ATTACHMENT
OPERATOR’S MANUAL
36” Rotary Tiller
36” Rotary Tiller Attachment
(for use with Conquest / 1700 / 2700, Prestige / 1800 / 2800
& Snapper YT400 and GT500 Series Garden Tractors)
Mfg. No.
1695419
1694151
Description
36” Tiller
36” Tiller
CAUTION: Read and
follow all instructions.
Manual Part No. 1723861
Revision 04
Rev. Date 06/2008
TP 100-2604-04-AT-UV
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Read the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Risks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Identification Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Rules and Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Initial Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Initial Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Differential Lock Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Manual Lift Linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Install the Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Install the Pulley Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Install the Rear Idler Pulley Assembly (Select Models) . . . . . . . . . . . . . . . 11
Install the Lift Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Install the Tiller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Install the Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Storage and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Daily Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Normal Removal and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Normal Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting, Adjustments, and Service . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Tine Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Lift Height and Assist Spring Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . 19
Hardware Chart and Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . 20
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
Operating Safety
Congratulations on purchasing a superior-quality piece of lawn
and garden equipment. Our products are designed and
manufactured to meet or exceed all industry standards for safety.
Power equipment is only as safe as the operator. If it is misused,
or not properly maintained, it can be dangerous! Remember, you
are responsible for your safety and that of those around you.
Use common sense, and think through what you are doing. If you
are not sure that the task you are about to perform can be safely
done with the equipment you have chosen, ask a
professional: contact your local authorized dealer.
Read the Manual
The operator’s manual contains important safety information you need to be aware of
BEFORE you operate your unit as well as DURING operation.
Safe operating techniques, an explanation of the product’s features and
controls, and maintenance information is included to help you get the
most out of your equipment investment.
Be sure to completely read the Safety Rules and Information found on
the following pages. Also completely read the Operation section.
Children
Reverse
Tragic accidents can occur with children. Do not allow
them anywhere near the area of operation. Children are
often attracted to the unit and mowing activity. Never
assume that children will remain where you last saw them.
If there is a risk that children may enter the area where you
are mowing, have another responsible adult watch them.
Do not operate the tiller in reverse
unless absolutely necessary. Always
look down and behind before
and while traveling in
reverse even with the
tiller disengaged.
DO NOT GIVE CHILDREN RIDES ON THIS UNIT! This
encourages them to come near the unit in the future while it
is running, and they could be seriously hurt. They may then
approach the unit for a ride when you are not expecting it,
and you may run over them.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules and Information
Slope Operation
You could be seriously injured or even killed if you use this unit on too
steep an incline. Using the unit on a slope that is too steep or where
you don’t have adequate traction can cause you to lose control or roll
over.
A good rule of thumb is to not operate on any slope you cannot back up
(in 2-wheel drive mode). You should not operate on inclines with a
slope greater than a 3.5 foot rise over a 20 foot length. Always drive up
and down slopes: never cross the face.
Also note that the surface you are driving on can greatly impact stability
and control. Wet grass or icy pavement can seriously affect your ability
to control the unit.
If you feel unsure about operating the unit on an incline, don’t do it. It’s
not worth the risk.
Moving Parts
This equipment has many moving parts that can injure you or someone else.
However, if you are seated in the seat properly, and follow all the rules in this
book, the unit is safe to operate.
Do not allow anyone near the equipment while it is running!
To help you, the operator, use this equipment safely, it is equipped with an
operator-present safety system. Do NOT attempt to alter or bypass the system.
See your dealer immediately if the system does not pass all the safety interlock
system tests found in this manual.
Thrown Objects
This unit has spinning mower blades. These blades can pick up and throw
debris that could seriously injure a bystander. Be sure to clean up the area to
be mowed BEFORE you start mowing.
Do not operate this unit without the entire grass catcher or discharge guard
(deflector) in place.
Also, do not allow anyone in the area while the unit is running! If someone
does enter the area, shut the unit off immediately until they leave.
Maintenance
Proper maintenance is critical to the safety and performance of your unit.
