Portable Basketball System with Elevator-Owners Manual
A Huffy Company
Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A.
WRITE IN YOUR MODEL NUMBER:________________
I M P O RTANT !
In U.S. and Canada only:
Have questions?...don t go back to the store!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although great care and effort have been taken, occasionally problems may occur. To
ensure prompt and correct handling of any problems, or to answer any questions, please contact our Toll-Free Customer Service Number listed below. Service will be quicker if you have your Model Number
(found on carton) and assembly instructions ready when calling. PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
including those used for DISPLAYS,
RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT
MUST be assembled and ballasted with
VOID WARRANTY.
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball Systems,
WARNING
IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
sand or water according to instructions.
Owner must ensure that all players know and
follow these rules for safe operation of the system.
Owner must ensure that all players know and follow
these rules for safe operation of the system.
Failure to follow instructions could result
in SERIOUS INJURY. It is NOT
acceptable to devise a makeshift weight
system.
•
•
DO NOT HANG on the rim or any part of the system
including backboard, support braces or net.
During play, especially when performing dunk type
activities, keep player's face away from the backboard, rim
and net. Serious injury could occur if teeth/face come in
contact with backboard, rim or net.
Do not slide, climb, shake or play on base and/or pole.
After assembly is complete, fill system completely with
water or sand and stake to the ground. Never leave system
in an upright position without filling base with weight, as
system may tip over causing injuries.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Proper and complete assembly,
use and supervision is essential for proper operation and to reduce
the risk of accident or injury. A high probability of serious injury
exists if this system is not installed, maintained, and operated
properly. Check entire box and inside all packing material for parts
•
•
and/or additional instructional material.
Before beginning
assembly, read the instructions and identify parts using the
hardware identifier and parts list in this document.
25
•
When adjusting height or moving system, keep hands and
fingers away from moving parts.
•
•
Do not allow children to move or adjust system.
During play, do not wear jewelry (rings, watches, necklaces,
etc.). Objects may entangle in net.
Surface beneath the base must be smooth and free of
gravel or other sharp objects. Punctures cause leakage and
could cause system to tip over.
Keep organic material away from pole base. Grass, litter,
etc. could cause corrosion and/or deterioration.
Check pole system for signs of corrosion (rust, pitting,
chipping) and repaint with exterior enamel paint. If rust has
penetrated through the steel anywhere, replace pole
immediately.
Check system before each use for proper ballast, loose
hardware, excessive wear and signs corrosion and repair
before use.
Check system before each use for instability.
Do not use system during windy and/or severe weather
conditions; system may tip over. Place system in the
storage position and/or in an area protected from the wind
and free from personal property and/or overhead wires.
Never play on damaged equipment.
See instruction manual for proper installation and
maintenance.
When moving system, use caution to keep mechanism from
shifting.
If using a ladder during assembly, use extreme caution.
Two (2) people are recommended for this operation.
Check base regularly for leakage. Slow leaks could cause system to
tip over unexpectedly.
Seat the pole sections properly (if applicable). Failure to do so could
allow the pole sections to separate during play and/or transport of the
system.
Climate, corrosion or misuse could result in system failure.
Minimum operational height is 6’6" (1.98 m) to the bottom of
backboard.
This equipment is intended for home recreational use only and NOT
excessive competitive play.
•
•
•
REQUIRED TOOLS AND
MATERIALS:
Two People
•
Tape Measure
•
•
Read and understand the warning label affixed to pole. Label is
shown on page 1.
Wood Board (Scrap)
Wrenches: (Two of Each) 7/16 ,
1/2 , 9/16 , 3/4 or Large and
Small Adjustable Wrenches
Sawhorse or Support Table
Garden Hose or Sand (300 lb.)
(136 kg)
The life of your basketball pole depends on many conditions. The
climate, placement of the pole, the location of the pole, exposure to
corrosives such as pesticides, herbicides or salts are all important.
If technical assistance is required, contact Huffy Sports.
Adult supervision is recommended when adjusting height.
•
•
•
•
•
Keep pole top covered with cap at all times.
Do not allow water in tank to freeze. During sub-freezing
weather add non-toxic antifreeze, sand or empty tank
completely and store. (Do not use salt.)
Use extreme caution if placing system on sloped surface.
