Telex Network Card IP 223 User Manual

Model IP-223

Remote Adapter Panel

Technical Manual

up to and including version 4.100

803641 Rev K

07/2008

Download from Www.Somanuals.com. All Manuals Search And Download.

Table

Contents

CTCSS (CONTINUOUS TONE CODED SQUELCH SYSTEM)

OVERVIEW..................................................... 13

CONNECTION ............................................................. 29

Tone/Console Operation .......................................29

2-/4-W IRE J UMPER S ETTINGS ..................................... 29

TX S IDE S ETTINGS ..................................................... 29

L OCAL PTT I/O ......................................................... 30

C ROSS M UTE I/O ....................................................... 30

S UPERVISORY I/O ....................................................... 30

Level Adjustments .................................................30

G ENERAL A LIGNMENT ................................................ 31

R ADIO /L INE TX L EVEL ............................................... 31

R ADIO /L INE RX L EVEL ............................................... 31

LINE TX MONITOR LEVEL (TONE AND CONSOLE MODE

ONLY) ......................................................................... 31

CTCSS L EVEL ........................................................... 32

Frequency Decoding .............................................32

Operating Modes ..................................................13

F EATURES ...................................................................14

IP-223 A CCESSORIES ..................................................15

IP-223 Specifications ............................................16

Front Panel ...........................................................16

T EST AND A DJUSTMENT P OINTS ..................................16

H ANDSET J ACK ...........................................................17

IC B UTTON .................................................................17

LCD D ISPLAY .............................................................17

L INE B UTTON .............................................................18

TX LED .....................................................................18

LNK LED ..................................................................18

Back Panel ............................................................19

10/100 E THERNET C ONNECTOR ..................................19

S ERIAL C ONNECTOR ...................................................19

R ADIO 1 AND R ADIO 2 (L INE 1 AND L INE 2)

CONNECTORS ..............................................................20

P OWER C ONNECTION ..................................................20

SETUP INFORMATION ................................ 33

Setting the IP Address Information ......................33

U SING H YPER T ERMINAL ............................................. 34

Accessing IP-223 Web Browser Configuration

Windows ................................................................39

IP-223 Web Setup Windows Standards ................40

L INKS ......................................................................... 40

Welcome Window .................................................42

Basic Ethernet Setup Window ...............................43

S ERIAL N UMBER F IELD .............................................. 43

MAC A DDRESS .......................................................... 43

U SE DHCP S ERVER C HECK B OX ............................... 44

U NIT IP A DDRESS F IELD ............................................ 44

S UBNET M ASK F IELD ................................................. 44

G ATEWAY A DDRESS F IELD ......................................... 44

DNS (D OMAIN N AME S ERVER ) N UMBER 1–3 F IELDS . 44

P ACKET D ELAY BEFORE P LAYBACK F IELD ................. 44

QOS (Q UALITY OF S ERVICE ): P RECEDENCE B ITS

COMMUNICATIONS SYSTEM DESIGN.... 23

Network Requirements ..........................................23

B ANDWIDTH ................................................................23

M ULTICAST .................................................................23

I NTERNET G ROUP M ANAGEMENT P ROTOCOL (IGMP) 24

N ETWORK P ERFORMANCE ...........................................24

INSTALLATION AND LEVEL SETTINGS . 25

Local/Radio Connections .....................................25

J UMPER P OSITIONS .....................................................25

TX A UDIO C ONNECTION .............................................27

RX A UDIO C ONNECTION .............................................27

COR (C ARRIER O PERATED R ELAY ) I/O

(INPUT/OUTPUT) ........................................................28

PTT C ONNECTION ......................................................28

M ONITOR C ONNECTION ..............................................28

R1 AND R2 R ELAYS .....................................................28

D IGITAL I/O ...............................................................29

FIELD ........................................................................ 44

QOS: D, T, AND R (D ELAY , T HROUGHPUT , AND

RELIABILITY) BITS FIELD ............................................ 45

L OCAL C OMPUTER IP A DDRESS 1-10 F IELDS ............ 45

Download from Www.Somanuals.com. All Manuals Search And Download.

S UBMIT B UTTON .........................................................46

General Gain Setup ............................................. 47

H ANDSET M IC G AIN D ROP D OWN M ENU ....................47

H ANDSET S IDETONE G AIN D ROP D OWN M ENU ...........47

R ECEIVE G AIN D ROP D OWN M ENU ............................47

T RANSMIT G AIN D ROP D OWN M ENU ..........................48

CTCSS G AIN D ROP D OWN M ENU ..............................48

TX V OICE G AIN F IELD ...............................................48

S UBMIT B UTTON .........................................................48

Multicast Address Setup Window ........................ 49

L INE N UMBER F IELD ..................................................49

E NABLE VIA E THERNET C HECK B OX ...........................49

L INE T YPE D ROP D OWN M ENU ..................................50

L INE N AME F IELD ......................................................50

RX M CAST A DDRESS F IELD ........................................50

RX P ORT F IELD ..........................................................51

TX G ROUP P ORT F IELD .............................................51

TTL F IELD .................................................................51

V OCODER T YPE D ROP D OWN M ENU ..........................52

E NABLE C HECK B OX ..................................................52

L INE N AME F IELD ......................................................52

M ULTICAST A DDRESS F IELD .......................................52

O UTGOING P ORT F IELD .............................................53

TTL F IELD .................................................................53

E NABLE C HECK B OX ..................................................53

N AME F IELD ...............................................................53

M ULTICAST A DDRESS F IELD .......................................53

I NCOMING P ORT F IELD ..............................................53

O UTGOING P ORT F IELD .............................................53

TTL F IELD .................................................................53

E NABLE C HECK B OX ..................................................53

V OCODER T YPE D ROP D OWN M ENU ..........................54

L INE N AME F IELD ......................................................54

M CAST A DDRESS F IELD ..............................................54

P ORT F IELD ................................................................54

TTL F IELD .................................................................54

S UBMIT B UTTON .........................................................54

Per Line Setup Window ........................................ 55

Per Line Setup Window—

Local, Tone, and Console Mode Configuration .. 56

L INE 1 B UTTON ..........................................................56

L INE 2 B UTTON ..........................................................57

S UBMIT B UTTON .........................................................57

L INE M ODE S TATUS F IELD .........................................57

P ORT E NABLED C HECK B OX .......................................57

A LWAYS O N R ADIO B UTTON .......................................57

O N W ITH PTT R ADIO B UTTON ...................................58

T APE O UTPUT R ADIO B UTTON ....................................58

TX D ELAY F IELD ........................................................58

RX D ELAY F IELD ........................................................58

S QUELCH T AIL D ELAY F IELD ......................................58

J UMP T O E NTRY D ROP D OWN M ENU .........................58

U PDATE B UTTON ........................................................58

T ONE E NABLE C HECK B OX .........................................59

R ELAY D ROP D OWN M ENU .........................................59

R ELAY G ROUP D ROP D OWN M ENU .............................59

R ELAY T IME (MS ) F IELD .............................................59

D IGITAL O UTPUT F IELD - L OCAL M ODE O NLY ...........60

CTCSS F REQ F IELD - L OCAL M ODE O NLY .................60

CTCSS D EFAULT C HECK B OX - L OCAL M ODE O NLY .60

S YSTEM F IELD - L OCAL M ODE ....................................60

C HAN F IELD - L OCAL M ODE .......................................60

LAM L EVEL F IELD .....................................................61

LAM T IME F IELD .......................................................61

O PTIONS .....................................................................62

Supervisor Check Box ........................................... 62

Cross Mute Check Box .......................................... 62

Full Duplex Check Box ......................................... 62

RxAGC Check Box................................................ 62

Hi-Pass RX Check Box.......................................... 62

Pre-Emphasize TX Check Box .............................. 62

TX Monitor Check Box ......................................... 62

2-Wire Check Box ................................................. 63

Parallel Console Check Box .................................. 63

PTT Notch Filter Check Box ................................. 63

PTT T IMEOUT F IELD ..................................................63

Serial Port Mode Drop Down Men u ...................... 63

Serial Port Params Drop Down Menu ................... 64

FleetSync Decode Check Box

(Tone and Local Modes)........................................ 65

FleetSync Encode Check Box (Local Mode Only) 66

MDC Decode Check Box

(Tone and Local Modes)........................................ 66

MDC Encode Check Box....................................... 66

Tone Type Drop Down Menu................................ 66

ANI Suffix Field .................................................... 67

Digit Duration Fiel d ............................................... 67

Interdigit Duration Field ........................................ 67

Pause Duration Field.............................................. 67

Preamble Duration Fiel d ........................................ 67

Group Digit Fiel d ................................................... 67

Repeat Digit Fiel d .................................................. 67

ANI Decoder # Field.............................................. 67

ANI Call Type Drop Down Menu ......................... 68

ANI Call Format Fiel d ........................................... 68

Per Line Setup Window—

Phone Mode Configuration ................................. 69

Auto Answer Fiel d ................................................. 69

Auto Disconnect Time Fiel d .................................. 69

TX D ELAY F IELD ........................................................69

RX D ELAY F IELD ........................................................70

LAM L EVEL F IELD .....................................................70

LAM T IME F IELD .......................................................70

Mic Click Call Enabled Check Box....................... 70

Number of Clicks Field.......................................... 70

Time Between Clicks Field.................................... 70

Click Dial String Fiel d ........................................... 70

Click Dial Timeout Field ....................................... 71

Relay Closure......................................................... 71

R1 - Ring Check Bo x .......................................... 71

Download from Www.Somanuals.com. All Manuals Search And Download.

R2 - OffHook Check Box ................................... 72

Rx AGC Enabled Check Box ................................ 72

Keep Alive Digits Enabled Check Box ................. 72

Star/Pound Keying Enabled Check Bo x ................ 72

Detect Tones Enabled Check Box ......................... 72

Hook Flash Time Field .......................................... 72

Network Call Timeout Field .................................. 72

Station ID Field...................................................... 72

Busy Channel Lockout Check Box........................ 72

C550 Operation Enabled Check Bo x ..................... 73

RP251 Operation Enabled Check Box................... 73

RP251 Access Digits Field .................................... 73

RP251 Connect Digits Field .................................. 73

S ERIAL P ORT M ODE D ROP D OWN M ENU ....................73

S ERIAL P ORT P ARAMETERS D ROP D OWN M ENU ..........73

FleetSync Decode Check Box ............................... 75

MDC Decode Check Box ...................................... 75

Tone Type Drop Down Menu................................ 75

ANI Suffix Field .................................................... 75

Digit Duration Fiel d ............................................... 75

Interdigit Duration Field ........................................ 76

Pause Duration Field.............................................. 76

Preamble Duration Fiel d ........................................ 76

Group Digit Fiel d ................................................... 76

Repeat Digit Fiel d .................................................. 76

ANI Decoder Field................................................. 76

ANI Call Type Drop Down Menu ......................... 76

ANI Call Format Fiel d ........................................... 77

Per Line Setup Window—

iDEN Radio Configuration ...................................77

TX D ELAY F IELD ........................................................78

RX D ELAY F IELD ........................................................78

S QUELCH T AIL D ELAY F IELD ......................................78

THE RANGE FOR THIS FIELD IS 0 TO 5000. ..................79

J UMP T O E NTRY D ROP D OWN M ENU ..........................79

U PDATE B UTTON ........................................................79

T ONE E NABLE C HECK B OX .........................................79

R ELAY D ROP D OWN M ENU .........................................80

R ELAY G ROUP D ROP D OWN M ENU .............................80

R ELAY T IME (MS ) F IELD .............................................80

C ALL T YPE D ROP D OWN M ENU ..................................81

I DEN N UMBER F IELD .................................................81

LAM L EVEL F IELD .....................................................82

LAM T IME F IELD .......................................................82

Full Duplex Check Box ......................................... 82

RxAGC Check Box................................................ 82

Hi-Pass RX Check Box.......................................... 82

Pre-Emphasize TX Check Box .............................. 82

F1 Last Call Check Box (iDEN Mode only) ......... 83

PTT Notch Filter Check Box ................................. 83

Busy Channel Lockout Check Box........................ 83

PTT T IMEOUT F IELD ..................................................83

S ERIAL P ORT M ODE D ROP D OWN M ENU ....................83

S ERIAL P ORT P ARAMETERS D ROP D OWN M ENU ..........83

Per line Setup Window—

Tetra Radio Configuration .................................. 84

J UMP T O E NTRY D ROP D OWN M ENU ......................... 84

U PDATE B UTTON ....................................................... 84

T ONE E NABLE C HECK B OX ........................................ 84

R ELAY D ROP D OWN M ENU ........................................ 85

R ELAY G ROUP D ROP D OWN M ENU ............................ 85

R ELAY T IME (MS ) F IELD ............................................. 85

T YPE D ROP D OWN M ENU .......................................... 85

ISSI/GSSI N UMBER F IELD ......................................... 86

TX D ELAY F IELD ....................................................... 87

RX D ELAY F IELD ....................................................... 87

LAM L EVEL F IELD ..................................................... 88

LAM T IME F IELD ....................................................... 88

Full Duplex Check Box......................................... 88

RxAGC Check Bo x ............................................... 88

Hi-Pass RX Check Bo x ......................................... 88

Pre-Emphasize TX Check Box ............................. 89

PTT Notch Filter Check Box ................................ 89

Busy Channel Lockout Check Bo x ....................... 89

PTT T IMEOUT F IELD ................................................. 89

S ERIAL P ORT M ODE D ROP D OWN M ENU ................... 89

S ERIAL P ORT P ARAMETERS D ROP D OWN M ENU ......... 89

Save to EEPROM Window ................................... 90

S AVE P ARAMETERS B UTTON ....................................... 90

R ESET IP-223 B UTTON .............................................. 90

Account Setup Window ........................................ 91

Admin System Account ........................................ 91

User System Accoun t ............................................ 91

Enable Check Bo x ................................................. 92

Username Display Column ................................... 92

Password Field ...................................................... 92

New Password Field.............................................. 92

Confirm Password Field........................................ 93

Edit Button ............................................................ 93

Save Button ........................................................... 93

Submit Button ....................................................... 93

Delete, Username, Password, New Password,

Confirm Password Display Columns.................... 93

Delete Button......................................................... 94

Add New User Butto n ........................................... 94

Reset System Parameters Button........................... 94

Edit System Accounts Window ............................. 94

Add New User Window ........................................ 96

Username Field ..................................................... 96

Password Field ...................................................... 96

Confirm Password Field........................................ 96

Additional Feature Check Bo x .............................. 97

Save To EEPROM Check Box.............................. 97

Welcome Page Check Bo x .................................... 97

Account Setup Check Box .................................... 97

Basic Ethernet & Multicast Setup Check Box ...... 97

Clone Console & Pass Change Check Bo x ........... 97

CRP Setup & PIN Table Check Box..................... 97

Download from Www.Somanuals.com. All Manuals Search And Download.

General Gain Check Bo x ....................................... 97

Per Line Setup Check Box..................................... 97

Tone Freq & Durations Check Bo x ....................... 98

Submit Butto n ........................................................ 98

Cancel Button ........................................................ 98

Edit Created Accounts Window ........................... 99

Additional Feature Setup Window ..................... 100

Clone Console Window ...................................... 101

Crosspatch Setup Window ................................. 102

Enable Line – Line Check Box............................ 103

Start Patch FTone Drop Down Menu .................. 103

Stop Patch FTone Drop Down Menu .................. 103

RCP Enable Check Box....................................... 103

Dialing Digits Field ............................................. 103

Interdigit Time Field............................................ 103

Beep Dly Fiel d ..................................................... 103

Patch Timeout Field............................................. 104

Global Field ......................................................... 104

Drop All Field...................................................... 104

RCP T ABLES .............................................................104

J UMP T O E NTRY D ROP D OWN M ENU AND

H OLD T ONE H ANGTIME F IELD ..................................113

F UNCTION T ONE D URATION F IELD ...........................114

F UNCTION T ONE M AGNITUDE F IELD ........................114

FT ONE 1-16 F REQUENCY F IELDS .............................114

UPDATE FIRMWARE ................................. 117

Update Firmware ............................................... 117

I NSTALL TSM ............................................................117

D OWNLOAD T ELEX F IRMWARE ..................................119

U PDATE F IRMWARE T OOL W INDOW ..........................120

File Field .............................................................. 120

Device Type Field................................................ 120

Firmware Version Field ....................................... 120

Left Navigation Pane ........................................... 120

Manual Entry Field .............................................. 121

Username Field .................................................... 121

Password Fiel d ..................................................... 121

Write Firmware Butto n ........................................ 121

Close Button......................................................... 121

U PLOAD V O IP H ARDWARE F IRMWARE ......................121

GO BUTTON ..............................................................104

Entry Field ........................................................... 104

Add String Field .................................................. 104

Delete String Fiel d ............................................... 105

Mode Drop Down Menu...................................... 105

Phone Field (DIAL option only).......................... 105

#1 or #2 Drop Down Menu

(XPATCH option only) ....................................... 105

IP Address Field (XPATCH option only) ........... 106

Rx Multicast Field (DLVOIP option only).......... 106

Rx Port Field (DLVOIP option only) .................. 106

Tx Multicast Field (DLVOIP option only ).......... 106

Tx Port Field (DLVOIP option only) .................. 106

C OMMAND B UTTONS ................................................106

Prev 10 Button ..................................................... 106

Next 10 Button..................................................... 107

CRP PIN Table Window .................................... 108

J UMP T O E NTRY D ROP D OWN M ENU AND

IP-223 SETTINGS - QUICK REFERENCE 123

I/O Connectors ................................................... 123

Adjustments ........................................................ 123

Jumper Settings .................................................. 124

PCB 750743 OR PCB 750630 REVISION F ...............124

PCB 750743 OR PCB 750630 REVISION

C, D, E, AND F ........................................................ 124

PCB 750630 REVISION A ......................................... 124

Jumper Locations ............................................... 125

Additional Resources ......................................... 127

CTCSS Tone Frequency Table ........................... 131

Digital Output Table .......................................... 133

Tone Frequency Table ....................................... 135

GO BUTTON ..............................................................109

S UBMIT B UTTON .......................................................109

PIN E NABLE C HECK B OX .........................................109

E NTRY F IELD ............................................................109

PIN F IELD ................................................................109

S UBMIT B UTTON .......................................................109

Prev 30 Entries Button......................................... 110

Next 30 Entries Button ........................................ 110

Pass Change Window ........................................ 111

Tone Frequency & Durations Window .............. 112

M ONITOR F REQUENCY F IELD ...................................112

PTT F REQUENCY D ROP D OWN M ENU ......................113

G UARD T ONE D URATION F IELD ................................113

G UARD T ONE M AGNITUDE F IELD .............................113

H OLD T ONE M AGNITUDE F IELD ...............................113

Download from Www.Somanuals.com. All Manuals Search And Download.

List

Figures

FIGURE 1. Local and Tone Mode Connections .................................................................................................13

FIGURE 2. Console Mode Connection ...............................................................................................................14

FIGURE 3. IP-223 Front Panel ..........................................................................................................................16

FIGURE 4. IP-223 Case Top Test Points ...........................................................................................................17

FIGURE 5. IP-223 Back Panel ...........................................................................................................................19

FIGURE 6. DB25 Connector Pinout Configuration ...........................................................................................21

FIGURE 7. Jumper Positions ..............................................................................................................................25

FIGURE 8. IP-223 PCB Assembly ......................................................................................................................26

FIGURE 9. HyperTerminal Navigation ..............................................................................................................34

FIGURE 10. Com Terminal Setup Windows .......................................................................................................35

FIGURE 11. HyperTerminal Window Password ................................................................................................36

FIGURE 12. HyperTerminal Factory Setup Options – Serial Port Access Window ..........................................37

FIGURE 13. Connect to [IP Address] Window ..................................................................................................39

FIGURE 14. IP-223 Links ...................................................................................................................................40

FIGURE 15. Welcome Window ...........................................................................................................................42

FIGURE 16. Basic Ethernet Setup Window ........................................................................................................43

FIGURE 17. General Gain Setup Window ..........................................................................................................47

FIGURE 18. Multicast Address Setup..................................................................................................................49

FIGURE 19. Line Type Drop Down Menu ..........................................................................................................50

FIGURE 20. Vocoder Type Drop Down Menu ...................................................................................................52

FIGURE 21. Vocoder Type Drop Down Menu ...................................................................................................54

FIGURE 22. Per Line Setup - Local, Tone, and Console Modes (view 1) ..........................................................56

FIGURE 23. Relay Drop Down Menu—Per Line Setup .....................................................................................59

FIGURE 24. Per Line Setup - Local Tone and Console Modes (view 2) ............................................................61

FIGURE 25. Serial Port Drop Down Menu - Local Mode .................................................................................64

FIGURE 26. Serial Port Params Drop Down Menu - Normal Mode .................................................................64

FIGURE 27. Per Line Setup - Local, Tone, and Console Mode (view 3) ...........................................................65

FIGURE 28. Tone Type Drop Down Menu .........................................................................................................66

FIGURE 29. ANI Call Type Drop Down Menu-Per Line Setup .........................................................................68

FIGURE 30. Per Line Setup - Phone Mode (view 1) ..........................................................................................69

FIGURE 31. Per Line Setup - Phone Mode (view 2) ..........................................................................................71

FIGURE 32. Serial Port Params Drop Down Menu - Phone Mode ...................................................................74

FIGURE 33. Per Line Setup - Phone Mode (view 3) ..........................................................................................74

FIGURE 34. Tone Type Drop Down Menu .........................................................................................................75

FIGURE 35. ANI Call Type Drop Down Menu ..................................................................................................77

FIGURE 36. Per Line Setup - iDEN Radio Mode (view 1) .................................................................................78

FIGURE 37. Relay Drop Down Menu-Per Line Setup .......................................................................................80

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE 38. Call Type Drop Down Menu - iDEN Mode ................................................................................... 81

FIGURE 39. Per Line Setup - iDEN Mode (view 2) ........................................................................................... 81

FIGURE 40. Per Line Setup - Tetra Mode (view 1) ........................................................................................... 84

FIGURE 41. Relay Drop Down Menu ................................................................................................................ 85

FIGURE 42. Type Drop Down Menu - Tetra Mode ........................................................................................... 86

FIGURE 43. Per lIne Setup - Tetra Mode (view 2) ............................................................................................ 87

FIGURE 44. Save to EEPROM .......................................................................................................................... 90

FIGURE 45. Reset IP-223 .................................................................................................................................. 91

FIGURE 46. Account Setup ................................................................................................................................ 92

FIGURE 47. Edit System Account ...................................................................................................................... 94

FIGURE 48. Success Message ............................................................................................................................ 95

FIGURE 49. Add New User—Account Setup ..................................................................................................... 96

FIGURE 50. Edit Created Account—Account Setup .......................................................................................... 99

FIGURE 51. Additional Feature Access ........................................................................................................... 100

FIGURE 52. Clone System Parameters ............................................................................................................ 101

FIGURE 53. Crosspatch Setup ......................................................................................................................... 102

FIGURE 54. Crosspatch Setup - Mode Drop Down Menu .............................................................................. 105

FIGURE 55. #1 or #2 Drop Down Menu-Crosspatch Setup ............................................................................ 106

FIGURE 56. Remote Crosspatch Pin ............................................................................................................... 108

FIGURE 57. Account Password Change .......................................................................................................... 111

FIGURE 58. Tone Frequency and Durations ................................................................................................... 112

FIGURE 59. PTT Frequency Drop Down Menu .............................................................................................. 113

FIGURE 60. Select Installation Folder ............................................................................................................ 118

FIGURE 61. Confirm Installation .................................................................................................................... 118

FIGURE 62. Telex Website Firmware Downloads. .......................................................................................... 119

FIGURE 63. Firmware Update Tool ................................................................................................................ 120

FIGURE 64. Firmware Update Tool— Success Messages .............................................................................. 122

FIGURE 65. Jumper Locations ........................................................................................................................ 125

Download from Www.Somanuals.com. All Manuals Search And Download.

