Toshiba Computer Hardware SD R1612 User Manual

TOSHIBA AMERICA INFORMATION SYSTEMS  
STORAGE DEVICE DIVISION  
IRVINE, CALIFORNIA  
SD-R1612  
CD-RW/DVD-ROM COMBO DRIVE  
USER MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION – SD-R1612  
General Features  
CD-R/CD-RW disc write/rewrite at 52X/32X  
3-way Disc Eject (eject button, software, emergency eject hole)  
Average Random Access Time  
CD-ROM/CD-R  
CD-RW  
95ms  
110ms  
DVD-ROM - Single  
DVD-ROM - Dual  
110ms  
130ms  
DVD-RAM  
200ms  
Horizontal or Vertical Mount  
2MByte Buffer  
Playback interchangeability for CD-ROM and DVD-ROM discs  
Regionalization (RPC2 compliance) (DVD)  
BUS Interface - ATAPI  
Media Compatibility  
CD  
650MB CD-ROM (Read)  
80mm CD (Horizontal Mount Only)  
800/700/650MB CD-Recordable (Read&Write)  
700/650MB Low/High/Ultra Speed CD-Rewritable (Read & Write)  
DVD  
5/9/10/18G DVD Single/Dual (PTP, OTP) (Read)  
3.9/4.7G DVD-ROM  
DVDRW. DVDR, DVD-RAM  
80mm DVD (Horizontal Mount only)  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Types of Disc Formats Support – Read  
DVD:  
DVD-ROM (Book 1.02)  
DVD-video (Book 1.1)  
DVD-R (Book 1.0, 3.9G)  
DVD-R (Book 2.0, 4.7G) - General & Authring  
DVD+R (Version 1.0)  
DVDRW  
DVD-RAM  
CD:  
CD-DA (Red Book)  
CD-ROM (Yellow Book Mode1&2)  
CD-ROM XA (mode 2 Form 1&2)  
CD-I (Green Book, Mode2 Form 1&2, Ready, Bridge)  
CD-EXTRA/CD-Plus (Blue Book)  
CD-R (Orange Book Part II)  
CD-RW: HSRW (Orange Book Part III Volume1&2, USRW)  
Front Panel  
Figure 1.SD-R1612 DVD Writeable Drive Front Panel  
Load disc using tray.  
Loading Tray  
LED  
The LED lights green or amber when the drive is operating (LED is amber when drive is  
writing.)  
Load/Unload  
Button  
The Load/Unload button is used to open the disc tray so you can install or remove a disc.  
The emergency eject hole is to be used only when the Loading Tray will not open when  
Eject button is pressed.  
Emergency  
Eject Hole  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP – SD-R1612  
The following steps must be performed to properly install your drive:  
Set Drive Jumper Settings  
Connect Audio Cable  
Attach IDE BUS Cable  
Attach Power Cable  
Mount Drive  
Jumper Settings  
The mode select jumpers are 6 straight angle pins located on the rear of the Combo drive.  
By placing a jumper on the pins, you can select the following functions:  
CS  
SL  
MA  
Drive is configured using host interface signal CSEL  
Configures drive as Slave  
Configures drive as Master (default mode)  
Figure 1.Mode Select Jumper  
In most installations, jumper should remain in the MA position (factory default). It is recommended that  
you install your Combo drive only on the secondary IDE BUS. If you are installing on primary IDE BUS,  
your hard drive would then be the Master, and you should set your Combo drive to the Slave position  
(SL)  
Figure 2.Jumper Locations  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Placing Combo Drive inside your Computer  
Now that you have set the jumpers, you are ready to install your Combo drive inside your computer.  
Important Note: Disconnect power from your computer system before beginning installation.  
Remove computer cover and faceplate if required. Refer to your computer systems manual for removal  
information. If the Combo drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in  
your system.  
Your Toshiba Combo drive can be placed in any free half-height drive slot at the front of your computer.  
(It can be mounted horizontally or vertically.)  
Carefully start sliding the Combo drive into the opening with the disc tray facing the front of the computer.  
Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio cable and  
the Power cable on the back of the drive.  
Connecting Cables  
IDE BUS Cable (not supplied with drive) - Your computer system should have a primary and secondary  
IDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUS  
cable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the Combo  
drive's interface connector:  
If you are replacing your CD-ROM or DVD:  
connect Combo drive to the BUS Cable connector that  
the CD-ROM or DVD was connected to.  
If Combo drive is not replacing a CD-ROM/DVD or is an  
addition to a CD-ROM/DVD:  
connect Combo drive to an open connector on the  
secondary IDE BUS cable (not supplied with drive).  