Be sure to perform the maintenance procedures listed in this manual,
especially periodically testing the safety system.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules & Information
This machine is capable to amputating hands and feet and throwing objects. Read these safety rules
and follow them closely. Failure to obey these rules could result in loss of control of unit, severe
personal injury or death to you, or bystanders, or damage to property or equipment.
text signifies important cautions or warnings which must be followed.
The triangle in
TRAINING
OPERATION
1. Read, understand, and follow all instructions on the
machine and in the manuals before operating this
unit. Be thoroughly familiar with the controls and
the proper use of the equipment. Know how to
stop the unit and disengage the controls quickly.
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment
without proper instruction.
1. Do not put hands or feet near or under rotating
parts. Keep clear of the discharge opening at all
times.
2. Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert
for hidden hazards or traffic.
3. After striking a foreign object, stop the engine
(motor), remove the wire from the spark plug,
disconnect the cord on electric motors, thoroughly
inspect the tiller for any damage, and repair the
damage before restarting and operating the tiller.
4. If the unit should start to vibrate abnormally, stop
the engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5. Stop the engine (motor) whenever you leave the
operating position, before unclogging the tiller, and
when making any repairs, adjustments, or
inspections.
6. When cleaning, repairing, or inspecting make
certain the tiller and all moving parts have stopped.
Disconnect the spark plug wire and keep the wire
away from the plug to prevent accidental starting.
7. Do not run the engine indoors except for starting
the engine or for transporting the snowthrower in or
out of the building. Open the outside doors;
exhaust fumes are dangerous.
8. Exercise extreme caution when operating on
slopes. Do not attempt to clear steep slopes.
9. Never operate the tiller without proper guards
plates, or other safety protective devices in place
and working.
10. Keep children and others away.
11. Do not overload the machine capacity by
attempting to till at too fast a rate.
12. Never operate the machine at high transport
speeds on slippery surfaces. Look behind and use
care when operating in reverse.
13. Disengage the PTO when the tiller is transported or
not in use.
14. Use only attachments and accessories approved
by the manufacturer of the snowthrower (such as
wheel weights, counterweights, or cabs).
15. Never operate the tiller without good visibility or
light.
16. Never touch a hot engine or muffler.
17. Never operate the snowthrower near glass
enclosures, automobiles, window wells, drop-offs,
and the like without proper adjustment of the
discharge angle.
18. Never leave a running unit unattended. Always
disengage the tiller, stop engine, and remove keys.
20. Do not operate the unit while under the influence of
alcohol or drugs.
21. Keep in mind the operator is responsible for
accidents occurring to other people or property.
22. DO NOT wear long scarves or loose clothing that
could become entangled in moving parts.
24. Make sure to remove all obstacles from the area to
be cleared.
3. Keep the area of operation clear of all persons,
particularly small children and pets.
4. Exercise caution to avoid slipping or falling
especially when operating in reverse.
PREPARATION
1. Thoroughly inspect the area where the equipment
is to be used and remove all doormat, sleds,
boards, wires, and other foreign objects.
2. Disengage all clutches and shift into neutral before
starting engine (motor).
3. Do not operate the equipment without wearing
adequate outer garments. Wear footwear that will
improve footing on slippery surfaces. Avoid loose
fitting clothing that can get caught in moving parts.
4. Handle fuel with care; it is highly flammable.
(a) Use an approved fuel container.
(b) Never add fuel to a running engine or hot
engine.
(c) Fill fuel tank outdoors with extreme care.
Never fill fuel tank indoors. Replace fuel cap
securely and wipe up spilled fuel.
(d) Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground, away from
your vehicle, before filling.
(e) When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then
refuel such on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
(f) Keep nozzle in contact with the rim of the fuel
tank or container opening at all times, until
refueling is complete. Do not use a nozzle
lock-open device.
(g) Replace gasoline cap securely and wipe up
spilled fuel.
(h) If fuel is spilled on clothing, change clothing
immediately.
