Trane Heating System TSC060 120 50 Hz User Manual

Packaged Cooling with  
Electric Heat Rooftop Units  
Precedent™  
TSC060-120  
50 Hz  
RT-PRC016-EN  
November 2003  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Introduction  
2
4
Features and Benefits  
Application Considerations  
Selection Procedure  
Model Number Description  
General Data  
9
10  
12  
13  
14  
33  
34  
35  
36  
44  
45  
Performance Data  
Zone Controls  
Electrical Data  
Jobsite Connections  
Dimensional Data  
Weights  
Mechanical Specifications  
RT-PRC016-EN  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features and  
Benefits  
Easy Access Panels  
Remove two screws for access to the  
standardized internal components and  
wiring.  
Easy-Adjust Idler Arm  
With the Easy-Adjust Idler Arm, the belt  
and sheaves can be quickly adjusted  
without moving the mounted fan motor.  
The result is a major savings in time and  
money.  
Patented Condenser Coil  
Precedent boasts a patented 1+1+1  
Hybrid coil, permanently gapped for  
easy of cleaning.  
Unit Cabinet  
The compact cabinet with rounded  
corners takes up less room and is less  
costly to ship. The beveled and ribbed  
top is not only aesthetically pleasing, it is  
designed to prevent water from pooling.  
Single Point Power  
A single electrical connection powers the  
unit.  
Colored And Numbered Wiring  
You save time and money tracing wires  
and diagnosing the unit.  
Convertible Units  
The units ship in a downflow  
configuration. They can be easily  
converted to horizontal by simply  
moving two panels.  
Sloped Drain Pans  
Every Precedent unit has a non-  
corrosive, removable, double-sloped  
drain pan thats easy to clean and  
reversible to allow installation of drain  
trap on either side of the unit.  
Units come complete with horizontal  
duct flanges so the contractor doesnt  
have to field fabricate them. These  
duct flanges are a time and cost saver.  
Compressors  
Through the Base Condensate  
Every unit includes provisions for  
through the base condensate drain  
connections. This allows the drain to be  
connected through the roof curb instead  
of a roof penetration.  
Precedentcontains the best  
compressor technology available to  
achieve the highest possible  
performance. Our compressor line  
includes Trane built reciprocating and  
scrolls.  
Foil-Faced Insulation  
Easy Access Panels  
All panels in the Evaporator section of  
the unit have cleanable foil-faced  
insulation. All edges are either captured  
or sealed to ensure no fibers get into the  
airstream.  
Easy access panels reduce the number of  
possible water entry points.  
Low Ambient Cooling  
All Precedent units have cooling  
capabilities down to 0°F as standard.  
Unit Base  
For added water integrity, Precedent has  
a raised 29 mm (1 1/8") lip around the  
units downflow supply and return to  
prevent water from blowing into the  
ductwork.  
RT-PRC016-EN  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features and  
Benefits  
Flexible Applications  
Standardized Components  
• Only two roof curbs for the 5-10 ton  
Precedent line. . .simplifies curb  
RseelleiacTtieolnm. icroprocessor controls to  
meet either the simple or the more  
complex application.  
Components are placed in the same  
location on all Precedentunits.  
Familiarize yourself with one Precedent  
and you are familiar with every  
Precedent.  
• Airflow is outstanding. The Precedent  
can replace an older machine with old  
ductwork and, in many cases, improve  
comfort through better air distribution.  
• Belt drive — standard or oversized  
supply fan motors meet a wide airflow  
range.  
• Precedent offers ultimate flexibility.  
Options and components are not pre-  
packaged at the factory. Units are built  
to order in our standard “shortest in  
the industry” ship cycle time.  
Easy Access Low Voltage Terminal  
Board  
Precedents Low Voltage Terminal Board  
is external to the electrical control  
cabinet. It is extremely easy to locate and  
attach the thermostat wire. This is  
another cost and time saving installation  
feature.  
Low Voltage Connections  
The wiring of the low voltage  
connections to the unit and the zone  
sensors is as simple as 1-1, 2-2, and 3-3.  
This simplified system makes it easy for  
the installer to wire  
Single-Side Service  
Single-side service is standard on all  
Precedent units.  
RT-PRC016-EN  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features and  
Benefits  
• Eliminates the need for field-installed  
components with its built-in anti-  
short-cycle timer, time delay relay  
and minimum on time controls.  
These controls are factory tested to  
assure proper operation.  
• Requires no special tools to run the  
Precedent unit through its paces  
during testing. Simply place a  
jumper between Test 1 and Test 2  
terminals on the Low Voltage  
Terminal Board and the unit will walk  
through its operational steps. The  
unit automatically returns control to  
the zone sensor after stepping  
through the test mode a single time,  
even if the jumper is left on the unit.  
Micro Controls  
Several years ago,Trane was the first to  
introduce microprocessor controls into  
the Light Commercial Market. That  
design, along with immeasurable  
experience, has provided the  
technology for Tranes second-  
generation ReliaTelmicroprocessor  
controls.  
• As long as the unit has power and  
the LED is lit, the Micro is  
operational. The light indicates that  
the Micro is functioning properly.  
• Features expanded diagnostic  
capabilities when used with Tranes  
Integrated Comfort Systems.  
• As an energy benefit, softens  
electrical spikesby staging on fans,  
compressors and heaters.  
ReliaTelMicro:  
• Provides unit control for heating,  
cooling, and ventilating by utilizing  
input from sensors that measure  
outdoor and indoor temperature.  
• The Intelligent Fallback or Adaptive  
Control is a benefit to the building  
occupant. If a component goes  
astray, the unit will continue to  
operate at predetermined  
Improves quality and reliability  
through the use of time-tested  
microprocessor controls and logic.  
temperature set points.  
Intelligent Anticipation is a standard  
feature of the Micro. Functioning  
constantly, the Micro and zone  
• Prevents the unit from short cycling,  
considerably improving compressor  
life.  
sensors work together in harmony,  
to provide tight comfort control.  
• Ensures that the compressor will run  
for a specific amount of time, which  
allows oil to return for better  
lubrication, enhancing the reliability of  
the compressor.  
• Reduces the number of components  
required to operate the unit, thereby  
reducing possibilities for component  
failure.  
RT-PRC016-EN  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features and  
Benefits  
Factory-installed Options  
Hinged Access Doors  
The following options round-out the  
complete line of Precedentoptions:  
These doors permit easy access to the  
filter, fan/heat, and compressor/control  
sections. They reduce the potential roof  
damage from screws or sharp access  
door corners.  
— 0 - 50% Manual or Motorized  
Outside Air  
— Hail Protection Quality Coil Guards  
— Electric Heaters (available as field  
installed accessories)  
Economizer  
— Discharge Air Sensor  
Equipped with either dry bulb, reference  
or comparative enthalpy sensing, this  
feature provides free cooling as the  
outdoor temperature and/or humidity  
decreases. Economizers, correctly  
installed, offer a valuable energy  
savings. Factory-installed economizers  
save time and ensure proper installation.  
— Wide array of Zone Sensors and  
Thermostats  
— Factory built Roof Curb  
One of Our Finest Assets:  
Trane Sales Representatives are a  
Support group that can assist you with:  
— Product  
— Application  
— Service  
Training  
— Special Applications  
— Specifications  
Clogged Filter/Fan Fail Switches  
These sensors allow a zone sensor  
service light or Integrated Comfort  
System to indicate a dirty filter or a fan  
thats not working. The field installation  
charges for these valuable feedback  
devices often eliminate them from  
consideration. Factory installation can  
make such features a good investment.  
— Computer Programs and much more  
Precedent has the features and benefits  
that make it first class in the light  
commercial rooftop market. Designed  
with input from field contractors and  
engineers, its airflow performance is  
outstanding.  
Comm-3/4 Trane Communication  
Interface  
Available factory or field-installed. This  
module when applied with ReliaTel™  
easily interfaces with Tranes Integrated  
ComfortSystem.  
Precedent…The same Trane  
quality…with added flexibility.  
RT-PRC016-EN  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features and  
Benefits  
Quality And Reliability Testing  
• We perform a 100% coil leak test at the  
factory. The evaporator and condenser  
coils are leak tested at 1375 kPa (200  
psig) and pressure tested to 3100 kPa  
(450 psig).  
All Precedentdesigns were rigorously  
rain tested at the factory to ensure  
water integrity.  
• Actual shipping tests were performed  
to determine packaging requirements.  
Units were test shipped around the  
country to determine the best  
packaging.  
• All parts are inspected at the point of  
final assembly. Sub-standard parts are  
identified and rejected immediately.  
• Every unit receives a 100% unit run test  
before leaving the production line to  
make sure it lives up to rigorous Trane  
requirements.  
• Factory shake and drop tests were  
used as part of the package design  
process to help assure that the unit  
arrives at the job site in top condition.  
We test designs at our factory not on  
our customers!  
• Rigging tests include lifting a unit into  
the air and letting it drop one foot,  
assuring that the lifting lugs and rails  
hold up under stress.  
VariTrac™  
VariTrac  
When Tranes changeover VAV System  
for light commercial applications is  
coupled with Precedent, it provides the  
latest in technological advances for  
comfort management systems and can  
allow thermostat control in every zone  
served by VariTrac.  
RT-PRC016-EN  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Application  
Considerations  
Application of this product should be  
within the cataloged airflow and cooling  
considerations.  
Condensate Trap  
The evaporator is a draw-thru  
configuration. A trap must be field  
provided prior to start-up on the cooling  
cycle.  
Low Ambient Cooling  
The Precedentline features, with  
ReliaTelmicroprocessor controls, low  
ambient cooling down to 18°C (0°F).  
Contact your local Trane Representative  
for more assistance with low ambient  
cooling applications.  
Clearance Requirements  
The recommended clearances identified  
with unit dimensions should be  
maintained to assure adequate service  
maximum capacity and peak operating  
efficiency. Actual clearances which  
appear inadequate should be reviewed  
with the localTrane sales personnel.  
Barometric Relief  
This product line offers an optional  
barometric relief damper. for use in  
conjunction with economizer option.  
This accessory consists of gravity  
dampers which open with increased  
pressure. As the building air pressure  
increases, the pressure in the unit return  
air section also increases, opening the  
dampers and relieving the conditioned  
space.  
Unit Pitch  
These units have reversible sloped  
condensate drain pans. Units must be  
installed level, any unit slope must be  
toward the side of unit where  
condensate drain is connected.  
NOTE: THE EFFECTIVENESS OF  
BAROMETRIC RELIEF DAMPER  
DURING ECONOMIZING OPERATION  
IS SYSTEM RELATED.  
PRESSURE DROP OF THE RETURN AIR  
SYSTEM SHOULD BE CONSIDERED TO  
CONTROL BUILDING PRESSURIZA-  
TION.  
RT-PRC016-EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selection  
Procedure - SI Units  
Cooling Capacity  
Step 3  
Heating Capacity  
In order to select the correct unit which  
meets the buildings requirements, the  
fan motor heat must be deducted from  
the gross cooling capacity.The amount  
of heat that the fan motor generates is  
dependent on the effort by the motor -  
cfm and static pressure.To determine  
the total unit static pressure:  
Step 1  
Step 1  
Calculate the buildings total and sensible  
cooling loads at design conditions. Use  
the Trane calculation methods or any  
other standard accepted method.  
Calculate the building heating load using  
the Trane calculation form or other  
standard accepted method.  
Step 2  
Factors used in unit selection:  
Size the system heating capacity to  
match the calculated building heating  
load. The following are building heating  
requirements:  
A
Total Cooling Load: 16.7 kW  
External Static (duct system)  
110 Pa  
B
A
Sensible Cooling Load: 11.7 kW  
Standard Filter 1 in.  
from Table PD-21  
37 Pa  
Total heating load of 5 kW  
C
B
Airflow: 3400 m3/h  
Economizer  
5 Pa  
2000 cfm  
D
(100% Return Air)  
Table PD-21  
from  
C
Electrical Characteristics: 380-415/50/3  
380 volt/3 phase Power Supply  
E
Electric Heater Size 7.5 kW  
from Table PD-21  
17 Pa  
The electric heat accessory capacities are  
listed in Table PD-23. From the table, the  
smallest heater will deliver 7.5 kW at  
380 V. Referring to Table ED-2, the  
electric heater selection is  
Summer Design Conditions: Entering  
Evaporator Coil: 27 DB, 19 WB Outdoor  
Ambient: 35  
Total Static Pressure  
169 Pa  
Note: The Evaporator Fan Performance  
Table PD-6 has deducted the pressure  
drop for a 25 mm filter already in the  
unit (see note below Table PD-6).  
Therefore, the actual total static pressure  
is 169-17 (from Table PD-21) = 152 Pa.  
With 3400 m3/h and 152 Pa  
Table PD-6 shows .67 kW for this unit.  
Note below the table gives a formula to  
calculate Fan Motor Heat,  
Fan Motor Heat (kw) =  
1.144 x (Fan kW) + 0.132  
F
External Static Pressure: 110 Pa  
BAYHTRR412A.  
Air Delivery Selection  
Step 2  
External static pressure drop through the  
air distribution system has been  
calculated to be 110 Pa. From Table PD-  
21 static pressure drop through the  
economizer is 5 Pa and the 7.5 kW heater  
is 17 Pa (110 + 5 + 17). EnterTable PD-6  
for a TSC060AD at 3400 m3/h and 132 Pa  
static pressure. The standard motor will  
give the desired airflow at a rated kW of  
0.64.  
Table PD-1 shows that a TSC060AD has a  
gross cooling capacity of 17.8 kW and  
14.4 kW sensible capacity at 3400 m3/h  
and 35 DB outdoor ambient with 27 DB,  
19 WB air entering the evaporator.  
To Find Capacity at Intermediate  
Conditions Not in the Table  
When the design conditions are between  
two numbers that are in the capacity  
table, interpolation is required to  
approximate the capacity. Note:  
Extrapolation outside of the table  
conditions is not recommended.  
= 1.144 x 0.67 + 0.132 = 0.90 kW  
Now subtract the fan motor heat from  
the gross cooling capacity of the unit:  
Net Total Cooling Capacity  
Accessory Selection  
Select accessories needed to  
accommodate the application.  
= 17.8 kW - 0.9 = 16.9 kW.  
Net Sensible Cooling Capacity  
= 14.4 kW - 0.9 = 13.5 kW.  
Step 4  
If the performance will not meet the  
required load of the buildings total or  
sensible cooling load, try a selection at  
the next higher size unit.  
RT-PRC016-EN  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selection  
Procedure - IP Units  
Step 3  
Heating Capacity  
Cooling Capacity  
In order to select the correct unit which  
meets the buildings requirements, the  
fan motor heat must be deducted from  
the gross cooling capacity.The amount  
of heat that the fan motor generates is  
dependent on the effort by the motor -  
cfm and static pressure. To determine  
the total unit static pressure:  
Step 1  
Step 1  
Calculate the building heating load using  
the Trane calculation form or other  
standard accepted method.  
Calculate the buildings total and sensible  
cooling loads at design conditions. Use  
the Trane calculation methods or any  
other standard accepted method.  
Step 2  
Size the system heating capacity to  
match the calculated building heating  
load. The following are building heating  
requirements:  
Factors used in unit selection:  
A
Total Cooling Load: 59 MBh  
External Static (duct system)  
0.45 wg  
B
A
Sensible Cooling Load: 40 MBh  
Standard Filter 1 in.  
from Table PD-21a  
0.15 wg  
Total heating load of 15 MBH  
C
B
Airflow: 2000 cfm  
Economizer  
0.02 wg  
from  
2000 cfm  
D
(100% Return Air)  
Table PD-21a  
C
Electrical Characteristics: 380-415/50/3  
380 volt/3 phase Power Supply  
E
Electric Heater Size 26 MBh  
from Table PD-21a  
0.07 wg  
The electric heat accessory capacities are  
listed in Table PD-23a. From the table,  
the smallest heater will deliver 26 MBh at  
380 volts. Referring to Table ED-2, the  
electric heater accessory selection is  
BAYHTRR412A.  
Summer Design Conditions: Entering  
Evaporator Coil: 80 DB, 67 WB Outdoor  
Ambient: 95  
Total Static Pressure  
0.69 wg  
Note: The Evaporator Fan Performance  
Table PD-6a has deducted the pressure  
drop for a 1 in. filter already in the unit  
(see note below Table PD-6a). Therefore,  
the actual total static pressure is 0.69 -  
0.15 (from Table PD-21a) = 0.50 wg.  
F
External Static Pressure: 0.45 in. wg  
Step 2  
Air Delivery Selection  
Table PD-1a shows that a TSC060AD has  
a gross cooling capacity of 62.0 MBh and  
46.4 MBh sensible capacity at 2000 cfm  
and 95 DB outdoor ambient with 80 DB,  
67 WB air entering the evaporator.  
External static pressure drop through the  
air distribution system has been  
calculated to be 0.45 inches of water.  
From Table PD-21a static pressure drop  
through the economizer is 0.02 and the  
26 kW heater is 0.07 inches of water (0.45  
+ 0.02 + 0.07). EnterTable PD-6a for a  
TSC060AD at 2000 cfm and 0.54 static  
pressure. The standard motor will give  
the desired airflow at a rated bhp of  
about 1.01.  
With 2000 cfm and 0.50 wg.  
Table PD-6a shows .83 bhp for this unit.  
Note below the table gives a formula to  
calculate Fan Motor Heat,  
Fan Motor Heat (MBh) =  
2.915 x (Fan BHP) + 0.451  
To Find Capacity at Intermediate  
Conditions Not in the Table  
When the design conditions are between  
two numbers that are in the capacity  
table, interpolation is required to  
approximate the capacity. Note:  
Extrapolation outside of the table  
conditions is not recommended.  
= 2.915 x 0.83 + 0.451 = 2.87 MBh  
Now subtract the fan motor heat from  
the gross cooling capacity of the unit:  
Net Total Cooling Capacity  
Accessory Selection  
Select accessories needed to  
accommodate the application.  
= 62 MBh - 2.87 = 59.1 MBh.  
Net Sensible Cooling Capacity  
= 46.4 MBh - 2.87 = 43.5 MBh.  
Step 5  
If the performance will not meet the  
required load of the buildings total or  
sensible cooling load, try a selection at  
the next higher size unit.  
