MHz systems,
that you do have to set the menu for the proper system type (800 Type 1 or Type II
or 900 MHz) and you do have to program the control channel frequency into
memory and press and hold the TRUNK key to identify the frequency as trunked.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Disconnect Tone Detect Option (End Code)
When this function is disabled, the radio looks for squelch before returning to the control
channel instead of waiting for the disconnect tone. Only in rare instances will you need to
adjust the default settings.
The condition to return to control channels depends on whether the signal is present or not.
To set this function on/off, enter TRUNK DATA - BANK NO. - END CODE.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
Remote Interface
You can communicate and program your UBC780XLT in numerous ways with peripheral
devices using the Remote Interface Cable port. This radio offers the following modes:
▲REMOTE (PC Control) MODE
Program and control your scanner remotely from a PC using third party software (see the
flyer included in the box).
▲CLONE MODE
Clone all the frequencies, trunking talkgroups, and fleet maps programmed into your
scanner to another UBC780XLT scanner.
Remote (PC Control) Mode
To connect Scanner to PC:
Plug the scanner end of the RS232C straight interface cable (not supplied) into the remote
port on the rear of your scanner.
Plug the other end of the cable (DB-9 serial connector) into a personal computers serial port.
A few PCs may require an adaptor, most will not. You may need a DB-9 to DB-25 null
modem adaptor, or gender changer adaptor, available at most computer stores. Of course,
make sure your PC is turned on.
To program your scanner:
You can program and control your scanner remotely from a PC using third party software.
After connecting the scanner to a PC, turn the radio on.
To use the Remote (PC Control) mode, you must purchase third party software and use as
directed. Make sure that your scanner is connected to the serial port of the PC using the
RS232C straight cable.
Start Remote Mode:
Press E key for 2 seconds. REMOTE mode is
selected. To distinguish from Normal operation
mode, “RMT” icon appears.
A unique feature of the UBC780XLT is that all the
front panel keys as well as the VFO on the radio
remain operational in remote mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
55
For information on purchasing third party software to program and control your UBC780XLT,
see the flyer included in the box with this radio.
PC Control Parameter
For your information:
Transfer speed : 2400/4800/9600/19200 bps (adjustable)
Start/Stop
: 1 bit, 1 bit
Data Length : 8 bit
Parity bit
Code
: None
: ASCII code
Flow Control : None
Return Code : Carriage Return only
Change Transfer Speed
To change transfer speed, enter into the menu mode.
1. Press MENU.
2. Press ▲ or ▲ to select SYSTEM DATA and then
press E.
3. Press ▲ or ▲ to select PC CONTROL and then
press E.
4. To change the transfer speed, press ▲ or ▲. Then press E.
Clone Mode
You will need to purchase an RS232C cable and a null modem adaptor. RS232C cables are
available as male to male or male to female. Even if the cable you buy already has the Male
to Male connectors, you will still have to have the null modem adaptor. Below you will see
the pin connections that are internal to a standard device. (These items are available at your
local electronics stores.)
To connect the scanner to scanner:
Plug the male end of the RS232C straight interface cables (not supplied) into the remote
port on the rear of one of the two scanners. Then connect the DB-9 to DB-9 null modem
adaptor to the cable. Then plug the the other side of the null modem adaptor to the other
scanner. (DB9 Gender changers are also available at your local electronics store.)
Null Modem Adaptor
Pin connections
Male
DB9
Female
DB9
4
3
1
2
3
4
2
6 & 1
5
4
8
7
5
6
7
8
9
Not used
Download from Www.Somanuals.com. All Manuals Search And Download.
56
You can clone all of the programming of one UBC780XLT into another, including
frequencies, talkgroup IDs, alpha tags, delay settings, etc. After connecting the two
scanners, turn the radios on. Prepare each scanner for clone mode as follows.
1. Press MENU.
2. Select SYSTEM DATA - CLONE using ▲, ▲ or VFO and pressing E, SELECT or VFO.
3. Determine the scanner that has the frequency data that you want to transfer. This one
must be set up as the “Master Unit”, and the other must be set as the “Slave Unit”.
4. On the scanner that is the “Master Unit”,
select MASTER, then press E.
5. On the scanner that is the “Slave Unit”,
select SLAVE, then press E.
6. Press the SCAN key on both scanners. The data transfer is started from the Master Unit
to the Slave Unit.
