OWNER’S
MANUAL
COLOR TV/DVD
(20 inch)
SC520FDF
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-242-7158.
Please read before using this equipment
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD I N
WI RE
GROUND
CL AMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRI C
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC
-
NATIONAL ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
13. Outdoor Antenna grounding - If an outside antenna or
cable system is connected to the unit, be sure the anten-
na or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect
to proper grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an antenna dis-
charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrode.
(Fig. A)
19. Damage Requiring Service - Unplug this unit from the
wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into the
unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified techni-
cian to restore the unit to its normal operation.
14. Lightning - For added protection for this unit receiver
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system.
This will prevent damage to the unit due to lightning and
power-line surges.
e. If the unit has been dropped or damaged in any way.
f. When the unit exhibits a distinct change in performance,
this indicates a need for service.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used replace-
ment parts specified by the manufacturer that have the
same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, injury to
persons or other hazards.
21. Safety Check - pon completion of any service or repairs
to this unit, ask the service technician to perform routine
safety checks to determine that the unit is in proper
operating condition.
16. Overloading - Do not overload wall outlets and exten-
sion cords as this can result in a risk of fire or electric
shock.
17. Object and Liquid Entry - Never push objects of any
kind into this unit through openings as they may touch
dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the unit.
22. Heat - This unit product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
18. Servicing - Do not attempt to service this unit yourself
as opening or removing covers may expose you to dan-
gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
- 3 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
LASER SAFETY
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public perfor-
mance and lending of discs are prohibited.
This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise autho-
rized by Macrovision. Reverse engineering or dis-
assembly is prohibited.
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to ser-
vice this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
FCC WARNING- This equipment may gener-
ate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction man-
ual. The user could lose the authority to oper-
ate this equipment if an unauthorized change
or modification is made.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This Class B digital apparatus complies with
Canadian ICES-003.
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
Batteries should never be thrown away or inciner-
ated but disposed of in accordance with your local
regulations concerning chemical wastes.
3) Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
The serial number of this product may be found on the back of the unit. No other unit has the same serial
number as yours. You should record the number and other vital information here and retain this book as a per-
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 4 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
LOCATION
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a unit which has
moisture, it may damage the DVD and the unit.
Therefore when the condensation occurs inside the
unit, turn the unit on and allow at least 2 hours for the
unit to dry out.
For safe operation and satisfactory performance of
your unit, keep the following in mind when selecting
a place for its installation:
Shield it from direct sunlight and keep it away from
sources of intense heat.
•
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top or bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
•
•
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some head-
ings and notes in this manual, with the following
meanings.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the unit near strong magnetic fields.
Avoid moving the unit to locations where tempera-
•
•
•
•
TV
: Description refers to TV operation (in the TV mode).
ture differences are extreme.
DVD-V
Be sure to remove disc and unplug the AC power
cord from the outlet before carrying the unit.
•
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
CD
ELECTRICAL SHOCK AND FIRE
: Description refers to playback of Audio CDs
(in the DVD mode).
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug.
If by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
•
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
•
Do not put your fingers or objects into the unit disc
loading tray.
•
Do not place anything directly on top of the unit.
•
SUPPLIED ACCESSORIES
Remote Control Unit
Batteries
Owner’s Manual
Owner's Manual
( NE207UD )
2 AA Batteries
( 1EMN20326 )
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our
help line mentioned on the front page.
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators
(Splitter). Contact your local electronics store for these items.
•
•
- 5 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
DVD SECTION
C IMPORTANT SAFEGUARDS . . . . .2
C CHANGING THE DVD SET UP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .26
C PRECAUTIONS . . . . . . . . . . . . . . . .4
C ABOUT THE DISCS . . . . . . . . . . . .19
PLAYABLE DISCS . . . . . . . . . . . .19
UNPLAYABLE DISCS . . . . . . . . . .19
CUSTOM MENU . . . . . . . . . . . . . .26
LANGUAGE SETTING . . . . . . . .26
DISPLAY SETTING . . . . . . . . . .27
AUDIO SETTING . . . . . . . . . . . .27
PARENTAL CONTROL . . . . . . . .28
OTHER SETTINGS . . . . . . . . . . .28
INITIALIZE . . . . . . . . . . . . . . . . . .28
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
C PLAYING A DISC . . . . . . . . . . . . . .20
BASIC PLAYBACK . . . . . . . . . . . .20
GENERAL FEATURES . . . . . . . . .20
DISC MENU . . . . . . . . . . . . . . . . .20
TITLE MENU . . . . . . . . . . . . . . . . .20
RESUME . . . . . . . . . . . . . . . . . . . .21
PAUSE . . . . . . . . . . . . . . . . . . . . . .21
STEP BY STEP PLAYBACK . . . . .21
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C SUPPLIED ACCESSORIES . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C TROUBLESHOOTING GUIDE . . .29
C MAINTENANCE . . . . . . . . . . . . . . .32
DISC HANDLING . . . . . . . . . . . . .32
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .8
C SPECIFICATIONS . . . . . . . . . . . . .33
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .34
C WARRANTY . . . . . . . . . . .Back Cover
FAST FORWARD /
FAST REVERSE . . . . . . . . . . . . . .21
C PREPARATION FOR USE . . . . . . .10
SLOW FORWARD /
SLOW REVERSE . . . . . . . . . . . . . .21
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .10
ZOOM . . . . . . . . . . . . . . . . . . . . . .21
CONNECTING TO FRONT A/V
C SEARCH FUNCTION . . . . . . . . . . .22
TRACK SEARCH . . . . . . . . . . . . .22
TITLE / CHAPTER SEARCH . . . .22
TIME SEARCH . . . . . . . . . . . . . . .22
MARKER SETUP SCREEN . . . . . .22
INPUT JACKS . . . . . . . . . . . . . . . .11
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS (for DVD)11
CONNECTING TO A DOLBY
DIGITAL DECODER (for DVD) . .12
INSTALLING THE BATTERIES . .12
C
SPECIAL PLAYBACK FUNCTION . .23
REPEAT . . . . . . . . . . . . . . . . . . . . .23
PROGRAM . . . . . . . . . . . . . . . . . . .23
RANDOM PLAYBACK . . . . . . . . .23
TV SECTION
C TV OPERATION AND SETTINGS .13
WATCHING A TV PROGRAM . . .13
DEGAUSSING . . . . . . . . . . . . . . . .13
PICTURE CONTROL . . . . . . . . . . .13
SLEEP TIMER . . . . . . . . . . . . . . . .14
CLOSED CAPTION SYSTEM . . . .14
CHANNEL SET UP . . . . . . . . . . . .15
V-CHIP SET UP . . . . . . . . . . . . . . .16
TV RATING SET UP . . . . . . . . .16
MPAA RATING SET UP . . . . . .17
CHANGE ACCESS CODE . . . . .17
MENU LANGUAGE . . . . . . . . . . .17
C CHANGING THE SETTINGS . . . .24
SUBTITLE LANGUAGE . . . . . . . .24
AUDIO LANGUAGE . . . . . . . . . . .24
STEREO SOUND MODE . . . . . . . .24
CAMERA ANGLE . . . . . . . . . . . . .24
BLACK LEVEL SETTING . . . . . . .24
VIRTUAL SURROUND . . . . . . . . .25
C
THE ON-SCREEN INFORMATION . .25
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .18
- 6 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
TV Mode
Infrared remote control
Trilingual on screen TV setup display selectable
in English, Spanish or French
181 channel capability PLL frequency synthesiz-
er tuner with direct station call (A converter may
be necessary to view scrambled cable channels.)
Closed Caption Decoder – You may view special-
ly labeled (cc) TV programs, movies, news, etc.
with either a dialogue caption or text display added
to the program.
Auto power off system – If there is no air signal
•
•
•
input from the antenna terminal and no operation
for 15 minutes, the unit will turn itself off automat-
ically.
Sleep timer – Allows you to have the unit auto-
matically turn off at a desired time.
•
•
•
V-CHIP – Enables parents to prevent their children
from watching inappropriate material on TV.
•
DVD Mode
¡Dolby Digital sound
¡Parental lock
This unit can handle Dolby Digital surround sound
having 5.1 channels when connected to a Dolby
Digital decoder.
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This unit automatically detects if the loaded disc is
DVD or Audio CD.
¡Still/fast/slow/step playback
Various playback modes are available including
still pictures, fast forward/reverse, slow motion and
step frames.
¡On-screen display
Information about the current operation can be
displayed on a TV screen, allowing you to confirm
the currently active functions (such as program
playback), on the TV screen using the remote
control.
¡Random playback for Audio CD
This unit can shuffle the order of tracks to play
them in random order.
¡Program playback for Audio CD
You can program the order of tracks to play them in
any desired order.
¡Search
Chapter search / Title search / Track search / Time
search
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Repeat
Chapter / Title / Track / All / A-B
¡Zoom
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the unit for 5 minutes in the stop mode.
After the screen saver program is activated for 15
minutes, the power automatically turns off.
Magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Virtual Surround
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Choices for audio language and sound mode
You can select the desired audio language and
sound mode, if different languages and modes are
available on a disc.
- 7 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - [Fig.1]
OPEN/
POWER
VOLUME
CHANNEL
STOP
SKIP
PLAY
SKIP
PAUSE CLOSE
VIDEO
L–AUDIO–R
–SEARCH–
HEADPHONE
1
2
3
4
5
6
7 8 9 10 9 1112 13
7.Remote sensor window
8.STOP C Button [P.20]
Stops operation of the disc.
[Fig. 2]
- REMOTE CONTROL -
9.SKIP H / G Buttons [P.22]
Press once to skip chapters or tracks to a desired
point.
