DECT2185 Series User's Guide
What's in the box?
Base AC adapter
(PS-0034)
Battery
cover
DECT2185 base with
answering system and
cordless handset
Telephone
cord
Rechargeable
battery pack
(BT-1016)
You might also find:
DCX210
If you purchased You should
Charger AC
adapter
accessory
handset &
charger
model number:
DECT2185
have:
None
(PS-0035)
DECT2185-2
DECT2185-3
DECT2185-4
DECT2185-5
DECT2185-6
1 of each
2 of each
3 of each
4 of each
5 of each
Battery
cover
Rechargeable
battery pack
(BT-1016)
If any items are missing or damaged, contact our Customer Care
Line immediately. Never use damaged products!
If You...
Contact Uniden’s...
Phone Number
817-858-2929 or
800-297-1023
have a question or problem
Customer Care Line*
need a replacement part or
an accessory (such as a wall
mount bracket)
Parts Department*
800-554-3988
need special assistance due
to a disability
800-874-9314
(voice or TTY)
Accessibility Help Line
* During regular business hours, Central Standard Time. Visit our website for detailed business hours.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Your Phone
Charge the Battery
1) Unpack all handsets, battery packs, and
battery covers. If any battery cover is
already on the handset, press in on the
notch and slide the cover down and off.
2) Line up the red and black wires
on the battery pack with the
label inside the handset.
Black
Red
3) Push the connector in until it
clicks into place; tug gently
on the wires to make sure
the battery pack is securely
connected.
4) Place the cover over the battery
compartment and slide it up into place.
5) Connect the base AC adapter to the AC IN
7.8V jack on the rear of the base. Route
the cord through the molded wiring
channel as shown.
6) If you have accessory
handsets, connect a
charger AC adapter
to each charger's AC
IN 8V jack and set the
plug into the notch as
shown. (These
adapters might
already be
connected.)
7) Plug the other end of each adapter into
a standard 120V AC power outlet.
V
8
N
I
C
A
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
8) Place a handset in the base and any accessory handset(s) in the
charger(s) with the display(s) facing forward. The
ChArGE light on the base and each charger
should all turn on.
If...
Try...
the ChArGE
light does
not turn on
-
-
-
reseating the handset.
checking the AC adapter connection.
seeing if the outlet is controlled by a
wall switch.
Charge all handsets completely (about 15
hours) before using them.
Connect the Telephone Cord
Use the telephone cord to
connect the TEL LINE jack to a
standard telephone wall jack.
Test the connection
1) Pick up the handset from
the cradle and press
TaLk
. You should hear a
dial tone, and the display
should say Talk
.
If...
Try...
you don't hear a dial tone or the checking the connection between
display says Check Tel Line
the base and the phone jack.
ENd
2) Make a quick test call. (Press
to hang up.)
If...
Try...
you keep hearing a dial tone changing the dial mode (see page 25).
see page 24 for tips on avoiding
interference.
there's a lot of noise or static
3) Test any accessory handsets the same way. If you can't get a
dial tone or the handset display says Unavailable, try moving the
handset closer to the base or resetting it (see page 25). Charge
all handsets completely (about 15 hours) before using them.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know Your Phone
Parts of the Base
If the key name is spelled out on the key itself, it's not labeled in the
drawing below.
PHONEBOOK/LEFT
PLAY/STOP
Display
Speaker
UP
CALLER ID/RIGHT
DOWN
DO NOT DISTURB
DELETE
FIND HANDSET/
INTERCOM
SPEAKER
Charging
contacts
Twelve-key
dial pad
Microphone
(on back)
Base keys and how they work
Key name
What it does
(and icon)
-
-
-
While this station is ringing: mute the ringer for this call only.
During a call: mute the microphone.
While entering text: delete one character, or press & hold to
delete all the characters.
CLEAr/MUTE
-
-
In standby: open the menu.
In the menu or any list: select the highlighted item.
MENU/SELECT
rEDIAL/PAUSE
PLAY/STOP
-
-
In standby: open the redial list.
While entering a phone number: insert a 2-second pause.
-
-
-
In standby: start playing messages.
While a message is playing: stop playing messages.
In the menu or a list: exit the menu completely.
(
)
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Key name
(and icon)
What it does
-
-
In standby or during a call: open the phonebook.
In any menu or list: go up one level. (If you are already at
the top level, the phone exits the menu and returns to the
previous operation.)
During text entry: move the cursor to the left.
While playing messages: for the first 2 seconds, go to the
previous message; after that: go to the start of this message.
PhONEBOOK/
LEFT
(
/
)
-
-
CALLEr ID/
rIGhT
-
-
-
In standby or during a call: open the Caller ID list.
During text entry: move the cursor to the right.
While a message is playing: skip to the next message.
(
/
)
-
-
In standby: increase the ringer volume.
During a speakerphone call or while a message is playing:
increase the speaker volume.
UP (
)
-
In the menu or any list: move the cursor up one line.
-
-
In standby: decrease the ringer volume.
During a speakerphone call or while a message is playing:
decrease the speaker volume.
DOWN (
ON/OFF
)
-
-
In the menu or any list: move the cursor down one line.
In standby: turn the answering system on or off.
-
-
While a message is playing: delete this message.
In standby: delete all messages.
DELETE (
)
DO NOT
DISTUrB (
-
In standby: turn the Do Not Disturb feature on or off (see
)
FLASh
-
-
During a call: switch to a waiting call.
While the phone is ringing: add the incoming caller ID to the
call block list (block the call).
BLOCK
FIND hANDSET/
INTErCOM
-
-
In standby: page a handset using the intercom.
During a call: put the call on hold & start a call transfer.
SPEAKEr
-
-
In standby: start a speakerphone call (get a dial tone).
During a speakerphone call: hang up.
(
)
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR/
UP
Parts of the handset
If the key name is spelled out
on the key itself, it's not
labeled in the drawing to the
right.
INTERCOM
CALLER ID/
RIGHT
PHONEBOOK/
LEFT
DOWN
SPEAKER
Twelve-
key dial
pad
REDIAL/
PAUSE
MESSAGES/
MUTE
Charging
contacts
Microphone
Handset keys and how
they work
Key name
What it does
(and icon)
-
-
-
In standby: increase the ringer volume.
During a call: increase the call volume.
In the menu or any list: move the cursor up one line.
UP (
)
CALLEr ID/
-
-
In standby or during a call: open the Caller ID list.