During the data transfer, both scanners show
the following displays.
When the data transfer is completed,
COMPLETEdisplays.
If the data transfer is not successful, the
following error message will appear.
Note: To clear ERROR, press
.
To exit the clone mode, press the menu key repeatedly.
Note: Once you have completed the cloning of the scanners, reset by turning the scanners
off and then on again. This is particularly important to know if you wish to clone
another scanner right away.
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Additional Features
The following additional features are designed for you to customise your scanner. Once
these features have been turned on or off, they will remain as they are set until you reset
them, even if you turn the scanner off and then on again.
Dimmer
To change brightness of the display:
1. Press MENU.
2. Press E to select SYSTEM DATA.
3. Press E to select DIMMER.
4. Select one from High-Medium-Off using ▲ or ▲ and then press E.
Enter Lock
You can lockout the keypad to prevent any accidental entry. To activate this feature:
1. Press MENU.
2. Press E to select SYSTEM DATA.
3. Press ▲▲to select ENTER LOCK then press E.
4. Set to ON using ▲▲or ▲ and then press E.
The
icon appears on the display when locked.
Key Beep Option
To choose beep sound on or off:
1. Press MENU.
2. Press E to select SYSTEM DATA.
3. Press ▲ to select KEY BEEP and then press E.
4. Set to ON or OFF using ▲ or ▲ and then press E.
Screen Mask
The trunk, frequency, receiving mode, and signal meter indications on the display are
masked when this feature is activated. (except while in Search mode) This feature reduces
the amount of displayed information.
1. Press MENU.
2. Press E to select SYSTEM DATA.
3. Press ▲▲to select SCREEN MASK and then press E.
4. Set to ON or OFF using ▲ or ▲ and then press E.
5. To quickly turn off the screen mask, press the VFO/SELECT control.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Reverse Mode
This key will allow the user to observe the reverse frequency of the repeater. While pressing
/RVRS, the standard pair frequency will be displayed. For a list of the standard pair
frequencies, refer to the table “Reverse List” in the Appendix. If the frequency that you have
chosen does not have an offset frequency, the second line will indicate the error and display
NO REVERSE. This feature does not work in the SVC Search mode.
Mute On/Off
To manually turn on the Mute function, press and hold MUTE for more than 1 second until the
MUTE ONis displayed. You will not hear any audio. This feature does not function in the
WX alert mode, because the audio is already muted. To turn it off, press MUTE again.
Record On/Off
It is possible for you to record every one of the 500 channels or every ID that you have
programmed. (up to 1000 IDs). Once you have determined the channels or talkgroups that
you want to record, you must mark them to be recorded. Through the menu system, set the
RECORD ON for each channel, ID, or talkgroup using the 2:CHANNEL DATA ,
3:TRUNK DATA, or 4:SEARCH EVENTmenu screens. The audio signal from the TAPE
OUT Jack on the rear of the scanner will be turned on for each one that was marked. When
this feature is set on, the “LINE” icon appears in the display.(Refer to page 9)
Channel Step Selection
You can set channel steps, 5 kHz - 100 kHz or Auto, in Manual mode or Chain search
mode. The default receive mode should be the proper mode setting in almost all cases. You
may wish to set some VHF channels for NFM mode, depending on any adjacent channel
interference problems. Note that WFM is typically only used for broadcast frequencies, such
as TV audio or FM radio.
See “STEPS” in Menu Description for details.
Receiving Mode Selection
You can also set the receiving mode, AM or FM etc., in Manual mode or Chain search mode.
See “MODE” in Menu Description for details.
Frequency and Channel Tuning with the VFO Control
The VFO knob can be used for changing frequencies or changing memory channels (for
conventional channels or talkgroup ID Scan Lists).
1. The default setting is Channel. The CHAN icon appears in the display in this setting. In
Manual mode, turn the VFO control to the right (to step up through channels) or to the
left (to step down through channels. If you are in Trunk Manual mode, you will step
through Scan List memory locations (whether the CHAN or the FREQ icon is active).
2. To change the default setting to Frequency, press the VFO/SELECT control in Manual mode.
The icon will change to FREQ. Now turn the VFO to the right to step up through frequencies
sequentially or to the left to step down through frequencies. To change the step, you will need
to go into the Channel Data Menu and adjust the step for the desired memory location.
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Care and Maintenance
General Use
• Turn the scanner off before disconnecting the power.