5. Use extension cords and receptacles as specified
by the manufacturer for all units with electric drive
motors or electric starting motors.
6. Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by the manufacturer).
7. Always wear safety glasses or eye shields during
operation or while performing an adjustment or
repair to protect eye from foreign objects that may
be thrown from the machine.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules and Information
8. Components are subject to wear, damage, and
deterioration. Frequently check components and
replace with manufacturer’s recommended parts,
when necessary.
CHILDREN
Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the unit and the operating activity. Never assume that
children will remain where you last saw them.
1. Keep children out of the area and under the
watchful care of another responsible adult.
2. Be alert and turn unit off if children enter the area.
3. Never allow children to operate the unit.
4. Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure
vision.
9. Check control operation frequently. Adjust and
service as required.
10. Use only factory authorized replacement parts
when making repairs.
11. Always comply with factory specifications on all
settings and adjustments.
12. Only authorized service locations should be
utilized for major service and repair requirements.
13. Never attempt to make major repairs on this unit
unless you have been properly trained. Improper
service procedures can result in hazardous
operation, equipment damage and voiding of
manufacturer’s warranty.
SERVICE, MAINTENANCE, AND STORAGE
1. Check shear bolts and other bolts at frequent
intervals for proper tightness to be sure the
equipment is in safe working condition.
2. Always refer to the operator’s manual for important
details if the tiller is to be stored for an extended
period.
14. Check shear bolts and other bolts at frequent
intervals for proper tightness to be sure the
equipment is in safe working condition.
4. Maintain or replace safety and instruction labels as
necessary.
5. Maintain or replace safety and instruction labels as
necessary.
6. Keep nuts and bolts tight and keep equipment in
good condition.
7. Never tamper with safety devices. Check their
proper operation regularly and make necessary
repairs if they are not functioning properly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
INITIAL INSTALLATION
Note: Recommended Accessories
Rear wheel weights and front counterweights are
recommended. For operation on slopes greater than
15% (8.5°), front counterweights are required. Never
operate on slopes greater than 17.6% (10°).
Initial Installation Notes:
• The tiller idler pulley is wired to the tiller for
shipping purposes. USE CAUTION WHEN
CUTTING THE WIRE - THE IDLER ARM IS
UNDER SPRING TENSION.
• Remove the mower deck before beginning to
operate.
Replace Differential Lock Rod
(Early Models Only)
1. Locate the differential lock rod (A, B, Figure 1). If
the rod has no bends in it (B), replace it with the
rod included. If the rod has two bendds (A) it
does not need to be replaced.
B
A
Modify Manual Lift Linkage
(Manual Lift Models Only)
C
1. Place the lift lever in the attachment-raised (back)
position.
C
2. Loosen the manual lift adjustment bolt (A, Figure
2) until the bolt can be slid out of the groove in the
bulkhead.
Figure 1. Replace Differential Lock Rod
A. New Differential Lock Rod
B. Old Differential Lock Rod (Discard)
C. Hair Pin Clip and Washer
3. Remove the pin (A, Figure 3) securing the lift link
(D).
4. Remove the pivot capscrew (B) securing the lift
link (D) to the lift cam (J).
5. Check the front lock plate capscrew (L, Figure 4).
If the bolt is grade 5, replace with the 5/16-18 x 1
grade 8 bolt and whizlock nut provided.
6. Replace the lift link (D, Figure 3) with the new one
provided (D, Figure 4). Be sure to reinstall the lift
assist spring (not shown) in its original orientation.
7. Install the clevis pin (A, Figure 4) in the upper
tiller hole (K) in the lift cam, through the rear hole
in the lift link (D), through the spacer (I), and
secure with the hair pin clip (H).
A
8. Reinstall the manual lift adjustment bolt
(A, Figure 2) in the bulkhead.
