3-861-541-21 (1)
Trinitron Color
Computer Display
EN
C
Operating Instructions
CPD-100GS
CPD-200GS
© 1998 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Record
The model and serial numbers are located at the rear of the unit.
Record the serial number in the space provided below. Refer to
these numbers whenever you call upon your dealer regarding this
product.
Hinweise
• Aus ergonomischen Gründen wird empfohlen, die
Grundfarbe Blau nicht auf dunklem Untergrund zu
verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu
geringem Zeichenkontrast).
• Aus ergonomischen Gründen (flimmern) sollten nur
Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne
Zeilensprung) verwendet werden.
Model No.
Serial No.
• Die Konvergenz des Bildes kann sich auf Grund des
Magnetfeldes am Ort der Aufstellung aus der korrekten
Grundeinstellung verändern. Zur Korrektur empfiehlt es sich
deshalb, die Regler an der Frontseite für Konvergenz so
einzustellen, daß die getrennt sichtbaren Farblinien für Rot,
Grün und Blau bei z.B. der Darstellung eines Buchstabens zur
Deckung (Konvergenz) gelangen.
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
Dangerously high voltages are present inside
theunit.Donotopenthecabinet.Referservicing
to qualified personnel only.
Siehe hierzu auch die Erklärungen zu Konvergenz.
NOTICE
This notice is applicable for USA/Canada only.
If shipped to USA/Canada, install only a UL LISTED/CSA
LABELLED power supply cord meeting the following
specifications:
FCC Notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
SPECIFICATIONS
Plug Type
Cord
Length
Rating
Nema-Plug 5-15p
Type SVT or SJT, minimum 3 × 18 AWG
Maximum 15 feet
Minimum 7 A, 125 V
NOTICE
Cette notice s’applique aux Etats-Unis et au Canada
uniquement.
Si cet appareil est exporté aux Etats-Unis ou au Canada,
utiliser le cordon d’alimentation portant la mention UL
LISTED/CSA LABELLED et remplissant les conditions
suivantes:
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
SPECIFICATIONS
Type de fiche
Cordon
Longueur
Tension
Fiche Nema 5-15 broches
Type SVT ou SJT, minimum 3 × 18 AWG
Maximum 15 pieds
–
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
Minimum 7 A, 125 V
Declaration of Conformity
As an ENERGY STAR Partner, Sony
Corporation has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
According to 47CFR Parts 2 and 15 for
Class B Personal Computers and Peripherals
Trade Name:
Model No.:
Responsible Party:
Address:
Sony
CPD-100GS and CPD-200GS
Sony Electronics Inc.
1 Sony Drive, Park Ridge,
NJ. 07656
Telephone No.:
201-930-6970
This device complies with Part 15 of the FCC Rules. Each product
marketed, is identical to the representative unit tested and found
tobecompliantwiththestandards. Recordsmaintainedcontinue
to reflect the equipment being produced can be expected to be
within the variation accepted, due to quantity production and
testing on a statistical basis. Operation is subject to the following
two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that cause undesired operation.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
TABLE OF CONTENTS
Getting started
Precautions ........................................................................................................................... 4
Identifying Parts and Controls .......................................................................................... 5
Setup ...................................................................................................................................... 6
Selecting the On-screen Display Language ..................................................................... 6
Connecting Your Monitor’s Speaker................................................................................. 7
Customizing Your Monitor
Adjusting the Picture Brightness and Contrast ............................................................... 8
Introducing the On-screen Display System ..................................................................... 8
Using the CENTER On-screen Display ............................................................................ 9
Using the SIZE On-screen Display .................................................................................... 9
Using the GEOM (Geometry) On-screen Display......................................................... 10
Using the ZOOM On-screen Display.............................................................................. 11
Using the COLOR On-screen Display ............................................................................ 11
Using the SCREEN On-screen Display........................................................................... 12
Using the OPTION On-screen Display........................................................................... 13
Resetting the Adjustments ............................................................................................... 15
Selecting the Graphic Picture Enhancement (GPE) Mode ........................................... 16
EN
Technical Features
Preset and User Modes ..................................................................................................... 16
Displaying the monitor’s information ............................................................................ 17
Power Saving Function ..................................................................................................... 17
Damper Wires .................................................................................................................... 17
Plug & Play ......................................................................................................................... 17
Additional Information
Warning Messages ............................................................................................................. 18
Troubleshooting ................................................................................................................. 18
Self-diagnosis Function ..................................................................................................... 20
Specifications ...................................................................................................................... 20
•
•
•
Macintosh is a trademark licensed to Apple Computer, Inc., registered
in the U.S.A. and other countries.
Windows® is a registered trademark of Microsoft Corporation in the
United States and other countries.
