Sun Microsystems Network Router STP2002QFP User Manual

STP2002QFP

Revision 1.0–April 1996

STP2002QFP

Fast Ethernet, Parallel Port, SCSI

(FEPS)

USER’S GUIDE

OVERVIEW

1.1 Introduction

The STP2002QFP FEPS (Fast Ethernet , Parallel, SCSI) is an ASIC that pro-

vides integrated high-performance SCSI, 10/100 Base-T Ethernet, and a Cen-

tronics compatible parallel port.

1.2 Features

FEPS features include the following:

• IEEE 1496 SBus master interface with support for 64-bit mode access

• IEEE 1496 SBus slave interface, 32-bit mode only

• 20 MB/s fast and wide single-ended SCSI using a QLogic FAS366 core

• 10/100-Mb/sec Ethernet on the motherboard

• MII (Media Independent Interface) interface to support external transceivers

• DMA2-compatible Centronics parallel port with a maximum throughput of 4

MB/s

• Supports use on an SBus card device

• Provides a path to an FCode PROM for use on SBus boards

• JTAG support for boundary and internal scan testing

1.3 Overview

FEPS contains four major blocks: SBus Adapter (SBA), SCSI_Channel,

ENET_Channel, and PP_Channel. Each channel uses the Channel Engine In-

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

109 rev10h, ISO/IEC 8802-3, IEEE 802.3u 100 Base-T, IEEE 1149.1 (

JTAG), Centronics-protocol-compatible parallel port, and the Sun4u system

architecture.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

SBus

SBA

Channel Engine Interface

ENET_IRQ

PP_IRQ

SCSI_IRQ

SCSI DVMA

ENET DMA

PP DMA

PP Core

FAS366

BigMac

SCSI_Channel

ENET_Channel

PP_Channel

SCSI

Bus

MII

Interface

Boot PROM

Parallel Port

Figure 1. STP2002QFP Block Diagram

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

1.6 Pin Descriptions

The signal pins are grouped by function in the following tables.

Table 1: SBus Signals

Signal Name

SB_D[31:0]

Type

I/O

Pin Count

Description

SBus data

SB_A[27:0]

SB_SEL

SBus address

SBus slave select

SB_BR

SBus DVMA request

SBus DVMA grant

SB_BG

SB_ACK[2:0]

SB_SIZ[2:0]

SB_RD

I/O

SBus acknowledge codes

SBus transfer size

SBus direction

SB_CLK

SBus clock

SB_RESET

SB_AS

SBus reset

SBus address strobe

SBus late error

SB_LERR

SB_DATAPAR

SB_SC_INT

SB_ET_INT

SB_PP_INT

Total SBus

I/O

SBus data parity

SCSI interrupt request to the system

Ethernet interrupt request to the system

Parallel port interrupt request to system

Table 2: SCSI Signals

Signal Name

SCSI_D[15:0]

SCSI_DP[1:0]

SCSI_SEL

Type

Pin Count

Description

SCSI data

I/O

SCSI data parity

SCSI select

SCSI_BSY

SCSI_REQ

SCSI_ACK

SCSI_MSG

SCSI_CD

SCSI busy

SCSI request

SCSI acknowledge

SCSI message phase

SCSI command/not data

SCSI direction

SCSI attention

SCSI_IO

SCSI_ATN

SCSI_RST

SCSI reset

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 2: SCSI Signals

Signal Name

SCSI_XTAL2

Type

Pin Count

Description

SCSI crystal output

SCSI_XTAL1

POD

SCSI crystal input

SCSI power detect

Total SCSI

Table 3: Ethernet Signals

Signal Name

ENET_TX_CLK

ENET_TXD[3:0]

ENET_TX_EN

ENET_COL

Type

Pin Count

Description

Ethernet transmit clock input

Ethernet transmit data

Ethernet transmit enable

Ethernet transmit collision detected

Ethernet carrier sense

ENET_CRS

ENET_RX_CLK

ENET_RXD[3:0]

ENET_RX_DV

ENET_RX_ER

ENET_MDC

Ethernet receive clock

Ethernet receive data

Ethernet receive data valid

Ethernet receive error

I/O

Ethernet management device clock

ENET_MDIO0

Ethernet management device I/O data for

on-board transceiver

ENET_MDIO1

I/O

Ethernet management device I/O data for

on-board transceiver

ENET_BUFFER_EN

Ethernet buffer enable

ENET_TX_CLKO

Total Ethernet

Ethernet transmit clock output

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 4: Parallel Port Signals

Signal Name

PP_DATA[7:0]

PP_STB

Type

I/O

Pin Count

Description

Parallel port data bus

Parallel port data strobe

Parallel port busy

PP_BSY

PP_ACK

Parallel port acknowledge

Parallel port paper error

Parallel port select

PP_PE

PP_SLCT

PP_ERROR

PP_INIT

Parallel port error

Parallel port initialize/ALE high address byte

Parallel port select in

PP_SLCT_IN

PP_AFXN

PP_DSDIR

PP_BSYDIR

PP_ACKDIR

PP_DDIR

Parallel port audio feed/ALE low address byte

Parallel port data strobe direction

Parallel port busy direction

Parallel port ack direction

Parallel port data direction

ID_CS

I/O

ID PROM chip select

Total Parallel Port

Table 5: JTAG/Miscellaneous Signals

Signal Name

JTAG_TDO

JTAG_TDI

Type

Pin Count

Description

JTAG test data out

JTAG test data in

JTAG test mode select

JTAG clock

JTAG_TMS

JTAG_CLK

JTAG_RESET

STOP_CLOCK

CLK_10M

JTAG TAP reset

Stop clock input

10-MHz clock output

Total JTAG

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 6: Power/Ground/Other Signals

Signal Name

VDD_CORE

Type

Pin Count

Description

VSS_CORE

Reserved

MODE

Total

Mode select (stand alone/chipset)

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

SBUS ADAPTER

2.1 Introduction

The SBus Adapter (SBA) is the layer between the Channel Engine Interface

(CEI) and the SBus. It provides one master port on the SBus side to funnel

three DMA channel engines (CE) onto the SBus, and one slave port for SBus

accesses to the CEs. The SBA can be viewed as a block of data path and flow

control between SBus and channel engine interface.

2.2 SBus Capabilities

2.2.1 Slave Accesses

• Supports byte/half-word/word access, but not burst transfer

• Supports 32-bit transfer mode

• Parity generation/checking

• Does not generate late error

• Does not generate Rerun Ack

• Maximum latency < 22 SBus clocks

2.2.2 Master Accesses

• Compliant to IEEE 1496

• Supports 64-bit/32-bit transfer mode

• Supports byte/half-word/word transfer size

• Supports burst transfer size from 8 bytes to 64 bytes

• Parity generation/checking

• Does not issue atomic transaction

• Does not support bus sizing

2.2.3 Address Decoding

In order to eliminate the need of NEXUS driver in between FEPS device driv-

er and the kernel there are no registers insides the SBA block (a register inside

SBA would be a global register which means a NEXUS driver is needed).

However, SBA does decode the physical address input and the access size for

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

slave accesses from SBus. The physical address is decoded to select a target

CE to respond to the access. A physical address that cannot be resolved to the

selection of any channel engine will cause SBus Adapter to return Error Ack.

The access size is decoded to Error Ack 64-bit transfer mode or burst transfer

that is not supported by FEPS.

2.3 Theory of Operation

2.3.1 Master Operations

All master operations are originated from the channel engines. The operations

start when one or more bus requests are asserted on the channel engine inter-

face.

2.3.1.1 DVMA Write

DVMA write cycle starts when the channel engine with highest priority as-

serts BR signal on CEI with RD (bit[63] of CE_DOUT signal) signal de-as-

serted. The arbiter inside SBA asserts grant signal (BG) to the requesting CE

and kick off the CEI write state machine. CEI write state machine first latches

the DVMA address, transfer size and channel ID from the requesting CE and

then begin to move data from CEI and write them to the current DVMA data

write buffer. When the whole burst of write data are written to the write buff-

er, the CEI state machine places a write request into the request command

queue of the SBus Master Port State machine and, at the mean time, it release

the arbiter to arbitrate the next request on the CEI. The master port state ma-

chine wakes up and requests the SBus whenever there is a request in the

queue. When the whole burst of Data is written to the SBus, the master port

state machine return the acknowledgment (MEMDONE) and status

(CE_DWERR) to the corresponding CE.

When a CE is granted for DMA write, the CEI bus is locked until the whole

burst of write data is moved over to the write data buffer. During this period,

only the slave write operation from the SBus can occur on the CEI. A slave

read would have to wait until the DMA write cycle is done. On the other hand,

a slave read operation will have the same effect as DMA write that will also

lock up the CEI for the duration of the whole transaction.

2.3.1.2 DVMA Read

DVMA Read cycle starts with the highest priority channel engine asserts BR

signal on CEI with RD (bit[63] of CE_DOUT signal) signal asserted. The ar-

biter latches the DVMA address, transfer size and channel ID and places a

Read request into the request command queue of the SBus master port state

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

machine. After this the arbiter is available to arbitrate and grant the next re-

quest on the CEI provided that there is a DMA write or read buffer still avail-

able. The master port state machine wakes up and request the SBus whenever

there is a request in the queue. When SBus is granted, the master port state

machine asserted BG to the corresponding CE and pass the read data over to

the CEI bus.

2.3.2 Slave Operation

When both AS and SEL input signals are asserted, the slave port begin to re-

spond to the slave access from the SBus. Based on the physical address, one

of the channel engines is selected to respond to the slave access. Slave writes

goes directly through to the CEI bus without arbitration because it share the

CEI data-in data bus with DVMA read which is mutually exclusive to slave

operation. Slave reads share the CEI data-out bus with all other CEI opera-

tions and have to go through arbiter to compete with channel engines.

Because a SBus DVMA read operation may encounter a retry, there is con-

dition that a CE is being granted with DVMA read and a slave access still

comes in. The CE has to make sure that it can still respond to this slave access

under this condition.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

SCSI CHANNEL

3.1 Introduction

The SCSI channel consists of SCSI DVMA (also referred to as SCSI channel

engine) and FAS366, a “Fast and Wide” SCSI controller core. The SCSI

DVMA provides two 64-byte buffers used to transfer data to/from the

FAS366. The FAS366 supplies a 16-bit SCSI data path and a throughput of

20 MB/sec. All programmed I/O access to the FAS366 is driven by the SCSI

DVMA.

Several programmable registers can be used by the SCSI device driver to

direct the SCSI engine and FAS366 to move blocks of data to/from host

memory or to/from devices on the SCSI bus. Once the transfer is complete,

an interrupt is generated on the SBus to inform the driver that block move-

ment is complete, freeing it to initiate further transfers.

3.2 SCSI DVMA

SCSI DVMA is responsible for data movement between FAS366 and the host

memory. It contains two 64-byte buffers. The purpose for providing these

buffers is to have prefetch capability. With this scheme of prefetch buffers,

one buffer can be used for writing/reading data on SBus, while the other buff-

er can be used for reading/writing data from/to FAS366. For SCSI write op-

eration (reading from host memory and writing to FAS366), a chunk of data

is moved from the host memory and stored in the buffers. When FAS366 is

ready to accept data, this data is written to FAS366. For SCSI read operation

(reading from FAS366 and writing to host memory), data being read from

FAS366 is stored in the buffers. This data is written into host memory at a lat-

er time. The whole idea of providing buffers is to absorb the difference in data

transfer rate, between SBus and SCSI bus.

3.3 FAS366

FAS366 is a Fast and Wide SCSI controller core and is integrated into FEPS

as a hard macro.

The following are some of the features of the FAS366 core:

• Supports ANSI X3T9.2/86-109 (SCSI-2) standard

• Sustained SCSI data transfer rates:

- 10-MHz synchronous (fast SCSI)

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

- 5-MHz synchronous (normal SCSI)

- 6-MHz asynchronous

• REQ/ACK programmable assertion/deassertion control

• Power-on connect/disconnect to SCSI bus (hot plugging)

• Target block transfer sequence

• Initiator block transfer sequence

• Bus idle timer

• Reduced SCSI bus overhead

• On-chip, single-ended SCSI drivers (48 mA)

• Target and initiator modes

• 16-bit recommand counter

• Differential mode support

For more information on FAS366, refer to the FAS366 specification from

Emulex.

3.4 Test Support

The SCSI DVMA will support full internal and boundary scan. The FAS366

core does not support full internal scan. SCSI I/O pads will support boundary

scan.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

PARALLEL PORT CHANNEL

4.1 Introduction

The parallel port interface implementation of FEPS is almost identical to the

one on the STP2000 Master I/O controller chip to leverage the existing device

driver. The only difference is that the DIR bit has to be set during a memory

clear operation. It allows the CPU to send data to the standard Centronics

printer in both programmed I/O and DMA modes. The parallel interface can

support bidirectional transfers using Xerox and IBM schemes. A 64-byte

buffer is used to buffer data to and from the channel engine interface and the

parallel port in DMA mode, depending on the direction of the transaction. In

synchronous mode, the port can support data transfer rate up to 4 Mbytes/s.

The parallel port interface also provides the data path to read the FCode

PROM when the FEPS chip is used on a SBus extended card. Two external

8-bit latches are needed to latch the MSB and LSB of the EPROM address.

Refer to the FEPS Application note for more details on this mode.

4.2 Parallel Port FIFO Operation

Between the parallel port and the SBus interface is a 64-byte FIFO (P_FIFO).

This FIFO is bypassed for slave accesses to the parallel port registers. Con-

sistency control ensures that all data written by the external device gets to

main memory in a deterministic manner, and is handled completely in hard-

ware. One of the consistency control mechanisms used on transfers to mem-

ory is draining of all P_FIFO data upon the access of any parallel port register.

The conditions that cause data in the P_FIFO to be drained to memory are

as follows:

1. 4, 16, or 32 bytes (depending on P_BURST_SIZE) have been

written into the P_FIFO.

2. The P_INT_PEND bit in the P_CSR is set.

3. The CPU does a slave write to a parallel port internal register

other than the P_TST_CSR (writing P_ADDR does not cause

draining if P_DIAG is set).

4. The P_RESET or P_INVALIDATE bit in the P_CSR is set.

5. The P_ADDR register is loaded from P_NEXT_ADDR when

P_DIAG is not set.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

None of these conditions will cause draining if P_ERR_PEND = 1, indi-

cating that a memory error has occurred. If condition 4 or 5 occurs when the

P_ERR_PEND bit is 1, the P_FIFO will be invalidated and all dirty data will

be discarded.

4.3 Bidirectional Parallel Port Interface

The parallel port can operate unidirectionally or bidirectionally in either a

programmed I/O mode or in a DMA mode. The hardware interface can be

configured to operate with a wide range of devices through the following

mechanisms:

• Bidirectional signal conﬁguration for the interface control signals—

data strobe, acknowledge, and busy. Each control signal can be indi-

vidually conﬁgured as a unidirectional or bidirectional signal.

• Programmable pulse widths for all generated signals and programma-

ble data setup time for data transfers.

• Programmable protocol deﬁnition for all combinations of acknowl-

edge and busy handshaking.

This interface configuration capability will allow operation over a wide

range of data transfer rates and protocol definitions.

4.3.1 DMA Mode

Since no software intervention is required for data transfer, the interface pro-

tocol and timing required must be programmed via the configuration regis-

ters. DMA transfers are initiated/enabled by setting the P_EN_DMA bit of

the P_CSR. The operation of the interface is dependent on the direction of

transfer and the protocol selected as described below.

4.3.1.1 Unidirectional Operation (Transfers to the Peripheral Device)

This mode of operation is the Centronics implementation of a unidirectional

parallel port. Operation of the parallel port in this mode requires the direction

control bit (DIR) of the transfer control register (TCR) to be 0. Timing vari-

ations are handled via the DSS (data setup to data strobe) and DSW (data

strobe width) bits of the hardware configuration register. The timebase for

programmability is the SBus clock. The DSS parameter (7 bits) can be pro-

grammed from a minimum of 0 SBus clocks to 127 SBus clocks in steps of

one SBus clock. The DSW parameter (7 bits) is also programmed in steps of

one SBus clocks, however when DSW= 0, 1, 2, or 3, data strobe width is de-

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

fined as three SBus clocks. That is, the minimum data strobe width is three

SBus clocks. The following table shows the nominal range of programmabil-

ity for different SBus clock speeds.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 7:

SBus Clock

16.67 MHz

20 MHz

DSS

DSW

0–7.62 µs

0–6.35 µs

0–5.08 µs

180.0 ns–7.62 µs

150.0 ns–6.3 µs

120.0 ns–5.08 µs

25 MHz

The desired handshake protocol can be selected using the ACK_OP

(acknowledge operation) and BUSY_OP (busy operation) bits of the opera-

tions configuration register (OCR). The function of these bits is defined as

follows:

ACK_OP

1 = Handshake complete with receipt of P_ACK (PP_ACK).

0 = P_ACK (PP_ACK) is ignored.

BUSY_OP

1 = Handshake complete with receipt of P_BSY (PP_BSY).

0 = P_BSY (PP_BSY) is not used for handshaking.

These two bits allow selection of one of four possible protocols, however

only three of these protocols make sense and are valid selections. The case of

ACK_OP=BUSY_OP=1, is not supported. For all protocol selections, if

P_BSY (PP_BSY) is active, further data transfers will not occur until P_BSY

(PP_BSY) is negated. The following table summarizes the protocol defini-

tions for transfers to the peripheral device.

Table 8:

BUSY_OP

ACK_OP

Protocol Definition

No handshaking occurs

Acknowledge is required for each byte transferred

P_BSY is used as acknowledge and is required for each byte

transferred. ACK is ignored

Invalid

The transfer modes are shown and discussed in the following sections.

4.3.1.1.1 No Handshake (BUSY_OP=0, ACK_OP=0)

Data transfers are controlled by the use of P_D_STRB (PP_STB) and option-

ally P_BSY (PP_BSY). There is no acknowledge in this mode and P_ACK

(PP_ACK) is a don’t care. P_BSY (PP_BSY) is used to gate further transfers

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

when the peripheral device cannot receive another byte of data. P_BSY

(PP_BSY) is sampled before data strobe becomes active and after data strobe

becomes inactive, to ensure that a data transfer is not attempted while the de-

vice is busy.

It is this mode, which provides the fastest transfer of data over the inter-

face, the fastest cycle time is six SBus clocks per byte. This transfer time is

arrived at as follows: DSS=0, DSW=3 (minimum width of DSW is three

SBus clocks), and three SBus clocks between consecutive data strobes. This

assumes that P_BSY (PP_BSY) is not asserted during the transfer cycle. Ref-

erence Figure 2.

P_DATA (O)

DSS

P_D_STRB (O)

DSW

P_ACK (I)

P_BSY (I)

Don’t Care

1. Data setup as defined in the hardware configuration register.

2. Data strobe width as defined in the hardware configuration register.

3. There is a three SBus clock delay from the end of data strobe to the next byte of data being clocked onto the P_DATA

bus.

4. Acknowledge is a don’t care condition for all data transfers.

5. When P_BSY is active, it gates further data transfers.

Figure 2.

4.3.1.1.2 Handshake with Ack: BUSY_OP=0, ACK_OP=1)

Data transfers are controlled by the use of P_D_STRB (PP_STB), P_ACK

(PP_ACK), and optionally P_BSY (PP_BSY). P_ACK (PP_ACK) is re-

quired for each byte transferred. If P_BSY (PP_BSY) is active at the end of

the cycle, further data transfers will be gated until P_BSY (PP_BSY) be-

comes inactive. If P_BSY (PP_BSY) is not present, then data transfers will

proceed. P_BSY (PP_BSY) is also sampled immediately before P_D_STRB

(PP_STB) is generated to ensure that a data transfer is not attempted while the

device is busy. Reference the data transfer diagram in Figure 3.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

P_DATA (O)

DSS

DSW

P_D_STRB

(O)

P_ACK (I)

1. Data setup as defined in the hardware configuration register.

2. Data strobe width as defined in the hardware configuration register.

3. Acknowledge is required for each byte transferred.

4. When P_BSY is active, it gates further data transfers.

5. If P_BSY is not present, the next data byte will be gated on to the bus following ACK (there is a minimum of three SBus clocks between

the trailing edge of ACK and the next data byte).

6. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 3.

4.3.1.1.3 Handshake with Busy (ACK_OP=0, BUSY_OP=1)

Data transfers are controlled by the use of P_D_STRB (PP_STB) and P_BSY

(PP_BSY). P_ACK (PP_ACK) is a don’t care in this mode. P_BSY

(PP_BSY) is required as an acknowledge after P_D_STRB (PP_STB) and

will gate any further data transfers while it is active. P_BSY (PP_BSY) is also

sampled immediately before P_D_STRB (PP_STB) is generated to ensure

that a data transfer is not attempted while the device is busy. Reference the

data transfer diagram in Figure 4.

P_DATA (O)

DSS

P_D_STRB

(O)

DSW

Don’t Care

P_ACK (I)

1. Data setup as defined in the hardware configuration register.

2. Data strobe width as defined in the hardware configuration register.

3. Acknowledge is a don’t care condition for all data transfers.

4. P_BSY is required as an acknowledge for each byte transferred. While P_BSY is present, it gates fuirther data transfers.

5. The next byte of data will be gated on to the bus following the trailing edge of P_BSY (there is a minimum of three SBus clocks between

the trailing edge of P_BSY and the next byte of data).

6. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 4.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

4.3.1.2 Bidirectional Operation

STP2002QFP

Bidirectional data transfer over the parallel port can be accomplished by the

use of either of two master/slave protocols. The “master write” protocol or the

“master read/write” protocol. The IBM implementation of a bidirectional par-

allel port uses the master write protocol in which the master always writes

data to the slave and when the direction of data transfer needs to be reversed,

mastership is exchanged. The Xerox implementation uses the master

read/write protocol where data transfer is performed in either direction under

control of the fixed master. The parallel port will operate as either master or

slave when configured for master write protocol, and only as the master when

configured for the master read/write protocol.

The selection of one of these bidirectional transfer methods is accom-

plished indirectly through the specification of the bidirectional nature of the

data strobe signal. Since in both methods data strobe resides with the master,

a bidirectional data strobe implies the IBM master write scheme and a fixed

data strobe (output only) implies the Xerox master read/write scheme.

The interface control signals—data strobe, acknowledge, and busy—are

individually configurable as bidirectional or unidirectional pins. The bidirec-

tional signal configuration bits are located in the operation configuration

DS_DSEL

1 = P_DS (PP_DSDIR) is bidirectional, master write protocol selected.

0 = P_DS (PP_DSDIR) is ﬁxed as output. Master read/write protocol

selected.

ACK_DSEL

1 = P_ACK (PP_ACK) is bidirectional.

0 = P_ACK (PP_ACK) is ﬁxed as an input.

BUSY_DSEL

1 = P_BSY (PP_BSY) is bidirectional.

0 = P_BSY (PP_BSY) is ﬁxed as an input.

To allow external driver/receiver connection, each of these control signals

and the data bus has a corresponding direction control pin. The DIR bit of the

transfer control register is used to switch the direction of the data bus and the

pins that have been configured as bidirectional. The state of the DIR bit is

reflected on the P_D_DIR (PP_DDIR) pin for external transceiver control

and direction control communication to the attached device. While DIR=0,

all pins remain in their unidirectional sense which is defined to be consistent

with the unidirectional parallel port as follows:

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 9:

Signal

I/O

DIR_Pin

State

P_D_STRB (PP_STB)

P_ACK (PP_ACK)

P_BSY (PP_BSY)

P_DATA (PP_DATA)

P_DS_DIR (PP_DSDIR)

P_ACK_DIR (PP_ACKDIR)

P_BSY_DIR (PP_BSYDIR)

P_D_DIR (PP_DDIR)

When DIR is set to 1, the pins configured as bidirectional change direction

and their corresponding direction control pins are set accordingly. Note that

the input status pins (ERR, SLCT, PE), which are readable in the input regis-

ter, are not configurable. They are fixed as inputs. Similarly, the output pins

(PP_AFXN, PP_INIT, PP_SLCT_IN) of the output register are fixed as

outputs.

