All-Weather Outdoor LCD Television
Owner’s Manual
Model 4660HD
Revision M46-006-4660HD-111005
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Cleaning instructions: Use a soft cloth with mild detergent in warm water to clean the SunBriteTV screen. Remove any dirt and salt
deposits from the unit, being careful to rinse the cloth frequently to avoid scratching the screen surface. Avoid using harsh chemicals,
ammonia, abrasives, or solvents when cleaning any surface on the screen. When the TV is not in use, it is important to keep it covered
with the SunBriteTV fitted Outdoor Dust Cover. Use a soft brush or towel to remove snow and ice from the TV. In areas where dust or salt
air is prevalent, it is recommended that the fiber filter be cleaned regularly (see instructions on Page 42).
attachments: Do not use attachments not specifically recommended by the manufacturer. Use of improper attachments can result in
accidents.
Power source: SunBriteTV must operate on a power source indicated on the specification label. If you are not sure of the type of power
supply used in your home, consult your dealer or local power company. When using the TV outdoors, you must use a GFI-protected AC
outlet with “in-use”waterproof cover.
installation: Do not place the product on an unstable cart, stand, tripod, table, or anywhere the unit is not permanently installed. Placing
the product on an unstable place can cause the product to fall, resulting in potential serious personal injuries, as well as damage to the
product.
Precautions when Transporting the TV: Carrying the television requires at least two people.
FCC statement
This equipment complies with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
Modifications not expressly approved by the
manufacturer could void the user’s authority to operate
the equipment under FCC rules. This device complies
with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
SunBriteTV Model 4660HD Operator’s Manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Ventilation: Adequate ventilation must be maintained to ensure reliable and continued operation and to protect
the television from overheating. Do not block ventilation slots and openings with objects, or install the television in
a place where ventilation may be hindered. sunBriteTV is not designed for built-in installation. Do not place the
product in an enclosed place such as bookcase or rack.
Power cord protection: The power cord must be routed properly to prevent people from stepping on it, or objects
from resting on it. Check the cords at the plugs and product.
Power source: This product must operate on a power source specified on the specification label. If you are unsure of
the type of power supply used in your home, consult your dealer or local power company.
Do not let metal pieces or objects of any kind fall into the television from ventilation holes. High voltage flows in the
product, and inserting an object can cause electric shock and/or short internal parts.
Do not mount sunBriteTV near a motor or transformer where strong magnetism is generated. Images on the
television will become distorted and the color irregular.
Do not mount sunBriteTV near heat sources such as radiators, heaters, stoves and other heat-generating products
(including amplifiers).
Do not submerge sunBriteTV in water: The SunBriteTV will resist water exposure from normal rain, sprinklers,
garden hoses, etc.; However, it is not designed to be submerged in water.
Do not pressure-wash sunBriteTV: SunBriteTV will resist water exposure from normal rain, sprinklers, garden hoses,
etc.; However, it is not designed to withstand pressure washers, high-pressure water jets, or hurricane-type weather.
Do not service sunBriteTV yourself: Removal of the television screen cover may expose you to high voltage or other
dangerous risks. Refer all servicing to a qualified service professional. Warranty will not be honored if you service the
unit yourself.
repair: If any of the following conditions occurs, unplug the power cord, and call a qualified service professional to
perform repairs:
When power cord or plug is damaged.
When objects have fallen into the product.
If unit was submerged in water or pressure-washed.
When product does not operate properly as described in the operating instructions. Do not touch the controls other
than as described in the operating instructions. Improper adjustments of controls not described in the
instructions can cause damage, which can require extensive repair work by a qualified technician.
When the product has been dropped or damaged.
