®
Sunbeam MultiMincer
Instruction and Recipe Booklet
FG5600
Please read these instructions carefully
and retain for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sunbeam’s Safety Precautions
SAFETY PRECAUTIONS FOR YOUR
SUNBEAM MULTIMINCER.
• Do not contact moving parts at all times.
• Do not put hot meat into the mincer.
• Always use extreme care when handling the
blade and discs.
• All discs and attachments should be removed
with care before cleaning.
• Unplug from power outlet when not in use,
before putting on or taking off attachments,
and before cleaning.
• Only use the pusher that is supplied with this
mincer.
• Only use the attachments and accessories
provided and recommended by Sunbeam.
• Do not overload the mincer.
• Do not operate for more than 1 minute at a
time while mincing heavy loads. This does not
apply to any of the recipes in this booklet.
• Do not put your fingers or any utensil into the
feeder chute.
Sunbeam is very safety conscious when
designing and manufacturing consumer products,
but it is essential that the product user also
exercise care when using an electrical appliance.
Listed below are precautions which are essential
for the safe use of an electrical appliance:
• Read carefully and save all the instructions
provided with an appliance.
• Do not use an appliance for any purpose
other than its intended use.
• Do not place an appliance on or near a hot gas
flame, electric element or on a heated oven.
• Do not place on top of any other appliance.
• Do not let the power cord of an appliance hang
over the edge of a table or bench top or touch
any hot surface.
• Always turn the power off at the power outlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turn the power off and remove the plug
when the appliance is not in use and
before cleaning.
• Do not use your appliance with an extension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Always use your appliance from a power
outlet of the voltage (A.C. only) marked
on the appliance.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Do not operate any electrical appliance with
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
for examination, repair or adjustment.
• For additional protection, Sunbeam
recommend the use of a residual current
device (RCD) with a tripping current not
exceeding 30mA in the electrical circuit
supplying power to your appliances.
• Do not immerse the appliance in water
or any other liquid unless recommended.
• Appliances are not intended to be operated
by means of an external timer or separate
remote control system.
• This appliance is intended to be used in
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
• Children should be supervised to ensure that
they do not play with the appliance.
• The temperature of accessible surfaces may be
high when the appliance is operating.
• Never leave an appliance unattended while
in use.
If you have any concerns regarding the performance and use of your appliance,
3
Ensure the abov
D
e
o
s
w
a
n
f
l
e
o
t
a
y
d
p
fr
r
o
e
m
ca
W
ut
w
io
w
n
.S
s
o
a
m
rean
u
u
n
a
d
lse.c
r
o
s
m
to
.
All Manuals Search And Download.
od.
Features of your Sunbeam
®
MultiMincer
Feeder tray
Use the Feeder Tray to hold food ready
for mincing.
Mincer body
Houses the powerful 600 watt motor.
(1500W Locked Rotar). Delivers high
torque at low speeds to grind and mince
through the toughest meat cuts.
Non-slip rubber feet
Makes the unit sturdy,
preventing it from slipping or
scratching the benchtop.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Food pusher
Guides meat safely through the
chute to hit the mincing screw, for
superior mincing results.
Chute
The chute houses the mincing
screw and blade. Use the food
pusher to direct food through the
chute to the mincing screw and
blade.
Mincing screw
Blade
Mincing discs
(Fine, Medium and Coarse)
Fastening dial
Locks the mincing discs, sausage
and kebbe attachments firmly into
place. Use the spanner to ensure it
is firmly screwed onto the chute.
Food catcher
Place underneath chute for mince
and sausage collection. Also
doubles as a storage unit to store
attachments – use the feeder tray
as the lid.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Attachments for your Sunbeam
®
MultiMincer
Fine disc
Sausage making attachment
(Thick nozzle, thin nozzle, base plate)
Medium disc
Coarse disc
Cleaning disc
Feeder tray
Food catcher
Kebbe making attachments
(Kebbe cone, kebbe shaper)
Spanner
6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using your Sunbeam MultiMincer
Before using your Mincer
6. Align chute into the mincer body, using
arrows as a guide. Press and hold the
Wash all attachments in warm soapy water
using a mild detergent. Dry each part
thoroughly before use.
lock/unlock button to twist and lock into
place.
7. Once the mincer body is in place, tighten
the fastening dial using the spanner to
ensure all elements are securely in place.
