Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
15. To prevent electric shock, do not use this polarized
plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade
exposure.
This apparatus does not exceed the Class A/Class B
(whichever is applicable) limits for radio noise emissions
from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.
Pour préevenir les chocs électriques ne pas utiliser cette
fiche polariseé avec un prolongateur, un prise de courant
ou une autre sortie de courant, sauf si les lames peuvent
être insérées à fond sans laisser aucune pariie à
découvert.
ATTENTION — Le présent appareil numérique n'émet pas
de bruits radioélectriques dépassant las limites
applicables aux appareils numériques de class A/de class
B (selon le cas) prescrites dans le règlement sur le
brouillage radioélectrique édicté par les ministere des
communications du Canada.
16. Grounding or Polarization — Precautions should be
taken so that the grounding or polarization means of the
Component is not defeated.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
WARNING: ALWAYS FULLY INSERT THE PLUG
INTO THE AC SUPPLY SOCKET.
Contents
Safety instructions ..................................................................................... 2-3
Introduction .................................................................................................. 4
Features ....................................................................................................... 4
Unpacking .................................................................................................... 4
Overview ...................................................................................................... 5
Front panel features .................................................................................. 6-7
Rear panel features................................................................................... 8-9
Installation, AC power and connections ..................................................... 10
Care............................................................................................................ 10
The Phono stage................................................................................... 11-12
System Configurations ............................................................................... 13
Phono connections ................................................................................ 13
CD player connections........................................................................... 14
Tape deck connections.......................................................................... 15
Amplifier connections: unbalanced ........................................................ 16
Amplifier connections: balanced ............................................................ 17
Specifications ............................................................................................. 18
Troubleshooting guide........................................................................... 19-21
Appendix .................................................................................................... 22
Changing the phono stage gain............................................................. 22
Changing the phono stage input impedance ......................................... 22
Tube type and location .......................................................................... 22
Limited Warranty ........................................................................................ 23
Service assistance ..................................................................................... 23
To find out more about this and other Sunfire products,
Safety Instructions and Table of Contents
3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Introduction
Dear Friend,
Congratulations on your purchase of the Sunfire
Classic Preamplifier. We believe its sophisticated
engineering and meticulous craftsmanship will
provide you with many years of listening enjoyment.
At the heart of the Classic is a high-perfor-
mance control preamplifier with extremely low noise
and distortion, wide dynamic range, and a high
degree of control flexibility. An optional phono board
may be added for precise RIAA phono equalization
of moving magnet and moving coil cartridges. Your
Classic will provide remarkable three-dimensional
realism, with a sumptuous sonic image which can
extend beyond the loudspeakers in both breadth
and depth.
Bob Carver, Amplifier Designer, Physicist
Unpacking
Your Classic preamplifier should reach
you in perfect condition. If you do notice any
shipping damage, please contact your Sunfire
Dealer immediately.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
High quality vacuum tube design
6 L/R pairs of unbalanced inputs
Optional MM and MC Phono section
2 pairs of unbalanced main outputs
1 pair of balanced outputs
1 pair of tape outputs
Gently remove the Classic preamplifier
from its packing materials with care, so as to
avoid damage to or loss of any packing
materials. This is a precision instrument and
deserves to be treated with care. It has been
designed to provide years of reliable service,
and should you ever need to ship or transport
it, the original packing materials will provide
the safest means.
Low frequency contour control
High frequency contour control
Tape monitor switch
Make sure that you keep your sales
receipt. It is the only way to establish the
duration of your Limited Warranty and it may
come in useful for insurance purposes.
Stereo/mono switch
Motorized volume control
Balance control
Please take a moment to fill out and mail
the Sunfire Warranty Registration card. Also
read the serial number located on the rear
panel and record it here:
Remote control of volume, mute and
power
•
•
•
3 unswitched AC outlets
Gold-plated inputs and outputs
Classic chassis and styling
Serial Number:
Purchased from:
Date:
4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Overview
The Classic is a preamplifier control
center. If you have previous experience with
stereo components, you can probably com-
plete the input/output connections and make
normal use of the basic preamplifier functions
without special instructions. We recommend,
however, that you read the entire manual at
your earliest convenience. You will find that
even some of the “conventional” parts of the
Classic are in fact not conventional at all.
Note: The remote control
will only work when the
front panel power switch
is in the ON position.
Mute
Power
on/off
Gain
control
Power
on/off
Mono/
Stereo
Tape
Tone
Input
Contour (tone) Balance
controls
Monitor on/off selector
PHONO/LINE INPUTS
INVERSE
U
N
S
W
I
PHONO
PHONO
OUTPUTS
LINE INPUTS
VIDEO
MOVING
COIL
MOVING
MAGNET
PHONO
OUT
LINE
IN
1000
WATTS
TOTAL
USE EITHER
T
MAIN 1
MAIN 2
TAPE
TAPE
AUX
CD
TUNER
C
H
E
D
L
L
L
BALANCED
REPLACE WITH
ORIGINAL TYPE
AND RATING
ONLY
R
R
R
2 AMP
AGC
PASSIVE PRECISION
INVERSE RIAA PHONO NETWORK
120 VAC
50/60 Hz
S/N
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
AC
AC Fuse XLR
outs
Tape Tape
Line
inputs
Main
outs
MM/MC
switch
Optional
Phono
section
outlets cord
out
in
Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Front Panel Features
4
1 2 3 5
6
7
8
11
10
9
1. Power Switch
4. Remote window
This is the main AC power switch. Flip the switch up to
apply power to the unit. It is good practice to turn the
volume control down before turning on, and keep it
down until after about 40 seconds of tube warm-up
time (when the MUTE lamp turns off, and the ON
lamp stops blinking and turns on continuously).