During text entry: move the cursor to the right.
rIGhT (
)
-
-
-
In standby: decrease the ringer volume.
During a call: decrease the call volume.
In the menu or any list: move the cursor down one line.
DOWN (
)
-
-
In standby: open the menu.
In the menu or any list: select the highlighted item.
During a call: hang up.
In the menu or any list: exit & go to standby.
MENU/SELECT
END
-
-
-
-
-
In standby: page another station using the intercom.
During a call: put the call on hold & start a call transfer.
While entering text: delete one character, or press & hold to
delete all the characters.
CLEAr/
INTErCOM
-
-
-
In standby or during a call: open the phonebook.
In the menu: go back to the previous screen.
During text entry: move the cursor to the left.
PhONEBOOK/
LEFT (
)
-
-
In standby: start a telephone call (get a dial tone).
During a call: switch to a waiting call.
TALK/FLASh
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Key name
(and icon)
What it does
SPEAKEr (
)
-
Switch a normal call to the speakerphone (& back).
rEDIAL/PAUSE
-
-
In standby: open the redial list.
While entering a phone number: insert a 2-second pause.
(
)
-
While the phone is ringing: add the incoming Caller ID
information to the call block list (block the call).
BLOCK
-
-
-
In standby: access your answering system.
During a call: mute the microphone.
While the phone is ringing: mute the ringer for this call only.
MESSAGES/
MUTE (
)
reading the Displays
On the base
On the handset
Status icons
Time
Answer ON
Status
Answering
icons
system status
12:00A
Handset #1
Day and
Message
counter
time
SUN 12:00 AM
Handset
banner
Caller ID
Caller ID
New CID: 5
count
count
The table below shows the possible icons and what they mean. Since
the icons appear based on what you're doing with the phone, you
won't ever see all of these icons at the same time.
Icon
What it means
The ringer is turned off: this station will not ring when a call
comes in.
You have a voice message waiting (see the section titled
"Using Voice Message Notification" on page 15).
Privacy Mode is on: no other station can join your call.
The speakerphone is on.
The microphone is muted, & the caller can't hear you.
(Handset only) T-coil mode is on. (See "Do you use a T-coil
hearing aid?" on page 24.)
(Handset only) The battery is 1) fully charged, 2) half charged,
3) getting low, or 4) empty.
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
The menus are designed to be as easy as possible. Some users don't
even need the manual once they know how to perform these actions:
MENU/SELECT
Open the menu Press
.
The arrow cursor on the left side of the line shows which
UP
Move the cursor menu item is currently highlighted. Use
to move the
DOWN
cursor up &
to move it down.
MENU/
Move the cursor to highlight the option, then press
Select an option
Go up one screen Press
SELECT
.
PhONEBOOK/LEFT
.
END
PLAY/STOP
.
On the handset, press
(If you open the menu during a call, use
back out of the menu without hanging up.)
; on the base, press
Close the menu
PhONEBOOK/LEFT
to
If you don't press any
keys for thirty
seconds, the
To open the menu,
press MENU/SELECT.
To select the
highlighted
option, press
MENU/SELECT.
phone times out
and exits the
menu. (When
setting the day
and time, the time-
out period is
extended to two
minutes.)
Handset Setup
Ans. Setup
Use UP and
OR
DOWN to move
the cursor.
Day & Time
To close the menu,
press END on the
handset or PLAY/
STOP on the base.
Global Setup
Using the Base Menu
You have the following options from the base:
Reset the voice message waiting indicator to bring it back
into sync with your voice mail service (see page 15).
VMWI Reset
Call Blocking
Block unwanted calls from up to 20 phone numbers and
manage your call block list (see page 14).
Base Language Change the display language.
Register additional handsets to the base or re-register
a handset that you had to reset for some reason (see
"Resetting and Registering Handsets" on page 25).
Register
Handset
ꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the handset Menus
Handset Setup
You can change these settings separately for each handset.
Turn on T-coil mode to reduce noise on some hearing
T-coil
aids (see "Do you use a T-coil hearing aid?" on page 24).
Choose one of four melodies or three tones for the
handset's main ring tone. As you highlight each ring
Ringer Tones
tone, the phone plays a sample of the tone. When you
MENU/SELECT
hear the tone you want, press
.
Turn on the personal ring feature. If you have Caller ID,
this feature lets you assign special ring tones to anyone
in your phonebook: this handset will use the special
ring tone when that person calls.
Personal Ring
Autotalk
Turn on Auto Talk so you can answer the phone just by
picking up the handset from the cradle (without having
to press any buttons).
Turn on Any Key Answer so you can answer the phone
by pressing a key on the twelve-key dial pad.
Any Key Answer
Banner
Change the name used on the handset's display.
Handset Language Change the display language.
Key Touch Tone
Have the keypad sound a tone when you press a key.
Ans. Setup
This menu controls the options and settings for your answering
system (see "Ans. Setup menu options" on page 18).
Day & Time
You need to set the day & time so messages get the right time stamp.
Up
doWN
MENU/sELECT
to choose the day of the week; press .
1) Use
&
2) Use the number keypad to enter the hour and minutes.
Up
doWN
MENU/sELECT
to select AM or PM; press .
3) Use
&
Global Setup
The settings on this menu apply to all handsets and the base. Before
changing these settings, make sure the phone is in standby and all
handsets are within range of the base. (Only one handset at a time
can change these settings.)
ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your area code so the phone hides the area code on
Area Code
Dial Mode
incoming local calls (see "Using Seven-digit Dialing" on page 12).
Change the way your phone communicates with the telephone
network (see "Changing from Tone to Pulse Dialing" on page 25).
Set Line
Mode
Do not change this setting unless instructed to by customer
service.
Call Blocking
This menu lets you block unwanted calls from up to 20 phone
numbers and manage your call block list (see page 14).
Entering Text on Your Phone
When you want to enter text into your phone (for example, a name
in the phonebook), use the twelve-key dial pad to enter the letters
printed on the number keys. Here's how it works:
The phone enters the letters in the order they appear on the key.
2
For example, if you press the number key once, the phone
2
enters the letter
A
. Press twice for
B
, and three times for
C.
If you press the key again after the last letter, the phone starts the
same letter sequence with small letters. If you press four times
2
2
in a row, the phone enters
and six times for
a
(small letter). Press five times for
b,
c
.