When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the
product needs servicing.
replacement parts: In case the product needs replacement parts, make sure that the service person uses
replacement parts provided by SunBriteTV. Use of unauthorized parts can result in fire, electric shock and/or other
danger.
safety checks: Upon completion of service or repair work, ask the service technician to perform safety checks to
ensure that the product is in proper operating condition.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Instructions
Table of Contents
2
5
6
Supplied Accessories
TV Installation
Choose a Location for the TV
Rear Panel Internal Connect Source
Rear Panel Connections
Starting the TV
6
8
10
17
19
20
21
Side Panel and Front Panel Controls
Remote Control Guide
On-Screen Display Controls
Adjusting On-Screen Displays
Video Menu
22
24
25
26
28
31
31
32
33
35
36
39
40
40
Audio Menu
TV Menu
Set-up Menu
Parental Menu
Ratings Menu
Aspect Ratio
Closed Caption
Shortcuts to Browsing
Preset Modes
Trouble Shooting
Care of SunBriteTV
Specifications
PC Timing Codes
Features Information and Instructions
Programming Other Manufacturers’Universal Remote Control Devices
SunBriteTV Pixel Quality Policy
IR Emitter Installation
41
41
42
SunBriteTV Model 4660HD Operator’s Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Unpacking
After unpacking the SunBriteTV television, please make sure that the following items are included in the carton and
that they are in good condition. If items are damaged or missing, contact your dealer immediately.
SunBriteTV LCD Television Model 4660HD
Remote Control with Batteries
Operator’s Manual
Outdoor Dust Cover
Outdoor Dust Cover
Model 4660HD
Water-Resistant
Wireless Remote
Control
Operator’s
Manual
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation - Choose a Location for the TV
Choose a location for the TV
Important: The TV must be installed at least 5
feet from pool, spa, or other body of water.
The TV should be installed so the screen is not facing
direct sunlight, or can be easily turned away from
direct sunlight.
Ideal placement is in an area where the TV is shaded
by trees, landscape and/or structures, or under a patio
cover or gazebo.
If the sun shines directly on the screen for long periods
of time, dark areas may develop on the screen. This is a
normal reaction for the LCD panel, and will not cause
damage to the screen. Either turn the screen away from
the sun, or apply shade to the TV, and the dark areas
will quickly disappear.
important! To protect the life of the lCD screen,
keep the dust cover on the TV when the TV is
not in use.
SunBriteTV Model 4660HD Operator’s Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Internal Connect Source
rear Panel Connections
WARNING: Do not connect the power source before making connections.
Internal Connect Source
The Internal Connect Source allows you to easily connect to the Audio, Video, S-Video, SVGA, HDMI, Audio Out, RF, RS232, and 12
VDC connectors, and the IR emitter window. The Internal Connect Source is inside the Cable Cover located on the back of the unit
(Figure 1).
1. Unscrew the three gray Thumb Screws (Figure 1), and pull the cover towards you.
2. Route the cables to the proper inputs, and place the cable cords over the Rubber Sealing Gasket (Figure 2).
Note: There is an Indentation on the Rubber Sealing Gasket (on the bottom portion of the right and left sides). Make sure cable
cords are not placed on the Indentation.
3. Close the cover (Figure 3).
4. Press firmly on the cover, and secure the Thumb Screws tightly (Figure 4).
Cables are to be placed over
the Rubber Sealing Gasket
Figure 2
Figure 1
Cables are not to be placed
over the indentations
Thumb Screws
Figure 3
Figure 4
Press firmly on the cover, and secure the Thumb
Screws tightly.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
1
3
5
6
7
9
11
2
4
8
10
12
1. UsB: This port is used for factory firmware upgrades.
2. HDmi (4): HDMI connects to devices that use HDMI cable, such as Blue-ray or HD DVD player, or HD cable/satellite set-top box. This
connection port receives pure digital audio and high definition signal through one single cable. This port also can accept a HDCP video device
for video.
3. Vga: This connection port connects to a PC for video using VGA cable. Be sure to connect your audio cable to the VGA Stereo input if you
want sound out of VGA video source.
4. Vga stereo input: This connection port is for people who want to provide audio to the TV when using a PC or DVI video device. The sources
use 3.5 mini-jack audio cable.
5. Component 1 (yPbPr1) - This connection port is for DVD players or satellite/cable set-top boxes that use component cables. From left to
right, connect green, blue and red for video, and then connect white for left channel audio and red for right channel audio.
