Operator’s Manual
Two-Stage Snow Thrower
8526—Storm
9528—Storm
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine
authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
FORM NO. 769-01279A.
(7/30/2004)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
4. Use a grounded three-wire extension cord and
receptacle for all units with electric start engines.
5. Adjust collector housing height to clear gravel or
crushed rock surfaces.
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 14 years old to operate
this machine. Children 14 years old and over
should read and understand the operation
instructions and safety rules in this manual and
should be trained and supervised by a parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Thrown objects can cause serious personal injury.
Plan your snow-throwing pattern to avoid discharge
of material toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at
least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling,
especially when operating in reverse.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while
engine is running, except where specifically
recommended in the operator’s manual.
8. Let engine and machine adjust to outdoor
temperature before starting to clear snow.
9. To avoid personal injury or property damage use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes
before refueling.
f. Never over fill fuel tank. Fill tank to no more
than ½ inch below bottom of filler neck to
provide space for fuel expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine
and equipment. Move machine to another
area. Wait 5 minutes before starting the
engine.
i. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light (e.g. furnace, water heater, space
heater, clothes dryer etc.).
Preparation
1. Thoroughly inspect the area where the equipment
is to be used. Remove all doormats, newspapers,
sleds, boards, wires and other foreign objects,
which could be tripped over or thrown by the auger/
impeller.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or
repair to protect your eyes. Thrown objects which
ricochet can cause serious injury to the eyes.
3. Do not operate without wearing adequate winter
outer garments. Do not wear jewelry, long scarves
or other loose clothing, which could become
entangled in moving parts. Wear footwear which
will improve footing on slippery surfaces.
j. Allow machine to cool at least 5 minutes
before storing.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Never put your hand in the discharge or collector
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine
and remain behind handles until all moving parts
have stopped before unclogging.
19. Use only attachments and accessories approved
by the manufacturer (e.g. wheel weights, tire
chains, cabs etc.).
20. If situations occur which are not covered in this
manual, use care and good judgment. Contact your
dealer or call (800) 520-5520 for assistance and the
name of your nearest servicing dealer.
Operation
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact
with the rotating parts can amputate hands and
feet.
2. The auger/impeller control lever is a safety device.
Never bypass its operation. Doing so makes the
machine unsafe and may cause personal injury.
3. The control levers must operate easily in both
directions and automatically return to the
disengaged position when released.
4. Never operate with a missing or damaged chute
assembly. Keep all safety devices in place and
working.
Maintenance & Storage
5. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
6. Do not operate machine while under the influence
of alcohol or drugs.
7. Muffler and engine become hot and can cause a
burn. Do not touch.
8. Exercise extreme caution when operating on or
crossing gravel surfaces. Stay alert for hidden
hazards or traffic.
9. Exercise caution when changing direction and
while operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding
possible property damage or personal injury
caused by a ricochet.
11. Never direct discharge at children, bystanders and
pets or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to
clear snow at too fast of a rate.
13. Never operate this machine without good visibility
or light. Always be sure of your footing and keep a
firm hold on the handles. Walk, never run.
14. Disengage power to the auger/impeller when
transporting or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use
care when backing up.
16. If the machine should start to vibrate abnormally,
stop the engine, disconnect the spark plug wire and
ground it against the engine. Inspect thoroughly for
damage. Repair any damage before starting and
operating.
17. Disengage all control levers and stop engine before
you leave the operating position (behind the
handles). Wait until the auger/impeller comes to a
complete stop before unclogging the chute
assembly, making any adjustments, or inspections.
1. Never tamper with safety devices. Check their
proper operation regularly. Refer to the
maintenance and adjustment sections of this
manual.
2. Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine.
Wait until the auger/impeller come to a complete
stop. Disconnect the spark plug wire and ground
against the engine to prevent unintended starting.
3. Check bolts and screws for proper tightness at
frequent intervals to keep the machine in safe
working condition. Also, visually inspect machine
for any damage.
4. Do not change the engine governor setting or over-
speed the engine. The governor controls the
maximum safe operating speed of the engine.
5. Snow thrower shave plates and skid shoes are
subject to wear and damage. For your safety
protection, frequently check all components and
replace with original equipment manufacturer’s
(OEM) parts only. “Use of parts which do not meet
the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage
and disengage properly and adjust, if necessary.
Refer to the adjustment section in this operator’s
manual for instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear
snow from machine and prevent freeze up of auger/
impeller.
10. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as a water heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR RESPONSIBILITY
Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in
this manual and on the machine.
Do not modify engine
Notice regarding Emissions
To avoid serious injury or death, do not modify engine
in any way. Tampering with the governor setting can
lead to a runaway engine and cause it to operate at
unsafe speeds. Never tamper with factory setting of
engine governor.
Engines which are certified to comply with California
and federal EPA emission regulations for SORE (Small
Off Road Equipment) are certified to operate on regular
unleaded gasoline, and may include the following
emission control systems: Engine Modification (EM)
and Three Way Catalyst (TWC) if so equipped.
SAFETY LABELS FOUND ON YOUR SNOW THROWER
DANGER
DANGER
1.KEEP AWAY FROM ROTATING IMPELLER
AND AUGER. CONTACT WITH IMPELLER OR
AUGER CAN AMPUTATE HANDS AND FEET
.
DANGER
USE CLEAN-OUT TOOL TO UNCLOG
2.
3.
DISCHARGE CHUTE.
DISENGAGE CLUTCH LEVERS, STOP ENGINE,
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
TO AVOID THROWN OBJECTS INJURIES,
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
4.
5.