The transfer modes are shown and discussed in the following sections.

4.3.1.3 Master Write Protocol, Slave Operation

This section describes the parallel port operation as a slave when it is config-

ured for master write protocol (DS_DSEL=1). Operation as a master is the

same as is described in the “Unidirectional Operation (Transfers to the Pe-

ripheral Device)” section on page 15.

In this mode, acknowledge and/or busy can be generated in response to a

data strobe. The width of the P_ACK (PP_ACK) pulse can be defined using

the DSW bits of the hardware configuration register. The P_BSY (PP_BSY)

hold time and P_ACK (PP_ACK) positioning after the trailing edge of data

strobe are defined using the DSS bits. However, note that in this mode DSS

has a tolerance of +3 to 4 SBus clocks, due to synchronization delays. The

nominal programmability range is the same as was specified in the “Unidirec-

tional Operation (Transfers to the Peripheral Device)” section on page 15.

The ACK_OP and BUSY_OP bits are used to specify handshake protocol.

The function of the bits take on a new meaning when the parallel port is a

slave.

ACK_OP

1 = Generate P_ACK (PP_ACK) in response to a data strobe.

0 = P_ACK (PP_ACK) is not generated. P_ACK is held in an inactive state.

BUSY_OP 1 = Generate P_BSY (PP_BSY) as an acknowledge, in response to data strobe.

0 = P_BSY (PP_BSY) is not generated for each byte transferred, but is asserted

as required.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

These two bits allow selection of one of four possible handshake protocols.

The following table summarizes the protocol definitions for transfers to the

parallel port from the peripheral device.

For all protocol selections, P_BSY (PP_BSY) will become active if one of

the following conditions occur: The P_DMA_ON bit is reset indicating

DMA cannot proceed; or the

P_FIFO is unable to accept more data. Internally, P_BSY (PP_BSY) will

always be generated for these conditions. However, if the P_BSY (PP_BSY)

pin is not configured as an output, it will not be driven and the external inter-

face will not be able to detect the busy condition. In this case, data could be

lost. In all cases, if P_BSY (PP_BSY) is asserted it will have the following

timing characteristics:

P_D_STRB

(I)

DSS

1. WHen data strobe is detected, P_BSY will be generated within 3 SBus clocks, if required.

2. P_BSY hold time after data strobe is configurable via DSS.

Figure 5.

The transfer modes are shown and discussed in the following sections.

4.3.1.3.1 No Handshake: (BUSY_OP=0, ACK_OP=0)

No handshake signals are generated in this mode. If P_ACK (PP_ACK) is

configured as an output, it will remain low or inactive. P_BSY (PP_BSY) will

be generated as required to gate further transfers, but not as a handshake sig-

nal. The operation of the interface as defined assumes the bidirectional sense

of each signal has been configured as follows: DIR=1, DS_DSEL=1,

ACK_DSEL=X, BUSY_DSEL=1. If P_ACK (PP_ACK) is configured as

an output, it will remain low or inactive. The configuration of P_BSY

(PP_BSY) as an output is suggested to avoid potential data loss. Reference

the parallel port timing section for detailed timing requirements for this mode.

4.3.1.3.2 Handshake with ACK: (BUSY_OP=0, ACK_OP=1)

Data transfers are acknowledged using P_ACK (PP_ACK). The position of

P_ACK (PP_ACK) relative to the trailing edge of data strobe is set using

DSS. Note that in this mode, the actual positioning of P_ACK (PP_ACK) will

be DSS plus 3 to 4 SBus clocks, due to synchronization delays. The width of

P_ACK (PP_ACK) is set using DSW. P_BSY (PP_BSY) will be generated

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

as required to gate further transfers but not as a handshake signal. The oper-

ation of the interface as defined assumes the bidirectional sense of each signal

has been configured as follows: DIR=1, DS_DSEL=1, ACK_DSEL=1,

BUSY_DSEL=1. The configuration of P_BSY (PP_BSY) as an output is

suggested to avoid potential data loss. Reference the data transfer diagram in

Figure 6.

P_DATA (I)

P_D_STRB

(I)

DSS

DSW

P_ACK (O)

1. Acknowledge position relative to data strobe (DSS - hardware configuration register).

2. Acknowledge width (DSW - hardware configuration register).

3. P_BSY will be asserted if required.

4. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 6.

4.3.1.3.3 Handshake with BUSY: (BUSY_OP=1, ACK_OP=0)

Data transfers are acknowledged using P_BSY (PP_BSY). P_BSY

(PP_BSY) will be generated off of the leading edge of P_D_STRB (PP_STB)

and will remain active for the period specified by DSS (plus 3 to 4 SBus

clocks) beyond the end of P_D_STRB (PP_STB). The operation of the inter-

face as defined assumes the bidirectional sense of each signal has been con-

figured as follows: DIR=1, DS_DSEL=1, ACK_DSEL=X,

BUSY_DSEL=1. The configuration of P_ACK as an input will not hinder the

operation of the interface as far as handshaking is concerned. If P_ACK is

configured as an output, it will remain low or inactive. Reference the data

transfer diagram Figure 7.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

P_DATA (I)

P_D_STRB

(I)

Logic 0

P_ACK (O)

DSS

1. P_BSY hold time after data strobe (DSS - hardware configuration register)

2. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 7.

4.3.1.3.4 Handshake with ACK and BUSY: (BUSY_OP=1, ACK_OP=1)

Both P_ACK (PP_ACK) and P_BSY (PP_BSY) are generated in response to

a data strobe. P_BSY (PP_BSY) will be generated off of the leading edge of

P_D_STRB (PP_STB) and will remain active for 3 SBus clocks beyond the

end of P_ACK (PP_ACK). The position of P_ACK (PP_ACK) relative to the

trailing edge of data strobe is defined by DSS (again DSS has a tolerance of

+3 to 4 SBus clocks). The width of P_ACK (PP_ACK) is set using DSW. The

operation of the interface as defined assumes the bidirectional sense of each

signal has been configured as follows: DIR=1, DS_DSEL=1,

ACK_DSEL=1, BUSY_DSEL=1. Reference the data transfer diagram in

Figure 8.

P_DATA (I)

P_D_STRB

(I)

DSS

DSW

P_ACK (O)

1. Acknowledge position relative to data strobe (DSS - hardware configuration register).

2. Acknowledge width (DSW - hardware configuration register).

3. P_BSY is deasserted 3 SBus clocks following the trailing edge of ACK.

4. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 8.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

4.3.1.4 Master Read/Write Protocol (Xerox Mode)

STP2002QFP

This section describes the parallel port operation while master read cycles are

performed. Operation while master write cycles are performed is the same as

is described in the “Unidirectional Operation (Transfers to the Peripheral De-

vice)” section on page 15.

Data transfer for master read cycles is accomplished by the master gener-

ating a data strobe (request for data) with no data present on the P_DATA

(PP_DATA) bus. The peripheral responds by placing data on the P_DATA

(PP_DATA) bus and generating an P_ACK (PP_ACK) which functions as a

strobe. Only one handshake protocol is valid for master read cycles and is

described below.

4.3.1.4.1 Handshake with ACK: (BUSY_OP=0, ACK_OP=1)

Data is transferred to the HIOD by the use of P_ACK (PP_ACK).

P_D_STRB (PP_STB) width is defined by DSW. DSS is used to define the

required interval from P_ACK (PP_ACK) to the next P_D_STRB (PP_STB).

P_BSY (PP_BSY) will gate further data transfers if present. The operation of

the interface as defined assumes the bidirectional sense of each signal has

been configured as follows: DIR=1, DS_DSEL=0, ACK_DSEL=0,

BUSY_DSEL=0. Reference the data transfer diagram in Figure 9.

P_DATA (I)

DSS

P_D_STRB

(O)

DSW

P_ACK (I)

1. Data strobe width as defined in the hardware configuration register.

2. DSS is used for ACK to P_D_STRB stiming (Hardware configuration register).

3. Acknowledge is used as a strobe and is required for each byte transferred.

4. If P_BSY is active, it gates further data transfers.

5. All signal polarities shown are at the HIOD pins. Polarities on the interface cable should be inverted (except P_DATA).

Figure 9.

4.3.2 Programmed I/O Mode

Programmed I/O mode is intended to allow the parallel port to operate prima-

rily under software control. Data latching, interrupt, and busy generation are

performed in hardware as required. The following two sections describe op-

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

eration for transfers to and from the peripheral device.

4.3.2.1 PIO on Transfers to the Peripheral Device

For transfers to the peripheral device, all signals are under the control of soft-

ware. There is no hardware assist other than interrupt generation.

4.3.2.2 PIO on Transfers From the Peripheral Device

The two modes of bidirectional operation previously discussed are supported

with hardware-assisted data latching. The bidirectional select bits

(DS_DSEL, ACK_DSEL, BUSY_DSEL) should be set according to the de-

sired configuration. The handshake protocol bits (ACK_OP, BUSY_OP)

have no function in PIO mode.

During operation as a slave under the master write protocol (DS_DSEL=1,

DIR=1), data is sampled and latched once data strobe has been detected.

P_BSY (PP_BSY) becomes active at the same time that data is latched and

must be made inactive under software control.

During operation under master read/write protocol (DS_DSEL=0,

DIR=1), master reads are assisted by sampling and latching the data once

P_ACK (PP_ACK) has been detected. P_BSY (PP_BSY) is not generated in

this mode.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

4.4 Differences from STP2000 (MACIO) Parallel Port

• PP_INIT and PP_AFXN have extra functions: high and low address

latch clocks

• EPROM address is given by parallel port data bus

• DIR bit in the TCR register must be set during memory clear operation

4.5 Test Support

The TST_CSR provides a way for the user to test the DMA engine. The test

consists of moving one block data of the size of a read burst from the host

memory into the FIFO. The user then instructs the engine to drain data back

to the host memory at an address which is programmable.

The maximum size of a read burst is 32 bytes. Since the starting address of

the FIFO register cannot be programmed, the user has no control over which

FIFO registers should be tested. And since the maximum size of the burst is

limited to 32 bytes, the entire FIFO (64 bytes) cannot be tested.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

ETHERNET CHANNEL

5.1 Introduction

The Ethernet channel is a dual-channel intelligent DMA controller on the sys-

tem side, and an IEEE 802.3 Media Access Control (MAC) on the network

side. It is designed as a high-performance full-duplex device, allowing for si-

multaneous transfers of data from/to host memory to/from the “wire.” The

two main functions of the Ethernet channel are to provide MAC function for

a 10-/100-Mbps CSMA/CD protocol based network and to provide a high-

performance two-channel DVMA host interface between the MAC controller

and the SBus. The Ethernet channel supports 10/100-Mbit Fast Ethernet. The

Fast Ethernet standard is backwards compatible with the standard 10-Mb/s

Ethernet standard. The speed is auto-sensed. An RJ-45 connector supports

twisted-pair style of Ethernet. In addition, a Media Independent Interface

(MII) connection is supported through an external transceiver to allow adap-

tation to any other form of Ethernet (AUI/TP/ThinNet).

5.2 Functional Description

5.2.1 Overview

Packets scheduled for transmission are transferred over the SBus into a local

transmit FIFO and are later transferred to the TX_MAC core for protocol pro-

cessing and transmission over the medium. A programmable transmit thresh-

old is provided to enable the transmission of the frame. The reverse process

takes place in the receive path. Packets received from the medium are pro-

cessed by the RX_MAC, loaded into the receive FIFO, and are later trans-

ferred to the host memory over the SBus. The receive threshold for data

transfers is 128 bytes.

At the device driver level, the user deals with transmit and receive descrip-

tor-ring data structures for posting packets and checking status. In the

transmit case, packets may be posted to the hardware in multiple buffers

(descriptors), and the transmit DMA engine will perform “data gather.” In the

receive case, the receive DMA engine will store an entire packet in each

buffer that was allocated by the host. “Data scatter” is not supported, but

instead a programmable first byte-alignment offset within a burst is

implemented.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

For TCP packets, hardware support is provided for TCP checksum compu-

tation. On transmit, it is assumed that the entire packet is loaded into the local

FIFO before its transmission begins. The checksum is computed on-the-fly

while the packet is being transferred from the host memory into the local

FIFO. The checksum result is then stuffed into the appropriate field in the

packet, and the transmission of the frame begins. On receive, checksum is

computed on the incoming data stream from the MAC core, and the result is

posted to the device driver as part of the packet status in the descriptor.

5.2.2 Functional Blocks

The Ethernet channel is comprised of five major blocks:

• BigMAC core

• Management interface (MIF)

• Ethernet transmit (ETX)

• Ethernet receive (ERX)

• Shared Ethernet block (SEB)

5.2.2.1 BigMAC Core

The BigMAC core implements the IEEE 802.3 MAC protocol for 10-/100-

Mbps CSMA/CD networks. It consists of four major functional modules:

• Host interface buffer

Implements the programmed I/O interface between the SEB and Big-

MAC core

• Transmit MAC (TX_MAC)

- Implements the IEEE 802.3 transmit portion of the protocol

- Implements the slave interface handshake between the ETX and

TX_MAC for frame data transfers

- Performs the synchronization between the system clock domain and

the transmit media clock domain in the transmit data path

• Receive MAC (RX_MAC)

- Implements the IEEE 802.3 receive portion of the protocol

- Implements the slave interface handshake between the ERX and

RX_MAC for frame data transfers

- Performs the synchronization between the system clock domain and

the receive media clock domain in the receive data path

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

• Transceiver interface (XIF)

- Implements the MII interface protocol (excluding the management

interface)

- Performs the nibble-to-byte and byte-to-nibble conversion between

the protocol engine and the MII

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

5.2.2.2 Management Interface Function (MIF)

STP2002QFP

The management interface block implements the management portion of the

MII interface to an external transceiver, as defined in the IEEE 802.3 MII

specification.

It allows the host to program and collect status information from two

external transceivers connected to the MII. The MIF supports three modes of

operation.

Bit-Bang Mode

The Bit-Bang mode of operation provides maximum flexibility with mini-

mum hardware support for the serial communication protocol between the

host and the transceivers. The actual protocol is implemented in software, and

the interaction with the hardware is done via three one-bit registers: data,

clock, and output_enable. Each read/write operation on a transceiver register

would require approximately 150 software instructions by the host.

Frame Mode

This mode of operation provides a much more efficient way of communica-

tion between the host and the transceivers. The serial communication proto-

col between the host and the transceivers is implemented in hardware, and the

interaction with the software is done via one 32-bit register (frame register).

When the software wants to execute a read/write operation on a transceiver

(frame), and poll the valid bit for completion. The hardware will detect the

instruction, serialize the data, execute the serial protocol on the MII manage-

ment interface and set the valid bit to the software.

Polling Mode

As defined in the IEEE 802.3u MII standard, a transceiver shall implement at

least one status register that will contain a defined set of essential information

needed for basic network management. Since the MII does not include an in-

terrupt line, a polling mechanism is required for detecting a status change in

the transceiver. In order to reduce the software overhead, the above men-

tioned polling mechanism has been implemented in hardware. When this

mode of operation is enabled, the MIF will continuously poll a specified

transceiver register, and generate a maskable interrupt when a status change

is detected. Upon detection of an interrupt, the software can read a local status

indication which bits have changed since it was last read. This mode of oper-

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

ation can only be used when the MIF is in the frame mode.

5.2.2.3 Ethernet Transmit Block (ETX)

The Ethernet transmit block provides the DMA engine for transferring frames

from the host memory to the BigMAC. It contains a local buffer of 2K bytes

for rate adaptation between the available bandwidth on the SBus and on the

network.

5.2.2.4 Ethernet Receive Block (ERX)

The Ethernet receive block provides the DMA engine for transferring frames

from the BigMAC to the host memory. It contains a local buffer of 2K bytes

for rate adaptation between the available bandwidth on the network and on

the SBus.

5.2.2.5 Shared Ethernet Block (SEB)

The shared Ethernet block contains common functions that are shared be-

tween the ETX and ERX blocks. It performs the first level arbitration be-

tween the receive and transmit DMA channels for access to the SBus and

provides one common interface between the Ethernet channel and the SBus

adapter (SBA). It also separates the DMA data path from the programmed I/O

data path.

5.2.3 Clock Domains

The Ethernet channel contains three completely asynchronous clock do-

mains.

System Clock Domain

The bulk of the logic in the Ethernet channel is driven off this clock. It is

sourced by the system bus and is defined to be in the range of 16.67 MHz

through 33.33 MHz.

Transmit Clock Domain

This clock is used to drive the transmit protocol engine in the BigMAC core.

It is sourced by the MII and has the operating frequency of 2.5/25 MHz 100

ppm. The 2.5/25 MHz version of this clock (TX_NCLK) is used for byte-to-

nibble conversion of the data stream to the MII and for synchronization of the

asynchronous signals from the MII (CRS and COLL). The 1.25/12.5 MHz di-

vide-by-two version of this clock (TX_BCLK) is used for transmit protocol

processing and state machine operation.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Receive Clock Domain

This clock is used to drive the receive protocol engine in the BigMAC core.

It is sourced by the MII and has the operating frequency of 2.5/25 MHz 100

ppm. The 2.5/25 MHz version of this clock (RX_NCLK) is used for strobing

in the packet data from the MII and for nibble-to-byte conversion of the in-

coming data stream. The 1.25/12.5 MHz divide-by-two version of this clock

(RX_BCLK) is used for receive protocol processing and state machine oper-

ation.

5.2.4 Host Memory Data Management

The device driver maintains two data structures in the host memory: one for

transmit and the other for receive packets. Both data structures are organized

as wrap-around descriptor rings. Each descriptor ring has a programmable

number of descriptors (in the range of 16 through 256). Each descriptor has

two entries (words): a control/status word and a pointer to a data buffer.

The interaction between the hardware and the software is managed via a

semaphore (OWN) bit, that resides in the control/status portion of the descrip-

tor. When the OWN bit is set to 1, the descriptor is owned by the hardware.

If the OWN bit is cleared to 0, the descriptor is owned by the software. The

owner of the descriptor is responsible for releasing the ownership when it can

no longer use it. Once the ownership is released, the previous owner may no

longer treat the descriptor contents as valid, since the new owner may over-

write it at any time.

5.2.5 Transmit Data Descriptor Ring

A transmit packet that is posted by an upper layer protocol to the device driver

may reside in several data buffers (headers and data) which are scattered in

the host memory. When the device driver posts the packet to the hardware, it

allocates a descriptor for each buffer. The descriptor contains the necessary

information about the buffer that the hardware needs for the packet transfer.

When the packet is ready for transmission, the descriptor(s) ownership is

turned over to the hardware, and a programmed I/O command is issued to the

transmit DMA channel to start the packet transfer from the host memory to

the TxFIFO.

When the packet transfer has been completed, the transmit DMA channel

turns over the descriptor ownership back to the driver and polls the next

descriptor in the ring. If the descriptor is owned by the hardware, the next

packet transfer begins. If not, the DMA channel “goes to sleep” until a new

command is issued.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

The size of the descriptor ring is programmable, and it can be varied in the

range of 16–256 in increments of 16 descriptors: 16, 32, 48, ..., 240, 256.

5.2.6 Receive Free Buffer Descriptor Ring

For receive operation, the device driver requests a pool of free buffers from

the operating system. The buffers are posted to the hardware by allocating a

descriptor for each buffer. The descriptor contains the necessary information

about the buffer that the hardware needs for the packet transfer.

When a packet is ready to be transferred from the RxFIFO to the host mem-

ory, the receive DMA channel polls the next descriptor in the ring. If the

hardware owns the descriptor (free buffer available), the packet transfer

begins. During the first burst, the receive DMA engine performs header pad-

ding of the packet by inserting a programmable number of junk words at the

beginning of the packet.

When the packet transfer has been completed, the receive DMA channel

updates the descriptor with status information about the received packet, and

turns over the descriptor ownership back to the driver. If a packet is ready to

be transferred from the RxFIFO to the host memory but the driver does not

have any free buffers allocated to the hardware, the packet will be dropped

into the bit bucket, and the DMA channel will try again when the next packet

is ready to go.

The size of the descriptor ring is programmable and can assume the follow-

ing values: 32, 64, 128, 256.

5.2.7 Local Memory Data Management

Each DMA channel contains its own dedicated on-chip local buffer of 2K

bytes (fixed) in size. The local buffers are used for temporary storage of pack-

ets en route to/from the network, and are organized as wrap-around FIFOs.

In general, the local buffer organization and data structures are invisible to

the software, except for diagnostic purposes.

Since the local buffers reside in the data path, their logical organization

changes depending on the SBus width. For a 32-bit SBus, the FIFO organiza-

tion is 512 words × 33 bits. For a 64-bit SBus, the FIFOs are organized as 256

words × 65 bits. The extra bits (bit 33 or bit 65) along the word are used as

end-of-packet delimiters (or tags). When a packet is stored in the local buffer,

the tag will be cleared to 0 for the entire data portion of the packet, except for

the last word. The tag will be set to 1 for the last data word of the packet and

for the control/status word.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.2.8 Transmit FIFO Data Structures

When a transmit packet is transferred from the host into the local memory, the

first byte of the packet in the FIFO is always loaded to be word (or double-

word) aligned. If the packet is composed of several data buffers, the data buff-

ers are concatenated as a contiguous byte stream in the FIFO (gather func-

tion). The last byte of a packet can reside at any byte boundary, therefore the

last data word of the packet is marked by a tag. At the end of the packet a con-

trol word is appended, which is again marked by a tag bit. The control word

indicates the last byte boundary for the packet.

5.2.9 Receive FIFO Data Structures

When a receive packet is transferred from the RX_MAC into the local mem-

ory, the half-word (16-bit) data stream is packed into words (or double

words), with the first byte of the packet starting at a programmable offset

within the first word.

Even though the receive data structure’s functionality does not require to

tag the last data word of a packet, the hardware will do that to provide a more

robust implementation.

At the end of the packet a status word is appended, which is again marked

by a tag bit. This word provides status information about the received frame,

which is either passed to the device driver or used for unloading the frame

from the RxFIFO.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.3 Error Conditions and Recovery

There are two types of error conditions that can be encountered during the

normal operation of the Ethernet channel: fatal errors and non-fatal errors. Fa-

tal errors are errors that should never occur. They usually indicate a serious

failure of the hardware or a serious programming error. When this type of er-

ror occurs, the recovery process is non-graceful. The corresponding DMA

channel will freeze, and the software is expected to reset the channel after the

appropriate actions are taken to correct the failure. Fatal error events are al-

ways reported to the software via an interrupt. Non-fatal errors are errors that

are expected to occur when certain conditions occur on the network or in the

system. When this type of error occurs, a graceful recovery mechanism is pro-

vided via a combination of hardware and software, as described below. Non-

fatal errors may or may not be reported to the software.

5.3.1 Fatal Errors

The error conditions described below can occur both in the transmit and in the

receive DMA channels.

Master_Error_Ack

This error condition indicates that an SB_ERR_ACK was detected by the

DMA channel during a DVMA cycle.

Slave_Error_Ack

This error condition indicates that an SB_ERR_ACK was generated by the

DMA channel during a programmed I/O cycle. The hardware will generate

an SB_ERR_ACK if a programmed I/O cycle is executed with SB_SIZE oth-

er than a word transfer.

Late_Error

This error condition indicates that an SB_LATE_ERROR was detected by the

DMA channel during a DVMA cycle.

DMA_Read_Parity_Error

This error condition indicates that a parity error was detected by the DMA

channel during a DVMA read cycle.

Slave_Write_Parity_Error

This error condition indicates that a parity error was detected by the DMA

channel during a

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

programmed I/O write cycle.

FIFO_Tag_Error

The data structures in the local FIFOs make use of tag bits for delimiting

packet boundaries. The last data word and the control/status word of a frame

are expected to have their tag bits set to 1. If the unload control state machine

does not see two consecutive tag bits set to 1, a local memory failure is rec-

ognized, and the unloading process is aborted.

5.3.2 Non-Fatal Errors

The error conditions described below can occur in the specified DMA chan-

nel only.