IBM PC/AT and VGA are registered trademarks of International
Business Machines Corporation of the U.S.A.
•
•
VESA is a trademark of Video Electronics Standard Association.
All other product names mentioned herein may be the trademarks or
registered trademarks of their respective companies.
Furthermore, “™” and “®" are not mentioned in each case in this
manual.
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Warning on power connection
Precautions
• Use an appropriate power cord for your local power
supply.
Installation
• Before disconnecting the power cord, wait at least 30
seconds after turning off the power to allow the static
electricity on the CRT display surface to discharge.
• After the power has been turned on, the CRT is
demagnetized (degaussed) for about 5 seconds. This
generates a strong magnetic field around the metal frame,
which may affect the data stored on magnetic tapes and
disks near the bezel. Place magnetic recording equipment,
tapes and disks away from this monitor.
• Prevent internal heat build-up by allowing adequate air
circulation. Do not place the monitor on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
• Do not install the monitor near heat sources such as
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or shock.
• Do not place the monitor near equipment which generates
magnetism, such as a transformer or high voltage power
lines.
The outlet should be installed near the equipment
and be easily accessible.
Maintenance
• Clean the cabinet, panel and controls with a soft cloth
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent,
such as alcohol or benzine.
• Do not rub, touch, or tap the surface of the screen with
sharp or abrasive items such as a ballpoint pen or
screwdriver. This type of contact may result in a scratched
picture tube.
• Clean the screen with a soft cloth. If you use a glass
cleaning liquid, do not use any type of cleaner containing
an anti-static solution or similar additive as this may
scratch the screen’s coating.
Transportation
When you transport this monitor for repair or shipment, use
the original carton and packing materials.
Use of the Tilt-Swivel
With the tilt-swivel, this monitor can be adjusted to the
desired angle within 180° horizontally and 20° vertically.
To turn the monitor vertically and horizontally, hold it at
the bottom with both hands as illustrated below.
15°
90°
90°
5°
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Identifying Parts and Controls
See the pages in parentheses for further details.
Front
Rear
1 MUTING button (page 7)
8 AC IN connector
Mutes the sound.
Provides AC power to the monitor.
EN
2 RESET button (page 15)
9 Video input connector (HD15)
Resets the adjustments to the factory settings.
Inputs RGB video signals and SYNC signals.
3 GPE button (page 16)
Selects the Graphic Picture Enhancement (GPE) mode.
Side
4 MENU button (pages 7 -15, 17)
Displays the MENU OSD.
5 > (contrast) (?//) buttons (pages 7 – 15,
20)
AUDIO
IN
Adjust the contrast.
Function as the (?//) buttons when adjusting other
items.
6 ¨ (brightness) (./>) buttons (pages 7 –
15)
Adjust the picture brightness.
Function as the (./>) buttons when adjusting other
items.
!º AUDIO IN jack
Inputs audio signals when connected to the computer’s
7 u (power) switch and indicator (pages 17,
20)
audio out jack.
Turns the monitor on or off.
!¡ 2 Headphones jack
The indicator lights up in green when the monitor is
turned on, and either flashes in green and orange or
lights up in orange when the monitor is in power
saving mode.
Outputs audio signals to headphones (not supplied).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
About the supplied Macintosh adapter
The supplied Macintosh adapter is compatible with Macintosh LC,
Performa, Quadra and Power Macintosh series computers.
Macintosh II series and some older versions of Power Book models
may need an adapter with micro switches (not supplied).
Setup
Before using this monitor, check that the following items are
included in your carton:
• Monitor (1)
• Power cord (1)
• Macintosh adapter (1)
• Windows® 95 Monitor Information Disk and its manual
(1)
Note
Do not short the pins of the video signal cable.
• Warranty card (1)
• These operating instructions (1)
• Audio miniplug cord (1)
Step 2: Connect the power cord
With the monitor switched off, connect one end of the
power cord to the monitor and the other end to a power
outlet.
This monitor works with any IBM or compatible system
equipped with VGA or greater graphics capability.
Although this monitor works with other platforms running
at horizontal frequencies between 30 and 70 kHz (CPD-
100GS), 30 and 85 kHz (CPD-200GS), including Macintosh
and Power Macintosh systems, a cable adapter is required.
Please consult your dealer for advice on which adapter is
suitable for your needs.
to a power outlet
to AC IN
Power cord (supplied)
Step 1: Connect the monitor to the
computer
Step 3: Turn on the monitor and computer
Connecting to an IBM PC/AT, Macintosh or
compatible computer
The installation of your monitor is complete.
With the computer switched off, connect the video signal
cable to the computer’s video output.
Note
If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on
the screen, see “Warning Messages” on page 18.