OPEN/
POWER PICTURE SELECT
CLOSE
4
12
35
E
D
SEARCH
/
Buttons (Front panel) [P.21]
14
1
4
2
5
8
0
3
6
Press and hold to change forward or reverse
playback speed.
CH.
6
15
16
10. PLAY B Button [P.20]
7
SLEEP
9
+100
Starts playback of the disc.
VOL.
5
11. PAUSE F Button [P.21]
Pauses the current disc operation.
12. OPEN/CLOSE A Button [P.20]
Hit to insert a disc into or remove it from the
tray.
+10
SKIP
ZOOM
MUTE
34
33
32
9
10
PLAY
STOP
REV
FWD
13. HEADPHONE Jack
8
DISC
MENU
To connect headphone (not supplied) for personal
listening.
PAUSE SLOW
DISPLAY
11
17
31
14. PICTURE Button [P.13]
ENTER
30
29
28
Hit to adjust the picture.
SETUP
TITLE
RETURN
18
19
20
15. Number Buttons
CLEAR SEARCH MODE REPEAT
A-B
TV Mode: [P.13]
Press two digits to directly access the desired
channel.
Remember to hit [0] before a single digit channel.
+100 Button–
Hit to select cable channels which are higher
than 99.
DVD Mode: [P.22]
Hit to enter the desired number.
+10 Button–
Hit to enter the desired numbers which are higher
than 9.
27
AUDIO SUBTITLE ANGLE
MODE
21
22
23
26
25
24
1.Disc loading tray
2.VIDEO input Jack
Connect to the video output jack of a video camera or
VCR.
3.AUDIO L/R input Jacks
Connect to the audio output jacks of a video camera or
VCR.
16. SLEEP Button [P.14]
Sets the Sleep Timer.
4.POWER Button [P.13]
17. DISPLAY Button
Hit to turn the power on and off.
Buttons [P.13]
Press to control the volume level for the DVD and TV.
Buttons [P.13]
Press to select memorized channels.
TV Mode:
K
L
5.VOLUME (VOL.)
/
Displays the current channel number on the TV
screen.
DVD Mode: [P.25]
K
L
6.CHANNEL (CH.)
/
Displays the current status on the TV screen.
- 8 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
- REAR PANEL - [Fig.3]
ANT.
COAXIAL
36 37
38
18. SETUP Button [P.26]
K
L
{
B
30.
/
/
/
Buttons
Hit to enter or exit the setup menu of TV or DVD.
TV Mode: [P.13]
Press to select a setting mode from the menu on
19. TITLE Button [P.20]
the TV screen.
Displays the title menu.
Press to select or adjust from a particular menu.
DVD Mode: [P.20]
Press to select a menu item.
20. CLEAR Button [P.22]
Hit to clear or cancel a setting currently entered.
21. MODE Button [P.23, 24, 25]
31. DISC MENU Button [P.20]
Hit to call up the program screen or the random
screen in the stop mode.
Calls up the DVD menu.
E
32. REV
Button [P.21]
Hit to call up the Black Level Setting screen or
the Virtual Surround screen during playback.
Hit to view the DVD picture in fast reverse or
slow reverse motion.
22. SEARCH MODE Button [P.22]
D
FWD
Button [P.21]
Hit to locate a desired point.
Hit to view in fast or slow forward motion.
23. AUDIO Button [P.24]
33. ZOOM Button [P.21]
Hit to select a desired audio language or sound
mode.
Enlarges part of a DVD-reproduced image.
34. MUTE Button [P.13]
24. SUBTITLE Button [P.24]
Mutes the sound. Hit it again to restore sound.
Hit to select a desired subtitle language.
35. SELECT Button [P.11]
25. REPEAT Button [P.23]
Hit to change to TV mode, external input mode or
DVD mode.
Repeats playback of the current disc, title, chap-
ter, or track.
36. COAXIAL Jack [P.11]
26. ANGLE Button [P.24]
Connect to the digital input of an external
amplifier or decoder (for DVD Audio only).
Hit to change the camera angle to see the
sequence being played back from a different angle
(if available).
37. ANT(ENNA). Jack [P.10]
Connect to an antenna, cable system or satellite
system.
27. A-B Button [P.23]
Repeats playback of a selected section.
38. Power cord [P.13]
28. RETURN Button [P.22]
Connect to a standard AC outlet (120V/60Hz).
Returns to the previous screen in the setup menu.
NOTE:
29. ENTER Button [P.15]
Remove the power cord from the hook to avoid
breaking a wire before you connect to a standard
AC outlet.
•
Hit to accept a setting.
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
•
If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- 9 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTIONS
Plug the incoming cable into the ANT. jack on the rear of the unit.
If your cable service supplies you with a converter box or if you use a
satellite system, connect the box with this unit as shown below.
Cable
TV signal
Antenna
or
Incoming cable from home Antenna /
Cable Company (No Cable Box)
ANT.
COAXIAL
Rear of the unit
ANT.
Cable Box or
Satellite Box*
OR
OUT
IN
[Fig. 4]
Incoming cable from Cable Company
or Satellite Antenna
*NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals and
require a special converter to receive these channels.
Consult your local cable company.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Bent pin
NOTE:
Before plugging the antenna into the ANT. jack of the unit, check that the pin is
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the
ANT. jack of the unit.
Cable
Plug
(Needs to be
straightened)
(Straight pin)
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack
before moving the unit.
- 10 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO FRONT A/V INPUT JACKS
When you watch a program recorded on another source (VCR or video camera), use the
AUDIO/VIDEO input jacks on the front of the unit.
AUX
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO
jacks of this unit.
K
L
Then press [SELECT] or [CH.
/
] until “AUX” appears on the screen.
OPEN/
POWER
VOLUME
CHANNEL
STOP
SKIP
PLAY
SKIP
PAUSE
CLOSE
VIDEO
L–AUDIO–R
E
–SEARCH–
D
HEADPHONE
ex.
VCR or video camera, etc.
To the Audio output jacks
Audio Cable
(commercially available)
(IN)
(OUT)
(OUT)
VIDEO
L–AUDIO–R
[Front of the unit]
To the Video output jack
Video Cable
(commercially available)
(IN)
[Fig. 5]
NOTE:
When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the
monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R
channel equally.
•
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH
DIGITAL INPUT JACKS (for DVD)
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
ANT.
COAXIAL
ex.
MD deck, DAT deck, etc.
To COAXIAL jack
(Only DVD AUDIO OUT)
(OUT)
To Coaxial digital
Audio input jack
Audio coaxial digital cable
(commercially available)
[Fig. 6]
(IN)
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner’s Manuals for the components to be connected to the unit.
Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-
tings may generate noise distortion and may also damage the speakers. (Refer to page 27.)
•
•
•
- 11 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a
DOLBY DIGITAL Data stream from its COAXIAL jack. By hooking the unit up to a Dolby Digital decoder,
you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as
enjoyed in movie theaters.
Use audio coaxial digital cables (commercially available) for the audio connections.
Center
speaker
ANT.
COAXIAL
Front speaker
(left)
Front speaker
(right)
To COAXIAL jack
(Only DVD AUDIO OUT)
(OUT)
Dolby Digital
decoder
To Coaxial digital
Audio input jack
Audio Coaxial digital cable
(commercially available)
Subwoofer
Surround
speaker
(left)
Surround
speaker
(right)
(IN)
[Fig. 7]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner’s Manuals for the components to be connected to the unit.
If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the
setup mode. (Refer to page 27.)
•
•
•
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the
setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the
speakers. (Refer to page 27.)
•
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
[BATTERY PRECAUTIONS]
Be sure to follow the correct polarity as indicated
in the battery compartment. Reversed batteries
may cause damage to the device.
•
Do not mix different types of batteries together
(e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
•
3)Replace the cover.
If the device is not to be used for a long period of
time, remove the batteries to prevent damage or
injury from possible battery leakage.
•
Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture.
•
- 12 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TV SECTION
TV OPERATION AND SETTINGS
WATCHING A TV PROGRAM
DEGAUSSING
TV
This television has a degaussing circuit that will clear
up color errors on the TV screen that are caused by
any excess magnetism which happens to get too close
to the TV. This circuit is designed to operate once
when the set is first plugged in. If minor color
errors are seen in some locations on the screen,
please unplug the TV for approximately 30 min-
utes. When the TV is plugged back in, the degauss-
ing circuit will operate once to clear them up. Repeat
this procedure any time the TV screen is accidentally
magnetized or when the TV is moved or relocated.
TV
1 Plug in the unit power cord
Plug the unit power cord into a standard
AC outlet.
NOTE:
If any digits appear in the corner of the
•
screen, hit [POWER] without unplug-
ging the power cord.
2 Turn on the unit
Hit [POWER] to turn on the unit.
PICTURE CONTROL
TV
3 Select the channel number
K
L
Press [CH.
/
] or the Number buttons to select
The unit’s picture controls – BRIGHT, CON-
TRAST, COLOR, TINT and SHARPNESS – are
preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a more natural looking image.
your desired channel number.
Notes for using the Number buttons:
¡You must precede single-digit channel numbers
with a zero (for example: 02, 03, 04 and so on).
¡When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
Make sure ...
The unit must be turned on.
•
1 Call up the menu
4 Adjust sound
Hit [PICTURE].
X
Y
Press [VOL.
/
] to adjust the
volume.
2 Select item you want to adjust
VOLUME 20
K
L
Hit [MUTE] to instantly mute the
sound.
Hit it again to restore the previous sound level.
Press [
/
] until desired control is displayed.