Tx_FIFO_Underrun

This error condition can occur only when the programmable threshold is used

to enable transmission of the frame by the TX_MAC (the threshold value is

less than the maximum frame size). If the available bandwidth on the SBus

dedicated to transmit DMA is less than the available throughput on the net-

work, the TxFIFO may run out of data before the frame transmission has

completed. The TX_MAC may become “starved” for data, and the frame

transmission is aborted. The unloading of the frame from the FIFO will con-

tinue until the entire frame is transferred to the TX_MAC, but the TX_MAC

will drop the remainder of the frame into the bit bucket. The TX_MAC will

generate an interrupt to the device driver to indicate the occurrence of this

event.

Rx_Abort (Early and Late)

A receive frame can be aborted for various reasons at any time during the

frame transfer from the network to the host memory. The intent of the provid-

ed abort mechanism is to utilize the available hardware resources efficiently,

without incurring unnecessary performance penalties.

If an abort condition is detected before the frame transfer has begun from

the RX_MAC into the RxFIFO (address detection criteria, short fragment,

etc.), the RX_MAC drops the frame and the receive DMA channel never sees

it.

If an abort condition occurred after the frame transfer from the RX_MAC

into the RxFIFO has begun, but before at least 128 bytes of data were trans-

ferred from the RX_MAC to the RxFIFO (long fragment, etc.), the load

control state machine rewinds the write pointer to the shadow write pointer

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

and gets ready to receive the next frame. This way the FIFO locations that

were occupied by the long fragment are reused by the next frame.

If an abort condition is detected after at least 128 bytes of data were trans-

ferred from the RX_MAC to the RxFIFO (very long fragment, CRC error,

code error on the media, etc.), the load control state machine sets the abort bit

in the status word that is appended to the frame and gets ready to receive the

next frame. When the aborted frame is unloaded from the RxFIFO, the unload

control state machine detects the abort bit in the status word and reuses the

current descriptor (host data buffer) for the next frame.

This error condition is not reported to the software, but the events causing

it have their individual reporting mechanisms.

Rx_FIFO_Overflow

If the available bandwidth on the SBus dedicated to receive DMA is less than

the available throughput on the network, the RxFIFO may run out of space

and not be able to receive any more data from the RX_MAC. This condition

propagates to the RX_MAC, and when it runs out of space in its synchroni-

zation FIFO the frame is aborted using the Rx_ABORT mechanism that was

described above.

The RX_MAC will continue to receive the frame from the network, but the

remainder of the frame is dropped “on the floor.” The RX_MAC will gener-

ate an interrupt to the device driver to indicate the occurrence of this event.

Rx_Buffer_Not_Available

When a receive frame is ready to be transferred to the host memory, the DMA

control state machine fetches the next descriptor from the ring. If the descrip-

tor is not owned by the hardware, the error condition is encountered. The un-

loading process unloads the frame from the RxFIFO and drops it “on the

floor.” When the next frame in the FIFO is to be unloaded, the DMA control

state machine polls the descriptor again. An interrupt is generated to the de-

vice driver to indicate the occurrence of this event.

Rx_Buffer_Overflow

The unloading process transfers frames from the RxFIFO to data buffers in

the host memory. If the size of a buffer in the host memory is smaller than the

frame size, the buffer is filled up and the remainder of the frame is dropped

“on the floor.” This error condition is not reported to the software via an in-

terrupt. Instead, when the descriptor is returned to the device driver, an over-

flow status bit is set in the descriptor. Also, the length field in the descriptor

specifies the actual size of the frame received.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.4 Programmer’s Reference

5.4.1 Overview

During normal operation, the software-to-hardware interaction is primarily

performed via the host memory data structures, with a minimal command/sta-

tus handshake (less than one interrupt per packet). Software intervention is re-

quired for initialization of the hardware after resetting the channel, for

network management, for error recovery, and for diagnostic purposes. Local

FIFOs’ data structures and most of the registers are invisible to the software,

except for diagnostic purposes.

5.4.2 Host Memory Data Structures

The host memory data structures are organized as wrap-around descriptor

rings of programmable size. The transmit and receive data structures are very

similar, except for three major differences:

1. Descriptor layout

2. Number of descriptors per packet: one for receive, unlimited for

transmit

3. Data buffer alignment restrictions: none for transmit, one for

receive

Programming Note: The pointers to descriptor ring base addresses

must be 2K-byte aligned.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.4.3 Transmit Data Structures

Table 10: Transmit Data Structure Descriptor Layout: Control Word

Field

Data buffer size

Bits

Description

13:0

Indicates the number of data bytes in the buffer.

All values are legal in a 16-KB range, including

Checksum start offset

Checksum stuff offset

19:14

27:20

Indicates the number of bytes from the ﬁrst byte

of the packet that should be skipped before the

TCP checksum calculation begins. This ﬁeld is

only meaningful if the Checksum Enable bit is

set to 1

Indicates the byte number from the ﬁrst byte of

the packet that will contain the ﬁrst byte of the

computed TCP checksum. This ﬁeld is only

meaningful if the checksum enable bit is set to 1

Checksum enable

End of packet

If set to 1, the computed TCP checksum will be

stuffed into the packet

When set to 1, indicates the last descriptor of a

transmit packet

Start of packet

When set to 1, indicates the ﬁrst descriptor of a

transmit packet

Ownership semaphore

To turn over ownership, the hardware clears this

bit, and the software sets it

Table 11: Transmit Data Structures: Descriptor Layout: Data Buffer

Pointer

Field

Bits

Description

Data buffer pointer

31:0

This 32-bit pointer indicates the ﬁrst data byte of the

transmit buffer

Programming Restrictions:

• If a packet occupies more than one descriptor, the software must turn

over the ownership of the descriptors to the hardware last-to-ﬁrst, in

order to avoid race conditions.

• If a packet resides in more than one buffer, the Checksum_Enable,

Checksum_Stuff_Offset and Checksum_Start_Offset ﬁelds must have

the same values in all the descriptors that were allocated to the packet.

• The hardware implementation relies on the fact, that if a buffer starts

at an odd byte boundary, the DMA state machine can rewind to the

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

nearest burst boundary and execute a full DVMA burst read.

Descriptor

Control Word

Data Buffer Pointer

Packet #1

Control Word

Data Buffer Pointer

Control Word

Data Buffer Pointer

Control Word

Data Buffer Pointer

Control Word

Data Buffer Pointer

#n+1

#n+2

#n+3

Packet #2

Packet #3

Last Descriptor

Control Word

Data Buffer Pointer

31 30 29 28 27

CHK

20 19

14 13

OWN

EOP

Checksum_Stuff_Offse Checksum_Start_Offse

Tx_Data_Buffer_Size

Enable

SOP

Tx_Data_Buffer_Pointer

Figure 10. Transmit Host Data Structures

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.4.4 Receive Data Structures

Table 12: Receive Data Structures Descriptor Layout: Status Word

Field

TCP checksum

Bits

Description

15:0

This ﬁeld contains the 16-bit TCP checksum

that was calculated on the entire frame. It will

be updated for every frame that was received

from the network. The software has the choice

of either making use of it or ignoring it.

Free_buffer/Packet_data size

29:16

When the descriptor ownership is passed from

the software to the hardware, this ﬁeld con-

tains the size of the free buffer that was

allocated for the packet. When the descriptor

ownership is passed from the hardware to the

software, this ﬁeld indicates the actual number

of packet data bytes that were dumped into the

buffer.

Overﬂow

When an Rx_Buffer_Overﬂow condition

occurs, this bit will be set to 1 for the frame

that could not ﬁt into the allocated buffer.

Ownership semaphore

End of packet

To turn over ownership, the hardware clears

this bit and the software sets it.

When set to 1, indicates the last descriptor of

a transmit packet.

Start of packet

When set to 1, indicates the ﬁrst descriptor of

a transmit packet.

Ownership semaphore

To turn over ownership, the hardware clears

this bit and the software sets it.

Table 13: Receive Data Structures: Descriptor Layout: Free Buffer Pointer

Field

Bits

Description

Free buffer pointer

31:2

This 29-bit pointer, points to the beginning of the free

buffer. The ﬁrst byte of the actual packet data inside the

buffer will always reside at a programmable offset from

this location, but within a double-word range.

Programming Restrictions:

• Free receive data buffers must be 64-byte aligned.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

5.4.5 Local Memory Data Structures

The local memory data structures are organized as wrap-around FIFOs that

can store an unlimited number of packets. The transmit and receive data

structures are very similar, except for the format of the control/status word

that is appended to the end of a packet and the alignment of the first byte of a

packet when it is loaded into the FIFO. Also, the RxFIFO does not have a

shadow read pointer. The logical organization of the FIFOs changes depend-

ing on the SBus configuration. For a 32-bit SBus, the FIFO organization is

512 words × 33 bits. For a 64-bit SBus, the FIFOs are organized as 256 words

× 65 bits. The 512 words × 33 bits configuration makes use of both the Tag_0

and the Tag_1 bits in the FIFO, while the 256 words × 65 bits configuration

uses only the Tag_0 bit.

On the diagrams shown below, frames #1 and #2 represent a 512 words ×

33 bits configuration, and frame #n represents a 256 words × 65 bits config-

uration. In reality, of course, only one configuration is used at a given time.

The configuration is selected by programming the extended transfer mode bit

in global configuration register. The amount of “junk” at the beginning of a

frame in the RxFIFO is determined by the first_byte_offset field in the ERX

configuration register.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Descriptor

Status Word

Free Buffer Pointer

Status Word

Packet #1

Packet #2

Free Buffer Pointer

Descriptor

Status Word

Free Buffer Pointer

Packet #n

Status Word

Free Buffer Pointer

Last Descriptor

31 30 29

16 15

Over-

OWN

Free_Buffer/Packet_Data Size

TCP_Checksum

Flow

Free Buffer Pointer

Reserved

Figure 11. Receive Host Data Structure

The software has the capability to read and write the FIFOs (including

tags) at any time, using programmed I/O instructions. This feature should be

used for diagnostic purposes only. During normal operation, the FIFOs are

invisible to the software.

5.4.6 TxFIFO Data Structures

Table 14: TxFIFO Data Structures: Control Word Layout

Field

Bits

Description

Last byte boundary

2:0 This ﬁeld indicates the offset of the last byte of the packet

within the last data word (or double word), depending on the

conﬁguration, in the FIFO

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Figure 12 below shows the organization of the TxFIFO. The first byte of

the frame is always loaded to be word or double-word aligned.

5.4.7 RxFIFO Data Structures

Table 15: RxFIFO Data Structures: Status Word Layout

Field

Bits

Description

Frame checksum

15:0

This ﬁeld contains the 16-bit TCP checksum for the

frame, as computed during the frame transfer from the

Rx_MAC to the RxFIFO.

Frame size

26:16

This ﬁeld indicates the size of the frame in bytes as cal-

culated by the Rx_MAC

Reserved

Receive abort

This bit communicates the occurrence of a late abort

event to the unload control state machine. The frame

should be dropped and the descriptor reused for the next

frame.

Figure 13 below shows the organization of the RxFIFO. The first byte of

the frame is always loaded at a programmable offset within the first word or

double word.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Tag_0

Tag_1

Addr_0

Frame #1 Data

Shadow

Read_Ptr

32-Bit

Mode

junk

Frame #1 Control

Frame #2 Data

junk

Frame #2 Data

Read_Ptr

Frame #2 Control

Wrap-

Around

FIFO

Frame #3 Data

Shadow

Write_Ptr

Frame #n Data

64-Bit

Mode

Write_Ptr

Addr 255

junk

Frame #n Control

junk

Frame #n Control

Tag_0/Tag_1

Byte

Boundary

Frame Control

Word

Reserved

Figure 12. TxFIFO Organization

5.4.8 Other User Accessible Resources

Besides the host and local memory data structures, the hardware provides a

programmed I/O path to a variety of hardware resources for initialization, er-

ror recovery, diagnostics, and network management. From the software per-

spective, all the programmable resources should be treated as 32-bit entities.

If not all 32 bits are used in a register, the unused bits are grouped as the most

significant bits of the word. Register fields that are not used are ignored dur-

ing a PIO write, and return 0s during a PIO read. The description of these re-

sources is grouped by functionality and not necessarily by their physical

location. The default value for all the registers/counters is 0x00000000, un-

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

less specified otherwise.

Tag_0

Tag_1

Addr_0

junk

Frame #1 Data

32-Bit

Mode

junk

Frame #1 Control

Frame #2 Data

junk

Frame #2 Data

Read_Ptr

Frame #2 Control

junk

Wrap-

Around

FIFO

Frame #3 Data

Shadow

Write_Ptr

junk

Frame #n Data

64-Bit

Mode

Write_Ptr

Addr 255

junk

Frame #n Control

junk

Frame #n Control

Tag_0/Tag_1

31 30

Rx_

Abort

1615

Frame Status

Word

Frame Checksum

Rsrvd

Frame Size

Figure 13. RxFIFO Organization

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

TESTABILITY

6.1 Introduction

This section describes the features of the JTAG Test Access Port (TAP) and

other testability structures for the FEPS. The JTAG macro which implements

the IEEE Standard 1149.1-1990 provides access to the test structures on the

chip.

The TAP includes the TAP controller state machine, an instruction regis-

ter, a bypass register, a device identification register, and the necessary

decoding logic. The TAP requires five dedicated pads: test data input (TDI),

test data output (TDO), test mode select (TMS), test clock (TCK), and test

reset (TRST).

6.2 JTAG Macro

ISCAN_MODE

JTAG_TDO_EN

BSCAN_CDR

BSCAN_SDI

BSCAN_SDR

BSCAN_UDR

BSCAN_IMC

BSCAN_OMC

JTAG_TDO

JTAG_TCK

JTAG_TMS

JTAG_TDI

JTAG_CONTR

JTAG_TRST

BSCAN_TDO

ISCAN_SO

ISCAN_CLK

ISCAN_SDR

SCSI_SELECT

ISCAN_SDI

Figure 14.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 16: JTAG Macro I/O Signals

JTAG_TCK

JTAG clock from chip pads

JTAG_TDI

JTAG test data in from chip pads

JTAG test data out to chip pads

JTAG test reset from chip pads

JTAG mode select from chip pads

JTAG test data out enable to chip pads

Boundary scan clock data register

Boundary scan data input (to BSCAN cells)

Boundary scan shift data register

Boundary scan update data register

Boundary scan input mode control

Boundary scan output mode control

Boundary scan test data output

Internal scan clock

JTAG_TDO

JTAG_TRST

JTAG_TMS

JTAG_TDO_EN

BSCAN_CDR

BSCAN_SDI

BSCAN SDR

BSCAN_UDR

BSCAN_IMC

BSCAN_OMC

BSCAN_TDO

ISCAN_CLK

ISCAN_SDR

ISCAN_SDI

ISCAN_TDO

SCSI_SELECT

ISCAN_MODE

Internal shift select

Internal scan data input

Internal scan test data output

SCSI test mode select signal

Internal scan mode select signal

The above signals describe the I/O signals of the JTAG macro. The JTAG

macro is composed of the following blocks: TAP controller, instruction reg-

ister, instruction decode logic, bypass register, internal register clocking

logic, JTAG ID register, JTAG boundary scan control logic, and the TDO

MUX logic.

The following sections describe each of these blocks.

6.2.1 TAP Controller

The TAP controller is a 16-state finite state machine. Transitions between

states occur synchronously at the rising edge of JTAG_TCK in response to

the JTAG_TMS signal or when JTAG_TRST goes low.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

DR_CLOCK

DR_UPDATE

DR_SHIFT

JTAG_TCK

JTAG_TMS

JTAG_TRST

IR_CLOCK

IR_SHIFT

JTAG_TAP

JTAG_TDO_EN

REG_SEL

TAP_RESET

DR_CAPTURE

IR_UPDATE

Figure 15.

6.2.2 Instruction Register

The instruction register is used to select the test to be performed and/or the

test data register to be accessed. The FEPS instruction register is four bits

wide and is a shift register with parallel load and parallel outputs. At the start

of an instruction register shift cycle (during the CAPTURE-IR state), the least

two significant bits are loaded with 01 pattern. During the TEST-LOGIC-RE-

SET controller state the instruction register must have the IDCODE. The in-

struction register state is updated at the falling edge of the JTAG_TCK. The

shifting of the instruction register occurs at each rising edge of JTAG_TCK.

IR-CLOCK

IR_TDO

IR_SHIFT

JTAG_TDI

IR_UPDATE

TAP_RESET

JTAG_JR

IR_VALUE[3:0]

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Figure 16.

The following instructions are supported in the FEPS.

Table 17: FEPS-Supported Instructions

Value

0000

0001

0010

0011

0100

0101

0110

0111

1000

1001

1010

1011

1100

1101

1110

1111

Instruction

Extest

Scan Chain

Boundary

Internal

ATPG

IMC

OMC

BCAP

ICAP

Sample

Intscan

ATPG

Debug

Internal

Bypass

Boundary

Bypass

CCR

Reserved

Clamp

Intest

Reserved

SCSI_TEST

Reserved

SEL_CCR

Reserved

IDCODE

Bypass

• IMC1 = core driven by boundary scan (BS) cell, 0 = core driven by pin

• OMC1 = pin driven by BS cell, 0 = pin driven by core

• BCAP1 = capture clock generated for BS cell, 0 = no clock

• ICAP1 = capture clock generated for internal ﬂops, 0 = no clock

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

6.2.3 Instruction Decode Logic

BYPASS_SELECT

ID_SELECT

ISCAN_MODE

ATPG_SELECT

IR_VALUE[3:0]

INTERNAL_SELEC

JTAG_DECODE

DEBUG_SELECT

BSCAN_SELECT

SCSI_SELECT

CCR_SELECT

BSCAN_OMC

Figure 17.

The instruction decode logic decodes the value at the parallel outputs of the

instruction register and selects the appropriate scan data register and control

signals.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

TDI

MUX

ATPG_MODE

Boundary Scan Register

Internal Scan Register

BSCAN_CDR

ISCAN_CLK

IR_CLOCK

JTAG Instruction Register

JTAG ID Register

MUX

DR_CLOCK

Bypass Register

Clock Control Register

Test Mode Selects

Figure 18.

6.2.4 Bypass Register

The bypass register provides a minimum length path between the test data in-

put and the test data output. It consists of a single shift-register stage that

loads a constant 0 in the Capture-DR TAP controller state when the manda-

tory BYPASS instruction is selected.

JTAG_TDI

DR_CLOCK

JTAG_BYPASS

DR_SHIFT

BYPASS_TDO

BYPASS_SELEC

Figure 19.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

6.2.5 Internal Register Clocking Logic

This module generates the scan clock for the internal scan flops and the scan

enable to for the scan flops.

ISCAN_MODE

ISCAN_DR

DEBUG_SELEC

IS_CLOCK

DR_CLOCK

DR_CAPTURE

ISCAN_CLK

DR_SHIFT

Figure 20.

6.2.6 JTAG ID Register

This is a 32-bit shift register which has four fields. The least significant bit is

a 1, the next 11 bits [11:1] are the manufacturer’s ID, the next 16 bits [27:12]

are the chip ID, and the most significant 4 bits [31:28] are the chip vintage.

The JTAG ID for FEPS Rev 1.0 is 01792045 hex, for FEPS Rev 2.0 and 2.1

it is 11792045 hex, and for FEPS Rev 2.2 it is 21792045 hex.

JTAG_TDI

DR_CLOCK

ID_TDO

JTAG_ID

DR_SHIFT

ID_SELECT

Figure 21.

6.2.7 Boundary Scan Control Logic

This block generates the boundary scan clock and the boundary scan shift and

update signals which form part of the boundary scan control bus that runs

along the boundary scan chain. This control bus feeds the boundary scan

cells.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

DR_CLOCK

BSCAN_CDR

DR_UPDATE

JTAG_BS

BSCAN_UDR

DR_SHIFT

BSCAN_SELECT

BSCAN_SDR

Figure 22.

6.2.8 TDO MUX logic

This block implements the muxing of the signal which is to appear at the TDO

output pin. It has one flop to ensure that changes on the TDO pin happen on

the falling edge of JTAG_TCK when the data is not being shifted in the data

registers. When data is not being shifted through the chip, TDO is set to a

high-impedance state.

BYPASS_TDO

ISCAN_TDO

BSCAN_TDO

ID_TDO

JTAG_TDO

IR_TDO

CCR_TDO

BYPASS_SELECT

JTAG_TDO_M

CCR_SELECT

ID_SELECT

BSCAN_SDI

ATPG_SELECT

ISCAN_MODE

REG_SEL

JTAG_TCK

BSCAN_SELECT

JTAG_TDI

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Figure 23.

6.3 Special JTAG Instructions

In addition to the mandatory instructions, the FEPS JTAG implements some

special instructions.

6.3.1 Debug Modes

6.3.1.1 Dumping Internal State

Using the DEBUG instruction, the internal chain can be selected. This in-

struction provides nondestructive internal node visibility during lab debug.

No capture clock is issued for this instruction. While the debug instruction is

selected, both the inputs and outputs are defined by the contents of the bound-

ary scan register.

6.3.1.2 Clock Controller

The clock controller will deterministically stop FEPS internal clocks upon the

occurrence of an external event. The clock controller can only be accessed via

the CCR scan chain. This chain is selected via the SEL_CCR instruction.

The clock controller consists of a stop enable bit and three synchronizers

for the SBus, ENET-Tx, and ENET-Rx domains. When the stop bit is set, the

clock_stop signal will switch the source of the internal clock from the clock

pins to the internal controller. This clock source switching is synchronized to

the rising edge for each clock domain.

6.3.2 INTEST

INTEST can be used to apply stimulus to test the on-chip logic when the chip

sits on a board. This requires that the core be driven off the input boundary-

scan cells and the core drives the output boundary-scan cells. For this we re-

quire that the clock pads be made controllable via boundary scan. INTEST

can also be used to apply burn-in vectors if the burn-in tester is pin limited

and can’t accommodate all the FEPS pins.

6.3.3 SCSI Test Mode

The SCSI Test mode will provide access to the I/O signals of the SCSI

FAS366 core through the I/O pins. This mode isolates the SCSI core by pro-

viding controllability and observability to its I/O signals. The vectors applied

will yield 95% coverage in the SCSI core area which does not have internal

scan.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

6.4 Clock Stop Pin

This pin can deterministically stop the clocks in FEPS. After the instruction

loaded into the CCR scan data register. In the run-test/idle state, any external

event which triggers the clock stop pin will switch the clock source from the

clock pins to the ISCAN_CLK signal generated by the JTAG logic. This sig-

nal is held high in the run-test/idle controller state. The switching is synchro-

nized with the rising edge of the clocks of the respective clock domains.

The clocks that need to be stopped are those that are those that control the

flops in the full scan area which are the SBus, ENET-Tx, and ENET-Rx

clocks.

Int_Scan_Enable shifts the clock between the SBus_CLK and the

ISCAN_CLK. This clock tree feeds the scan flops in the SBA, parallel port,

and SCSI DMA where the scan flops have the same system and scan clock.

ENET_Tx_Scan_En is the clock enable for the scan flops in the Ethernet

Tx clock domain. Here the scan flops have TX_CLK as the system clock and

a SBUS_CLK as the scan clock. ENET_Rx_Scan_En is the clock enable for

the scan flops in the Ethernet Rx clock domain. Here the scan flops have

RX_CLK as the system clock and a SBUS_CLK as the scan clock.

6.5 Test Vectors

The RAMs and data buffers are tested using high-coverage functional vectors

which target memory-specific faults. The full scan area is tested by combina-

tional ATPG vectors which yield a high fault coverage.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

PROGRAMMING MODEL

7.1 Introduction

Refer to the FEPS application note (STB0106) for programming notes and a

complete address map for the registers for all interfaces.

7.2 Parallel Port Channel Registers

7.2.1 Control/Status Register

Table 18: Control/Status Register Address

Physical Address

Access Size

Control/Status register (P_CSR)

0xC80_0000

4 bytes

Table 19: Control/Status Register Deﬁnition

Field

Bits

Description

Type

P_INT_PEND

Set when a PP DMA or PP control interrupt is pending or when P_TC is set

and P_TCI_DIS is not set.

