O
P
E
R
A
T
I
N
G
I
N
S
T
R
U
C
T
I
O
N
S
W
R
A
S
WIDE RANGE AMPLIFIER STAGE
AUDIO/VIDEO SURROUND RECEIVER R-863
MULTI CONTROL
MASTER VOLUME
SOURCE
DIRECT
BAND
T/P MODE
CINEMA EQ
MULTI ROOM
REMOTE SENSOR
LOCK
DYNAMIC
RANGE
TUNING/PRESET
ROOM2 FEED
INPUT SELECTOR
VIDEO TAPE MON.
SURROUND MODE
EXTRA SURR.
POWER
AUDIO
7.1CH DIRECT DECODING
STEREO
DIGITAL/ANALOG
STANDBY
ON/STANDBY
6.1/7.1
ON
/
OFF
PHONES
CHANNEL
SELECTOR
SPEAKER
ON/OFF
TEST TONE
TONE MODE
VIDEO LABEL MEMO/ENTER
-
-
OPTICAL IN S-VIDEO
VIDEO
L
AUDIO
R
R-863
AUDIO/VIDEO SURROUND RECEIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
READ THIS BEFORE OPERATING YOUR UNIT
FOR U.S.A AND CANADA .......................................120 V
FOR OTHER COUNTRIES........................... 115 V/230 V
FOR YOUR SAFETY
FOR YOUR SAFETY
Units shipped to countries other than the above
countries are equipped with an AC voltage selector
switch on the rear panel. Refer to the following
paragraph for the proper setting of this switch.
Units shipped to the U.S.A and Canada are designed
for operation on 120 Volts AC only.
Observe all safety precautions for use of a polarized
AC plug. However, some products may be supplied
with a non polarized plug.
AC VOLTAGE SELECTION
This unit operates on 115/230 V AC. The AC voltage
selector switch on the rear panel is set to the voltage
that prevails in the area to which the unit is shipped.
Before connecting the power cord to your AC outlet,
make sure that the setting position of this switch
matches your line voltage. If not, it must be set to
your voltage in accordance with the following
direction.
CAUTION: To prevent electric shock, match wide
blade of plug to wide slot, insert fully.
FOR EUROPE AND AUSTRALIA ..........230V/240V
FOR YOUR SAFETY
AC voltage selector switch
Units shipped to Australia are designed for operation
on 240 V AC only.
To ensure safe operation, the three-pin plug supplied
must be inserted only into a standard three-pin
power point which is effectively earthed through the
normal household wiring. Extension cords used with
the equipment must be three-core and be correctly
wired to provide connection to earth.
AC 230 V
AC 115 V
Improper extension cords are a major cause of
fatalities. The fact that the equipment operates
satisfactorily does not imply that the power point is
earthed and that the installation is completely safe.
For your safety, if in any doubt about the effective
earthing of the power point, consult a qualified
electrician.
Move switch lever to match your line voltage with a
small screwdriver or other pointed tool.
PAN-EUROPEAN UNIFIED VOLTAGE
All units are suitable for use on supplies 230-240 V
AC.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Introduction
ꢁUNPACKING AND INSTALLATION....................................................................................................... 2
ꢁREAD THIS BEFORE OPERATING YOUR UNIT................................................................................... 3
System Connections........................................................................................................................................ 5
Front Panel Controls...................................................................................................................................... 9
Universal Remote Controls
ꢁDIGI LINK SYSTEM REMOTE CONTROLS......................................................................................... 10
ꢁOPERATING COMPONENTS WITH REMOTE CONTROL................................................................. 12
ꢁREMOTE CONTROL OPERATION RANGE.......................................................................................... 12
ꢁLOADING BATTERIES............................................................................................................................ 12
ꢁADDITIONAL INFORMATION ON REMOTE COMMAND CODES.................................................. 13
ꢁENTERING A SETUP CODE ................................................................................................................... 14
Operations
ꢁLISTENING TO A PROGRAM SOURCE................................................................................................ 15
ꢁSURROUND SOUND................................................................................................................................ 18
ꢁENJOYING SURROUND SOUND........................................................................................................... 21
ꢁLISTENING TO RADIO BROADCASTS................................................................................................ 25
ꢁRECORDING............................................................................................................................................. 27
ꢁDIGITAL AUDIO RECORDING WITH MD RECORDER..................................................................... 28
ꢁOTHER FUNCTIONS................................................................................................................................ 29
ꢁROOM 2 SOURCE PLAYBACK.............................................................................................................. 31
Using the OSD
ꢁCURRENT STATUS DISPLAY................................................................................................................ 32
OSD Menu Settings....................................................................................................................................... 32
ꢁSETTING THE SPEAKER SETUP........................................................................................................... 34
ꢁSETTING THE FUNCTION SELECT...................................................................................................... 37
ꢁSETTING THE SURROUND SETUP....................................................................................................... 41
ꢁSETTING THE CH LEVEL TRIM............................................................................................................ 43
ꢁSETTING THE ROOM2 FEED SETUP.................................................................................................... 44
Troubleshooting Guide ................................................................................................................................ 46
Specifications.................................................................................................................................................. 47
4
Download from Www.Somanuals.com. All Manuals Search And Download.
System Connections
ꢁPlease be certain that the receiver is unplugged from the AC outlet before making any connections.
ꢁBe sure to connect the white RCA pin cords to the L(left) and the red RCA pin cords to the R(right) jacks when making
connections.
ꢁChange the position of the FM indoor antenna until you get the best reception of your favorite FM stations.
ꢁA 75Ω outdoor FM antenna may be used to further improve the reception.
Disconnect the indoor antenna before replacing it with the outdoor one.
ꢁPlace the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a
direction for the best reception.
ꢁIf the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna.
ꢁMake connections firmly and correctly. If not, poor connections can cause loss of sound, noise or damage to the receiver.
ꢁIf the electricity fails or the AC input cord is left unplugged for about two weeks, the memorized contents will be lost.
Should this happen, memorize them again.
ꢀ CONNECTING ANTENNAS
ꢀ CONNECTING AUDIO COMPONENTS
CD player
MULTIPLE COMPACT DISC PLAYER CDC-5080R
OPEN/CLOSE
V
-CD PBC REVERT PROG AUTO
GRAPHICS PEAK DELETE EDIT SCENE TRACK
INDEX STEP
R
A
N
D
O
M
R
E
P
E
A
T
ALL
1
DISC
S
A< >B MPX INTRO
1
4
2
5
8
3
6
POWER
A
B
7
9
ON/OFF
FM
10
1
1
12
1
2
3
4
5
1
3
1
4
1
5
PHONES LEVEL
REMOTE SENSOR
P
R
O
G
R
A
M
/
R
E
V
I
E
W
R
A
N
D
O
M
REPEAT
MIN
MAX
PHONES
(OUTDOOR ANTENNA)
Additional
audio component
PLAY(LINE OUT)
REC(LINE IN)
Tape deck or
MD recorder
FM
AM loop antenna
(INDOOR ANTENNA)
300 ohm
feeder
• The AUX jacks may be connected to an additional audio
component such as CD player or tape deck, etc.
• Connect the TAPE MONITOR IN/OUT jacks to the PLAY(LINE
OUT) / REC(LINE IN) jacks of tape deck, MD recorder or CD
recorder.
• The TAPE MONITOR IN/OUT jacks may also be connected to
the LINE OUT/IN jacks of an optional graphic equalizer.
SUPPLIED ADAPTOR
ꢀ CONNECTING 7.1CH DIRECT INPUTs
SUBWOOFER CH OUT
CENTER CH OUT
Decoder with 5.1
SURROUND BACK CH OUT
or 7.1 channel output
SURROUND CH OUT
FRONT CH OUT
• Use these jacks to connect the corresponding analog outputs of a DVD player or external decoder, etc. that has 5.1 or 7.1 channel
outputs.
• In case of 5.1 channel outputs, do not connect these SURROUND BACK inputs to your audio component. ( For details, refer to
the operating instructions of the component to be connected.)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
CONNECTING VIDEO COMPONENTS
COMPONENT VIDEO OUT
VIDEO IN
S-VIDEO IN
Video deck or
additonal
Monitor TV
video component
MULTIPLE COMPACT DISC PLAYER CDC-5080R
POWER
ON/OFF
V-CD PBC REVERT PROG AUTO
GRAPHICS PEAK DELETE EDIT SCENE TRACK
RANDOM REPEA
T
ALL
1
DISC
S
A< >B MPX INTRO
1
4
7
2
5
8
3
6
9
Green
Blue
A
B
I
N
D
E
X
S
T
E
P
1
0
1
1
1
2
OPEN/CLOSE
1
2
3
4
5
1
3
1
4
1
5
PHONES LEVEL
PHONES
MIN
MAX
COMPONENT VIDEO IN
Red
S-VIDEO IN
VIDEO IN
Green
Blue
S-VIDEO OUT
VIDEO OUT
AUDIO
PLAY(OUT)
Red
DVD player
Green
Blue
MULTIPLE COMPACT DISC PLAYER CDC-5080R
COMPONENT
VIDEO OUT
POWER
ON/OFF
Red
LD player or additonal
video component
1
2
3
4
5
DISC SKIP
MULTIPLE COMPACT DISC PLAYER CDC-5080R
OPEN/CLOSE
PLA
Y
EXCHANGE
Exchange 4
POWER
ON/OFF
Play
1
5
DISC AUTOMATIC DISC LOADING SYSTEM
PHONES LEVEL
REMOTE SENSOR
P
R
O
G
R
A
M
/
R
E
V
I
E
W
R
A
N
D
O
M
REPEAT
MIN
MAX
V-CD PBC REVERT PROG AUTO
GRAPHICS PEAK DELETE EDIT SCENE TRACK
R
A
N
D
O
M
R
E
P
E
A
T
ALL
A< >B MPX INTRO
1
DISC
S
1
4
2
5
8
3
6
A
B
I
N
D
E
X
S
T
E
P
7
9
PHONES
1
2
3
4
5
10
1
1
12
S-VIDEO OUT
VIDEO OUT
AUDIO OUT
1
3
1
4
1
5
AUDIO
REC(IN)
S-VIDEO OUT
VIDEO OUT
AUDIO OUT
• The VIDEO 1 jacks may also be connected to a DVD recorder or other digital video recording component.
For details, refer to the operating instructions of the component to be connected.
• There are three kinds of video jacks (COMPONENT, S, normal (composite)) for connecting video components.
Connect them to the corresponding VIDEO jacks (VIDEO 1~3) respectively according to their capability.
• The VIDEO 2(or VIDEO 3) jacks may also be connected to an additional video component such as a video deck, a cable TV tuner,
an LD player or satellite system, etc.
• This unit incorporates COMPONENT as well as S and normal(composite) VIDEO jacks.
• For your reference, the excellence in picture quality is as follows: "COMPONENT" > "S"> normal(composite) "VIDEO".
• When making COMPONENT VIDEO connections, connect "Y" to "Y", "CB" to "CB" (or "B-Y", "PB") and "CR" to "CR"(or "R-
Y", "PR").
• Signals input into the COMPONENT VIDEO IN jacks will be output in only the MONITOR COMPONENT VIDEO OUT jacks.
• A signal input into the normal(composite) VIDEO IN jack will be output in the normal(composite) VIDEO OUT jacks and a signal
input into the S-VIDEO IN jack will be output in the S-VIDEO OUT jacks.
Notes :
• Neither on-screen display function nor video recording are available when using the COMPONENT VIDEO connections.
• When Sherwood DVD player such as V-756, etc. is connected to the DIGI LINK jack for system control, you should connect the
DVD player to the "VIDEO 2" jacks of this unit. Because, if the PLAY button, etc. is pressed on the DVD player, the VIDEO 2 is
automatically selected as an input source on this unit. Then the playback, etc. starts.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ PRE OUT connections
Power amplifier
Front speakers
Power amplifier
Power amplifier
Power amplifier
Surround speakers
Surround back speakers
Front center speaker
ꢀ CONNECTING SYSTEM CONTROL
Sherwood component
with DIGI LINK II or III
CD player
System
control
cord
Tape deck
Powered subwoofer
Graphic equalizer
DVD player
• Use these jacks when adding additional amplifiers.
• Connect the PRE OUT jacks to the powered speakers or to the
power amplifiers respectively.
• To emphasize the deep bass sounds, connect a powered subwoofer.
• Only when enjoying 6.1 or 7.1 channel surround playback, make the
surround back connections between the audio equipment.
• Connect this jack to the DIGI LINK jack of the
external Sherwood component that uses the DIGI
LINK II or III remote control system.
ꢀ CONNECTING DIGITAL INs and OUT
Component(such as an MD recorder,
CD recorder) with OPTICAL DIGIAL IN
• A digital input should be connected to the components
such as LD player, CD player or DVD player, etc.
capable of outputting DTS, Dolby Digital or PCM format
digital signals,etc.
Component with
OPTICAL DIGITAL OUT
• If the component with OPTICAL IN jack is connected to
the OPTICAL OUT jack of this unit, you can record the
high quality sound of CDs etc. without degradation.
• For details, refer to the operating instructions of the
connected component.
• When making the COAXIAL DIGITAL connection, be
sure to use a 75 Ω COAXIAL cord, not a conventional
AUDIO cord.
Component with
OPTICAL DIGITAL OUT
Component with
COAXIAL DIGITAL OUT
Component with
COAXIAL DIGITAL OUT
• All of the commercially available optical fiber cords
cannot be used for the equipment. If you have a question
about the suitability of a particular cord, please consult
your dealer or nearest service organization.
