TOSHIBA
SERVICE MANUAL
COLOURTELEVISION
14N21NS
PRINTED IN UK. 2002
C
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
6. AVOID AN X-RAY
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
Safety is secured against an X-ray by consider-
ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode-
ray tube.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
3. USE THE DESIGNATED PARTS
7. PERFORM A SAFETY CHECK AFTER
SERVICING
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
(INSULATION CHECK PROCEDURE)
1. Unplug the plug from the AC outlet.
2. Remove the antenna terminal on TV and turn
on the TV.
3. Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
4. If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
A1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SERVICING NOTICES ON CHECKING ......................................................................................................
HOW TO ORDER PARTS ...........................................................................................................................
IMPORTANT ................................................................................................................................................
CONTENTS .................................................................................................................................................
GENERAL SPECIFICATIONS ....................................................................................................................
DISASSEMBLY INSTRUCTIONS
A1-1
A1-1
A1-1
A2-1
A3-1~A3-5
1.REMOVAL OF ANODE CAP ..............................................................................................................
2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ...............................................................
SERVICE MODE LIST .................................................................................................................................
CONFIRMATION OF HOURS USED ..........................................................................................................
WHEN REPLACING EEPROM( MEMORY) IC ...........................................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................................
BLOCK DIAGRAM ......................................................................................................................................
PRINTED CIRCUIT BOARDS
B1-1
B2-1, B2-2
C-1
C-1
C-2
D-1~D-5
E-1, E-2
MAIN/CRT...............................................................................................................................................
SCHEMATIC DIAGRAMS
F-1~F-4
MICON/TUNER.......................................................................................................................................
CHROMA/SIF/VIF/21PIN ........................................................................................................................
POWER ..................................................................................................................................................
DEFLECTION/CRT .................................................................................................................................
SOUND AMP ..........................................................................................................................................
WAVEFORMS .............................................................................................................................................
MECHANICAL EXPLODED VIEW ..............................................................................................................
MECHANICAL REPLACEMENT PARTS LIST ..........................................................................................
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
G-9, G-10
H-1, H-2
I-1
J1-1
J2-1~ J2-4
A2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-1
TV
System
CRT
CRT Size / Visual Size
CRT Type
14 inch / 335.4mmV
Normal
Deflection
90
degree
Magnetic Field
BV/BH
+0.45G/0.18G
PAL
Color System
Speaker
1 Speaker
Bottom
1.5 x3.0 Inch
Position
Size
Impedance
MAX
10%(Typical)
8
ohm
1.0 W
0.8 W
Sound Output
DDR SECAM
No
NTSC3.58(AV)+NTSC4.43
PAL60Hz
Yes
Yes
G-2
Tuning
System
Broadcasting System
Tuner and
CCIR System B/G
1Tuner
System
Receive CH
Destination
Ohers
Tuning System
Input Impedance
F-Synth
VHF/UHF 75 ohm
E2 - E4, X - Z+2, S1 - S10, E5 - E12,
CH Coverage
S11 - S41, E21 - E69
B/G
Intermediate
Frequency
Picture(FP)
Sound(FS)
FP-FS
38.9 MHz
33.4 MHz
5.5 MHz
Preset CH
100
Stereo/Dual TV Sound
Tuner Sound Muting
Power Source
No
Yes
230V-240V AC 50Hz
G-3
G-4
Power
AC
DC
Power Consumption
at AC
44 W at AC 230 V 50 Hz
Stand by (at AC)
Per Year
Power Fuse
Safety
Radiation
X-Radiation
Operation
Storage
3
--
Yes
W at AC 230 V 50 Hz
kWh/Year
Protector
Regulation
CE(EN60065:98)
CE
-
+5oC ~ +40oC
-20oC ~ +60oC
Less then 80% RH
G-5
G-6
Temperature
Operating Humidity
A3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-7
On Screen
Display
Menu
Yes
Character
Yes
Menu Type
Picture
Contrast
Yes
Brightness
Colour
Yes
Yes
Tint (NTSC Only)
Sharpness
Audio
Yes
Yes
No
No
No
No
No
No
Bass
Treble
Balance
BBE On/Off
Stable Sound On/Off
CH Tuning
Matual
Yes
Yes
Yes
Yes
Yes
Auto
CH Allocation
Language
Clock Set
No
On/OffTimer Set
On Timer Set
Pin Code Registration
Panel Lock
Nicam Auto Off
AV Colour System
Sound System
Auto 4:3 Default
AV2 Output
Output Source
Source
Yes
No
No
Yes
Yes
No
No
No
No
No
No
Control Level
Volume
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Brightness
Contrast
Colour
Tint (NTSC Only)
Sharpness
Tuning
Bass
Treble
Balance
No
No
No
No
No
No
No
No
Back Light
Nicam ST
Tone 1/2 (A/B)
Surround On/Off
Pin Code
AV
Skip
Channel
Yes
Yes
No
Hotel Lock
Sleep Timer
Wide Mode
Sound Mute
No
No
No
Yes
G-8
G-9
OSD Language
English French Spanish
Germany Italian
Polski Turkey Sweden
Netherland Portgal
Norway Finland Denmark
Czech Slovak Hungarian
Russian Greek
Clock and
Timer
Sleep Timer
Max Time
Step
- Min
-
Min
Clock
No
No
On Timer
Off Timer
Wake Up Timer
Program( On Tim)
Program( 0ff Tim)
Yes
Yes
Timer Back-up (at Power Off Mode)
more than
--
Min
Sec
A3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-10
Remote
Control
Unit
RK-EY
(CT-835)
No
Glow in Dark Remocon
Format
Custom Code
Power Source
NEC
40-BF
3V
UM-4 x 2 pcs
32 Keys
Yes
h
Voltage(D.C)
UM size x pcs
Total Keys
Keys
Power
1
2
3
4
5
6
7
8
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
9
0
Volume Up / +
Volume Down / -
Previous
Select Picture
Menu
OK(Enter)
EXIT
No
Audio Select
Sleep Timer
Mute
TEXT / MIX / TV
CH Up / Page Up
CH Down / Page Down
Red
Green
Yellow
Cyan
TEXT F/T/B
Reveal
TIMED PAGE(SUB PAGE)
CALL / TEXT INDEX
INPUT SELECT
TEXT HOLD
TIME / TXCL
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
T'TEXT Keys
G-11
Features
Auto Degauss
Auto Shut Off
Canal+
No
No
No
CATV
Anti-theft(Back Up 30 Min.)
Memory(Last CH)
Memory(Last Volume)
BBE
Yes
Yes
No
Auto Search
CH Allocation
Just Clock Function
Game Position
CH Label
VM Circuit
Full OSD
Unitext
Yes
Yes
No
No
No
No
No
No
Fastext
Yes
Top Text
Premiere
Comb Filter
No
No
No
Lines
Auto CH Memory
Stable Sound
Auto Set Up
No
No
No
FBT Leak Test Protect
Power ON Memory
Previous (Quick View)
Panel Lock
Yes
Yes
Yes
Yes
Double Focus & Dynamic Focus
Wss Signal Wide Change
Virtual Dolby Surround
Hotel Lock
No
No
No
No
A3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-12
Accessories
Owner's Manual
Language
Swedish, Norwegian, Danish,
Finnish, Turkish
w/Guarantee Card
No
Yes
Remote Control Unit
Rod Antenna
Yes
Poles
2Pole
Terminal
D-type
Loop Antenna
No
Terminal
-
U/V Mixer
No
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
No
No
No
Circuit Diagram
No
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
Quick Set-up Sheet
Battery
No
No
Yes (Owner's Manual In)
No
No
Yes
Yes
UM size x pcs
OEM Brand
UM-4 x 2 pcs
No
AC Cord
No
AV Cord (2Pin-1Pin)
Registration Card
PTB Sheet
No
No
No
300 ohm to 75 ohm Antenna Adapter
No
G-13
Interface
Switch
Front
Power (Tact Sw)
System Select
Main Power SW
Sub Power
No
No
Yes
No
Channel Up
Yes
Channel Down
Volume Up
Yes
Yes
Volume Down
AC/DC
Yes
Rear
No
TV/CATV Selector
Degauss
No
No
Main Power SW
Power
No
No
Indicator
Stand-by
No
Stand-by/ON , On Timer
Stand-by/ON
On Timer
Yes(Red , Green)
No
No
Terminals
Front
Rear
Video Input
Audio Input
Yes
Yes
EAR Phone
Other Terminal
Video Input(Rear1)
Video Input(Rear2)
Audio Input(Rear1)
Audio Input(Rear2)
Video Output
Audio Output
Euro Scart(21Pin)
S-INPUT
No
No
No
No
No
No
No
Euro Scart(21Pin)
RGB-INPUT
Yes ( x1 )
Yes ( x1 )
Component Input
Diversity
No
No
Ext Speaker
No
No
DC Jack 12V(Center +)
VHF/UHF Antenna Input
AC Outlet
D Type
No
G-14
G-15
Set Size
Weight
Approx.
Net (Approx.)
Gross (Approx.)
W x D x H (mm)
362 x 360 x 373
9.5 kg
( --- lbs)
( ---lbs)
11.5kg
A3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SPECIFICATIONS
G-16
Carton
Master Carton
Content
No
Sets
/--
----
--
Material
Dimensions
--
W x D x H(mm)
x
-- x --
Description of Origin
Yes
Yes
Gift Box
Material
Dimensions
Double/Brown
440 408 x 380
W x D x H(mm)
x
Design
As per Buyer's
Description of Origin
Yes
Natural Dropping At 1 Corner / 3
Drop Test
Edges / 6 Surfaces
Height (cm)
62
Container Stuffing
866
Sets/40' container
A3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY INSTRUCTIONS
3. After one side is removed, pull in the opposite direction to
remove the other.