• Always write down the programmed frequencies in the event of memory loss.
• If memory is lost, simply reprogram each channel. The display shows 000.0000 in all
channels when there has been a memory loss.
• Always press each button firmly until you hear the entry tone for that key entry, unless you
have turned off the KEY BEEPin the menu system.
Location
• Do not use the scanner in high-moisture environments such as the kitchen or bathroom.
• Avoid placing the unit in direct sunlight or near heating elements or vents.
• If the scanner receives strong interference or electrical noise, move it or its antenna away
from the source of the noise. If possible, a higher elevation, may provide better reception.
Also try changing the height or angle of the antenna.
Cleaning
• Disconnect the power to the unit before cleaning.
• Clean the outside of the scanner with a mild detergent. To prevent scratches, do not use
abrasive cleaners or solvents. Be careful not to rub the LCD window.
• Do not use excessive amounts of water.
Repairs
• Do not attempt any repair. The scanner contains no user serviceable parts. Contact the
Uniden Customer Service Centre or take it to a qualified repair technician.
Birdies
• All radios can receive birdies (undesired signals). If your scanner stops during Scan mode
and no sound is heard, it may be receiving a birdie. Birdies are internally generated
signals inherent in the electronics of the receiver.
Press L/O to lockout the channel, and then press SCAN to resume scanning.
Download from Www.Somanuals.com. All Manuals Search And Download.
60
Troubleshooting
If your UBC780XLT is not performing properly, try the following steps.
Problem
Suggestion
Scanner won’t work.
1. Check the connections at both ends of the AC Adaptor.
2. Turn on the wall switch of your room. You could be
using an outlet controlled by the wall switch.
3. Move the AC Adaptor to another wall outlet.
Improper reception.
1. Check the antenna connection or move and reposition
the antenna.
2. Move the scanner.
3. You may be in a remote area which could require an
optional multi-band antenna. Check with your dealer or
local electronics store.
Scan won’t stop.
1. Adjust squelch threshold - refer to page 10, “Setting
the Squelch”.
2. Check the antenna connection.
3. Check to see if many of the channels are locked out.
If so, the scanner has less chance of finding an
active channel.
4. Review each channels frequency to see if it is still
stored in memory and is correct.
5. Its possible that none of the programmed frequencies
are currently active.
Scan won’t start.
1. Press the SCAN key again.
2. Adjust the SQUELCH control.
3. Check to see if all channels are locked out.
Weather Scan won’t work. 1. Adjust squelch threshold - refer to page 10, “Setting
the Squelch”.
2. Check the antenna.
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Problem
Suggestion
tracked by
Scanner won’t track.
1. May not be a system which can be
your scanner. Make sure you press and hold TRUNK
for 2 seconds to enter into trunk mode.
2. Missing the data frequency.
3. Change to a Type 1 Scanner setup.
Review Fleet Map Programming on page 50.
Scanner won’t stop
1. No IDs have been programmed.
during Scan List mode.
2. The IDs you have stored are not active.
Scanner will not acquire 1. Adjust the squelch for trunking mode.
data channel.
See page 39.
2. Missing the frequency used for the data channel.
Check your frequency list.
Missing replies
1. Change to a Type 1 Scanner setup.
to conversations.
Review Fleet Map Programming on page 50.
2. Try another Preset Fleet Map or Program your own
Fleet Map.
3. Check to see that all of the systems frequencies
have been entered.
Channel Activity
Indicators are flashing
but no sound is heard.
1. May be a telephone interconnect call, which are
intentionally blocked by your scanner.
2. The ID in your display is not active.
Scanner not tracking
an EDACS system
properly.
1. Logical channel numbers (frequencies) for the system
are not programmed in the correct order.
Check frequency resources and reprogram.
2. Not all frequencies for the system are programmed.
Check frequency resources.
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Specifications
UBC780XLT is certified in accordance with AS/NZS 1053.