• The COAXIAL or the OPTICAL DIGITAL OUTs of the
components that are connected to CD, TAPE MONITOR and
VIDEO 1 - VIDEO 4 of this unit can be connected to these
DIGITAL INs.
• After making digital connections, be sure to match the
DIGITAL INs to the corresponding input source respectively.
(For details, refer to "When selecting the DIGITAL IN
SETUP" on page 37.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ ROOM 2 connections
Another room
Monitor TV
VIDEO IN
Speakers
A/V receiver
or amplifier
AUDIO IN
• If another A/V receiver or integrated amplifier, etc. is connected to these jacks, you can play a different program source in another
room as well as one source in the main room at the same time.(For details, refer to "ROOM 2 SOURCE PLAYBACK" on page 31).
• When the multiroom adaptor is connected to control this unit in another room, the ROOM 2 function is more convenient.
Note:
• To minimize hum or noise, use high quality connection cords in such a way that there is no humming or noise.
ꢀ CONNECTING MULTI-ROOM
SYSTEM KIT
Another room
OUT
Adaptor
(Multi-room system kit)
IR receiver
Remote control unit
(Multi room system kit)
• To control this unit from a remote location, connect this jack
to the output of the multi-room adaptor.
For information on the multi-room system kit, contact the
ꢀ CONNECTING SPEAKERS
ꢀ SWITCHED AC OUTLETS
Front right
Front left
• These outlets are switched on(power-on
mode) and off(standby mode) according
to the power control as follows(Maximum
total capacity is 1A, 100W):
Front
center
Standby mode – switched AC outlet off
Power-on mode – switched AC outlet on
Surround
right
ꢀ AC INLET
Surround
left
Plug the supplied AC input cord into this AC
INLET and then into the wall AC outlet.
Surround back
right
Surround back
left
To a wall AC
outlet.
• Never short circuit the + and - speaker wires.
• Be sure to connect speakers firmly and correctly according to the
channel (left and right ) and the polarity ( + and -).
• Be sure to use speakers with the impedance of over 6 Ω.
• Only when enjoying either 6.1 or 7.1 channel surround playback,
connect the surround back left speaker only or both of surround
back speakers.
• Do not use an AC input cord other than the one
supplied with this unit. The AC input cord
supplied is designed for use with this unit and
should not be used with any other device.
Note:
• After installing the speakers, first set the connected speakers to the
desired before operating this receiver.(For details, refer to
"SETTING THE SPEAKER SETUP" on page 34.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Controls
TUNING/PRESET MODE BUTTON
MULTI ROOM
REMOTE SENSOR
BAND BUTTON
CINEMA EQ BUTTON
DYNAMIC RANGE BUTTON
SOURCE DIRECT BUTTON
ROOM 2 BUTTON
TUNING/PRESET UP/DOWN
(
/
) BUTTONS
MASTER VOLUME
CONTROL KNOB
MULTI CONTROL KNOB
E
X
T
E
N
D
E
D
W
R
A
S
WIDE RANGE AMPLIFIER STAGE
AUDIO/VIDEO SURROUND RECEIVER R-863
MULTI CONTROL
MASTER VOLUME
SOURCE
DIRECT
BAND
T/P MODE
CINEMA EQ
MULTI ROOM
REMOTE SENSOR
LOCK
DYNAMIC
RANGE
TUNING/PRESET
ROOM2 FEED
INPUT SELECTOR
SURROUND MODE
EXTRA SURR.
POWER
AUDIO
VIDEO TAPE MON. 7.1CH DIRECT DECODING
STEREO DIGITAL/ANALOG
STANDBY
ON/STANDBY
6.1/7.1
ON
/
OFF
PHONES
CHANNEL
SELECTOR
SPEAKER
ON/OFF
TEST TONE
TONE MODE
VIDEO LABEL MEMO/ENTER
OPTICAL IN S-VIDEO
VIDEO
L
-
AUDIO
-
R
DIGITAL/ANALOG BUTTON
STEREO BUTTON
EXTRA SURROUND 6.1/7.1 BUTTON
HEADPHONE JACK
SPEAKER BUTTON
POWER SWITCH
DECODING MODE BUTTON
7.1 CH DIRECT BUTTON
CHANNEL SELECTOR BUTTON
TEST TONE BUTTON
TAPE MONITOR BUTTON
MEMORY/ENTER BUTTON
VIDEO SELECTOR BUTTON
VIDEO LABEL BUTTON
STANDBY BUTTON/INDICATOR
TONE MODE BUTTON
AUDIO SELECTOR BUTTON
ꢀ FLUORESCENT DISPLAY
ꢀ VIDEO 4 INPUT JACKS
TUNED INDICATOR
STEREO INDICATOR
VIDEO INPUT INDICATORS
ROOM 2 INDICATOR
LOCK INDICATOR
-
-
OPTICAL IN S-VIDEO
VIDEO
L
AUDIO
R
SOURCE DIRECT INDICATOR
Additional video component
AUTO TUNING INDICATOR
AUDIO OUT
VIDEO OUT
OPTICAL OUT
S-VIDEO OUT
SURROUND MODE
INDICATORS
MEMORY INDICATOR
PRESET INDICATOR
TAPE MONITOR
INDICATOR
CHANNEL
INDICATORS
• The VIDEO 4 input jacks may be also connected to an additional video
component such as a camcorder, a video deck or a video game player,
etc.
Use the S-VIDEO jack to make connection to video component with the
S-VIDEO OUT jack.
LOCK
• A signal input into the normal(composite) VIDEO jack will be output
in the normal(composite) VIDEO OUT jacks and a signal input into the
S-VIDEO jack will be output in the S-VIDEO OUT jacks.
• The OPTICAL DIGITAL OUTs of the component that are connected
to CD, TAPE MONITOR and VIDEO 1~VIDEO 4 of this unit can be
connected to this OPTICAL IN.
• After making digital connections, be sure to match the DIGITAL INs to
the corresponding input source respectively.(For details, refer to "When
selecting the DIGITAL IN SETUP" on page 37.)
SPEAKER INDICATOR
INPUT SIGNAL
INDICATORS
SLEEP INDICATOR
MUTE INDICATOR
AUTO INDICATOR
INPUT, FREQUENCY, VOLUME LEVEL, OPERATING INFORMATIONs, etc.
• This OPTICAL IN should be connected to the component capable of
DTS, Dolby Digital or PCM format digital signals, etc.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Universal Remote Controls
ꢀNote: For enhanced Universal Remote Programming instructions and manufacturer’s codes, please refer to the operating
manual inclosed with this Universal Remote Control.
This remote control has 3 operating modes as follows:
• OSD (On-Screen Display) mode: Allows you to look at information about basic operation of this unit on your monitor TV
and to operate this unit by moving an arrow that appears on the screen of your monitor TV.
• Sherwood mode: Allows you to operate this unit and other Sherwood components like cassette decks, CD players, etc.(To
operate other Sherwood components, you should make the DIGI LINK connections between them.)
• Non-Sherwood mode: Allows you to operate other non-Sherwood audio and video components that are remote compatible.
ꢀNotes:
• The setup code for each component must be entered before operation.
• For setup codes(manufacturer’s codes), please refer to “Set-Up Code Tables” in the operating manual of this remote
control.
• Some operation buttons have different functions according to each operation mode.
• Be sure to set the remote control to the correct mode before operation.
DIGI LINK SYSTEM REMOTE CONTROLS
• This section explains the basic functions for Sherwood or OSD mode. For the non-Sherwood mode, refer to the
operating manual of this remote control.
• All Sherwood components bearing the DIGI LINK (II or III) logo can be used with this remote control.
• For system remote control operation, first make the DIGI LINK connections between Sherwood components.
• The numbered buttons on the remote control have different functions in different modes. For details, refer to the
“FUNCTION TABLE of the NUMBERED BUTTONS” on the following page.
• In the DIGI LINK III remote control system, if pressing PLAY, etc. on CD player or tape deck, CD or TAPE
MONITOR is selected automatically on the receiver without selecting the input source. Then PLAY, etc. starts.
LED LAMP
DEVICE BUTTONS
To operate the desired component with this remote
DVD
control, first select the corresponding DEVICE button.
VOLUME UP/DOWN(
/
) BUTTONS
POWER BUTTON
ENTER BUTTON
VOL. CH LEVEL
CHANNEL LEVEL UP/DOWN(
/
) BUTTONS
OSD
CH SEL
CURSOR CONTROL(
,
,
,
) BUTTONS
ENTER
RPT
INTRO
B
A
TITLE
RETURN
7.1 SURR
AUTO
NUMERIC(1~0) BUTTONS
• For selecting preset stations in tuner mode.
DSP
MODE
• For selecting a track or a disc in CD mode, etc.
• When selecting a disc, select disc No. (1~5) within 2 sec.
after pressing DISC(marked "P.SCAN") button.
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
LIGHT BUTTON
HOME THEATER MASTER
RNC-220
Activates the backlighting of the remote control
for 7 sec. If any other button is pressed while
the backlighting is on, the remote control will
remain backlit for an additional 7 sec.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀFUNCTION TABLE of the NUMBERED BUTTONS.
Component
buttons to be
controlled
(for DVD player)
(for receiver,
"001")
VD-4106, etc.
("057")
(for CD player,
"001")
(for tape deck,
"001")
V-756, etc.
("001")
VD-4103, etc.
("112")
VD-2103, etc.
("114")
Button
symbol
("074")
POWER
ZOOM
POWER
MUTE
POWER
POWER
POWER
MUTE
<POWER>
<MUTE>
<POWER>
<MUTE>
MUTE
FORWARD SLOW
SELECT/ENTER
FORWARD SKIP
REVERSE SKIP
TITLE
OPEN/CLOSE
SEARCH
OPEN/CLOSE
PAL/NTSC
OPEN/CLOSE
KEY UP
RANDOM
CH LEVEL UP(
)
<CH LEVEL UP( )>
<CH LEVEL DOWN( )>
<ON-SCREEN DISPLAY>
<CHANNEL SELECTOR>
DECK SELECTOR A
DECK SELECTOR B
<CH LEVEL UP( )>
<CH LEVEL DOWN( )>
<ON-SCREEN DISPLAY>
<CHANNEL SELECTOR>
REPEAT A< >B
INTRO SCAN
(SUBTITLE ON/OFF)
MENU
KEY DOWN
MENU
CH LEVEL DOWN(
)
MENU
SETUP
DISPLAY
MENU
ON-SCREEN DISPLAY
CHANNEL SELECTOR
7.1 CH SURROUND
RETURN
SETUP
SETUP
MENU
TITLE
TITLE
TITLE
CLEAR
RETURN
RETURN
RETURN
RETURN
RETURN
OPEN/CLOSE
(DISC)
+10
+10
PRESET SCAN
AUTO/MANUAL
DSP MODE
DISC
AUDIO
CHANNEL
NTSC/PAL
SUBTITLE
AUDIO
PROGRAM
RESUME
DISPLAY
SUBTITLE
<AUTO/MANUAL>
<DSP MODE>
<STEREO>
<AUTO/MANUAL>
<DSP MODE>
SUBTITLE
ANGLE
SUBTITLE
ANGLE
REPEAT
SETUP
STEREO
<STEREO>
PROGRAM
CLEAR
PROGRAM
V-MODE
PROGRAM
L/R/ST
TEST
SELECT/ENTER
CURSOR UP
CURSOR DOWN
TITLE
SETUP
AUDIO
TEST TONE
<TEST TONE>
REVERSE PLAY
FORWARD PLAY
PAUSE
<TEST TONE>
TIME
A-TIME
SLOW
I
TUNER
CD
N
P
U
T
PLAY
STEP
STEP
ANGLE
PLAY
PAUSE
PAUSE
PAUSE
PAUSE
CLEAR
TAPE MONITOR
AUX
STOP
STOP
STOP
CURSOR LEFT
REPEAT
RANDOM
PROGRAM
STOP
STOP
S
E
L
E
C
T
REVERSE SEARCH
FORWARD SEARCH
REVERSE SKIP
FORWARD SKIP
REPEAT
REVERSE SEARCH
FORWARD SEARCH
REVERSE SKIP
FORWARD SKIP
REPEAT
REVERSE SEARCH
FORWARD SEARCH
REVERSE SKIP
FORWARD SKIP
REPEAT
REWIND
REVERSE SKIP
FORWARD SKIP
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 4
ANGEL
AUDIO
FAST FORWARD
O
R
CURSOR RIGHT
REPEAT A<>B
RECORD
REPEAT A<>B
DISPLAY
REPEAT A<>B
ON-SCREEN DISPLAY
MARKER
REPEAT A<>B
DISPLAY
SYSTEM DISPALY
SLEEP
<SYSTEM DISPALY>
<SLEEP>
<SYSTEM DISPALY>
<SLEEP>
MARKER
SEARCH
SUBTITLE
RANDOM
MEMORY
PBC
ROOM 2
<ROOM 2>
<ROOM 2>
INTRO SCAN
CURSOR UP
CURSOR DOWN
CURSOR RIGHT
CURSOR LEFT
ENTER
INTRO SCAN
CURSOR UP
CURSOR DOWN
CURSOR RIGHT
CURSOR LEFT
ENTER/PLAY
VOLUME UP
VOLUME DOWN
0/10~9
RESUME
REPEAT A<>B
7.1 CH DIRECT
<7.1 CH DIRECT>
<CURSOR UP( )>
<CURSOR DOWN( )>
<CURSOR RIGHT( )>
<CURSOR LEFT( )>
<ENTER>
<7.1 CH DIRECT>
<CURSOR UP( )>
<CURSOR DOWN( )>
<CURSOR RIGHT( )>
<CURSOR LEFT( )>
<ENTER>
CURSOR UP
CURSOR DOWN
CURSOR RIGHT
CURSOR LEFT
ENTER/PLAY
VOLUME UP
VOLUME DOWN
0/10~9
PAUSE
STOP
CURSOR UP(
)
CURSOR DOWN(
CURSOR RIGHT(
CURSOR LEFT(
ENTER
)
)
FORWARD SCAN
REVERSE SCAN
PLAY
)
VOLUME UP(
VOLUME DOWN(
0~9
)
<VOLUME UP( )>
<VOLUME DOWN( )>
<VOLUME UP( )>
<VOLUME DOWN( )>
)
0~9
0~9
0~9
ꢀNotes:
• Some functions for CD player, tape deck, etc. may not be available.