RT-PRC016-EN  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model  
Num ber  
Description  
T
1
S
2
C
060  
A
D
8
R
9
O
A
**  
C
0
0
0
0
0
0
0
0
0
0
1
3 4,5,6 7  
10 11 12,13 14 15 16 17 18 19 20 21 22 23 24 25  
Digit 1 - Unit Function  
= DX Cooling  
Digit 14 - Fresh Air Selection  
0 = No Fresh Air  
Digit 18 - Through the Base Provisions  
0 = No Through the Base Provisions  
T
A = Manual Outside Air Damper 0-50%  
B = Motorized Outside Air Damper 0-50%  
C = Economizer, Dry Bulb 0-100%  
without Barometric Relief  
D = Economizer, Dry Bulb 0-100%  
with Barometric Relief  
E = Economizer, Reference Enthalpy  
0-100% without Barometric Relief  
F = Economizer, Reference Enthalpy  
0-100% with Barometric Relief  
G = Economizer, Comparative Enthalpy  
0-100% without Barometric Relief  
H = Economizer, Comparative Enthalpy  
0-100% with Barometric Relief  
Digit 2 - Efficiency  
= Standard Efficiency  
Digit 19 - Disconnect/Circuit Breaker  
0 = No Disconnect or Circuit Breaker  
S
Digit 3 - Airflow  
C = Convertible  
Digit 20 - Convenience Outlet  
0 = No Convenience Outlet  
Digits 4,5,6 - Nominal Gross Cooling  
Capacity (MBh)  
Digit 21 - Communications Options  
0 = No Communications Interface  
1 = Comm-3/4 Communications Interface  
2 = Comm-5 Communications Interface  
kW  
060 = 17.6  
072 = 21.1  
090 = 26.4  
102 = 29.9  
120 = 35.1  
Tons  
5
6
7.5  
8.5  
10  
Digit 22 - Refrigeration System Option  
0 = Standard Refrigeration System  
Digit 23 - Refrigeration Controls  
0 = No Refrigeration Control  
Digit 7 - Major Design Sequence  
A = First  
Digit 15 - Supply Fan/Drive Type/Motor  
0 = Standard Drive  
1 = Oversized Motor  
Digit 24 - Smoke Detector  
0 = No Smoke Detector  
Digit 8 - Unit Voltage  
D = 380-415/50/3  
Digit 25 - Monitoring Controls  
0 = No Monitoring Control  
1 = Clogged Filter Switch  
2 = Fan Failure Switch  
3 = Discharge Air Sensing Tube  
4 = Clogged Filter Switch and Fan Fail  
Switch  
5 = Clogged Filter Switch and Discharge  
Air Sensing Tube  
6 = Fan Fail Switch and Discharge Air  
Sensing Tube  
Digit 16 - Hinged Service Access/Filters  
0 = Standard Panels/Standard Filters  
A = Hinged Access Panels/Standard Filters  
B = Standard Panels/  
50 mm (2”) Pleated Filters  
C = Hinged Access Panels/  
Digit 9 - Unit Controls  
R = ReliaTelMicroprocessor  
Digit 10 - Heating Capacity  
0 = No Electric Heat  
Digit 11 - Minor Design Sequence  
A = First Sequence  
50 mm (2”) Pleated Filters  
Digit 17 - Condenser Coil Protection  
0 = Standard Coil  
1 = Standard Coil with Hail Guard  
2 = Epoxy Coated Condenser Coil  
3 = Epoxy Coated Condenser Coil with  
Hail Guard  
Digits 12, 13 - Service Sequence  
**= Factory Assigned  
7 = Clogged Filter and Fan Fail Switches  
and Discharge Air Sensing Tube  
RT-PRC016-EN  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
General  
Data  
Table GD - 1 — General Data  
Convertible Units  
Convertible Units  
Convertible Units  
TSC090AD  
Convertible Units  
TSC102AD  
Convertible Units  
TSC120AD  
TSC060AD  
TSC072AD  
Cooling Performance 1  
Gross Capacity - kW (MBh)  
COP (EER)2  
Nominal Airflow - m3/h (cfm)  
Rated Airflow - m3/h (cfm)  
Net Capacity - kW (MBh)  
System Power - kW  
18.2 (62.0)  
2.99 (10.2)  
3400 (2000)  
3400 (2000)  
17.3 (59.0)  
5.78  
23.2 (79.0)  
3.08 (10.5)  
4080 (2400)  
3570 (2100)  
22.0 (75.0)  
7.14  
26.7 (91.0)  
3.02 (10.3)  
5100 (3000)  
4460 (2625)  
25.2 (86.0)  
8.35  
31.1 (106.0)  
3.02 (10.3)  
5780 (3400)  
5100 (3000)  
29.9 (102.0)  
9.90  
34.9 (119.0)  
2.99 (10.2)  
6800 (4000)  
5950 (3500)  
33.1 (113.0)  
11.08  
Compressor  
Number -Type  
Outdoor Sound Rating - dB 3  
Outdoor Coil -Type  
1-Climatuff Scroll  
80  
1-Trane 3-D Scroll  
85  
1-Trane 3-D Scroll  
85  
2-Climatuff Scroll  
83  
2-Climatuff Scroll  
79  
Lanced  
Lanced  
Lanced  
Lanced  
Lanced  
Tube Size - in. OD  
Face Area - m2 (sq ft)  
Rows / FPI  
0.3125  
1.02 (10.96)  
3 / 17  
0.3125  
1.29 (13.88)  
2 / 17  
0.3125  
1.29 (13.88)  
2 / 17  
0.3125  
1.75 (18.89)  
2 / 17  
0.3125  
2.41 (25.92)  
2 / 17  
Indoor Coil -Type  
Lanced  
Lanced  
Lanced  
Lanced  
Lanced  
Tube Size OD - in.  
Face Area - m2 (sq ft)  
Rows / FPI  
0.3125  
0.62 (6.68)  
3 / 16  
0.3125  
0.92 (9.89)  
2 / 16  
0.3125  
0.92 (9.89)  
3 / 16  
0.3125  
1.15 (12.36)  
3 / 16  
0.3125  
1.15 (12.36)  
4 / 16  
Refrigerant Control  
Drain Connection No. / Size - in.  
Outdoor Fan -Type  
No. Used / Diameter - in.  
DriveType / No. Speeds  
CFM  
Short Orifice  
1 / 0.75 NPT  
Propeller  
1 / 22  
Direct / 1  
2900  
Short Orifice  
1 / 0.75 NPT  
Propeller  
1 / 26  
Direct / 1  
5100  
Short Orifice  
1 / 0.75 NPT  
Propeller  
1 / 26  
Direct / 1  
5200  
Short Orifice  
1 / 0.75 NPT  
Propeller  
1 / 26  
Direct / 1  
5500  
Short Orifice  
1 / 0.75 NPT  
Propeller  
1 / 26  
Direct / 1  
5800  
No. Motors / kW (HP)  
Motor RPM  
1 / 0.30 (0.40)  
950  
1 / .56 (0.75)  
950  
1 / .56 (0.75)  
950  
1 / .56 (0.75)  
950  
1 / .56 (0.75)  
950  
Belt Drive Indoor Fan -Type  
No. Used  
FC Centrifugal  
1
FC Centrifugal  
1
FC Centrifugal  
1
FC Centrifugal  
1
FC Centrifugal  
1
Fan Diameter x Width - mm (in.)  
DrvieType / No. Speeds  
No. Motors  
280 X 280 (11 x 11)  
Belt / Variable Speed  
1
305 X 305 (12 x 12)  
Belt / Variable Speed  
1
305 X 305 (12 x 12)  
Belt / Variable Speed  
1
381 X 381 (15 x 15)  
Belt / Variable Speed  
1
381 X 381 (15 x 15)  
Belt / Variable Speed  
1
Standard Motor Power - kW (HP)  
Oversized Motor Power - kW (HP)  
Motor RPM - Standard / Oversized  
Motor Frame Size  
1.1 (1.5)  
1.1 (1.5)  
1.5 (2.0)  
1450 / 1450  
56  
1.5 (2.0)  
2.2 (3.0)  
1450 / 2850  
56  
1.5 (2.0)  
2.2 (3.0)  
1450 / 2850  
56  
2.2 (3.0)  
-
-
1450 / -  
56  
2850 / -  
56  
Filters - Type Furnished  
(No.) Size Reccommended - mm  
(No.) Size Reccommended - in.  
Refrigerant Charge - kg (lbs) of R-22 4  
Throwaway  
(2) 508 X 762 X 25  
(2) 20 X 30 X 1  
3.7 (8.2)  
Throwaway  
(4) 406 X 635 X 50  
(4) 16 X 25 X 2  
3.7 (8.2)  
Throwaway  
(4) 406 X 635 X 50  
(4) 16 X 25 X 2  
4.5 (10.0)  
Throwaway  
(4) 508 X 635 X 50  
(4) 20 X 25 X 2  
Circuit 1 - 3.8 (8.3)  
Circuit 2 - 2.0 (4.4)  
Throwaway  
(4) 508 X 635 X 50  
(4) 20 X 25 X 2  
Circuit 1 - 3.4 (7.5)  
Circuit 2 - 3.3 (7.3)  
Notes:  
1. Cooling Perform ance is rated at 35.0 C (95 F) am bient, 26.7 C (80 F) entering dry bulb, 19.4 C (67 F) entering wet bulb. Gross capacity does not include the effect of fan m otor  
heat. Net capacity includes the effect of fan m otor heat. Units are suitable for operation to ± 20 % of nom inal airflow.  
2. EER are rated at ARI conditions.  
3. Outdoor Sound rating shown is tested in accordance with ARI Standard 270. For m ore inform ation refer to Perform ance Data Table "Sound Power Level".  
4. Refrigerant charge is an approcim ate value. For a m ore precise value, see unit nam eplate and service literature.  
RT-PRC016-EN  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-1 — Gross Cooling Capacities (kW) -TSC060AD - (SI)  
Ambient Temperature (C)  
Enter.  
Dry  
Bulb  
Temp  
(C)  
24  
27  
30  
33  
24  
27  
30  
33  
24  
27  
30  
33  
24  
30  
35  
40  
45  
19  
Entering Wet Bulb Temperature (C)  
19 22 16 19  
m3/h  
Airflow  
16  
19  
22  
16  
22  
16  
22  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
16.2 13.9 18.5 11.3 19.9 8.3 15.0 13.3 17.4 11.3 19.3 8.0 13.9 12.7 16.1 10.7 18.4 7.5 12.7 12.1 14.7 9.5 17.3 7.0  
16.7 16.7 18.6 14.1 20.0 11.1 15.8 15.8 17.4 13.6 19.4 10.8 14.8 14.8 16.1 13.0 18.5 10.3 13.8 13.8 14.7 12.3 17.3 9.8  
18.1 18.1 18.7 16.9 20.2 13.6 17.2 17.2 17.7 16.5 19.5 13.5 16.2 16.2 16.5 15.9 18.5 13.1 15.1 15.1 15.1 15.1 17.3 12.6  
19.3 19.3 19.2 19.2 20.3 16.2 18.5 18.5 18.5 18.5 19.6 16.1 17.6 17.6 17.6 17.6 18.7 15.9 16.6 16.6 16.6 16.6 17.5 15.4  
16.7 14.8 18.8 11.8 20.1 8.6 15.5 14.2 17.8 11.3 19.5 8.3 14.2 13.5 16.5 11.4 18.7 7.7 13.1 12.9 15.0 10.8 17.6 7.2  
17.5 17.5 18.9 14.9 20.2 11.4 16.5 16.5 17.8 14.4 19.6 11.2 15.4 15.4 16.5 13.8 18.8 10.8 14.4 14.4 15.1 13.1 17.6 10.3  
18.8 18.8 19.1 17.9 20.4 14.1 17.9 17.9 18.2 17.6 19.7 14.1 16.9 16.9 17.0 17.0 18.8 13.8 15.8 15.8 15.8 15.8 17.7 13.4  
19.8 19.8 19.8 19.8 20.6 16.8 19.2 19.2 19.2 19.2 19.9 16.9 18.3 18.3 18.3 18.3 19.0 16.8 17.4 17.4 17.4 17.4 17.9 16.4  
17.1 15.6 19.1 12.3 20.2 8.8 15.9 15.0 18.1 11.8 19.7 8.5 14.6 14.3 16.8 11.2 18.9 7.9 13.4 13.4 15.3 11.4 17.8 7.5  
18.1 18.1 19.2 15.5 20.4 11.6 17.1 17.1 18.2 15.1 19.8 11.5 16.0 16.0 16.9 14.6 19.0 11.3 14.9 14.9 15.4 13.9 17.9 10.8  
19.3 19.3 19.5 18.7 20.6 14.5 18.5 18.5 18.6 18.6 20.0 14.6 17.6 17.6 17.6 17.6 19.1 14.4 16.5 16.5 16.5 16.5 17.9 14.1  
20.2 20.2 20.2 20.2 20.8 17.4 19.6 19.6 19.6 19.6 20.2 17.6 18.9 18.9 18.9 18.9 19.3 17.6 18.0 18.0 18.0 18.0 18.3 17.4  
17.4 16.4 19.3 12.6 20.3 9.1 16.2 15.8 18.4 12.2 19.8 8.8 14.9 14.9 17.1 11.7 19.0 8.1 13.9 13.9 15.5 12.1 18.0 7.7  
18.6 18.6 19.4 16.1 20.5 12.3 17.7 17.7 18.4 15.8 19.9 11.8 16.6 16.6 17.2 15.3 19.1 11.6 15.4 15.4 15.8 14.6 18.1 11.2  
19.7 19.7 19.7 19.4 20.7 14.9 19.0 19.0 19.0 19.0 20.1 15.0 18.1 18.1 18.1 18.1 19.3 15.0 17.1 17.1 17.1 17.1 18.2 14.7  
20.5 20.5 20.5 20.5 20.9 17.9 20.0 20.0 20.0 20.0 20.4 18.2 19.3 19.3 19.3 19.3 19.5 18.3 18.4 18.4 18.4 18.4 18.6 18.2  
3060  
3400  
3740  
27  
30  
33  
4080  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
Table PD-1a — Gross Cooling Capacities (MBH) _ TSC060AD _ (IP)  
Ambient Temperature (F)  
Enter.  
Dry  
Bulb  
Temp  
(F)  
75  
80  
85  
90  
75  
80  
85  
90  
75  
80  
85  
90  
75  
85  
95  
105  
115  
67  
Entering Wet Bulb Temperature (F)  
67 73 61 67  
CFM  
Airflow  
61  
67  
73  
61  
73  
61  
73  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
56.1 47.1 64.4 37.0 68.8 25.1 51.6 44.7 60.6 36.7 66.9 23.9 47.0 42.4 55.6 34.5 64.0 22.6 42.4 40.1 50.2 30.3 60.0 20.8  
57.3 56.5 64.6 45.8 69.3 34.2 53.3 53.3 60.7 43.9 67.3 32.9 49.5 49.5 55.7 41.6 64.2 31.4 45.7 45.7 50.4 39.2 60.1 29.6  
61.3 61.3 64.9 54.5 69.7 42.0 57.7 57.7 61.0 52.9 67.6 41.4 53.9 53.9 56.3 50.7 64.4 40.3 50.0 50.0 51.2 48.3 60.2 38.4  
65.0 65.0 65.8 63.3 70.4 49.7 62.1 62.1 62.4 62.2 68.0 49.7 58.5 58.5 58.5 58.5 64.6 48.8 54.4 54.4 54.4 54.4 60.3 47.2  
57.5 49.8 65.4 38.5 69.3 25.5 53.0 47.5 61.8 38.7 67.5 24.4 48.3 45.1 56.9 36.6 64.7 23.0 43.7 42.8 51.3 34.2 60.9 21.4  
59.3 59.3 65.6 47.9 69.8 35.4 55.7 55.7 62.0 46.4 68.0 34.2 51.6 51.6 57.1 44.1 65.0 32.7 47.7 47.7 51.5 41.6 61.0 30.9  
63.6 63.6 66.0 57.3 70.5 43.1 60.3 60.3 62.5 56.2 68.3 43.0 56.4 56.4 58.0 54.1 65.2 42.1 52.2 52.2 52.8 51.7 61.2 40.6  
66.9 66.9 67.2 66.5 71.1 51.4 64.4 64.4 64.4 64.4 68.9 51.8 61.0 61.0 61.0 61.0 65.6 51.3 57.1 57.1 57.1 57.1 61.5 50.1  
58.8 52.5 66.1 39.8 69.6 25.9 54.3 50.2 62.8 38.1 67.9 24.9 49.4 47.8 58.0 38.6 65.3 23.4 44.8 44.8 52.2 36.2 61.6 21.7  
61.5 61.5 66.4 49.8 70.3 36.8 57.8 57.8 63.0 48.6 68.3 35.0 53.6 53.6 58.2 46.5 65.6 33.9 49.4 49.4 52.6 44.0 61.8 32.2  
65.4 65.4 67.0 59.8 71.0 44.6 62.4 62.4 63.7 59.2 69.0 44.3 58.7 58.7 59.4 57.4 66.0 43.8 54.3 54.3 54.3 54.3 62.0 42.5  
68.4 68.4 68.4 68.4 71.7 52.8 66.1 66.1 66.1 66.1 69.6 53.6 63.1 63.1 63.0 63.0 66.4 53.6 59.3 59.3 59.3 59.3 62.4 52.7  
60.0 55.1 66.6 40.8 70.0 26.4 55.5 52.8 63.6 39.6 68.3 25.3 50.6 50.4 59.0 37.4 65.7 24.0 46.2 46.2 53.1 38.2 62.2 22.1  
63.2 63.2 67.1 51.4 70.7 37.7 59.6 59.6 63.8 50.7 68.8 35.8 55.4 55.4 59.2 48.8 66.2 35.0 51.1 51.1 53.5 46.3 62.4 33.4  
66.7 66.7 67.8 62.0 71.5 45.3 64.1 64.1 64.8 61.9 69.5 45.5 60.5 60.5 60.8 60.6 66.6 45.2 56.3 56.3 56.2 56.2 62.7 44.3  
69.5 69.5 69.5 69.5 72.1 54.1 67.4 67.4 67.4 67.4 70.2 55.3 64.6 64.6 64.5 64.5 67.1 55.7 61.1 61.1 61.0 61.0 63.2 55.1  
1800  
2000  
2200  
80  
85  
90  
2400  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
RT-PRC016-EN  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-2 — Gross Cooling Capacities (kW) -TSC072AD - (SI)  
Ambient Temperature (C)  
Enter.  
Dry  
Bulb  
Temp  
(C)  
24  
27  
30  
33  
24  
27  
30  
33  
24  
27  
30  
33  
24  
30  
35  
19  
40  
45  
19  
Entering Wet Bulb Temperature (C)  
m3/h  
Airflow  
16  
19  
22  
16  
22  
16  
19  
22  
16  
22  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
20.9 17.5 23.3 14.6 24.6 10.3 19.7 16.8 22.4 13.6 24.0 9.9 18.4 16.1 21.2 12.9 23.2 9.4 17.1 15.4 19.7 12.9 22.0 9.0  
21.6 21.2 23.4 17.4 24.8 13.5 20.4 20.4 22.5 17.0 24.1 13.3 19.4 19.4 21.2 16.4 23.3 12.8 18.2 18.2 19.8 15.7 22.1 12.3  
22.9 22.9 23.6 20.6 25.0 16.5 22.1 22.1 22.7 20.4 24.3 16.3 21.0 21.0 21.5 19.9 23.5 16.1 19.9 19.9 20.2 19.2 22.2 15.6  
24.0 24.0 24.1 23.8 25.2 19.4 23.4 23.4 23.3 23.3 24.5 19.3 22.5 22.5 22.4 22.4 23.6 19.3 21.4 21.4 21.4 21.4 22.3 18.8  
21.5 18.5 23.6 15.2 24.8 10.6 20.3 17.9 22.8 14.2 24.2 10.1 19.0 17.2 21.6 13.6 23.4 9.8 17.6 16.4 20.1 12.9 22.3 9.3  
22.3 22.3 23.8 18.1 25.1 14.5 21.3 21.3 22.9 17.9 24.3 13.6 20.2 20.2 21.6 17.3 23.6 13.4 19.0 19.0 20.2 16.6 22.4 12.8  
23.6 23.6 24.0 21.6 25.3 17.6 22.9 22.9 23.2 21.5 24.6 16.8 21.8 21.8 22.0 21.1 23.7 16.7 20.7 20.7 20.8 20.5 22.5 16.3  
24.6 24.6 24.6 24.6 25.5 20.0 23.9 23.9 23.9 23.9 24.8 20.1 23.1 23.1 23.1 23.1 23.9 20.1 22.1 22.1 22.1 22.1 22.7 19.8  
22.0 19.5 23.9 15.8 25.0 10.7 20.8 18.9 23.1 14.7 24.4 10.4 19.5 18.2 21.9 14.2 23.5 10.1 18.1 17.4 20.5 13.5 22.5 9.6  
22.9 22.9 24.0 18.7 25.3 13.9 22.1 22.1 23.2 18.6 24.5 13.9 20.9 20.9 22.0 18.2 23.7 13.6 19.7 19.7 20.6 17.6 22.6 13.3  
24.1 24.1 24.3 22.4 25.5 17.4 23.4 23.4 23.5 22.4 24.8 17.3 22.5 22.5 22.5 22.2 23.9 17.2 21.3 21.3 21.3 21.3 22.8 17.0  
25.0 25.0 25.0 25.0 25.7 20.7 24.4 24.4 24.4 24.4 25.1 20.8 23.7 23.7 23.7 23.7 24.2 20.8 22.6 22.6 22.6 22.6 23.1 20.7  
22.4 20.3 24.1 16.3 25.2 10.9 21.2 19.8 23.2 15.1 24.5 10.7 19.9 19.1 22.2 14.7 23.6 10.3 18.5 18.4 20.8 14.0 22.7 9.9  
23.4 23.4 24.3 19.3 25.5 14.5 22.6 22.6 23.4 19.2 24.7 14.7 21.5 21.5 22.3 19.0 23.8 14.0 20.3 20.3 20.9 18.4 22.8 13.7  
24.5 24.5 24.6 23.2 25.6 17.8 23.8 23.8 23.9 23.2 25.0 17.8 23.0 23.0 23.0 23.0 24.1 17.7 21.8 21.8 21.8 21.8 23.0 17.7  
25.4 25.4 25.4 25.4 25.9 21.2 24.8 24.8 24.8 24.8 25.3 21.4 24.1 24.1 24.1 24.1 24.4 21.4 23.1 23.1 23.1 23.1 23.4 21.6  
3670  
4080  
4490  
27  
30  
33  
4900  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
Table PD-2a — Gross Cooling Capacities (MBH) -TSC072AD - (IP)  
Ambient Temperature (F)  
Enter.  