For customers using Windows 95
Install the new model information from the “Windows 95 Monitor
Information Disk” into your PC. (Refer to the attached Windows 95
Monitor Information Disk manual.)
IBM PC/AT or
compatible computer
to video output
This monitor complies with the “VESA DDC” Plug&Play standard.
If your PC/graphics board complies with DDC, select “Plug and
Play Monitor (VESA DDC)” as “Monitor type” from “Control
Panel” in Windows 95. Some PCs/graphics boards do not comply
with DDC. Even if your computer complies with DDC, it may have
some problems connecting with this monitor. In this case, select this
monitor‘s model name (CPD-100GS or CPD-200GS) as “Monitor
type” in Windows 95.
Macintosh or
compatible computer
to video output
Macintosh adapter
(supplied)
Selecting the On-screen Display
Language
If you need to change the OSD language, see “Selecting the
on-screen display language” on page 15.
The default setting is English.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
3 Press the >?// buttons to adjust the volume.
Connecting Your Monitor’s
Speaker
You can listen to music, sounds, and other audio files using
the speaker in your monitor.
Connect the AUDIO IN jack to the audio out jack of your
computer’s sound card using the miniplug cord (supplied).
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
To mute the sound
AUDIO
IN
Press the MUTING button.
No sound comes from the speaker.
The
mark appears at the bottom of the screen.
AUDIO IN jack
2 Headphones jack
MUTING
Adjusting the sound
EN
1 Press the MENU button.
To cancel, press the MUTING button again.
The MENU OSD appears.
MENU
MENU
OK
Using the headphones jack
COLOR CENTER SCREEN
MENU
You can listen to the audio signals from your computer
using headphones (not supplied). The speaker turns off
when headphones are connected to the headphones jack.
Adjust the volume using the SOUND OSD.
GEOM
EXIT
SIZE
ZOOM
SOUND
OPTION
2 Press the ¨./> and >?// buttons to select “™
SOUND,” and press the MENU button again.
The SOUND OSD appears.
Note
If the volume from the speaker is too low, increase the output level
(average of 500 mv) of the computer.
SOUND
26
Note
While muting the sound, the
mark appears in the SOUND OSD
instead of the Á mark. Increase the volume to cancel the
mark
and activate the speaker.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
Before adjusting
• Connect the monitor and the computer, and turn them on.
• Select “ (LANGUAGE)” in the OPTION OSD, then
select “ENG” (English) (see page 15).
Introducing the On-screen
Display System
Most adjustments are made using the MENU OSD.
Adjusting the Picture Brightness
and Contrast
MENU OSD
Press the MENU button to display the MENU OSD.
This MENU OSD contains links to the other OSDs described
below.
Once the setting is adjusted , it will be stored in memory for
all input signals received.
1 Press the ¨ (brightness) ./> or > (contrast) ?//
buttons.
MENU
MENU
OK
The BRIGHTNESS/CONTRAST OSD appears.
MENU
COLOR CENTER SCREEN
BRIGHTNESS/CONTRAST
GEOM
EXIT
SIZE
ZOOM
26
26
60.0kHz/ 85Hz
SOUND
OPTION
Horizontal
Vertical
Frequency* Frequency*
2 For brightness adjustment
1
2
3
4
5
COLOR
Press the ¨./> buttons.
Displays the COLOR OSD for adjusting the color
temperature.
> . . . for more brightness
. . . . for less brightness
CENTER
Displays the CENTER OSD for adjusting the centering
of the picture.
For contrast adjustment
Press the >?// buttons.
SCREEN
Displays the SCREEN OSD for adjusting the vertical
and horizontal convergence, etc.
ZOOM
/ . . . for more contrast
? . . . for less contrast
Displays the ZOOM OSD for enlarging and reducing
the picture.
OPTION
Displays the OPTION OSD for adjusting the OSD
position, degaussing the screen, selecting the OSD
language, etc.
The OSD automatically disappears after about 3 seconds.
To reset, press the RESET button while the OSD is on. The
brightness and contrast are both reset to the factory settings.
6
SIZE
Displays the SIZE OSD for adjusting the picture size.
*
The horizontal and vertical frequencies for the received input
signal appear in the BRIGHTNESS/CONTRAST OSD.
7 ™ SOUND
Displays the SOUND OSD for adjusting the sound.
8
GEOM
Displays the GEOMETRY OSD for adjusting the picture
rotation and pincushion, etc.
9 EXIT
Closes the MENU OSD.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
Using the CENTER On-screen
Display
Using the SIZE On-screen Display
The SIZE settings allow you to adjust the size of the picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
The CENTER settings allow you to adjust the centering of
the picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
1 Press the MENU button.
The MENU OSD appears.
