DME PROCESSOR PACK
MVE-8000A-C
MULTI FORMAT DME PROCESSOR
MVE-8000A
HK-PSU02
MKE-8020A
MKE-8040A
INSTALLATION MANUAL
1st Edition
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
Rear:
10 cm (4 inches) or more
Right, Left: 4 cm (1.6 inches) or more
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
: DATA connector
: CTRL connector
Follow the instructions for the above port(s).
MVE-8000A
1 (P)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 2
Related manuals......................................................................................................... 2
Contents ..................................................................................................................... 2
Trademark.................................................................................................................. 2
1. Installation
1-1. Operating Environment ............................................................................... 1-1
1-2. Power Supply .............................................................................................. 1-1
1-2-1. Power Specifications .................................................................. 1-1
1-2-2. Recommended Power Cord........................................................ 1-2
1-3. Installation Space (External dimensions) .................................................... 1-3
1-4. Installing the Options .................................................................................. 1-4
1-4-1. Installing the Plug-in Boards...................................................... 1-4
1-4-2. Installing the Connector Board .................................................. 1-6
1-4-3. Installing the HK-PSU02 ........................................................... 1-7
1-5. Rack Mounting ............................................................................................ 1-9
1-6. Matching Connectors and Cables..............................................................1-11
1-7. Input/Output Signals of Connectors .......................................................... 1-12
1-8. Checks on Completion of Installation .......................................................1-13
1-8-1. On-board Switches Setting and LED Functions ...................... 1-13
1-9. System Connection.................................................................................... 1-22
2. Service Overview
2-1. Troubleshooting .......................................................................................... 2-1
2-2. Periodic Inspection and Maintenance ......................................................... 2-2
2-2-1. Cleaning ..................................................................................... 2-2
2-3. About the Data Backup Capacitor............................................................... 2-2
MVE-8000A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Structure
Purpose of this manual
This manual is the installation manual of DME Processor Pack MVE-8000A-C and
their optional boards and units.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the MVE-8000A-C system.
Related manuals
The following manuals are prepared for MVE-8000A-C and their optional boards
and units.
. Operation Manual (Supplied with MVE-8000A-C)
This manual describes the application and operation of MVE-8000A-C system.
. Maintenance Manual (Available on request)
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space,
installation of optional boards and units, rack mounting, connectors, input and
output signals of connectors, checking upon completion of installation, and system
configuration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
Trademark
Registered trademark used in this manual is follows.
. Ethernet is a registered trademark of Xerox Corporation.
MVE-8000A
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
Installation
1-1. Operating Environment
1-2. Power Supply
Operating guaranteed temperature : +5 dC to +40 dC
1-2-1. Power Specifications
Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity :
(relative humidity)
Storage temperature :
10 % to 90 %
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
_20 dC to +60 dC
Mass (when all options are installed) : Approx. 16.5 kg
Power requirements :
Power frequency :
Current consumption (when all options are installed) :
2.8 to 1.2 A
AC 100 to 240 V
50/60 Hz
Prohibited locations for installation
. Areas where the unit will be exposed do direct sunlight
or any other strong lights.
. Dusty areas
. Areas subject to vibration.
m
. Areas with strong electric or magnetic fields.
. Areas near heat sources.
. Areas subject to electrical noise.
. Areas subject where is subjected to static electricity.
. As the inrush current at turn-on is a maximum 14 A (at
100 V)/66 A (at 240 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will
abnormally operate.
Ventilation
The inside of the MVE-8000A-C is cooled by a fan (both
sides).
The power supply can be damaged if the exhaust vent
(both sides) and air intake (front panel) are blocked or the
fan is stopped.
. The MVE-8000A contains the single power supply unit
as the standard configuration. A maximum of two power
supply units may be installed. When starting up the
MVE-8000A, be sure to turn on the power of one or
more power supply units.
Therefore, leave a blank space of more than 10 cm in the
front and both sides of the MVE-8000A-C.
MVE-8000A
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2-2. Recommended Power Cord
This unit does not come with a power cord.
To get a power cord, please contact your local Sony Sales
Office/Service Center.
w
. Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Volt-
age, Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please contact your local Sony
Sales Office/Service Center.
w
. Never use an injured power cord.
. Plugging the power cord in the AC inlet, push as far as it
will go.
For customers in the U.S.A. and Canada
1 Power cord, 125 V 10 A (2.4 m) : ! 1-557-377-11
AC inlet
1
For customers in the all European countries
1 Power cord, 250 V 10 A (2.4 m) : ! 1-782-929-12
AC inlet
1
MVE-8000A
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3. Installation Space (External dimensions)
440
MVE-8000A
MULTI FORMAT DME PROCESSOR
375
482
Unit : mm
MVE-8000A
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4. Installing the Options
1-4-1. Installing the Plug-in Boards
The MVE-8000A-C is shipped from the factory with the
necessary option (refer to the following table) already
installed in the MVE-8000A, in accordance with the
specified system configuration.
c
Be sure to turn off the POWER switch and unplug the
power cord from the wall outlet before starting the installa-
tion work.