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
BRIGHT
CONTRAST
COLOR
NOTE:
K
L
BRIGHT
TINT
SHARPNESS
If you press [CH.
/
] in the DVD mode, you
•
–
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +
can change the TV channels. Even if you turn off
the unit in the DVD mode, when you turn it on
again, it will go into the TV mode.
3 Adjust the setting
Press
[s
/
B
]
to adjust to your desired level within 5
TO WATCH CABLE OR SATELLITE
CHANNEL
seconds.
s
to decrease
brightness
to decrease
contrast
B
If the unit is connected to a cable box or satellite
•
BRIGHT
to increase
brightness
to increase
contrast
K
L
box, press [CH.
/
] to select CH3 or CH4
according to the output channel setting of the
device and select desired channel on that device.
CONTRAST
COLOR
TINT
SHARPNESS to soft
to pale
to brilliant
TO WATCH EXTERNAL INPUT
to purple
to green
to clear
When an external equipment is connected to the
•
front AUDIO/VIDEO input jacks, press
K
L
[SELECT] or [CH.
/
] repeatedly until “AUX”
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
•
appears on the screen.
- 13 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
If the unit displays a black box on
the TV screen, this means that the
unit is set to the TEXT mode. To
clear screen, select [CAPTION1],
[CAPTION2] or [OFF].
•
SLEEP TIMER
TV
The Sleep Timer function turns off the unit without
using [POWER] after a desired period of time.
Make sure ...
The unit must be turned on.
•
1 Call up the Sleep Timer Setting
Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.
1 Select “CAPTION”
Hit [SETUP].
- TV SETUP -
2 Set sleep time
Hit [SLEEP] repeatedly until your
desired sleep time appears.
CHANNEL SET UP
V-CHIP SET UP
K
L
Press [
/
] to point to
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
“CAPTION”.
Each additional press will increase
the time by 30 minutes up to 120
SLEEP 120 MINUTE
minutes.
2 Select your desired caption mode
Hit [ENTER] repeatedly until your
desired caption menu appears.
After 5 seconds, the Sleep Timer setting will disap-
pear automatically.
- TV SETUP -
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
B
TO CANCEL THE SLEEP TIMER
Hit [SLEEP] to call up the Sleep Timer Setting. Hit
[SLEEP] repeatedly until “SLEEP 0 MINUTE”
appears.
3 Exit the caption setting mode
Hit [SETUP] to exit the menu.
NOTE:
CLOSED CAPTION SYSTEM
Even if there is a power failure of any kind, the
unit will retain its memory for this feature.
•
TV
You can view specially labeled (cc) TV programs,
movies, news and pre-recorded tapes with either a
dialogue caption or text display.
CAPTION mode: You can watch dramas, movies and
news while captioning the dialogues and the contents
of news.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps 1 to 2 and select [OFF] using
[ENTER]. Then hit [SETUP] to return to TV mode.
TEXT mode: You can watch half screen text informa-
tion if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is
usually used for a second language if available.
NOTES:
Not all programs are broadcast with closed cap-
•
tions. Your unit is designed to provide error free
closed captions from high quality antenna, cable
and VCR signals. Conversely, poor quality signals
are likely to result in caption errors or no captions
at all. Common signal conditions which may cause
caption errors are listed below:
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
•
•
•
•
ghosts or airplane flutter
- 14 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDING/DELETING CHANNELS
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
CHANNEL SET UP
Make sure ...
TV
The unit must be turned on.
•
AUTO CHANNEL PROGRAMMING
1 Select “CHANNEL SET UP”
- TV SETUP -
Hit [SETUP].
As the initial setting, this unit has memorized all
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
K
L
]
Press
[
/
to point to “CHAN-
channels, including the ones not available in your
area. This feature automatically puts only available
channels into the memory.
NEL SET UP”, then hit [ENTER].
- TV SETUP -
1 Select “CHANNEL SET UP”
2 Select “ADD/DELETE CH”
– CHANNEL SET UP –
Hit [SETUP].
K
L
B
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
Press [
/
] to point to
B
ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
K
L
]
Press
[
/
to point to
“ADD/DELETE CH”, then hit
[ENTER].
“CHANNEL SET UP”, then hit
[ENTER].
2 Begin channel scanning
3 Enter the desired channel number
– CHANNEL SET UP –
K
L
]
Press
[
/
to point to “AUTO
K
L
Press [CH.
/
] or the Number
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
CH PROGRAMMING”, then hit
[ENTER].
The tuner scans and memorizes all
the active channels in your area.
buttons until your desired channel
08
number appears. (You can also
K
L
press [
/
] to enter it.)
ADD / DELETE
You must precede single-digit
channel numbers with a zero
(Example: 02 ... 09).
•
(Example: CH8)
3 After scanning
The tuner stops on the lowest memorized channel.
NOTES:
When “AUTO CH PROGRAM-
MING” is activated where there
is no TV signal input, “NO TV
SIGNALS” will appear on the
display after the completion of
channel scanning.
When selecting cable channels which are higher
than 99, hit [+100] first, then press the last two
digits. (Example: to select channel 125, first hit
[+100] then hit [2] and [5].)
•
•
NO TV SIGNALS
4 Delete (or add) it from (or into) memory
Hit [ENTER]. The channel number changes to light
red. The channel is deleted from memory.
The unit may recognize CATV channels to be TV
To delete another channel, repeat steps 3 to 4.
If you hit [ENTER] again, the channel is memo-
rized again.
•
•
•
channels if reception condition is poor. In this case,
check the antenna connection and try “AUTO CH
PROGRAMMING” again when reception condi-
tions are better.
Added channel : Light blue
Deleted channel : Light red
Channel memory programming is NOT neces-
•
sary when connected to a cable box or satellite
box. Just select the channel for cable box or
satellite input (ex. CH3) on the unit, then select
your desired channel on the cable box or satel-
lite box.
5 Exit the channel setup mode
Hit [SETUP] to exit the menu.
NOTE:
To confirm that channel(s) has been deleted or
•
K
L
added, press [CH.
/
].
- 15 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
V-CHIP SET UP
When you select a rating and set
•
it to [BLOCK], the higher ratings
will be blocked automatically.
The lower ratings will be avail-
able for viewing.
TV–Y
TV–Y7
TV–G
TV–PG (DLSV )
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
TV
(
)
B
This feature enables parents to prevent their children
from watching inappropriate material on TV. When
you try to access a program which is blocked,
“PROTECTED PROGRAM by ...” message appears
on the TV screen.
When you set the lowest rating to
[VIEW], all other ratings will automatically be
available for viewing.
•
V-CHIP SET UP
5 Setting “Sub-Ratings”
Make sure ...
TV–Y
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
When you select the ratings of
B
TV–Y7
TV–G
(
)
The unit must be turned on.
•
TV-Y7, TV-PG, TV-14 or TV-MA
you will have the option of setting
sub rating categories.
TV–PG (
)
)
)
TV–14
(
TV–MA(
1 Select “V-CHIP SET UP”
Hit [SETUP].
- TV SETUP -
K
L
Press [
/
] to select a rating with
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
sub-ratings you wish to block, then
B
TV–Y7
FV
[BLOCK]
[BLOCK]
K
L
Press [
/
] to select “V-CHIP
B
hit [ENTER] twice.
SET UP”, then hit [ENTER].
K
L
Press [
/
] to select a sub-rating,
then hit [ENTER] to set it to
[BLOCK] or [VIEW].
2 Enter Access code
Press the Number buttons to
enter the access code.
TV–PG
[BLOCK]
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
ACCESS CODE
_
_
_
_
For the first time set-up or in the
event the unit has lost power,
enter the default code of 0000.
•
Selection
TV-Y7
FV
Rating Category Explanations
Fantasy Violence
3 Select the desired item
TV-PG, TV-14, TV-MA
K
L
Press [
/
] to select “TV RATING”, “MPAA RAT-
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)
Coarse Language
Sexual Situation
Violence
ING” or “CHANGE CODE”, then hit [ENTER].
Refer to the pages below to set up each item.
– V-CHIP SET UP –
A
P 16 Step
P 17 Step
4
4
4
V
B TV RATING
MPAA RATING
CHANGE CODE
B
NOTE:
The blocked sub-ratings will
appear next to the rating category
in the “TV RATING” menu.
C
P 17 Step
•
TV–Y
TV–Y7
TV–G
TV–PG (DLSV)
TV–14 (DLSV)
TV–MA ( LSV)
[VIEW]
(
)
[VIEW]
[VIEW]
B
[BLOCK]
[BLOCK]
[BLOCK]
A
TV RATING SET UP
Follow steps to in the “V-CHIP SET UP” section
1
3
above.
6 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
4 Blocking TV programs
K
L
B
TV–Y
TV–Y7
TV–G
TV–PG (
TV–14
TV–MA(
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Press [
/
] to select a rating that
NOTE:
(
)
you wish to block.
Hit [ENTER] repeatedly to set it to
[BLOCK] or [VIEW].
)
)
)
To change the rating, the TV must
•
(
PROTECTED PROGRAM
by TV-Y
be turned to an unprotected pro-
gram. If “PROTECTED PRO-
GRAM by ...” appears on the
screen, please change the channel
to a station that is not protected.
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7
TV-G
Appropriate for children seven and older
General Audience
TV-PG
TV-14
Parental Guidance suggested
Unsuitable for children under 14
TV-MA Mature audience only
- 16 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
B
MENU LANGUAGE
MPAA RATING SET UP
TV
Follow steps to in the “V-CHIP SET UP” sec-
tion on page 16.
1
3
- TV SETUP -
1 Select “LANGUAGE”
Hit [SETUP].