Channel:
500
Banks:
10 (50 channels each)
5 preprogrammed search bands
Service Bands:
Frequency Range:
25.0000 to 27.9950 MHz
28.0000 to 69.9900 MHz
70.0000 to 87.9875 MHz
88.0000 to 107.9000 MHz
108.0000 to 136.9875 MHz
137.0000 to 147.9950 MHz
148.0000 to 173.9875 MHz
174.0000 to 224.9000 MHz
225.0000 to 399.9500 MHz
400.0000 to 512.0000 MHz
806.0000 to 956.0000 MHz
CB/Marine CB etc
VHF Low Band
VHF Mid Band
FM Broadcast
Aircraft Band
2 Meter Amateur Band
VHF High Band
VHF TV
UHF Aircraft Band
UHF Band
800 MHz Band
1240.0000 to 1300.0000 MHz 25cm Amateur Band
Operating Temperature: -20 oC to +60 oC
Scan Rate:
100 channels per second (conventional mode)
Search Rate:
100 steps per second (Normal Search)
300 steps per second (Turbo Search)
Maximum 3.0W (2.3W normal @ 10% THD)
8 ohms (56 mm outer diameter)
AAD8500U AC Adaptor (13.8V DC, 700mA)
Telescopic Antenna (included)
Audio Output:
Internal Speaker
Power Requirements:
Antenna:
Antenna Jack:
External Jacks:
BNC type
External Speaker (EXT.SP.) (3.5 mm)
DC 13.8 V Power Jack, (centre is positive)
Remote Control (REMOTE) Jack (DB-9)
Tape Recorder Out (TAPE OUT) Jack (3.5 mm)
Size:
176.5mm (W) x 167mm (D) x 61mm (H)
1.33 kg
Weight:
Features and specifications are all subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Glossary of Terms
Glossary of terms
Alpha tag - This term refers to an alphanumeric text tag that you can enter to describe the
individual frequencies that you have programmed. Rather than having to associate a
specific frequency to the individuals that are using it, you can enter the actual name of the
group. This will eliminate the need for memorising the group’s frequency.
Attenuator - This scanner comes with a feature to attenuate or reduce the signal strength.
The built-in attenuator can be turned on specific frequencies to prevent strong signals from
overloading the scanner input, possibly damaging the scanner or missing other
transmissions due to the repeated stopping on the stronger signal.
Clone - This term identifies the ability to set up a duplicate scanner. This function allows
you to clone all the programming information, including frequencies, talkgroups and alpha
tags as well as bank settings and other parameters from one UBC780XLT to another.
Control Channel - A Control Channel is the frequency within a trunking system that runs
the system. On Control Channels (sometimes called Data Channels) you will hear a
buzzsaw sound. For the most part, it is the sound of the system’s central computer
directing talkgroups to particular voice (working) frequencies within the system.
CTCSS - Continuous Tone Controlled Squelch System- refers to a system where the radio
receivers are equipped with tone responsive devices which allow audio signals to appear
at the audio output, select voice processing such as scrambling or control repeater
functions only when a carrier modulated with a specific tone is received. This method may
be used to restrict access to the repeater or receiver, or reduce interference where several
stations with output frequencies in close proximity of each other make it difficult to hear the
conversation you are interested in. With CTCSS squelching, you can eliminate the
possibility of hearing unwanted conversations by selecting one of the 38 standard
subaudible tones. You will only hear those transmissions that have been programmed on
specific frequencies with the specific subaudible tone that you have selected.
DCS - (Digital Controlled Squelch) refers to a system where the radio receivers are
equipped with data burst responsive devices which allow audio signals to appear at the
audio output, select voice processing such as scrambling or control repeater functions only
when a carrier modulated with specific data burst is received. This method may be used to
restrict access to the repeater or receiver, or reduce interference where several stations
with output frequencies in close proximity of each other make it difficult to hear the
conversation you are interested in. With DCS squelching, you can eliminate the possibility
of hearing unwanted conversations by selecting one of the 104 standard data burst
subaudible tones. You will only hear those transmissions that have been programmed on
specific frequencies with the specific subaudible tone that you have selected.
Download from Www.Somanuals.com. All Manuals Search And Download.
64
Enter Lock - This is the term used for locking the keypad. This prevents accidental
re-programming of channels and talkgroups entered into memory. The default setting is off.
When ENTER LOCK is enabled, the following functions will be disable:
• Enter or modify the Channel frequency
• Enter or modify the Tone information
• Enter or modify the Trunking ID. ( this can be modified through the menu screen.)
I-Call - Most communications within a trunked system are group calls where one unit (such
as a dispatcher) communicates with all the units within her group (all the patrol vehicles on
the east side of town, for example). The units within this group comprise what is typically
known as a talkgroup. There are some communications which are direct unit-to-unit
conversations where one individual converses with another individual. The call is initiated
by a radio and is directed to another single radio. Within the system, no one outside of
these two users hears the conversation. This call is referred to as I-Call.
