P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Introduction
Congratulations on purchasing a Symbol Technologies’ PDT 8100 Series
®
Terminal with Windows Mobile 2003 Software for Pocket PCs! Its unique
combination of features make this product superior for use in a wide range
of applications. These features include:
•
•
•
•
Intel XScale application processor technology
Personal Information Management software
®
®
Microsoft Windows Mobile 2003 Software operating system
®
RF communication via Symbol’s Spectrum24 Wireless Local Area
Network (WLAN PDT 814x)
•
•
1-Dimensional laser scanning capability
Color TFT LCD display
28-key, 37-key, or 47-key keyboard
“Quick Grip” Trigger Handle Interface
Touch screen
•
•
•
•
•
•
Printing support
IrDA-compliant interface for printing and communications.
About This Guide
covered include:
•
•
•
•
•
•
•
•
•
Accessories on page 2
Parts of the Terminal on page 3
Getting Started on page 5
Inserting a Compact Flash Card on page 5
Removing a Compact Flash Card on page 6
Installing the 1950 mAh Battery on page 7
Charging the Battery on page 8
15-Pin Serial Port Connector on page 9
Attaching the Trigger Handle (“Quick Grip” compatible terminals
only) on page 9
•
•
•
•
Attaching the Handstrap on page 10
Starting the Terminal on page 10
Aligning the Screen on page 11
Initiating a Network Connection on page 11
1
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
M
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
b
i
l
e
P
o
c
k
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Controlling the Backlight on page 11
Using a Headset on page 12
Using the Keyboard on page 13
Using the Stylus on page 19
Today Screen on page 19
Navigation Bar and Command Bar on page 20
Input Methods on page 20
Scanning on page 23
Capturing Still Images on page 24
Resetting Your Terminal on page 25
Host Communications on page 26
Maintaining the Terminal on page 27
Troubleshooting on page 28
End-user License Agreement on page 34
Regulatory Information on page 37
Warranty
Service Information.
The PDT 8100 Series with Windows Mobile 2003 Software for Pocket PCs
Product Reference Guide (p/n 72-66325-xx) details the applications
available for the terminal.
For the latest version of the Product Reference Guide, and for Quick
Accessories
Each terminal requires one 1950 mAh lithium-ion battery. The following
optional accessories are available from Symbol Technologies:
•
Cables
•
•
•
•
•
•
•
•
•
Headset
-
-
-
-
Serial/Charging cable
IrDA compliant printers
Magnetic stripe reader
Serial charging cradle
DEX cable
Autocharge cable
Snap-on printer cables
Single-slot modem and charging cradle
Snap on “Quick Grip” Trigger Handle
Stylus for performing pen functions
UBC battery adapters
•
•
•
•
Carrying case
Clip on modem module
Four-slot charging only cradle
Four-slot Ethernet cradle
Vehicle cradle
2
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Parts of the Terminal (continued)
BACK VIEW
Stylus
Speaker
Handstrap
clip
IrDA port
Stylus silo
Reset button
Battery cover
switch
Battery lock
Battery
switch
compartment
Flash card
cover
Lithium-ion
battery
Battery door
Battery door
latches
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Parts of the Terminal (continued)
TOP VIEW
Exit Window
(terminals with
scanner/imager)
15-Pin Serial Port
(terminals without
scanner)
BOTTOM VIEW
Serial port
Getting Started
Before you can use your terminal, perform these basic setup procedures:
•
•
•
•
Insert the Compact Flash card (optional).
Install and charge the battery.
Start the terminal.
Initiate the network connection (PDT 814x only).
Inserting a Compact Flash Card
The terminal contains a slot for a standard compact flash card, which
includes a locking mechanism that prevents the card from coming loose if
the terminal is dropped. Insert the compact flash card carefully to ensure it
engages this locking mechanism.
1. Open the battery door and remove the battery.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
2. Remove the flash card cover at the top of the battery compartment
by pulling the top out, and lifting the cover up.
3. Insert the flash card into the compartment with the pins facing for-
ward, and the main label facing down. It only fits one way. The two
metal tabs on the locking mechanism will prevent you from pushing
the card all the way in.
Pull top out & lift cover
Insert flash
card
Compact flash
card cover
4. To fit the card into place, push down and in at the same time, so that
the lip of the compact flash card slips under the tabs of the locking
mechanism.
5. Replace the flash card cover by inserting the bottom first, and press-
ing the top in.
Note:
After you insert or remove a compact flash card, you must re-
place the flash card cover or the terminal will not function.
6. Reinsert the battery and battery door.
7. Perform a soft reset (see Performing a Soft Reset on page 25).
Removing a Compact Flash Card
1. Open the battery door and remove the battery and flash card cover.
2. Use the stylus to press the flash card release button inside the flash
card compartment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Charging the Battery
Charging the Main Battery and Memory Backup Battery for
the First Time
Before using your terminal for the first time, charge the lithium-ion battery
in the terminal for a minimum of 12 hours, with the terminal off. Charge the
battery using the Serial/Charging Cable or the appropriate cradle. This is
the time needed to fully charge the main battery and the internal backup
battery in a terminal that is off.
Recharging the Main Battery
To recharge the 1950 mAh lithium-ion battery in the terminal, turn the
terminal off and charge the battery for approximately 2 1/2 hours using the
Serial/Charging Cable or the appropriate cradle.
Note:
The battery can also be recharged separately in the CRD
8100-1200S Single Slot Charging Cradle, VCD 8100-R001
Vehicle Charging Cradle, or UBC battery adapter.
Charging the Battery Using a Cradle
Charge the battery in the terminal using the CHS 8100-4000C Four Slot
Charge Cradle, CRD 8100-1200M Single Slot Modem Cradle, VCD 8100-
R001 Vehicle Charging Cradle, CRD 8100-1200S Single Slot Charging
Cradle, or CRD 8100-4000E Four Slot Ethernet Cradle. For more
information, refer to the set up instructions in the respective Quick
Reference Guides.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Charging the Battery Using the Serial/Charging Cable
1. Insert the battery
charging receptacle
into the bottom of the
terminal.
2. Plug the power cable
into a wall outlet.
3. Plug the other end of
the power cable into
Battery charging
receptacle
the battery charging re-
ceptacle.
Serial/Charging Cable
15-Pin Serial Port Connector
To connect to the Micro-D RS-232 port at the top of the terminal, use an
ITT Cannon brand mil-spec connector (MDM-15SSB) with captivated jack
screws (mil p/n M83513/5-6) to protect the connector’s contacts from
damage during insertion and removal.
Attaching the Trigger Handle
(“Quick Grip” compatible terminals only)
For information about attaching and using the scanning Trigger Handle,
refer to the TRG 8100 Trigger Handle Quick Reference Guide
(p/n 72-55949-xx). Please note that the trigger handle does not ship with
the terminal.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Attaching the Handstrap
3
1
2
Starting the Terminal
Press the red Power button to turn the terminal on and off.