4 Select your desired item
G
[VIEW]
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
K
L
Press [
/
] to point to your
PG
[VIEW]
PG–13
R
NC–17
X
[VIEW]
B
K
L
Press [
/
] to point to
B
[BLOCK]
[BLOCK]
[BLOCK]
desired item, then hit [ENTER] to
select [BLOCK] or [VIEW].
“LANGUAGE”.
Selection
G
PG
PG-13
R
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompa-
nying parent or adult guardian
No one under 17 admitted
2 Select “ENGLISH”, “ESPAÑOL” or “FRANÇAIS”
Hit [ENTER] repeatedly to select “ENGLISH”,
“ESPAÑOL”= Spanish or “FRANÇAIS”= French.
3 Exit the Language mode
Hit [SETUP] to exit the menu.
NC-17
X
Mature audience only
NOTES:
This function effects only the language on the
screen menu and not the audio source.
•
When you select a rating and set it to [BLOCK],
the higher ratings will be blocked automatically.
The lower ratings will be available for viewing.
When you set the lowest rating to [VIEW], all
other ratings will automatically be available for
viewing.
•
•
If for some reason the menu is in Spanish or
•
K
L
French, hit [SETUP], press [
/
] to point to
“IDIOMA [ESPAÑOL]” or “LANGAGE
[FRANÇAIS]”, then hit [ENTER] repeatedly to
select desired language, then hit [SETUP].
5 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
C
CHANGE ACCESS CODE
Follow steps to in the “V-CHIP SET UP” sec-
1
3
tion on page 16.
4 Enter New code
NEW CODE
Press the Number buttons to enter
your desired access code in the
“NEW CODE” space, then enter
the same code in the “CONFIRM
CODE” space. When completed,
the menu will return to “V-CHIP SET UP”.
X X X X
CONFIRM CODE
_
_
_
_
Make sure you enter exactly the same new code in
the “CONFIRM CODE” space as one in the
“NEW CODE” space. If they are different, the
“NEW CODE” space is cleared for redoing.
•
5 Exit the V-Chip setting mode
Hit [SETUP] to exit the menu.
NOTE:
Your personal access code will be erased and will
•
return to the default (0000) when a power failure
occurs or when you turn off the power using a
wall switch. If you have forgotten the code, unplug
the power cord for 10 seconds to restore the access
code to 0000.
- 17 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
TV Display
5A
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
A
B
14
15
CATV channel
TV Display
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CATV channel
R
S
T
U
V
W
W+1
37
W+2
38
W+3
39
W+4
40
W+5
41
W+6
42
W+7
43
W+8
44
W+9
45
TV Display
31
32
33
34
35
36
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
CATV channel
TV Display
CATV channel
TV Display
76
77
78
79
80
81
82
83
84
85
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
86
87
88
89
90
W+55 W+56 W+57 W+58
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
CATV channel
TV Display
91
92
93
94
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display
106
W+80 W+81 W+82 W+83 W+84
121 122 123 124 125
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CATV channel
TV Display
- 18 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
Recorded
Playable
discs
Disc size
Region code
Disc types
Mark (logo)
signals
DVD-Video
or
* 1,2,4,6,10,11
Example
12 cm
or
8 cm
Title 1
Title 2
DVD-RW
DVD-R
Digital video
(MPEG2)
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1
Chapter 2
-
-
-
* 1,3,4,5,6
7,9,10
DVD+RW
DVD+R
* 1,3,4,5,6,8,9,10
Audio CD
* 4,6,10
Audio CD
Example
12 cm
or
8 cm
Digital audio
Track 1
Track 2
Track 5
Track 6
Track 3
Track 4
CD-RW
CD-R
* 4,5,6,9,10
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not
play them back. Even if they are played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with
the DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be
played back at all or normally (the picture or sound may not be smooth, etc.).
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not
play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-
mat can only be played back on unit with the same region code.
UNPLAYABLE DISCS
¡
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3
On the following disc, the sound MAY NOT be heard.
¡
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
Any other discs without compatibility indications
¡
- 19 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING A DISC
BASIC PLAYBACK
GENERAL FEATURES
DVD-V
CD
DVD-V
DVD may contain menus to navigate the disc and
Getting started
access special features. Press the appropriate
Number buttons or [K /L/s / B] to highlight your
selection in the DVD main menu and hit [ENTER] to
confirm.
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1
Hit [POWER].
¡The power will turn on.
NOTES:
¡Select DVD mode by hitting [SELECT], then
2
3
Hit [OPEN/CLOSE A] to open disc loading
tray.
operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
Place the chosen disc in the tray, with the
label facing up.
DISC MENU
DVD-V
1
Hit [DISC MENU].
¡The DVD main menu will appear.
¡If the feature is not available,
appear on the TV screen.
¡If disc menu is available on the disc, audio language,
subtitle options, chapters for the title and other
options will appear for selection.
symbol may
4
Hit [PLAY O].
¡The tray will close automatically and playback will
then start from the first chapter or track of the disc.
¡Closing the disc tray manually or by hitting
[OPEN/CLOSE A] also starts playback.
¡If the playback does not start automatically, hit
[PLAY O].
2
Press [K /L/s / B] to select an item and
hit [ENTER] to confirm selection.
¡When you playback a DVD which features a title
menu, it may appear on the screen. In this case,
refer to “TITLE MENU” on this page.
TITLE MENU
5
Hit [STOP C] to stop playback.
DVD-V
NOTES:
1
Hit [TITLE].
¡When the DVD mode has been switched to the TV
mode, the DVD mode shuts down first and then the
TV picture and sound appears in about 4 seconds.
Similarly, when [POWER] is hit to turn off in the
DVD mode, this mode shuts down first and then the
unit is turned off.
¡The title menu will appear.
¡If the feature is not available,
appear on the TV screen.
symbol may
2
Press [K /L/s / B] to select an item, and
hit [ENTER] to confirm selection.
¡A “prohibited icon” may appear
at the top-right on the TV screen
during operation, warning that a
prohibited operation has been
encountered by the DVD or the
disc.
¡With DVDs that use titles for playback program
signals, playback may start from the second title or
it may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡Hit [DISC MENU] to call up the DVD menu.
¡Hit [TITLE] to call up the title menu.
NOTE:
¡Contents of menu and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
- 20 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SLOW FORWARD /
SLOW REVERSE
RESUME
DVD-V
CD
DVD-V
1
During playback, hit [STOP C].
¡Resume message will appear on the TV screen.
1
2
During playback, hit [PAUSE F].
D
E
] .
Press [FWD
] or [REV
2
Hit [PLAY O], playback will resume from the
point at which playback was stopped.
¡“
1” or “
1” appears on the screen.
3
To select another speed, repeat step 2 until
your required speed number appears on the
screen.
¡To cancel resume, hit [STOP C] twice.
¡The resume information stays on even when the
power is turned off.
¡Slow forward or reverse speed varies with the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
¡When you press buttons on the front panel, press
PAUSE
E
D
DVD-V
CD
and hold [SEARCH
/
] for a few seconds.
4
To return to normal playback, hit [PLAY O].
1
During playback, hit [PAUSE F].
¡Playback will pause and sound will be muted.
2
To continue playback, hit [PLAY O].
ZOOM
DVD-V
STEP BY STEP PLAYBACK
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
DVD-V
1
Hit [ZOOM] during playback.
¡Playback will continue.
1
During playback, hit [PAUSE F].
¡Playback will pause and sound will be muted.
2
Hit [ZOOM] repeatedly to select the required
zoom factor: ZOOM1, ZOOM2, ZOOM3 or
OFF.
2
3
The disc goes forward by one frame each
time [PAUSE F] is hit.
To exit step by step playback, hit [PLAY O].
3
4
Press [K /L/s / B] to move the zoomed
picture across the screen.
FAST FORWARD /
FAST REVERSE
To exit zoom mode, hit [ZOOM] to OFF.
NOTES:
¡Zooming function does not work while disc menu is
shown.
DVD-V
CD
¡Zooming function is not available on some discs.
¡It may take several seconds to slide the zoomed pic-
ture.
D
] or
1
During playback, press [FWD
E
].
E
[REV
D
¡“
1” or “
1” appears on the screen.
¡The picture may be distorted if you operate other
E
F
2
To select another speed, repeat step 1 until
your required speed number appears on the
screen.
functions repeatedly (ex. [PAUSE ] or [REV
],
etc.) in the zoom mode.
¡For DVDs, fast forward/reverse search speed is dif-
ferent depending on the disc. Approximate speed is
1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).
¡For Audio CDs approximate speed is 1(×2), 2(×8)
and 3(×30).
¡When you press buttons on the front panel, press and
E
D
hold [SEARCH
/
] for a few seconds.
3
To return to normal playback, hit [PLAY O].
- 21 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
DVD-V
CD
There are three ways to begin playback on an Audio
CD at a specific track.
1
2
During playback, hit [SEARCH MODE] three
times (CD: twice) to display the Time Search
on the TV screen.
Using the Number buttons
Within 30 seconds, enter a desired disc
time using the Number buttons.
1
Press the Number buttons to enter the
desired track number.
¡Playback will start at the specified time.
¡Hit [CLEAR] to erase the incorrect input.
¡When there is no need to enter a number, “0”
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, hit [3]).
appears automatically. For example, “ 0 : 0
:
”
- - -
¡To play track 26, hit [+10], [2], [6].
appears in the Time Search display if the total time
of the track or title is less than 10 minutes.
Using [SEARCH MODE]
1
Hit [SEARCH MODE].
¡The track search display appears.
MARKER SETUP SCREEN
DVD-V
CD
2
Within 30 seconds, select the desired track
number using the Number buttons.