Dry  
Bulb  
Temp  
(F)  
75  
80  
85  
90  
75  
80  
85  
90  
75  
80  
85  
90  
75  
85  
95  
105  
115  
67  
Entering Wet Bulb Temperature (F)  
67 73 61 67  
CFM  
Airflow  
61  
67  
73  
61  
73  
61  
73  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
72.2 59.1 80.6 47.1 85.1 31.0 67.5 56.5 77.7 44.1 82.7 29.6 62.6 53.9 73.0 41.8 79.9 28.0 57.4 51.2 67.5 39.2 75.5 26.0  
73.8 70.7 81.0 56.1 85.8 42.2 69.4 68.2 77.9 55.0 83.4 40.7 65.0 65.0 73.1 52.6 80.4 39.0 60.6 60.6 67.6 50.0 75.8 36.8  
77.7 77.7 81.4 66.3 86.3 51.7 74.3 74.3 78.2 65.6 83.8 50.1 70.3 70.3 73.6 63.5 80.7 49.2 66.0 66.0 68.3 61.0 76.1 47.4  
81.3 81.3 82.4 76.3 87.1 59.8 78.8 78.8 79.4 76.0 84.6 59.4 75.1 75.1 75.3 74.6 81.3 59.0 70.8 70.8 70.7 70.7 76.6 57.4  
74.2 62.5 81.6 49.2 85.7 31.5 69.3 59.9 78.7 46.0 83.4 30.1 64.4 57.3 74.2 43.7 80.2 28.5 59.1 54.6 68.9 41.1 76.3 26.6  
76.1 75.0 82.1 58.2 86.5 43.7 72.1 72.1 79.0 57.4 84.2 42.1 67.9 67.9 74.4 55.4 80.9 40.4 63.3 63.3 69.0 53.0 76.8 38.4  
80.0 80.0 82.6 69.1 86.8 52.8 77.1 77.1 79.5 68.7 84.7 51.6 73.1 73.1 75.3 67.3 81.4 50.7 68.7 68.7 70.1 65.0 77.2 49.4  
83.3 83.3 83.8 79.7 87.1 61.5 80.7 80.7 80.9 79.4 85.5 61.5 77.5 77.5 77.5 77.5 82.1 61.1 73.3 73.3 73.3 73.3 77.8 60.2  
75.8 65.6 82.3 50.7 86.2 32.0 71.0 63.2 79.4 49.8 84.0 30.7 66.0 60.6 75.4 45.6 80.7 29.0 60.6 57.8 70.0 42.9 77.0 27.2  
78.1 78.1 82.9 60.1 87.2 44.1 74.6 74.6 79.8 59.4 84.7 44.3 70.3 70.3 75.6 58.1 81.2 41.3 65.7 65.7 70.1 55.7 77.6 39.8  
81.7 81.7 83.6 71.6 88.2 54.0 79.1 79.1 80.5 71.3 85.4 53.6 75.4 75.4 76.6 70.7 82.0 52.1 70.9 70.9 71.6 68.7 78.1 51.3  
84.8 84.8 85.0 82.5 89.1 62.3 82.3 82.3 82.3 82.3 86.1 61.2 79.4 79.4 79.4 79.4 82.8 63.0 75.2 75.2 75.2 75.2 78.7 62.8  
77.0 68.3 82.9 52.2 86.6 32.5 72.5 66.4 80.0 51.4 84.5 31.2 67.5 63.7 76.2 47.1 81.2 29.5 62.1 61.0 70.8 44.7 77.6 27.8  
79.6 79.6 83.7 61.8 87.6 44.7 76.6 76.6 80.6 61.3 85.4 44.0 72.4 72.4 76.5 60.5 81.8 42.1 67.7 67.7 71.1 58.2 78.1 40.9  
83.0 83.0 84.4 73.9 88.7 54.9 80.4 80.4 81.5 73.9 86.2 54.1 77.1 77.1 77.8 73.8 82.7 53.5 72.7 72.7 72.9 71.9 78.8 53.0  
85.9 85.9 86.0 85.0 89.6 65.2 83.6 83.6 83.6 83.6 87.0 63.2 81.0 81.0 81.0 81.0 83.5 65.0 76.8 76.8 76.8 76.8 79.5 65.3  
2160  
2400  
2640  
80  
85  
90  
2880  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
RT-PRC016-EN  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-3 — Gross Cooling Capacities (kW) -TSC090AD - (SI)  
Ambient Temperature (C)  
Enter.  
Dry  
Bulb  
Temp  
(C)  
24  
27  
30  
33  
24  
27  
30  
33  
24  
27  
30  
33  
24  
30  
35  
40  
45  
19  
Entering Wet Bulb Temperature (C)  
19 22 16 19  
m3/h  
Airflow  
16  
19  
22  
16  
22  
16  
22  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
24.5 21.6 26.9 17.1 28.1 12.0 22.7 20.6 25.8 16.3 27.7 11.5 20.8 19.6 24.1 15.4 26.8 11.0 19.0 18.7 22.0 14.8 25.6 10.3  
25.4 25.4 27.1 21.1 28.5 15.9 24.1 24.1 25.9 20.8 27.8 15.9 22.5 22.5 24.3 20.0 27.0 15.5 20.9 20.9 22.2 19.0 25.7 14.8  
27.0 27.0 27.4 25.3 28.7 19.5 26.0 26.0 26.4 25.3 28.1 19.7 24.8 24.8 25.0 24.8 27.1 19.6 23.2 23.2 23.1 23.1 25.8 19.2  
28.1 28.1 28.1 28.1 29.0 23.3 27.5 27.5 27.5 27.5 28.4 23.6 26.5 26.5 26.5 26.5 27.4 23.9 25.3 25.3 25.3 25.3 26.1 23.6  
25.1 23.0 27.2 18.1 28.4 12.4 23.4 22.1 26.2 17.1 27.8 11.9 21.4 21.1 24.6 16.8 27.1 11.3 19.7 19.7 22.5 15.3 25.9 10.7  
26.3 26.3 27.4 22.0 28.6 16.3 25.1 25.1 26.4 22.0 28.0 16.2 23.6 23.6 24.9 21.4 27.2 16.0 21.9 21.9 22.8 20.4 26.0 15.6  
27.6 27.6 27.8 26.4 29.0 20.2 26.8 26.8 27.0 26.8 28.3 20.4 25.7 25.7 25.7 25.7 27.4 20.6 24.3 24.3 24.3 24.3 26.2 20.4  
28.6 28.6 28.6 28.6 29.3 24.1 28.1 28.1 28.1 28.1 28.7 24.6 27.3 27.3 27.3 27.3 27.8 25.0 26.2 26.2 26.2 26.2 26.6 25.1  
25.6 24.2 27.4 18.4 28.4 12.5 24.0 23.5 26.5 18.3 28.0 12.2 22.0 22.0 25.1 17.1 27.3 11.7 20.4 20.4 22.9 16.2 26.2 11.1  
26.9 26.9 27.7 22.8 28.8 16.5 25.9 25.9 26.8 23.0 28.3 16.7 24.5 24.5 25.4 22.7 27.4 16.5 22.8 22.8 23.5 21.8 26.3 16.3  
28.0 28.0 28.1 27.3 29.1 20.6 27.4 27.4 27.4 27.4 28.7 21.2 26.5 26.5 26.4 26.4 27.7 21.4 25.2 25.2 25.2 25.2 26.5 21.4  
28.9 28.9 28.9 28.9 29.5 24.7 28.5 28.5 28.5 28.5 29.1 25.6 27.8 27.8 27.8 27.8 28.1 26.0 26.8 26.8 26.8 26.8 27.0 26.3  
26.1 25.4 27.6 18.5 28.5 12.7 24.5 24.5 26.7 19.1 28.1 12.5 22.8 22.8 25.4 18.0 27.4 12.0 21.1 21.1 23.4 17.0 26.3 11.4  
27.3 27.3 27.9 23.4 28.9 16.8 26.5 26.5 27.1 23.9 28.5 17.1 25.3 25.3 25.8 23.8 27.7 17.0 23.6 23.6 24.1 23.1 26.5 16.9  
28.3 28.3 28.4 28.1 29.2 21.0 27.8 27.8 27.8 27.8 28.8 21.8 27.0 27.0 27.0 27.0 27.9 22.1 25.8 25.8 25.8 25.8 26.8 22.3  
29.1 29.1 29.1 29.1 29.6 25.2 28.8 28.8 28.8 28.8 29.3 26.4 28.2 28.2 28.2 28.2 28.4 26.9 27.3 27.3 27.3 27.3 27.4 27.4  
4590  
5100  
5610  
27  
30  
33  
6120  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
Table PD-3a — Gross Cooling Capacities (MBH) -TSC090AD - (IP)  
Ambient Temperature (F)  
Enter.  
Dry  
Bulb  
Temp  
(F)  
75  
80  
85  
90  
75  
80  
85  
90  
75  
80  
85  
90  
75  
85  
95  
105  
115  
67  
Entering Wet Bulb Temperature (F)  
67 73 61 67  
CFM  
Airflow  
61  
67  
73  
61  
73  
61  
73  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
84.4 72.7 92.7 55.2 96.6 35.6 77.7 69.1 89.4 52.6 95.2 34.0 70.4 65.4 83.4 50.6 92.5 32.0 63.7 61.9 75.3 46.9 88.2 29.8  
86.5 86.5 93.3 67.5 97.8 48.9 81.2 81.2 89.6 66.8 96.2 48.4 75.1 75.1 83.8 64.0 93.1 46.6 69.4 69.4 75.8 60.3 88.5 44.1  
91.5 91.5 94.2 80.6 98.9 59.9 87.7 87.7 90.6 80.8 97.2 60.5 82.5 82.5 85.1 78.8 93.5 59.5 76.4 76.4 77.7 75.2 88.8 58.1  
95.1 95.1 95.7 93.2 100.0 71.0 92.6 92.6 92.5 92.5 97.5 71.8 88.7 88.7 88.7 88.7 94.3 72.6 83.7 83.7 83.6 83.6 89.5 71.8  
86.5 77.3 93.5 56.9 97.1 36.1 80.0 73.9 90.6 56.4 95.8 34.6 72.6 70.1 85.2 52.3 93.2 32.7 65.6 65.6 76.9 49.9 89.1 30.5  
89.4 89.4 94.3 70.0 98.3 52.8 84.9 84.9 91.0 70.2 96.9 49.4 78.8 78.8 85.6 68.2 93.9 48.9 72.7 72.7 77.8 64.5 89.6 46.3  
93.6 93.6 95.4 83.8 99.4 61.1 90.6 90.6 92.2 85.2 98.0 62.3 86.1 86.1 87.3 84.2 94.5 61.9 80.1 80.1 80.1 80.1 90.0 61.2  
96.8 96.8 97.0 96.7 100.5 72.8 94.8 94.8 94.8 94.8 99.0 75.4 91.5 91.5 91.4 91.4 95.4 75.8 87.0 87.0 87.0 87.0 90.9 75.9  
88.1 81.3 94.3 59.1 97.5 36.7 82.1 78.5 91.4 58.6 96.2 35.2 74.1 74.1 86.4 54.8 93.7 33.4 68.1 68.1 78.5 51.2 89.8 31.2  
91.4 91.4 95.1 72.1 98.7 50.2 87.6 87.6 92.1 73.3 97.4 50.3 82.2 82.2 87.1 72.0 94.5 49.7 75.6 75.6 79.7 68.7 90.4 48.3  
95.1 95.1 96.2 86.6 99.8 62.1 92.7 92.7 93.6 89.0 98.5 63.8 88.8 88.8 89.2 89.1 95.2 64.0 83.5 83.5 83.5 83.5 90.9 63.9  
97.9 97.9 97.9 97.9 101.0 74.3 96.4 96.4 96.3 96.3 99.7 77.5 93.5 93.5 93.5 93.5 96.3 78.6 89.4 89.4 89.4 89.4 92.1 79.5  
89.5 85.0 95.1 60.6 97.8 37.2 84.0 83.1 92.2 60.7 96.6 35.7 76.7 76.7 87.5 57.3 94.1 34.0 70.4 70.4 80.0 53.8 90.4 31.9  
92.9 92.9 95.6 74.0 99.0 50.8 89.7 89.7 93.0 76.0 97.8 51.0 84.8 84.8 88.3 75.6 95.2 50.9 78.1 78.1 81.6 72.8 90.9 49.5  
96.2 96.2 96.9 88.9 100.2 63.1 94.2 94.2 94.7 92.3 99.0 65.1 90.7 90.7 90.7 90.7 95.8 65.8 86.0 86.0 86.0 86.0 91.7 66.3  
98.7 98.7 98.7 98.7 101.3 75.7 97.5 97.5 97.5 97.5 100.1 79.4 94.9 94.9 94.9 94.9 97.0 81.1 91.2 91.2 91.2 91.2 93.0 82.7  
2700  
3000  
3300  
80  
85  
90  
3600  
NOTES:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
RT-PRC016-EN  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-4 — Gross Cooling Capacities (kW) - TSC102AD - (SI)  
Ambient Temperature (C)  
Enter.  
Dry  
Bulb  
Temp  
(C)  
24  
27  
30  
33  
24  
27  
30  
33  
24  
27  
30  
33  
24  
30  
35  
40  
45  
19  
Entering Wet Bulb Temperature (C)  
19 22 16 19  
m3/h  
Airflow  
16  
19  
22  
16  
22  
16  
22  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
28.0 24.3 31.5 19.5 33.4 14.1 26.0 23.3 30.0 18.7 32.5 13.5 23.9 22.2 27.8 17.7 31.3 12.9 21.6 21.6 25.4 17.3 29.7 12.2  
29.0 28.4 31.6 24.3 33.6 18.7 27.4 27.1 30.1 23.6 32.7 18.5 25.6 25.6 28.0 22.7 31.4 17.8 23.9 23.9 25.6 21.6 29.8 17.1  
31.0 31.0 31.9 29.0 33.9 23.0 29.7 29.7 30.5 28.6 32.9 22.8 28.1 28.1 28.1 28.1 31.5 22.5 26.3 26.3 26.5 25.7 29.9 22.0  
32.6 32.6 32.7 32.1 34.1 27.3 31.6 31.6 31.6 31.4 33.2 27.3 30.4 30.4 30.3 30.3 31.8 27.2 28.9 28.9 28.8 28.8 30.2 26.8  
28.8 25.8 31.9 20.4 33.6 14.4 26.8 24.8 30.5 19.6 32.8 13.9 24.2 24.2 28.5 18.7 31.6 13.4 22.5 22.5 26.0 17.6 30.1 12.6  
30.1 29.8 32.1 25.4 34.0 19.2 28.6 28.6 30.7 25.0 32.9 19.1 26.8 26.8 28.8 24.2 31.7 18.6 25.0 25.0 26.3 23.1 30.2 17.9  
32.0 32.0 32.5 30.5 34.2 23.7 30.9 30.9 30.9 30.9 33.2 23.7 29.4 29.4 29.4 29.4 31.9 23.6 27.6 27.6 27.7 27.2 30.3 23.2  
33.4 33.4 33.4 33.2 34.5 28.1 32.6 32.6 32.5 32.5 33.6 28.5 31.4 31.4 31.4 31.4 32.3 28.5 30.0 30.0 30.0 30.0 30.8 28.3  
29.5 27.3 32.2 21.1 33.8 14.7 27.6 26.3 31.0 20.5 33.0 14.4 25.1 25.1 29.1 19.6 31.8 13.8 23.5 22.9 26.5 18.5 30.4 12.9  
31.0 31.0 32.5 26.5 34.2 19.7 29.7 29.7 31.2 26.3 33.3 19.5 27.9 27.9 29.4 25.6 32.0 19.2 26.0 26.0 27.0 24.5 30.5 18.7  
32.7 32.7 33.0 31.7 34.6 24.5 31.7 31.7 31.7 31.7 33.6 24.6 30.4 30.4 30.5 29.9 32.3 24.5 28.8 28.8 28.8 28.6 30.7 24.3  
34.0 34.0 34.0 34.0 34.8 28.9 33.2 33.2 33.2 33.2 33.9 29.5 32.1 32.1 32.1 32.1 32.7 29.7 30.9 30.9 30.9 30.9 31.3 29.7  
30.1 28.7 32.5 21.7 33.9 15.1 27.9 27.9 31.3 21.4 33.1 14.7 26.0 26.0 29.3 20.4 32.2 14.2 24.2 23.9 27.0 19.4 30.6 13.3  
31.7 31.7 32.8 27.4 34.4 20.0 30.5 30.5 31.6 27.4 33.4 20.0 28.8 28.8 29.8 26.9 32.3 19.7 26.9 26.9 27.6 25.9 30.7 19.4  
33.2 33.2 33.2 33.2 34.8 25.0 32.3 32.3 32.4 31.7 33.7 25.2 31.2 31.2 31.2 30.9 32.6 25.4 29.7 29.7 29.7 29.7 31.0 25.3  
34.4 34.4 34.4 34.4 35.2 30.0 33.7 33.7 33.7 33.7 34.2 30.4 32.9 32.9 32.9 32.9 33.1 30.8 31.5 31.5 31.5 31.5 31.4 31.4  
5200  
5780  
6360  
27  
30  
33  
6940  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
Table PD-4a — Gross Cooling Capacities (MBH) - TSC102AD - (IP)  
Ambient Temperature (F)  
Enter.  