If the installation work is started with the POWER switch
left on, it may cause electrical shock or damage of printed
circuit boards.
MVE-8000A-C options
Model name
Board configuration
Plug-in board Connector board
Installation procedure
1. Turn off the main power of the MVE-8000A and
disconnect the AC power cord from the wall outlet.
2. Loosen the four screws (with drop-safe) and remove
the front door assembly in the direction of the arrow.
MKE-8020A
MVS Interface Board
_
CN-2153 board
MKE-8040A
Advanced Effects Board
DVP-30A board
HK-PSU02
_
_
Power Supply Unit
Screws
(with drop-safe)
Front door assembly
Screws
(with drop-safe)
3. Remove the four screws (B3 x 5), and remove the
“plug-in board loose-proof assembly”.
B3 x 5
Plug-in board
loose-proof assembly
B3 x 5
MVE-8000A
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. While the eject levers are kept open as shown in the
illustration, insert the plug-in board into the board
guide rails.
5. While closing the eject levers in the direction of arrow,
push in the plug-in board.
Eject lever
Plug-in board
Plug-in board
Eject lever
Eject levers
Name of option
Name of board
Slot on the front side
MKE-8040A
DVP-30A board*1 2, 3
*1 : The DVP-30A boards are assigned to the following channels in
Plug-in board
accordance with the slots to which the boards are inserted.
Slot
Channel
2
3
CH1, CH2
CH3, CH4
6. Attach the plug-in board loose-proof assembly and the
front door assembly by reversing the installation steps
2, 3.
MVE-8000A
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4-2. Installing the Connector Board
The board slot
Connecting the connecting cable
3. Remove the two screws of the slot 2 cover panel.
Name of option
Name of board
Slot on the rear side
MKE-8020A
CN-2153 board
1
Cover panel
(Slot 2)
Installation procedure
Parts required (Supplied accessory of MKE-8020A)
. Connecting cable
. Cable holder bracket
1. Remove the two screws and remove the cover panel.
n
Store the removed cover panel in a safe location.
B3 x 5
4. Connect the connecting cables to the connectors.
Slot 1
Connectors
B3 x 5
Cover panel
2. Insert the connector board horizontally level and
secure it with the two fixing screws.
Connecting cables
Fixing screw
Slot 1
Connector board
Fixing screw
MVE-8000A
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4-3. Installing the HK-PSU02
5. Secure the cable holder bracket and the slot 2 cover
panel with the screws removed in step 3 as shown in
the figure.
The HK-PSU02 is used after it is installed in the MVE-
8000A.
c
Connecting cable
Before installing the HK-PSU02, be sure to turn off the
main power. If the HK-PSU02 is installed while the main
power is turned on, it can result in electrical shock or
damage to printed circuit boards.
Installation procedure
1. Remove the front door assembly of the MVE-8000A.
(Refer to Section 1-4-1.)
2. Remove the two screws (PSW3 x 6) fixing the power
dummy panel, and remove the power dummy panel.
n
Cable holder
bracket
Connecting cable
Cable holder
Cover panel
bracket
(Slot 2)
Store the removed power dummy panel in a safe place.
Connecting cable
B3 x 5
Power dummy panel
PSW3 x 6
MVE-8000A
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Push the portion of the HK-PSU02 indicated by the
arrow and insert the HK-PSU02 into deep end as far as
it will go.
4. Secure the HK-PSU02 with the two screws removed in
step 2.
HK-PSU02
PSW3 x 6
5. Install the front door assembly by reversing the
installation steps 1 to 4.
MVE-8000A
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Rack mounting procedure
1-5. Rack Mounting
This section describes the rack mounting procedure using
the RMM-10 rack mount kit.
The MVE-8000A installs in a 19-inch standard rack.
To mount the MVE-8000A in a rack, use the specified rack
mount kit and follow the procedure described below.
n
Tighten the screws to the following torque.
Tightening torque : 120 x 10_2 N.m {12.2 kgf.cm}
Specified rack mount kit : RMM-10
n
1. Remove the four screws to detach the four feet
assembly from the bottom of the equipment.
If a rack mount kit other than the specified one is used, the
unit may not be correctly install in a 19-inch standard rack.
Parts of the RMM-10
. Rack tools
2 pcs
1 pc
1 pc
. Right rack mount adaptor
. Left rack mount adaptor
. Rack tool attaching screws
(B4 x 6 : 7-682-560-09)
. Rack tool attaching screws
(B4 x 10 : 7-682-560-10)
6 pcs
6 pcs
1. Precautions for rack mounting
w
Feet
assembly
B4 x 6
Feet
assembly
. To prevent the rack from falling or moving, fix the rack
on a flat and steady floor using bolts or other fixings.
If the rack falls due to the weight of the equipment, it
may cause death or injury.
B4 x 6
2. Attach the rack tool to the side of the equipment using
the specified six screws.
n
Use B4 x 6 screws.