Use markers to memorize your favorite places on a
disc.
¡For single digits hit [0] first, if the total track of the
disc is 10 tracks or more.
1
Hit [SEARCH MODE] four times (CD: three
times) during playback.
¡Playback will start at the selected track.
¡The display screen and Markers will appear on the
TV screen.
Using [SKIP H /
G
]
During playback, hit [SKIP G] to move the next
track. Hit it repeatedly to skip subsequent tracks. Hit
[SKIP H ] to go back to beginning of the current
track. Hit it repeatedly to go to the previous tracks.
¡If [SKIP H / G] is pressed while the playback
is paused, the playback will be paused again after
skipping to the next track.
2
3
Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,
or 10 and ensure that “
appears in the display.
:
:
”
- - - - - - - -
When you reach the desired point, hit
[ENTER].
NOTE:
¡The Title or Track and elapsed playing time will
appear in the TV screen.
¡[SKIP H / G] are not operative when playback
is stopped.
4
To return to the Marker later, hit [SEARCH
MODE] four times (CD: three times) during
playback and press [s / B] to choose the
desired marker, then hit [ENTER].
TITLE / CHAPTER SEARCH
DVD-V
NOTES:
1
Hit [SEARCH MODE] once for the Chapter
search, twice for the Title search during
¡Operations which erase all Markers:
– Opening the disc tray.
playback.
_/2
– Turning off the power.
– Hitting [SELECT].
– Selecting “AC” at step 2 and hitting [ENTER].
¡To clear a marker:
2
Enter the desired chapter/title number using
the Number buttons.
– Press [s / B] to select a cursor on to the marker
number and hit [CLEAR].
¡You can mark up to 10 points.
¡Playback will start at the selected chapter or title.
¡Hit [CLEAR] to erase the incorrect input.
¡For single digits hit [0] first, if the total number of
chapter or title of the disc is 10 or more.
5
Press [SEARCH MODE] or [RETURN] to
exit.
- 22 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
CD
You may determine the order in which tracks will play.
REPEAT is available only during playback.
REPEAT TITLE / CHAPTER
DVD-V
1
In the stop mode, hit [MODE].
¡The “PROGRAM” screen will appear.
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
2
Press [K /L] to select a track, then hit
[ENTER].
¡Hit [CLEAR] to erase the
most recently entered track.
¡If the entire Program cannot be
displayed at once on a screen,
“G” appears to go to the next
page and “H” appears to go
back to the previous page.
PROGRAM
CD-DA
TOTAL 1:03:30
CHAPTER
TITLE
OFF
(repeat off)
1
5
3:30
5:10
1
3:30
2
3
4
5
6
7
4:30
5:00
3:10
5:10
1:30
2:30
10 4:20
11 3:00
12 3:20
17 4:10
22 2:50
2/3
(current chapter repeat) (current title repeat)
ENTER
1/4
PLAY
1
3:30
CLEAR
NOTES:
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
3
Repeat step 2 until you have selected all the
tracks you want to play in the program.
4
Hit [PLAY O] to play the programmed tracks.
REPEAT TRACK
NOTES:
CD
¡While the program is being played back, hitting
[STOP C] works as follows.
To activate the repeat function, hit [REPEAT]
during playback.
¡The repeat mode changes as described below every
time you hit the button.
¡Hit [STOP C] once and then [PLAY O] again,
playback will restart from the point where
[STOP C] was hit. (Program continued)
¡Hit [STOP C] twice and then [PLAY O] again,
playback will restart from the track in the usual
way. (Program canceled)
TRACK
(current track repeat)
ALL
OFF
(repeat off)
(entire disc repeat)
¡Up to 99 tracks can be entered.
¡To erase all tracks in the program at once, select
“ALL CLEAR” at the bottom of the list at step 2.
¡If you like to repeat the current track in the program,
NOTES:
¡Repeat setting will be cleared when moving to other
hit [REPEAT] several times until “
TRACK”
track.
appears during playback. If you like to repeat the
¡Repeat playback does not function during A-B
repeat playback.
entire program hit [REPEAT] several times until
“
ALL” appears during playback.
A-B REPEAT
RANDOM PLAYBACK
DVD-V CD
CD
1
¡“
Hit [A-B] at your chosen starting point.
A-” appears briefly on the TV screen.
This function shuffles the playing order of tracks
instead of playback in the sequence.
2
Hit [A-B] again at your chosen end point.
A-B” appears briefly on the TV screen, and the
1
In the stop mode, hit [MODE] twice.
¡“
¡“RANDOM” screen appears.
RANDOM
repeat sequence begins.
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
no indication
3
To exit the sequence, hit [A-B].
NOTES:
-
-
-
-
PLAY
¡The A-B repeat section can only be set within the
current title (for DVDs) or current track (for Audio
CDs).
¡A-B repeat is not available with some scenes in
DVD.
¡To cancel the A point which was set, hit [CLEAR].
¡A-B repeat playback does not function during title,
chapter, track or all repeat playback.
2
Hit [PLAY O] to start random playback.
NOTE:
¡If you like to repeat the current track in the random
selection, hit [REPEAT] several times until
“
TRACK” appears during playback. If you like
to repeat the entire random selection hit
[REPEAT] several times until “ ALL” appears
during playback
.
- 23 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
STEREO SOUND MODE
CD
DVD-V
The unit allows you to select a language for subtitles
during DVD disc (if available) playback.
1
Hit [AUDIO] repeatedly during playback to
select between “STEREO”, “L-ch” or “R-ch”.
STEREO
1
Hit [SUBTITLE] during playback.
¡The subtitle language will
appear on the display bar at
the top of the TV screen.
1.ENG/6
¡
STEREO - both right and left channels are active (stereo)
L-ch - only left channel is active
R-ch - only right channel is active
2
3
Hit [SUBTITLE] repeatedly to select your
desired subtitle language.
CAMERA ANGLE
DVD-V
To turn off subtitles, hit [SUBTITLE] repeat-
edly until “OFF” appears.
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
NOTES:
the camera angle when the “
screen.
” icon appears on the
¡Hitting [SUBTITLE] may not work on some DVDs
with multiple subtitle languages. In this case, set it
on the disc menu. (Operation varies between discs.
Refer to the manual of the disc.)
1
Hit [ANGLE] during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
¡If the desired language is not shown after hitting
[SUBTITLE] several times, the disc does not have
subtitles in that language.
1 / 8
¡When “NOT AVAILABLE”
appears on the TV screen, it
means no subtitle is recorded
on the scene.
NOT AVAILABLE
¡If the “ANGLE ICON” setting is “OFF” in the
“OTHERS” menu, the “
(Refer to page 28.)
” icon will not appear.
¡If you choose a language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, “---” will be displayed instead.
(Refer to page 26.)
2
Hit [ANGLE] repeatedly to select your
desired angle.
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
AUDIO LANGUAGE
1
Hit [MODE] during playback.
DVD-V
OFF
The unit allows you to select a language during DVD
disc (if multi languages are available) playback.
1
Hit [AUDIO] during playback.
2
Hit [ENTER] to switch “ON/OFF”.
1.ENG Dolby D 3/2.1ch 48k/3
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
(Initial setting)
2
Hit [AUDIO] repeatedly to select your
desired language.
3
Press [MODE] twice or [RETURN] to exit.
NOTE:
NOTE:
¡The setting will be saved even if the unit is turned
off.
¡Hitting [AUDIO] may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
- 24 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
VIRTUAL SURROUND
DVD-V
CD
You can enjoy surround-sound effect over two speak-
ers on this unit.
1
Hit [MODE] twice (CD: once) during play-
back.
OFF
2
3
Hit [ENTER] to set it “1” (Natural effect), “2”
(Emphasized effect) or “OFF”.
Hit [MODE] to exit.
¡You can also exit the menu by hitting [RETURN].
NOTE: (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
THE ON-SCREEN INFORMATION
DVD-V
CD
You can check the information about the current disc by hitting [DISPLAY].
For DVD-Vs
For Audio CDs
1
Hit [DISPLAY] during playback to show cur-
rent Chapter.
1
Hit [DISPLAY] during playback to show the
current Track.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
¡The elapsed and remaining playing time of the cur-
9/49
0:00:00 -0:03:30
rent track will be displayed.
4/12 0:03:21 - 0:02:15
T
2
Hit [DISPLAY] again to show current Title.
2
Hit [DISPLAY] again to show current Total
Track.
¡The elapsed and remaining
playing time of the current title
will be displayed.
1/3 0:00:00 - 1:23:45
¡The elapsed and remaining playing time of the total
track will be displayed.
4/12 0:13:45 - 0:45:40
T
3
Hit [DISPLAY] again.
¡The bit rate and the current
repeat setting will be
displayed.
T
L1
3
Hit [DISPLAY] again to exit.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
NOTE:
¡When you are playing a disc in PROGRAM or
RANDOM mode, “ PROGRAM” (or RAN-
DOM) will be displayed at step 2.
4
Hit [DISPLAY] again to exit.
PROGRAM
B
- 25 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE DVD SET UP ITEMS
Language
Code Language
Code
CUSTOM MENU
A-B
L-N
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
4748 Laothian
4747 Latin
4752 Latvian;Lettish
6563 Lingala
4759 Lithuanian
4764 Macedonian
5471 Malagasy
4765 Malay
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
DVD-V
You can change the DVD player’s settings.
1
Hit [SETUP] twice in the stop mode so that
the DVD SETUP menu appears.
4771 Malayalam
4772 Maltese
4847 Maori
SETUP
¡Hit [L] to select “CUSTOM”
then hit [ENTER].