List

Tables

Table 66. IP-223 Specifications ...........................................................................................................................16

Table 67. Jumper Position ...................................................................................................................................19

T a ble 68. DB9 Pinout ..........................................................................................................................................20

Table 69. DB25 Connector Pinout Connections ..................................................................................................21

T a ble 70. IP-2002 Links .......................................................................................................................................40

T a ble 71. D, T, R Binary Reference .....................................................................................................................45

T a ble 72. Standard Function Tone Frequencies ................................................................................................114

Table 73. CTCSS Tone Frequencies ..................................................................................................................131

T a ble 74. Digital Output Values ........................................................................................................................133

Table 75. Supported Radio Dispatch Tone Frequencies ...................................................................................135

Download from Www.Somanuals.com. All Manuals Search And Download.

CHAPTER 1

Overview

The IP-223 Remote Adapter Panel provides a reliable means of remotely controlling two (2) audio devices. The adapter has

multiple modes allowing it to connect to both digital and analog consoles, and performs a variety of other tasks related to

putting radios on a digital network.

The IP-223 is interconnected to the distant remote control console(s) by means of any available WAN (Wide Area Network) or

LAN (Local Area Network) connection.

Operating Modes

The IP-223 is capable of operating each audio port in different modes:

Local Mode – The radio is connected directly to the IP-223 allowing for simple migration and local control of the radio.

Tone Mode – The IP-223, based on Ethernet traffic, generates the keytones required to control standard industry tone-

equipped radio circuits. This allows an existing tone decoder and radio to be connected. This mode also supports a parallel

analog console.

FIGURE 76. Local and Tone Mode Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

Console Mode – Allows the use of existing tone-based consoles. The IP-223 decodes industry standard tones, converts it

to Ethernet traffic to another IP-223 that can be in tone or local mode.

FIGURE 77. Console Mode Connection

Phone Mode –

Using a PIB (Phone Interface Box) or TDI (Telephone Dispatch Interface), a line on the IP-

223 is used to connect to an analog phone line.

iDen Radio Mode –

TETRA Radio Mode –

Using the NI-223, allows interface with a Falcon Class PTT (Push-To-Talk) mobile phone

system.

Used to interface to a TETRA digital trunked system using the IP-223 and the Sepura

SRM2000 mobile radio. The IP-223 interfaces the radio through the PEI (Peripheral

Equipment Interface) allowing dispatch access to TETRA radio assets.

Features

NOTE:

The features listed below for the IP-223 version 4.100 do not comprise the full feature set. For more information

on all the features available, contact Radio Dispatch Sales listed on www.telex.com

•

Ethernet TX and LINK LEDs

•

RX (Receive) audio squelch

PTT, Monitor, F1 and F2 relays (programmable to any • Crosspatch capability

function tone or revert to F1)

• ANI (Automatic Number Identification) over-the-air-

•

Four (4) PTT modes and three (3) monitor modes

Nine (9) selectable PTT frequencies

protocol—decode and display

• Provides iDEN interface

Seven (7) digital outputs for channel selection,

completely programmable per function tone

• Supports Sepura SRM2000, TETRA radio

• E.F. Johnson RS5300 P25 radio interface

• Remote Crosspatch capabilities

• POTS line fail-over

•

CTCSS (Continuous Tone Coded Squelch System)

generation (64 frequencies)

•

Hardware and software gain control

• Phone line interface

Local handset port for monitoring activity and

transmission back to base or to radio

• MDC and Fleetsync Decode

• 5/6 Tone signalling encode/decode

• Kenwood radios interface

•

RS-232C port on rear for initial configuration and

direct radio control

Single function tone recognition (16 function tones)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Modes

NOTE:

Transient protection is provided near all audio inputs and outputs. The IP-223 line transformers are not designed

to operate on lines carrying DC (direct current). If a voltage is on the line, isolate with external capacitors. If the

line termination must conduct direct current, install a 600:600 Ohm transformer designed for the current

involved.

IP-223 Accessories

There are several optional accessories available for the IP-223:

Part Number

223RACK

2490248

Description

1 unit high rack shelf to hold up to two (2) IP-223 units

Alignment Handset

730153

Power Supply

301611000

301611004

301611001

301912000

PRD000003000

301953000

301956000

301957000

301969000

301961000

879794

Fleetsync Over the Air Decode

FleetSync Encode/Decode

MDC Over the Air Decode

NI-223

IP223 to EFJohnson 5300 Mobile Radio Advanced Control Interface Box

IP223DB9Splitter - Serial Port splitter cable DB9

IP223CAB150/180 - IP223-Kenwood TK-150/180 cable

IP223CAB90 - IP223-Kenwood TK-90 cable

IP223CABCDM1250 - IP-223-Motorola CDM and GM cable

IP223CAB2000 - IP-223-Sepura SRM2000 cable

IP223CAB Tone - IP-223-Dual DB25 Tone cable 24ft.

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

IP-223 Specifications

The specifications for the IP-223 are listed in Table 1. The specifications are subject to change without notice.

CAUTION: This device is NOT PoE (Power Over Ethernet) compatible.

TABLE 1. IP-223 Specifications

Operating Temperature Range 0 to 70°C for full specifications

Power Requirements +12 to +16Vdc, semi-regulated, ~700mA

Ethernet Speed 10 BaseT or 100 BaseTX

Lease Lines 2W and 4W supported

Radio Interface ±45VDC withstand rating

Relay Contact Ratings 1A at 125Vac

Non-Relay Outputs Open collector, active low, 200mA maximum, 40V collector to emitter voltage

Radio Input Level 10mVpp to 10Vpp, adjustable

Radio Output Level 10mVpp to 10Vpp for mic level or -40 to +10dBm into 600Ω load, adjustable

Radio Output Impedance 600Ω for balanced mode, 200Ω for single ended mode

Frequency Response ±1.5dB, 300 to 3000Hz

Audio Distortion 2% THD maximum

DTMF Detection Bandwidth ± 25 Hz around center of frequency

MON timer 10ms to 9999ms, adjustable

Dimensions 8 ½” (215.9mm) Wide, 9 3/4” (247.65mm) Deep, by 1 5/8” (41.275mm) High

Actual Weight 3.75lb (1.701kg)

Shipping Weight and Dimensions 5lbs (2.267kg) ~ 12”(304.8mm) x 10”(254mm) x3”(76.2mm)

Front Panel

TX LED

LNK LED

Handset

jack

Line button

Test and

adjustment points

IC button LCD display

FIGURE 78. IP-223 Front Panel

Test and Adjustment Points

Test and adjustment points for Radio 1 and Radio 2 are provided on the front panel. Newer versions of the IP-223 provide

access to additional test and adjustment points on the case top, as shown in Figure 79.

Download from Www.Somanuals.com. All Manuals Search And Download.

Front Panel

NOTE:

Radio 1 and radio 2 are also referred to as line 1 and line 2 in this manual.

FIGURE 79. IP-223 Case Top Test Points

Handset Jack

An optional handset is available for the IP-223. When the optional handset is plugged into the handset jack, the ability to

monitor and talk on either line is available. The handset jack is located on the front of the unit, see Figure 78. When the

handset PTT switch is pressed, the selected radio connected to the IP-223 is keyed up on the existing frequency and the

handset microphone audio is transmitted.

Ethernet audio is also generated on the TX multicast and port for the selected line. This functionality can be used to test both

the Ethernet network and the analog connection.

IC Button

The IC button, when pressed, sends audio from the handset microphone back through the IP Network on the selected TX

multicast and port. It also sends audio to the transmit lines of the IP-223 without keying up the radio. This means no PTT relay

in local mode and no EIA (Electronic Industries Association) tones in tone mode.

NOTE:

A handset is required to use the IC button.

LCD Display

The LCD display provides panel status information, such as the IP and subnet addresses, line status, and handset line selection.

•

TX F# (# is the selected function tone) indicates a PTT is active.

RX F# (# is the selected function tone) indicates the RX radio is active.

ID # displays when a Fleetsync or MDC ANI ID is decoded. This does not include serial decoding.

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

•

When connected to a serially controlled radio, iDEN, Sepura, Kenwood or Johnson displays.

INTCOM displays when the front panel IC button is pressed.

EnetIC displays when the console generated intercom is received.

CTX F# displays when the console mode IP-223 decodes tones from a tone console in Console mode.

CRX F# displays when the IP-223 transmits wire-line audio to a legacy tone console in Console mode.

PTX F# displays when the IP-223 decodes tones from a legacy tone console attached in parallel in Tone mode.

CPT F# displays when the IP-223 transmits to a line if the line-to-line crosspatch is enabled.

Ring displays when there is an incoming phone call in Phone mode.

Offhook displays when the line is in use during a phone call.

LLM displays when no phone line is connected to the PIB or TDI in Phone mode.

NO LINE ENABLED displays after power-up if neither line is enabled.

Scan List.... displays during power up while the IP-223 is communicating with serial controlled radios that

support the Scan List feature.

To toggle the LCD display, do the following:

1. Press and hold the line button and then momentarily press the IC button.

Three different displays are available with each press of the IC button:

•

While pressing the line button, press the IC button once.

The IP Address and Mask Address of the unit displays.

Continue to hold the line button, then press the IC button a second time.

The TX alignment tones are turned ON.

Continue to hold the line button, then press the IC button a third time.

The RX VU meter displays.

2. Press the IC button a fourth time to clear the display and return to the normal LCD display.

3. Release the line button.

Line Button

The Line button is used to select which radio, or line, the handset audio is routed and which line is being monitored. The

handset line selection is displayed as an asterisk (*) in the right most column of the LCD display. An asterisk (*) on the top

line of the display indicates a connection to line 1, and an asterisk (*) on the bottom line of the display indicates a connection

to line 2.

TX LED

The TX LED provides a visual indication the IP-223 is generating IP packets. When the LED is illuminated, packets are being

transmitted to the network.

LNK LED

The LNK LED provides a visual indication of the Ethernet connection. When the LED is illuminated, a valid network

connection is established.

Download from Www.Somanuals.com. All Manuals Search And Download.

Back Panel

10/100

Ethernet connector

connector (DB9)

FIGURE 80. IP-223 Back Panel

Serial

Power

connection

Radio 1 and radio 2

connectors (DB25)

10/100 Ethernet Connector

The 10/100 Ethernet connector provides the LAN or WAN connection for the IP-223.

Serial Connector

The serial connector (DB9) is used for either of the following:

•

To program an initial IP Address into the IP-223 unit, if the IP Address cannot be programmed through the

Ethernet port on the installed system.

NOTE:

To communicate with HyperTerminal, the jumper setting must be RS-232.

•

To provide serial communication to various radios. Both radio (or line) 1 and radio (or line) 2 are supported on

this connector, with the appropriate splitter cable.

You must adjust the position of the jumper, on J35 when using line 1, or on J26 when using line 2, according to

the serial connection type for the radio interface shown below. See “Jumper Positions” on page 25 for more

information.

Jumper position

Connection type

RS-232

TTL

TABLE 2. Jumper Position

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

SERIAL DB9 PINOUT

SIGNAL

TX 232

LINE #

DB9 PIN #

RX 232

TX TTL

RX TTL

Ground

TX 232

RX 232

TX TTL

RX TTL

both

TABLE 3. DB9 Pinout

Radio 1 and Radio 2 (Line 1 and Line 2) Connectors

Two (2) DB25 connectors are provided for connection to various audio devices. The pinouts shown in Table 4 are used when

custom cables need to be fabricated.

Power Connection

The IP-223 requires +12 to +16VDC, ~700mA of clean power. A 3-pin screw terminal receptacle is provided on the right rear

of the unit, pin 1 is the positive terminal, pin 2 is the ground terminal, and pin 3 is the earth ground terminal.

As with all communication equipment earth ground should be used. Earth ground is a low impedance path to earth for the

purpose of discharging lightening, static, and radiated energy.

Download from Www.Somanuals.com. All Manuals Search And Download.

Back Panel

FIGURE 81. DB25 Connector Pinout Configuration

TABLE 4. DB25 Connector Pinout Connections

Pin #

Signal

Cable color

Brown

PTT Relay N.C.

PTT Relay Common

MON Relay N.O.

R1 Relay N.C.

Red

Orange

Pink

R1 Relay Common

R2 Relay N.O.

Yellow

Green

Ground

Lt. Green

Blue

Digital 0/X-Mute

Digital 2

Violet

Shield

Digital 4

Gray

CTCSS

White

Radio RX- in / 4-wire RX

Radio TX- out / 4-wire TX or 2-wire

PTT Relay N.O.

MON Relay N.C.

MON Relay Common

R1 Relay N.O.

Black

Brown/White

Red/White

Red/Black

Orange/White

Orange/Black

Pink/Black

Yellow/Black

Green/White

Green/Black

Blue/White

Violet/White

Gray/Black

R2 Relay N.C.

R2 Relay Common

Digital 6/COR

Digital 1/Supervisory

Digital 3

Digital 5/Local PTT

Radio RX+ input / 4-wire RX

Radio TX+ out / 4-wire TX or 2-wire Black/White

Ground

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

Download from Www.Somanuals.com. All Manuals Search And Download.

CHAPTER 2

Communications System Design

Designing an IP-223 system requires an understanding of the radio network and how the various radios and communication

equipment are connected.

The first step in designing an IP-223 system is to create a roadmap of the radio, console, and any other communication

equipment locations. This roadmap must include the following:

•

Multicast addresses for each channel of TX (transmit) and RX (receive) communication.

Port numbers for each channel of TX and RX communication.

Base IP Addresses assigned to each console and IP-223 on the network.

Network Requirements

Bandwidth

Each VoIP channel requires 50kBit of bandwidth while active. Full-duplex conversation (audio in each direction) requires

100kBit of bandwidth.

NOTE:

Most radio voice communications are half-duplex (only in one direction at any one time), thus requiring 50kbits.

Some radio systems transmit go-ahead beeps when it is clear to talk. In order for the console operator to hear the beeps, the

system must support full-duplex communication. Full-duplex bandwidth may only be required for the first few seconds of a

conversation, due to the brief nature of the go-ahead beeps at the beginning of the transmission.

When using a PIB, TDI, C-6200, or the NI-223 for a telephone connection, 100kBit is required since it is a constant, full-

duplex conversation.

Multicast

In general, Telex systems require multicast to function. The network must be able to support the multicast traffic generated by

the system.

It is very common for networks to enable multicast after an IGMP (Internet Group Management Protocol) join message is sent

out, and then prune off branches after a period of time. Due to the intermittent usage patterns of two-way radios, such a system

can appear to work flawlessly for a period of time, then no longer work.

Download from Www.Somanuals.com. All Manuals Search And Download.

Communications System Design

NOTE:

When using Cisco technology, IP PIM dense mode is generally recommended. Generally speaking, sparse-

dense-mode can also be implemented effectively. We recommend explicitly joining the multicast group with an

IP IGMP static-join X.X.X.X command. For more information on Cisco and IGMP, visit www.cisco.com

Internet Group Management Protocol (IGMP)

IGMP can be used to control where multicast is allowed to propagate. When a console on the subnet is expected to be

continually operational, multicast must be active for that subnet at all times.

Network Performance

Networks should perform well under any loading conditions. The default audio delay is 120ms, plus any delay added by the

network. While delay alone does not cause issues, variable delay (jitter) does. Jitter in a network cannot exceed the

maximum packet buffer of any individual product buffer. Refer to the individual product manuals for these specifications. For

example, the IP-223 can handle approximately 600ms of network jitter.

NOTE:

Losing more than 5% of the total packets transmitted compromises audio quality and system performance.

Optimally, packet loss should be less than 1%.

Download from Www.Somanuals.com. All Manuals Search And Download.

CHAPTER 3

Installation and Level Settings

Local/Radio Connections

NOTE:

Connections to radios differ from connections for remote operation; therefore connections are discussed

separately.

Jumper Positions

An example of the jumper positions are shown in Figure 82. In the figure, jumper 14 (J14) is shown in position A, jumper 3

(J3) is shown in position B, and jumper 23 (J23) has been placed on the center pin indicating the jumper is in the NULL

position.

FIGURE 82. Jumper Positions

To adjust the position of a jumper, do the following:

1. Remove power from the IP-223 unit.

CAUTION: Failure to remove power may cause damage to the IP-223.

2. Remove the six (6) screws from the case top.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Level Settings

3. Carefully slide the case top forward past the IC and LINE buttons, and then lift up to gain access to the PCB (Printed

Circuit Board) as shown in Figure 83.

Case top

PCB assembly

FIGURE 83. IP-223 PCB Assembly

4. Locate the desired jumper on the PCB assembly and use needle nose pliers to adjust the jumper, if necessary.

5. Carefully lift up the case top and place it into position on the chassis bottom.

6. Secure the case top into position using the six (6) screws.

7. Connect power to the IP-223 unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Local/Radio Connections

TX Audio Connection

The IP-223 has a number of options when connecting to the radio. Different jumper settings are required for different

revisions of the PCB installed in the IP-223 unit, and are noted below. Set the jumper position listed for the line according to

the connection type shown below.

If the radio transmit audio output is balanced,

•

connect to pins 13 and 25 of the DB25 connector.

If the transmit audio is single ended,

use pin 25 of the DB25 connector.

•

NOTE:

Shielded cable is recommended.

PCB 750743 or PCB 750630 revision C and higher

Line 1 jumpers: J3, J9, and J11

Line 2 jumpers: J25, J28, and J29

Jumper Position Connection Type

Single Ended Low-Impedence

Balanced 600 ohm

RX Audio Connection

To connect the radio receiver audio to the IP-223, different jumper settings are required for different revisions of the PCB

installed in the IP-223 unit, and are noted below. Set the jumper position for the line according to the connection type shown

below.

•

If the radio receiver audio output is balanced, connect to pins 12 and 24 of the DB25 connector.

If the receiver audio is single ended, use pin 24 of the DB25 connector. The audio source must be after the

squelch circuit to prevent sending continuous noise to the remote console.

•

If a high-impedance point in the receiver is used, a shielded cable is recommended.

PCB 750743 or PCB 750630 revision C and higher

Line 1 jumpers: J16 and J21

Line 2 jumpers: J19 and J20

Jumper Position Connection Type

Single Ended Low-Impedence

Balanced 600 ohm

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Level Settings

Jumper Position

Line 1 Line 2

J14 J24

Receive Input Impedance:

8 ohms (for a speaker input)

600 ohm

10k ohm

NULL

NOTE:

When the speaker output is used, the radio volume control affects the audio levels of the IP-223.

Jumper Position

Line 1

Line 2

Receive Input Impedance:

J14

J23

J17

J24

8 ohms (for a speaker input)

600 ohm

10k ohm

COR (Carrier Operated Relay) I/O (Input/Output)

The COR I/O connection indicates that audio is being received from the radio. The COR connection is provided at DIG6, pin

20 of the DB25 connector.

PTT Connection

Connect the radio PTT circuit to the PTT relay contact terminals on the DB25 connector. Usually the common of the relay

contact switch is grounded and the normally open contact connects to the PTT input. An alternative method to ground the

common of the relay internal to the unit is to jumper R377 (line 1) and R381 (line 2) with a piece of wire soldered closed.