Figure 2. Manual Lift Adjustment Bolt
A. Adjustment Bolt
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
M
J
A
L
A
J
K
K
I
I
H
H
B
B
C
C
D
D
E
E
G
F
F
G
Figure 3. Lift Components - Mowing
A. Clevis Pin
B. 5/15-18 x 1 Capscrew (Gr. 5)
C. Washer
Figure 4. Lift Components - Tilling
A. Clevis Pin
B. 5/16-18 x 1 Capscrew (Gr. 5)
C. Washer
D. Lift Link (Original)
E. Lift Lock
F. Lift Lever
D. Lift Link (New)
E. Lift Lock
F. Lift Lever
G. Locknut
H. Hair Pin Clip
I. Spacer
G. Locknut
H. Hair Pin Clip
I. Spacer
J. Lift Cam
K. Mower Hole
J. Lift Cam
K. Tiller Hole
L. 5/16-18 x 1 Capscrew (Gr. 8) (New)
M. Lock Plate
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
Install the Hitches
D
1. Install the lower drawbar hitch (F, Figure 5) on the
outside of the rear frame wrapper (E) and the
hitch support (C) on the inside. Secure both to the
rear frame wrapper (E) using two 5/16-18 x 1-1/4
capscrews (G) and two 5/16-18 nylock nuts (A).
E
C
2. Secure the bottom of the lower hitch (F) to the
drawbar using two 1/2-13 x 1-1/2 capscrews (H),
washers (I), and two 1/2-13 nylock nuts (J).
B
3. Secure the sides of the hitch support (C) using
four 3/8-16 x 1 capscrews (D) and four 3/8-16
nylock nuts (B).
C
B
A
Figure 6. Rear Hitch Installation
A. 1/2-13 x 2 Capscrew
B. Washer
H
C. Spacer
D. Rear Hitch
E. 1/2-13 Nylock Nut
G
E
F
D
4. Install the rear hitch (D, Figure 6) using the holes
shown. Secure with four 1/2-13 x 2” capscrews
(A), washers (B), spacers (C), and nylock nuts
(E).
I
A
J
B
C
Figure 5. Hitch Support and Drawbar Installation
A. 5/16-18 Nylock Nut
B. 3/8-16 Nylock Nut
C. Hitch Support
D. 3/8-16 x 1 Capscrew
E. Frame Wrapper
F. Lower Hitch
G. 5/16-18 x 1-1/4 Capscrew
H. 1/2-13 x 1-1/2 Capscrew
I. 1/2 Washer
J. 1/2-13 Nylock Nut
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
Install the Pulley Assemblies
1. Install the rear pulley assembly (D, Figure 7) into
the left side of the rear hitch (C). Secure the
bottom of the pulley assembly to the lower
drawbar hitch (A) with pin (B).
D
C
Figure 9. Front Idler Pulley Installed
Install the Rear Idler Pulley Assembly
(Select Models)
B
1. Install the rear idler pulley (A, Figure 10) into the
left side of the frame wrapper (B) using a 3/8-16 x
2-1/2 capscrew (C), 3/8 flat washer (D), spacer
(E), and 3/8-16 locking flange nut (F) as shown.
Tighten nut to 19.5 lb-ft (26.5 Nm).
A
Figure 7. Rear Pulley Installation
A. Lower Hitch
B. Clevis Pin
C. Upper Hitch
D. Idler Pulley Assembly
2. Mount the front idler pulley assembly (A, Figure 8)
onto the left stub (B) at the end of the lift
assembly cross-shaft (C).
3. Hook the slot (D) onto the tractor frame as shown
in Figure 9.
B
A
C
F
B
E
C
D
Figure 10. Rear Idler Pulley Installation
A. Idler Pulley
B. Frame Wrapper
C. 3/8-16 x 2-1/2 Capscrew
D. 3/8 Flat Washer
D
A
E. Spacer
F. 3/8-16 Flanged Locknut
Figure 8. Front Idler Pulley Installation
A. Idler Pulley Assembly
B. Left Stub
C. Lift Assembly Cross-shaft
D. Slot
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
A
D
B
C
Figure 11. Lift Linkage Installation
A. Turn Crank
B. Clevis Pin and Safety Clip
C. Lift Rod
D. Front Bracket
Install the Lift Rod
1. Connect the rear of the lift rod (C, Figure 11) to
the upper hitch. Secure with a clevis pin (B) and
safety clip.