QUICK
CUSTOM
INITIALIZE
5167 Marathi
Bengali;Bangla
Bhutani
Bihari
4860 Moldavian
5072 Mongolian
4854 Nauru
NOTE:
¡If the menu does not appear, hit [PLAY O] first,
then hit [STOP C]. Make sure the disc is in the stop
mode, then slowly hit [SETUP] twice.
Bislama
Breton
4855 Nepali
4864 Norwegian [NOR]
4853
5971 Occitan
4851 Oriya
Oromo(Afan)
5759 Panjabi
4947 Pashto;Pushto
7254 Persian
4961 Polish
5464 Portuguese [POR]
4965 Quechua
5047 Rhaeto-Romance
6058 Romanian [RUM]
5160 Russian [RUS]
5161
5166 Samoan
Sangho
5261 Sanskrit
5256 Scots Gaelic
5255 Serbian
Bulgarian
Burmese
Byelorussian
O-R
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
2
Select the desired item.
C-E
K
L
¡Press [
/
] to select the desired item then hit
Cambodian
Catalan
[ENTER] to confirm.
Chinese [CHI]
Corsican
Croatian
Refer to the pages below to set up each item.
SETUP
CUSTOM
A
P 26 Step
3
3
3
3
3
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
B
P 27 Step
C
P 27 Step
S
D
P 28 Step
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
E
F-H
P 28 Step
Faroese
Fiji
A
LANGUAGE SETTING
Follow steps to in the “CUSTOM MENU” section
Finnish [FIN]
French [FRE]
Frisian
5264 Serbo-Croatian
5271 Sesotho
5358 Setswana
5747 Shona
1
2
above.
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
K
L
3
Press [
hit [ENTER].
/
] to select the desired item then
5051 Sindhi
5158 Singhalese
5758 Siswat
5360 Slovak
SETUP
LANGUAGE
AUDIO:
Sets the audio language.
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
Gujarati
Hausa
Hebrew
5367 Slovenian
5447 Somali
5569 Spanish [SPA]
5455 Sundanese
5467 Swahili
OFF
SUBTITLE:
ENGLISH
Sets the subtitle language.
DISC MENU:
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Swedish [SWE]
Sets the language for DVD menu.
5565
5560 Tagalog
5547 Tajik
5551 Tamil
5557 Tatar
5347 Telugu
5566 Thai
T
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
K
L
] to select a setting then hit
4
Press [
[ENTER].
/
SETUP
LANGUAGE
LANGUAGE
LANGUAGE
¡If “OTHER” is selected on
the “AUDIO”, “SUBTITLE”
or “DISC MENU” screen,
press four-digit number to
enter the code for the
desired language. (Refer to
the language code list.)
¡Only the languages support-
ed by the disc can be select-
ed.
AUDIO
ORIGINAL
ENGLISH
FRENCH
5647 Tibetan
5669 Tigrinya
5760 Tonga
5765 Tsonga
5757 Turkish [TUR]
6469 Turkmen
5771 Twi
SETUP
SUBTITLE
OFF
ENGLISH
FRENCH
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
6460
U-Z
5761 Ukrainian
5767 Urdu
Uzbek
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
SETUP
DISC MENU
ENGLISH
FRENCH
Vietnamese
Volapuk
Welsh
SPANISH
Wolof
Xhosa
Yiddish
5
Hit [SETUP] to exit the menu.
NOTES:
Yoruba
Zulu
¡Language Setting for Audio and Subtitle are not
valid for some discs due to default setting of the
disc. In this case, set them by hitting [AUDIO] and
[SUBTITLE]. (Refer to page 24.)
¡If you select a language that is not supported by the
disc, subtitle will automatically be set OFF and the
first item of the audio languages will be automatical-
ly set.
If you choose a language that has a 3 letter language
code, the code will be displayed every time you change
the AUDIO or SUBTITLE language setting above. If
you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
- 26 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
B
C
DISPLAY SETTING
AUDIO SETTING
Choose the appropriate Audio settings for your equip-
ment as it only affects during the playback of DVD
discs.
Follow steps to in the “CUSTOM MENU” section
on page 26.
1
2
K
L
3
Press [
/
] to select the below items then
Follow steps to in the “CUSTOM MENU” section
on page 26.
1
2
hit [ENTER].
TV MODE:
QUICK
K
L
3
Press [
/
] to select the below items then
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
hit [ENTER].
DRC (Dynamic Range
Control):
¡To compress the range of soft
to loud sound.
¡4:3 LETTER BOX (default):
To show black bars on top
and bottom of the screen.
SETUP
DISPLAY
SETUP
DRC
DOWN SAMPLING
DOLBY DIGITAL
AUDIO
ON
ON
BITSTREAM
TV MODE
STILL MODE
4:3 LETTER BOX
AUTO
¡4:3 PAN & SCAN: To show
a full height picture with both sides trimmed.
¡The default setting is “ON”.
DOWN SAMPLING:
¡ON : Output in 48 kHz.
(default)
¡OFF : Output the original
sound.
When playing disc with copyright Protection
¡If you select “OFF”, copyright protection will be
activated and sound will be down sampled at 48kHz.
SETUP
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
STILL MODE
This function allows you to adjust picture resolution
and quality in the still mode.
:
SETUP
DISPLAY
¡AUTO (default):
Automatically select the best
resolution setting (FRAME
or FIELD) based on the data
characteristics of the pictures.
¡FIELD: Select “FIELD” when the pictures are still
unstable even if “AUTO” is selected.
FIELD stabilizes the pictures, although the picture
quality may become coarse due to the limited
amount of data.
¡FRAME: Select “FRAME” to display relatively
motionless pictures in higher resolution.
FRAME improves the picture quality, although it
may unstabilizethe pictures due to simultaneous
output of two field data.
TV MODE
STILL MODE
4:3 LETTER BOX
AUTO
SETUP
DRC
DOWN SAMPLING
DOLBY DIGITAL
AUDIO
DOLBY DIGITAL:
QUICK
ON
ON
BITSTREAM
Set to “BITSTREAM” when
the unit is connected to a
Dolby Digital Decoder.
¡BITSTREAM: Output a Dolby Digital signal
(default)
¡PCM: Convert the Dolby Digital to PCM
(2 channel stereo)
4
Hit [SETUP] to exit the menu.
4
Hit [SETUP] to exit the menu.
QUICK MENU
¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the
QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 26.
1
LANGUAGE SETTING FOR THE ON-SCREEN MENUS
¡You can access the TV SETUP menu by hitting [SETUP] from the DVD mode. Refer to
“MENU LANGUAGE” on page 17 to change the language for the on-screen menus.
- 27 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
D
PARENTAL CONTROL
IF YOU FORGET THE PASSWORD
Parental Control limits the disc viewing that exceed
your setting (with a password or playback will stop).
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
1
Hit the Number buttons [4], [7], [3], [7] at
step 3. Then enter your new password.
¡Password will be cleared and parental level will be
set to “ALL”.
PARENTAL LEVEL
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s rat-
ings exceed the level you set.
2
Proceed with steps 4 to 6 again.
E
OTHER SETTINGS
Follow steps 1 to 2 in the “CUSTOM MENU” section
on page 26.
Follow steps to in the “CUSTOM MENU” section
1
2
on page 26.
3
Enter your four-digit password then hit
[ENTER].
K
L
3
Press [
/
] to select the below items, then
SETUP
PARENTAL
PASSWORD
Enter current password.
hit [ENTER].
SETUP
OTHERS
ANGLE ICON
ON
AUTO POWER OFF ON
ANGLE ICON:
¡Hit [ENTER] repeatedly to turn Angle icon “ON” or
“OFF”.
K
L
] to select “PARENTAL LEVEL”
4
5
Press [
/
SETUP
PARENTAL
then hit [ENTER].
PARENTAL LEVEL
PASSWORD CHANGE
ALL
¡The default setting is “ON”.
AUTO POWER OFF:
¡Hit [ENTER] repeatedly to turn Auto Power off
K
L
] to select the desired level then
Press [
/
“ON” or “OFF”.
hit [ENTER].
SETUP
PARENTAL
PARENTAL LEVEL
¡
The default setting is “ON” and the screen saver pro-
gram starts when there is no input from the unit for 5
minutes in the stop mode. After the screen saver pro-
gram is activated for 15 minutes, the power is auto-
matically turned off.
ALL
8
7 [NC-17]
6 [R]
6
Hit [SETUP] to exit the menu.
NOTES:
4
Hit [SETUP] to exit the menu.
¡
When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the pass-
word. (in the event you forget the password, see below)
K
L
¡To change the password, press [
/
] to select
INITIALIZE
“PASSWORD CHANGE” at step 4 then hit
[ENTER]. Enter the four-digit password, then hit
[ENTER].
DVD-V
This allows you to return all selections of SETUP
(except for “PARENTAL” and menu language) to
their default settings.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
1
Hit [SETUP] twice in the stop mode so that
the “INITIALIZE” menu appears.
¡Record the password in case you forget it.
K
L
CONTROL LEVELS
2
Press [
/
] to select “INITIALIZE” then hit
¡
ALL
SETUP
[ENTER].
QUICK
CUSTOM
INITIALIZE
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
K
L
3
Press [
/
] to select “YES” then hit
[ENTER] twice.
¡
Levels 7 to 2
All the settings (except for
“PARENTAL” and menu
language) will be cleared.
¡To cancel the initialization,
select “NO”.
Only DVD software intended for general use and
children can be played back.
SETUP
INITIALIZE
Initialize?
NO
YES
¡
Level 1
Only DVD software intended for children can be
played back, with those intended for adult and gen-
eral use prohibited.
4
Hit [SETUP] to exit the menu.
