R-930AK
R-930AW
SERVICE MANUAL
S6710R930APW/
CONVECTION
MICROWAVE OVEN
MIX CONV
DEFROST
SENSOR
COOK
L
B
S
O
Z
K
G
H
E
L
P
Interactive
CUSTOM
HELP
SENSOR
REHEAT
MINUTE
PLUS
POPCORN
ELEVATE PKG
COMPU
DEFROST
1
2
3
4
5
6
7
8
Baked potatoes
Frozen
vegetables
Fresh
veg-soft
Fresh veg-hard
Frozen entrees
Hot dogs
SENSOR
COOKT
Bacon
Fish, seafood
Convection
Hamburgers
pieces
1
2
3
4
Chicken
Steaks
Fish steaks
COMPU
BROIL
1
2
3
4
Chicken
Turkey
COMPU
ROAST
Turkey
breast
Bundt
cake
Cookies
Pork
1
2
3
4
COMPU
BAKE
Muffins
French fries
MODELS
PREHEAT
CONVEC
BROIL
SLOW
COOK
LOW MIX
BAKE
HIGH MIX
ROAST
R-930AK
R-930AW
1
2
3
4
5
100˚F
150˚F
275˚F
300˚F
325˚F
6
7
8
9
350˚F
375˚F
0
ST OP
TCLEAR
400˚F
425˚F
150˚F
KITCHEN
TIMER
CLOCK
POWER
LEVEL
START
TOUCH ON
R-930AW
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICE TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ...................INSIDE FRONT COVER
BEFORE SERVICING ........................................................................................................................................... 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD.......................................................................................................................................................... 3
PRODUCT SPECIFICATIONS .............................................................................................................................. 4
GENERAL INFORMATION................................................................................................................................... 4
OPERATION .......................................................................................................................................................... 6
TROUBLESHOOTING GUIDE ............................................................................................................................13
TEST PROCEDURE ............................................................................................................................................14
TOUCH CONTROL PANEL .................................................................................................................................21
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 27
PICTORIAL DIAGRAM ........................................................................................................................................33
CONTROL PANEL CIRCUIT ...............................................................................................................................34
PRINTED WIRING BOARD .................................................................................................................................35
PARTS LIST ........................................................................................................................................................36
PACKING AND ACCESSORIES ......................................................................................................................... 39
SHARP ELECTRONICS CORPORATION
Service Headquarters:
Sharp Plaza,
Mahwah,
New Jersey
07430-2135
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately 1- (800) 237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
ServicepersonnelshouldinformSHARPELECTRONICSCORPORATIONofanycertifiedunitfound
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
shouldnotexceed1mW/cm2 atanypoint5cmormorefromtheexternalsurfaceoftheoven, measuredpriortoacquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches
Primary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of the requirement
as above mentioned, secondary interlock switch shall prevent microwave radiation emission in excess of 5 mW/cm2 at
any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5˚C (68˚F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
Theplacingofthisstandardloadintheovenisimportantnotonlytoprotecttheoven,butalsotoinsurethatanyleakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
SERVICE MANUAL
PRODUCT DESCRIPTION
CONVECTION
MICROWAVE OVEN
GENERAL INFORMATION
OPERATION
R-930AK / R-930AW
FOREWORD
This Manual has been prepared to provide Sharp Electronics
Corp. Service Personnel with Operation and Service Informa-
tion for the SHARP CONVECTION MICROWAVE OVENS R-
930AK / R-930AW.
TROUBLESHOOTING GUIDE
AND TEST PROCEDURE
It is recommended that service personnel carefully study the
entire text of this manual so that they will be qualified to render
satisfactory customer service.
Check the interlock switches and the door seal carefully.
Special attention should be given to avoid electrical shock and
microwave radiation hazard.