• For details about functions, refer to the operating instructions of each component.
• The functions in < > work for this receiver, not for the CD player or tape deck.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING COMPONENTS WITH REMOTE CONTROL
REMOTE CONTROL OPERATION RANGE
Enter the setup code of the components
respectively, referring to “ENTERING A
SETUP CODE”(page14).
• Use the remote control within a range of about 7
meters (23 feet) and angles of up to 30 degrees
aiming at the remote sensor.
1
Turn on the components you want to
operate.
W
R
A
S
S
W
I
D
E
R
A
N
G
E
A
M
P
L
I
F
I
E
R
TAGE
AUDIO/VIDEO SURROUND RECEIVER R-863
2
MULTI CONTROL
MASTER VOLUME
SOURCE
DIRECT
BAND
T/P MODE
CINEMA EQ
MULTI ROOM
REMOTE SENSOR
LOCK
TUNING/PRESET
DYNAMIC
RANGE
ROOM2 FEED
POWER
INPUT SELECTOR
SURROUND MODE
EXTRA SURR.
AUDIO
VIDEO TAPE MON. 7.1CH DIRECT DECODING
STEREO DIGITAL/ANALOG
STANDBY
ON/STANDBY
6.1/7.1
ON
/
OFF
Press the DEVICE button on the remote
control corresponding to the component
PHONES
CHANNEL
SELECTOR
SPEAKER
ON/OFF
TEST TONE
TONE MODE VIDEO LABEL MEMO/ENTER
OPTICAL IN S-VIDEO
VIDEO
L
-
AUDIO
-
R
3
you want to operate.
7m
Press the button corresponding to the
operation you want while aiming the
remote control at the REMOTE SENSOR
4
on the component.
DVD
VOL. CH LEVEL
• When a button is pressed, the corresponding DEVICE
button flickers.
OSD
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
• When operating a Sherwood CD player or tape deck
using the system remote control, aim the remote
control at the REMOTE SENSOR on this unit.
• However, in case of Sherwood DVD player, aim it
at the REMOTE SENSOR on the corresponding
component.
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
LOADING BATTERIES
ꢁWhen this remote control does not operate the component, the old batteries should be replaced.
ꢁIf the batteries are removed for a longer period of time, the remote control might lose its memory and require
reprogramming
Remove the cover.
Load four batteries(“AAA” size, 1.5 V)
matching the polarity.
1
2
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION ON REMOTE COMMAND CODES
• This receiver recognizes and responds to IR codes that are not transmitted by the supplied remote control unit.
These commands and their corresponding functions, shown on the following table, are made available for
custom installers and advanced hobbysts who are already familiar with the programming of such devices as the
Crestron Touch Screen and the Philps Pronto.
Custom Code : 8345H(NEC)
FUNCTIONS
DTS
CODES
70H
FUNCTIONS
DSP MODE
VIDEO 1
CODES
5CH
56H
Dolby Digital
71H
EXTRA SURROUND 6.1/7.1
DECODING MODE
STEREO
44H
VIDEO 2
5AH
07H
58H
VIDEO 3
4FH
VIDEO 4
5BH
03H
DIGITAL/ANALOG
Dolby Pro Logic II Movie
Dolby Pro Logic II Music
DTS Neo Movie
DTS Neo Music
MPEG
E1H
E8H
E9H
EDH
EEH
EBH
EFH
TUNER
TAPE MONITOR
AUX
06H
0AH
0BH
4AH
7BH
CD
7.1 CH DIRECT
SOURCE DIRECT
PCM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ENTERING A SETUP CODE
• This remote control can control up to eight different components.
• Before operating audio and video components using the remote control supplied with this receiver, the setup code for each
component should be entered.
• Because only the setup codes for CD player and DVD player among Sherwood components are listed in the operating manual of this
remote control, when entering a setup code for Sherwood components for system remote control operation, find the corresponding setup
code in the “FUNCTION TABLE of the NUMBERED BUTTONS” on page 11 in this operating instructions. For your reference, the setup
cord for each Sherwood component such as CD player, tape deck and DVD player(V-756, etc.) is “001” respectively.(However, the setup
code for some Sherwood DVD player such as VD-4103, etc. is “057”, “074”, “112”, “114”.) Enter each setup code for CD player and tape
deck doing steps ③, ④and ⑤as follows.
Find the setup code for your component
referring to “Set-Up Code Table” in the
operating manual of this remote control.
Turn on the component you want to control.
2
1
Example) When entering the setup code for this
receiver, turn on this receiver.
Example) The correct setup code for this receiver is
“001”.
Press the corresponding DEVICE and the
Enter the 3 digit setup code aiming the remote control
MUTE buttons simultaneously.
at the REMOTE SENSOR on the component.
3
4
DVD
0
0
1
For "001" :
For "102" :
VOL. CH LEVEL
For receiver or amplifier :
OSD
CH SEL
DVD
ENTER
RPT
INTRO
B
VOL. CH LEVEL
A
TITLE
For CD player
:
7.1 SURR
RETURN
OSD
CH SEL
AUTO
DSP
MODE
ENTER
ST
RPT
INTRO
A
B
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TITLE
7.1 SURR
RETURN
AUTO
1
0
2
TUNER
CD
T1/MON
AUX
VID4
PHONO
DSP
MODE
VID1
VID2
VID3
VID5
ST
SYS DISP
SLEEP
DIRECT IN
ROOM2
DISC
TEST
TONE
CENTER
MODE
P.SCAN
HOME THEATER MASTER
RNC-220
For CABLE
:
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁYour component will be turned off when the correct
setup code is entered.
ꢁContinue to enter the corresponding codes until your
component turns off.
ꢁThen the LED lamp and the corresponding DEVICE
button on the remote control light up for 20 seconds.
ꢁIf the LED lamp and the corresponding DEVICE
button go off, start from the step
③
again.
Press the corresponding DEVICE button to
store the setup code.
Operate the component using the
corresponding function buttons on the remote
control such as POWER, CH ∧/∨ and
VOL ∧/∨buttons, etc.
5
6
For receiver or amplifier :
ꢁIf any of the buttons do not perform as they should
start from step ①again to enter the next setup code.
■Note:
DVD
VOL. CH LEVEL
For CD player
:
OSD
CH SEL
ENTER
RPT
INTRO
A
B
ꢁSome audio and video components have separate
buttons for POWER ON/OFF.
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
For CABLE
:
TUNER
CD
T1/MON
AUX
VID4
PHONO
In this case, press the corresponding DEVICE button
to turn the component ON and press the POWER
button to turn the component OFF.
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁIf there is no correct setup code or if the
Manufacturer/Brand for your component is not listed
in “Set-Up Code Table” in the operating manual of
this remote control, please use the “Auto Search
Method” on page 10 in the operating manual of this
remote control.
ꢁAlthough each setup code is designed to work with
many different modes, certain codes may not work with
some models. (Also, certain codes may only operate
some of the functions available on a given model.)
ꢁThen the LED lamp and the corresponding DEVICE
button will flicker twice.
Repeat the above steps ①to ⑥for each
of your other components.
7
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
ꢀNotes :
ꢁBefore operating this receiver with the supplied remote control, refer to “Universal Remote Controls” on page 10 for details about operation.
ꢁBefore operating this receiver, first set this unit as desired for optimum performance, by using the OSD menu setting procedures. (For
details, refer to “OSD Menu Settings” on page 32.)
LISTENING TO A PROGRAM SOURCE
Select the desired input source.
Before operation
DVD
POWER
ON / OFF
3
ꢁEnter the standby mode.
V
O
L
.
C
H
L
E
V
E
L
INPUT SELECTOR
VIDEO
OSD
C
H
S
E
L
AUDIO
TAPE MON.
ENTER
RPT
INTRO
B
A
TITLE
7.1 SURR
RETURN
AUTO
DSP
TUNER
VID1
CD
MODE
T1/MON
VID3
AUX
VID4
ST
DISC
TEST
TONE
CENTER
MODE
P
.SCAN
or
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID2
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁThe STANDBY button lights up in red.
ꢁEach time the “AUDIO” button is pressed, the input
source changes as follows:
This means that the receiver is not disconnected
from the AC mains and a small amount of current
is retained to support the memorized contents and
operation readiness.
ꢂ
TUNER ꢂ CD ꢂ AUX
(frequency display)
ꢁTo switch the power off, push the POWER switch
again.
ꢁEach time the “VIDEO” button is pressed, the input
source changes as follows:
ꢁThen power is cut off and the STANDBY button
goes off.
ꢂVIDEO 1 ꢂVIDEO 2 ꢂVIDEO 3 ꢂVIDEO 4
ꢁWhen the TAPE MONITOR button is set to on so that
“TAPE MON” lights up, other inputs can not be heard
from the speakers.
In the standby mode, turn the power on.
To listen to an input source except TAPE MONITOR, be
sure to set the TAPE MONITOR button to off.
1
DVD
STANDBY
V
O
L
.
C
H
L
E
V
E
L
OSD
C
H
S
E
L
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to the
receiver’s TAPE MONITOR jacks.
ON/STANDBY
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
or
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
Only when you listen to the component connected to these
jacks, set the TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can listen to the sound
being recorded during recording, and not the source sound.
For further details, refer to the operating instructions of the
connected component.
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁEach time the STANDBY button on the front panel or
the POWER button on the remote control is pressed,
the receiver is turned on to enter the operating
mode(the STANDBY button lights up in blue) or off
to enter the standby mode (the STANDBY button
lights up in red).
ꢀWhen selecting the 7.1 CH DIRECT as desired
DVD
7.1CH DIRECT
V
O
L
.
C
H
L
E
V
E
L
OSD
C
H
S
E
L
ꢁIn the standby mode, if one of the INPUT
SELECTOR buttons is pressed, the receiver is turned
ENTER
RPT
INTRO
A
B
or
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
TEST
TO
CENTER
P.SCAN
on automatically and the desired input is selected.
TUNER
CD
T1/MON
AUX
VID4
PHONO
DIRECT IN
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁ
Depending on the surround back speaker setting, “7.1(,6.1 or
5.1) CH DIRECT” is displayed and the 8(/7/6) separate analog
signals from the component connected to this input pass
through the tone, volume and bass management(if selected)
circuits only and can be heard from your speakers.(In case
that the TAPE MONITOR button is set to on, the TAPE
MONITOR button is automatically set to off.)
SPEAKER
Switch the speakers on.
ON/OFF
2
ꢁThen the SPEAKER indicator lights up on the display
and sound can be heard from the speakers connected
to the speaker terminals.
ꢁWhen using headphones for private listening, press the
SPEAKER button again to switch the speakers off.
ꢁPress the 7.1 CH DIRECT button or select the desired input
source to cancel the 7.1 CH direct function.
ꢁThese analog signals can be heard only. They cannot be
recorded.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
When CD, TAPE MON or VIDEO 1~
VIDEO 4 is selected
Adjusting the tone (bass and treble)
Select the tone mode as desired.
Select the digital or the analog input as
7
desired.
4
DIGITAL/ANALOG
TONE MODE
ꢁEach time this button is pressed, the tone mode
ꢁEach time this button is pressed, the corresponding
changes as follows:
input is selected as follows:
ꢂBASS ꢂTREBLE ꢂDEFEAT OFF(or ON)
ꢂDIGITAL ꢂANALOG
ꢁThe tone display is shown for 5 seconds.
ꢁIf the tone display disappears, press the TONE
MODE button again.
ꢁ( ) : When the tone defeat function is activated
(“DEFEAT ON”), bass and treble modes cannot be
ꢁTo listen to DTS, Dolby Digital or MPEG program
sources in the 2-CH downmix mode, in the stereo
mode, the digital input must be selected. (For
details, refer to “Downmixing into 2 front
channels” on page 24.)
ꢁWhen TUNER or AUX is selected as an input
source, the analog input is automatically selected.
■Notes:
selected
■Note:
ꢁWhen the source direct function is activated, the
tone mode cannot be selected.
ꢁWhen the selected digital input is not connected.
“DIGITAL” flickers, meaning no sound. (Refer to
“ENJOYING SURROUND SOUND” on page 21.)
At the desired tone mode, adjust as
desired.
ꢁTo select the digital input, you must match the
connected DIGITAL IN to the corresponding input
source.
(For details, refer to “When selecting the DIGITAL
IN SETUP” on page 37.)
8
MULTI CONTROL
Operate the selected component for
playback.
5
■At the tone defeat mode, each time the MULTI
CONTROL knob is rotated, the tone defeat mode
changes as follows:
ꢁWhen playing back the program sources with
surround sound, refer to “ENJOYING SURROUND
SOUND” on page 21.
DEFEAT ON : When listening to a program source
↕
without the tone effect.
DEFEAT OFF : When adjusting the tone for your
taste.
Adjust the (overall) volume.
■At the desired tone (bass or treble), each time the
MULTI CONTROL knob is rotated, the tone level
can be adjusted within the range of +10~ -10 dB.
ꢁIn general, we recommend the bass and treble to be
adjusted to 0(flat) level.