6. Component 2 (yPbPr2) - This connection port is for DVD players or satellite/cable set-top boxes that use component cables. From left to
right, connect green, blue and red for video, and then connect white for left channel audio and red for right channel audio.
7. audio Out-TOslink: This connection port is used for sending out digital audio signals to digital surround sound receivers. The black
connector cover needs to be pulled out and the port sends out either bit-stream or PCM digital sound signal to a home theater receiver with
digital input.
8. analog audio Out: This connection is used for connecting a headphone or amplifier to the TV
9. nTsC/aTsC (TV): This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The tuner is a hybrid
tuner that tunes to both analog and digital channels. This connection uses coaxial RF cable. For over the airwave digital stations please check
10. ir Window: The Internal Infrared (IR) Control Window allows the TV to be controlled from a remote system using IR commands. (To install
IR Emitter, see Page 42.)
11. speaker: This connection is to be used with SunBriteTV Model 4660HD speaker module only.
12. aV1 (CVBs or s-Video): Connects to devices that use composite or s-video cables such as VCR or camcorder or video game consoles.
Connect the video portion with either the yellow connector or the S-Video connector. Do NOT connect both video connectors. Use the
SOURCE button to select AV1 (CVBS) on your MAIN SOURCE if you are using the yellow plug for video, use the SOURCE button to select AV1
(S-Video) on your MAIN Source if you are using the S-Video connector to view this connection.
SunBriteTV Model 4660HD Operator’s Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Cable Descriptions:
Connection Descriptions:
Blue
Green
Red
Yellow
Green
White
Red
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
Switching Sources for Ports:
Model 4660HD offers several options when connecting
your devices to the TV. The chart below will help you
understand which source you switch to for each of the
ports.
COnneCTing TO an anTenna
Connecting to Digital Cable without Cable Box or Antenna:
Note: For ease of install, SunBriteTV has included a Push-on Coaxial Adapter.
1. Make sure the power to the TV is turned off.
2-a. Connect the Coaxial RF cable from your antenna
or digital cable to the Push-on Coaxial Adapter that was
shipped with the TV.
2-b. Slip on the Push-on Coaxial Adapter and Coax onto
the NTSC/ATSC port on the back of the TV.
3. Turn on the TV.
4. Select TV Air/Cable in the Menu/TV /Tuner mode.
5. Use the On-Screen Display to scan for channels (Setup/
TV/Channel Scan)
Please Note :
1. Not all broadcasts are in High Definition (HD). Please refer to
your local broadcasting stations for more information.
2. The TV’s tuner is designed for HDTV therefore requires a
stronger signal than normal TVs. If you cannot achieve that signal
level with your antenna or cable, your 4660HD might lose picture
or sound.
SunBriteTV Model 4660HD Operator’s Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
COnneCTing TO a DVD Player
Connecting with HDmi (Best)
Connecting with
Component (Better)
1. Make sure the power of TV and your DVD player is turned off.
2. With a Component Cable, connect the green connector to the
DVD player and Component 1’s green connector port on the TV.
1. Make sure the power of the TV and your DVD player is
turned off.
3. Connect the blue color connector to your DVD player and
Component 1’s blue connector port on the TV.
2. Connect a HDMI cable to the HDMI port of your DVD
player and the other end to the HDMI port off the back of
your TV.
4. Connect the red color connector to both your DVD player and
Component 1’s red connector port on the TV.
5. With an RCA Audio Cable, connect the white color connector to
both your DVD player and Component 1’s white connector port on
the TV.
3. Turn on the TV and your DVD player.
4. Use the remote control’s source button or the source
button on the TV to switch to HDMI.
6. Connect the red color connector to both your DVD player and
Component 1’s red connector port on the TV.
Please Note :
Refer to the DVD player’s manual to make sure the DVD player
is configured to output correctly to the TV.
7. Turn on the TV and your DVD player.
8. Use the remote control’s source button or the source button on
the TV to switch to YPbPr.