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the
Anode Cap, make sure to discharge the Anode Cap's
potential voltage.
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a small
*
Do not use pliers to loosen or tighten the Anode Cap
terminal, this may cause the spring to be damaged.
amount of alcohol. (Refer to Fig. 1-3.)
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.
(Refer to Fig. 1-1.)
Location of Anode Cap
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.
GND on the CRT
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
CRT
Screwdriver
Support
Alligator Clip
GND on the CRT
Fig. 1-1
Fig. 1-4
2. Flip up the sides of the Rubber Cap in the direction of the
arrow and remove one side of the support.
(Refer to Fig. 1-2.)
4. Insert one end of the Anode Support into the anode button,
then the other as shown in Fig. 1-5.
Rubber Cap
CRT
Support
Fig. 1-2
Support
CRT
Fig. 1-5
5. Confirm that the Support is securely connected.
6. Put on the Rubber Cap without moving any parts.
B1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY INSTRUCTIONS
3. When IC starts moving back and forth easily after
2.REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
desoldering completely, pickup the corner of the IC using
a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Package IC to protect other parts from any damage.
(Refer to Fig. 2-1.)
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Blower type IC
desoldering
machine
Masking Tape
IC
(Cotton Tape)
Tweezers
Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
5. Absorb the solder left on the pattern using the Braided
Do not add the rotating and the back and forth
Shield Wire. (Refer to Fig. 2-4.)
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
IC pattern
Fig. 2-4
Fig. 2-2
B2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DISASSEMBLY INSTRUCTIONS
INSTALLATION
4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-
1. Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
tip Soldering Iron. (Refer to Fig. 2-8.)
IC
Thin-tip Soldering Iron
Soldering Iron
Fig. 2-8
5. Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Solder temporarily
Solder temporarily
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
Fig. 2-5
2. Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
(Refer to Fig. 2-6.)
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
Solder
Soldering Iron
IC
Supply soldering
from upper position
to lower position
Fig. 2-6
3. Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 2-7
B2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 2 seconds.
Remocon Key
Operations
Set Key
Reset the user setting items (PICTURE, VOLUME and LANGUAGE) to the initial state
for delivery.
VOL. (-) MIN
0
Initialization of the factory.
Do not use this for the normal servicing.
If you set a factory initialization, the memories are reset such as the
channel setting, and the POWER ON total hours.
NOTE:
VOL. (-) MIN
VOL. (-) MIN
1
6
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Writing of EEPROM initial data.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN
VOL. (-) MIN
8
9
Display of the Adjustment MENU on the screen.
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
CONFIRMATION OF HOURS USED
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
ADDRESS DATA
1. Set the VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel
button (6) on the remote control for more than 2 seconds.
3. After the confirmation of using hours, turn off the power.
Initial setting content of MEMORY IC.
INIT 01 00
CRT ON 0010
POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1
+ (ones digit value)
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
Note: No need setting for the position of the mark @ due to the adjustment value.
INI
00 --- 00 00 00 00 41 80 48 00 23 27 01 03 30 06 14
+0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
10 10 00 80 80 80 3C 40
@
20
@
@
9F
@
80 00 44
00
@
@
@
20
@
@
@
@
@
@
@
C0 00
@
00 18
@
@
0F
30 00
07 00 00 00 00 00 00 00 00 00 00 00
40 7F 6F 5F 4F 3F 39 34 2F 2D 2B 29 27 25 23 21 20
50 1F 1E 1D 1C 1B 1A 19 18 17 16 15 14 13 13 12 12
60 11 11 10 10 0F 0F 0E 0E 0D 0D 0C 0C 0B 0B 0A 0A
70 09 09 08 08 07 07 06 05 04 04 03 03 03 02 02 02
80 22 23 CD CF D2 D6 D9 96 98 9C 9D 55 56 58 5A 5C
90 5D 5E ---
---
--- ---
---
---
--- --- ---
--- ---
---
--- ---
Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT 01 00
CRT ON 0010
Fig. 1
3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press OK to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
6. Pressing OK will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
The unit will now have the correct DATA for the new MEMORY IC.
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
2-1: CONSTANT VOLTAGE
Place the set with Aging Test for more than 5 minutes.
Connect the digital voltmeter to TP501.
1.
2.
3.
4.
CAUTION
Set condition is AV MODE without signal.
• Use an isolation transformer when performing any
service on this chassis.
Adjust the VR501 until the DC voltage is 135 ± 0.5V.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
2-2: VCO
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
• When you exchange IC and Transistor for a heat sink,
apply the silicon grease on the contact section of the
heat sink. Before applying new silicon grease, remove all
the old silicon grease. (Old grease may cause damages
to the IC and Transistor).
1. Place the set with Aging Test for more than 10 minutes.
2. Connect the oscillator (38.9MHz) to TP001.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "VCO COARSE".
4. Press the VOL. +/- button on the remote control until
the "OK" appear on the screen. If the "OK" is not
displayed, select the "+" side on the changed from "+"
to "-".
5. Press the Page UP button once to set to "VCO FINE"
mode.
6. Press the VOL. +/- button on the remote control to
select the 5 step down point from the upper limit on the
"OK".
Prepare the following measurement tools for electrical
adjustments.
1. Oscilloscope
2. Digital Voltmeter
3. Pattern Generator
(Example: In case of the "OK" range 30~41, select 36.)
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
2 seconds to appear the adjustment mode on the
screen as shown in Fig. 1-1.
2-3: AGC VOLTAGE
1. Place the set with Aging Test for more than 15 minutes.
2. Receive the VHF HIGH (63dB).
3. Connect the digital voltmeter to pin 5 of CP101.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (01) on the remote control to
select "RF AGC".
5. Press the VOL. +/- button on the remote control until the
digital voltmeter is 2.6 ± 0.05V.
2-4: CUT OFF
35 H POSI OSD
36 V POSI OSD
37 H POSI TEXT
38 V POSI TEXT
39 H POSI 60
117
57
117
57
1. Set condition is AV MODE without signal.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Place the set with Aging Test for more than 15 minutes.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (00) on the remote control to
select "CUT OFF".
45
00 CUT OFF
VCO Status
MMM
-
9- EXT
Fig. 1-1
2. Use the Channel button (0-9) or Channel UP/DOWN
button on the remote control to select the options
3. shown in Fig. 1-2.
5. Adjust the Screen Volume until a dim raster is obtained.
2-5: WHITE BALANCE
Press the MENU button on the remote control to end
the adjustments.
NOTE: Adjust after performing CUT OFF adjustment.
1.
2.
Place the set with Aging Test for more than 15 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "R DRIVE".
Press the Page UP/DOWN button on the remote control
to select the "R DRIVE", "G DRIVE", "M R CUTOFF" or
"M G CUTOFF".
Adjust the VOL. +/- button on the remote control to
whiten the R DRIVE, G DRIVE, M R CUT OFF, and M G
CUT OFF at each step tone sections equally.
Perform the above adjustments 5 and 6 until the white
color is looked like a white.
NO. FUNCTION
NO. FUNCTION
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
CUT OFF
RF AGC
AGC GAIN
R DRIVE
R CUTOFF
G DRIVE
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
TINT
SHARP
CONTRAST CENT
CONTRAST MAX
CONTRAST MIN
COLOR CENT
COLOR MAX
COLOR MIN
M R CUT OFF
M G CUT OFF
M B CUT OFF
CVBS OUT
APR THRESHOLD
BELL FILTER
BANDPASS
H POSI OSD
V POSI OSD
H POSI TEXT
V POSI TEXT
H POSI (60)
3.
4.
G CUTOFF
B DRIVE
H POSI (50)
V POSI (50)
V POSI (60)
V SIZE (50)
V SIZE (60)
VCO COARSE
VCO FINE
VCO COARSE L1
VCO FINE L1
BRIGHT CENT
BRIGHT MAX
BRIGHT MIN
5.
6.
7.
Fig. 1-2
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
2-6: FOCUS
2-10: BRIGHT CENT
1. Receive an 70dB monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.
1. Receive the PAL black pattern*. (RF Input)
2. Using the remote control, set the brightness and
contrast to normal position.
3. Place the set with Aging Test for more than 15 minutes.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
select "BRIGHT CENT".
5. Press the VOL. +/- button on the remote control until
the screen begin to shine.
6 Receive the PAL black pattern*. (Audio Video Input)
7. Set to the AV mode. Then perform the above
adjustments 2~5.
2-7: HORIZONTAL POSITION
1. Receive the monoscope pattern from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (08) on the remote control to
select "H POSI (50)".
4. Press the VOL. +/- button on the remote control until
the SHIFT quantity of the OVER SCAN on right and left
becomes minimum.
*The Black Pattern means the whole black raster signal.
Select the "RASTER" of the pattern generator, set to
the OFF position for each R, G and B.
5. Receive the monoscope pattern of NTSC. (Audio Video
Input)
2-11: CONTRAST CENT
6. Using the remote control, set the brightness and
contrast to normal position.
7. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (39) on the remote control to
select "H POSI (60)".
8. Press the VOL. +/- button on the remote control until
the SHIFT quantity of the OVER SCAN on right and left
becomes minimum.
1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select "CONTRAST CENT".
2. Press the VOL. +/- button on the remote control until
the contrast step No. becomes "27".
3. Receive a broadcast and check if the picture is normal.
4. Set to the AV mode.
5. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select "CONTRAST CENT".
2-8: VERTICAL POSITION, VERTICAL LINEARITY
1. Receive the monoscope pattern from the pattern
Generator.
6. Press the VOL. +/- button on the remote control until
the contrast step No. becomes "29".
2. Using the remote control, set the brightness and
contrast to normal position.