1 Press the MENU button.
MENU
The MENU OSD appears.
MENU
2 Press the ¨./> and >?// buttons to select “
SIZE,” and press the MENU button again.
The SIZE OSD appears.
2 Press the ¨./> and >?// buttons to select “
CENTER,” and press the MENU button again.
The CENTER OSD appears.
SIZE
73
CENTER
73
26
EN
26
3 For horizontal adjustment
Press the >?// buttons.
3 For horizontal adjustment
Press the >?// buttons.
/ . . . to increase picture size
? . . . to decrease picture size
/ . . . to move the picture right
? . . . to move the picture left
For vertical adjustment
Press the ¨./> buttons.
For vertical adjustment
Press the ¨./> buttons.
> . . . to increase picture size
. . . . to decrease picture size
> . . . to move the picture up
. . . . to move the picture down
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The horizontal and vertical sizes are both reset to the factory
settings.
To reset, press the RESET button while the OSD is on.
The horizontal and vertical centerings are both reset to the
factory settings.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
4 Press the >?// buttons to adjust the settings.
Using the GEOM (Geometry) On-
screen Display
The GEOM (geometry) settings allow you to adjust the
shape and orientation of the picture.
Once the rotation is adjusted, it will be stored in memory for
all input signals received. All other adjustments will be
stored in memory for the current input signal.
For
Press
ROTATION
/ . . . to rotate the picture clockwise
1 Press the MENU button.
The MENU OSD appears.
? . . . to rotate the picture counterclockwise
MENU
PINCUSHION
/ . . . to expand the picture sides
2 Press the ¨./> and >?// buttons to select “
GEOM,” and press the MENU button again.
The GEOMETRY OSD appears.
? . . . to contract the picture sides
GEOMETRY
/ . . . to move the picture sides to the right
PIN BALANCE
KEYSTONE
26
? . . . to move the picture sides to the left
ROTATION
3 Press the ¨./> buttons to select the item you want
/ . . . to increase the picture width at the
to adjust.
top
? . . . to decrease the picture width at the
top
/ . . . to move the top of the picture to
Select
To
KEY BALANCE
the right
ROTATION
adjust the picture rotation
adjust the picture sides
adjust the picture side balance
adjust the picture width
adjust the picture shape balance
PINCUSHION
PIN BALANCE
KEYSTONE
? . . . to move the top of the picture to
the left
KEY BALANCE
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The selected item is reset to the factory setting.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
Using the ZOOM On-screen
Display
Using the COLOR On-screen
Display
You can change the monitor’s color temperature. For
example, you can change the colors of a picture on the
screen to match the actual colors of the printed picture.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
The ZOOM settings allow you to enlarge or reduce the
picture.
Once the setting is adjusted, it will be stored in memory for
the current input signal.
1 Press the MENU button.
1 Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
MENU
MENU
2 Press the ¨./> and >?// buttons to select “
ZOOM,” and press the MENU button again.
The ZOOM OSD appears.
2 Press the ¨./> and >?// buttons to select “
COLOR,” and press the MENU button again.
The COLOR OSD appears.
ZOOM
COLOR
9300K
5000K
EN
H
V
26
73
3 Press the >?//buttons to adjust the picture zoom.
If you are using Graphic Picture Enhancement (GPE)
If you are in one of the GPE modes, the following
/ . . . to enlarge the picture
? . . . to reduce the picture
COLOR OSD appears when “
COLOR” is selected.
COLOR
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
26
To reset, press the RESET button while the OSD is on.
Note
The picture zoom adjustment will stop as soon as either the
horizontal or vertical size reaches its maximum or minimum value.
This OSD allows you to reduce the color temperature
from 11,000K to 9,300K. Press the >?// buttons to
adjust the color temperature.
For more information on using GPE, see “Selecting the
Graphic Picture Enhancement (GPE) Mode” on page 16.
(continued)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
3 Press the ¨./> buttons to select the color
temperature.
Using the SCREEN On-screen
Display
Adjust convergence settings to eliminate red or blue
shadows that may appear around objects on the screen.
Adjust the CANCEL MOIRE function to eliminate wavy or
elliptical lines that may appear on the screen.
Once the setting is adjusted, it will be stored in memory for
all input signals received.
There are two color temperature modes in the OSD.
The preset adjustments are 9,300K and 5,000K.
Selecting your own color temperature between
9,300K and 5,000K
Press the ¨./> buttons to select “ (VARIABLE)”
and adjust by pressing the >?// buttons.
1 Press the MENU button.
The MENU OSD appears.
MENU
COLOR
9300K
5000K
50
2 Press the ¨./> and >?// buttons to select “
SCREEN,” and press the MENU button again.
The SCREEN OSD appears.