AVOID INJURY FROM
ROTATING AUGER -
KEEP HANDS, FEET
AND CLOTHING AWAY.
READ OPERATOR'S MANUAL.
CLEAN-OUT TOOL
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS.
SHUT OFF ENGINE AND WAIT UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING.
CAUTION
Muffler and adjacent surfaces
are HOT. Do not touch.
AVERTISSMENT
Silencieux et surfaces adjacentes
TRES CHAUDES. Ne pas toucher.
USE CLEAN-OUT TOOL OR WOODEN STICK TO
UNCLOG DISCHARGE CHUTE.
CUIDADO
El silenciador y las areas alredador
estan CALIENTES. No tocar.
2082
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: ASSEMBLING YOUR SNOW THROWER
1
2
3
4
NOTE: References to right or left side of the snow
thrower are determined from behind the unit in the
operating position (standing directly behind the snow
thrower, facing the handle panel).
IMPORTANT: Two replacement auger shear pins are
included with this manual (or stowed in the plastic
information regarding shear pin replacement.
CAUTION: Prior to operating your snow
Read and follow all instructions carefully and
perform all adjustments to verify your snow
thrower is operating safely and properly.
1. Observe the lower rear area of the snow thrower to
be sure both cables are aligned with roller guides
before pivoting the handle upward.
2. Secure the upper shift rod to the lower shift rod by
sliding the connector sleeve downward.
•
Secure the handle by tightening the plastic wing
knob located on both the left and right sides of the
handle. Remove and discard any rubber bands, if
present. They are for packaging purposes only.
3. Apply a light lubricant (i.e. 3-in-1 oil) to the rim/lip of
the chute base (and the underside of the chute
assembly) and position the chute assembly over
the base.
4. Close the flange keepers to secure the chute
assembly to the chute base. The flange keepers
will click into place when properly secure.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If the flange keepers will not easily click into
place, use the palm of your hand to apply swift, firm
pressure to the back of each.
5
5. Remove the clevis pin and hairpin clip from the
upper portion of the chute mast.
•
Position the control head over the chute mast and
rear portion of the chute assembly.
•
Re-insert the clevis pin and secure with the hairpin
clip removed earlier.
CAUTION: Prior to operating your snow
Read and follow all instructions carefully and
perform all adjustments to verify your snow
thrower is operating safely and properly.
Tire Pressure
•
Before operating, check tire pressure and reduce
pressure in both tires to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires,
the unit may not travel in a straight path and the shave
plate may wear unevenly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: KNOW YOUR SNOW THROWER
Shift Lever
Drive Control
Chute Directional Control
Auger Control
Electric Starter Button
Gas Cap
Engine Controls
Recoil Starter
Handle
Oil Fill
Electric Starter Outlet
Primer
Chute Assembly
Clean-out
Tool
Ignition
Key
Spark Plug Cover
Choke
Control
Throttle
Control
Skid Shoe
Augers
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
Choke Control
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the
Tecumseh Engines manual packed separately and
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating
the choke control closes the choke plate on the
carburetor and aids in starting the engine.
Shift Lever
The shift lever is located on the right side
of the handle panel. Place the shift lever
into any of eight positions to control the
direction of travel and ground speed.
Throttle Control
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine when
pushed down completely.
Forward
There are six forward (F) speeds.
Position one (1) is the slowest and
position six (6) is the fastest.
Primer
Depressing the primer forces fuel directly
into the engine’s carburetor to aid in cold-
weather starting.
Reverse
There are two reverse (R) speeds. One
(1) is the slower and two (2) is the faster.
Oil Fill
Gas Cap
Engine oil level can be checked and oil
added through the oil fill.
Unthread the gas cap to add gasoline to
the fuel tank.
STOP
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Control
Ignition Key
The ignition key is a safety devise. It must be fully
inserted in order for the engine to start. Remove the
ignition key when the snow thrower is not in use.
AUGER
CONTROL
IMPORTANT: Do not turn the ignition key in an attempt
to start the engine. Doing so may cause it to break.
Clean-Out Tool
WARNING: Never use your hands to clear
a clogged chute assembly. Shut off engine
and remain behind handles until all moving
parts have stopped before unclogging.
GO
The auger control is located on the left handle.
Squeeze the control grip against the handle to engage
the augers and start snow throwing action. Release to
stop.
The chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is
designed to clear a clogged chute assembly. Refer to
Operating Your Snow Thrower section for more detailed
information regarding the chute clean-out tool.
Drive Control
NOTE: This item is fastened with a cable tie to the
rear of the auger housing at the factory. Cut the cable
tie before operating the snow thrower.
DRIVE
CONTROL
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
GO
Recoil Starter Handle
This handle is used to manually start the engine.
The drive control is located on the right handle.
Squeeze the control grip against the handle to engage
the wheel drive. Release to stop.
Electric Starter Button
Pressing the electric starter button engages the
engine’s electric starter when plugged into a 120V
power source.
Chute Directional Control
CHUTE DIRECTIONAL CONTROL
Electric Starter Outlet
CHUTE TILT DOWN
Requires the use of a three-prong outdoor extension
cord and a 120V power source/wall outlet.
PUSH BUTTON
PUSH BUTTON
Augers
CHUTE ROTATE
CHUTE ROTATE
When engaged, the augers rotate and draw snow into
the auger housing.
LEFT
RIGHT
Chute Assembly
CHUTE TILT UP
Snow drawn into the auger housing is discharged out
the chute assembly.
The chute directional control is located on the left side
of the dash panel.
•
To change the direction in which snow is thrown,
squeeze the button on the joy-stick and pivot the
joy-stick to the right or to the left.
To change the angle/distance which snow is
thrown, pivot the joy-stick forward or backward.