7. Receive a broadcast and check if the picture is normal.
3. Adjust the VR401 until the horizontal line becomes fit to
the notch of the shadow mask.
4. Adjust the VR420 until the SHIFT quantity of the OVER
SCAN on upside and downside becomes minimum.
2-12: COLOR CENT
1. Receive the PAL color bar pattern. (RF Input)
2. Using the remote control, set the brightness, contrast
and color to normal position.
3. Connect the oscilloscope to TP022.
2-9: VERTICAL SIZE
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (25) on the remote control to
select "COLOR CENT".
1. Receive the monoscope pattern from the Pattern
Generator.
2. Using the remote control, set the brightness and
contrast to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (11) on the remote control to
select "V SIZE (50)".
4. Adjust by using the VOL. +/- button on the remote
control until the SHIFT quantity of the OVER SCAN on
upside and downside becomes 8 ± 2%.
5. Receive a broadcast and check if the picture is normal.
6. Receive the monoscope pattern of NTSC. (Audio Video
Input)
5. Adjust the VOLTS RANGE VARIABLE knob of the
oscilloscope until the range between white 100% and
0% is set to 5 scales on the screen of the oscilloscope.
6. Press the VOL. +/- button on the remote control until
the red color level is adjusted to 100 ± 10% of the
white level. (Refer to Fig. 2-1)
7. Receive the PAL color bar pattern. (Audio Video Input)
8. Set to the AV mode. Then perform the above
adjustments 2~6.
7. Using the remote control, set the brightness and
contrast to normal position.
8. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (12) on the remote control to
select "V SIZE (60)".
9. Adjust by using the VOL. +/- button on the remote
control until the SHIFT quantity of the OVER SCAN on
upside and downside becomes 10 ± 2%.
10. Receive a broadcast and check if the picture is normal.
100%
Fig. 2-1
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
2-13: TINT
1. Receive the PAL color bar pattern. (Audio Video Input)
2. Using the remote control, set the brightness and
contrast to normal position.
3. Connect the oscilloscope to TP023.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (20) on the remote control to
select "TINT".
5. Press the VOL. +/- button on the remote control until
the section "A" becomes a straight line. (Refer to Fig.
2-2)
"A"
Fig. 2-2
2-14: Confirmation of Fixed Value (Step No.)
Please check if the fixed values of the each adjustment
items are set correctly referring below.
NO. FUNCTION
02 AGC GAIN
04 R CUTOFF
06 G CUTOFF
07 B DRIVE
09 V POSI (50)
10 V POSI (60)
18 BRIGHT MAX
19 BRIGHT MIN
20 TINT
RF
00
00
00
45
15
00
30
10
30
03
45
10
45
10
127
31
00
00
00
135
57
130
57
AV
---
---
---
---
---
---
30
10
ADJ.
07
45
10
45
10
---
---
---
---
---
21 SHARP
23 CONTRAST MAX
24 CONTRAST MIN
26 COLOR MAX
27 COLOR MIN
30 M B CUT OFF
31 CVBS OUT
32 APR THRESHOLD
33 BELL FILTER
34 BANDPASS
35 H POSI OSD
36 V POSI OSD
37 H POSI TEXT
38 V POSI TEXT
---
---
---
---
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
3-3: STATIC CONVERGENCE
3. PURITY AND CONVERGENCE
ADJUSTMENTS
NOTE
Adjust after performing adjustments in section 3-2.
NOTE
1. Receive the crosshatch pattern from the color bar
generator.
2. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
1. Turn the unit on and let it warm up for at least 30
minutes before performing the following adjustments.
2. Place the CRT surface facing east or west to reduce the
terrestrial magnetism.
3. Turn ON the unit and demagnetize with a Degauss Coil.
3. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1. Tighten the screw for the magnet. Refer to the adjusted
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body,
untighten the screw for the body.
2. Receive the green raster pattern from the color bar
generator.
3. Slide the deflection yoke until it touches the funnel
side of the CRT.
4. Adjust center of screen to green, with red and blue on the
sides, using the pair of purity magnets.
5. Switch the color bar generator from the green raster
pattern to the crosshatch pattern.
6. Combine red and blue of the 3 color crosshatch pattern
on the center of the screen by adjusting the pair of
4 pole magnets.
7. Combine red/blue (magenta) and green by adjusting the
pair of 6 pole magnets.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1. Adjust the differences around the screen by moving
the deflection yoke upward/downward and right/left.
(Refer to Fig. 3-2-a)
2. Insert three wedges between the deflection yoke and
CRT funnel to fix the deflection yoke.
(Refer to Fig. 3-2-b)
R G B
R G B
R
G
B
8. Adjust the crosshatch pattern to change to white
by repeating steps 6 and 7.
R
G
B
3-2: PURITY
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
NOTE
Fig. 3-2-a
Adjust after performing adjustments in section 3-1.
1. Receive the green raster pattern from color bar
generator.
2. Adjust the pair of purity magnets to center the
color on the screen.
Adjust the pair of purity magnets so the color at the
ends are equally wide.
WEDGE
WEDGE
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole
screen is green.
4. Confirm red and blue colors.
5. Adjust the slant of the deflection yoke while watching the
screen, then tighten the fixing screw.
WEDGE
DEFLECTION YOKE
DEFLECTION YOKE SCREW
MAGNET SCREW
WEDGE POSITION
Fig. 3-2-b
6 POLE MAGNETS
4 POLE MAGNETS
PURITY MAGNETS
Fig. 3-1
D-4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CD801
CRT
R807
R803
TP023
CP801
J801
CP802B
TP022
CRT PCB
CD802
J701
PH001
CP101
CP802A
CP401
FB401
VR401
VR420
TP001
CRT
R503
VR501
TP501
CP502
AC IN
CP1001
CRT
CD501
CP501
SPEAKER
J1001
J702
J703
MAIN PCB
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOCK DIAGRAM
VOL UP
TU001
AT+5V
MAIN W/T.TEXT
VOL DOWN
CH UP
IC101 OECF004A
SCL
4
SDA BPL AGC
IF
Q102
LED SW
Q103
LED SW
40 ON_TIMER
5
7
1
11
KEY_IN
SDA
D105
56
13
CH DOWN
I2C
ON TIMER
P.CON+5V
5
SDA
CHROMA
IC201 STV2246C
AVDD1
37
27
21
V-DRIVE
IC401 TDA8714A
SCL
SCL 14
6
STAND BY
8
6
7
AVDD2
AVDD3
OSD-B
9
OSD-B
34
35
36
29
39
MEMORY
IC199 S-24C04BDP-LA
AT+5V
Vs
10
1
P.CON+25V
OSD-G
OSD-R
OSD-G
10
11
29
30
7
POWER OUTPUT
TRIGGER INPUT
OSD-R
DY
OS101
VERT 47
3
1
57
50
REMORT
CVBSOUT1
XTAL2
CVBS2
CVBS1
AV1
SCL
51
52
48
I2C
OSC_OUT
FB401
X602
3.579545MHz
Q401
H.OUTPUT
SDA
X101
4MHz
Q402
40 XTAL1
1
H.DRIVE
X601
H_OUT
2
3
+B
51
OSC_IN
4.433619MHz
J801
B.OUT 30
P.CON+25V
Q803
BULE OUT
Q802
12
VCC_IF
G.OUT
R.OUT
31
32
F
8
F
S
3
53 VCC_D
P.CON+5V
P.CON+8V
