3-866-334-11(1)
Se t t in g t h e Co m p o n e n t Co d e s
Op e ra t in g a Co m p o n e n t
Re m o t e Bu t t o n De scrip t io n s
To use this Remote Commander with a Sony brand component that
is already preset at the factory (see the table on the left), you can skip
this procedure.
If you are using other brand’s component or if you cannot operate
even a Sony brand component, follow this procedure.
1
Set the slide sw itch to the position of your component.
Se t t in g b y Se a rch in g fo r t h e Co rre ct Co d e
If you’ve tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component
was not listed), try the following.
RM-V201T
Remote Commander
Op e ra t in g a TV/Sa t e llit e Tu n e r
TV
Operating Instructions
Mode d’emploi (au verso)
1
0
!¡
1 To switch to Teletext.
2 To change the input mode.
3 Fastext buttons.
4 To change the programme.
Also to turn on the power.
5 To select double-digit numbers.
Works in the same way as your
TV’s commander.
6 To move the cursor upward,
downward, to the right or left.
7 To call up the MENU display.
8 Volume up: +
1
2
Turn on the component you wish to set up using its power
switch.
Set the slide switch on the Remote Commander to the desired
2
3
2
Point the Commander directly to your component and press
the button for the desired function.
See “Remote Button Descriptions” for details.
Sony Corporation © 1999 Printed in Malaysia
Se t t in g b y En t e rin g t h e Co d e Nu m b e r
See the supplied “Component Code Numbers” and find the code for
your component.
position.
3
4
Press the S (Set) button.
4
No t e s o n u sin g t h e Co m m a n d e r
Aim the Commander to your component, and press and release
the PROGR+ button. Then press and release the u button.
Repeat step 4 until the correct code number is found.
Each time you press the PROGR+ button and then the u button, a
new code number will be transmitted.
• Using this Commander will not add new functions to your components. The
functions of the Commander are limited to the functions of the component
itself. For example, if your TV does not have a mute function, the ¤ button
on this Commander will not function with your TV.
1
Set the slide sw itch to the position that corresponds to the
component to set up.
English
5
5
!™
6
7
• Do not forcibly remove or tear off the corner protector.
!£
!¢
Keep trying until your component operates as follows:
• TV, VCR or satellite tuner : the power turns off.
• TV without a power switch: the Channel + function works.
Ab o u t t h is Re m o t e Co m m a n d e r
In st a llin g t h e Ba t t e rie s
Volume down: –
8
9
9 To mute volume on TV.
0 To turn off the power.
!¡ To turn on.
To return from Teletext to TV.
!™ To select a number between 20
and 29.
You can set up this Remote Commander to operate the following
components of almost all major brands including Sony.
Open the battery compartment and insert two R6 (size AA) batteries
(not supplied).
To se t u p ...
a TV
Se t t h e slid e sw it ch t o ...
Tro u b le sh o o t in g
If you’re having problems setting up or using the Remote
Commander:
Be patient as you do this; it may take up to about 100 tries for a
TV, and 70 to 80 tries for other components until the correct code
number is located.
!∞
Be sure to line up the + and – on the batteries with the + and – on the
battery compartment.
TV
Po sit io n
TV
Fa ct o ry se t t in g
Co m p o n e n t t h a t ca n b e p re se t
a satellite tuner
a VCR
SAT
Sony TV
TV
6
7
When the correct code is found, press the … button.
Turn on the component again, and check that the Commander
can control the other functions of your component such as
channel and volume control.
VCR or AUX
• When setting up the Commander, carefully go through the
procedures described under “Setting the Component Codes”. If the
code that’s listed first for your component doesn’t work, try all the
codes for your component — in the order in which they’re listed. If
all the codes fail to work (or if your component is not listed), try
using the procedures under “Setting by Searching for the Correct
Code”.
• Check that you’re aiming the Commander directly at the
component, and that there are no obstructions between the
Commander and the component.
VCR
Sony VHS VCR (VTR3) VCR
Sony DV (VTR4)
1
2
!£ To enter the selection.
!¢ Programme up: +
Programme down: –
!∞ To operate JUMP,
AUX
SAT
2
3
Press the S (set) button.
TV, VCR, or satellite tuner
Sony satellite tuner
If the component does not operate properly, repeat steps 3 to 6 and
search for another code.
FLASHBACK, or CHANNEL
on the TV, depending on the
manufacturer’s setting.
Enter the three-digit component code in the “Component
Code Numbers” table.
If you still cannot get the Commander to work properly, see
“Troubleshooting”.
Sp e cifica t io n s
Operable distance
For example, to set a Philips’ TV, press
.