System may tip over more easily.
Hammer
Tape
Phillips Screwdriver
1/2 & 9/16 Extended Deep
Socket w/ Extension
Recommended
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
•
For more information on assembly, placement, proper use and
maintenance, visit The American Basketball Council website at
The NBA and individual NBA member team identifications reproduced on this product are
trademarks and copyrighted designs, and/or other forms of intellectual property, that are the
exclusive property of NBA Properties, Inc. and the respective NBA member teams and may not
be used, in whole or in part, without the written consent of NBA Properties, Inc.
In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339
201241
2/99
Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339, For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER
Item #7 (1)
Item #8 (1)
Item #11 (1)
Item #9 (1)
Item #12 (6)
Item #13 (2)
Item #15 (2)
Item #16 (10)
Item #18 (5)
Item #20 (12)
Item #17 (2)
Item #28 (2)
Item #30 (1)
Item #31 (4)
* You may have extra parts with this model.
P/N 211999B
12/02
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER
Item #33 (2)
Item #32 (2)
Item #34 (1)
Item #35 (1)
Item #37 (1)
Item #36 (1)
Item #38 (1)
Item #42 (4)
Item #39 (5)
Item #40 (1)
Item #43 (2)
Item #45 (1)
Item #46 (1)
Item #53 (1)
Item #51 (2)
3
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
RIM HARDWARE IDENTIFIER
Item #57 (1)
Item #58 (1)
Item #59 (1)
Item #60 (3)
NOTE: Hardware content may vary. Item #7 201611 or 203104
P/N 211999B
12/02
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS
F
A. Fit left handle (47) onto adjustment tube (49) so the bottom of
adjustment tube (49) sits on the two small ribs of the handle as shown in
figure B.
16. Insert spring (50) into back of locking pin (46) as shown. Spring (50)
should rest between two small ribs at the back of the plastic handle as
shown in Figure C. Insert top of trigger (55) into bracket on the
adjustment tube (49) as shown. The plastic post of the handle pieces
should go through the hole in bottom of trigger (55) and hold it into place
as shown.
17. Finish handle assembly by attaching right handle (48) using screws (18)
as shown.
1. Remove contents from tank (1).
18. Attach adjustment tube (49) to lower elevator tubes (41) using bolt (60)
2. Correctly identify each pole section and mark indicated distance from
spacers (51) and nut (39) as shown.
ends with tape as shown.
19.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
3. IMPORTANT! Center alignment slot of middle pole section (5) in a
lower hole of top pole section (4) as shown. While maintaining
alignment, bounce pole top (4) and middle section (5) together as shown
until they no longer move toward taped reference mark. Upright
assembly. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum
overlap.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED
WHEN EMPTY, MAY TIP OVER.
Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull
trigger to allow lower adjustment rod to move about mid-way into
adjustment tube (49), release the trigger so the lower adjustment rod
(52) locks into position midway inside the adjustment tube (49). Attach
the lower adjustment rod (52) to elevator bracket (27) using bolt (53) and
nut (13) as shown.
4. IMPORTANT! Center alignment slot of lower pole section (6) in a
lower hole of middle pole section (5) as in step 3. While maintaining
alignment, bounce assembly and lower pole section (6) together as
shown until they no longer moved toward taped reference mark.
NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap.
5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8).
20. Fit rim (21) securely into bracket (57) as shown.
Install reinforcement bracket (59) onto T bolt (58) as shown.
6. Install wheel axle (2) through wheel carriage (19) and install wheels (3)
onto wheel axle (2) with spacers (17) as shown. Insert pole assembly
into tank assembly as shown. Secure bottom pole (6) section to tank
and wheel carriage as shown. A deep socket is recommended.
NOTE: Two people recommended for this step.
Install spring (30) onto T bolt (58) as shown.
Install special nut (40) and washer (38) onto T bolt (58).
Tighten nut (40) until flush with end of T bolt (58).
IMPORTANT! DO NOT OVER TIGHTEN.
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS
ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE
TO FOLLOW DIRECTIONS CAREFULLY.
7. Secure base struts (10) to pole using bolt (11), washers (12), and nut
(13), as shown. Rotate the non-secured ends of base struts (10) as
shown.