TOUCH CONTROL PANEL
COMPONENT REPLACEMENT AND
ADJUSTMENT PROCEDURE
WIRING DIAGRAM
PARTS LIST
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts
13.0 Amperes (Microwave) / 13.0 Amperes (Convection)
60 Hertz / Single phase, 3 wire grounded
Power Output
900 watts (IEC 705 Test Procedure)
Operating frequency of 2450MHz
Convection Power Output
Case Dimensions
1450 Watts
Width 24-5/8"
Height 14-7/8"
Height 9-5/8"
Depth 19-1/8"
Depth 16-1/8"
Cooking Cavity Dimensions
(1.5 Cubic Feet )
Width 16-1/8"
Control Complement
Touch Control System
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI...........................................Full power throughout the cooking time
P-90 .............................................................approx. 90% of Full Power
P-80 .............................................................approx. 80% of Full Power
P-70 .............................................................approx. 70% of Full Power
P-60 .............................................................approx. 60% of Full Power
P-50 .............................................................approx. 50% of Full Power
P-40 ..............................................................approx. 40% of Full Power
P-30 ..............................................................approx. 30% of Full Power
P-20 .............................................................approx. 20% of Full Power
P-10 ..............................................................approx. 10% of Full Power
P-0 ............................................. No power throughout the cooking time
Convection Temperature for Variable Cooking
CONVECTION.............................................. 100 - 450˚F Temp. control
LOW MIX. BAKE............................... 350˚F with 10% microwave power
HIGH MIX. ROAST ........................... 300˚F with 30% microwave power
SLOW COOK..........................................300˚F for 4 hours (no preheat)
BROIL ............................................................................ 450˚F (preheat)
CUSTOM HELP pad, SENSOR REHEAT pad, MINUTE PLUS pad, POPCORN pad
COMPU DEFROST pad, SENSOR COOK pad, COMPU BROIL pad
COMPU ROAST pad, COMPU BAKE pad, REHEAT pad, CONVEC pad
BROIL pad, SLOW COOK pad, HIGH MIX / ROAST pad, LOW MIX / BAKE pad
Number and temperature selection pads, KITCHEN TIMER pad, CLOCK pad
STOP/CLEAR pad, POWER LEVEL pad, START / TOUCH ON pad
Oven Cavity Light
Safety Standard
Yes
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the
electric current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Electrical Requirements
Grounded
Receptacle Box
The electrical requirements are a 115 -120 volt 60 Hz, AC only,
15 or 20 amp. fused electrical supply. It is recommended that a separate
circuit serving only this appliance be provided. When installing this
appliance, observe all applicable codes and ordinances.
3-Pronged Plug
A short power-supply cord is provided to reduce risks of becoming
entangled in or tripping over a longer cord.
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If an extension cord must be used, it should be a 3-wire, 15
amp. or more cord. Do not drape over a countertop or table where it can
be pulled on by children or tripped over accidentally.
Grounding Pin
3-Pronged Receptacle
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM
THIS PLUG.
OVEN DIAGRAM
TOUCH CONTROL PANEL
7
1
3
5
MIX CONV
DEFROST
SENSOR
10
9
12
COOK LBS OZ
KG HELP
CUSTOM
HELP
13
Interactive
4
8
14
15
MINUTE
PLUS
SENSOR
REHEAT
11
6
2
6
POPCORN
COMPU
7. Wave guide cover.
8. Door open button.
ELEVATE PKG
DEFROST
1. Ventilation openings. (Rear side)
2. Oven door with see-through window.
3. Oven lamp.
1 Baked potatoes
2 Frozen vegetables
3 Fresh veg-soft
4 Fresh veg-hard
5 Frozen entrees
6 Hot dogs
9. Auto-Touch control panel.
10. Lighted digital display.
11. Convection air openings.
4. Turntable support.
SENSOR
COOKT
5. Removable turntable.
The turntable will rotate clockwise or
counterclockwise.
7 Bacon
8 Fish, seafood
12. Removable low rack. (Broiling trivet)
13. Removable low rack. (Baking rack)
14. Turntable motor shaft.
Convection
6. Safety door latches.
15. Power supply cord.
The oven will not operate unless the door is
securely closed.
1 Hamburgers
COMPU
BROIL
2 Chicken pieces
3 Steaks
4 Fish steaks
1 Chicken
2 Turkey
3 Turkey breast
4 Pork
COMPU
ROAST
1 Bundt cake
2 Cookies
COMPU
BAKE
3 Muffins
4 French fries
PREHEAT CONVEC
BROIL
LOW MIX HIGH MIX
BAKE ROAST
SLOW
COOK
1 2 3 4 5
100˚F
150˚F
275˚F
300˚F 325˚F
6 7 8 9 0
350˚F
375˚F
400˚F
425˚F 150˚F
ST OP
TCLEAR
KITCHEN
TIMER
CLOCK
START
TOUCH ON
POWER
LEVEL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
Thefollowingisadescriptionofcomponentfunctionsduring
oven operation.
following results. The circuits to the turntable motor, the
cooling fan motor, and the high voltage components are
de-energized, the oven lamp remains on, and the digital
read-out displays the time still remaining in the cook
cycle when the door was opened.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
7. Themonitorswitchiselectricallymonitoringtheoperation
of theprimaryinterlockrelayandthesecondaryinterlock
switch and is mechanically associated with the door so
that it will function in the following sequence.