P_ERR_PEND

P_DRAINING

Set when an interrupt is pending due to an SBus error condition.

3:2

Both bits set when the P_FIFO is draining to memory, otherwise both bits are

P_INT_EN

When set, enables SB_P_IRQ to become active when either P_INT_PEND or

P_ERR_PEND is set.

R/W

P_INVALIDATE

P_SLAVE_ERR

When set, invalidates the P_FIFO. Resets itself. Reads as 0.

Set on slave access size error to a PP register. Reset by P_RESET,

P_INVALIDATE, or writing to 1.

R/W

P_RESET

P_WRITE

P_EN_DMA

When set, acts as a hardware reset to the parallel port only.

DMA direction. 1 = to memory; 0 = from memory

When set, enables DMA transfers to/from the PP.

R/W

12:10

P_EN_CNT

P_TC

When set, enables the PP byte counter to be decremented

R/W

Terminal count. Set when byte count expires. Reset on write of 1 if

P_EN_NEXT=1.

REV_MIN [2:0]

P_BURST_SIZE

P_DIAG

17:15

19:18

FEPS minor revision number

Deﬁnes sizes of SBus read and write bursts for PP transfers.

R/W

When set, disables draining and resetting of P_FIFO on loading of P_ADDR

22:21

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 19: Control/Status Register Deﬁnition

Field

P_TCI_DIS

P_EN_NEXT

Bits

Description

Type

When set, disables P_TC from generating an interrupt.

R/W

When set, enables DMA chaining and next address/byte count auto-load

mechanism. P_EN_CNT must also be set.

R/W

P_DMA_ON

DMA On. When set, indicates that DMA transfers are not disabled due to any

hardware or software condition.

P_A_LOADED

Set when the contents of the address and byte count are considered valid dur-

ing chained transfers.

P_NA_LOADED

REV_MAJ [3:0]

Set when next address and byte count registers have been written but have not

been used for chaining.

31:28

FEPS major revision number

The RESET state of this register is as follows:

P_ERR_PEND = 0

P_INVALIDATE = 0

P_RESET = 0

P_INT_EN = 0

P_SLAVE_ERR = 0

P_EN_DMA = 0

P_TC = 0

P_EN_CNT = 0

P_BURST_SIZE = 0

P_EN_NEXT = 0

P_A_LOADED = 0

P_WRITE = 1

P_TCI_DIS = 0

P_DMA_ON = 0

P_NA_LOADED = 0

P_INT_PEND:

Interrupt pending is the logical OR of the following enabled PP interrupt

sources:

(P_TC and !P_TCI_DIS), DS_IRQ, ACK_IRQ, BUSY_IRQ, ERR_IRQ,

PE_IRQ, SLCT_IRQ.

P_ERR_PEND:

Error pending will be set due to an SBus error acknowledge or an SBus late

error. It indicates an SBus error condition. PP DMA is stopped

(P_DMA_ON=0) when this bit is set. This bit can be reset by setting

P_INVALIDATE or P_RESET.

P_DRAINING:

When P_FIFO is draining to memory, both bits are set. Do not assert

P_RESET or P_INVALIDATE or write to the P_ADDR register when set.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

P_DRAINING bits are not valid while P_ERR_PEND is set and should be ig-

nored.

P_INVALIDATE:

Setting this bit invalidates the P_FIFO. If P_ERR_PEND = 0 when

P_INVALIDATE is set, all dirty data in the P_FIFO will first be drained to

memory. If P_ERR_PEND = 1 when P_INVALIDATE is set, all dirty data

in the P_FIFO will be discarded. In addition to invalidating the P_FIFO, set-

ting this bit causes P_ERR_PEND and P_TC to be reset. If P_EN_NEXT =

1, P_A_LOADED, and P_NA_LOADED will also be reset.

P_RESET:

This bit functions as a hardware reset to the parallel port. It will remain active

once written to one until written to zero, unless cleared by an SBus reset

(SB_RESET asserted). Setting P_RESET or asserting SB_RESET will inval-

idate the P_FIFO and reset all parallel port interface state machines to their

idle states. If P_ERR_PEND = 0 when P_RESET is set, all dirty data in the

P_FIFO will first be drained to memory. When this occurs, P_RESET must

not be cleared until draining is complete, as indicated by P_DRAINING = 00.

If P_ERR_PEND = 1 when P_RESET is set, no draining will take place and

all dirty data in the P_FIFO will be discarded.

P_WRITE:

This read only bit reflects the direction for DMA transfers. It is a logical OR

of the DIR bit of the parallel control register (P_TCR) and the MEM_CLR bit

of the parallel operation control register (P_OCR).

P_EN_DMA:

When set, enables DMA transfer to/from parallel port. Loss of data may occur

when DMA is disabled in the middle of a data transfer from parallel port.

P_TC:

This bit will be set when the byte counter (P_BCNT) transitions to/from

0x000001 to 0x000000. This will generate an interrupt if enabled by

P_INT_EN and not disabled by P_TCI_DIS. During unchained transfers,

P_TC causes P_DMA_ON to be reset. When P_EN_NEXT = 0, P_TC is

cleared by P_INVALIDATE, P_RESET, or SB_RESET. When

P_EN_NEXT = 1, P_TC can also be cleared by writing a 1 to it.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

P_BURST_SIZE:

This field defines the sizes of SBus read and write bursts used by the FEPS

for parallel port transfers. All reads from memory will be one size, either 4,

8, or 1 word (in “no burst mode). SBus writes to memory can be byte, half-

word, or one of the burst sizes given in the table. The FEPS will always use

the largest possible size for writes, which is dependent on P_BURST_SIZE

and the number of bytes that need to be drained. Also, P_BURST_SIZE de-

termines the draining level of the P_FIFO. When the P_FIFO has been filled

with this amount of data, it will always be drained to memory. The sizes given

in Table 20 are in SBus words.

Table 20:

P_BURST_SIZ

RD_BURST_SIZ

WR_BURST_SIZES FIFO_Draining_Level

4 words

8 words

4 words

8 words

1 word

4, 8 words

No bursts

Reserved

No bursts

Reserved

SBus reads are always one word in no burst mode.

P_DMA_ON:

When set, indicates that the FEPS is able to respond to parallel port DMA re-

quests. Reads as 1 when (P_A_LOADED or P_NA_LOADED) and

P_EN_DMA & !(P_ERR_PEND); otherwise reads as 0.

REV_MIN [2:0]:

FEPS minor revision number.

REV_MAJ [3:0]:

FEPS major revision number. Starts from 2.

Example: for Rev x.y silicon, the {REV_MAJ[3:0], REV_MIN[2:0] = [x,y]}

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.2.2 DMA Address and Next Address Register

Table 21: DMA Address and Next Address Register Address

Physical Address

Access Size

DMA address and next address register (P_ADDR)

0xC80_0004

4 bytes

Table 22: DMA Address and Next Address Register Deﬁnition

Field

P_ADDR

P_NEXT_ADDR

Bits

31:0

Description

DVMA address register

Next DVMA address register

Type

R/W

This 32-bit read/write register contains the virtual address for parallel port

DMA transfers. It is implemented as a 32-bit loadable counter which points

to the next byte that will be accessed via the parallel port.

If the P_EN_NEXT (enable next address) bit in the P_CSR is set, then a

write to the P_ADDR register will write to the P_NEXT_ADDR register

instead. If P_EN_NEXT is set when the byte counter (P_BCNT) expires, and

the P_NEXT_ADDR register has been written since the last time the byte

counter expired, then the contents of P_NEXT_ADDR are copied into

P_ADDR. If P_EN_NEXT is set when the byte counter (P_BCNT) expires,

but the P_NEXT_ADDR register has not been written since the last time the

byte counter expired, then DMA activity is stopped and DMA requests from

the parallel port will be ignored until P_NEXT_ADDR is written or

P_EN_NEXT is cleared. (Also, the P_DMA_ON bit will read as 0 while

DMA is stopped because of this.) When DMA is re-enabled by writing to the

P_NEXT_ADDR register, the contents of P_NEXT_ADDR are copied into

P_ADDR before DMA activity actually begins.

Note: A write to the P_ADDR register will invalidate the P_FIFO. A

write to the P_NEXT_ADDR register does not have this effect.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.2.3 Byte Count Register

Table 23: Byte Count Register Address

Physical Address

Access Size

Byte count register (P_BCNT)

0xC80_0008

4 bytes

Table 24: Byte Count Register Deﬁnition

Field

P_BCNT

P_NEXT_BCNT

Bits

23:0

Description

DMA byte count register

Type

R/W

Next DMA byte count register

This register is implemented as a 24-bit down counter. When reading this reg-

ister as a word, bits 31:24 will read as 0s. The register should be loaded with

a 24-bit byte count which, if enabled via the P_EN_CNT bit in the P_CSR,

will be decremented every time a byte is transferred between the FEPS and

whatever external device is connected to the parallel port. During a transition

of this register from 1 to 0, the terminal count signal (P_TC), will generate an

interrupt if not disabled via the P_TCI_DIS bit of the P_CSR.

If the P_EN_NEXT bit in the P_CSR is set, then a write to the P_BCNT

P_NEXT_ADDR register is copied into the P_ADDR register, the

P_NEXT_BCNT register is copied into the P_BCNT register at the same

time. If P_NEXT_ADDR is being copied in P_ADDR and P_NEXT_BCNT

has not been written since the last time P_NEXT_BCNT was copied in

P_BCNT, the last value that was written into P_NEXT_BCNT will again be

copied into P_BCNT. This provides a shortcut in setting up consecutive

DMA transfers of equal size from different addresses, in that

P_NEXT_BCNT only needs to be written once as long as P_NEXT_ADDR

is loaded for each successive transfer. If P_EN_NEXT is not set when

P_BCNT expires (changes from 0x000001 to 0x000000), then parallel port

DMA activity will be stopped and the P_DMA_ON bit will read as 0 until

P_ADDR is written. If P_EN_NEXT is set, then DMA will be stopped on

P_BCNT expiration.

Note: Loading P_BCNT with 0 will allow 2**24 bytes to be trans-

ferred before it expires.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.2.4 Test Control/Status Register

Table 25: Test Control/Status Register Address

Physical Address

Access Size

Test control/Status register (P_TST_CSR)

0xC80_000C

4 bytes

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 26: Test Control/Status Register Deﬁnition

Field

LD_TAG

Bits

Description

Type

When set to 1. loads FIFO DMA address register

(ADDR_TAG) with value in D_ADDR

REQ_OUT

RD_BURST

WR_CNT

WRITE

Reads as 1, when FIFO is making a request for an

SBus read or write.

When set to 1, initiates a DMA burst read from

memory into FIFO from address in ADDR_TAG

When set to 1, loads FIFO_CNT register with

D_TST_CSR[5:0]

When set to 1, puts FIFO into WRITING mode.

Reads as 1 when FIFO in WRITING mode.

R/W

DRAIN

Reads as 1 if FIFO is draining. When set to 1,

forces FIFO to drain.

EMPTY

FULL

Reads as 1, if FIFO buffer empty.

Reads as 1, if FIFO buffer is full.

LO_MARK

Reads as 1, if FIFO buffer has enough room for 1

SBus read burst of data.

HI_MARK

COUNT

5:0

Reads as 1, if FIFO contains enough data for 1

SBus write burst.

Reads CNT register containing number of bytes

stored in FIFO buffer.

COUNT

When WR_CNT=1, write CNT register contain-

ing number of bytes stored in FIFO buffer.

Note:The P_TST_CSR is intended for diagnostic and test use only and should never be

written while a DMA transfer is active

7.2.5 Hardware Conﬁguration Register

Table 27: Hardware Conﬁguration Register Address

Physical Address

Access Size

Hardware conﬁguration register (P_HCR)

0xC80_0010

2 bytes

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 28: Hardware Conﬁguration Register Deﬁnition

Field

DSS

Bits

6:0

Description

Type

R/W

Data setup before data strobe in increments of 1 SBus clock

Unused. Reads as 0

DSW

TEST

14:8

Data strobe width in increments of 1 SBus clock

R/W

Test bit which when set, allows the buried counters to be

read

DSS:

Data setup to data strobe. This 7-bit quantity is used to define several differ-

ent timing specifications for the interface. The contents of this field of the reg-

ister are used to load a hardware timer whose timebase is the SBus clock. The

programmability range is from a minimum of 0 SBus clocks to 127 SBus

clocks. Bit 0 is the LSB and bit 6 is the MSB. The sections on unidirectional

and bidirectional transfers should be referenced for detail information on the

use of this timer.

DSW:

Data strobe width. This 7-bit quantity is used to define data strobe and ac-

knowledge pulse widths for the interface. The contents of this field of the reg-

ister are used to load a hardware timer whose timebase is the SBus clock. The

programmability range is from a minimum of 3 SBus clocks to 127 SBus

clocks. In the case of the value being 0, 1, 2, or 3, the timer will be loaded

with a value of 3. Bit 8 is the LSB and bit 14 is the MSB. The sections on uni-

directional and bidirectional transfers should be referenced for detail infor-

mation on the use of this timer.

7.2.6 Operation Conﬁguration Register

This 16-bit read/write register is used to specify the operation of the interface.

Bidirectional specification of the control signals (P_D_STRB, P_ACK,

P_BSY), handshake protocol, memory clear, and diagnostic mode are defined

in this register. The detailed function of the bits is described in Table 30. Re-

set value of this register is all bits 0, except DS_DSEL and IDLE, which are

reset to 1, and bit 1, which always reads as 1 for backward compatibility with

the HIOD parallel port.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 29: Operation Conﬁguration Register Address

Physical Address

Access Size

Operation conﬁguration register (P_HCR)

0xC80_0012

2 bytes

Table 30: Operation Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

R/W

Reserved

IDLE

Reads as 1, when the PP data transfer state machines

are idle

Reserved

SRST

When set, resets the parallel port. Must be reset by

software.

R/W

ACK_OP

Acknowledge operation

Busy operation

R/W

BUSY_OP

EN_DIAG

ACK_DSEL

When set, enables diagnostic operation

Acknowledge bidirectional select. When set,

P_BSY is bidirectional

BUSY_DSEL

DS_SEL

Busy bidirectional select. When set, P_D_STRB is

bidirectional

R/W

Data strobe bidirectional select. When set,

P_D_STRB is bidirectional

DATA_SRC

MEM_CLR

Data source for memory clear operation

When set, enables memory clear

R/W

IDLE:

When this bit is set, it indicates that the parallel port data transfer state ma-

chines are in their idle states. The state machines should be idle when chang-

ing direction and/or configuring operational modes and when enabling a

memory clear operation.

SRST:

Setting this bit will place the parallel port data transfer state machines and

programmable timers into reset. It will not reset any of the parallel port reg-

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

isters. This bit must be reset by software.

ACK_OP:

Used to specify the handshake protocol to be used on the interface. The mean-

ing of this bit differs depending on the direction of transfer. The sections on

unidirectional and bidirectional transfers should be referenced for detail in-

formation on this bit. The general definition is as follows:

1 = Handshake using PP_ACK

0 = PP_ACK is inactive

BUSY_OP:

Used to specify the handshake protocol to be used on the interface. The mean-

ing of this bit differs depending on the direction of transfer. The sections on

unidirectional and bidirectional transfers should be referenced for detail in-

formation on this bit. The general definition is as follows:

1 = Handshake performed using PP_BSY

0 = PP_BSY is not used for handshaking

EN_DIAG:

Setting this bit enables diagnostic mode which does three things:

• Bits 0–2 of the output register are gated on to bits 0–2 of the input reg-

ister. This allows testing of the data path and the interrupt generation

logic.

• The internal DS, ACK, and BUSY latch bits drive the internal DS_IRQ

and ACK_IRQ, and BUSY_IRQ interrupt-generation logic.

• When reading the DS, ACK, and BUSY bits of the transfer control reg-

ister, the read data comes from the internal latches instead of the exter-

nal pins. During diagnostic mode, if the DS or ACK bits are conﬁgured

as outputs, the output pins will be gated to an inactive level. The BUSY

output will be driven active and the DIR output will be latched in its

current state.

ACK_DSEL:

This bit is a bidirectional select for the PP_ACK signal. When this bit is 0,

PP_ACK is an input, when 1 it is a bidirectional signal. The PP_ACKDIR pin

will reflect the direction of PP_ACK. The switching of direction is controlled

by the DIR bit of the transfer control register. The function of the two pins

is as follows:

DIR=0

Input

DIR=1

Output

PP_ACK

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

PP_ACKDIR0

BUSY_DSEL:

This bit is a bidirectional select for the PP_BSY signal. When reset, PP_BSY

is fixed as an input. When set, PP_BSY is a bidirectional signal. The

PP_BSYDIR pin will reflect the direction of PP_BSY. The switching of di-

rection is controlled by the DIR bit of the transfer control register. The func-

tion of the two pins is as follows:

DIR=0

DIR=1

Output

PP_BSY Input

PP_BSYDIR0

DS_DSEL:

This bit is a bidirectional select for the PP_STB signal. When reset, PP_STB

is fixed as an output. When set, PP_STB is a bidirectional signal. The

PP_DSDIR pin will reflect the direction of PP_STB. The switching of direc-

tion is controlled by the DIR bit of the transfer control register. The function

of the two pins is as follows:

DIR=0

Output

DIR=1

Input

PP_STB

PP_DSDIR 1

This bit also defines transfer protocol as follows:

1 = Data strobe is bidirectional. Master write transfer protocol is selected.

0 = Data strobe is fixed as an output. Master read/write transfer protocol is

selected.

DATA_SRC:

This bit specifies the data to be sourced during a memory clear operation.

When set, the sourced data will be ones. When reset, the sourced data will be

0s.

MEM_CLR:

This bit enables memory clear operation. The DMA control registers need to

be configured, the DIR bit in the TCR register must be set and DMA must be

enabled.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.2.7 Parallel Data Register

The data register is an 8-bit read/write port used to transfer data to and from

the external device. In programmed I/O mode data written to this register is

presented to the I/O pins if the DIR bit of the transfer control register is 0. A

read of this register will result in the data previously written or if the DIR bit

of the transfer control register is set to 1, the latched data from the last data

strobe. The data port is not accessible via slave write cycles during DMA

(P_DMA_ON=1). Any write cycles during DMA will not generate errors, the

data will simply not be written.

Since both DMA and PIO share the same data register, internal loopback

is possible by running a single-byte DMA cycle followed by a PIO cycle to

verify the data. This will test both the DMA and slave data paths.

Table 31: Parallel Data Register Address

Physical Address

Access Size

Parallel data register (P_DR)

0xC80_0014

1 byte

Table 32: Parallel Data Register Deﬁnition

Field

P_DR

Bits

Description

Type

R/W

7:0

Parallel data

7.2.8 Transfer Control Register

The transfer control register is an 8-bit register whose contents define/reflect

the state of the external interface handshake and direction control signals. The

DS, ACK, and BUSY bits will reflect the state of the external pins, when read.

Writing these bits defines a value to be driven onto the external pins if the in-

dividual direction select bits (DS_DSEL, ACK_DSEL, BUSY_DSEL) and

the direction control bit (DIR) are configured such that the HIOD is driving

these pins as outputs. The write bits and read bits are different. That means

that values typically written to these bits may not be reflected on a read cycle.

However, by setting the EN_DIAG bit of the operation control register, these

OCR).

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 33: Transfer Control Register Address

Physical Address

Access Size

Transfer Control register (P_TCR)

0xC80_0015

1 byte

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 34: Transfer Control Register Deﬁnition

Field

Bits

Description

Type

R/W

Data strobe

ACK

BUSY

DIR

Acknowledge

Busy (active low)

Direction control. 0 = write to external device, 1 = read

Unused (reads as 0)

DS:

Reading this bit reflects the state of the bidirectional PP_STB pin. Writing

this bit with DS_DSEL=0 or with DS_SEL=1 and DIR=0 will cause the value

written to be driven onto PP_STB. The reset state of the output latch is 0, but

the value read back from this bit after reset will reflect the input signal being

driven onto PP_STB.

ACK:

Reading this bit reflects the state of the bidirectional PP_ACK pin. Writing

this bit with ACK_DSEL=1 will cause the value written to be driven onto

PP_ACK if DIR=1. The reset state of the output latch is 0, but the value read

back from this bit after reset will reflect the input signal being driven onto

PP_ACK.

BUSY:

Reading this bit reflects the state of the bidirectional PP_BSY pin. Writing

this bit with BUSY_DSEL=1 will cause the value written to be driven onto

PP_BSY if DIR=1. The reset state of the output latch is 0, but the value read

back from this bit after reset will reflect the input signal being driven onto

PP_BSY.

DIR:

This bit defines and controls the direction of data transfer: 0=write to external

device,

1= read from external device. It is also driven externally on the PP_DDIR pin.

This bit also controls the direction of DMA operation. In the case of a mem-

ory clear operation, this bit (must be set) and the MEM_CLR bits define the

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

DMA direction. The state of the DIR bit is reflected in the P_WRITE bit of

the P_CSR. Reset state of this bit is 1.

7.2.9 Output Register

The output register is an 8-bit read/write register whose contents are driven

on to the corresponding external pins. In diagnostic mode (EN_DIAG=1),

bits 0–2 are gated on to input register bits 0–2. The external outputs remain

low while diagnostic mode is enabled. All bits are 0 after reset.

Table 35: Output Register Address

Physical Address

Access Size

Output register (P_OR)

0xC80_0016

1 byte

Table 36: Output Register Deﬁnition

Field

SLCT_IN

AFXN

Bits

Description

Type

R/W

Select in. This bit is output on the PP_SLCT_IN pin.

Auto feed. This bit is output on the PP_AFXN pin.

Initialize. This bit is output on the P_INIT pin

Reserved (V1 bit on HIOD parallel port)

Reserved (V2 bit on HIOD parallel port)

Reserved (V3 bit on HIOD parallel port)

Unused (reads as 0)

INIT

Unused (reads as 0)

7.2.10 Input Register

The input register is an 8-bit read/write register whose contents reflect the

state of several external input pins and their corresponding interrupts. In di-

agnostic mode (EN_DIAG=1), bits 0–2 are driven from output register bits

0–2.

Table 37: Input Register Address

Physical Address

Access Size

Input register (P_IR)

0xC80_0017

1 byte

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 38: Input Register Deﬁnition

Field

ERR

Bits

Description

Type

Error input. This pin reﬂects the state of the ERR input pin

SLCT

Select input. This pin reﬂects the state of the SLCT input

Paper empty. This pin reﬂects the state of the PP_PE input

Unused (reads as 0)

7.2.11 Interrupt Control Register

This 16-bit read/write register is used to specify operation of the parallel port

interrupts. Interrupt enables, polarity, and IRQ pending bits are contained in

this register. The detailed function of these bits are described following the

table. Reset value of this register is all bits 0.

Table 39: Interrupt Control Register Address

Physical Address

0xC80_0018

Access Size

2 bytes

Interrupt Control register (P_ICR)

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 40: Interrupt Control Register Deﬁnition

Field

ERR_IRQ_EN

ERR_IRP

Bits

Description

Type

When set, enables ERR interrupts

R/W

ERR interrupt polarity. 1=on rising edge, 0=on

trailing edge

R/W

SLCT_IRQ_EN

SLCT_IRP

When set, enables SLCT interrupts

R/W

SLCT interrupt polarity. 1=on rising edge, 0=on

trailing edge

PE_IRQ_EN

PE_IRP

When set, enable PE interrupts

R/W

PE interrupt polarity. 1=on rising edge, 0=on

trailing edge

BUSY_IRQ_EN

BUSY_IRP

When set, enables BUSY interrupts

R/W

BUSY interrupt polarity. 1=on rising edge, 0=on

trailing edge

ACK_IRQ_EN

DS_IRQ_EN

When set, enables ACK interrupts on rising edge

of ACK

R/W

When set, enables DS interrupts on the rising

edge of DS

ERR_IRQ

SLCT_IRQ

PE_IRQ

When set, error IRQ pending

When set, select IRQ pending

When set, paper IRQ pending

When set, busy IRQ pending

When set, acknowledge IRQ pending

When set, data strobe IRQ pending

R/W

BUSY_IRQ

ACK_IRQ

DS_IRQ

*_IRQ_EN: When set, enables interrupts on the corresponding bits of the

input and transfer control registers. Note that the interrupt enable bit of the

PD_SCR must also be enabled to allow a hardware interrupt to be generated.