Power button
As the terminal initializes its Flash File System, the Symbol splash screen
displays for about 30 seconds.
When the Welcome screen appears, tap anywhere on the screen to
continue to the Align screen. Note that these screens also appear every
time you perform a hard reset.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Aligning the Screen
To align your terminal so the cursor on the touch screen aligns with the tip
of your stylus:
1. Remove the stylus from its storage silo on the back of the terminal.
2. Tap the center of each target that appears on the screen with the tip
of the stylus.
Tap the target firmly and accurately at
each location on the screen. The target
will continue to move until the screen
is aligned.
3. Follow the directions on the screen which explain how to use the sty-
lus and pop-up menus, and allow you to set your city and time zone.
Initiating a Network Connection
Before using the terminal, set up the Spectrum24 network connection.
Refer to the PDT 8100 Series with Windows Mobile 2003 Software for
Pocket PCs Product Reference Guide for setup instructions.
Controlling the Backlight
Press the Backlight button to turn the display and keyboard backlights on
and off. Press once to turn the display backlight on, press again to turn the
keyboard backlight on, and press a third time to turn both backlights off.
Power button
Backlight button
11
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Adjusting the Backlight
Keyboard
Keys
Description
28-key
Function + “1”
Function + “2”
Decrease display backlight (decrease brightness)
Increase display backlight (increase brightness)
37-key
47-key
Function + “G” Decrease display backlight (decrease brightness)
Function + “I” Increase display backlight (increase brightness)
Function + “Y” Decrease display backlight (decrease brightness)
Function + “W” Increase display backlight (increase brightness)
Note: Backlight adjustments can be made on displays only (and are also adjust-
able via software). Keyboard backlights cannot be adjusted.
Using a Headset
The terminal is equipped with an audio
connector and a headset may be
installed for telephony operation.
To use the headset (p/n 50-11300-050),
plug the headset jack into the audio
connector on the side of the terminal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Using the Keyboard
Note:
Key functions can be changed by an application. Your key-
board may not function exactly as described. For more de-
tailed keyboard information, refer to the PDT 8100 Series with
Windows Mobile 2003 Software for Pocket PCs Product Ref-
erence Guide.
Using the 28-Key Keyboard
The 28-key keyboard uses an alphanumeric keypad that produces the 26-
character alphabet (A-Z), numbers (0-9), and assorted characters. The
keyboard is color-coded to indicate which modifier key (Alpha-Numeric,
Func) to press to produce a particular character or action. The keyboard
default is numeric.
Cursor keys
Caps/Shift key
Space/
Backspace key
End key
Send key
Scan key
Scan key
Home
Clear key
Page up &
down keys
Tab key
Alpha key
Enter/Escape
key
Function key
Control key
Alt key
Backlight button
Power button
13
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Key
Action
Note:
1. Press Func, then another key to produce the value or function above that
key. See individual key descriptions in this table for additional Function key
usage.
2.Press Func + Ctrl + Clear to close applications.
Alpha
Press Alpha to toggle between alpha and numeric
mode. In alpha mode, pressing a key produces the yel-
low letter on that key; in numeric mode, pressing a key
produces the number in gray.
Backlight
See Controlling the Backlight on page 11.
Caps/Shift
Press Shift when in alpha mode, then another key to
capitalize the letter on that key.
Press Func + Shift to toggle All Caps on and off.
Clear
Press Clear to generate an Escape key. This is applica-
tion dependent but typically closes a window or clears
the screen.
Cursor
Press cursor keys to move the cursor left, right, up and
down on the screen.
Press Func + up cursor to raise the volume.
Press Func + down cursor to lower the volume.
End
Press End to generate an End key. This is application
dependent but typically moves the cursor to the end of a
line
Enter/Escape
Press Enter after entering data or a command.
Press Func + Enter to generate an Escape key. This is
application dependent but typically closes a window or
clears the screen.
Power
Scan
See Starting the Terminal on page 10.
Press Scan to scan bar codes. (Also use right and left
scan triggers.)
Send
The Send key is application dependent.
Space/Back-
space
Press Func + Bk-Sp to enter a blank space.
Press Bk-Sp to erase information entered on the display,
one character at a time.
Tab
Press Tab to generate a Tab key. This is application de-
pendent but typically moves the cursor from field to field.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Using the 37-Key Keyboard
The 37-key keyboard uses an alphanumeric keypad that produces the 26-
character alphabet (A-Z), numbers (0-9), and assorted characters. The
keyboard is color-coded to indicate which modifier key (Alpha-Numeric,
Func) to press to produce a particular character or action. The keyboard
default is numeric, producing the gray number or white character on that
key.
Scan key
Cursor keys
(C, G, H, I)
Caps/Shift key
End key
Space/
Backspace key
Send key
Clear key
Function key
Alt key
Tab key
Volume (+) key
Control key
Alpha key
Volume (-) key
Backlight button
Enter/Escape
key
Power button
15
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Key
Action
Note:
1.Press Func, then another key to produce the value or function above that
key. See individual key descriptions in this table for additional Function key
usage.
2.Press Func + Ctrl + Clear to close applications.
Alpha
Press Alpha to toggle between alpha and numeric
mode. In alpha mode, pressing a key produces the yel-
low letter on that key; in numeric mode, pressing a key
produces the number in gray or character in white.
Backlight
See Controlling the Backlight on page 11.
Caps/Shift
Press Shift when in alpha mode, then another key to
capitalize the letter on that key.
Press Func + Shift to toggle All Caps on and off.
Clear
Press Clear to generate an Escape key. This is applica-
tion dependent but typically closes a window or clears
the screen.
Cursor keys:
C, G, H, I
Press Func + a cursor key to move the cursor up, down,
left, and right on the screen.
End
Press End to generate an End key. This is application
dependent but typically moves the cursor to the end of a
line
Enter/Escape
Press Enter after entering data or a command.
Press Func + Enter to generate an Escape key. This is
application dependent but typically closes a window or
clears the screen.
Power
Scan
See Starting the Terminal on page 10.
Press Scan to scan bar codes. (Also use right and left
scan triggers.)
Send
The Send key is application dependent.
Space/Back-
space
Press Func + Bk-Sp to enter a blank space.
Press Bk-Sp to erase information entered on the display,
one character at a time.
Tab
Press Tab to generate a Tab key. This is application de-
pendent but typically moves the cursor from field to field.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Using the 47-Key Keyboard
The 47-key keyboard uses an alphanumeric keypad that produces the 26-
character alphabet (A-Z), numbers (0-9), and assorted characters. The
keyboard is color-coded to indicate which modifier key (Alpha-Numeric,
Func) to press to produce a particular character or action. The keyboard
default is the key value, producing the gray number or lower case yellow
letter on that key.