6
MASTER VOLUME
DVD
VOL. CH LEVEL
OSD
CH SEL
VOL.
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
or
ꢁTo complete tone adjustment, repeat the above steps
⑦and ⑧.
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P
.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
ꢁExtreme settings at high volume may damage your
speakers.
DOWN
UP
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To achieve pure sound quality.
To compensate for edgy or shrill movie
sound tracks.
9
10
SOURCE
DIRECT
CINEMA EQ
ꢁOnly when playing program sources recorded in
analog stereo or digital 2 ch PCM format, the source
direct function can be selected.
ꢁWhen 96 kHz PCM(2 channel stereo) signals are
input or the source direct function is selected, the
cinema EQ function can not be selected.
ꢁ“DIRECT” lights up and stereo mode is
automatically selected. Then the sound that bypasses
the tone circuitry will be heard.
ꢁ“CINEMA-EQ ON” will scroll on the display.
ꢁPress the button again to cancel, then “CINEMA-
EQ OFF” will scroll on the display.
ꢁPress the button again to cancel the source direct
function.
ꢁWhen you select the 7.1 CH DIRECT as input
source or the digital signals from DTS, Dolby
Digital or MPEG sources, etc. are input, the source
direct function is automatically canceled.
To mute the sound.
To listen with the headphones.
11
12
PHONES
DVD
VOL. CH LEVEL
OSD
CH SEL
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
ꢁEnsure that the SPEAKER button is set to off.
ꢁWhen listening to DTS, Dolby Digital or MPEG
program sources, if the headphones are plugged in
and the SPEAKER button is set to off, the 2-CH
downmix mode will be selected automatically. (For
details, refer to “Downmixing into 2 front
channels” on page 24.)
HOME THEATER MASTER
RNC-220
ꢁ“MUTE” lights up.
ꢁTo resume the previous sound level, press the
button again.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SURROUND SOUND
ꢁThis unit incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound
atmosphere in your personal Home Theater.
Surround modes
ꢁDTS Neo : 6 Music
■DTS Digital Surround
This mode is suited mainly for playing music. The front left and front right
signals bypass the decoder and are played directly so there is no loss of
sound quality, and the effect of the surround signals from the center,
surround left, surround right and surround back channels adds a natural
sense of expansion to the sound field.
DTS Digital Surround(also called simply DTS) is a multi-channel digital signal
format which can handle higher data rates than Dolby Digital. Although both
Dolby Digital and DTS are 5.1 channel formats, discs bearing the “
are generally thought to provide better sound quality due to the
lower audio compression required.
”
It also provides wide dynamic range and separation, resulting in magnificent
sound.
“DTS”, “DTS-ES Extended Surround” and “Neo : 6” are trademarks of
Digital Theater Systems,Inc.
(
)
■DTS - ES Extended Surround™
This is a new multi channel digital signal format which greatly improves
the 360- degree surround impression and space expression thanks to
further expanded surround signals, offering high compatibility with the
conventional DTS format.
■Dolby Digital
Dolby Digital is the multi- channel digital signal format developed by
Dolby Laboratories. Discs bearing the “
” includes the
DOLBY
D I G I T A L
recording of up to 5.1 channels of digital signals, which can reproduce
much better sound quality, spatial expansion and dynamic range
characteristics than the previous Dolby Surround effect.
In addition to the 5.1 channels, DTS-ES Extended Surround also offers the
surround back (sometimes also referred to as “surround center”) channel
for surround playback with a total of 6.1 channels. DTS-ES Extended
Surround includes two signal formats with different surround signal
recording methods as follows:
■Dolby Pro Logic
Dolby Pro Logic is a specially encoded two channel surround format
which consists of four channels ( front left, center, front right and
surround). Sources bearing the “
theater - like surround sound.
The surround channel is monaural, but is played through both surround speakers.
ꢁDTS-ES™ Discrete 6.1
Because the signals for 6.1 channels (including the surround back channel)
are fully independent, it is possible to achieve a sense that the acoustic
image are moving about freely among the background sounds surrounding
the listener from 360 degrees.
” provide the
DOLBY SURROUND
Though maximum performance is achieved when sound tracks recorded
with this system are played using a DTS -ES decoder, when played with a
conventional DTS decoder, the surround back channel signals are
automatically downmixed to the surround left and surround right channels
so that none of the signal components are lost.
■Dolby Pro Logic II surround
This mode applies conventional 2- channel signals such as digital PCM or
analog stereo signals as well as Dolby Surround signals, etc. to surround
processing to offer improvements over conventional Dolby Pro Logic
circuits. Dolby Pro Logic II surround includes two modes as follows:
ꢁDTS - ES™ Matrix 6.1
With this format, the additional surround back channel signals undergo
matrix encoding and are input to the surround left and surround right
channels beforehand. During playback, they are decoded to the surround
left, surround right and surround back channels. Because the bit stream
format is 100% compatible with conventional DTS signals, the effect of the
DTS-ES Matrix 6.1 format can be achieved even with DTS 5.1- channel
signal sources. Of course, it is possible to play DTS-ES Matrix 6.1 -
channel signal sources with a DTS 5.1 - channel decoder.
When DTS-ES Discrete 6.1 or Matrix 6.1 sources are decoded with a DTS -
ES decoder, the format is automatically detected upon decoding and the
optimum surround mode is selected.
ꢁDolby Pro Logic II MOVIE
When enjoying movies, this mode allows you to further enhance the
cinematic quality by adding processing that emphasizes the sounds of the
action special effects.
ꢁDolby Pro Logic II MUSIC
When listening to music, this mode allows you to further enhance the
sound quality by adding processing that emphasizes the musical effects.
■Dolby Virtual
This mode employs sophisticated digital processing to create the illusion of
“phantom” speakers, this mode allows you to experience surround sound
effects from Dolby Digital, Dolby Surround or 2-channel (recorded in digital
PCM or analog stereo) sources, through just a single pair of front speakers.
However, some DTS - ES Matrix 6.1 sources may be detected as DTS
sources. In this case, the DTS - ES Matrix mode must be selected manually
to play these sources.
ꢁIn DTS-ES Discrete 6.1, DTS -ES Matrix 6.1 sources, the surround back
channel is monaural, but can be played through a single(in 6.1 mode) or
two surround back speakers(in 7.1 mode) depending on the surround
back speaker setting.(For details, refer to “SETTING THE SPEAKER
SETUP” on page 34.)
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double - D symbol are trademarks of Dolby
Laboratories.
■MPEG Multichannel
This mode is a surround system which faithfully reproduces the ambience and
dynamics of movie soundtracks and music alike. Though the number of audio
ꢀDTS Neo : 6™ surround
This mode applies conventional 2-channel signals such as digital PCM or
analog stereo signals to the high precision digital matrix decoder used for
DTS-ES Matrix 6.1 to achieve 6.1-channel surround playback. DTS Neo : 6
surround includes two modes for selecting the optimum decoding for the
signal source.
channels are same as Dolby Digital, discs bearing the “
provides much better at locating individual sounds to the correct and stable
position in the sound stage.
”
■Extra Surround 6.1/7.1
ꢁDTS Neo : 6 Movie
This mode extracts the surround back (sometimes also referred to as “surround
center”) signals from the surround left and surround right signals and
reproduces it as well as the original multichannel signals during playback of
multi-channel program sources recorded in DTS, Dolby Digital, etc.
This mode is optimum for playing movies. Decoding is performed with
emphasis on separation performance to achieve the same atmosphere with
2-channel sources as with 6.1-channel sources.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁThe following modes apply conventional 2-channel signals such as digital PCM or analog stereo signals to high performance
Digital Signal Processor to recreate sound fields artificially. Select one of the twelve provided surround modes according to
the program source you want to play.
■Theater
■Arena 1/2
This mode provides the effect of being in a theater -in-the
round when watching a play.
This mode provides the feeling of a live concert in a medium
- sized (Arena 1) or large (Arena 2) arena.
■Movie
■Club 1/2
This mode provides the effect of being in a movie theater
when watching a movie.
This mode creates the sound field of a jazz club with a low
ceiling and hard walls (Club 1) or a live house with a
relatively spacious floor (Club 2).
■Hall 1/2
This mode provides the ambience of a chamber hall for
chamber music or an instrumental solo (Hall 1) or a concert
hall for orchestral music or an opera (Hall 2).
■Game
Use this mode to enjoy video game sources.
■Matrix
This mode reproduces a delayed signals from the surround
channels to emphasize the sense of expansion for music
sources.
■Stadium
This mode provides the expansive sound field to achieve the
true stadium effect when watching baseball or soccer games.
■Church
This mode provides the ambience of a church for baroque,
string orchestral or choral group music.
ꢁWhen using the 7.1 CH DIRECT INPUTs to play back the sound from an additional multichannel decoder for surround sound,
yon can enjoy the corresponding surround sound ,too.( For details, refer to the operating instructions of the component to be
connected.)
For your reference, the sound from each channel can be reproduced according to the surround modes as follows:
Channels
(FRONT)
CENTER
SURROUND
L/R
SURROUND BACK
CENTER, L/R
FRONT L/R
SUBWOOFER
Modes
DTS
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
—
ꢃ
ꢃ
ꢃ
ꢃ
—
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
—
ꢃ
ꢃ
ꢃ
ꢃ
—
ꢃ
—
◎
◎
—
—
—
—
—
◎
◎
—
—
◎
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
DTS ES DISCRETE/MATRIX
DTS NEO MOVIE/MUSIC
DOLBY DIGITAL
DOLBY PRO LOGIC
DOLBY PRO LOGIC II MOVIE/MUSIC
DOLBY VIRTUAL
MPEG
EXTRA SURROUND
MATRIX
Other Surround
STEREO
7.1 CH DIRECT
◎: Depending on the surround back speaker setting, the sound from the SURROUND BACK CENTER or L/R channels can be reproduced.
ꢁDepending on the speaker settings and the number of the encoded channels, the sound from the corresponding channels
cannot be reproduced.(For details, refer to “SETTING THE SPEAKER SETUP” on page 34.)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker placement
Ideal speaker placement varies depending on the size of your room and
the wall coverings, etc. The typical example of speaker placement and
recommendations are as follows :
1
4
3
■Front left and right speakers and center speaker
ꢁPlace the front speakers with their front surfaces as flush with TV or
monitor screen as possible.
ꢁPlace the center speaker between the front left and right speakers
and no further from the listening position than the front speakers.
ꢁPlace each speaker so that sound is aimed at the location of the
listener’s ears when at the main listening position.
6
7
11
10
■Surround left and right speakers
ꢁPlace the surround speakers approximately 1 meter (40 inches) above
the ear level of a seated listener on the direct left and right of them or
slightly behind.
8
9
■Surround back left and right speakers.
ꢁPlace the surround back speakers at the back facing the front at a
narrower distance than the front speakers.
ꢁWhen using a single surround back speaker, place it at the rear center
facing the front at a slightly higher position (0 to 10 inches) than the
surround speakers.
ꢁWe recommend installing the surround back speaker(s) at a slightly
downward facing angle. This effectively prevents the surround back
channel signals from reflecting off the TV or screen at the front center,
resulting in interference and making the sense of movement from the
front to the back less sharp.
1. TV or screen
7. Surround right speaker
8. Surround back left speaker
9. Surround back right speaker
10. Surround back center speaker
11. Listeing position
2. Front left speaker
3. Subwoofer
4. Center speaker
5. Front right speaker
6. Surround left speaker
Surround speaker
Front speaker
Surround back
speaker
Point slightly
downward
■Subwoofer
ꢁThe subwoofer reproduces powerful deep bass sounds.
Place a powered subwoofer anywhere in the front as desired.
60 to 90 cm
■Notes :
ꢁWhen using a conventional TV , to avoid interference with the TV
picture, use only magnetically shielded front left and right and center
speakers.
ꢁTo obtain the best surround effects, the speakers except the subwoofer
should be full range speakers.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ENJOYING SURROUND SOUND
ꢁSurround sound effect will not work properly if the signal passes through a graphic equalizer.
Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer.
■Note : Before surround playback, first perform the SPEAKER SETUP procedure, etc. on the OSD menu for optimum
performance.(For detail, refer to “SETTING THE SPEAKER SETUP” on page 34.)
Depending on the input digital signal format, select the desired decoding mode.
ꢁEach time this button is pressed, the decoding mode changes as
follows :
* Auto mode(“ AUTO” lights up) : The input digital signal format (DTS,
Dolby Digital, MPEG or PCM ( 2 channel stereo), etc.) used by the
1
DVD
DECODING
selected digital input source is detected automatically to perform the
V
O
L
.
C
H
L
E
V
E
L
OSD
C
H
S
E
L
necessary decoding process for optimum surround modes.
* Dolby Digital mode(“DOLBY DIGITAL” lights up) : The Dolby Digital
signals processing is performed only when Dolby Digital signals are input.
* DTS mode(“ DTS” lights up) : The DTS signal processing is performed
only when DTS signals are input.
ENTER
or
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
AUTO
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
* MPEG mode(“MPEG” lights up) : The MPEG signal processing is
performed only when MPEG signals are input.
* PCM mode(“PCM” lights up) : The PCM signal processing is performed
only when PCM signals are input.
■Notes :
ꢁOnly when the digital input is selected as signal input for the input sources except TUNER and AUX, the
decoding mode can be selected.
ꢁNoise may be generated at the beginning of playback and while searching during DTS playback in the auto mode.
To minimize this possibility, try playing in the DTS mode.
Select the desired surround mode.
DVD
V
O
L
.