This window should be kept clear of obstruction for
the remote control to work.
5. Stereo/Mono Switch
This sums the left and right inputs so the main outputs
will have identical signals. (It does not affect the Tape
outputs).
If you prefer, you may leave this AC power switch
permanently on, and use the remote control to switch
the unit on or off. Turning the power off with the
remote will extinguish both the MUTE and ON lamps.
The most common use for this switch is in checking
loudspeaker phasing: Play any stereo or mono
recording, select Mono and listen. Then reverse the
polarity (+, -) of one speaker connection and recheck.
The polarity position which develops a clear center
image between the speakers with fullest bass content
is the correct “in-phase” position of the speaker wiring.
Note: the power switch must be in the up (POWER)
position for the remote control to work.
2. On lamp
During normal operation this lamp will be on. When
you turn the preamplifier on, this lamp blinks for about
40 seconds while the tubes are warming up. After that
time, it will stay on continuously.
You should also engage Mono for playback of old
monophonic sources, since this will cancel most
rumble and noise for quieter playback.
When listening to a single-channel source, you can
either use a “Y” cord at the selected input, or select
Mono.
3. Mute lamp
During normal operation, this lamp will be off. When
you turn the preamplifier on, this lamp stays on for
about 40 seconds while the tubes are warming up,
indicating that the outputs are muted and no sound is
passed to your amplifiers. The lamp will also indicate
whenever the remote control MUTE is pressed.
6. Tape Monitor switch
This will connect the output of a recorder to the
subsequent preamplifier circuitry. It may be used for
tape playback or record-monitoring with three-head
recorders. Similarly, if a signal processor is connected
to the preamplifier’s Tape inputs and outputs, it will be
in circuit whenever the Tape Monitor switch is en-
gaged.
If you accidentally turn off the preamplifier using the
remote, you can quickly turn it back on. The preampli-
fier will automatically sense that there is no need for a
40 second mute because the tubes are already
warmed up.
6
Front Panel Features
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
7. Contour On/Off
10. Balance Control
In the OFF position, the contour circuits are bypassed
and the two contour controls (11) will have no effect.
This adjusts the relative levels of the two stereo
channels. In its center position, the levels are exactly
equal. Clockwise rotation reduces the Left channel
level, while counterclockwise rotation reduces Right
channel level. Small movements off-center produce
smaller shifts in the stereo image per degree of
rotation than near the extreme left and right position.
This makes slight trimming of levels more convenient.
In the ON position, the signal frequency response can
be adjusted by the contour controls to suit your taste.
8. Input Program Selector
This rotary switch selects the program source which
will be heard. The same program source is also
presented to the Tape outputs for recording. Note that
there is no Tape selection, you should engage the
Tape Monitor switch to listen to your tape deck.
11. Contour Controls
The Sunfire Classic is equipped with a tone-control
stage in the signal path after all input selection and
tape switching. These controls are switches which
select a variety of precise contour curves. In opera-
tion, a muted click or pop may be heard when chang-
ing switch positions. The controls may be switched in
or out of circuit by the contour switch (7), allowing the
contoured signal to be quickly compared with the
preamplifier’s laboratory-flat frequency response.
If you have the optional Phono input, select either MM
or MC using the rear panel switch (depending upon
your phono cartridge), and then select CD/Phono.
To minimize bleedthrough, or an audible signal when
you select an unused input, it is recommended that
“shorting plugs” be inserted in all unused inputs. Do
Not install shorting plugs in any OUTPUT jacks, as
this would short-circuit the preamplifier output. If you
do not use shorting plugs, that is perfectly OK., and
you can prevent bleedthrough by turning off or muting
all signal sources not being listened to.
The contour controls are asymmetrical in boost and
cut. They have been designed to be very appropriate
for real music listening situations. The boost exhibits
no shelving, and reaches a maximum of +6 dB at full
clockwise rotation. Bass may thus be boosted without
the boom associated with shelving, in order to in-
crease deep punch without mid-bass fatness. Treble
boost will field greater definition, without the shrillness
which results from treble-boost shelving.
9. Volume Control
This is the master level control for the stereo system.
The control is a continuous taper potentiometer to
allow smooth transition from one level to another.
In the cut (counterclockwise) position, treble and bass
are not rolled-off, as with most tone controls, rather
energy output in the upper and lower ranges is
reduced while maintaining flat frequency response in
those ranges. Cut does not exceed -10 dB, since
frequency response attenuation beyond this yields a
dead sound character which is not musically advanta-
geous. Cut is not substantially affected by the tone-
turnover frequency switches. This shelving character-
istic for the cut mode is very useful, for example, if a
recording sounds too bright. The relative harmonic
energy can be reduced without affecting the balance
of the harmonic content. Thus, a violin will still sound
like a violin, retaining its air, sheen and openness,
while reducing excessive brightness.
The taper rate of the potentiometer was chosen to
provide maximum flexibility and compatibility with
other components. Input signal levels will vary from
one source to the next, as well as from one disc, tape,
or FM station to the next, so it is normal to notice that
your preferred volume control setting varies.
Note: The remote control’s Volume Up function is
disabled when the system is muted or warming up.
This is to prevent causing damage to your speakers
due to accidentally high volume levels. The remote’s
Volume Down function is available at all times, and
you can still set the volume at any time using the front
panel control (but make sure it is turned down while
the preamp is warming up).