Dry  
Bulb  
Temp  
(F)  
75  
80  
85  
90  
75  
80  
85  
90  
75  
80  
85  
90  
75  
85  
95  
105  
115  
67  
Entering Wet Bulb Temperature (F)  
67 73 61 67  
CFM  
Airflow  
61  
67  
73  
61  
73  
61  
73  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
96.7 81.9 109.1 63.4 115.0 42.2 89.1 78.1 104.0 60.7 112.1 40.4 81.2 74.1 96.3 59.2 107.9 38.3 73.7 70.3 87.0 55.2 102.4 35.8  
98.2 98.2 109.4 78.3 116.1 58.1 92.7 90.8 104.2 76.3 113.0 56.2 85.7 85.2 96.6 72.9 108.5 53.9 79.3 79.3 87.4 68.8 102.7 51.3  
105.0 105.0 110.2 93.1 117.3 70.8 100.0 100.0 105.0 91.8 113.6 70.4 93.6 93.6 98.0 88.8 108.9 68.7 86.8 86.8 89.2 84.7 103.1 66.7  
110.4 110.4 111.6 107.4 118.0 84.0 106.5 106.5 106.4 106.4 114.4 83.5 101.4 101.4 101.7 99.6 109.6 83.1 94.8 94.8 94.9 94.6 103.5 81.6  
99.3 87.0 110.2 65.9 115.6 42.9 91.8 83.2 105.8 63.7 112.9 41.1 83.6 79.1 98.7 60.6 108.8 39.0 75.2 75.2 89.0 58.6 103.4 36.5  
102.5 100.4 110.9 81.6 116.9 59.2 96.7 95.9 106.0 80.4 113.8 58.8 89.7 89.7 99.0 77.4 109.6 56.1 82.9 82.9 89.7 73.3 103.9 53.5  
108.4 108.4 111.9 97.4 118.2 72.7 104.1 104.1 107.2 97.0 114.6 72.7 98.2 98.2 100.8 94.9 110.1 71.5 91.0 91.0 91.0 91.0 104.2 70.0  
113.2 113.2 113.1 113.1 119.5 86.5 109.7 109.7 109.9 107.6 115.6 86.6 105.1 105.1 105.1 104.4 111.0 86.9 99.4 99.4 99.2 99.2 105.1 86.0  
101.6 91.8 111.3 67.8 116.2 43.6 94.3 88.2 107.1 66.5 113.5 41.8 84.7 84.7 100.4 63.0 109.5 39.6 78.4 76.4 90.9 59.0 104.2 37.1  
105.4 104.4 112.1 84.5 117.6 60.0 100.3 100.3 107.4 84.0 114.7 59.4 93.4 93.4 100.9 81.6 110.0 57.9 86.1 86.1 91.7 77.7 104.8 55.6  
111.0 111.0 113.3 101.2 118.9 74.2 107.0 107.0 108.9 101.7 116.0 74.8 101.8 101.8 101.8 101.8 111.2 73.8 94.9 94.9 94.9 94.9 105.3 72.9  
115.2 115.2 115.2 115.2 120.3 88.6 112.1 112.1 112.1 111.1 116.5 89.3 107.8 107.8 107.7 107.7 112.1 90.2 102.6 102.6 102.6 102.6 106.4 90.0  
103.5 96.3 112.1 69.5 116.6 43.8 94.9 94.9 107.9 68.7 114.0 42.5 87.5 87.5 101.8 65.6 110.0 40.3 80.7 79.5 92.4 61.7 104.8 37.8  
107.9 107.9 113.0 87.1 118.1 60.8 103.1 103.1 108.6 87.3 115.3 60.3 96.8 96.8 102.5 85.6 110.7 59.5 89.1 89.1 93.7 82.0 105.4 57.5  
112.9 112.9 114.4 104.5 119.5 75.5 109.3 109.3 110.4 105.7 116.7 76.5 104.5 104.5 104.5 104.5 111.9 76.7 98.2 98.2 98.6 96.7 106.2 75.5  
116.7 116.7 116.7 116.7 120.9 90.6 113.9 113.9 113.8 113.8 117.9 92.9 109.9 109.9 109.8 109.8 113.0 93.2 104.9 104.9 104.9 104.9 107.5 93.5  
3060  
3400  
3740  
80  
85  
90  
4080  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
RT-PRC016-EN  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-5 — Gross Cooling Capacities (kW) -TSC120AD - (SI)  
Ambient Temperature (C)  
Enter.  
Dry  
Bulb  
Temp  
(C)  
24  
27  
30  
33  
24  
27  
30  
33  
24  
27  
30  
33  
24  
30  
35  
40  
45  
19  
Entering Wet Bulb Temperature (C)  
19 22 16 19  
m3/h  
Airflow  
16  
19  
22  
16  
22  
16  
22  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
31.9 28.6 35.3 22.8 37.2 15.9 29.6 27.4 33.6 21.7 36.5 15.4 27.1 26.2 31.0 20.5 35.2 14.8 24.6 24.6 28.4 19.9 33.2 14.0  
33.4 33.4 35.5 28.2 37.7 21.4 31.6 31.6 33.9 27.8 36.7 21.4 29.5 29.5 31.3 26.6 35.3 20.7 27.5 27.5 28.9 25.5 33.3 19.9  
35.5 35.5 36.0 33.8 38.1 26.5 34.2 34.2 34.5 33.8 37.0 26.7 32.3 32.3 32.2 32.2 35.5 26.6 30.4 30.4 30.4 30.4 33.4 25.9  
37.1 37.1 37.1 37.1 38.5 31.6 36.2 36.2 36.2 36.2 37.3 31.9 34.8 34.8 34.8 34.8 35.9 32.3 33.2 33.2 33.2 33.2 34.0 31.8  
32.7 30.4 35.7 23.8 37.5 16.3 30.5 29.3 34.2 22.8 36.8 15.9 27.8 27.8 31.9 21.8 35.5 15.3 25.7 25.7 29.0 21.2 33.7 14.5  
34.5 34.5 36.0 29.5 38.0 21.9 32.9 32.9 34.5 29.4 37.0 22.0 30.9 30.9 32.3 28.5 35.7 21.7 28.7 28.7 29.7 27.4 33.8 21.0  
36.3 36.3 36.6 35.4 38.4 27.4 35.3 35.3 35.3 35.3 37.3 27.6 33.7 33.7 33.7 33.7 35.9 27.8 31.8 31.8 31.7 31.7 34.0 27.5  
37.9 37.9 37.8 37.8 38.9 32.8 37.0 37.0 37.0 37.0 37.8 33.3 35.9 35.9 35.9 35.9 36.5 33.9 34.4 34.4 34.4 34.4 34.7 33.8  
33.5 32.2 36.0 24.7 37.8 16.9 31.1 31.1 34.7 23.9 37.0 16.3 28.9 28.9 32.4 22.9 35.8 15.7 26.6 26.6 29.6 22.5 34.1 14.9  
35.3 35.3 36.4 30.6 38.2 22.4 34.0 34.0 35.0 30.8 37.4 22.7 32.0 32.0 33.0 30.2 36.0 22.5 29.9 29.9 30.5 29.1 34.2 22.0  
37.0 37.0 37.0 37.0 38.7 28.1 36.1 36.1 36.1 36.1 37.9 28.9 34.7 34.7 34.7 34.7 36.4 29.1 32.9 32.9 32.9 32.9 34.5 29.0  
38.4 38.4 38.3 38.3 39.2 33.7 37.7 37.7 37.7 37.7 38.4 34.9 36.7 36.7 36.7 36.7 37.0 35.4 35.3 35.3 35.3 35.3 35.3 35.3  
33.9 33.9 36.3 24.9 37.9 17.3 32.0 32.0 35.0 25.6 37.5 16.1 29.8 29.8 32.8 23.9 36.1 16.2 27.5 27.5 29.8 23.6 34.4 15.3  
35.9 35.9 36.7 31.7 38.5 22.8 34.8 34.8 35.5 32.2 37.7 23.2 32.9 32.9 33.6 31.9 36.3 23.2 30.6 30.6 30.6 30.6 34.5 23.0  
37.5 37.5 37.5 37.5 38.9 28.8 36.7 36.7 36.7 36.7 38.1 29.8 35.5 35.5 35.5 35.5 36.7 30.2 33.7 33.7 33.7 33.7 34.9 30.5  
38.8 38.8 38.7 38.7 39.5 34.6 38.4 38.4 38.2 38.2 38.7 36.1 37.3 37.3 37.3 37.3 37.4 36.7 36.0 36.0 36.0 36.0 36.0 36.0  
6120  
6800  
7480  
27  
30  
33  
8160  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
Table PD-5a — Gross Cooling Capacities (MBH) -TSC120AD - (IP)  
Ambient Temperature (F)  
Enter.  
Dry  
Bulb  
Temp  
(F)  
75  
80  
85  
90  
75  
80  
85  
90  
75  
80  
85  
90  
75  
85  
95  
105  
115  
67  
Entering Wet Bulb Temperature (F)  
67 73 61 67  
CFM  
Airflow  
61  
67  
73  
61  
73  
61  
73  
TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC TGC SHC  
109.9 96.4 122.1 73.8 128.5 47.6 101.2 92.1 116.7 70.3 125.9 45.7 91.8 87.5 107.7 67.7 121.6 43.4 82.1 82.1 97.2 63.2 115.0 40.9  
113.5 113.5 122.6 90.4 129.9 65.7 106.6 106.6 117.1 89.2 127.2 65.0 99.0 99.0 108.4 85.4 122.2 62.4 91.0 91.0 98.2 81.0 115.2 59.7  
120.2 120.2 123.8 108.0 131.3 80.9 115.2 115.2 118.5 107.9 127.8 81.5 108.1 108.1 110.5 104.9 122.6 80.6 100.3 100.3 100.3 100.3 115.4 78.4  
125.4 125.4 125.4 125.4 132.7 96.3 121.8 121.8 121.8 121.8 128.7 97.3 116.4 116.4 116.4 116.4 123.6 98.2 109.2 109.2 109.2 109.2 116.4 97.0  
112.7 102.4 123.1 75.6 129.3 48.4 104.2 98.3 118.5 73.6 126.9 46.6 93.7 93.7 109.9 70.9 122.7 44.3 85.6 85.6 99.3 67.2 116.5 41.9  
117.3 117.3 124.1 94.1 130.8 66.9 111.1 111.1 119.0 94.0 128.2 66.8 103.5 103.5 110.8 90.8 123.5 65.3 95.2 95.2 100.8 86.6 116.8 62.5  
123.2 123.2 125.6 112.8 132.3 82.9 119.0 119.0 120.8 114.1 129.5 84.5 112.5 112.5 112.5 112.5 124.1 84.2 104.9 104.9 104.8 104.8 117.1 83.0  
127.9 127.9 127.9 127.9 133.8 99.2 124.9 124.9 124.9 124.9 130.8 102.4 120.2 120.2 120.2 120.2 125.3 103.1 113.9 113.9 113.8 113.8 118.4 102.9  
115.1 108.2 124.5 77.5 130.0 49.2 107.0 104.4 119.8 77.6 127.6 47.4 97.3 97.3 111.7 73.2 123.6 45.2 88.7 88.7 101.1 71.1 117.6 42.7  
120.1 120.1 125.3 97.3 131.6 67.9 114.9 114.9 120.6 98.4 129.0 68.2 107.3 107.3 112.9 96.1 124.5 68.1 98.9 98.9 103.1 92.0 118.0 65.1  
125.5 125.5 127.0 116.9 133.1 84.7 121.9 121.9 122.8 119.6 130.5 87.0 116.4 116.4 116.3 116.3 125.3 88.0 108.7 108.7 108.7 108.7 118.4 87.0  
130.0 130.0 129.7 129.7 134.7 101.8 127.3 127.3 127.2 127.2 131.9 105.9 123.0 123.0 123.0 123.0 126.7 107.5 117.2 117.2 117.2 117.2 120.2 108.4  
117.1 113.2 125.5 81.7 130.6 50.0 108.8 108.8 120.8 80.6 128.3 48.2 100.5 100.5 113.2 76.3 124.3 46.1 91.6 91.6 102.7 72.1 118.5 43.6  
122.3 122.3 126.5 100.7 132.2 68.9 117.8 117.8 122.0 102.4 129.8 69.5 110.5 110.5 114.9 101.3 125.7 69.3 102.2 102.2 105.2 97.3 119.0 67.7  
127.2 127.2 128.4 121.1 133.8 86.3 124.1 124.1 124.1 124.1 131.2 89.2 119.0 119.0 119.0 119.0 126.5 90.9 112.0 112.0 112.0 112.0 119.7 90.9  
131.3 131.3 131.5 131.5 135.4 104.2 129.3 129.3 129.0 129.0 132.8 108.9 125.2 125.2 125.2 125.2 127.8 111.4 119.8 119.8 119.8 119.8 121.7 113.3  
3600  
4000  
4400  
80  
85  
90  
4800  
Notes:  
1. All capacities shown are gross and have not considered indoor fan heat. To obtain net cooling, subtract indoor fan heat.  
2. TGC = Total Gross Capacity  
3. SHC = Sensible Heat Capacity  
RT-PRC016-EN  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-6 — Belt Drive Evaporator Fan Performance - TSC060AD - Downflow Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
1.12 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
175  
RPM  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
1.12 Nom kW Standard Motor & Drive  
0.49 985 0.54 1023 0.59 1060 0.64  
0.58 1028 0.64 1067 0.70 1104 0.76  
2720  
3060  
3400  
3740  
4080  
-
-
703  
760  
821  
885  
950  
0.27  
0.35  
0.46  
0.60  
0.76  
757  
815  
873  
930  
990  
0.31  
0.40  
0.51  
0.65  
0.80  
806  
861  
918  
977  
0.35  
0.45  
0.57  
0.71  
854  
904  
958  
1016 0.77  
1074 0.93  
0.39  
0.49  
0.62  
899  
947  
998  
1053 0.82  
1110 1.00  
0.43  
0.54  
0.67  
944  
988  
706  
773  
840  
909  
0.32  
0.43  
0.56  
0.71  
1036 0.71 1073 0.76 1111 0.82 1147 0.89  
1089 0.88  
1143 1.06  
1124 0.93  
1177 1.12  
1158 0.98  
1209 1.17  
1191 1.03  
1241 1.23  
1034 0.87  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM  
275  
RPM  
375  
RPM  
CFM  
kW  
RPM  
kW  
kW  
kW  
kW  
1.12 Nom kW Standard Motor & Drive  
2720  
3060  
3400  
3740  
4080  
Notes:  
1093 0.69  
1138 0.82  
1182 0.96  
1226 1.10  
1272 1.29  
1126 0.74  
1171 0.87  
1215 1.02  
1258 1.17  
1160 0.79  
1203 0.93  
1246 1.09  
1290 1.25  
1190 0.84  
1232 0.98  
1276 1.15  
1222 0.90  
1262 1.04  
1306 1.21  
1.12 Nom kW Standard Motor &  
Hi Static Drive  
-
-
-
-
-
-
-
-
-
-
-
-
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132  
Table PD-6a — Belt Drive Evaporator Fan Performance -TSC060AD - Downflow Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP RPM BHP RPM BHP RPM BHP  
1-1/2 HP Standard Motor & Low Static Drive  
1-1/2 HP Standard Motor & Drive  
1600  
1800  
2000  
2200  
2400  
-
-
703  
760  
821  
885  
950  
0.36  
0.47  
0.62  
0.80  
1.02  
757  
815  
873  
930  
990  
0.41  
0.54  
0.69  
0.87  
1.08  
806  
861  
918  
977  
0.47  
0.60  
0.76  
0.95  
854  
904  
958  
1016 1.03  
1074 1.25  
0.52  
0.66  
0.83  
899  
947  
998  
1053 1.10  
1110 1.34  
0.58  
0.72  
0.90  
944  
988  
0.65  
985  
0.73 1023 0.79 1060 0.86  
706  
773  
840  
909  
0.42  
0.57  
0.75  
0.96  
0.78 1028 0.86 1067 0.94 1104 1.02  
1036 0.96 1073 1.02 1111 1.10 1147 1.19  
1089 1.17  
1143 1.419 1177 1.50  
1124 1.24  
1158 1.31  
1209 1.57  
1191 1.39  
1241 1.65  
1034 1.16  
External Static Pressure (Inches of Water)  
1.10  
1.20  
1.30  
1.40  
1.50  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
1-1/2 HP Standard Motor & Drive  
1600  
1800  
2000  
2200  
2400  
Notes:  
1093 0.92  
1138 1.10  
1182 1.28  
1226 1.48  
1272 1.73  
1126 0.99  
1171 1.17  
1215 1.37  
1258 1.57  
1160 1.06  
1203 1.25  
1246 1.46  
1290 1.67  
1190 1.13  
1232 1.32  
1276 1.54  
1222 1.20  
1262 1.39  
1306 1.62  
1-1/2 HP Standard Motor &  
Hi Static Drive  
-
-
-
-
-
-
-
-
-
-
-
-
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451  
RT-PRC016-EN  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-7 - Belt Drive Evaporator Fan Performance- TSC060AD - Horizontal Configuration - (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
125  
RPM  
150  
RPM  
1.12 Nom kW Standard Motor & Drive  
175  
RPM  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
1.12 Nom kW Std Motor & Low Static Drive  
2720  
3060  
3400  
3740  
4080  
707  
778  
850  
923  
997  
0.26  
0.36  
0.48  
0.63  
0.80  
774  
840  
908  
978  
0.31  
0.41  
0.54  
0.69  
837  
897  
961  
1028 0.76  
1096 0.94  
0.37  
0.48  
0.60  
898  
953  
1012 0.67  
1075 0.83  
1140 1.02  
0.43  
0.54  
953  
0.48  
1001 0.54  
1058 0.67  
1111 0.81  
1166 0.99  
1223 1.18  
1045 0.59 1087 0.65 1129 0.71 1168 0.77  
1008 0.60  
1062 0.74  
1120 0.91  
1183 1.10  
1102 0.73  
1157 0.88  
1211 1.06  
1266 1.27  
1143 0.79  
1198 0.95  
1254 1.14  
1181 0.85  
1237 1.02  
1294 1.22  
1219 0.92  
1274 1.09  
1330 1.29  
1049 0.87  
-
-
-
-
-
-
1.12 Nom kW Standard Motor & Hi Static Drive  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM RPM  
275  
RPM  
375  
RPM  
CFM  
kW  
kW  
kW  
kW  
kW  
1.12 Nom kW Standard Motor & Drive  
2720  
3060  
3400  
3740  
4080  
1206 0.83  
1256 0.99  
1309 1.16  
1241 0.89  
1291 1.05  
1343 1.24  
1275 0.96  
1326 1.12  
1376 1.31  
1306 1.02  
1359 1.19  
1338 1.09  
1390 1.26  
1.12 Nom kW Standard Motor &  
Hi Static Drive  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132  
Table PD-7a - Belt Drive Evaporator Fan Performance- TSC060AD - Horizontal Configuration - (IP)  
External Static Pressure (Inches of Water)  
0.10  
0.20  
0.30  
0.40  
0.50  
0.60  
0.70  
0.80  
0.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP RPM BHP RPM BHP RPM BHP  
1-1/2 HP Standard Motor &  
Low Static Drive  
1-1/2 HP Standard Motor & Drive  
1600  
1800  
2000  
2200  
2400  
707  
778  
850  
923  
997  
0.35  
0.48  
0.65  
0.84  
1.07  
774  
840  
908  
978  
0.42  
0.56  
0.73  
0.93  
837  
897  
961  
1028 1.02  
1096 1.27  
0.50  
0.64  
0.81  
898  
953  
1012 0.90  
1075 1.12  
1140 1.37  
0.57  
0.72  
953  
0.65  
1001 0.72  
1058 0.89  
1111 1.09  
1166 1.32  
1223 1.59  
1045 0.80 1087 0.87 1129 0.95 1168 1.03  
1008 0.81  
1062 1.00  
1120 1.22  
1183 1.48  
1102 0.98  
1157 1.19  
1211 1.43  
1266 1.70  
1143 1.06  
1198 1.28  
1254 1.53  
1181 1.15  
1237 1.37  
1294 1.63  
1219 1.23  
1274 1.47  
1330 1.74  
1049 1.17  
-
-
-
-
-
-
1-1/2 HP Standard Motor & Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
CFM  
1/2 HP Standard Motor & Drive  
1-1/2 HP Standard Motor & Hi Static Drive  
1600  
1800  
2000  
2200  
2400  
1206 1.12  
1256 1.32  
1309 1.56  
1241 1.20  