C
H
L
E
V
E
L
OSD
C
H
S
E
L
2
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
or
DSP
DSP
MODE
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
ꢁEach time the MULTI CONTROL knob on the front is rotated or the DSP
MODE button on the remote control is pressed, the surround mode changes
depending on the input signal format and the selected decoding mode as follows:
* When Dolby Digital signals are input in the auto or Dolby Digital mode,
the following modes can be selected.
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-225
→DOLBY DIGITAL (↔DOLBY PRO LOGIC II MOVIE ↔DOLBY PRO LOGIC II MUSIC ↔DOLBY PRO LOGIC)↔DOLBY VIRTUAL ←
Only when Dolby Digital 2.0 channel signals are input, the surround modes in ( ) can be selected, too.
* When PCM (2 channel stereo) signals are input in the auto or PCM mode, the following modes can be selected.
→DOLBY PRO LOGIC II MOVIE ↔DOLBY PRO LOGIC II MUSIC ↔DOLBY PRO LOGIC ↔DOLBY VIRTUAL ↔DTS NEO MOVIE ↔DTS NEO MUSIC ←
→MATRIX ↔GAME ↔ARENA 2 ↔ARENA 1 ↔CLUB 2 ↔CLUB 1 ↔CHURCH ↔STADIUM ↔HALL 2 ↔HALL 1↔MOVIE ↔THEATER ←
ꢁWhen the analog input is selected as signal input and analog stereo signals are input, you can select the same
surround modes as those listed for the PCM input.
ꢁHowever, when DTS or MPEG signals are input in the following decoding modes, the corresponding surround mode will
be automatically selected regardless of using the MULTI CONTROL knob or DSP MODE button:
* When DTS signals are input in the auto or DTS mode, the corresponding DTS mode will be selected.
* When MPEG signals are input in the auto or MPEG mode, MPEG mode will be selected.
■Notes:
ꢁWhen the selected decoding mode is not matched to the input signal format, the indicator of the signal being input
flickers, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the
required decoding mode and the available surround mode according to the input signal format.
ꢁWhen the 7.1 CH DIRECT is selected as an input source, the surround mode cannot be selected.
ꢁWhen the source direct function is activated, the decoding mode and surround mode cannot be selected.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Continued
ꢀWhen playing some multi-channel program sources in the Extra Surround 6.1/7.1 mode.
RPT
A
DVD
EXTRA SURR.
6.1/7.1
VOL. CH LEVEL
TITLE
7.1 SURR
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
or
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁWhen the digital signals from the following program sources only are input in the available decoding mode, if
these buttons are pressed, the corresponding surround mode will be selected.
ꢄDolby Digital 5.1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX
technology) : EXTRA SURROUND mode,
ꢄDTS 5.1-channel sources : DTS ES MATRIX mode.
ꢁPress the EXTRA SURROUND 6.1/7.1 button on the front panel or the 7.1 CH SURROUND button on the
remote control again to cancel the 6.1(or 7.1) surround mode.
ꢁAccording to whether the surround back speaker is set to “1CH” or “2CH”, the 6.1 or 7.1 mode is selected.
ꢁHowever, when the surround back speaker is set to “None”, the Extra Surround 6.1/7.1 mode cannot be activated.
ꢀWhen canceling the surround mode for normal stereo operation.
DVD
STEREO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
or
MODE
ST
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁThen the stereo mode is selected.
ꢁTo cancel the stereo mode, select the desired surround mode with using the MULTI CONTROL knob or the DSP
MODE button, etc.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the level of the selected channel
as desired.
Adjusting each channel level
ꢁIf you have performed the CH LEVEL TRIM
procedure on the OSD menu, you can skip this
procedure. (For details, refer to “SETTING THE
CH LEVEL TRIM” on page 43.)
4
MULTI CONTROL
DVD
VOL. CH LEVEL
OSD
CH SEL
CH LEVEL
Select the desired channel.
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
or
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
3
P.SCAN
DVD
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
DOWN
VOL. CH LEVEL
UP
CHANNEL
SELECTOR
CH SEL
HOME THEATER MASTER
RNC-220
OSD
CH SEL
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
or
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
ꢁIf the channel display disappears, start from the
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
above step ③again.
ꢁEach time this button is pressed, the corresponding
channel is selected and displayed for 3 seconds as
follows:
Repeat the above steps ③and ④to
adjust each channel level until the sound
level of each speaker is heard to be
equally loud.
ꢂFRONT-L ꢂCENTER(or FRONT-C) ꢂFRONT-R ꢂSURR-R
SUBWOOFER ꢅSURR-L ((ꢅSURR-C) or (ꢅBACK-L ꢅBACK-R)) ꢅ
5
ꢁDepending on the speaker setting, items set to None
or No can not be selected.
At each channel, adjust the level as
desired until the sound level of each
speaker is heard to be equally loud.
Adjusting each channel level with test
tone
7
ꢁOnly when playing a program source in available
surround modes except the DOLBY VIRTUAL
mode, the volume level of each channel can be
adjusted easily with the test tone function.
■Note : When the 7.1 CH DIRECT is selected as an
input source, the test tone function does not
work.
MULTI CONTROL
DVD
VOL. CH LEVEL
OSD
CH SEL
CH LEVEL
ENTER
RPT
INTRO
A
B
TITLE
7.1 SURR
RETURN
AUTO
or
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
DOWN
UP
Enter the test tone mode.
HOME THEATER MASTER
RNC-220
6
DVD
TEST TONE
ꢁYou can select the desired channel and adjust its level
with repeating the steps ③and ④in “Adjusting each
channel level” procedure.
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
or
RETURN
AUTO
DSP
MODE
TEST
TONE
ST
DISC
.SCAN
TEST
TONE
CENTER
MOE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Cancel the test tone function.
8
ꢁThe test tone will be heard from the speaker of each
channel for 2 seconds as follows:
ꢂFront Left ꢂCenter ꢂFront Right ꢂSurround Right
Surround Left ((ꢅSurround Center) or (ꢅBack Left ꢅBack Right)) ꢅ
ꢂSUBwoofer
DVD
TEST TONE
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
or
RETURN
AUTO
DSP
MODE
TEST
TONE
ST
DISC
.SCAN
TEST
TONE
CENTER
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
ꢁDepending on the speaker setting (None or No), the test
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
tone of the corresponding channel is not available.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Downmixing into 2 front channels
ꢁAllows the multi - channel signals encoded in DTS,
Dolby Digital or MPEG format to be reproduced
through only two front speakers or through
headphones.
ꢁWhen the digital signals from the DTS, Dolby Digital
or MPEG program sources are input, press the
STEREO button.
ꢁTo cancel the 2 - CH downmix mode, select the
desired surround mode with using the MULTI
CONTROL knob or the DSP MODE button, etc.
ꢁWhen the playback of the source on the player is
stopped or interrupted, etc, the 2 - CH downmix
mode is not canceled even though “ DTS”,
“DOLBY DIGITAL” or “MPEG” indicator goes
off.
ꢁIf headphones are plugged in and the SPEAKER
button is set to off while the digital signals from the
DTS, Dolby Digital or MPEG program sources are
being input, it will enter the 2- CH downmix mode
automatically and if headphones are unplugged and
the SPEAKER button is set to on while in the 2 -CH
downmix mode, it will return to the previous mode.
DVD
STEREO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
or
MODE
ST
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁ“DTS”, “MPEG”or “DOLBY DIGITAL” indicators
lights up and “2CH DOWNMIX” is scrolled,
meaning it enters the 2 - CH downmix mode, and
then the discrete multi-channels(except LFE) are
mixed down into 2 front channels.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO RADIO BROADCASTS
Select the desired band.
Auto tuning
2
BAND
Select the tuner.
1
BAND
FREQUENCY
ꢁEach time this button is pressed, the band changes
DVD
as follows :
AUDIO
VOL. CH LEVEL
CH SEL
ꢂFM Stereo mode ꢂFM Mono mode ꢂAM
(“ STEREO” lights up ) ( “ STEREO” goes off)
ENTER
or
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
ꢁWhen FM stereo broadcasts are poor because of
weak broadcast signals, select the FM mono mode to
reduce the noise, then FM broadcasts are reproduced
in monaural sound.
VID1
VID2
VID3
VID5
TUNER
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁWhen pressing the BAND button without selecting
the TUNER, the tuner will be selected automatically.
Select the tuning mode.
Press the TUNING/PRESET UP(▲) or
DOWN(▼) button for more than 0.5 second.
T/P MODE
3
4
TUNING/PRESET
ꢁEach time this button is pressed, the mode changes
as follows:
ꢁThen “ AUTO” appears on the display. The tuner
will now search until a station of sufficient
strength has been found. The display shows the
tuned frequency and “TUNED”.
ꢂ Tuning mode : “PRESET” goes off.
Preset mode : “PRESET” lights up. ꢅ
ꢁIf the station found is not the desired one, simply
repeat this operation.
ꢁWeak stations are skipped during auto tuning.
Manual tuning
TUNING/PRESET
ꢁManual tuning is useful when you already know the frequency of the desired
transmitter.
ꢁPerform the steps ①~③in “Auto tuning” procedure and press the
TUNING/PRESET UP(▲) or DOWN(▼)button repeatedly until the right
frequency has been reached.
Press the MEMORY/ENTER button.
Presetting radio stations
ꢁYou can store up to 30 preferred stations in the
memory.
2
MEMO/ENTER
Tune in the desired station with auto or
manual tuning.
1
ꢁ“MEMO” is flickering for 5 seconds.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the desired preset number(1~30)
and press the MEMORY/ENTER button.
Repeat the above steps ①to ③to
memorize other stations.
3
4
TUNING/PRESET
MEMO/ENTER
ꢀMEMORY BACKUP FUNCTION
ꢁWhen using the NUMERIC buttons on the remote
control.
The following items, set before the receiver is turned
off, are memorized.
ꢁINPUT SELECTOR settings
ꢁSurround mode settings
Examples)
For “3” :
within 2 seconds
ꢁPreset stations, etc.
For “15” :
ꢀNote : If the electricity fails or the AC input cord is
disconnected for about 2 weeks, all
For “30” :
memorized settings will be lost.
ꢁThe station has now been stored in the memory.
ꢁWhen using the NUMERIC buttons, the station is stored
automatically without pressing the MEMORY/ ENTER
button.
ꢁA stored frequency is erased from the memory by storing
another frequency in its place.
ꢁIf “MEMO” goes off, start again from the above step ②.
Select the desired preset number.
Tuning to preset stations
TUNING/PRESET
2
After selecting the tuner as input source,
select the preset tuning mode.
1
ꢁWhen using the NUMERIC buttons on the remote
control.
T/P MODE
Examples)
For “3”:
within 2 seconds
For “15”:
within 2 seconds
(or
)
For “30”:
ꢁWhen selecting the desired preset number with the
NUMERIC buttons, the desired preset station will be
tuned to automatically without selecting the preset
tuning mode.
ꢁThen “PRESET” lights up.
Scanning preset stations in sequence
DVD
VOL. CH LEVEL
ꢁThe receiver will start scanning the stations in the
preset sequence and each station is received for 5
seconds.
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
DISC
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
ꢁAt the desired station, press this button again to
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
stop scanning.
HOME THEATER MASTER
RNC-220
26
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
ꢁThe analog signals from the 7.1 CH DIRECT inputs as well as the digital signals from the coaxial or optical
digital input can be heard but cannot be recorded.
ꢁThe volume, tone (bass, treble) settings,etc. have no effect on the recording signals.
Start recording on the component hooked
up to TAPE MONITOR.
Recording with TAPE MONITOR
2
Select the desired input as recording source
except TAPE MONITOR.
1
DVD
VOL. CH LEVEL
AUDIO
VIDEO
Start play on the desired input.
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
3
or
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
TUNER
VID1
CD
P
AUX
VID4
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
VID2
VID3
HOME THEATER MASTER
RNC-220
ꢁFor tape monitor function, refer to “TAPE MONITOR
function” on page 15.
ꢁBe sure that “TAPE MON” goes off.
Start recording on the component hooked
up to VIDEO 1.
Dubbing from video components onto
VIDEO 1
2
Select VIDEO 2, VIDEO 3 or VIDEO 4
as a recording source.
Start play on the component hooked up
to VIDEO 2, VIDEO 3 or VIDEO 4.
3
1
DVD
VIDEO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
or
AUTO
ꢁThe audio and video signals from the VIDEO 2,
VIDEO 3 or VIDEO 4 component will be dubbed
onto the VIDEO 1 and you can enjoy them on the TV
set and from the speakers.
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
VID2
VID3
VID4
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Select CD as the sound recording source.
Dubbing the sound and image signals
separately onto VIDEO 1
2
DVD
Example) When dubbing the VIDEO 2 image signal
and the CD sound signal separately onto
VIDEO 1.
VOL. CH LEVEL
AUDIO
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
or
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
Select VIDEO 2 as a image recording
source.
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
CD
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
1
DVD
VIDEO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
or
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
VID2
HOME THEATER MASTER
RNC-220
Image source Sound source
Image source Sound source
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Start recording on the component hooked
up to VIDEO 1.
Start play on the components hooked up to
VIDEO 2 and the CD respectively.
3
4
ꢁThe audio signal from the CD and the video signal
from the VIDEO 2 component will be dubbed and
you can enjoy them on the TV set and from the
speakers.
ꢀNote: Be sure to observe the order of the above
steps ①and ②.
DIGITAL AUDIO RECORDING WITH MD RECORDER
ꢁOnly when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD
recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original
signals. Refer to “ CONNECTING AUDIO COMPONENTS” and “CONNECTING DIGITAL INs and OUT” on
page 5 and 7 and the operating instructions of the MD recorder or CD recorder.
