DIGITAL COLOUR PLAIN PAPER COPIER
OPERATOR'S MANUAL
FOR COPYING FUNCTIONS
FC15/22
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Changes or modification made to this equipment, not expressly approved by
Toshiba TEC or parties authorized by Toshiba TEC could void the user’s
authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Forgery Prevention Function
This copier has a forgery prevention function.
Please ensure that your digital full colour copier is not used for making copies of prohibited
items.
Download from Www.Somanuals.com. All Manuals Search And Download.
PREFACE
Thank you for purchasing the Toshiba Digital Colour Copier FC15/22. This Operator’s Manual describes
the following:
• how to use the digital colour copier
• how to inspect and carry out maintenance on the digital copier
• how to remedy mechanical and copying problems.
Before using the digital colour copier, thoroughly read and understand the Operator’s Manual. To
ensure that clean copies are made at all times and to make sure that the digital colour copier is in
optimum working order, keep this Operator’s Manual in a handy place for future reference.
Ⅵ
To ensure correct and safe use of the Toshiba Digital Colour Copier FC15/22, this Operator’s
Manual describes safety precautions according to the following three levels of warning:
The meanings of these signal words are as follows. Before reading this Operator’s Manual, you
should fully understand the meaning and importance of these signal words.
Warning ------ Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury, or serious damage or fire in the equipment or surrounding
assets.
Caution ------- Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury, partial damage of the equipment or surrounding
assets, or loss of data.
Note------------ Indicates a procedure you should follow to ensure the optimal performance of
the digital colour copier and problem-free copying.
Tip -------------- Describes handy information useful to know when operating the digital colour
copier.
Advice --------- Describes an operation you should follow to maintain the digital colour copier in
good working order.
Warning
This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
1. Do not touch the connector terminal when disconnecting the cables of peripheral equipment.
2. Before opening any covers or removing any units from the copier, discharge the static
electricity from your body by touching a metal part of the copier.
This product is carrying the CE-Mark in accordance with the related European Directives.
Responsible for CE-marking is Toshiba Europe GmbH, Hammfelddamm 8,41460 Neuss,
Gemany. Phone +49-2131-158-01.
COPYRIGHT 1999
TOSHIBA TEC CORPORATION
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PREFACE (Cont.)
Features of the FC15/22
The FC15/22 is a plain paper digital colour copier.
The FC15/22 allows you not only to process and edit these digital image data, but also enables
copies to be sorted and grouped quietly, quickly and easily. The FC15/22 incorporates a large-
size display with a touch panel and menu keys that graphically represent copier functions. As
a result, anybody can make clear-looking copies quickly and easily.
The FC15/22 also has the following convenient features.
● The first copy is output in 10.3 seconds.
● Full-colour copying speed is 15/22 copies (A4) per minute.
● The original developed 4-beam laser optical unit allows for a compact copier.
● The latest image processing technology reproduces high-resolution real colour.
● A fixing system with less oil reduces the amount of oil stuck to the paper which improves the
transparency of the OHP film.
● Comes with the following digital editing functions:
Trimming, masking, negative/positive reversal, full image,image repeat and mirror image.
● Copy sizes from A5 up to A3 are acceptable. Special paper such as thick paper (60~209g/m2),
OHPfilms,labels andA3-widepaper(304.8mmx457.2mm)arealsoacceptableascopysizes.
Options
● By installing the optional reversing automatic document feeder and automatic duplexer,
duplex copies or single-sided copies can be made automatically from two-sided originals.
Duplex copies can also be made automatically from single-sided originals.
● Adding the optional 20-bin staple sorter permits the quick stapling and sorting of copies.
● The optional advance image enhancement mode automatically analyses the original to
optimally reproduce text, illustrations and photographs.
● Installing an optional printer unit allows additional functions such as scanning images by the
copier and printing out data from the PCs.
Ifanoptionalprintercontrollerisinstalled, thiscopiercanbeusedasacolourprinterorscanner
also.
For purchasing the printer controller, please ask your service centre or distributor.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
■
■
■
PREFACE ....................................................................................................................
TABLE OF CONTENTS .............................................................................................
PRECAUTIONS ..........................................................................................................
1
3
5
1. INSTALLATION ..................................................................................................................... 5
2. GENERAL PRECAUTIONS ................................................................................................... 6
1. DESCRIPTION OF THE DIGITAL COPIER ...............................................................
7
1. NAMES OF THE MAIN COMPONENTS ............................................................................ 8
2. DESCRIPTION OF THE OPTIONAL EQUIPMENT ............................................................. 9
3. DESCRIPTION OF THE CONTROL PANEL ...................................................................... 10
4. DESCRIPTION OF THE MESSAGE DISPLAY .................................................................. 13
5. DESCRIPTION OF THE GRAPHIC DISPLAY .................................................................... 15
2. HOW TO MAKE COPIES ........................................................................................ 17
1. PAPER.................................................................................................................................. 18
2. ENERGY-SAVING FUNCTION ........................................................................................... 20
3. TURNING ON THE POWER SWITCH/AUTO JOB START ............................................. 21
4. USING THE REVERSING AUTOMATIC DOCUMENT FEEDER (OPTIONAL) ............... 24
5. COPYING IN THE AUTOMATIC PAPER SELECTION MODE ........................................ 28
6. REDUCTION AND ENLARGEMENT COPYING................................................................ 32
7. COPYING WITH COPY DENSITY SELECTION ................................................................ 36
8. COPYING BY ORIGINAL MODE SELECTION.................................................................. 38
9. COLOUR MODE.................................................................................................................. 40
10. BYPASS COPYING (THICK PAPER/OHP FILM) ............................................................... 41
11. CASSETTE SETTING FOR THICK PAPER/OHP FILM ..................................................... 47
12. INTERRUPT COPYING ....................................................................................................... 49
3. COLOUR EDITING AND ADJUSTMENT .............................................................. 51
1. MONOCOLOUR COPYING ................................................................................................ 52
2. HUE ADJUSTMENT ........................................................................................................... 53
3. SATURATION ..................................................................................................................... 54
4. COLOUR BALANCE (YMCK ADJUSTMENT) .................................................................. 55
5. RGB ADJUSTMENT ........................................................................................................... 56
6. ONE-TOUCH ADJUSTMENT............................................................................................. 57
7. BACKGROUND ADJUSTMENT......................................................................................... 58
8. SHARPNESS ADJUSTMENT............................................................................................. 59
4. USING THE EDITING FUNCTIONS ....................................................................... 61
1. IMAGE SHIFT COPYING.................................................................................................... 62
2. EDGE ERASE COPYING .................................................................................................... 64
3. BOOK CENTRE ERASE ...................................................................................................... 66
4. DUAL-PAGE COPYING ...................................................................................................... 68
5. FULL IMAGE COPYING ..................................................................................................... 70
6. 2 IN 1 MODE COPYING .................................................................................................... 71
7. DUPLEX COPYING ............................................................................................................. 73
1
DUPLEXED COPIES FROM SINGLE-SIDED ORIGINALS ............................................. 73
DUPLEXED COPIES FROM TWO-SIDED ORIGINALS ................................................. 77
SINGLE-SIDED COPIES FROM TWO-SIDED ORIGINALS ........................................... 78
DUPLEXED COPIES FROM BOOK ORIGINALS............................................................ 79
2
3
4
8. X-Y ZOOM .......................................................................................................................... 82
9. TRIMMING/MASKING ........................................................................................................ 83
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS (Cont.)
10. MIRROR IMAGE ................................................................................................................. 87
11. NEGATIVE/POSITIVE REVERSAL ...................................................................................... 88
12. CENTRING........................................................................................................................... 89
13. IMAGE REPEAT .................................................................................................................. 91
5. USING THE SPECIALFUNCTIONS....................................................................... 9
3
1. AUTOMATIC CALIBRATION .............................................................................................. 94
2. SETTING THE DATE AND TIME ....................................................................................... 97
3. WEEKLY TIMER .................................................................................................................. 99
4. MODE MEMORY .............................................................................................................. 101
5. COPYING USING PAPER OF UNIVERSAL SIZES.......................................................... 103
6. ACCESS CODES (ID NUMBERS) .................................................................................... 107
7. TOTAL COUNTER............................................................................................................. 108
8. DEPARTMENT MANAGEMENT ...................................................................................... 109
9. KEY COPY COUNTER...................................................................................................... 117
10. CHANGE OF LANGUAGEONTHEDISPLAYPANEL................................................... 118
11. USER SELECTION (INITIAL SETTINGS)......................................................................... 119
6. USING THE OPTIONAL STAPLE SORTER ............................................................121
1. DESCRIPTION OF THE MAIN COMPONENTS.............................................................. 122
2. NON-SORT COPYING ...................................................................................................... 123
3. SORT OR STAPLE SORT COPYING ............................................................................... 124
4. GROUP COPYING ............................................................................................................ 128
7. WHEN THE GRAPHIC SYMBOLS FLASH .............................................................129
1. ADD PAPER SYMBOL ..................................................................................................... 130
2. REPLACE TONER BAG SYMBOL ................................................................................... 134
3. ADD TONER SYMBOL..................................................................................................... 136
4. CLEAR PAPER SYMBOL.................................................................................................. 138
1
MISFEEDING INSIDE OF THE COPIER........................................................................ 138
MISFEEDING IN THE AUTOMATIC DUPLEXER......................................................... 143
MISFEEDING FROM THE CASSETTES ....................................................................... 145
MISFEEDING IN THE LARGE-CAPACITY FEEDER ..................................................... 146
2
3
4
MISFEEDING IN THE AUTOMATIC DOCUMENT FEEDER ........................................ 147
MISFEEDING IN THE BYPASS GUIDE........................................................................ 148
MISFEEDING IN THE STAPLE SORTER ...................................................................... 149
5
6
5. REPLACING STAPLES ...................................................................................................... 150
6. REMOVING JAMMED STAPLES .................................................................................... 152
7. CALL SERVICE SYMBOL ................................................................................................. 154
8. PERIODIC MAINTENANCE .............................................................................................. 154
■
■
MAINTENANCE ......................................................................................................155
1. DAILY INSPECTION ......................................................................................................... 156
2. SIMPLE TROUBLESHOOTING ........................................................................................ 157
SPECIFICATIONS, ACCESSORIES & OPTIONS ...................................................159
1. FC15/22 SPECIFICATIONS................................................................................................ 160
2. SPECIFICATIONS OF OPTIONS ...................................................................................... 161
3. PACKING LIST .................................................................................................................. 163
4. COPYING FUNCTION COMBINATION MATRIX ........................................................... 164
5. IMAGE QUALITY ADJUSTMENT COMBINATION MATRIX ........................................ 165
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1. INSTALLATION
The FC15/22 should be installed by a qualified service technician.
Note: The packing material should be disposed of properly.
1
To obtain the best possible results, this copier should be used in conjunction with a
dedicated AC power line at the following ratings:
220-240 V, 50/60 Hz, 9 A
2
Notes:
1. The use of other appliances or other equipment on the same line as this copier may adversely
affect performance and copy quality.
2. Be sure to use a 3-conductor, grounded wall outlet.
3. In areas where a 2-pin plug is used, the copier must be grounded for safety.
Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.
After a suitable place has been selected for the installation for the FC15/22, please do
not change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide
proper ventilation as the copier emits a slight amount of ozone.
3
Notes:
1. Recommended environmental range for use is as follows:
• Temperature: 10~30؇C/50~86ЊF
• Humidity: 20~80%RH
2. To insure optimal operation, allow clearances of at least 80cm on the left, 80cm on the right
and 10cm in the rear.
80 cm
80 cm
The copier should be located near a wall outlet which should be easily accessible.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS (Cont.)
2. GENERAL PRECAUTIONS
Handle and use the copier gently and carefully.
ⅷ Do not place anything on the paper cassettes or original feed tray.
ⅷ Never allow the power cable to be trampled on or pinched between hard objects, otherwise
an accident or electrical trouble might occur.
ⅷ Do not allow any metal things such as paper clips to fall into the copier.
1
Be sure to turn OFF the power switch (unless using automatic timer mode):
ⅷ When you leave your office at night.
ⅷ If a power failure occurs.
Caution: When turning OFF the power switch, be sure to do so only after the machine cycling
has come to a complete stop.
2
Be sure to disconnect the power-cord plug:
ⅷ when you do not intend to use the copier for an extended period of time such as during
weekends or the summer vacation.
Be sure to turn OFF the power switch immediately and call for service:
ⅷ If an unusual noise is heard from the copier.
ⅷ If the outside of the copier becomes unusually hot.
ⅷ If any part of this copier is damaged, or if it has been dropped.
ⅷ If the copier has been exposed to rain or liquid.
It is recommended that only supplies made or designated by Toshiba be used for the
FC15/22 in order to optimize copy quality. All supplies should be stored in a cool,
dry area.
Paper of lower quality may contain inherent properties such as excess paper dust and may
lead to premature servicing.
3
DONOTLEANON,APPLYFORCEORPLACEHEAVYOBJECTSONSORTER.PERSONAL
INJURY OR PROPERTY DAMAGE MAY RESULT.
Machine Noise Information
Ordinance 3. GSGV, January 18, 1991: The maximum sound pressure level is equal or less than
70 dB(A) according to EN27779.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DESCRIPTION OF THE DIGITAL COPIER
1.Names of the Main Components . . . . . . . . . . .
2.Description of the Optional Equipment . . . . . .
8
9
3.Description of the Control Panel . . . . . . . . . . . 10
4.Description of the Message Display . . . . . . . . 13
5.Description of the Graphic Display . . . . . . . . . 15
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. NAMES OF THE MAIN COMPONENTS
Original cover
(Optional)
Original scale
Original
glass
Control panel
Copying
Prohibition Label
Exit side cover
(Left side)
Key copy
counter slot
Cassette
(The 3rd and 4th
cassettes are
optional.)
Power
switch
Bypass guide
Feed side cover
Transfer belt unit
Paper size indicator
Fuser unit
Operator's manual pocket
(Back side)
Fuser unit
Left-hand
Toner cartridge
front cover
Right-hand front cover
Explanatory Label
CLASS
LASER KLASSE
APPAREIL LASER DE CLASSE
1
LASER PRODUCT
1
A
1
Electrophotographic unit
Transfer belt unit
Used toner bag Transfer belt unit knob
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. DESCRIPTION OF THE OPTIONAL EQUIPMENT
1
Reversing automatic document feeder
3
Staple sorter
Original feed tray
5
Key copy counter
4
Large-capacity feeder
2
Automatic duplexer
1
2
3
Reversing Automatic Document Feeder
A set of originals can automatically be fed one by one to make copies.
Automatic Duplexer
This reverses the copies in order to make duplex copies.
Staple Sorter
Up to 20 sets of copies can be automatically sorted. There are the following three modes.
• Sort
: The copies can be sorted in the same order as the originals.
: The same pages can be sorted in the same bins.
• Group
• Sort/Staple : Each set can be sorted and stapled respectively.
4
5
Large-Capacity Feeder
You will have an additional paper source which can hold up to 1500 sheets of A4-sized paper
(80 g/m2).
Key Copy Counter
Copies made are recorded (added) according to particular individuals or groups.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. DESCRIPTION OF THE CONTROL PANEL
q
MECHANICAL COUNTER
The total number of
copies (converted into
Lettersize)madeafterthe
installation of the copier
is shown here.
t
ENERGY SAVER key
u
Touch panel
When you are not going
tousethecopierforalong
period of time, press this
key. Thecopierentersthe
energy-saving mode and
all display lamps go out.
Toresumecopying,press
thiskeyagain. Thecopier
becomes ready for
copying after a while.
(See page 20)
The status of the copier,
operationproceduresand
variousinstructionstothe
user are shown in the
pictorials and text.
w
e
TIMER lamp
This lamp lights during
the use of the timer.
i
o
COLOUR SAMPLE SEAL
This seal shows samples
of the monocolour mode.
INFO key
ACCESS key
Usethiskeytodisplaythe
appropriate operation
procedure.
Pressthiskeytoadminister
the users of the copier by
theaccesscode. Pressthis
key again when you finish
making copies so that the
nextpersonmustenterhis/
her own access code to
make the copier available
again. (See page 107)
y
INTERRUPT key
When you want to make
a copy of a different
r
SETTINGS key
original
during
a
The current copy modes
or an editing function list
are shown with the
corresponding icons.
See page 12.
multicopy run, press this
key. During interrupt
copying, copies can be
made only one by one.
To return to the previous
multicopy run, press this
key again.