VARIABLE
/ . . . for a higher temperature (bluish)
SCREEN
? . . . for a lower temperature (reddish)
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
26
CONVERGENCE
H
To reset, press the RESET button while the OSD is on. The
selected color temperature is reset to the factory settings.
3 Press the ¨./> buttons to select the item you want
to adjust.
Select
To
adjust the horizontal convergence
H CONVERGENCE
V CONVERGENCE
CANCEL MOIRE
adjust the vertical convergence
eliminate elliptical or wavy lines on
the screen
*
adjust the degree of moire
cancellation
MOIRE ADJUST
*
CANCEL MOIRE must be “ON” for “
to appear on the screen.
(MOIRE ADJUST)”
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
4 Press the >?// buttons to adjust the settings.
Using the OPTION On-screen
Display
The OPTION OSD allows you to manually degauss the
screen and adjust settings such as the OSD position and
OSD language. It also allows you to lock the controls.
For
Press
Degaussing the screen
/ . . . to shift red shadows to the right
and blue shadows to the left
H CONVERGENCE
The monitor screen is automatically degaussed
(demagnetized) when the power is turned on.
You can also manually degauss the monitor.
? . . . to shift red shadows to the left
and blue shadows to the right
1 Press the MENU button.
The MENU OSD appears.
/ . . . to shift red shadows up and blue
V CONVERGENCE
shadows down
MENU
? . . . to shift red shadows down and
blue shadows up
2 Press the ¨./> and >?// buttons to select “
OPTION,” and press the MENU button again.
The OPTION OSD appears.
EN
/ . . . to turn CANCEL MOIRE “ON”
OPTION
CANCEL MOIRE
OFF
ON
ON
? . . . to turn CANCEL MOIRE “OFF”
OFF
ON
MANUAL DEGAUSS
3 Press the ¨./> buttons to select “
(MANUAL
/ . . . to increase the moire cancellation
DEGAUSS).”
effect
MOIRE ADJUST
50
? . . . to decrease the moire cancellation
effect
0
4 Press the > / button.
The screen is degaussed for about 5 seconds.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button again.
To reset, press the RESET button while the OSD is on.
The selected item is reset to the factory setting.
If you need to degauss the screen a second time, wait for at
least 20 minutes before repeating the steps above.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the MENU button again.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
Changing the on-screen display position
Locking the controls
You can change the OSD position (for example, when you
want to adjust the picture behind the OSD).
The control lock function disables all of the buttons on the
front panel except the u (power) switch and MENU button.
1 Press the MENU button.
1 Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
MENU
MENU
2 Press the ¨./> and >?// buttons to select “
OPTION,” and press the MENU button again.
The OPTION OSD appears.
2 Press the ¨./> and >?// buttons to select “
OPTION,” and press the MENU button again.
The OPTION OSD appears.
OPTION
OPTION
ON
ON
MANUAL DEGAUSS
MANUAL DEGAUSS
3 Press the ¨./> buttons to select “
(OSD H
POSITION)” or “ (OSD V POSITION).”
3 Press the ¨./> buttons to select “
(CONTROL
Select “
(OSD H POSITION)” to adjust the horizontal
LOCK).”
position.
OPTION
OPTION
OFF
ON
CONTROL LOCK
OSD H POSITION
(OSD V POSITION)” to adjust the vertical
OPTION
Select “
position.
4 Press the >?// buttons to select “ON.”
OSD V POSITION
The OPTION OSD automatically disappears after about 30
seconds.
4 Press the >?// buttons to move the OSD to the
To close the OSD, press the MENU button again.
desired position.
Once you select “ON,” you cannot select any items except
“EXIT” and ”
If you press any button other than the u (power) switch and
MENU button, the mark appears on the screen.
OPTION” in the MENU OSD.
To cancel the control lock
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the MENU button again.
Repeat steps 1 through 3 above and press the >?//
buttons to select “OFF.”
To reset, press the RESET button while the OSD is on.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Your Monitor
Selecting the on-screen display language
Resetting the Adjustments
English, French, German, Spanish and Japanese versions of
the OSDs are available.
Resetting an adjustment item
1 Press the MENU button.
1
2
3
Press the MENU, ¨./> and >?//buttons to select
the OSD containing the item you want to reset.
The MENU OSD appears.
MENU
MENU
Press the ¨./> buttons to select the item you want
to reset.
2 Press the ¨./> and >?// buttons to select “
OPTION,” and press the MENU button again.
The OPTION OSD appears.
OPTION
ON
Press the RESET button.
MANUAL DEGAUSS
RESET
EN
3 Press the ¨./> buttons to select “
(LANGUAGE).”
