2-687-041-11 (1)
•Review the following chart to determine which diagram to use to
connect the equipments in your system:
Programming the
Remote Control
4
For these equipments
See reverse side
TAV-L1
A
B
C
The remote control is preset to operate Sony brand video equipment.
Sony Equipment
Cable
Programmable Code Number
101 (DVR)
Quick Setup Guide
Please follow the steps to setup your system:
Satellite receiver
201 (DSS)
or
or
D
E
F
Follow the steps below to program your system’s remote control to
operate the other video equipment.
Using the code list below, find the three-digit code number for the
manufacturer of your equipment. (If more than one code number is
listed, use the number listed first.)
1
Press and hold CABLE or SAT (FUNCTION) you
want to program and press POWER
simultaneously.
1 2 3 4
1
2
3
•See the “Cords Required” chart that appears with the diagram to
determine which cords you’ll need. You may need to purchase
extra accessories, such as cords, depending on the equipments you
plan to connect.
The selected FUNCTION button will flash.
Preparing for Use
Connecting Your System
Running Initial
Setup
Programming
the Remote Control
Enter the three-digit manufacturer’s code number
using the number buttons while the button is lit,
approximately 30 seconds.
(See reverse side)
•Turn off and unplug all equipments before making connections.
Making Video Connections
Press ENT.
Best Video
Performance
Your system includes
several types of
When the programming is correct, the selected
FUNCTION button will flash twice slowly, and
when not, flashes five times quickly.
Connector type
HDMI*
(High-Definition
Multimedia Interface)
video inputs. Use the
inputs that are
To check if the code works
If your product is not working properly
DO NOT RETURN TO THE STORE.
For service and technical assistance
Call our Customer Information Service Center (Toll Free):
1-800-222-SONY (7669) for US residents.
available on your
equipments that
provide the best
video performance,
as shown in the table
on the right.
Aim your system’s remote control at the equipment,
and press POWER. If the equipment responds, the
programming is completed. If not, try the next code
listed.
S VIDEO
Composite video
1-877-899-SONY (7669) for Canadian residents.
* Support 480i, 480p, 720p, 1080i
Tips
• If no code is input within the above specified time, or an invalid or
incorrect code number is input, the remote control automatically
goes back to the previous setting.
• In some cases, you may not be able to program your remote control
to operate other equipment. In such cases, use the equipment’s
own remote control.
Sony Corporation © 2006 Printed in Japan
• Dead batteries or removing the batteries may cause the
programmable codes to be lost and revert back to factory settings.
Reprogramming the codes may be necessary.
Preparing for Use
Connecting Your
System
Running Initial Setup
1
2
3
Manufacturer’s Codes
1
2
4
Press POWER to turn on the system.
The Initial Setup screen appears.
1 Remove the covers.
Inserting Batteries into the Remote Control
Cable Boxes
Insert two size AA batteries (supplied) by matching the and on
the batteries to the diagram inside the remote control’s battery
compartment.
Manufacturer
Sony
Code
Press MONITOR to switch the remote
FUNCTION to MONITOR.
101
Hamlin/Regal
Jerrold/G.I./Motorola
123, 123, 125, 126, 127
Press / to select the monitor language displayed
5
102, 103, 104, 105, 106, 107, 108, 109, 117,
118, 119, 123, 133
on the menu screens, then press (OK).
Oak
128, 129, 130
111, 113, 120, 121, 122, 131
113, 116
Press DVD (FUNCTION) to switch the remote
FUNCTION to DVD.
3
6
7
Panasonic
Pioneer
2 See reverse side to connect this system and other equipment.
Press DVD (direct input select) to switch the input
to DVD.
3 Connecting the FM wire antenna.
RCA
132
Attaching the frame grille
Scientific Atlanta
Tocom/Philips
Zenith
110, 111, 112
117, 118
Press (ENTER) without inserting a disc.
The Setup Display for selecting the DVD language
used in the on-screen display appears.
113, 114
Satellite Receivers
LANGUAGE SETUP
OSD:
ENGLISH
MENU:
AUDIO:
SUBTITLE:
Manufacturer
Sony
Code
201
ENGLISH
FRENCH
VIDEO
DIGITAL DIGITAL
IN OUT
DVD
SPANISH
FM
ANTENNA
PORTUGUESE
OPT
FM wire antenna
Hitachi
205
75
COAXIAL
COAX
General Electric
Hughes
202
204
JVC/Dish Network/Echostar
Mitsubishi
Panasonic
210
4 Bundle the connected cords, then replace the covers.
Press / to select the language, then press
(ENTER).
The system displays the on-screen display, the
menu and subtitles in the selected language.
209
203
Philips
211
RCA/PROSCAN
Samsung
202, 208
212
Toshiba
206, 207
Note
Depending on the connected equipment cords, the back covers may not attach properly. In
this case, try other cords, or use the system without the back covers.
Download from Www.Somanuals.com. All Manuals Search And Download.
|