(1) When the door opens from a closed position, the primary
interlock relay and the secondary interlock switch open
their contacts, and then the monitor switch contacts
close.
(2) When the door is closed from the open position, the
monitor switchcontacts first open, and then the contacts
oftheprimaryinterlockrelayandthesecondaryinterlock
switch close.
If the primary interlock relay and the secondary interlock
switch fail with their contacts closed when the door is
opened, the closing of the monitor switch contacts will form
a short circuit through the monitor fuse, primary interlock
relay and the secondary interlock switch, causing the moni-
tor fuse to blow.
1. The display will show "SHARP SIMPLY THE BEST
PRESS CLEAR AND PRESS CLOCK".
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear.
NOTE: When the door is opened, the oven lamp comes on.
2. A signal is input to the control unit, energizing the coil of
shut-off relay (RY-4). RY4 contacts close, completing a
circuit to the damper motor. The damper motor now
operatesmovingthedampertotheopenposition,thereby
closingthecontactsofthe damperswitchinputsasignal
tothecontrolunit. ThecoilofrelayRY-4isde-energized,
opening its contacts, thereby turning off the damper
motor.
POWER LEVEL P-0 TO P-90 COOKING
COOKING CONDITION
When Variable Cooking Power is programmed, the 120
volts A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2). RY-2 is operated by
the control unit within an varying time base. Microwave
power operation is as follows:
Program desired cooking time Variable Cooking Control by
touchingtheNUMBERpadsandthepowerlevelpad. When
the START pad is touched, the following operations occur:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
VARI-MODE
ON TIME
32 sec.
OFF TIME
0 sec.
Power 10(P-HI)
(100% power)
RELAY
RY-1
RY-2
RY-3
RY-4
RY-5
RY-6
CONNECTED COMPONENTS
Oven lamp/Turntable motor
Power transformer
Heating element
Power 9(P-90)
30 sec.
2 sec.
(approx. 90% power)
Power 8(P-80)
(approx. 80% power)
Power 7(P-70)
26 sec.
24 sec.
6 sec.
8 sec.
Damper motor
(approx. 70% power)
Convevtion motor
Fan motor
Power 6(P-60)
(approx. 60% power)
22 sec.
18 sec.
16 sec.
12 sec.
8 sec.
10 sec.
14 sec.
16 sec.
20 sec.
24 sec.
26 sec.
32 sec.
Power 5(P-50)
(approx. 50% power)
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3 volts A.C.
output on the filament winding, and approximately 2360
volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron
filament and the H.V. winding voltage is sent to a voltage
doubler circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feed-
box, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
Power 4(P-40)
(approx. 40% power)
Power 3(P-30)
(approx. 30% power)
Power 2(P-20)
(approx. 20% power)
Power 1(P-10)
(approx. 10% power)
6 sec.
Power 0(P-0)
(0% power)
0 sec.
Note: The ON/OFF time ratio does not correspond with
the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
6. When the door is opened during a cook cycle, monitor
switch, door sensing switch, the primary interlock relay
andthesecondaryinterlockswitchareactivatedwiththe
6
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
first.Andthenprogramdesiredcookingtimebytouchingthe
Number pads. The LOW MIX/BAKE pad is preprogrammed
for 350˚F with 10% microwave power, while the HIGH MIX/
ROAST pad is preprogrammed for 300˚F with 30% micro-
wavepower. WhentheSTARTpadistouched, thefollowing
operations occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The shut-off relays (RY1,RY2,RY3,RY5 and RY6) are
energized, turning on the oven lamp, turntable motor,
cooling fan motor and convection fan motor.
3. The shut-off relay (RY4) is energized.
The damper door is closed from the open position.
4. The heater relay (RY3) is energized, applying the main
supply voltage to the heating element.
5. Now, the oven is in the convection cooking condition.
6. When the oven temperature reaches the selected
temperature, the following operations occur:
6-1. Thepowersupplyvoltageisalternatedtotheheating
element and power transformer.
CONVECTION COOKING CONDITION
PREHEATING CONDITION
Program desired convection temperature by touching the
CONVECTION pad and the Temperature pad.
When the START pad is touched, the following operations
occur:
1. The coil of shut-off relays (RY1, RY3,RY5 and RY6) are
energized, the oven lamp, cooling fan motor, turntable
motor and convection motor are turned on.