Monitor Connection

Connect the radio MON circuit to the MON relay contact terminals on the DB25 connector. Usually the common of each relay

contact switch is grounded and the normally open contact connects to the MON input. An alternative method to ground the

common of the relay internal to the unit is to jumper R376 (line 1) and R380 (line 2) with a piece of wire soldered closed.

R1 and R2 Relays

The IP-223 provides two (2) relay closures for controlling the frequency of the radio, or switching a remote ancillary device.

The F1 and F2 contacts can be connected through the DB25 connector. Usually the common of each relay contact switch is

grounded and the normally open contact connects to the radio frequency control terminals. Information on programming the

R1 and R2 relays is provided in the “Setup Information” chapter of this manual starting on page 33. An alternative method to

ground the common of the relay R1 internal to the unit is to jumper R375 (line 1) and R379 (line 2), and for relay R2 jumper

R374 (line 1) and R378 (line 2) with a piece of wire soldered closed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tone/Console Operation

Digital I/O

In addition to the two standard relay closures, seven (7) lines of digital I/O are also included. These lines are open-collector

transistor outputs. They can be programmed on a per line basis to generate any of 128 combinations. They pull down to ground

and can be jumper selected to pull up to either +5V or the power supply voltage (minimum +12V).

Jumpers J8 (line 1) and J30 (line 2) are used to select the pull up voltage. Jumper position A pulls up to +5V and jumper

position B pulls to the power supply value.

NOTE:

Some radios provide a pull-up voltage. When this occurs, place the jumper into the null position. Information on

programming the digital I/O lines is provided in the “Setup Information” chapter of this manual starting on

page 33.

CTCSS (Continuous Tone Coded Squelch System) Connection

The IP-223 connection can be used for a recorder output or as a CTCSS output:

Recorder output - The analog audio is generated at the connection.

CTCSS output - Each function tone can be assigned a CTCSS number which corresponds to a CTCSS frequency. See

“CTCSS Tone Frequency Table” on page 131.

Tone/Console Operation

Tone and Console operation require jumpers set to specific locations. The following section discusses the jumper settings. See

“Jumper Locations” on page 125.

2-/4-Wire Jumper Settings

2-Wire / 4-Wire Selection:

2-Wire A position

Line 1

Line 2

J33 and J34

J5 and J6

4-Wire B position

The RX termination J14 (line 1) and J24 (line 2) should be placed in jumper position A on 4-wire systems for a single unit at

the end of a line. If multiple units are connected in parallel, only one (1) unit should have the RX termination jumper in the A

position. The RX termination jumper should be in the null position on the rest of the units.

For 2-wire operation:

•

PCB 750743 or PCB 750630 revision C and higher - Set J14 or J24 to the NULL position.

TX Side Settings

PCB 750743 or PCB 750630 revision C and higher

Two (2) jumpers on the transmit pair allow a degree of control over the output impedance. The jumper positions for each line,

depending on how many consoles are placed in parallel, are shown below.

NOTE:

PCB 750630 revision A does not have these jumpers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Level Settings

Jumper Position

Line 1

Line 2

Consoles in Parallel:

J17

J22

J10

J15

Output Impedance

600 ohms

1200 ohms

1800 ohms

2400 ohms

Local PTT I/O

The Local PTT I/O is used to generate TX Ethernet traffic on a local keyed system as opposed to the 2175Hz detection on a

tone keyed system. The input is at DIG5; pin 23 of the DB25 connector. The TX condition is caused by an active low.

Cross Mute I/O

Cross mute information to local consoles is provided at DIG0, pin 8 of the DB25 connector.

Supervisory I/O

Supervisory information to and from consoles is provided at DIG1, pin 21 of the DB25 connector. The supervisory I/O is both

an input and an output.

Supervisory input and output in console, tone or local mode behaves as follows:

Console Mode – Input - An Ethernet packet supervisor is sent on detection.

Output - When an Ethernet packet is received. The line level is set.

While under supervisory control, TX traffic from the Ethernet to the console is muted. The console’s

audio to the Ethernet is muted. Handset PTT and the IC button are disabled.

Tone Mode –

Input - An Ethernet packet supervisor is sent on detection.

Output - When an Ethernet packet is received, the line level is set.

When an Ethernet packet is received, the line level is set.

Local Mode -

Input- No affect on I/O.

Output - No affect, when Ethernet packet is received.

While under control, manual PTT and the IC button are disabled.

NOTE:

Information on programming the supervisory I/O is provided in the “Setup Information” chapter of this manual

starting on page 33..

Level Adjustments

Once the IP-223 unit is connected to the system, the level potentiometers can be set. Access to test and adjustment points on

newer versions of the IP-223 are provided through labeled openings on the case top and on the front panel of the unit. On older

versions of the IP-223, access to some of the test and adjustment points is provided through labeled openings on the front

panel; however, the case top needs to be opened to access the other test and adjustment points.

Download from Www.Somanuals.com. All Manuals Search And Download.

Level Adjustments

General Alignment

The IP-223 has a TX alignment tone and an RX alignment VU meter accessible from the front panel of the unit.

•

Press and hold the line button and then momentarily press the IC button twice to generate the 1kHz 0dB TX

alignment tone on both lines.

•

Press and hold the line button and then momentarily press the IC button three times to display the RX VU

meters.

Radio/Line TX Level

The Radio 1 TX test points (TP2 and TP6) and the Radio 2 TX test points (TP8 and TP9) are located on the front panel of the

IP-223. These provide a point to measure the actual signal being placed into the radio or balanced TX line. The front panel

accessible adjustment Radio 1 TX potentiometer (R47) and Radio 2 RX potentiometer (R61) are used to adjust these levels.

NOTE:

If the unit is placed into single-ended mode, the radio TX+ should be measured with respect to ground.

It is also possible to place jumper J9 (line 1) or J26 (line 2) into the A position to decrease the output of the TX line by a factor

of 10. The final adjustment should allow for undistorted audio to be transmitted for the full range of transmission levels at the

desired deviation. This can be accomplished by turning on the TX alignment tone and adjusting the TX output to 0dB, as

measured into a 600 ohm load.

Radio/Line RX Level

Standard Alignment Procedure for a 2- or 4- wire System:

•

Inject a 0dBm test tone on the RX pair (4-wire pins 12 and 24: 2-wire pins 13 and 25).

Measure the RX level on test point TP13 for line 1 or TP1 for line 2.

Adjust potentiometer R175 for line 1 or potentiometer R110 for line 2 until 0dBm is measured between the test

point and GND. (0dBM = 2VPP = .707VRMS)

•

Detune slightly 1-2dBm to provide overhead for large transients.

AGC (Automatic Gain Control) compression potentiometers RV5 for line 1 and RV1 for line 2 control the

aggressiveness of the AGC circuitry, if enabled. The AGC can be used to enhance the gain capabilities of the RX

circuitry. Set RV5/RV1 fully clockwise and, if required, back off 10 to15 degrees maximum.

•

Use the RX alignment tool (VU meter) accessed through the LCD display (press and hold the line button and

then momentarily press the IC button 3 times) to verify the dBm level. The reading should be 0dBm with the

AGC turned off. If the AGC is ON, it is likely the RX alignment software always displays 0dBm, the targeted

level for the AGC circuitry.

Line TX Monitor Level (Tone and Console Mode only)

PCB 750743 or PCB 750630 revision C and higher

The Line TX Monitor Level adjustment is used when the IP-223 is connected to consoles set in 4-wire mode. This allows for

local TX audio to be sent back on the Ethernet and played at other consoles so both sides of the radio traffic can be heard. The

alignment for TX monitor is similar to 4-wire RX alignment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation and Level Settings

To adjust the TX monitor, do the following:

1. In the options section of the Per Line Setup window, select the TX Monitor.

NOTE: If this feature is not necessary, or the line is in 2-wire mode, the TX Monitor field in the Options section on

the Per Line Setup window should be cleared.

2. Verify the RX alignment is completed first.

To perform a standard alignment for a 4-wire system, do the following:

1. Transmit a 0dBm test tone on the TX audio pairs pins 13 and 25.

2. Measure the RX level on test point TP13 for line 1 or TP1 for line 2.

3. Adjust potentiometer R390 for line 1 or potentiometer R391 for line 2 until 0dBm is measured between the test

point and GND. (0dBM = 2VPP = .707VRMS).

NOTE: Do not adjust the RX potentiometers.

4. Use the RX alignment tool (VU meter) accessed through the LCD display (press and hold the line button and then

momentarily press the IC button 3 times) to verify the dBm level.

CTCSS Level

The CTCSS level is measured by connecting an oscilloscope or RMS meter to ground and Radio 1 CTCSS test point (TP7) or

Radio 2 CTCSS test point (TP10). With the radio connected to the CTCSS output, have the remote console open to receive

audio so CTCSS is present. Adjust the Radio 1 CTCSS potentiometer (R50) or Radio 2 CTCSS potentiometer (R53) until the

desired level is achieved.

Frequency Decoding

The IP-223 is factory tuned to the frequencies shown below. The detection frequencies cannot be changed as they are coded

into the software. However, any actual function or output can be made to work with any existing programmed frequency.

Please consult the factory for special requirements for frequency selections.

Guard tone/PTT Tone: 2175 Hz

MON Function Tone: 2050 Hz

Frequency Select Function Tones (where used)

F1: 1950 Hz

F2: 1850 Hz

F3: 1750 Hz

F4: 1650 Hz

F5: 1550 Hz

F6: 1450 Hz

F7: 1350 Hz

F8: 1250 Hz

F9: 1150 Hz

F10: 1050 Hz

F11: 950 Hz

F12: 850 Hz

F13: 750 Hz

F14: 650 Hz

F15: 550 Hz

F16: 450 Hz

Download from Www.Somanuals.com. All Manuals Search And Download.

CHAPTER 4

Setup Information

The setup information for the IP-223 is accessed by using a web browser, such as Microsoft^®Internet Explorer. This section

describes the programming information for the IP-223. It includes information on setting the IP Address, accessing the IP-223

web setup windows, the setup window standards, and an explanation of the fields on each window used to program the IP-223.

Setting the IP Address Information

Before entering the setup information for the IP-223, the IP Address and Network Mask must be assigned to the IP-223 by

the use of a web browser or Windows™ HyperTerminal™ if the assigned IP Address is not accessible on your network.

Contact your network administrator to obtain the network IP Address and Mask.

For the IP-223 to interface successfully with the LAN or WAN, the IP Addresses of the IP-223 and your PC must be on the

same subnet. IP Addresses consist of four numbers separated by periods. For example, 10.2.99.101. For more information on

IP Addresses and subnets, consult your network administrator.

In order for the PC and the IP-223 unit to communicate via IP, both devices need to be in the same subnet.

NOTE:

For operation on different subnets, a gateway address must be configured.

An example of IP Addresses residing in the same subnet:

PC IP Address:10.2.99.250

IP-223 IP Address:10.2.99.251

IP-223 Network Mask:255.255.255.0

To display the IP Address and Network Mask assigned to the IP-223, do the following:

1. Connect power to the IP-223.

The IP Address and subnet mask are displayed on the LCD momentarily upon power up.

2. To check the IP Address and subnet mask at any other time, press and hold the line button on the front panel of the

IP-223, and then momentarily press the IC button.

The IP Address is displayed on the top line of the LCD, and the Network Mask is displayed on the bottom line of the

LCD.

Verify the IP Address and Network Mask obtained from your network administrator to the IP-223 addresses.

If the IP Address and Network Mask need to be set up using the serial port, see “Using HyperTerminal” below.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Using HyperTerminal

NOTE:

J35 must be in the A position.

To assign the IP Address and Network Mask using HyperTerminal, do the following:

1. Connect the IP-223 to your PC using a DB-9 serial cable.

2. From the Start menu on the computer, open the HyperTerminal Application, see Figure 84.

(Start|Programs|Accessories|Communications|HyperTerminal).

The HyperTerminal and Connection Description windows appear, see Figure 85.

FIGURE 84. HyperTerminal Navigation

3. In the Name field, enter com.

4. Click OK.

The Connect To window appears.

5. From the Connect Using drop down menu, select COM1.

6. Click OK.

The Com1 Properties window appears.

7. From the Bits per second drop down menu, select 19200.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the IP Address Information

8. From the Flow Control drop down menu, select None

NOTE: These parameters may be different than the defaults depending on the selected Serial Port Parameters, see

“Serial Port Parameters Drop Down Menu” on page 73.

Default

Drop down menu

Bits per second field: 19200

Data bits field:

Parity field: None

Stop bits field:

Flow control field: None

9. Click OK.

Setting

The Main HyperTerminal window appears.

FIGURE 85. Com Terminal Setup Windows

10. In the main HyperTerminal window, enter an uppercase S.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

11. Press ENTER.

Enter Password for Factory Setup appears.

FIGURE 86. HyperTerminal Window Password

12. Enter technobabble for the factory setup password.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the IP Address Information

13. Press ENTER.

The serial port access window shown in Figure 87 appears.

FIGURE 87. HyperTerminal Factory Setup Options – Serial Port Access Window

NOTE:

The serial number is fixed and should match the case label. The MAC (Media Access Control) address is

generated based on the serial number.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

The following is a brief explanation of the factory setup options shown in Figure 87:

A - Provides the ability to reset the unit.

B - Allows access to the password if it is new or forgotten.

C - Allows the unit to get an IP Address via DHCP, or to manually set the IP Address.

D - Allows the Subnet Mask to be manually entered or changed.

E - Allows the Gateway Address to be manually entered or changed.

F - Provides the ability to reset (back to defaults) the Board Parameters.

14. When Reset the Board’s password to None appears, type Y to reset the board’s password number to none, otherwise,

type N.

15. Press Enter.

16. When Should this target obtain IP settings from the network appears, type Y to obtain the IP settings from the

network, otherwise, type N.

17. Press Enter.

18. When Static IP Address appears, enter the IP Address of the IP-223, if necessary.

19. Press Enter.

20. When Subnet Mask IP Address appears, enter the Subnet Mask IP Address, if necessary.

21. Press Enter.

22. When Gateway address IP Address appears, enter the Gateway IP Address, if necessary.

23. Press Enter.

24. When Reset Board Params appears, type Y to reset the board parameters, otherwise type N.

25. Press Enter.

26. When “Do you wish to reset the unit now” appears, type Y if changes were made on the window, otherwise enter an

27. If changes were made on the window, press ENTER to reset the IP-223, otherwise proceed to the next step.

The changes made are saved to memory.

28. Close the HyperTerminal program.

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessing IP-223 Web Browser Configuration Windows

Before connecting the IP-223 to the web browser, an IP Address compatible with an existing network must be set. Details on

setting the IP Address and Network Mask are described earlier in “Setting the IP Address Information” on page 33.

The configured IP Address is the web browser address (http://XXX.XXX.XXX.XXX, the XXX’s refer to the values for the

assigned IP Address) used to access the IP-223 Web Setup windows.

To access the IP-223 web setup windows, do the following:

1. Open the web browser on the PC.

2. In the web address bar, enter the IP Address of the IP-223.

The Connect to [IP Address] window shown in Figure 88 appears.

FIGURE 88. Connect to [IP Address] Window

3. From the User Name drop down menu, type admin or the Username.

4. In the Password field, enter the appropriate Username password.

If this is the first time the IP-223 has been started and a password has not been assigned to the unit, no entry is

required.

5. Click OK.

The Welcome window appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

IP-223 Web Setup Windows Standards

Links

Across the top of each setup window are links used to access the various IP-223 configuration pages. On the left side of the

links header, the name assigned to the unit, the MAC address, and the version number of the firmware are displayed. A brief

description of each link is provided below.

FIGURE 89. IP-223 Links

TABLE 5. IP-2002 Links

Link

Description

Displays the “Welcome Window” on page 42.

Displays the “Basic Ethernet Setup Window” on page 43.

Displays the “General Gain Setup” on page 47.

Displays the “Multicast Address Setup Window” on page 49.

Displays the “Per Line Setup Window” on page 55.

Download from Www.Somanuals.com. All Manuals Search And Download.

IP-223 Web Setup Windows Standards

TABLE 5. IP-2002 Links

Displays the “Save to EEPROM Window” on page 90.

Displays the “Account Setup Window” on page 91.

Displays the “Additional Feature Setup Window” on page 100.

Displays the “Clone Console Window” on page 101.

Displays the “Crosspatch Setup Window” on page 102.

Displays the “CRP PIN Table Window” on page 108.

Displays the “Pass Change Window” on page 111.

Displays the “Tone Frequency & Durations Window” on page 112.

To access a setup window, do the following:

Click the desired link.

The window for the selected link appears.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Welcome Window

The Welcome window provides a basic description of the IP-223 operating modes and a field to enter a descriptive name for

the unit. This name is displays at the top of each IP-223 web setup window

NAVIGATION: Clicking the picture of the IP-223 on the links displays the Welcome window, shown in Figure 90.

FIGURE 90. Welcome Window

To change the name of the IP-223 unit, do the following:

1. In the Console Name field, enter the desired name (up to 12 characters).

2. Click Submit.

The name appears at the top of the setup window.

3. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

4. Click Save Parameters.

The changes made are saved to permanent memory.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Ethernet Setup Window

The Basic Ethernet Setup window is used to configure the IP-223 for use. The fields on this window are described on the

following pages

NAVIGATION: Clicking Basic Ethernet Setup displays the Basic Ethernet Setup window, shown in Figure 91.

Serial Number Field

The Serial Number field displays the serial number of your IP-223. The serial number label is located on the back of the

adapter box and should match the number in this field.

MAC Address

The MAC Address field displays the MAC Address of the IP-223.

FIGURE 91. Basic Ethernet Setup Window

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Base IP Setup

Use DHCP Server Check Box

The Use DHCP Server check box indicates whether or not DHCP (Dynamic Host Configuration Protocol) is used. If

selected, DHCP allows the IP-223 to acquire all of the information for operation on the network bypassing its manual entry.

NOTE:

Telex does not recommend operating with DHCP enabled. Operating with DHCP enabled may cause the base IP

Address to change unexpectedly making changes to the software setup more difficult. If employing 5/6-tone

selective calling and messaging, DHCP must not be used.

Unit IP Address Field

The Unit IP Address field identifies the unique base address assigned to the IP-223. This address identifies the unit for

operations such as setup, software upgrades and communications in some operating modes.

Subnet Mask Field

The Subnet Mask field identifies information used by the IP stack to determine if an IP Address is local or if an IP Address

requires the use of a gateway to be reached. Contact your network administrator to obtain the proper value for this field.

Gateway Address Field

The Gateway Address field identifies the IP Address of the node used to reach other networks. Contact your network

administrator to obtain the proper value for this field.

DNS (Domain Name Server) Number 1–3 Fields

The DNS Number 1–3 fields are currently not used by the IP-223.

Packet Setup

Packet Delay before Playback Field

The Packet Delay before Playback field identifies the length of delay before playback (jitter buffer). The IP-223 utilizes a

20ms UDP/IP (User Datagram Protocol/Internet Protocol) packet to encode audio. Some buffering of these packets must

occur before playback to help absorb network delays, jitters, and lost packets. The typical entry for this field is 6, which

translates to a delay of 120ms before playback (each packet is 20ms of audio). Larger values may be required for complicated

networks, and smaller values for less complicated networks.

The range for this field is 4 to 29.

QOS (Quality of Service): Precedence Bits Field

The QOS: Precedence Bits field is used to set the priority level of network traffic. Typically this value is left at 0 for normal

traffic and 5 for voice traffic.

The range for this field is 0 to 7.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Ethernet Setup Window

QOS: D, T, and R (Delay, Throughput, and Reliability) Bits Field

The QOS: D, T and R Bits field is used for advanced programming purposes. These bits are usually 0. Contact your network

administrator to obtain the appropriate value for this field.

Delay (D)

an active delay bit tells the router to choose a high speed to minimize delay

an active throughput bit specifies high capacity links should be used.

Throughput (T)

Routing (R)

an active routing bit directs routing protocols and network management applications to select

fault-tolerant paths.

For more information on the binary equivalent for delay, throughput, and reliability see Table 6 on page 45.

The range for this field is 0 to 7.

TABLE 6. D, T, R Binary Reference

Precedence Field

Binary Traffic Type

D, T, and R bits

Binary

(0)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

Best Effort

Background

Standard

(0)

(1)

(2)

(4)

Normal (Best Effort), minimal cost

Maximize Reliability

Maximize Throughput

Minimize Delay

Excellent Load

Controlled Load

Video

Voice

Network Control

Local Console IP Address

Local Computer IP Address 1-10 Fields

The Local Computer IP Address fields identify the base IP Address of up to 10 IP-223 units within the same room. These

fields are generally used when the selected line mode is console. The entries are used for the Ethernet crossmute function. The

IP-223 examines the source of the audio and flags it if the source from one of the IP-223 units listed in these fields.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

To configure the IP-223 for use, do the following:

1. From the links, select Basic Ethernet Setup.

The Basic Ethernet Setup window appears.

2. In the Unit IP Address field, enter the IP Address.

3. In the Subnet Mask field, enter the subnet mask address.

4. In the Gateway Address field, enter the gateway address, if required.

5. In the Unit Name field, enter a descriptive name.

6. In the Packet Delay before Playback field, enter the number of packets of delay for playback (each packet is 20ms of

audio).

7. In the QOS: Precendence Bits field, enter the number of bits, if required.

8. In the QOS: D, T, and R Bits field, enter the number of bits, if required.

9. In the Local Computer IP Address fields, enter the IP Addresses of the IP-223 units that are located in the same

room.

10. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

11. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

12. Click Save Parameters.

The entries are saved to permanent memory.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223.

IMPORTANT:

The submit button saves changes in temporary memory only.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console

Download from Www.Somanuals.com. All Manuals Search And Download.

General Gain Setup

The General Gain Setup window provides for an up or down adjustment of the gain levels for various parameters included on

the window. The IP-223 is based largely on software controlled resistors with a resolution of 1.5dB per step.

Example:

If it is determined the output level for a transmission line is 3.0dB too high, an entry of -3.0dB should be

entered in the corresponding Transmit Gain field for the line.

NAVIGATION: Clicking General Gain Setup displays the General Gain Setup window, shown in Figure 92.

FIGURE 92. General Gain Setup Window

Handset Gain Setup

Handset Mic Gain Drop Down Menu

The Handset Mic Gain drop down menu identifies the level, in dB, of gain for the handset mic.

The values for this field are: 12.0, 10.5, 9.0, 7.5, 6.0, 4.5, 3.0, 1.5, 0, -1.5, -3.0, -4.5, -10, -16, -22, -28, and -34.

Handset Sidetone Gain Drop Down Menu

The Handset Sidetone Gain drop down menu identifies the sidetone gain level, in dB, for the handset.

The values for this field are: -12, -14, -16, -18, -20, -22, -24, and MUTE.

Line Gain Setup

Receive Gain Drop Down Menu

The Receive Gain drop down menu identifies the receive gain, in dB, for either line 1 or line 2.

The values for this field are: 12.0, 10.5, 9.0, 7.5, 6.0, 4.5, 3.0, 1.5, 0, -1.5, -3.0, -4.5, -10, -16, -22, -28, and -34.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Transmit Gain Drop Down Menu

The Transmit Gain drop down menu identifies the transmit gain, in dB, for either line 1 or line 2.

The values for this field are: 12.0, 10.5, 9.0, 7.5, 6.0, 4.5, 3.0, 1.5, 0, -1.5, -3.0, -4.5, -10, -16, -22, -28, and -34.

CTCSS Gain Drop Down Menu

The CTCSS Gain drop down menu identifies the CTCSS gain, in dB, for either line 1 or line 2.

The values for this field are: 12.0, 10.5, 9.0, 7.5, 6.0, 4.5, 3.0, 1.5, 0, -1.5, -3.0, -4.5, -10, -16, -22, -28, and -34.

TX Voice Gain Field

The TX Voice Gain field allows you to set the transmit voice gain, in dB, for either line 1 or line 2.

The range for this field is 10dB to -60dB.

To adjust a signal level, do the following:

1. From the links, select General Gain Setup.

The General Gain Setup window appears.

2. From the Handset Mic Gain drop down menu, select the desired gain for the handset mic.

3. From the Headset Sidetone drop down menu, select the desired gain for the headset sidetone.

4. From the Receive Gain drop down menu, select the desired receive gain for the appropriate line.

5. From the Transmit Gain drop down menu, select the desired transmit gain for the appropriate line.

6. From the CTCSS Gain drop down menu, select the desired CTCSS gain for the appropriate line.

7. In the Tx Voice Gain field, enter the desired gain for the appropriate, if required.

8. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

9. From the links, click Save to EEPROM.

The Save Setup Parameters window appears.

10. Click Save Parameters.

The entries are saved to permanent memory.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223.

IMPORTANT:

The submit button saves changes in temporary memory only.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console

Download from Www.Somanuals.com. All Manuals Search And Download.

Multicast Address Setup Window

The Multicast Address Setup window identifies the mode of operation or line type, as well as which port the IP-223 uses to

communicate various line information on. Once a selection is made in the line type field, the fields necessary to enter the setup

information for the selected line type are enabled. The fields on this window are described on the following pages.

NAVIGATION: Clicking Multicast Address Setup displays the Multicast Port Number Setup window, shown in Figure 93.

FIGURE 93. Multicast Address Setup

Line Multicast Setup

Line Number Field

The Line Number field displays the appropriate line number for the specified parameters.

Enable via Ethernet Check Box

The Enable via Ethernet check box indicates whether or not Ethernet connectivity is used for the line number. If selected,

Ethernet connectivity is ON. Otherwise, audio received from the analog connections of the IP-223 are not echoed to the

Ethernet, and Ethernet traffic is not mixed into the audio of the IP-223.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Line Type Drop Down Menu

The Line Type drop down menu identifies the operating mode for Line number 1 and 2. The line type for all other operating

modes is displayed on the window. Selection of the line type enables the fields necessary to enter the setup information for the

selected line type.

FIGURE 94. Line Type Drop Down Menu

Available selections for this field are:

Local Mode – The radio is connected directly to the IP-223 allowing for simple migration and full local control of the

radio.

Tone Mode – The IP-223, based on Ethernet traffic, generates the keytones required to control standard, tone-equipped

radio circuit. This allows an existing tone decoder and radio to be connected. This mode also

supports a parallel analog console for local control.

Console Mode – Allows the use of existing tone-based consoles to the VoIP network. The IP-223 decodes standard tones,

converts it into Ethernet traffic for another IP-223 and optional parallel IP consoles.

Phone Mode – Using a PIB or TDI, a line on the IP-223 is used to connect to an analog phone line.

iDEN Radio – Using the NI-223, allows interface with a Falcon Class push-to-talk (PTT) mobile phone system.

TETRA Radio Mode – Used to interface to a TETRA digital trunked system using the IP-223 and the Sepura SRM2000

mobile radio. The IP-223 interfaces the radio through the PEI allowing dispatch access to TETRA

radio assets.

Line Name Field

The Line Name field is used to enter a descriptive name for the line.

This field can contain up to 12 characters.

RX Mcast Address Field

The RX Mcast (Multicast) Address field identifies the broadcast address for all audio traffic received on a specific line. All

consoles must have the same Multicast Address. The entry in the first Multicast Address field applies to the port number

entered in the RX Port field.

NOTE:

The option to use a different Multicast Address for the RX port is available. This provides flexibility and acts as

a filter.

The range for this field is 224.0.0.2 to 239.255.255.255.

Download from Www.Somanuals.com. All Manuals Search And Download.

Multicast Address Setup Window

RX Port Field

The RX Port field identifies the port number for each line. The port number must be unique, per line, and must be greater than

1054.

Based on the entries shown in Figure 93, any console attempting to transmit to line 1 must have a Multicast Address of

225.8.11.81 and an RX port number of 2054 to monitor RX audio and a TX port number of 4072 to monitor TX audio.

TX Mcast Address Field

TX Mcast (Multicast) Address field identifies the broadcast address for all audio traffic transmitted on a specific line. All

consoles must have the same Multicast Address. The entry in the second Multicast Address field applies to the port number

entered in the TX Port field.

NOTE:

IP-223s can also operate Unicast (point-to-point), these fields can support class A, B, and C addresses.

Make sure the RX and TX port numbers are unique.

The range for this field is 224.0.0.2 to 239.255.255.255.

TX Port Field

The TX Port field identifies the port number for each line. The port number must be unique, per line, and must be greater than

1054.

Example:

Based on the entries shown in Figure 93, any console attempting to transmit to line 1 must have a

Multicast Address of 225.8.11.81 and an RX port number of 2054 to monitor RX audio and a TX port

number of 4072 to monitor TX audio.

TX Group Port Field

The TX Group Port field is used to transmit to multiple IP-223s based on a unique port number.

TTL Field

The TTL (Time-To-Live) field identifies the number of routers the multicast audio packets go through before being stopped.

Your specific network design dictates this value. If audio is not reaching a particular node on the network, increasing this value

may correct the problem.

The range for this field is 1 to 128.

To define the parameters for a line number, do the following:

NOTE:

The following procedure outlines the entries required for each field on the Multicast Port Number Setup window.

Depending on the line type selected, all entries listed may not be required or available for the line type.

1. From the links, select Multicast Address Setup.

The Multicast Address Setup window appears.

2. Select the Enable via Ethernet check box, if Ethernet connectivity is used.

3. From the Line Type drop down menu, select the operating mode.

4. In the Line Name field, enter a descriptive name for the line.

5. In the first Multicast Address field, enter the Multicast Address for the RX port.

6. In the RX Port field, enter a unique RX port number.

7. In the second Multicast Address field, enter the Multicast Address for the TX port.

8. In the TX Port field, enter a unique TX port number.

9. In the TX Group Port field, enter the TX group port number, if applicable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

10. In the Channel Hops field, enter the number of channel hops (routers) the multicast audio packets can go through

before being stopped.

11. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

12. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

13. Click Save Parameters.

The entries are saved to permanent memory.

Vocoder Type Drop Down Menu

The Vocoder Type drop down menu, shown in Figure 95, indicates the bit rate at which audio is converted into digital format.

This feature is used to configure communication between the IP-223 and C-Soft.

Available selections for this field are: ADPCM (Adaptive Differential Pulse Code Modulation) 16K and ADPCM 32K.

NOTE:

Design considerations must take into account that although 16K uses less bandwidth, the audio quality might not

perform as desired.

IMPORTANT:

Vocoder configurations must be the same across devices and C-Soft.

FIGURE 95. Vocoder Type Drop Down Menu

Phone Setup

Enable Check Box

The Enable check box is used to setup a phone ring when phone calls are received. The entry for a ring signal must be a

unique Multicast Address and different from the other lines.

Line Name Field

The Line Name field is used to enter an alphanumeric label for the phone ring setup.

This field can contain up to 12 characters.

Multicast Address Field

The Multicast Address field is used to enter the multicast address for the ring. This number must be between 224.0.0.2 and

239.255.255.255. The console must be setup with the same multicast address in order to hear the phone ring.

Download from Www.Somanuals.com. All Manuals Search And Download.

Multicast Address Setup Window

Outgoing Port Field

The Outgoing Port field identifies the port number where the ring packet is generated. This number must be unique and be

between 1024 and 65535.

NOTE:

The ring Multicast Address and port number must match the console’s ring multicast setting to receive the ring

signal.

TTL Field

The TTL (Time-To-Live) field identifies the number of routers the multicast audio packets for the thing to pass through before

being discarded. Network design dictates this value. See your network administrator for further information.

This field range is 0–128, the default value is 6.

System Manager Setup

Enable Check Box

The Enable check box is used to enable communication with TSM (Telex System Manager). If unselected, TSM can not

detect the IP-223. By default, the check box is selected. TSM is used to update IP-223 firmware. To learn how to update

IP-223 firmware, see “Update Firmware” on page 111. See the Telex System Manager technical manual for operation details.

Name Field

The Name field displays Sys Manager and is not editable.

Multicast Address Field

The Multicast Address field displays the default Multicast Address used by TSM to detect connected VoIP hardware. This

value is not editable.

Incoming Port Field

The Incoming Port field identifies the port used to communicate with TSM. TSM requests data from the IP-223 through this

port. This field is automatically populated and is not editable.

Outgoing Port Field

The Outgoing Port field identifies the port used to communicate with TSM. The IP-223 sends data through this port to TSM.

This field is automatically populated and is not editable.

TTL Field

The TTL (Time To Live) field identifies the number of routers the multicast audio packets pass through before being

discarded. The value in this field is entered by default and used by TSM to communicate with VoIP hardware. This value is not

editable.

The range for this field is 1 to 128.

Tape Setup

Enable Check Box

The Enable check box is used to setup a tape recorder for the specified line.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Vocoder Type Drop Down Menu

The Vocoder Type drop down menu, shown in Figure 96, indicates the bit rate at which audio is converted into digital format.

This feature is used to configure communication between the IP-223 and C-Soft.

Available selections for this field are: ADPCM (Adaptive Differential Pulse Code Modulation) 16K and ADPCM 32K.

NOTE:

Design considerations must take into account that although 16K requires less bandwidth, the audio quality might

not perform as desired.

IMPORTANT:

Vocoder configurations must be the same across devices and C-Soft.

FIGURE 96. Vocoder Type Drop Down Menu

NOTE:

When Tape 1 is enabled, a separate stream is created with both RX and TX audio for that line. When Tape 2 is

enabled, a separate Ethernet stream is created with both RX and TX audio for that line. This stream can then be

recorded by a Telex Network Recorder.

Line Name Field

The Line Name field is used to assign a unique label to the tape line.

Mcast Address Field

The Mcast Address field is used to configure the Mulitcast Address used to generate multicast audio for the recorder.

Port Field

The Port field is used to configure the port used to generate multicast audio for the recorder.

TTL Field

The TTL (Time To Line) field identifies the number of routers the multicast audio packets pass through before being

discarded.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223.

IMPORTANT:

The submit button saves changes in temporary memory only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console

Per Line Setup Window

The Per Line Setup window identifies the parameters for the line type selected for the line on the Multicast Port Number

Setup window. The line number to which the details on the window apply is displayed at the top of the window. The line type

selected determines the window display and enables the appropriate fields on the window necessary to enter the setup

information for the line type.

NOTE:

Clicking Per Line Setup displays the Per Line Setup window, shown in Figure 97.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Per Line Setup Window—Local, Tone, and Console Mode Configuration

The Per Line Setup window for Local, Tone, or Console Mode configuration, see Figure 97, appear when Local, Tone or

Console is selected from the Line Type drop down menu on the Multicast Address Setup window.

FIGURE 97. Per Line Setup - Local, Tone, and Console Modes (view 1)

Line 1 Button

Select the Line 1 button is used to navigate to the Per Line Setup window for Line 1 configuration.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

Line 2 Button

The Line 2 button is used to navigate to the Per Line Setup window for Line 2 configuration.

Submit Button

To permanently save changes, do the following.

1. Click Submit.

The console name appears at the top of the Welcome window.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console.

Line Mode Status Field

The Line Mode Status field displays the line type assigned to the line in the “Multicast Address Setup Window” on page 49.

With the exception of digital output, CTCSS frequency, CTCSS default system and chan fields in the Function Tone Setup

section, the Per Line Setup window for Local, Tone, or Console mode contains the same configuration options and are

discussed below.

Port Enabled Check Box

The Port Enabled check box indicates whether or not the port is enabled. If selected, the port is enabled and selection of

transmission or play received audio is allowed.

COR Setup

LAM Enabled Check Box

The LAM (Line Activity Monitor) Enabled check box is used to monitor the line for the signal level configured in the LAM

Level field. see “LAM Level Field” on page 61.

COR Enabled Check Box

The COR Enabled check box indicates whether or not the COR I/O pins (DiG6, pin 20 of the DB25 connector) are enabled. If

selected, the IP-223 monitors the COR for line activity.

COR Active High check box

The COR Active High check box indicates whether or not the polarity of the COR is high. If selected, the COR active signal

is high.

NOTE:

LAM and COR can both be selected at the same time.

LAM and COR are used to check audio signal for processing.

CTCSS Setup

Always On Radio Button

The Always On radio button indicates whether or not CTCSS is ON at all times.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

On With PTT Radio Button

The On With PTT radio button indicates whether or not CTCSS is generated only when PTT is activated.

Tape Output Radio Button

The Tape Output radio button indicates whether or not CTCSS is generated. If selected, no CTCSS is generated. This audio

output is used as an analog sum of RX and TX audio for the line. The output port is a single ended capacitor coupled.

Delay Setup

TX Delay Field

The TX Delay field identifies the delay, in ms, of TX audio. When TX Ethernet packets arrive, the PTT relay is closed and TX

audio is delayed for the specified time. This provides the ability to overcome timing issues involving repeater attack time or

trunking (clear to talk) delays.

The range for this field is 0 to 2000ms.

RX Delay Field

The RX Delay field identifies the amount of time, in ms, RX audio is recorded and stored. RX audio is constantly recorded by

the IP-223 and when a COR or LAM triggered detect occurs, the IP-223 goes back the specified time of delay to start

generating Ethernet packets. This provides the ability to prevent lost first syllables using COR or LAM.

The range for this field is 0 to 1000ms.

Squelch Tail Delay Field

The Squelch Tail Delay field identifies the amount of time, in ms, the RX audio is muted after PTT occurs. This provides the

ability to overcome squelch tail ping-pong in crosspatch modes by muting the radio RX input after PTT occurs.

The range for this field is 0 to 5000ms.

Function Tone Setup

Jump To Entry Drop Down Menu

The Jump To Entry drop down menu allows you to select (in groups of 10) function tones to view and modify.

1. From the Jump To drop down menu, select the group of 10 function tones you want to view.

2. Click the Update button.

The function tones you select appear.

Update Button

The Update button searches and displays the selection you chose from the Jump To drop down list.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

Tone Enable Check Box

The Tone Enable check box indicates whether or not the function tone is active. If selected, the function tone is active. The

frequency for the tone is set on the Tone Frequency and Durations window described on page 112. The standard function tones

and their frequencies are the default entries. These entries are shown in Table 7 on page 114.

NOTE:

At least one function tone must be selected.

Relay Drop Down Menu

The Relay drop down menu, shown in Figure 98, identifies the relay(s), if any, closed immediately upon receipt of the

function tone.

Available selections for this field are: no selection, R01, R02, or BOTH.

FIGURE 98. Relay Drop Down Menu—Per Line Setup

Relay Group Drop Down Menu

The Relay Group drop down menu identifies if a relay is grouped into separate functions. This allows more than one relay to

be activated at any particular time by being in separate groups. For example, when F1 has R1 selected as its relay, and F2 has

R2 selected as its relay, setting the two Relay Group numbers to the same value allows multiple relays with different functions.

In this scenario, the relays for F1 and F2 are interlocked. When the Relay Group assigned to F1 and F2 are different, R2 does

not activate when F1 is received. Furthermore, when there is no relay selected for a function tone, but the assigned relay group

is used by another relay group, when the function tone is received, all relays in the group are activated. This allows relay R1

and R2 to be assigned to different groups and use other function tones within the same relay group to activate them.

Select either 1 or 2 from the drop down menu.

Relay Time (ms) Field

The Relay Time (ms) field identifies if the selected relay(s) latch ON when the function tone is received, or if the selected

relay(s) is latched ON for a specified period of time when the function tone is received. To program the relay(s) to latch ON

when the function tone is received enter a zero (0) in the field. To set the duration the relay(s) is latched ON, enter the desired

amount of time, in ms, in the field.

The range for this field is 0 to 32000.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Digital Output Field - Local Mode Only

The Digital Output field identifies the DIG0-DIG6 output for the function tone. Enter the numeric value shown in the Value

column in Table 9 “Digital Output Table” on page 133, for the desired DIG0-DIG6 output.

The range for this field is 0 to 127. H=high (ON), L=low (OFF). Using DIG6 for COR input limits the digital output value

from 0 to 63.

CTCSS Freq Field - Local Mode Only

The CTCSS Freq field identifies the CTCSS tone frequency set for the function tone. Enter the desired Tone Number shown

on Table 8 in “CTCSS Tone Frequency Table” on page 131. If zero (0) is entered, there is no CTCSS tone frequency set for the

function tone

CTCSS Default Check Box - Local Mode Only

The CTCSS Default check box indicates whether or not the entry in the CTCSS Freq field is ignored and the last selected

value is generated during PTT. For example, F1 is used for all transmissions and CTCSS Default is selected for F1. F2-F8 have

different CTCSS values programmed for them and the CTCSS Default check box is cleared. Selecting F2 and then keying up

on F1 sets the CTCSS tone to the F2 value. Selecting F4 sets the CTCSS tone to the F4 value. When PTT is pressed, F1 is the

default frequency and the F4 CTCSS tone is sent.

System Field - Local Mode

The System field is used to control radios serially connected to the IP-223. Once configured, the IP-223 directs audio to the

system entered in the field.

When the function tone is changed by the console operator, this setting, along with the Chan field setting, directs the radio to

the system and frequency configured in the field. This field works in conjunction with the Chan field.

This field can contain up to 3 digits.

Chan Field - Local Mode

The Chan field is used to control radios serially connected to the IP-223. Once configured, the IP-223 directs audio to the

channel (frequency) entered in the field.

When the function tone is changed by the console operator, this setting, along with the System field setting, directs the radio to

the system and frequency configured in the field. This field works in conjunction with the System field.

This field can be configured for up to 100 frequencies.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

FIGURE 99. Per Line Setup - Local Tone and Console Modes (view 2)

LAM Setup

LAM Level Field

The LAM Level field identifies the threshold, in dB, at which the radio/line un-mutes and sends RX packets to the Ethernet.

The range for this field is -50 to +10dB.

LAM Time Field

The LAM Time field identifies the amount of time, in seconds, the LAM level can drop below the threshold without action

from the IP-223. It allows small gaps in the audio sequence.

The range for this field is 0 to 60 sec.

Monitor Relay

The Monitor Relay field provides the IP-223 the ability to decode a valid Ethernet packet and provide a relay-contact output

to turn off the sub-audible-tone-decoder circuit in the radio receiver. This allows the console operator to monitor the line for

other users before transmission (required by FCC regulations on stations equipped with CTCSS). Select one of the following

operating modes for the monitor relay:

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Reset with PTT –

When selected, the monitor relay is closed from the time the monitor tone sequence is received

until the next PTT operation.

On except PTT –

Timed –

When selected, the monitor relay is latched at all times except when PTT is active, whether the

monitor function tone is received or not.

When selected, enter the amount of time, in ms, the monitor relay is latched.

Options

If an Options field cannot be selected, the particular option is not available for the line number to which the details on the

window apply.

Supervisor Check Box

The Supervisor check box indicates whether or not the Supervisory I/O pin (DIG1, pin 21 of the DB25 connector) is enabled.