Note: We encourage the routine use of the contour
controls as this will significantly enhance your listening
pleasure.
Front Panel Features
7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Rear Panel Features
4
5
6
7
8
9 10 11 12 13 14
PHONO/LINE INPUTS
INVERSE
U
N
S
W
I
PHONO
PHONO
3
OUTPUTS
LINE INPUTS
VIDEO
MOVING
COIL
MOVING
MAGNET
PHONO
OUT
LINE
IN
1000
WATTS
TOTAL
USE EITHER
MAIN MAIN
T
1
2
TAPE
TAPE
AUX
CD
TUNER
C
H
E
D
L
L
L
15
16
BALANCED
REPLACE WITH
ORIGINAL TYPE
AND RATING
ONLY
R
R
R
2 AMP
AGC
2
1
PASSIVE PRECISION
INVERSE RIAA PHONO NETWORK
120 VAC
50/60 Hz
S/N
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
1. AC Line Cord
If your power amp is not equipped with a
power switch, make sure that the
preamplifier’s power switch is OFF
(indicator LED is not lit) and its AC line-
cord is unplugged, before connecting the
power amp’s line cord to one of the
Classic’s outlets.
This is heavy-duty cord capable of
carrying large currents required by high-
power amplifiers. The Classic itself
requires only modest power (equivalent to
most light bulbs) and may thus be pow-
ered by a conventional extension cord if
required. But if you have substantial
power amplifiers connected to one of the
convenience outlets, only use a heavy
duty extension cord (16 gauge or thicker).
4. Balanced outputs
These are the left and right outputs which
connect to the balanced inputs of an
amplifier used to drive your speakers.
The line cord should only be plugged in
after completing all input and output
connections to other components.
Balanced outputs offer superior noise
cancellation, especially if there is a long
cable run to your amplifier.
2. Fuse
Always unplug the power cord
before inspecting or changing the
fuse. Never use a fuse with a
larger current rating than 2 A.
5. Main 1 and Main 2 outputs
MAIN 1 - These are left and right unbal-
anced (RCA) outputs which connect to
the unbalanced inputs of an amplifier
used to drive your main front speakers.
3. Accessory outlets
These three unswitched AC outlets are
LIVE whenever the unit’s line cord is
plugged into an active AC receptacle.
They can be used to supply AC power to
other components of your system,
including your amplifier. The total power
draw must not exceed 1000W.
MAIN 2 - Identical to Main 1. They can be
used to drive a second power amplifier,
such as in bi-wire or multiple speaker
applications, to drive a subwoofer, or to
feed processed signals to a tape recorder
or a time-delay accessory.
Verify that all component power-switches
are OFF before plugging any component
line cords into these or any AC outlets.
8
Rear Panel Features
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
6. Tape output
12. Moving Coil phono input
These outputs connect to the inputs of a
tape deck for recording the source which
is currently selected by the preamplifier.
Connect to the output of a turntable
equipped with a moving coil phono
cartridge. Push the rear panel MM/MC
selector button IN.
Input jacks on your tape deck may be
labeled “Line In”, “Aux”, or “Record”, but
do not use “Microphone.”
13. Moving Magnet phono input
Connect to the output of a turntable
equipped with a moving magnet phono
cartridge. Push the rear panel MM/MC
selector button OUT.
It is recommended that DIN-type record/
play sockets not be used if conventional
RCA jacks are available at the recorder.
7. Tape input
14. Inverse-phono section
This connects to the outputs of a tape
deck for playing your favorite tapes
through the preamplifier. This input is
selected using the TAPE MONITOR
switch, not by the Input selector control.
The Classic preamplifier allows you to
play your CDs or other line level sources
through the phono stage. It can also be
used to check the phono stage operation.
The special wiring configuration and
details for this circuit are described and
illustrated on page 12.
Tape deck output jacks may be identified
as “Line Out”, “Play”, or “Monitor”.
8. Aux input
15. Ground
These line-level inputs are electrically
identical to the other line inputs, and may
be used for signal sources such as a
second tuner, a tape-deck, TV audio
tuner, VCR or the output of a microphone
preamplifier.
Attach your turntable’s ground wire to this
point to prevent hum.
16. MM/MC selector
Push this IN if you are using the Moving
Coil (MC) input. Push it OUT if you are
using the Moving Magnet (MM) input.
9. Video input
For connection of the audio output from a
VCR, DVD, satellite tuner or TV.
Note
An additional line level
PHONO/LINE INPUTS
input is available if the
optional Phono stage
has not been installed.
This input (or the phono
stage) is selected using
the input selector’s CD/
PHONO position.
10. CD input
INVERSE
PHONO
PHONO
MOVING
COIL
MOVING
MAGNET
PHONO
OUT
LINE
IN
For connection of the output from a CD
player. This input is selected using the
input selector’s COMPACT DISC position.
If your player has “fixed” and “variable”
outputs, use the variable outputs. Then
you can adjust the output level of the CD
player so that when you switch from
Phono to CD to Tuner, the volume level
will remain approximately the same.
TUNER
L
CD/LINE INPUT
Line level only
R
PASSIVE PRECISION
INVERSE RIAA PHONO NETWORK
For more details of the
Phono stage, see pages
11 and 12.
11. Tuner input
Connect to the line-level output from a FM
or AM/FM tuner.
Rear Panel Features
9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Installation
Observe the following precautions when
choosing a location for your Classic vacuum
tube preamplifier:
AC Power Considerations
Ensure that the unit is plugged into an outlet
capable of supplying the correct voltage
specified for your model.