21. Install net clips as shown. (See illustration)
WARNING: TIGHTEN BOLT (11) IN LOCKNUT (13) UNTIL FLUSH
(EVEN) WITH LOCKNUT S OUTER EDGE.
22. Install net as shown. (See illustration)
8. Secure base struts (10) to base using bolt (15), washers (12), and
23.
WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
nut (16).
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
9. Install pole mount bracket (27) and reinforcement bracket (56) with
carriage bolts (28) as shown. Tighten flange nuts (16) completely.
Roll the completed assembly to the desired playing area. Insert the
T-strap (14) through the slot on the back of the base as shown. Secure
the unit to ground by twisting the tie down stake (23) into the ground and
hooking the T-strap (14) onto the tie down stake (23). Fill tank with 33
gallons of water.
10. Assemble backboard brackets (29) using spacers (33) bolts (34, 35) and
nuts (36, 37) as shown.
11. IMPORTANT! Test fit bolts into holes of backboard brackets(29) and
carefully rock them in a circular motion to ream out paint from holes if
necessary. Attach lower elevator tubes (41) to backboard brackets (29)
using spacers (42) bolt (43) and nut (39) as shown.
IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in
sub-freezing climates.
24. Apply the height adjustment and moving label (25) to the front of the
12.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
pole as shown.
25. Lock elevator system into highest position (so the backboard is as high
as it will go). Apply 10 ft. height indication sticker (54) to adjustment rod
(52) directly below arrow on handle as shown. Move elevator system to
the next position and apply the 91/2 ft. sticker. Repeat until all height
settings have been labeled. (8-10ft.)
Insert T bolt (58) through Slam Jam bracket (57) as shown.
Secure Slam Jam bracket (57) and backboard bracket (29) assemblies
to backboard. Bend upper halves of backboard brackets (29) to line up
with holes in backboard and secure with bolts (32) and nuts (16).
Tighten completely.
26. Pull trigger (55). Move elevator system up or down to desired height,
13. Attach upper elevator tubes (44) to backboard brackets (29) using
release trigger (55) to lock system into one of the five height settings.
spacers (42) bolt (43) and nut (39) as shown.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
14.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
WARRANTY CARD:
Please remember to complete your product
registration form either
on-line at: www.huffysports.com/warrantycard
or mail-in the enclosed postcard.
Support pole on sawhorse. Attach upper and lower elevator tubes (44,
41) to upper pole section (4) using bolts (60) and nuts (39) as shown.
Attach pole cap (22) as shown.
15. Insert locking pin (46) into bracket on adjustment tube (49). Insert cross
pin (45) through hole in bracket and locking pin (46) as shown in figure
5
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
1
1
2
1
1
1
1
1
1
2
1
6
2
1
4
10
4
5
1
12
1
1
1
2
1
1
1
2
2
206669
200628
226401
900217
904840
900136
202820
202822
203063
906206
201625
203218
203220
201568
205528
203100
201651
204804
200627
201219
Tank, (Black)
Wheel Axle
Wheel, 4 (Black)
Top Pole Section
30
31
1
4
203472
203113
Spring, Black, Slam Jam
Bolt, Hex Flange , 5/16-18 x 2 1/2 Long
Bolt, Carriage, 5/16-18 x 2-3/4 Long
Spacer .402 I.D. x.500 O.D. x 1.8 Long
Bolt, Hex 1/4-20 x 2-1/4 Long
Bolt, Hex 3/8-16 x 2.65 Long
Lock Nut 1/4-20
Lock Nut 3/8-16
Washer Flat, Slam Jam
Nut 1/2-13
Nut, Special, Slam Jam
Lower Elevator Tubes
Spacer .530 I.D. x.63 O.D. x .5 Long
Bolt 1/2-13 x 6-5/16 Long
Upper Elevator Tubes
Cross Pin
Locking Pin
Left Handle
Right Handle
Adjustment Tube - Upper
Spring
Spacer .563 I.D. x 1.19 Long
Adjustment Rod - Lower
Bolt 5/16-18 x 1.75 Long
Labels Height Indicator
Trigger
Reinforcement Bracket
Bracket Slam Jam
T-Bolt, 3/8-16 x 5 Large
Bracket, Reinforcement, Slam Jam
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
2
2
1
1
1
1
1
5
1
2
4
5
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
203038
201129
240017
206360
203493
201124
203470
206340
203795
902537
201642
206304
908002
200215
200214
200211
200210
900006
200257
202862
908008
202739
204872
200212
206990
900033
203796
200318
Middle Pole Section
Bottom Pole Section
Rod, 3/8 O.D. x 4-3/4 Long
Eyebolt, 3/8-16 x 2-1/2 Long
Nylon Insert Lock Nut, 3/8-16
Tank Strut
Bolt, Hex Head, 5/16-18 x 3-3/4 Long
Washer, Flat, 3/8 I.D.