4
1
2
3
5
6
7
INFO
16
15
10
Download from Www.Somanuals.com. All Manuals Search And Download.
!
FUNCTION CLEAR key
When you press this key,
all the modes you have
selectedwillbeclearedto
the default copy status.
!
COLOUR MODE
SELECTION key
• AUTO COLOUR :
The type of original is
automaticallyrecognized.
Coloured originals are
!
!
!
!
STOP key
Press this key to stop a
multicopy run.
colour-copied
and
monocolour originals are
copied in monocolour.
• FULL COLOUR :
Regardless of colour, all
originals are colour-
copied.
START key
Press this key to start
copying.
• BLACK :
CLEAR key
Use this key to correct the
entered copy quantity.
Regardless of colour, all
originals are copied in
monocolour.
DIGITAL keys
!
CLIP TRAY
Use these keys to enter
thedesiredcopyquantity.
Up to 999 copies can be
set.
Put any paper clips
removed from the
originals here for safe
keeping.
8
9
10
11
14
13
12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. DESCRIPTION OF THE CONTROL PANEL(Cont.)
SETTINGS CONFIRMATION function
● If you press the SETTINGS key
, the screen
on the right will appear.
The icons displayed on the screen are as follows (some icons may not appear on the screen):
MIXED
ORIGINAL SIZES
SADF
SORT
GROUP
STAPLE SORT BACKGROUND
ADJUSTMENT
COLOUR
RGB
ONE TOUCH
MONOCOLOUR
SHARPNESS
HUE
SATURATION
BALANCE
ADJUSTMENT ADJUSTMENT
1➞2
2➞2
2➞1
RIGHT➞RIGHT RIGHT➞LEFT
LEFT➞LEFT LEFT➞RIGHT
LEFT
RIGHT
BOOK
DUAL PAGE
EDGE ERASE BOOK CENTRE
ERASE
2 IN 1
2 IN 1
DUPLEX
XY ZOOM
FULL
IMAGE
SPECIAL SHEET
TRIM
MASK
MIRROR
NEG / POS CENTRING IMAGE REPEAT
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4. DESCRIPTION OF THE MESSAGE DISPLAY
The Message Display panel shows the operation state,error messages and function menus.
ⅷ Eachicondisplayedisshownintheformofatouchkey.Youcanselectthefunctionbytouching
the key lightly with your finger.
ⅷ Turning ON the power switch will show the Basic menu.
The function items shown on the right can be selected directly on the Message Display panel.
2
3
4
5
6
7
8
1
9
17
10
11
16
15
12
13
14
1
2
3
Message
DUAL PAGE (Page 68)
FULL IMAGE (Page 70)
2 IN 1 (Page 71)
2 IN 1 DUPLEX (Page 71)
XY ZOOM (Page 82)
EDITING
The current status of the copier appears here.
Reproduction ratio
The selected reproduction ratio appears here.
BASIC key
TRIMMING/MASKING (Page 83)
MIRROR IMAGE (Page 87)
NEGATIVE/POSITIVE REVERSAL
(Page 88)
There are setting menus of copy forms, duplex
copying, sort and original modes.
UsethiskeytoreturntotheBASICscreen.(See“2.
How to make copies” on page 17.)
CENTRING (Page 89)
IMAGE REPEAT (Page 91)
4
COLOUR key
Use this key to select :
MONOCOLOUR (Page 52)
6
7
Copy Quantity
The number of copies entered with the
digital keys is displayed here.
HUE/SATURATION (Page 53,54)
COLOUR BALANCE (YMCK ADJUSTMENT) (Page 55)
RGB ADJUSTMENT (Page 56)
ONE-TOUCH ADJUSTMENT (Page 57)
BACKGROUND ADJUSTMENT (Page 58)
SHARPNESS (Page 59)
Copy Paper Type
Theiconoftheselectedmodeisdisplayed
whenthickortransparentpaperisselected.
5
EDIT key
Use this key to select :
IMAGE SHIFT (Page 61)
EDGE ERASE (Page 62)
BOOK CENTRE ERASE (Page 66)
SPECIAL SHEET
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. DESCRIPTION OF THE MESSAGE DISPLAY(Cont.)
8
Colour Mode
How to Cancel the Selected Functions
The selected colour mode (AUTO COLOUR, FULL
● Pressingtheselected(shaded)keyonce
COLOUR,BLACKorMONOCOLOUR)isdisplayed
again clears the function you have
here.
selected (excluding some functions).
9
PROGRAM key
● Pressing nothing will also clear the
Use this key to select:
settings to the default mode by the
AUTOMATIC DOCUMENT FEEDER (Page 24)
automatic clear function.
MIXED ORIGINAL SIZES (Page 27)
BYPASS FEED (Page 41)
THICK PAPER (Page 47)
CALIBRATION (Page 94)
DATE/TIME (Page 97)
WEEKLY TIMER (Page 99)
Automatic Function Clear Mode
● IfyoudonotpresstheSTARTkeywithin
about 45 seconds after having set the
desired copy modes, the functions you
MODE MEMORY (Page 101)
have selected are automatically cleared
UNIVERSAL (Page 103)
to the default mode.
TOTAL COUNTER (Page 108)
● While the Department Management
function is being operated, the display
DEPT.MANAGEMENT (Page 109)
CHANGE LANGUAGES (Page 118)
returns to the access code input screen
USER SELECTION (Page 119)
(See page 107).
10
Copy Form key
Use this key to set reproduction, copy size, etc.
11
Duplexed Copy key
Use this key to make 2-sided copies from 2-sided
(or book) or 1-sided originals. You can also make
1-sided copies from 2-sided originals. (Page 73)
12
SORT/STAPLE Setting key
Use this key to select the sort, group and stapling
modes. An optional sorter must be installed to
display this key. (Page 121)
13
Original Mode Selection key
Use this key to select the suitable copy mode for
the originals.
14
AUTO key
Use this key to make the copier automatically
detect the density and background of the original
and determine the optimum copy density.
15
Manual Density Selection key
Press the keys of both sides to change the copy
density.
16
Cassette Switch key
Use this key to switch cassette (including sheet
bypass).
*Pressing the desired cassette on the Message
Display panel will also select the cassette.
17
KEY COPY COUNTER symbol
This symbol flashes when the optional copy
counter is not inserted in the copier.
Insert it to make copies. (Page 117)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5. DESCRIPTION OF THE GRAPHIC DISPLAY
ThegraphicontheMessageDisplaypanelshowsthestatusofthecopier. Whenoneofthegraphic
symbols flashes, take the appropriate action referring to the page shown.
q
!
w
e
r
t
!
!
!
o i u
y
q
w
CHECK ORIGINAL symbol
This symbol flashes when an original is misfed
insidetheautomaticdocumentfeeder.(Page147)
i
o
CLEAR PAPER symbol
This symbol flashes when paper is misfed
in the automatic duplexer. (Page 143)
CLEAR PAPER symbol
This symbol flashes when paper is misfed
on the transfer belt. (Page 138)
BYPASS MISFEED symbol
This symbol flashes when no paper is fed into the
copier in bypass copying. Remove and reset the
sheets on the sheet bypass. (Page 148)
!
!
!
!
REPLACE TONER BAG symbol
This symbol flashes when the toner bag
becomes full of used toner. (Page 134)
e
r
t
ADD TONER symbol
This symbol flashes when the toner supply in the
cartridge runs out. (Page 136)
CLEAR PAPER symbol
This symbol flashes when paper is misfed
in the fuser unit. (Page 138)
CLEAR PAPER symbol
This symbol flashes when paper is misfed on the
paper path inside the copier. (Page 138)
SORTER MISFEED symbol
This symbol flashes when paper is misfed
in the optional staple sorter. (Page 149)
CLEAR PAPER symbol
This symbol flashes when a sheet of paper fed
from the large-capacity feeder is misfed in the
paper feed section. (Page 146)
CALL SERVICE symbol
This symbol flashes when maintenance
by a service technician is necessary.
(Page 154)
y
u
CLEAR PAPER symbol
This symbol flashes when a sheet of paper fed
from the selected cassette is misfed in the paper
feeding section. (Page 145)
STACK symbol
This symbol flashes when sheets of paper copied
on one side are stacked in the duplexer. This
symbol also flashes when sheets of paper are left
in the duplexer. In this case, remove paper from
the duplexer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2. HOW TO MAKE COPIES
1.Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.Energy-Saving Function . . . . . . . . . . . . . . . . . . 20
3.Turning ON the Power Switch/
Auto Job Start . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.Using the Reversing Automatic
Document Feeder (Optional) . . . . . . . . . . . . . . 24
5.Copying in the Automatic Paper
Selection Mode . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.Reduction and Enlargement Copying . . . . . . . 32
7.Copying with Copy Density Selection . . . . . . . 36
8.Copying by Original Mode Selection . . . . . . . . 38
9.Colour Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.Bypass Copying (Thick Paper/OHP Film) . . . . 41
11.Cassette Setting for Thick Paper/OHP Film . . 47
12.Interrupt Copying. . . . . . . . . . . . . . . . . . . . . . . . 49
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. PAPER
Acceptable Paper Types and Sizes
Refer to the list below for the acceptable paper.
Use the recommended paper for optimum copy quality.
Feeder
1st
Cassette
Paper Type
Plain paper
Paper Size
(Standard size)
A3,A4,A4-R,A5-R,B4,B5,B5-R,
FOLIO(210X330mm),
LD(11"X17"),LG(8.5"X14"),
LT(11"X8.5"),LT-R(8.5"X11"),
ST-R(5.5"X8.5"),
Maximum Capacity
600 sheets(80g/m2)
500 sheets(90g/m2)
Remarks
This is not available as a
paper source when the
duplexer is installed.
2nd
Cassette
Plain paper
600 sheets(80g/m2)
500 sheets(90g/m2)
THICK1
(91-105g/m2)
COMP(10•1/8"X14")
400 sheets (105g/m2)
*1
Paper cannot be placed
in the A4-R direction.
OHP film
(Standard size)
A4
100 sheets
3rd
Cassette
Plain paper
(Standard size)
600 sheets(80g/m2)
500 sheets(90g/m2)
A3,A4,A4-R,A5-R,B4,B5,B5-R,
FOLIO(210X330mm),
LD(11"X17"),LG(8.5"X14"),
LT(11"X8.5"),LT-R(8.5"X11"),
ST-R(5.5"X8.5"),
THICK1
(91-105g/m2)
400 sheets (105g/m2)
*1
*1
*1
4th
Cassette
Plain paper
COMP(10•1/8"X14")
600 sheets(80g/m2)
500 sheets(90g/m2)
THICK1
400 sheets (105g/m2)
(91-105g/m2)
Sheet
Bypass
Plain paper
(Standard size)
50 sheets (80g/m2)
40 sheets (90g/m2)
A3,A4,A4-R,A5-R,B4,B5,B5-R,
FOLIO(210X330mm),
A3-wide(12"X18"),
LD(11"X17"),LG(8.5"X14"),
LT(11"X8.5"),LT-R(8.5"X11"),
ST-R(5.5"X8.5"),
THICK1
(91-105g/m2)
30 sheets
20 sheets
THICK2
(106-140g/m2)
COMP(10•1/8"X14")
THICK3
(141-209g/m2)
Labels
(Non-standard size)
(THICK2,THICK3) Length:100-305mm,
Width:148-457mm
*1
OHP film
(Standard size)
A4
20 sheets
Paper cannot be placed
in the A4-R direction.
*1
Large-
Capacity
Feeder
…
Plain paper
(Standard size)
A4
1500sheets(80,90g/m2) Paper cannot be placed
1250sheets(105g/m2) in the A4-R direction.
1
Duplex copying with the optional automatic duplexer is not available.
*
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Paper
To make copies with a fine image, use of the following sheets is recommended.
If you use copy paper other than the recommended types, ask your service technician.
Paper Type
Toshiba Recommendations / Manufacturer
Color Copy (90g/m2) / Neusiedler
Color Copy (100g/m2) / Neusiedler
Color Copy (120g/m2) / Neusiedler
Color Copy (160g/m2) / Neusiedler
Color Copy (200g/m2) / Neusiedler
5165 / Zweckfoem-Avery
Size
Mode
Plain Paper
A3, A4
A3, A4
A3, A4
A3, A4
A3, A4
A4
PLAIN
THICK 1
THICK 2
THICK 3
THICK 3
THICK 2
OHP FILM
Thick Paper
Labels
OHP Film
CG 3700 / 3M
A4 (125µm)
BG 78 / Folex
* Be sure to use only the OHP films specified by Toshiba.
Using other types of OHP films may result in the failure of the copier.
Instructions before use
• Using paper with a special process on the surface, paper printed by another copier, or making
a copy on the paper surface that has already been copied once may cause poor copy quality.
• Do not use creased, folded, wrinkled, curled, slippery or stiff paper which may cause paper jams.
• Keep the copy paper wrapped. Do not expose it to high humidity after taking the copy paper
out of the wrapping paper.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. ENERGY-SAVING FUNCTION
Theenergy-savingfunctionistosavethepowerconsumptionbyloweringthefusertemperature
while the copier is not being used.
There are two levels for this function.
Energy saving
efficiency
Warm-up time
Level 1
Level 2
approx.50% (142W) approx.5 minutes
approx.20% (227W) approx.2min.30sec.
* Power consumption during normal standby
: approx. 284W
● Level 1 is set as the default mode. You can
switch the initial mode depending on user's
environment (see page 119).
Forcibly Switching to Energy-saving Mode
Press the ENERGY SAVER key on the
control panel to forcibly switch to the
energy-saving mode (see page 10).
INFO
Cancelling the Energy-saving Mode
Press the ENERGY SAVER or START key
on the control panel.
The Energy-saving lamp goes off and the copier
starts warming up again (see page 10).
See the table above for the warm-up time.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. TURNING ON THE POWER SWITCH / AUTO JOB START
Turning ON the Power Switch
Turn ON the power switch.
1
● The following message appears.
Wait Warming Up
About 9 minutes later, the message
“READY” appears.
● This message indicates that you can make
2
copies at any time.
● If this message appears:
Wait
If the copier has not been used for a long
Performing Auto Calibration
time, the copier automatically goes into the
adjustment mode and the message on the
right appears before warming up.
It will soon start working.
Do not turn OFF the power. Just wait for
a while.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. TURNING ON THE POWER SWITCH / AUTO JOB START (Cont.)
Auto Job Start
If you set the desired copying modes and press the START key during warm-up, the copier
automatically starts copying when it becomes READY.
Place the original(s) on the original feed
tray or on the glass.
1
When Using the Automatic Document Feeder
● After aligning the edges of the originals, set
them face up on the original feed tray and
align the slides to the edges of the originals.
● See page 24 for the number of the originals
you can set up at a time.
Slides
Note: Remove any paper clips or staples from
originals before placing them on the
original feed tray.
When Placing the Original on the Glass
● Lifting the original cover or the reversing
automaticdocumentfeeder,placetheoriginal
on the glass face down and with its bottom
towardyouandwithitstopleftalignedagainst
the original scale on the left side.
● Close the original cover or the reversing
automatic document feeder slowly after the
original size has been detected.
Set the desired copy modes.
● The automatic paper selection (APS) mode
2
and copying of one original are selected as
the default modes, but the original size is not
automatically detected in the auto job start
mode.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the START key.
3
● Themessage“WaitWarmingUp.AutoStart”
appears. When the copier becomes ready, it
automatically starts copying in the selected
modes.
Tip: You can change the copying modes even
after pressing the START key. To cancel
theAutoJobStartmode,presstheCLEAR
key or the FUNCTION CLEAR key.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. USING THE REVERSING AUTOMATIC DOCUMENT FEEDER (OPTIONAL)
The optional Reversing Automatic Document Feeder automatically feeds and copies sheet
paper originals placed on the feeding tray one at a time. This is called the “continuous feed
mode.” You can also manually feed originals in one sheet at a time. This is called the “single
feed mode.” If you feed in two-sided originals, this document feeder automatically reverses
originals after they have been copied so that their reverse sides can be copied.
PrecautionsWhenFeedingOriginals
Use originals with a paper weight in the range of 60 to 105 g/m2.
1
The number of the originals you can set up at a time differs depending on their size.
60~90g/m2 91~105g/m2
2
A4, A4-R, A5-R
FOLIO
A3
50
35
25
40
25
20
Do not use the following types of originals as they tend to misfeed or become damaged
in the reversing automatic document feeder:
3
(1) Badly wrinkled or folded originals. In
particular, originals
(4) Clipped or stapled originals
whose leading edge
is curled may be
misfed.