If you see the icon [Aa] in the display, the phone enters capital
letters first (A B C), then small letters (a b c), then the number on
the key ( ). The icon [aA] means the phone starts at the small
2
letters, so it enters small letters first, then the number on the key,
then capital letters.
The phone automatically uses a capital letter for the first letter and
any letter right after a space; all other times, it uses small letters.
If two letters in a row use the same number key, enter the first
CaLLEr Id/rIGHT
letter, then use
to move the cursor to the next
position to enter the second letter.
To
Follow these steps
Switch between capital
& small letters
Press
.
PhONEBOOK/LEFT
CALLEr ID/rIGhT
Press
to move the cursor to the left
to move the cursor to the right.
Move the cursor
or
#
.
Leave a blank space
Press
ꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Follow these steps
Move the cursor to the letter you want to erase and
CLEAr CLEAr/INTErCOM
CLEAr/
Erase one letter
press
(
on the handset;
MUTE
on the base).
CLEAr
Erase the entire entry Press & hold
Enter punctuation or a
.
0
Press to rotate through the available symbols.
symbol
Using Your Phone
From a handset From the base
From a handset
To...
speakerphone
speakerphone
make a call: Dial
the number, then
TALK/FLASh
SPEAKEr
SPEAKEr
SPEAKEr
SPEAKEr
Press
. Press
.
Press
Press
Press
.
.
.
TALK/FLASh
SPEAKEr
answer a call
Press
Press
. Press
.
END
or put the handset in the
hang up
cradle.
switch between the
speaker & earpiece
SPEAKEr
SPEAKEr
.
Press
.
Press
NA
MESSAGES/MUTE
Press again to turn the microphone back on.
CLEAr/MUTE
.
mute the micro-
phone during a call
Press
.
Press
FIND hANDSET/
Press
CLEAr/INTErCOM
Press
.
INTErCOM
.
put a call on hold
If the call is on hold for 5 minutes, it will be disconnected.
return to a call on
hold
TALK/FLASh
SPEAKEr
SPEAKEr
.
Press
. Press
.
Press
While the phone is
mute the ringer for While the phone is ringing, press
CLEAr/
ringing, press
MESSAGES/MUTE
this call only
.
MUTE
.
Changing the Volume
You can set the volume of the ringer and speaker separately for the
base and each handset; you can also set the earpiece volume on
Up
doWN
each handset. For each item, press
to make it louder or
to
make it softer. The available volume levels and how change them are
listed below:
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Change the When
On the base
On a handset
ringer
volume
the phone is in
standby
select Off, Low,
select Off, Low,
Medium, or High Medium, or High
earpiece
volume
you are on a normal
call
choose one of 6
volume levels
NA
you use the speaker-
phone for a call or
getting messages
speaker
volume
choose one of 10
volume levels
choose one of 6
volume levels
Using the redial List
The phone saves the last 5 numbers you dial on each station. To
rEdIaL/paUsE
Up
doWN
and to scroll
open the redial list, press
; use
pHoNEbook/LEfT
through the list. To close the list, press
. With the
phone in standby, open the list and find the number you want. Then:
TALK/FLASh
SPEAKEr;
or
On the handset, press
on the base, press
to redial the selected number
to delete the number
SPEAKEr
.
MENU/SELECT
Press
& select Delete Entry
.
MENU/SELECT
to save it to the phonebook Press
& select Store Into Pb
.
Using Caller ID and Call Waiting
You have to subscribe to Caller Id, Call Waiting, and Caller Id
on Call Waiting services to use the features described in this
section: contact your telephone provider for more information.
When a call comes in, the phone displays the caller’s number and
name (if available). The phone saves the information for the last 30
received calls to the CID list. When it's in standby, the phone displays
how many calls came in since the last time you checked the CID list.
CALLEr ID/rIGhT
Open the CID list
Press
.
DOWN
oldest. Press
Scroll through the CID Press
to scroll through the list from newest to
UP
to scroll from oldest to newest.
list
PhONEBOOK/LEFT
.
Close the CID list
Press
Dialing from the Caller ID list
1) Find the entry you want to dial.
2) If the number is a toll or long distance call, but there's no 1 at the
front of the CID record, press to add the 1.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
TaLk/fLasH
spEakEr
to dial the number;
3) On the handset, press
on the base, press
or
spEakEr
.
TaLk/fLasH
spEakEr
before you open the CID
(You can also press
or
MENU/sELECT
list. Find the number you want to dial, then press
.)
Caller ID menu options
Open the CID list with the phone in standby. Find the number you
MENU/sELECT
want and press
. Choose one of these CID menu options:
Delete Entry
Erase this Caller ID number.
Add this number to this station's phonebook. The phone
prompts you to enter a name & edit the number; handsets
also prompt you to choose a personal ring.
Store Into Pb
Erase this station's CID list. (This does not affect the CID
lists saved on any other stations.)
Delete All
(Handset only) Add the number to the call block list (see
Add Call Block
Using Call Waiting
If you get a Call Waiting call, the phone sounds a tone and displays
fLasH TaLk/
any CID information received for the waiting call. Press
(
fLasH
on a handset) to switch between the current call and the waiting
call; remember, each time you switch, there is a short pause before
you're connected to the other caller.
Using Seven-Digit Dialing
If you can make a local call by dialing only seven digits instead of ten,
you can tell the phone to hide your local area code in the CID list.
do not enter an area code if your phone company requires ten-
digit dialing. You might not be able to dial from the CId list.
1) From any handset, open the menu with the phone in standby.
2) Select Global Setup, then select Area Code
.
0 - 9
3) Use the number keypad ( ) to enter your three-digit area code.
MENU/sELECT
4) Press
when you’re finished.
The phone uses the programmed code as a filter. When calls
come in, the phone compares the area code to the programmed
one. If they match, the phone hides the area code in the CID list.
#
While reviewing the list, press to toggle the area code off & on.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Phonebook
Each station can store up to 70 entries in its phonebook.
PhONEBOOK.
Open/close the phonebook Press
DOWN
from A to Z or
Press
to scroll through the phonebook
Scroll through the entries
UP
to scroll from Z to A.
Jump to entries that start
with a certain letter
Press the number key corresponding to the
letter you want to jump to.
1. Find the entry you want to dial.
Dial an entry
TALK/FLASh
or
2. On the handset, press
SPEAKEr
SPEAKEr
.