VCC1
VCC2
45
17
HV
9
7
GREEN OUT
G_EXT/Y_EXT
B_EXT/U_EXT
R_EXT/V_EXT
27
26
Q801
RED OUT
11
FM_OUT
25
22
CRT
V801
Y/CVBS_IN3
55 AUDIO_OUT
INT_CVBS_OUT
CVBSIN2
13
20
14
EXT_AUDIO_IN
2
3
1
J701
J1001
R OUT
L OUT
VIDEO OUT
VIDEO IN
19
1
3
20
SOUND AMPIC
IC1001
FRONT VIDEO
J702
21-B IN
21-G IN
21-R IN
R IN
L IN
8
6
7
2
6
SPEAKER
SP1001
AN7511
2
5
3
1
2
11
15
SOUND+B
Vcc
AUDIO_SW
FRONT AUDIO
J703
IC703 NJM2233
2
7
3
1
2
Vout
Vin2
SW
1
Vin1
3
SW TRANS
T501
Q501
POWER
SW TR
5
D
9
SOUND+B
+B
12
15
16
P.CON+8V
AT+5V
P.CON+5V
E-2
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
L501_1
TP402
TP401
C505
R501
C526
C529
CP502
R502
B502
D523
C518
W017
W817
C524
R421
TH501
W052
W082
IC501
C542
R445
T401
D410
W836
W016
R510
C528
C440
R511
T501
Q402
R446
D508
D507
D518
VR501
R516
R536
W814
R512
R532
W094
C403
C634
B504
D505
Q505
Q507
W028
C1007
D514
W020
R528
D525
C446
C423
D102
D510
D108
W001
C517
W021
X101
C506
C514
R525
L101
R521
C531
C519
D512
Q504
R506
C418
W008
D515
W046
C515
Q511
C115
IC401
R405
R408
R703
R403
R409
W818
D509
D709
C414
C525
W820
R404
C1002
VR401
IC503
C1005_1
W060
VR420
C408
R710
D403
R402
W007
C422
W081
W078
W072
W012
B1001
C744
C745
W071
W010
W050
W861
L203
R740
W049
IC199
C121
W048
L702
W069
R213
C711
C220
W070
R706
R707
R619
C631
C604
W829
CF303
CF201
L204
R122
W067
C210
W803
W047
CF205
C209
C803
C216
C602
R804
R807_1
C217
W100
TP023
TP024
L207
IC201
TU001
R802
D001
C006
R003
D602
R803_1
Q801
TP022
Q802
C617_1
C610
C632
X601
X602
D608
D611
W051
PH001
Q803
D603
R605
C613
W013
F-1
F-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED CIRCUIT BOARDS
MAIN/CRT (CHIP MOUNTED PARTS)
SOLDER SIDE
C806
R816
C804
R813
Q603
R618
R602
R646
C005 C004 R005
R639
R607
Q605
R611
R623
C207
C201
Q604
Q602
R219
Q204
R708
R217
R208
Q202
C746
R702
R214
R215
Q201
IC703
C119
R143
R1002
R617
C704
R615
R117
C116
R113C113
Q601
R420
R406
R419
R124
R709
R134
R138
C106
CUT
R123
R541
C1004
R1004
C135
17
Q102
C111
C112
R412
C413
Q103
C105
1
33
Q508
R515
C104
R110
49
R524
Q510
C701
R504
Q512
Q509
C110
C109
C108
R507
C703
C114
IC102
Q506
R128
R104
R116
R112
C513
C1006
R523
R530
R102
C532
CUT
C1009
F-3
F-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
ACCESSORY
MICON/TUNER SCHEMATIC DIAGRAM
ANT001
T4-216BP-BK
BT001
R03(AB)2PXGPI
RESET
8
8
(MAIN PCB)
IC102 R3111N311A/C
BT002
R03(AB)2PXGPI
NC 0
NC 0
TU001
TUWRF4EG-778F2
D105_1
LTL-1BEFJ
5
4
R145
270
G
TM101
R108
1.2K
RC-FK010
R139
390
R
OS101 RPM7138-H5
VCO
TP001
0
LED SW
KRA102SRTK
Q103
4.8
NC
NC
NC
NC NC
R104
820
R102
2.2K
R109
2.2K
1
2
3
4.8
4.9
4.9
0
PH001
003P-2100
D104 C110
C122
R135
150
LED SW
KRC111SRTK
Q102
1SS133 0.47
B
16V 10
KA
7
7
3.6
4.8
C120
FROM/TO
CHROMA/SIF/VIF/21PIN
4.8
FROM/TO SOUND AMP
1
B
R105
10K
A_MUTE
AV1
POWER
R125
RF_AGC
IF
68 1/4W
SCL
SDA
VIDEO_OUT
1
FROM/TO
CHROMA/SIF/VIF/21PIN
6
6
2
OSD_FB
OSD_R
NC
16
0
4.8 3.0 3.0 1.2 1.2 1.2 1.2
15 14 13 12 11 10
0
8
0
7
0
6
0
5
0
4
4.8 4.8
3
0
1
9
2
0
NC
OSD_G
OSD_B
TU/RGB
4.8
0
0
NC
R131
TU/RGB
SCART1
SCART2
PO.6
NC
4.7K 1/4W
0
0
FROM/TO
CHROMA/SIF/VIF/21PIN
WSCF
VPP
MICON
IC101
OECF005A
R141
4.7K
0
0
0
NC
W820
4.8
4.8
1.6
H_CONT
PROTECT
CVBS_TXT
HD
5
5
AVDD3
TEST0
4.8
NC
PO.7
C113
4.8
4.8
4.8
4.8
CC001
FROM/TO POWER
MCFM
JTCK
RESET
REMORT
KEY_IN
22P CH
C116
4.8
NC
GND
17 NC
32 NC
64 VDD
48 GND
FOR_VCR
V_OUT
P.CON+5V
0.0047
B
C106 R111
2.2
TXCF
+B
0.0022
B
15K
0.2
NC
CVBSO
AVDD2
JTMS
CVBS2
P.FAIL
POWER FAIL
P4.6
R120
10K
0
NC
4.8
EMERGENCY
POWER
4.8
NC
3
0
C105
DEGAUSS
EMERGENCY
OSC_IN
DEGAUSS
R144
4
3
2
4
3
2
R117
270
0.1
B
C111
0.7
4.8
2.2
2.2
4.8
AT+5V_AVDD
AT+5V_DVDD
10K
C109
22P
X101 4MHz
100CT4R013
82P CH
C112
C135
2.1
CH
CVBS1
AGND
68P CH 0.47
B
CP101
0
06JQ-ST
OSC_OUT
VDD
C108
GND
I2C SCL
I2C SDA
I2C OFF
RF AGC
VIDEO OUT
1
2
3
4
5
6
L101
0
NC
22P
CH
C114
0.1
10uH 0305
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
B
R121
C115
0 NC
0
0
1.9 4.8 3.0 2.5 4.8
0 NC4.8
5
0 NC 0 NC 0 NC 0 NC 0 NC
0
R122
100 1/4W
4
6.3V 2200 YK
75 1/4W
C102
0.1
6
B
C131
16V10 KA
1K
R128
4.8
0
4.8
4.8
5
8
1
7
2
6
3
L102
4
0
0
0
0
10uH 0305
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
1
PCB010
TNB537
A
B
C
D
E
F
G
H
G-1
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
CHROMA/SIF/VIF/21PIN SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
5.0
3.9
SIF BUFFER
Q204
7
7
7
2SC2412K
3.2
C629
R208
1K
16V 10 KA
W822
CF202_3
TSF5330U
7.0
0.8
L204
10uH
7.9
C204
VIF PRE.AMP
Q201
KTC3881S-RTK
W829
W835
IN IN G OUTOUT
2.9
BUFFER
Q202
2SC2412K
0
0
1
2
3
4
5
1.5
S101Y
0.0022
B
0
S101X
RGB SW
Q601
2SC2412K
2.28
8
R217
1K
9
FROM/TO POWER
C212
0.001
VCO COIL
L207
10
6
6
B
P.CON+8V
GND
3700005
P.CON+5V
21PIN
J701
0350_9982_05
NC
R205
560
C201
3P CH
R702
3.3K
L702
10uH
R714
75
NC
1
NC
2
NC
3
NC
23
R706
2.7
2.8
4.8
3.1
2.7
2.5
2.5
4.5
2.0
0
3.6
11
4.9
12
3.8
13
2.4
14
3.8
15
3.9
16
7.8
17
4.1
18
0
19
3.2
20
2.8
21
3.2
22
1.7
1.7
24
3.4
25
3.6
26
3.4
27
0
28
5
5
4
5
6
7
8
9
10
R703
1K 1/4W
10K 1/4W
NC
R707
R715
75
1K 1/4W
NC
R713
75
R708
1K
R221
75
4
3
2
4
3
2
56
55
54
53
52
51
50
4.2
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
FROM/TO SOUND AMP
AUDIO_OUT
1.5
4.5
0
4.9
5.0
5.0
5.2
12
2.0
4.6
5.4
7.8
5.0
0
2.8
2.4
2.2
13
0
0.2
0
4.1
4.2
4.8
4.5
1.7
14
1.7
15
2.6
16
4.4
NC
11
C617_1
R709
75
22 16V KA
D709
FRONT_VIDEO_IN
H.CONT
Q603
2SC2412K
5.1
0
MTZJ5.1B
SW_AUDIO_IN
SCART_AUDIO
FROM/TO DEFLECTION/CRT
0.4
B.OUT
G.OUT
R.OUT
H_OUT
VAMP
ABCL
FROM/TO MICON/TUNER
TU/RGB
IF
RF_AGC
H_CONT
SDA
V_OUT
AFC
R602
100
BUFFER
Q605
2SC2412K
4.6
4.0
8.3
R606
100
SCL
HD
D604
11E1-EIC
PROTECT
FROM/TO MICON/TUNER
8.3
0
PROTECT
Q604
KRA102SRTK
17
V_OUT
R647
VIDEO_OUT
8.3
560 1/2W
CVBS_TXT
OSD_B
OSD_G
OSD_R
OSD_FB
FOR_VCR
8.3
C631
50V 33 YK
PROTECT
Q602
2SC2412K
0
0
R620
270 1/4W
CAUTION: DIGITAL TRANSISTOR
PCB010
TMB537
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
1
A
B
C
D
E
F
G
H
G-3
G-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
(MAIN PCB)
POWER SCHEMATIC DIAGRAM
8
8
C509
FROM/TO SOUND AMP
500V 470P B
D505
R517
SOUND+B
P.CON+8V
SOUND_GND
GND
SB290S
5.6 2W
W861
W833
R506
22K 1/4W
EMERGENCY
Q504
0
D506
2SA1624
7
7
134.8
135.0
1SS133
C531
0.1
0.0
R528
RELAY SW
Q505
KTC3203_Y
0.7
50V 22 MHE
R521
10K 1/4W
FROM/TO DEFLECTION/CRT
68K 1/4W
C517
GND
2KV 0.001 R
D510
P.CON+8V
RY501
ALKS321
R503
2
1
4
TP502
L503
8R140018
(028R140027)
+B_135V
H.DRV+B
RU2AM-EIC
1.2 2W
(LK1aF-12V)
3
CP502
A1561WV2-2P
IC503
KIA78R09API
FROM/TO
CHROMA/SIF/VIF/21PIN
1
2
TH501
6
6
B59104-J80-A10
(J104-A80-A10)
T501
81290974
P.CON+8V
P.CON+5V
GND
0
NC
NC
10
1
2
3
4
R501