- 28 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-
sulting the following checklist.
PROBLEM
CORRECTIVE ACTION
Make sure the power plug is connected to an AC outlet.
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote control.
You have to be within 23 feet of the unit.
No power
•
•
•
•
•
No operation by infrared remote
control
•
•
Check if the correct mode is selected. If not switch the mode by
hitting [SELECT], whichever you need.
TV Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
No picture or sound
CORRECTIVE ACTION
Make sure the AC cord is connected to an AC outlet.
Check antenna connection.
Hit [SELECT] to select TV mode.
Then try other TV feature.
•
•
•
Let the unit program its tuner memory.
Adjust direction or replace antenna.
Adjust picture controls.
Check for broken pin of the antenna cable.
Adjust volume control on remote control or main unit.
Hit [MUTE] to restore sound.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
No picture or poor picture on the
unit
No sound or poor sound
Bars On Screen
If outside antenna is being used, check for broken wire.
Check for local interference.
Picture Distorted or Blurred
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Try a new channel, if OK, then possible station trouble.
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust “COLOR” control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Adjust “CONTRAST” & “BRIGHT” control.
Try a new channel, if OK, then possible station trouble.
Is antenna connected to jack on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Adjust “CONTRAST” & “BRIGHT” control.
- 29 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
Picture OK, Sound Poor
CORRECTIVE ACTION
Try a new channel, if OK, then possible station trouble.
Check for local interference.
Make sure the AC cord is connected to an AC outlet.
Check batteries in remote control.
Magnetism from nearby appliances and geomagnetism might affect
the color of the TV picture. Move the unit away from the appliances,
the unit can repair itself automatically. If you want to repair immedi-
ately, unplug the power cord, then plug it in again 30 minutes later or
so. This automatically resets the unit.
•
•
•
•
No operation by infrared remote
control
Different color marks on screen
•
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
Misspelling in captions
Error committed by the closed captioning production company.
Possible in a live broadcast. Not in case of a prerecorded program.
A few seconds of delay is common for live broadcast.
Display capacity may not exceed 220 words per minute. If a dialogue
exceeds that rate, selective editing is used to insure that the captions
remain up-to-date with the current TV screen dialogue.
•
•
•
•
•
•
•
Text is not shown in its entirety or
a delay occurs from what is being
said
Captions scrambled with white
boxes
Caused by interferences of building, power lines, thunderstorms, etc.
No captions in a program which
must contain closed caption
The broadcast may use a time compression process to speed up the
program. The decoder cannot read the compressed information and
captions will be lost.
You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or
Caption “OFF”.
•
•
•
•
•
Black box in the TV screen
- 30 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Mode
PROBLEM
CORRECTIVE ACTION
Insert a correct video disc that plays on this unit.
Hit [SELECT] to select DVD mode, then try other DVD feature.
Insert the disc.
No picture
•
•
•
•
•
•
•
•
•
•
•
•
Disc cannot be played
Clean the disc.
Place the disc correctly, with the label side up.
Cancel the parental lock or change the control level.
Connect the audio cables firmly.
No sound
Turn the power of the audio component on.
Correct the audio output settings.
Correct the input settings on the audio component.
This unit does not support DTS audio. This is not a malfunction.
No DTS audio is output
Distorted picture
There are some cases where pictures may be slightly distorted,
which are not a sign of a malfunction.
Although pictures may stop for a moment, this is not a malfunction.
The selected language is not available for audio or subtitles on the
DVD. (This is not a malfunction.)
•
•
•
Audio or subtitle language
does not match the set up
The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-
•
era angles. (This is not a malfunction.)
Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected
•
changed
language. (This is not a malfunction.)
•
•
•
•
“Prohibited icon” appears on the
screen, prohibiting an operation
CD sound dropout
That operation is prohibited by the unit or the disc.
(This is not a malfunction.)
Scratched disc. Replace the disc with an unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
•
- 31 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CABINET CLEANING
SERVICING
Should your unit become inoperative, do not try to
•
Wipe the front panel and other exterior surfaces of
the unit with a soft cloth immersed in lukewarm
water and wrung dry.
•
correct the problem by yourself. There are no user-
serviceable parts inside. Turn off, unplug the power
cord and please call our help line mentioned on
the front page, to locate an Authorized Service
Center.
Never use a solvent or alcohol. Do not spray insec-
•
ticide liquid near the unit. Such chemicals may
cause damage and discoloration to the exposed sur-
faces.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to
“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.
•
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup
unit.
DISC HANDLING
Handle the discs so that fingerprints and dust do
not adhere to the surfaces of the discs.
To clean-off, use a soft cloth.
•
•
•
•
•
•
•
Do not use a hard cloth since this will mar the disc.
Wipe the disc in a straight line from center to edge.
Never wipe with a circular motion.
Do not use detergent or abrasive cleaning agents.
Always store the disc in its protective case when it
is not used.
- 32 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Sound output:
2 speakers, 1W, 8 ohm
TV
CRT:
20 inch in-line gun,
90˚ deflection tube
NTSC-M
OTHER SPECIFICATIONS
Terminals
Antenna input:
Television system:
Closed caption system: §15.119/FCC
Channel coverage:
VHF:
UHF:
CATV:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
Video input:
Audio L/R input:
Headphone:
2 ~ 13
14 ~ 69
1/8" stereo (3.5 mm)
2 ~13, A ~ W,
W+1 ~ W+84,
A-5 ~ A-1, 5A
181 channel
frequency synthesized
tuning system
Direct access keyboard,
programmable
scan and up/down
Coaxial digital
audio output:
One pin jack,
500m Vpp (75 ohm)
Digital encoded
Tuning System:
Channel access:
Remote control:
infrared light system
Operating
temperature:
5°C to 40°C
(41°F~104°F)
Power requirements: AC 120V, 60Hz
Power consumption
(Maximum):
Picture tube:
Dimensions:
80W
20" PF
H : 20-1/4" (514mm)
W : 20-3/16" (512mm)
D : 19-13/16" (503mm)
46.3 lbs. (21.0kg)
DVD
Product type:
Discs:
Output signal format: NTSC color
DVD Player
DVD video, Audio CD
Weight:
Designs and specifications are subject to change without notice.
If there is a discrepancy between languages, the default language will be English.
•
•
- 33 -
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICE
■ INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SECCIÓN DE TV
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35
CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 36
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 37
IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 38
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
EQUIPADO CON TOMAS DE ENTRADA DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 36
CONTROLES DE OPERACIÓN Y FUNCIONES
• Consulte la figura 1 de la página 8 para el panel frontal de la unidad
• Consulte la figura 2 de la página 8 para el mando a distancia
• Consulte la figura 3 de la página 9 para la vista posterior
1. Bandeja de carga del disco
2. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
Botón +100
Presione para seleccionar canales de televisión por
cable cuyo número sea superior a 99.
Modo DVD:
Presione para introducir el número deseado.
Botón +10
Presione para introducir números superiors a 9.
3. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
16. Botón SLEEP
4. Botón POWER
Presione para encender y apagar la unidad.
Utilise para ajustar el temporizador de dormir.
17. Botón DISPLAY
K
L
5. Botones VOLUME (VOL.)
/
Modo TV:
Presione para controlar el nivel de volumen del DVD y
el televisor.
Indica el número del canal en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor.
K
L
6. Botones CHANNEL (CH.)
/
Utilice para seleccionar canales memorizados.
7. Ventanilla del sensor de mando a distancia
8. Botón STOP
Detiene la operación del disco.
9. Botones SKIP H /
Presione una vez para omitir capítulos o pistas y
desplazarse a un punto específico.
18. Botón SETUP
Presione para entrar o salir del menú de configuración
de televisor o DVD.
C
19. Botón TITLE
G
Para visualizar el menú de títulos.
20. Botón CLEAR
Para cancelar o borrar un ajuste entrado actualmente.
E
D
Botones SEARCH
/
(Panel frontal)
21. Botón MODE
Mantenga el botón presionado para cambiar la
velocidad de reproducción en avance o retroceso.
Presione para llamar la pantalla de la reproducción
programada o la de reproducción aleatoria en el modo
de parada.
10. Botón PLAY
Inicia la reproducción del contenido del disco.
11. Botón PAUSE
Hace una pausa en la reproducción del disco.
12. Botón OPEN/CLOSE
B
Presione para llamar la pantalla de ajuste del nivel del
negro o la pantalla de sonido ambiental durante la
reproducción.
F
A
22. Botón SEARCH MODE
Presione para insertar un disco en la bandeja o retirarlo
de ella.
Presione para localizar un punto deseado.
23. Botón AUDIO
13. Toma HEADPHONE
Presione para seleccionar un modo de sonido o idioma
de audio deseado.
Para conectar auriculares (no suministrados) y escuchar
en privado.
24. Botón SUBTITLE
14. Botón PICTURE
Presione para seleccionar el idioma de subtítulos
deseado.
Presione para ajustar la imagen.
15. Botones Numéricos
25. Botón REPEAT
Modo TV:
Repite la reproducción del disco, título, capítulo o pista
actual.
Presione dos cifras para acceder directamente al canal
deseado.
26. Botón ANGLE
No olvide presionar [0] antes de elegir un canal de una
Presione para cambiar el ángulo de la cámara y ver la
secuencia que se está reproduciendo desde un ángulo
diferente (si existe).
sola cifra.
- 34 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
33. Botón ZOOM
27. Botón A-B
Amplía parte de la imagen reproducida de un DVD.
Repite la reproducción de una sección seleccionada.
34. Botón MUTE
28. Botón RETURN
Suprime la salida de sonido. Presiónelo de nuevo para
restablecer el sonido.