(2) Carbon paper
(5) Tornoriginals(includingthosewithholes
in them)
(3) Taped originals
(6) Damp originals (7) OHP film originals
Folded or curled originals should be smoothed out before
being set on the reversing automatic document feeder.
4
5
Do not mix originals of different widths at the same time.
If the surface of the originals is so rough that they cannot
be moved when two of them are pinched between two
fingertips, or if the surface has been processed, these
originals could not be used because the automatic
document feeder may not be able to separate them.
6
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying in the Continuous Feed Mode
Press the PROGRAM key on the display
panel.
1
2
Press the ADF key.
Press the ADF key on the panel to select
continuous feed.
● ADFishighlightedandselectedasthedefault
feed mode.
● The panel returns to the original display.
3
Select the desired copy size, reproduction
ratio,imagedensitylevelandcopyquantity.
● The automatic paper selection mode is
selected as the default mode.
4
5
Placetheoriginalsontheoriginalfeedtray.
● After aligning the edges of the originals, set
them face up on the original feed tray and
align the slides to the edges of the originals.
Slides
● For setting A3 or B4 sized paper, pull out the
Holder
paper holder in the direction of the arrow.
Press the START key.
● The originals are fed starting with the
6
lowermost one.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. USING THE REVERSING AUTOMATIC DOCUMENT FEEDER (OPTIONAL) (Cont.)
Copying in the Single-Feed Mode
Press the PROGRAM key on the display
panel.
1
Press the ADF key.
2
Press the SADF key on the panel to select
single feeding.
● SADF is highlighted and selected.
● Thetouchpanelreturnstotheoriginaldisplay.
3
Select the desired copy size, reproduction
ratio,imagedensitylevelandcopyquantity.
● The automatic paper selection mode is
4
selected as the default mode.
Align the slides on the original feed tray
Slides
to the size of the original.
● Set the slides a little wider than the actual
5
original width.
Insert the original.
● Place the original face up and insert it in
6
straight along the slides.
● When the original starts being pulled in
automatically, let go of the original.
The original is automatically copied.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying in the Mixed Originals Mode
Press the PROGRAM key on the display
panel.
1
Press the MIXED ORIGINAL SIZES key.
2
As explained on the screen on the right
below, place the originals on the original
feed tray.
3
● Mixed originals of A3 and A4 sized paper can
be copied at the same time.
● After aligning the edges of the originals, set
them face up on the original feed tray and
align the slides to the edges of the originals.
● The number of the originals you can load at
a time is 25.
Slides
Press the SET key .
4
Select the Automatic Paper Selection (APS)
modeorAutomaticMagnificationSelection
(AMS) mode. Then select the desired copy
size, reproduction ratio, image density level
and copy quantity as required.
● To make duplexed copies, select the
Automatic Magnification Selection (AMS)
mode.
5
6
Press the START key.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
5. COPYING IN THE AUTOMATIC PAPER SELECTION MODE
When the power switch is turned ON, the Automatic Paper Selection (APS) mode is selected
as the default mode.
In this mode, if you place an original on the document feeder or on the glass, the copier
automatically detects the size of the original, and selects paper of the same size as the original.
This mode is available only for actual-size (100%) copying.
Procedure
Check that the Automatic Paper Selection
mode is selected.
● If APS is not indicated, press the ZOOM
1
ORG.➞A4 key and select APS .
Place the original(s) on the original feed
tray or on the glass.
2
When Using the Reversing Automatic Document Feeder
● After aligning the edges of the originals, set
them face up on the original feed tray and
align the slides to the edges of the originals.
● See page 24 for the number of the originals
you can set up at a time.
● When the START key is pressed, the sensor
detectsthesizeofthefirstoriginal,andselects
the paper size matched to the original.
Note: Remove any paper clips or staples from
the originals before placing them on the
original feed tray.
Slides
28
Download from Www.Somanuals.com. All Manuals Search And Download.
When Placing the Original on the Glass
● Lifting the original cover or the optional
reversing automatic document feeder, place
the original on the glass face down and with
its bottom toward you and with its top left
aligned against the original scale on the left
side.
● The sensor unit immediately detects the size
of the original, and selects the paper size
matched to the original.
● Close the original cover or the reversing
automatic document feeder slowly after the
original size has been detected.
● Sometimes the following message appears:
Change direction of original
Change the direction of the original on the
glass.
Or
Set correct cassette
Install the correct-sized cassette.
Select the image density level.
● The MANUAL COPY DENSITY mode is
selected as the default mode.
● Ifyouwanttoselectthedesiredimagedensity,
3
press the
or
key.
● If the AUTOMATIC COPY DENSITY AUTO is
selected, the optimum image density is
automatically provided according to the
darkness of the original.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
5. COPYING IN THE AUTOMATIC PAPER SELECTION MODE (Cont.)
Key in the desired copy quantity.
● You can key in up to 999.
● There is no need for this when making only
4
one copy.
● When an incorrect quantity is set, press the
CLEAR key and key in the correct number.
● If you press the FUNCTION CLEAR key, all
items that you have set are cleared, and the
copier returns to the default mode and the
Basic menu appears.
Press the START key.
● Copyingstartsandwhentherequirednumber
5
of copies are made, the copier automatically
stops.
● If you do not press the START key within
45 seconds after having set the desired copy
modes, the functions you have selected are
automatically cleared to the default mode.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
When the Automatic Paper Selection is not Available
The copier may not be able to detect the size
of the following types of original in the APS
mode:
● Transparent originals such as OHP film
● Entirely blackish originals or originals with
blackish edges
● Non-standard size originals such as
newspapers and magazines.
Select the copy size referring to the following
steps.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
1
Select the desired paper size.
● Press the cassette of the desired copy size
on the Basic menu.
2
● Or press the ZOOM ORG.➞A4 key on the
Basic menu to display the screen on the right,
then press the key of the desired copy size.
Return to the Basic menu, then select the
image density level and copy quantity as
required.
3
4
Press the START key.
Tip: If there are sheets of paper set on the
sheet bypass, you must press the COPY-
SIZE key corresponding to the sheets.
See page 41.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. REDUCTION AND ENLARGEMENT COPYING
There are three methods available for enlargement and reduction copying.
● Using Automatic Magnification Selection (AMS):
After selecting the AMS mode and the copy size, when you place an original on the glass
or when an original is fed from the reversing automatic document feeder, the copier
automatically detects the size of the original, and calculates the appropriate reproduction
ratio.
● Specifying the original and copy sizes:
When you specify both the original and copy sizes, the copier automatically calculates the
appropriate reproduction ratio.
● Using the ZOOM keys:
The ZOOM keys
DOWN and
UP allow selection of the desired reproduction ratio
from the range of 25% to 400% at increments by 1%.
* See page 82 for X-Y zoom.
Using Automatic Magnification Selection
Press the ZOOM ORG.
A4 KEY.
1
Press the AMS key.
● The AMS key gets highlighted.
2
3
Press the desired COPY-SIZE key.
● TheselectedCOPY-SIZEkeygetshighlighted.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
4
32
Download from Www.Somanuals.com. All Manuals Search And Download.
● The sensor unit immediately detects the size
oftheoriginal, selectsthepapersizematched
totheoriginal,andcalculatesthereproduction
ratio based on the detected original size and
the selected copy size. The reproduction ratio
is then displayed.
● If the following message appears:
Change direction of original
,
change the direction of the original on the
glass.
● If the following message appears:
Use reduction cassette
,
installthecorrect-sizedcassette, andstartthe
procedure all over again.
Select the desired image density level and
copy quantity.
5
6
Press the START key.
● Reduced or enlarged copies of the selected
size will exit.
Tips:
Thecopiermaynotbeabletodetectthefollowing
types of original in the AMS mode:
● Transparent originals such as OHP film
● Entirely blackish originals or originals with
blackish edges
Refer to “Selecting the Original Size and the
Copy Size” on page 34 to make copies of such
originals.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
6. REDUCTION AND ENLARGEMENT COPYING (Cont.)
Selecting the Original Size and the Copy Size
Press the ZOOM ORG.
A4 KEY.
1
Press the ORIGINAL SIZE key of the same
size as the original to be copied.
2
3
Press the desired COPY-SIZE key.
● Thecopiercalculatesthecorrectreproduction
ratio based on the selected original size and
copy size, and displays the reproduction ratio
on the reproduction-ratio display.
(See page 103 for how to use the UNIV key.)
● If the desired size of paper is not in any of
theinstalledcassettes,thefollowingmessage
appears:
Set correct cassette
Install the correct-sized cassette or use the
sheet bypass.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
4
5
6
Select the desired image density level and
copy quantity.
Press the START key.
Tip: If there are sheets of paper set on the
sheet bypass, you must press the COPY-
SIZE key corresponding to the sheets
(see page 41).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Zoom Keys
Press the desired cassette on the display
panel.
1
2
Press the ZOOM ORG.
A4 KEY.
Press the
Up or
Down key to select
the desired reproduction ratio.
3
● For enlargement, use the
UP key. For
reduction, use the
DOWN key.
● Each time you press either ZOOM key, the
reproduction ratio charges by 1%. Holding
down the key changes the reproduction ratio
continuously.
● Pressing the 400% key or the 25% key
causes 400% or 25% to be immediately
displayed.
● Pressing the 100% key returns the copier
to actual-size copying.
Select the desired image density level and
copy quantity if required.
4
5
Press the START key.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
7. COPYING WITH COPY DENSITY SELECTION
There are two modes of adjusting the image density and background level of the copy.
In the manual copy density mode, you can produce lighter or darker copies.
In the automatic copy density mode, the copier automatically detects the density of the original,
andselectstheoptimumimagedensityandbackgroundlevel. Thismodeissuitablefororiginals
containing only text and illustrations. Originals with black areas and halftoned originals should
be copied in the manual copy density mode.
Copying in Manual Density Mode
Press the
or
key to change the
copy density.
● Toproducelightercopies,pressthe
1
2
key.
Each time you press the key, the density-
indicating mark moves one step to the left,
and your copies are produced proportionally
lighter.
● Toproducedarkercopies,pressthe
key.
Each time you press the key, the density-
indicating mark moves one step to the right,
and your copies are produced proportionally
darker.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
Set the desired copy size, reproduction
ratio and copy quantity if required.
3
4
Press the START key.
● Copies are made in the selected copy density
level.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying in Automatic Density Mode
Press the AUTO key.
1
2
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
Set the desired copy size, reproduction
ratio and copy quantity if required.
3
4
Press the START key.
● The copier automatically detects the density
of the original, and makes copies at the
optimumimagedensityandbackgroundlevel.
Tips:
● When copying has been completed, the
FUNCTION CLEAR key flashes.
Press it or press nothing for 45 seconds to
clear the automatic copy density mode to the
default mode (manual copy density).
● In the automatic copy density mode, the
background level is detected during copying,
so the copying speed becomes slower.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
8. COPYING BY ORIGINAL MODE SELECTION
You can select the copy mode (Text/Photo, Text, Printed Image, Photo, Map or Advanced Image)
and produce clear copies matched to the type of original.
* Advance Image Enhancement mode is an optional.
* The advance image enhancement mode requires the optional AI board to be installed.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
1
2
Press the TEXT/PHOTO key on the Basic
menu.
Pressthe TEXT/PHOTO , TEXT , PRINTED
IMAGE , PHOTO , MAP or ADVANCED
IMAGE key.
● The screen on the right is displayed.
3
Select the appropriate mode depending on the
type of original.
Text / Photo : Original with text and photo mixed
together
Text : Original with text only (or text
and line artwork)
Printed Image : Original with printed photos
such as gravure photos of a
magazine
Photo : Original with photos printed on
photographic paper
Map : Original with fine illustrations and text
Advanced Image (Optional) :
The copier automatically recognizes the
contents of the original in each block or
originals in each page and makes copies
in appropriate modes.
This is suitable for copying several types
of originals mixed together.
Note: In the Advance Image Enhancement
mode, the patterns of originals are
recognizedduringcopying,sothecopying
speed becomes slower.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
If necessary, press the
or
key
to adjust the image density.
4
5
6
Select the desired copy size, reproduction
ratio and copy quantity.
Press the START key.
● Copies are made in the selected copy mode.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
9. COLOUR MODE
This function is to switch the colour copy mode and black-and-white copy mode.
Selecting the Colour Mode
Pressthedesiredcolourmodeselectionkey.
● FULL COLOUR : Regardless of colour, all
1
originalsarecolour-copied.
● AUTO COLOUR : The type of original is
automatically recognized.
Highlighted
INFO
Coloured originals are
colour-copied and black-
and-white originals are
copiedinblack-and-white.
● BLACK :
Regardless of colour, all
originals are copied in
black.
Note: Full colour mode is selected as the default
mode.
Seepage119forchangingtheinitialmode.
● The lamp of the selected key is highlighted
and the selected colour mode is displayed in
the top right corner of the display panel.
Tips:
● In the AUTO COLOUR mode, the colours of
originals are recognized during copying, so
the copying speed becomes slower.
● In the AUTO COLOUR mode,if the colour area
is too small or the colours are close to black
or they are too light, colour originals may be
copied in black. In this case, select the FULL
COLOUR mode.
● Yellowishoriginalsororiginalswithacoloured
background may be automatically copied in
colour even though they are black-and-white.
Tobecertaintomakethecopiesinthedesired
mode, select FULL COLOUR or BLACK.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
10. BYPASS COPYING (THICK PAPER/OHP FILM)
Bypass copying is convenient when the size of any paper cassettes installed in the copier is
not the size you require or when you want to use special sizes of paper such as A3-wide
(305X457mm) paper or special types of paper such as thick paper and OHP films(transparency
or sticker labels).
Bypass Copy Mode
● This copier has bypass copy modes corresponding to paper types.
Refer to the table below and select the mode corresponding to the sheets. Otherwise, it may
cause paper jams or lower the image quality.
● The number of sheets that can be set at a time differs depending on paper type.
Setting more than specified number of sheets at a time may cause copier failure or paper jams.
Be sure to set within the specified range.
● The range of acceptable paper sizes is from A3-wide to A5-R.
Bypass Copy Mode
Corresponding Paper Type
Plain paper (64-80g/m2)
Plain paper (81-90g/m2)
Maximum Capacity
approx.50 sheets
approx.40 sheets
approx.30 sheets
approx.20 sheets
approx.30 sheets
PLAIN
305X457mm
OHP FILM
THICK 1
*A3-wide (64-105g/m2)
OHP films
Thick paper (91-105g/m2) (excluding A3-wide)
Thick paper (106-140g/m2)
Thick paper (141-209g/m2)
Thick sticker labels
THICK 2
approx.20 sheets
THICK 3
*A3-wide paper = 304.8mmX457.2mm
41
Download from Www.Somanuals.com. All Manuals Search And Download.
10. BYPASS COPYING (THICK PAPER/OHP FILM) (Cont.)
Procedure
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
1
2
Placethesheetsofcopypaperonthesheet
bypass and align the slides to the paper
size.
● If you put several sheets on the sheet bypass
at a time, fan the paper well before placing
it.
Slides
● Forsettinghorizontallylong-sizedpapersuch
as A3, B4 or A4-R sized paper, pull out the
paper holder.
Press the PROGRAM key to enter the
Program menu, then press the BYPASS
FEED key.
3
42
Download from Www.Somanuals.com. All Manuals Search And Download.
● When paper is not set on the sheet bypass,
the display in step 4 also appears if you select
bypasscopyingbypressingthebypassguide
icon
on the screen on the right.
Select the desired paper type.
● Plain paper is selected as the default mode.
4
Plain Paper
Press the PLAIN key, then the SET key.
A3-wide(305X457mm)
Select the paper thickness among PLAIN ,
THICK1 , THICK2 and THICK3 keys, press
the 305X457mm key, then the SET key.
Select the desired copy size and set the
other copy modes if required.
5
6
Tips:
● If A4-R paper is used, press the A4 key twice.
● If the size of the sheets fed from the sheet
bypassisnotset,theAutomaticMagnification
Selection is cancelled.
Set the copy quantity.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
10. BYPASS COPYING (THICK PAPER/OHP FILM) (Cont.)
Press the START key.
7
Tips:
● If the BYPASS MISFEED symbol flashes, pull
outthepaperandsetitonsheetbypassagain.
● When copying is finished, the lamp of the
FUNCTION CLEAR key lights. Press the
FUNCTIONCLEARkey,orthebypasscopying
mode will automatically return to the default
mode in 45 seconds.