*_IRP: Defines the polarity of the edge triggered interrupts on the corre-

sponding bits of the input register. 0=interrupt generated on the 1 to 0

transition of the signal. 1= interrupt generated on the 0 to 1 transitions of the

signal. Note that when configuring the interrupt polarity of a given signal, it

is possible to generate a false interrupt. It is suggested that when the interrupt

polarities are being programmed, interrupts be disabled, and all interrupt

sources be cleared upon completion of programming.

ERR_IRQ, SLCT_IRQ, PE_IRQ, BUSY_IRQ:

When set, an interrupt is pending on the corresponding bit. The interrupt is

cleared and the bit is reset when a 1 is written to the corresponding bit. Writ-

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

ing a 0 to these locations leaves the bit(s) unchanged.

ACK_IRQ:

When set, an interrupt is pending due to the receipt of PP_ACK. The interrupt

is set on the 0 to 1 transition of PP_ACK. This interrupt is intended to facili-

tate PIO transfers while configured as master under master write protocol.The

interrupt is cleared and the bit is reset when a 1 is written to this bit. Writing

a 0 to this location leaves the bit unchanged.

DS_IRQ:

When set, an interrupt is pending due to the receipt of PP_STB. This interrupt

is intended to facilitate PIO transfers while configured as slave under master

write protocol. The interrupt is cleared and the bit is reset when a 1 is written

to this bit. Writing a 0 to this location leaves the bit unchanged.

7.3 SCSI Channel Registers

7.3.1 SCSI Control/Status Register

Table 41: Control/Status Register Address

Physical Address

0x880_0000

Access Size

4 bytes

Control/Status register (D_CSR)

Table 42: Control/Status Register Deﬁnition

Field

Bits

Description

Type

D_INT_PEND

Set when either FAS366_IRQ is active, or if

D_ERR_PEND is set, or if DVMA loop-back is

complete

D_ERR_PEND

D_DRAINING

Set when a SCSI DVMA transfer received an

SBus ERR acknowledge. Also set when a parity

error or a late error detected

Non-zero when buffers are draining SCSI data to

memory; 0 otherwise

Reserved

D_INT_EN

D_RESET

When set, enables SBus SCSI_IRQ when

INT_PEND or ERR_PEND is set

R/W

Reserved (reads as 0)

When set, invalidates the buffers and resets SCSI

R/W

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 42: Control/Status Register Deﬁnition

Field

D_WRITE

Bits

Description

Type

DMA direction for SCSI transfers; 1 = to mem-

ory, 0 = from memory

R/W

D_EN_DMA

When set, enables DMA from the FAS366

unless blocked by other conditions

R/W

D_REQ_PEND

D_DMA_REV

D_WIDE_EN

Do not assert D_RESET, while this is a 1

14:11 0001 for current implementation

When set, enables wide-mode SBus DVMA for

SCSI

R/W

Reserved (reads as 1)

D_DSBL_ESP_DR_

When set, disables drain of buffers on slave

accesses to the FAS366 registers

R/W

D_BURST_SIZE

19:18 Deﬁnes SCSI DVMA burst size (see table

below)

R/W

Reserved (reads as 1)

D_TWO_CYCLE

If set, provides a 2-cycle DMA access to

FAS366, else it is a 3-cycle access. Default value

is 0.

R/W

Reserved (reads as 0)

Reserved (reads as 1)

Reserved (reads as 0)

D_DSBL_PARITY_C

When set, disables checking for parity on the

bus. Default value is a 1.

R/W

D_PAUSE_FAS366

D_HW_RST_FAS366

D_DEV_ID

When asserted, it will cause FAS366 pause input

to be asserted. Default value is 0.

R/W

When asserted, it will cause the hardware reset

to FAS366 to be asserted. Default value is 0.

31:28 Device ID (1011 for this implementation)

Table 43: BURST_SIZE Encoding

BURST_SIZ

Read Burst Size

4 words

Write Burst Size

4 words

Buffer Drain Level

16 words

8 words

16 words

Reserved

16 words

D_INT_PEND:

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

This bit is set to indicate that FAS366 has asserted its interrupt signal. Once

FAS366 asserts its interrupt signal, all the bytes in prefetch buffers are

drained to the host memory, before setting this bit or generating an interrupt

on SBus. Draining of buffers, before posting the interrupt to device driver,

saves PIOs. This bit will also be set during DMA loop-back. This bit will also

be set when the D_ERR_PEND bit is set.

D_ERR_PEND:

This bit is set in response to an Error ACK, during DVMA. This bit is reset

on setting D_RESET. This bit will also be set, when a parity error or a late

error is detected.

D_DRAINING:

When the buffers are draining to memory, this bit is set. DO NOT assert

D_RESET or write to D_ADDR register when set. This bit is not valid while

D_ERR_PEND is set and should be ignored.

D_RESET:

This bit will remain active once set to 1, until set to 0 or is cleared by a hard-

ware reset. Setting D_RESET or asserting hardware reset will invalidate the

prefetch buffers, reset all of the state machines to their idle states.

Note: This bit must be asserted at the end of each DMA transfer. In

other words, whenever D_ADDR and D_BCNT are programmed with

a new value, D_RESET should have been asserted prior to this

programming.

D_REQ_PEND: This bit is set when a DVMA read or write request is pend-

ing. Do not assert D_RESET when D_REQ_PEND or/and D_DRAINING

bit(s) is (are) set.

D_DSBL_ESP_DRN: If set, draining will not be forced when the CPU

makes a slave access to the FAS366, while SCSI DVMA is in progress. This

bit could be useful in block-mode operation, where FAS366 does not generate

interrupts on successful execution of commands. In such a case, device driv-

ers can use this bit to prevent forced draining, when making a slave access to

the FAS366 to monitor status.

7.3.2 SCSI Address Register

This register indicates the starting address from which DMA transfer takes

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

place.

Table 44: SCSI Address Register Address

Physical Address

Access Size

Address register (D_ADDR)

0x880_0004

4 bytes

Table 45: SCSI Address Register Deﬁnition

Field

D_ADDR

Bits

Description

Virtual address used in SCSI DVMA access

Type

31:0

R/W

Note: To determine the exact address at which an error occurred, two

cases have to be dealt with. These are the following:

Case 1: The error occurs on the SCSI Bus

For this case, the starting address of the block/command is known, as

this is programmed before any data movement between FAS366 and

SCSI DMA block takes place. Reading of transfer count register from

FAS366, would indicate the number of data bytes read/written. Using

the starting address and the byte count, the exact address can be calcu-

lated.

Case 2: The error occurs on the SBus

Data on the SBus is always moved in a DMA burst of byte/half-

word/word/double word for up to 64 bytes. A read of D_ADDR

will take place. In a burst of 64/32/16 etc., if an error occurred on the

SBus, it will not be possible to identify the exact location at which an

error on SBus occurred.

7.3.3 SCSI Byte Count Register

Table 46: SCSI Byte Count Register Address

Physical Address

0x880_0008

Access Size

Byte Count register (D_BCNT)

4 bytes

Table 47: SCSI Byte Count Register Deﬁnition

Field

D_BCNT

Bits

Description

Type

R/W

31:0

DVMA transfer length counter

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

• Byte counter is decremented, every time a byte is transferred between

SCSI and FAS366.

• No interrupt is generated when the D_BCNT reaches 0 (expires).

• D_BCNT will clear to 0, if D_RESET is asserted.

• D_BCNT should not be programmed with a number, different than the

one in the transfer count register of FAS366.

7.3.4 SCSI Test Control/Status Register

Table 48: SCSI Test Control/Status Register Address

Physical Address

Access Size

Test control/Status register (D_TST_CSR)

0x880_000C

1 byte

Table 49: SCSI Test Control/Status Register Deﬁnition

Field

Bits

Description

Type

PARITY_ERROR

Set when a parity error is detected on the

internal channel engine interface (CEI)

R/W

LATE_ERROR

Set when a late error is detected on the CEI

R/W

LOOP-BACK MODE

When set, programs the SCSI channel to be

in DMA LOOP_BACK mode

LOOP-

BACK_DONE

When set, indicates that DMA LOOP-BACK

is complete

ERROR_ACK

Set when an error ACK is detected on the CEI

Parity_Error:

This bit is set if a parity error is detected on the CEI. It will cleared on a hard-

ware reset or a software reset (D_RESET).

Late_Error:

This bit is set if a late error is detected on the CEI. It will cleared on a hard-

ware reset or a software reset (D_RESET).

Loop_Back_Mode:

This bit when set, enables the loop-back mode on the SCSI channel. The

SCSI CE will provide a DMA loop-back mode, in which, data from the host

memory will be moved to the prefetch buffers. Once the data is in the prefetch

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

buffers, it will be looped back to host memory. FAS366 is completely by-

passed during this operation.

As the prefetch buffers can store 128 bytes, 128 bytes will be moved from

the host memory to SCSI CE. After the DMA read is complete the 128 bytes

will be looped back to host memory, by a DMA write. Bit[2] of D_TST_CSR

D_TST_CSR register will indicate that loop-back is complete. The starting

address should be programmed at a 64-byte boundary.

For a programmer, the following will be the sequence of events.

1. Reset the SCSI CE.

2. Program the starting address in D_ADDR register.

3. Program the D_BCNT to 128 bytes.

4. Set the bit[2] of D_TST_CSR to select the loop-back mode.

5. Select DMA read (by writing to WRITE bit in D_CSR), Burst

Size should be programmed for 64B.

6. Enable DMA.

7. Wait for interrupt.

8. After the interrupt, look at bit[3] of D_TST_CSR.

9. If the bit[3] is set, 128 bytes of data from host memory has been

moved into the prefetch buffers.

10. Reset the SCSI CE.

11. Program the starting address in D_ADDR reg, this is the address

where data coming out to prefetch buffers, will be written in host

memory.

12. Program the D_BCNT to 128 bytes.

13. Set the bit[2] of D_TST_CSR.

14. Select DMA write (by writing to the WRITE bit in CSR), Burst

Size should be programmed for 64 bytes.

15. Enable DMA.

16. Wait for interrupt.

17. After the interrupt, look at bit[3] of D_TST_CSR.

18. If this bit is set, 128 bytes from the prefetch buffers have been

written back to the host memory.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

This completes the loop-back of 128 bytes. This sequence can be repeated

any number of times.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.4 FAS366 (SCSI Controller Core) Registers

The FAS366 registers are used by the CPU to control the operation of the

SCSI bus. Through these registers, the CPU configures, commands, and mon-

itors data, command, and information transfers between the FAS366 and the

SCSI bus.

Note: For the case of SCSI read (data-in phase only) when FAS366 is

operating in narrow mode and if the number of bytes coming to

FAS366 from the target is an odd number, FAS366 can be pro-

grammed in two modes.

1) FAS366 does not give up the last one byte. It generates an interrupt

when the last one byte is still in FAS366 FIFO. The device driver has

to make a slave access to FAS366 to write one byte so that the last byte

is padded. Then the device driver can make another slave access to read

both the bytes out and discard the padded byte. This is the default

mode.

2) FAS366 pads the last byte and generates an interrupt only after the

SCSI CE has read all the bytes. This mode can be entered by setting the

bit 7 of the configuration register #3. This bit gets cleared after every

reset.

7.4.1 FAS366 Transfer Counter Low Register (Read Only)

This 16-bit transfer counter register consists of two eight-bit, read-only reg-

isters. The counter is used to count the number of bytes transferred in a DMA

command or received in a command sequence in target mode. When a DMA

command is issued, the transfer counter is loaded with the value contained in

the transfer count register. The value in the transfer counter is decremented as

bytes are transferred.

When a sequence terminates early, the sum of the transfer counter and the

FIFO flags registers indicate the number of bytes remaining to be transferred.

Table 50: FAS366 Transfer Counter Low Register (Read Only) Address

Physical Address

Access Size

Transfer counter low

0x881_0000

2 bytes

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 51: FAS366 Transfer Counter Low Register (Read Only) Deﬁnition

Field

Bits

Description

Type

Transfer counter low

15:0

Holds the 16 bits of transfer counter

7.4.2 FAS366 Transfer Count Low Register (Write Only)

This 16-bit transfer count register is comprised of two eight-bit, write-only

registers. The transfer count register is normally loaded prior to writing a

DMA command to the command register. This value indicates the number of

bytes to be transferred into the FIFO.

Table 52: FAS366 Transfer Count Low Register (Write Only) Address

Physical Address

Access Size

Transfer count low

0x881_0000

2 bytes

Table 53: FAS366 Transfer Count Low Register (Write Only) Deﬁnition

Field

Bits

Description

Type

Transfer count low

15:0

Programmed with 16 bits of transfer count

7.4.3 FAS366 Transfer Counter High Register (Read Only)

Table 54: FAS366 Transfer Counter High (Read Only) Register Address

Physical Address

Access Size

Transfer counter high

0x881_0004

2 bytes

Table 55: FAS366 Transfer Counter High (Read Only) Register Deﬁnition

Field

Bits

Description

Type

Transfer counter high

15:0

Holds the 16 bits of transfer counter

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.4.4 FAS366 Transfer Count High (Write Only) Register

Table 56: FAS366 Transfer Count High Register (Write Only) Address

Physical Address

Access Size

Transfer count high

0x881_0004

2 bytes

Table 57: FAS366 Transfer Count High Register (Write Only) Deﬁnition

Field

Bits

Description

Type

Transfer count high

15:0

Programmed with 16 bits of transfer count

7.4.5 FAS366 FIFO Register

The SCSI data FIFO consists of 16 registers, each two bytes wide. Data can

be read/written from/to FIFO, with a slave or DMA access. The data is loaded

into the FIFO top register and is unloaded from the FIFO bottom register.

Table 58: FAS366 FIFO Register Address

FIFO register

Physical Address

Access Size

0x881_0008

1 byte

Table 59: FAS366 FIFO Register Deﬁnition

Field

Bits

Description

Type

R/W

FIFO

7:0

Data port for FIFO access

7.4.6 FAS366 Command Register

The command register is an eight-bit, read/write register that functions as a

two-byte deep FIFO, enabling the CPU to stack commands to the FAS366.

Each command loaded into the command register is defined by an eight-bit

command code, which consists of the DMA indicator, the command mode,

and the command indicator.

Table 60: FAS366 Command Register Address

Physical Address

Access Size

Command register

0x881_000C

1 byte

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 61: FAS366 Command Register Deﬁnition

Field

Command

Bits

Description

Type

7:0

Functions as a 2-byte deep command holder

R/W

7.4.7 FAS366 Status #1 Register

This eight-bit, read-only register indicates the status of the FAS366 core and

the SCSI bus phase, and qualifies the reason for an interrupt.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 62: FAS366 Status #1 Register Address

Status #1 register

Physical Address

Access Size

0x881_0010

1 byte

Table 63: FAS366 Status #1 Register Deﬁnition

Field

Bits

Description

Indicates the status of FAS366 and SCSI bus phase

Type

Status #1

7:0

7.4.8 FAS366 Select/Reselect Bus ID Register

The select/reselect bus ID register is an eight-bit, write-only register that

stores encoded values for the SCSI bus ID and the selection/reselection ID.

Table 64: FAS366 Select/Reselect Bus ID Register Address

Physical Address

Access Size

Select/Reselect bus ID register

0x881_0010

1 byte

Table 65: FAS366 Select/Reselect Bus ID Register Deﬁnition

Field

Bits

Description

Stores encoded values for SCSI bus ID

Type

Select/Reselect bus ID

7:0

7.4.9 FAS366 Interrupt Register

This eight-bit, read-only register is used in conjunction with information con-

tained in the Status #1 register and sequence step register to determine the

cause of an interrupt. This register reflects the status of the completed com-

mand. Reading the interrupt register while an interrupt is pending clears all

interrupt register bits to 0.

Table 66: FAS366 Interrupt Register Address

Interrupt register

Physical Address

Access Size

0x881_0014

1 byte

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 67: FAS366 Interrupt Register Deﬁnition

Field

Bits

Description

Type

Interrupt register

7:0

Used for determination of the cause of an interrupt

7.4.10 FAS366 Select/Reselect Time-Out Register

The select/reselect time-out register is an eight-bit, write-only register that

specifies the amount of time to wait for a response during selection or rese-

lection. The select/reselect time-out register is typically loaded to specify a

time-out period of 250 ms.

Table 68: FAS366 Select/Reselect Time-Out Register Address

Physical Address

Access Size

Select/reselect time-out register

0x881_0014

1 byte

Table 69: FAS366 Select/Reselect Time-Out Register Deﬁnition

Field

Bits

Description

Type

Select/reselect time-out

7:0

Used for specifying the response time

during selection/reselection

7.4.11 FAS366 Sequence Step Register

Sequence step register bits are latched until the interrupt register is read.

Reading the Interrupt register while an interrupt is pending clears the se-

quence step register to 0.

Table 70: FAS366 Sequence Step Register Address

Physical Address

Access Size

Sequence step register

0x881_0018

1 byte

Table 71: FAS366 Sequence Step Register Deﬁnition

Field

Bits

Description

Indicates the last executed sequence/step

Type

Sequence step

7:0

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.4.12 FAS366 Synchronous Transfer Period Register

The synchronous transfer period register is an eight-bit, write-only register.

This register specifies the minimum time, in input clock cycles, between lead-

ing edges of successive REQ or ACK pulses on the SCSI bus during synchro-

nous data transfers.

Table 72: FAS366 Synchronous Transfer Period Register Address

Physical Address

Access Size

Synchronous transfer period register

0x881_0018

1 byte

Table 73: FAS366 Synchronous Transfer Period Register Deﬁnition

Field

Bits

Description

Type

Synchronous transfer

period

7:0

Speciﬁes the time between successive REQ

and ACK pulses on the SCSI bus

7.4.13 FAS366 FIFO Flags Register

The FIFO flags register is an eight-bit, read-only register that provides the

user with the option of addressing only one register for FIFO count and se-

quence information.

Table 74: FAS366 FIFO Flags Register Address

Physical Address

Access Size

FIFO ﬂags register

0x881_001C

1 byte

Table 75: FAS366 FIFO Flags Register Deﬁnition

Field

FIFO ﬂags

Bits

Description

Type

7:0

Provides information on FIFO

7.4.14 FAS366 Synchronous Offset Register

The synchronous offset register is an eight-bit, write-only register. This reg-

ister specifies the maximum REQ/ACK offset allowed during synchronous

transfers. An offset of 0 specifies asynchronous operation.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 76: FAS366 Synchronous Offset Register Address

Physical Address

Access Size

Synchronous offset register

0x881_001C

1 byte

Table 77: FAS366 Synchronous Offset Register Deﬁnition

Field

Bits

Description

Type

Synchronous offset

7:0

Speciﬁes the REQ/ACK offset during syn-

chronous transfers

7.4.15 FAS366 Conﬁguration #1 Register

The configuration #1 register is an eight-bit, read/write register that specifies

different operating options for the FAS366.

Table 78: FAS366 Conﬁguration #1 Register Address

Physical Address

Access Size

Conﬁguration #1 register

0x881_0020

1 byte

Table 79: FAS366 Conﬁguration #1 Register Deﬁnition

Field

Bits

Description

Speciﬁes different operation options for FAS366

Type

Conﬁguration #1

7:0

R/W

7.4.16 FAS366 Clock Conversion Factor Register

The clock conversion factor register enables the software pause and the fast

sync response time; sets parity ATN and interrupt masks; and indicates the

clock conversion factor.

Table 80: FAS366 Clock Conversion Factor Register Address

Physical Address

Access Size

Clock conversion factor register

0x881_0024

1 byte

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 81: FAS366 Clock Conversion Factor Register Deﬁnition

Field

Bits

Description

Type

Clock conversion factor

7:0

Allows for fast synchronous response time,

set parity ATN and interrupt masks and

indicates the clock conversion factor

7.4.17 FAS366 Status #2 Register

The status #2 register is a read-only register that indicates detailed status in-

formation about the FIFO, the DMA interface, the sequence counter, the

transfer counter, the recommand counter, and the command register.

Table 82: FAS366 Status #2 Register Address

Physical Address

Access Size

Status #2 register

0x881_0024

1 byte

Table 83: FAS366 Status #2 Register Deﬁnition

Field

Status #2

Bits

Description

Indicates status of FAS366 and SCSI bus

Type

7:0

7.4.18 FAS366 Test Register

The test register is an eight-bit, write-only register that is used during produc-

tion chip testing to test the FAS366 in various modes.

Table 84: FAS366 Test Register Address

Test register

Physical Address

Access Size

0x881_0028

1 byte

Table 85: FAS366 Test Register Deﬁnition

Field

Bits

Description

Used during production chip testing to test FAS366

Type

Test

7:0

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.4.19 FAS366 Conﬁguration #2 Register

Configuration #2 is an eight-bit read/write register that specifies different op-

erating options for the FAS366.

Table 86: FAS366 Conﬁguration #2 Register Address

Physical Address

Access Size

Conﬁguration #2 register

0x881_002C

1 byte

Table 87: FAS366 Conﬁguration #2 Register Deﬁnition

Field

Bits

Description

Speciﬁes different operating options for FAS366

Type

Conﬁguration #2

7:0

R/W

7.4.20 FAS366 Conﬁguration #3 Register

This eight-bit, read/write register is used to enable normal or fast synchronous

transfer timing, ID message reserved bit checking, receipt of three-byte mes-

sages when selected with ATN, and recognition of 10-byte Group 2 com-

mands.

Table 88: FAS366 Conﬁguration #3 Register Address

Physical Address

Access Size

Conﬁguration #3 register

0x881_0030

1 byte

Table 89: FAS366 Conﬁguration #3 Register Deﬁnition

Field

Bits

Description

Speciﬁes different operating options for FAS366

Type

Conﬁguration #3

7:0

R/W

7.4.21 FAS366 Recommand Counter Register

The 16-bit recommand counter consists of two eight-bit, read/write registers:

the recommand counter low register, and the recommand counter high regis-

ter. The recommand counter is enabled when the recommand function is en-

abled, and is disabled when the recommand functions is disabled. The

recommand counter is decremented at the end of each block transfer before

the SCSI command is re-executed.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 90: FAS366 Recommand Counter Register Address

Physical Address

Access Size

Recommand counter low register

Recommand counter high register

0x881_0038

0x881_003C

1 byte

Table 91: FAS366 Recommand Counter Register Deﬁnition

Field

Bits

Description

Type

Recommand count low

Recommand count high

7:0

Lower 8 bits of recommand count

Upper 8 bits of recommand count

R/W

After power-up or a chip reset, and until the recommand counter register is

loaded, the FAS366 part-unique ID code is readable from the recommand

counter low register. This part-unique ID indicates FAS366 family code and

the revision level at power-up.

7.5 Ethernet Channel Registers

7.5.1 Global Software Reset Register

This two-bit register is used to perform an individual software reset to the

ETX or ERX modules (when the corresponding bit is set), or a global soft-

ware reset to the entire Ethernet channel (when both bits are set). These bits

can be set to 1 using a programmed I/O write to the defined address. They be-

come self-cleared after the corresponding reset command has been executed.

Table 92: Global Software Reset Register Address

Physical Address

Access Size

Global software reset register

0x8C0_0000

4 bytes

Table 93: Global Software Reset Register Deﬁnition

Field

Bits

Description

Type

R/W

ETX software reset

ERX software reset

Individual software reset to the ETX module

Individual software reset to the ERX module

Reserved

31:2

Note: To ensure proper operation of the hardware after a software reset

(individual or global), this register must be polled by the software.

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

When both bits read back as 0s, the software is allowed to continue to

program the hardware.