Cursor keys
(C, G, H, I)
Scan key
Caps/Shift key
End key
Space/
Backspace
key
Send key
Function key
Alt key
Clear key
Tab key
Volume (+) & (-)
keys
Control key
Enter/Escape
key
Power button
Backlight button
17
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Key
Action
Note:
1. Press Func, then another key to produce the value or function above that
key. See individual key descriptions in this table for additional Function key
usage.
2.Press Func + Ctrl + Clear to close applications.
Backlight
See Controlling the Backlight on page 11.
Caps/Shift
Press Shift when in alpha mode, then another key to
capitalize the letter on that key.
Press Func + Shift to toggle All Caps on and off.
Clear
Press Clear to generate an Escape key. This is applica-
tion dependent but typically closes a window or clears
the screen.
Cursor keys:
C, G, H, I
Press Func + a cursor key to move the cursor up, down,
left, and right on the screen.
End
Press End to generate an End key. This is application
dependent but typically moves the cursor to the end of a
line
Enter/Escape
Press Enter after entering data or a command.
Press Func + Enter to generate an Escape key. This is
application dependent but typically closes a window or
clears the screen.
Power
Scan
See Starting the Terminal on page 10.
Press Scan to scan bar codes. (Also use right and left
scan triggers.)
Send
The Send key is application dependent.
Space/Back-
space
Press Func + Bk-Sp to enter a blank space.
Press Bk-Sp to erase information entered on the display,
one character at a time.
Tab
Press Tab to generate a Tab key. This is application de-
pendent but typically moves the cursor from field to field.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Using the Stylus
Use the stylus as a mouse to select items and enter information.
•
•
•
Tap: Touch the screen once with the stylus to open items and select
options.
Drag: Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple items.
Tap-and-hold: Tap and hold the stylus on an item to see a list of ac-
tions available for that item. On the pop-up menu that appears, tap
the action you want to perform.
Today Screen
When you turn on your terminal for the first time each day (or after four
hours of inactivity), the Today screen appears. You can also display it by
tapping
, then Today. On the Today screen, you can see important
information for the day.
Tap to switch
to a program
Tap to change volume
or mute all sounds
Tap to change date and time
Tap to open an item
Your day at a glance
Tap to create
a new item
Tap to view connection status
19
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Navigation Bar and Command Bar
The navigation bar at the top of the screen displays the active program and
current time, and allows you to select programs and close screens. The
command bar at the bottom of the screen contains menus and buttons to
perform tasks in programs.
Tap to change the volume
or mute the device
Tap to quickly select a program you
have recently used
Tap to select a program
Tap to see additional programs
Tap to customize the device
Input panel button
New button
Menu Buttons
names
Input Methods
Enter information in any program by typing with the 28-, 37-, or 47-key
keyboard, or use the input panel to type with the soft keyboard, write using
Block Recognizer, Letter Recognizer, or Transcriber. In any case, the
characters appear as typed text on the screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
To show or hide the input panel, tap the Input Panel button. Tap the arrow
next to this button to view input methods.
Select input method settings
Select an input method
Tap to see your choices
Input Panel button
When you use the input panel, your terminal anticipates the word you are
typing or writing and displays it above the input panel. When you tap the
displayed word, it is inserted into your text at the insertion point. The more
you use your terminal, the more words it learns to anticipate.
Using the Soft Keyboard
1. Tap the arrow next to the Input Panel button, then Keyboard.
2. On the soft keyboard, tap the keys with your stylus.
Tap here if this is
the right word
Using the Block Recognizer
1. Tap the arrow next to the Input Panel button, then Block Recognizer.
2. Write a letter in the left side of the box, or a number in the right side,
using special character strokes.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
When you write a letter, it is converted to typed text on the screen. For
instructions on entering Block Recognizer characters, with Block
Recognizer open, tap the question mark next to the writing area, or see
Block Recognizer Characters on page 22.
Using the Letter Recognizer
1. Tap the arrow next to the Input Panel button, then Letter Recognizer.
2. Write letters or numbers in the writing area, just as you would on pa-
per. Write capital letters in the left side of the box, numbers in the
right side, and lower case letters in the center.
When you write a letter, it is converted to typed text on the screen. For
instructions on using Letter Recognizer, with Letter Recognizer open, tap
the question mark next to the writing area.
Using the Transcriber
1. Tap the arrow next to the Input Panel button, then Transcriber.
2. Write anywhere on the screen. What you write on the screen will be
converted to text.
Block Recognizer Characters
The following chart is a partial display of the characters you can write while
using the Block Recognizer (the dot on each character is the starting point
for writing).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Scanning
Terminals with an integrated laser scanner allow you to collect data by
scanning 1-dimensional bar codes.
Terminals with an integrated imager allow you to collect data by scanning
1-dimensional bar codes (including RSS) and 2-dimensional bar codes
(including PDF417 and DataMatrix).
Note:
Additional Symbologies for imager scanning will be supported
in the near future.
Before using the terminal to scan bar codes, ensure the scanner is
initialized. Refer to the PDT 8100 Series with Windows Mobile 2003
Software for Pocket PCs Product Reference Guide for information on
configuring your terminal for scanning.
To scan bar codes:
1. Aim the exit window at the bar code.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
2. Press either the right, left, or center scan trigger. (Center scan trig-
gers vary with keypad types.)
-
For terminals with a laser scanner, ensure the red scan beam
covers the entire bar code. The green scan LED lights and a
beep sounds to indicate a successful decode.
-
For terminals with an imager, center the target cross hairs in the
center of the bar code. The entire symbol must be within the
brackets. The green scan LED lights and a beep sounds to indi-
cate a successful decode.
Linear bar code
PDF417 symbol
Symbol
Aiming Pattern
3. Release the scan trigger.
Capturing Still Images
In addition to scanning, terminals with an integrated imager allow you to
capture still images (depending on the software installed).
Capturing still images on the terminal is application dependent. However,
you can capture still images using the demo applications supplied with the
terminal.
For detailed information about launching and using Imager Demo
(platform) and Imager Sample (application), refer to the PDT 8100 Series
with Windows Mobile 2003 Software for Pocket PCs Product Reference
Guide.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Resetting Your Terminal
If your terminal stops responding to input, reset it.
Performing a Soft Reset
A soft reset restarts the terminal and saves all stored records and entries.
To perform a soft reset press and hold the Power button (for approximately
five seconds) and release it as soon as the screen changes and the
terminal begins to reboot.
Caution:
Files that remain open during a soft reset may not be retained.
As an alternate method to perform a soft reset when the terminal is on
press the key combinations in the table below.
Keyboard
28-key
Keys
Press Backlight + Down Arrow + Function.
Press Backlight + Alpha + Function.
Press Backlight + End + Function.
37-key
47-key
Performing a Hard Reset
A hard reset also restarts your terminal, but can erase all files and settings
not stored in the Flash File System. Therefore, never perform a hard reset
unless a soft reset does not solve your problem.