; on the base, press
Phonebook menu options
Open the phonebook with the phone in standby, then press
MENU/
sELECT
to open the phonebook menu. Choose one of these options:
Add an entry to your phonebook. The phone prompts you to enter
the name & phone number. (Handsets will also prompt you to
choose a personal ring.)
Create
New
Copy All Copy the whole phonebook to another station.
Delete
All
Erase all the entries in this station's phonebook. (This does not
affect the entries saved on any other stations.)
Phonebook entry options
With the phone in standby, open the phonebook and find the entry
MENU/sELECT
you want. Press
to open the individual phonebook entry
menu. Choose one of these options:
Edit this entry. The phone prompts you to enter the name & phone
number. (Handsets will also prompt you to choose a personal ring.)
Edit
Copy
Copy this entry to another station.
Delete Erase this entry.
Chain Dialing
If you often have to enter a series of digits or a code number
during a call, you can save that code number to a phonebook
entry and use the phonebook to send the code number.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the code number (up to 20 digits) into the phonebook just
like a regular phonebook entry. Be sure to enter the code number
into the phonebook exactly as you would enter it during a call.
When you hear the prompt that tells you to enter the number, open
the phonebook and find the entry that contains your code number.
MENU/sELECT
Press
mind, use
to transmit the code. Or, if you change your
pHoNEbook/LEfT
to close the phonebook.
Finding a Lost handset
With the phone in standby, press
fINd HaNdsET/INTErCoM
on the base.
Select the handset you want to find (or All to page all handsets). The
fINd HaNdsET/
paged handset(s) beep for 1 minute or until you press
INTErCoM
TaLk/fLasH
ENd
again or press
followed by on the handset.
Using Special Features
Using Do Not Disturb
The Do Not Disturb or DND feature turns off the ringers of the
base and all handsets at the same time.
do NoT dIsTUrb
With the phone in standby, press and hold
on the
base. The phone automatically turns on the answering system and
shows Do Not Disturb in the display on all stations.
do NoT dIsTUrb
again.
To cancel, press
If you turn the answering system off while dNd is on, the phone
turns off dNd along with the answering system.
Using Call Block
If you subscribe to Caller ID, you can save phone numbers to the call
block list. When a call comes in, the phone compares the received
phone number to the numbers on the call block list. If the phone
number is on the list, the phone replaces the caller's name with Call
Blocked and disconnects the call. (The caller hears a reject tone.)
The call block list holds 20 entries, and all stations share the same
list. You can add entries through the Call Blocking menu, by selecting
Add Call Block in the CID menu, or by blocking incoming calls. (Only
one station can edit the call block list at a time.)
Blocking incoming calls
When the phone rings, wait until the display shows the Caller ID
information (usually after the second ring). If you want to block the
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
bLoCk
call and add this number to the call block list, press
. When the
MENU/sELECT
bLoCk
phone asks you to confirm, press
or
.
blocking an incoming call from an "Unknown" or "private"
number is the same as selecting Unknown Number or Private
Number from the Call Blocking menu.
Call Blocking menu options
With the phone in standby, open the menu and select Call Blocking
Choose one of these options:
.
View Number See the numbers on your call block list.
(Handset only) Add an entry to your call block list. The phone
will prompt you to enter a name & phone number.
Create New
Private
Number
(Handset only) Block all calls from numbers reported by CID
as "Private." (This does not count as one of the 20 entries.)
Unknown
Number
(Handset only) Block all calls from numbers reported by CID
as "Unknown". (This does not count as one of the 20 entries.)
Call block entry options
With the phone in standby, open the call block list and find the entry
MENU/sELECT
you want. Press
to open the individual entry menu.
Choose one of these options:
(Handset only) Edit this entry. The phone will prompt you to edit
the name & phone number.
Edit
Delete Erase this entry from the list & allow calls from this number.
Using Voice Message Notification
This feature supports frequency-shift keying (fsk) message
notification. Contact your voice mail provider for more details.
If you subscribe to a voice mail service, your phone
can notify you when you have a new message
waiting. When you have new messages, the voice
message icon
(
) appears in the display, and the
new message light (at the top of the handset) blinks.
Resetting the voice message indicator
If the voice message icon remains after you check
your messages, you can reset it. Open the menu on
the base and select VMWI Reset. Select Yes to reset the indicator.
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Multi-station Features
The expandable base and the cordless handset give you some useful
multi-station features. (A station can be any handset or the base.)
Expanding Your Phone
Your base supports a total of six cordless handsets: the one that
came with the base and up to five DCX210 accessory handsets.
Your base might be compatible with other Uniden accessory
handsets: please visit our website for a list of compatible handsets.
Accessory handsets must be registered to the base before you
can use them. Handsets that aren't registered display a Handset
not registered message. For instructions on registering handsets to
this base, see page 25 or the manual for the accessory handset.
Any accessory handsets that came packaged with the base are
already registered to that base for you.
If a handset was previously registered to a base, you have to reset
it so you can register it to a new base (see page 25 for DCX210).
Using Conference Calling
When an outside call comes in, the base
and two handsets can join in a
Outside call
Handset
#2
conference call with the outside caller. To
spEakEr
join the call, just press
on the
Handset
#1
TaLk/fLasH
base or
on a handset. To leave
Base
speakerphone
the conference call, hang up normally;
the other station remains connected to
the call. (You can also use the handset speakerphone for a
conference call, just like you can with a normal call.)
Using Privacy Mode
You can prevent other stations from joining a call. Start your call as
MENU/sELECT
usual, then press
: the display shows Call Privacy. Press
MENU/sELECT
again to turn privacy mode on (you'll see a in the
display). When you hang up, privacy mode turns off automatically.
As long you have privacy mode on, no other stations can interrupt
your call. To allow another station to join the call, just turn privacy
MENU/sELECT
mode off by repeating the process above (press
twice).
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Call Transfer
To...
From the base
From a handset
FIND hANDSET/INTErCOM
1. Press
put the call on hold.
CLEAr/INTErCOM
to 1. Press to
put the call on hold.
2. Select the station you want to transfer the call to, or select
transfer a
call
All to page all the stations at the same time.
When the other station accepts the call, you'll be disconnected,
but you can join the call again.
SPEAKEr
TALK/FLASh
Press to return to
the call.
cancel a
transfer
Press
call.
to return to the
1. To answer the page & speak to the transferring station,
accept a
transferred
call
FIND hANDSET/INTErCOM
CLEAr/INTErCOM.
press
.
press
press
2. To accept the call,
SPEAKEr
TALK/FLASh
.
press
.