If selected, parallel console supervisory control is enabled and control of the radio can be seized from other consoles.

Cross Mute Check Box

The Cross Mute check box indicates whether or not the crossmute I/O pin (DIG0, pin 8 of the DB25 connector) is enabled. If

selected, parallel console crossmute control is enabled. Crossmute is used to mute the parallel consoles during a parallel

transmission.

Full Duplex Check Box

The Full Duplex check box indicates whether or not full duplex audio is supported. If selected, full duplex (TX and RX

transmission) audio is allowed.

RxAGC Check Box

The RxAGC (Receive Automatic Gain Control) check box indicates whether or not the radio RX audio includes an AGC. If

selected, an AGC step is added to the radio RX audio. This results in the transmission of a more consistent radio RX audio by

increasing the level of low audio and decreasing the level of loud audio.

Hi-Pass RX Check Box

The Hi-Pass RX check box indicates whether or not RX audio below 300Hz is blocked. If selected, RX audio below 300Hz is

blocked.

Pre-Emphasize TX Check Box

The Pre-Emphasize TX check box indicates whether or not TX audio includes a standard 6dB octave pre-emphasis. If

selected, a standard 6dB octave pre-emphasis is included in the TX audio.

TX Monitor Check Box

The TX Monitor check box indicates whether or not TX audio from parallel consoles in 4-wire mode are sent to the Ethernet

as a transmit packet. If selected, TX audio from parallel consoles in 4-wire mode are sent to the Ethernet as a transmit packet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

2-Wire Check Box

The 2-Wire check box indicates whether or not the line number to which the details on the window apply is configured as

2-wire. If selected, the line number to which the details on the window apply is configured as a 2-wire line.

Parallel Console Check Box

The Parallel Console check box indicates whether or not a parallel console is being used (for example, a legacy tone console,

only available in console and tone mode). If selected, a parallel console is attached to the system.

NOTE:

Must be enabled when console is configured for EIA.

Must be enabled when configuring for Console Mode.

PTT Notch Filter Check Box

The PTT Notch Filter checkbox, when selected, indicates the 2175Hz notch filter is enabled. When selected, 2175Hz ±180Hz

frequency range is filtered during PTT. Use this option when 2175Hz is blocking desirable audio.

PTT Setup

The PTT Setup section allows a secondary external function to be controlled with a separate relay closure at the same time as

the PTT relay. Select one of the following:

PTT relay only –

PTT + R1 –

When selected, only the PTT relay is closed. (Default Setting)

When selected, both the PTT relay and the R1 relay close at the same time.

When selected, both the PTT relay and the R2 relay close at the same time.

When selected, the PTT relay, the R1 relay, and the R2 relay close at the same time.

PTT + R2 –

PTT + BOTH –

PTT Timeout Field

The PTT Timeout field is used to indicate how long, in seconds, to allow PTT to be active when no audio is transmitted. If a

time is entered in the field, PTT activity will timeout after the designated amount of time has lapsed. This feature is useful in

cases where the line goes offhook for an indefinite period of time due to a stuck PTT key.

The range for this field is 0 to 1800sec. To disable this feature, enter zero (0).

Serial Port Mode

Serial Port Mode Drop Down Menu

The Serial Port Mode drop down menu, shown in Figure 100, is used to identify the specific radio interface for the serial port

configuration. Selecting an item with a Scan List suffix enables a frequency scan list update function. The freq scan list

function synchronizes the console scan list with the radio's scan list.

By default, the serial port in Tone or Console mode is Normal.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Available selections for this field are: Normal, FleetSync Series 80, FleetSync Series 80 - Scan List, FleetSync Series 90,

FleetSync Series 150, FleetSync Series 150 - Scan List, FleetSync Series 180, FleetSync Series 180 - Scan List, Kenwood 5710

and /5810, EF Johnson 5300.

FIGURE 100. Serial Port Drop Down Menu - Local Mode

Serial Port Params Drop Down Menu

The Serial Port Params (Parameters) drop down menu identifies the configuration of the serial port data speed and format.

Serial port parameters refer to bit rate, parity, data bits, and stop bits.

The serial port parameters in Tone or Console mode is, by default, 19200.N.8.1

Available selections for this field in Local mode are: 300,N,8,1; 300,N,8,2; 300,E,7,1; 1200,N,8,1; 1200,N,8,2; 1200,E,7,1;

2400,N,8,1; 2400,N,8,2; 2400,E,7,1; 4800,N,8,1; 4800,N,8,2; 4800,E,7,1; 9600,N,8,1; 9600,N,8,2; 9600,E,7,1; 19200,N,8,1;

19200.N.8.1; 19200,E,7,1. See Figure 100.

FIGURE 101. Serial Port Params Drop Down Menu - Normal Mode

NOTE:

If necessary, refer to the Radio Dispatch and Signaling Equipment downloads available on the Telex website

(www.telex.com) for this setting based on the radio to be installed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

FIGURE 102. Per Line Setup - Local, Tone, and Console Mode (view 3)

Signaling Setup

The Signaling Setup section is used to setup encode, decode, tone type and digits pause and duration.

IMPORTANT:

The FleetSync features in this section are optional IP-223 accessories. See “IP-223 Accessories” on

page 15 for part numbers.

FleetSync Decode Check Box (Tone and Local Modes)

The FleetSync Decode check box is used to enable the line for radio IDs with FleetSync ANI capabilities to decode their alias,

ID numbers, and messages on Telex consoles within the system. If selected, Kenwood FleetSync's over-the-air ANI is enabled

and the ANI number or name is decoded via the ANI lookup tables and displayed on Telex IP based consoles.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

FleetSync Encode Check Box (Local Mode Only)

The FleetSync Encode check box indicates the line is enabled to encode Kenwood FleetSync signaling.This optional feature

enables FleetSync PTT ID, status, selective call, and text messaging.

If selected, “Additional Feature Setup Window” on page 100, must be configured.

MDC Decode Check Box (Tone and Local Modes)

The MDC Decode check box is used to enable the line to receive and decode Motorola MDC signaling to display ID numbers,

status IDs, emergency calls, and alerts. If selected, MDC signaling is enabled and the ID number or name is decoded via the

ANI lookup tables and displayed on Telex IP based consoles.

MDC Encode Check Box

The MDC Encode check box is used to enable the line to transmit and encode Motorola MDC signaling to display the

consoles ID number, status ID, emergency or alert. If selected, MDC Signaling is enabled and the ID number or name is

encoded via the ANI lookup tables and appears on the MDC radio in the field

IMPORTANT:

This feature is not enabled on versions 4.100 or earlier. The MDC Encode check box serves as a

placeholder for future implementation.

Tone Type Drop Down Menu

The Tone Type drop down menu, shown in Figure 103, identifies the signaling type used when receiving a call.

Available selections for this field are: None, CCIR1, CCIR2, DTMF, DZVEI, EEA, EIA, EURO, KENWOOD 5TONE, MODAT,

NATEL, PCCIR, PDZVEI, PZVEI, ZVEI1, and ZVE12.

FIGURE 103. Tone Type Drop Down Menu

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Local, Tone, and Console Mode Configuration

ANI Suffix Field

The ANI Suffix field identifies a 0 to 3 digit suffix is appended to the end of the ANI received. For example, if you have a

suffix 123 and the ANI 9876 is received, the IP-223 sends 9876123 to the consoles. This is useful if two (2) different lines

have duplicate ANI IDs.

Digit Duration Field

The Digit Duration field identifies the length of time, in ms, the digit tone is decoded when it is active for the signaling type

selected in the Tone Type drop down menu.

The range for this field is 0 to 100ms.

Interdigit Duration Field

The Interdigit Duration field identifies the length of time, in ms, between the digit tones for the signaling type selected in the

Tone Type drop down menu.

The range for this field is 0 to 100ms.

NOTE:

Some radio systems require an extended first tone, to allow time to activate the receivers.

Pause Duration Field

The Pause Duration field identifies the length of time, in ms, allowed between received groups for the signaling type selected

in the Tone Type drop down menu.

The range for this field is 0 to 100ms.

Preamble Duration Field

The Preamble Duration field identifies the length of time, in ms, the first tone is sent for the signaling type selected in the

Tone Type drop down menu.

The range for this field is 0 to 100ms.

Group Digit Field

The Group Digit field identifies the group digit. The group digit is a wild card that can represent any digit. Placing a group

digit within a filter allows any digit appearing at that location in the tone string to pass through the filter.

Field values can be 0 - 9 or A - F. The default is A.

Repeat Digit Field

The Repeat Digit field identifies the digit that separates two digits sent back to back. On occasion, radio system messages

require two of the same digits to be entered back to back. Use of repeat digits delimits tone duration ensuing continuous

transitions.

The default for this field is E.

ANI Decoder # Field

The ANI Decoder # field lists in sequential order the available ANI Decoders.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

ANI Call Type Drop Down Menu

The ANI Call Type drop down menu, shown in Figure 104, identifies the type of call for the ANI Decoder #.

Available selections for this field are: Emergency, Group, Individual, or Status.

FIGURE 104. ANI Call Type Drop Down Menu-Per Line Setup

ANI Call Format Field

The ANI Call Format field identifies the call string format for the ANI Decoder #. The format is a free form string entry of up

to 16 digits. These include digits 0 - 9, A-D (A-F for other formats), *, # and the following characters:

I (Caller ID) – Placed into the ID field of the ANI packet or the ANI field of the caller portion of the telegram. The ID is

stored as a 32-digit string in the packet.

G (Group Digits) – Stored in the Group section of the ANI packet. The group value is converted to a decimal number and

is stored as an 8-digit string in the packet.

S (Status) – Digits represented by S are interpreted as status information. These values are converted to decimal numbers

and stored as an 8-digit status string in the ANI packet. The console has a corresponding list of the status numbers and

descriptions that are displayed upon receipt of the packet.

P (Pause) – When inserted into the string, a pause is expected in this location. The pause duration is set in the Pause

Duration field (see “Pause Duration Field” on page 67).

R (Calling ID) – Used to delineate the location of the digits being used for a selective call. These digits represent the

address or ID of the person being called. They are stored in the ANI packet as an 8-digit string.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Phone Mode Configuration

The Per Line Setup window for Phone Mode configuration, see Figure 105, appears when Phone is selected from the Line

Type drop down menu on the Multicast Address Setup window. In Phone mode, the following options are available for per line

configuration.

FIGURE 105. Per Line Setup - Phone Mode (view 1)

Auto Answer Setup

Auto Answer Field

The Auto Answer field identifies the number of times the phone rings before the line goes offhook. This field is used to

remotely enable a IP-223 to PIB or TDI connection.

Auto Disconnect Time Field

The Auto Disconnect Time field identifies the amount of time, in seconds, before the IP-223 automatically places the PIB or

TDI adapter onhook or disconnects if the threshold entered in the LAM Level field described below is not reached.

Delay Setup

TX Delay Field

The TX Delay field identifies the delay, in ms, of TX audio. When TX Ethernet packets arrive, the PTT relay is closed and TX

audio is delayed for the specified time. This provides the ability to overcome timing issues involving repeater attack time or

trunking (clear to talk) delays.

The range for this field is 0 to 2000ms.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

RX Delay Field

The RX Delay field identifies the amount of time, in ms, RX audio is recorded and stored. RX audio is constantly recorded by

the IP-223 and when a COR or LAM triggered detect occurs, the IP-223 goes back the specified time of delay to start

generating Ethernet packets. This provides the ability to prevent lost first syllables using COR.

The range for this field is 0 to 1000ms.

LAM Setup

LAM Level Field

The LAM Level field identifies the threshold, in dB, at which the radio/line un-mutes and sends RX packets to the Ethernet.

The range for this field is -50 to +10dB.

LAM Time Field

The LAM Time field identifies the amount of time, in seconds, the console continues to play audio when receiving audio

above the LAM threshold specified in the LAM Level field. This entry is also used by the Ethernet to determine how long to

send audio.

The range for this field is 0 to 60 sec.

Mic Click Setup

Mic Click Call Enabled Check Box

The Mic Click Call Enabled check box indicates whether or not a remote radio user can click the radio PTT a specified

number of times within a specified period of time to dial a programmed number. If selected, a remote radio user can click the

radio PTT a specified number of times within a specified period and, upon receipt of this sequence, the IP-223 takes the PIB or

TDI offhook and automatically dials the number in the Click Dial String field.

Number of Clicks Field

The Number of Clicks field identifies the number of times the radio PTT must be pressed to automatically dial the number in

the Click Dial String field.

The range for this field is 1 to 5.

Time Between Clicks Field

The Time Between Clicks field identifies the amount of time, in ms, allowed between mic clicks.

The range for this field is 0 to 9999ms.

Click Dial String Field

The Click Dial String field identifies the number automatically dialed when the radio PTT is pressed the number of times

specified in the Number of Clicks field.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Phone Mode Configuration

Click Dial Timeout Field

The Click Dial Timeout field identifies the amount of time, in seconds, the phone rings before hanging up.

The range for this field is 10 to 60 sec.

FIGURE 106. Per Line Setup - Phone Mode (view 2)

Monitor Relay

The Monitor Relay field provides the IP-223 the ability to decode a valid Ethernet packet and provide a relay-contact output

to turn off the sub-audible-tone-decoder circuit in the radio receiver. This allows the console operator to monitor the line for

other users before transmission (required by FCC regulations on stations equipped with CTCSS). Select one of the following

operating modes for the monitor relay:

Reset with PTT – When selected, the monitor relay is closed from the time the monitor tone sequence is received until the

next PTT operation.

On except PTT –When selected, the monitor relay is latched at all times except when PTT is active, whether the monitor

function tone is received or not.

Timed – When selected, enter the amount of time, in ms, the monitor relay is latched.

Options

Relay Closure

R1 - Ring Check Box

The R1 - Ring check box indicates whether or not the R1 relay opens and closes in step with the ring cadence. If selected,

the R1 relay opens and closes in step with the ring cadence.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

R2 - OffHook Check Box

The R2 - OffHook check box indicates whether or not the R2 relay opens when the phone is taken offhook. If selected,

the R2 relay opens when the phone is taken offhook.

Rx AGC Enabled Check Box

The RxAGC Enabled check box indicates whether or not the phone audio includes an AGC. If selected, an AGC step is

added to the phone RX audio. This results in a more consistent phone RX audio by increasing the level of low audio and

decreasing the level of loud audio.

NOTE:

This is a software driven AGC. The per line hardware AGC is not used.

Keep Alive Digits Enabled Check Box

The Keep Alive Digits Enabled check box indicates whether or not keep alive digits are generated at the remote site or

responded to at a local site. Keep Alive Digits are responsible for verifying the phone connection status - active or inactive.

Star/Pound Keying Enabled Check Box

The Star/Pound Keying Enabled check box indicates whether or not an inbound caller on the phone line has the capability to

control the radio connected to the opposite line of the IP-223. Used in conjunction with Auto Answer and Auto Disconnect

Time, this function allows the user to key-up and key-down the radio. If selected, the inbound caller can key-up and key-down

the radio connected to the opposite line of the IP-223. The star key (*) keys up the radio, the pound key (#) keys down the

radio. Pushing double # hangs up the remote phone line.

Detect Tones Enabled Check Box

The Detect Tones Enabled check box indicates whether or not key-up tones detected on the phone line automatically keys up

the radio on the opposite line of the IP-223. This parameter is used in Radio Phone Mode.

Hook Flash Time Field

The Hook Flash Time field identifies the amount of time, in ms, an offhook line is temporarily placed during a hook flash.

The range for this field is 0 to 9999ms.

Network Call Timeout Field

The Network Call Timeout field identifies the amount of time, in minutes, before a network call is automatically placed

onhook.

The range for this field is 0 to 60min.

Station ID Field

The Station ID field is used to enter a unique ID number to identify the line. This ID is sent after an auto-answer event.

This field can contain up to 12 digits.

Busy Channel Lockout Check Box

The Busy Channel Lockout check box indicates outgoing FleetSync messages are placed in queue until the radio is idle.

FleetSync messages can be lost when sent on half-duplex radios. Selecting this check box avoids lost messages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Phone Mode Configuration

RP251/550 Setup

NOTE:

These features support legacy PSTN radio control systems.

C550 Operation Enabled Check Box

The C550 Operation Enabled check box indicates whether or not operation of the C-550 console is enabled. If selected,

operation of the C-550 console is enabled.

RP251 Operation Enabled Check Box

The RP251 Operation Enabled check box indicates whether or not operation of the RP-251 panel is enabled. If selected,

operation of the RP-251 dial-up remote station panel is enabled.

RP251 Access Digits Field

The RP251 Access Digits field identifies the three (3) digit access code assigned to the RP-251 panel.

RP251 Connect Digits Field

The RP251 Connect Digits field identifies the three (3) digit connect code sent to the console at the time of connection.

Serial Port Mode

Serial Port Mode Drop Down Menu

The Serial Port Mode drop down menu is used to identify the specific radio interface for the serial port configuration.

Selecting an item with a Scan List suffix enables a frequency scan list update function. The freq scan list function

synchronizes the console scan list with the radio's scan list.

The serial port in Phone mode is, by default, Normal.

Serial Port Parameters Drop Down Menu

The Serial Port Params drop down menu identifies the configuration of the serial port data speed and format. Serial port

parameters refer to bit rate, parity, data bits, and stop bits. The Baud rate is used in phone mode. If phone mode is enabled on

line 1, this is the rate used to connect to the IP-223 via the HyperTerminal.

The default setting for the field, 19200.N.8.1, is not configurable.

If necessary, refer to the Radio Dispatch and Signaling Equipment downloads available on the Telex website

(www.telex.com/RadioDispatch/) for this setting based on the radio to be installed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

FIGURE 107. Serial Port Params Drop Down Menu - Phone Mode

FIGURE 108. Per Line Setup - Phone Mode (view 3)

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—Phone Mode Configuration

Signaling Setup

The Signaling Setup section is used to setup encode, decode, tone type and digits pause and duration.

FleetSync Decode Check Box

The FleetSync Decode check box is used to enable the line for radio IDs with FleetSync ANI capabilities to decode their alias,

ID numbers, and messages on Telex consoles within the system. If selected, Kenwood FleetSync's over-the-air ANI is enabled

and the ANI number or name is decoded via the ANI lookup tables and displayed on Telex IP based consoles.

MDC Decode Check Box

The MDC Decode check box is used to enable the line to receive and decode Motorola MDC signaling to display ID numbers,

status IDs, emergency calls, and alerts. If selected, MDC signaling is enabled and the ID number or name is decoded via the

ANI lookup tables and displayed on Telex IP based consoles.

Tone Type Drop Down Menu

The Tone Type drop down menu, shown in Figure 109, identifies the signaling type used when receiving a call.

Available selections for this field are: None, CCIR1, CCIR2, DTMF, DZVEI, EEA, EIA, EURO, KENWOOD 5TONE, MODAT,

NATEL, PCCIR, PDZVEI, PZVEI, ZVEI1, and ZVE12.

FIGURE 109. Tone Type Drop Down Menu

ANI Suffix Field

The ANI Suffix field identifies a 0 to 3-digit suffix appended to the end of the ANI received. For example, if you have a suffix

123 and the ANI 9876 is received, the IP-223 sends 9876123 to the consoles. This is useful if two different lines have duplicate

ANI IDs.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Digit Duration Field

The Digit Duration field identifies the length of time, in ms, the digit tone is decoded when it is active for the signaling type

selected in the Tone Type drop down menu.

The range for this field is 0 to 100ms.

Interdigit Duration Field

The Interdigit Duration field identifies the length of time, in ms, between the digit tones for the signaling type selected in the

Tone Type drop down menu.

The range for this field is 0 to 100ms.

NOTE:

Some radio systems require an extended first tone, to allow time to activate the receivers.

Pause Duration Field

The Pause Duration field identifies the length of time, in ms, allowed between received groups for the signaling type selected

in the Tone Type drop down menu.

The range for this field is 0 to 100ms.

Preamble Duration Field

The Preamble Duration field identifies the length of time, in ms, the first tone is sent for the signaling type selected in the

Tone Type drop down menu.

The range for this field is 0 to 100ms.

Group Digit Field

The Group Digit field identifies the group digit. The group digit is a wild card that represents any digit. Placing a group digit

within a filter allows any digit appearing at that location in the tone string to pass through the filter.

Field values can be 0 - 9 or A - F. The default is A.

Repeat Digit Field

The Repeat Digit field identifies the digit that separates two digits sent back to back. On occasion, radio system messages

require two of the same digits to be entered back to back. Use of repeat digits delimits tone duration ensuing continuous

transitions.

The default for this field is E.

ANI Decoder Field

The ANI Decoder # field labels the row of the ANI Call you are formatting.

ANI Call Type Drop Down Menu

The ANI Call Type drop down menu, shown in Figure 110, identifies the type of call for the ANI decoder number entered in

the ANI Call Format Field.

Available selections for this field are: Emergency, Group, Individual, or Status.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—iDEN Radio Configuration

FIGURE 110. ANI Call Type Drop Down Menu

ANI Call Format Field

The ANI Call Format field, identifies the call string format for the ANI Decoder #.

This field can contain up to 16 digits,

ANI Call formats include digits 0 - 9, A-D (A-F for other formats), *, # and the following characters:

I (Caller ID) –

Placed into the ID field of the ANI packet or the ANI field of the caller portion of the telegram. The

ID is stored as a 32-digit string in the packet.

G (Group Digits) – Stored in the Group section of the ANI packet. The group value is converted to a decimal number and

is stored as an 8-digit string in the packet.