Permite volver a la pantalla anterior en el menú de
configuración.
35. Botón SELECT
29. Botón ENTER
Presione para cambiar al modo TV, modo de entrada
externa o modo de DVD.
Presione para establecer un ajuste.
K
L
{
B
30. Botones
Modo TV:
/
/
/
36. Toma COAXIAL
Conecte solamente a la entrada digital de un
amplificador externo o decodificador (para audio de
DVD solamente).
Presione para seleccionar un modo de ajuste en el
menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o
establecer ajustes en un menú en particular.
Modo DVD:
37. Toma ANT.
Conecte a una antena, sistema de televisión por cable o
sistema de satélite.
Presione para hacer una selección en el menú.
31. Botón DISC MENU
38. Cable eléctrico
Muestra menú del DVD.
Conécte a un toma de CA estándar (120 V/60 Hz).
NOTA:
E
32. Botón REV
Antes de conectar el cable eléctrico a una toma de
Presione para mover la imagen de DVD en retroceso
rápido en o en cámara lenta en retroceso.
•
CA, retírelo del gancho para evitar dañarlo.
D
Botón FWD
Presione para mover en avance rápido o en cámara
lenta en el disco.
PREPARACIÓN PARA LA UTILIZACIÓN
NOTA:
CONEXIONES DE ANTENA/CABLE
Antes de enchufar la antena a la toma ANT. de la
unidad, compruebe que la clavija no esté doblada.
Si esta doblada, póngala derecha como se muestra
en la ilustración, y luego conéctela en la toma
ANT. de la unidad.
Consulte la figura 4 de la página 10
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que
proporciona recomendaciones para hacer una
conexión a tierra apropiada y, en particular,
especifica que la tierra del cable debe conectarse
al sistema de puesta a tierra del edificio, tan cerca
del punto de entrada del cable como sea posible.
Clavija doblada
Cable
Clavija
(Necesita enderezarse)
(Clavija derecha)
NOTA:
Para su seguridad y para evitar que se dañe
la unidad, desenchufe el cable de antena de la
toma ANT. antes de mover la unidad.
•
- 35 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
CONEXIÓN A TOMAS DE
ENTRADA DELANTERAS
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de
entrada AUDIO/VIDEO de la parte delantera de la
unidad.
Conecte las tomas de salida de audio/vídeo de otra
fuente a las tomas AUDIO L/R y VIDEO de esta
unidad.
CONEXIÓN A UN
DECODIFICADOR DOLBY
DIGITAL (para DVD)
Si utiliza esta unidad para reproducir un disco DVD
en un formato de sonido envolvente Dolby Digital de
5,1 canales, la unidad dará salida a un flujo de datos
DOLBY DIGITAL desde su toma COAXIAL. Si
conecta la unidad a un decodificador Dolby Digital,
podrá disfrutar de una tonalidad más convincente y
real, con un sonido envolvente potente y de alta
calidad similar al de los cines.
K
L
] hasta
Despúes, presione [SELECT] o [CH.
que aparezca “AUX” en la pantalla.
/
Utilice cables digitales coaxiales de audio
(disponibles en el comercio) para hacer las
conexiones de audio.
Consulte la figura 5 de la página 11
NOTA:
•
Cuando conecte una videograbadora monofónica
(otra fuente) a esta unidad, conecte la toma de
salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de esta unidad. El
audio saldrá igualmente por los canales izquierdo y
derecho.
Consulte la figura 7 de la página 12
NOTAS:
Asegúrese de apagar todos los componentes del
•
sistema antes de conectar otro componente.
Consulte los manuales de instrucciones de los
•
componentes que va a conectar a la unidad.
Si conecta un decodificador Dolby Digital, ajuste
•
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL (para DVD) •
la función “DOLBY DIGITAL” a “BITSTREAM”
para salida de audio en el modo de configuración.
A menos que se haga la conexión a un
decodificador Dolby Digital, ajuste la función
“DOLBY DIGITAL” a “PCM” para salida de
audio en el modo de configuración. La
Utilice un cable digital coaxial de audio (disponible en
el comercio) para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
Consulte la figura 6 de la página 11
NOTAS:
• La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la
doble D son marcas comerciales de Dolby
Laboratories.
• uAnsaegpúlaretisneadMe DapoagDarAtTo.dos los componentes del
• sCisotnesmulateanlotessmdaencuoanleesctdaer ointrsotrucoccmiopnoensendtee.los
PARA INSERTAR LAS PILAS
• Acojmuspteonlaenftuenscqióune “vDa Oa LcoBnYecDtaIrGaITlaAuLn”idaa“dP. CM”
para salida de audio en el modo de configuración.
La reproducción en una unidad utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede provocar daños a los altavoces.
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a
distancia en el sentido de la flecha.
2) Inserte 2 pilas “AA” en el
compartimiento de las pilas, en el
sentido indicado por las marcas de polaridad (+/-).
3) Vuelva a poner la cubierta.
- 36 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
SECCIÓN DE TV
PARA MIRAR UN
IDIOMA DEL MENÚ
PROGRAMA DE TV
TV
TV
1 Seleccione “LANGUAGE”
Presione [SETUP].
1 Enchufe el cable eléctrico
Enchufe el cable eléctrico de la unidad en un
tomacorriente de CA del hogar.
NOTA:
•
K
L
Presione [
/
] para apuntar a “LANGUAGE”.
2 Seleccione “ENGLISH”, “ESPAÑOL” o
Si aparecen números en la esquina de la pantalla,
“FRANÇAIS”
presione [POWER] sin desenchufar el cable
Presione [ENTER] repetidamente para seleccionar
“ENGLISH” = inglés, “ESPAÑOL” o
“FRANÇAIS” = francés.
eléctrico.
2 Encienda la unidad
Presione [POWER] para encender la unidad.
3 Salga del modo de idioma
Presione [SETUP] para salir del menú.
NOTAS:
3 Seleccione el número de canal
K
L
Presione [CH.
/
] o los botones numéricos para
seleccionar su número de canal deseado.
Esta función afecta sólo el idioma en el menú de la
pantalla y no la fuente de audio.
•
Nota para el uso de los botones numéricos:
¡Debe colocar un cero antes de los números de canal
de una sola cifra (por ejemplo: 02, 03, 04, etc.).
Si por alguna razón, el menú está en francés,
presione [SETUP], presione [
•
K
L
/
] para apuntar
¡
Cuando seleccione canales de cable de más de 99,
presione primero [+100] y después las dos últimas
cifras. (Ejemplo: para seleccionar el canal 125,
primero presione [+100] y después presione [2] y [5].)
al “LANGAGE [FRANÇAIS]” y presione
[ENTER] repetidamente para seleccionar el
idioma deseado y presione [SETUP].
4 Ajuste el sonido
X
Y
Presione [VOL.
/
] para ajustar el volumen.
Presione [MUTE] para silenciar instantáneamente el
sonido.
Presione nuevamente para recuperar el nivel de
sonido anterior.
NOTA:
K
L
Si presione [CH.
/
] en el modo DVD, puede
•
cambiar los canales de TV. Incluso si apaga la
unidad en el modo DVD, cuando vuelva a
encender, volverá al modo TV.
PARA VER CANALES DE CABLE O
SATELITE
Si la unidad está conectada a una caja de cable o
•
K
L
] para
caja de satélite, presione [CH.
/
seleccionar CH3 o CH4 de acuerdo con el ajuste
de canal de salida del dispositivo y seleccione el
canal deseado en el dispositivo.
PARA VER UNA ENTRADA EXTERNA
Cuando se conecta un equipo externo en las tomas
•
de entrada AUDIO/VIDEO frontales, presione
K
L
[SELECT] o [CH.
/
] repetidamente hasta que
aparezca “AUX” en la pantalla.
- 37 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA
MENÚ DE DISCO
DVD-V
CD
DVD-V
Para empezar
1
Presione [DISC MENU].
¡Conecte la alimentación del amplificador y otros ¡Aparecerá el menú principal de DVD.
componentes, si es necesario.
¡Si no existe la función, puede aparecer el símbolo
en la pantalla de TV.
1
Presione [POWER].
¡La alimentación se conectará.
¡Si el menú de disco existe en el disco, aparecerán el
idioma de audio, opciones de subtítulo, capítulos
para el título y otras opciones para su selección.
2
3
Presione [OPEN/CLOSE A] para abrir la
bandeja de carga del disco.
K
L
{
B
2
Presione [
/
/
/
] para hacer una
Ponga el disco deseado en la bandeja, con
la etiqueta hacia
arriba.
selección y presione [ENTER] para
confirmar la selección.
REANUDACIÓN
DVD-V
CD
1
Durante la reproducción, presione
[STOP C].
4
Presione [PLAY O].
¡Aparecerá el mensaje de continuación en la pantalla
¡La bandeja se cerrará automáticamente y la
reproducción comenzará desde el primer capítulo o
pista del disco.
de TV.
2
Presione [PLAY O], la reproducción continuará
desde el punto donde se paró la reproducción.
¡La reproducción también empieza cerrando
manualmente la bandeja del disco o presionando
[OPEN/CLOSE A].
¡Si la reproducción no comienza automáticamente,
presione [PLAY O].
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pantalla.
¡Para cancelar la continuación, presione dos veces
[STOP C].
¡La información de continuación permanece activada
incluso cuando apaga el interruptor principal.
5
Presione [STOP
C] para detener la reproducción.
- 38 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
- 39 -
ES
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNAI CORPORATION
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date
of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail
purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does
not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN
THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest Authorized Service Center or for general service inquiries, please call or
write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-242-7158
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
1EMN20326
T9102UC ★★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|