1291 1.41  
1343 1.66  
1275 1.28  
1326 1.50  
1376 1.76  
1306 1.37  
1359 1.60  
1338 1.46  
1390 1.69  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451  
RT-PRC016-EN  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-8 — Belt Drive Evaporator Fan Performance -TSC072AD - Downflow Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
1.12 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
1.12 Nom kW Standard Motor & Drive  
175  
RPM  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
3260  
3670  
4080  
4490  
4890  
-
-
-
-
-
-
-
-
573  
602  
635  
670  
706  
0.25  
0.31  
0.38  
0.47  
0.58  
630  
656  
682  
715  
749  
0.30  
0.37  
0.45  
0.54  
0.64  
680  
706  
732  
758  
789  
0.36  
0.43  
0.51  
0.60  
0.71  
726  
751  
777  
802  
830  
0.41  
0.49  
0.58  
0.68  
0.79  
769  
792  
818  
845  
870  
0.47  
0.55  
0.64  
0.75  
0.87  
811  
832  
856  
883  
909  
0.52  
0.61  
0.71  
0.82  
0.95  
851 0.58  
871 0.67  
893 0.77  
919 0.89  
945 1.02  
889 0.65  
908 0.74  
930 0.84  
953 0.96  
979 1.10  
548  
584  
621  
660  
0.26  
0.33  
0.42  
0.51  
569  
612  
0.35  
0.45  
1.12 Nom kW Standard Motor  
& Hi Static Drive  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM  
275  
RPM  
375  
RPM  
CFM  
kW  
RPM  
kW  
kW  
kW  
kW  
1.12 Nom kW Std Motor  
& Drive  
1.12 Nom kW Standard Motor  
& Hi Static Drive  
3260  
3670  
4080  
4490  
4890  
925  
944  
964  
986  
0.71  
0.81  
0.91  
1.04  
960  
978  
998  
1019 1.11  
1043 1.26  
0.77  
0.87  
0.99  
994  
0.83  
1026 0.89  
1043 1.01  
1063 1.14  
1082 1.27  
1103 1.42  
1057 0.95  
1073 1.08  
1092 1.21  
1112 1.35  
1133 1.51  
1010 0.94  
1030 1.06  
1051 1.19  
1073 1.34  
1011 1.18  
1.50 Nom kW Over-Sized Motor  
& Hi Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
Table PD-8a — Belt Drive Evaporator Fan Performance -TSC072AD - Downflow Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP RPM BHP RPM BHP RPM BHP  
1-1/2 HP Standard Motor  
&
Low Static Drive  
1-1/2 HP Standard Motor  
&
Drive  
0.70  
0.81  
0.95  
1.10  
1.27  
1920  
2160  
2400  
2640  
2880  
-
-
-
-
-
-
573  
602  
635  
670  
706  
0.34  
0.42  
0.52  
0.64  
0.78  
630  
656  
682  
715  
749  
0.41  
0.50  
0.60  
0.72  
0.86  
680  
706  
732  
758  
789  
0.48  
0.58  
0.69  
0.81  
0.96  
726  
751  
777  
802  
830  
0.55  
0.65  
0.77  
0.91  
1.06  
769  
792  
818  
845  
870  
0.62  
0.73  
0.86  
1.01  
1.16  
811  
832  
856  
883  
909  
851 0.78  
871 0.90  
893 1.04  
919 1.20  
945 1.37  
889 0.87  
908 0.99  
930 1.13  
953 1.29  
979 1.48  
548  
584  
621  
660  
0.35  
0.45  
0.56  
0.69  
-
-
569  
612  
0.47  
0.60  
1-1/2 HP Standard Motor  
& Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
CFM  
1-1/2 HP Standard Mtr  
& Drive  
1920  
2160  
2400  
2640  
2880  
925  
944  
964  
986  
0.95  
1.08  
1.22  
1.39  
960  
978  
998  
1019 1.49  
1043 1.69  
1.03  
1.17  
1.32  
994  
1.11  
1026 1.19  
1043 1.36  
1063 1.53  
1082 1.71  
1103 1.90  
1057 1.27  
1073 1.44  
1092 1.63  
1112 1.81  
1133 2.02  
1-1/2 HP Standard Motor  
Hi Static Drive  
&
1010 1.26  
1030 1.42  
1051 1.60  
1073 1.79  
1011 1.58  
2 HP Over-Sized Mtr & Hi Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
RT-PRC016-EN  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-9 — Belt Drive Evaporator Fan Performance -TSC072AD - Horizontal Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
Low Static Drive  
125  
RPM  
150  
RPM  
1.12 Nom kW Standard Motor  
175  
RPM  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
&
kW  
kW  
kW  
kW  
kW  
kW  
1.12 Nom kW Standard Motor  
&
Drive  
3260  
3670  
4080  
4490  
4890  
-
-
565  
609  
660  
710  
762  
0.23  
0.31  
0.40  
0.51  
0.64  
627  
663  
701  
745  
795  
0.29  
0.36  
0.45  
0.56  
0.70  
679  
716  
751  
788  
828  
0.34  
0.42  
0.51  
0.62  
0.76  
726  
762  
798  
833  
869  
0.39  
0.48  
0.59  
0.69  
0.82  
771  
804  
839  
875  
911  
0.45  
0.54  
0.65  
0.77  
0.91  
814  
843  
877  
914  
950  
0.51  
0.60  
0.71  
0.85  
0.99  
857  
883  
914  
949  
986  
0.57  
0.67  
0.78  
0.91  
899 0.63  
922 0.74  
950 0.85  
939 0.70  
960 0.81  
984 0.93  
566  
619  
672  
726  
0.26  
0.35  
0.45  
0.58  
984 0.98 1016 1.06  
1.07 1019 1.14 1051 1.22  
1.12 Nom kW Standard Motor  
& Hi Static Drive  
1.12 Nom kW Standard Motor  
&
Drive  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM RPM  
275  
RPM  
375  
RPM  
CFM  
kW  
kW  
kW  
kW  
kW  
1.12 Nom kW Standard Motor & Hi Static Drive  
3260  
3670  
4080  
4490  
4890  
978  
996  
1020 1.00  
1049 1.14  
1081 1.30  
0.76  
0.87  
1015 0.83  
1034 0.95  
1055 1.08  
1081 1.23  
1112 1.38  
1051 0.90  
1069 1.02  
1089 1.16  
1113 1.31  
1141 1.47  
1086 0.97  
1103 1.09  
1122 1.23  
1144 1.40  
1170 1.57  
1118 1.04  
1136 1.17  
1154 1.31  
1176 1.48  
1199 1.66  
1.50 Nom kW Over-Sized Motor & Hi Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.12 kW - Fan Motor Heat (kW) = 1.144 x Fan kW + 0.132  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
Table PD-9a — Belt Drive Evaporator Fan Performance -TSC072AD - Horizontal Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP RPM BHP RPM BHP RPM BHP  
1-1/2 HP Standard Motor & Low Static Drive  
1-1/2 HP Standard Motor  
&
Drive  
1920  
2160  
2400  
2640  
2880  
-
-
565  
609  
660  
710  
762  
0.31  
0.41  
0.54  
0.68  
0.86  
627  
663  
701  
745  
795  
0.39  
0.48  
0.60  
0.76  
0.94  
679  
716  
751  
788  
828  
0.45  
0.57  
0.69  
0.83  
1.02  
726  
762  
798  
833  
869  
0.52  
0.64  
0.78  
0.93  
1.11  
771  
804  
839  
875  
911  
0.60  
0.72  
0.87  
1.04  
1.21  
814  
843  
877  
914  
950  
0.69  
857  
883  
914  
949  
986  
0.77  
0.90  
1.04  
1.22  
899 0.85  
922 0.99  
950 1.14  
939 0.93  
960 1.08  
984 1.24  
566  
619  
672  
726  
0.35  
0.47  
0.61  
0.77  
0.80  
0.95  
1.13  
1.33  
984 1.31 1016 1.42  
1.44 1019 1.53 1051 1.63  
1-1/2 HP Standard Motor  
&
Drive  
1-1/2 HP Std Motor & Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
CFM  
1-1/2 HP Standard Motor  
&
Hi Static Drive  
1920  
2160  
2400  
2640  
2880  
978  
996  
1020 1.35  
1049 1.53  
1081 1.74  
1.02  
1.17  
1015 1.11  
1034 1.27  
1055 1.45  
1081 1.65  
1112 1.86  
1051 1.20  
1069 1.36  
1089 1.55  
1113 1.76  
1141 1.97  
1086 1.30  
1103 1.46  
1122 1.66  
1144 1.87  
1170 2.10  
1118 1.39  
1136 1.56  
1154 1.76  
1176 1.98  
1199 2.22  
2 HP Over-Sized Motor  
&
High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1 1/2 HP - Fan Motor Heat (MBH) = 2.915 x Fan BHP + 0.451  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
RT-PRC016-EN  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-10 — Belt Drive Evaporator Fan Performance -TSC090AD - Downflow Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
1.50 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
175  
RPM  
1.50 Nom kW Standard Motor  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
&
Drive  
4080  
4590  
5100  
5610  
6120  
-
-
-
-
-
-
-
-
-
-
-
-
701  
743  
789  
836  
885  
0.47  
0.59  
0.74  
0.92  
1.14  
750  
787  
827  
873  
921  
0.54  
0.66  
0.82  
1.00  
1.22  
794  
830  
867  
908  
954  
0.60  
0.74  
0.90  
1.08  
1.30  
834  
871  
906  
944  
986  
0.67  
0.82  
0.98  
1.17  
873  
908  
944  
980  
0.73  
0.89  
1.06  
1.26  
909 0.80  
943 0.96  
980 1.15 1013 1.23  
1016 1.35 1050 1.45  
945 0.87  
977 1.04  
699  
747  
797  
848  
0.53  
0.68  
0.85  
1.06  
703  
755  
809  
0.61  
0.77  
0.96  
713  
771  
0.69  
0.88  
1.39 1019 1.49 1052 1.58 1085 1.69  
1.50 Nom kW Standard Motor  
& Hi Static Drive  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM  
275  
RPM  
375  
RPM  
CFM  
kW  
RPM  
kW  
kW  
kW  
kW  
1.50 Nom kW Std Motor  
& Drive  
1.50 Nom kW Standard Motor  
& Hi Static Drive  
4080  
4590  
5100  
5610  
6120  
980  
0.95  
1013 1.02  
1043 1.19  
1076 1.39  
1111 1.63  
1148 1.89  
1046 1.10  
1074 1.27  
1105 1.47  
1141 1.72  
1177 1.99  
1076 1.17  
1105 1.36  
1134 1.56  
1168 1.80  
1204 2.08  
1106 1.25  
1134 1.44  
1163 1.65  
1197 1.90  
1232 2.18  
1010 1.11  
1045 1.31  
1081 1.54  
1116 1.79  
2.24 Nom kW Over-Sized Motor  
& Hi Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-10a — Belt Drive Evaporator Fan Performance -TSC090AD - Downflow Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
Drive  
.80  
.90  
1.00  
CFM  
RPM BHP  
2 HP Standard Motor  
RPM BHP  
RPM BHP  
Low Static Drive  
RPM BHP  
RPM BHP  
RPM BHP  
2 HP Standard Motor  
&
&
2400  
2700  
3000  
3300  
3600  
-
-
-
-
-
-
-
-
-
-
-
-
701  
743  
789  
836  
885  
0.63  
0.79  
0.99  
1.24  
1.53  
750  
787  
827  
873  
921  
0.72  
0.89  
1.10  
1.34  
1.63  
794  
830  
867  
908  
954  
0.81  
0.99  
1.20  
1.45  
1.74  
834  
871  
906  
944  
986  
0.90  
1.09  
1.31  
1.57  
873  
908  
944  
980  
0.98  
1.19  
1.43  
1.69  
909 1.08  
943 1.29  
980 1.54  
1016 1.82  
945 1.17  
977 1.39  
1013 1.65  
1050 1.94  
699  
747  
797  
848  
0.70  
0.91  
1.15  
1.42  
703  
755  
809  
0.81  
1.03  
1.29  
713  
771  
0.93  
1.19  
1.87 1019 1.99 1052 2.13 1085 2.26  
2 HP Standard Motor  
& Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
CFM  
2 HP Standard Mtr  
& Drive  
2 HP Standard Motor &  
Hi Static Drive  
2400  
2700  
3000  
3300  
3600  
980  
1.27  
1010 1.49  
1045 1.76  
1081 2.06  
1116 2.39  
1013 1.37  
1046 1.47  
1076 1.57  
1105 1.82  
1134 2.09  
1168 2.42  
1204 2.79  
1106 1.68  
1043 1.60  
1076 1.87  
1111 2.18  
1148 2.53  
1074 1.71  
1105 1.98  
1141 2.30  
1177 2.66  
1134 1.93  
1163 2.21  
1197 2.55  
1232 2.93  
3 HP Over-Sized Mtr & Hi Static Drive  
Notes:  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
RT-PRC016-EN  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-11 — Belt Drive Evaporator Fan Performance -TSC090AD - Horizontal Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
125  
RPM  
150  
RPM  
1.50 Nom kW Standard Motor  
175  
RPM  
200  
RPM  
Drive  
225  
RPM kW  
250  
RPM kW  
m3/h  
1.50 Nom kW Std Motor & Low Static Drive  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
&
4080  
4590  
5100  
5610  
6120  
-
-
673  
738  
805  
873  
942  
0.42  
0.56  
0.74  
0.96  
1.22  
718  
773  
837  
903  
970  
0.47  
0.62  
0.81  
1.03  
1.30  
769  
817  
870  
930  
996  
0.54  
0.68  
0.87  
1.10  
1.37  
814  
862  
912  
963  
0.61  
0.76  
0.94  
1.17  
855  
904  
951  
1000 1.25  
1052 1.52  
0.67  
0.85  
1.03  
893  
941  
989  
0.73  
0.92  
929  
975  
0.81  
0.98  
965 0.88  
1009 1.06  
999 0.96  
1041 1.14  
702  
771  
842  
913  
0.51  
0.68  
0.89  
1.14  
1.12 1025 1.21 1056 1.28 1088 1.36  
1037 1.34 1073 1.45 1106 1.55 1136 1.63  
1086 1.61 1121 1.71 1153 1.82 1184 1.93  
1021 1.45  
1.50 Nom kW Standard Motor  
&
Drive  
1.50 Nom kW Standard Motor &  
Hi Static Drive  
2.24 Nom kW OS  
Motor & Hi Static Drive  
External Static Pressure (Pascals)  
300 325 350  
RPM RPM RPM  
1.50 Nom kW Standard Motor & Hi Static Drive  
275  
RPM  
375  
RPM kW  
CFM  
kW  
kW  
kW  
kW  
4080  
4590  
5100  
5610  
6120  
1035 1.04  
1073 1.22  
1117 1.44  
1165 1.72  
1215 2.04  
1070 1.12  
1104 1.31  
1146 1.53  
1194 1.80  
1242 2.13  
1104 1.19  
1136 1.40  
1176 1.62  
1220 1.88  
1269 2.22  
1137 1.27  
1167 1.48  
1205 1.72  
1248 1.98  
1295 2.31  
1168 1.35  
1198 1.57  
1233 1.82  
1275 2.08  
1319 2.40  
2.24 Nom kW Over-Sized Motor & Hi Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-11a — Belt Drive Evaporator Fan Performance -TSC090AD - Horizontal Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
Drive  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
2 HP Std Motor & Low Static Drive  
2 HP Standard Motor  
&
2400  
2700  
3000  
3300  
3600  
-
-
673  
738  
805  
873  
942  
0.56  
0.76  
1.00  
1.29  
1.63  
718  
773  
837  
903  
970  
0.63  
0.83  
1.08  
1.38  
1.74  
769  
817  
870  
930  
996  
0.72  
0.92  
1.17  
1.47  
1.84  
814  
862  
912  
963  
0.82  
1.02  
1.26  
1.57  
855  
904  
951  
1000 1.68  
1052 2.04  
0.90  
1.13  
1.38  
893  
941  
989  
0.98  
1.23  
929  
975  
1.08  
965 1.18  
999 1.29  
702  
771  
842  
913  
0.68  
0.91  
1.19  
1.53  
1.32 1009 1.42 1041 1.52  
1.51 1025 1.62 1056 1.72 1088 1.82  
1037 1.80 1073 1.94 1106 2.08 1136 2.19  
1086 2.16 1121 2.29 1153 2.44 1184 2.59  
1021 1.94  
2 HP Standard Motor  
&
Drive  
2 HP Std Motor & Hi Static Drive  
3 HP Over-Sized Motor  
& Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
1.20  
1.30  
1.40  
1.50  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
2 HP Standard Motor  
&
Hi Static Drive  
2400  
2700  
3000  
3300  
3600  
1035 1.39  
1073 1.64  
1117 1.93  
1165 2.30  
1215 2.73  
1070 1.50  
1104 1.76  
1146 2.05  
1194 2.41  
1242 2.86  
1104 1.60  
1136 1.87  
1176 2.17  
1220 2.52  
1269 2.98  
1137 1.70  
1167 1.99  
1205 2.31  
1248 2.66  
1295 3.10  
1168 1.81  
1198 2.11  
1233 2.44  
1275 2.79  
1319 3.22  
3 HP Over-Sized Motor  
&
High Static Drive  
Notes:  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
Factory Supplied Motors, In Com m ercial Equipm ent, Are  
Definite Purpose Motors, Specifically Designed And  
Tested To Operate Reliably And Continuously At All  
Cataloged Conditions. Using The Full Horsepower Range  
Of Our Fan Motors As Shown In Our Tabular Data Will  
Not Result In Nuisance Tripping Or Prem ature Motor  
Failure. Our Products Warranty Will Not Be Affected.  