0
R509
270
11.2
8.0
0
5.0
8
7
6
5
D513
11
5.6 5W
0.22 1W
C502
0
12
SB290S
2
4
1
3
2KV 0.001 B
SW501
SDKVA30100
0
D517
270
400
13
2
11E1-EIC
0
F501
4
1
5
6
L501_1
0R7A223F24Y
14
T4A_L_250V
NC NC
3
D501
FROM/TO MICON/TUNER
+B
5
5
AC230V_50Hz
CD501_1
0
GBL06L-6177
1
3
4
15
06655827
C503
2
0
FH501
FH502
NC
0
3
2
1
GND
P.FAIL
16
2KV0.001 B
BLUE
EYF-52BC EYF-52BC
4.9
0
D525
MTZJ12B
BROWN
C524
D511 R526
R507
2.2K
4.2
R508
10K
P.FAIL
Q506
17
2KV1000P
R
1N4937 100 1/4W
4.9 2SA1037AK
0
18
D516
0
AT+5V_AVDD
P.CON+5V
DEGAUSS
BLUE
CP501
SB290S
C520
BROWN
A3963WV2-3PD
W836
500V 470P B
IC502
KIA7806API
AT+5V_DVDD
POWER
D
S
POWER
Q501
2SK2647-01MR
4
3
2
4
3
2
R522
G
EMERGENCY
4.7 1/4W
P.CON SW
Q511
KTA1281_Y
5.1
R534
56K
R535
1K 1/4W
1
2
3
5.0
8.0
0
6.0
4.4
R515
R533
470
C543
D509 10K
11E1-EIC
0.33
B
HS501
763WAA0170
HS502
763WAA0186
0.1
R525
1K 1/4W
D502
MTZJ3.6B
4.7
R532
1K 1/4W
P.CON SW
Q510
W817
NC
7
8.8 11.5 180
270
KRC103SRTK 0
5
6
8
1
EMERGENCY
Q509
KRC111SRTK
6.8
12.33
0.32
9.07
8.05
R512
470 1/4W
D518
1SS133
0
0
C530
0.1
R541
B
FEED BACK
SWITCHING
Q507
D508
R511
4
3
2
FEED BACK
7.7
5.6
1N4937 47 1/2W
IC504
27K
0
1.1
0
17.5
KTC3198
LTV-817M-VB
6.2
R530
680K
D507
0
R519
100
KRC111SRTK
Q508
EMERGENCY
0
1SS133
R510
EMERGENCY
Q512
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
4.9
R523
1K
820K 1/4W
KRA102SRTK
0
4.9
4.9
NC
ATTENTION: LES PIECES REPAREES PAR UN
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
ETANT
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PCB010
TMB537
1
1
DESCRIBED IN PARTS LIST ONLY
A
B
C
D
E
F
G
H
G-5
G-6
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
(MAIN PCB)
DEFLECTION/CRT SCHEMATIC DIAGRAM
8
8
FROM/TO
GND
CUT OFF
G.OUT
R.OUT
B.OUT
NC
1
2
1
2
GND
CHROMA/SIF/VIF/21PIN
R422
CUT OFF
G.OUT
R.OUT
B.OUT
NC
820 1/4W
G.OUT
R.OUT
B.OUT
3
3
4
4
5
5
NC
NC
6
6
NC
NC
V-DRIVE
IC401
TDA8174A
V_OUT
VAMP
ABCL
HEATER
GND
7
7
HEATER
GND
8
8
ICATH
180V
9
9
ICATH
180V
10
10
H_OUT
AFC
18
FROM/TO CRT
FROM/TO DEFLECTION
7
7
1
2
3
4
5
6
7
8
9
10
11
CP802A
B2013H02-10P
CP802B
B2013H02-10P
14.5 23.0
5.0
6.4
4.4
0.0
12.0 12.0
4.4
25.0 1.7
R404
330K +-1% M
CP801_1
003P-2100
19
D403
1
11E1-EIC
RED OUT
Q801
GREEN OUT
Q802
BLUE OUT
Q803
3.2
3.2
3.2
20
KTC3207
KTC3207
KTC3207
6
6
100.6 2.7
98.4
2.7
95.4 2.7
CD801
SM1573-001
1
R419
1.2K
R406
6.8K
R420
10K
V801
A34AGT13X98(L)
(CPJ370BVBK1U-TC)
5
4
3
2
1
TP022
9
10
8
G
6
TP023
TP024
24
25
26
R
HS401
763WSAA013
NC
B
11
5
7
1
5
5
CP401
A1561WV2-A5P
R429
1W
23
4.7
T401
ETH09K14BZ
21
3
2
1
4
130
22
H.OUTPUT
Q401
2SD2499
6
0
0
H.DRIVE
Q402
FB401
3214034F
2SC1627_Y
27.0
0
4
3
2
4
3
2
130 COL
1
HV
FROM/TO POWER
0.3
0
E180
R424
6
H.DRV+B
GND
135 B+
180 1W
2
P.CON+8V
+B_135V
0
AFC
NC 9
FOCUS
FOCUS
HEA
TER
F
S
0
10
SCREEN
C819
2KV 0.001 B
0
8
0
GND
E12
GND
0
0
96.4
6.4
NC 4
11
0
3
E27
0
0
ABL
7
0
0
8
0
GND
E8
NC 5
101.6
99.6
J801
HPS3200-010501
D407
1SS133
PCB110
TCB396
R445
180K
1/4W
TP401
TP402
PCB010
TMB537
NC
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
NC
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION: SINCE THESE PARTS MARKED BY
ARE
1
1
NOTE:THE RESISTOR MARKED F IS FUSE RESISTOR.
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
IS NON POLAR ONE.
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
B
C
D
E
F
G
H
G-7
G-8
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
D
E
F
G
H
SOUND AMP SCHEMATIC DIAGRAM
8
8
(MAIN PCB)
J703
HTJ-032-05AW
R712
820 1/4W
28
7
7
L714
J702
HTJ-032-05AY
10uH 0305
27
C740
16V 10 KA
R740
220 1/4W
NC
5
0
8
4.4
8.3
0
7
2
6
3
6
6
SP1001
SPEAKER
CP1001
A2502WV2-2P
29
1
2
1
2
SA08A05BWB
W/WIRE
1
4
8.2
3.5
0
3.4
5.1
0
5.1
0 NC
5
4
6
7
8
+
-
B1001
2
3
1
W5RH3.5X5X1.0
3
2
1
5
5
HEADPHONE_JACK
J1001
MSJ-035-12A_PC
5.1
0
0.3
3.9
FROM/TO
CHROMA/SIF/VIF/21PIN
4
3
2
4
3
2
SW_AUDIO_IN
FRONT_VIDEO_IN
C1006
SCART_AUDIO
AUDIO_OUT
470P
B
C1003_1
R1004
150K
C1007
R1010
16V 22 KANP
16V 10 KA
33 1/2W
FROM/TO POWER
SOUND+B
P.CON+8V
SOUND_GND
GND
FROM/TO MICON/TUNER
AV1
A_MUTE
POWER
PCB010
TMB537
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
1
1
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
DESCRIBED IN PARTS LIST ONLY
A
B
C
D
E
F
G
H
G-10
G-9
Download from Www.Somanuals.com. All Manuals Search And Download.
WAVEFORMS
MICON/TUNER
20µs
1.00V
0.2ms
1.00V
500µs
50mV
6
1
11
CHROMA/SIF/VIF/21PIN
0.2ms
1.00V
2ms
20µs
200mV
0.50V
2
7
12
100ns
20mV
0.5µs
20µs
1.00V
1.00V
13
3
8
20µs
1.00V
20us
0.5µs
0.50V
1.00V
14
4
9
10ms
1.00V
20us
20µs
1.00V
1.00V
5
10
15
NOTH: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
Download from Www.Somanuals.com. All Manuals Search And Download.
WAVEFORMS
20µs
20µs
20µs
10.0V
50V
1.00V
21
26
16
SOUND AMP
500us
20µs
5.00V
20µs
5.00V
100mV
27
17
22
DEFLECTION/CRT
10us
10ms
1.00V
2us
200mV
200V
28
18
23
500us
10ms
10.0V
20µs
50V
500mV
29
19
24
10ms
10.0V
20µs
50V
20
25
NOTH: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL EXPLODED VIEW
202
112
202
202
204
202
201
110
202
PCB110
(CRT PCB)
201
114
115
201
201
206
206
102
207
205
113
103
PCB010
(MAIN PCB)
104
203
107
108
111
109
106
105
101
I-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
101
102
103
104
105
106
107
108
109
A3L804M720 CABINET,FRONT ASSY
752WSA0216 SHIELD,CASE
752WSA0272 SHIELD,AUDIO
752WSA0286 SHIELD,IC
701UPJ0305 CABINET,FRONT
713UPA0020 GUIDE,REMOCON
713UPA0021 GLASS,LED
735UPA0097 BUTTON,BASE
735UPB0013 BUTTON,FRAME
110
111
112
113
114
115
702UPA0239 CABINET,BACK
761WPAA060 HOLDER,PCB
7225490087 SHEET,RATING
735UPB0014 BUTTON,POWER
741WUA0020 SPRING,EARTH
899HV3T001 HOLDER,ANODE WIRE
201
202
203
204
205
206
207
8121J50B54 SCREW,TAPPING(B0) GW20
8117540A64 SCREW,TAPPING(B0) TRUSS
8110630A04 SCREW,TAP TITE(P) BRAZIER
8110630804 SCREW,TAP TITE(P) BRAZIER
8107630804 SCREW,TAP TITE(S) BRAZIER
8109I30804 SCREW,TAP TITE(B) WH7
8109630802 SCREW,TAP TITE(B) BRAZIER
5x28
4x16
3x10
3x8
3x8
3x8
3x8
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
A3L804N975 INSTRUCTION BOOK KIT
JB5XDA00
J3L80401
J3L80407
J3L80410
J3L80411
J3L80451
J3L80461
J3L80470
J3L80471
J3L80473
J3L80474
POLYBAG,INSTRUCTION(RED CAUTION)
INSTRUCTION BOOK(SWE)
QUICK SET-UP SHEET(SWE)
INSTRUCTION BOOK(NOR)
INSTRUCTION BOOK(DAN)
INSTRUCTION BOOK(FIN)
INSTRUCTION BOOK(TUR)
QUICK SET-UP SHEET(NOR)
QUICK SET-UP SHEET(DAN)
QUICK SET-UP SHEET(FIN)
QUICK SET-UP SHEET(TUR)
7230007526 SHEET,BAR CODE
791WHA0090 LAMIFILM,BAG
792UHA0165 PACKAGE,TOP
792UHA0166 PACKAGE,BOTTOM
793UCD1178 GIFT BOX
J1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
RESISTORS
REF. NO. PART NO.