OPTION
ENG
DEU
JPN
FRA
ESP
Resetting all of the adjustment data for
the current input signal
LANGUAGE
When there is no OSD displayed, press the RESET
button.
All of the adjustments data for the current input signal is
reset to the factory settings.
4 Press the >?// buttons to select the desired
language.
Note that adjustment data not affected by changes in input
signal (OSD language , OSD position and the control lock
function) is not reset to the factory settings.
RESET
ENG: English, FRA: French, DEU: German,
ESP: Spanish, or JPN: Japanese.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the MENU button again.
Resetting all of the adjustment data for all
input signals
To reset to English, press the RESET button while the OSD
is on.
Press and hold the RESET button for more than two
seconds.
All of the adjustment data, including the brightness and
contrast, is reset to the factory settings.
RESET
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Features
Customizing Your Monitor
Selecting the Graphic Picture
Enhancement (GPE) Mode
Preset and User Modes
The monitor has factory preset modes for the 9 (CPD-
100GS) or 10 (CPD-200GS) most popular industry standards
for true “plug and play” capability.
The Graphic Picture Enhancement (GPE) button allows you
to automatically change the characteristics of the picture on
the screen to match the use of your monitor. Simply press
the GPE button to scroll between the three modes.
Recommended horizontal and vertical timing
conditions
Horizontal sync width duty should be 1.0 µsec of total horizontal
time.
1 Turn on the monitor and computer.
2 Press the GPE button to set the mode.
Horizontal blanking width should be ≥3.0 µsec for CPD-200GS.
Horizontal blanking width should be ≥3.6 µsec for CPD-100GS.
Vertical blanking width should be ≥500 µsec for both CPD-100GS
and CPD-200GS.
GPE
Note for Windows® users
For Windows users, check your video board manual or the utility
program which comes with your graphic board and select the
highest available refresh rate to maximize monitor performance.
Each time you press the GPE button, the mode appears on
the screen and changes as follows.
CPD-100GS
Resolution Horizontal Vertical
(dots × lines) Frequency Frequency Mode
Graphics
STANDARD MODE
n
No.
PRESENTATION MODE
GRAPHICS/VIDEO MODE
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
832 × 624
31.5 kHz
43.3 kHz
31.5 kHz
46.9 kHz
53.7 kHz
49.7 kHz
60 Hz
85 Hz
70 Hz
75 Hz
85 Hz
75 Hz
VGA Graphic
VESA
1
2
3
4
5
6
VGA Text
VESA
The STANDARD MODE is ideal for spreadsheets, word
processing, and other text oriented applications.
VESA
Macintosh
16” Color
The PRESENTATION MODE is useful for presentation
programs that require vivid colors.
7
8
9
1024 × 768
1024 × 768
1280 × 1024
60.0 kHz
68.7 kHz
64.0 kHz
75 Hz
85 Hz
60 Hz
VESA
VESA
VESA
The GRAPHICS/VIDEO MODE gives movies and games
enhanced visual appeal by increasing the sharpness and
brightness.
The selected mode indication appears on the screen for
about 3 seconds.
CPD-200GS
Resolution
Vertical
Frequency Mode
Graphics
Horizontal
Frequency
(dots × lines)
No.
If the screen appears too white, adjust the color temperature
as explained in “Using the COLOR On-screen Display” on
page 11.
640 × 480
60 Hz
85 Hz
70 Hz
75 Hz
85 Hz
75 Hz
VGA Graphic
1
31.5 kHz
43.3 kHz
31.5 kHz
46.9 kHz
53.7 kHz
49.7 kHz
640 × 480
720 × 400
800 × 600
800 × 600
832 × 624
VESA
2
3
4
5
6
VGA Text
VESA
Note
The PRESENTATION MODE and GRAPHICS/VIDEO MODE may
produce ghost images when displaying text oriented applications.
These modes change the brightness of the picture dynamically
according to changes in moving pictures. If ghost images appear,
set the GPE to STANDARD MODE.
VESA
Macintosh
16” Color
7
8
1024 × 768
60.0 kHz
60.2 kHz
75 Hz
75 Hz
VESA
1024 × 768
Macintosh
19” Color
1024 × 768
85 Hz
75 Hz
VESA
VESA
9
68.7 kHz
80.0 kHz
1280 × 1024
10
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Features
Displaying the monitor’s
information
Damper Wires
When viewing a white background, very thin horizontal
lines are visible on the screen as shown below. These lines
are damper wires.
The Trinitron tube has a vertically striped aperture grille
inside. The aperture grille allows more light to pass
through to the screen giving the Trinitron CRT more color
and brightness.
You can display the model name, serial number and year of
manufacture using the monitor‘s INFORMATION OSD.
Press and hold the MENU button for 5 seconds.
The INFORMATION OSD appears.