See figure 2.
Before you assemble the mincer ensure that
the power cord is unplugged.
NOTE: All attachments must be firmly in
place before using the appliance. Ensure that
the mincing screw and blade are firmly in
place inside the mincer body and the mincer
discs or sausage maker attachments are
secured with the fastening dial.
8. Place the food catcher underneath the
fastening dial for mince collection and
the feeder tray on top of the mincer
chute. See figure 2.
Figure 2
Fitting and using the mincing discs
1. Place the mincer body, facing you on a
level, dry surface.
2. Fit the mincing screw inside the chute.
3. Fit the blade over the mincing screw
ensuring that the flat/smooth side of the
blade faces the mincing screw, away from
the mincing disc.
4. Fit the disc (depending on the type of
mince your require, this will either be a
fine, medium or coarse disc).
5. The fastening dial then fits over the disc
and screws into place. Do not tighten this
fastening dial yet as it will be harder to
lock into the mincer body. See Fig 1.
9. Place prepared meat in feeder tray. Plug
the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
10.Switch the mincer on by pressing ‘ON’
button. Using the food pusher, gently
push meat through the chute.
Figure 1
NOTE: Do not use excessive force to push
meat through the mincing chute as it could
damage the appliance.
CAUTION: Do not use anything else apart
from the pusher supplied with this mincer
to push meat through the chute. NEVER use
your hands/fingers to push meat through the
chute.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using your Sunbeam MultiMincer (continued)
Fitting and using the Sausage attachments
7. Tighten the fastening dial using the
spanner to ensure all elements are
securely in place.
1. Place the mincer body, facing you on a
level, dry surface.
8. Place the food catcher underneath the
fastening dial for sausage collection and
place the feeder tray on top of the chute.
See Fig 4.
2. Fit the mincing screw inside the Chute.
3. Fit the base plate over the mincing screw,
so the dome is facing outwards.
4. Fit either the thick or thin sausage nozzle
over the base plate
Figure 4
5. While holding the sausage nozzle in
place, screw the fastening dial over the
nozzle and loosely secure by screwing on
the fastening dial. See Figure 3.
Figure 3
9. If using fresh sausage skins, soak it in
cold water for approximately 30 minutes
before using on the nozzle attachment.
10.Plug the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
11.Switch on mincer.
12.Using the pusher, push the sausage
mixture into the chute.
6. Align chute into the mincer body using
arrows as a guide. Press the lock/unlock
button and twist to lock into place.
13.As the mixture comes through the nozzle,
ease the skin off as it fills. Twist the skin
at the desired length to form individual
sausages once all of the casings are
filled. See tips on sausage making on
page 12 for further information on
sausage making.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Using your Sunbeam MultiMincer (continued)
Fitting and using the Kebbe attachments
1. Place the mincer body, facing you on a
level, dry surface.
7. Place the feeder tray on top of the chute.
See Fig 6.
2. Fit the mincing screw inside the chute.
3. Fit the kebbe shaper.
Figure 6
4. Fit the kebbe cone over the shaper.
5. Secure the kebbe attachments with
the fastening dial. Loosely secure with
fastening dial – do not use spanner until
chute is locked into mincer body. See
figure 5.
Figure 5
8. Plug the power cord into a 230-240V AC
power outlet and turn the power ‘ON’.
9. Switch on mincer.
10.Using the pusher, push the kebbe mixture
into the chute.
11.Cut kebbe into desired lengths.
Tip: For full kebbe recipe and suggestions see
page 20.
6. Align chute into the mincer body using
arrows as a guide. Press and hold the
lock/unlock button to twist and lock into
place. Use the spanner to tighten the
fastening dial to ensure all elements are
securely in place.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Storing your Sunbeam MultiMincer
®
The Sunbeam MultiMincer was designed
so that all attachments can be stored in two
unique storage components.
1. Attachments can be stored inside the
food pusher as shown below:
2. Storage of food pusher, cleaning disc
spanner and food pusher in Food catcher
/ Feeder tray.
3. Cord Storage: The power cord can be
stored by pushing it into the back of the
motor base.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Handy Hints for Mincing
•
•
Remove all large pieces of fat from meat
before mincing.
•
If changing mincing discs or changing to
another attachment, always ensure that
any meat that is around the fastening
dial or blade is removed. This will ensure
that all parts will reassemble and operate
correctly.