DESCRIPTION
RESISTORS
R001
R002
R003
R004
R005
R006
R102
R104
R105
R106
R107
R108
R109
R110
R111
R112
R113
R114
R115
R116
R117
R120
R121
R122
R123
R124
R125
R128
R131
R133
R134
R135
R138
R139
R140
R141
R142
R143
R144
R145
R146
R201
R202
R203
R204
R205
R208
R213
R214
R215
R217
R218
R219
R221
R402
R403
R404
R405
R406
R407
R408
R409
R410
R411
R412
R416
R417
R419
R420
R421
R422
R424
R427
R429
R445
R446
R447
R002T2183J
R002T2183J
R002T4271J
R002T4271J
R801R7104J
R801R7153J
R801R7222J
R801R7821J
R801R7103J
R801R7103J
R002T4101J
R801R7122J
R801R7222J
R801R7562J
R801R7153J
R801R7473J
R801R7562J
R801R7472J
R801R7472J
R801R7103J
R801R7271J
R801R7103J
R002T4101J
R002T4750J
R801R7103J
R801R7103J
R002T4680J
R801R7102J
R002T4472J
R002T4101J
R801R7103J
R801R7151J
R801R7103J
R801R7391J
R801R7103J
R801R7472J
R801R7101J
R801R7101J
R801R7103J
R801R7271J
R801R7103J
R801R7820J
R801R7331J
R801R7102J
R801R7331J
R801R7561J
R801R7102J
R002T2221J
R801R7222J
R801R7682J
R801R7102J
R801R7151J
R801R7102J
R801R7750J
R002T2681J
R002T2681J
R4X5T6334F
R4X5T6394F
R801R7682J
R002T21R2J
R002T4102J
R002T2681J
R002T2681J
R3X28A391J
R801R7822J
R002T22R2J
R4X5T6332F
R801R7122J
R801R7103J
R002T4473J
R002T4821J
R3X181181J
R002T4101J
R655814R7J
R002T4184J
R002T2471J
R635U2680J
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
18K OHM 1/2W
!
R501
R502
R503
R504
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R516
R517
R518
R519
R521
R522
R523
R524
R525
R526
R527
R528
R530
R531
R532
R533
R534
R535
R536
R541
R601
R602
R605
R606
R607
R608
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R620
R621
R622
R623
R625
R628
R629
R630
R636
R638
R639
R640
R641
R643
R644
R645
R646
R647
R702
R703
R706
R707
R708
R709
R710
R712
R713
R5X2CD5R6J R,CEMENT
5.6 OHM 5W
1.5M OHM 1/2W
1.2 OHM 2W
18K OHM 1/2W
270 OHM 1/4W
270 OHM 1/4W
100K OHM 1/10W
15K OHM 1/10W
2.2K OHM 1/10W
820 OHM 1/10W
10K OHM 1/10W
10K OHM 1/10W
100 OHM 1/4W
1.2K OHM 1/10W
2.2K OHM 1/10W
5.6K OHM 1/10W
15K OHM 1/10W
47K OHM 1/10W
5.6K OHM 1/10W
4.7K OHM 1/10W
4.7K OHM 1/10W
10K OHM 1/10W
270 OHM 1/10W
10K OHM 1/10W
100 OHM 1/4W
75 OHM 1/4W
10K OHM 1/10W
10K OHM 1/10W
68 OHM 1/4W
1K OHM 1/10W
4.7K OHM 1/4W
100 OHM 1/4W
10K OHM 1/10W
150 OHM 1/10W
10K OHM 1/10W
390 OHM 1/10W
10K OHM 1/10W
4.7K OHM 1/10W
100 OHM 1/10W
100 OHM 1/10W
10K OHM 1/10W
270 OHM 1/10W
10K OHM 1/10W
82 OHM 1/10W
330 OHM 1/10W
1K OHM 1/10W
330 OHM 1/10W
560 OHM 1/10W
1K OHM 1/10W
220 OHM 1/2W
2.2K OHM 1/10W
6.8K OHM 1/10W
1K OHM 1/10W
150 OHM 1/10W
1K OHM 1/10W
75 OHM 1/10W
680 OHM 1/2W
680 OHM 1/2W
330K OHM 1/6W
390K OHM 1/6W
6.8K OHM 1/10W
1.2 OHM 1/2W
1K OHM 1/4W
680 OHM 1/2W
680 OHM 1/2W
390 OHM 2W
R002T2155J
R3X18A1R2J
R801R7562J
R002T4223J
R801R7222J
R801R7103J
R63581R22J
R002T4824J
R002T2470J
R002T4471J
R801R7561J
R002T2563J
R801R7103J
R002T4331J
R3X18A5R6J
R4X5T6222F
R801R7101J
R002T4683J
R002T44R7J
R801R7102J
R801R7561J
R002T4102J
R002T4101J
R3X181R33J
R002T4103J
R801R7684J
R801R7102J
R002T4102J
R801R7471J
R801R7563J
R002T4102J
R002T4224J
R801R7273J
R801R7472J
R801R7101J
R002T4221J
R801R7101J
R801R7223J
R801R7473J
R801R7122J
R801R7332J
R801R7332J
R801R7332J
R801R7152J
R801R7152J
R801R7152J
R801R7102J
R801R7103J
R002T4103J
R002T4271J
R002T4561J
R801R7334J
R801R7102J
R801R7750J
R801R7271J
R801R7271J
R801R7271J
R801R7473J
R801R7222J
R801R7562J
R801R7273J
R801R7223J
R801R7471J
R801R7272J
R801R7222J
R801R7822J
R002T2561J
R801R7332J
R002T4103J
R002T4102J
R002T4102J
R801R7102J
R801R7750J
R002T4750J
R002T4821J
R801R7750J
RC
R,METAL OXIDE
RC
RC
RC
RC
R,FUSE
RC
RC
RC
RC
RC
RC
RC
R,METAL OXIDE
R,METAL
RC
RC
RC
RC
RC
RC
RC
R,METAL OXIDE
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
5.6K OHM 1/10W
22K OHM 1/4W
2.2K OHM 1/10W
10K OHM 1/10W
0.22 OHM 1W
820K OHM 1/4W
47 OHM 1/2W
470 OHM 1/4W
560 OHM 1/10W
56K OHM 1/2W
10K OHM 1/10W
330 OHM 1/4W
5.6 OHM 2W
2.2K OHM 1/6W
100 OHM 1/10W
68K OHM 1/4W
4.7 OHM 1/4W
1K OHM 1/10W
560 OHM 1/10W
1K OHM 1/4W
100 OHM 1/4W
0.33 OHM 1W
10K OHM 1/4W
680K OHM 1/10W
1K OHM 1/10W
1K OHM 1/4W
470 OHM 1/10W
56K OHM 1/10W
1K OHM 1/4W
220K OHM 1/4W
27K OHM 1/10W
4.7K OHM 1/10W
100 OHM 1/10W
220 OHM 1/4W
100 OHM 1/10W
22K OHM 1/10W
47K OHM 1/10W
1.2K OHM 1/10W
3.3K OHM 1/10W
3.3K OHM 1/10W
3.3K OHM 1/10W
1.5K OHM 1/10W
1.5K OHM 1/10W
1.5K OHM 1/10W
1K OHM 1/10W
10K OHM 1/10W
10K OHM 1/4W
270 OHM 1/4W
560 OHM 1/4W
330K OHM 1/10W
1K OHM 1/10W
75 OHM 1/10W
270 OHM 1/10W
270 OHM 1/10W
270 OHM 1/10W
47K OHM 1/10W
2.2K OHM 1/10W
5.6K OHM 1/10W
27K OHM 1/10W
22K OHM 1/10W
470 OHM 1/10W
2.7K OHM 1/10W
2.2K OHM 1/10W
8.2K OHM 1/10W
560 OHM 1/2W
3.3K OHM 1/10W
10K OHM 1/4W
1K OHM 1/4W
1K OHM 1/4W
1K OHM 1/10W
75 OHM 1/10W
75 OHM 1/4W
820 OHM 1/4W
75 OHM 1/10W
R,METAL
R,METAL
RC
RC
RC
RC
RC
R.METAL OXIDE
RC
RC
R,METAL
RC
RC
RC
RC
8.2K OHM 1/10W
2.2 OHM 1/2W
3.3K OHM 1/6W
1.2K OHM 1/10W
10K OHM 1/10W
47K OHM 1/4W
820 OHM 1/4W
180 OHM 1W
100 OHM 1/4W
4.7 OHM 1W
180K OHM 1/4W
470 OHM 1/2W
68 OHM 1/2W
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
R,METAL OXIDE
RC
R,FUSE
RC
RC
R,FUSE
J2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
RESISTORS
REF. NO. PART NO.