Spark Plug Cover
Unscrew 1/4-turn to access the spark plug and spark
plug wire.
•
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATING YOUR SNOW THROWER
WARNING: If your home electrical
system is grounded, but a three-hole
receptacle is not available, do not use your
snow thrower’s electric starter.
Before Starting
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
If you have a grounded three-prong receptacle,
proceed as follows:
Gas & Oil Fill-Up
•
Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of
extension cord into a three-prong 120-volt,
grounded, AC outlet in a well-ventilated area.
Rotate choke control to FULL choke position (cold
engine start).
Service the engine with gasoline and oil as instructed in
the Tecumseh Engines manual packed separately with
your snow thrower. Read instructions carefully.
•
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel the machine indoors or while the
engine is hot or running. Extinguish cigarettes,
cigars, pipes and other sources of ignition.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
•
Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
•
A small plastic cup may be located inside the fuel fill
opening beneath the gas cap. Remove and discard
this cup before filling up the tank.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
Starting The Engine
•
•
Push starter button to start engine.
Once the engine starts, immediately release starter
button.
•
Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over
the metal tip on the spark plug.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to FULL and
then slowly into the OFF position again.
When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
•
•
Make certain both the auger control and drive
control are in the disengaged (released) position.
Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
•
NOTE: The engine cannot start unless the key is
Recoil Starter
inserted into ignition switch.
•
Rotate choke control to FULL choke position (cold
engine start).
Electric Starter
•
Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
•
Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
CAUTION: If your home’s wiring system
is not a three-wire grounded system, do
not use this electric starter under any
conditions.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
WARNING: The optional electric starter is
equipped with a grounded three-wire power
cord and plug, and is designed to operate on
120 volt AC household current. It must be
used with a properly grounded three-prong
receptacle at all times to avoid the possibility
of electric shock. Follow all instructions
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
•
Grasp the recoil starter handle and slowly pull the
rope out. At the point where it becomes slightly
harder to pull the rope, slowly allow the rope to
recoil.
carefully prior to operating the electric starter.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Pull the starter handle with a firm, rapid stroke.
To Engage Drive
IMPORTANT: Do not release the handle and allow it to
snap back. Keep a firm hold on the starter handle and
allow it to slowly recoil.
•
With the throttle control in the Fast (rabbit) position,
move shift lever into one of the six forward (F)
positions or two reverse (R) positions. Select a
speed appropriate for the snow conditions and a
pace you’re comfortable with.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to the FULL
position and then slowly into the OFF position
again.
IMPORTANT: Use the slower speeds until you are
comfortable and familiar with the operation of the snow
thrower.
•
Squeeze the drive control against the handle the
snow thrower will move. Release it and drive
motion will stop.
Stopping The Engine
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible starter freeze-up, proceed
as follows:
IMPORTANT: NEVER reposition the shift lever (change
speeds or direction of travel) without first releasing the
drive control and bringing the snow thrower to a
complete stop. Doing so will result in premature wear to
the snow thrower’s drive system.
•
Electric Starter (on models so equipped)
1. Connect extension cord to the electric starter outlet
on the engine, then to 120 volt AC outlet.
2. With the engine running, push the starter button
and allow the starter for spin for several seconds.
The noise made by the starter is normal. The
engine’s starter is not being harmed.
3. When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
4. Move throttle control to STOP position.
5. Remove the ignition key.
6. Wipe all snow and moisture from the area around
the engine as well as the area in and around the
drive control and auger control. Also, engage and
release both controls several times.
To Engage Augers
•
To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
Auger Control Test
IMPORTANT: Perform the following test before
operating your snow thrower for the first time and at the
start of each winter season.
Check the adjustment of the auger control as follows:
•
When the auger control is released and in the
disengaged “up” position, the cable should have
very little slack. It should NOT be tight.
•
In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting the Engine. Make sure the throttle is
set in the FAST position.
While standing in the operator’s position (behind
the snow thrower), engage the auger.
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
Recoil Starter
•
•
1. With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud
clattering sound, which is not harmful to engine.
2. Move throttle control to STOP position.
3. Remove the ignition key.
Allow the auger to remain engaged for
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the throttle control in the FAST (rabbit)
position and the auger control in the disengaged
“up” position, walk to the front of the machine.
Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
•
•
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
4. Wipe all snow and moisture from the area around
the engine as well as the area in and around the
drive control and auger control. Also, engage and
release both controls several times.
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for ALL moving parts to stop before
re-adjusting the auger control.
•
To readjust the control cable, loosen the hex jam
nut on the auger control cable “Z” fitting.
Rotate the coupling end of the cable
•
counterclockwise to provide more slack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Retighten the hex jam nut. See Figure 1.
Repeat Auger Control Test to verify proper
adjustment has been achieved.
•
While standing in the operator’s position (behind
the snow thrower), engage the auger control for a
few seconds to clear any remaining snow and ice
from the chute assembly.
Drive / Auger Lock
The drive/auger lock allows the user to operate the
snow thrower with one hand, leaving the left hand free
to operate the chute directional control.
•
Engage both the Auger Control and the Drive
Control at the same time.
•
Release the Auger Control and it will remain
engaged until the Drive Control is also released.
Operating Tips
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power
until it reaches operating temperature.
WARNING: The muffler, engine and
surrounding areas become hot and can
cause a burn. Do not touch.
Figure 1
Chute Clean-Out Tool
•
•
•
Discharge snow downwind whenever possible.
Slightly overlap each previous swath.
Set the skid shoes 1/4” below the scraper bar for
normal usage. The skid shoes may be adjusted
upward for hard-packed snow. Adjust downward
when using on gravel or crushed rock.