Please Note :
Please Note :
1. Refer to the DVD player’s manual to make sure the DVD
player is configured to output correctly to the TV.
1. If Component 1 is already occupied, please use Component 2 as
your connection port and switch to source YPbPr2.
2. This TV does not decode Bit stream digital audio, so make
sure the DVD is setup for PCM digital audio through HDMI.
2. Refer to the DVD player’s manual to make sure the DVD player
is configured to output correctly to the TV.
3. If HDMI 1 is occupied, use HDMI 2 as your connection port.
4. This TV will turn off automatically if there’s no signal present for
more than 15 minutes.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
COnneCTing TO a DVD Player (Continued)
Connecting with
Composite (Fair)
Connecting with s-Video (fair)
1. Make sure the power of the TV and your DVD player is turned
off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Obtain a Yellow Video Cable. Connect the Yellow Video
connector to both your DVD player and Composite’s Yellow Video
connector port off the back of your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector
to both your DVD player and Composite’s S-Video connector
port off the back of your MODEL 4660HD.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your TV.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your MODEL 4660HD.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
5. Turn on the TV and your DVD player.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source button
on the right side of the TV to switch to AV1 (CVBS).
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (S-Video).
Please note:
1. If AV 1 is already occupied, use AV2, as your connection port, and switch source to AV 2 (S-Video)
2. Reference the DVD player’s manual to make sure the DVD player is configured to output correctly to the TV.
3. This TV will turn off automatically if there’s no signal present for more than 15 minutes.
SunBriteTV Model 4660HD Operator’s Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
COnneCTing TO a saTelliTe Or CaBle seT-TOP BOX
Connecting with HDmi (Best)
Connecting with
Component (Better)
1. Make sure the power of the TV and your set-top box is
turned off.
1. Make sure the power of TV and your set-top box is turned off.
2. Obtain a Component Cable. Connect the green color
connector to both your set-top box and Component 1’s green
connector port off the back of your TV.
2. Connect a HDMI cable to the HDMI output of your set-top
box and the other end to the HDMI port off the back of your
TV.
3. Connect the blue color connector to both your set-top box
and Component 1’s blue connector port off the back of your TV.
3. Turn on the TV and your set-top box.
4. Use the remote control’s source button or the source
button on the right side of the TV to switch to HDMI 1.
4. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV.
Please Note :
5. Obtain a RCA Audio Cable. Connect the white color connector
to both your set-top box and Component 1’s white connector port
off the back of your TV to the right side of your green, blue, red
component connection.
1
Refer to the set-top box’s manual, to make sure the set-
top box is configured to output correctly to the TV.
2. If HDMI 1 is already occupied, use HDMI 1 as your
connection port and switch source to HDMI 2.
6. Connect the red color connector to both your set-top box and
Component 1’s red connector port off the back of your TV to the
right side of your green, blue, red component connection.
3
SunBriteTV’s MODEL 4660HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
7. Turn on the TV and your set-top box.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
8. Use the remote control’s source button or the source button
on the TV to switch to YPbPr1.
Please Note :
1. If Component 1 is already occupied, please use Component 2
as your connection port and switch to source YPbPr2.
2. Please refer to the set-top box’s manual to make sure the set-
top box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 4660HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
Page 14
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
COnneCTing TO a saTelliTe Or CaBle seT-TOP BOX (Continued)
Connecting with
Composite (Fair)
Connecting with s-Video (Fair)
1. Make sure the power of the TV and your DVD player is
turned off.
1. Make sure the power of the TV and your DVD player is
turned off.
2. Obtain a Yellow Video Cable. Connect the Yellow Video
connector to both your DVD player and Composite’s Yellow
Video connector port off the back of your TV.
2. Obtain an S-Video Cable. Connect the S-Video connector
to both your DVD player and Composite’s S-Video connector
port off the back of your MODEL 4660HD.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your TV.
3. Obtain a RCA Audio Cable. Connect the white color
connector to both your DVD player and Composite’s white
connector port off the back of your MODEL 4660HD.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
4. Connect the red color connector to both your DVD player
and Composite’s red connector port off the back of your TV.