S (Status) –

Digits represented by S are interpreted as status information. These values are converted to decimal

numbers and stored as an 8-digit status string in the ANI packet. The console has a corresponding list

of the status numbers and descriptions that are displayed upon receipt of the packet.

P (Pause) –

When inserted into the string, a pause is expected in this location. The pause duration is set in the

Pause Duration field (see “Pause Duration Field” on page 67).

R (Calling ID) –

Used to delineate the location of the digits being used for a selective call. These digits represent the

address or ID of the person being called. They are stored in the ANI packet as an 8-digit string.

Per Line Setup Window—iDEN Radio Configuration

The Per Line Setup window for iDEN Radio configuration, see Figure 111, appears when iDEN is selected from the Line

Type drop down menu on the Multicast Address Setup window. In iDEN mode, the following options are available for per line

configuration. DEN operation and field programming, download the NI-223 manual at www.telex.com/radio dispatch.

For more information on iDEN operation and field programming, download the NI-223 manual from

www.telex.com/radiodispatch.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

FIGURE 111. Per Line Setup - iDEN Radio Mode (view 1)

Delay Setup

TX Delay Field

The TX Delay field identifies the delay, in ms, of TX audio. When TX Ethernet packets arrive, the PTT relay is closed and TX

audio is delayed for the specified time. This provides the ability to overcome timing issues involving repeater attack time or

trunking (clear to talk) delays.

The range for this field is 0 to 2000ms.

RX Delay Field

The RX Delay field identifies the amount of time, in ms, RX audio is recorded and stored. RX audio is constantly recorded by

the IP-223 and when a LAM or COR, triggered detect occurs, the IP-223 goes back the specified time of delay to start

generating Ethernet packets. This provides the ability to prevent lost first syllables using LAM or COR.

The range for this field is 0 to 1000ms.

Squelch Tail Delay Field

The Squelch Tail Delay field identifies the amount of time, in ms, the RX audio is muted after PTT occurs. This provides the

ability to overcome squelch tail ping-pong in crosspatch modes by muting the radio RX input after PTT occurs.

The range for this field is 0 to 5000.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—iDEN Radio Configuration

Function Tone Setup

Jump To Entry Drop Down Menu

The Jump To Entry drop down menu allows you to select (in groups of 10) function tones to view and modify.

1. From the Jump To drop down menu, select the group of 10 function tones you want to view.

2. Click Update.

The function tones you select appear.

Update Button

The Update button searches and displays the selection you chose from the Jump To drop down list.

Tone Enable Check Box

The Tone Enable check box indicates whether or not the function tone is active. If selected, the function tone is active. The

frequency for the tone is set on the Tone Frequency and Durations window described on page 114. The standard function tones

and their frequencies are the default entries. These entries are shown in Table 7 on page 114.

NOTE:

At least one function tone must be selected.

Relay Drop Down Menu

The Relay drop down menu, shown in Figure 112, identifies the relay(s), if any, closed immediately upon receipt of the

function tone.

Available selections for this field are: no selection, R01, R02, or BOTH.

FIGURE 112. Relay Drop Down Menu-Per Line Setup

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Relay Group Drop Down Menu

The Relay Group drop down menu identifies if a relay is grouped into separate functions. This allows more than one (1) relay

to be activated at any particular time by being in separate groups.

For example, when F1 has R1 selected as its relay, and F2 has R2 selected as its relay, setting the two (2) Relay Group

numbers to the same value allows multiple relays with different functions. In this scenario, the relays for F1 and F2 are

interlocked. When the Relay Group assigned to F1 and F2 are different, R2 does not activate when F1 is received.

Furthermore, when there is no relay selected for a function tone, but the assigned relay group is used by another relay group,

when the function tone is received, all relays in the group are activated. This allows relay R1 and R2 to be assigned to different

groups and use other function tones within the same relay group to activate them.

Select either 1 or 2 from the drop down menu.

Relay Time (ms) Field

The Relay Time (ms) field identifies if the selected relay(s) latch ON when the function tone is received, or if the selected

relay(s) is latched ON for a specified period of time when the function tone is received. To program the relay(s) to latch ON

when the function tone is received, enter a zero (0) in the field. To set the duration the relay(s) is latched ON, enter the desired

amount of time, in ms, in the field.

The range for this field is 0 to 32000. H=high (on), L=low (off)

Call Type Drop Down Menu

The Call Type drop down menu, shown in Figure 113 identifies the iDEN radio call type.

Available selections for this field are: Direct Connect, Group Call, Call Alert, or Emergency Group Call.

FIGURE 113. Call Type Drop Down Menu - iDEN Mode

iDEN Number Field

The iDEN Number field is used to enter the iDEN ID number for the function tone setup. Consult the manufacturer’s

technical data for ID formatting guidelines.

This field can contain up to 17 characters.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—iDEN Radio Configuration

FIGURE 114. Per Line Setup - iDEN Mode (view 2)

LAM Setup

LAM Level Field

The LAM Level field identifies the threshold, in dB, at which the radio/line unmutes and sends RX packets to the Ethernet.

The range for this field is -50 to +10dB.

LAM Time Field

The LAM Time field identifies the amount of time, in seconds, the console continues to play audio when receiving audio

above the LAM threshold specified in the LAM Level field. This entry is also used by the Ethernet to determine how long to

send audio.

The range for this field is 0 to 60 sec.

Monitor Relay

The Monitor Relay field provides the IP-223 the ability to decode a valid Ethernet packet and provide a relay-contact output

to turn off the sub-audible-tone-decoder circuit in the radio receiver. This allows the console operator to monitor the line for

other users before transmission (required by FCC regulations on stations equipped with CTCSS).

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Select one of the following operating modes for the monitor relay:

Reset with PTT –

On except PTT –

Timed –

When selected, the monitor relay is closed from the time the monitor tone sequence is received

until the next PTT operation.

When selected, the monitor relay is latched at all times except when PTT is active, whether the

monitor function tone is received or not.

When selected, enter the amount of time, in ms, the monitor relay is latched.

Options

If an Options field cannot be selected, the particular option is not available for the line number to which the details on the

window apply.

Full Duplex Check Box

The Full Duplex check box indicates whether or not full duplex Ethernet is supported. If selected, full duplex (TX and RX

transmission) audio packets are allowed.

RxAGC Check Box

The RxAGC (Automatic Gain Control) check box indicates whether or not the radio RX audio includes an AGC. If selected,

an AGC step is added to the radio RX audio. This results in the transmission of a more consistent radio RX audio by increasing

the level of low audio and decreasing the level of loud audio.

Hi-Pass RX Check Box

The Hi-Pass RX check box indicates whether or not RX audio below 300Hz is blocked. If selected, RX audio below 300Hz is

blocked.

Pre-Emphasize TX Check Box

The Pre-Emphasize TX check box indicates whether or not TX audio includes a standard 6dB octave pre-emphasis. If

selected, a standard 6dB octave pre-emphasis is included in the TX audio.

F1 Last Call Check Box (iDEN Mode only)

The F1 Last Call check box indicates whether or not the last call is reserved for the F1 button. If selected, function tone 1 is

reserved for the last call. This allows the console operator to call back the last call received.

PTT Notch Filter Check Box

The PTT Notch Filter checkbox, when selected, indicates the 2175Hz notch filter is bypassed. When selected, 2175Hz

±180Hz frequency range is ignored during PTT. Use this option when 2175Hz is blocking desirable audio.

Busy Channel Lockout Check Box

The Busy Channel Lockout check box indicates outgoing FleetSync messages are placed in queue until the radio is idle.

FleetSync messages can be lost when sent on half-duplex radios. Selecting this check box avoids lost messages.

PTT Setup

The PTT Setup section allows a secondary external function to be controlled with a separate relay closure at the same time as

the PTT relay. Select one of the following:

PTT relay only – When selected, only the PTT relay is closed. (Default Setting)

Download from Www.Somanuals.com. All Manuals Search And Download.

Per Line Setup Window—iDEN Radio Configuration

PTT + R1 – When selected, both the PTT relay and the R1 relay close at the same time.

PTT + R2 – When selected, both the PTT relay and the R2 relay close at the same time.

PTT + BOTH – When selected, the PTT relay, the R1 relay, and the R2 relay close at the same time.

PTT Timeout Field

The PTT Timeout field is used to configure the length of time in seconds the IP-223 allows the radio to key up. This function

is used to prevent an extensive occupation of the interfaced radio.

The range for this field is 0 to 1800sec. To disable this feature, enter zero (0).

Serial Port Mode

Serial Port Mode Drop Down Menu

The Serial Port Mode drop down menu is used to identify the specific radio interface for the serial port configuration.

Selecting an item with a Scan List suffix enables a frequency scan list update function. The Freq Scan List function

synchronizes the console scan list with the radio's can list.

The serial port in iDEN mode is, by default, iDEN.

Serial Port Parameters Drop Down Menu

The Serial Port Params drop down menu identifies the configuration of the serial port data speed and format. Serial port

parameters refer to bit rate, parity, data bits, and stop bits.

The default setting for the field, 19200.N.8.1, is not configurable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Per line Setup Window—Tetra Radio Configuration

The Per Line Setup window for Tetra Radio configuration, see Figure 115, appears when Tetra is selected from the Line

Type drop down menu on the Multicast Address Setup window. In Tetra mode, the following options are available for per line

configuration.

FIGURE 115. Per Line Setup - Tetra Mode (view 1)

Function Tone Setup

Jump To Entry Drop Down Menu

The Jump To Entry drop down menu allows you to select (in groups of 10) function tones to view and modify.

1. From the Jump To drop down menu, select the group of 10 function tones you want to view.

2. Click the Update button.

The function tones you select appears.

Update Button

The Update button searches and displays the selection you chose from the Jump To drop down list.

Tone Enable Check Box

The Tone Enable check box indicates whether or not the function tone is active. If selected, the function tone is active. The

frequency for the tone is set on the Tone Frequency and Durations window described on page 112. The standard function tones

and their frequencies are the default entries. These entries are shown in Table 7 on page 114.

NOTE:

At least one (1) function tone must be selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per line Setup Window—Tetra Radio Configuration

Relay Drop Down Menu

The Relay drop down menu identifies the relay(s), if any, closed immediately upon receipt of the function tone.

Available selections for this field are: no selection, R01, R02, or BOTH.

FIGURE 116. Relay Drop Down Menu

Relay Group Drop Down Menu

The Relay Group drop down menu identifies if a relay is grouped into separate functions. This allows more than one (1) relay

to be activated at any particular time by being in separate groups. For example, when F1 has R1 selected as its relay, and F2

has R2 selected as its relay, setting the two (2) Relay Group numbers to the same value allows multiple relays with different

functions. In this scenario, the relays for F1 and F2 are interlocked. When the Relay Group assigned to F1 and F2 are different,

R2 does not activate when F1 is received. Furthermore, when there is no relay selected for a function tone, but the assigned

relay group is used by another relay group, when the function tone is received, all relays in the group are activated. This allows

relay R1 and R2 to be assigned to different groups and use other function tones within the same relay group to activate them.

Select either 1 or 2 from the drop down menu.

Relay Time (ms) Field

The Relay Time (ms) field identifies if the selected relay(s) latch ON when the function tone is received, or if the selected

relay(s) is latched ON for a specified period of time when the function tone is received. To program the relay(s) to latch ON

when the function tone is received enter a zero (0) in the field. To set the duration the relay(s) is latched ON, enter the desired

amount of time, in ms, in the field.

The range for this field is 0 to 32000ms.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Type Drop Down Menu

The Type drop down menu, shown in Figure 117 identifies the type of call for Sepura radio configuration.

Trunked GC (Group Call) –

A half duplex point-to-multi-point call where immediate

communication takes place between the calling and the called users.

Trunked HDPC (Half Duplex Private Call) –

A half duplex point-to-point call between caller and called units. Each

unit asks permission to transmit before each transaction.

Trunked UDSL (User Defined Scan List) – A scan of specific groups predefined in the radio and in the IP-223. A UDSL is

a collection of pre-defined talk group (or function tone) settings. The UDSL

string entered in the ISSI/GSSI Number field is separated by the semicolon. It

can accept up to 10 trunked groups.

Direct GC –

Communication with other TETRA radios without the use of the network. This

is called DMO (Direct Mode Operation).

FIGURE 117. Type Drop Down Menu - Tetra Mode

NOTE:

For more information on TETRA operation and field programming, download the Sepura Application Note at

www.telex.com/radiodispatch

ISSI/GSSI Number Field

The ISSI/GSSI Number field identifies the group number or unit number for the selected Sepura radio type.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per line Setup Window—Tetra Radio Configuration

FIGURE 118. Per lIne Setup - Tetra Mode (view 2)

Delay Setup

TX Delay Field

The TX Delay field identifies the delay, in ms, of TX audio. When TX Ethernet packets arrive, the PTT relay is closed and TX

audio is delayed for the specified time. This provides the ability to overcome timing issues involving repeater attack time or

trunking (clear to talk) delays.

The range for this field is 0 to 2000ms.

RX Delay Field

The RX Delay field identifies the amount of time, in ms, RX audio is recorded and stored. RX audio is constantly recorded by

the IP-223 and when a LAM or COR triggered detect occurs, the IP-223 goes back the specified time of delay to start

generating Ethernet packets. This provides the ability to prevent lost first syllables using LAM or COR.

The range for this field is 0 to 1000ms.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

LAM Setup

LAM Level Field

The LAM Level field identifies the threshold, in dB, at which the radio/line un-mutes and sends RX packets to the Ethernet.

The range for this field is -50 to +10dB.

LAM Time Field

The LAM Time field identifies the amount of time, in seconds, the console continues to play audio when receiving audio

above the LAM threshold specified in the LAM Level field. This entry is also used by the Ethernet to determine how long to

send audio.

The range for this field is 0 to 60 sec.

Monitor Relay

The Monitor Relay field provides the IP-223 the ability to decode a valid Ethernet packet and provide a relay-contact output

to turn off the sub-audible-tone-decoder circuit in the radio receiver. This allows the console operator to monitor the line for

other users before transmission (required by FCC regulations on stations equipped with CTCSS). Select one of the following

operating modes for the monitor relay:

Reset with PTT –

On except PTT –

Timed –

When selected, the monitor relay is closed from the time the monitor tone sequence is received

until the next PTT operation.

When selected, the monitor relay is latched at all times except when PTT is active, whether the

monitor function tone is received or not.

When selected, enter the amount of time, in ms, the monitor relay is latched.

Options

If an Options field cannot be selected, the particular option is not available for the line number to which the details on the

window apply.

Full Duplex Check Box

The Full Duplex check box indicates whether or not full duplex Ethernet is supported. If selected, full duplex (TX and RX

transmission) audio packets are allowed.

RxAGC Check Box

The RxAGC check box indicates whether or not the radio RX audio includes an AGC. If selected, an AGC step is added to the

radio RX audio. This results in the transmission of a more consistent radio RX audio by increasing the level of low audio and

decreasing the level of loud audio.

Hi-Pass RX Check Box

The Hi-Pass RX check box indicates whether or not RX audio below 300Hz is blocked. If selected, RX audio below 300Hz is

blocked.

Download from Www.Somanuals.com. All Manuals Search And Download.

Per line Setup Window—Tetra Radio Configuration

Pre-Emphasize TX Check Box

The Pre-Emphasize TX check box indicates whether or not TX audio includes a standard 6dB octave pre-emphasis. If

selected, a standard 6dB octave pre-emphasis is included in the TX audio.

PTT Notch Filter Check Box

The PTT Notch Filter checkbox, when selected, indicates the 2175Hz notch filter is bypassed. When selected, 2175Hz

±180Hz frequency range is ignored during PTT. Use this option when 2175Hz is blocking desirable audio.

Busy Channel Lockout Check Box

The Busy Channel Lockout check box indicates outgoing FleetSync messages are placed in queue until the radio is idle.

FleetSync messages can be lost when sent on half-duplex radios. Selecting this check box avoids lost messages.

PTT Setup

The PTT Setup section allows a secondary external function to be controlled with a separate relay closure at the same time as

the PTT relay. Select one of the following:

PTT relay only – When selected, only the PTT relay is closed. (Default Setting)

PTT + R1 –

PTT + R2 –

When selected, both the PTT relay and the R1 relay close at the same time.

When selected, both the PTT relay and the R2 relay close at the same time.

PTT + BOTH – When selected, the PTT relay, the R1 relay, and the R2 relay close at the same time.

PTT Timeout Field

The PTT Timeout field is used to indicate how long, in seconds, to allow PTT to be active when no audio is transmitted. If a

time is entered in the field, PTT activity will timeout when no audio is transmitted for the designated amount of time. This

feature is useful in cases where the line goes offhook for an indefinite period of time due to a stuck PTT key.

The range for this field is 0 to 1800sec. To disable this feature, enter zero (0)

Serial Port Mode

Serial Port Mode Drop Down Menu

The Serial Port Mode drop down menu is used to identify the specific radio interface for the serial port configuration.

Selecting an item with a Scan List suffix enables a frequency scan list update function. The Freq Scan List function

synchronizes the console scan list with the radio's scan list.

The serial port in Tetra mode is, by default, Sepura. For more information see the manufacturer's technical documentation.

Serial Port Parameters Drop Down Menu

The Serial Port Params drop down menu identifies the configuration of the serial port data speed and format. Serial port

parameters refer to bit rate, parity, data bits, and stop bits.

The default setting for the field, 19200.N.8.1, is not configurable.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Save to EEPROM Window

The Save to EEPROM window is used to save the current configuration to the IP-223 or to reset the parameters on the

configuration webpage to the last configuration saved to the IP-223.

NAVIGATION: Clicking Save to EEPROM displays the Save Parameters and Reset IP-223 command buttons, shown in

Figure 119

FIGURE 119. Save to EEPROM

Save Parameters Button

The Save Parameters button is used to save any changes submitted to the IP-223 for storage into permanent memory.

Reset IP-223 Button

The Reset IP-223 button is used to perform a full reset of the IP-223. This is the software version of a power down reset.

To save changes to permanent memory, do the following:

1. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

2. Click Save Parameters.

The parameters are saved to permanent memory.

NOTE:

If the Submit button on an individual setup window was not selected before moving to another window, any

changes made to the entries on the window are not saved to permanent memory even when the Save Parameters

Button is selected.

To reset the IP-223, do the following:

1. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

2. Click Reset IP-223.

A momentary loss of connectivity occurs and the window shown in Figure 120 appears. The connection is restored

after several seconds.

3. Click a link to access a setup window, otherwise close the web browser.

Download from Www.Somanuals.com. All Manuals Search And Download.

Account Setup Window

FIGURE 120. Reset IP-223

Account Setup Window

The Account Setup window allows you to manage system and user accounts. The fields on this window are described on the

following pages.

NAVIGATION: Clicking Account Setup displays the Account Setup window shown in Figure 126.

System Accounts

By default, the IP-223 comes with two (2) system accounts created: admin and user. Upon first use, there are no passwords set

for either account. You can change the passwords for both of the accounts, if desired. These are the only system accounts

allowed.

Admin System Account

The Admin System account has privileges to change, modify or delete anything within the IP-223 software configuration. The

account rights are not configurable, except for the password.

User System Account

The User System account is used to is used to manage the system user account password. The system user account is in edit

mode when the username field is highlighted yellow.

Created Accounts

Created accounts are user-defined accounts that may have different defined permissions to selected areas of the IP-223

configuration software. You can create up to five (5) accounts of this type. To create a user defined account, see “Add New

User Button” on page 94.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

FIGURE 121. Account Setup

System Accounts

Enable Check Box

The Enable check box indicates whether the username is active or not. When selected, the username is active.

NOTE:

The admin system account is always enabled.

Username Display Column

The Username display column displays the username of the system account. This field is not configurable.

Password Field

The Password field displays the password for the system account. The password is shown in asterisks (******) for security

purposes.

The range for this field is a 4–16 character alphanumeric password.

New Password Field

The New Password field is used to enter a new password for the system account.

The range for this field is a 4–16 character alphanumeric password.

Download from Www.Somanuals.com. All Manuals Search And Download.

Account Setup Window

Confirm Password Field

The Confirm Password field is used to confirm the password you entered in the New Password field. This password must

match the password entered in the New Password field.

Edit Button

The Edit button is used to make changes to the user system account password. The edit button is inactive until the user account

is enabled.

To enable the user account, do the following:

1. Select the enable check box next to the account,

2. Click Submit.

The edit button becomes active.

NOTE: The only configurable fields are the New Password field and the Confirm Password field. Also, when the

Edit window is open, a Set No Password check box appears. For more information, see “Edit System

Accounts Window” on page 94.

Save Button

The Save button is used to temporarily save the change you have made to the system account. You must click the Submit

button to save the change made to the console.

Remember, you must Submit the changes to the console, too. The data is not stored in permanent memory until it is saved, as

explained in “Save Parameters Button” on page 90.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223. The submit

button saves changes in temporary memory only.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console

Created Accounts

Delete, Username, Password, New Password, Confirm Password Display Columns

The Delete, Username, Password, New Password, Confirm Password display columns display the existing user accounts

(up to 5) you have created.

NOTE:

Under the Delete column, a check box is shown. If the check box is selected, the account is marked for

deletion.Click the Delete button to delete the user account. The deletion is not complete until it is saved, as

explained in “Save Parameters Button” on page 90.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Delete Button

The Delete button is used to delete the selected user account(s). User accounts are marked for deletion by selecting the Delete

check box.

Add New User Button

The Add New User button opens the Create New User window. From this window, you can create a user profile with

selectable permissions. For more information, see “Add New User Window” on page 96.