•
•
•
The Classic is an all-vacuum tube
design. It may be operated at any
angle, and has modest ventilation
requirements. Do not cover the side
ventilation slots.
Care
If you need to clean the front surface, first turn
off the power and then use a slightly damp-
ened cloth, rubbing with the grain. Be careful
not to scratch the front window.
It’s location relative to other stereo
components is not critical, except that
it should not be stacked with, or placed
adjacent to, powerful amplifiers which
may generate external hum fields.
Connection Tips
Before setting up your new system, please
consider the following :
Typically it is best to locate the Classic
close to the turntable or CD player so
that connection cables may be kept
short. The turntable should be on a
solid, vibration-free surface to avoid
problems of acoustic feedback and
instability. In many systems it may be
convenient to locate the preamp within
arm’s length of the prime listening
position, for which long cables to the
amplifier will be necessary; normally,
cable runs of up to 30 feet are OK.
•
Before making or changing any
connections, check the front panel to
make sure the Power switch is DOWN
(off), and that the Volume Control is
set for no output (full counterclock-
wise). The amplifier and all other
equipment should be turned off and
the preamplifier line cord unplugged
before making any connections.
•
Whenever possible, keep the power
cords away from the signal cables
or speaker wires to prevent any hum
or interference being heard in the
speakers.
•
•
Protect it from prolonged exposure to
direct sunlight and other direct
sources of heat, such as heating
vents and radiators.
•
•
Choose reliable interconnect cables,
also called patch cords or RCA cables.
They should be fully shielded and as
short as possible for the job.
Do not expose the unit to rain or
moisture. If fluid or a foreign object
should enter the unit, immediately turn
off the power and contact your Sunfire
Dealer.
If your amplifier has balanced inputs,
then we recommend using the bal-
anced outputs of the preamplifier as
this will provide superior noise rejec-
tion.
•
•
Avoid excessive exposure to
extreme cold or dust.
Do not place heavy objects on top of
the unit.
•
Some patch cords can be a very tight
fit and there is usually a preferred
method of getting them off, some have
to be removed with a twisting action.
Be gentle or you may damage the
jacks of the amplifier or your other
components.
10
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
The Phono stage
Moving Magnet phono input
The rear panel MM/MC selector button
must be OUT for moving magnet cartridges.
PHONO/LINE INPUTS
The moving magnet phono circuit has a
total gain of 40dB, appropriate for typical high
output moving magnet and moving iron
cartridges.
INVERSE
PHONO
PHONO
MOVING
COIL
MOVING
MAGNET
PHONO
OUT
LINE
IN
TUNER
L
Its input impedance consists of 47K ohms
resistance in parallel with real capacitance.
This prevents the complex input interactions
which can cause small response shifts in
some systems. When plugging the cables into
the Classic’s sockets, be sure each plug is
inserted fully into the socket, making a tight fit.
R
PASSIVE PRECISION
INVERSE RIAA PHONO NETWORK
You can plug the turntable line cord into
one of the accessory outlets on the rear panel
of the Classic preamplifier.
MM/MC
switch
Ground
connection
Moving Coil phono input
The optional phono stage contains two
independent stereo phono preamplifier inputs
which are optimized for specific uses. The
type of phono cartridge you are using in the
turntable will determine which phono input to
use. Only a moving coil cartridge should be
connected to the moving coil input, or it may
become overloaded and distort.
The rear panel MM/MC selector button
must be IN for moving coil cartridges.
The two inputs marked MC are intended
for use with moving coil cartridges only. This
Phono circuit employs an additional 20dB of
linear gain (for a total of 60 dB to Tape
Outputs), designed especially for the relatively
low voltage output of moving coil cartridges.
The Classic employs a built-in “pre-amplifier”,
but this design is free of the compromises
usually associated with active gain at this
stage.
In terms of frequency response, the
moving coil and the moving magnet phono
are identical. In terms of gain and sensitivity,
however, they differ substantially.
Ground connection
Historically, the problem of obtaining the
extra gain required for the moving coil car-
tridge has been an expensive proposition. The
problem has been as follows: To obtain low
noise, a step-up transformer has been
required, transforming the low cartridge
impedance up to the 47K ohm input imped-
ance of the phono stage. In this process, the
noise floor of the system is generally estab-
lished by the 3 to 10 ohm source resistance
associated with the moving coil cartridge, and
is therefore very low. However, in order to
obtain signal performance comparable to
even simple active electronic circuits, heroic
If your turntable is equipped with a
separate ground lead (usually a single wire
terminated with a spade lug), connect it to the
ground post, (see item #15 on page 8). In
most cases, this will minimize audible hum
and buzz in the phono signal. If hum is a
problem with your turntable, refer to the
troubleshooting section starting on page 19.
Normally, these are the only connections
made to the ground post, while all other
components are grounded through their own
signal cables.
The Phono stage
11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
efforts on the part of the transformer designer
are required, and the resulting cost will almost
always be many hundreds of dollars. Less
expensive transformers will be quiet, but will
usually exhibit ringing, phase shift, and some
low frequency distortion. The problems with
most active step-up devices are simply
reversed. Moderate cost, smooth high-
frequency response, essentially zero phase
shift and low distortion may almost be taken
for granted, while heroic and expensive
design techniques, including cryogenic
cooling, have been required to even approach
the low noise of a transformer.
circumstances, have a just perceptible
consequence in the audio passband. Infra-
sonic filtering is thus often somewhat of a
compromise. In order to eliminate this prob-
lem, the onset of rolloff has been delayed a
full octave below 20 Hz, effectively reducing
group delay to well below the threshold of
audibility.