Thick Paper
● Usetherecommendedthickpaperandsticker
labels if possible. Thick paper sold at stores
is also available for this copier, but paper of
some brands may not be suitable to acquire
a clear image. In this case, ask your service
technician.
● It takes about 30 seconds to a few minutes
to switch between "PLAIN" X "A3-wide
(305X457mm)" X "OHP FILM" and "THICK1"X
"THICK2" X "THICK3" for adjustment.
Perform step 1 to 3 on page 42.
1
Check the type of the thick paper and press
the THICK1 , THICK2 or THICK3 key.
2
Tip: For bypass copying mode for thick paper
and sticker labels, see the table on page
41.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the copy size for bypass copying
and set the desired reproduction ratio if
required (see page 32).
3
● Press the COPY-SIZE key corresponding to
the copy paper that is set.
●
If A4-R paper is used, press the A4 key twice.
Tip: If the size of the sheets fed from the sheet
bypassisnotset, AutomaticMagnification
Selection is cancelled.
Set the copy quantity.
Press the START key.
4
5
45
Download from Www.Somanuals.com. All Manuals Search And Download.
10. BYPASS COPYING (THICK PAPER/OHP FILM) (Cont.)
OHP Films
● Use the recommended OHP films (A4 only).
Using other kinds of OHP films may cause
jams and copier failure, and image quality
may be lowered as well and copies cannot
be made in clear colour. If you want to use
the other kinds of OHP films, ask your service
technician.
● Set the OHP films on the sheet bypass
vertically (same as A4 placement).
If you set them horizontally (same as A4-R
placement), the following message will
appear:
Slides
Set transparency film in A4 direction
● If you select the OHP Film mode, the copy
speed becomes slower.
Perform step 1 to 3 on page 42.
1
2
Press the OHP FILM key.
A4 is automatically selected for the copy
size.
3
Set the copy quantity.
Tip: Up to 20 OHP films can be set at a time.
4
If you will make copies of more than 20
films, feed them from the exclusive
cassette for OHP (see page 48).
Press the START key.
5
46
Download from Www.Somanuals.com. All Manuals Search And Download.
11. CASSETTE SETTING FOR THICK PAPER/OHP FILM
Thick paper with a weight of 91~105g/m2 can be fed from the cassette or large-capacity feeder,
and OHP film can be fed from the cassette. This is convenient if copies are often made on
special paper.
Setting the Cassette for Thick Paper (91~105g/m2)
Set the thick paper (91~105g/m2) on the
2nd, 3rd or 4th cassette, or the large-capacity
feeder.
1
● The procedure for changing the paper size
of the cassette for thick paper is the same as
that for normal paper. See page 130.
● Thick paper with a weight of greater than
105g/m2 can be fed only from the sheet
bypass. See page 42.
● Up to 400 sheets (105g/m2) can be set at a
time.
● Duplex copying with the optional automatic
duplexer is not available.
Press the PROGRAM key to enter the
Programmenu,andpressthe THICKPAPER
key.
2
Press the cassette you have set the thick
paper on the display.
3
● The top cassette cannot be set for thick paper.
Use the 2nd, 3rd or 4th cassette, or the large-
capacity feeder.
Press the SET key.
4
47
Download from Www.Somanuals.com. All Manuals Search And Download.
11. CASSETTE SETTING FOR THICK PAPER/OHP FILM (Cont.)
CheckthatTHICK1isshownontheselected
cassette of the display.
5
Setting the Cassette for OHP Film
Pull out the second cassette slowly until
comes to a stop.
● Only the 2nd cassette is available for setting
1
the cassette for OHP films.
Set the OHP films on the casstte.
● Acceptable size is A4 only. Be sure to set
them vertically (same as A4 placement).
● Up to 100 films can be set at a time.
2
Takeoutthesizemarkplateofthecassette
and set that of the OHP film.
● "OHP FILM" is shown in the paper size
3
indicator.
Size mark plate
of OHP film
Paper size indicator
“OHP FILM” is displayed on the second
cassette on the Basic menu.
4
48
Download from Www.Somanuals.com. All Manuals Search And Download.
12. INTERRUPT COPYING
The interrupt copying mode is convenient when you want to make copies of another set of
originals during a multicopy run. Interrupt copying is possible using the cassettes or the bypass.
Press the INTERRUPT
key.
The following message appears:
1
2
Job interrupted job 1 saved
INFO
Replace the original with a new original.
● See page 22 for how to set the original.
Tip: During the interruption, the reversing
automatic document feeder (optional)
and automatic duplexer (optional) are
inoperable.
Selectthedesiredcopysize, imagedensity
level, reproduction ratio,etc. if necessary.
3
4
5
Press the START key.
● Youcanmakemultiplecopiesbypressingthe
START key once for each copy desired.
After interrupt copying is finished, press
the INTERRUPT key again.
● The following message appears:
Ready to resume job 1
Replacethepreviousoriginalandpressthe
START key.
6
● The remaining number of copies of the
previous multicopy run will be made
automatically.
Inte
rrup
t
C
o
p
y
in
g
d
ur
i
n
g
P
r
in
t
in
g
If you press the COPY JOB REQUEST key
while the printer is being used, interrupt
copying becomes available when the
current printing job is completed.
The screen on the right appears during printing.
● If you want to make copies as soon as
printing has been finished,press the
COPY JOB REQUEST key.
● If you want to cancel the copy request, press
the CANCEL REQUEST key
49
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3. COLOUR EDITING AND ADJUSTMENT
1.Monocolour Copying . . . . . . . . . . . . . . . . . . . . . 52
2.Hue Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . 53
3.Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.Colour Balance (YMCK Adjustment) . . . . . . . . 55
5.RGB Adjustment . . . . . . . . . . . . . . . . . . . . . . . . 56
6.One-Touch Adjustment . . . . . . . . . . . . . . . . . . . 57
7.Background Adjustment . . . . . . . . . . . . . . . . . . 58
8.Sharpness Adjustment . . . . . . . . . . . . . . . . . . . 59
51
Download from Www.Somanuals.com. All Manuals Search And Download.
1. MONOCOLOUR COPYING
You can select one colour out of 10 colours of the colour sample seal to make a monocolour
copy.
Procedure
Press the COLOUR key to enter the colour
menu, then press the MONOCOLOUR key.
1
Press the desired copy colour key.
● Press the MAGENTA key for instance.
2
Note: Refer to the colour sample seal above the
touch panel.
Selectthedesiredcopysize, imagedensity
level, copy quantity, etc. if necessary.
3
Press the START key.
4
52
Download from Www.Somanuals.com. All Manuals Search And Download.
2. HUE ADJUSTMENT
This function is available to adjust the hue by changing the hue circle.
Procedure
Press the COLOUR key to enter the colour
menu, then press the HUE/SATURATION
key.
1
Press the HUE key, then the + or – key
to adjust the hue.
● Pressing the + key brings the colour closer
2
to the next clockwise colour while pressing
the – key brings it closer to the next anti-
clockwise colour.
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Hue Adjustment
There are two ways for clearing the setting.
1
Press the + or – key on the HUE column to
move the indicator to 0, then press the SET key.
2
Press the DEFAULT key, then the SET key.
*The saturation setting also becomes the default
mode.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
3. SATURATION
This function allows you to adjust the saturation of copies.
Procedure
Press the COLOUR key to enter the colour
menu, then press the HUE/SATURATION
key.
1
Press the SATURATION key, then the +
or – key to adjust the saturation.
● Pressing the + key increases the brightness
2
while pressing the – key decreases the
brightness.
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Saturation Adjustment
There are two ways for clearing the setting.
1
Press the
+
or
–
key on the SATURATION
column to move the indicator to 0, then press the
SET key.
2
Press the DEFAULT key, then the SET key.
*The hue setting also becomes the default mode.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
4. COLOUR BALANCE (YMCK ADJUSTMENT)
This function allows you to adjust the colour balance of copies by changing the strength of the primary
colours (Yellow (Y), Magenta (M), Cyan (C) and Black (K)).
Procedure
Press the COLOUR key to enter the colour
menu, then press the COLOUR BALANCE
key.
1
Press the + or – key to adjust the colour
balance.
2
● Pressing the + key enhances the tint of the
colour while pressing the – key decreases
the tint of the colour.
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Colour Balance Adjustment
There are two ways for clearing the setting.
1
Press the + or – key on the column you want
to cancel to move the indicator to 0, then press
the SET key.
2
If you want to cancel all the 4 adjustmets, press
the DEFAULT key, then the SET key.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5. RGB ADJUSTMENT
This function allows you to adjust the colour balance by changing the strength of Red (R),
Green (G) and Blue (B).
Procedure
Press the COLOUR key to enter the colour
menu, then press the RGB ADJUSTMENT
key.
1
Press the + or – key to adjust the colour
balance.
2
● Pressing the + key enhances the tint of the
colour while pressing the – key decreases
the the tint of the colour.
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Saturation Adjustment
There are two ways for clearing the setting.
1
Press the + or – key on the column you want
to cancel to move the indicator to 0, then press
the SET key.
2
If you want to cancel all the 3 adjustmets, press
the DEFAULT key, then the SET key.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
6. ONE-TOUCH ADJUSTMENT
You can make the image quality warm, cool, vivid or clear with one touch.
Procedure
Press the COLOUR key to enter the colour
menu, then press the ONE TOUCH
ADJUSTMENT key.
1
Press the desired mode key.
● Press the WARM key for instance.
2
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
3
Press the START key.
4
57
Download from Www.Somanuals.com. All Manuals Search And Download.
7. BACKGROUND ADJUSTMENT
This function allows you to emphasize the background of light colour originals or to avoid copying
the background of dark colour originals or rear side of originals.
This function is available in the black or monocolour mode as well.
* Automatic density mode is not available with this function.
Procedure
Press the COLOUR key to enter the colour
menu, then press the BACKGROUND
ADJUSTMENT key.
1
Press the
LIGHT or DARK
key.
2
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Background Adjustment
There are two ways for clearing the setting.
1
Press the
LIGHT or DARK
key on the
Background column to move the indicator to 0,
then press the SET key.
2
Press the DEFAULT key, then the SET key.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
8. SHARPNESS ADJUSTMENT
This function is available when you want to emphasize the letters and edges of images.
This function is available in the black or monocolour mode as well.
Procedure
Press the COLOUR key to enter the colour
menu, then press the SHARPNESS key.
1
Press the
SOFT or SHARP
key.
● Pressing
SOFT key suppresses the moiré
2
fringes while pressing the SHARP
emphasizes the letters and sharpens the fine
lines.
key
Press the SET key.
3
4
5
Selectthedesiredcopysize, imagedensity
level, the copy quantity, etc. if necessary.
Press the START key.
Cancelling the Sharpness Adjustment
There are two ways for clearing the setting.
1
Press the
SOFT or SHARP
key on the
Sharpnesscolumntomovetheindicatorto0, then
press the SET key.
2
Press the DEFAULT key, then the SET key.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
60
Download from Www.Somanuals.com. All Manuals Search And Download.
4. USING THE EDITING FUNCTIONS
1.Image Shift Copying . . . . . . . . . . . . . . . . . . . . . 62
2.Edge Erase Copying. . . . . . . . . . . . . . . . . . . . . 64
3.Book Centre Erase . . . . . . . . . . . . . . . . . . . . . . 66
4.Dual-page Copying . . . . . . . . . . . . . . . . . . . . . . 68
5.Full Image Copying . . . . . . . . . . . . . . . . . . . . . . 70
6.2 IN 1 Mode Copying . . . . . . . . . . . . . . . . . . . . 71
7.Duplex Copying. . . . . . . . . . . . . . . . . . . . . . . . . 73
1
Duplexed Copies from Single-sided
Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
2
Duplexed Copies from Two-sided
Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3
Single-sided Copies from Two-sided
Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
4
Duplexed Copies from a Book
Originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
8.X-Y Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9.Trimming/Masking . . . . . . . . . . . . . . . . . . . . . . . 83
10.Mirror Image . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
11.Negative/Positive Reversal . . . . . . . . . . . . . . . . 88
12.Centring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
13.Image Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . 91
61
Download from Www.Somanuals.com. All Manuals Search And Download.
1. IMAGE SHIFT COPYING
You can create margins on the copy. You can specify the position of these margins on either
the right or the left side of the copy. You can also create margins on copies of book originals
by just using the DUAL PAGE mode.
Procedure
Press the EDIT key to enter the Edit menu,
then press the IMAGE SHIFT key.
1
Margin on the Left or Right Side
Select on which side the margin is to be
created.
2
● Pressoneofthe LEFTor RIGHTkeystoselect
the type of margin.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
After having adjusted the margin, press
the SET key.
3
● The default margin is 7 mm.
● To adjust the margin:
0mm
30mm
Press the
or
key to select
thedesiredmarginsetting,andpressthe SET
key.
● In duplex copying, margins in the back are
created on the other side of those in the front.
See page 73 for duplex copying.
Margin on the Book Originals
Select on which side the margin is to be
created.
● Press the BOOK key.
● If you select the BOOK margin, use it in
conjunctionwiththeDUPLEXCOPYINGmode
from book originals (page 79) or DUAL PAGE
mode (page 68).
2
3
After having adjusted the margin, press
the SET key.
● The default margin is 14 mm.
● To adjust the margin:
2mm
30mm
Press the
or
key to select
thedesiredmarginsetting,andpressthe SET
key.
Place the original on the glass.
● The book should be centred on the yellow
4
5
6
indicator line with its bottom toward you.
Selectthedesiredcopysize, imagedensity
level,reproductionratioandcopyquantity.
Press the START key.
Tip: Margins can be created also in the bypass
copy mode. To do this, set the paper in the
sheet bypass (see page 42), and press the
desiredCOPY-SIZEkeytoselectthedesired
paper size.
Yellow
indicator line
63
Download from Www.Somanuals.com. All Manuals Search And Download.
2. EDGE ERASE COPYING
If the edges of an original are torn or dirty, they are reproduced as black stains on the copy.
In the edge erase mode, a white border is created along all edges of the copy. The default
edge erase margin is 5 mm, but you can select any margin between 2 and 20 mm.
Original
Edge-erased copy
Procedure
Press the EDIT key to enter the Edit menu.
1
2
Press the EDGE ERASE key.
How to Change the Edge Erase Margin
● The default edge erase margin is 5mm.
● To change the edge erase margin, press the
2mm
20mm
key to select the desired
or
edge erase margin.
● If the setting is OK, press the SET key.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
3
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
4
5
Press the START key.
Tip: Edges can be erased also in the bypass
copy mode. To do this, set the paper in
the sheet bypass (see page 42), and press
the desired COPY-SIZE key to select the
desired paper size.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
3. BOOK CENTRE ERASE
This function allows you to erase the shadow in the centre of a book original.
The default book centre erase margin is 10mm, but you can select any margin between 2 and
50mm.
Centre Erasing
No Centre Erasing
Procedure
Press the EDIT key to enter the Edit menu.
1
Press the Next key to display the panel on
the right.
2
Press the BOOK CENTRE ERASE key.
3
Changing the Erased Margin
●
Thedefaultbookcentreerasemarginis10mm.
● To change the margin to be erased, press
2mm 50mm
the
desired margin.
● If the set value is correct, press the SET key.
key or
key to set the
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the original(s) on the glass.
● The book should be centred on the yellow
4
5
6
indicator line with its bottom toward you.
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
Press the START key.
Yellow
indicator line
67
Download from Www.Somanuals.com. All Manuals Search And Download.
4. DUAL-PAGE COPYING
The facing pages of a book or magazine are copied one at a time onto two separate sheets
of paper at the same time. You need not move the original on the glass.
*The available paper size for this function is A4 only.
Procedure
Press the EDIT key to enter the Edit menu.
1
2
Press the DUAL-PAGE key.
Press the 1 SIDE key for single-sided
copying or the 2 SIDE key for two-sided
copying.
3
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the A4 copy size.
4
Place the original on the glass.
● The book should be centred on the yellow
5
6
indicator line with its bottom toward you.
Select the desired image density level,
copy quantity, etc. as required.
● To combine with the reduction and
enlargement function, set the reproduction
ratio before setting the original.
Yellow
indicator line
Press the START key.
7
69
Download from Www.Somanuals.com. All Manuals Search And Download.
5. FULL IMAGE COPYING
When the image occupies the entire original (to the edge), this function reduces the ratio a
little bit so that the edges of the image will not be missed.
Original
Full Image Copying
Copying Procedure
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the original.