Using the Intercom
Here are some things you need to know about using the intercom:
Whenever the phone is in standby, you can make an intercom call
between stations without using the phone line.
You can make an intercom call from any station, but only two
stations can be in an intercom call at any time.
If an outside call comes in during an intercom call, the phone shows
the CID information. If the other station hasn't answered the page,
the phone cancels the page so you can answer the incoming call.
To...
From the base
From a handset
FIND hANDSET/INTErCOM
CLEAr/INTErCOM
.
1. Press
.
1. Press
make an intercom
page
2. Select the station you want to talk with, or select All to
page all the stations at the same time.
FIND hANDSET/INTErCOM.
END
.
cancel a page
Press
Press
FIND hANDSET/INTErCOM
CLEAr/INTErCOM
or
answer an
intercom page
Press
or Press
SPEAKEr
TALK/FLASh
.
.
leave an intercom
call
FIND hANDSET/INTErCOM.
END
.
Press
Press
Press
answer an outside
call during an
intercom call
SPEAKEr.
TALK/FLASh
.
Press
ꢀꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Answering System
Setting Up Your Answering System
You can set up your answering system from any handset.
To...
Follow these steps
Your greeting can be between 2 seconds and 30 seconds
long. If you don't record an outgoing message, the system
uses a pre-recorded greeting: Hello, no one is available to
take your call. Please leave a message after the tone.
MESSAGES/MUTE
1. Press
to access the answering system. Wait
Record your
personal
5
until the system finishes its announcements, or press
(STOP)
to skip them.
outgoing
8
.
2. Press
message or
greeting
3. Wait for the system to say "Record greeting," then begin
speaking.
8
4. When you're finished, press to stop recording. The
system plays back your new greeting.
END
5. To keep this greeting, press
. To re-record it, go back to
step 2.
MESSAGES/MUTE
1. Press
to access the answering system. Wait
Switch
5
until the system finishes its announcements, or press
between the
pre-recorded
greeting &
your own
greeting
(STOP)
to skip them.
6
.
2. Press
The system plays back the greeting it is currently
using.
6
3. Press again to switch greetings.
1. Switch to your personal greeting following the steps above.
2. While the system is playing back your greeting, press .
Delete your
greeting
4
Ans. Setup menu options
You can change the answering system options from any handset.
Just open the menu and select Ans. Setup
.
Enter a 2-digit PIN so you can access your answering
system from any touch-tone phone (see page 21).
Security Code
Ring Time
Set the number of rings (
2
,
4
, or 6) before the answering
system answers the phone. Choose Toll Saver (TS) to
have the system pick up after 2 rings if you have new
messages or after 4 rings if you don't.
ꢀꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the amount of time callers have to leave a message,
Record Time
either
1
minute or
4
minutes. Choose Announce Only if
you don't want the system to let callers to leave a message.
Have the system beep every 15 seconds when you have
a new message; the beeping stops when you listen to all
your new messages. (To mute the alert without listening to
your messages, press any key on the base.)
Message Alert
Ans. Language Change the language of the system's voice prompts.
Turn on the call screen feature so you can hear callers as
they leave messages on the base speaker (see page 20).
Call Screen
Turn your answering system on or off. (To turn your
Ans. On/off
ON/OFF
system on or off from the base, just press
.)
Getting Your Messages
Accessing your answering system from a handset
You can access your system from a handset whenever the phone is
in standby.
Press MESSAGES/MUTE to start
remote operation mode.
1:Repeat 3:Skip
2:Play 4:Delete
Use PHONEBOOK/
LEFT to go to the
previous option.
6:SelectGreeting
5:Stop
[ / /select]
8:RecNewGreeting
Use CALLER ID/
RIGHT to go to the
next option.
Press MENU/
SELECT to choose
the current option.
Press END to exit remote
operation mode.
During remote operation, the phone beeps to let you know it's
waiting for your next command.
You can press the number key next to the commands instead of
scrolling through them.
If you don't press any keys for 30 seconds, the phone returns to
standby.
Only one handset can access the system at a time.
ꢀꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to operate your answering system
From a handset (remote
operation)
To...
From the base
PLAY/STOP
MESSAGES/MUTE
.
Press
Press
The system announces the number of new & old messages,
then plays the first new message followed by the day & time
it was received. Then the system plays the new messages
in the order they were received.
play new
messages
restart the
current message
PhONEBOOK/LEFT
1
Press
.
Press or select 1:Repeat
.
PhONEBOOK/LEFT
repeatedly until you hear the repeatedly until you hear the
message you want to replay. message you want to replay.
1
Press
Press or select 1:Repeat
replay previous
messages
CALLEr ID/rIGhT
3
skip a message Press
.
Press or select 3:Skip.
While the message is
While the message is playing,
delete a message
DELETE
4
playing, press
.
press or select 4:Delete
.
With the phone in standby,
DELETE
delete all of your press
. When the
Not available.
messages
system asks you to confirm,
DELETE
press
again.
After the system plays the new messages,
play old
messages
PLAY/STOP
PLAY/STOP
2
press
Press
again.
press or select 2:Play.
end the
operation
END
.
.
Press
Screening Your Calls
Another feature your answering system gives you is call screening.
While the system is taking a message, you can hear the caller on the
base speaker (if you turn on Call Screen) or from a handset.
To...
From the base
From a handset
hear the caller
Just listen to the caller over
MESSAGES/MUTE
Press
.
leaving a message the speaker.
SPEAKEr
TALK/FLASh
.
answer the call
mute the call screen
without answering
Press
.
Press
Press
END
or return the
CLEAr/MUTE
Press
.
handset to the cradle.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
If you mute the call screen, the system continues taking the
message: it just stops playing through the speaker.
Only one handset at a time can screen calls. If another handset is
screening the call, the handset beeps and returns to standby.
Using the System While You're Away from home
You can also operate your answering system from any touch-tone
phone. Before you can use this feature, you have to program a
security code.
Programming a security code
1) With the phone in standby, open the menu from any handset.
2) Select Ans. Setup, then select Security Code
.
3) Use the number keypad to enter a two-digit security code (01 to
MENU/sELECT
99). Press
when you’re finished.
remember to make a note of your new security code!