For fatty cuts of meat we recommend
that you cut meat into 5cm cubes.
For lean cuts of meat; cut into strips
approximately 15cm long and 5cm thick
or into cubes.
•
Minced meat should be used within 1-2
days. Freeze uncooked mince that will
not be used within this time frame.
•
•
Remove any bones from meat as this may
damage the mincer.
•
•
Mince can be frozen for 2-3 months
To make sure that all meat has come
through mincing, place a 20cm sheet
of crushed baking paper into the mincer
after the last piece of meat. This will
push through any remaining meat and
will not damage the mincer.
Thaw mince in refrigerator overnight, DO
NOT refreeze uncooked meat.
•
When cooking mince it needs to be
cooked thoroughly. Mince that has been
used for hamburgers or meat patties
should be cooked until well done.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Handy Hints for Sausage Making
•
Salt is an important component of
sausage making. It is responsible for the
control of growth of micro-organisms.
It also aids in dissolving the myosin
(protein) out of the muscle fibres which
then acts as a glue to bind the meat
together.
•
Thing to look for when making sausages:
• Choose good quality ingredients
• Fat to meat ratio (30:70)
• Spices and seasoning should be
combined in amounts that compliment
the type of meat in the sausage.
•
Casings can be purchased from the
butcher that have supplied you with your
fresh meat. If preserved in salt, it should
be soaked in lukewarm water for up to 30
minutes before use. Flush skins with cold
water to expel excess salt.
•
•
Freshly made sausages are better when
allowed to sit in the refrigerator for a
minimum of 12 hours and for up to 24
hours.
Fresh sausages are highly perishable
products as they do not contain the
preservatives that are present in most
store-bought sausages. They should be
cooked within 2-3 days of being made or
frozen.
•
•
Unused fresh casings must be drained,
covered with salt and frozen.
Sausages should be stored in an air tight
container or sealed with cling film in the
refrigerator.
•
•
•
Ideally, sausages should contain up to
30% fat content to provide a tender and
moist product.
•
•
A good way to make sure that all the
sausage mince has come through the
mincer is to break up 1-2 slices of bread
and push though mincer, this will force
any remaining mixture into the casing.
Sausages should be thoroughly cooked to
kill all microbes. Internal temperatures
must reach 70-75°c.
Gentle cooking over medium heat
prevents interior from boiling which in
turn bursts the skin, leaking out moisture
and flavour. This then produces a hard
textured product.
Intentional piercing of sausage skin
releases much needed moisture but
prevents the sausage from possibly
splitting and being disfigured.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
When you have completed mincing, unplug
the mincer from the power outlet.
Warning: Take care in washing all attachment
components to ensure that there is no food
particles left in/around the mincing discs,
sausage/kebbe making attachments, blade
and mincing screw. We do not recommend
dishwashing any of the mincing attachments.
Ensure that all accessories and attachments
are washed thoroughly with hot, soapy water.
To remove meat that is stuck in the fine
and medium discs, align the holes of the
mincing disc with the cleaning disc. Push
the cleaning disc into the mincing disc. As
shown in figure 1.
Note: Always unplug the mincer to clean.
Do not wash/immerse the mincer body in
water – clean this part only by wiping using a
damp cloth.
Any meat stuck in the mincing disc will be
pushed out. Any remaining meat that is still
in the mincing disc should be washed off
using a soft sponge and hot soapy water.
Figure 1
To remove foods from the coarse disc, rinse
disc under cold, running water to force meat
from holes. Any remaining meat stuck on the
mincing disc should be washed off using a
soft sponge and hot soapy water.
Cleaning
disc
Ensure that all attachments and discs are
dried thoroughly before storing. If discs are
not dried, rust may occur on the discs.
Tip: To store mincing discs, we recommend
rubbing a little vegetable oil on the outside of
the discs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes
Breakfast Sausages
Makes approx 1kg
Italian Sausages
Makes approx 1kg
700g pork neck, diced into 5cm pieces
400g chuck steak, diced into 5cm pieces
2 teaspoons onion powder
1.1kg pork neck, diced into 5cm pieces
2 tablespoons finely chopped parsley
1 clove garlic, crushed
2 teaspoons salt
2 tablespoons rice flour
¼ teaspoon ground white pepper
2 teaspoons salt
2 tablespoons rice flour
1 teaspoon ground black pepper
¼ teaspoon cayenne pepper
1
/
3
cup cold water
1. Assemble MultiMincer with the blade and
medium disc.