ꢀNotes:
ꢁDigital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc.
ꢁIn most DVDs as well as some CDs, etc., digital recording may not be available depending on the signal
format.
ꢁThere are some restrictions on recording digital signals. When making digital recordings, refer to the operating
instructions of your digital recording equipment to know what restrictions are imposed.
Select a desired input of CD, TAPE
MONITOR and VIDEO 1~VIDEO 4 as a
recording source.
For digital recording, select the desired
digital input as the recording signal input.
1
2
DIGITAL/ANALOG
DVD
INPUT SELECTOR
VIDEO
VOL. CH LEVEL
AUDIO
TAPE MON.
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
ꢁEach time this button is pressed, the corresponding
AUTO
or
DSP
MODE
input is selected as follows:
ꢂ DIGITAL ꢂ ANALOG
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
CD
T1/MON
VID3
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
VID1
VID2
VID4
HOME THEATER MASTER
RNC-220
ꢀNote: When the selected digital input is not
connected, “DIGITAL” is flickering. There
will be no recording as well as no sound.
Start play on the desired input.
Start recording on the component
connected to OPTICAL DIGITAL OUT.
4
3
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER FUNCTIONS
Compressing the dynamic range (Dolby Digital sources only)
ꢁThis function compresses the dynamic range of
previously specified parts of the Dolby Digital sound
track(with extremely high volume)to minimize the
difference in volume between the specified and non-
specified parts.
ꢁEach time this button is pressed, the mode changes
and disappears in 3 seconds as follows;
ꢆ
DYNAMIC : 0.0 : Off
ꢆ
This makes it easier to hear all of the sound track
when watching movies at night at low levels.
DYNAMIC : 0.5 : Low compression
ꢆ
DYNAMIC : 1.0 : High compression
ꢁWhen the digital signals from the Dolby Digital
program source are input.
ꢁIn some Dolby Digital software, this function may
not be available.
DYNAMIC
RANGE
Operating the sleep timer
Adjusting the brightness of the
fluorescent displays
ꢁThe sleep timer allows the system to continue to
operate for a specified period of time before
automatically shutting off.
ꢁTo set the receiver to automatically turn off after the
specified period of time.
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
DVD
TITLE
7.1 SURR
RETURN
AUTO
DSP
VOL. CH LEVEL
MODE
ST
CH SEL
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
ENTER
TUNER
CD
T1/MON
AUX
VID4
PHONO
RPT
A
INTRO
B
VID1
VID2
VID3
VID5
TITLE
7.1 SURR
SYS DISP
RETURN
SYS DISP
SLEEP
DIRECT IN
ROOM2
AUTO
DSP
MODE
HOME THEATER MASTER
RNC-220
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
SLEEP
VID
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁEach time this button is pressed, the brightness of
all fluorescent displays of Sherwood components
connected by the DIGI LINK III changes together
as follows:
ꢁEach time this button is pressed, the sleep time
changes and disappears in 3 seconds as follows:
ꢂ10 ꢂ20 ꢂ30 ꢂ60 ꢂ90 ꢂOFF
Unit : minutes
ꢂON ꢂdim ꢂOFF
ꢁWhile operating the sleep timer, “SLEEP” lights up.
ꢁWhen the sleep time is selected, all display panels of
Sherwood components connected by the DIGI LINK
III are dimly lit.
ꢁIn the display OFF mode, pressing any button will
restore the display ON mode.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the VIDEO LABEL button to enter the
video label mode.
Example) When selecting VIDEO 1.
Entering a video label
2
4
ꢁThis function can be operated only on video input
sources such as VIDEO 1~4.
Select the desired video input source to
enter its label.
VIDEO LABEL
1
DVD
VIDEO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
or
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
VID1
VID2
VID3
VID4
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Select the character on the flickering digit.
Confirm your selection.
VIDEO LABEL
MULTI CONTROL
3
ꢁThen the next digit will flicker.
ꢁEach time the MULTI CONTROL knob is rotated,
the characters change as follows:
Repeat the above steps ③and ④to enter
the desired characters on the rest of the
digits.
ꢇ
Blank (
ꢈ
Alphabets : A~Z, a~z
ꢈ
Numerals : 0~9
ꢈ
)
5
ꢁOn up to 9 digits, the desired characters can be entered.
ꢀNote: If any button such as “AUDIO”, “VIDEO”, “7.1
CH DIRECT” button, etc. is pressed while
entering a video label, the video label mode will
be canceled.
Symbols : ( ) ＋ ， ． ／
ꢉ
￣
MEMO/ENTER
Memorize the desired video label.
6
Repeat the steps ②~⑥in “Entering a
video label” procedure.
Correcting or clearing a video label
2
Select the desired video input source to be
rectified or cleared.
1
DVD
ꢁTo clear a video label, make a blank on each digit
and memorize it, then the video label is cleared and
its factory video input source will be displayed.
ꢁIf the VIDEO LABEL button is pressed for more
than 3 seconds, blanks will be made on all the digits
at once.
VIDEO
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
or
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
VID1
VID2
VID3
VID4
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ROOM 2 SOURCE PLAYBACK
ꢁThis function allows enjoying one source in the main room and playing another in a different room at the same
time.
ꢁThe analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals
from the coaxial or optical digital input cannot be output from the ROOM 2 OUTs, meaning no playback in a
different room.
ꢁWhen you connect the multi - room adapter to the MULTI - ROOM jack of this unit, you can control this unit
with its remote control unit in a different room, too. (For details, refer to “CONNECTING MULTI - ROOM
SYSTEM KIT” on page 8.)
Press the ROOM 2 button.
1
ꢁ“R2” will flicker for 3 seconds and the ROOM 2
function is activated.
ꢁTo cancel the ROOM 2 function, press it again.
DVD
ROOM2 FEED
VOL. CH LEVEL
CH SEL
ENTER
Then “R2” goes off
ꢁYou can cancel the ROOM 2 function with using
RPT
A
INTRO
B
TITLE
7.1 SURR
or
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
these buttons even in the standby mode.
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
ROOM2
HOME THEATER MASTER
RNC-220
Select the desired input as a ROOM 2
source while “R2” is flickering.
2
3
ꢁThe selected ROOM 2 source is displayed for 3
seconds as follows : (R2) TUNER, (R2) CD, (R2)
AUX, (R2) VIDEO 1~4.
ꢁOnly these sources can be played in another room.
ꢁWhen an audio program source is selected, as a
ROOM 2 source, the image of the video program
source selected previously can be played separately,
too.
(For details, refer to “SETTING THE ROOM 2
FEED SETUP”on page 44.)
ꢁOnly while “R2” is flickering, the volume level for
the ROOM 2 source can be adjusted.
ꢁWhen “R2” is not flickering and lights up, press the
DVD
VOL. CH LEVEL
AUDIO
VIDEO
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
or
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
TUNER
VID1
CD
P
AUX
VID4
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
VID2
VID3
HOME THEATER MASTER
RNC-220
ROOM 2 button again briefly twice.
Start play on the component related to the
ROOM 2 source.
ꢀNotes:
ꢁEven when this unit enters the standby mode, in
such a case that “R2” lights up still and the
STANDBY button lights up in blue as it does in the
operating mode, meaning only the ROOM 2 circuitry
operates, the ROOM 2 source selected previously
can be played independently.
ꢁWhen you do not use the ROOM 2 function, cancel
the ROOM 2 function to save electricity.
ꢁFor ROOM 2 volume adjustment, refer to “SETTING
THE ROOM 2 FEED SETUP” on page 44.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the OSD
This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to
simplify the setup procedures.
The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current
status display and menu screen.
■Notes: ꢁThe OSD function is not available via the component video connection.
ꢁAny on-screen display shown on the monitor TV will not be recorded onto VIDEO 1.
CURRENT STATUS DISPLAY
This mode shows the status corresponding to each operation.
ꢁThe on-screen display will automatically disappear in 5 seconds.
ꢁFor examples, there are 2 status displays as follows.
■Note:ꢁWhen watching a movie earnestly, if you want to turn off the current status display function, set the
OSD mode to Off.(For details, refer to “When selecting the OSD MODE” on page 40.)
ꢀWhen selecting the desired input source
ꢀWhen selecting the TEST TONE mode.
VIDEO 1 (OPTICAL1)
FL
:
------ ------
:
0 dB
Channel level or overall volume display
Input source
Signal input
ꢁWhen adjusting each channel level or overall volume, the
volume level display will be shown.
ꢁThe test tone display will be shown until the test tone mode is
canceled.
OSD Menu Settings
ꢁThe OSD menu allows you to perform the setup procedures easily. In most situations, you will only need to set this
once during the installation and layout of your home theater, and it rarely needs to be changed later. The OSD
menu consists of 5 main menus: speaker setup, function select, surround setup, CH level trim and room 2 feed
setup. Some of these menus are divided up into various sub-menus.
ꢁThe OSD menu settings are performed easily with the CURSOR control(▲, ▼, ◀, ▶), ON-SCREEN DISPLAY,
RETURN and ENTER buttons.
ꢁThe “3”, “7”, “8” and “9” of the NUMERIC buttons do also work as the CURSOR control(▲, ▼, ◀, ▶)buttons do. In
this case, the “3” button stands for the CURSOR UP(▲) button, the “7” for the CURSOR LEFT(◀), the “8” for the
CURSOR DOWN(▼) and the “9” for the CURSOR RIGHT(▶).
Turn the menu screen on.
M A I N M E N U
1
DVD
S P E A K E R S E T U P
F U N C T I O N S E L E C T
S U R R O U N D S E T U P
C H L E V E L T R I M
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
R O O M 2 F E E D S E T U P
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
O S D : Q u i t
E N T E R : S e l e c t
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁIn the bottom of the display, “OSD” stands for the ON-
SCREEN DISPLAY button, “RETURN” for “RETURN”,
“ENTER” for “ENTER”, “▲”, “▼”, “◀” and “▶” for
ꢁThe main menu will be shown.
CURSOR UP(▲), DOWN(▼), LEFT(◀) and RIGHT(▶).
ꢁTo turn the menu screen off, press this button again.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the desired menu using the CURSOR
DVD
UP(▲), DOWN(▼) buttons.
VOL. CH LEVEL
2
3
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Confirm your selection.
DVD
VOL. CH LEVEL
■When selecting the SPEAKER SETUP.
OSD
CH SEL
ENTER
ENTER
RPT
INTRO
A
B
TITLE
S P E A K E R S E T U P
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
TEST
TONE
CENTER
MODE
P.SCAN
TUNER
CD
T1/MON
AUX
VID4
PHONO
S P E A K E R C O N F I G
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
S P E A K E R D I S T A N C E
L F E L E V E L C O N T R O L
34
HOME THEATER MASTER
RNC-220
ꢁThe selected category or item will provide the
R E T U R N : B a c k
E N T E R : S e l e c t
needed setting details using the subsequent screens.
■When selecting the FUNCTION SELECT.
F U N C T I O N S E L E C T
■When selecting the SURROUND SETUP.
S U R R O U N D S E T U P
Off
S O U R C E D I R E C T
:
:
I N P U T S E T U P
AUTO
D E C O D I N G M O D E
D O L B Y D I G I T A L
T O N E C O N T R O L
O S D M O D E
37
41
C I N E M A E Q
:
Off
R E T U R N : B a c k
,
: S e l e c t
R E T U R N : B a c k
E N T E R : S e l e c t
■When selecting the CH LEVEL TRIM.
■When selecting the ROOM2 FEED SETUP.
C H L E V E L T R I M
R O O M 2 F E E D S E T U P
F L
C
:
:
:
:
:
:
:
:
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
dB
dB
dB
dB
dB
dB
dB
dB
F R
S R
B R
B L
S L
S W
V O L U M E M O D E
44
43
F U N C T I O N S E L E C T
R E T U R N : B a c k
E N T E R : S e l e c t
R E T U R N : B a c k
,
: S e l e c t
ꢁFor the setting details, see page in ꢊ.
ꢁAdjust the setting(s) in each setting category to your preference.
ꢁWhen the RETURN button is pressed on a sub-menu, the previous menu is recalled.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE SPEAKER SETUP
ꢁAfter you have installed this unit and connected all the components, you first perform the speaker setup settings for
the optimum sound acoustics according to your environment and speaker layout.
To select the sizes of the speakers that are connected.
S P E A K E R S E T U P
To enter the distance between the listening position and
each speaker to set the delay time automatically for
the optimum surround playback.
S P E A K E R C O N F I G
S P E A K E R D I S T A N C E
L F E L E V E L C O N T R O L
To adjust LFE(Low Frequency Effect) levels included in
Dolby Digital, DTS and MPEG program sources.
R E T U R N : B a c k
E N T E R : S e l e c t
When selecting the SPEAKER CONFIG
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the SPEAKER CONFIG, then press the ENTER
button.
1
DVD
S P E A K E R C O N F I G
VOL. CH LEVEL
Yes
SUBWOOFER :
CH SEL
Large
Large
Large
FRONT
CENTER
SURROUND
SURR.BACK
S/B CH
:
:
:
:
:
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
2CH
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
Small
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker.
2
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ꢁEach time these buttons are pressed, “◀” and “▶” are
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
moved to the corresponding speaker mode.
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired mode.
3
DVD
ꢁDepending on your speaker type, you can select one of these following speaker types.
VOL. CH LEVEL
ꢁYes/No : Select the desired depending on whether a subwoofer is connected or not.
ꢁLarge : Select this when connecting speakers that can fully reproduce sounds below 80 Hz.
ꢁSmall : Select this when connecting speakers that cannot fully reproduce sounds below 80 Hz.
When this is selected, sounds below 80 Hz are sent to the subwoofer.