Note:
You can restore any data previously synchronized with your
computer during the next ActiveSync operation. Refer to the
PDT 8100 Series with Windows Mobile 2003 Software for
Pocket PCs Product Reference Guide.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
To perform a hard reset on the terminal:
1. Remove the battery cover.
2. While holding down the Function key, use the stylus (or similar ob-
ject without a sharp tip) to gently press the reset button.
Func Key
(37-key
keyboard
pictured)
Reset
Button
3. Replace the battery cover and press the Power button.
4. As the terminal reboots, the Symbol splash screen displays for about
30 seconds.
5. Realign the screen as described on page 11.
Note:
With a hard reset, Formats, Preferences, and other settings
are restored to their factory default settings.
Host Communications
The terminal can communicate with a host PC either directly through its
communications port using an RS-232 serial cable, the cradle, or
wirelessly via the Spectrum24 wireless LANs. For more information on
setting up and performing wireless communications with your terminal,
refer to the PDT 8100 Series with Windows Mobile 2003 Software for
Pocket PCs Product Reference Guide.
Using the RS-232 Serial Cable
To connect the RS-232 serial cable for host communication:
1. Connect the RS-232 serial communication cable’s connector to the
adapter cable’s connector.
2. Plug the adapter cable’s subminiature connector into the serial com-
munication port on the bottom of the terminal.
3. Plug the other end of the RS-232 serial communication cable into
the host PC.
4. Begin host communication as specified by your application.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Using the Cradle
To communicate through the cradle:
1. Ensure all connections between the cradle and the host computer
are secure. Refer to the Quick Reference Guide that shipped with
your cradle for instructions on setting up the cradle.
2. Power on the host computer, the cradle, and the terminal.
3. Insert the terminal into the cradle.
4. Begin host communications as specified by your application.
Communicating with Printers
To print from a standard printer:
1. Attach an RS-232 serial cable to the serial port in the bottom of the
terminal.
2. Attach the other end of the cable to the serial port on the printer.
3. Run your application’s print function.
To print from an IrDA-compliant printer:
1. Point the IrDA port on the back of the terminal at the IrDA port on the
printer, at a maximum distance of 39 inches (1 meter).
2. Run the application’s print function.
Note:
The terminal must have software configured to communicate
with the printer you are using.
Maintaining the Terminal
To maintain your terminal in good working order:
•
Do not scratch the screen. Use the supplied stylus or plastic-tipped
pens intended for use with a touch-sensitive screen. Never use a
pen or pencil or other sharp object on the screen.
Although your terminal is water and dust resistant, do not expose it
to rain or moisture for an extended period of time. Treat your terminal
as you would a pocket calculator or other small electronic instru-
ment.
•
•
•
The touch-sensitive screen of your terminal contains glass. Do not
drop your terminal or subject it to strong impact.
Protect your terminal from temperature extremes. Do not leave it on
the dashboard of a car on a hot day, and keep it away from heat
sources.
•
Do not store or use your terminal in any location that is extremely
dusty, damp or wet.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
•
If the surface of the terminal screen becomes soiled, clean it with a
soft cloth moistened with a diluted window-cleaning solution.
Troubleshooting
Problem
Cause
Solution
Terminaldoesnot
turn on.
Lithium-ion bat-
tery not charged.
Charge or replace the lithium-ion
battery in the terminal.
Lithium-ion bat-
tery not installed
properly.
Ensure battery is installed properly.
System crash.
Perform a soft reset. If the terminal
still does not turn on, perform a
hard reset. See Resetting Your
Terminal on page 25.
Rechargeable
lithium-ion bat-
tery did not
charge.
Battery failed.
Replace battery. If your terminal
still does not operate, try a soft re-
set, then a hard reset; see Reset-
ting Your Terminal on page 25.
Terminal re-
Insert terminal in cradle and begin
charging. The 1950 mAh lithium-
ion battery requires up to 2 1/2
hours to recharge fully.
moved from cra-
dle while battery
was charging.
Cannot see char-
acters on display.
Terminal not pow-
ered on.
Press the Power button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Problem
Cause
Solution
Fail to communi-
cate with IrDA
printer.
Distance from
printer is more
than 1 meter (39
inches).
Bring the terminal closer to the
printer and attempt communica-
tions again.
Obstruction inter-
fered with com-
munication.
Check the path to ensure no ob-
jects were in the way.
Application is not
enabled to run
IrDA printing.
Printer support must be included
with the application to run IrDA
printing on the terminal. See your
System Administrator.
During data com-
munication, no
data was trans-
mitted, or trans-
mitted data was
incomplete.
Terminal re-
Replace the terminal in the cradle,
or replace the Synchronization ca-
ble, and re-transmit.
moved from cra-
dle or unplugged
from host PC dur-
ing communica-
tions.
Incorrect cable
configuration.
See your System Administrator.
Communication
software was in-
correctly installed
or configured.
Perform setup as described in the
PDT 8100 Series with Windows
Mobile 2003 Software for Pocket
PCs Product Reference Guide.
No sound is audi-
ble.
Volume setting is
low or turned off.
Check the System Volume slider in
the Sounds & Reminders proper-
ties dialog box (under Start/Set-
tings) to ensure the volume is not
turned down.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Problem
Cause
Solution
Terminal turns it-
self off.
Terminal is inac-
tive.
Your terminal turns off after a peri-
od of inactivity. If the terminal is
running on battery power, this peri-
od can be set from 1 to 5 minutes,
in one-minute intervals. If the ter-
minal is running on external power,
this period can be set to 1, 2, 5, 10,
15, and 30 minutes.
Check the Powerdialog box (in the
System tab under Start/Settings),
and change the setting if you need
a longer delay before the automat-
ic shutoff feature activates.
Battery is deplet-
ed.
Replace the battery.
Battery cover is
removed.
Replace the battery door.
Terminal doesn’t
recognize my
handwriting.
Character strokes
written incorrectly
with the stylus.
If you’re using the Block Recogniz-
er input method, characters must
be written a certain way. Refer to
the PDT 8100 Series with Win-
dows Mobile 2003 Software for
Pocket PCs Product Reference
Guide for information about how to
write character strokes.
Character strokes
written on the
wrong part of the
LCD screen.
If you’re using the Block Recogniz-
er or Letter Recognizer input meth-
od, make the character strokes in
the lower character entry area on
the screen — not on the display
part of the screen.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Problem
Cause
Solution
Lower- case and
upper-case let-
ters, and numbers
written on the
Ensure you are writing letters and
numbers in the appropriate section
of the writing area.
wrong parts of the
LCD screen.
Tapping the
LCD screen not
aligned correctly.
Align the screen. Choose Screen/
Align Screenfrom the System tab
underStart/Settings, or hold down
the Function button and press the
Action button.
screen buttons or
icons does not
activate the cor-
responding fea-
ture.
The system is
hung.
Soft reset the system. To perform a
soft reset, see Resetting Your Ter-
minal on page 25.
A message ap-
pears stating that
your terminal
Too many files
stored on the ter-
minal.
Delete unused memos and
records. You can save these
records on your computer.
memory is full.