If Combo drive is to be slave on Primary BUS:  
connect Combo drive to open connector on the primary  
IDE BUS cable (not supplied with drive).  
Figure 3.Installing BUS Cable  
Power Cable - Connect an internal computer power  
supply cable to the power socket at the back of the  
Combo drive. One side of the plug has chamfered  
edges, so the power connector fits only one way. Push  
plug completely into the socket making sure the plug fits  
correctly.  
Figure 4.Installing Power Cable  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Cable (optional) - If you have a sound card and  
speakers, and would like to play audio CDs on your  
computer, you will need to install a CD/DVD audio cable.  
Toshiba's Combo drives use a standard 4-pin audio  
cable that can be purchased from most local computer  
suppliers. The sound cable connects to your sound card  
at one end and the other end connects to the digital  
audio connector at the left rear of the Combo drive (see  
Combo drive Back Panel photo for location). Refer to the  
instructions that came with your sound card for details  
on any sound-driver software required.  
Figure 5.Installing Audio Cable  
Completing Installation  
After you have connected all the necessary cables,  
push the Combo drive completely into the computers  
drive slot. Mount drive per your computers  
instructions. The screw length should not exceed  
30.5mm (measured from outside surface of side or  
bottom of drive to tip of screw). Replace computer  
cover and all outer screws.  
Figure 6.Mounting Illustration  
Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows  
'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your  
drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If  
you prefer using DOS, download the DOS ATAPI driver from our web site.  
Other Software - Additional software is required to use the SD-R1612 CD-R/-RW and DVD functions.  
When you purchase the SD-R1612 as a kit, it will include the following software  
Nero6 OEM Suite Software – used to create CDs and view DVDs  
If you did not purchase the SD-R1612 as a kit, you will need to purchase third party software in order to  
view DVDs and create CD-R/-RW discs.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
USING THE DVD Combo Drive – SD-R1612  
Drive Operation  
Inserting a Disc - Horizontally  
To insert a disc into a drive that is mounted horizontally, perform the following steps:  
Figure 1.Inserting Disc  
1. Open the drive's Loading tray by pressing the Eject Button.  
2. Place disc or into drive's Loading tray  
3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.  
Inserting a Disc - Vertically  
To insert a disc in a drive that is mounted vertically, perform the following steps:  
1. Locate sliding disc holders (4 locations) on drive's Loading Tray.  
2. The vertical position of the drive (eject button up or down) determines which of these four sliding  
disc holders are used (see photo below). Position the disc behind 3 of the disc holders, two on  
bottom, and one on upper rear, closest to drive). Using all four holders may cause the disc to not  
set properly in tray.  
3. Slide the disc holders towards the center of tray using your finger, opened paper clip or the end  
of the emergency eject tool. The holder in the upper front side should be pulled away from the  
center of tray.  
4. Position the disc behind disc holders on upper and rear side of tray. Then put disc behind bottom front  
holder  
5. Check to see that all three disc holders are holding disc securely.  
6. Close the drive by gently pushing in the tray or pressing the eject button.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 2.Inserting Disc Vertically  
Removing a Disc  
To remove a disc from the Combo drive, perform the following steps:  
1. Open the Loading Tray by pressing the Eject Button.  
2. Slide disc holders away from disc.  
3. Grasp disc by edges, and lift out of loading tray.  
4. Press Eject Button again to close Loading Tray.  
Software  
When you purchase the SD-R1612 as a Kit, it will include Nero6 OEM Suite Software, which is used to  
create CDs and view DVDs.  
Usage Guidelines  
Keep the disc tray closed when not using the Combo Drive.  
Do not press down on the disc tray when opening or closing it.  
Do not place objects on the disc tray.  
Never use a damaged, broken, or deformed disc.  
Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc.  
To stop a DVD movie, click Stop button in the DVD player application program.  
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the  
disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed,  
causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed  
technology and do not indicate a problem with the drive.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Emergency Ejection  
CAUTION: The following procedure is intended only as a last resort when pressing the  
eject button fails to open the Loading Tray  
1. Turn computer power OFF by properly shutting down system.  
2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in until loading tray  
opens. Pull tray out.  
Figure 3.Using Emergency Eject  
Handling Media  
DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD  
movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-  
related and can be remedied by proper handling and care of media.  
Cleaning Media  
Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc  
accessing speed.  
If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather  
from the inner side outward.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING – SD-R1612  
Problem  
Solution  
Disc tray cannot be opened  
Check that there is power to drive.  
Use Emergency Eject instructions to open tray.  