Dialing in to your system
1) Call your telephone number and wait for the system to answer. (If
your answering system is off, it will answer after about ten rings
and sound a series of beeps instead of your greeting.)
0
2) During the greeting (or beeps), press and immediately enter
your security code. (You have 3 tries to enter you security code:
if you enter it wrong 3 times, the system hangs up and returns to
standby.)
3) The system announces the current time, the number of messages
stored in memory, and a help prompt. Then it starts beeping
intermittently to let you know it's waiting for your command.
4) When you hear the intermittent
0-1 Repeat message
beeping, enter a command from the
chart to the right.
0-2 Play message
0-3 Skip message
If you don't press any keys for 15
seconds, the phone will hang up and
return to standby.
0-4 Delete message
0-5 Stop playback
0-6 Turn the system on
0-9 Turn the system off
1-0 Hear help prompts
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
If you have any trouble with your phone, try these simple steps first.
If you still have a question, call our Customer Care Line listed on the
front cover.
If…
Try…
-
-
Checking the telephone cord connection.
Disconnecting the base AC adapter. Wait a few
minutes, then reconnect it.
No stations can make
or receive calls.
-
-
Moving the handset closer to the base.
Resetting the handset.
One handset can’t
make or receive calls.
-
-
Making sure the ringer is turned on.
Making sure Do Not Disturb is turned off.
A station can make
calls, but it won’t ring.
-
-
Charging the battery for 15-20 hours.
Checking the battery pack connection.
A handset's display
won't turn on.
-
-
-
Charging the battery for 15-20 hours.
Checking the battery pack connection.
Resetting the handset.
A handset is not
working.
-
-
-
Moving the handset closer to the base.
Seeing if another station has Privacy Mode on.
Making sure the base is plugged in.
A handset says
Unavailable
.
-
-
-
Letting calls ring at least twice before answering.
Seeing if the call was placed through a switchboard.
Checking with your telephone service provider to
make sure your Caller ID service is active.
No stations will
display any Caller ID
information.
-
-
Making sure you entered the correct area code. If
you have to dial all 10 digits, you need to delete the
area code (see Seven-digit Dialing on page 12).
You may have to change the line mode. Contact
customer service for more information.
I can't dial from the
Caller ID list.
Caller ID displays
briefly & then clears.
I can’t transfer calls.
-
-
Resetting all the handsets.
Making sure both handsets are registered to this
base.
I can’t get two
handsets to talk to the
caller.
-
-
Making sure no station is in Privacy Mode.
The phone keeps
ringing if I answer on
an extension.
You may have to change the line mode. Contact
customer service for more information.
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
If…
Try…
-
-
Making sure the answering system is turned on.
Making sure the base AC adapter is plugged into a
continuous wall outlet (i.e., not controlled by a wall
switch).
The answering system
does not work.
-
-
Making sure the Record Time is not set to
The answering
system won't record
messages.
Announce Only
.
Deleting messages (the memory may be full).
-
-
Making sure no other handset is using the system.
Making sure the phone is in standby.
A handset can't access
the answering system.
My outgoing message
is gone.
-
Seeing if there was a power failure. You may have to
re-record your personal outgoing message.
-
-
Making sure call screening is turned on.
Changing the base speaker volume.
I can’t hear the base
speaker.
-
The incoming messages may be too long. Remind
callers to leave a brief message.
Deleting messages (the memory may be full).
Messages are
incomplete.
-
-
The system keeps
recording if I answer
on an extension.
You may have to change the line mode. Contact
customer service for more information.
-
-
Seeing if you already have 6 handsets registered to
this base.
Resetting the handset.
I can't register a
handset.
Weak or hard To hear Audio
If a caller’s voice sounds weak or soft, the signal might be blocked by
large metal objects or walls; you might also be too far from the base,
or the handset’s battery may be weak.
Try moving around while you’re on a call or moving closer to the
base to see if the sound gets louder.
Make sure the handset’s battery is fully charged.
Try adjusting the earpiece volume or the audio tone (see below).
Adjust the audio tone
During a call, open the menu and select Audio Tone. Choose one of
the three audio tone options: High Tone Natural Tone (recommended
,
for hearing aid users), or Low Tone. You may have to experiment to
figure out which audio tone works best for you.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Noise or Static On The Line
Interference is the most common
cause of noise or static on a
cordless phone. Here are some
common sources of interference:
Do you use a T-Coil hearing aid?
If you have a hearing aid
equipped with a telecoil (T-coil)
feature, the interaction between
the hearing aid & digital cordless
phones can cause noise in the
handset. If you have a T-coil
hearing aid & you have problems
with noise on the line, try turning
on T-coil mode. Open the menu.
Select Handset Setup, then
electrical appliances, especially
microwave ovens
computer equipment, especially
wireless LAN equipment and
DSL modems
select T-coil
.
radio-based wireless devices,
such as room monitors,
Using T-coil mode can shorten
the handset’s talk time; make
sure to watch the battery status
and keep the battery charged.
wireless controllers, or wireless
headphones or speakers
large florescent light fixtures
(especially if they give off a buzzing noise)
other services that use your phone line, like alarm systems,
intercom systems, or broadband Internet service
Here are some hints for when the static is...
on 1 handset or in 1 location:
on all handsets or in all locations:
-
Check nearby for one of the common
interference sources.
-
Check near the base for the
source of interference.
-
Try moving the handset away from a
suspected source, or try moving the
suspected source so it’s not between
the handset & the base.
-
Try moving the base away from a
suspected source, or turn off the
source if possible.
-
If the base has an adjustable
-
Try moving closer to the base. There is antenna, try raising the antenna
always more noise at the edges of the
base's range. If the handset displays an
Out of Range message, you need to
move closer to the base.
so it stands straight up.
-
If you have any service that uses
the phone line, you might need a
filter (see below).
Installing a line filter or DSL filter
Sometimes, broadband Internet services
that use the telephone line can interfere
with phones. One of these services−DSL−
often causes static on telephones. A DSL
filter or telephone line filter usually solves
ꢁꢃ
Telephone
wall jack
Telephone
cord
DSL filter
Download from Www.Somanuals.com. All Manuals Search And Download.
this problem. The technician who installed your DSL service might
have left some filters for you; if not, call your DSL provider or look in
any electronics store.
Plug the DSL filter into the telephone wall jack and plug your phone’s
base into the filter. Make a test call to make sure the noise is gone.