Too many applica-
tions installed on
the terminal.
If you have installed additional ap-
plications on your terminal, remove
them to recover memory. Select
Start, then Settings, and select
the System tab. Tap Remove Pro-
grams, select the unused program
and tap Remove.
Beamed data
does not trans-
mit.
Terminals too
close together.
Confirm that the terminals are 5”
apart, and there is a clear path be-
tween the two devices.
Insufficient room
lighting.
Adjust the room lighting or move to
a different location.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Problem
Cause
Not enough free
memory available
for receiving data.
Solution
Your terminal requires at least
twice the amount of memory avail-
able as the data you are receiving.
For example, if you are receiving a
30K application, you must have at
least 60K free.
When receiving
beamed data an
out of memory
message ap-
pears.
Your terminal
does not accept
scan input.
Scanning applica-
tion is not loaded.
Verify that the unit is loaded with a
scanning application. See your
System Administrator.
Unreadable bar
code.
Be sure the symbol is not defaced.
Distance be-
Be sure you are within proper
scanning range.
tween exitwindow
and bar code is in-
correct.
Terminal is not
programmed for
the bar code.
Be sure the terminal is pro-
grammed to accept the type of bar
code you are scanning.
Terminal is not
programmed to
generate a beep.
If you are expecting a beep on a
good decode and don’t hear one,
check that the application is set to
generate a beep on good decode.
Battery is low.
If the scanner stops emitting a la-
ser beam when you press the trig-
ger, check your battery level.
Note: If the scanner is still not
reading symbols, contact your dis-
tributor or Symbol Technologies.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Problem
Cause
Solution
Terminals with an integrated imager:
The terminal
does not save im-
ages.
The still Image
Capture program
is not enabled.
Enable Image Capture.
The still Image Capture program is
application dependent. To enable
the ImageDemo application, select
ImageDemo from the Start menu.
Tap the Snap button (in Capture
mode) or press the scan trigger to
enable the ImageDemo.
Aim Target or Illu-
mination is not
available.
Aim or Illumina-
tion may be
turned off.
Enable Aim or Illumination.
The still Image Capture program is
application dependent. To enable
the Aim and Illumination features in
the ImageDemo application, select
ImageDemo from the Start menu.
Select Capture from the Mode
menu. Tap the Aim and/or Illumina-
tion check boxes to enable.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
End-user License Agreement
•
You have acquired a device (“DEVICE”) that includes software licensed by Symbol
from Microsoft Licensing Inc. or its affiliates (“MS”). Those installed software products
of MS origin, as well as associated media, printed materials, and “online” or electronic
documentation (“SOFTWARE”) are protected by international intellectual property
laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
SOFTWARE includes software already installed on the DEVICE (“DEVICE Software”)
and MS software contained on the CD-ROM disk (“Companion CD”).
•
IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT ("EULA"),
DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY
CONTACT SYMBOL FOR INSTRUCTIONS ON RETURN OF THE UNUSED
DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT
NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT
TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).
GRANT OF SOFTWARE LICENSE. This EULA grants you the following license:
•
•
DEVICE Software. You may use the DEVICE Software as installed on the DEVICE.
COMPANION CD. A Companion CD is included with your DEVICE, and you may
install and use the Microsoft® ActiveSync® 3.7 component on one (1) or more
computers to exchange information with one (1) or more computing devices that
contain a compatible version of the Microsoft® Pocket PC Software 2002 operating
system. For other software component(s) contained on the Companion CD, you may
install and use such components only in accordance with the terms of the printed or
online end user license agreement(s) provided with such component(s). In the
absence of an end user license agreement for particular component(s) of the
Companion CD, you may install and use only one (1) copy of such component(s) on
the DEVICE or a single computer with which you use the DEVICE.
•
•
Microsoft® Outlook® 2002. If Microsoft Outlook 2002 is included with your DEVICE,
the following terms apply to your use of Microsoft Outlook 2002: (i) regardless of the
information contained in the “Software Installation and Use” section of the online
EULA you may install one (1) copy of Microsoft Outlook 2002 on one (1) computer to
use, exchange data, share data, access and interact with the DEVICE, and (ii) the
EULA for Microsoft Outlook 2002 is between Symbol and the end user - not between
the PC manufacturer and end user.
Security Updates/Digital Rights Management. Content providers are using the
digital rights management technology contained in this SOFTWARE (“DRM”) to
protect the integrity of their content (“Secure Content”) so that their intellectual
property, including copyright, in such content is not misappropriated. Portions of this
SOFTWARE and third party applications such as media players use DRM to play
Secure Content (“DRM Software”). If the DRM SOFTWARE's security has been
compromised, owners of Secure Content (“Secure Content Owners”) may request
that MS revoke the DRM SOFTWARE's right to copy, display and/or play Secure
Content. Revocation does not alter the DRM SOFTWARE's ability to play unprotected
content. A list of revoked DRM SOFTWARE is sent to your computer whenever you
download a license for Secure Content from the Internet. You therefore agree that MS
may, in conjunction with such license, also download revocation lists onto your
computer on behalf of Secure Content Owners. MS will not retrieve any personally
identifiable information, or any other information, from your computer by downloading
such revocation lists. Secure Content Owners may also require you to upgrade some
of the DRM components in this SOFTWARE (“DRM Upgrades”) before accessing
their content. When you attempt to play such content, MS DRM SOFTWARE will
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
notify you that a DRM Upgrade is required and then ask for your consent before the
DRM Upgrade is downloaded. Third party DRM Software may do the same. If you
decline the upgrade, you will not be able to access content that requires the DRM
Upgrade; however, you will still be able to access unprotected content and Secure
Content that does not require the upgrade.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
•
Speech/Handwriting Recognition. If the SOFTWARE includes speech and/or
handwriting recognition component(s), you should understand that speech and
handwriting recognition are inherently statistical processes and that errors can occur
in the component's recognition of your handwriting, and the final conversion into text.
Neither Symbol nor its suppliers shall be liable for any damages arising out of errors in
the speech and handwriting recognition process.
•
Limitations on Reverse Engineering, Decompilation and Disassembly. You may
not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to
the extent that such activity is expressly permitted by applicable law notwithstanding
this limitation.
•
•
Single DEVICE. The DEVICE Software is licensed with the DEVICE as a single
integrated product. The DEVICE Software installed in read only memory (“ROM”) of
the DEVICE may only be used as part of the DEVICE.
Single EULA. The package for the DEVICE may contain multiple versions of this
EULA, such as multiple translations and/or multiple media versions (e.g., in the user
documentation and in the software). Even if you receive multiple versions of the
EULA, you are licensed to use only one (1) copy of the DEVICE Software.
NO RENTAL. Except if specifically authorized by Symbol for leased hardware, you
may not rent, lease, or lend the SOFTWARE.