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly
during operation, proceed as follows to safely clean the
chute assembly and chute opening:
•
Release both the Auger Control and the Drive
Control
•
Avoid possible starter freeze-up. Clean the snow
thrower thoroughly after each use.
.
•
•
Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
•
•
WARNING: Never use your hands to clean
snow and ice from the chute assembly or
auger housing
Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: MAKING ADJUSTMENTS
WARNING: Never attempt to make any
adjustments while the engine is running,
except where specified in operator’s manual.
1
Shift Rod Adjustment
If the full range of speeds (forward and reverse) cannot
be achieved, refer to the figures to the right and adjust
the shift rod as follows:
1. Place the shift lever in the fastest forward speed
position and remove the hairpin clip which secures
the ferrule to the shift lever.
2. Rotate the shift arm clockwise as far as it will go.
3. Thread the ferrule up or down the shift rod until it
aligns with the hole in the shift lever. Resecure the
ferrule with the hairpin clip removed earlier.
Auger Control
control.
2
Tire Pressure
•
Before operating, check tire pressure and reduce
pressure to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires,
the unit may pull to one side or the other.
3
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Control
When the drive control is released and in the
disengaged “up” position, the cable should have very
little slack. It should NOT be tight.
Check the adjustment of the drive control as follows:
1. With the drive control released, push the snow
thrower gently forward. The unit should roll freely.
2. Engage the drive control and gently attempt to push
the snow thrower forward. The wheels should not
turn. The unit should not roll freely.
3. With the drive control released, move the shift lever
back and forth between the R2 position and the F6
position several times. There should be no
resistance in the shift lever.
If any of the above tests failed, the drive cable is in need
of adjustment. refer to the figure at the right and
proceed as follows:
Figure 2
Figure 3
Figure 4
•
Loosen the hex jam nut on the auger control cable
“Z” fitting and rotate the coupling end of the cable
downward to provide more slack or upward to take
up slack. See Figure 2.
•
Retighten the hex jam nut and repeat all three tests
to verify proper adjustment has been achieved.
Skid Shoes
The space between the skid shoes and the ground can
be adjusted. See Figure 3.
•
For close snow removal on a smooth surface, raise
skid shoes higher on the auger housing.
•
Use a middle or lower position when the area to be
cleared is uneven, such as a gravel driveway.
CAUTION: Loose gravel can be picked up
and thrown by the auger, causing injury to the
operator and bystanders and/or damage to
the snow thrower and surrounding property.
•
•
Adjust skid shoes by loosening the four hex nuts
(two on each side) and carriage bolts. Move skid
shoes to desired position.
Make certain the entire bottom surface of skid shoe
is against the ground to avoid uneven wear on the
skid shoes. Retighten nuts and bolts securely.
Joy-Stick Cable Adjustment
If the chute assembly does not have full range from left-
to-right, or upward-and-downward, the joy-stick cables
can be adjusted to take up slack:
•
Using a ½” wrench, loosen the upper and lower hex
nuts found on one cable adjuster.
•
Grasp the metal cable housing and gently push
upward to take up slack (usually no more than 1/4-
inch) in the cable before retightening both hex nuts.
Repeat on each of four cable adjusters until the
chute assembly has full range in all directions.
•
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER
Auger Shaft
WARNING: Before lubricating, repairing, or
inspecting, disengage all controls and stop
engine. Wait until all moving parts have come
to a complete stop.
•
At least once a season, remove the shear pins on
auger shaft. Spray lubricant inside shaft, around
the spacers. Also lubricate the grease fittings found
at either end of the shaft. See Figure 6.
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine maintenance.
Fitting
Spacers
Fitting
Lubrication
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine lubrication
instructions.
Gear Shaft
The gear (hex) shaft should be lubricated at least once
a season or after every 25 hours of operation.
•
Remove the lower frame cover by removing the two
screws which secure it.
•
Apply a light coating of an all-weather multi-
Shear Pins
Shear Pins
Figure 6
Gear Case
A grease fitting can be found on the gear case. After
removing the vent plug found on the top of the gear
case, lubricate with two ounces of grease (Part Number
737-0168) once a season.
IMPORTANT: If the vent plug is not removed before
lubricating the gear case, damage to the seals could
result.
WARNING: Before servicing, repairing, or
inspecting, disengage all controls and stop
engine. Wait until all moving parts have come
to a complete stop.
Shave Plate and Skid Shoes
•
The shave plate and skid shoes on the bottom of
the snow thrower are subject to wear. They should
be checked periodically and replaced when
necessary.
To remove skid shoes, remove the four carriage
bolts and hex flange nuts which secure them to the
snow thrower. Reassemble new skid shoes with the
four carriage bolts (two on each side) and hex
flange nuts. Refer to Figure 3.
Figure 5
IMPORTANT: Keep lubricant off the friction wheel and
drive plate.
•
Wheels
•
At least once a season, remove both wheels. Clean
and coat the axles with a multipurpose automotive
grease before reinstalling wheels.
•
To remove shave plate, remove the carriage bolts
and hex nuts which attach it to the snow thrower
housing. Reassemble new shave plate, making
sure heads of carriage bolts are to the inside of
housing. Tighten securely.
Chute Directional Control
•
Once a season, the joystick should be lubricated
with petroleum jelly, linseed oil, mineral oil, paraffin
wax or 3-in-1 oil.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
3. Roll the auger belt off the engine pulley.
4. Unhook the support bracket spring from the frame.
•
Loosen and remove the shoulder screw which acts
as a belt keeper.