Changing from Tone to Pulse Dialing
Your phone can communicate with the telephone network in two
different ways: tone dialing or pulse dialing. These days, most
telephone companies use tone dialing. If your phone company uses
pulse dialing, you will need to change your phone’s dial mode.
1) From a handset, open the menu & select Global Setup
.
2) Select Dial Mode, then select Pulse. The phone sounds a
confirmation tone.
If you use pulse dialing and you need to send DTMF tones during a
call (if you're using an automated response system, for example),
press to temporarily switch to tone dialing. When the call ends, the
phone automatically returns to pulse dialing mode.
resetting and registering handsets
If you are having trouble with a handset or if you want to replace one,
you need to clear the registration information from the base and the
handset:
Do you have the base the handset is registered to?
Yes
No
END
#
END
#
1. Press & hold
and until the System 1. Press & hold
and until
Reset menu appears (about 5 seconds).
2. Select Deregister HS. The display lists
all registered handsets.
the System Reset menu
appears (about 5 seconds).
2. Select Base Unavailable
.
3. Select the handset you want to reset.
4. When the phone asks you to confirm,
select Yes. The handset clears its
information from the base & deletes it
own link to the base.
3. When the phone asks you
to confirm, select Yes. The
handset deletes its own link
without contacting the base.
When you reset a handset (or if you buy a new one), that handset
displays a Handset Not Registered message. If you see this message
on a handset, you need to register it to a base before you can use it.
ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Registering a handset
1) On the base, open the menu and select Register Handset. The
display should say Handset Registering
.
#
2) On the handset you want to register, press and hold until the
handset display says Handset Registering (about 2 seconds).
3) In about 30 seconds, the handset display should say Registration
TaLk/fLasH
Complete. Press
and make sure you get a dial tone.
If...
Try...
-
-
you don't hear a dial tone
the display says Registration Failed
Making sure the handset is fully
charged, then start over at step 1.
To register a handset to a different base, see the section
"Expanding Your phone" in the user's guide for the other base.
handling Liquid Damage
Moisture and liquid can damage your cordless phone.
If the handset or base is exposed to moisture or liquid, but only the
exterior plastic housing is affected, wipe off the liquid, and use as
normal.
If moisture or liquid has entered the plastic housing (i.e. liquid can
be heard in the phone or liquid has entered the handset battery
compartment or vent openings on the base), follow these steps:
handset
Base
1. Remove the battery cover & disconnect the
battery.
1. Disconnect the AC
adapter to cut off the
power.
2. Let dry for at least 3 days with the battery
disconnected and the cover off for ventilation. 2. Disconnect the
telephone cord.
3. After the handset dries, reconnect the battery
pack and replace the cover. Recharge the
battery fully (15-20 hours) before using.
3. Let dry for at least 3 days
before reconnecting.
IMporTaNT: You must unplug the telephone line while
recharging the battery pack to avoid charge interruption.
CAUTION! DO NOT use a microwave oven to speed up the
drying process. This will cause permanent damage to the
handset, base and the microwave oven.
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Terms Used In This Guide
Accessory An extra handset that can register to and be used with an expandable phone base. All accessory
handset
handsets must be registered to a base before you can use them.
The main part of the phone. It connects to your phone line and lets you make and receive calls.
Most bases also have a cradle to store a handset.
Base
CIDCW
(CID on Call Waiting.) A service that shows CID for calls that come in during another call.
Call Waiting A service that lets you receive calls while you are on another call.
Caller ID
Charger
(Also called CID.) A service that shows the name and number of incoming callers.
A cradle that stores and charges a handset but doesn’t connect to the phone line.
The part of the phone that stores a handset. While in a cradle, a handset is always in standby,
and any keys are locked.
Cradle
During a call The station is currently on a call or has activated a dial tone.
Handset A cordless handset that you use to dial the phone and talk to callers.
In standby The phone is inactive: there is no dial tone, no station is on a call or listening to messages.
Station Any handset or the base.
Specifications
Base
Charger
PS-00ꢂꢄ
ꢀꢁ0V AC, ꢅ0 Hz
Use only the supplied AC adapters.
Be sure to use the proper adapter for
the base & any chargers.
Do not place the power cord where it
creates a trip hazard or where it could
become chafed & create a fire or
electrical hazard.
Part number PS-00ꢂꢃ
Input voltage ꢀꢁ0V AC, ꢅ0 Hz
AC
adapter
Output voltage ꢆ.ꢇV AC @ ꢃꢄ0mA ꢇV AC @ ꢂ00mA
Part number BT-ꢀ0ꢀꢅ
Capacity
Battery
pack
ꢄ00mAh, ꢁ.ꢃV DC
Do not place the base in direct sunlight or subject it to high temperatures.
Battery Information
Fully charged, the battery should provide about ꢀ0 hours of talk time and about ꢆ days of standby time.
For best results, return the handset to the cradle after each call to keep it fully charged.
Keep an eye on the battery status icon. When the battery gets too low, the handset shows a low battery
alert. If you hear a strange beep during a call, check the display: if you see the low battery alert, finish
your conversation as quickly as possible and return the handset to the cradle. If the handset is in
standby, none of the keys will operate.
With normal use, the battery should last about one year. Replace the battery when the talk time
becomes short even when the battery is charged. To buy a replacement battery, call the Parts
Department listed on the front cover.
Rechargeable Nickel-Metal-Hydride Battery Warning
CAUTION! Risk of explosion if battery is replaced by an incorrect type! Dispose
of used batteries according to the instructions. Do not open or mutilate
the battery. Disconnect the battery before shipping this product.
This equipment contains a rechargeable Nickel-Metal-Hydride battery.
The rechargeable batteries contained in this equipment may explode if disposed of in a fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
Nickel is a chemical known to state of California to cause cancer.
Do not short-circuit the battery.
Do not charge the rechargeable battery pack used in this equipment with in any charger other than the
one designed to charge this battery pack as specified in the owner's manual. Using another charger
may damage the battery pack or cause the battery pack to explode.
Rechargeable Batteries Must Be Recycled or Disposed of Properly.
Uniden works to reduce lead content in PVC coated cords in our products & accessories.
Warning! The cords on this product and/or accessories contain lead,
a chemical known to the State of California to cause birth defects
or other reproductive harm. Wash hands after handling.
Compliance information
FCC Part 68 information
This equipment complies with Part ꢅꢇ of the FCC rules & the requirements adopted by the ACTA. On
the bottom of this equipment is a label that contains, among other information, a product identifier in the
format US: AAAEQ##TXXXX. If requested, this number must be provided to the phone company.