These damper wires are attached to the aperture grille to
prevent vibration of the aperture grille and keep the screen
image constantly stable.
Example:
INFORMATION
MENU
:
MODEL CPD 100GS
Damper wire
:
SER NO 1234567
MANUFACTURED
: 1997
Approx. 6cm
(CPD-200GS
only)
The INFORMATION OSD includes the model name, serial
number and manufactured year.
The OSD automatically disappears after about 30 seconds.
Approx. 6cm
EN
Power Saving Function
This monitor has three modes of reduced power
consumption. By sensing the absence of video signal
coming from the computer, it reduces power consumption
as follows.
Plug & Play
This monitor complies with the DDC 1 and DDC2B
Display Data Channel (DDC) standards of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification Data) to the data line.
Power
Power
Recovery u indicator
consumption consumption time
mode
1
Normal
≤ 120 W
—
Green
operation
(CPD-200GS)
When a DDC2B host system is connected, the monitor
automatically switches to the appropriate standard.
≤ 110 W
(CPD-100GS)
2
3
4
5
Standby
(1st mode)
≤ 15 W
≤ 15 W
≤ 8 W
0 W
Approx.
5 sec.
Green and orange
alternate
DDC is a trademark of the Video Electronics Standard
Association.
Suspend
(2nd mode)
Approx.
5 sec.
Green and orange
alternate
Approx.
15 sec.
Orange
Active-off
(3rd mode)
Power-off
—
Off
Note
If the video signal cable is not connected, the “NO INPUT
SIGNAL” message (page 18) appears. After 30 seconds, the power
saving function automatically puts the monitor into the active-off
mode and the u indicator lights up orange. Once the horizontal
and vertical sync signals are detected, the monitor automatically
resumes its normal operation mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
The input signal condition
Warning Messages
“OUT OF SCAN RANGE” indicates that the input signal
is not supported by the monitor’s specifications.
If there is something wrong with the input signal, one of the
following messages appears.
“NO INPUT SIGNAL” indicates that no signal is input.
INFORMATION
To solve these problems, see “Troubleshooting” below.
Input signal condition
OUT OF SCAN RANGE
Troubleshooting
This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.
Symptom
Check these items
No picture
If the u indicator is not lit
• Check that the power cord is properly connected.
• Check that the u (power) switch is in the “on” position.
If the “NO INPUT SIGNAL” • Try pressing any key on the computer keyboard.
message appears on the • Check that your computer power switch is in the “on” position.
screen, or if the u indicator is • Check that the video signal cable is properly connected and all plugs are firmly seated
either orange or alternating
between green and orange
in their sockets.
• Ensure that no pins are bent or pushed in the HD15 video input connector.
• Check that the video board is completely seated in the proper bus slot.
If the “OUT OF SCAN
RANGE” message appears on
the screen
• Check that the video frequency range is within that specified for the monitor.
Horizontal: 30 – 70 kHz (CPD-100GS), 30 – 85 kHz (CPD-200GS)
Vertical: 50 – 120 Hz
Refer to your computer’s instruction manual to adjust the video frequency range.
• If you are using a video signal cable adapter, check that it is the correct one.
If no message is displayed
and the u indicator is green
or flashing orange
• See “Self-diagnosis Function” (page 20).
Picture is scrambled
• Check your graphics board manual for the proper monitor setting.
• Check this manual and confirm that the graphics mode and the frequency you are
trying to operate at is supported. Even if the frequency is within the proper range,
some video boards may have a sync pulse that is too narrow for the monitor to sync
correctly.
Color is not uniform
• Degauss the monitor (page 13).
If you place equipment which generates a magnetic field, such as a loudspeaker, near
the monitor, or you change the direction of the monitor, color may lose uniformity.
The degauss function demagnetizes the metal frame of the CRT to obtain a neutral
field for uniform color reproduction. If a second degauss cycle is needed, allow a
minimum interval of 20 minutes for the best result.
You cannot adjust the
monitor with the buttons on
the front panel
• If the control lock function is set to on, set it to off using the OPTION OSD (page 14).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Symptom
Check these items
Screen image is not centered • Adjust the size or centering (page 9).
or sized properly
• Some video modes do not fill the screen to the edges. This problem tends to occur with
certain video boards.
• Adjust the geometry (page 10).
Edges of the image are
curved
White lines show red or blue • Adjust the convergence (pages 12 – 13).
shadows at edges
Picture is fuzzy
• Adjust the contrast and brightness (page 8).
• Degauss the monitor (page 13).
If you place equipment which generates a magnetic field, such as a loudspeaker, near
the monitor, or you change the direction of the monitor, color may lose uniformity.