1
Press the EDIT key to enter the Edit menu.
2
3
Press the FULL IMAGE key.
● The image is automatically reduced by a few
percent so that the entire image is copied on
a sheet.
Return to the Basic menu, then set the
desiredcopysize,imagedensitylevel, copy
quantity, etc. if necessary.
4
5
Press the START key.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
6. 2 IN 1 MODE COPYING
When you set A4 sized originals on the original feed tray and select the 2 in 1 function, the
copier automatically feeds in the originals two at a time and causes them to be copied onto
a single sheet of paper.
If you select the 2 in 1 duplex mode, four originals will be copied onto both sides of a single
sheet of paper.
* This copying mode requires the optional reversing automatic document feeder to be installed.
1st page
2nd page
Procedure
Set the originals on the original feed tray.
● Refer to the illustration below for the order
and direction of originals.
1
2
1
2
1
2
Originals
Copy
Press the EDIT key to enter the Edit
menu and press the 2 IN 1 key.
● When making a duplex copy, press the 2 IN
1 DUPLEX key.
Note: The 2 in 1 duplex mode requires the
optional automatic duplexer.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
6. 2 IN 1 MODE COPYING (Cont.)
Enter the number of the originals.
● To have copies arranged in the correct page
3
order in 2 in 1 copying, it is necessary to let
the copier know the number of originals in
one of the following ways:
● When the operator knows the number of
originals:
→ Key in the number of the originals.
● When making the copier count the number
of originals:
→ Press the Original Count key.
The copier starts counting the originals
automatically.Whenitfinishescountingthem,
this message appears:
Put originals in doc. feeder
Then reset the originals in the original feed
tray in the same way as described in step 1.
Press the SET key.
4
5
Set the desired image density level, copy
quantity, etc.
● Maximum copy quantity for the 2 in 1 duplex
copying is as shown below.
80g/m2 : 50 (all sizes)
90g/m2 : 40 (all sizes)
Press the START key.
6
Note: For automatic stapling in the 2 in 1 mode,
the stapling position is the right bottom
corner rather than the normal left upper
corner of the copy, as shown on the right.
If you want to staple on the left upper
corner, change the direction when
copying has been finished and use the
manual stapling mode (see page 127).
Normal stapling position
1
A
2
B
A B
1
2
Stapling position in 2 in 1
(right bottom corner)
72
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DUPLEX COPYING
1
Duplexed Copies from Single-sided Originals
There are three methods of making duplexed copies from single-sided originals:
•
•
•
Using the reversing automatic document feeder (optional) – For duplex-copying from sheet
originals of the specified sizes and weights.
Setting originals on the glass – For duplex copying from originals that cannot be handled
by the reversing automatic document feeder, etc.
Using the dual-page function (See page 68.) – For duplex copying from the facing pages
of a book or two sheet originals (A4 size only) placed on the glass.
Notes: • This copying mode requires the optional automatic duplexer to be installed.
• Duplex copying can be made in the plain paper (64~90g/m2) mode only.
Originals
Duplexed copy
When Using the Reversing Automatic Document Feeder
Press the 1→1 key on the Basic menu.
1
Press the 1→2 key to select the function
of single-sided originals to double-sided
copies.
2
73
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DUPLEXED COPYING (Cont.)
Press the EVEN or ODD key according
to the number of originals.
When you do not know the number of originals,
set them on the reversing automatic document
feeder and press the Original Count key. The
number of originals will be automatically
counted. When the copier has finished counting
the originals, press the SET key.
3
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
4
● The maximum number of copies is as
shown below.
80g/m2 : 50 (all sizes)
90g/m2 : 40 (all sizes)
Place the originals.
● See page 22 for how to set the originals.
5
Note: Remove any paper clips or staples from
originals before placing them on the
original feed tray.
● When originals are placed to be fed from
the top (or bottom) as shown on the right,
invert the odd-numbered and even-
numbered originals relative to each other
as shown before setting them.
Press the START key.
6
74
Download from Www.Somanuals.com. All Manuals Search And Download.
When Placing the Original on the Glass
Press the 1→1 key on the Basic menu.
1
2
Pressthe 1→2 keytoselectthefunction
of single-sided originals to double-sided
copies.
Press the EVEN or ODD key according
to the number of originals.
3
4
Tip: The original counting function is not
available when the originals are placed
on the glass.
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
● The maximum number of copies is as
shown below.
80g/m2 : 50 (all sizes)
90g/m2 : 40 (all sizes)
75
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DUPLEX COPYING (Cont.)
Place the last page of the originals (first
side).
5
● Lifting the original cover or the reversing
automaticdocumentfeeder,placetheoriginal
on the glass face down and with its bottom
towardyouandwithitstopleftalignedagainst
the original scale on the left side.
● Copying with the last page first causes the
copies made to be arranged in the correct
page order.
● Close the original cover or the reversing
automatic document feeder slowly.
Press the START key.
6
Place the next original (second side).
Vertical placement
● When the first-side original was placed
vertically, the second-side original should be
placed in the same direction.
7
(First side)
(Second side)
● When the first-side original was placed
horizontally, the second-side original should
be placed horizontally but in the opposite
direction.
Horizontal placement
Press the START key.
● The same operation is available if you press
the START key after having pressed the YES
key.
8
Repeat step 5 to 8 until all the originals are
copied.
(First side)
(Second side)
9
Press the FINISHED key after all the
originals have finished being copied.
10
76
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Duplexed Copies from Two-sided Originals
Notes: • This copying mode requires the optional automatic duplexer to be installed.
Notes: • Duplex copying can be made in the plain paper (64~90g/m2) mode only.
Original
Duplexed copy
Press the 1→1 key on the Basic menu.
1
Press the 2→2 key.
2
3
Select the desired copy size, reproduction
ratio, image density level, copy quantity,
etc. if necessary.
● The maximum number of copies is as
shown below.
80g/m2 : 50 (all sizes)
90g/m2 : 40 (all sizes)
When Using the Reversing Automatic Document Feeder
Place the originals.
● See page 22 for how to set the originals.
4
Press the START key.
●
Thecopierfeedsoneoftheoriginalsandcopies
the first side of the original onto a sheet.
The original and the sheet are then turned over
automaticallyandthesecondsideoftheoriginal
is copied onto the other side of the sheet.
5
When Placing the Original on the Glass
Perform step 5 to 10 on page 76.
4
77
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DUPLEX COPYING (Cont.)
3
Single-sided Copies from Two-sided Originals
Original
Copy
Copy
Press the 1→1 key on the Basic menu.
1
Press the 2→1 key.
2
3
Select the desired copy size, reproduction
ratio, image density level, copy quantity,
etc. if necessary.
● The maximum number of copies is as shown
below.
080g/m2 : 50 (all sizes)
090g/m2 : 40 (all sizes)
When Using the Reversing Automatic Document Feeder
Place the originals.
● See page 22 for how to set the originals.
4
Press the START key.
● Single-sidedcopiesareoutputfromthecopier.
5
When Placing the Original on the Glass
Perform step 5 to 10 on page 76.
4
78
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Duplexed Copies from Book Originals
The copies made will be arranged in the same page order as the book.
Notes: • This copying mode requires the optional automatic duplexer to be installed.
Notes: • Duplex copying can be made in the plain paper (64~90g/m2) mode only.
12
15
12
13
15
79
Download from Www.Somanuals.com. All Manuals Search And Download.
7. DUPLEX COPYING (Cont.)
Press the 1→1 key on the Basic menu.
1
Press the BOOK→2 key.
2
Select the start and end page.
● Press the desired key.
3
→
● RIGHT RIGHT Copying is started from a
right page of the book and it
ends on a right page.
→
● RIGHT LEFT Copying is started from a
right page of the book and it
ends on a left page.
→
● LEFT LEFT
Copying is started from a left
page of the book and it ends
on a left page.
→
● LEFT RIGHT Copying is started from a left
page of the book and it ends
on a right page.
Select the copy size.
● Press the A4 COPY-SIZE key.
4
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Select IMAGE SHIFT if necessary.
● See page 62.
5
6
Select the desired image density level,
reproduction ratio, copy quantity, etc. if
necessary.
● The maximum number of copies is as
shown below.
80g/m2 : 50 (all sizes)
90g/m2 : 40 (all sizes)
PlacetheoriginalandpresstheSTARTkey.
● The book should be centred on the yellow
indicator line with its bottom toward you.
● Copying with the last page first causes the
copies made to be arranged in the correct
page order.
7
8
Set the next original.
● Turn over the leaf of the book and set it in
Yellow
indicator line
the same way as previously.
Press the START key.
● Pressing the YES key on the display on the
9
right also continues copying.
Repeatsteps8and9untilyoufinishcopying
the book.
10
Press the FINISHED key after all the
originals have finished being copied.
Press the COPY FINAL PAGE key if the
last original has only one page.
11
81
Download from Www.Somanuals.com. All Manuals Search And Download.
8. X-Y ZOOM
This function allows you to make copies of originals with the reproduction ratio of the X and
Y directions changed.
When the Y zoom ratio
is changed (200%)
When the X zoom ratio
is changed (200%)
100%
200%
100%
200%
Procedure
Press the EDIT key to enter the Editing
menu, then press the Next key.
1
2
Press the XY ZOOM key.
Specify the X and Y reproduction ratios.
● Press the 25%< or >400% key on the display
to select the X reproduction ratio, and press
the upper SET key.
● Select the Y reproduction ratio in the same
way.
3
Press the lower SET key.
4
5
6
Select the desired copy size, image density
level, copy quantity, etc. if necessary.
Place the original(s) on the original feed
tray or on the glass and press the START
key.
● See page 22 for how to set the originals.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
9. TRIMMING/MASKING
This function allows you to trim or mask copies.
You can trim originals (extracting inside area only) by selecting the trimming mode, and you
can mask originals (hiding inside area) by selecting the masking mode. You can specify areas
by placing originals on the glass.
* You can specify only one rectangular place on a single original.
* Only the standard size originals are available for this mode.
Original
Trimmed copy
Masked copy
83
Download from Www.Somanuals.com. All Manuals Search And Download.
9. TRIMMING/MASKING (Cont.)
Specifying an area
X2
Place the original face up on the glass with
its bottom edge towards you and its top
leftalignedagainstthetopleftoftheglass.
Align the original with the original scale
on the left.
X1
Rear scale
1
Original scale
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the original scale and the rear scale,
specifythevaluesdefiningthedesiredarea
as follows:
● X1 • • Distance from the original scale to the
left edge of the specified area
● X2 • • Distance from the original scale to the
right edge of the specified area
2
● Y1 • • Distance from the rear scale to the
upper edge of the specified area
● Y2 • • Distance from the rear scale to the
lower edge of the specified area
Specify the area of the original.
(To display the screen on the right, follow steps
1-3 in the "Procedure" below.)
● Key in the value X1 using the digital keys and
press the upper SET key. If you key in a
wrong value, press the RESET key.
● Values X2, Y1 and Y2 require the same
procedure as X1.
3
4
Press the lower SET key.
Procedure
Press the EDIT key to enter the Editing
menu, and then press the Next key.
1
2
Press the EDITING key.
Press the TRIM or MASK key.
3
4
Place the original face up on the glass with
its bottom edge towards you and its top
leftalignedagainstthetopleftoftheglass.
Tip: Only the standard size originals are
available for this mode.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
9. TRIMMING/MASKING (Cont.)
Following the method of specifying areas
on page 84, key in the size of the area to
be trimmed or masked with the digital
keys, then press the SET key.
5
Place the original on the glass face down
with its bottom toward you and with its
top left aligned against the original scale
on the left side.
6
Selectthedesiredcopysize, imagedensity
level, copy quantity, etc. if necessary.
7
Tips:
● If the setting of original size and copy size
is not appropriate, the image may not be
copied completely.
● In bypass copying, the copy size must be
specified.
Press the START key.
Trimmedormaskedcopiesexitfromthe copier.
8
86
Download from Www.Somanuals.com. All Manuals Search And Download.
10. MIRROR IMAGE
This function allows you to make mirror-imaged copies of the entire original.
Example of mirror image
Procedure
Press the EDIT key to enter the Editing
menu, and then press the Next key.
1
Press the EDITING key.
2
Press the MIRROR key.
3
4
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
Place the original(s) on the original feed
tray or on the glass and press the START
key.
● See page 22 for how to set the originals.
5
87
Download from Www.Somanuals.com. All Manuals Search And Download.
11. NEGATIVE/POSITIVE REVERSAL
In the full colour mode, this function allows you to reverse both hue and shading of the entire
original when making copies. In the black mode or monocolour mode, only the shading of
the entire original is reversed.
Copy
Original
Procedure
Press the EDIT key to enter the Editing
menu, and press the Next key.
1
2
Press the EDITING key.
Press the NEG/POS key.
3
4
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. if necessary.
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the originals.
5
6
Press the START key.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
12. CENTRING
This function allows you to trim all of or a part of the original and print it out in the centre
of a copy sheet.
* This mode is available only for the standard size originals.
Procedure
Press the EDIT key to enter the Edit menu,
then press the Next key.
1
Press the CENTRING key.
2
Press the ALL or PART key to select the
area for centring.
3
89
Download from Www.Somanuals.com. All Manuals Search And Download.
12. CENTRING (Cont.)
When Centring the Entire Image of an Original
Place the original on the glass face down
with its bottom toward you and with its
top left aligned against the original scale
on the left side.
4
Press the BASIC key to return to the Basic
menu, then select the desired copy size,
image density level, copy quantity, etc. if
necessary.
5
Tip: If the setting of original size and copy size
is not appropriate, the image may not be
copied completely.
Press the START key.
6
When Centring a Part of an Original
Place the original on the glass face up with
its bottom toward you and with its top left
aligned against the original scale on the
left side.
4
Followingthe"Specifyinganarea"onpage
84, key in the size of the area to be centred
with the digital keys, then press the SET
key.
5
Place the original on the glass face down
and with its bottom toward you and with
its top left aligned against the original
scale on the left side.
6
Selectthedesiredcopysize, imagedensity
level, copy quantity, etc. if necessary.
7
Tip: If the setting of original size and copy size
is not appropriate, the image may not be
copied completely.
Press the START key.
8
90
Download from Www.Somanuals.com. All Manuals Search And Download.
13. IMAGE REPEAT
This function allows you to repeat the entire original or a part of the area of the original on
the copy.
* This mode is available only for the standard size originals.
Example of mirror image
Standard size
The non-standard size original
can be copied if it is placed on
the standard size original and its
area is specified.
Non-standard size
Procedure
Press the EDIT key to enter the Edit menu,
and then press the Next key.
● The display on the right appears.
1
Press the IMAGE REPEAT key.
2
91
Download from Www.Somanuals.com. All Manuals Search And Download.
13. IMAGE REPEAT (Cont.)
Place the original on the glass face up with
its bottom toward you and with its top left
aligned against the original scale on the
left side.
3
Followingthe“SpecifyinganArea”onpage
84, key in the values of the area to be
repeated (X1, X2, Y1 and Y2) with the
digital keys and press the lower SET key.
● If the entire original will be repeated:
X1=0(mm), Y1=0(mm)
4
X2, Y2=arbitrary
Place the original on the glass face down
with its bottom toward you and with its
top left aligned against the original scale
on the left side.
5
Set the repeat number.
● To change the repeat number:
6
Press the
2 or 8 key to select the desired
repeat number, and press the SET key.
Tip: If the repeat number is not set, the copier
automatically repeats the original once.
Only the length direction is available for
repeat copying, and the original can be
repeated up to 8 times.
Selectthedesiredcopysize, imagedensity
level, copy quantity, etc. if necessary.
7
8
Press the START key.
Tip: If the setting of the paper size or the
repeatnumberisnotmadeappropriately,
the image may not be copied completely.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
5. USING THE SPECIAL FUNCTIONS
1.Automatic Calibration . . . . . . . . . . . . . . . . . . . . 94
2.Setting the Date and Time . . . . . . . . . . . . . . . . 97
3.Weekly Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 99
4.Mode Memory . . . . . . . . . . . . . . . . . . . . . . . . . 101
5.Copying Using Paper of Universal Sizes . . . 103
6.Access Codes (ID Numbers) . . . . . . . . . . . . . 107
7.Total Counter . . . . . . . . . . . . . . . . . . . . . . . . . 108
8.Department Management . . . . . . . . . . . . . . . . 109
9.Key Copy Counter . . . . . . . . . . . . . . . . . . . . . 117
10.Change of Language on the Display Panel . 118
11.User Selection (Initial Settings) . . . . . . . . . . . 119
93
Download from Www.Somanuals.com. All Manuals Search And Download.