•
APPROVED ADDITIONAL TEXT IF THE DEVICE IS LEASED
LEASED HARDWARE. In the event that you receive the DEVICE under the terms of a lease
from Symbol or Symbol’s third-party representative, the following additional terms shall
apply: (i) you may not transfer the SOFTWARE to another user as part of the transfer of the
DEVICE, whether or not a permanent transfer of the SOFTWARE with the DEVICE is
otherwise allowed in this EULA; (ii) your rights with respect to any SOFTWARE upgrades
shall be as determined by the lease you signed for the DEVICE; and (iii) you may not use
the SOFTWARE after your lease terminates, unless you purchase the DEVICE from
Symbol.]
•
Software Transfer. You may permanently transfer all of your rights under this EULA
only as part of a sale or transfer of the DEVICE, provided you retain no copies, you
transfer all of the SOFTWARE (including all component parts, the media and printed
materials, any upgrades, this EULA and, if applicable, the Certificate(s) of
Authenticity), and the recipient agrees to the terms of this EULA. If the SOFTWARE is
an upgrade, any transfer must include all prior versions of the SOFTWARE.
Termination. Without prejudice to any other rights, Symbol or MS may terminate this
EULA if you fail to comply with the terms and conditions of this EULA. In such event,
you must destroy all copies of the SOFTWARE and all of its component parts.
•
UPGRADES AND RECOVERY MEDIA.
•
DEVICE Software. If the DEVICE Software is provided by Symbol separate from the
DEVICE on media such as a ROM chip, CD ROM disk(s) or via web download or
other means, and is labeled “For Upgrade Purposes Only” you may install one (1)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
copy of such DEVICE Software onto the DEVICE as a replacement copy for the
existing DEVICE Software, and use it in accordance with this EULA.
•
COMPANION CD. If any software component(s) is provided by Symbol separate from
the DEVICE on CD ROM disk(s) or via web download or other means, and labeled
“For Upgrade Purposes Only”, you may (i) install and use one (1) copy of such
component(s) on the computer(s) you use to exchange data with the DEVICE as a
replacement copy for the existing Companion CD component(s).
COPYRIGHT. All title and intellectual property rights in and to the SOFTWARE (including
but not limited to any images, photographs, animations, video, audio, music, text and
“applets,” incorporated into the SOFTWARE), the accompanying printed materials, and any
copies of the SOFTWARE, are owned by MS or its suppliers (including Microsoft
Corporation). You may not copy the printed materials accompanying the SOFTWARE. All
title and intellectual property rights in and to the content which may be accessed through
use of the SOFTWARE is the property of the respective content owner and may be
protected by applicable copyright or other intellectual property laws and treaties. This EULA
grants you no rights to use such content. All rights not specifically granted under this EULA
are reserved by MS and its suppliers (including Microsoft Corporation).
EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. export
jurisdiction. You agree to comply with all applicable international and national laws that apply
to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-
user, end-use and destination restrictions issued by U.S. and other governments. For
PRODUCT SUPPORT. Product support for the SOFTWARE is not provided by MS, its
parent corporation, Microsoft Corporation, or their affiliates or subsidiaries. For product
support, please refer to Symbol support number provided in the documentation for the
DEVICE. Should you have any questions concerning this EULA, or if you desire to contact
Symbol for any other reason, please refer to the address provided in the documentation for
the DEVICE.
NO LIABILITY FOR CERTAIN DAMAGES. EXCEPT AS PROHIBITED BY LAW, MS SHALL
HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR
INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY
REMEDY FAILS OF ITS ESSENTIAL PURPOSE.
FOR APPLICABLE LIMITED WARRANTIES AND SPECIAL PROVISIONS PERTAINING
TO YOUR PARTICULAR JURISDICTION, PLEASE REFER TO YOUR WARRANTY
BOOKLET INCLUDED WITH THIS PACKAGE OR PROVIDED WITH THE SOFTWARE
PRINTED MATERIALS.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Battery Information
Symbol rechargeable battery packs are designed and constructed to the highest
standards within the industry.
However, there are limitations to how long your battery can operate or be stored
before needing replacement. Many factors affect the actual life cycle of your battery
pack, such as heat, cold, harsh environmental conditions and severe drops.
When batteries are stored over six (6) months, some irreversible deterioration in
overall battery quality may occur. Store your batteries discharged in a dry, cool place,
removed from the equipment to prevent loss of capacity, rusting of metallic parts and
electrolyte leakage. When storing batteries for one year or longer, they should be
charged and discharged at least once a year. If an electrolyte leakage is observed,
avoid any contact with affected area and properly dispose of the battery.
An indication that your Symbol battery needs replacement is when normal run time
begins to diminish. When you consistently experience significant loss of run time,
replace your battery.
Standard warranty period for all Symbol batteries is 30 days, regardless if the battery
was purchased separately or included as part of the mobile computer or bar code
scanner.
For more information on Symbol batteries, please visit
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to ensure
that you are adhering to your company’s safety programs to prevent employee injury.
•
•
•
•
•
•
•
•
•
•
•
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment‘
Improve work procedures.
Regulatory Information
All Symbol devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly
approved by Symbol Technologies, could void the user's authority to operate the
equipment.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Radio Modules
The PDT 8100 series terminals may contain an approved radio module. These
modules are identified below.
•
•
•
PDT 8133:Novatel CDPD Radio Module, Type: NRM-6831
PDT 8137:Motorola G18 GSM/GPRS Radio Module, Type: G18
PDT 8142:Symbol Compact Flash RLAN (2Mbps DSSS) radio card, Type(s):
LA-302T
•
PDT 8146:Symbol Compact Flash RLAN (11Mbps DSSS) radio card, Type(s):
LA-412T
FCC RF Exposure Guidelines
Safety Information
The device complies with Internationally recognised standards covering Specific
Absorption Rate (SAR) related to human exposure to electromagnetic fields from
radio devices.
Reducing RF Influence - Use Properly
It is advisable to use the device only in the normal operating position and it is
recommended that no part of the human body be allowed to come too close to the
antenna during operation of the equipment.
Phones (placed to ear or used with headset)
To comply with RF safety requirements use the specific belt clip. All other belt clips
should be avoided and may not comply with RF safety requirements. The FCC has
granted an Equipment Authorization for these model phones with all reported SAR
levels evaluated as in compliance with the FCC RF emission guidelines. SAR
information on these model phones is on file with the FCC and can be found under
Handheld Devices
This device was tested for typical body-worn operation. The use of third-party belt-
clips, holsters, and similar accessories should not contain metallic components in its
assembly. The use of these accessories that do not satisfy these requirements may
not comply with FCC RF exposure compliance requirements, and should be avoided.