DESCRIPTION
CAPACITORS
R714
R715
R719
R740
R741
R802
R803
R804
R805
R806
R807
R809
R811
R813
R814
R815
R816
R1002
R1003
R1004
R1005
R1009
R1010
R801R7750J
R801R7750J
R801R7104J
R002T4221J
R002T4102J
R002T4272J
R3X18A153J
R002T4272J
R3X18A153J
R002T4272J
R3X18A153J
R801R7122J
R801R7122J
R801R7271J
R801R7122J
R801R7271J
R801R7271J
R801R7123J
R801R7104J
R801R7154J
R002T4683J
R002T4473J
R002T2330J
RC
RC
RC
RC
RC
RC
75 OHM 1/10W
C435
C437
C440
C443
C446
C448
C501
C502
C503
C505
C506
C508
C509
C513
C514
C515
C517
C518
C519
C520
C521
C522
C524
C525
C526
C528
C529
C530
C531
C532
C541
C542
C543
C601
C602
C603
C604
C605
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C617
C618
C619
C620
C622
C623
C624
C625
C629
C630
C631
C632
C634
C701
C703
C704
C711
C740
C744
C745
C746
C803
C804
C805
C806
C819
C1001
C1002
C1003
P235W1104J
P4J7F3394J
P235W1103J
P4N8FJ822H
E5EZU5220M CE
E02LTD100M CE
CD39E0MH3M CC
C0JBB0713K
C0JBB0713K
P2472B104M
E02LU8100M CE
E02LU1101M CE
C0JTB05Q2K CC
CS0RB0414K CC
E50HU2100M CE
E02LT2102M
C03L0R713K
P2472B224M
E02LT2102M
C0J0B05Q2K CC
E62NFB221M CE
E5EZT2102M CE
CMP
CMPP
CMP
0.1 UF 100V MKT
75 OHM 1/10W
100K OHM 1/10W
220 OHM 1/4W
1K OHM 1/4W
2.7K OHM 1/4W
15K OHM 2W
2.7K OHM 1/4W
15K OHM 2W
2.7K OHM 1/4W
15K OHM 2W
1.2K OHM 1/10W
1.2K OHM 1/10W
270 OHM 1/10W
1.2K OHM 1/10W
270 OHM 1/10W
270 OHM 1/10W
12K OHM 1/10W
100K OHM 1/10W
150K OHM 1/10W
68K OHM 1/4W
47K OHM 1/4W
33 OHM 1/2W
0.39 UF 250V PMS
0.01 UF 100V MKT
0.0082UF 1.25KV
22 UF 50V
CMPP
10 UF 250V
R,METAL OXIDE
RC
R,METAL OXIDE
RC
R,METAL OXIDE
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
RC
0.0022UF 250V
0.001 UF 2KV B
0.001 UF 2KV B
0.1 UF 275V PHE840
10 UF 100V
CC
CC
CMP
!
100 UF 10V
470 PF 500V B
0.01 UF 50V B
10 UF 16V
CE
CC
CMP
CE
1000 UF 16V
0.001 UF 2KV R
0.22UF 275V PHE840
1000 UF 16V
470 PF 500V B
220 UF 160V
1000 UF 16V
0.001 UF 2KV R
220 UF 16V
82 UF 400V
470 PF 250V
0.001 UF 250V
0.1 UF 25V B
22 UF 50V
220 PF 50V B
0.022 UF 50V B
47 UF 25V
!
RC
C03L0R713K
CC
E02LU2221M CE
E52D0H820M CE
CD39B0MQ2K CC
CD39E0M13M CC
CS0RB0315K CC
E5EZU5220M CE
CS0RB04H2K CC
CS0RB04H4K CC
E02LU3470M CE
CS0RB02L5K CC
CS0RCH4Q1J CC
E50HU5010M CE
CS0RF0316Z CC
E50HU5010M CE
CS0RB0216K CC
CS0RF0316Z CC
CS0RB0315K CC
CS0RB0315K CC
E02LU2101M CE
E50HU53R3M CE
CS0RB04E3K CC
E02LU1471M CE
CS0RB0216K CC
CS0RB0216K CC
CS0RB04Q3K CC
E50HU2220M CE
CS0RB0315K CC
CS0RB0315K CC
CS0RB0315K CC
CS0RB0315K CC
CS0RB0315K CC
CS0RB0414K CC
CS0RCH4Q1J CC
E50HU2100M CE
CS0RB0315K CC
E02LU5330M CE
E50HU2100M CE
E00NU2470M CE
CS0RB04Q2K CC
CS0RCH4Q2J CC
CS0RB0413K CC
E50HU1101M CE
E50HU2100M CE
E00NU2100M CE
E00NU2100M CE
CS0RB0414K CC
E02LTD010M CE
CS0RB04Q2K CC
CS0RB04Q2K CC
CS0RB04U2K CC
CAPACITORS
C001
C002
C003
C004
C005
C006
C102
C103
C104
C105
C106
C108
C109
C110
C111
C112
C113
C114
C115
C116
C119
C120
C121
C122
C131
C135
C201
C202
C203
C204
C205
C207
C209
C210
C212
C213
C215
C216
C217
C218
C220
C221
C401
C403
C408
C410
C412
C413
C414
C417
C418
C422
C423
CS0RB04H4K CC
E02LU0471M CE
E50HU5010M CE
CS0RCH4Q1J CC
CS0RCH4Q1J CC
0.022 UF 50V B
470 UF 6.3V
1
UF 50V
!
47 PF 50V CH
47 PF 50V CH
100 PF 50V CH
0.1 UF 25V B
22 PF 50V CH
0.0047UF 50V B
0.1 UF 25V B
0.0022UF 50V B
22 PF 50V CH
22 PF 50V CH
0.47 UF 16V B
82 PF 50V CH
0.47 UF 16V B
22 PF 50V CH
0.1 UF 25V B
2200 UF 6.3V
C0JTCH412J
CC
CS0RB0315K CC
CS0RCH4H1J CC
CS0RB04Q3K CC
CS0RB0315K CC
CS0RB04H3K CC
CS0RCH4H1J CC
CS0RCH4H1J CC
CS0RB02Q5K CC
CS0RCH4W1J CC
CS0RB02Q5K CC
CS0RCH4H1J CC
CS0RB0315K CC
0.33 UF 16V B
47 PF 50V CH
1
1
1
1
1
UF 50V
UF 25V F
UF 50V
UF 16V B
UF 25V F
0.1 UF 25V B
0.1 UF 25V B
100 UF 16V
3.3 UF 50V
0.0015UF 50V B
470 UF 10V
E02LF0222M
CE
CS0RB04Q3K CC
CS0RB0315K CC
CS0RB0216K CC
0.0047UF 50V B
0.1 UF 25V B
1
UF 16V B
1
1
UF 16V B
UF 16V B
E02LU0101M
CE
100 UF 6.3V
10 UF 16V
10 UF 16V
E50HU2100M CE
E50HU2100M CE
CS0RCH4U1J CC
CS0RCH430C CC
CS0RB0413K CC
CS0RB0414K CC
CS0RB04H3K CC
CS0RB0413K CC
CS0RB02L5K CC
E50HU2100M CE
E50HU5010M CE
CS0RB0413K CC
CS0RB0216K CC
CS0RB0315K CC
E02LU5220M
E02LU2470M
CS0RB04H4K CC
E02LU1471M CE
CS0RB0315K CC
CHGTB04H2K CC
E02LT4471M
0.0047UF 50V B
22 UF 16 V
68 PF 50V CH
0.1 UF 25V B
0.1 UF 25V B
0.1 UF 25V B
0.1 UF 25V B
0.1 UF 25V B
0.01 UF 50V B
47 PF 50V CH
10 UF 16V
3
PF 50V CH
0.001 UF 50V B
0.01 UF 50V B
0.0022UF 50V B
0.001 UF 50V B
0.33 UF 16V B
10 UF 16V
1
UF 50V
0.001 UF 50V B
UF 16V B
0.1 UF 25V B
33 UF 50V
10 UF 16V
1
0.1 UF 25V B
22 UF 50V
47 UF 16V
0.022 UF 50V B
470 UF 10V
0.1 UF 25V B
220 PF 50V B
470 UF 35V
10 UF 16V
470 UF 35V
0.047 UF 50V MMTV
0.082 UF 50V B
100 UF 35V
47 UF 16 V
CE
CE
470 PF 50V B
470 PF 50V CH
0.001 UF 50V B
100 UF 10 V
10 UF 16V
10 UF 16 V
10 UF 16 V
0.01 UF 50V B
CE
E50HU2100M CE
E02LT4471M
P232T0473J
CE
CMPL
1
UF 250V
470 PF 50V B
470 PF 50V B
680 PF 50V B
0.001 UF 2KV B
470 UF 16V
CS0RB04W4K CC
E02LU4101M
E02LU5100M
E5EZF3222M
P235W1224J
CE
CE
CE
CMP
10 UF 50V
C0JBB0713K
E02LT2471M
E50HU2100M CE
E00NU2220M CE
CC
CE
2200 UF 25V
0.22 UF 100V MKT
2.2 UF 250V
10 UF 16V
22 UF 16 V
E5EZTD2R2M CE
J2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
CAPACITORS
REF. NO. PART NO.