. Be sure to use the specified rack mount kit.
If not, injury may result and the equipment may fall due
to insufficient strength.
. After rack mounting, be sure to tighten the screws on the
rack angle and fix the unit in the rack.
Rack tool
B4 x 6
If the screws on the rack angle are not tightened, the unit
may slip from the rack and fall, causing injury.
c
When mounting the unit in the rack, note the following:
. Be sure to mount in the rack with two persons or more.
. Be careful not to catch your fingers or hands in the rack
mount rail or others.
. Mount in the rack in a stable position.
n
If several units are mounted in a rack, it is recommended
that a ventilation fan is installed to prevent temperature rise
inside the rack.
Rack tool
B4 x 6
MVE-8000A
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loosen the screws on the rear of the right and left
adaptors and adjust the length of the adaptor according
to the depth of the rack.
5. Tighten the screws (B4 x 6 : two screws each on the
right and left) for adjusting the length of the adaptor
completely (the screws that were loosened in step 2).
6. Align the groove of the rack tool at the side of the
equipment with the rail, and slide the equipment to the
rear.
(The illustration below shows the left adaptor.)
n
The rack tools are hooked on the rails as shown below.
Adaptor
Portion of
the rail
B4 x 6
B4 x 6
Rack tool
Rail
Rack tool
Rail
n
Maximum depth of adaptor :750 mm
Minimum depth of adaptor : 595 mm
7. Remove the front door assembly.
(Refer to Section 1-4-1.)
8. Fix the rack angles in the rack using the specified
screws.
4. Attach the right and left adaptors to the rack complete-
ly using the specified six screws.
(The illustration below shows the left adaptor.)
31.75
B4 x 10
2U
B5 x 12
B4 x 10
31.75
Unit : mm
B5 x 12
9. Install the front door assembly to the equipment.
MVE-8000A
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
1-6. Matching Connectors and Cables
Use the following connectors, cables or equivalents when connecting cables to the unit.
Model name
Panel indication
Connector name
Matching connector and cable
Name
Sony part No.
MVE-8000A
REF IN
BNC, 75 Z
BNC, 75 Z
BELDEN 8281 coaxial cable
REMOTE 1-4
D-sub 9-pin, Female
D-sub 9-pin, Male
Connector 9-pin, Male
Junction Shell 9-pin
1-560-651-00*1
1-561-749-00
GPI
GPI2
D-sub 25-pin, Female
D-sub 25-pin, Male
Connector 25-pin, Male
Junction Shell 25-pin
1-560-904-11*1
1-563-377-11
DATA
CTRL
RJ-45 modular jack*2
MDR 68-pin, Female
_
_
MKE-8020A
SWITCHER A, B
Dedicated cable
_
(Supplied accessory of MKE-8020A)
*1 : The following crimp contact is required for the plug.
AWG#18 to #22 : 1-566-493-21
AWG#22 to #24 : 1-564-774-11
AWG#24 to #30 : 1-564-775-11
*2 : Conforms to the IEEE 802.3 Ethernet100BASE-TX standards.
MVE-8000A
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
GPI, GPI2 : (D-sub 25-pin, Female)
INPUT x 8, TTL
1-7. Input/Output Signals of Connectors
OUTPUT x 4, relay contacts 30 V 0.1 A
(resistive load)
OUTPUT x 4, open collector 30 V rated voltage
The input/output signals of the connectors at the rear panel
are as follows.
n
13
25
1
<CONTROLLER> indicates a controlling device.
<DEVICE> indicates a controlled device.
14
_ EXT VIEW _
REMOTE 1-4 : RS-422A (D-sub 9-pin, Female)
<DEVICE> (*1)
Pin No.
Signal Name
Function
1
GND
Ground
Ground
1
5
2
GND
9
6
3
GPI IN 2
General-purpose input
_ EXT VIEW _
4
GPI IN 4
5
GPI IN 6
Pin No.
Signal Name
Function
6
GPI IN 8
1
2
3
4
5
6
7
8
9
FG
Frame ground
Transmitted data (_)
Received data (+)
Ground
7
GPI OUT 1B
GPI OUT 2B
GPI OUT 3B
GPI OUT 4B
GPI OUT 6
GPI OUT 8
General-purpose relay output (B)*2
TX_
RX+
GND
_
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
No Connection
Ground
General-purpose open collector
output*3
GND
TX+
RX_
_
Transmitted data (+)
Received data (_)
No Connection
GPI OUT COM Ground for open collector output
GND
Ground
GPI IN 1
General-purpose input
GPI IN 3
(*1) : Editing control unit such as BVE-9100 (EDITOR)
GPI IN 5
GPI IN 7
DATA
CTRL : 100BASE-TX, RJ-45 (8-pin)
GPI OUT 1A
GPI OUT 2A
GPI OUT 3A
GPI OUT 4A
GPI OUT 5
GPI OUT 7
General-purpose relay output (A)*2
8
1
General-purpose open collector
output*3
_ EXT VIEW _
Pin No.