5. Turn on the TV and your DVD player.
5. Turn on the TV and your DVD player.
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (CVBS).
6. Use the remote control’s source button or the source
button on the right side of the TV to switch to AV1 (S-Video).
Please Note :
Please Note :
1. If AV 1 is already occupied, use AV 2 as your connection
port and switch source to AV 2 (S-Video).
1. If AV 1 is already occupied, use AV 2 as your connection
port and switch source to AV 2 (S-Video).
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
2. Refer to the set-top box’s manual to make sure the set-top
box is configured to output correctly to the TV.
3. SunBriteTV’s MODEL 4660HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
3. SunBriteTV’s MODEL 4660HD supports SONY’s universal
remote code. Please look up SONY’s codes in your universal
remote’s hand book.
4. This TV will turn off automatically if there’s no signal present
for more than 15 minutes.
4. This TV will turn off automatically if there’s no signal
present for more than 15 minutes.
SunBriteTV Model 4660HD Operator’s Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Rear Panel Connections
COnneCTing TO an eXTernal amPliFier Or amPliFieD sPeaKers
Connecting with TOslink Digital (Best)
Connecting with rCa audio analog (good)
1. Make sure the power of the TV and your receiver is turned
off.
1. Make sure the power of the TV and your receiver is turned off.
2. Obtain a Coaxial SPDIF cable, connect it to your receiver’s
coaxial SPDIF digital input and the Coaxial SPDIF connection
on the LINE OUT port off the back of the TV.
2. Obtain a 3.5mm stereo/audio cable (if your amplifier
audio connection requires RCA audio out jacks you will need
to obtain an 1/8”Stereo Mini Plug to RCA adapter cable).
Connect it to your receiver’s audio input connection and the
3.5mm stereo/audio connection on the Analog Audio port on
the back of the TV.
3. Turn on the TV and your receiver.
Please Note :
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound->Digital
Audio Out function. Make sure the option is on Bit Stream.
3. Turn on the TV and your receiver.
Please Note :
2. If your receiver is making static noises when receiving Bit
Stream, you must use the PCM option instead.
1. If you want pure digital stream for your receiver to
decode, you must also configure the TV’s OSD Sound->Digital
Audio Out function. Make sure the option is on Bit Stream.
3. Refer to the receiver’s manual to make sure the receiver is
configured to receive signals correctly from the TV
2. If your receiver is making static noises when receiving Bit
Stream, you must use the PCM option instead.
3. Refer to the receiver’s manual to make sure the receiver
is configured to receive signals correctly from the TV
COnneCTing TO a PC
1. Make sure the power of the TV and your PC is turned off.
Connecting with rCa audio analog
2. Obtain a 15-pin D-Sub VGA cable, connect to the VGA output of
your PC and the other end to the VGA port off the back of your TV.
3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC
and the other end to the VGA Stereo Input port.
4. Turn on the power of the TV and your PC.
5. Use the remote control’s source button or the source button the
TV to switch to VGA.
Please Note :
1. For the best results, please set your PC resolution to
1920 x 1080 at 60 Hz. Refer to the PC or graphic card’s manual for
further instructions on how to set your resolution and refresh rate.
2. Refer to your PC manual for video output requirements of the
video card.
3. The VGA port of the TV features a power saving mode which will
automatically turn off the TV if there is no signal provided for more
than 15 minutes.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Starting the TV
starting the TV
if you’ve connected antenna or Cable to the TV
SunBriteTV Model 4660HD Operator’s Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation – Starting the TV
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Installation--Starting the TV
Connecting the Power Cord
WARNING:
TV AND GFCI RECEPTACLE MUST BE INSTALLED AT LEAST 5 FEET AWAY FROM STANDING WATER , SUCH AS (BUT NOT LIMITED
TO) A POOL OR SPA.
Connect the power cord after you have made connections to your video equipment.
Connect the Power Cord to a GFCI-protected AC outlet
with “in-use”waterproof cover.