DESCRIPTION
TRANSISTORS
C1004
C1005
C1006
C1007
C1009
CS0RB04W2K CC
820 PF 50V B
Q511
Q512
Q601
Q602
Q603
Q604
Q605
Q801
Q802
Q803
TAAT01281Y
TPAAB05001
T8YJ2412K0
T8YJ2412K0
T8YJ2412K0
TPAAB05001
T8YJ2412K0
TCAT032070
TCAT032070
TCAT032070
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
KTA1281_Y
KRA102SRTK
E50HU5010M CE
CS0RB04Q2K CC
E50HU2100M CE
CS0RB04Q3K CC
1
UF 50V
470 PF 50V B
10 UF 16V
0.0047UF 50V B
2SC2412KT146 R,S
2SC2412KT146 R,S
2SC2412KT146 R,S
KRA102SRTK
2SC2412KT146 R,S
KTC3207-AT
DIODES
D001
D102
D104
D105
D108
D403
D405
D406
D407
D410
D501
D502
D505
D506
D507
D508
D509
D510
D511
D512
D513
D514
D515
D516
D517
D518
D519
D521
D523
D524
D525
D528
D602
D603
D604
D606
D607
D608
D609
D610
D611
D709
D97U03301B
D97U05R11B
D1VT001330
0021E9Q010
D1VT001330
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
LED
MTZJ33B T-77
MTZJ5.1B T-77
1SS133T-77
LTL-1BEFJ
1SS133T-77
11E1-EIC
AU02A-EIC
1SS133T-77
1SS133T-77
AU02A-EIC
GBL06L-6177
MTZJ3.6B T-77
SB290S
1SS133T-77
1SS133T-77
1N4937
11E1-EIC
RU2AM-EIC
1N4937
KTC3207-AT
KTC3207-AT
DIODE,SILICON
COILS & TRANSFORMERS
D2WT011E10 DIODE,SILICON
D2WTAU02A0 DIODE,SILICON
L001
L101
L102
L202
L203
L204
L207
L401
L501
L503
L601
L702
L703
L714
T401
T501
02167F100J
02167F100J
02167F100J
02167F3R3J
COIL
COIL
COIL
COIL
10 UH
10 UH
10 UH
3.3 UH
D1VT001330
D1VT001330
DIODE,SILICON
DIODE,SILICON
D2WTAU02A0 DIODE,SILICON
021LA61R0M COIL
1
UH
D4LZBL06L0
D97U03R61B
DIODE
DIODE,ZENER
021LA6100K
033700005R
021679472K
029T000094
028R140018
02167F100J
021LA6100K
021LA6100K
02167F100J
045009003J
0481290974
COIL
COIL,VIDEO IFT
COIL
COIL,LINE FILTER
COIL,DEGAUSS
COIL
COIL
COIL
COIL
TRANS,HORIZONTAL DRIVE
TRANSFORMER,SWITCHING
JACKS
SOCKET,21PIN
RCA JACK
10 UH
3700005
4.7 MH
0R7A223F24Y
8R140018
10 UH
10 UH
10 UH
!
D2WXB290S0 DIODE,SILICON
D1VT001330
D1VT001330
DIODE,SILICON
DIODE,SILICON
!
!
D2WXN49370 DIODE,SILICON
D2WT011E10 DIODE,SILICON
D2WXRU2AM0 DIODE,SILICON
D2WXN49370 DIODE,SILICON
10 UH
ETH09K14BZ
81290974
D23U1003A3
DIODE,SCHOTTKY
SB10-03A3
SB290S
1SS133T-77
SB10-03A3
SB290S
D2WXB290S0 DIODE,SILICON
!
D1VT001330
D23U1003A3
DIODE,SILICON
DIODE,SCHOTTKY
J701
J702
J703
J801
J1001
063G100042
060G421016
060G421017
066X120014
060J121014
0350_9982_05
HTJ-032-05AY
HTJ-032-05AW
D2WXB290S0 DIODE,SILICON
D2WT011E10 DIODE,SILICON
11E1-EIC
RCA JACK
D1VT001330
D1VT001330
D1VT001330
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
1SS133T-77
1SS133T-77
1SS133T-77
11E1-EIC
SOCKET,CATHODE RAY TUBE HPS3200-010501
JACK,RCA,3.5
SWITCHES
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH,TACT
SWITCH
MSJ-035-12A_PC
D2WT011E10 DIODE,SILICON
D2WT011E10 DIODE,SILICON
SW102 0504201T31
SW104 0504201T31
SW106 0504201T31
SW107 0504201T31
SW501 0530205016
SKHVBED010
SKHVBED010
SKHVBED010
SKHVBED010
SDKVA30100
11E1-EIC
D97U01201B
D97U05R61B
D1VT001330
D1VT001330
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
MTZJ12B T-77
MTZJ5.6B T-77
1SS133T-77
1SS133T-77
11E1-EIC
MTZJ6.8B T-77
MTZJ6.8B T-77
MTZJ6.8B T-77
1SS133T-77
1SS133T-77
1SS133T-77
MTZJ5.1B T-77
!
VARIABLE RESISTORS
D2WT011E10 DIODE,SILICON
VR401
VR420
VR501
V1163H3BTC VOLUME,SEMI FIXED
V1163Q2BTC VOLUME,SEMI FIXED
V1163Q2BTC VOLUME,SEMI FIXED
P.C.BOARD ASSEMBLIES
EVNCYAA03BE3
EVNCYAA03BQ2
EVNCYAA03BQ2
D97U06R81B
D97U06R81B
D97U06R81B
D1VT001330
D1VT001330
D1VT001330
D97U05R11B
DIODE,ZENER
DIODE,ZENER
DIODE,ZENER
DIODE,SILICON
DIODE,SILICON
DIODE,SILICON
DIODE,ZENER
PCB010 A3L804M010K PCB ASS'Y
PCB110 A3L804M110K PCB ASS'Y
TMB537A
TCB396A
MISCELLANEOUS
ANTENNA ROD
CORE,BEADS
CORE,BEADS
CORE,BEADS
CORE,BEADS
BATTERY,MANGAN
BATTERY,MANGAN
CORD AC BUSH
BRAIDED WIRE
ANT001 125C108028
B501
B502
B504
T4-216BP-BK
W4BRH3.5X6X1
W5RH3.5X5X1.0
W5RH3.5X5X1.0
W5RH3.5X5X1.0
R03(AB)2PXGPI
R03(AB)2PXGPI
6655827
024HT03564
024HT03553
024HT03553
024HT03553
1412004013
1412004013
1206655827
1278140030
ICS
IC101
IC102
IC199
IC201
IC401
IC501
IC502
IC503
IC504
IC703
I5PF0F005A
IC7J0311A0
A3L802N015
I0WDE246C0
I0WTD81740
I0WD015070
I1KA97806A
I1KA98R09A
0002E00610
I0QF022330
IC
IC
IC
IC
IC
IC
IC
IC
OECF005A
R3111N311A/C-TR
S-24C04BDP-LA
STV2246C
TDA8174A
TEA1507P/N1
KIA7806API
KIA78R09API
LTV-817M-VB
NJM2233BM-T1
AN7511
B1001
BT001
BT002
CD501
CD801
CD802
CF201
CF202
CF205
CF303
CP101
CP401
CP501
CP502
CP801
!
SM1573-001
WHL6032038 FLAT CABLE AWM2468 AWG26 10C BLACK 320MM
PHOTO COUPLER
IC
1012T5R503
1029238R93
1012T04001
1012T04101
069X160379
069S450089
069S320419
069S420110
069W01001A
FILTER,CERAMIC TRAP
FILTER,SAW
TPS5.5MB-TF21
TSF5330U
MKT40.4MA110P-TF
MKT41.5MA110P
06JQ-ST
A1561WV2-A5P
A3963WV2-3PD
A1561WV2-2P
003P-2100
A2502WV2-2P
B2013H02-10P
B2013H02-10P
IC1001 I01DP75110
IC
FILTER,CERAMIC TRAP
FILTER,CERAMIC TRAP
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
WIRE HOLDER
TRANSISTORS
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
FET
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
TRANSISTOR,SILICON
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
COMPOUND TRANSISTOR
Q102
Q103
Q201
Q202
Q204
Q401
Q402
Q501
Q504
Q505
Q506
Q507
Q508
Q509
Q510
TNAAJ05003
TPAAB05001
T8AA03881S
T8YJ2412K0
T8YJ2412K0
TDUF024990
TC5T01627Y
T410K26470
TA3T016240
TCAT032034
T6YJ1037K0
TCATC31980
TNAAJ05003
TNAAJ05003
TNAAC05002
KRC111SRTK
KRA102SRTK
KTC3881S-RTK
2SC2412KT146 R,S
2SC2412KT146 R,S
2SD2499
2SC1627_Y(TPE2)
2SK2647-01MR
2SA1624-AA
KTC3203_Y-AT
2SA1037AKT146R,S
KTC3198-AT(Y,GR)
KRC111SRTK
!
!
CP1001 069S120419
CP802A 067U010049
CP802B 067U010049
WIRE HOLDER
CUS011 800WFAA008 CUSHION C
EL001
EL002
F501
FB401
FH501
FH502
124116281A
124120301A
080NT04003
043214034F
06710T0006
06710T0006
EYE LET
EYE LET
FUSE
TRANSFORMER,FLYBACK
HOLDER,FUSE
HOLDER,FUSE
XRY16X28BD
XRY20X30BD
50T040HCC
3214034F
EYF-52BC
EYF-52BC
!
KRC111SRTK
KRC103SRTK
J2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
DESCRIPTION
MISCELLANEOUS
OS101
PH001
0773071001
069D01001A
069W01001A
0560V20115
REMOTE RECEIVER
CONNECTOR PCB SIDE
CONNECTOR PCB SIDE
RELAY
RPM7138-H5
003P-2100
003P-2100
or
RY501
ALKS321
SP1001 070C732003
SPEAKER
SA08A05BWB
B59104-J80-A10
RC-FK010
TUWRF4EG-778F2
A34AGT13X98(L)
HC-49/U-S
TH501
TM101
TU001
V801
D8E0J80A10
076N0FK010
0145517006
098P1404B2
100CT4R013
100CT4R408
100CT3R509
DEGAUSS ELEMENT
TRANSMITTER
TUNER,VHF-UHF
CRT W/DY
CRYSTAL
CRYSTAL
!
X101
X601
HC-49/U
HC-49/U
X602
CRYSTAL
RESISTOR
RC................... CARBON RESISTOR
CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|