1. AUTOMATIC CALIBRATION
This function allows the copier to automatically calibrate the colour gradation when the colour
cannot be adjusted well because the shading or the hue of the image has deviated.
• Set the A3-sized paper in the cassette before starting the calibration.
• Be sure to use the paper recommended by Toshiba. If any other paper is used, the calibration
may not be performed properly.
• If the colour often deviates, call your service technician.
Press the PROGRAM key to enter the
Programme menu.
1
2
Press the Next key, then press the
CALIBRATION key.
Enter the password (4 digits) of your
administrator (key operator), then press
the SET key.
3
Tip: If you do not need the user control by the
password of the administrator, tell your
service technician.
Press the CALIBRATION key.
● The following message appears:
4
WAIT
Wait for a few seconds.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the TEST PRINT key to print out the
chart for calibration.
5
6
Press the CALIBRATION key after the
chart has been output.
When the display on the right appears, set
the chart face down on the glass and with
its bottom toward you and its top left
aligned against the original scale on the
left side, in order that the black line comes
to the left side.
7
8
Press the START key to start the first
calibration.
● If the chart is not properly set, the following
message appears:
Set chart correctly
Repeat the calibration in step 6.
Notes:
● If the glass is dirty or any foreign objects are
stuck to the glass, calibration may not be
operated properly. Keep the glass clean.
● Interrupt copying is not available during
calibration.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
1. AUTOMATIC CALIBRATION Cont.
When the message “Scanning and
calibrating” disappears, press the TEST
PRINT key to print out the second test
chart.
9
Press the CALIBRATION key, then set the
printed out chart on the glass in the same
way as the first calibration.
10
Press the START key to start the second
calibration.
11
12
When the message “Scanning and
calibrating” goes out, all the operation is
completed.
Tip: If you want to return the image quality
level to the default setting after the
calibration, press the DEFAULT key in
step 4.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SETTING THE DATE AND TIME
With the digital keys, dates and times of the copier‘s internal clock can easily be set consistent
with the current date and time.
Press the PROGRAM key to enter the
Programme menu. Press the Next key
and then the DATE/TIME key.
1
Key in the last two numbers of the year
and press
Example: 1999 → 9 + 9 +
.
2
3
2003 → 0 + 3 +
Key in the month (1~12) and press
Example: April → 0 + 4 +
.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
2. SETTING THE DATE AND TIME Cont.
Key in the date (1~31) and press
.
Example: 1st, April → 0 + 1 +
4
5
6
Key in the number corresponding to the
day of the week (1: Sun., 2: Mon. ~7: Sat.)
and press
.
Example: Thu. → 5 +
Number
Day
1
2
3
4
5
6
7
Sun. Mon. Tue. Wed. Thu. Fri. Sat.
Key in the hour (0~23) and press
Example: 10 : 30 a.m. → 1 + 0 +
● Time is displayed in the 24-hour system.
.
Key in the minute (0~59).
Example: 10 : 30 a.m. → 3 + 0
7
8
Check that all the settings are correct.
● If you have noticed an error, first press the
key and then enter the correct number.
Press the SET key.
● The date/time setting screen is cleared.
9
98
Download from Www.Somanuals.com. All Manuals Search And Download.
3. WEEKLY TIMER
The weekly timer, which is incorporated in the copier, is a feature for turning ON and OFF the
copier automatically at the desired times specified. If you set the timer for the start time in
the morning and the end time in the evening of your office, the copier will automatically turn
itself ON and OFF at the specified times to meet the schedule of your office.
* To allow the weekly timer to work properly, the power switch should be always left ON.
Setting the Weekly Timer
Press the PROGRAM key to enter the
Programme menu. Press the Next key and
then the WEEKLY TIMER key.
1
Check the settings. If they are OK, press
the SET key. To change the settings, press
the CHANGE key.
2
Set the ON/OFF times for each day of the
week.
3
● Switch the day of the week by using the
Sun and Sat
● Set the ON/OFF times by using the digital
keys.
keys.
● If the settings for each day of the week are
OK, press the lower SET key.
● For holidays for which the copier should not
be turned on, set the time as follows:
ON : 00:00
OFF : 00:00
99
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
3. WEEKLY TIMER Cont.
Cancelling Operation of the Weekly Timer
You can cancel operation of the weekly timer so that the copier can be turned ON and OFF
as normal by the power switch.
Press the PROGRAM key to enter the
Programme menu and press the Next key.
● The menu on the right appears.
1
Check that the WEEKLY TIMER key is
shaded. Then press the WEEKLY TIMER
key to return the display to normal. This
turns the weekly timer OFF.
2
Tip: Weekly timer ON/OFF settings are held
in the memory unless they are changed.
Thestoredsettingscaneasilyberestored
when the operation of the weekly timer
is resumed.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
4. MODE MEMORY
You can store and recall a combination of frequently used copy modes at any time you like.
In addition to reproduction ratios, you can also store image density levels and copy quantities,
colour adjustment modes, editing modes and duplex copying modes. You can register up to
four combinations.
Storing a New Combination of Copy Modes
Set the desired copy modes.
Example 1:
1
Reproduction ratio .... 85%
Copy quantity ............ 10
Image density ............ Full colour
Copy size .................... A4-R
Example 2:
Colour balance .......... Y(Yellow)+1, M(Magenta)+2
C(Cyan)-1, K(Black)0
Copy size .................... A4-R
Reproduction ratio .... 90%
● You can check that each mode is correctly
set by pressing the SETTINGS key.
Press the PROGRAM key to enter the
Programme menu, and then press
the MODE MEMORY key.
2
Press the MEMORY key.
3
101
Download from Www.Somanuals.com. All Manuals Search And Download.
4. MODE MEMORY (Cont.)
Press the MEMORY1 (or, MEMORY2 , ME
MORY3 , MEMORY4 ) key.
● The combination of copy modes is stored in
mode memory 1 (or, 2, 3, 4)
● Stored combinations of copy modes remain
until new ones are entered. They are not
erased even when the power switch is turned
OFF.
4
Recalling a Stored Combination of Copy Modes
Press the PROGRAM key to enter the
Programme menu, and then press
the MODE MEMORY key.
1
Press the RECALL key.
2
Press the key for the combination of copy
modes you want to recall.
3
4
PresstheSTARTkey.Theoriginaliscopied
in the combination of modes you have
recalled.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
5. COPYING USING PAPER OF UNIVERSAL SIZES
If you set the paper of non-European sizes such
as US standard sizes (Ledger~Statement) in the
cassette for “UNIVERSAL” size, the copier
automatically calculates the reproduction ratio by
the Automatic Magnification Selection mode. And
the reproduction ratio of the originals within the
dimensions shown on the right can automatically
be selected for the standard size by keying in the
paper size.
Original
150~434mm
(5.9"~17.0")
Making US Standard Size Copies
Press the PROGRAM key to enter the
Programme menu.
1
Press the UNIVERSAL key.
2
Press the STANDARD key.
3
Press the desired size key for UNIVERSAL
size.
4
103
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
5. COPYING USING PAPER OF UNIVERSAL SIZES Cont.
To change to a US standard size, reset the
size mark plate so that the UNIVERSAL
mark appears and set the corresponding
size of paper (see page 133).
5
Size mark plate
of UNIVERSAL
Paper size indicator
Press the BASIC key to return to the Basic
menu, then make sure that the “UNIV” is
shown on the paper size indicator of the
corresponding cassette.
6
7
8
Press the ZOOM ORG. → LT key to display
the original size selection screen.
Press the UNIV key of the ORIGINAL on
the screen to make copies of UNIVERSAL
size of originals.
Press the UNIV key of COPY on the screen
if you make copies on the UNIVERSAL size
paper.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
After you have set the originals, select the
copy quantity, etc. if necessary, and press
the START key.
9
Tip: FOLIO is the default size of the UNIVERSAL
size.
Making Copies of Non-Standard Originals
Press the PROGRAM key to enter the
Programme menu.
1
2
Press the UNIVERSAL key.
Press the NON STANDARD key.
3
Key in the dimensions (length, width) of
the original set for the UNIVERSAL size,
then press the upper SET key.
4
5
Ifthekeyed-indimensionsarecorrect,press
the lower SET key.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
5. COPYING USING PAPER OF UNIVERSAL SIZES Cont.
Press the BASIC key to enter the Basic
menu, then press the ZOOM ORG. → A4
key.
6
Press the UNIV key of the ORIGINAL on
the screen.
7
8
After you have set the originals, select the
copy quantity, etc. if necessary, and press
the START key.
Notes:
● Non-standard size paper cannot be set.
● Only one size can be set for the UNIVERSAL
size. You cannot set Standard size and Non-
standard size at a time.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
6. ACCESS CODES (ID NUMBERS)
If the copier is set up so that access codes can be used, you can make copies only after entering
the access code. When making copies using access codes, the copy quantity is stored for each
access code used.
See page 114 for how to register, change, or clear the access code.
If the Department Management function
is activated, the screen on the right is
displayedwhenthepowerswitchisturned
ON or the automatic function clear mode
(page 14) is operated.
1
Key in a registered access code (4 digits)
to make the copier available.
2
Notes:
● Available 4-digit numbers are between 0001
and 9999.
● If the message “Enter job access code” still
appears and the screen does not change, the
keyed-in access code may be wrong. Key in
the correct number.
● When you are using the Department
management function, press the ACCESS
key on the control panel after you
have finished using the copier.
The display changes to the access code input
screen, and Department Management
function is continuously available.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
7. TOTAL COUNTER
This function displays the total number of copies or number of prints.
Press the PROGRAM key to enter the
Programme menu and press the Next key.
1
Press the TOTAL COUNTER key.
2
● The total number of copies or prints of the
copier is displayed classified by the color
mode.
Tip: The total counter is an add-up counter.
You cannot clear the number of the
counter.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
8. DEPARTMENT MANAGEMENT
This function allows you to administer the copy quantity of each department by setting an access
code for each department. Up to 120 codes can be set.
* This function requires keying in the password of the key operator.
Press the PROGRAM key to enter the
Programme menu, and press the Next key
then the DEPT.MANAGEMENT key.
1
Enter the password of the administrator
(key operator).
2
● Thedepartmentmanagementscreenappears.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
8. DEPARTMENT MANAGEMENT Cont.
ID Counter
Thisfunctiondisplaysthenumberofcopiesoutputforeachdepartment(oraccesscode)classified
according to colousr mode.
Press the ID COUNTER key in the
Department Management menu.
1
If you want to check the counters of all
access codes, press the ALL key.
● The total copy quantity of each access code
2
is displayed.
Ifyouwanttocheckthecounterofacertain
department, enteritsaccesscode(4digits)
and press the SET key.
● The total copy quantity of the corresponding
3
access code is displayed in the frame.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
● 4 access codes can be displayed at a time.
Press the NEXT or PREV key to switch the
screen for other access codes.
● Accesscodesaredisplayedinnumericalorder
(up to 120 codes).
111
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
8. DEPARTMENT MANAGEMENT Cont.
Clearing Counters
This function clears a certain department (access code) or all departments to “0”.
Press the CLEAR COUNTER key in the
Department Management menu.
1
If you want to clear the counters of all the
access codes, press the ALL key.
2
If you want to clear the counter of a certain
department, enteritsaccesscode(4digits)
and press the SET key.
3
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the YES key.
● The counter is cleared and the number
4
becomes “0”.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
8. DEPARTMENT MANAGEMENT Cont.
Registration/Change/Deletion of Access Codes
This function registers, changes and deletes the access codes.
Registering a new department
Press the ID REGISTER/CHANGE key in
the Department Management menu.
1
Press the REGISTRATION key.
2
Using the digital keys, enter the access
code (4 digits) you want to register both
for NEW ACCESS CODE and for CONFIRM
ACCESS CODE .
3
Press the SET key.
4
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the access code of a certain department
Press the ID REGISTER/CHANGE key in
the Department Management menu.
1
Press the CHANGE key.
2
3
Using the digital keys, enter the access
code (4 digits) you want to change, then
press the SET key.
Using the digital keys, enter the access
code (4 digits) you want to register both
for NEW ACCESS CODE and for CONFIRM
ACCESS CODE .
4
5
Press the SET key.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
8. DEPARTMENT MANAGEMENT Cont.
Deleting a department from the department management
Press the ID REGISTER/CHANGE key in
the Department Management menu.
1
Press the DELETE key.
2
Using the digital keys, enter the access
code (4 digits) you want to delete, then
press the SET key.
3
Press the YES key.
4
116
Download from Www.Somanuals.com. All Manuals Search And Download.
9. KEY COPY COUNTER
When the copier is set up so that key copy counters can be used, you can make copies only
by inserting your key copy counter, and the copies made are recorded (added) in the key copy
counter. You can use any number of key copy counters.
Note: For details on how to use a key copy counter, consult a service technician.
Procedure
The following message appears:
Set key copy counter
1
Insert the key copy counter.
● Hold the counter so that the surface with an
2
arrow faces upward with the arrow pointed
toward the copier. Then insert it slowly until
it comes to a stop.
The following message appears:
READY
3
● Make copies as you would normally do.
When you have finished making copies,
1 2 3 4 5 6
remove your key copy counter.
4
117
Download from Www.Somanuals.com. All Manuals Search And Download.
10. CHANGE OF LANGUAGE ON THE DISPLAY PANEL
You can change the language on the display panel.
Press the PROGRAM key to enter the
Programme menu, press the Next key twice
to display the panel on the right, then press
the CHANGE LANGUAGES key.
1
Press one of the other languages.
2
118
Download from Www.Somanuals.com. All Manuals Search And Download.
11. USER SELECTION (INITIAL SETTINGS)
This function allows you to change the initial setting (default setting) of each mode displayed
whenthepoweristurnedON,whentheEnergy-Savingmodeiscancelled,orwhentheFUNCTION
CLEAR key is pressed.
Press the PROGRAM key to enter the
Programme menu, then press the Next
key.
1
Press the USER SELECTION key.
2
Press the desired key for which you want
to change the initial setting.
● You can switch the screen by pressing the
3
Next or Pre key.
Press the SET key.
4
119
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
120
Download from Www.Somanuals.com. All Manuals Search And Download.
6. USING THE OPTIONAL STAPLE SORTER
1.Description of the Main Components . . . . . . 122
2.Non-sort Copying . . . . . . . . . . . . . . . . . . . . . . 123
3.Sort or Staple Sort Copying . . . . . . . . . . . . . . 124
4.Group Copying . . . . . . . . . . . . . . . . . . . . . . . . 128
121
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DESCRIPTION OF THE MAIN COMPONENTS
When the optional staple sorter MG-2014 is attached to the copier, you can select the sort, group
or staple mode. Non-sort is automatically selected as the default mode.
Non-sort bin
key*
STAPLE
In the non-sort mode, copies exit
into this bin. However, they will
also go into the sort bins when
more than 250 sheets are copied
or depend-ing upon the size of
paper selected.
The lamp inside the key
lights when stapling is
possible or while stapling is
in progress.
Sort bins (Bins "1" ~ "20")
Stapler*
In the sort or group mode, all
copies exit into these bins.
However, when more than 250
copies are set in the non-sort
mode, some of them will also
enter these bins.
Staple cartridge*
Stapler cover*
Note: See page 162 for the details of the staple sorter specification.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
2. NON-SORT COPYING
Check that NON-SORT, NON-STAPLE is
displayed on the Basic menu.
● If SORT , GROUP or STAPLE SORT is
1
displayed, press the key and select NON-
SORT, NON-STAPLE .
Place the original(s) on the original feed
tray or on the glass.
● See page 22 for how to set the original.
2
Paper size
Sort bins
Non-sort bin
Total
Key in the desired copy quantity.
● When 250 or less is copied at a time, all the
copies will exit into the non-sort bin.
When you use the optional automatic
document feeder, the total number of copies
(the number of originals X copy quantity)
should be 250 or less.
A4
1st~600th copy
(30 copies/bin)
601st~850th copy 850 copies
3
A3, B4
A4-R
1st~500th copy
(25 copies/bin)
501st~750th copy 750 copies
● When more than 250 is copied at a time, the
specified number of copies will exit into sort
bins "1" up to "20", then the remaining copies
will exit into the non-sort bin.
● If more than 850 (A4) or 750 (A3/B4/A4-R) is
copied at a time, the copier automatically
stops when 850 (or 750) copies have been
completed, and the following message
appears:
Remove paper from sorter bins
Remove all the copies from the staple sorter
and press the START key again to continue.