Precision Inverse RIAA Network
A wonderful and classic pleasure in this
day and age of digital audio is to listen to vinyl
records, which were made using the RIAA
equalization curve. Ordinarily of course, with
CDs that’s not possible. The next best thing,
however, is to use your Sunfire’s Precision
Inverse RIAA network to listen to CDs through
its classic vacuum tube phono stage:
A superbly accurate dual parallel input,
combined with the use of high current tubes
which exhibit an almost unheard-of noise
figure at room temperatures, made a new
“super-gain” phono stage possible. It yields all
the performance advantages of active circuits,
with noise levels within 6 dB of the best
transformers, all at moderate cost and at
room temperature.
•
Connect the output of your CD player
to the line-input of the inverse phono
network.
•
Connect the phono output of the
inverse phono network to the input of
the MM phono stage, using a short
interconnect cable.
To change the gain or the input imped-
ance of your phono stage please refer to the
Appendix on page 22.
•
•
Make sure that the MM/MC selector
button is OUT to select the MM input.
Infrasonic Filter
This circuit corrects for difficulties often
encountered with phono disc playback.
Set the front panel selector switch to
CD/Phono; and “Voila”, RIAA sound
from CDs!
The Infrasonic Filter is an 18 dB per
octave design. Its response is flat down to
10Hz, then attenuates the preamp’s frequency
response rapidly at lower frequencies. Phono
playback is inevitably contaminated to some
extent by sub-sonic energy, due to normal
amounts of record warp, tonearm/cartridge
resonance and turntable motor rumble. If not
filtered out of the audio signal, this sub-
audible energy can overload tape recorders,
waste amplifier power, and drive woofers into
excessive cone excursions, causing
•
This mode also allows a line source to
be used to check that the MM phono
stage is working correctly.
PHONO
/LINE INPUTS
P
H
IN
P
O
V
N
E
O
R
SE
H
M
ON
O
V
O
IN
G
IL
M
O
V
IN
E
G
T
C
O
P
H
O
O
N
O
M
A
G
N
L
IN
E
IN
U
T
L
R
intermodulation distortion audible as muddy
bass.
P
A
S
S
IV
E
P
IN
R
E
V
C
IS
E
R
IO
S
E
N
T
W
R
IA
A
P
H
O
N
O
N
E
O
R
K
Normally, “group delay”, an unavoidable
consequence of the rapid attenuation of sub-
sonic response, can, under certain musical
FROM CD PLAYER
12
The Phono stage
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
System Configurations
The following pages show some typical
connections that you might make in your installa-
tion. They show how the inputs and outputs of
the Classic preamplifier are connected to
various audio components.
If your turntable is equipped with a Moving
In most cases, the turntable ground wire
Magnet cartridge, connect its audio outputs to
the preamplifier’s Moving Magnet inputs as
shown. Make sure that the MM/MC button is
in the OUT position.
should be connected to reduce any hum
heard in the speakers.
Never connect a line-level source compo-
nent directly to the preamplifier’s MC or MM
inputs as they will be overloaded. They are
specially designed to handle only the very low
level outputs from a phono cartridge, and not
the higher voltage outputs from CD players or
other line level components. (Phono level is
usually below 100mV, whereas line level can
be up to 2 volts).
If you have a Moving Coil cartridge, use
the preamplifier’s Moving Coil inputs and push
the MM/MC button inwards.
Phono Connections
System Configurations
13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
CD player
The audio output from your CD player can
be connected to the preamplifier’s CD inputs.
Any of the line level inputs, such as
TUNER, CD, VIDEO, AUX and TAPE can be
used by any source component with a line
level output, such as DVD, LaserDisc, VCR,
reel-to-reel, DAT, TV or satellite receiver.
If your CD player has variable outputs,
this will allow you to adjust the CD player’s
output volume to match the volume of other
components in your system, such as the tape
deck or turntable. When you switch from one
component to the next, the initial volume
would then be similar.
If you want your CD player to have an
extra special sound, you can use the Inverse
RIAA circuits as shown on page 12.
CD player Connections
14
System Configurations
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Tape Deck
The output from your Tape deck connects
to the preamplifier’s TAPE inputs. These
inputs are only selected by using the
preamplifier’s Tape Monitor switch.
An external processor can be connected
in exactly the same way as a Tape deck:
•
The external processor outputs
connect to the preamplifier’s Tape
inputs.
The inputs of your Tape deck connect to
the preamplifier’s TAPE outputs. These
outputs are unaffected by the setting of the
volume control or the contour controls.
•
•
The external processor inputs connect
to the preamplifier’s Tape outputs.
Select the source you would like to
listen to, such as CD, and then select
the Tape Monitor switch to listen to the
processed sound.
Tape Deck Connections
System Configurations
15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Amplifier
If your amplifier has RCA inputs, you can
connect them to the preamplifier’s Main 1 or
Main 2 outputs. It does not matter which pair
you use, because they are identical.
If you are using an electronic crossover to
bi-amp or tri-amp your speakers:
•
Connect a cable from either of the
preamplifier’s main outputs to the
active crossover’s inputs
Main 2 is provided if you want to run a
second amplifier, perhaps to play speakers in
another room, or to drive an active subwoofer.
•
Connect the crossover’s High, Mid,
and Low outputs, as appropriate, to the
separate power amplifiers in your
system.
A third amplifier can be connected to the
balanced XLR outputs if you have another set
of speakers in a third room. Note that all the
amplifiers would be playing the same music
selection.