RT-PRC016-EN  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-12 — Belt Drive Evaporator Fan Performance -TSC102AD - Downflow Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
1.50 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
175  
RPM  
1.50 Nom kW Standard Motor  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
&
Drive  
4620  
5200  
5780  
6350  
6930  
-
-
-
-
-
-
-
-
-
-
-
-
613  
650  
689  
729  
770  
0.45  
0.55  
0.68  
0.82  
0.98  
655  
688  
724  
764  
804  
0.54  
0.64  
0.76  
0.92  
1.09  
695  
725  
759  
795  
834  
0.62  
0.73  
0.86  
1.01  
1.19  
733  
761  
792  
826  
864  
0.71  
0.83  
0.96  
1.11  
1.30  
769  
796  
825  
857  
892  
0.81  
0.93  
1.07  
1.22  
1.40  
802 0.90  
828 1.03  
856 1.18  
887 1.34  
920 1.52  
833 1.00  
861 1.13  
887 1.28  
916 1.46  
948 1.64  
611  
651  
693  
738  
0.48  
0.59  
0.72  
0.89  
612  
659  
706  
0.51  
0.64  
0.80  
622  
671  
0.56  
0.71  
1.50 Nom kW Standard  
Motor & Hi Static Drive  
External Static Pressure (Pascals)  
375 400  
RPM RPM  
275  
RPM  
300  
RPM  
325  
RPM  
350  
RPM  
425  
RPM  
450  
RPM  
475  
RPM kW  
500  
RPM kW  
m3/h  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
1.50 Nom kW Std Mtr & Drive  
1.50 Nom kW Std Mtr & Hi Static Dr  
4620  
5200  
5780  
6350  
6930  
863  
891  
917  
945  
976  
1.11  
1.24  
1.40  
1.58  
1.78  
892  
919  
946  
974  
1.21  
1.35  
1.51  
1.70  
920  
946  
974  
1001 1.82  
1029 2.04  
1.33  
1.46  
1.63  
946  
973  
1001 1.75  
1028 1.95  
1055 2.17  
1.44  
1.58  
973  
999  
1026 1.88  
1054 2.08  
1081 2.30  
1.55  
1.71  
999  
1.67  
1025 1.79 1050 1.90 1073 2.02 1098 2.14  
1048 1.96 1072 2.09 1096 2.22 1119 2.34  
1074 2.14 1099 2.27 1121 2.41 1143 2.55  
1103 2.34 1126 2.48 1148 2.62 1170 2.76  
1130 2.58 1154 2.72 1176 2.85 1199 3.01  
1024 1.83  
1051 2.01  
1079 2.20  
1105 2.43  
1002 1.91  
2.24 Nom kW Over-Sized Motor & High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-12a — Belt Drive Evaporator Fan Performance -TSC102AD - Downflow Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
Drive  
769  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
2 HP Standard Motor  
&
Low Static Drive  
2 HP Standard Motor  
&
2720  
3060  
3400  
3740  
4080  
-
-
-
-
-
-
-
-
-
-
-
-
613  
650  
689  
729  
770  
0.60  
0.74  
0.91  
1.10  
1.32  
655  
688  
724  
764  
804  
0.72  
0.85  
1.02  
1.23  
1.46  
695  
725  
759  
795  
834  
0.84  
0.98  
1.15  
1.35  
1.60  
733  
761  
792  
826  
864  
0.95  
1.11  
1.29  
1.49  
1.74  
1.08  
1.25  
1.43  
1.64  
1.88  
802 1.21  
828 1.38  
856 1.58  
887 1.79  
920 2.04  
833 1.34  
861 1.52  
887 1.72  
916 1.96  
948 2.20  
611  
651  
693  
738  
0.64  
0.79  
0.97  
1.19  
796  
825  
857  
892  
612  
659  
706  
0.68  
0.86  
1.08  
622  
671  
0.76  
0.96  
2 HP Standard Motor &  
Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
2 HP Standard Mtr & Drive  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
1.60  
RPM BHP  
1.70  
1.80  
1.90  
2.00  
CFM  
RPM BHP RPM BHP RPM BHP RPM BHP  
2 HP Std Motor & Hi Static Drive  
2720  
3060  
3400  
3740  
4080  
863  
891  
917  
945  
976  
1.48  
1.66  
1.87  
2.11  
2.38  
892  
919  
946  
974  
1.63  
1.81  
2.03  
2.28  
920  
946  
974  
1001 2.44  
1029 2.73  
1.78  
1.96  
2.18  
946  
973  
1001 2.34  
1028 2.61  
1055 2.91  
1.93  
2.12  
973  
999  
1026 2.52  
1054 2.78  
1081 3.09  
2.08  
2.29  
999  
2.24  
1025 2.39 1050 2.55 1073 2.71 1098 2.88  
1048 2.63 1072 2.80 1096 2.98 1119 3.14  
1074 2.86 1099 3.05 1121 3.23 1143 3.41  
1103 3.14 1126 3.32 1148 3.51 1170 3.71  
1130 3.45 1154 3.65 1176 3.83 1199 4.03  
1024 2.46  
1051 2.69  
1079 2.96  
1105 3.26  
1002 2.56  
3 HP Over-Sized Motor & Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
RT-PRC016-EN  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-13 — Belt Drive Evaporator Fan Performance -TSC102AD - Horizontal Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
125  
RPM  
150  
RPM  
175  
RPM  
1.50 Nom kW Standard Motor  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
1.50 Nom kW Std Mtr & Low Static Drive  
&
Drive  
4620  
5200  
5780  
6350  
6930  
-
-
-
-
646  
693  
743  
799  
857  
0.50  
0.64  
0.82  
1.04  
1.31  
689  
735  
781  
830  
883  
0.58  
0.73  
0.91  
1.12  
1.39  
734  
773  
819  
865  
913  
0.67  
0.82  
1.01  
1.23  
1.48  
781  
812  
853  
899  
945  
0.77  
0.92  
1.11  
1.34  
1.60  
826  
855  
886  
930  
977  
0.88  
1.03  
1.21  
1.45  
865  
897  
925  
960  
0.98  
1.15  
1.34  
1.56  
898 1.07  
934 1.27  
964 1.47 1000 1.60  
994 1.68 1028 1.82  
928 1.16  
969 1.38  
616  
675  
735  
796  
0.51  
0.68  
0.89  
1.14  
654  
711  
770  
828  
0.57  
0.75  
0.97  
1.23  
1.72 1006 1.84 1034 1.96 1061 2.08  
1.50 Nom kW Std Mtr  
& High Static Drive  
2.24 Nom kW Over-Sized  
Motor & High Static Drive  
External Static Pressure (Pascals)  
375 400  
RPM RPM  
275  
RPM  
300  
RPM  
325  
RPM  
350  
RPM  
425  
RPM  
450  
RPM  
475  
RPM kW  
500  
RPM kW  
m3/h  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
1.50 Nom kW Standard Motor & High Static Drive  
4620  
5200  
5780  
6350  
6930  
956  
999  
1034 1.73  
1063 1.96  
1093 2.23  
1.25  
1.49  
982  
1.33  
1008 1.42  
1052 1.68  
1094 1.97  
1129 2.26  
1157 2.53  
1033 1.51  
1078 1.78  
1120 2.08  
1158 2.40  
1188 2.70  
1056 1.60  
1101 1.88  
1145 2.20  
1185 2.53  
1218 2.86  
1079 1.69  
1124 1.98  
1168 2.31  
1210 2.66  
1245 3.01  
1102 1.78 1125 1.87 1146 1.95 1168 2.04  
1146 2.08 1168 2.18 1188 2.27 1209 2.37  
1191 2.42 1213 2.53 1234 2.63 1254 2.74  
1234 2.78 1256 2.90 1278 3.03 1299 3.15  
1026 1.58  
1067 1.86  
1098 2.11  
1125 2.38  
1273 3.16 1297 3.31  
-
-
-
-
2.24 Nom kW Over-Sized Motor & High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
1.50 kW - Fan Motor Heat (kW) = 1.178 x Fan kW + 0.464  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-13a — Belt Drive Evaporator Fan Performance -TSC102AD - Horizontal Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP RPM BHP RPM BHP RPM BHP  
2 HP Std Mtr & Low Static Drive  
2 HP Standard Motor  
&
Drive  
2720  
3060  
3400  
3740  
4080  
-
-
-
-
646  
693  
743  
799  
857  
0.67  
0.86  
1.10  
1.40  
1.76  
689  
735  
781  
830  
883  
0.78  
0.98  
1.22  
1.51  
1.86  
734  
773  
819  
865  
913  
0.90  
1.10  
1.36  
1.65  
1.99  
781  
812  
853  
899  
945  
1.04  
1.23  
1.49  
1.79  
2.15  
826  
855  
886  
930  
1.18  
1.39  
1.62  
1.94  
865  
897  
925  
960  
1.31  
1.55  
1.79  
2.09  
898 1.44  
934 1.70  
964 1.97 1000 2.14  
994 2.26 1028 2.44  
928 1.56  
969 1.85  
616  
675  
735  
796  
0.69  
0.92  
1.20  
1.53  
654  
711  
770  
828  
0.77  
1.01  
1.30  
1.65  
977  
2.30 1006 2.47 1034 2.63 1061 2.79  
3 HP Over-Sized Mtr & Drive  
2 HP Std Motor &  
Hi Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
2 HP Standard Motor  
1.20  
RPM BHP  
1.30  
RPM BHP  
High Static Drive  
1.40  
RPM BHP  
1.50  
RPM BHP  
1.60  
RPM BHP  
1.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
3 HP Over-Sized Motor Drive  
1102 2.38 1125 2.5 1146 2.62 1168 2.74  
1146 2.79 1168 2.92 1188 3.05 1209 3.18  
1191 3.24 1213 3.39 1234 3.53 1254 3.68  
1234 3.73 1256 3.89 1278 4.06 1299 4.23  
1.80  
1.90  
2.00  
CFM  
&
&
2720  
3060  
3400  
3740  
4080  
956  
999  
1.67  
1.99  
982  
1.79  
1008 1.91  
1052 2.26  
1094 2.64  
1129 3.03  
1157 3.40  
1033 2.03  
1078 2.39  
1120 2.79  
1158 3.21  
1188 3.62  
1056 2.14  
1101 2.52  
1145 2.94  
1185 3.39  
1218 3.83  
1079 2.26  
1124 2.66  
1168 3.09  
1210 3.56  
1245 4.03  
1026 2.12  
1067 2.49  
1098 2.84  
1125 3.19  
1034 2.32  
1063 2.63  
1093 2.99  
1273 4.24 1297 4.44  
-
-
-
-
3 HP Over-Sized Motor  
&
Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2 HP - Fan Motor Heat (MBH) = 3.000 x Fan BHP + 0.500  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
RT-PRC016-EN  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-14 — Belt Drive Evaporator Fan Performance -TSC120AD - Downflow Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
2.24 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
175  
RPM  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
2.24 Nom kW Standard Motor  
&
Drive  
5440  
6120  
6800  
7480  
8160  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
718  
764  
814  
864  
916  
0.72  
0.90  
1.11  
1.36  
1.64  
754  
797  
844  
894  
945  
0.82  
0.99  
1.21  
1.48  
1.77  
789  
829  
874  
922  
972  
0.93  
1.10  
1.32  
1.59  
1.90  
822  
860  
903  
948  
997  
1.03  
1.22  
1.44  
1.70  
856 1.14  
892 1.34  
932 1.56  
887 1.25  
922 1.46  
960 1.69  
731  
782  
834  
887  
0.81  
1.01  
1.24  
1.52  
715  
773  
833  
0.81  
1.04  
1.31  
747  
803  
861  
0.90  
1.14  
1.42  
741  
803  
0.95  
1.21  
975 1.82 1001 1.95  
2.02 1022 2.14 1046 2.27  
External Static Pressure (Pascals)  
375 400  
RPM RPM  
275  
RPM  
300  
RPM  
325  
RPM  
350  
RPM  
425  
RPM  
450  
RPM  
475  
RPM kW  
500  
RPM kW  
m3/h  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
2.24 Nom kW Standard Motor & Drive  
5440  
6120  
6800  
7480  
8160  
917  
951  
988  
1028 2.09  
1071 2.41  
1.36  
1.57  
1.82  
945  
979  
1015 1.95  
1053 2.23  
1095 2.55  
1.47  
1.69  
973  
1.60  
999  
1.72  
1024 1.84  
1059 2.07  
1093 2.35  
1128 2.66  
1166 3.02  
1048 1.97  
1082 2.20  
1117 2.48  
1152 2.81  
1189 3.17  
1072 2.10  
1107 2.34  
1142 2.63  
1176 2.95  
1212 3.33  
1095 2.23  
1130 2.49  
1164 2.76  
1198 3.10  
1117 2.37  
1152 2.63  
1187 2.91  
1221 3.25  
1140 3.36  
1173 3.71  
1209 4.11  
1007 1.82  
1042 2.08  
1078 2.38  
1119 2.70  
1033 1.94  
1068 2.21  
1103 2.52  
1142 2.86  
-
-
-
-
-
-
-
-
2.24 Nom kW Standard Motor & High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-14a — Belt Drive Evaporator Fan Performance -TSC120AD - Downflow Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
3 HP Standard Motor Drive  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
3 HP Standard Motor  
RPM BHP  
RPM BHP  
Low Static Drive  
RPM BHP  
RPM BHP  
&
&
3200  
3600  
4000  
4400  
4800  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
718  
764  
814  
864  
916  
0.97  
1.20  
1.49  
1.82  
2.20  
754  
797  
844  
894  
945  
1.10  
1.33  
1.63  
1.98  
2.38  
789  
829  
874  
922  
972  
1.25  
1.48  
1.77  
2.13  
2.55  
822  
860  
903  
948  
997  
1.38  
1.63  
1.93  
2.28  
856 1.53  
892 1.79  
932 2.09  
887 1.67  
922 1.95  
960 2.27  
731  
782  
834  
887  
1.08  
1.35  
1.67  
2.04  
715  
773  
833  
1.09  
1.40  
1.76  
747  
803  
861  
1.21  
1.53  
1.90  
741  
803  
1.27  
1.62  
975 2.44 1001 2.62  
2.71 1022 2.87 1046 3.04  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
1.20  
RPM BHP  
3 HP Standard Motor & Drive  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
1.60  
RPM BHP  
1.70  
1.80  
1.90  
2.00  
CFM  
RPM BHP RPM BHP RPM BHP RPM BHP  
3200  
3600  
4000  
4400  
4800  
917  
951  
988  
1028 2.81  
1071 3.23  
1.82  
2.11  
2.44  
945  
979  
1015 2.62  
1053 3.00  
1095 3.42  
1.97  
2.27  
973  
2.14  
999  
2.30  
1024 2.47  
1059 2.78  
1093 3.15  
1128 3.57  
1166 4.04  
1048 2.65  
1082 2.95  
1117 3.33  
1152 3.77  
1189 4.25  
1072 2.82 1095 3.00 1117 3.17 1140 3.36  
1107 3.14 1130 3.33 1152 3.52 1173 3.71  
1142 3.52 1164 3.70 1187 3.91 1209 4.11  
1007 2.43  
1042 2.79  
1078 3.19  
1119 3.62  
1033 2.60  
1068 2.97  
1103 3.38  
1142 3.83  
1176 3.96 1198 4.15 1221 4.36  
1212 4.46  
-
-
-
-
-
-
-
-
3 HP Standard Motor & High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
RT-PRC016-EN  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-15 — Belt Drive Evaporator Fan Performance -TSC120AD - Horizontal Configuration (SI)  
External Static Pressure (Pascals)  
25  
50  
75  
100  
RPM  
2.24 Nom kW Standard Motor & Low Static Drive  
125  
RPM  
150  
RPM  
175  
RPM  
2.24 Nom kW Standard Motor  
200  
RPM  
225  
RPM kW  
250  
RPM kW  
m3/h  
RPM  
kW  
RPM  
kW  
RPM  
kW  
kW  
kW  
kW  
kW  
kW  
&
Drive  
1.28 965 1.41 1000 1.53  
1.53 1002 1.67 1038 1.81  
5440  
6120  
6800  
7480  
8160  
-
-
691  
761  
833  
905  
977  
0.67  
0.91  
1.22  
1.58  
2.02  
730  
792  
860  
931  
0.75  
0.99  
1.29  
1.67  
771  
829  
890  
955  
0.84  
1.08  
1.38  
1.75  
807  
865  
923  
983  
0.94  
1.19  
1.50  
1.86  
844  
898  
956  
1014 1.99  
1074 2.42  
1.04  
1.30  
1.62  
886  
930  
986  
1.16  
1.41  
926  
965  
729  
802  
876  
950  
0.84  
1.13  
1.49  
1.91  
1.73 1015 1.85 1044 1.98 1077 2.12  
1045 2.12 1072 2.25 1098 2.37 1125 2.51  
1102 2.56 1131 2.71 1156 2.84 1181 2.98  
1002 2.11  
1025 2.20  
1048 2.30  
2.24 Nom kW Standard Motor & High Static Drive  
External Static Pressure (Pascals)  
375 400  
RPM RPM  
275  
RPM  
300  
RPM  
325  
RPM  
350  
RPM  
425  
RPM  
450  
RPM  
475  
RPM kW  
500  
RPM kW  
m3/h  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
kW  
2.24 Nom kW Std Mtr & Drive  
5440  
6120  
6800  
7480  
8160  
1029 1.64  
1072 1.95  
1111 2.28  
1152 2.65  
1205 3.12  
1057 1.75  
1106 2.10  
1143 2.43  
1182 2.81  
1229 3.27  
1084 1.86  
1134 2.22  
1174 2.58  
1211 2.97  
1108 1.96  
1160 2.35  
1204 2.74  
1241 3.14  
1132 2.06  
1185 2.47  
1232 2.90  
1270 3.31  
1155 2.17  
1209 2.59  
1260 3.05  
1177 2.27 1198 2.37 1219 2.48 1239 3.46  
1231 2.70 1252 2.82 1274 2.94 1295 4.10  
1283 3.18 1306 3.32  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.24 Nom kW Standard Motor & High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
2.24 kW - Fan Motor Heat (kW) = 1.138 x Fan kW + 0.139  
Table PD-15a — Belt Drive Evaporator Fan Performance -TSC120AD - Horizontal Configuration (IP)  
External Static Pressure (Inches of Water)  
.10  
.20  
.30  
.40  
.50  
.60  
.70  
RPM BHP RPM BHP RPM BHP RPM BHP  
Drive  
926  
965  
.80  
.90  
1.00  
CFM  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
RPM BHP  
3 HP Standard Motor & Low Static Drive  
3 HP Standard Motor  
&
3200  
3600  
4000  
4400  
4800  
-
-
691  
761  
833  
905  
977  
0.89  
1.22  
1.63  
2.12  
2.70  
730  
792  
860  
931  
1.00  
1.32  
1.73  
2.24  
771  
829  
890  
955  
1.13  
1.45  
1.86  
2.35  
807  
865  
923  
983  
1.26  
1.60  
2.01  
2.49  
844  
898  
956  
1.39  
1.74  
2.17  
886  
930  
986  
1.55  
1.89  
1.72  
965 1.89 1000 2.06  
2.06 1002 2.24 1038 2.43  
729  
802  
876  
950  
1.13  
1.52  
1.99  
2.56  
2.32 1015 2.48 1044 2.65 1077 2.85  
1045 2.84 1072 3.01 1098 3.18 1125 3.36  
1014 2.66  
1074 3.24  
1002 2.84  
1025 2.96  
1048 3.08  
1102 3.43  
1131 3.63  
1156 3.81  
1181 4.00  
3 HP Standard Motor  
&
High Static Drive  
External Static Pressure (Inches of Water)  
1.10  
RPM BHP  
3 HP Std Mtr & Drive  
1.20  
RPM BHP  
1.30  
RPM BHP  
1.40  
RPM BHP  
1.50  
RPM BHP  
1.60  
RPM BHP  
1.70  
1.80  
1.90  
2.00  
CFM  
RPM BHP RPM BHP RPM BHP RPM BHP  
3200  
3600  
4000  
4400  
4800  
1029 2.20  
1072 2.62  
1111 3.05  
1152 3.55  
1205 4.19  
1057 2.35  
1084 2.49  
1134 2.98  
1174 3.47  
1211 3.99  
1108 2.63  
1160 3.15  
1204 3.68  
1241 4.21  
1132 2.77  
1185 3.31  
1232 3.88  
1270 4.44  
1155 2.91  
1209 3.47  
1260 4.09  
1177 3.05 1198 3.18 1219 3.32 1239 3.46  
1231 3.63 1252 3.78 1274 3.94 1295 4.10  
1106 2.81  
1143 3.26  
1182 3.76  
1229 4.39  
1283 4.27 1306 4.46  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3 HP Standard Motor  
&
High Static Drive  
Notes:  
Factory Supplied Motors, In Com m ercial Equipm ent, Are Definite Purpose Motors, Specifically Designed And Tested To  
Operate Reliably And Continuously At All Cataloged Conditions. Using The Full Horsepower Range Of Our Fan Motors  
As Shown In Our Tabular Data Will Not Result In Nuisance Tripping Or Prem ature Motor Failure. Our Products Warranty  
Will Not Be Affected.  