¼ teaspoon chilli flakes
1
/
3
cup red or white wine
2. Turn MultiMincer on and slowly add beef
pieces into the chute using the food
pusher.
1. Assemble MultiMincer with the blade and
coarse disc.
2. Turn MultiMincer on and slowly add pork
pieces into the chute using the food
pusher.
3. Place mince into large bowl.
4. Whisk remaining ingredients until
smooth; pour flour mixture over the beef
and mix through thoroughly.
3. In a large bowl, combine pork mince,
parsley and garlic.
5. Remove blade and disk and attach base
plate and the thin or thick sausage
making attachment.
4. Whisk remaining ingredients until
smooth; pour over the beef mix and stir
through thoroughly.
6. Thread sausage casing onto nozzle.
5. Remove blade and disc and attach base
plate and the thin or thick sausage
making attachment.
Tip: For thin sausages use a thin casing and
the thin nozzle or for a thick sausage use
a thick casing and the thick nozzle.
6. Thread sausage casing onto nozzle.
7. Turn Multimincer on and add the sausage
mixture into the chute. Once the mixture
starts to come through the nozzle, hold
the casing at the tip of the nozzle to
ensure that the mixture evenly comes
through the casing.
Tip: For thin sausages use a thin casing and
the thin nozzle or for a thick sausage use a
thick casing and the thick nozzle.
7. Turn Multmincer on and add the sausage
mixture into the chute. Once the mixture
starts to come through the nozzle, hold
the casing at the tip of the nozzle to
ensure that the mixture comes through
the casing evenly.
Tip: The type of meat can be varied to your
choice.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Chicken, Spinach and
Pine nut Sausages
Makes approx 1kg
Merguez
(North African Sausages)
Makes approx 1kg
1.1kg chicken thigh fillets, roughly chopped
1 cup firmly packed, finely chopped
1.1kg lamb shoulder, diced into 5cm cubes
1 tablespoon finely chopped mint leaves
2 cloves garlic, crushed
silverbeet – green part only
1
/
3
cup toasted pine nuts
2 tablespoons rice flour
½ teaspoon celery salt
1 teaspoon salt
1 tablespoon sweet paprika
1 tablespoon ground cumin seed
¼ teaspoon ground white pepper
2 teaspoons salt
1
2 tablespoons rice flour
/
3
cup cold water
1
/
3
cup cold water
1. Assemble MultiMincer with the blade and
coarse disc.
1. Assemble MultiMincer with the blade and
coarse disc.
2. Turn MultiMincer on and slowly add lamb
pieces into the chute using the food
pusher.
2. Turn MultiMincer on and slowly add
chicken pieces into the chute using the
food pusher.
3. In a large bowl combine the lamb mince,
mint and garlic.
3. In a large bowl combine the chicken,
silverbeet and nuts.
4. Whisk remaining ingredients until
smooth; pour mixture over the beef mix &
stir through thoroughly.
4. Whisk remaining ingredients until
smooth; pour mixture over the chicken
mix & stir through thoroughly.
5. Remove blade and disc and attach base
plate and the thin or thick sausage
making attachment.
5. Remove blade and disc and attach base
plate and the thin or thick sausage
making attachment.
6. Thread sausage casing onto nozzle.
6. Thread sausage casing onto nozzle.
Tip: For thin sausages use a thin casing and
the thin nozzle or for a thick sausage use a
thick casing and the thick nozzle.
Tip: For thin sausages use a thin casing and
the thin nozzle or for a thick sausage use a
thick casing and the thick nozzle.
7. Turn MultiMincer on and add the sausage
mixture into the chute. Once the mixture
starts to come through the nozzle, hold
the casing at the tip of the nozzle to
ensure that the mixture comes through
the casing evenly.