Nylon Insert Lock Nut, 5/16-18
Anchor, T-Strap
Bolt, Hex Flange, 5/16-18 x 1 Long
Nut, Hex Flange, 5/16-18
Spacer .500 I.D. x .25 Long
Screw, Phillips Head, 3/4 Long
Wheel Bracket
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Clip, Net Holder
Rim
Cap, Pole Top 3
Stake, Tie Down
206219
203124
203617
211262
Plug Cap
Label, Height Adjustment and Moving
Net
Pole Mount Bracket
Bolt, Carriage, 5/16-18 x 3.5 Long
Backboard Bracket
200209
203231
900846
NOTE: Hardware kit is designed for more than one style of basketball system.
Not all hardware will be used.
P/N 211999B
12/02
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL
4
TOP POLE 31
1.
2.
1
5
MIDDLE POLE 43
BOTTOM POLE 43
6
3.
4.
4
IMPORTANT!
(See Text Page)
5
5
Note
IMPORTANT!
(See Text Page)
(See Text Page)
4
Note
6
(See Text Page)
WOOD SCRAP
WOOD SCRAP
7
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
6
5.
6.
6
7
7
8
IMPORTANT!
8
(See Text Page)
Note
9
(See Text Page)
19
17
3
17
3
2
7.
12
12
6
13
11
10
6
10
1
10
P/N 211999B
12/02
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
10
15
12
1
12
16
9.
5
28
27
56
16
9
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
29
29
36
37
33
34
33
35
11.
29
39
42
41
42
43
41
P/N 211999B
12/02
10
Download from Www.Somanuals.com. All Manuals Search And Download.
16
12.
29
Backboard Style
May Vary
16
41
58
32
57
31
39
13.
44
42
42
43
44
11
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
14.
39
39
44
41
4
22
44
41
43
43
P/N 211999B
12/02
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. A
15.
IMPORTANT!
(See Text Page)
45
49
45
46
49
47
Fig. B
49
47
13
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
16.
IMPORTANT!
(See Text Page)
46
49
50
55
Fig. C
46
50
47
47
P/N 211999B
12/02
14
Download from Www.Somanuals.com. All Manuals Search And Download.
18
18.
17.
18
48
43
47
49
51
41
18
18
51
18
39
19.
WARNING
SEE TEXT PAGE
49
52
27
53
52
13
15
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
20.
21
40
38
30
57
59
P/N 211999B
12/02
16
Download from Www.Somanuals.com. All Manuals Search And Download.
21.
Install net clips.
WARNING: Use of this product without proper installation of net
clips, or when all net clips are not present could result in bodily harm. Be sure
to follow directions carefully.
CLIP ARM
CLIP BODY
21
Insert one arm of clip into ram as shown. Twist body of clip slightly so that
second arm slides over the top of the first arm as shown.
Push in direction indicated by arrows.
A
20
Push second arm back and into ram as shown.
B
Twist body of clip slightly again to spread arms of clip.
Clip arms must be flat and touching edge to edge as shown, not overlapping.
C
17
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
22.
21
Install net.
SIDE VIEW
26
20
NETCLIP
NET
Insert net into bottom of clip as shown.
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
P/N 211999B
12/02
18
Download from Www.Somanuals.com. All Manuals Search And Download.
23.
24
24.
WARNING
SEE TEXT PAGE
24
14
25
10 ft.
(3.05 m)
IMPORTANT!
(See Text Page)
23
HEIGHT ADJUSTMENT STICKERS
HEIGHT ADJUSTMENT
26.
25.
WARNING
SEE TEXT PAGE
54
55
52
19
12/02
P/N 211999B
Download from Www.Somanuals.com. All Manuals Search And Download.
|