Drive is not recognized by system  
Is the drive connected properly? Are all cables plugged in properly (e.g.  
Power Cable, Interface Cable and Audio Cables).  
Are the drive configuration jumpers on the Combo drive set properly?  
Is the software driver loaded? On a step-by-step (F8) Boot of the  
system is the Combo drive recognized?  
(BIOS / DOS reports "device driver not found" or "no valid drivers  
selected.). If not, Contact Technical Support.  
Has the Combo drive software driver been corrupted by a virus. Run a  
Virus Scan program and repair if possible. Contact Technical Support if  
the Virus renders the Combo drive software drivers not useable.  
Drive is not recognized by system  
during Boot process, but is  
recognized by the Operating  
System (i.e. XP, Win2000, Win98,  
Win NT, etc.)  
Is the Combo drive software driver loaded? On a step-by-step (F8) Boot  
of the system is the Combo drive recognized?  
(BIOS / DOS reports "device driver not found or no valid DVD drivers  
selected.). If not, Contact Technical Support.  
Has the Windows Combo drive software driver program been corrupted  
by a virus. Run a Virus Scan program and repair if possible. Contact  
Technical Support if the Virus renders the software drivers not useable.  
BUSY Indicator LED flashes  
slowly  
The disc may be dirty Clean it with a soft damp cloth. Avoid cleaning the  
disc using a circular motion. The disc should be wiped in a radial  
direction. That is, from the inner side outward.  
The laser lens may have become cloudy or blocked by particulate  
matter. Please contact Technical Support.  
BUSY Indicator LED is constantly  
ON  
Possible Hardware Problem. Please contact Technical Support.  
DVD-ROM can not play a DVD in  
the drive or certain types of CD  
media (i.e. CD-plus, etc.)  
Is the Combo drive driver loaded  
Is the DVD disc the correct format for the type of system that you are  
using? (i.e. on a PC an ISO9660 IBM compatible PC format as opposed  
to Apple/Mac HFS disc or UNIX disc formats which will not function).  
Do you have the correct software applications program/drivers installed  
to run a DVD disc?  
Has the Windows Combo drive software driver program been corrupted  
by a virus. Run a Virus Scan program and repair if possible. Contact  
Technical Support if the Virus renders the software drivers not useable.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS –SD-R1612  
General  
Interface ATAPI  
Formats for Writing  
Disc at once, Track at once, session at once, Variable & Fixed Packet Write  
CD-DA (Red Book)  
Format Compatibility: CD  
CD-ROM (Yellow Book, Mode 1&2)  
CD-ROM XA (Mode 2, Form 1&2)  
CD-I (Green book, Mode 2, Form 1&2, Ready, Bridge)  
CD-Extra/CD-Plus (Blue Book)  
Video CD (White Book)  
CD-R (Orange Book Part II)  
CD-RW: HSRW (Orange Book Part III, Volume 1&2)  
US-RW  
Format Compatibility: DVD DVD-ROM (Book 1.02)  
DVD-Video (Book 1.1)  
DVD-R (Book 1.0, 3.9G)  
DVD-R (Book 2.0, 4.7G) General & Authoring  
DVD+R (Version 1.0)  
DVD RW  
DVD-RAM  
Note: All DVD/CD formats, except CD-Red Book (audio), require additional application specific software  
and/or hardware. The drive is capable of reading these data formats. However, in order to run applications  
that use these formats, you must first have the required software and/or hardware.  