7. Turn Multimincer on and add the sausage
mixture into the chute. Once the mixture
starts to come through the nozzle, hold
the casing at the tip of the nozzle to
ensure that the mixture evenly comes
through the casing.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Chicken, Lemon Pepper
and Tarragon Sausages
Makes approx 1kg
Sausage rolls
Makes 24
350g blade or chuck steak, diced into
5cm cubes
1.1kg Chicken Thigh Fillets, roughly chopped
350g lamb shoulder, diced into 5cm cubes
1 tablespoon oil
2 tablespoons coarsely chopped fresh
tarragon
1 onion, chopped finely
3 slices bread, crusts removed
¼ teaspoon dried oregano
¼ teaspoon dried basil
2 tablespoons chopped fresh parsley
2 teaspoons Worcestershire sauce
Salt and pepper
3 sheets puff pastry
1 egg, beaten
sesame seeds, optional
¼ teaspoon ground white pepper
2 teaspoons lemon pepper seasoning
1 teaspoon salt
2 tablespoons rice flour
1
/
3
cup cold water
1.Assemble MultiMincer with the blade and
coarse disc.
2.Turn MultiMincer on and slowly add
chicken pieces into the chute using the
food pusher.
1.Assemble MultiMincer with the blade and
fine disc.
3.In a large bowl combine the chicken,
tarragon, lemon and white pepper.
2.Turn MultiMincer on and slowly add beef
and lamb pieces into the chute using the
food pusher.
4.Whisk remaining ingredients until smooth;
pour mixture over the chicken mix and stir
through thoroughly.
3.Heat oil in a skillet and cook onions until
translucent.
5.Remove blade and disc and attach base
plate and the thin or thick sausage making
attachment.
4.Place bread in a bowl of water and remove
immediately. Gently squeeze out some of
the water.
6.Thread sausage casing onto nozzle.
Tip: For thin sausages use a thin casing and
the thin nozzle or for a thick sausage use a
thick casing and the thick nozzle.
5.Combine the onions, bread, herbs, sauce,
salt, pepper and mince. Mix until well
combined.
7.Turn Multimincer on and add the sausage
mixture into the chute. Once the mixture
starts to come through the nozzle, hold the
casing at the tip of the nozzle to ensure
that the mixture evenly comes through the
casing.
6.Place sausage mince into a piping bag
fitted with a wide round nozzle. Cut pastry
in half and pipe a line of mince down the
centre of each pastry half. Roll to enclose.
7.Cut pastry in 4 sausage rolls and place
onto baking trays seam side down. Brush
with egg and sprinkle with sesame seeds.
Bake in hot oven for about 15- 20 minutes
or until golden brown.
Tip: For a different flavour you can replace
lamb with pork neck. For party size sausage
rolls, simply cut into smaller rolls.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Bolognaise
Serves 6
Quick Lasagne
Serves 8-10
1kg topside steak, diced into 5cm cubes
2 tablespoons olive oil
1 quantity bolognaise mixture
375g large instant lasagne sheets
1 medium onion, chopped finely
1 clove garlic, crushed
500g blend grated mozzarella, cheddar and
parmesan cheese
350g fresh ricotta
2 teaspoons dried basil
280g tomato paste
1. Preheat oven to 200°c
1 x 800g can peeled chopped tomatoes
2 cups water
Salt and pepper
2. Lightly grease a 40cm x 22cm (approx)
size deep baking dish. Spoon enough
meat sauce on base to just cover. Place a
layer of lasagne sheets to cover base.
1. Assemble MultiMincer with the blade and
medium disc.
3. Spoon about one third of the remaining
meat sauce over the lasagne sheets to
cover well. Sprinkle about one third of
the blended cheese only over the meat.
Place another layer of lasagne sheets on
top.
2. Turn MultiMincer on and slowly add beef
pieces into the chute using the food
pusher. Reserve and set aside.
3. Heat oil in a large pan over medium high
heat, add onion and garlic and cook 2-3
minutes or until onion has softened.
4. Spoon another one third meat sauce
over the lasagne sheets then spoon the
fresh ricotta over the meat sauce. Top
with more lasagne sheets. Repeat with
the remaining meat sauce and another
one third of the cheese. Top with the last
layer of lasagne sheets and sprinkle with
the remaining cheese.
4. Add dried basil and mince; cook, stirring
frequently, for 4-5 minutes or until mince
is brown and crumbly.
5. Stir in tomato paste and cook for 1
minute; add chopped tomatoes and water
and bring to the boil. Reduce heat to
medium, cover and simmer 20 minutes or
until mixture has reduced and thickened.