Signal Name
Function
GPI OUT COM Ground for open collector output
1
2
3
4
5
6
7
8
TX+
TX_
RX+
_
Transmitted data (+)
Transmitted data (_)
Received data (+)
No Connection
n
A and B of the same number constitute a pair of relay contacts.
(*2)<Relay>
GPI OUT n B
_
No Connection
GPI OUT n A
RX_
_
Received data (_)
No Connection
+V
n;1-4
_
No Connection
(*3)<Open collector output>
GPI OUT 5-8
GPI OUT COM
MVE-8000A
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
D5 (A-2) : +12 V
+12 V power supply status indication.
Lit when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
1-8. Checks on Completion of Installation
1-8-1. On-board Switches Setting and LED Functions
n
The number shown in parentheses ( ) indicates the address on the circuit board.
1. CA-54CFC board (MVE-8000A)
A
B
C
D
E
S403
TP1301
1
2
3
4
5
1
2
3
4
5
F
S402
S401
E
D
C
B
A
SW1
D4
D409
D5
D410
SW2
DI4
DI1
D1303
D601
D602
D704
D701
D1002
D1001
D1201
D1202
CPU-DK
Module
D12
D18
D19
D14
D15
D16
D17
(COM CPU-1)
S102
S103
CPU-DR
Module
(MAIN CPU)
1
2
3
4
5
F
SW2
SW1
D10
D13
E
D
C
B
A
SW1
S101
SW2
DI4
DI1
ND101
ND102
ND901
ND902
ND1101
ND1102
S902
S1102
CPU-DK
Module
A
1
B
C
D
E
(COM CPU-2)
S104
S901
D3
D6
1
2
2
DIF-130
(PC CARD)
D7
D101
D102
D103
D104
D901
D902
D903
D904
D1101
D1102
D1103
D1104
D1
D4
D2
S1101
A
D5
3
D100
D101
D200
B
SG-272
A side/Component side
D409 (A-2) : RESET status LED
System reset status indication.
<LED>
D4 (A-1) : +3.3 V
Lit when S401 is pressed or the power voltage drops to
+3.3 V power supply status indication.
+3.3 V.
Lit when the +3.3 V power is supplied.
D410 (A-2) : CPU RESET status LED
CA-54CFC board reset status indication.
Lit when S402 is pressed or the power voltage drops to
+3.3 V.
D601 (A-2) : REF EXT status LED
REF IN signal presence/absence status indication.
Lit when the REF signal is input to the REF IN connector.
Not lit when the REF signal is not input to the REF IN
connector.
D101, D102, D103, D104 (A-4), ND101 (A-3), ND102
(A-4) : MAIN CPU status LED
Main CPU status indication.
MVE-8000A
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
D1303 (A-2) : +5 V
+5 V power supply status indication.
Lit when the +5 V power is supplied.
D602 (A-2) : PLL LOCK status LED
REF IN signal format status indication.
Lit when the REF IN signal matches with the switcher
format setup.
<Switch>
S101 (A-3) : Mode setting switch for the main CPU
Sets the modes of the main CPU, but this switch is current-
ly not in use. Factory setting is all OFF.
D701 (A-2) : SBUS RX status LED
S-BUS reception status indication.
Lit while the data reception is in progress.
S102 (A-2) : Group ID setting switch for LAN
Sets the group ID for connecting LAN.
Factory setting and in standard use :
Bit 1 : ON
D704 (A-2) : SBUS TX status LED
S-BUS transmission status indication.
Lit while the data transmission is in progress.
Bits 2 to 8 : OFF
S103 (A-2) : Unit ID setting switch for LAN
Sets the unit ID for connecting LAN. Do not change the
D901 (A-4), D902, D903, D904 (A-5) : COM CPU-1
status LED
COM CPU-1 status indication.
setting.
Factory setting :
Bit 1 : ON
Bits 2 to 8 : OFF
D1001 (A-2) : COM1 100 status LED
COM CPU-1 Ethernet communication speed status
indication.
S104 (A-4) : Monitor reset switch for the main
CPU
Lit :
Not lit : 10 Mb/s
100 Mb/s
Used for maintenance purpose. Pressing this switch resets
the system while maintaining this unit through the main
CPU control terminal pin (CN103).
D1002 (A-2) : COM1 ACT status LED
COM CPU-1 Ethernet communication status indication.
Lit while data transmission or reception is in progress.
S401 (A-1) : System reset switch
Pressing this switch activates the system-reset and the
system restarts.
D1101, D1102, D1103, D1104 (A-5) : COM CPU-2
status LED
S402 (A-1) : CA-CPU reset switch
COM CPU-2 status indication.
Pressing this switch resets the CA-54CFC board.
D1201 (A-2) : COM2 ACT status LED
COM CPU-2 Ethernet communication status indication.
Lit while data send or receive is in progress.
S403 (B-1): Switch setting the number of the
power supply units
Sets the number of the power supply units that are required
for this unit. Do not change the setting.