Amplifier Connections: unbalanced RCA
16
System Configurations
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Amplifier
If your amplifier has XLR inputs, it can be
connected to the balanced audio outputs as
shown.
The balanced connections are preferred,
as they provide superior noise cancellation
and are less susceptible to interference than
unbalanced lines.
Amplifier Connections: balanced XLR
System Configurations
17
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Specifications
Phono Inputs
Line Voltage
Units built for 110V-120V line voltage can
be converted to 220V-240V by means of a
modification. This is not simply a switch, and
must be performed by a Sunfire Authorized
Service Station. Contact Sunfire Technical
Services for more information.
RIAA curve
Moving Magnet input
Gain = 40dB to tape out
Overload = 100mV @ 1 kHz.
Input Impedance = 47Ω
Noise: better than 82 dB, IHF-A,
below 10mVrms at 1 kHz
Moving Coil input
Muting System
The Sunfire Classic employs an electronic
“clamper” to mute the main outputs to elimi-
nate turn-on transients. (It will not interrupt the
tape outputs).
Gain = 60dB to tape out
Overload = 5.60 mV @ 1 kHz.
Input Impedance = 470Ω standard,
(setable to 22Ω, 47Ω, 150Ω or 470Ω)
Noise: better than 76 dB, IHF-A,
below 1000 µVrms at 1 kHz
Muting is accomplished by a shorting
relay which, when it is “open”, is out of the
circuit and hence has no effect on the signal.
It is controlled by a toggling device, so muting
cannot be partially “on”.
High-Level Inputs
Frequency response
This muting system will turn off the signal
to your power amplifier at these times:
5 Hz to 50 kHz +0/-3dB
Line Gain = 12dB
Infrasonic Filter
18 dB per octave below 10 Hz
Noise
better than 96 dB, IHF-A, below 2 Vrms.
Distortion
THD: 0.5% or less, below 3 Vrms out.
IM (CCIR or SMPTE): 0.5% or less.
TIM unmeasurable.
•
For about 40 seconds after the initial
power-on, whether by the front panel
power switch or the remote control.
•
•
Immediately at turn-off, whether by the
power switch or the remote control.
The main outputs will also mute if the
line voltage drops below 70 volts. This
is to reduce thumping.
Input Impedance nominally 50kΩ
Power Consumption
Output impedance
45 Watts with Phono option
25 Watts without Phono option
1.4 Watts remote standby (i.e. when it
has been turned off using the
remote control)
The output impedance of the Classic is a
low 1.5K ohms, so it can drive power amplifi-
ers having virtually any input impedance.
Options include connecting several power
amplifiers to the Classic’s main outputs, to
separately drive different speaker sets, or the
use of extra-long connection cables to drive
power amplifier(s) located close to the speak-
ers, or self-powered loudspeakers. Conven-
tional cables as long as 30 feet, or special
low-capacitance cables as long as 60 feet,
may be used to drive power amplifier(s)
without difficulty.
Finish
Black anodized front panel and cover
Dimensions
19” wide x 6.5” high x 18” deep.
Weight
©2001 Sunfire Corporation. All rights
reserved. Sunfire Corporation reserves the
right to improve its products at any time.
Therefore, specifications are subject to
change without notice.
25 pounds
Manual Part number : 913-012-00 Rev C
18
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Troubleshooting
No sound.
In view of the Classic’s input/output
flexibility, the many connecting cables to and
from the components which may be con-
nected to it, and the large number of possibili-
ties for mis-set switches both on the Classic
and on the various ancillary components
operating with it, obviously it is impossible to
offer a complete troubleshooting guide to all
of the problems which could, in principle,
occur. Most such potential problems will be
avoided simply by following the instructions in
this owner’s manual and the instructions
supplied with associated products; and many
other possible problems will be prevented
simply by the excellent reliability of modern
components.
•
The preamplifier’s power may be off,
the amplifier off, line cords unplugged,
AC fuses blown, or the power may be
off at the wall socket or power strip.
No sound (the power is on)
•
Input selector set to an inactive input.
•
Tape monitor switch is engaged with
no tape machine running.
•
•
•
•
•
Input level controls are turned down on
the power amplifier.
Input or output signal cables may be
disconnected.
The selected program source is not
operating.
So in this section we will provide a guide
to some of the most basic and common
difficulties which may arise from time to time,
and suggestions as to their probable causes.
To illustrate the sort of thought process which
is useful in tracking down problems, we begin
with the most basic: no sound because the
preamp’s power is off. Did you accidentally hit
the Power button when reaching for the
Stereo/Mono button? Was the preamp’s AC
line cord accidentally pulled partially out of its
wall socket during housecleaning earlier in the
day? Did something else on that same
household branch circuit (including the power
amp or other component plugged in the
preamp’s AC convenience outlets) cause a
current surge which blew the fuse or circuit
breaker protecting that entire branch circuit?
In some houses having duplex AC wall
sockets, the lower one is permanently live
while the upper one (intended for lamps) is
controlled by a wall switch near a doorway;
was the preamp’s AC cord accidentally
plugged into the switched socket? Is the
preamp’s AC cord plugged into a clock timer
which is presently off or unplugged from the
wall?
Output level control turned down at
program source.
Program source misadjusted (for
example, the FM tuner is tuned
between stations.
No sound (phono)
•
Rear panel Phono MM/MC selector
button in wrong position.
•
•
Internal ribbon cable unplugged
No phono power jumper in place on
power supply board.
No sound in one channel.
•
Defective cable from the preamp to the
power amp or from a program source
to the preamp.