Warning: TV must be installed at least 5 feet away from
standing water, such as (but not limited to) a pool or
spa.
Power Cord
Back Panel
Power
Menu
Turns TV on/off.
Displays the On-Screen Display (OSD) menu.
In OSD menu, press key to return to pre-phase.
Vol+ /Vol-
Adjusts volume.
In OSD menu, both keys are used to navigate within menu.
Vol+ is used to select the highlighted options.
CH+/CH-
Source
Adjusts channels.
In OSD menu, both keys are used to navigate within the menu.
Press to change the input sources.
IR Sensor
SunBriteTV Model 4660HD Operator’s Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Guide
ON – Powers the TV On.
OFF – Powers the TV Off.
0~9 – Sets the channels.
Dash (-) – Inserts the dash for selecting digital channels directly.
R – Returns to the previous channel.
FREEZE – Freezes the TV picture. CC – Cycles between different closed
captioning modes.
SLEEP – Sets the Sleep timer.
CC– Selects Closed Caption.
V+ – Functions the Volume Up and Menu Right.
V- – Functions the Volume Down and Menu Left.
MUTE – Mutes the TVs Audio.
MENU – Opens / Exits the TV menu.
CH+ – Functions the Channel Up and Menu Up.
CH- – Functions the Channel Down and Menu Down.
MTS – Selects stereo, mono, or second audio programming.
SRS – Sets Surround Sound.
DNR – Enables the Digital Noise Reduction on the TV.
ADD/Del – Adds or deletes the current channel.
CH Lock – Locks the current channel you are on, so that kids cannot view
the locked channel unless unlocked by a password. You will also need to
input a password when locking the channel.
h / i / f / g / – Allow you to navigate inside the OSD menu. They also
function as CH+/- for digital channels in the tuner.
(Enter) – Allows you to select functions inside the OSD menu, acts as
the Enter button for OSD menu for changing channels.
SOUND – Selects various preset sound settings.
EXIT – Allows you to quit from the OSD menu..
PICTURE – Selects various preset picture settings.
GUIDE – Opens the current digital channel information guide.
SOURCE – Cycles between different inputs of the TV.
INFO – Shows current channel information, display input and resolution.
SHIFT – Used with the 0-9 numeric pad to select inputs.
ASPECT – Changes the TV between different display modes.
FAVORITE
channel list.
– Changes the channel up or down from you Favorite
FAVORITE ADD / DEL – Adds or deletes the current channel from the
favorites channel list.
Picture in Picture/Picture On Picture (PiP and POP) Functions
AUDIO – Switches Audio from the TV and PIP or POP windows.
VIDEO – Switches video from the PIP window to the main screen.
SOURCE – Changes the input source of the PIP window and POP window.
ON/OFF – Turns on or off the PIP and POP window.
SIZE – Changes size of the PIP window.
POS – Changes the position of the PIP window.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Guide
This remote control follows Sony’s TV remote
codes with discrete on/off and input select.
Direct TV code is 10,000
About the Water-Resistant
Remote Control
®
The SunBriteTV Water-Resistant Remote Controller is engineered to give you many years of service.
“Water-resistant”means that the remote control can be in water for short periods of time without damaging the
internal workings of the unit. It can be left in the rain, and even dropped in water, as long as it is retrieved quickly.
The remote control should not be left floating in water.
The functionality of the remote control is under warranty for one year. If the remote control malfunctions within the
one-year warranty period, replace the batteries with new long-life alkaline batteries.
If the problem is not solved with new batteries, contact the SunBriteTV Customer Support Team. SunBriteTV will
repair or replace the remote control at SunBriteTV’s option.
If you have a warranty claim, contact the SunBriteTV Customer Support Team for further instructions.