An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment
is provided (i.e., RJꢀꢀC) in the packaging with each piece of approved terminal equipment. A plug &
jack used to connect this equipment to the premises wiring & telephone network must comply with the
applicable FCC Part ꢅꢇ rules & requirements adopted by the ACTA. A compliant telephone cord &
modular plug is provided with this product. It is designed to be connected to a compatible modular jack
that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a phone line. Excessive
RENs on a phone line may result in devices not ringing in response to an incoming call. In most but not
all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may
be connected to a line, as determined by the total RENs, contact the telephone provider. The REN for this
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 0ꢂ is a REN of 0.ꢂ).
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice isn't practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary. The telephone company may make changes
in its facilities, equipment, operations or procedures that could affect the operation of the equipment.
If this happens the telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
Please follow instructions for repairing, if any (e.g. battery replacement section); otherwise do not
substitute or repair any parts of the device except as specified in this manual. Connection to party line
service is subject to state tariffs. Contact the state public utility commission, public service commission or
corporation commission for information. This equipment is hearing aid compatible.
If you experience trouble with this equipment, contact the manufacturer (see the cover of this manual for
contact information) or an authorized agent. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the equipment until the problem is resolved.
If your home has wired alarm equipment connected to a phone line, be sure that installing the system
does not disable your alarm equipment. If you have questions about what will disable alarm equipment,
contact your telephone company or a qualified installer.
Any changes or modifications to this product not expressly approved by the manufacturer or other party
responsible for compliance could void your authority to operate this product.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning
strikes, are very destructive to telephone equipment connected to AC power sources. To minimize
damage from these types of surges, a surge arrestor is recommended.
FCC Part 15 information
This device complies with part ꢀꢄ of the FCC rules. Operation is subject to the following two conditions:
(ꢀ) This device may not cause harmful interference, & (ꢁ) This device must accept any interference
received, including interference that may cause undesired operation. Privacy of communications may not
be ensured when using this phone.
FCC PART 15.105(b): Note: This equipment has been tested & found to comply with the limits for a Class
B digital device, pursuant to part ꢀꢄ of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses & can
radiate radio frequency energy and, if not installed & used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off & on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This product complies with FCC radiation exposure limits under the following conditions:
The base must be placed to allow a minimum of ꢁ0 cm (ꢇ inches) between the antenna and all persons
during normal operation.
The base must not be collocated or operated in conjunction with any other antenna or transmitter.
The handset is designed for body-worn operation and meets FCC RF exposure guidelines when
used with any belt clip, carrying case, or other accessory supplied with this product. (All necessary
accessories are included in the package; any additional or optional accessories are not required for
compliance with the guidelines.) Third party accessories (unless approved by the manufacturer) should
be avoided as these might not comply with FCC RF exposure guidelines.
Industry Canada (I.C.) Notice
Terminal equipment
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation IC before the registration
number signifies that registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment
itself. The REN assigned to each terminal equipment provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed ꢄ.
Radio equipment
The term IC before the radio certification number only signifies that Industry Canada technical
specifications were met. Operation is subject to the following two conditions: (1) this device may not
cause interference, & (ꢁ) this device must accept any interference, including interference that may cause
undesired operation of the device. "Privacy of communications may not be ensured when using this
telephone".
Download from Www.Somanuals.com. All Manuals Search And Download.
One-year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF WARRANTY: Uniden
warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials
& craftsmanship with only the limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect ꢀꢁ
months after the date of original retail sale. The warranty is invalid if the Product is (A) damaged or not
maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired
by someone other than an authorized Uniden service center for a defect or malfunction covered by this
warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured
by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time
while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit &
return it to you without charge for parts, service, or any other cost (except shipping & handling) incurred
by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at
its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH
ABOVE IS THE SOLE & ENTIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF &
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, & you may also have other rights which
vary from state to state. This warranty is void outside the United States of America & Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in
the owner's manual you are certain that the Product is defective, pack the Product carefully (preferably
in its original packaging). Disconnect the battery from the Product & separately secure the battery in its
own separate packaging within the shipping carton. The Product should include all parts & accessories
originally packaged with the Product. Include evidence of original purchase & a note describing the defect
that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to
warrantor at:
As an Energy Star® Partner, Uniden has determined that
Uniden America Service
this product meets the Energy Star® guidelines for energy
ꢃꢆ00 Amon Carter Blvd.
efficiency. Energy Star® is a U.S. registered mark.
Fort Worth, TX ꢆꢅꢀꢄꢄ
®
Uniden is a registered trademark of Uniden America Corporation.
Call waiting, CID, CIDCW, and Voice Mail are telephone line services. Your phone
supports these services, but you have to arrange for them through your telephone provider. Contact
your provider for details.
The pictures in this manual are for example only. Your phone may not look exactly like the pictures.
May be covered under one or more of the following U.S. patents:
ꢅ,ꢅꢀꢇ,0ꢀꢄ ꢅ,ꢆꢀꢃ,ꢅꢂ0 ꢅ,ꢆꢇꢁ,0ꢈꢇ ꢅ,ꢆꢇꢇ,ꢈꢁ0 ꢅ,ꢆꢇꢇ,ꢈꢄꢂ ꢅ,ꢇꢂꢈ,ꢄꢄ0 ꢅ,ꢇꢇꢈ,ꢀꢇꢃ ꢅ,ꢈ0ꢀ,ꢁꢆꢀ ꢅ,ꢈ0ꢆ,0ꢈꢃ
ꢅ,ꢈꢀꢃ,ꢈꢃ0 ꢅ,ꢈꢃ0,ꢇꢅꢆ ꢅ,ꢈꢄꢂ,ꢀꢀꢇ ꢆ,0ꢁꢂ,ꢀꢆꢅ ꢆ,0ꢂ0,ꢇꢀꢈ ꢆ,ꢀꢃꢅ,ꢀꢅ0 ꢆ,ꢁ0ꢂ,ꢂ0ꢆ ꢆ,ꢁ0ꢅ,ꢃ0ꢂ ꢆ,ꢂꢀ0,ꢂꢈꢇ
Other patents pending.
© 2009 Uniden America Corp.
Ft. Worth, TX 76155
Printed in Vietnam
UNZZ01048BA(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
|