Data Includes Pressure Drop Due To Wet Coils And Filters.  
3 HP - Fan Motor Heat (MBH) = 2.900 x Fan BHP + 0.475  
RT-PRC016-EN  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-16 — Standard Motor & Sheave/Fan Speed (RPM)  
Unit  
6 Turns  
Open  
N/A  
N/A  
N/A  
5 Turns  
Open  
898  
698  
752  
4 Turns  
Open  
967  
751  
806  
3 Turns  
Open  
1036  
806  
860  
786  
2 Turns  
Open  
1105  
859  
914  
835  
1 Turns  
Open  
1174  
913  
968  
885  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Closed  
1243  
967  
1020  
934  
N/A  
N/A  
688  
782  
737  
838  
894  
950  
1006  
1062  
Factory set at 3 turns open  
Table PD-17 — Standard Motor & Low Static Drive Accessory Sheave/Fan Speed (RPM)  
Unit  
6 Turns  
Open  
N/A  
N/A  
N/A  
5 Turns  
Open  
691  
537  
671  
4 Turns  
Open  
760  
590  
714  
3 Turns  
Open  
829  
644  
757  
2 Turns  
Open  
898  
698  
800  
1 Turns  
Open  
967  
752  
843  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Closed  
1036  
806  
886  
811  
N/A  
N/A  
629  
717  
664  
754  
701  
799  
737  
844  
773  
885  
922  
Factory set at 3 turns open  
Table PD-18 — Standard Motor & High Static Drive Accessory Sheave/Fan Speed (RPM)  
Unit  
6 Turns  
Open  
N/A  
N/A  
1020  
936  
5 Turns  
Open  
1243  
967  
1073  
981  
4 Turns  
Open  
1311  
1021  
1127  
1032  
1174  
3 Turns  
Open  
1379  
1075  
1181  
1083  
1229  
2 Turns  
Open  
1450  
1128  
1235  
1134  
1285  
1 Turns  
Open  
1515  
1183  
1289  
1182  
1341  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Closed  
1588  
1235  
N/A  
N/A  
N/A  
1062  
1118  
Factory set at 3 turns open  
Table PD-19 — Oversized Motor & Drive Sheave/Fan Speed (RPM)  
Unit  
6 Turns  
Open  
N/A  
1112  
N/A  
5 Turns  
Open  
967  
1182  
971  
4 Turns  
Open  
1021  
1252  
1041  
N/A  
3 Turns  
Open  
1075  
1322  
1111  
N/A  
2 Turns  
Open  
1128  
1392  
1181  
N/A  
1 Turns  
Open  
1183  
1460  
1251  
N/A  
Model No.  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Closed  
1235  
N/A  
1321  
N/A  
N/A  
N/A  
Factory set at 3 turns open  
Table PD-20 — Sound Power Level - dB (ref. 10 -12 Watts)  
Unit  
Octave Center Frequency  
Overall  
dBA  
80  
85  
85  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Note:  
63  
84  
83  
83  
83  
83  
125  
91  
90  
90  
89  
86  
250  
79  
86  
86  
84  
80  
500  
77  
82  
83  
81  
77  
1000  
74  
79  
80  
77  
2000  
71  
4000  
8000  
63  
63  
64  
62  
68  
70  
71  
69  
66  
75  
75  
72  
69  
83  
79  
73  
60  
Tests follow ARI 270-95  
RT-PRC016-EN  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-21 — Static Pressure Drops Through Accessories - (Pascals)  
Economizer  
Electric Heater  
OA/RA Dampers2  
Accessory (kW)3  
Unit  
Model No.  
TSC060AD  
Airflow  
(m3/h)  
2720  
3400  
4080  
3260  
4080  
4890  
4080  
5100  
6120  
4620  
5780  
6930  
5440  
6800  
8160  
Standard Pleated Filters  
100% OA  
100% RA  
100% OA  
100% RA  
Filters1  
25  
(50 mm)  
37  
Downflow  
Horizontal  
9
11  
17  
25  
-
13-27  
13  
21  
30  
5
40  
-
-
-
-
30  
46  
64  
25  
27  
33  
27  
35  
52  
31  
47  
75  
42  
65  
85  
11  
17  
26  
2
5
10  
5
12  
17  
7
15  
17  
12  
17  
22  
30  
46  
64  
15  
20  
25  
20  
30  
62  
22  
45  
77  
35  
75  
87  
4
6
9
5
5
37  
55  
55  
72  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Notes:  
10  
17  
15  
22  
-
8
-
22  
30  
10  
5
-
-
13  
8
-
-
15  
22  
25  
32  
12  
20  
10  
15  
22  
12  
20  
25  
-
-
-
16  
25  
6
-
-
-
35  
45  
12  
20  
20  
27  
-
-
-
-
10  
15  
9
14  
20  
-
-
10  
17  
26  
30  
40  
17  
25  
27  
37  
40  
50  
-
1. Tested with standard filters. The TSC060AD has 25 m m (1 inch) standard fiters. The TSC072AD - 120AD has 50 m m (2 inch) standard filters.  
The difference in pressure drop should be considered when utilizing optional 50 m m (2 inch) pleated filters.  
2. OA = Outside Air and RA = Return Air  
3. Nom inal kW ratings at 415 V  
Table PD-21a — Static Pressure Drops Through Accessories - (Inches of Water Column)  
Economizer  
Electric Heater  
OA/RA Dampers2  
Accessory (kW)3  
Unit  
Model No.  
TSC060AD  
Airflow  
(CFM)  
1600  
2000  
2400  
1920  
2400  
2880  
2400  
3000  
3600  
2720  
3400  
4080  
3200  
4000  
4800  
Standard Pleated Filters  
100% OA  
100% RA  
100% OA  
100% RA  
Filters1  
0.10  
0.15  
0.22  
0.04  
0.06  
0.09  
0.06  
0.10  
0.14  
0.05  
0.08  
0.12  
0.07  
0.11  
0.16  
(2 inch)  
0.15  
0.22  
0.29  
0.07  
0.09  
0.12  
0.09  
0.13  
0.18  
0.08  
0.11  
0.16  
0.10  
0.15  
0.20  
Downflow  
Horizontal  
9
13-27  
0.053  
0.083  
0.120  
0.021  
0.034  
0.052  
0.034  
0.063  
0.102  
0.026  
0.041  
0.059  
0.036  
0.056  
0.081  
40  
-
-
-
-
-
-
-
-
-
-
-
0.12  
0.18  
0.26  
0.10  
0.11  
0.13  
0.11  
0.14  
0.21  
0.12  
0.19  
0.30  
0.17  
0.26  
0.34  
0.04  
0.07  
0.10  
0.01  
0.02  
0.04  
0.02  
0.05  
0.07  
0.03  
0.06  
0.07  
0.05  
0.07  
0.09  
0.12  
0.18  
0.26  
0.06  
0.08  
0.10  
0.08  
0.12  
0.25  
0.09  
0.18  
0.31  
0.14  
0.30  
0.35  
0.01  
0.02  
0.04  
0.02  
0.02  
0.04  
0.02  
0.05  
0.08  
0.04  
0.06  
0.09  
0.05  
0.08  
0.10  
0.045  
0.070  
0.100  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Notes:  
-
-
-
-
-
-
-
-
-
-
-
-
-
0.042  
0.070  
0.106  
1. Tested with standard filters. The TSC060AD has 25 m m (1 inch) standard fiters. The TSC072AD - 120AD has 50 m m (2 inch) standard filters.  
The difference in pressure drop should be considered when utilizing optional 50 m m (2 inch) pleated filters.  
2. OA = Outside Air and RA = Return Air  
3. Nom inal kW ratings at 415 V  
Table PD-22 - Electric Heater Voltage Correction Factors (Apply to Auxiliary Electric Heat  
Capacity)  
Nominal  
Voltage  
Distribution  
Voltage  
380  
Capacity  
Multipiler  
0.84  
415  
400  
0.93  
415  
1.00  
RT-PRC016-EN  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-23 — Auxiliary Electric Heat Capacity (SI)  
Total2  
Stage 1  
Stage 2  
Unit  
Unit  
Model No.  
Voltage  
KW  
No. Stages  
KW  
KW  
7.5 / 9.0  
2
2
2
1
2
2
1
2
2
2
2
2
2
2
3.75 / 4.5  
5.45 / 6.5  
3.75 / 4.5  
5.45 / 6.5  
5.45 / 6.5  
—-  
5.6 / 6.7  
11.3 / 13.5  
—-  
5.6 / 6.7  
11.3 / 13.5  
5.6 / 6.7  
11.3 / 13.5  
5.6 / 6.7  
11.3 / 13.5  
22.5 / 26.9  
TSC060AD  
TSC072AD  
380-415/50/3  
380-415/50/3  
10.9 / 13.0  
14.4 / 17.2  
11.3 / 13.5  
16.9 / 20.2  
22.6 / 26.9  
11.3 / 13.5  
16.9 / 20.2  
22.6 / 26.9  
16.9 / 20.2  
22.6 / 26.9  
16.9 / 20.2  
22.6 / 26.9  
33.9 / 40.4  
8.95 / 10.7  
11.3 / 13.5  
11.3 / 13.5  
11.3 / 13.5  
11.3 / 13.5  
11.3 / 13.5  
11.3 / 13.5  
11.3 / 13.6  
11.3 / 13.7  
11.3 / 13.8  
11.3 / 13.9  
11.3 / 13.10  
TSC090AD  
TSC102AD  
380-415/50/3  
380-415/50/3  
TSC120AD  
380-415/50/3  
Notes:  
1. Does not include indoor fan power or heat  
2. Heaters are rated at 380V / 415V. For other than rated voltage, CAP=(Voltage/Rated Voltage)2 x Rated Cap.  
Table PD-23A — Auxiliary Electric Heat Capacity (IP)  
Total2  
Stage 1  
Stage 2  
Unit  
Unit  
Model No.  
Voltage  
MBH  
26 / 31  
38 / 45  
50 / 59  
39 / 47  
58 / 69  
78 / 92  
39 / 47  
58 / 69  
78 / 92  
58 / 69  
78 / 92  
58 / 69  
78 / 92  
116 / 138  
No. Stages  
MBH  
13 / 16  
19 / 23  
31 / 37  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
39 / 47  
MBH  
13 / 16  
19 / 23  
19 / 23  
—-  
20 / 23  
39 / 47  
—-  
20 / 23  
39 / 47  
20 / 23  
39 / 47  
20 / 23  
39 / 47  
77 / 92  
2
2
2
1
2
2
1
2
2
2
2
2
2
2
TSC060AD  
TSC072AD  
380-415/50/3  
380-415/50/3  
TSC090AD  
TSC102AD  
380-415/50/3  
380-415/50/3  
TSC120AD  
380-415/50/3  
Notes:  
1. Does not include indoor fan power or heat  
2. Heaters are rated at 380 / 415V. For other than rated voltage, CAP=(Voltage/Rated Voltage)2 x Rated Cap.  
RT-PRC016-EN  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Perform ance  
Data  
Table PD-24 — Air Temperature Rise Across Electric Heaters (Degrees C)  
kW  
3400 m3/h  
TSC060AD  
6.6 / 7.9  
9.6 / 11.4  
—-  
4100 m3/h  
TSC072AD  
—-  
—-  
8.3 / 9.9  
—-  
12.4 / 14.8  
16.5 / 19.7  
—-  
5100 m3/h  
TSC090AD  
—-  
—-  
6.6 / 7.9  
—-  
9.9 / 11.8  
13.2 / 15.7  
—-  
5800 m3/h  
TSC102AD  
—-  
6800 m3/h  
TSC120AD  
—-  
380V / 415V  
07.5 / 09.0  
10.9 / 13.0  
11.3 / 13.5  
14.4 / 17.2  
16.9 / 20.2  
22.6 / 26.9  
33.8 / 40.4  
Voltage  
Stages  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
2
2
1
2
2
2
2
—-  
—-  
—-  
—-  
—-  
—-  
12.6 / 15.1  
—-  
8.7 / 10.4  
11.7 / 13.9  
—-  
7.4 / 8.9  
9.9 / 11.8  
14.8 / 17.7  
—-  
—-  
Note:  
For m inim um design airflow, see perform ance table for each unit.  
To calculate tem p rise at differrent airflow, use following form ula:  
Tem p. Rise (C0) across Elect Htr = (kW x 2985)/( m 3/h)  
Table PD-24A — Air Temperature Rise Across Electric Heaters (Degrees F)  
kW  
2000 CFM  
TSC060AD  
11.9 / 14.2  
17.2 / 20.5  
—-  
2400 CFM  
TSC072AD  
—-  
—-  
14.9 / 17.8  
—-  
22.3 / 26.6  
29.8 / 35.4  
—-  
3000 CFM  
TSC090AD  
—-  
—-  
11.9 / 14.2  
—-  
17.8 / 21.3  
23.8 / 28.3  
—-  
3400 CFM  
TSC102AD  
—-  
4000 CFM  
TSC120AD  
—-  
380V / 415V  
07.5 / 09.0  
10.9 / 13.0  
11.3 / 13.5  
14.4 / 17.2  
16.9 / 20.2  
22.6 / 26.9  
33.8 / 40.4  
Voltage  
Stages  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
380-415/50/3  
2
2
1
2
2
2
2
—-  
—-  
—-  
—-  
—-  
—-  
22.8 / 27.2  
—-  
15.7 / 18.8  
21.0 / 25.0  
—-  
13.4 / 16.0  
17.9 / 21.3  
26.7 / 31.9  
—-  
—-  
Note:  
For m inim um design airflow, see perform ance table for each unit.  
To calculate tem p rise at differrent airflow, use following form ula:  
Tem p. Rise (F0) across Elect Htr = (kW x 3414)/(1.08 x CFM)  
RT-PRC016-EN  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Zone Controls  
Non-programmable manual auto  
changeover with digital LCD Display —  
Auto, heat, cool or off mode selection  
button. Auto or off fan bottom. Status  
indication LCD indicators — System on,  
heat, cool, or service.  
Zone Sensors  
Conventional Thermostats  
Zone Sensors are the building  
occupants comfort control devices for  
Precedentunits with the ReliaTel  
control. The zone sensor offering  
operates with the Reliatel  
Conventional Thermostats are the  
building occupants comfort control  
devises when a generic thermostat is  
desired.  
Manual  
microprocessor  
Changeover —  
One Heat, One  
Cool Thermostat.  
Heat, Cool or Off  
System Switch.  
Fan Auto or On  
Switch. Set Point  
Dial. Adjustable  
Heat Anticipator.  
Manual Changeover — Heat, Cool or Off  
System Switch. Fan Auto or Off Switch.  
One  
temperature  
setpoint lever.  
Automatic Changeover — One Heat,  
Two Cool Thermostat. Off, Auto System  
Switch. Auto/On Fan Switch.  
Programmable Night Setback — Auto  
or manual changeover with seven-day  
programming. Keyboard selection of  
Heat, Cool, Fan, Auto, or On.  
Manual/Automatic Changeover —Auto,  
Heat, Cool or Off System Switch. Fan  
Auto or Off  
All programmable sensors have  
Switch. Two  
temperature  
setpoint  
levers. Optional  
Status Indication  
LED lights,  
System On,  
Heat, Cool, or  
Programmable Electronic Night Setback  
Thermostat — Heating setback and  
cooling setup with 7-day, programming  
capability. Available in two-stage  
heating/cooling or one-stage heating/  
cooling versions with automatic  
changeover.  
Service.  
System On, Heat, Cool, Service LED/  
indicators as standard. Night Setback  
Sensors have one (1) Occupied, one (1)  
Unoccuped, and two (2) Override  
programs per day.  
Integrated ComfortSystem —  
Sensor(s) available with optional  
temperature  
Remote Sensor — Sensor(s) available  
for all zone sensors to provide  
remote sensing  
capabilities.  
adjustment and  
override buttons  
to provide  
central control  
through a Trane  
Integrated  
Comfort™  
system.  
RT-PRC016-EN  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electrical  
Data  
Table ED-1 — Unit Wiring  
Standard Indoor Fan Motor  
Oversized Indoor Fan Motor  
Unit  
Minimum  
Maximum Fuse  
Minimum  
Maximum Fuse  
Unit  
Operating  
Voltage Range  
342-456  
Circuit  
Ampacitiy  
17.7  
23.2  
24.8  
Size Or Maximum  
Circuit  
Ampacitiy  
17.7  
24.2  
26.5  
Size Or Maximum  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Circuit Breaker1  
Circuit Breaker1  
25  
35  
35  
35  
40  
25  
35  
35  
35  
40  
342-456  
342-456  
342-456  
342-456  
26.8  
31.2  
28.5  
31.2  
Notes:  
1. All units to be installed under local codes  
Table ED-2 — Unit Wiring With Electric Heat Single Point Connection — 380-415 Volts  
Standard Indoor Fan Motor  
Oversized Indoor Fan Motor  
Minimum  
Circuit  
Maximum Fuse  
Minimum  
Circuit  
Maximum Fuse  
Size Or Maximum  
Circuit Breaker1  
25 / 25  
Unit  
Model No.  
TSC060AD  
Heater  
Model No.  
Heater2  
MBH  
Control  
Stages  
Size Or Maximum  
Circuit Breaker1  
25 / 25  
kW Rating  
7.5 / 9.0  
Ampacitiy  
19.8 / 21.0  
26.1 / 28.0  
32.8 / 35.3  
26.9 / 28.9  
37.5 / 40.5  
48.3 / 52.1  
28.1 / 30.1  
38.8 / 41.8  
49.5 / 53.4  
38.8 / 41.8  
49.5 / 53.4  
40.9 / 43.9  
51.6 / 55.5  
73.1 / 79.0  
Ampacitiy  
19.8 / 21.0  
26.1 / 28.0  
32.8 / 35.3  
28.1 / 30.1  
38.8 / 41.8  
49.5 / 53.4  
30.3 / 32.3  
40.9 / 43.9  
51.6 / 55.5  
40.9 / 43.9  
51.6 / 55.5  
40.9 / 43.9  
51.6 / 55.5  
73.1 / 79.0  
BAYHTRR412A  
BAYHTRR418A  
BAYHTRR423A  
BAYHTRS418A  
BAYHTRS427A  
BAYHTRS436A  
BAYHTRS418A  
BAYHTRS427A  
BAYHTRS436A  
BAYHTRT427A  
BAYHTRT436A  
BAYHTRT427A  
BAYHTRT436A  
BAYHTRT454A  
26 / 31  
38 / 45  
50 / 59  
39 / 47  
58 / 69  
78 / 92  
39 / 47  
58 / 69  
78 / 92  
58 / 69  
78 / 92  
58 / 69  
78 / 92  
116 / 138  
2
2
2
1
2
2
1
2
2
2
2
2
2
2
10.9 / 13.0  
14.4 / 17.2  
11.3 / 13.5  
16.9 / 20.2  
22.6 / 26.9  
11.3 / 13.5  
16.9 / 20.2  
22.6 / 26.9  
16.9 / 20.2  
22.6 / 26.9  
16.9 / 20.2  
22.6 / 26.9  
33.8 / 40.4  
30 / 30  
35 / 40  
35 / 35  
40 / 45  
50 / 60  
35 / 35  
40 / 45  
50 / 60  
40 / 45  
50 / 60  
45 / 45  
60 / 60  
30 / 30  
35 / 40  
35 / 35  
40 / 45  
50 / 60  
35 / 35  
45 / 45  
60 / 60  
45 / 45  
60 / 60  
45 / 45  
60 / 60  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
80 / 80  
80 / 80  
Notes:  
1. All units to be installed under local codes  
2. kW and MBH shown for 380V / 415V  
Table ED-3 — Electrical Characteristics - Evaporator Fan Motor - 50 Hz  
Standard Evaporator Fan Motor  
Oversized Evaporator Fan Motor  
Unit  
Amps  
Amps  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
No.  