CH SEL
ENTER
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
ꢁNone : Select this when no speakers are connected.
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
When this is selected, sounds are sent to the front speakers.
HOME THEATER MASTER
RNC-220
ꢁ2CH/1CH : Select the desired depending on the number of surround back speakers.
ꢀNotes :
ꢁWhen “FRONT’ is set to “Small”, “SUBWOOFER” is automatically set to “Yes”, and when “SUBWOOFER” is set to
“No”, “FRONT” is automatically set to “Large”.
ꢁWhen “FRONT” is set to “Small”, “CENTER”, “SURROUND” and “S/B CH” cannot be set to “Large”.
ꢁWhen “SURROUND” is set to “None”, “SURR. BACK” cannot be selected.
ꢁWhen “CENTER” is set to “None”, “SURROUND” cannot be set to “None” and vice versa.
ꢁWhen “SURROUND” is set to “Small”, “S/B CH” cannot be set to “Large”.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat the above steps ②and ③until the speakers are all set to the desired mode.
4
When selecting the SPEAKER DISTANCE
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the SPEAKER DISTANCE, then press the
ENTER button.
1
DVD
S P E A K E R D I S T A N C E
VOL. CH LEVEL
Meters
U N I T
F R O N T
F R O N T
C E N T E R
S U R R .
S U R R .
:
:
:
:
:
:
CH SEL
L
R
3 . 0 m
3 . 0 m
3 . 0 m
3 . 0 m
3 . 0 m
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
L
R
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the unit.
2
3
4
DVD
ꢁThen “◀” and “▶” are moved to the unit mode.
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired unit.
DVD
ꢁEach time these buttons are pressed, “Meters” or “Feet” is
selected.
ꢁOnce a unit is selected, the distances are automatically
changed in the selected unit.
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker.
ꢁThen “◀” and “▶” are moved to its distance.
ꢁYou cannot select the subwoofer, surround back speakers and the speakers set to “None”.
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to enter the distance from the selected speaker to the
listening position.
5
ꢁYou can set the distance within the range of 0.3~9 meters in 0.3 meter intervals(or 1~30 feet in 1 feet intervals)
Repeat the above steps ④and ⑤until the distances are all entered.
6
35
Download from Www.Somanuals.com. All Manuals Search And Download.
When selecting the LFE LEVEL CONTROL
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the LFE LEVEL CONTROL, then press the
ENTER button.
1
L F E L E V E L C O N T R O L
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
ENTER
D O L B Y
D T S
M P E G
-----
-----
-----
+
+
+
0
0
0
dB
dB
dB
TITLE
7.1 SURR
RETURN
AUTO
-----
-----
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired LFE level mode.
2
3
ꢁEach time these buttons are pressed, “▶” is moved to the
corresponding LFE level mode.
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the selected LFE level as desired.
ꢁEach time these buttons are pressed, the LFE level can be
adjusted within the range of either -10~0 dB for Dolby
DVD
VOL. CH LEVEL
Digital program sources or -10~+10 dB for DTS and MPEG
program sources.
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ꢁIn general, we recommend the LFE level for Dolby Digital
program sources to be set at 0 dB and +10 dB for DTS
program sources.(However, the recommended LFE level for
some early DTS program sources is 0 dB.)
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
If the recommended levels seem too high, lower the setting
as necessary.
Repeat the above steps ②and ③until each level is adjusted as desired.
4
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE FUNCTION SELECT
F U N C T I O N S E L E C T
To adjust the input source as desired.
To adjust the tone as desired.
I N P U T S E T U P
T O N E C O N T R O L
O S D M O D E
To select the desired OSD mode.
R E T U R N : B a c k
E N T E R : S e l e c t
ꢀNote:
ꢁWhen the source direct function is selected, the TONE CONTROL cannot be selected.
When selecting the INPUT SETUP
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the INPUT SETUP, then press the ENTER button.
1
DVD
I N P U T S E T U P
To match the connected
DIGITAL INs to the desired
input sources respectively.
VOL. CH LEVEL
CH SEL
D I G I T A L I N S E T U P
V I D E O S E L E C T
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
To select a video input source.
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
E N T E R : S e l e c t
HOME THEATER MASTER
RNC-220
ꢀWhen selecting the DIGITAL IN SETUP
ꢁYou can match the connected DIGITAL INs to the desired of CD, TAPE MONITOR and VIDEO 1~4.
(For details, refer to “CONNECTING DIGITAL INs and OUT” on page 7.)
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the DIGITAL IN SETUP, then press the ENTER
button.
2
DVD
D I G I T A L I N S E T U P
VOL. CH LEVEL
COAX1
OPT2
COAX2
OPT1
None
C D
:
:
:
:
:
:
CH SEL
T A P E M O N
V I D E O 1
V I D E O 2
V I D E O 3
V I D E O 4
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
OPT3
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
ꢁ“OPT3” means the OPTICAL IN on the front panel.
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired input source.
3
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
ꢁEach time these buttons are pressed, “◀” and “▶” are
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
moved to the corresponding DIGITAL IN.
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired DIGITAL IN.
4
5
ꢁEach time these buttons are pressed, the DIGITAL INs change.
ꢀNotes:
ꢁBecause there are 5 DIGITAL INs on the rear and front panels, one
of CD, TAPE MONITOR and VIDEO 1~4 cannot be matched a
DIGITAL IN to.
In this case, you do select “None” instead of a DIGITAL IN.
ꢁWhen the input source set to “None” is selected, the analog input is
automatically selected.
DVD
VOL. CH LEVEL
CH SEL
ENTER
T
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁIn such a case that a DIGITAL IN is matched to two input sources or
more, when these input sources are selected, the digital audio signals
can be heard from the same DIGITAL IN.
Repeat the above steps ③and ④until the connected DIGITAL INs are matched to the desired input
sources respectively.
ꢀWhen selecting the VIDEO SELECT
ꢁYou can also select a video input source on the OSD menu and enjoy it without pressing the VIDEO SELECTOR
button(s).
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the VIDEO SELECT, then press the ENTER
button.
2
DVD
V I D E O S E L E C T
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
ENTER
VID 1
V I D E O I N
:
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired video input source.
3
DVD
ꢁEach time these buttons are pressed, the video input source
changes.
VOL. CH LEVEL
CH SEL
ENTER
P
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
38
Download from Www.Somanuals.com. All Manuals Search And Download.
When selecting the TONE CONTROL
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the TONE CONTROL, then press the ENTER
button.
1
T O N E C O N T R O L
DVD
VOL. CH LEVEL
T O N E D E F E A T
:
Off
CH SEL
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
B A S S
T R E B L E
-----
-----
+
+
-----
-----
0
0
dB
dB
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
ꢀNote:
ꢁWhen the source direct function is activated, the TONE CONTROL cannot be selected.
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired tone defeat mode.
2
ꢁEach time these buttons are pressed, the tone defeat mode
changes as follows:
DVD
On : Select this when listening to a program source without
VOL. CH LEVEL
CH SEL
↕ the tone effect.
Off : Select this when adjusting tone for your taste .
ENTER
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
ꢀNote:
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢁWhen the tone defeat mode is set to On, the tone (bass and
treble) cannot be adjusted.
ꢀWhen the tone defeat mode is set to Off to adjust the tone (bass and treble)
1. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired tone mode.
ꢁEach time these buttons are pressed, “▶” is moved to the tone defeat mode or the corresponding tone mode.
2. At the desired tone mode, press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the selected tone as desired.
ꢁThe tone level can be adjusted within the range of -10~+10 dB.
ꢁIn general, we recommend the bass and treble to be adjusted to 0 dB(flat level).
ꢁExtreme settings at high volume may damage your speakers.
3. To complete tone adjustment, repeat the above steps 1 and 2.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
When selecting the OSD MODE
ꢁWhen the OSD MODE is set to On, the current status display overlays the program image on the monitor TV and may
interfere with your movie enjoyment. In such a case, set the OSD MODE to Off.
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the OSD MODE, then press the ENTER button.
1
O S D M O D E
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
O S D D I S P L A Y
:
On
ENTER
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
R E T U R N : B a c k
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired OSD mode.
2
ꢁEach time these buttons are pressed, the OSD mode changes
as follows:
DVD
VOL. CH LEVEL
On : To turn on the current status display.
CH SEL
ENTER
PT
A
INTRO
B
↕
TITLE
7.1 SURR
RETURN
AUTO
DSP
Off : To turn off the current status display.
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE SURROUND SETUP
S U R R O U N D S E T U P
To select the source direct function for pure sound quality or not.
Off
S O U R C E D I R E C T
:
:
AUTO
To select the desired decoding mode.
To select the desired surround mode.
D E C O D I N G M O D E
D O L B Y D I G I T A L
To select the cinema EQ function or not.
C I N E M A E Q
:
Off
R E T U R N : B a c k
,
: S e l e c t
ꢀNotes :
ꢁOnly when the digital input is selected as signal input, the decoding mode and the surround mode can both be
selected as desired.
ꢁWhen the analog input is selected, only the surround mode can be selected.
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired item.
1
ꢁEach time these buttons are pressed, “◀” and “▶” are
moved to the corresponding mode.
DVD
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired mode.
2
DVD
ꢁEach time these buttons are pressed, the modes change as
follows according to the selected item :
VOL. CH LEVEL
CH SEL
ENTER
PT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
When selecting the SOURCE DIRECT
ꢁOnly when playing program sources in analog stereo or digital 2 ch PCM format, the SOURCE DIRECT can be selected.
On : Select this to achieve the pure sound quality.
When this is selected, the stereo mode is automatically selected and the pure sound that bypasses the tone circuitry
will be heard.
Off : Select this to cancel the source direct function.
↕
ꢀNotes :
ꢁWhen the SOURCE DIRECT is set to On, DECODING MODE, surround mode and CINEMA EQ cannot be selected.
ꢁWhen you select the 7.1 CH DIRECT as input source or the digital signals from DTS, Dolby Digital or MPEG sources,
etc. are input, the source direct function is automatically canceled.
When selecting the CINEMA EQ
ꢁWhen 96 kHz PCM(2 channel stereo) signals are input or the source direct function is selected, the cinema EQ
function can not be selected.
On : Select this to compensate for edgy or shrill movie sound tracks.
↕
Off : Select this to cancel the cinema EQ function.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
When selecting the DECODING MODE
ꢁDepending on the input digital signal format, you can select the desired decoding mode.
Auto : Select this for automatic detection of a digital input signal format.
The input digital signal format (DTS, Dolby Digital, MPEG or PCM(2 channel stereo), etc.) used by the selected digital
input source is detected automatically to perform the necessary decoding process for optimum surround modes.
Dolby Digital : Select this for Dolby Digital signal processing. The decoding process is preformed only when Dolby Digital
signals are input.
DTS : Select this for DTS signal processing. The decoding process is performed only when DTS signals are input.
MPEG : Select this for MPEG signal processing. The decoding process is performed only when MPEG signals are input.
PCM : Select this for PCM signal processing. The decoding process is performed only when PCM signals are input.
ꢀNotes :
ꢁSurround sound effect will not work properly if the signal passes through a graphic equalizer.
Please refer to your equalizer operating instructions for guidance on switching off(or defeating) the equalizer.
ꢁOnly when the digital input is selected as signal input for the input sources except TUNER and AUX, the decoding mode can be
selected.
ꢁNoise may be generated at the beginning of playback and while searching during DTS playback in the auto mode. In this case,
try playing in the DTS mode.
When selecting the surround mode
ꢁDepending on the input signal format and the selected decoding mode, you can select the desired surround mode as follows:
* When Dolby Digital signals are input in the auto or Dolby Digital mode, the following modes can be selected.
→DOLBY DIGITAL(↔DOLBY PRO LOGIC II MOVIE ↔DOLBY PRO LOGIC II MUSIC ↔DOLBY PRO LOGIC)↔DOLBY VIRTUAL ←
Only when Dolby Digital 2.0 channel signals are input, the surround modes in ( ) can be selected, too.
* When PCM(2 channel stereo) signals are input in the auto or PCM mode, the following modes can be selected.
→DOLBY PRO LOGIC II MOVIE ↔DOLBY PRO LOGIC II MUSIC ↔DOLBY PRO LOGIC ↔DOLBY VIRTUAL ↔DTS NEO MOVIE ↔DTS NEO MUSIC ←
→MATRIX ↔GAME ↔ARENA 2 ↔ARENA 1 ↔CLUB 2 ↔CLUB 1 ↔CHURCH ↔STADIUM ↔HALL 2 ↔HALL 1↔MOVIE ↔THEATER ←
ꢁWhen the analog input is selected as signal input and analog stereo signals are input, you can select the desired of these above
surround modes, too.
ꢁHowever, when DTS or MPEG signals are input in the following decoding modes, the corresponding surround mode will be
automatically selected:
* When DTS signals are input in the auto or DTS mode, the corresponding DTS mode will be selected.
* When MPEG signals are input in the auto or MPEG mode, MPEG mode will be selected.
ꢀNotes :
ꢁWhen the selected decoding mode is not matched to the input signal format, the indicator of the signal being input is flickering,
meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding
mode and the available surround mode according to the input signal format.
ꢁWhen the 7.1 CH DIRECT is selected as an input source, the surround mode cannot be selected.
ꢀTo play some multi-channel program sources in the Extra Surround 6.1/7.1 mode,
ꢁWhen the digital signals from the following program sources only are input in the available decoding mode, press the EXTRA
SURROUND 6.1/7.1 button on the front panel or the 7.1 CH SURROUND button on the remote control, then the
corresponding surround mode will be selected.