7.5.2 Global Conﬁguration Register

This five-bit register is used to determine the system-related parameters that

control the operation of the DMA channels.

Table 94: Global Conﬁguration Register Address

Physical Address

Access Size

Global conﬁguration register

0x8C0_0004

4 bytes

Table 95: Global Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Burst_Size

1:0

This ﬁeld determines the size of the host bus

bursts that the DMA channels will execute:

R/W

00 — 16-byte burst

01 — 32-byte burst

10 — 64-byte burst

11 — Reserved

Extended_Transfer_Mode

Parity_Enable

When set to 1, 64-bit CEI and SBus DVMA

transactions will be performed. If cleared to 0,

a 32-bit CEI/SBus is assumed

R/W

When set to 1, parity checking is performed

for DVMA read and PIO write cycles

R/W

27:4 Reserved

Ethernet channel ID

31:28 This ﬁeld identiﬁes the version number of the R/W

Ethernet channel. Current version # is 0000

7.5.3 Global Interrupt Mask Register (RW)

This 32-bit register is used to determine which status events will cause an in-

terrupt. If a mask bit is cleared to 0, the corresponding event causes an inter-

rupt signal to be generated on the SBus. The layout of this register

corresponds bit-by-bit to the layout of the status register, with the exception

of bit [23]. The MIF interrupt is not maskable here, and should be masked at

the source of the interrupt in the MIF.

Default value is 0xFF7FFFFF.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 96: Global Interrupt Mask Register Address

Physical Address

Access Size

Global interrupt mask register

0x8C0_0104

4 bytes

7.5.4 Global Status Register

This 32-bit register is used to communicate the software events that were de-

tected by the hardware. If a status bit is set to 1, it indicates that the corre-

sponding event has occurred. All the bits are automatically cleared to 0 when

the status register is read by the software, with the exception of bit [23]. The

MIF status bit will be cleared after the MIF status register is read.

Table 97: Global Status Register Address

Physical Address

Access Size

Global status register

0x8C0_0100

4 bytes

Table 98: Global Status Register Deﬁnition

Field

Bits

Description

A frame transfer from the RX_MAC to the RxFIFO has

been completed

Type

Frame_Received

Rx_Frame_Counter_Expired

The Rx_Frame_Counter rolled over from FFFF to 0000

Alignment_Error_Counter_Expired

The Alignment_Error_Counter rolled over from FF to

CRC_Error_Counter_Expired

Length_Error_Counter_Expired

RxFIFO_Overﬂow

The CRC_Error_Counter rolled over from FF to 00

The Length_Error_Counter rolled over from FF to 00

The synchronous FIFO in the RX_MAC has an over-

ﬂow. A receive frame was dropped by the RX_MAC

Code_Violation_Counter_Expired

SQE_Test_Error

The Code_Violation_Counter rolled from FF to 00

A signal quality error was detected in the XIF

Frame_Transmitted

The TX_MAC has sucessfully transmitted a frame on

the medium

TxFIFO_Underrun

The TX_MAC has experienced an underrun in the syn-

chronous FIFO due to data starvation caused by transmit

DMA

Max_Packet_Size_Error

The TX_MAC attempted to transmit a frame that

exceeds the maximum size allowed

Normal_Collision_Counter_Expired

The Normal_Collision_Counter rolled over from FFFF

to 0000

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 98: Global Status Register Deﬁnition

Field

Bits

Description

Type

Excessive_Collision_Counter_Expired

The Excessive_Collision_Counter rolled over from FF

to 00

Late_Collision_Counter_Expired

First_Collision_Counter_Expired

The Late_Collision_Counter rolled over from FF to 00

The First_Collision_Counter rolled over from FFFF to

0000

Defer_Time_Expired

Rx_Done

The Defer_Timer rolled over from FFFF to 0000

A frame transfer from RxFIFO to the host memory has

been completed

Rx_Buffer_Not_Available

The receive DMA engine tried to transfer a receive

frame from the RxFIFO to the host memory, but did not

ﬁnd any descriptors that were available. The frame was

dropped by the DMA engine.

Rx_Master_Err_Ack

Rx_Late_Err

An Error ACK occurred during a receive DMA cycle

A late error occurred during a receive DMA cycle

Rx_DMA_Par_Err

A parity error was detected during a receive DMA read

cycle (descriptor access)

Rx_Tag_Err

EOP_Error

The receive unload control state machine did not see two

consecutive tag bits

The transmit load control detected a descriptor with the

OWN bit cleared, before the last descriptor of the current

frame (EOP = 1) has been processed

MIF_Interrupt

Tx_Done

Tx_All

The status register in the MIF has at least one unmasked

interrupt set

A frame transfer from the host memory to the TxFIFO

has completed

The transmit DMA has transferred to the TxFIFO all the

frames that have been posted to it by software. There are

no transmit descriptors that are currently owned by the

hardware

Tx_Master_Err_Ack

Tx_Late_Err

An Error ACK occurred during a transmit DMA cycle

A late error occurred during a transmit DMA cycle

Tx_DMA_Par_Err

A parity error was detected during a transmit DMA read

cycle

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 98: Global Status Register Deﬁnition

Field

Bits

Description

Type

Tx_Tag_Err

The transmit unload control state machine did not see

two consecutive tag bits set

Slave_Err_Ack

An Error ACK was generated by the hardware during a

PIO cycle to the Ethernet channel area. This is an indica-

tion that the PIO cycle was executed with SB_SIZE

other than a word transfer

Slave_Par_Err

A parity error was detected during a PIO write cycle to

the Ethernet channel

7.5.5 ETX Transmit Pending Command

Table 99: ETX Transmit Pending Command Address

Physical Address

Access Size

4 bytes

ETX transmit pending command

0x8C0_2000

This one-bit command must be issued by the software for every packet that

the driver posts to the hardware. The bit is set to 1 using a programmed I/O

write to the defined address. This bit becomes self-cleared after the command

has been executed. This command is used as a wake up signal to the transmit

DMA engine.

7.5.6 ETX Conﬁguration Register

This 10-bit register determines the ETX-specific parameters that control the

operation of the transmit DMA channel.

Table 100: ETX Conﬁguration Register Address

Physical Address

Access Size

ETX conﬁguration register

0x8C0_2004

4 bytes

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 101: ETX Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Tx_DMA_Enable

When set to 1, the DMA operation of the channel

is enabled. The load control state machine will

respond to the next TX_Pending command. When

cleared to 0, the DMA operation of the channel

will cease as soon as the transfer of the current data

buffer has been completed

R/W

Tx_FIFO_Threshol

9:1

This ﬁeld determines the number of packet data

words that will be loaded into the TxFIFO before

the frame transmission by the TX_MAC is

enabled.

R/W

The maximum allowable threshold is 1BF. If the

desire is to buffer an entire standard Ethernet

frame before transmission is enabled, this ﬁeld has

to be programmed to a value greater than 1BF.

Paced_Mode

When set to 1, the Tx_All interrupt (bit 25 in the

global status register) will become set only after

the TxFIFO becomes empty. If cleared to 0, the

Tx_All interrupt will function as described in

“Global Interrupt Mask Register (RW)” section on

page 94.

R/W

The default value of this register is set to 0x3FE

7.5.7 ETX Transmit Descriptor Pointer (RW)

This 29-bit register points to the next descriptor in the ring. The 21 most sig-

nificant bits are used as the base address for the descriptor ring, while the 8

least significant bits are used as a displacement for the current descriptor.

Table 102: ETX Transmit Descriptor Pointer Register Address

Physical Address

Access Size

ETX transmit descriptor pointer register

0x8C0_2008

4 bytes

Note: The transmit descriptor pointer must be initialized to a 2K byte-

aligned value after power-on or software reset.

7.5.8 ETX Transmit Descriptor Ring Size

This four-bit register determines the number of descriptor entries in the ring.

The number of entries can vary from 16 through 256 in increments of 16.

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 103: ETX Transmit Descriptor Ring Size Register Address

Physical Address

Access Size

ETX transmit descriptor ring size register

0x8C0_202C

4 bytes

Default: 0xF; 256 descriptor entries.

7.5.9 ETX Transmit Data Buffer Base Address

Table 104: ETX Transmit Data Buffer Base Address Register Address

Physical Address

Access Size

ETX transmit data buffer base address register

0x8C0_200C

4 bytes

Table 105: ETX Transmit Data Buffer Base Address Register Deﬁnition

Field

Bits

Description

Type

Transmit data

buffer base address

31:0

This 32-bit register points to the beginning of

the transmit data buffer in the host memory. It

is loaded by the DMA state machine during the

descriptor fetch phase. This register is used to

generate the DVMA burst address by adding to

it the data buffer displacement.

7.5.10 ETX Transmit Data Buffer Displacement (RO)

This 10-bit counter keeps track of the next DVMA read burst address. It is

used as a displacement for the data buffer base address. The counter incre-

ments by 1, 2, or 4 (depending on the burst size) after a DVMA read burst cy-

cle has been executed by the transmit DMA engine. The counter is cleared

when the data buffer base address is loaded by the DMA state machine. This

base address.

Table 106: ETX Transmit Data Buffer Displacement Register Address

Physical Address

Access Size

ETX transmit data buffer displacement register

0x8C0_2010

4 bytes

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 107: ETX Transmit Data Buffer Displacement Register Deﬁnition

Field

Bits

Description

Type

Transmit data buffer

displacement

9:0

10-bit counter, keeps track of the next

DVMA read burst address

7.5.11 ETX Transmit Data Pointer

This 32-bit register points to the next DVMA read burst address. Its contents

is the sum of the transmit data buffer base address and the transmit data buffer

displacement.

Table 108: ETX Transmit Data Pointer Register Address

Physical Address

Access Size

ETX transmit pointer register

0x8C0_2030

4 bytes

Table 109: ETX Transmit Data Pointer Register Deﬁnition

Field

Bits

Description

Type

Transmit data pointer

31:0

Points to next DVMA read burst address.

Value is the sum of

Data_Buffer_Base_Address and

Data_Buffer_Displacement

7.5.12 ETX TxFIFO Packet Counter

This eight-bit up/down counter keeps track of the number of frames that cur-

rently reside in the TxFIFO. The counter increments when a frame is loaded

into the FIFO, and decrements when a frame has been transferred to the

TX_MAC. This counter is used to enable frame transfer from the TxFIFO to

the TX_MAC.

Table 110: ETX TxFIFO Packet Counter Register Address

Physical Address

Access Size

ETX TxFIFO packet counter register

0x8C0_2024

4 bytes

100

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 111: ETX TxFIFO Packet Counter Register Deﬁnition

Field

Bits

Description

Type

TxFIFO packet counter

7:0

Up/down counter to keep track of number

of frames currently in the TxFIFO

R/W

7.5.13 ETX TxFIFO Write Pointer

This nine-bit loadable counter points to the next location in the FIFO that will

be loaded with SBus data, the checksum, or the frame control word. The

counter increments by 1 or 2 (depending on SBus configuration) after a word

(or double word) was loaded into the FIFO. The counter is loaded with the

contents of shadow write pointer, plus the appropriate offset, when the check-

sum is stuffed into the frame. This counter is used to generate the write ad-

dress for the TxFIFO memory core.

Table 112: ETX TxFIFO Write Pointer Register Address

Physical Address

Access Size

ETX TxFIFO write pointer register

0x8C0_2014

4 bytes

Table 113: ETX TxFIFO Write Pointer Register Deﬁnition

Field

Bits

Description

Type

TxFIFO write pointer

8:0

Counter that points to next location in FIFO

that will be loaded with SBus data, check-

sum or frame control word

R/W

7.5.14 ETX TxFIFO Shadow Write Pointer

This nine-bit register points to the first byte of the packet that is either cur-

rently being loaded or is about to be loaded into the FIFO. The register is

loaded with the contents of the write pointer after the packet transfer from the

SBus to the FIFO has been completed. When the write pointer is used to stuff

the checksum into the frame, this register serves as a temporary hold register

for the write pointer.

101

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 114: ETX TxFIFO Shadow Write Pointer Register Address

Physical Address

Access Size

TxFIFO shadow write pointer register

0x8C0_2018

4 bytes

Table 115: ETX TxFIFO Shadow Write Pointer Register Deﬁnition

Field

Bits

Description

Type

TxFIFO shadow write pointer

8:0

Points to the ﬁrst byte of the packet

that is either currently being loaded or

is about to be loaded into the FIFO.

R/W

7.5.15 ETX TxFIFO Read Pointer

This nine-bit loadable counter points to the next location in the FIFO that will

be read from to retrieve packet data that is transferred to the TX_MAC. The

counter increments by 1 or 2 (depending on SBus configuration) after a word

(or double word) was read from the FIFO. The counter is loaded with the con-

tents of the shadow read pointer, when a retry occurs due to a collision on the

network. This counter is used to generate the read address for the TxFIFO

memory core.

Table 116: ETX TxFIFO Read Pointer Register Address

Physical Address

Access Size

TxFIFO read pointer register

0x8C0_201C

4 bytes

Table 117: ETX TxFIFO Read Pointer Register Deﬁnition

Field

Bits

Description

Type

TxFIFO read pointer

8:0

Counter that points to next location in

FIFO that will be read from to retrieve data

that will be transferred to TX_MAC

R/W

7.5.16 ETX TxFIFO Shadow Read Pointer

This nine-bit register points to the first byte of the packet that is either cur-

rently being unloaded or is about to be unloaded from the TxFIFO. The reg-

ister is loaded with the contents of the read pointer after the packet transfer

from the FIFO to the TX_MAC has been completed. This register is used to

102

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

rewind the read pointer for frame retransmission due to a collision on the net-

work.

Table 118: ETX TxFIFO Shadow Read Pointer Address

Physical Address

Access Size

TxFIFO shadow read pointer register

0x8C0_2020

4 bytes

Table 119: ETX TxFIFO Shadow Read Pointer Deﬁnition

Field

Bits

Description

Type

TxFIFO shadow read pointer

8:0

Points to ﬁrst byte of the packet cur-

rently being unloaded or is about to

be unloaded from TxFIFO

R/W

7.5.17 ETX State Machine Register

This 23-bit register provides the current state for all the state machines in

ETX.

Table 120: ETX State Machine Register Address

Physical Address

Access Size

State machine register

0x8C0_2028

4 bytes

Table 121: ETX State Machine Register Deﬁnition

Field

Bits

4:0

Description

Checksum state machine state

Chaining state machine state

Unload control state machine state

Load control state machine state

Type

11:5

16:12

22:17

7.5.18 ETX TxFIFO

For diagnostic purposes a PIO path has been provided into the TxFIFO. When

using PIOs, the configuration of the TxFIFO will be 512 × 33 bits. In order to

be able to access all the bits in the memory core, the address space of the

TxFIFO has been doubled and split into two apertures as follows:

103

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

• Writing to the lower aperture will load 32 bits of data and clear the tag

bit to 0 at the addressed location

• Writing to the higher aperture will load 32 bits of data and set the tag

bit to 1 at the addressed location

• Reading from the lower aperture will return 32 bits of data from the

addressed location

• Reading from the higher aperture will return the tag bit from the

addressed location on data line [0]

Table 122: ETX TxFIFO Address

Physical Address

Access Size

TxFIFO lower aperture

0x8C0_3000 - 0x8C0_37FC

4 bytes

TxFIFO higher aperture

0x8C0_3800 - 0x8C0_3FFC

4 bytes

NOTE: The TxFIFO should never be accessed using PIOs during nor-

mal operation.

7.5.19 ERX Conﬁguration Register

This 23-bit register determines the ERX-specific parameters that control the

operation of the receive DMA channel.

Table 123: ERX Conﬁguration Register Address

Physical Address

Access Size

ERX conﬁguration register

0x8C0_4000

4 bytes

104

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 124: ERX Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Rx_DMA_Enable

When set to 1’, the DMA operation of the

channel is enabled. The load control state

machine will start responding to RX_MAC

requests for data transfer. When cleared to

0, the DMA operation of the channel will

cease as soon as the transfer of the current

frame has ben completed.

R/W

2:1

5:3

Reserved

First_Byte_Offset

Desc_Ring_Size

This ﬁeld determines the offset of the ﬁrst

data byte of the packet within the ﬁrst

double-word of packet data in the RxFIFO

and in the host data buffer.

R/W

8:6

Reserved

10:9

This ﬁeld determines the number of

descriptor entries in the ring. These bits are

encoded as follows:

R/W

00: 32 entries

01: 64 entries

10: 128 entries

11: 256 entries

15:11

22:16

Reserved

Checksum_Start_Offset

Indicates the number of half-words from

the ﬁrst byte of the packet that should be

skipped before the TCP checksum calcula-

tion begins

R/W

7.5.20 ERX Receive Descriptor Pointer

Table 125: ERX Receive Descriptor Pointer Register Address

Physical Address

Access Size

4 bytes

ERX receive descriptor pointer register

0x8C0_4004

105

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 126: ERX Receive Descriptor Pointer Register Deﬁnition

Field

Bits

28:8

7:0

Description

Type

R/W

Base address for the descriptor ring

Displacement for the current descriptor

Note: The receive descriptor pointer must be initialized to a 2K byte-

aligned value after power-on or software reset.

7.5.21 ERX Receive Data Buffer Pointer

This 28-bit loadable counter keeps track of the next DVMA write burst ad-

dress. The counter increments by 1, 2, or 4 (depending on the burst size) after

a DVMA write burst cycle has been executed by the receive DMA engine.

The counter is loaded with the Free_Buffer_Pointer during the descriptor

fetch phase. This counter is used to generate the DVMA write burst address.

Table 127: ERX Receive Data Buffer Pointer Register Address

Physical Address

Access Size

ERX Receive Data Buffer Pointer register

0x8C0_4008

4 bytes

Table 128: ERX Receive Data Buffer Pointer Register Deﬁnition

Field

Bits

Description

Type

27:0

Counter, keeps track of next DVMA write

burst address

7.5.22 ERX RxFIFO Write Pointer

This 9-bit loadable counter points to the next location in the RxFIFO that will

be loaded with data from the RX_MAC. The counter increments by 1 or 2

(depending on SBus configuration) after a word (or double-word) was loaded

into the FIFO. The counter is loaded with the contents of Shadow Write

Pointer, when an “early receive abort” needs to be performed. This counter

generates the “write” address for the RxFIFO memory core.

106

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 129: ERX RxFIFO Write Pointer Register Address

Physical Address

Access Size

ERX RxFIFO Write Pointer register

0x8C0_400C

4 bytes

107

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 130: ERX RxFIFO Write Pointer Register Deﬁnition

Field

Bits

Description

Type

8:0

Counter, points to the next location in RxFIFO

that will receive data from RX_MAC

R/W

7.5.23 ERX RxFIFO Shadow Write Pointer

This nine-bit register points to the first word of the packet that is either cur-

rently being loaded or is about to be loaded into the FIFO. The register is

loaded with the contents of the write pointer after the packet transfer from the

RX_MAC to the FIFO has been completed. This register is used to perform

an early receive abort.

Table 131: ERX RxFIFO Shadow Write Pointer Register Address

Physical Address

Access Size

ERX RxFIFO shadow write pointer register

0x8C0_4010

4 bytes

Table 132: ERX RxFIFO Shadow Write Pointer Register Deﬁnition

Field

Bits

Description

Type

8:0

Points to the ﬁrst word of the packet that is either

currently being loaded or to be loaded into the

FIFO

R/W

7.5.24 ERX RxFIFO Read Pointer

This nine-bit loadable counter points to the next location in the RxFIFO that

will be read from to retrieve packet data that is transferred to the host memo-

ry. The counter increments by 1 or 2 after a word (or double word) was read

from the FIFO. This counter generates the read address for the RxFIFO mem-

ory core.

Table 133: ERX RxFIFO Read Pointer Register Address

Physical Address

Access Size

ERX RxFIFO read pointer register

0x8C0_4014

4 bytes

108

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 134: ERX RxFIFO Read Pointer Register Deﬁnition

Field

Bits

Description

Type

8:0

Counter, points to the next location in

RxFIFO that will be read.

R/W

7.5.25 ERX RxFIFO Packet Counter

This eight-bit up/down counter keeps track of the number of frames that cur-

rently reside in the RxFIFO. The counter increments when a frame is loaded

into the FIFO, and decrements when a frame has been transferred to the host

memory. This counter is used to enable a frame transfer to the host memory.

Table 135: ERX RxFIFO Packet Counter Address

Physical Address

Access Size

ERX RxFIFO packet counter

0x8C0_4018

4 bytes

Table 136: ERX RxFIFO Packet Counter Deﬁnition

Field

Bits

Description

Type

R/W

7:0

Counter, number of frames currently in

RxFIFO

7.5.26 ERX State Machine Register

This 32-bit register provides the current state for all the state machines in

ERX.

Table 137: ERX State Machine Register Address

Physical Address

Access Size

ERX state machine register

0x8C0_401C

4 bytes

109

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 138: ERX State Machine Register Deﬁnition

Field

Bits

4:0

Description

Load control state machine state

FIFO pointer state

Type

6:5

9:7

Checksum state machine state

Reserved

15:10

19:16

23:20

25:24

31:26

Data state machine state

Descriptor state machine state

ERX Memdone counter state

Reserved

7.5.27 ERX RxFIFO

For diagnostic purposes, a PIO path has been provided into the RxFIFO.

When using PIOs, the configuration of the RxFIFO will be 512 × 33bits. In

order to be able to access all the bits in the memory core, the address space of

the RxFIFO has been doubled and split into two apertures as follows:

• Writing to the lower aperture will load 32 bits of data and clear the tag

bit to 0 at the addressed location

• Writing to the higher aperture will load 32 bits of data and set the tag

bit to 1 at the addressed location

• Reading from the lower aperture will return 32 bits of data from the

addressed location

• Reading from the higher aperture will return the tag bit from the

addressed location on data line [0]

Table 139: ERX FxFIFO Address

Physical Address

Access Size

RxFIFO lower aperture

0x8C0_5000 - 0x8C0_57FC

4 bytes

RxFIFO higher aperture

0x8C0_5800 - 0x8C0_5FFC

4 bytes

Note: The RxFIFO should never be accessed using PIOs during nor-

mal operation.

110

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.28 XIF Conﬁguration Register

This 10-bit register determines the parameters that control the operation of

the transceiver interface.

Table 140: XIF Conﬁguration Register Address

Physical Address

Access Size

XIF conﬁguration register

0x8C0_6000

4 bytes

Table 141: XIF Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Tx_Output_Enable

When set to 1, this bit enables the output driv-

ers on the MII transmit bus

R/W

MII_Loopback

This mode of operation implements the inter-

nal loopback for the Ethernet channel. The

entire channel is driven off the system clock,

the MII transmit bus is looped back to the MII

receive bus, and the MII Tx_En signal is

looped back to the MII Rx_Dv input

R/W

MII_Buffer_Enable

Control and external tristate buffer that may

reside on the MII receive data bus.

R/W

SQE_Test_Enable

(Rev 2.1)

When set to 1, this bit enables the signal qual-

ity error test as deﬁned by IEEE 802.3. This

feature is applicable only if a 10Base-T trans-

ceivers is connected to the MII, that

implements this function.

When set to 1, this bit enables the programma-

ble extension of the Rx-to-Tx IPG. In this

mode, the TxMAC will defer during IPG0 and

IPG1 when timing the Rx-to-Tx IPG, and will

not defer during IPG2. When cleared to 0, the

TxMAC will ignore IPG0, defer during IPG1

when timing Rx-to-Tx IPG, and will not defer

during IPG2.

LANCE_Mode

(Rev 2.2)

111

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 141: XIF Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

SQE_Test_Window

(Rev 2.1)

9:5

This ﬁeld deﬁnes the “time window” during

which the MII COL signal should become

asserted, after the completion of the last trans-

mission. This ﬁeld is only meaningful if the

SQE_Test_Enable bit is set to 1.

R/W

IPGO (Rev 2.2)

This ﬁeld deﬁne the value of InterPacketGap0.

This ﬁeld is valid only if the LANCE_Mode is

enabled, and ignored otherwise. The time

interval speciﬁed in this register is in units of

media nibble time.