Laser Devices
Symbol devices using lasers comply with US 21CFR1040.10, and IEC825-1:1993,
EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels
on the device.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Scanner Labeling
39
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Laser Labels
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided
to the user:
ENGLISH
CLASS 1
CLASS 2
HEBREW
CLASS 1 LASER PRODUCT
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
DANISH / DANSK
ITALIAN / ITALIANO
KLASSE 1
KLASSE 2
KLASSE 1 LASERPRODUKT
LASERLYF
CLASSE 1
CLASSE 2
PRODOTTO AL LASER DI CLASSE 1
LUCE LASER
SE IKKE IND I STRÅLEN
KLASSE 2 LASERPRODUKT
NON FISSARE IL RAGGIOPRODOTTO
AL LASER DI CLASSE 2
DUTCH / NEDERLANDS
NORWEGIAN / NORSK
KLASSE 1
KLASSE 2
KLASSE-1 LASERPRODUKT
LASERLICHT
NIET IN STRAAL STAREN
KLASSE-2 LASERPRODUKT
KLASSE 1
KLASSE 2
LASERPRODUKT, KLASSE 1
LASERLYS IKKE STIRR INN I LYSSTRÅLEN
LASERPRODUKT, KLASSE 2
FINNISH / SUOMI
PORTUGUESE / PORTUGUÊS
LUOKKA 1
LUOKKA 2
LUOKKA 1 LASERTUOTE
LASERVALO
ÄLÄ TUIJOTA SÄDETTÄ
LUOKKA 2 LASERTUOTE
CLASSE 1
CLASSE 2
PRODUTO LASER DA CLASSE 1
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO
PRODUTO LASER DA CLASSE 2
FRENCH / FRANÇAIS
SPANISH / ESPAÑOL
CLASSE 1
CLASSE 2
PRODUIT LASER DE CLASSE 1
LUMIERE LASER
CLASE 1
CLASE 2
PRODUCTO LASER DE LA CLASE 1
LUZ LASER
NE PAS REGARDER LE RAYON FIXEMENT
PRODUIT LASER DE CLASSE 2
NO MIRE FIJAMENTE EL HAZ
PRODUCTO LASER DE LA CLASE 2
GERMAN / DEUTCH
SWEDISH / SVENSKA
KLASSE 1
KLASSE 2
LASERPRODUKT DER KLASSE 1
LASERSTRAHLEN
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN
LASERPRODUKT DER KLASSE 2
KLASS 1
KLASS 2
LASERPRODUKT KLASS 1
LASERLJUS STIRRA INTE MOT STRÅLEN
LASERPRODUKT KLASS 2
Power Supply
Note:Use only a Symbol-approved power supply 50-14000-107 output rated 9Vdc
and minimum 2A. The power supply is certified to EN60950 with SELV outputs.
Hinweis:Benutzen Sie nur eine Symbol Technologies genehmigt Stromversorgung
50-14000-107 in den Ausgabe: 9Vdc und minimum 2A. Die Stromversorgung ist
bescheinigt nach EN60950 mit SELV Ausgaben.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Cell Phone/Terminal Warnings
Safety on the Road
When driving a car, driving is your first responsibility. Check the laws and regulations
on the use of wireless phones in the areas where you drive. Always obey them. When
using your wireless device / phone behind the wheel of a car, practice good common
sense and remember the following tips:
1. Give full attention to driving -- driving safely is your first responsibility;
2. Get to know your wireless device and any features such as speed dial and re-
dial. If available, these features help you to place your call without taking your
attention off the road.
3. When available, use a hands free device.
4. Let the person you are speaking with know you are driving; if necessary, sus-
pend the call in heavy traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
5. Dial sensibly and assess the traffic; if possible, place calls when you are not
moving or before pulling into traffic. Try to plan calls when your car will be sta-
tionary. If you need to make a call while moving, dial only a few numbers,
check the road and your mirrors, then continue.
6. Do not engage in stressful or emotional conversations that may be distracting.
Make people you are talking with aware you are driving and suspend conver-
sations that have the potential to divert your attention from the road.
7. Use your wireless phone to call for help. Dial the Emergency services, (9-1-1
in the US, and 1-1-2 in Europe) or other local emergency number in the case
of fire, traffic accident or medical emergencies. Remember, it is a free call on
your wireless phone! The call can be made regardless of any security codes
and depending on a network, with or without a SIM card inserted.
8. Use your wireless phone to help others in emergencies. If you see an auto ac-
cident, crime in progress or other serious emergency where lives are in dan-
ger, call the Emergency Services, (9-1-1 in the US, and 1-1-2 in Europe) or
other local emergency number, as you would want others to do for you.
9. Call roadside assistance or a special non-emergency wireless assistance
number when necessary. If you see a broken-down vehicle posing no serious
hazard, a broken traffic signal, a minor traffic accident where no one appears
injured, or a vehicle you know to be stolen, call roadside assistance or other
special non-emergency wireless number.
10. Connection to an alert device that will cause a vehicle horn to sound or lights
to flash, on receipt of a call on public roads, is not permitted.
"The wireless industry reminds you to use your device / phone safely
when driving".
Effect on Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the manufacturer
or its representative regarding your vehicle. You should also consult the manufacturer
of any equipment that has been added to your vehicle.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
1. An air bag inflates with great force. DO NOT place objects, including either in-
stalled or portable wireless equipment, in the area over the air bag or in the air
bag deployment area. If in-vehicle wireless equipment is improperly installed
and the air bag inflates, serious injury could result.
2. Position your device within easy reach. Be able to access your device without
removing your eyes from the road.
3. Do not take notes or use the device while driving. Jotting down a "to do" list or
flipping through your address book takes attention away from your primary re-
sponsibility, driving safely.
Safety on Aircraft
You are required to switch OFF mobile phones when on board an aircraft as operation
may be dangerous and illegal.
Pacemakers
It is recommended by pacemaker manufacturers that a minimum of 15cm (6 inches)
be maintained between a handheld wireless phone and a pacemaker to avoid any
possible interference with the pacemaker. These recommendations are consistent
with independent research and recommendations by Wireless Technology Research.
Persons with Pacemakers:
•
Should ALWAYS keep the device more than 15cm (6 inches) from their pace-
maker when turned ON.
•
•
Should not carry the device in a breast pocket.
Should use the ear furthest from the pacemaker to minimise the potential for
interference.
•
If you have any reason to suspect that interference is taking place, turn OFF
your device.
Hearing Aids
The device may interfere with some hearing aids. In the event of interference you may
want to consult your hearing aid supplier to discuss solutions.
Other Medical Devices
The device transmits radio frequency energy and has the potential to interfere with
inadequately protected medical devices. Consult your physician or the manufacturer
of the device to see if the particular device has sufficient protection.
It is good practice to turn OFF the device within a hospital or other medical facility
where sensitive medical equipment is in use. In some countries, this is a legal
requirement applying to all mobile phones and related equipment.
Warning Notices
Please observe all warning notices with regard to the usage of mobile phones.
Potentially Hazardous Atmospheres
You are advised not to use this device at a refuelling point. You are reminded of the
need to observe restrictions on the use of radio devices in fuel depots, chemical
plants etc. and areas where the air contains chemicals or particles (such as grain,
dust, or metal powders) and any other area where you would normally be advised to
turn off your vehicle engine.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Hearing Aid Compatibility
This device is marked HAC showing compliance with the applicable requirements of
FCC Part 68 and CS03-Part 5.