Key Beep - This is another term for the tone you hear as a keypad acknowledgement beep.
The default setting is on. If you have turned the Key Beep off, you now have a silent
keypad. You will not hear a tone each time you press a key.
PC Control - This term is associated with the ability to program frequencies and other
useful information via a computer by means of the Uniden national database or third party
software. You can change the transfer speed on the scanner needed to be compatible with
your PC. (See page 55)
Scan List - When you designate a bank to be a trunking bank, your scanner sets up 10
Scan Lists, which are simply list of your favourite IDs. Each list can contain up to 10 IDs,
so you can store a total of 100 IDs for each trunk bank. These lists are designed to help
you organise the trunking system users into categories.
Screen mask - Screen Mask reduces the amount of information that appears on the
display. Alpha tags that you have set for a channel along with a few function icons will
appear only on the display. This mode is particularly useful in public safety vehicles where
that are already overloaded with information. Screen Mask does not work in Search mode.
Status Bit - This term refers to Motorola Type II systems. There is a method by which
special types of communications utilise unique talk group numbers. For example, if all
emergency calls are set to occur on a specific talk group number then you will not miss
the transmission even if you have not programmed all the talk group numbers. With the
Status Bit on and you have programmed the unique number, then you don’t have to worry
what the rest of the groups numbers are. The topic of interest will be picked up.
Talkgroup - A group of users within a trunked system that communicate with one another.
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Appendix
Preset Fleet Maps
Preset Map 1
Preset Map 2
Block
Size Code
S11
Block
Size Code
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
S4
S4
S4
S4
S4
S4
S4
S4
S11
S11
S11
S11
S11
S11
S11
Preset Map 3
Preset Map 4
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
S4
S4
S4
S4
S4
S4
S12
--
0
1
2
3
4
5
6
7
S12
--
S4
S4
S4
S4
S4
S4
Preset Map 5
Preset Map 6
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
S4
S4
S12
--
S4
S4
S4
S4
0
1
2
3
4
5
6
7
S3
S10
S4
S4
S12
--
S12
--
Preset Map 7
Preset Map 8
Block
Size Code
S10
S10
S11
S4
Block
Size Code
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
S1
S1
S2
S2
S3
S3
S4
S4
S4
S4
S4
S4
Download from Www.Somanuals.com. All Manuals Search And Download.
66
Preset Map 9
Preset Map 10
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
S4
S4
S0
S0
S0
S0
S0
S0
0
1
2
3
4
5
6
7
S0
S0
S0
S0
S0
S0
S4
S4
Preset Map 11
Preset Map 12
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
S4
S0
S0
S0
S0
S0
S0
S0
0
1
2
3
4
5
6
7
S0
S0
S0
S0
S0
S0
S0
S4
Preset Map 13
Preset Map 14
Block
Size Code
Block
Size Code
0
1
2
3
4
5
6
7
S3
S3
S11
S4
S4
S0
S0
S0
0
1
2
3
4
5
6
7
S4
S3
S10
S4
S4
S4
S12
--
Preset Map 15
Preset Map 16
Block
Size Code
Block
Size Code
S3
0
1
2
3
4
5
6
7
S4
S4
S4
S11
S11
S0
S12
--
0
1
2
3
4
5
6
7
S10
S10
S11
S0
S0
S12
--
Download from Www.Somanuals.com. All Manuals Search And Download.
67
User Defined Fleet Maps
Type I Programming Information
When a Type I system is designed, the address information for all the IDs is divided into 8
equal sized blocks, numbered 07. When you program your scanner to track a Type I system,
you must select a size code for each of these blocks. When you have assigned a size code
to all 8 blocks, you'll have defined the Fleet Map for the system you're tracking. Each size
code determines the number of Fleets, Subfleets, and IDs each block will have. For
example, a size code of “4” has one Fleet, which is divided into 16 separate Subfleets, and it
has a total of 512 individual IDs.
When a block is assigned a size code, the Fleet or Fleets created within the block are
assigned a Type I ID. The way these IDs display on your scanner depend on the block
number and the blocks size code. When a Type I ID displays, the left most digit represents
the block which contains the ID. The next two or three digits identify which Fleet is active,
and the last digit(s) identifies the Subfleet.