Default: 0x140.

Note: To ensure proper operation of the hardware, when a loop-back

configuration is entered or exited, a global initialization sequence

should be performed.

7.5.29 TX_MAC Software Reset Command

This one-bit command performs a software reset to the logic in the TX_MAC.

The bit is set to 1 when a programmed I/O write is performed to the defined

address. This bit becomes self-cleared after the command has been executed.

Table 142: TX_MAC Software Reset Command Address

Physical Address

Access Size

TX_MAC software reset command

0x8C0_6208

4 bytes

7.5.30 TX_MAC Conﬁguration Register

This 11-bit register controls the operation of the TX_MAC.

Table 143: TX_MAC Conﬁguration Register Address

Physical Address

Access Size

TX_MAC conﬁguration register

0x8C0_620C

4 bytes

112

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 144: TX_MAC Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

TX_MAC_Enabl

When set to 1, the TX_MAC will start requesting

packet data from the ETX, and the transmit

Ethernet protocol execution will begin. When

cleared to 0, it will force the TX_MAC state

machines to either remain in the idle state, or to

transition to the idle state and stay there at the

completion of an ongoing packet transmission.

R/W

4:1

Reserved

Slow_Down

When set to 1, this bit will cause the TX_MAC to

check for carrier sense before every transmission

on the medium, and for the entire duration of the

IPG. For normal operation this bit should be

cleared to 0.

R/W

Ignore_Collision

No_FCS

When set to 1, this bit will cause the TX_MAC to

ignore collisions on the medium. For normal

operation this bit should be cleared to 0.

R/W

When set to 1, this bit will cause the TX_MAC

not to generate the CRC for transmitted frame.

For normal operation this bit should be cleared to

No_Backoff

When this bit is set to ‘1’, the backoff algorithm

in the Protocol Engine is disabled. The TX_MAC

will not back off after a transmission attempt that

collided on the medium. Effectively the random

number chosen by the backoff algorithm is ﬁxed

to ‘0’. For normal operation this bit should be

cleared to ‘0’

R/W

Full_Duplex

When this bit is set to 1, the CSMA/CD protocol

is modiﬁed such that the TX_MAC will never

give up on a frame transmission.In effect, no limit

will exist on transmission attempts. If the backoff

algorithm reaches the attempts_limit, it will clear

the attempts_counter and continue trying to

transmit the frame until it is successfully trans-

mitted on the medium. For normal operation it is

recommended that this bit is set to 1.

R/W

Never_Give_Up

When this bit is set to 1, the CSMA/CD protocol

is modiﬁed such that the TX_MAC will never

give up on a frame transmission. In effect, no

limit will exist on transmission attempts. If the

backoff algorithm reaches the attempts_limit, it

will clear the attempts_counter and continue try-

ing to transmit the frame until it is successfully

transmitted on the medium. For normal operation

it is recommended that this bit is set to 1.

R/W

113

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Note: To ensure proper operation of the TX_MAC, the TX_MAC_En

bit must always be cleared to 0 and a delay imposed before a PIO write

to any of the other bits in the TX_MAC Configuration register or any

of the MAC parameters registers is performed. The MAC parameters’

registers are IPG1, IPG2, AttemptLimit, SlotTime, PA_Size,

PA_Pattern, SFD_Pattern, JamSize, TxMinFrameSize, and TxMax-

FrameSize.

The amount of delay required will depend on the time required to trans-

mit a maximum size frame, and is thus dependent on the value

programmed into the TxMaxFrameSize register and the data rate on

the medium. For a standard 1518-byte frame on a 100-Mbps network,

the delay would be 125 msec. To avoid the requirement for a variable

time delay, the TX_MAC_En bit may be polled, and when this bit

reads back as a 0, all the registers mentioned above may be written,

including all the other bits in the configuration register.

7.5.31 TX_MAC InterPacketGap1 Register

This eight-bit register defines the first 2/3 portion of the InterPacketGap,

which is timed by the TX_MAC before each frame’s transmission is initiated.

For back-to-back transmissions, this value is added to the value in the

InterPacketGap2 register, and during the entire period the CarrierSense input

signal is ignored by the TX_MAC. For a reception followed by a transmis-

sion, the TX_MAC will monitor the CarrierSense input signal during the time

interval specified in this register and will respond to it, but will ignore it dur-

ing the time interval specified in the InterPacketGap2 register. The time in-

terval specified in this register is in units of media byte time.

Table 145: TX_MAC InterPacketGap1 Register Address

Physical Address

Access Size

InterPacketGap1 register

0x8C0_6210

4 bytes

Table 146: TX_MAC InterPacketGap1 Register Deﬁnition

Field

Bits

Description

Type

7:0

First 2/3 portion of IPG, timed by TX_MAC

before frame transmission in initiated

R/W

Default value: 0x08.

114

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.32 TX_MAC InterPacketGap2 Register

This eight-bit register defines the second 1/3 portion of the InterPacketGap

parameter.

Table 147: TX_MAC InterPacketGap2 Register Address

Physical Address

Access Size

InterPacketGap2 register

0x8C0_6214

4 bytes

Table 148: TX_MAC InterPacketGap2 Register Deﬁnition

Field

Bits

Description

Type

R/W

7:0

Second 1/3 portion of IPG

Default value: 0x04.

7.5.33 TX_MAC AttemptLimit Register

Table 149: TX_MAC AttemptLimit Register Address

Physical Address

Access Size

4 bytes

AttemptLimit register

0x8C0_6218

Table 150: TX_MAC AttemptLimit Register Deﬁnition

Field

Bits

Description

Type

AttemptLimit

7:0

Speciﬁes number of attempts TX_MAC will

make to transmit a frame before giving up on

transmission.

R/W

Default value: 0x10.

7.5.34 TX_MAC SlotTime Register

Table 151: TX_MAC SlotTime Register Address

SlotTime register

Physical Address

Access Size

4 bytes

0x8C0_621C

115

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 152: TX_MAC SlotTime Register Deﬁnition

Field

SlotTime

Bits

Description

Type

7:0

Speciﬁes the slot time parameter in units of

media byte time. Deﬁnes the physical span

of the network.

R/W

Default value: 0x40.

7.5.35 TX_MAC PA Size Register

Table 153: TX_MAC PA Size Register Address

PA size register

Physical Address

Access Size

4 bytes

0x8C0_6220

Table 154: TX_MAC PA Size Register Deﬁnition

Field

PA size

Bits

Description

Type

7:0

Speciﬁes the number of PreAmble bytes that will

be transmitted at the beginning of each frame. The

greater.

R/W

Default value: 0x07.

7.5.36 TX_MAC PA Pattern Register

Table 155: TX_MAC PA Pattern Register Address

Physical Address

Access Size

PA pattern register

0x8C0_6224

4 bytes

Table 156: TX_MAC PA Pattern Register Deﬁnition

Field

PA pattern

Bits

Description

Type

7:0

Speciﬁes the bit pattern of the PreAmble bytes

that are transmitted at the beginning of each

frame. The most signiﬁcant bit of this register

is transmitted and received ﬁrst.

R/W

Default value: 0xAA.

116

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.37 TX_MAC SFD Pattern Register

Table 157: TX_MAC SFD Pattern Register Address

Physical Address

Access Size

SFD pattern register

0x8C0_6228

4 bytes

Table 158: TX_MAC SFD Pattern Register Deﬁnition

Field

Bits

Description

Type

SFD pattern

7:0

Speciﬁes the bit pattern of the start of frame

delimiter bytes that are transmitted at the begin-

ning of each frame, after the preamble. The most

signiﬁcant bit of this register will be transmitted

and received ﬁrst.

R/W

Default value: 0xAB

7.5.38 TX_MAC JamSize Register

Table 159: TX_MAC JamSize Register Address

Physical Address

Access Size

4 bytes

JamSize register

0x8C0_622C

Table 160: TX_MAC JamSize Register Deﬁnition

Field

JamSize

Bits

Description

Type

7:0

Speciﬁes the number of bytes to be transmitted

by the TX_MAC after detecting a collision on

the media.

R/W

Default value: 0x04.

7.5.39 TX_MAC TxMaxFrameSize Register

Table 161: TX_MAC TxMaxFrameSize Register Address

Physical Address

Access Size

4 bytes

TxMaxFrameSize register

0x8C0_6230

117

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 162: TX_MAC TxMaxFrameSize Register Deﬁnition

Field

Bits

Description

Type

TxMaxFrameSize

15:0

Speciﬁes the maximum number of bytes

that the TX_MAC will transmit for any

frame on the media.

R/W

Default value: 0x05EE.

7.5.40 TX_MAC TxMinFrameSize Register

Table 163: TX_MAC TxMinFrameSize Register Address

Physical Address

Access Size

4 bytes

TxMinFrameSize register

0x8C0_6234

Table 164: TX_MAC TxMinFrameSize Register Deﬁnition

Field

Bits

Description

Type

TxMinFrameSize

7:0

Speciﬁes the minimum number of bytes that

the TX_MAC will transmit for any frame on

the media.

R/W

Default value: 0x40

7.5.41 TX_MAC PeakAttempts Register

Table 165: TX_MAC PeakAttempts Register Address

Physical Address

Access Size

4 bytes

PeakAttempts register

0x8C0_6238

Table 166: TX_MAC PeakAttempts Register Deﬁnition

Field

Bits

Description

Type

PeakAttempts

7:0

Indicates the highest number of collisions per

successfully transmitted frame, that have

occurred since this register was last read.The

maximum value this register can attain corre-

sponds to the value in the AttemptLimit

cally be cleared to 0 after it is read.

118

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.42 TX_MAC Defer Timer

Table 167: TX_MAC Defer Timer Address

Defer timer

Physical Address

Access Size

0x8C0_623C

4 bytes

Table 168: TX_MAC Defer Timer Deﬁnition

Field

Bits

Description

Type

Defer timer

15:0

Loadable timer increments when the TX_MAC is

deferring to trafﬁc on the network while it is

attempting to transmit a frame. The time base for the

timer is the media byte clock divided by 256. Thus,

on a 10-Mbps network the timer ticks are 200 msec,

and on a 100-Mbps network the timer ticks are 20

msec.

R/W

7.5.43 TX_MAC Normal Collision Counter

Table 169: TX_MAC Normal Collision Counter Address

Physical Address

Access Size

Normal collision counter

0x8C0_6240

4 bytes

Table 170: TX_MAC Normal Collision Counter Deﬁnition

Field

Bits

Description

Type

Normal collision counter

15:0

Loadable counter, increments for every

frame transmission attempt that experi-

ences a collision.

R/W

7.5.44 TX_MAC First Successful Collision Counter

Table 171: TX_MAC First Successful Collision Counter Address

Physical Address

Access Size

4 bytes

First successful collision counter

0x8C0_6244

119

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 172: TX_MAC First Successful Collision Counter Deﬁnition

Field

Bits

Description

Type

First successful collision

counter

15:0

Loadable counter increments for every

frame transmission that collided on the

ﬁrst attempt, but succeeded on the second

attempt.

R/W

7.5.45 TX_MAC Excessive Collision Counter

Table 173: TX_MAC Excessive Collision Counter Address

Physical Address

Access Size

4 bytes

Excessive collision counter

0x8C0_6248

Table 174: TX_MAC Excessive Collision Counter Deﬁnition

Field

Bits

Description

Type

Excessive collision counter

7:0

Loadable counter increments for every

transmit frame that has exceeded the

AttemptLimit. It indicates the number

of frames that the TX_MAC has given

up transmitting due to excessive amount

of trafﬁc on the network.

R/W

7.5.46 TX_MAC Late Collision Counter

This eight-bit loadable counter increments for every transmit frame that has

experienced a late collision. It indicates the number of frames that the

TX_MAC has given up transmitting due to collisions that occurred after the

TxMinFrameSize number of bytes have already been transmitted. Usually

this is an indication that there is at least one station on the network that vio-

lates the maximum span of the network.

Table 175: TX_MAC Late Collision Counter Address

Physical Address

Access Size

Late collision counter

0x8C0_624C

4 bytes

120

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 176: TX_MAC Late Collision Counter Deﬁnition

Field

Bits

Description

Type

Late collision counter

7:0

Loadable counter increments for every

transmit frame that has experienced a late

collision.

R/W

7.5.47 TX_MAC Random Number Seed Register

This 10-bit register is used as a seed for the random number generator in the

backoff algorithm. The register has significance only after power-on reset,

and it should be programmed with a random value which has a high likeli-

hood of being unique for each MAC attached to a network segment (10 LSB

of the MAC address). During normal operation, the register contents are up-

dated constantly by the hardware, and a PIO read from this register will return

an unpredictable result.

Table 177: TX_MAC Random Number Seed Register Address

Physical Address

Access Size

Random number seed register

0x8C0_6250

4 bytes

Table 178: TX_MAC Random Number Seed Register Deﬁnition

Field

Bits

Description

Type

Random number seed

9:0

Seed for the random number generator in

the backoff algorithm.

R/W

7.5.48 TX_MAC State Machine Register

This eight-bit register provides the current state for all the state machines in

TX_MAC.

Table 179: TX_MAC State Machine Register Address

Physical Address

Access Size

TX_MAC state machine register

0x8C0_6254

4 bytes

121

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 180: TX_MAC State Machine Register Deﬁnition

Field

Bits

3:0

Description

TLM state machine state

Type

7:4

Encapsulation state machine state

7.5.49 RX_MAC Software Reset Command

This 16-bit command performs a software reset to the logic in the RX_MAC.

The defined address must be written with the value of 0x0000.

Table 181: RX_MAC Software Reset Command Address

Physical Address

Access Size

RX_MAC software reset command

0x8C0_6308

4 bytes

7.5.50 RX_MAC Conﬁguration Register

This 13-bit register controls the operation of the RX_MAC.

Table 182: RX_MAC Conﬁguration Register Address

Physical Address

Access Size

RX_MAC conﬁguration register

0x8C0_630C

4 bytes

Table 183: RX_MAC Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Rx_MAC_Enable

When set to 1, the RX_MAC will start

requesting packet data transfers to the

ERX, and the receive Ethernet protocol

execution will begin. When cleared to 0, it

will force the RX_MAC state machines to

either remain in the idle state, or to transi-

tion to the idle state and stay there.

R/W

4:1

Reserved

Strip_Pad

When set to 1, this bit will cause the

RX_MAC to strip the pad bytes of the

receive frames.

R/W

Promiscuous_Mode

When set to 1, this bit will cause the

RX_MAC to accept all valid frames from

the network, regardless of the contents of

the DA ﬁeld of a frame.

R/W

122

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 183: RX_MAC Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

Err_Check_Disable

When set to 1, this bit will cause the

RX_MAC to receive frames from the net-

work without checking for CRC, framing,

or length errors.

R/W

No_CRC_Strip

When set to 1, this bit will cause the

RX_MAC not to strip the last four bytes

(FCS) of a received frame.

R/W

Reject_My_Frame

Promisc_Group_Mode

When set to 1, this bit will cause the

RX_MAC to discard frames with the SA

ﬁeld matching the station’s MAC address.

When set to 1, this bit will cause the

RX_MAC to accept all valid frames from

the network that have the group bit in the

DA ﬁeld set to 1.

Hash_Filter_Enable

When set to 1, the RX_MAC will use the

hash table to ﬁlter multicast addresses.

R/W

Address_Filter_Enable

When set to 1, the RX_MAC will use the

address ﬁltering registers to ﬁlter incoming

frames.

Note:

To ensure proper operation of the RX_MAC, the RX_MAC_En bit

must always be cleared to 0 and a delay of 3.2 msec imposed before a

PIO write to any of the other bits in the RX_MAC configuration regis-

ter or any of the MAC parameters’ registers is performed. The

RX_MAC parameters’ registers are: RxMinFrameSize, RxMaxFrame-

Size, and the MAC Address registers. To avoid the requirement for a

fixed time delay, the RX_MAC_En bit may be polled, and when this

bit reads back as a 0, all the registers mentioned above may be written,

including other bits in the configuration register.

To ensure proper operation of the RX_MAC, the Hash_Filter_Enable

bit in the RX_MAC configuration register must always be cleared to 0

and a delay of 3.2 msec imposed before a PIO write to any of the hash

table registers is performed. To avoid the requirement for a fixed time

delay, the Hash_Filter_Enable bit may be polled, and when this bit

reads back as a 0, all the registers mentioned above may be written.

To ensure proper operation of the RX_MAC, the

Address_Filter_Enable bit in the RX_MAC configuration register

must always be cleared to 0 and a delay of 3.2 msec imposed before a

PIO write to any of the address filter registers is performed. To avoid

the requirement for a fixed time delay, the Address_Filter_Enable bit

123

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

may be polled, and when this bit reads back as a 0, all the registers

mentioned above may be written.

7.5.51 RX_MAC RxMaxFrameSize Register

Table 184: RX_MAC RxMaxFrameSize Register Address

Physical Address

Access Size

RX_MAC RxMaxFrameSize register

0x8C0_6310

4 bytes

Table 185: RX_MAC RxMaxFrameSize Register Deﬁnition

Field

Bits

Description

Type

12:0

Speciﬁes the maximum number of bytes in

a frame that the RX_MAC will expect to

see before it will recognize the frame to be

invalid.

R/W

Default value: 0x05EE.

7.5.52 RX_MAC RxMinFrameSize Register

Table 186: RX_MAC RxMinFrameSize Register Address

Physical Address

Access Size

4 bytes

RX_MAC RxMinFrameSize register

0x8C0_6314

Table 187: RX_MAC RxMinFrameSize Register Deﬁnition

Field

Bits

Description

Type

7:0

Speciﬁes the minimum number of bytes in

a frame that the RX_MAC will expect to

see before it will recognize the frame to be

valid.

R/W

Default value: 0x40.

124

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.53 RX_MAC MAC Address 2 Register

Table 188: RX_MAC MAC Address 2 Register Address

Physical Address

Access Size

RX_MAC MAC Address2 register

0x8C0_6318

4 bytes

125

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 189: RX_MAC MAC Address 2 Register Deﬁnition

Field

Bits

Description

Type

15:0

16 most signiﬁcant bits of the MAC address.

These bits will be compared against bits

[47:32] of the DA ﬁeld in every frame that

arrives from the network.

R/W

7.5.54 RX_MAC MAC Address 1 Register

Table 190: RX_MAC MAC Address 1 Register Address

Physical Address

Access Size

4 bytes

RX_MAC MAC Address1 register

0x8C0_631C

Table 191: RX_MAC MAC Address 1 Register Deﬁnition

Field

Bits

Description

Type

R/W

15:0

Contains bits [31:16] of the MAC address.

These bits will be compared against bits

[31:16] of the DA ﬁeld in every frame that

arrives from the network.

7.5.55 RX_MAC MAC Address 0 Register

Table 192: RX_MAC MAC Address 0 Register Address

Physical Address

Access Size

4 bytes

RX_MAC MAC Address0 register

0x8C0_6320

Table 193: RX_MAC MAC Address 0 Register Deﬁnition

Field

Bits

Description

Type

15:0

Contains the 16 least signiﬁcant bits of the

MAC address. These bits will be compared

against bits [15:0] of the DA ﬁeld in every

frame that arrives from the network.

R/W

126

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.56 RX_MAC Receive Frame Counter

Table 194: RX_MAC Receive Frame Counter Address

Physical Address

Access Size

RX_MAC receive frame counter

0x8C0_6324

4 bytes

Table 195: RX_MAC Receive Frame Counter Deﬁnition

Field

Bits

Description

Type

15:0

Counter that increments after a valid frame

has been received from the network

R/W

7.5.57 RX_MAC Length Error Counter

Table 196: RX_MAC Length Error Counter Address

Physical Address

Access Size

4 bytes

RX_MAC length error counter

0x8C0_6328

Table 197: RX_MAC Length Error Counter Deﬁnition

Field

Bits

Description

Type

7:0

Loadable counter increments when a frame,

whose length is greater than the value pro-

grammed in the RxMaxFrameSize register,

is received from the network.

R/W

7.5.58 RX_MAC Alignment Error Counter

This eight-bit loadable counter increments when an alignment error was de-

tected in a receive frame. An alignment error is reported when a receive frame

fails the CRC checking algorithm, and the frame does not contain an integer

number of bytes (i.,e., the frame size in bits modulo 8 is not equal to 0).

Table 198: RX_MAC Alignment Error Counter Address

Physical Address

Access Size

RX_MAC alignment error counter

0x8C0_632C

4 bytes

127

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 199: RX_MAC Alignment Error Counter Deﬁnition

Field

Bits

Description

Type

7:0

Loadable counter increments when an

alignment error was detected in a receive

frame

R/W

7.5.59 RX_MAC FCS Error Counter

Table 200: RX_MAC FCS Error Counter Address

Physical Address

Access Size

4 bytes

RX_MAC FCS error counter

0x8C0_6330

Table 201: RX_MAC FCS Error Counter Deﬁnition

Field

Bits

Description

Type

7:0

Loadable counter increments when a

receive frame failed the CRC checking

R/W

algorithm, but it did not cause an alignment

error.

7.5.60 RX_MAC State Machine Register

This seven-bit register provides the current state for all the state machines in

the RX_MAC.

Table 202: RX_MAC State Machine Register Address

Physical Address

Access Size

RX_MAC state machine register

0x8C0_6334

4 bytes

Table 203: RX_MAC State Machine Register Deﬁnition

Field

Bits

4:0

Description

Receive protocol state machine state

Pad state machine state

Type

6:5

128

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.61 RX_MAC Rx Code Violation Counter

Table 204: RX_MAC Rx Code Violation Error Counter Address

Physical Address

Access Size

RX_MAC Rx code violation error counter

0x8C0_6338

4 bytes

Table 205: RX_MAC Rx Code Violation Error Counter Deﬁnition

Field

Bits

Description

Type

7:0

Loadable counter, increments when an

Rx_Err indication is generated by the

XCVR over the MII, while a frame is being

received. This indication is generated by the

transceiver when it detects an invalid code in

the received data stream. A receive code vio-

lation is not counted as an FCS or an

alignment error.

R/W

7.5.62 RX_MAC Hash Table 3 Register

Table 206: RX_MAC Hash Table 3 Register Address

Physical Address

Access Size

4 bytes

RX_MAC hash table 3 register

0x8C0_6340

Table 207: RX_MAC Hash Table 3 Register Deﬁnition

Field

Bits

Description

Type

15:0

Contains bits [63:48] of the hash table.

R/W

7.5.63 RX_MAC Hash Table 2 Register

Table 208: RX_MAC Hash Table 2 Register Address

Physical Address

Access Size

RX_MAC hash table 2 register

0x8C0_6344

4 bytes

129

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 209: RX_MAC Hash Table 2 Register Deﬁnition

Field

Bits

Description

Type

15:0

Contains bits [47:32] of the hash table.

R/W

7.5.64 RX_MAC Hash Table 1 Register

Table 210: RX_MAC Hash Table 1 Register Address

Physical Address

Access Size

4 bytes

RX_MAC hash table 1 register

0x8C0_6348

Table 211: RX_MAC Hash Table 1 Register Deﬁnition

Field

Bits

Description

Type

15:0

Contains bits [31:16] of the hash table.

R/W

7.5.65 RX_MAC Hash Table 0 Register

Table 212: RX_MAC Hash Table 0 Register Address

Physical Address

Access Size

RX_MAC hash table 0 register

0x8C0_634C

4 bytes

Table 213: RX_MAC Hash Table 0 Register Deﬁnition

Field

Bits

Description

Type

R/W

15:0

Contains bits [15:0] of the hash table.

7.5.66 RX_MAC Address Filter 2 Register

Table 214: RX_MAC Address Filter 2 Register Address

Physical Address

Access Size

RX_MAC address ﬁlter 2 register

0x8C0_6350

4 bytes

130

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 215: RX_MAC Address Filter 2 Register Deﬁnition

Field

Bits

Description

Contains bits [47:32] of the address ﬁlter.