Factory setting:
D1202 (A-2) : COM2 100 status LED
COM CPU-2 Ethernet communication speed status
indication.
Bits 1 and 2: ON
Bits 3 and 4: OFF
Lit :
100 Mb/s
Not lit : 10 Mb/s
S901 (A-4) : Monitor reset switch for the COM CPU-1
Used for maintenance purpose. Pressing this switch resets
the system while maintaining this unit through the COM
CPU-1 control terminal pin (CN503).
S902 (A-4) : Modes setting switch for the COM CPU-1
Sets the modes of the COM CPU-1, but this switch is
currently not in use. Factory setting is all OFF.
ND901, ND902 (A-4) : COM CPU-1 status LED
COM CPU-1 status indication.
ND1101, ND1102 (A-4) : COM CPU-2 status LED
COM CPU-2 status indication.
MVE-8000A
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
D18 (A-4) : +3.3 V
Indicates the status of the VCC (I/O) power that is supplied
to the CPU-DR module.
S1101 (A-4) : Monitor reset switch for the COM CPU-2
Used for maintenance purpose. Pressing this switch resets
the system while maintaining this unit through the COM
CPU-2 control terminal pin (CN703).
<LED on the CPU-DK module> : COM CPU-1
: COM CPU-2
DI1 (B-5) : CD (Card Detect) status LED
Lit when the CPU-DK module is inserted correctly to the
parent board.
S1102 (A-4) : Modes setting switch for the COM
CPU-2
DI2 (F-3) : RUN status LED
Sets the modes of the COM CPU-2, but this switch is
currently not in use. Factory setting is all OFF.
Lit when the CPU-DK module starts operating.
DI3 (F-3), DI6 (F-3), DI7 (F-3), DI8 (F-4) : STATUS1
to STATUS4 LED
Used for maintenance purpose. Only the STATUS1 LED is
lit in normal operation.
<LED on the CPU-DR module> : Main CPU
D10 (A-1) : RUN status LED
RUN status indication.
Lit when the CPU-DR module starts operating.
DI4 (B-5) : +3.3 V
D12 (A-4) : CD (Card Detect) status LED
Lit when the CPU-DR module is inserted correctly into the
parent board.
Indicates the status of the VCC (CORE) and VCC (I/O)
powers that are supplied to the CPU-DK module.
Lit while the specified power is turned on.
D13 (A-1) : +2.5 V
Indicates the status of the +2.5 V power that is generated
by the VCC (CORE) and supplied to the CPU-DR module.
Lit while the specified power is turned on.
D14, D15, D16, D17 (A-3) : STATUS1 to STATUS4
status LED
Used for maintenance purpose. Only the STATUS1 LED is
lit in normal operation.
Lit while the specified power is turned on.
D19 (A-4) : CORE status LED
Indicates the status of the VCC (CORE) power that is
supplied to the CPU-DR module.
Lit while the specified power is turned on.
<Switch on the CPU-DR module> : Main CPU
SW1 (A-1) : RESET switch
Pressing this switch resets the CPU-DR module.
n
In some machines in which the CPU-DR module is
installed, the system reset may be activated.
SW2 (A-2) : MODE switch
Used only for production in the assembly factory. All
switches are set to OFF for normal operation.
Factory setting is all OFF.
MVE-8000A
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
<Switch on the CPU-DK module> : COM CPU-1
: COM CPU-2
SW1 (D-5) : RESET switch
Pressing this switch resets the CPU-DK module.
n
In some machines in which the CPU-DK module is
installed, the system reset may be activated.
SW2 (C-5) : MODE switch
Used only for production in the assembly factory. All
switches are set to OFF for normal operation.
Factory setting is all OFF.
<LED on the DIF-130 board> : PC card
D1 (A-1) : DETECT A
Lit when a compact flash is inserted correctly into socket
A.
D2 (A-1) : DETECT B
Lit when a compact flash is inserted correctly into socket
B.
D3 (A-1) : +3.3 V
+3.3 V power supply status indication.
Lit when +3.3 V power is supplied.
D4 (A-1) : ACTIVE A
Lit or flashes during communication with the compact
flash in socket A.
D5 (A-1) : ACTIVE B
Lit or flashes during communication with the compact
flash in socket B.
D6 (A-1) : CD (Card Detect) status LED
Lit when the DIF-130 board is inserted into the parent
board correctly.
D7 (A-1) : GPO status LED
This switch is currently not in use.
<LED on the SG-272 board>
D100 (B-1) : REF OK status LED
Lit while V sync of the reference input is detected.
D101 (B-1) : REF EXT status LED
Lit while sync signal is input to the reference input.
D200 (B-1) : LOCK status LED
Lit while the machine is locked to the reference signal.
MVE-8000A
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
D502 (A-2) :
+2.5 V-1
Lit when CPU A accesses the FPGA.