System Parameters

Reset System Parameters Button

The Reset System Parameters button resets all parameters in the IP-223 to their factory defaults.

Edit System Accounts Window

The Edit System Account window, shown in Figure 122, is used to edit the user system account. When the Edit button is

selected, the user system account becomes highlighted in yellow. You can only change the Password or set the account to have

No Password from this window.

NAVIGATION: Clicking the Edit button displays the Edit System Account window shown in Figure 122.

FIGURE 122. Edit System Account

Download from Www.Somanuals.com. All Manuals Search And Download.

Edit System Accounts Window

Once you have made the change to the user system account, the following message appears at the top of the Account Setup

window.

FIGURE 123. Success Message

NOTE:

The information is not stored in permanent memory until it is saved, as explained in “Save Parameters Button”

on page 90

To change the admin System Account Password, do the following:

1. In the Current Password field, enter the current password (if this is the first time you are changing the password,

leave the field blank).

2. In the New Password field, enter a new password.

The password can be 4-16 alpha-numeric characters in length.

3. In the Confirm Password field, enter the password again.

4. Click Save.

5. Click the Save to EEPROM link at the top of the page.

The Save to EEPROM window appears.

6. Click Save Parameters to save the changes to the IP-223.

NOTE: To change the system account password from an actual password to no password, leave the New Password

and Confirm password fields blank, and then press Save.

To change the user system account password or edit the account, do the following:

1. Select the Enable check box next to the user username.

2. Click Submit.

Once enabled, the New Password, Confirm Password fields, Edit and Save buttons become active.

3. In the New Password field, enter a new password.

The password can be 4-16 alpha-numeric characters in length.

4. In the Confirm Password field, enter the password again.

5. Click Save.

6. Click the Save to EEPROM link at the top of the page.

The Save to EEPROM window appears.

7. Click Save Parameters to save the changes to the IP-223.104

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Add New User Window

The Create New User window is used to create up to five (5) new user account. From this window, you can assign

permissions to certain users. The fields for this window are described on the following pages.

NAVIGATION: Selecting the Add New User button from the Account Setup window opens the Add New User window, see

Figure 124.

FIGURE 124. Add New User—Account Setup

Choose a Username

Username Field

The Username field identifies the username of the account you are creating.

This field can contain up to 16 alphanumeric characters.

Password Field

The Password field identifies the password required to logon to this user account.

The range for this field is a 4–16 alphanumeric password.

Confirm Password Field

The Confirm Password field is used to confirm the password you entered into the Password field. This password must match

exactly with the Password field entry.

Download from Www.Somanuals.com. All Manuals Search And Download.

Add New User Window

Set Permissions

Additional Feature Check Box

The Additional Feature check box indicates access is granted to make changes to the Additional Feature page. This

permission is automatically granted to every user and is not configurable.

Save To EEPROM Check Box

The Save to EEPROM check box indicates permission is granted to use the Save to EEPROM page. By default, permission to

change configurations in this window is granted on every created account. See “Save to EEPROM Window” on page 90, for

more information.

Welcome Page Check Box

The Welcome Page check box indicates permission is granted to change the name of the console’s welcome window. By

default, permission to change the name of this window is granted on every created account. See “Welcome Window” on

page 42, for more information.

Account Setup Check Box

The Account Setup check box indicates access is granted to the Account Setup window.

Basic Ethernet & Multicast Setup Check Box

The Basic Ethernet Setup check box indicates permission is granted to the Basic Ethernet Setup and Multicast Address Setup

windows where changes can be made by the user. See “Basic Ethernet Setup Window” on page 43, and “Multicast Address

Setup Window” on page 49 for more information.

Clone Console & Pass Change Check Box

The Clone Console & Pass Change check box indicates permission is granted to the Clone Console and Pass Change

windows where changes can be made by the user. See “Clone Console Window” on page 101, and “Pass Change Window” on

page 111 for more information.

CRP Setup & PIN Table Check Box

The CRP Setup & PIN Table check box indicates access is granted to make changes to the CRP Setup and PIN Table pages.

When enabled, users are able to make changes to these pages.

General Gain Check Box

The General Gain check box indicates access is granted to make changes to the General Gain page. This permission is

automatically granted to every user and is not configurable.

Per Line Setup Check Box

The Per Line Setup check box indicates access is granted to make changes to the Per Line Setup page. When enabled, users

are able to make changes to the page.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Tone Freq & Durations Check Box

The Tone Freq & Durations check box indicates access is granted to make changes to the Tone Freq & Durations page. When

enabled, users are able to make changes to the page.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223. The Submit

button saves changes in temporary memory only.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console.

Cancel Button

The Cancel button discards the user account settings you have made and reopens the Account Setup window.

Download from Www.Somanuals.com. All Manuals Search And Download.

Edit Created Accounts Window

The Edit Created Account window, as seen in Figure 125, is used to edit a created account (user).

NAVIGATION: Clicking the Edit button for the user account displays the Edit Created Account window shown in

Figure 125.

NOTE:

For more information about the different permissions check box selections, see “Set Permissions” on page 97.

FIGURE 125. Edit Created Account—Account Setup

NOTE:

If you do not want to have a password for the user, be sure to select the Set no PIN check box.

Once you have completed making changes, click Save to save the changes. Otherwise, click Cancel to discard the changes

made.

NOTE:

The information is not stored in permanent memory until it is saved, as explained in “Save Parameters Button”

on page 90.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Additional Feature Setup Window

The Additional Feature setup window activates special features enabled by purchasing an option string from Telex.

Examples of special features are Kenwood’s Fleetsync and Motorola’s MDC1200 Over-the-Air ANI decoder. For more

information contact Telex Sales. Have the unit serial number available when purchasing this option.

NAVIGATION: Clicking Additional Feature displays the Additional Feature Setup window shown in Figure 126.

FIGURE 126. Additional Feature Access

To activate a special feature, do the following:

1. From the links, select Additional Feature.

The Additional Feature Setup window appears.

2. In the enter Access Key field, enter the 16-digit option string.

3. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

4. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

5. Click Save Parameters.

The entries are saved to permanent memory.

100

Download from Www.Somanuals.com. All Manuals Search And Download.

Clone Console Window

The Clone System Parameters window provides the ability to copy the setup information, other than the serial number, base

IP Address and mask address from one IP-223 unit to another IP-223 unit.

NAVIGATION: Clicking Clone Console displays the Retrieve Configuration Data from Remote IP-223 window shown in

Figure 127.

FIGURE 127. Clone System Parameters

To copy configuration data from one IP-223 unit to another IP-223 unit, do the following:

1. Connect both IP-223 units to the Ethernet network.

2. Follow the steps in “To access the IP-223 web setup windows, do the following:” on page 39 to access the IP-223

web setup windows for the IP-223 unit the configuration data is to be copied to.

3. From the links, select Clone Console.

The Retrieve Configuration Data from Remote IP-223 window appears.

4. In the Enter IP Address field, enter the IP Address of the remote IP-223 the configuration data is to be copied from.

5. Enter the username and password of the local IP-223.

6. Click Submit.

The setup information, other than the serial number, base IP Address, and mask address is sent to the IP-223 for

storage.

7. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

8. Click Save Parameters.

The entries are saved to permanent memory.

101

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Crosspatch Setup Window

The Crosspatch Setup window provides the necessary parameters to connect the IP-223s together via the Ethernet network.

The fields on this window are described on the following pages.

This window can contain up to 100 entries.

NAVIGATION: Clicking Crosspatch Setup displays the Crosspatch Setup window shown in Figure 128.

FIGURE 128. Crosspatch Setup

102

Download from Www.Somanuals.com. All Manuals Search And Download.

Crosspatch Setup Window

Local Setup

Enable Line – Line Check Box

The Enable Line – Line check box indicates whether or not audio can be routed from one line to another line. If selected,

audio is routed from one line to the other line. TX traffic from the console overrides the crosspatch to allow the console

operator to take control of the line.

Start Patch FTone Drop Down Menu

NOTE:

When using the Start and Stop FTone, the Line-Line check box must NOT be selected.

The Start Patch FTone drop down menu identifies the Ethernet function tone selection that starts a crosspatch between line 1

and line 2.

Stop Patch FTone Drop Down Menu

The Stop Patch FTone drop down menu identifies Ethernet function tone selection that stops a crosspatch between line 1 and

line 2.

Remote Setup

RCP Enable Check Box

The RCP Enable check box indicates whether or not RCP (Remote Crosspatch) is enabled. If selected, RCP is enabled.

Dialing Digits Field

The Dialing Digits field identifies the number of DTMF (Dual Tone Multi-Frequency) digits allowed in the Drop All, Add

String, and Delete String fields on the window.

The entry can be 2, 3, or 4.

Interdigit Time Field

The Interdigit Time field identifies the amount of time, in ms, allowed between DTMF digits before a reset occurs. If a reset

occurs, the DTMF sequence must be started again.

This range for this field is 0 to 32000ms

Beep Dly Field

The Beep Dly field identifies the amount of time, in ms, between the digit string detection and status beeps echoed back to the

hand-held radio.

The range for this field is 0 to 5000ms.

103

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Patch Timeout Field

The Patch Timeout field identifies the amount of time, in seconds, allowed for inactivity on an active patch. If a patch is

inactive for the specified period of time, the patch is dropped.

The range for this field is 0 to 999seconds.

NOTE:

Patch Timeout must be greater than Global Timeout.

Global Field

The Global field identifies the amount of time, in seconds, allowed for any patch.

The range for this field is 0 to 32000seconds.

Drop All Field

The Drop All field identifies the DTMF digit sequence used to drop all current patches. The number entered must be the

number of digits specified in the Dialing Digits field.

The range for this field is 0 to 9999seconds.

RCP Tables

The required fields depend on the mode selected:

XPATCH - requires #1 or #2, IP Address, Add String and Delete String

DIAL - requires Phone, Add String and Delete String

DLVOIP - requires Rx Multicast/Port, Tx Multicast/Port, Add String and Delete String

PHONEP - requires Add String and Delete String

LPTCH - requires Add String and Delete String

RCP Tables

Jump To Entry Drop Down Menu and Go Button

The Jump To Entry drop down menu allows you to select (in groups of (10)) function tones to view and modify.

1. From the Jump To drop down menu, select the entries you want to view.

2. Click the GO button.

The function tones you select appears.

Entry Field

The Entry field labels the row for the crosspatch entry.

Add String Field

The Add String field identifies the DTMF digit sequence to add this crosspatch entry. The number entered must be the

number of digits specified in the Dialing Digits field.

This field can contain up to 4 digits.

104

Download from Www.Somanuals.com. All Manuals Search And Download.

Crosspatch Setup Window

Delete String Field

The Delete String field identifies the DTMF digit sequence to delete this crosspatch entry. The number entered must be the

number of digits specified in the Dialing Digits field.

This field can contain up to 4 digits.

Mode Drop Down Menu

The Mode drop down menu identifies the crosspatch mode used for the crosspatch entry number. The crosspatch modes

available are:

FIGURE 129. Crosspatch Setup - Mode Drop Down Menu

XPTCH – Crosspatch to a remote IP-223. the IP Address and line number is required.

DIAL –

A remote user with a portable radio can key a DTMF string, causing the IP-223 to take the PIB or TDI

offhook, dial a pre-programmed phone number and establish a patch between the devices.

DLVOIP – A remote user with a portable radio can key a DTMF string, causing the IP-223 to join different multicast

groups and ports, which can cause mapping the IP to a different line.

PHONEP – A remote user with a portable radio can key a DTMF string, causing the IP-223 to take the PIB or TDI

offhook. Once the PIB or TDI is offhook, the user can manually dial a phone number.

LPTCH – Line-to-line crosspatch. Enable and disable using DTMF strings.

Phone Field (DIAL option only)

The Phone field identifies the phone number to be dialed for this crosspatch entry.

This field can contain up to 21 digits.

#1 or #2 Drop Down Menu (XPATCH option only)

The #1 or #2 drop down menu identifies which DB25 connector port on the remote IP-223 is used in this crosspatch entry.

Available selections for this field are: Radio1 or Radio 2.

105

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

FIGURE 130. #1 or #2 Drop Down Menu-Crosspatch Setup

IP Address Field (XPATCH option only)

The IP Address field identifies the IP Address of the remote IP-223 with a radio used in this crosspatch entry.

Rx Multicast Field (DLVOIP option only)

The Rx Multicast field identifies the broadcast address for the RX audio traffic used in this crosspatch entry. To inter-operate,

all consoles must have the same base Multicast Address.

The range for this field is 224.0.0.2 to 239.255.255.255.

Rx Port Field (DLVOIP option only)

The Rx Port field identifies the RX port number for this crosspatch entry.

The RX port number must be unique and must be greater than 1054.

Tx Multicast Field (DLVOIP option only)

The Tx Multicast field identifies the broadcast address for the TX audio traffic used in this crosspatch entry. To inter-operate,

all consoles must have the same base Multicast Address.

The range for this field is 224.0.0.2 to 239.255.255.255.

Tx Port Field (DLVOIP option only)

The Tx Port field identifies the TX port number for this crosspatch entry.

The TX port number must be unique and must be greater than 1054.

Command Buttons

NOTE:

If any changes have been made to the entries on the window, the Submit button must be selected before selection

of any other command button on the window. If the Submit button is not selected before the selection of another

command button, any changes made to the entries on the window are cleared.

Prev 10 Button

The Prev 10 button is used to traverse the window between crosspatch entries 1 and 100.

106

Download from Www.Somanuals.com. All Manuals Search And Download.

Crosspatch Setup Window

Next 10 Button

The Next 10 button is used to traverse the window between crosspatch entries 1 and 100.

To define the crosspatch parameters, do the following:

1. From the links, select Crosspatch Setup.

The Crosspatch Setup window appears.

2. Select the Line-Line Enable check box to route audio from one line to another line.

3. From the Start Patch FTone drop down menu, select the function tone that starts a crosspatch between two radios.

4. From the Stop Patch FTone drop down menu, select the function tone that stops a crosspatch between two radios.

5. Select the RCP Enable check box to enable RCP.

6. In the Dialing Digits field, enter the number of DTMF digits allowed in the Drop All, Add String, and Delete Strings

fields on the window.

7. In the Interdigit Time field, enter the amount of time (in ms) allowed between DTMF digits before a reset occurs.

8. In the Beep Dly field, enter the amount of time (in ms) between digit string detection and status beeps echoed back.

9. In the Patch Timeout field, enter the amount of time (in seconds) allowed for inactivity on an active patch before the

patch is dropped.

10. In the Global field, enter the amount of time (in seconds) allowed for inactivity on all patches before all patches are

dropped.

11. In the Drop All field, enter the DTMF digit sequence to drop all current patches.

NOTE: The DTMF digit sequence entered must be the number of digits specified in the Dialing Digits field in step 6.

12. Complete Entry 1 in the RCP Tables, if applicable:

13. In the Add String field, enter the DTMF digit sequence to add this crosspatch entry.

NOTE: The DTMF digit sequence entered must be the number of digits specified in the Dialing Digits field in step 6.

14. In the Delete String field, enter the DTMF digit sequence to delete this crosspatch entry.

NOTE: The DTMF digit sequence entered must be the number of digits specified in the Dialing Digits field in step 6.

15. From the Mode drop down menu, select the desired crosspatch mode.

16. In the Phone field, enter the phone number of the phone to be dialed.

17. From the #1 or #2 drop down menu, select the applicable DB25 connector port used on the remote IP-223.

18. In the IP Address field, enter the IP Address of the remote IP-223 with the radio used in this crosspatch entry.

19. In the Rx Multicast field, enter the Multicast Address for the RX audio traffic.

20. In the Rx Port field, enter a unique RX port number.

21. In the Tx Multicast field, enter the Multicast Address for the TX audio traffic.

22. In the Tx Port field, enter a unique TX port number.

23. When all entries in the RCP Table are complete for entry 1, repeat steps 13 through 22 above to complete the

required remote crosspatch entries on this window.

24. If all of the remote crosspatch entries are complete on the window and more crosspatches need to be defined, click

Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

If all of the remote crosspatch entries are complete on the window and no more crosspatches need to be defined, click

Submit.

AND

proceed to step 28.

The entries currently displayed on the window are sent to the IP-223 for storage.

107

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

25. Click Next 10 to toggle to the next Crosspatch Setup window.

26. Complete steps 13 through 22 for all desired crosspatch entries on the window.

27. After all crosspatches have been entered, click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

28. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

29. Click Save Parameters.

The entries are saved to permanent memory.

CRP PIN Table Window

The Remote CrossPatch Pin Setup window allows up 300 PIN numbers to be set for operation of the IP-223’s crosspatch

feature. The fields on this window are described on the following pages.

NAVIGATION: Clicking CRP PIN Table displays the Remote Crosspatch Pin Setup window shown in Figure 131.

FIGURE 131. Remote Crosspatch Pin

When PIN numbers are entered correctly, a Go-Ahead Beep sequence to indicate success or failure is played back on the

console indicating RCP setup is ready.

NOTE:

The Interdigit Time field entry on the Crosspatch Setup window also applies to PIN entry.

108

Download from Www.Somanuals.com. All Manuals Search And Download.

CRP PIN Table Window

Jump To Entry Drop Down Menu and Go Button

The Jump To Entry drop down menu allows you to select (in groups of 30) function tones to view and modify.

1. From the Jump To drop down menu, select the entries you want to view.

2. Click GO.

The function tones you select appears.

Submit Button

The Submit button is used to upload changes to the IP-223.

IMPORTANT:

The submit button saves changes in temporary memory only.

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console.

PIN Setup

PIN Enable Check Box

The PIN Enable check box indicates whether or not a PIN number is required to create a crosspatch. If selected, a PIN number

is required to create a crosspatch.

Entry Field

The Entry field allows for 300 PIN numbers.

PIN Field

The PIN field identifies the PIN for the displayed crosspatch entry number.

The range for this field is a 4-digit PIN.

Submit Button

The Submit button, located at the bottom of each configuration window, is used to upload changes to the IP-223.

IMPORTANT:

The Submit button saves changes in temporary memory only.

109

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

To permanently save changes, do the following:

1. Click Submit.

The changes are sent to the IP-223 in temporary storage.

2. Click Save to EEPROM.

The Save to EEPROM window opens.

3. Click Save Parameters.

Changes are now permanently saved to the IP-223 console.

Prev 30 Entries Button

The Prev 30 Entries button is used to traverse the window between crosspatch PIN entries 1 and 300.

Next 30 Entries Button

The Next 30 Entries button is used to traverse the window between crosspatch PIN entries 1 and 300.

To define crosspatch PIN numbers, do the following:

1. From the links, select CRP PIN Table.

The Remote CrossPatch Pin Setup window appears.

2. Select the PIN Enable check box if a PIN number is required to create a crosspatch.

3. In the PIN field, enter a PIN number for the crosspatch number.

4. Continue entering a four digit PIN number for the crosspatch numbers until all required PIN entries are complete on

the window.

5. If all of the PIN entries are complete on the window and more PINs need to be defined, click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

If all required Crosspatch PIN entries are complete on the window and no more PINs need to be defined, click

Submit

AND

proceed to step 9.

The entries currently displayed on the window are sent to the IP-223 for storage.

6. Click the Next 30 button to move to the next Remote CrossPatch Pin Setup window.

7. Repeat the steps 3 though 5 above to continue entering the Crosspatch PIN entries until all of the required PIN

entries have been completed.

8. After all PINs have been entered, click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

9. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

10. Click Save Parameters.

The entries are saved to permanent memory.

110

Download from Www.Somanuals.com. All Manuals Search And Download.

Pass Change Window

The Account Password Change window is used to assign a password, see “Accessing IP-223 Web Browser Configuration

Windows” on page 39.

NAVIGATION: Clicking Pass Change displays the Account Password Change window shown in Figure 132.

FIGURE 132. Account Password Change

Enter the desired four-digit number in the provided fields. If the two (2) PINs entered are the same, the password number is

entered into memory. The password is required to be entered in the Password field on the Connect to [IP Address] window to

access the web setup windows for the IP-223.

NOTE:

The password entered does not take effect until the IP-223 has been reset.

To define a password for the administrator’s user name, do the following:

NOTE: Make note of the new password before adding or changing a password number.

1. From the links, select Pass Change.

The administrator’s Account Password Change window appears.

2. In the New Password field, enter a four digit password number.

3. In the Confirm Password field, enter the four digit password number assigned in the previous step.

4. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

5. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

6. Click Save Parameters.

The entries are saved to permanent memory.

7. Click Reset IP-223.

A momentary loss of connectivity occurs and the window shown in Figure 120 appears. The connection is restored in

several seconds.

111

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Tone Frequency & Durations Window

The Tone Frequency and Durations window identifies frequencies and function tones. The IP-223 is capable of generating

the standard tone packages required to control a radio with a tone termination panel. The fields on this window are described

on the following pages.

NAVIGATION: Clicking Tone Frequency & Durations displays the Tone Frequency and Durations window shown in

Figure 133.

FIGURE 133. Tone Frequency and Durations

Monitor Frequency

Monitor Frequency Field

The Monitor Frequency field identifies the value, in Hz, of the function tone sent when the MON button on the console is

pressed. In most cases, this value is set at 2050Hz.

The range for this field is 0 to 3200 Hz.

112

Download from Www.Somanuals.com. All Manuals Search And Download.

Tone Frequency & Durations Window

Guard Hold

PTT Frequency Drop Down Menu

The PTT Frequency drop down menu, shown in Figure 134, identifies the PTT frequency, in Hz, the console uses.