Type

15:0

R/W

7.5.67 RX_MAC Address Filter 1 Register

Table 216: RX_MAC Address Filter 1 Register Address

Physical Address

Access Size

4 bytes

RX_MAC address ﬁlter 1 register

0x8C0_6354

Table 217: RX_MAC Address Filter 1 Register Deﬁnition

Field

Bits

Description

Contains bits [31:16] of the address ﬁlter.

Type

15:0

R/W

7.5.68 RX_MAC Address Filter 0 Register

Table 218: RX_MAC Address Filter 0 Register Address

Physical Address

Access Size

4 bytes

RX_MAC address ﬁlter 0 register

0x8C0_6358

Table 219: RX_MAC Address Filter 0 Register Deﬁnition

Field

Bits

Description

Type

R/W

15:0

Contains bits [15:0] of the address ﬁlter.

7.5.69 RX_MAC Address Filter Mask Register

Table 220: RX_MAC Address Filter Mask Register Address

Physical Address

Access Size

4 bytes

RX_MAC address ﬁlter mask register

0x8C0_635C

131

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 221: RX_MAC Address Filter Mask Register Deﬁnition

Field

Bits

Description

Type

11:0

Contains 12 bit nibble mask for the Address Filter.

R/W

7.5.70 MIF Bit-Bang Clock

This one-bit register is used to generate the MDC clock waveform on the MII

management interface when the MIF is programmed in the Bit-Bang Mode.

Writing a 1 after a 0 into this register will create a rising edge on the MDC,

while writing a 0 after a 1 will create a falling edge. For every bit that is trans-

ferred on the management interface, both edges have to be generated.

Table 222: MIF Bit-Bang Clock Address

Physical Address

Access Size

MIF bit-bang clock

0x8C0_7000

4 bytes

7.5.71 MIF Bit-Bang Data

This one-bit register is used to generate the outgoing data (MDO) on the MII

management interface when the MIF is programmed in the Bit-Bang Mode.

The data will be steered to the appropriate MDIO based on the state of the

PHY_Select bit in the MIF configuration register.

Table 223: MIF Bit-Bang Data Address

Physical Address

Access Size

MIF bit-bang data

0x8C0_7004

4 bytes

7.5.72 MIF Bit-Bang Output Enable

This one-bit register is used to enable (1) and disable (0) the I-directional

driver on the MII management interface when the MIF is programmed in the

Bit-Bang Mode. The MDIO should be enabled when data bits are transferred

from the MIF to the transceiver, and it should be disabled when the interface

is idle or when data bits are transferred from the transceiver to the MIF (data

portion of a read instruction). Only one MDIO will be enabled at a given time,

depending on the state of the PHY_Select bit in the MIF configuration regis-

ter.

132

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 224: MIF Bit-Bang Output Enable Address

Physical Address

Access Size

MIF bit-bang output enable

0x8C0_7008

4 bytes

7.5.73 MIF Frame/Output Register

This 32-bit register serves as an “instruction register” when the MIF is pro-

grammed in the frame mode. In order to execute a read/write operation

from/to a transceiver register, the software has to load this register with a val-

id instruction, as per the IEEE 802.3u MII specification. After issuing an in-

struction, the software has to poll this register to check for instruction

execution completion. During a read operation, this register will also contain

the 16-bit data that was returned by the transceiver.

Table 225: MIF Frame/Output Register Address

Physical Address

Access Size

MIF frame/output register

0x8C0_700C

4 bytes

Table 226: MIF Frame/Output Register Deﬁnition

Field

DATA

Bits

Description

Type

15:0

Instruction payload. When issuing an instruction, this

ﬁeld should be loaded with the 16-bit data to be written

into a transceiver register for a write, and is a don’t care

for a read. When polling for completion, this ﬁeld is a

don’t care for a write, and contains the 16-bit data

returned by the transceiver for a read (if the valid bit is

set).

R/W

TA_LSB

TA_MSB

Turn around, least signiﬁcant bit. When issuing an

instruction, this bit should always be loaded with a 0.

When polling for completion, this bit serves as a valid

bit. When this bit is set to 1, the instruction execution

has been completed.

R/W

Turn around, most signiﬁcant bit. When issuing an

instruction, this bit should always be loaded with a 1.

When polling for completion, this bit is always a don’t

care.

133

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 226: MIF Frame/Output Register Deﬁnition

Field

Bits

Description

Type

REGAD

22:18

R/W

When issuing an instruction, this ﬁeld should be loaded

with the address of the register that is to be read/

written.

When polling for completion, this ﬁeld is always a don’t

care.

PHYAD

27:23

29:28

31:30

PHY ADdress.

R/W

When issuing an instruction, this ﬁeld should be loaded

with the XCVR address.

When polling for completion, this ﬁeld is always a don’t

care.

OPcode.

When issuing an instruction, this ﬁeld should be loaded

with 01 for a write and with 10 for a read.

When polling for completion, this ﬁeld is always a don’t

care.

STart of frame.

When issuing an instruction, this ﬁeld should always be

loaded with a 01.

When polling for completion, this ﬁeld is always a don’t

care.

7.5.74 MIF Conﬁguration Register

This 15-bit register controls the operation of the MIF.

Table 227: MIF Conﬁguration Register Address

Physical Address

Access Size

MIF conﬁguration register

0x8C0_7010

4 bytes

134

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 228: MIF Conﬁguration Register Deﬁnition

Field

Bits

Description

Type

PHY_Select

The MIF implements two independent manage-

ment interfaces for two separate transceivers. Only

one transceiver can be used at a given time. This bit

determines which transceiver is currently in use.

When cleared to 0, MDIO_0 is selected. Went set

to 1, MDIO_1 is selected.

R/W

Poll_Enable

BB_Mode

When set to 1, this bit enables the polling mecha-

nism. If this bit is set to 1, the BB_Mode should be

cleared to 0.

R/W

This bit determines the mode of operation of the

MIF. When set to 1, the Bit-Bang Mode is selected.

When cleared to 0, the frame mode will be used.

Poll_Reg_Addr

7:3

This ﬁeld determines the register address in the

transceiver that will be polled by the polling mech-

anism in the MIF. It is meaningful only if the

Poll_Enable bit is set to 1.

MDI_0

This read-only bit is dual purpose.When the

MDIO_0 interface is idle, this bit will indicate

whether a transceiver is connected to this line. If

this bit reads as 1, the transceiver is connected.

When the MIF is communicating with a trans-

ceiver that is hooked up to MDIO_0 in the Bit-

Bang Mode, this bit will indicate the incoming bit

stream during a read operation

MDI_1

This read-only bit is dual purpose. When the

MDIO_1 interface is idle, this bit will indicate

whether a transceiver is connected to this line. If

this bit reads as 1, the transceiver is connected.

When the MIF is communicating with a trans-

ceiver that is hooked up to MDIO_1 in the Bit-

Bang Mode, this bit will indicate the incoming bit

stream during a read operation

Poll_Phy_Addr

14:10

This ﬁeld determines the transceiver address to be

polled

R/W

7.5.75 MIF Mask Register

This 16-bit register is used to determine which bits in the poll status portion

of the MIF status register will cause an interrupt. If a mask bit is cleared to 0,

the corresponding bit of the poll status will generate the MIF interrupt when

set.

135

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 229: MIF Mask Register Address

Physical Address

Access Size

MIF mask register

0x8C0_7014

4 bytes

Table 230: MIF Mask Register Deﬁnition

Field

Bits

Description

Type

15:0

Interrupt mask for Poll_Status bits in MIF

status register

R/W

Default value: 0xFFFF.

7.5.76 MIF Status Register

This 32-bit register is used in conjunction with the poll mode in the MIF. It

contains two portions: poll data and poll status. The poll data field will always

contain the latest and greatest image update of the XCVR register that is being

polled, while the poll status field will indicate which bits in the poll data field

have changed since the MIF status register was last read. The poll status field

is auto-cleared after being read.

Table 231: MIF Status Register Address

Physical Address

Access Size

MIF status register

0x8C0_7018

4 bytes

Table 232: MIF Status Register Deﬁnition

Field

Bits

Description

Type

Poll_Status

15:0

Indicates which bit in poll data ﬁeld has changed

since last read

Poll_Data

31:16

Latest image of XCVR register that is being

polled

136

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

7.5.77 MIF State Machine Register

This nine-bit register provides the current state for all the state machines in

the MIF.

Table 233: MIF State Machine Register Address

Physical Address

Access Size

MIF state machine register

0x8C0_701C

4 bytes

Table 234: MIF State Machine Register Deﬁnition

Field

Bits

2:0

4:3

6:5

8:7

Description

Control state machine state

Reserved

Type

Execution state machine state

Reserved

137

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

PIN ASSIGNMENTS

8.1 Pin Assignments

The Table 235 describes the pin assignments for the 240-pin PQFP FEPS

package.

Table 235: STP2002QFP Pin Assignments

Pin No.

Signal Name

PP_STB

Dual Function (FAS366 Test Mode Only)

PP_AFXN

PP_ERROR

MODE

I_SCSI_DACKN

I_SCSI_RESETN

JTAG_TDI

JTAG_RST

JTAG_CLK

JTAG_TMS

VSS_IO

JTAG_TDO

STOP_CLK

ENET_CRS

VDD_IO

I_SCSI_MODE0

I_SCSI_MODE1

ENET_COL

VSS_IO

ENET_TXD[3]

ENET_TXD[2]

VSS_IO

ENET_TXD[1]

ENET_TXD[0]

ENET_TX_EN

VSS_IO

ENET_TX_CLK

ENET_TX_CLKO

VDD_IO

ENET_RX_ER

ENET_RX_CLK

I_SCSI_A1

I_SCSI_CSN

138

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

Signal Name

ENET_RX_DV

Dual Function (FAS366 Test Mode Only)

I_SCSI_A0

I_SCSI_A2

ENET_RXD[0]

VSS_CORE

ENET_RXD[1]

VDD_CORE

ENET_RXD[2]

ENET_RXD[3]

VSS_IO

I_SCSI_A3

I_SCSI_RDN

I_SCSI_WRN

ENET_BUFFER_EN_0

ENET_MDC

ENET_MDIO0

VDD_IO

ENET_MDIO1

VSS_IO

SCSI_D[11]

SCSI_D[10]

SCSI_D[9]

VSS_IO

SCSI_D[8]

SCSI_IO

SCSI_REQ

VSS_IO

SCSI_CD

SCSI_SEL

SCSI_MSG

VSS_IO

SCSI_RST

SCSI_ACK

SCSI_BSY

VSS_IO

SCSI_ATN

SCSI_SDP[0]

SCSI_D[7]

VSS_IO

139

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

Signal Name

SCSI_D[6]

Dual Function (FAS366 Test Mode Only)

SCSI_D[5]

SCSI_D[4]

VSS_IO

SCSI_D[3]

SCSI_D[2]

SCSI_D[1]

VSS_IO

SCSI_D[0]

SCSI_SDP[1]

SCSI_D[15]

VSS_IO

SCSI_D[14]

SCSI_D[13]

SCSI_D[12]

VSS_IO

SCSI_XTAL1

SCSI_XTAL2

VDD_IO

Resereved

VSS_IO

POD

CLK_10M

VSS_IO

SB_SC_INT

SB_ET_INT

SB_PP_INT

VSS_IO

SB_CLK

VDD_IO

VDD_CORE

SB_BR

VSS_CORE

VSS_IO

140

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

Signal Name

SB_SEL

Dual Function (FAS366 Test Mode Only)

SB_AS

SB_D[0]

VDD_IO

SB_D[1]

VSS_IO

SB_D[2]

SB_D[3]

VSS_IO

SB_D[4]

SB_D[5]

VDD_IO

SB_D[6]

VSS_IO

SB_D[7]

SB_D[8]

VSS_IO

SB_D[9]

SB_D[10]

VSS_IO

SB_D[11]

VDD_IO

SB_D[12]

SB_D[13]

SB_BG

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

IO_SCSI_DB[8]

IO_SCSI_DB[9]

IO_SCSI_DB[10]

IO_SCSI_DB[11]

IO_SCSI_DB[12]

IO_SCSI_DB[13]

VSS_IO

SB_D[14]

SB_D[15]

VSS_IO

SB_D[16]

VDD_IO

SB_D[17]

VSS_IO

SB_D[18]

IO_SCSI_DB[14]

141

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

Signal Name

SB_D[19]

Dual Function (FAS366 Test Mode Only)

SB_D[20]

VSS_IO

SB_D[21]

VDD_IO

SB_D[22]

VSS_IO

SB_D[23]

SB_D[24]

VSS_IO

SB_ACK[0]

SB_ACK[1]

VDD_IO

SB_ACK[2]

VSS_IO

SB_D[25]

VDD_CORE

SB_D[26]

VSS_IO

IO_SCSI_DBP1

SB_D[27]

VSS_CORE

SB_D[28]

VSS_IO

SB_D[29]

VDD_IO

SB_D[30]

SB_D[31]

VSS_IO

SB_SIZ[2]

SB_SIZ[1]

VSS_IO

IO_SCSI_DB[07]

IO_SCSI_DB[06]

SB_SIZ[0]

VDD_IO

SB_RD

IO_SCSI_DB[05]

142

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

Signal Name

VSS_IO

Dual Function (FAS366 Test Mode Only)

SB_PA[0]

SB_PA[1]

SB_PA[2]

VSS_IO

IO_SCSI_DB[04]

IO_SCSI_DB[03]

IO_SCSI_DB[02]

SB_PA[3]

SB_PA[4]

VSS_IO

IO_SCSI_DB[01]

IO_SCSI_DB[00]

SB_PA[5]

VDD_IO

SB_LERR

SB_PA[6]

VSS_IO

IO_SCSI_DBP0

SB_PA[7]

SB_PA[8]

VSS_IO

SB_PA[9]

VDD_IO

SB_PA[10]

VSS_IO

SB_PA[11]

SB_PA[12]

VSS_IO

SB_PA[13]

VDD_IO

SB_PA[14]

SB_PA[15]

VSS_IO

SB_PA[16]

SB_PA[17]

VSS_IO

SB_PA[18]

VDD_IO

SB_PA[19]

143

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

Signal Name

Dual Function (FAS366 Test Mode Only)

SB_PA[20]

SB_PA[21]

SB_PA[22]

VSS_IO

SB_PA[23]

VDD_IO

SB_PA[24]

VSS_IO

SB_PA[25]

VDD_CORE

SB_PA[26]

VSS_IO

VSS_CORE

SB_PA[27]

SB_DATPAR

RESET

I_SCSI_PAUSE

ID_CS

PP_SLCT

PP_PE

I_SCSI_DBWRN

I_SCSI_DBRDN

VDD_IO

PP_BSYDIR

VSS_IO

PP_BSY

PP_ACKDIR

PP_ACK

PP_DDIR

PP_D[7]

VSS_IO

PP_D[6]

PP_D[5]

VDD_IO

PP_D[4]

PP_D[3]

144

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Table 235: STP2002QFP Pin Assignments

Pin No.

232

Signal Name

PP_D[2]

Dual Function (FAS366 Test Mode Only)

233

VSS_IO

234

PP_D[1]

235

PP_D[0]

236

PP_SLCT_IN

PP_INIT

237

238

VDD_IO

PP_DS_DIR

VSS_IO

239

240

145

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

ERRATA

9.1 Description of Errata in FEPS Rev 2.2

The following are some known problems and workarounds for Rev 2.2. of the

FEPS. The device driver for the SCSI channel has software workarounds for

all of these problems.

9.1.1 SCSI DVMA/Channel Engine (CE)

9.1.1.1 SCSI CE Byte Count Gets Frozen

During SCSI write, under a set of conditions, 1 byte could get stuck in the

SCSI CE. The symptom, root cause, and workaround are described in detail

below.

Symptom:

This problem shows up only under the following conditions.

• SCSI write, and

• Starting address is an odd number, and

• Byte count is an odd number, and

• The combination of starting address and byte count should be such that

the transfer ends on a burst boundary, and

• D_BCNT stops decrementing (which can happen under the following

condition)

Condition #1: If D_BCNT is read after the DMA has been started.

If all of the above conditions are satisfied, the SCSI CE does not write the

last one byte to the FAS366. So the FAS366 is waiting in the DOUT phase

with a byte count of 1. So, for the problem to occur, all of the above condi-

tions have to be met, that is problem = a & b & c & d & e;

Root Cause:

Under the condition described above, the D_BCNT stops decrementing.

Since only two bytes can be written to the FAS366 at one time, the last one

byte has to be padded with another byte before it can be written to the

FAS366. For the logic which does the padding and writing to the FAS366, the

146

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

byte count must become 1 before it can initiate the padding. So byte count not

decrementing all the way to 1 makes the SCSI CE not write the last one byte

to the FAS366 (when all of the conditions described above are met).

Work Around:

The driver can look at the byte count and the starting address to calculate if

the above condition is satisfied. If the combination of the starting address and

the count show that it is a problem condition, then the driver can break the

DMA transfer into two parts. Part #1) write n–1 bytes to the FAS366. Part #2)

write 1 byte to the FAS366.

9.1.1.2 SCSI CE Gets Locked Up When Slave and DMA Collide Before Start

of the DMA Transfer to the FAS366

SCSI CE hangs when a slave access is made to the FAS366 immediately after

staring DMA, under certain conditions. Below are the two cases in which this

can happen.

• If the starting address is a multiple of 57 (adjusted for the burst size)

• If the starting address is a multiple of 63 (adjusted for the burst size)

So for a burst size of 16 bytes, the addresses will be

07h, or a modulo 16 number of 07h (this becomes a multiple of 57)

0fh, or a modulo 16 number of 0fh (this becomes a multiple of 63)

For the burst size of 32 bytes, the addresses will be

17h, or a modulo 32 number of 17h (this becomes a multiple of 57)

1fh, or a modulo 32 number of 1fh (this becomes a multiple of 63)

For the burst size of 64 bytes, the addresses will be

37h or a modulo 64 number of 37h (this becomes a multiple of 57)

3fh, or a modulo 64 number of 3fh (this becomes a multiple of 63).

The window in which the hang can happen is after the DMA in SCSI CE

has been enabled and before the first two bytes have been written to the

FAS366. For both the cases, SCSI CE will hang. For the case when the

addresses is 63, there will be a watchdog reset on the SBus.

147

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Work Around:

Device driver normally does not access the FAS366 after enabling DMA, so

it is not a problem. Device driver may access the FAS366 after enabling the

DMA, in the case of error recovery.

So, for a workaround, the driver should not access the FAS366 after

enabling DMA in SCSI CE and FAS366, until D_BCNT has started decre-

menting. After the first two bytes are written to the FAS366, it is safe for the

driver to access the FAS366. In the case of error handling, the device driver

already knows that something has gone wrong so it should reset SCSI CE first

and than access the FAS366, so the problem will not show up.

As described above (SCSI CE byte count gets frozen) reading the SCSI CE

BCNT can result in one byte getting stuck in SCSI CE. So the best way to

work-around this problem is to not access the FAS366 after the DMA has

been started, until either an interrupt or time-out has occurred. Upon an inter-

rupt or a time-out, the state of SCSI CE can be read first and then SCSI CE

can be reset. State of FAS366 can be read after resetting the SCSI CE.

9.1.1.3 D_ADDR Register is Not Initialized

D_ADDR register of the SCSI CE is not initialized after a power-on/soft re-

set.

Symptom:

If the address register has not been initialized (system was just powered on)

and if the D_BCNT was written with a value of 01, the wrong byte goes out

on the SCSI bus.

Root Cause:

If the sequence of programming SCSI CE was

• Power on

• Reset SCSI CE

• Write BCNT

• Write Addr

• Write CSR

it may cause the wrong byte to go out on the SCSI bus if this was a SCSI write

148

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

operation. After power-on, the D_ADDR register does not get self initialized.

Even software reset to SCSI CE does not initialize the D_ADDR register. At

such a time, or in a case where the previous transfer was started at an odd ad-

dress, the D_ADDR register may contain an odd number (if the previous

transfer was at an odd address, D_ADDR will contain an odd number for

sure).

When the D_ADDR register has an odd number, and D_BCNT register is

written to with a value of 1, a wrong byte could go out on the SCSI bus if this

was a SCSI write operation.

Work Around:

Make sure that the address register contains a value of 0, when D_BCNT is

being written. Suggested work around is to write 0 to D_ADDR register every

time a software reset is issued to SCSI CE, and then write D_BCNT before

writing to D_ADDR register.

9.1.2 FAS366 Core

9.1.2.1 Premature Deassertion of ATN

In message-out phase, the FAS366 deasserts the ATN signal in the middle of

the message out phase. The deassertion comes after the first byte of the mes-

sage is sent out on the SCSI bus. This problem shows up intermittently.

Work Around:

Use PIOs to the FAS366 while writing the message bytes of the message-out

phase to the FAS366.

9.1.2.2 Pre-Mature Assertion of ATN

The FAS366 asserts ATN in the middle of the data-in phase. This happens

when a set ATN command is stacked while the FAS366 is data-in phase.

Work Around:

Don’t stack set ATN command.

9.1.2.3 Mismatch Between the Number of REQs and ACKs on the SCSI Bus,

After External Bus Reset

After an external reset (SCSI bus reset) has been applied to the FAS366,

sometimes the number of REQs and ACKs in a request sense command do

not match. This causes the SCSI channel to hang.

149

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

Work Around:

After every external reset (coming from the SCSI bus to the FAS366), the de-

vice driver should issue a chip reset to the FAS366. This prevents a mismatch

between REQs and ACKs.

9.1.3 Ethernet Channel

9.1.3.1 FEPS Ethernet Channel Does Not Reset Immediately After a

Hardware Reset

The Ethernet channel does not get reset immediately when the hardware reset

is applied to the chip. The reset only takes effect many clocks after the hard-

ware reset signal is deasserted. The complication is in fast systems, when an

interrupt is asserted to the SBus, a hardware reset will not remove the inter-

rupt fast enough. The CPU, after coming back from reset, will still see the in-

terrupt bit pending when reading the Ethernet status register.

Work Around:

After a reset, the CPU has to wait for a short period of time before accessing

the FEPS Ethernet channel.

150

Sun Microelectronics

Download from Www.Somanuals.com. All Manuals Search And Download.

Fast Ethernet, Parallel Port, SCSI (FEPS) - STP2002QFP

STP2002QFP

151

Sun Microsystems,

Download from Www.Somanuals.com. All Manuals Search And Download.

STP2002QFP

A Sun Microsystems Inc. Business

2550 Garcia Avenue, Mountain View, CA, U.S.A. 94043

Fax (408) 774-8537

(408) 774-8545

may be copied or reproduced in any form or by any means or transferred to any third party without the prior written consent of Sun Microsystems

Inc.

Circuit diagrams utilizing Sun products are included as a means of illustrating typical semiconductor applications. Complete information sufficient

for design purposes is not necessarily given.

Sun Microsystems Inc. reserves the right to change products or specifications without notice.

The information contained in this document does not convey any license under copyrights, patent rights or trademarks claimed and owned by Sun

or its subsidiaries. Sun assumes no liability for Sun applications assistance, customer’s product design, or infringement of patents arising from use

of semiconductor devices in such systems’ designs. Nor does Sun warrant or represent that any patent right, copyright, or other intellectual property

right of Sun covering or relating to any combination, machine, or process in which such semiconductor devices might be or are used.

Sun Microsystems Incorporated’s products are not authorized for use in life support devices or systems. Life support devices or systems are device

or systems which are: a) intended for surgical implant into the human body and b) designed to support or sustain life; and when properly used

according to label instructions, can reasonably be expected to cause significant injury to the user in the event of failure.

Stock No: STB2002QFP-UG

Printed in USA

Download from Www.Somanuals.com. All Manuals Search And Download.

Shark Vacuum Cleaner nvc80c User Manual
Sharp Computer Monitor PN L601B User Manual
Sharp Stereo System MD MX30 User Manual
Sigma Toaster 24405 User Manual
Silex technology Network Router SX 2000WG User Manual
Sony Camcorder PMW EX1 User Manual
Sony Computer Hardware DKA MC10F User Manual
Sony Network Card A AVZ 100 11 User Manual
Stiga Lawn Mower 155 H User Manual
Sylvania TV DVD Combo SRTD309 User Manual