A
2. Slide the lift bracket (A, Figure 12) and lift rod
assembly on the right stub at the end of the lift
assembly cross-shaft. Secure with a clevis pin
and hair pin clip (see Figure 12 inset).
Figure 12. Lift Arm Extension Installation
A. Lift Bracket
MANUAL LIFT MODELS ONLY:
3. Mount the front bracket (D, Figure 11) to the
frame using a 5/16-18 x 1 capscrew and nylock
nut.
4. Secure the rear turn crank assembly (A, Figure
11) to the rear hitch using 3/8-16 x 1 carriage bolt
and nylock nut.
5. Hook the spring to the turn crank (A) and put the
threaded rod through the front bracket (D). Turn
the crank until the nut is captured in the front
bracket.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Setup & Installation
Install the Tiller
B
A
1. Position the tiller at the rear hitch and insert the
lift bar (A, Figure 13) into the upper hitch (B).
Secure with a clevis pin and safety clip.
2. Rotate the tiller upward so that the hitch arms (C)
are aligned with the lower hitch (D). Secure with
two clevis pins and safety clips.
D
C
Figure 13. Tiller Installation
A. Lift Bar
B. Upper Hitch
C. Hitch Arm
D. Lower Hitch
E
D
F
F
A. PTO Pulley
B. Front Pulley Assembly
C. Rear Pulley Assembly
D. Tiller Idler Pulley
B
E. Tiller Input Pulley
F. Rear Idler Pulley
A
Figure 14. Belt Routing
3. Install the belt on the front pulley assembly (B) and
PTO pulley (A). Adjust the front pulley assembly
belt guides within 1/16” of the belt.
Install the Belt
1. Remove the spring clip and pin securing the tiller
belt cover. Pivot the belt cover out of the way to
allow access to the tiller pulleys.
4. Route the belt inside the spring-loaded tiller idler
pulley (D).
5. Reposition tiller belt cover and secure with the
clevis pin and spring clip.
2. Install the belt on the rear pulley assembly (C,
Figure 14) and tiller input pulley (E). The smaller
upper and lower pulleys of the rear pulley
assembly (C) should trap the belt in the middle
pulley groove with the belt routed below the rear
idler pulley (F) as shown.
Adjustments
Perform the adjustments found in the “Toubleshoot-
ing, Adjustments, -and Service” section.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
OPERATION
WARNING
Perform the Safety System Interlock test found
in your tractor Operator’s Manual. If tractor
does not pass the test, do not operate the
tractor. See your authorized dealer. Under no
circumstances should you attempt to defeat
the safety system.
NOTICE
Refer to the Tractor Operator’s Manual for
important information concerning safely
operating your tractor.
To prevent an explosion or fire, never store the
tractor with fuel in the tank inside a building
where an ignition source is present.
CAUTION
After striking a foreign object, stop the engine,
disengage the PTO, and remove the key.
Inspect the tiller for damage before starting.
DANGER
OPERATING ON SLOPES
CAN BE DANGEROUS
The tiller may propel the tractor forward when
first lowered into hard ground especially if tiller
depth is set too deep or tractor ground speed
is too fast.
Never operate on slopes greater than 17.6
percent (10°) which is a rise of 3-1/2 feet
vertically in 20 feet horizontally.
Checks Before Starting
1. Make sure all covers and guards are in place.
Make sure all nuts, bolts, clevis pins, and clips
are secure.
Operate the unit at a slow ground speed when
driving onto a slope. Avoid using brakes to
control ground speed.
2. The tiller must be lubricated before first use and
after every four hours of operation. If required,
see instructions in “Maintenance” section.
When operating on slopes that are greater
than 15% (8.5°) but less than 17.6 percent, use
additional wheel weights or counterweights.
3. Clear the work area of any items that could be
caught in the tiller.