•
Remove the belt from around the auger pulley, and
slip the belt between the support bracket and the
auger pulley
•
Reassemble auger belt by following instructions in
reverse order.
2
IMPORTANT: Do NOT forget to reinstall the shoulder
screw and reconnect the spring to the frame after
installing a replacement auger belt.
4
3
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
3.
a. Grasp the idler pulley and pivot it toward the
right.
b. Insert a screw driver through aligning holes in
both the idler bracket and the engine.
c. Roll the auger belt off the engine pulley.
d. Lift the drive belt off engine pulley.
4. Slip the drive belt off the pulley and between friction
wheel and friction wheel disc.
2
•
Remove and replace belt in the reverse order.
3
4
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Friction Wheel Removal
If the snow thrower fails to drive with the drive control
engaged, and performing the drive control cable
friction wheel may need to be replaced. Follow the
instructions below. Examine the friction wheel for signs
of wear or cracking and replace if necessary
1
2
3
•
•
Place the shift lever in third Forward (F3) position.
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
•
1.
a. Remove the frame cover from the underside
of the snow thrower by removing four self-
tapping screws which secure it.
b. Remove the right-hand wheel by removing
the screw and bell washer which secure it to
the axle.
c. Locate the hex shaft and E-ring on the right
side of the snow thrower frame, about two
inches from the wheel axle.
c. Using a suitable tool, carefully remove the
outer E-ring which secures the hex shaft to
the snow thrower frame and lightly tap the
shaft’s end to dislodge the ball bearing from
the right side of the frame.
2.
a. Slide the hex shaft downward and to the left
while carefully un-meshing the lower gears
on the hex shaft from the upper gears on the
wheel axle.
b. Set the hex shaft’s gears aside.
c. Carefully remove the inner E-ring from the
hex shaft and slide the friction wheel
assembly off the hex shaft.
NOTE: If you’re replacing the friction wheel assembly
as a whole, discard the worn part and slide the new part
onto the hex shaft. Follow the steps above in reverse
order to reassemble components. If you’re
disassembling the friction wheel and replacing only the
rubber ring, proceed as follows:
3. Remove the four screws which secure the friction
wheel’s side plates together.
•
•
Remove the rubber ring from between the plates.
Reassemble the side plates with a replacement
rubber ring.
IMPORTANT: Tighten each screw only one rotation
before turning the wheel clockwise and proceeding with
the next screw. Repeat this process several times to
ensure the plates are secured with equal force.
•
Slide the friction wheel assembly back onto the hex
shaft and follow the steps above in reverse order to
reassemble components.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: NEVER replace the auger shear pins with
anything other than OEM Part No.738-04124
replacement shear pins. Any damage to the auger
gearbox or other components as a result of failing to do
so will NOT be covered by your snow thrower’s
warranty.
Augers
•
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If the auger should strike
a foreign object or ice jam, the snow thrower is
designed so that the pins may shear.
•
If the augers will not turn, check to see if the pins
have sheared. One set of replacement shear pins
has been provided with the snow thrower. When
replacing pins, spray an oil lubricant into shaft
before inserting new pins.
SECTION 7: OFF-SEASON STORAGE
•
Drain carburetor by pressing upward on bowl drain,
located below the carburetor cover.
WARNING: Never store the machine or
fuel container indoors where there is an open
flame, spark or pilot light such as on a water
heater, furnace, clothes dryer or other gas
appliances.
NOTE: Fuel stabilizers, such as STA-BIL®, are an
acceptable alternative in minimizing the formation of
fuel gum deposits during storage. Do not drain
carburetor if using a fuel stabilizer.
WARNING: Drain fuel into an approved
container outdoors, away from open flame.
Allow engine to cool. Extinguish cigarettes,
cigars, pipes, and other sources of ignition
prior to draining fuel. Fuel left in engine for
extended period deteriorates and will cause
serious starting problems.
•
•
Wipe equipment with an oiled rag to prevent rust.
Remove spark plug and pour one ounce of engine
oil through spark plug hole into cylinder. Cover
spark plug hole with rag. Crank engine several
times to distribute oil. Replace spark plug.
Follow the lubrication recommendations found in
the Maintenance Section.
•
•
If unit is to be stored over 30 days, prepare for storage
as follows:
Always store the snow thrower in a clean, dry area.
When storing any type of power equipment in an
unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.
•
Remove gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts
and causing possible malfunction of engine.
Run engine until fuel tank is empty and engine
stops due to lack of fuel.
•
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: TROUBLE SHOOTING GUIDE
Trouble
Possible Cause(s)
Corrective Action
Engine fails to start
Fuel tank empty, or stale fuel.
Fill tank with clean, fresh gasoline. Fuel will not last over thirty days
unless a fuel stabilizer is used.
Blocked fuel line.
Clean fuel line.
Choke control not in ON position Move choke control to ON position
Faulty spark plug.
Clean, adjust gap or replace.
Ignition key not present.
Spark plug wire disconnected.
Engine not primed.
Insert key into ignition switch.
Connect spark plug wire.
Refer to the Tecumseh engine manual or Starting the Engine on page
10 of this manual for instructions on the engine primer.
Move choke control to OFF position.
Engine runs erratic
Loss of power
Unit running on CHOKE.
Blocked fuel line or stale fuel.
Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last
over thirty days unless a fuel stabilizer is used.
Drain fuel tank. Refill with fresh fuel.
Refer to the Tecumseh engine manual.
Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean following the engine manual.
Refer to the Tecumseh engine manual packed with your unit or
have carburetor adjusted by an authorized service dealer.
Water or dirt in fuel system.
Carburetor out of adjustment.
Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.
Carburetor not adjusted
properly.