1
1
1
1
Volts  
Phase  
HP  
1.5  
1.5  
2.0  
2.0  
3.0  
FLA  
4.3  
4.3  
5.3  
5.3  
7.0  
LRA  
25.3  
25.3  
36.4  
36.4  
57.0  
No.  
Volts  
-
380-415  
380-415  
380-415  
-
Phase  
HP  
-
2.0  
3.0  
3.0  
-
FLA  
-
5.3  
7.0  
7.0  
-
LRA  
-
36.4  
57.0  
57.0  
-
380-415  
380-415  
380-415  
380-415  
380-415  
3
3
3
3
3
-
1
1
1
-
-
3
3
3
-
1
Table ED-4 — Electrical Characteristics - Compressor Motor and Condenser Motor - 50 Hz  
Compressor Motor  
Condenser Fan Motor  
Unit  
Amps  
Amps  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
No.  
1
1
1
2
Volts  
Phase  
HP1  
5.7  
7.5  
8.3  
6.0/3.8  
6.0/4.8  
RPM  
2875  
2875  
2875  
2875  
2875  
RLA1  
9.5  
12.7  
13.20  
9.3/6.9  
9.9/8.5  
LRA1  
74.00  
95.00  
No.  
Phase  
HP  
FLA  
1.9  
2.8  
2.8  
2.8  
2.8  
LRA  
2.8  
7.1  
7.1  
7.1  
380-415  
380-415  
380-415  
380-415  
380-415  
3
3
3
3
3
1
1
1
1
1
1
1
1
1
1
0.40  
0.75  
0.75  
0.75  
0.75  
100.00  
74.0/48.0  
74.0/61.8  
2
7.1  
Note:  
1. Com p1/Com p2  
RT-PRC016-EN  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
J obsite  
Connections  
Zone Sensors — Typical Number Of Wires  
DISCONNECT  
SWITCH  
(BY OTHERS)  
A — Manual Changeover . . . . . . . . . . . . . . . . . 4  
Manual/Auto Changeover . . . . . . . . . . . . . 5  
Manual/Auto Changeover with  
ZONE SENSOR  
OR THERMOSTAT  
Status Indication LEDs . . . . . . . . . . . . . 10  
Programmable Night Setback with  
Status Indication LEDs . . . . . . . . . . . . . . 7  
ROOFTOP  
UNIT  
Thermostats — Typical Number of Wires  
A — 3 wires, 24-volts, Cooling Only  
4 wires, 24-volts, with Electric Heat  
B — 3 Power Wires + 1 Ground Wire (three phase)  
2 Power Wires + 1 Ground Wire (single phase)  
For specific wiring inform ation, see the installation instructions.  
All wiring except power wires is low voltage.  
All custom er supplied wiring to be copper and m ust conform to NEC or CEC and local electrical codes. Wiring shown dotted is to be furnished and installed by the custom er.  
RT-PRC016-EN  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC060  
All dimensions are in inches/millimeters.  
TSC060  
RT-PRC016-EN  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC060  
All dimensions are in inches/millimeters.  
TSC060 — Downflow Airflow Supply/Return  
TSC060 — Horizontal Airflow Supply/Return  
TSC060 — Unit Clearance and Roof Opening  
RT-PRC016-EN  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC060  
All dimensions are in inches/millimeters.  
TSC060 — Roof Curb  
TSC060 — Downflow Duct Connections — Field Fabricated  
RT-PRC016-EN  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC072-120  
All dimensions are in inches/millimeters.  
TSC072-090  
TSC102-120  
RT-PRC016-EN  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC072-120  
All dimensions are in inches/millimeters.  
TSC072-120 — Downflow Airflow Supply  
and Return  
TSC072-120 — Horizontal Airflow Supply  
and Return  
TSC072-120 — Unit Clearance and Roof  
Opening  
RT-PRC016-EN  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dim ensional  
Data  
TSC072-120  
All dimensions are in inches/millimeters.  
TSC072-120 — Roof Curb  
TSC072-120 — Downflow Duct Connections —  
Field Fabricated  
ALL FLANGES 1 1/4” (31 MM)  
RT-PRC016-EN  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TSC060  
Options/Accessories  
Dim ensional  
Data  
All dimensions are in inches/millimeters.  
TSC060 — Barometric Relief Damper Hood  
TSC060 — Economizer , Manual or Motorized Fresh Air Damper  
TSC060 — Swing Diameter for Hinged Doors Option  
RT-PRC016-EN  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TSC072-120  
Options/Accessories  
Dim ensional  
Data  
All dimensions are in inches/millimeters.  
TSC072-120 — Economizer and Barometric  
Relief Damper Hoods  
TSC072-120 — Swing Diameter for  
Hinged Door(s) Option  
RT-PRC016-EN  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Weights  
Table W-1 - Maximum Unit and Corner Weights and Center of Gravity Dimensions (SI)  
Maximum Weights(2) (kg)  
Corner Weights(1) (kg)  
Center of Gravity (mm)  
Unit  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Shipping(2)  
259  
Net(2)  
235  
326  
389  
405  
445  
A
75  
107  
131  
133  
147  
B
56  
83  
101  
106  
115  
C
D
56  
78  
89  
94  
Length  
790  
970  
970  
990  
Width  
480  
560  
530  
560  
48  
58  
67  
72  
81  
365  
428  
445  
485  
104  
990  
560  
Notes:  
(1) Corner weights are given for inform ation only. All m odels m ust be supported continuously by a curb or equivalent fram e support.  
(2) Weights are approxim ate.  
Table W-1a - Maximum Unit and Corner Weights and Center of Gravity Dimensions (IP)  
Maximum Weights (lbs)  
Corner Weights(1) (lbs)  
Center of Gravity (in)  
Unit  
Model No.  
TSC060AD  
TSC072AD  
TSC090AD  
TSC102AD  
TSC120AD  
Shipping(2)  
572  
805  
944  
980  
1069  
Net  
518  
718  
857  
893  
982  
A
B
C
D
Length  
31  
38  
38  
39  
Width  
165  
235  
289  
294  
323  
124  
182  
222  
233  
253  
105  
128  
148  
159  
178  
124  
173  
197  
207  
229  
19  
22  
21  
22  
22  
39  
Notes:  
(1) Corner weights are given for inform ation only. All m odels m ust be supported continuously by a curb or equivalent fram e support.  
(2) Weights are approxim ate.  
Table W-2a - Accessory Net Weights(1) (2) (lbs)  
Table W-2 - Accessory Net Weights(1) (2) (kg)  
Net Weights(2)  
Net Weights(2)  
TSC072-120  
Accessory(3)  
TSC060  
TSC072-120  
Accessory(3)  
TSC060  
Economizer  
26  
7
20  
16  
70  
5
12  
10  
15  
36  
10  
30  
26  
115  
8
20  
12  
30  
Economizer  
12  
3
9
7
32  
2
5
5
7
16  
5
14  
12  
52  
4
9
5
14  
Barometric Relief  
Motorized Outside Air Damper  
Manual Outside Air Damper  
Roof Curb  
Oversized Motor  
Coil Guards  
Barometric Relief  
Motorized Outside Air Damper  
Manual Outside Air Damper  
Roof Curb  
Oversized Motor  
Coil Guards  
Hinged Doors  
Electric Heaters  
Hinged Doors  
Electric Heaters  
Notes:  
Notes:  
(1) Weights for options not listed are < 5 lbs.  
(1) Weights for options not listed are < 3 kg.  
2) Net weight should be added to unit weight when ordering factory-installed  
accessories.  
(3) Som e accessories not available on all units.  
(2) Net weight should be added to unit weight when ordering factory-installed  
accessories.  
(3) Som e accessories not available on all units.  
RT-PRC016-EN  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mechanical  
Specifications  
Outdoor Fans  
Unit Top  
General  
The outdoor fan shall be direct-drive,  
statically and dynamically balanced,  
draw-through in the vertical discharge  
position. The fan motor shall be  
permanently lubricated and shall have  
built-in thermal overload protection.  
The top cover shall be one piece  
construction or where seams exist, it  
shall be double-hemmed and gasket-  
sealed. The ribbed top adds extra  
strength and prevents water from  
pooling on unit top.  
The units shall be convertible airflow.  
The operating range shall be between  
46°C and -18°C (115°F and 0°F) in  
cooling as standard from the factory for  
all units. All units shall be factory  
assembled, internally wired, fully  
charged with R-22, and 100 percent run  
tested to check cooling operation, fan  
and blower rotation, and control  
sequence before leaving the factory.  
Wiring internal to the unit shall be  
colored and numbered for simplified  
identification.  
Indoor Fan  
Filters  
All units shall have belt drive motors.  
Units with belt drive motors shall have  
an adjustable idler-arm assembly for  
quick-adjustment to fan belts and motor  
sheaves. All motors shall be thermally  
protected. Oversized motors shall be  
available for high static operations.  
One inch, throwaway filters shall be  
standard on all 5 ton units. The filter rack  
can be converted to two inch capability.  
50 mm (2 inch) filters shall be factory  
supplied on all 6-10 ton units. Optional  
50 mm (2 inch) pleated filters shall be  
available.  
Casing  
Unit casing shall be constructed of zinc  
coated, heavy gauge, galvanized steel.  
Exterior surfaces shall be cleaned,  
phosphatized, and finished with a  
weather-resistant baked enamel finish.  
Cabinet construction shall allow for all  
maintenance on one side of the unit.  
Service panels shall have lifting  
handles and be removed and  
reinstalled by removing only a single  
fastener while providing a water and  
air tight seal. All exposed vertical  
panels and top covers in the indoor air  
section shall be insulated with a  
cleanable foil-faced, fire-retardent  
permanent, odorless glass fiber  
material. The base of the unit shall be  
insulated with 13 mm, 16 kg (1/2 inch,  
1 pound) density foil-faced, closed-cell  
material. All insulation edges shall be  
either captured or sealed.The units  
base pan shall have no penetrations  
within the perimeter of the curb other  
than the raised 29 mm (11/8 inch high  
downflow supply/return openings to  
provide an added water integrity  
precaution, if the condensate drain  
backs up. The base of the unit shall  
have provisions for forklift and crane  
lifting, with forklift capabilities on three  
sides of the unit.  
Controls  
Compressors  
All units shall have direct-drive,  
Unit shall be completely factory-wired  
with necessary controls and contactor  
pressure lugs or terminal block for  
power wiring. Units shall have single  
point power connection as standard.  
Unit shall provide an external location  
for mounting a fused disconnect device.  
hermetic, scroll type compressors with  
centrifugal type oil pumps. Motor shall  
be suction gas-cooled and shall have a  
voltage utilization range of plus or minus  
10 percent of unit nameplate voltage.  
Internal overloads shall be provided with  
the scroll compressors. Low and high  
pressure switches shall be standard.  
Microprocessor controls provide for all  
24 volt control functions. The resident  
control algorithms shall make all  
heating, cooling, and/or ventilating  
decisions in response to electronic  
signals from sensors measuring indoor  
and outdoor temperatures. The control  
algorithm maintains accurate  
temperature control, minimizes drift  
from set point, and provides better  
building comfort. A centralized  
Microprocessor shall provide anti-short  
cycle timing and time delay between  
compressors to provide a higher level of  
machine protection.  
Refrigerant Circuits  
Service pressure ports, and refrigerant  
line filter driers are factory-installed as  
standard. An area shall be provided for  
replacement suction line driers.  
Evaporator and Condenser Coils  
Internally finned, 8 mm (5/16”) copper  
tubes mechanically bonded to a  
configured aluminum plate fin shall be  
standard. Coils shall be leak tested at the  
factory to ensure the pressure integrity.  
The evaporator coil and condenser coil  
shall be leak tested to 1375 kPa (200  
psig) and pressure tested to 3100 kPa  
(450 psig). The condenser coil shall have  
a patent pending 1 + 1 + 1 hybrid coil  
designed with slight gaps for ease of  
cleaning. A removeable, reversible,  
double-sloped condensate drain pan  
with provision for through the base  
condensate drain is standard.  
RT-PRC016-EN  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mechanical  
Specifications  
Economizer This accessory shall be  
either field or factory-installed and shall  
be available with or without barometric  
relief. The assembly includes fully  
modulating 0-100 percent motor and  
dampers, minimum position setting,  
preset linkage, wiring harness with plug,  
spring return actuator and fixed dry bulb  
control. The barometric relief shall  
provide a pressure operated damper that  
shall be gravity closing and shall prohibit  
entrance of outside air during the  
equipment “off” cycle. Optional solid  
state or differential enthalpy control shall  
be available for either factory or field  
installation. The factory-installed  
Motorized Outside Air Dampers —  
Factory or field-installed manually set  
outdoor air dampers shall provide up to  
50 percent outside air. Once set, outdoor  
air dampers shall open to set position  
when indoor fan starts. The damper  
shall close to the full closed position  
when indoor fan shuts down.  
Accessories/Options  
Electric Heaters — Field-installed electric  
heat modules shall be available for  
installation within basic unit. Electric  
heater elements shall be constructed of  
heavy-duty nickel chromium elements  
internally delta connected for 200 volt,  
wye connected for 380-415 volt. Staging  
shall be achieved through the unitary  
control processor (UCP). Each heater  
package shall have automatically reset  
high limit control operating through  
heating element contactors. All heaters  
shall be individually fused from the  
factory, where required. Power  
Discharge Air Sensing — This factory of  
field-installed option provides true  
discharge air sensing in heating models.  
This sensor is a status indicator readable  
through Traceror Tracker.  
Oversized Motors — Factory or field-  
installed oversized motors shall be  
available for high static applications.  
assemblies shall provide single-point  
connection.  
economizer arrives in the shipping  
position and shall be moved to the  
operating position by the installing  
contractor.  
Clogged Filter/Fan Failure Switch — A  
dedicated differential pressure switch is  
available, factory-installed, to achieve  
active fan failure indication and/or  
clogged filter indication. These  
indications will be registered with either  
a zone sensor with status indication  
lights or an Integrated ComfortSystem.  
Roof Curb The roof curb shall be  
designed to mate with the units  
downflow supply and return and provide  
support and a water tight installation  
when installed properly.The roof curb  
design shall allow field-fabricated  
rectangular supply/return ductwork to be  
connected directly to the curb. Curb shall  
be shipped knocked down for field  
assembly and shall include wood nailer  
strips.  
Remote Potentiometer — The minimum  
position setting of the economizer shall  
be adjusted with this accessory.  
Manual Outside Air Damper — Factory  
or field-installed rain hood and screen  
shall provide up to 50 percent outside air.  
RT-PRC016-EN  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mechanical  
Specifications  
High Pressure Cutout — Standard on all  
units.  
Differential Pressure Switches — These  
factory or field-installed sensors allow  
individual fan failure and dirty filter  
indication for microprocessor controlled  
units. The fan failure switch will disable  
all unit functions and “flash” the Service  
LED on the zone sensor.The dirty filter  
switch will light the Service LED on the  
zone sensor and will allow continued  
unit operation.  
Control Options  
Comm-3/4 Trane Communication  
Interface — This factory or field-installed  
option shall be provided to interface  
microprocessor controlled units with the  
Trane Integrated Comfortsystems.  
Hinged Access Doors — Sheet metal  
hinges are available factory-installed on  
the Filter/Evaporator, Supply Fan/Heat,  
and the Compressor/Control Access  
Doors.  
Comm-5 LonTalk Communication  
Interface — This factory or field-installed  
option shall be provided to allow the unit  
to communicate as a Trane Comm-5  
device or directly with generic LonTalk  
Network Building Automation System  
Controls.  
Black Epoxy Coated Condenser Coil —  
The coil provides corrosion protection to  
condenser coils for seacoast application.  
The protection is a factory-applied  
thermoset vinyl coating, bonded to  
normal aluminum fin stock. The uniform  
thickness of the bonded vinyl layer  
exhibits excellent corrosion protection.  
Reference Enthalpy Control — Replaces  
the dry bulb control with a wet bulb  
changeover controller which has a fully  
adjustable set point. Enthalpy control  
offers a higher level of comfort control,  
along with energy savings potential,  
than the standard dry bulb control. This  
is due to the additional wet bulb sensing  
capability.This option shall be available  
for microprocessor controlled units. It  
can be field-installed, or factory-installed  
with the factory-installed economizer.  
Zone Sensor — This field-installed  
control shall be provided to interface  
with the Micro equipped units and shall  
be available in either manual, automatic  
programmable with night setback, with  
system malfunction lights, or remote  
sensor options.  
Thermostats Two stage heating and  
cooling operation or one stage heating  
and cooling shall be available, for field  
installation, in either manual or  
automatic changeover. Automatic  
programmable electronic with night set  
back shall also be available.  
Differential Enthalpy Control — Replaces  
the standard dry bulb control with two  
enthalpy sensors that compare total heat  
content of the indoor air and outdoor air  
to determine the most efficient air  
source. This control option offers the  
highest level of comfort control, plus  
energy efficiency, available. This option  
shall be available for microprocessor  
controlled units. It can be field-installed,  
or factory-installed with the factory-  
installed economizer.  
Low Ambient Cooling — All  
microprocessor units shall have cooling  
capabilities down to 18°C (0°F) as  
standard.  
RT-PRC016-EN  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Literature Order Number  
File Number  
RT-PRC016-EN  
PL-UN-000-RT-PRC016-EN-11-03  
PL-UN-000-RT-PRC016-EN-10-03  
03-03 Webb/Mason 11-03 Electronic Only  
Supersedes  
Trane  
A business of American Standard Companies  
www.trane.com  
Stocking Location  
Trane has a policy of continuous product and product data improvement and reserves the right to change  
design and specifications without notice  
For more information, contact your local district  
office or e-mail us at comfo[email protected]  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tascam DVD Player DV W11R User Manual
Texas Instruments Stereo Amplifier TPA701 User Manual
Toshiba Computer Drive HDTB105XK3AA User Manual
TP Link Network Card T4UH User Manual
TRENDnet Network Router TEW 430APB c1 User Manual
Tripp Lite Power Supply 450 RTI User Manual
Uniden Cordless Telephone Cordless Telephon User Manual
Uniden Cordless Telephone XC800 User Manual
Verbatim MP3 Player VM 205 User Manual
ViewSonic Digital Photo Frame DPG807 User Manual