In addition to counter weights, use extra
caution when operating on slopes. Drive UP
and DOWN the slope, never across the face,
use caution when changing directions, and
DO NOT START OR STOP ON SLOPE.
Transporting
When transporting the tiller to and from the work
area, the tiller should be fully raised. Adjust ground
speed according to condition of the ground surface.
Starting and Stopping
Turning or Backing When Tilling
Before backing up or turning, raise the tiller until it
clears the ground. Otherwise, the tiller can be
damaged.
To start tilling, engage the tractor PTO then lower the
tiller. Slowly drive forward. The tiller will work into the
soil. Engage the PTO only when the tiller is out of the
ground.
To stop the tiller, raise the tiller, and disengage the
PTO. Raise tiller to transport position before traveling
to and from the work site or storage area.
The weight of the tiller will reduce the weight on the
front tires. Front counterweights are recommended
to restore normal turning ability.
Tilling Suggestions
Engine Speed and Ground Speed
Plan the pattern before beginning. When the land
contour permits, it is best to travel in the longest
direction to minimize turning.
Tilling should always be done with engine speed at
full throttle. If ground speed is too high, slow down.
Do not reduce the engine speed. Refer to the tractor
“Operator’s Manual” for more information on tractor
operation.
The tiller will dig deeper with slow ground speed. It is
best to increase the depth on succeeding passes
until the desired depth is reached. Making passes
crossways to the previous pass usually helps break
sod into fine particles. In soft, loose soil, it may be
possible to till to desired depth in one pass.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage & Maintenance
STORAGE
Daily Storage
Long Term Storage
Note: Refer to the tractor Operator’s Manual for
important information concerning safely storing your
tractor.
1. Use water pressure or brush to thoroughly clean
the unit.
2. Paint, or lightly coat with oil, any area where paint
has been worn or chipped away.
1. Allow tractor engine to cool before storing in any
enclosure.
3. Thoroughly lubricate the unit.
4. Store in a dry place.
2. After jobs are completed, hose or brush down the
unit to remove dirt and debris.
3. Lightly grease or oil all pivot points. Coat bare
metal surfaces to prevent corrosion.
Maintenance Schedule
Schedule
Care Required
MAINTENANCE
After each use.
Clean debris from unit.
Lubricate unit.
Every 5 hours or at least
once a year.
WARNING
Every 50 hours or at
least once a year.
To avoid serious injury, perform maintenance
on the tiller only when the engine is stopped,
parking brake is set, and all moving parts have
stopped. Always remove the ignition key
before beginning maintenance or adjustments
to prevent accidental starting of the engine.
Check drive belt.
Note: Keep grease and oil off belts.
TILLER SHAFT
Note: Keep grease and oil off belt and pulleys.
UNDERSIDE OF TILLER
Symbol
Use
Apply With
Procedure
Lithiium base automotive grease
Grease gun
1. Wipe fitting clean with rag.
2. Apply 2 or 3 shots of grease.
3. Wipe up any excess grease.
SAE 30 Oil
Oil can
Clean indicated area and apply 2
or 3 drops of oil.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal & Normal Installation
REMOVAL
1. Remove the belt from the spring-loaded tiller idler
pulley (D, Figure 15).
E
2. Remove the belt from the PTO pulley (A, Figure
14).
3. Remove the front pulley assembly (B).
4. Remove the pin (B, Figure 16) securing the rear
pulley assembly.
D
F
5. Raise the tiller.
C
B
6. Manual Lift Models: Release the tension on the
lift assist spring (A, Figure 17). Remove the
threaded rod spring (B) from the front bracket.
A
7. Lower the tiller.
Figure 15. Belt Routing
A. PTO Pulley
B. Front Pulley Assembly
C. Rear Pulley Assembly
D. Tiller Idler Pulley
E. Tiller Input Pulley
F. Rear Idler Pulley
8. Remove the lift bracket (A, Figure 18) and lift rod.
9. Detach the tiller from the rear hitches (Figure 18).
10. Manual Lift Models: Switch the lift link from the
tilling position (D, Figure 20) to the mowing
position (C).