866.357.8688
On-Screen Display Controls
SunBriteTV Model 4660HD Operator’s Manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Video menu
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Video Menu
SunBriteTV Model 4660HD Operator’s Manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Audio Menu
aUDiO menu
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – TV Menu
TV menu
SunBriteTV Model 4660HD Operator’s Manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Set Up
set Up menu
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Set Up Menu
set Up menu
SunBriteTV Model 4660HD Operator’s Manual
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Set Up Menu / Parental Menu
set Up menu
Parental menu
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Parental Menu
Parental menu
SunBriteTV Model 4660HD Operator’s Manual
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting On-Screen Displays – Parental Menu
Parental menu
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Ratings / Aspect Ratio
Ratings
Aspect Ratio
aspect ratio availability list
1. Analog Channels - Full, 4:3
2. Digital Channels - Full, 4:3
3. AV1 and AV2 (CVBS/S-Video) - Full, 4:3
4. YPbPr1 and YPbPr2 - Full, 4:3
5. VGA - N/A
6. HDMI1, HDMI2, HDMI3 - Full, 4:3
SunBriteTV Model 4660HD Operator’s Manual
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Captioning
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Shortcuts to Browsing Channels
SunBriteTV Model 4660HD Operator’s Manual
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Shortcuts to Browsing Channels
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
Preset Modes Explained
SunBriteTV Model 4660HD Operator’s Manual
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
SunBriteTV Model 4660HD Operator’s Manual
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Care of SunBriteTV
Caring for the LCD Panel:
1. Cleaning the lCD Panel:
Gently wipe the surface of the display panel with a soft cloth (cotton or flannel is best). Be sure the cloth is clean and does
not contain liquid cleaners or other chemicals.
If the LCD panel is very dirty, use a soft damp (with water only) cloth to gently clean the panel.
2. When the TV is not in use, keep it covered with the sunBriteTV Outdoor Dust Cover
The fitted dust cover is designed to protect the LCD panel from the harmful UV rays from direct sunlight, and keeps wind-
blown objects from scratching the surface of the panel.
To order a replacement Dust Cover, contact your Authorized SunBriteTV dealer or SunBriteTV’s Customer Service at
866.357.8688.
General Cleaning
Remove any dirt and salt deposits from the cabinet, being careful to rinse the cloth frequently to avoid scratching the TV or screen
surface. Avoid using harsh chemicals, abrasives, or solvents when cleaning any surface on the unit.
Snow and Ice
Use a soft brush and towel to remove snow and ice from the unit.
Fiber Filter- In areas where dust or salt air is prevalent, it is recommended that the Fiber Filter be cleaned regularly.
There are four Fiber Filters located on the back of the unit, that cover the vent openings. There are two Fiber Filters on the top of the
unit, and two on the bottom of the TV (Figure 1).
CaUTiOn! neVer sPray Or DireCT a HOse inTO THe VenT OPening OF THe TV.
1. To clean the Fiber Filter, unscrew the Filter Holder (Figure 2), and lift the Filter Holder out of the TV (Figure 3).
2. Pull the Fiber Filter out of the Filter Holder (Figure 4).
3. Clean by removing the filter and washing with warm soapy water. Allow to completely air dry overnight prior to reinstalling.
(Do not compress or squeeze filter as it will break down it’s cellular structure.)
To Order replacement Filters, contact your Authorized SunBriteTV Dealer or SunBriteTV’s Customer Service at 866-357-8688.
4. Put the Fiber Filter back up into the Filter Holder and place the Filter Holder back into the TV. Screw securely.
Figure 1
Filter Holder Screws
Figure 2
Fiber Filter
Figure 3
Figure 4
Filter Holder Screws
Fiber Filter
SunBriteTV Model 4660HD Operator’s Manual
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
specifications for sunBriteTV model 4660HD
LCD Screen
46-inch Diagonal TFT Active Matrix
1920 x 1080 full-HD 1080p
16:9
Side View
Front View
Resolution
Aspect Ratio
Contrast Ratio
Viewing Angle
Response Time
TV formats
4000:1
176o x 176o
8.0 milliseconds
1080p, 1080i, 720p, 480p, 480i
Anti-Reflective Window Not Applicable
Input Connectors:
RF
Antenna/CATV (ATSC/QAM/NTSC) x1
HDMI
HDMI™ Input x4
Dimensions with detachable speaker module.