Engine overheats
Excessive vibration
Loose parts or damaged auger. Stop engine immediately and disconnect spark plug wire. Tighten
all bolts and nuts. Make all necessary repairs. If vibration
continues, have unit serviced by an authorized service dealer.
Unit fails to propel itself Incorrect adjustment of drive
control cable.
Adjust drive control cable.
Drive belt loose or damaged.
Replace drive belt.
Unit fails to
discharge snow
Chute assembly clogged.
Stop engine immediately. Clean chute assembly and inside of
auger housing with chute clean-out tool
Foreign object lodged in auger. Stop engine immediately. Remove object from auger.
Incorrect adjustment of auger
control cable.
Adjust auger control cable.
Drive belt loose or damaged.
Replace drive belt.
NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Style Q
REF.
NO.
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Panel Assembly, Handle, Q-Style
(Inc. Ref. 47)
Handle Assembly, Clutch Lock, LH
(Inc. Ref. 48)
Handle Assembly, Clutch Lock, RH
(Inc. Ref. 48)
Handle Assembly, Engagement, LH
Handle Assembly, Engagement, RH
Screw, #8-16 x .50
DESCRIPTION
Screw, Shoulder, .374 Dia. x 1.05
Z-Fitting, Cable
Rod, Shift, .312 x 8.98 Upper
Connector Sleeve, Shift Rod
Lever, Shift
1
2
3
631-04127
631-04133
631-04134
29 738-04125
30 746-0778
31 747-04348
32 750-0963
33 790-00130
34 790-00140
35 710-0449
36 710-0726
37 720-0284
38 736-0451
39 749-04138
40 749-04141
41 749-04142
42 712-04063
43 726-0135
44 732-04205
45 790-00156
46 747-04257
47 731-04885
48 712-0161
49 684-04116
Bracket, Panel
4
5
6
7
8
9
684-04105
684-04106
710-04326
710-04354
710-1026
710-1233
Screw, Carriage, 5/16-18, 2.25, Gr5
Screw, 5/16-12, 0.750
Wing Knob, 5/16-18
Washer, Saddle, 320 x .93 x .060
Handle, Lower, Snow
Handle, Upper, RH
Handle, Upper, LH
Nut, Flange Lock, Nylon, 5/16-18
Nut, Speed, .3125 Dia.
Spring Lever, Shift
Bracket, Shift Spacer
Shift Rod, Lower
Lens
Nut, Hex Lock, Nylon, #10-24, Gr2
Chute Control Assembly, 4-Way (Inc.
Cables & Control Head, not shown)
Bracket, Joystick
Screw, 1/4-20 x .375
Screw, Self-tapping, 1/4-20 x 1.750
Screw, Machine, #10-24 x 1.375
Rod, Pivot
Ferrule, 5/16-18 x .312
Nut, Flange Lock, Nylon, 1/4-20
Nut, Shoulder, Hex, 1/4-20,
Pin, Cotter, .072 Dia. x 1.13
Grip, 1.0 ID x 5.0
Knob, Shift
Lamp
Harness, Headlight
Socket, Lamp
Tie, Cable, 19 x 8.39”, Tree Mount
Plate, Lock
Cam, Clutch Lock
Spring, Compression, .39 x .60 x .88
Spring, Clutch, Lock
Spring, Torsion, 0.8156 ID x .3038
Bumper, Rubber, .62 OD x .22
Washer, Flat, .385 x .870 x .092
Screw, Shoulder, .437 x 1.345, 1/4-20
10 711-04287
11 711-0677
12 712-04064
13 712-04081A
14 714-0104
15 720-0274
16 720-04039
17 725-04213
18 725-04214
19 725-1649
20 726-0470
21 731-04894
22 731-04896
23 732-0193
24 732-04219
25 732-04238
26 735-0199A
27 736-0262
28 738-04122
50 790-00131
51 710-04187
52 712-04082
53 738-04133
54 753-04864
55 753-04866
56 753-04863
57 736-0463
Screw, 1/4-15 x .50
Nut, Hex Lock, 1/4-20
Bolt, Shoulder, 5/16 x 1.7, 1/4-20
Kit, Chute Control Housing
Kit, Lever Tube
Kit. 4-Way Knob
Washer, Flat, .25 x .630 x .051
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Style Q
37
27
7
7
40
36
39
38
28
31
29
26
70
33
1
17
9
23
41
13
3
69
32
19
15
34
5
43
25
7
30
9
18
14
24
12
22
71
6
9
4
2
8
4
6
51
35
7
7
45
64
59
53
60
58
67
55
66
56
63
57
65
49
68
62
42
48
54
61
20
46*
50
47
48
44
10
21
52
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Style Q
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Removal Tool, Snow
DESCRIPTION
Cable Guide, Chute Tilt
Support Tube, Chute
Cable Bracket (Cables not included)
Tab, Handle
Gearbox Assembly, Auger, 26” w/ Fitting
Gearbox Assembly, Auger, 28” w/ Fitting
Housing Assembly, Auger 26”
Housing Assembly, Auger 28”
Spiral Assembly, LH
731-2643
684-04057
710-0347
710-0451
710-0703
710-0726
712-04063