405-12
Block
(1 digit)
Subfleet
(1 or 2 digits)
Which Fleet
within the Block
(2 or 3 digits)
The details concerning how the size codes are selected by a Type I System designer are
highly dependent on the specific needs of the systems users. Some organisations may want
many subfleets with only a few radios each, while another organisation may want only a few
subfleets with many radios each. Your task is to program your fleet map with the same size
code assignments as the trunked system. If you do this accurately, you'll track all the Fleet-
Subfleet combinations used by the system. In other words, you'll hear complete
communications while monitoring a trunked system.
If you don't already know the size codes used, you'll have to guess at them. But since you
don't have to figure out all the blocks at once, this isn't as hard as it seems. Select a size
code for a block, and then press SCAN. Now listen to the communications. If you decide you
are receiving most of the replies to the conversations with IDs assigned to the block you just
programmed, then you've probably selected the right size code and can work on the next
block of the map.
Finally, for most public safety systems there are some size codes which are more common.
SIZE CODE 3 and SIZE CODE 4 are probably the most common, followed by SIZE CODE
10, SIZE CODE 11, and SIZE CODE 12.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Fleet Map Size Codes
Blocks
Used
Size
Fleets
Subfleets
IDs
0
1
Reserves block for Type II IDs
+
1
1
1
1
1
1
1
1
1
1
1
2
4
8
128
16
8
4
8
16
64
2
3
8
128
512
32
4
1
16
4
5
64
32
32
16
8
6
8
32
7
4
64
8
4
128
256
256
256
1024
2048
4096
9
4
10
11
12
13
14
4
8
2
16
16
16
16
1
1
1
Size Code Restrictions
If you select size code 12, 13, or 14, there are some restrictions as to which blocks can be
used for these codes.
•
•
•
SIZE CODE 12 can only be assigned to Blocks 0, 2, 4, or 6.
SIZE CODE 13 can only be assigned to Blocks 0 and 4.
SIZE CODE 14 can only be assigned to Block 0.
Since these size codes require multiple blocks, you will be prompted for the next available
block when programming a Fleet Map. For example, if you assign Block 0 as an SIZE CODE
12, you will be prompted for Block 2, the next block available, instead of Block 1. And if you
assign Block 0 as an SIZE CODE 14, you would not see another prompt because it uses all
available blocks.
Download from Www.Somanuals.com. All Manuals Search And Download.
69
AUSTRALIAN REVERSE FREQUENCY LIST
Lower
Upper
Band Name
VHF Low band
VHF Low band
VHF Low band
VHF Low band
VHF Low band
VHF Low band
Mode
FM
FM
FM
FM
FM
FM
MULTI
MULTI
FM
Reverse
plus 2 MHz
Designation
31.0000
33.0000
35.0000
37.0000
44.0000
42.0000
53.5000
52.5000
70.2500
72.7500
77.5000
80.0000
85.0000
82.5000
146.6250
146.0250
147.0250
147.6250
149.2500
153.8500
150.0000
154.6000
162.0500
157.4500
165.2000
32.0000
34.0000
36.0000
38.0000
45.0000
43.0000
53.9750
52.9750
72.3000
74.8000
79.8125
82.3125
87.2000
84.7000
147.0000
146.4000
147.3500
147.9500
149.7625
154.3625
151.4000
156.0000
165.2000
160.6000
168.2000
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Trunked repeater
outputs
plus 2 MHz
minus 2 MHz
minus 1 MHz
plus 2.5 MHz
plus 2.5 MHz
minus 2.5 MHz
minus 600 kHz
plus 600 kHz
plus 4.6 MHz
plus 4.6 MHz
minus 4.6 MHz
plus 4.6 MHz
6 metre ham band
6 metre ham band
VHF Mid band (E)
VHF Mid band (E)
VHF Mid band (E)
VHF Mid band (E)
VHF Mid band (E)
VHF Mid band (E)
2 metre ham band
2 metre ham band
2 metre ham band
2 metre ham band
VHF High band (A)
VHF High band (A)
VHF High band (A)
VHF High band (A)
VHF High band (A)
VHF High band (A)
VHF High band (A)
FM
FM
FM
FM
FM
MULTI
MULTI
MULTI
MULTI
FM
FM
FM
FM
FM
FM
FM
169.8000
172.8000
VHF High band (A)
FM
Trunked repeater
inputs
412.4500
403.0000
438.0250
433.0250
460.0000
450.5000
470.0000
475.2000
472.2500
477.4500
485.2000
480.0000
490.0000
495.2000
500.0000
510.0000
865.0000
419.9875
410.5375
439.9750
434.9750
469.4500
459.9500
471.2000
476.4000
474.7750
479.9750
489.9875
484.7875
494.7750
499.9750
509.5250
519.5250
870.0000
UHF low band (T)
UHF low band (T)
70 cm ham band
70 cm ham band
UHF mid band (U)
UHF mid band (U)
UHF mid band (W)
UHF mid band (W)
UHF mid band (W)
UHF mid band (W)
UHF mid band (W)
UHF mid band (W)
UHF high band (W)
UHF high band (W)
UHF high band (W1)
UHF high band (W1)
800 MHz band
FM
FM
MULTI
MULTI
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
FM
minus 9.45 MHz
minus 5 MHz
minus 9.5 MHz
plus 5.2 MHz
plus 5.2 MHz
minus 5.2 MHz
plus 5.2 MHz
plus 10 MHz
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Repeater outputs
Repeater inputs
Trunked repeater
outputs
minus 45 MHz
820.0000
825.0000
800 MHz band
FM
Trunked repeater
inputs
Download from Www.Somanuals.com. All Manuals Search And Download.