D503 (A-3) : +1.5 V-1
D504 (A-2) :
+12 V
D1001 (A-7) : BOOT DONE status LED
2. DVP-30A board (MKE-8040A)
A
B
C
D
E
F
G
H
J
K
1
2
D504
D501
D502
D12
D505
D503
D506
ND1201
ND1202
D18
D19
D14
D15
D16
D17
SW2
CPU-DR
Module
(CPU B)
3
4
SW1
S901
S1201
D10
D13
D1204
D1203
D1202
D1201
5
D703
D702
D701
ND1101
6
7
ND1102
D12
S801
D18
D19
D14
D15
D16
D17
SW2
S1101
D1104
D1103
D1102
D1101
D1004
D1002
D1003
D1001
CPU-DR
Module
(CPU A)
SW1
D10
D13
8
A side/Component side
<LED>
D506 (A-3) :
+1.5 V-2
D501 (A-2) :
+3.3 V
+1.5 V-2 power supply status indication.
+3.3 V power supply status indication.
Lit when +1.5 V-2 power is supplied.
Lit when +3.3 V power is supplied.
D701 (A-5) : BUS A status LED
+2.5 V-1 power supply status indication.
Lit when +2.5 V-1 power is supplied.
D702 (A-5) : BUS B status LED
Lit when CPU B accesses the FPGA.
+1.5 V-1 power supply status indication.
D703 (A-5) : READ status LED
Lit when +1.5 V-1 power is supplied.
Lit when CPU A or B makes the read access to the FPGA.
+12 V power supply status indication.
Lit when IC108 starts up.
Lit when +12 V power is supplied.
D1002 (A-7) : DLKD status LED
Lit when the DLL (Delay Locked Loop) of the FPGA is
locked. If the LED does not light, the FPGA may be
defective.
D505 (A-2) : +2.5 V-2
+2.5 V-2 power supply status indication.
Lit when +2.5 V-2 power is supplied.
D1003 (A-7) : RCB DONE status LED
Lit when the FPGA configuration is complete.
MVE-8000A
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
D1004 (A-7) : SYSTEM status LED
Lit when configuration is complete and FPGA reset is also
complete. If the LED does not light, the FPGA may be
defective.
<LED on the CPU-DR module> (C-3) and (C-7)
Refer to <LED on the CPU-DR module> in “1. CA-54
CFC Board”.
<Switch on the CPU-DR module> (C-3) and (C-7)
Refer to <Switch on the CPU-DR module> in “1. CA-54
CFC Board”.
D1101 (A-7) : DGB 7 A status LED
Used for design purpose.
D1102 (A-7) : DGB 6 A status LED
Used for design purpose.
D1103 (A-7) : DGB 5 A status LED
Used for design purpose.
D1104 (A-7) : DGB 4 A status LED
Used for design purpose.
D1201 (A-4) : DGB 7 B status LED
Used for design purpose.
D1202 (A-4) : DGB 6 B status LED
Used for design purpose.
D1203 (A-4) : DGB 5 B status LED
Used for design purpose.
D1204 (A-4) : DGB 4 B status LED
Used for design purpose.
ND1101 (A-6), ND1102 (A-6) : STATUS A LED
The status indication of the CPU A on the DVP-30A
board.
ND1201 (A-3), ND1202 (A-3) : STATUS B LED
The status indication of the CPU B on the DVP-30A board.
<Switch>
S801 (A-6) : CPU A CONFIG switch
Used for maintenance purpose.
S901 (A-4) : CPU B CONFIG switch
Used for maintenance purpose.
S1101 (A-7) : SETUP A switch
Used for maintenance purpose.
S1201 (A-4) : SETUP B switch
Used for maintenance purpose.
MVE-8000A
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. VIF-32/IF-961 board (MVE-8000A)
6
5
4
3
2
1
4
3
2
1
E502
E501
TP801
TP805
TP804
A
B
D13
D10
1
2
TP803
TP802
A
SW1
SW2
CPU-DR
Module
3
4
D7
D6
D5
D17
D16
D15
D14
D19
D18
E1
B
C
CN3
5
6
D12
C
D
CN4
G
F
E
D
C
B
A
S1
D8
S901
D9
D10
D11
S2
CN1501
TP301
D1001
D1002
E504
ND2
ND1
E503
D1003
D1004
TP1101
TP1102
TP1103
TP1104
E
F
E2
D1
TP2
D
TP601
E301
TP502
D502
TP503
TP201
D503
TP501
TP1
D501
TP504
D504
D2
D3
E
F
D4 G
D12
D13
D14
D15
E201
CN5
E3
TP401
E506
H
J
G
E505
E401
VIF-32 board
IF-961 board
A side/Component side
D1001 (C1) : BOOT DONE
Lights when booting is completed.
[VIF-32 board]
<LED>
D501 (E1) : +3.3 V
D1002 (D1) : DLKD status LED
+3.3 V power supply status indication.
Lights when the DLL of the FPGA is locked.
If this LED does not light, the FPGA may be defective.
Lights when the +3.3 V power is supplied.