712-04064
712-04065
38 731-1313C
39 749-04155
40 784-5594
41 784-5599
42 618-04192
618-04193
Impeller Assembly, 12” Dia
Screw, 3/8-16 x 1.75, Gr5, Std
Bolt, Carriage, 5/16-18 x.750 Gr1
Screw, Carriage, 1/4-20 x .75, Gr5
Screw, 5/16-12 x 0.750
Nut, Flange Lock, Nylon, 5/16-18, GrF
Nut, Flange Lock, Nylon, 1/4-20, GrF
Nut, Flange Lock, Nylon, 3/8-16, GrF
Pin, Cotter, 3/32 x .750
Cable, Tie, 3/16 x .05 x 7.4
Nut, Push-on, .25 Dia
Chute, Adapter 5” Dia
Spring, Extension, .38 OD x 3.6
Washer, Wave, .625 x.885 x.015
Washer, Flat, .25 x .630 x .0515
Keeper, Flange
Screw, Shoulder, .498 x .340, 3/8-16
Screw, Shoulder, .625 x .17, 3/8-16
Pin, Shear, .25 x1.50, Gr2
Bearing, Hex Flange x .75 ID
Bearing, Ball, .75 ID x 1.85 OD
Pulley, Idler, Flat 2.75 OD
Housing, Bearing, 1.85 ID
Bracket, Auger Idler w/ Brake
Chute Assembly, Lower, 4-way
(Inc. Ref 17, Qty. 3)
Control Head (Inc. 4-Way Chute Control
Ass’y, not shown)
Bolt, Carriage, 5/16-18, 1.50, Gr2
Bolt, Carriage, 5/16-18, 1.00
Screw, 5/16-12 x 0.75
Screw, 1/4-15 x 0.75
Screw, Self-tapping 5/16-18 x 1.75
Pin, Clevis, 3/8 x 1.75
Auger Clutch Cable, 44.75”
Shoe, Slid
Pin, Cotter, .072 Dia. x 1.13
Upper Chute, Remote
43 684-04078
684-04079
8
9
44 684-04107
45 684-04108
46 731-04870
47 736-0188
48 737-3000
49 721-0179
50 741-0493A
51 790-00121
52 790-00138
53 719-0319
54 618-0418
10 714-0507
11 725-0157
12 726-04012
13 731-04705
14 732-0611
15 736-0174
16 736-0463
17 731-04869
18 738-0143
19 738-0281
20 738-04124
21 741-0245
22 741-0309
23 756-0981A
24 790-00075
25 790-00080
26 631-04132
Spiral Assembly, RH
Spacer, 1.25 OD x .75 ID x 1.00
Washer, Flat, .76 x 1.49 x .06
Lube Fitting, 3/16
Seal, Oil, .750 ID
Bushing, Flange, .800 ID x .910 OD
Plate, Shave, 2.25 x 25.66
Housing, Bearing, 1” Hex
Housing, Auger, RH Reducer
Housing Assembly, Auger, LH Reducer
(Inc. Refs. 49 & 55)
Bearing, Flange, .75 ID x 1.00 OD x .975
Gear, Worm 20T
Washer, Flat, .760 ID x 1.5 OD
Key, Hi-pro 3/16 x 5/8
55 741-0661A
56 717-0528A
57 736-0351
58 714-0161
59 715-04021
60 721-0325
61 711-04284
711-04283
62 710-0642
63 741-0662
64 717-04126
65 718-04071
66 721-0327
67 736-3084
68 741-0663
69 731-2635
70 629-0071
71 736-0242
Pin, Dowel, .25 OD x 1.2
Plug, 1/4 x .437
Axle, Auger, 26"
27 684-04116
Axle, Auger, 28"
Screw, Self-tapping, 1/4-20, 0.750
Bearing, Flange, .75 ID x 1.00 OD x .59
Shaft, Worm .75 OD
Collar, Thrust
Seal, Oil, .75 x 1 x .131
Washer, Flat, .51 x 1.12
Bearing, Flange, .75 ID x 1.00 OD x .925
Mount, Clean Out Tool
Extension Cord, 3-Prong
Washer, Bell, .340 x 872 x .060
28 710-0262
29 710-04071
30 710-0726
31 710-0895
32 710-0909A
33 711-0415
34 746-0897
35 790-00091
36 714-0104
37 731-04427
* Two found between spirals on Storm model 8526
* Three found between spirals on Storm model 9528.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Style Q
17
62
58
55
41
46
60
50
7
9
58
53
61
7
57
47
52
49
40
59
54
56
44
45
51
43
48
9
39
21
7
20
24
30
6
24
13
29
16
18
36
27
12
1
14
15
34
2
28
35
26
24
14
9
4
3
10
22
33
19
32
23
11
5
42
8
20
7
31
9
9
37
25
28
38
4
9
63
68
67
65
64
66
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Style Q
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Gear Assembly, 16/44T
Gear Assembly, 16/44T
Disc Assembly, Friction Wheel, .375
Wheel Assembly, Friction, 4.9 OD
Support Bracket Ass’y, Friction Wheel
Shift Assembly, Rod
Screw, 5/16-24 x .750, Gr5
Screw, 1/4-20 x 1.000
DESCRIPTION
Guide Bracket, Auger Cable
Frame
Guide Bracket, Front, Auger Cable
Cover, Frame
Roller Bracket, Drive Cable
Screw, 3/8-24 x 1.25, Gr8
Screw, 1/4-20 x 1.00, Gr5
Screw, Sems, 3/8-16 x 1.00
Screw, 5/16-24 x .875, Gr8
Nut, Flange Lock, Nylon, 1/4-20, GrF
Cover, Belt
Spring, Extension, .38 OD x 2.68
Washer, Flat, .406 x 1.25 x.157
Washer, Flat, .34 x 1.50 x .150
Bearing, Ball, 20 x 47 x 14
Shoulder Spacer
Pulley, Adapter, .75 Dia.