Available selections for this field are: 2100, 2175, 2300, 2325, 2400, 2600, 2800, 2850 and 2970Hz.

FIGURE 134. PTT Frequency Drop Down Menu

Guard Tone Duration Field

The Guard Tone Duration field identifies the amount of time, in ms, the guard tone plays before the function tone.

The range for this field is 0 to 999ms.

Guard Tone Magnitude Field

The Guard Tone Magnitude field identifies the level, in dBm, of the guard tone.

The range for this field is -60 to 12dB.

Hold Tone Magnitude Field

The Hold Tone Magnitude field identifies the level, in dBm, of the hold tone summed with TX audio to keep the radio in a

transmit state.

The range for this field is -60 to 12dB.

Hold Tone Hangtime Field

The Hold Tone Hangtime field identifies the amount of time, in ms, the hold tone continues after the release of the PTT

button. Pressing the PTT button again during this hangtime continues the transmission without resending the guard and

function tones.

The range for this field is 0 to 999ms.

113

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

Function Tone

Function Tone Duration Field

The Function Tone Duration field identifies the duration, in ms, of the function tone. When dual function tones are set, both

tones are set to this duration. In most cases, this value is set to 40ms.

The range for this field is 0 to 999ms.

Function Tone Magnitude Field

The Function Tone Magnitude field identifies the level, in dBm, of the function tone.

The range for this field is -60 to 12dB.

FTone 1-16 Frequency Fields

The FTone 1-16 Frequency fields identify the value, in Hz, associated with each function tone burst. If the second value is set

at zero (0), no second function tone is sent. The standard function tones and their frequencies are shown in Table 7

The range for this field is 0 to 3200 Hz.

TABLE 7. Standard Function Tone Frequencies

Function Tone

Number

Frequency

(Hz)

Function Tone

Number

Frequency

(Hz)

1950

1850

1750

1650

1550

1450

1350

1250

1150

1050

950

850

750

650

550

450

F10

F11

F12

F13

F14

F15

F16

To define the frequencies and function tones, do the following:

1. From the links, select Tone Frequency & Durations.

The Tone Frequency and Durations window appears.

2. From the PTT Frequency drop down menu, select the PTT frequency (in Hz).

3. In the Guard Tone Duration field, enter the amount of time (in ms) the guard tone plays before the function tone.

4. In the Guard Tone Magnitude field, enter the level (in dBM) of the guard tone.

5. In the Hold Tone Magnitude field, enter the level (in dBM) of the hold tone summed with TX audio to keep the radio

in a transmit state.

6. In the Hold Tone Hangtime field, enter the amount of time (in ms) the hold tone continues after the release of the

PTT button.

7. In the Function Tone Duration field, enter the duration (in ms) of the function tone.

8. In the Function Tone Magnitude field, enter the level (in dBM) of the function tone.

114

Download from Www.Somanuals.com. All Manuals Search And Download.

Tone Frequency & Durations Window

9. In the Monitor Frequency field, enter the frequency (in Hz) of the function tone sent when the MON button on the

console is pressed.

NOTE: In the FTone 1-16 Frequency fields, the standard frequencies associated with each function tone are provided

in the first field for the function tone. To change the frequency for a function tone, enter the desired

frequency (in Hz) in the field provided.

10. In the frequency field, enter the desired frequency (in Hz).

11. Enter the desired frequency (in Hz) for the second function tone. An entry of zero (0) indicates no second function

tone is sent.

12. Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

13. From the links, select Save to EEPROM.

The Save Setup Parameters window appears.

14. Click Save Parameters.

The entries are saved to permanent memory.

115

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup Information

116

Download from Www.Somanuals.com. All Manuals Search And Download.

CHAPTER 5

Update Firmware

Telex VoIP Hardware firmware can be updated using TSM (Telex System Manager). A copy of TSM is available on the CD

included in the shipment with the VoIP hardware or can be downloaded from the Telex website at

www.telex.com/RadioDispatch/.

NOTE:

VoIP hardware includes the following Telex devices: IP-223, IP-2002, IP-1616, C-6200 and NEO-10.

TSM uses .tfb (Telex Firmware Binary) files to update VoIP firmware.

Install TSM

To install TSM, do the following:

1. Locate the setup.exe file on the Telex CD.

Download TSM from www.telex.com/Downloads/, see “Download Telex Firmware” on page 119.

2. Double-click setup.exe.

The Telex System Manager install window appears.

3. Click Next.

The Select Installation Folder window appears, see Figure 135.

117

Download from Www.Somanuals.com. All Manuals Search And Download.

FIGURE 135. Select Installation Folder

4. To specify an installation path for TSM, click Browse.

To accept the default folder location, leave the path entered in the Folder field

By default, TSM is installed at C:\Program Files\Telex Communications\Telex System Manager\.

5. To allow any user to access TSM, select Everyone.

To allow only one user to access TSM, select Just Me.

6. Click Next.

The Confirm Installation window appears, see Figure 136.

7. Click Next.

A Please Wait message appears. Once TSM is installed, a success message appears on the Confirm Installation

window.

8. Click Close.

FIGURE 136. Confirm Installation

118

Download from Www.Somanuals.com. All Manuals Search And Download.

Download Telex Firmware

When new firmware becomes available it is posted to our website. It can be downloaded at www.telex.com/Downloads/.

Check the website periodically for updated firmware.

FIGURE 137. Telex Website Firmware Downloads.

To download updated firmware, do the following:

1. Set the search criteria to Radio Dispatch & Signaling Equipment and Firmware, see Figure 137.

2. To sort the files by date, click the Date column heading.

3. Locate the updated firmware file for your device.

4. Click the filename.

The File Download window opens.

5. Save the file to your computer.

119

Download from Www.Somanuals.com. All Manuals Search And Download.

Update Firmware Tool Window

NAVIGATION: Selecting Firmware Update Tool from the Tools menu opens the Firmware Update Tool window shown in

Figure 138.

FIGURE 138. Firmware Update Tool

File Field

The File field is used to select a firmware file to upload to the VoIP hardware.

Firmware File Info Group Box

Device Type Field

The Device Type field displays the type of device supported by the currently selected file in the File field.

Firmware Version Field

The Firmware Version field displays the currently selected file’s firmware version.

Left Navigation Pane

The Left Navigation Pane displays all detected devices from the main dialog’s Device list with device types that match the

currently selected firmware files. Manually entered IP Addresses also appear in the navigation pane. Once the device is added,

it appears in the left navigation pane and is available for selection.

NOTE:

If the device you are updating does not automatically appear in the navigation pane, manually enter the IP

Address in the Manual Entry field.

120

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Entry Field

The Manual Entry field is used to enter the VoIP hardware’s IP Address to add to the left navigation pane.

Username Field

The Username field is used to enter the administrator’s username.

NOTE:

When updating firmware, admin is the only administrator’s username.

Password Field

The Password field is used to enter the administrator’s password, if one is required.

Write Firmware Button

The Write Firmware button is used to begin the upload process. Once the button is selected, the file specified in the File field

is uploaded to the VoIP hardware.

Close Button

The Close button is used to close the window.

Upload VoIP Hardware Firmware

Once TSM is installed and your new .tfb file is downloaded, you are ready to upload the VoIP hardware’s firmware.

To upload the VoIP hardware’s firmware, do the following:

1. Click the TSM shortcut on your desktop.

From your taskbar, click Start|Programs|Telex Communications|Telex System Manager.

The Telex System Manager window opens.

2. Click Tools|Firmware Update

The Firmware Update Tool opens.

3. To locate the .tfb file for upload, click the folder icon

The Open window appears.

4. Select the.tfb file you want to upload.

The file is highlighted.

5. Click Open.

The selected file appears in the File field.

NOTE: If the device does not appear in the list, enter the VoIP hardware’s IP Address in the Manual Entry field

and click the Add button . The IP Address appears in the left navigation pane.

6. In the left navigation pane, select the device’s IP Address.

The Write Firmware button is active.

7. Click the Write Firmware button.

Firmware update messages are shown in the Status column which provides feedback on the firmware update

progress. Once the progress reaches 100%, the firmware is updated.

NOTE: If an error occurs, the Progress column is reset and an error message appears in the Status column.

121

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: Once the firmware is uploaded, the device resets.

FIGURE 139. Firmware Update Tool— Success Messages

8. Click Close.

The dialog window closes.

9. Click Close.

To access the webpage directly from the Firmware Update Tool window, do the following:

1. Right-click the device’s entry.

The Flyout menu appears.

2. From the context menu, click Webpage.

The Connect To window opens.

3. In the User Name field, enter a user name.

4. In the Password field, enter a password.

5. Click OK.

The Web Browser’s Configuration Welcome window opens.

122

Download from Www.Somanuals.com. All Manuals Search And Download.

IP-223 Settings - Quick Reference

I/O Connectors

Connector Description

J18

Power IN

Serial port

Radio/Line 1

Radio/Line 2

Display Header

Handset Jack

Ethernet port

J31

J66

Adjustments

Signal

Line 1

R175

RV5

Test point

TP13

Line 2

R110

RV1

Test point

TP1

RX Pre-amp

RX Compressor

TP12

TP3

TX Audio out

R47

TP15

R61

TP5

TX Monitor IN

R390

R50

TP13

TP7

R391

R53

TP1

(Not available in 750630 Rev A)

CTCSS out

TP10

123

Download from Www.Somanuals.com. All Manuals Search And Download.

Jumper Settings

PCB 750743 or PCB 750630 revision F

Line 1

Jumper Setting

Line 2

J35

"A" = RS232 serial data, "B" = TTL

J26

PCB 750743 or PCB 750630 revision C, D, E, and F

Line 1

J33, J34

J16, J21

J14

Jumper Setting

Line 2

J5, J6

J19, J20

J24

2 or 4 Wire, "A" = 2-wire, "B" = 4-wire

RX Input, "A" = Single ended, "B" = Balanced

RX Input Impedance, “A” = 600, “B” = 8 and Center = 10Kohm

J25, J28,

J29

J3, J9, J11 TX Output, “A” = Single ended, “B” = Balanced

J13

TX Output Level, “A” = Low, “B” = High

Digital I/O Pull-up Voltage, “A” = +5, “B” = +12

TX Output Impedances: “B” = 600 ohms

J27

J30

J17, J22

J10, J15

(J10), J15

J10, (J15)

J10, J15

(J17), J22 (“A”) and “B” = 1.2K ohms

J17, (J22) “A” and (“B”) = 1.8K ohms

J17, J22

“A” = 2.4K ohms

PCB 750630 revision A

Line 1

Jumper Setting

Line 2

J33, J34

2 or 4 Wire, “A” = 2-wire, “B” = 4-wire

RX Input, “A” = Single ended, “B” = Balanced

RX Input Impedances: “B” = 10K ohms

J5, J6

J15, J16,

J21

J19, J20,

J22

J14, J23

J24, J17

(J14), J23 (“A”) and “B” = 600 ohms

(J23), J14 (“A”) and “B” = 8 ohm speaker

J3, J9,

(J24), J17

(J17), J24

J25, J26,

J28, J29

TX Output, “A” =Single ended, “B” = Balanced

J10, J11

J13

TX Output Level, “A” = Low, “B” High

J27

J30

Digital I/O Pull-up Voltage, “A” = +5, “B” = +12

124

Download from Www.Somanuals.com. All Manuals Search And Download.

Jumper Locations

FIGURE 140. Jumper Locations

125

Download from Www.Somanuals.com. All Manuals Search And Download.

126

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A

Additional Resources

Below is a compilation of resources ranging from the technology used in Radio Dispatch products, as well as application

guides describing how to configure the radio dispatch products with many of the radios used with those products.

NOTE:

Because white papers and application guides are always being written and posted to this site, please visit

http://www.telex.com/RadioDispatch/Default.aspx, and then click Downloads, for the most current list of

publication offerings.

FILE

Application Guides

AN-VEGA-10

Moto XTL-5000

Motorola XTL - 5000 Radios to 223 Series Adapter Panel

This application note is intended to show how to assemble a cable and setup the hardware of

different 223 series adaptor panels (TRA223, DSP223 and IP223) to a Motorola XTL-5000 series

mobile radio.

AN-VEGA-7

Cross Band

Repeater

Creating Cross Band Repeaters or Extended Radio Coverage Using

IP-223s

This application guide is intended to show how to create a cross band repeater or extend coverage

using IP-223s in either a LAN (Local Area Network) or WAN (Wide Area Network).

AN-VEGA-1

Kenwood

Fleetsync

Kenwood Radio - Series 80, 90, and 150/180 To IP-223

This application guide is intended to show how to assemble the cable and setup the hardware of the

IP-223 for channel change and Fleetsync applications using Kenwood radios.

AN-VEGA-4

223 EFJ5300

EF Johnson - Series 5300 radio to the 223 Series Adaptor Panels

This application guide is intended to show how to assemble a cable and setup the hardware of

different 223 series adaptor panels (TRA223, DSP223 and IP223) to the EF Johnson 5300 mobile

radio.

127

Download from Www.Somanuals.com. All Manuals Search And Download.

AN-VEGA-19

223 - Relm RM

Series

RELM - RM Series Radios to 223 Series Adaptor Panels

This application guide is intended to show how to assemble a cable and setup hardware of different

223 series adaptor panels (TRA223, DSP223, and IP223) to a Relm RM series mobile radio.

AN-VEGA-18

223 Vertex VX

4100-4200

Vertex Standard - VX-4100/4200 Series Radios to 223 Series Adaptor

Panels

This application guide is intended to show how to assemble a cable and setup hardware of different

223 series adaptor panels (TRA223, DSP223, and IP223) to the VX-4100/4200 series mobile radio.

AN-VEGA-15

Datron - Guardian Series Mobile to 223 Series Adaptor Panels

223 - Datron

Guardian

This application guide is intended to show how to assemble a cable and setup hardware of different

223 series adaptor panels (TRA223, DSP223, IP223) to the Datron Guardian Mobile radio.

AN-VEGA-13

Telex Radio Dispatch ANI Capabilities

ANI Capabilities

This application guide is intended to educate the reader on Automatic Numerical Identification (ANI)

and, specifically, the support for ANI within the Radio Dispatch products.

AN-VEGA-11

Sepura

Sepura - SRM2000 - IP223 Interface

This application guide is intended to describe the interface between the IP223 and the Sepura 2000

Mobile TETRA radio. The contents include: physical connections, diagrams, IP-233 setup, SRM2000

setup, and C-Soft PC console configuration.

AN-VEGA-9

Motorola - CDM/GM/PRO Series Radios to 223 Series Adaptor Panels

223 Motorola

CDM-Pro Series

This application guide is intended to show how to assemble a cable and setup the hardware of

different 223 series adaptor panels (TRA223, DSP223, and IP223) to a Motorola CDM, GM, PRO

series mobile radio.

Motorola - Radius, M10, M100, M120, M130, M200, GM300, SM50, SM120,

and Maxtrac 100/300 Series Radios to TRA223 & DSP223 Series Adaptor

Panels

AN-VEGA-5

DSP-TRA

Motorola Mobiles

This application guide is intended to show how to assemble a cable and setup the hardware of the

TRA223 and DSP223 for single channel control to the following Motorola radios: Radius, M10, M100,

M120, M130, M200, GM300, SM50, SM120 and Maxtrac 100/300.

AN-VEGA-6

IP-Motorola

Mobiles

Motorola - Radius, M10, M100, M120, M130, M200, GM300, SM50, SM120,

and Maxtrac 100/300 Series Radios to IP223 Series Adaptor Panels

This application guide is intended to show how to assemble a cable and setup the hardware of the

IP223 for single channel control to the following Motorola radios: Radius, M10, M100, M120, M130,

M200, GM300, SM50, SM120 and Maxtrac 100/300.

128

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Resources

AN-VEGA-17

IP223 Relm GMH

RELM - GMH Radios to IP-223 Adaptor Panels

This application guide is intended to show how to assemble a cable and setup the hardware of the

IP-223 adaptor panel to a Relm GMH series mobile radio.

AN-VEGA-12

iDEN-IP223 to

Tone

iDEN Radio Control on Legacy Tone Systems using IP-223s

This application guide is intended to show how to configure and connect the Telex/Vega IP-223,

NI223 and an iDEN radio to a legacy tone control system and provide direct connect to an operator.

AN-VEGA-20

Motorola - MCS2000 Radios to 223 Series Adaptor Panels

223 Moto

MCS2000

This application guide is intended to show how to assemble a cable and setup the hardware of

different 223 series adaptor panels (TRA223, DXP223, and IP223) to a Motorola MCS2000 series

mobile radio.

AN-VEGA-22

223 - ICOM

F121-221

ICOM - IC-F121/221 Series Radio to 223 Series Adaptor Panels

This application guide is to show how to assemble a cable and setup the hardware of different 223

series adaptor panels (TRA223, DSP223, and IP223) to the ICOM F121/221 mobile radio.

AN-VEGA-23

Kenwood - TK-6110 Series Radio to 223 Series Adaptor Panels

223 - Kenwood

TK6110

This application guide is to show how to assemble a cable and setup the hardware of different 223

series adaptor panels (TRA223, DSP223, and IP223) to a Kenwood TK-3110 series mobile radio.

White Papers

IP White Paper

IP Radio System Application Guide (White Paper)

This white paper is intended to introduce potential customers to the options and technologies

available from Telex Vega for the remote control and monitoring of multiple radio channels. While the

subject of tone control will be discussed from a historical point of view, the focus of this document is

Radio control over Internet Protocol, or RoIP. RoIP is a subset of the larger entity, known as Voice

over IP or VoIP throughout this document.

An Introduction

To IP

An Introduction to IP-Based Radio Dispatch (White Paper)

This white paper is intended to be an high-level introduction to the IP-based Radio Dispatch

technology. Some topics discussed in this paper are: VoIP, RoIP, TCP/IP, UDP/IP, and other IP-

based technologies.

129

Download from Www.Somanuals.com. All Manuals Search And Download.

130

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX B

CTCSS Tone Frequency Table

TABLE 8. CTCSS Tone Frequencies

Tone

Number

Freq.

(Hz)

Tone

Number

Freq.

(Hz)

Tone

Number

Freq.

(Hz)

Tone

Number

Freq.

(Hz)

33.0

35.4

36.6

37.9

39.6

44.4

47.5

49.2

51.2

53.0

54.9

56.8

58.8

63.0

67.0

69.4

71.9

74.4

123.0

127.3

131.8

136.5

141.3

146.2

151.4

156.7

159.8

162.2

165.5

167.9

171.3

173.8

177.3

179.9

183.5

186.2

189.9

192.8

196.6

199.5

203.5

206.5

210.7

218.1

225.7

229.1

233.6

241.8

250.3

254.1

77.0

79.7

82.5

85.4

88.5

91.5

94.8

97.4

100.0

103.5

107.2

110.9

114.8

118.8

131

Download from Www.Somanuals.com. All Manuals Search And Download.

132

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX C

Digital Output Table

TABLE 9. Digital Output Values

Digital Output Table

TABLE 9. Digital Output Values

133

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE 9. Digital Output Values

117

118

119

120

121

122

123

124

125

126

127

128

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

134

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX D

Tone Frequency Table

TABLE 10. Supported Radio Dispatch Tone Frequencies

European Tone Frequencies in Hz

Motorola

TONE 0

TONE 1

TONE 2

TONE 3

TONE 4

TONE 5

TONE 6

TONE 7

TONE 8

TONE 9

GROUP

TONE

2400 2400

1060 1060

815

882

954

2400 2200 2200 1981 1981 1981 1981

979.8

903.1

832.5

767.4

707.4

652.0

601.0

554.0

510.7

470.8

1633

631

697

770

852

941

600

637.5

787.5

937.5

1060

970

1060 1060

1160 1160

1400 1270 1270 1358 1358 1358 1358

970

1124

741

882

1160

1197

1270 1270 1032 1270

1400 1400 1117

1275 1275 1275 1275

1023 1087.5

1164 1237.5

1305 1387.5

1530 1530 1209 1530 1400 1400 1446 1446 1446 1446

1670 1670 1308 1670 1530 1530 1540 1540 1540 1540

1830 1830 1415 1830 1670 1670 1640 1640 1640 1640

2000 2000 1531 2000 1830 1830 1747 1747 1747 1747

2200 2200 1657 2200 2000 2000 1860 1860 1860 1860

1040 1446 1537.5

1209 1587 1687.5

1336 1728 1837.5

1477 1869 1987.5

825/

885

2800

810

885

810

740

680

970

2600

1939

2270

970

810

825

886

2400

930

1050 1055

930 930

2400 2247

2151

2292

2010

2292

740

RESET

TONE

970

2098 2800 2600 2600 2247

885

2457

1792 2600 2400 2400

680 680

885

856

991

2110

2400

991

2110 1062.9 1805

REPEAT

TONE

2600

680

2110

459

487.5

1055 2400 1995 1091

1995 1091

135

Download from Www.Somanuals.com. All Manuals Search And Download.

136

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

137

Download from Www.Somanuals.com. All Manuals Search And Download.

Taylor Scale 3852 User Manual
TDK Network Card HHM Series HHM1713E2 User Manual
Tiffen Carrying Case F 10 User Manual
Toshiba Printer B 480 QP User Manual
TP Link Network Card TL PA8010P User Manual
Transcend Information Computer Drive MS User Manual
Tricity Bendix Cooktop SB431 User Manual
Tripp Lite Power Supply AGOM7594 User Manual
Viking Ventilation Hood F1570F User Manual
Vizio Car Satellite TV System E4011 A2 User Manual