TP Link Network Router TL SG1008P User Manual

User Guide  
TL-SG1008P  
8-Port Gigabit Desktop Switch with 4-Port PoE  
Rev˖1.0.0  
7106504137  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COPYRIGHT & TRADEMARKS  
Specifications are subject to change without notice.  
is a registered trademark of TP-LINK  
TECHNOLOGIES CO., LTD. Other brands and product names  
are trademarks or registered trademarks of their respective  
holders.  
No part of the specifications may be reproduced in any form or  
by any means or used to make any derivative such as  
translation, transformation, or adaptation without permission  
from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012  
TP-LINK TECHNO- LOGIES CO., LTD. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
This equipment has been tested and found to comply with the  
limits for a Class A digital device, pursuant to part 15 of the FCC  
Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is  
operated in  
a
commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual,  
may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to  
cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions:  
1) This device may not cause harmful interference.  
2) This device must accept any interference received,  
including interference that may cause undesired operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Any changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s authority  
to operate the equipment.  
CE Mark Warning  
This is a class A product. In a domestic environment, this  
product may cause radio interference, in which case the user  
may be required to take adequate measures.  
SAFETY NOTICES  
Cautions  
Do not use this product near water, for example, in a wet  
basement or near a swimming pool.  
Avoid using this product during an electrical storm. There may  
be a remote risk of electric shock from lightning.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENT  
Package Contents ...................................................... 1  
Chapter 1. Introduction of the Product .......................... 2  
1.1  
1.2  
1.3  
Overview of the Product ...................................... 2  
Convention............................................................ 3  
Features................................................................. 3  
Chapter 2. Installation................................................. 4  
2.1  
2.2  
Mounting the Switch on a Desk........................... 4  
Power On............................................................... 4  
Chapter 3. Identifying External Components .................. 5  
3.1  
3.2  
Front Panel............................................................ 5  
Rear Panel ............................................................. 7  
Appendix A: Specifications.......................................... 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Package Contents  
The following items should be found in your box:  
Z
One TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port  
PoE  
Z
Z
Z
One DC Power Adapter  
Four rubber cushions to be used under the Switch  
This User Guide  
Note  
Make sure that the box contains the above items. If any of the  
listed items are damaged or missing, please contact your  
distributor.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1. Introduction of the Product  
Thank you for choosing the TL-SG1008P 8-Port Gigabit Desktop  
Switch with 4-Port PoE.  
1.1 Overview of the Product  
The TL-SG1008P 8-Port Gigabit Desktop Switch with 4-Port PoE  
provides the seamless network connection, which integrates  
1000Mbps Gigabit Ethernet, 100Mbps Fast Ethernet and  
10Mbps Ethernet network capabilities.  
This PoE Switch is also a Power Sourcing Equipment (PSE*).  
Four of the eight Auto-Negotiation RJ45 ports (ports1~4) on the  
Switch support Power over Ethernet (PoE*) function, which can  
automatically detect and supply power with those IEEE802.3af-  
compliant powered devices (PDs*).  
*PSE: A device (switch or hub for instance) that will provide  
power in a PoE setup.  
*PoE: This technology describes a system to transmit electrical  
power, along with data, to remote devices over standard  
twisted-pair cable in an Ethernet network.  
*PD:  
A device powered by a PSE and thus consumes energy.  
Examples include powering IP telephones, wireless LAN  
access points, network cameras, network hubs, embedded  
computers etc.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.2 Convention  
The Switch or TL-SG1008P mentioned in this User Guide  
stands for TL-SG1008P 8-Port Gigabit Desktop Switch with  
4-Port PoE without any explanation.  
1.3 Features  
Z
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab,  
IEEE802.3x, IEEE802.3af standards  
Z
8 10/100/1000Mbps Auto-Negotiation RJ45 ports with 4  
ports supporting PoE function (ports1~4), all of them support  
Auto-MDI/MDIX  
Z
Z
Z
Z
Supports PoE power up to 15.4W for each PoE port  
Supports PoE power up to 53W for PoE ports  
Supports PoE IEEE802.3af compliant PDs  
Supports IEEE802.3x flow control for Full-duplex Mode and  
backpressure for Half-duplex Mode  
Z
Z
Z
8K entry MAC address table of the TL-SG1008P with auto-  
learning and auto-aging  
LED indicators for monitoring Power, Link/Act, Speed and  
PoE Status  
External power adapter supply  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2. Installation  
During the installation procedure, please only use the  
accessories equipped with the Switch.  
2.1 Mounting the Switch on a Desk  
To install the Switch, please follow the steps:  
1) Place the Switch on a flat desk.  
2) Remove the adhesive backing papers from the rubber  
cushions.  
3) Turn over the Switch and attach the supplied four rubber  
cushions to the recessed areas on the bottom at each  
corner of the Switch.  
Note  
1) Please avoid any heavy thing placed on the Switch.  
2) Make sure the power is off before unplugging the power  
adapter.  
2.2 Power On  
The TL-SG1008P Switch can be used with DC power supply.  
Powering on the Switch, it will automatically initialize and its LED  
indicators will respond as follows:  
1) Firstly, the Power LED indicator will light up.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) Then, the 1000Mbps and Link/Act LED indicators will flash  
momentarily for one second, which represents a resetting of  
the system.  
Note  
If the LED indicators don’t respond as described above, please  
check the power supply and its connection.  
Chapter 3. Identifying External Components  
This Chapter describes the front panel, rear panel and LED indi-  
cators of the Switch.  
3.1 Front Panel  
Figure 3-1 TL-SG1008P Switch Front Panel  
The Switch’s LEDs are located on the front panel.  