Radio Frequency Interference Requirements-FCC
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
Tested to comply
with FCC Standards
FCC rules. These limits are designed to provide reasonable
FOR HOME OR OFFICE USE
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio Transmitters
This device complies with RSS 210 of Industry & Science Canada. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Label Marking: The Term "IC:" before the radio certification only signifies that Industry
Canada technical specifications were met.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
P
t
0
D
h
3
T
8
1
0
0
S
e
M
e
r
i
e
s
w
2
i
0
W
f
i
o
n
r
d
o
w
s
o
t
b
i
l
e
s
P
o
c
k
P
C
Marking and European Economic Area (EEA)
The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions:
•
Maximum radiated transmit power of 100 mW EIRP in the frequency range
2.400 -2.4835 GHz
•
•
France, equipment is restricted to 2.4465 -2.4835 GHz frequency range
Belgium outside usage, the equipment is restricted to 2.460 -2.4835 GHz fre-
quency range
•
Italy requires a user license for outside usage.
Statement of Compliance
Symbol Technologies, Inc., hereby, declares that this device is in compliance with the
essential requirements and other relevant provisions of Directives 1999/5/EC, 89/
336/EEC and 73/23/EEC. Declaration of Conformities may be obtained from http://
www2.symbol.com/doc/.
Other Countries
Mexico - Restrict Frequency Range to: 2.450 - 2.4835 GHz.
Israel
- Restrict Frequency Range to: 2.418 - 2.457 GHz.
Sri Lanka- Restrict Frequency Range to: 2.400 - 2.430 GHz.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Q
u
i
c
k
R
e
f
e
r
e
n
c
e
Warranty
(A) Warranty Symbol Technologies (hereafter “Seller”) hardware Products are warranted against defects in
workmanship and materials for a period of twelve (12) months from the date of shipment, unless otherwise
provided by Seller in writing, provided the Product remains unmodified and is operated under normal and
proper conditions. Warranty provisions and durations on software, integrated installed systems, Product
modified or designed to meet specific customer specifications (“Custom Products”), remanufactured
products, and reconditioned or upgraded products, shall be as provided in the applicable Product
specification in effect at the time of purchase or in the accompanying software license.
(B) Spare Parts Spare parts (i.e. parts, components, or subassemblies sold by Seller for use in the service
and maintenance of Products) are warranted against defects in workmanship and materials for a period of
thirty (30) days from the date of shipment. Spare parts may be new or originate from returned units under the
conditions set forth in subsection D below.
(C) Repair of Symbol-branded hardware For repairs on Symbol-branded hardware Products under this
Agreement, including repairs covered by warranty, the repair services provided are warranted against
defects in workmanship and materials on the repaired component of the Product for a period of thirty (30)
days from the shipment date of the repaired Product, or until the end of the original warranty period,
whichever is longer.
(D) Product Service Products may be serviced or manufactured with parts, components, or subassemblies
that originate from returned products and that have been tested as meeting applicable specifications for
equivalent new material and Products. The sole obligation of Seller for defective hardware Products is limited
to repair or replacement (at Seller’s option) on a “return to service depot” basis with prior Seller authorization.
Customer is responsible for shipment to the Seller and assumes all costs and risks associated with this
transportation; return shipment to the Customer will be at Seller's expense. Customer shall be responsible
for return shipment charges for product returned where Seller determines there is no defect (“No Defect
Found”), or for product returned that Seller determines is not eligible for warranty repair. No charge will be
made to Buyer for replacement parts for warranty repairs. Seller is not responsible for any damage to or loss
of any software programs, data or removable data storage media, or the restoration or reinstallation of any
software programs or data other than the software, if any, installed by Seller during manufacture of the
Product.
(E) Original Warranty Period Except for the warranty applying solely to the repaired component arising from
a repair service as provided in Section C above, the aforementioned provisions do not extend the original
warranty period of any Product that had either been repaired or replaced by Seller.
(F) Warranty Provisions The above warranty provisions shall not apply to any Product (i) which has been
repaired, tampered with, altered or modified, except by Seller’s authorized service personnel; (ii) in which the
defects or damage to the Product result from normal wear and tear, misuse, negligence, improper storage,
water or other liquids, battery leakage, use of parts or accessories not approved or supplied by Symbol, or
failure to perform operator handling and scheduled maintenance instructions supplied by Seller; (iii) which
has been subjected to unusual physical or electrical stress, abuse, or accident, or forces or exposure beyond
normal use within the specified operational and environmental parameters set forth in the applicable Product
specification; nor shall the above warranty provisions apply to any expendable or consumable items, such
as batteries, supplied with the Product.
EXCEPT FOR THE WARRANTY OF TITLE AND THE EXPRESS WARRANTIES STATED ABOVE,
SELLER DISCLAIMS ALL WARRANTIES ON PRODUCTS FURNISHED HEREUNDER INCLUDING ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE. ANY
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED
WARRANTY PERIOD. SOME STATES OR COUNTRIES DO NOT ALLOW A LIMITATION ON HOW LONG
AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS. IN SUCH STATES OR COUNTRIES, FOR
SUCH PRODUCTS, SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT
APPLY.
The stated express warranties are in lieu of all obligations or liabilities on the part of Seller for damages,
including but not limited to, special, indirect or consequential damages arising out of or in connection with
the use or performance of the Product or service. Seller’s liability for damages to Buyer or others resulting
from the use of any Product or service furnished hereunder shall in no way exceed the purchase price of said
Product or the fair market value of said service, except in instances of injury to persons or property.
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and
run your applications.
If you have a problem running your unit or using your equipment, contact your facility’s
Technical or Systems Support. If there is a problem with the equipment, they will
contact the Symbol Support Center:
United States
1-800-653-5350
1-631-738-2400
Canada
905-629-7226
United Kingdom
Australia
0800 328 2424
1-800-672-906
7020-1718
Asia/Pacific
+65-6796-9600
1-505-5794-0
9 5407 580
Austria/Österreich
Finland/Suomi
Denmark/Danmark
France
01-40-96-52-21
2-484441
Germany/Deutchland 6074-49020
Italy/Italia
Mexico/México
5-520-1835
Netherlands/Nederland 315-271700
Norway/Norge
+47 2232 4375
South Africa
11-8095311
Spain/España 91 324 40 00
Inside Spain
Sweden/Sverige
84452900
+34 91 324 40 00
Outside Spain
Latin America
Sales Support
1-800-347-0178 Inside US
+1-954-255-2610 Outside US
Europe/Mid-East
Distributor Operations
Contact local distributor or call
+44 118 945 7360
72-65988-01
Revision A — December 2003
Symbol Technologies, Inc. One Symbol Plaza, Holtsville, N.Y. 11742-1300
Download from Www.Somanuals.com. All Manuals Search And Download.
|