D502 (E1) : +2.5 V
D1003 (D1) : RCB DONE status LED
Lights when the FPGA configuration is completed.
+2.5 V power supply status indication.
Lights when the +2.5 V power is supplied.
D1004 (D1) : SYSTEM status LED
Lights when the system configuration and FPGA reset are
completed.
D503 (E1) : +1.5 V
+1.5 V power supply status indication.
Lights when the +1.5 V power is supplied.
If this LED does not light, the FPGA may be defective.
D504 (E1) : +12 V
<Switch>
S901 (C1) : CPU A CONFIG switch
Used for maintenance.
+12 V power supply status indication.
Lights when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
MVE-8000A
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
<Connector>
<LEDs on the CPU-DR module>
Refer to <LEDs on the CPU-DR module> in “1. CA-
54CFC Board”.
CN1501 (C1) : ISP common connector
Used for writing a program in the JTAG device with ISP in
the production process.
<Switches on the CPU-DR module>
Refer to < Switches on the CPU-DR module> in “1. CA-
54CFC Board”.
<TEST terminals>
E201 (F1), E301 (E1), E401 (G2), E501 (A6),
E502 (A1), E503 (D6), E504 (D3), E505 (G5),
E506 (F3) : GND terminals
[IF-961 board]
Used as ground terminals when measuring voltages on the
check terminals.
<LEDs>
D1 (E1) : +12 V
+12 V power supply status indication.
Lights when the +12 V power is supplied.
If this LED does not light, the fuse may have blown.
TP401 (F1), TP501 (E1) : +3.3 V check terminal
+3.3 V measuring terminal.
TP301 (D1), TP502 (D1) : +2.5 V check terminal
D2 (G1) : +3.3 V
+2.5 V measuring terminal.
+3.3 V power supply status indication.
Lights when the +3.3 V power is supplied.
TP201 (E1), TP503 (E1) : +1.5 V check terminal
+1.5 V measuring terminal.
D3 (G2) : +2.5 V
+2.5 V power supply status indication.
Lights when the +2.5 V power is supplied.
TP504 (E1) : +12 V check terminal
+12 V measuring terminal.
D4 (G3) : +1.5 V
TP601 (D2) : Check terminal
Used for design purpose.
+1.5 V power supply status indication.
Lights when the +1.5 V power is supplied.
TP801 (A5) : CK (clock) signal check terminal
D5 (B1) : BUS A
Used for checking the CK signal from the motherboard.
Used for design purpose. (Not lid in normal operation)
TP802 (A5) : FD signal check terminal
D6 (B1) : BUS B
Used for checking the FD signal from the motherboard.
Used for design purpose. (Not lid in normal operation)
TP803 (A5) : CKX (control timing) signal check
terminal
D7 (B1) : READ
Used for design purpose. (Not lid in normal operation)
Used for checking the CKX signal from the motherboard.
D8 (D1) : DBG 7 A
TP804 (A5) : HD (horizontal sync) signal check
terminal
Used for design purpose. (Not lid in normal operation)
Used for checking the HD signal from the motherboard.
D9 (D1) : DBG 6 A
Used for design purpose. (Not lid in normal operation)
TP805 (A5) : VD (vertical sync) signal check
terminal
D10 (D1) : DBG 5 A
Used for checking the VD signal from the motherboard.
Used for design purpose. (Not lid in normal operation)
TP1101 (D1), TP1102 (D1), TP1103 (D1),
TP1104 (D1) : DBG0 - DBG3 check terminals
Used for design purpose.
D11 (D1) : DBG 4 A
Used for design purpose. (Not lid in normal operation)
D12 (G1) : BOOT DONE
Lights when booting is completed.
MVE-8000A
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
D13 (G1) : DLKD status LED
Lights when the DLL of the FPGA is locked.
If this LED does not light, the FPGA may be defective.
D14 (G1) : RCB DONE status LED
Lights when the FPGA configuration is completed.
D15 (G1) : SYSTEM status LED
Lights when the system configuration and FPGA reset are
completed.
If this LED does not light, the FPGA may be defective.
ND1 (E1), ND2 (E2) : STATUS A LED
Indicates status of the VIF-32 board CPU.
<Switches>
S1 (D1) : CPU CONFIG A switch
Used for maintenance.
S2 (D1) : SETUP switch
Used for maintenance.
<Connectors>
CN3 (C1) : COM A terminal
Connected to the SUB CPU control terminal during
maintenance.
RS-232C interface compliant.
CN4 (C1) : USB terminal
Used for maintenance.
CN5 (H1) : ISP common connector
Used for writing a program in the JTAG device with ISP in
the production process.
<Test terminals>
E1 (B1), E2 (E1), E3 (H1) : GND terminals
Used as ground terminals when measuring voltages on the
check terminals.
TP1 (G1) : +3.3 V check terminal
+3.3 V measuring terminal.
TP2 (E1) : +12 V check terminal
+12 V measuring terminal.