Name  
Status Indication  
On  
(green)  
The Switch is powered on.  
The Switch is powered off.  
Power  
Off  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Name  
Status Indication  
On  
(green)  
There is a PoE PD connected to the port, which  
supply power successfully.  
Flashing  
(green)  
The PoE power circuit may be in short or the  
power current may be overloaded.  
PoE ports  
(ports1~4)  
No PD is connected to the corresponding port, or  
no power is supplied according to the power  
limits of the port.  
Off  
The power of all the connected PoE ports is  
>=46W. No power may be supplied if additional  
PDs are connected.  
On  
(red)  
Flashing  
(red)  
The power of all the connected PoE ports is  
>=53W.  
PoE MAX  
The power of all the connected PoE ports is  
<46W, or there is no PD connected to the  
corresponding port.  
Off  
On  
(green)  
A valid link is established on the port.  
Link/Act  
(ports1~8)  
Flashing  
(green)  
The corresponding port is transmitting or  
receiving data.  
No device is connected to the corresponding  
port.  
Off  
On  
(green)  
There is a 1000Mbps device connected to the  
corresponding port.  
1000Mbps  
(ports1~8)  
There is a 10/100Mbps device connected to the  
corresponding port, or there is no device  
connected to the corresponding port.  
Off  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
If all PoE PDs power consumption is >= 53W, a priority* will be  
arranged among the PoE ports like port-1 = port-2 = port-3 >  
port-4, then the system will cut off the power of the  
lowest-priority port.  
*Priority: This function will help protect the system when the  
system power is overloaded. For example, Port 1, 2  
and 4 is using 15.4W (maximum power for per port is  
15.4W); the system power is 46.2W in total. If there is  
an additional PD inserted to Port 3 with 10W, and  
then the system will cut off the power of Port 4  
because of the overloaded power, this means Port 1, 2  
will use 15.4W, and Port3 will use 10W, no power  
will be supplied to Port 4.  
3.2 Rear Panel  
Figure 3-2 TL-SG1008P Switch Rear Panel  
The following parts are located on the rear panel:  
Z
Power (48V): 48V indicates the input voltage of the power  
adapter provided with this TL-SG1008P Switch. The Power  
socket is where you will connect the power adapter.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Z
PoE Ports (1-4): These ports support PoE function which  
integrates power and data onto one Ethernet cable. Once  
the device you connect to the Switch is identified, the Switch  
will supply power through the PoE port, and then you can  
use it as  
a
10/100/1000Mbps Auto-Negotiation RJ45  
Ethernet port. The working status can be indicated by the  
corresponding LEDs on the front panel.  
Z
Ethernet Ports (1-8): Besides the 4 PoE ports, the  
TL-SG1008P Switch is also equipped with the other four  
10/100/1000Mbps Auto-Negotiation RJ45 ports without PoE  
function. Once the network devices are connected to these  
8 ports through the network cable, the Switch will make  
them plug and play according to the Auto-MDI/MDIX  
detection. The working status can be indicated by the  
corresponding LEDs on the front panel.  
Note  
Make sure the PDs you connected to the Switch are compliant  
with IEEE802.3af.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix A: Specifications  
General  
IEEE802.3, IEEE802.3u, IEEE802.3ab  
IEEE802.3x, IEEE802.3af  
Standard  
Protocol  
CSMA/CD  
Ethernet: 10Mbps (Half Duplex)  
20Mbps (Full Duplex)  
Data Transfer Rate  
Fast Ethernet: 100Mbps (Half Duplex)  
200Mbps (Full Duplex)  
Gigabit Ethernet: 2000Mbps (Full Duplex)  
10Base-T:  
UTP category 3, 4, 5 cable (maximum 100m)  
EIA/TIA-568 100ꢀ STP (maximum 100m)  
100Base-TX:  
UTP category 5, 5e cable (maximum 100m)  
EIA/TIA-568 100ꢀ STP (maximum 100m)  
Network Media(Cable)  
1000Base-T:  
UTP category 5, 5e cable (maximum 100m)  
EIA/TIA-568 100ꢀ STP (maximum 100m)  
8 10/100/1000Mbps Auto-Negotiation RJ45  
ports with PoE enabled (ports1~4)  
Number of Ports  
Power+: pin 3 & pin 6  
Power -: pin 1 & pin 2  
PoE Power on RJ45  
Power, Link/Act, 1000Mbps, PoE Status,  
PoE MAX  
LEDs  
Transfer Method  
Store-and-Forward  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAC Address Learning Automatically learning, automatically aging  
10Base-T: 14880pps/Port  
Frame Filter Rate  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
10Base-T: 14880pps/Port  
Frame Forward Rate  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
Environmental and Physical  
5.8 Watts (max. no PD connected)  
58.8 Watts (max. with 53W PD connected)  
Power Consumption  
Operating Temperature 0 ~40ć (32 ~104̧)  
Storage Temperature  
Operating Humidity  
Storage Humidity  
-40 ~70ć (-40 ~158̧)  
10%~90% non-condensing  
5%~90% non-condensing  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Teledyne Marine Radio HPM 760 User Manual
Toastmaster Oven SC 14 User Manual
Traulsen Refrigerator RHT132EUT FHS User Manual
TRENDnet Network Router 108Mbps High Speed 80211g Wireless Access Point User Manual
Triarch Indoor Furnishings 39661 User Manual
Underwater Kinetics Work Light SL4 eLED User Manual
VBrick Systems Home Theater Server ETV v41 User Manual
Vizio Blu ray Player XWR100 User Manual
Vornado Humidifier EVAP2 User Manual
VTech Cordless Telephone LS6191 LS6191 13 LS6191 15 LS6191 16 LS6191 17 User Manual