•
•
Speaker wire loose or disconnected.
Balance control fully clockwise or
counter-clockwise.
•
Imperfect contact in a switch (espe-
cially any lever or slide switch in a
program source or signal processor,
as well as the various signal-routing
switches in the preamp).
•
A speaker’s fuse is blown.
Troubleshooting
19
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Turntables and tape decks are sensitive
to the external hum fields created by many
power amplifiers, and sometimes to the hum
fields of other house appliances (such as a
refrigerator on the other side of the wall). It is
important that signal cables in general, and
the turntable signal leads in particular, should
not run close to and parallel with AC power
cords, nor close to a power transformer or
motor (including that in the base of the
turntable).
Loud howl, squeal, or whistle.
•
The Tape Monitor switch is engaged
while microphones (in the same room
as the speakers) are connected to a
tape deck for recording.
•
Put the cat out.
Solo voices, or instruments
sound thin, shrill or distorted.
•
Phono cartridge is wired out of phase.
As a test, you might try and disconnect all
cables which come from outside the room,
such as cable TV, satellite TV, or roof top
antennas. Make sure that they are discon-
nected where they first enter the room, so
they are making no connection to your VCR,
TV, or any other component. If you find that
noise goes away when a cable TV line is
disconnected, then you will need a “ground-
loop isolator.” This is an inexpensive device
fitted in line with the coaxial cable feed.
Hum
Under normal operating conditions you
hear very little hum originating in the circuitry
of the Classic. There is one exception to this
rule: If you have a high-gain power amplifier
and unusually sensitive (i.e. efficient) loud-
speakers, normal listening levels will involve
using abnormally low output levels from the
preamp, and those small signals might then
pick a bit of hum or hiss in the preamp’s
circuits. In this case the solution is to turn
down the power amplifier’s level controls if it
has them, or consider having its gain reduced
by the manufacturer. Contact Sunfire Techni-
cal Services for further information.
If the hum persists, disconnect all the
source components one at a time from the
back of the preamplifier and you may identify
the problem.
In many cases, hum may be eliminated by
reversing the Classic’s (unpolarized) AC
power plug in the wall socket. In others it can
be minimized by connecting a heavy stranded
wire from the preamplifier’s ground post to a
true earth ground — which may turn out to be
any, all, or none of the following: the third
(round) hole in an electrical wall socket in
modern U.S. homes, a steam radiator, or a
cold water pipe. However, if your power
amplifier employs a three-wire power cord,
the stereo system may already be grounded
through that, in which case another grounded
wire from the preamp may create a “ground
loop” and make the hum worse. As for the
various components within the stereo system,
they are mutually grounded via the shields of
the signal cables and should not be intercon-
nected with additional grounding wires, for the
same reason (except, of course, the turntable;
whose grounding wire usually (but not always)
should be connected to the preamplifier’s
ground post).
Except for the condition described above,
audible hum will nearly always be found to be
due to problems external to the Classic —
usually in the signal source, i.e. the turntable
or tape deck. Many turntables, for example,
have a hum field in the vicinity of the platter
due to the turntable’s motor or internal power
transformer which is acceptably low with
moving-magnet cartridges but audibly bother-
some with moving-coil cartridges. If your
turntable has a non-polarized AC plug, you
can experiment with reversing it to see which
orientation of the plug minimizes the audible
hum. The hum may also vary with the location
and orientation of the turntable with respect to
AC wiring in the walls, making it necessary to
move the turntable to another part of the
room.
20
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Finally we come to the other common
source of hum problems, the signal cables
and their associated plugs. Inexpensive
cables often have mediocre wrapped shield-
ing, so better cables may make an audible
difference. And it is important that the plug at
each end of every cable makes a good, tight
fit in its mating socket. (In this, don’t neglect
the “source” end of the turntable signal
cables, which in many tables are plugged into
sockets underneath rather than being sol-
dered to terminals within the turntable’s base).
Crimp the leaves of the phono plug’s skirt
slightly inward, if necessary, to ensure that it
has a tight friction-fit on the exterior of the
phono jack. When plugging in each cable, use
a rotary twisting motion as the plug goes into
the jack, in order to scrape away any invisible
surface corrosion and make a clean metal-to-
metal contact. Finally, in many inexpensive
molded cables, the wire breaks where it
makes contact with the plug; this problem can
be identified by wiggling the cable and listen-
ing for an intermittent signal connection or
intermittent hum.
If the interference disappears when you
mute the output of the preamp, then the
interference is part of the signal and probably
is entering the preamp from one or more of
your signal sources. Use the Input Selector
and Tape Monitor controls to identify which
signal sources are picking up the interference,
or unplug the sources one at a time. Usually
turntables and tape decks are most vulner-
able to RFI. If the RFI is coming in through the
phono signal leads, cables with better shield-
ing might help. Other options include wrap-
ping the signal cables with aluminum foil
which is then connected to the Ground post;
or forming a loop in the cables, adjusting the
size of the loop to tune out the interference,
and taping it in place. And as with hum, try
tightening all phono plugs and twist them in
their sockets to get good metal-to-metal
contact.
RFI in tape decks may enter via signal
cables, but more commonly the interference
is picked up directly in the playback head and
its associated internal wiring, so a cure is
likely to involve a trip to the factory or service
shop for approved modifications. Or you might
be able to reduce the interference to tolerable
levels simply by turning the tape deck 90
degrees or moving it to another location in the
room. A signal-processor, such as an equal-
izer, may be connected between either Main
output set and the inputs of the power ampli-
fier which drives the speakers you wish to
equalize.