Sa t e llit e Tu n e r
No t e
Be sure to proceed to each next step in the above procedure within 10 seconds;
otherwise setting mode will be canceled.
Wh e n t o re p la ce t h e b a t t e rie s
• Make sure the batteries you’re using are not worn out, and that
they’re inserted correctly.
Approx. 10 m (33 ft) (varies depending on the component of
each manufacturer)
2 To change the input mode
!™ To select a number between 20
and 29.
Under normal conditions, batteries will last up to six months. If the
Remote Commander does not operate properly, the batteries might
be worn out. Replace the batteries with new ones.
(H/ V).
• Check that the slide switch of the Remote Commander is set to the
position (TV, VCR, SAT or AUX) for your desired component.
• If you cannot preset a component to the AUX or SAT position of
the slide switch, a component type different from that of the
component you intend to preset may be assigned to that position.
In such a case, follow the procedure in “Setting Another TV, VCR,
or Satellite Tuner” first.
• Check that the component has infrared remote capability. For
example, if your component didn’t come with a remote control, it
probably isn’t capable of being controlled by the Remote
Commander.
Pow er requirements
Two R6 (size AA) batteries (not supplied)
Battery life
4 To change the programme.
!£ To enter the selection.
Se t t in g An o t h e r TV, VCR, o r Sa t e llit e Tu n e r
When you have two or more components of the same type (for
example, three VCRs), you can set the code number of the
component’s type on any empty position of the slide switch of the
Remote Commander (AUX or SAT position only).
5 To select double-digit numbers. !¢ Programme up: +
Work in the same way as your
satellite tuner’s commander.
Programme down: –
!∞ To operate JUMP,
No t e s
4
5
Press the … button.
Approx. six months (varies depending on frequency of use)
Dimensions
• Replace both batteries with new ones.
• Do not take more than 20 minutes to replace the batteries; otherwise, your
setting of the code numbers will be erased.
6 To move the cursor upward,
downward, to the right or left.
7 To call up the MENU display.
8 To control the volume on TV.
9 To mute the volume on TV.
0 To turn on and off the power.
FLASHBACK or CHANNEL
RETURN function on the
satellite tuner, depending on
the manufacturer’s setting.
Approx. 63 × 200 × 38 mm (w/ h/ d) (2 1/
Mass
2
× 7 7/
8
× 1 1/
in.)
2
1
2
3
4
Set the slide switch on the Remote Commander to AUX or SAT.
Press the S (Set) button.
Press the p button.
Press one of the following buttons;
1 to set up a VCR
Aim this Commander to your component and check if you can
operate it using this Commander.
Approx. 120 g (4.2 oz.) (not including batteries)
No t e s o n Ba t t e rie s
• Do not mix old batteries with new ones or mix different types of
batteries together.
Design and specifications are subject to change without notice.
Go through the same procedure for each component you want to set
up.
• If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.
• Should any problem persist, reset the Commander to the factory
setting by pressing the u, … and Á– buttons simultaneously.
8 to set up a TV
9 to set up a satellite tuner
If yo u ca n n o t o p e ra t e yo u r co m p o n e n t ...
• First, try repeating these set up procedures using the other codes
listed for your component (see “Component Code Numbers”).
• If — after trying all the codes listed for your component — you still
cannot get the Commander to work properly, try the search
method described under “Setting by Searching for the Correct
Code”.
Op e ra t in g a VCR
If you have any questions or problems concerning the Remote
Commander that are not covered in this manual, please call the
telephone number in the warranty.
5
6
Press the … button.
Enter the component’s code number by following steps 2 to 5 of
“Setting by Entering the Code Number”, or steps 3 to 7 of
“Setting by Searching for the Correct Code”.
1 To switch the signals supplied to
the TV.
2 To change the programme.
3 To select double-digit numbers.
Works in the same way as your
VCR’s commander.
9
1
No t e s
4 To play
5 To rewind
2
3
4
• Be sure to proceed to each next step in the above procedure within 10
seconds; otherwise, the setting mode will be canceled.
• You cannot set up more than one component at a time on each position of the
slide switch. If you want to set up two or more same components of different
brands, see “Setting Another TV, VCR, or Satellite Tuner”.
6 To record, press ( while
pressing r.
7 To control the volume on TV.
8 To mute the volume on TV.
9 To turn on and off the power.
0 To select a number between 20
and 29.
!¡ To fast-forward
!™ To stop
!£ To pause
!¢ Programme up: +
Programme down: –
0
!¡
!™
!£
!¢
5
6
Tip
You can write down the code number on the label inside the battery
compartment lid.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|