* Dolby Digital 5.1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX technology) :
EXTRA SURROUND mode,
* DTS 5.1-channel sources : DTS ES MATRIX mode.
ꢁPress the EXTRA SURROUND 6.1/7.1 button or the 7.1 CH SURROUND button again to cancel the 6.1(or 7.1) surround mode.
ꢁAccording to whether the surround back speaker is set to “1 CH” or “2 CH”, the 6.1 or 7.1 mode is selected.
ꢁHowever, when the surround back speaker is set to “None”, the Extra Surround 6.1/7.1 mode cannot be activated.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE CH LEVEL TRIM
C H L E V E L T R I M
F L
C
:
:
:
:
:
:
:
:
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
------ ------
:
:
:
:
:
:
:
:
0
0
0
0
0
0
0
0
dB
dB
dB
dB
dB
dB
dB
dB
F R
S R
B R
B L
S L
S W
R E T U R N : B a c k
,
: S e l e c t
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired channel.
1
2
DVD
ꢁEach time these buttons are pressed, “▶” is moved to the
corresponding channel.
ꢀNote :
ꢁDepending on the speaker settings such as “None” and
“No”, center, surround, surround back or subwoofer
channel will not be selected.
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to adjust the level of the selected channel as desired.
DVD
ꢁEach time these buttons are pressed, the channel level can
be adjusted within the range of -15~+15 dB.
VOL. CH LEVEL
CH SEL
ENTER
T
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
Repeat the above steps ①and ②to adjust each channel level until the sound level of each speaker is heard
to be equally loud.
3
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE ROOM2 FEED SETUP
R O O M 2 F E E D S E T U P
To select the desired volume mode.
To select the desired ROOM 2 source.
V O L U M E M O D E
F U N C T I O N S E L E C T
R E T U R N : B a c k
E N T E R : S e l e c t
ꢁThe ROOM 2 function allows you to enjoy one source in the main room while playing another in a different room at
the same time.
ꢁThe analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals from
the coaxial or optical digital input cannot be output from the ROOM2 OUTs.
When selecting the VOLUME MODE
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the VOLUME MODE, then press the ENTER
button.
1
DVD
V O L U M E M O D E
VOL. CH LEVEL
CH SEL
ENTER
RPT
A
INTRO
B
ENTER
V O L U M E M O D E
R E T U R N : B a c k
:
Variable
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
,
: S e l e c t
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired volume mode for the ROOM 2
source.
2
ꢁEach time these buttons are pressed, the volume mode
changes as follows:
DVD
VOL. CH LEVEL
Variable : Select this when an power amplifier is connected
CH SEL
to the ROOM 2(audio) OUTs for ROOM 2 source
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
playback. You can adjust the ROOM 2 volume
level with the MASTER VOLUME CONTROL
knob of this receiver or the VOLUME
AUTO
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
↕
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
UP/DOWN buttons on the remote control.
Fixed : Select this when an integrated amplifier, etc. is
connected to the ROOM 2(audio) OUTs. You can
adjust the ROOM 2 volume level on the connected
integrated amplifier, etc.
ꢀNotes :
ꢁWhen selecting the Fixed mode, first adjust the volume level as desired in the Variable mode and select the
Fixed mode. Then the volume level will be fixed to the adjusted level.
ꢁIn case that an integrated amplifier, etc. is connected to the ROOM 2(audio) OUTs and the volume mode is set to
Variable, if the ROOM 2 volume level is adjusted to high level on both this receiver and the connected amplifier,
the ROOM 2 speaker and the connected amplifier may be damaged.
Therefore, be sure to set the volume mode to Fixed for safe operation when using amplifier or receiver with its
own volume control for ROOM 2.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
When selecting the FUNCTION SELECT for ROOM 2
Press the CURSOR UP(▲)/DOWN(▼) buttons to select the FUNCTION SELECT for ROOM 2 source,
then press the ENTER button
1
F U N C T I O N S E L E C T
DVD
VOL. CH LEVEL
R O O M 2 F E E D
T U N E R
C D
:
Off
CH SEL
V I D E O 1
V I D E O 2
V I D E O 3
V I D E O 4
ENTER
RPT
A
INTRO
B
ENTER
TITLE
7.1 SURR
RETURN
AUTO
A U X
DSP
MODE
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
E N T E R : S e t
,
,
,
: M o v e
HOME THEATER MASTER
RNC-220
Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the ROOM 2 FEED mode as desired.
2
ꢁEach time these buttons are pressed, the ROOM 2
FEED mode is changed to “On” or “Off”.
ꢁWhen the ROOM 2 FEED mode is set to “Off”, the
ROOM 2 source cannot be selected.
DVD
VOL. CH LEVEL
CH SEL
ENTER
RT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
MODE
ꢁWhen you do not use the ROOM 2 function, set the
ST
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
ROOM 2 FEED mode to Off to save electricity.
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
ꢀWhen the ROOM 2 FEED mode is set to On
Press the CURSOR UP(▲)/DOWN(▼)/LEFT(◀)/RIGHT(▶) buttons to select the desired ROOM 2
source, then press the ENTER button.
3
ꢁEach time the CURSOR CONTROL buttons are
pressed, “+” is moved to the corresponding input
DVD
source.
VOL. CH LEVEL
CH SEL
ꢁWhen the audio input source is selected, a video input
source can be marked with “+”, too.
ENTER
RPT
A
INTRO
B
TITLE
7.1 SURR
RETURN
AUTO
DSP
ENTER
MODE
ST
It means that the image of the video input source
selected previously can be played separately, too.
DISC
.SCAN
TEST
TONE
CENTER
MODE
P
TUNER
CD
T1/MON
AUX
VID4
PHONO
VID1
VID2
VID3
VID5
SYS DISP
SLEEP
DIRECT IN
ROOM2
HOME THEATER MASTER
RNC-220
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
If a fault occurs, run through the table below before taking your unit for repair.
If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult
your dealer. Under no circumstances should you repair the unit yourself as this could invalidate the warranty!
PROBLEM
POSSIBLE CAUSE
REMEDY
• Connect cord securely.
• Check the outlet using a lamp or another appliance.
No power
No sound
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet is
dead or off.
• Check the speaker connections.
• Adjust the master volume.
• Press the MUTE button to cancel the muting effect.
• Select the available decoding mode.
• The speaker wires are disconnected.
• The master volume is adjusted too low.
• The MUTE button is pressed to ON.
• The selected decoding mode is not matched to the
input signal format.
• Select the desired input source correctly.
• Make connections correctly.
• Incorrect selection of input source.
• Incorrect connections between the components.
• Select a surround mode.
No sound from the surround
speakers
• Surround mode is switched off(normal stereo mode).
• Master volume and surround level are too low.
• Monaural source is used.
• Adjust master volume and surround level.
• Select a stereo or surround source.
• Select the desired surround speaker setting.
• Surround speaker setting is “None”.
• Select the desired surround mode.
• Select the desired (front) center speaker setting.
• Adjust master volume and center level.
No sound from the (front) center
speaker
• Dolby Virtual, normal stereo mode, etc is selected.
• (Front) center speaker setting is “None”.
• Master volume and center level are too low.
• Under the proper situations, perform the 7.1(or 6.1)
surround playback.(For details, refer to
No sound from the surround back
speakers
• The input signal format or the current surround
mode cannot support the 7.1(or 6.1) surround.
“ENJOYING SURROUND SOUND” on page 21.)
• Adjust master volume and surround back level.
• Select the desired surround back speaker setting.
• Master volume and surround back level are too low.
• Surround back speaker setting is “None”.
• Connect an antenna.
Stations cannot be received
• No antenna is connected.
• Tune in the desired station frequency.
• Move antenna and retry tuning.
• The desired station frequency is not tuned in.
• Antenna is in wrong position.
• Memorize the correct station frequency.
• Memorize the stations again.
Preset stations cannot be received
Poor FM reception
• An incorrect station frequency has been memorized.
• The memorized stations are cleared.
• Connect an antenna.
• No antenna is connected.
• Change the position of the antenna.
• The antenna is not positioned for the best reception.
• Change the position of the antenna.
• Install an outdoor FM antenna.
Continuous hissing noise during FM
reception, especially when a stereo
broadcast is received.
• Weak signals.
• Keep the receiver away from noise sources.
• Install an outdoor AM antenna.
Continuous or intermittent hissing
noise during AM reception,
especially at night.
• Noise is caused by motors, fluorescent lamps or
lightning, etc.
• Replace the batteries.
• Remove the obstacle.
Remote control unit does not
operate.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
• Make proper DIGI LINK connections.
Other Sherwood components do
not react to remote control
commands.
• DIGI LINK connections are not made properly.
• Clear it using “To clear a video label”. (Refer to
“Correcting or clearing a video label” on page 30)
A video label cannot be displayed.
OSD function is not available.
• Malfunction due to external influences such as
static electricity, etc.
• Make proper video connections.
• Video connections between this unit and the
monitor TV are not made correctly.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
ꢀAMPLIFIER SECTION
ꢁPower output, stereo mode, 8 Ω, THD 0.05%, 20 Hz~20 kHz.......................................................................................................... 2×100 W
ꢁTotal harmonic distortion, 8 Ω, 100 W, 1 kHz........................................................................................................................................ 0.05 %
ꢁIntermodulation distortion
60 Hz : 7 kHz = 4 : 1 SMPTE, 8 Ω, 100 W............................................................................................................................................. 0.09 %
ꢁInput sensitivity/impedance
Line (CD, TAPE, VIDEO) ......................................................................................................................................................... 200 mV/47 kΩ
ꢁSignal to noise ratio, IHF “A” weighted
Line (CD, TAPE, VIDEO)........................................................................................................................................................................ 98 dB
ꢁFrequency response
LINE (CD, TAPE, VIDEO), 10~100,000 Hz...................................................................................................................................... +0, -3 dB
ꢁOutput level
TAPE REC, 1 kΩ................................................................................................................................................................................... 180 mV
PRE OUT(Front, Center, Surround, Surround back, Subwoofer), 1 kΩ ................................................................................................... 1.0 V
ꢁBass/Treble control, 100 Hz/10 kHz..................................................................................................................................................... ±10 dB
ꢁSurround mode, only channel driven
Front power output, 8 Ω, 1 kHz, THD 0.7 %.............................................................................................................................. 110 W+110 W
Center power output, 8 Ω, 1 kHz, THD 0.7 %......................................................................................................................................... 110 W
Surround power output, 8 Ω, 1 kHz, THD 0.7 % ....................................................................................................................... 110 W+110 W
Surround back power output, 8 Ω, 1 kHz, THD 0.7 %............................................................................................................... 110 W+110 W
ꢀDIGITAL AUDIO SECTION
ꢁSampling frequency.................................................................................................................................................... 32, 44.1, 48, 96, 192 kHz
ꢁDigital input level
Coaxial, 75 Ω........................................................................................................................................................................................ 0.5 Vp-p
Optical, 660 nm............................................................................................................................................................................. -15~-21 dBm
ꢀVIDEO SECTION
ꢁVideo format............................................................................................................................................................................................. NTSC
ꢁInput sensitivity(=Output level), 75 Ω
Video(Composite (normal))..................................................................................................................................................................... 1 Vp-p
S-Video(luminance signal)...................................................................................................................................................................... 1 Vp-p
(chrominance signal) .......................................................................................................................................................... 0.286 Vp-p
Component video(R-Y signal).............................................................................................................................................................. 0.5 Vp-p
(B-Y signal) .............................................................................................................................................................. 0.5 Vp-p
(Y signal) .................................................................................................................................................................. 1.0 Vp-p
ꢀFM TUNER SECTION
ꢁTuning frequency range.............................................................................................................................................................. 87.5~108 MHz
ꢁUsable sensitivity, THD 3 %, S/N 30 dB.............................................................................................................................................. 17.2 dBf
ꢁ50 dB quieting sensitivity, mono/stereo ....................................................................................................................................... 25.2/43.2 dBf
ꢁSignal to noise ratio, 65 dBf, mono/stereo........................................................................................................................................... 72/68 dB
ꢁTotal harmonic distortion, 65 dBf, 1 kHz, mono/stereo...................................................................................................................... 0.2/0.3 %
ꢁFrequency response, 20 Hz~15 kHz .................................................................................................................................................... ±1.5 dB
ꢁStereo separation, 1 kHz............................................................................................................................................................................ 45 dB
ꢁCapture ratio............................................................................................................................................................................................. 3.0 dB
ꢁIF rejection ratio...................................................................................................................................................................................... 120 dB
ꢀAM TUNER SECTION
ꢁTuning frequency range .............................................................................................................................................................. 520~1710 kHz
ꢁUsable sensitivity.................................................................................................................................................................................. 12.5 mV
ꢁSignal to noise ratio.................................................................................................................................................................................... 51dB
ꢁSelectivity.................................................................................................................................................................................................. 30 dB
ꢀGENERAL
ꢁPower supply........................................................................................................................................................................... AC 120 V, 60 Hz
ꢁPower consumption.................................................................................................................................................................................... 3.8 A
ꢁSwitched AC outlets................................................................................................................................................... TOTAL 1A, 100 W max.
ꢁDimensions(W×H ×D) ...................................................................................................... 440×166×380 mm(17-3/8×6-1/2×15 inches)
ꢁWeight(Net)................................................................................................................................................................................ 17 kg(37.5 lbs)
Note: Design and specifications are subject to change without notice for improvements.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
O
P
E
R
A
T
I
N
G
I
N
S
T
R
U
C
T
I
O
N
S
R-863
AUDIO/VIDEO SURROUND RECEIVER
5707-21053-001-0
Download from Www.Somanuals.com. All Manuals Search And Download.
|