Select the desired copy size, reproduction
ratio, image density level, etc. if necessary.
4
5
Press the START key.
Note: When the staple sorter is working, do not
touch the bins.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
3. SORT OR STAPLE SORT COPYING
Example:
Making 5 sets of copies
from 5-page originals.
1
2
5 page originals
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
5 sets of copies
arranged in the same
order as the originals.
Sort or Staple Sort
Press the NON-SORT, NON-STAPLE key
on the Basic menu to enter the Sorter
menu.
1
● To select the SORT mode, press the SORT
key.
● To select the SORT/STAPLE mode, press the
STAPLE SORT key.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Place the original(s) on the original feed
tray or on the glass.
2
Using the automatic document feeder:
Place them with facing up and align the side
guides to the originals.
Stapling will be done in the position cor-
responding to the upper left corner of the
originals.However,inthe2in1mode,stapling
will be done in the position corresponding
to the lower right corner (see page 72).
2 in 1 stapling position
Stapling position
● The number of the originals you can set up
at a time is shown below.
2
2
2
Paper Weight
Mode
64~80g/m
Sort
—
50
25
81~90g/m
Sort
—
91~105g/m
Sort
—
Staple
—
Staple
—
Staple
—
A5-R
A4
50
25
(50)
40
25
30
25
(30)
40
20
20
20
(20)
A3, A4-R, FOLIO
)=Manual Stapling
(
Placing the originals on the glass:
Stapling position
Place the original face down on the glass. If
you start with the last page of your originals,
the copies will be arranged in the same page
order as the originals.
The copies can be stapled in the position
corresponding to the upper right corner of
the original.
In this case, however, copies are not stapled
automatically (see page 127 for manual
stapling).
Key in the number of copies (sets).
Up to 20 sets can be keyed in (all sizes).
3
4
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. as required.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
3. SORT OR SORT/STAPLE COPYING (Cont.)
Press the START key.
5
Using the automatic document feeder:
● The originals will automatically be fed in one
by one.
● If the sort/stapling mode is selected, all the
sets of copies will automatically be stapled
after copying is finished.
● If the copier stops during the sort or sort/
stapling mode and displays
Remove paper from sorter bins ,
remove all the copies from the staple sorter
and press the START key again to continue.
In this case, stapling is not possible.
Placing the original on the glass:
● After the copying of the first original (last
page) finishes, place the next original and
press the START key.
● Repeat this step until all the originals finish
being copied.
Pressing the STAPLE
key will cause
the copies in each bin to be stapled
automatically.
● While stapling is in progress, if you press the
6
STAPLE
Pressing the key again will resume stapling.
● The STAPLE key lamp comes on only
key again, stapling will stop.
when stapling is possible. However, if the
maximum number of copies that can be
stapled is exceeded, the STAPLE
key
lamp goes out, alerting the operator that
stapling is not possible.
Note: Do not open the stapler cover during
stapling in order to avoid a staple jam.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Stapling
Align the edges of the copies and insert
them into the first sort bin.
● Thecopiesshouldbeinsertedfullyinsideand
moved to the right and to the front until being
stopped.
1
2
● The STAPLE
key lamp will come on.
Copy
● The maximum number of copies is shown
below.
80g/m2 : 50 (all sizes)
90g/m2 : 30 (all sizes)
105g/m2 : 20 (all sizes)
Stapled
position
STAPLE
key
Press the STAPLE
key.
● The copies will be stapled.
Repeat steps 1 and 2 for the remaining sets
of copies.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
4. GROUP COPYING
Example:
Copying 5 originals
in the group mode.
1
2
3
4
5
5 originals
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
Press the NON-SORT, NON-STAPLE key
on the Basic menu to enter the Sorter
menu.
1
2
● Select the GROUP key.
Place the original(s) on the original feed
tray or on the glass.
● Up to 20 originals (all sizes) can be set at a
time.
● See page 22 for how to set the originals.
Key in the number of copies.
● The maximum number of copies that can be
set is 30 for A4, or 25 for A3, B4 or A4-R.
● You cannot set a different copy quantity for
each original.
3
Selectthedesiredcopysize, imagedensity
level, reproduction ratio, copy quantity,
etc. as required.
4
5
Press the START key.
Using the automatic document feeder:
● The originals will automatically be fed in one
by one and copied.
Placing the original on the glass:
● After the first original finishes being copied,
setthenextoriginalandpresstheSTARTkey.
● The copies of the second original will all exit
into the second bin, and those of the third
original into the third bin, and so on.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
7. WHEN THE GRAPHIC SYMBOLS FLASH
1.Add Paper Symbol . . . . . . . . . . . . . . . . . . . . . 130
2.Replace Toner Bag
Symbol. . . . . . . . . . 134
3.Add Toner
4.Clear Paper
1
Symbol . . . . . . . . . . . . . . . . . 136
Symbol . . . . . . . . . . . . . . . . 138
Misfeeding inside of the Copier . . . . . . . . 138
Misfeeding in the Automatic Duplexer . . . 143
Misfeeding from the Cassettes . . . . . . . . . 145
Misfeeding in the Large-Capacity Feeder . . 146
Misfeeding in the Automatic
2
3
4
Document Feeder . . . . . . . . . . . . . . . . . . . 147
Misfeeding in the Bypass Guide. . . . . . . . 148
Misfeeding in the Staple Sorter . . . . . . . . 149
5
6
5.Replacing Staples . . . . . . . . . . . . . . . . . . . . . . 150
6.Removing Jammed Staples . . . . . . . . . . . . . . 152
7.Call Service
Symbol . . . . . . . . . . . . . . . . 154
8.Periodic Maintenance . . . . . . . . . . . . . . . . . . . 154
129
Download from Www.Somanuals.com. All Manuals Search And Download.
1. ADD PAPER SYMBOL
When the paper supply in the selected cassette or the optional large-capacity feeder runs
out, the cassette or large-capacity feeder symbol on the display panel flashes and this
message appears:
Add paper
Add paper as described below.
Adding Paper to the Front Cassette
Pull out the cassette slowly until it comes
to a stop.
1
Place the paper in the cassette.
● Up to 600 sheets of paper (80g/m2) can be
Limit line
2
set. (See page 18.)
● Fan the paper well before placing it in the
cassette.
● Do not add paper above the line on the back
guide.
● Donotusecreased, folded, wrinkledordamp
sheets of paper.
Note: Check that there is a slight gap (about 0.5
Side guide
Side guide
mm) left between the paper and each of
the side guides as shown; the total gap
should not exceed 1 mm. If the gap is not
suitable, paper misfeeding may possibly
occur.
0.5mm
0.5mm
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Push in the cassette straight and slowly
until it comes to a stop.
● Make sure that the cassette is pushed in fully.
3
131
Download from Www.Somanuals.com. All Manuals Search And Download.
1. ADD PAPER SYMBOL (Cont.)
Adding Paper to the Large-Capacity Feeder (Optional)
Openthecoverofthelarge-capacityfeeder.
1
Note: If you want to add paper because the
paper supply has become low, press the
TRAY DOWN
key before opening
the cover. The elevator tray will
automatically move down and stop.
TRAY DOWN key
Guide plate at
Placethepaperinthelarge-capacityfeeder.
● Makesurethatallthesheetsareplacedneatly
aligned against the guide plates at rear side
on the elevator tray.
rear side
2
3
● Up to 1500 sheets of A4-size paper can be
placed. Do not add paper above the limit line
on the right.
● Do not use creased, folded, wrinkled or damp
sheets of paper.
Tip: Make sure that there is no gap between
the paper set and the guide plates at rear
side to avoid image skewing.
Elevator tray
Closethecoverofthelarge-capacityfeeder.
● The elevator tray will automatically move up
to the paper feeding position.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Paper Size of the Cassette
The paper size of the cassette can be changed to any of A3, B4, A4, A4-R and A5-R. Use the
following procedure.
Pull out the cassette slowly and fully.
1
Move the side guides so that the space
between them is slightly wider than the
desired paper size.
2
● To move the side guides, push the lever
(arrow q) to unlock.
1
Setthebackguidetothedesiredpapersize
(shown on the cassette surface).
● To move the back guide, push on its sides
(arrows w) to unlock and slide it with both
of your hands.
3
2
Place paper in the cassette.
● Forplacingpaperinthecassette, refertoStep
2in“AddingPapertotheFront Cassette”
on page 130.
4
Remove and reset the size mark plate so
that the desired paper size appears.
5
6
Size mark plate
Push in the cassette slowly and fully.
Paper size indicator
133
Download from Www.Somanuals.com. All Manuals Search And Download.
2. REPLACE TONER BAG
SYMBOL
When the toner bag becomes full of used toner, the
REPLACETONERBAG
message appears:
symbolflashesandthis
Dispose of used toner
Press INFO
Replace the toner bag as described below.
Replacing Procedure
Open the right-hand front cover.
1
Open the left-hand front cover.
2
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Removetheusedtonerbagfromthecopier.
● Take out the toner bag in the direction of the
arrow.
3
4
5
Close the used toner bag.
● The cap is provided on the used toner bag.
Set the new toner bag in the copier.
● Set it in the reverse procedure of step 3.
Close the left-hand front cover.
Close the right-hand front cover.
6
7
Note: The used toner bag should be disposed
of properly.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ADD TONER
SYMBOL
When the toner supply in a toner cartridge runs
out, the ADD TONER symbol and the symbol
that shows the corresponding toner colour flash
and then the following message appears on the
Basic menu:
Install new Yellow toner cartridge
Press INFO
Replace the toner cartridge as described below.
Note: It is recommended that only toner
cartridge made or designated by Toshiba
be used in order to optimize copy quality.
Open the front covers.
1
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Grasping the holder of the toner cartridge,
slide the cartridge along the rail toward
you and remove it.
2
● The empty cartridge should be disposed of
properly.
Shake the new cartridge to the right and
left 5 or 6 times to loosen the toner inside.
3
4
Pull the seal out from the cartridge.
Grasping the holder of the new toner
cartridge, push it along the rail fully back
into the copier.
5
● If the toner scatters, wipe it completely off.
Close the front covers.
● The following message appears:
6
Wait adding toner
Thenthecopierautomaticallystartssupplying
toner.
● When the toner has finished being supplied,
the display panel returns to the Basic menu.
(It takes approximately 4 or 5 minutes until
the toner has finished being added.)
137
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL
When a paper misfeed occurs in the copier, the
CLEAR PAPER
following message will appear:
symbol flashes and the
r
t
Misfeed in copier
Press INFO
q
e
y
w
TheCLEARPAPER
symbolflashesindifferent
positions in the diagram depending on where the
paper has misfed. Remove the misfed paper as
described below.
1
Inside of the Copier
2
Automatic Duplexer
3
Cassettes/Large-Capacity Feeder
Automatic Document Feeder
Bypass Guide
4
5
6
Staple Sorter
1
:
Misfeeding inside of the Copier
Remove the copy receiving tray.
1
● If a staple sorter is attached, first pull it away
from the copier by lifting the release lever.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Open the right-hand front cover.
Open the left-hand front cover.
2
3
Open the exit cover.
4
5
6
Remove the misfed paper.
Open the bypass guide.
● Open the bypass guide cover, press the blue
button and open the bypass guide.
● Remove any misfed paper.
Blue
button
139
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL (Cont.)
Turn the knob near the entrance of the
transfer belt unit in the direction of the
arrow (anticlockwise) and remove any
paper that comes out.
7
Tip: If the CLEAR PAPER symbol flashes as
shown on the right, be sure to carry out
step 7. If this action is not sufficient, the
paper may be torn or it may be left in the
copier.
Turn the knob in the direction of the arrow
(clockwise) and pull out the transfer belt
unit.
8
Remove any misfed paper on the transfer
belt.
9
Caution:
Donottouchthedrumfaceandthetransferbelt.
Touching them may cause image failure.
140
Download from Www.Somanuals.com. All Manuals Search And Download.
If the misfed paper is gripped between the
rollers, remove it by rotating the lever in
the direction shown.
10
11
Caution: Be careful as the fuser and the guide
plate around it may be hot.
Open the fuser cover and remove any
misfed paper.
Fuser unit
Reinstall the transfer belt unit and turn the
knob in the direction shown (anticlock-
wise) until you hear a click.
12
13
Close the exit cover.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL (Cont.)
Close the sheet bypass.
14
Close the left-hand and right-hand front
cover, and reinstall the copy receiving tray
or the staple sorter.
15
142
Download from Www.Somanuals.com. All Manuals Search And Download.
2
: Misfeeding in the Automatic Duplexer
Remove the copy receiving tray.
● If a staple sorter is attached, first pull it away
1
from the copier by lifting the release lever.
Opentheexitcoverandremoveanymisfed
paper.
2
3
Lower the lower guide of exit side and
remove any misfed paper.
Lower guide of
exit side
Close the exit cover.
4
5
Reinstall the copy receiving tray or the
staple sorter.
143
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL (Cont.)
Pull out the automatic duplexer slowly
until it comes to a stop.
6
Caution: Be careful as the metal part of the
guide plate of the automatic duplexer may be
hot.
Holdingthehandleoftheupperguideplate,
lift it slowly and fully.
● Becarefulnottoallowtheguideplatetodrop.
● Remove any misfed paper.
7
Guide plate
Pushthelever,andthenholdingthehandle
of the lower guide plate, lift it slowly and
fully.
● Make sure that the guide plate is latched to
8
prevent it from dropping.
Lever
Close the lower guide plate.
● Holding its handle with your right hand, lift
9
the lever up to unlatch the guide plate and
lower it slowly.
Lower the upper guide plate slowly.
10
11
Push in the automatic duplexer slowly and
fully.
144
Download from Www.Somanuals.com. All Manuals Search And Download.
3
: Misfeeding from the Cassettes
Holdingitshandle,openthefeedsidecover
slowly.
1
2
3
Remove any misfed sheets of paper.
Close the feed side cover.
145
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL (Cont.)
3
: Misfeeding in the Large-Capacity Feeder
Open the large-capacity feeder.
● Holding its handle as shown, lift it to unlock
it and open the feeder slowly away from the
copier.
1
Remove any misfed sheets of paper from
the feeder as shown.
2
3
Close the large-capacity feeder slowly and
fully.
Openthelarge-capacityfeedercoverslowly
and remove any misfed paper from inside.
4
5
Close the feeder cover slowly.
146
Download from Www.Somanuals.com. All Manuals Search And Download.
4
: Misfeeding in the Automatic Document Feeder
Open the feed-side cover of the automatic
document feeder and remove any misfed
original.
1
Raise the automatic document feeder and
remove any misfed original.
● If an original is left on the glass. remove it.
2
3
Close the feed-side cover.
Close the automatic document feeder and
remove the originals.
4
147
Download from Www.Somanuals.com. All Manuals Search And Download.
4. CLEAR PAPER
SYMBOL (Cont.)
Open the exit cover of the automatic
document feeder and remove any foreign
matter such as bits of paper, paper clips,
etc.
5
Raise the automatic document feeder and
remove any misfed paper.
6
Close the automatic document feeder.
7
8
Reset any originals not copied under the
originals remaining in the original feed
tray and resume copying.
5
: Misfeeding in the Bypass Guide
Remove all the sheets in the bypass guide.
1
2
Aligntheedgesofthesheets, andsetthem
again on the bypass guide.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
6
: Misfeeding in the Staple Sorter
Remove any misfed paper in the staple
sorter bins.
1
2
3
Lift the release lever and move the staple
sorter slowly away from the copier.
Pull open the paper transport guide of the
staplesorterandremovethemisfedpaper.
Transport guide
Close the paper transport guide and return
the staple sorter to its original position.
4
149
Download from Www.Somanuals.com. All Manuals Search And Download.
5. REPLACING STAPLES
The STAPLE
symbol flashes on the staple
sorter when the following occur:
● The stapler of the staple sorter has run out of
staples and this message appears:
Set staple cartidge
● A staple has jammed in the stapler and this
message appears:
Examine stapler
Replacing Staples
Open the stapler cover.
1
Remove the empty staple cartridge
● Lift the cartridge slightly and slide it out.
2
150
Download from Www.Somanuals.com. All Manuals Search And Download.
Install a new staple cartridge.
● First remove the cap from the new staple
cartridge.
3
● Slide the new staple cartridge fully into the
stapler.
Close the stapler cover.
4
5
After replacing the staple cartridge, make
sure that the stapler operates correctly by
stapling a few sheets of paper as operation
test,referringto"ManualStapling"onpage
127.