NORMAL INSTALLATION
1. Manual Lift Models: Switch the lift link from
mowing position (C, Figure 20) to tilling position
(D).
D
C
2. Attach the tiller to the rear hitch (see Figure 19).
3. Install the lift bracket (A, Figure 18).
4. Install the lift rod (C, Figure 17).
5. Manual Lift Models: Raise the tiller. Install the
lift assist spring assembly (A, B, Figure 18).
B
6. Install the rear pulley assembly (D, Figure 16).
7. Install the front pulley assembly (B, Figure 15).
8. Route the drive belt as shown in Figure 15.
A
9. Perform the adjustments listed in the “Trouble-
shooting, Adjustments, and Service” section.
Figure 16. Install Pulley Assembly
A. Lower Hitch
B. Clevis Pin
C. Upper Hitch
D. Idler Pulley
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal & Normal Installation
B
A
A
B
C
Figure 17. Lift Assist Spring
A. Spring
D
B. Threaded Rod Spring
C. Lift Rod
C
Figure 19. Tiller Assembly
A. Lift Bar
B. Upper Hitch
C. Hitch Arm
D. Lower Hitch
A
D
Figure 18. Lift Arm Extension
A. Lift Bracket
C
A
B
Figure 20. Lift Link Positions-Normal
A. Clevis Pin
B. Spacer and Hair Pin Clip
C. Mowing Position
D. Tilling Position
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
TROUBLESHOOTING
WARNING
Troubleshooting procedures are provided in the
following chart. To use these procedures, first locate
the problem description that best describes the
trouble that you have encountered. Check the
possible causes one at a time in the order that they
are listed. Correct any problems that are found and
try to operate the rotary tiller again to see if you have
eliminated the trouble.
For your safety, do not try to adjust or repair
the tractor or rotary tiller while the engine is
running. Always remove the key from the
ignition switch before beginning maintenance
to prevent accidental starting.
Symptom
Problem
Solution
1 Clean as required.
2 Replace belt.
Rotary tiller tines do not rotate. 1. Drive belt or pulleys oily.
2. Tiller drive belt too loose.
3. Rock jammed in tiller.
3. Remove it.
4. Tiller drive belt broken.
4. Replace as needed.
1. Adjust the attachment lift.
Tills too shallow
1. Tiller depth set too low.
2. Engine RPM speed too low.
3. Tractor ground speed too fast. 3. Slow down.
2. Set engine to full speed.
4. Ground too hard.
4. Make several passes, tilling
deeper on each pass.
Tiller leaves ground rough
with large clods.
1. Ground too wet.
1. Wait until sod does not ball up
when rolled in your hand.
2. Tilling too deep in one pass.
3. Tractor ground speed too fast.
2. Make several passes.
3. Slow down.
Tractor handles poorly.
1. Tractor ground speed too fast. 1. Use slower speed, especially when
running on rough or sloping surfaces.
2. Front wheels lifting.
2. Clean dirt from tiller. Use front wheel
3. Rear wheels slip.
counterweights and weight carrier.
4. Tiller propels tractor.
3. Use chains or wheel weights.
4. Tiller depth set too low.
C
TINE REPLACEMENT
When required because of wear or breakage, replace
a tine as follows.
A
B
1. Remove two capscrews (A, Figure 21) and
locknuts (B).
2. Remove old tine (C) from tiller.
3. Place new tine on mounting plate (D). When
facing front of tiller, be sure tine curves away from
mounting plate with its sharp edge facing
D
rearward when tine nears bottom of travel.
Figure 21. Tine Replacement
A. Capscrew
B. Locknut
4. Insert two capscrews (A) through tine and then
through mounting plate (D). Install and tighten
locknuts (B) to 30 lb-ft (40 Nm).