70
CTCSS Frequency List (Hz)
DCS Tone Code
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
73
Memo
Download from Www.Somanuals.com. All Manuals Search And Download.
74
UBC780XLT SHORTCUTS
If you need any assistance with this product, please check out our website at
you with any matters regarding the operation of this unit, available accessories, or any other
related matters.
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts
NOTE: SMART SCAN NOT
APPLICABLE IN
AUSTRALIA
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT Flow Charts (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
UBC780XLT SHORTCUTS
This shortcut card is designed to assist you in getting through the menu
screens using the direct entry mode for commonly used features. Please read
the manual thoroughly before using this card. Be sure to back out of the
menu screen after each shortcut by repeatedly pressing MENU.
Download from Www.Somanuals.com. All Manuals Search And Download.
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
Warrantor:
Uniden Australia Pty Limited ACN 001 865 498
Uniden New Zealand Limited
ELEMENT OF WARRANTY: Uniden warrants to the original retail owner for the duration of this warranty, its UBC780XLT
(herein after referred to as the Product), to be free from defects in materials and craftsmanship with only the limitations or
exclusions set out below.
WARRANTY DURATION: This warranty to the original retail owner only, shall terminate and be of no further effect 12 months
after the date of original retail sale. This warranty will be deemed invalid if the product is; (A) Damaged or not maintained as
reasonable and necessary, (B) Modified, altered or used as part of any conversion kits, subassemblies, or any configurations not
sold by Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorised Uniden Repair Agent for a defect or
malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not
manufactured by Uniden.
PARTS COVERED: This warranty covers for one (1) year, the Base Unit. All accessories, AC Adaptor, Cigarette Lighter Adaptor Cord,
Antenna & Mounting Bracket are covered for 90 days only.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is
in effect, the warrantor at its discretion, will repair the defect or replace the product and return it to you without charge for parts
or service. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. THIS GUARANTEE IS IN ADDITION TO AND DOES NOT IN ANY WAY AFFECT YOUR RIGHTS
UNDER THE CONSUMER GUARANTEE ACT.
WARRANTY CARD: If a warranty card has been included with this product then please fill it in and return to us within 14 days
of purchase. Your name and the Serial number of the product will then be registered in our database and this will help us process
your claim with greater speed and efficiency should you require warranty service.
PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY: In the event that the product does not conform to this
warranty, the Product should be shipped or delivered, freight pre-paid, with evidence of original purchase (eg. a copy of the sales
docket), to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED
SERVICE DIVISION
345 Princes Highway,
UNIDEN NEW ZEALAND LIMITED
SERVICE DIVISION
150 Harris Road,
Rockdale NSW 2216
East Tamaki, Auckland
Customers in other States should ship or deliver the Product freight pre-paid to their nearest Uniden Authorised Repair Centre
(Contact Uniden for the nearest Warranty Agent to you).
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 Uniden Australia Pty. Ltd.
Uniden New Zealand Ltd.
All rights reserved.
Printed in the Philippines.
UBZZ01305AZ
Download from Www.Somanuals.com. All Manuals Search And Download.
|