Spacer, .777 OD x .260 ID x.550
Spacer, .875 ID x 1.185 OD
V-Belt, 1/2”
V-Belt, 3/8”
Pulley, Auger, 8.1 x .50
Pulley, Half, 2.600 OD
Pulley, Half, 2.2 OD
Washer, Bearing, 2.12 OD x .255 ID
Idler, Bracket, Drive
Screw, #10-16 x .75
617-04026
617-04025
656-0012A
684-04066
684-04045
684-04139
710-0627
710-0788
710-1652
35 784-5687A
36 790-00072
37 790-00096
38 790-00054
39 790-00055
40 710-0191
41 710-0597
42 710-0654A
43 710-1245B
44 712-04064
45 731-04792
46 732-0710
47 736-0247
48 736-0505
49 741-0919
50 748-0234
51 748-04053
52 750-04230
53 750-04303
54 754-04050
55 754-0456
56 756-04109
57 756-04113
58 756-04114
59 790-00062
60 790-00082
61 710-04082
62 712-3004A
63 618-04169
64 718-04070
65 735-0243B
66 790-00010
67 790-00011
68 710-0896
8
9
Screw, 1/4-20 x .625
10 711-04246A Hex Shaft, Drive, .75
11 712-0711
12 714-0161
13 716-0231
14 716-0136
15 717-04129a Pinion, 16T
16 717-04137a Gear, 44T
Nut, Jam, 3/8-24, Gr2
Key, Hi-pro 3/16 x 5/8
Ring, E Type, .750
Ring, E-Type, .875
17 684-04014A Shroud Assembly, Troy-Bilt
18 726-0221
19 732-0264
20 736-0242
21 736-04161
22 736-0300
23 736-0105
24 736-0287
25 634-04147
634-04148
Nut, Speed, .500
Extension Spring
Washer, Bell, .340 x .872 x .060
Washer, Flat, .75 x 1.00 x .060
Washer, Flat, .406 x .875 x .059
Washer, Bell, .375 x .870 x .063
Washer, Flat, .793 x 1.24 x .060
Wheel, Complete, 15 x 5 x 6, LH
Wheel, Complete,15 x 5 x 6, RH
Spacer, 1.25 OD x .75 ID x 3.00
26 731-04873
27 738-04095A Axle, .75 x 22
Nut, Flange Lock, 5/16-18, Gr5
Bearing Assembly, Friction Wheel
Hub, Friction Wheel
Friction Wheel Rubber, 4.875 OD
Plate, Friction, 12 Pt 4.60 Dia
Plate, Friction, Extrs, 12 Pt 4.60 Dia
Screw, Self-tapping, 1/4-14 x 0.625
28 738-0924
29 741-0563
30 741-0245
31 746-0897
32 746-04086
33 748-0190
34 756-0625
Screw, 1/4-28 x .375
Bearing, Ball, 17 x 40 x 12
Bearing, Hex Flange x .75 ID
Cable, Auger, 44.75
Cable, Drive, 41.75
Spacer, .508 ID x .75 OD x .68
Roller, Cable
Wheel Assembly
Complete
Wheel Size
Rim Only
Tire Only
Air Valve
634-04147
634-04148
15 x 5
15 x 5
634-04151
634-04151
734-04012
734-04012
734-0255
734-0255
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by Troy-Bilt LLC
with respect to new merchandise purchased and used in the
United States and/or its territories and possessions, and by
MTD Products Limited with respect to new merchandise
purchased and used in Canada and/or its territories and
possessions (either entity respectively, “Troy-Bilt”).
deterioration of the exterior finish due to use or
exposure.
Service completed by someone other than an
authorized service dealer.
d.
e.
Troy-Bilt does not extend any warranty for products
sold or exported outside of the United States and/or
Canada, and their respective possessions and
territories, except those sold through Troy-Bilt’s
authorized channels of export distribution.
Replacement parts that are not genuine Troy-Bilt parts.
Transportation charges and service calls.
If Products are used commercially. (Troy-Bilt may
separately offer Limited Commercial Warranties on
certain select products. Ask your dealer or retailer for
details or contact Troy-Bilt Service for more
information.)
“Troy-Bilt” warrants this product (excluding its normal wear
parts as described below) against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
materials or workmanship. This limited warranty shall only
apply if this product has been operated and maintained in
accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not
approved by Troy-Bilt for use with the product(s) covered by
this manual will void your warranty as to any resulting
damage.
f.
g.
h.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind Troy-Bilt. During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
Normal wear parts are warranted to be free from defects in
material and workmanship for a period of thirty (30) days from
the date of purchase. Normal wear parts include, but are not
limited to items such as: batteries, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow thrower
skid shoes, friction wheels, shave plates, auger spiral rubber
and tires.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. Troy-Bilt
shall not be liable for incidental or consequential loss or
damage including, without limitation, expenses incurred
for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted
product.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area:
In the U.S.A.
Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
Check your Yellow Pages, or contact Troy-Bilt LLC at P.O.
Box 361131, Cleveland, Ohio 44136-0019, or call 1-866-840-
6483 or 1-330-558-7220, or log on to our Web site at
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or
call 1-800-668-1238 or log on to our Web site at
This limited warranty does not provide coverage in the
following cases:
This limited warranty shall not extend to anyone other than
the original purchaser or to the person for whom it was
purchased as a gift.
a.
The engine or component parts thereof. These items
may carry a separate manufacturer’s warranty. Refer
to applicable manufacturer’s warranty for terms and
conditions.
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may
also have other rights that vary in different jurisdictions.
b.
c.
Log splitter pumps, valves, and cylinders have a
separate one- year warranty.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
IMPORTANT: Owner must present Original Proof of
Purchase to obtain warranty coverage.
Troy-Bilt LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-7220
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
Download from Www.Somanuals.com. All Manuals Search And Download.
|