C. Tine
D. Mounting Plate
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting, Adjustments, & Service
LIFT HEIGHT ADJUSTMENT
(MANUAL LIFT MODELS)
INITIAL ADJUSTMENT
1. Park the unit on level ground.
2. Turn the lift spring assist crank (A, Figure 24) until
the length of threaded rod between the bracket
and end of the threaded rod spring (B) and the
bracket measures 6”.
Note: Lubricate the crank and threaded rod with oil.
3. Fully raise the tiller.
5"
4. Adjust the rear lift rod nuts (B, Figure 23) until the
bottom tines ar 5” above the ground.
5. Adjust the front lift rod nuts (A, Figure 23) until the
rod spring is compressed to a length of 9”.
Figure 22. Lift Height Adjustment
WORKING ADJUSTMENT
The amount of lift assist can be varied based on the
depth of tilling and the hardness of the soil. If more
assist is desired, the turn crank (A, Figure 24) clock-
wise. If more downward force is needed, turn the
crank counterclockwise.
A
B
9"
LIFT HEIGHT ADJUSTMENT
(HYDRAULIC LIFT MODELS)
Figure 23. Lift Rod Spring Adjustment
A. Front Lift Rod Nut
B. Rear Lift Rod Nut
1. Park the unit on level ground.
2. Fully raise the tiller.
3. Adjust the rear lift rod nuts (B, Figure 23) until the
bottom tines are 5” above the ground (Figure 22).
A
B
4. Adjust the front lift rod nuts (A, Figure 23) until the
lift rod spring is compresses to a length of 9”.
6"
Figure 24. Lift Spring Assist Crank
A. Lift Spring Assist Crank
B. Threaded Rod Spring
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Identification & Torque Specifications
Common Hardware Types
Torque Specification Chart
Hex Head Capscrew
FOR STANDARD MACHINE HARDWARE (Tolerance 20%)
Washer
No
Marks
Hardware
Lockwasher
Grade
Carriage Bolt
SAE Grade 2
SAE Grade 5
in/lbs
SAE Grade 8
in/lbs
Hex Nut
Size Of
in/lbs
Hardware ft/lbs
Nm.
2.1
2.3
3.1
3.5
7.6
ft/lbs
Nm.
ft/lbs
Nm.
Standard Hardware Sizing
8-32
8-36
19
20
27
31
66
76
11
12
20
23
30
35
50
55
65
30
31
43
49
8
10
17
19
30
35
50
55
3.4
3.5
4.9
41
43
60
68
12
14
25
27
45
4.6
4.9
6.8
7.7
16.3
19.0
34.0
34.0
61.2
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
5.5
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
10.9
13.6
23.1
25.8
40.8
47.6
68.0
74.8
8.6
15.0
16.3
27.2
31.3
40.8
47.6
68.0
74.8
88.4
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
50
70
80
68.0
95.2
0
108.8
149.6
163.2
204.0
231.2
299.2
326.4
525.0
571.2
816.0
897.6
1/4
75 102.0
90 122.4
110
120
150
180
260
300 408.0
400
440
110
120
150
170
220
240
386
420
600
660
Nut, 1/2”
1/2
Inside
Diameter
149.6
163.2
204.0
244.8
353.6
3/4
75 102.0
90 122.4
100
160 217.6
180 244.8
140
155
220
240
1
2
3
4
136
1/4
1/2
190.4
210.8
299.2
326.4
544.0
598.4
3/4
7/8-14
1-8
1-12
Screw, 1/2 x 2
580 788.8
640
900 1,244.0
Body
Diameter
870.4 1,000 1,360.0
1/4
NOTES
1/2
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
Body
Length
3/4
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
1/4
b. for flange whizlock nuts and screws - use 135% of
1/2
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
3/4
Wrench & Fastener Size Guide
1/2
DIA.
7/16
DIA.
3/8
5/16
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16” Bolt or Nut
Wrench—1/2”
3/8” Bolt or Nut
Wrench—9/16”
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2” Bolt or Nut
Wrench—3/4”
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Briggs & Stratton Power Products Group, L.L.C.
Copyright © 2008 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
|