● If the stapler does not operate correctly, carry
out test stapling 7 times until it operates
correctly.
If the stapler still does not operate correctly,
reset the staple cartridge.
Note: Donotremovethestaplecartridgeexcept
when you replace it with a new one.
151
Download from Www.Somanuals.com. All Manuals Search And Download.
6. REMOVING JAMMED STAPLES
Removing Jammed Staples
Turn OFF the power switch of the copier
and open the stapler cover and loosen the
wing nut that holds the stapler unit in
place.
1
Wing nut
Holding the stapler unit as shown, lift its
1
outer side slightly (arrow
) and take it
2
3
2
out slowly toward you (arrow
).
1
2
Holding the stapler unit with your one
hand, pushdowntheleverwithyourother
hand and hold it there.
Lever
152
Download from Www.Somanuals.com. All Manuals Search And Download.
Pull out the slider fully toward you (arrow).
Slider
4
Remove the jammed staple.
5
6
Push the slider fully in.
Slider
● Make sure that the lever has moved up to
latch the slider. If not, pull the lever up by
hand.
Lever
Replace the stapler unit in the staple sorter
and tighten the wing nut. Close the stapler
cover.
7
8
9
Remove the remaining sheets from the
staplesorterandturnONthepowerswitch.
Referring to page 127 "Manual Stapling",
staple a few sheets of paper manually to
check that stapling is performed correctly.
Wing nut
153
Download from Www.Somanuals.com. All Manuals Search And Download.
7. CALL SERVICE
SYMBOL
When the CALL SERVICE
symbol flashes, the
following message appears and copying is no
longer possible:
Call for service
The telephone number of your service technician
will be displayed.
Note it down, then turn the power switch off and
immediately call service for assistance.
Note: Since a heater is used to fix toner images to the copy paper, a safety circuit is incorporated
in this copier. After you turn on the power switch, if a certain temperature is not attained
within a certain period of time, the safety circuit assumes that something abnormal has
happened. This causes the operation of the copier to stop and flashes the CALL SERVICE
symbol. This can possibly occur when the temperature is low but even though the
copier is not malfunctioning. If this occurs, turn the power switch off and then on again.
Repeat this procedure twice and if the problem still persists, turn off the power switch
and call for service.
8. PERIODIC MAINTENANCE
Note: When the following message appears on
the message display:
Time for periodic maintenance (Colour)
or
Time for periodic maintenance (Black)
thisindicatesthatassistancefromaqualified
service technician is required. Call service
for assistance.
154
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1.Daily Inspection. . . . . . . . . . . . . . . . . . . . . . . . 156
2.Simple Troubleshooting . . . . . . . . . . . . . . . . . 157
155
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DAILY INSPECTION
Items
Countermeasure
Remarks
Items to Inspect
Every Day
Power switch ON/ Press the switch all the way and do not
If you are using the
copier as a network
printer, make sure if
youcanturnOFFthe
power before doing
so.
OFF status
forget to turn ON or OFF the power
(Make use of the Auto Power OFF and
Weekly Timer as well).
When cleaning, be
carefulnottoscratch
the glass.
Clean the original glass with a cloth
moistened with cleaning liquid and
wipe it off with a dry cloth.
Items to Inspect
Once A Week
Dirtyoriginalglass
Dirtyoriginalcover
When cleaning, be
carefulnottoscratch
the original cover.
Clean the original cover with a cloth
moistened with a neutral detergent.
Then, wipe off the detergent
completely with a dry cloth.
Clean the original transport belt of the When cleaning, be
reversing automatic document feeder carefulnottoscratch
with a cloth moistened with a neutral the belt.
detergent. Then,wipeoffthedetergent
Dirty original
transport belt
(Reversing auto-
matic document
feeder)
completely with a dry cloth.
156
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SIMPLE TROUBLESHOOTING
Status
Items to be Checked
Countermeasure
Reference
page
Copier
does not
start
Is the power cord plug firmly inserted
in the outlet?
Insert the power cord plug firmly.
Are the front covers firmly closed?
Are the bypass feed unit cover and
the large-capacity feeder cover firmly
closed?
Close the front covers properly.
Close the covers properly.
➜P 8
➜P 132,138
➜P 8
➜P 10,20
Close the exit cover properly.
Press the Energy Saver key to clear
the mode. (It takes a while until the
copier becomes ready.
Is the exit cover firmly closed?
Is the copier in the Energy Saving
mode?
Display
panel
does not
change
when
➜P 10,107
Input the correct ID code.
Is the ID code input? Is the ID code
correct?
keys or
icons are
pressed
➜P 9,117
Is a key copy counter used?
If you are using a key copy counter,
insert it into the slot.
Wait until the copier becomes ready.
Is the “Warming up” message
displayed?
➜P 94,109
Does the password of administrator Passwordofadministratorisrequired.
input screen appear?
Ask your copier manager.
➜P 10,49
Is interrupt copying set?
Press the INTERRUPT key to clear the
mode.
Close the cover firmly to shut out any
outer light.
Is the original cover firmly closed?
Istheoriginalcoverortheglassdirty?
Copies
are not
clear
Clean the original cover with a cloth
moistened with a neutral detergent or
the original glass with cleaning liquid.
Then, wipe off completely with a dry
cloth.
Clean the transport belt with a cloth
moistened with a neutral detergent.
Then, wipe the detergent completely
off with a dry cloth.
Is the transport belt of the automatic
document feeder dirty?
Are transparent sheets or double- The original is transparent and the ➜P 58
sided originals used?
paper colour or the other side of the
original shows through. Set the
background lighter.
Copy
density
is too
light
Install a new toner cartridge.
➜P 136
Has the “Install new toner cartridge”
message appeared?
Is the image density set lighter than Set the copy density properly in the
➜P 36
standard?
manual density mode.
157
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SIMPLE TROUBLESHOOTING (Cont.)
Status
Items to be Checked
Countermeasure
Reference
page
Set the copy density by manual ➜P 36,58
density mode, or set the background
adjustment properly.
Copy
Istheadjustmentoftheimagedensity
density is and background set darker than
too dark standard?
Copy
images
are
Place the original firmly on the glass
and close the original cover.
Does the entire original lie properly
on the surface of the glass?
Is the copy paper moist?
Replace with new paper.
blurred
Images
are
partially
missing
Are the original size and direction,
and the reproduction ratio suitable
for the paper size?
Select the same size of copy paper as
the original, or set the reproduction
ratio suitable for the paper size.
➜P 31,32
Isthemarginonthecopysetproperly?
Set a smaller image shift value.
➜P 62
Refer to the Function Combination
MatrixesintheOperator’sManualand
set again.
Are there functions that cannot be
combined set together?
➜P 164,165
Functions
cannot
be set
Install a new toner cartridge.
Desired
colour
does not
appear
➜P 136
Has the "Install new toner cartridge"
message appeared on the display
panel?
➜P 154
Has "CALL SERVICE" message
appeared on the display panel?
Call your service technician.
Replace with new paper.
Is the copy paper moist?
Is the level of the image density and
colour adjustment correct?
➜P 36,52
53,54
55,56
58,59
94
Reset the image density and colour
adjustment to the standard settings.
If colour still deviates slightly, adjust
the calibration.
158
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS, ACCESSORIES &
OPTIONS
1.FC15/22 Specifications . . . . . . . . . . . . . . . . . . 160
2.Specifications of Options . . . . . . . . . . . . . . . . 161
3.Packing List. . . . . . . . . . . . . . . . . . . . . . . . . . . 163
4.Copying Function Combination Matrix . . . . . . 164
5.Image Quality Adjustment Combination Matrix . . 165
159
Download from Www.Somanuals.com. All Manuals Search And Download.
1. FC15/22 SPECIFICATIONS
Model Name
FC-15/FC-22
Type
Console type
Original Glass
Fixed
Copying System
Developing System
Fixing System
Laser electronic copying
Dry developing
Heat roller
Photosensor Type
Original Scanning System
OPC
Linear CCD sensor
Read: 600 dpi/256 gradation
Write: Corresponding to 9600dpi x 600dpi
(Primary scanning only: 16 division smoothing)
Sheets, books and three-dimensional objects
Resolution/Gradation
Acceptable Originals
Acceptable Copy Paper Size Cassette : A3 to A5-R
Sheet bypass : A3-wide to A5-R
Within 9 minutes (Room temperature 20°C)
During energy-saving: approx. 5min. or 2min. 30sec.
10.3 seconds (Full colour/Black, Manual density)
FC15: 15 copies/min. (Full colour), 22 copies/min. (Black)
FC22: 22 copies/min. (Full colour), 22 copies/min. (Black)
Up to 999 copies (digital key entry)
Warm-up Time
First Copy Time (A4)
ContinuousCopyingSpeed(A4)
Multiple Copying
Leading edge:5.0mm, Trailing edge:2.5mm,
Both edges:2.0mm
Excluded Image Width
Actual size : 100 0.5%
Original size : A3, A4, A5, B4, B5
Reproduction Ratio
Paper Supply
Paper size : A3, A4, A5, B4, B5
25 to 400% (in 1% increments)
* Independent scaling possible in the adjustment mode.
Cassette : 600 sheets (64~80g/m2) x 2+600 sheets (64~80g/m2) x 2
(optional)
Sheet bypass : 50 sheets (64~80g/m2)
Optional large-capacity feeder : 1500 sheets (64~90g/m2),
Optional large-capacity feeder : 1250 sheets (91~105g/m2)
Magnetic auto-toner system
Toner Density Adjustment
Colour Mode Selection
Full colour, Black, Auto-colour
Text/Photo, Text, Photo, Printed image, Map, Advance image
enhancement (Optional)
Original Mode Selection
Image
Quality
Density Control
Image Control
Automatic plus manual selection from 11 density steps
Hue, Saturation, Colour balance, RGB adjustment, Sharpness,
Background adjustment, One-touch adjustment
Automatic paper selection, Automatic magnification selection,
Interrupt, Energy save, Auto-clear, Auto shut off, Function clear,
Department management, Mode memory, Weekly timer, Date/
TimeSetting,Autojobstart,Automaticduplexcopying,OHPcassette
feeding/Thick paper cassette feeding, Original counting, Mixed
original mode, Change of language, Universal, User selection
Dual page, Edge erase, Image shift, Book centre erase, Mirror
image,Negative/Positivereversal,X-Yzoom,Imagerepeat,Centring,
Trimming, Masking, 2 in 1, 2 in 1 Duplex, Monocolor, Full image
Halogen lamp
Basic Copy Functions,
Special Functions
Editing Functions
Light Source
Power Requirement
Power Consumption
Dimensions
220-240V 50/60Hz, 9A
2.0kW
845mm(W) x 750mm(D) x 1000mm(H)
Weight
Approx. 191kg (not including toner and developer)
160
* Specifications and appearance are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SPECIFICATIONS OF OPTIONS
Automatic Duplexer
Type
MD-5007
Modular (cassette-type)
Minimum : A5-R
Acceptable Original Size
Maximum Capacity
Maximum : A3
Paper weight : Plain paper (64~90g/m2) mode only
50 sheets (A4, 64~80g/m2).
40 sheets (A4, 81~90g/m2).
633mm(W) x 626mm(D) x 110mm(H)
Approx. 9kg
Dimensions
Weight
Power Source
Power Consumption
5V, 24V (Supplied from the copier)
Up to 2.0kW (with the copier)
Reversing Automatic Document Feeder MR-3006E
Copy Sides
Number of Originals
Feeding Speed
Single-side, Duplex
Up to 50 originals (A4, 60~90g/m2) 40 originals (A4, 91~105g/m2)
Approx. 22 originals per minute (A4)
Minimum : A5-R
Acceptable Original Size
Maximum : A3
Paper weight : 60~105g/m2
Power Source
Power Consumption
Dimensions
24V (Supplied from the copier)
Up to 2.0kW (with the copier)
590mm(W) x 494mm(D) x 120mm(H)
Approx. 9.5kg
Weight
Key Copy Counter
MU-8 (Display, 6 digits), MU-10 (Socket)
* Specifications and appearance are subject to change without notice.
161
Download from Www.Somanuals.com. All Manuals Search And Download.
2. SPECIFICATIONS OF OPTIONS (Cont.)
20-bin Staple Sorter
Type
MG-2014
Console, Movable bins
Number of Bins
Feeding Mode
Bin Capacity
20bins+Receiving tray
Sort, Group, Non-sort, Staple
850 sheets (A4)
750 sheets (A3, FOLIO, A4-R)
250 sheets (A5-R)
*If more than 250 sheets are copied, paper exits to the sort
bins at first, then the rest exits to the non-sort bin.
50 sheets (A4)
25 sheets (A3, FOLIO, A4-R)
30 sheets (A4)
25 sheets (A3, FOLIO, A4-R)
64~209g/m2
Non-sort mode (64~105g/m2)
Sort mode(64~105g/m2)
Group mode(64~105g/m2)
Paper Type
Non-sort mode
Sort, Group mode
(length: 100~305mm, width: 148~457mm)
64~105g/m2
Position : One front stapling only
Number of copies : 50 sheets (64~80g/m2)
30 sheets (81~90g/m2)
Stapling Function
20 sheets (91~105g/m2)
*A5-R cannot be stapled.
24V (Supplied from the copier)
Up to 1.5kW (with the copier)
479mm(W) x 597mm(D) x 926mm(H)
Approx. 38.4kg
Power Source
Power Consumption
Dimensions
Weight
Large-Capacity Feeder
Acceptable Paper Weight
Acceptable Paper Size
Dimensions
MP-1501
Plain paper (64~105g/m2)
A4
317mm(W) x 460mm(D) x 288mm(H)
Approx. 8.5kg
Weight
Power Source
Power Consumption
5V, 24V (Supplied from the copier)
Up to 2.0kW (with the copier)
AI Board
KR-2030
Dimensions
Weight
145mm(W) x 140mm(D) x 10mm(H)
Approx. 150g
Power Source
Power Consumption
3.3V, 5V (Supplied from the copier)
Up to 2.0kW (with the copier)
* Specifications and appearance are subject to change without notice.
162
Download from Www.Somanuals.com. All Manuals Search And Download.
3. PACKING LIST
Unpacking/Set-up instructions
Copy receiving tray
Packing List
Operator’s manual pocket
Detachable cords (220-240V only)
Size mark plate of OHP film
* Specifications and appearance are subject to change without notice.
163
Download from Www.Somanuals.com. All Manuals Search And Download.
4. COPYING FUNCTION COMBINATION MATRIX
164
Download from Www.Somanuals.com. All Manuals Search And Download.
5. IMAGE QUALITY ADJUSTMENT COMBINATION MATRIX
165
Download from Www.Somanuals.com. All Manuals Search And Download.
PREVENTATIVE MAINTENANCE
PREVENTATIVE MAINTENANCE
Toshiba copiers are manufactured to the highest technical standards, using quality parts and
components, and are designed to meet all electrical safety and environmental requirements.
To ensure that optimum levels of performance and reliability are maintained, we strongly advise
that your copier receives regular visits for Preventative Maintenance at the copy interval
prescribed by Toshiba, which is:
30,000 copies Main Service
On models which incorporate a periodic maintenance message “TIME FOR PERIODIC
MAINTENANCE”onthemessagedisplay,thismessagewillnotifyyouthatpreventativemaintenance
has become necessary, when pre-programmed by your dealer technician.
To ensure that the aforementioned quality standards are maintained, we strongly recommend that
only Original Toshiba supplies and parts are used in your copier.
How to affix the PM labels
The labels have to be replaced by Service Technicians at the time of set up and each
PM time.
To Service Technicians:
At the time of set up and each PM, fill in the appropriate label with the current Total Counter reading,
the date and your signature, then peel off and affix the upper part of next PM sticker to the copier as
shown.
1. How to fill in the labels:
2. Affixing position
INFO
Compteur
Date
Signature
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycled paper is used for the inside pages of this book.
DIGITAL COLOUR PLAIN PAPER COPIER
OPERATOR'S MANUAL
FOR COPYING FUNCTIONS
This Operator’s Manual is printed with ink containing
soya bean oil.
FC15/22
1-1,KANDA NISHIKI-CHO,CHIYODAKU,TOKYO,101-8442,JAPAN
C
Copyright TOSHIBA TEC CORPORATION 1999
ALL RIGHTS RESERVED
4406581220
IN-F-312, 00-05 AB
Download from Www.Somanuals.com. All Manuals Search And Download.
|