Teledyne Marine Radio HPM 760 User Manual

HPM-760s Installation  
HPM-760s Installation  
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and  
evacuation port is provided for system connection. VCR and KF stem terminations are also available.  
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and  
evacuation port is provided for system connection. VCR and KF stem terminations are also available.  
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem  
threads of the transducer. Hand thread transducer  
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem  
threads of the transducer. Hand thread transducer  
into vacuum system, until joint is finger tight.  
into vacuum system, until joint is finger tight.  
Tighten transducer module completely using  
a
Tighten transducer module completely using  
a
wrench on the hexagonal portion of the stem.  
wrench on the hexagonal portion of the stem.  
Do not grip instrument case to tighten; this will  
result in permanent damage to transducer assem-  
bly. When the 760s is purchased independently of  
the power supply/display, a connector is provided  
so that the transducer can be connected as detailed  
in the figure.  
Do not grip instrument case to tighten; this will  
result in permanent damage to transducer assem-  
bly. When the 760s is purchased independently of  
the power supply/display, a connector is provided  
so that the transducer can be connected as detailed  
in the figure.  
TRANSDUCER PIN-OUT  
TRANSDUCER PIN-OUT  
PIN 1................Signal Output (COM)  
PIN 2................Signal Output (POS)  
PIN 3................15-30 VDC Input (COM)  
PIN 4................15-30 VDC Input (POS)  
PIN 1................Signal Output (COM)  
PIN 2................Signal Output (POS)  
PIN 3................15-30 VDC Input (COM)  
PIN 4................15-30 VDC Input (POS)  
Manual may be obtained at:  
Manual may be obtained at:  
I S O 9 0 0 1  
I S O 9 0 0 1  
Quick Start Guide_166-082010  
Quick Start Guide_166-082010  
C
E
R
T
I
F
I
E
D
C
E
R
T
I
F
I
E
D
HPM-760s Installation  
HPM-760s Installation  
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and  
Figure below shows the Hastings piezo vacuum transducer. A standard 1/8” NPT male stem and  
evacuation port is provided for system connection. VCR and KF stem terminations are also available.  
evacuation port is provided for system connection. VCR and KF stem terminations are also available.  
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem  
threads of the transducer. Hand thread transducer  
When installing transducers with threaded stem, apply an approved vacuum sealant to the stem  
threads of the transducer. Hand thread transducer  
into vacuum system, until joint is finger tight.  
into vacuum system, until joint is finger tight.  
Tighten transducer module completely using  
a
Tighten transducer module completely using  
a
wrench on the hexagonal portion of the stem.  
wrench on the hexagonal portion of the stem.  
Do not grip instrument case to tighten; this will  
result in permanent damage to transducer assem-  
bly. When the 760s is purchased independently of  
the power supply/display, a connector is provided  
so that the transducer can be connected as detailed  
in the figure.  
Do not grip instrument case to tighten; this will  
result in permanent damage to transducer assem-  
bly. When the 760s is purchased independently of  
the power supply/display, a connector is provided  
so that the transducer can be connected as detailed  
in the figure.  
TRANSDUCER PIN-OUT  
TRANSDUCER PIN-OUT  
PIN 1................Signal Output (COM)  
PIN 2................Signal Output (POS)  
PIN 3................15-30 VDC Input (COM)  
PIN 4................15-30 VDC Input (POS)  
PIN 1................Signal Output (COM)  
PIN 2................Signal Output (POS)  
PIN 3................15-30 VDC Input (COM)  
PIN 4................15-30 VDC Input (POS)  
Manual may be obtained at:  
Manual may be obtained at:  
I S O 9 0 0 1  
I S O 9 0 0 1  
Quick Start Guide_166-082010  
Quick Start Guide_166-082010  
C
E
R
T
I
F
I
E
D
C
E
R
T
I
F
I
E
D
Download from Www.Somanuals.com. All Manuals Search And Download.  

Texas Instruments Stereo Amplifier TPA2012D2 User Manual
Timex Clock Radio T433 User Manual
Toastmaster Kitchen Grill GRB48B User Manual
Top Innovations Iron SF 717 User Manual
Tricity Bendix Refrigerator TB 56 R User Manual
Tricity Bendix Washer AW 700 User Manual
Univex Lawn Mower 3593 User Manual
Viking Ventilation Hood DEV900 User Manual
Vinotemp Refrigerator VINO4500DS User Manual
Vivotek Security Camera FD8131 User Manual