5. Loosely cover lasagne with aluminium
foil and bake for 40 minutes. Remove
foil and bake, uncovered, for a further 20
minutes or until the top is golden and the
lasagne sheets are cooked. To test, place
a small sharp knife through the lasagne,
if soft the sheets are cooked.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Sang Choi Bow
Serves 4 as an entrée
Red Curry Paste
Makes approx 1 cup
You will need approximately 400g of
chicken breast for this recipe. Pork can be
substituted in this recipe. We recommend
using the medium disc.
2 teaspoons shrimp paste
16 – 20 dried long red chillies
2 teaspoons salt
2 tablespoons chopped galangal
4 tablespoons chopped lemongrass
6 kaffir lime leaves, stems removed and
sliced thinly
3 green onions
1 tablespoon peanut oil
1 clove garlic, crushed
½ teaspoon grated fresh ginger
6 fresh shitake mushrooms, chopped finely
350g chicken mince
4 lettuce leaves, to serve
2 teaspoons sesame seeds, toasted
2 teaspoons scraped and chopped coriander
root
¼ cup chopped red shallots
1
/
3
cup chopped fresh garlic
1. Preheat a grill on High. Wrap shrimp paste
in aluminium foil and place onto a baking
tray. Grill 1-2 minutes and turn over and
repeat. Alternatively place onto a hot
Sauce
1 tablespoon shao hsing wine
1 tablespoon light soy sauce
1 tablespoon oyster sauce
1 tablespoon hoisin sauce
1 teaspoon sesame oil
1 teaspoon white sugar
barbeque hot plate and cook 1-2 minutes
each side. Remove and set aside to cool.
2. Remove stalks and seeds from chillies;
place in a bowl. Pour over boiling water
to cover and soak for 20 minutes or until
softened. Drain chillies and roughly chop.
Place chillies into a bowl with remaining
ingredients; mix well.
1. Separate white and greens parts of onions.
Finely chop the white parts and thinly
slice the green. Keep separate and set
aside.
3. Assemble MultiMincer with the blade and
fine disc.
2. Heat oil in a wok over high heat, add
garlic, ginger, mushrooms and white
parts of green onions and cook stirring
frequently for 1 minute.
4. Turn MultMincer on and slowly add paste
ingredients into the chute using the
food pusher. Repeat once or twice more
depending on the fineness of paste you
require.
3. Add chicken mince and cook 3-4 minutes
or until golden and crumbly.
4. Combine sauce ingredients in a separate
bowl, mix well. Pour into chicken mince
and stir-fry 3 minutes or until chicken
mince is cooked and sauce has thickened.
Stir through green parts of green onions.
5. Store paste in an airtight container for up
to 3 days. Alternatively, freeze for up to 6
months.
5. Spoon into lettuce cups, sprinkle with
sesame seeds and serve immediately.
Tip: Shoa Hsing wine, oyster sauce, hoisin
sauce and sesame oil are all available in
Asian supermarkets.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Thai Chicken Red Curry
Serves 4
Matt’s Meatballs
Serves 6-8
1 tablespoon vegetable oil
1 onion, cut into thin wedges
1 portion home made red curry paste
1 x 400ml can coconut milk
2 teaspoons sugar
1.3kg lean beef
2
/
3
cup packaged breadcrumbs
3 eggs
2 tablespoons Worcestershire sauce
2 teaspoons dried sweet basil
1 teaspoon dried oregano
2 cloves garlic, crushed
salt and pepper
1 tablespoon fish sauce
750g chicken breast fillet, sliced thinly
1 red capsicum, deseeded and sliced
230g can bamboo shoots, drained
100g sugar snap peas
2 tablespoons olive oil
Sauce
Coriander leaves, to serve
1 onion, sliced
1. Heat oil in a wok over high heat, add
onion and cook 1-2 minutes, stirring
frequently or until softened.
2 cloves garlic, crushed
2 tablespoons tomato paste
1 green capsicum, sliced
1 red capsicum, sliced
1 litre bottled tomato sauce
2. Add red curry paste and cook 1 minute.
Reduce heat to medium and stir in
coconut milk, sugar and fish sauce.
1. Assemble MultiMincer with the blade and
fine disc.
3. Add chicken and capsicum and simmer
for about 3 minutes or until chicken is
just cooked. Stir through bamboo shoots
and sugar snap peas and simmer a further
1-2 minutes.
2. Turn MultiMincer on and slowly add beef
pieces into the chute using the food
pusher.
3. Combine meatball ingredients; roll into
balls slightly smaller than golf balls.