The degauss function demagnetizes the metal frame of the CRT to obtain a neutral
field for uniform color reproduction. If a second degauss cycle is needed, allow a
minimum interval of 20 minutes for the best result.
• If red or blue shadows appear along the edges of images, adjust the convergence
(pages 12 – 13).
• If the moire is cancelled, the picture may become fuzzy. Decrease the moire
cancellation effect (pages 12 – 13).
• Isolate and eliminate any potential sources of electric or magnetic fields. Common
causes for this symptom are electric fans, fluorescent lighting or laser printers.
• If you have another monitor close to this monitor, increase the distance between them
to reduce the interference.
• Try plugging the monitor into a different AC outlet, preferably on a different circuit.
• Try the monitor on a different computer in a different room.
Picture bounces or has wavy
oscillations
EN
Picture is flickering
• Set the refresh rate on the computer to obtain the best possible picture by referring to
your computer’s manual.
Picture appears to be
ghosting
• Eliminate the use of video cable extensions and/or video switch boxes if this symptom
occurs. Excessive cable length or a weak connection can produce this symptom.
Wavy or elliptical (moire)
pattern is visible
• Cancel the moire (pages 12 – 13).
The moire may be modified depending on the connected computer.
• Due to the relationship between resolution, monitor dot pitch and the pitch of some
image patterns, certain screen backgrounds sometimes show moire. Change your
desktop pattern.
• These wires stabilize the vertically striped aperture grille (page 17). This aperture grille
allows more light to pass through to the screen giving the Trinitron CRT more color
and brightness.
Two fine horizontal lines
(wires) are visible
Hum is heard right after the
power is turned on
• When the power is turned on, the auto-degauss cycle is activated. While the auto-
degauss cycle is activated, a hum may be heard. The same hum is heard when the
monitor is manually degaussed. This is not a malfunction.
• If the problem persists, call your authorized Sony dealer from a location near your monitor.
• Note the model name and the serial number of your monitor. Also note the make and name of your video board.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information
Self-diagnosis Function
Specifications
This monitor is equipped with a self-diagnosis function. Use
this function if there is a problem with your monitor or
computer.
CPD-100GS
Picture tube
0.25 mm aperture grille pitch
15 inches measured diagonally
90-degree deflection
Approx. 285 × 214 mm (w/h)
(11 1/4 × 8 1/2 inches)
14.0” viewing image
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 270 × 202 mm (w/h)
(10 3/4 × 8 inches)
1 Disconnect the video input cable or turn off the
connected computer.
Viewable image size
2 Turn the monitor off and on.
Resolution
Standard image area
3 Press and hold the >/ button for 2 seconds.
or
Approx. 253 × 202 mm (w/h)
(10 × 8 inches)
Deflection frequency
Horizontal: 30 to 70 kHz
Vertical: 50 to 120 Hz
0.5W (mono)
If all four color bars appear (white, red, green, blue) after
a few seconds, the monitor is working properly but there
might be a problem with your computer. Contact your
computer’s manufacturer.
Audio output
Headphones jack
Stereo minijack
Accepts impedance of 8 Ω or more
Stereo minijack
AUDIO IN jack
AC input voltage/current
100 to 240 V, 50 – 60 Hz, 1.8 – 1.0 A
Max. 110 W
368 × 392 × 384.5 mm (w/h/d)
(14 1/2 × 15 1/2 × 15 1/4 inches)
Approx. 14 kg (30 lb 14 oz)
See page 6
If the color bars do not appear, there is a potential
monitor failure. Inform your authorized Sony dealer of
the monitor’s condition.
Power consumption
Dimensions
Mass
Supplied accessories
CPD-200GS
Picture tube
0.25 mm aperture grille pitch
17 inches measured diagonally
90-degree deflection
Viewable image size
Approx. 327 × 243 mm (w/h)
(12 7/8 × 9 5/8 inches)
16.0” viewing image
Resolution
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 312 × 234 mm (w/h)
(12 3/8 × 9 1/4 inches)
or
Standard image area
Approx. 293 × 234 mm (w/h)
(11 5/8 × 9 1/4 inches)
Horizontal: 30 to 85 kHz
Vertical: 50 to 120 Hz
0.5W (mono)
Deflection frequency
Audio output
Headphones jack
Stereo minijack
Accepts impedance of 8 Ω or more
Stereo minijack
AUDIO IN jack
AC input voltage/current
100 to 240 V, 50 – 60 Hz, 1.9 – 1.1 A
Max. 120 W
406 × 432 × 420 mm (w/h/d)
(16 × 17 1/8 × 16 5/8 inches)
Approx. 18 kg (39 lb 11 oz)
See page 6
Power consumption
Dimensions
Mass
Supplied accessories
Design and specifications are subject to change without
notice.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|