Data Disc Capacities  
DVD-ROM  
5/9/10/18G DVD-Single/Dual (PTP, OTP)  
3.9/4.7G DVD-ROM  
DVDRW, DVDR, DVD-RAM  
80mm DVD  
CD  
650MB  
80mm CD  
800/700/650MB CD Recordable  
700/650MB Low/High/Ultra Speed CD-Rewritable  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Performance  
Transfer Rate  
DVD (Single)  
DVD (Dual)  
CD  
21,600KB/second  
13,500KB/second  
7,800KB/second (mode 1)  
6,000KB/second (mode 1)  
CD-R/RW  
Random Access Time  
CD-ROM, CD-R  
CD-RW  
DVD Single  
DVD Dual  
DVDR/RW  
DVD-RAM  
95ms  
110ms  
110ms  
130ms  
130ms  
200ms  
Data Buffer  
2MB  
Environmental  
Temperature  
Operating  
Storage  
0° to 50° C (32° to 122° F)  
-40° to 65° C (-40° to 149° F)  
Relative Humidity  
Operating  
Storage/Shipping  
10% to 85%  
10% to 95%  
Shock (Non-operating)  
Acoustical Noise  
2ms [200G]  
Under 50dB (70 min disc)  
Power  
DC Voltage and Current Requirements  
5V 5%, 12V 10%  
Physical  
Height  
Width  
Depth  
Weight  
5.83" (148.2mm)  
1.65" (42mm)  
7.24" (184mm)  
1.65lbs (750g)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connectors  
DC input  
4-pin Power Supply Connector  
40 Pin I/F ATAPI Standard  
ATAPI Interface Connector  
Audio Connectors  
4-pin and 2-pin connector (use matching  
housing, Part No. 70066, made by Molex  
Corp, or equivalent)  
Regulatory  
The SD-R1612 Combo drive has been certified by the following regulatory agencies:  
UL 1950  
CSA C22.2 No. 950  
TUV (EN60950I)  
CE standard  
DHHS 21 CFR Sub-Chapter J  
FDA CFR21, EN60825  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DRIVE CONNECTORS –SD-R1612  
Figure 1.SD-R1612 Combo Drive Rear Panel - Connectors  
Power is supplied to your Combo drive by the connection with your computer's +5V/+12V  
Power  
power cable to the power socket at the back of drive. One side of the plug has chamfered  
edges, so the power connector fits only one way.  
Connector  
CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in  
upside-down with power ON.  
Supplies Analog and Digital sound to your system.  
Audio  
Connectors  
The SD-R1612 DVD drive is connected to your computer system through the ATAPI  
connector.  
ATAPI  
Connector  
The mode select jumpers are 6 straight angle pins located on the rear of the DVD drive.  
By placing a jumper on the pins, you can select the following functions: CL (CSEL), SL  
(Slave) or MA (Master). (see Setup for additional information).  
Mode Select  
Jumper  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 1.Interface Pin Assignments  
INTERFACE PIN ASSIGNMENT  
PIN  
NO.  
1
I/O  
SIGNAL  
NAME  
Reset  
GND  
HOST SIGNAL NAME  
PIN  
NO.  
21  
I/O  
SIGNAL  
NAME  
HDRQ  
HOST SIGNAL NAME  
DMA Request  
I
-
Host Reset  
O
-
2
22  
GND  
3
4
5
I/O  
I/O  
I/O  
HD7  
HD8  
HD6  
Host Data Bus BIT 7  
Host Data Bus BIT 8  
Host Data Bus BIT 6  
23  
24  
25  
I
-
I
HWR-,STOP  
GND  
Host I/O Write  
HRD-,  
Host I/O Read  
HDMARDY, -  
HSTROBE  
GND  
IORDY,  
DDMARDY,-  
DSTROBE  
CSEL  
HDAK-  
GND  
INTRQ  
IOCS16-  
HA1  
6
7
I/O  
I/O  
HD9  
HD5  
Host Data Bus BIT 9  
Host Data Bus BIT 5  
26  
27  
-
O
I/O Channel Ready  
8
9
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
-
HD10  
HD4  
HD11  
HD3  
HD12  
HD2  
HD13  
HD1  
HD14  
HD0  
HD15  
GND  
Host Data Bus Bit 10  
Host Data Bus BIT 4  
Host Data Bus BIT 11  
Host Data Bus BIT 3  
Host Data Bus BIT 12  
Host Data Bus BIT 2  
Host Data Bus BIT 13  
Host Data Bus BIT 1  
Host Data Bus BIT 14  
Host Data Bus BIT 0  
Host Data Bus BIT 15  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
-
I
Cable Select  
DMA Acknowledge  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
-
O
O
I
I/O  
I
I
I
I
Host Interrupt Request  
Host 16 BIT I/O  
Host Address Bus BIT 1  
Passed Diagnostics  
Host Address Bus BIT 0  
Host Address Bus BIT 2  
Host CHIP Select 0  
Host CHIP Select 1  
Drive Active/Drive 1  
Present  
PDIAG-  
HA0  
HA2  
HCS1  
HCS3  
I/O  
DASP-  
20  
-
(KEYPIN)  
40  
-
GND  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Teledyne Marine Instruments 465L User Manual
Toshiba Computer Drive MK4050GAC User Manual
Toshiba Network Router RBC FDP2 F PE User Manual
Toshiba TV DVD Combo 32LV17U User Manual
Tripp Lite Computer Accessories IN3006CG User Manual
Tripp Lite TV Cables p520 006 User Manual
Troy Bilt Snow Blower Squall2100 User Manual
True Fitness Elliptical Trainer 600EA User Manual
Vialta Digital Photo Frame VF 100 User Manual
Weed Eater Lawn Mower 405209 User Manual