Radio Frequency Interference
Radio Frequency interference (RFI) from
CB, TV, AM, and other radio transmitters is a
common problem, and like hum it usually can
be traced to a condition external to the
Classic. Sometimes RFI gets into the power
amp via the signal cables running from the
preamp, and may be cured by substituting
cables with better braided or foil shielding.
More commonly RFI enters the power amp
through its output terminals, with the speaker
wires acting as receiving antennas. In this
case it might be cured by connecting a 0.01 to
0.1 microfarad disc capacitor across the
speaker terminals of each channel, but be
sure to check with the amplifier manufacturer
first; some power amps become unstable and
burn out when certain values of capacitance
are connected at their output terminals. A
simple cure is to place the power amp near
the speakers and use short wires; then use
long well-shielded signal cables from the
preamp to the power amp. This shouldn’t
cause any problems under normal conditions.
Troubleshooting
21
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Appendix
Changing the phono stage gain
Tube type and location
Phono Board
The following gain changes may be
performed by experienced electronic techni-
cians. Your Sunfire Dealer may be able to
recommend a good service/repair shop.
V1 6DJ8 or 6922 MC amp
V2 6DJ8 or 6922 MC amp
V3 6DJ8 or 6922 MC amp
Factory set gain of MM Phono is 40 dB.
The gain may be changed as follows:
V4 12AX7
V5 12AX7
MM amp
MM amp
36 dB - change R 11 and R 35 to 3.9 K ohms
40 dB - R 11 and R 35 are 2.4 K ohms
V6 6DJ8 or 6922 Infrasonic amp
Line Board
44 dB - change R 11 and R 35 to 1.5 K ohms
These resistors are located on the circuit
board close to the Phono stages. They are
identified by white ink lettering. Changing
these resistors will simultaneously increase
the gain of the moving coil phono stage, i.e.,
by the same four dB increments.
V1 6DJ8 or 6922 Contour amp
V2 6DJ8 or 6922 Line amp/Bal amp
V3 6DJ8 or 6922 Line amp/Bal amp
Note: 6922 Tubes are preferred as they
have less noise and microphonics than 6DJ8s
Factory set gain of MC Phono is 60 dB.
The gain may be changed independently of
MM Phono as follows:
60 dB - Stock R4 and R28 are 62ohms, 1/2W
65 dB - change R4 and R28 to 33 ohms,1/2W
70 dB - change R4 and R28 to 18 ohms,1/2W
Changing the input impedance
of the phono stage
Change the jumper position on the
headers labeled J6 & J9 to the value recom-
mended by your phono cartridge manufac-
turer. Most moving magnet cartridges work
best at the 47k setting. Moving coil cartridges
typically work best at a lower setting.
22
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Limited Warranty
This Warranty gives you specific legal
Sunfire Corporation is proud of its prod-
ucts which have been built with care using
advanced technology and premium compo-
nent parts. Your unit has been crafted to
perform properly for many years. Sunfire
Corporation offers the following Warranty to
you, the owner of a new Sunfire product:
rights, and you may also have other rights
which vary from state to state. We suggest
that you attach your purchase receipt to this
Warranty and keep these in a safe place.
Thank you for your choice of a Sunfire
Corporation product.
The Sunfire Corporation Warranty for the
Classic vacuum tube preamplifier is in effect
for FIVE years from the date of original retail
purchase. The Sunfire Corporation Warranty
covers defects in materials and workmanship.
The following, however, are excluded:
Service Assistance
We suggest that you read the Limited
Warranty completely to fully understand your
Warranty/Service coverage.
If your Sunfire Corporation product ever
requires service, write to us or call:
Sunfire Corporation
a) Damage caused during shipment
Technical Services Department
P.O. Box 1589
Snohomish, WA 98290
Tel (425) 335-4748
b) Damage caused by accident, misuse,
abuse of operation contrary to the
instructions specified in the Sunfire
Corporation user’s manual
Fax (425) 335-4746
c) Units where the serial number has
been defaced, modified or removed
You will be directed to an authorized
Sunfire Corporation Service Station or receive
instructions to ship the unit to the factory.
Please save the original shipping carton and
packing materials in case shipping is required.
Please do not ship Parcel Post.
d) Damage resulting from modification or
attempted repair by any person not
authorized in writing by Sunfire Corpo-
ration.
The Sunfire Corporation Warranty
extends to the original owner or subsequent
owner(s) during the five year warranty period
so long as the original dated purchase receipt
is presented whenever warranty service is
required.
NOTE: Before sending in your unit for repair,
you must call Sunfire for return authorization.
Include a complete description of the
problem, indicating how you have it con-
nected, the associated equipment in your
system and a copy of your purchase receipt.
Initial shipping costs are not paid by Sunfire
Corporation; return ground shipping costs will
be prepaid if repairs were covered by the
scope of this Warranty.
All implied warranties, including warran-
ties or mechantability and fitness for particular
purposes, are limited in duration to the five
year length of this Warranty, unless otherwise
provided by state law.
Sunfire Corporation’s liability is limited to
the repair or replacement, at our option, of
any defective product and shall not in any
event include property or any other incidental
or consequential damages which may result
from the failure of this product.
Some states do not allow limitations on how
long an implied warranty lasts and/or do not
allow the exclusion or limitation of incidental or
consequential damages, so the above limita-
tions or exclusions may not apply to you.
©2001, Sunfire Corporation. All rights re-
served.
Limited Warranty
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Part number : 913-012-00 Rev C
Download from Www.Somanuals.com. All Manuals Search And Download.
|