All measurements are in inches
Video Composite
Video Component
S-Video x1 and Composite Video x1, L/R Audio Inputs x1
YPbPr plus Stereo Audio x2
PC
15-pin D-sub VGA plus Stereo Audio
Control Set
Discrete IR (Sony TV IR Code Set),
Concealed IR Window
Audio Out
TosLink Digital Optical x1, Analog 1/8”Headphone Jack
20-Watt Built-in Speakers
Speakers
Exterior
Outdoor-rated ASA Plastic Resin
Input Power
Operating Temp.
100-240 VAC, 50-60 Hz 2.8 A Max
-10o to 122o F. (-23o to 50o C.) *
-10o to 140o F. (-23o to 60o C.)
Non-op. Temp.
Heater Board
Not Applicable
Accessories Included
TV Dimensions
Shipping Dimensions
Weight
Weather-Proof Remote Control, outdoor dust cover
45.51” W x 29.13 ”H x 6.68”D
52”W x 42”H x 13”D
65.0 lbs.
Shipping Weight
Warranty
113.0 lbs.
Two-year residential, in-factory, parts and labor
Specifications are subject to change.
*Temperature range is for operation in shaded location.
PC Timing Codes
800x600 @ 60
1024x768 @ 60
1280x1024 @ 60
1366x768 @ 60
1920x1080 @ 60 (native)
1600x1200 @ 60
Page 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Features Information and Instructions
internal Climatic Control
If temperatures below -10O F. are expected, we recommend that you bring your SunBriteTV inside to prevent damage to the LCD screen.
Programming Other manufacturers’ Universal remote Control Devices
When programming a DirectTV, local cable universal remote control or Control system, you may find that SunBriteTV may not be on the
list of TV manufacturers. If that is the case, Model 4660HD supports SONY’s universal remote code.
sunBriteTV Pixel Quality Policy
SunBriteTV’s Pixel Quality Policy
(Applicable to LCD TVs sold within USA and Canada only.)
SunBriteTVTM LCD screens are manufactured with rigorous standards to maintain optimal viewing. However, the LCD screen may
have minor defects that appear as a small bright or dark pixel. This is common to all LCD screens used in display and television
products, and is not specific to SunBriteTV.
Bright dots are dots that appear bright and unchanged in size when a LCD TV screen displays a black pattern.
Dark dots are dots that appear dark and unchanged in size when a LCD TV screen displays a pure red, green, or blue pattern.
Adjacent dots are pixels located directly next to each other.
Your SunBriteTV will be replaced under warranty if it meets one of the following criteria:
—A total of 7 defective pixels, including both bright dots and dark dots are present. (Model 4660HD LCD TV screen has over a million
pixels.)
—2 or more pairs of adjacent bright dots are present.
—3 adjacent bright dots are present.
—3 adjacent dark dots are present.
To locate defective pixels, the LCD panel should be examined under normal operating conditions, in its native display resolution,
with a 90 degree viewing angle, from a distance of a approximately 20 inches.
To qualify for replacement, a defective LCD screen must be reported to SunBriteTV within 14 days from the day the customer
receives the TV.
For questions, please call our toll-free service number at 866.357.8688.
SunBriteTV Model 4660HD Operator’s Manual
Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
IR Emitter Installation
IR Window
Tie-Down
To install the ir emitter:
The photo to the right shows an IR Emitter* installed.
The end of the Emitter is to be mounted in front of
the IR Emitter Window.
Place the emitter on the white tie-down block and
use the tie-down to secure it in place.
Place the emitter cable over the right or left side
of the cable box and connect the other end of the
emitter to the appropriate control block*.
* Neither the emitter or control block are supplied by
SunBriteTV. See instructions that come with your IR
Emitter and control block to determine how to make the
connections.
Tie-Down Block
IR Emitter
Place IR Emitter Cable
over right or left side of
the cable box.
Page 42
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is left blank intentionally.
SunBriteTV Model 4660HD Operator’s Manual
Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|