4. Serve hot with steamed jasmine rice and
fresh coriander leaves.
4. Heat half of the oil in a frying pan over a
medium heat. Cook meatballs, in batches,
until browned all over. Remove from pan.
Tip: If using store bought curry paste use 2-3
tablespoons to taste.
5. Heat remaining oil in frying pan; cook
onions and garlic, stirring, until the
onions are translucent. Add tomato paste
and cook for about 1-2 minutes or until
fragrant. Add capsicums; cook, stirring
occasionally, until tender. Add sauce and
cook for 10 minutes. Reduce heat; add
meatballs and cook, covered, for a further
10 minutes or until the meatballs are
cooked through.
6. Serve in long crusty bread rolls as a sub
sandwich or with pasta.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Recipes (continued)
Kebbe
FILLING
1. Assemble MultiMincer with the blade and
medium disc.
Outer casing
500g fine cracked wheat (burghul)
500g lean lamb loin, cubed
1 small onion, roughly chopped
1 teaspoon ground black pepper
1 teaspoon ground white pepper
1 tablespoon sea salt
2. Turn MultiMincer on and slowly add lamb
pieces into the chute using the food
pusher.
3. Heat butter in a large frying pan over
medium heat. Add pine nuts and cook
2-3 minutes or until golden. Remove and
set aside.
Filling
4. Fry onion in same pan until golden.
350g lamb leg steak, cubed
20g butter
5. Add lamb mince and cook for 5-
6 minutes or until browned (do not
overcook). Season with salt and pepper.
Stir through mint and pine nuts. Allow to
cool completely.
25g pinenuts
1 medium onion, chopped finely
2 tablespoons chopped fresh mint
¼ teaspoon ground black pepper
¼ teaspoon ground white pepper
1 teaspoon sea salt
TO ASSEMBLE
1. Assemble MultiMincer with the kebbe
making attachments.
2. Turn MultiMincer on and push the casing
mixture through the chute using the food
pusher.
OUTER CASING
1. Place cracked wheat in a large bowl
and cover with cold water. Allow to soak
for minimum of 30 minutes, drain and
reserve.
3. Cut into 8cm (3 inch) lengths.
4. Pinch one end of the tube to seal it.
Spoon a little filling, into the other end,
then seal.
2. Assemble MultiMincer with the blade and
fine disc.
5. Deep fry in hot oil for about 6 minutes or
until golden brown.
3. Turn MultiMincer on and mince lamb; add
the onion before the last batch.
Tip: Kebbe can be frozen. Kebbe can be
cooked fresh or straight from the freezer.
This will take approximately 3-4 minutes
fresh, or 4-6 minutes from frozen. Please be
careful when frying as oil may spatter.
4. In a large bowl combine the meat with
the cracked wheat, pepper and salt. Mix
by hand until thoroughly combined.
5. Remove fine mincing disc and blade and
insert medium disc without blade. Place
lamb and cracked wheat mixture through
mincer. Refrigerate for 1 hour.
Kebbe recipe courtesy of Chemouni Elsayed
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Month Replacement Guarantee
In the unlikely event that this appliance develops any malfunction
within 12 months of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
Should you experience any difficulties with
your appliance, please phone our customer
service line for advice on 1300 881 861 in
Australia, or 0800 786 232 in New Zealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
In Australia you are entitled to a
replacement or refund for a major failure and
for compensation for any other reasonably
foreseeable loss or damage. You are also
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
a major failure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
Your Sunbeam 12 Month Replacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
For a complete list of Sunbeam’s authorised
service centres visit our website or call:
Australia
Similarly your 12 Month Replacement
Guarantee does not cover freight or any other
costs incurred in making a claim. Please
retain your receipt as proof of purchase.
1300 881 861
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
New Zealand
0800 786 232
26 Vestey Drive, Mt Wellington
Auckland, New Zealand
Our goods come with guarantees that cannot
be excluded under the Australian Consumer
Law and under the New Zealand Consumer
Guarantees Act.
Download from Www.Somanuals.com. All Manuals Search And Download.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Or call 1300 881 861
In New Zealand
Or call 0800 786 232
is a registered trademark.
‘Sunbeam MultiMincer’ is a registered trademark of Sunbeam Corporation.
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright. Sunbeam Corporation Limited 2011.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
8/11
Download from Www.Somanuals.com. All Manuals Search And Download.
|