MVE-8000A
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
1-9. System Connection
Connection Example of the MVS-8000/8000A System (MKE-8020A Installed)
VTR
DDR
Audio Mixer
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
DME 1B
DME 1A
PERIPH
DCU-2000 Device
Control Unit Pack
Reference
video signal b)
BKS-R Series
HDS-X Series
MKS-8010A System
Control Unit
Reference
video signal b)
Reference
video signal b)
SWITCHER B
SWITCHER A
MVE-8000A-C DME
Processor Pack
Reference video signal b)
BVE-9100 Editing
Control System
Ethernet switch a)
Ethernet switch a)
Cable with BNC
connectors
MDR68-pincable
Cross cable
a) It is recommended that the CTRL and DATA
LAN networks be configured by connecting
separate Ethernet switches for each LAN.
b) Terminate with the supplied 75 Z terminators.
Terminators are supplied in the product
package.
However, it is also possible to make connections c) Supplied with MKE-8020A MVS Interface
for both LANs on a single Ethernet switch. Board Set.
MVE-8000A
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Flow of Video Signals (MKE-8020A Installed)
The figure below shows the flow of video signals in a MVS-8000/8000A system.
MVE-8000A-C DME Processor Pack
SWITCHER B
SWITCHER A
Reference video signal c)
100 to 240 V AC power supply a)
DME 1A
DME 1B
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
Monitor
MONITOR
OUTPUT 1-8
100 to 240 V AC power
supply b)
Camera,
VTR,
routing
switcher
100 to 240 V AC power
supply b)
PRIMARY INPUTS 1-80
OUTPUTS 1-48
100 to 240 V AC power
supply b)
100 to 240 V AC power
supply b)
Reference video signal c)
Monitor
VTR
Video input signal
Video output signal
MDR 68-pin cable d)
Video/key signal
AC power supply
Cable with BNC connectors
a)For the AC power cord of this unit, refer to Section “1-2-2.
Recommended Power Cord” in this manual.
b)For the AC power cord of the MVS-8000/8000A, refer to
“Accessories not supplied” in the MVS-8400/8300/8200/8000/
8000A-C Operation Manual.
c) Terminate with the supplied 75 Z terminators.
Terminators are supplied in the product package.
d) Supplied with MKE-8020A MVS Interface Board Set.
MVE-8000A
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
Service Overview
2-1. Troubleshooting
The main power cannot be turned on. (Indicator does not light green.)
Flow1
The main power of the MVE-8000A cannot be turned on.
(Indicator does not light green.)
YES
NO
Is the POWER switch A of the MVE-8000A turned ON?
YES
Set it to ON.
NO
Is the power cord of the MVE-8000A connected correctly?
YES
Connect it correctly.
The power supply unit is probably defective.
The monitor picture is not displayed correctly.
Flow2
The monitor picture is not displayed correctly even
though the main power of the MVE-8000A is turned on.
YES
NO
Insert the plug-in boards into the correct slots.
(Refer to the MVE-8000A-C Maintenance Manual.)
Are the plug-in boards inserted into their correct slots?
YES
Insert the option boards into the correct slots
respectively. (Refer to Section 1-4.)
NO
Are the option boards inserted into their correct slots?
YES
Connect the input and output cables and equipment
correctly.
NO
Are the input and output cables connected correctly?
YES
NO Install the software correctly.
(Refer to the User s Guide.)
Is the software installed correctly?
YES
NO Start up the system in the Factory Set mode and
check to see.
Is the system set in the Factory Set mode?
YES
* About the Factory Set, refer to Chapter Engineering Setup
of the MVS-8000 System User s Guide.
The MVE-8000A is probably defective.
MVE-8000A
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2. Periodic Inspection and Maintenance
2-2-1. Cleaning
2-3. About the Data Backup Capacitor
A large capacitor is installed on the CA-54CFC board in
order to backup the memory storing the setup and other
data in the MVE-8000A. Leave the main power of the
MVE-8000A turned on for an hour or longer in order to
charge this capacitor. The data is backed up for about a
week when the capacitor is fully charged under normal
operating temperature.
Front door assembly
The filter on the rear of the front door assembly can easily
accumulate the dust. Be sure to remove dust by cleaning as
follows.
1. Remove the front door assembly.
(Refer to Section 1-4-1.)
2. Remove the dust accumulated on the filter with a
vacuum cleaner.
n
Cleaning the filter by washing in water is recommend-
ed when there is a heavy accumulation of dust.
Be sure to dry the filter completely after it has been
washed.
Front door assembly
Filters
Fan
If dust has accumulated in the intake of the fan, air is
prevented from flowing smoothly and this may result in a
temperature rise inside the machine. This may have an
adverse effect on performance and the life of the machine.
Cleaning of the fan every month is recommended.
Contact your local Sony Sales Office/Service Center for
information on cleaning the fan.
Fans
MVE-8000A
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
MVE-8000A
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
2004. 7 08
©2004
Sony Corporation
MVE-8000A-C (SY) E
3-855-834-01 (1)
B&P Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|