2. The coil of relay (RY4) is energized by the control unit.
Thedamperismovedtotheclosedposition, openingthe
damper switch contacts. The opening of the damper
switch contacts sends a signal to the LSI on the control
unit de-energizing the relay (RY4) and opening the
circuit to the damper motor.
3. The coil of heater relay (RY3) is energized by the control
unit and the main supply voltage is applied to the heating
element.
4. Whentheoventemperaturereachestheselectedpreheat
temperature, the following operations occur:
4-1 The heater relay is de-energized by the control unit
temperature circuit and thermistor, opening the
circuit to the heating element.
6-2. The heating element operates through the heater
relay (RY3) contacts and the power transformer
operates through the primary interlock relay (RY2)
contacts.
6-3. These are operated by the control unit to supply
alternatelywithina32secondtimebase,convection
heat and microwave energy.
4-2. The oven will continue to function for 30 minutes,
turning the heater on and off, as needed to maintain
the selected preheat temperature. The oven will
shut-down completely after 30 minutes
The relationship between the convection and microwave
power operations are as follows.
CONVECTION COOKING CONDITION
Whenthepreheattemperatureisreached,abeepsignalwill
sound indicating that the holding temperature has been
reached in the oven cavity. Open the door and place the
food to be cooked in the oven.
Touch the CONVEC pad first and then touch the Tempera-
ture pad. And program desired cooking time by touching the
Number pads.
Note: The ON and OFF time ratio does not correspond
with the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
6 SEC.
26 SEC.
ON
When the START pad is touched, the following operations
occur:
MICROWAVE POWER
= APPROX. 10%
(MICRO.)
OFF
1. The numbers on the digital read-out start to count down
to zero.
2. The oven lamp, turntable motor, cooling fan motor and
convection motor are energized.
3. Heaterrelay(RY3)isenergized(ifthecavitytemperature
is lower than the selected temperature) and the main
supply voltage is applied to the heating element to return
to the selected cooking temperature.
4. Upon completion of the cooking time, the audible signal
will sound, and oven lamp, turntable motor, cooling fan
motor and convection motor are de-energized. At the
end of the convection cycle, if the cavity air temperature
is above 275˚F, the circuit to RY6 will be maintained (by
thethermistorcircuit)tocontinueoperationofthecooling
fan motor until the temperature drops below 245˚F, at
which time the relay will be de-energized, turning off the
fan motor. Relay RY5 will however, open as soon as the
convection cycle has ended, turning off the convection
fan motor.
CONVECTION
TEMPERATUE
= 350˚F (180˚C)
(CONVEC.)
LOW MIX
BAKE
12 SEC.
20 SEC.
ON
MICROWAVE POWER
= APPROX. 30%
(MICRO.)
OFF
ON
(CONVEC.)
CONVECTION
TEMPERATUE
= 300˚F
OFF
32 SEC.
HIGH MIX
ROAST
Note: During alternate Microwave/Convection operation,
the convection heater is energized only if the cavity
temperature drops below the set temperature.
5. At the end of the convection cook cycle, shut-off relay
(RY4) is energized turning on the damper motor. The
damper is returned to the open position, closing the
damper switch contacts which send a signal to the
control unit, de-energizing shut-off relay (RY4).
SENSOR COOKING CONDITION
Using the SENSOR COOK function, the foods are cooked
withoutfiguringtime,powerlevelorquantity.Whentheoven
senses enough steam from the food, it relays the informa-
tion to its microprocessor which will calculate the remaining
cooking time and power level needed for best results.
When the food is cooked, water vapor is developed.
AUTOMATIC MIX COOKING CONDITION
Touch the HIGH MIX/ROAST or the LOW MIX/BAKE pad
7
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
The sensor “senses” the vapor and its resistance increases
gradually. When the resistance reaches the value set ac-
cording to the menu, supplementary cooking is started.
Thetimeofsupplementarycookingisdeterminedbyexperi-
ment with each food category and inputted into the LSI.
An example of how sensor works:
4. Now, the oven is in the convection cooking mode.
5. Whentheoventemperaturehasreachedtheprogrammed
convection temperature, the oven goes into the
programmed cooking mode.
6. At the end of the COMPU BROIL/ ROAST/ BAKE cycle,
the damper is returned to the open position and the oven
will go to the off condition. The cooling fan will remain on
until the oven has cooled.
1. Potatoesatroomtemperature.
Vapor is emitted very slowly.
COMPU DEFROST COOKING
The COMPU DEFROST key is a special function key to
defrost meats and poultry faster and better. COMPU DE-
FROST automatically defrosts roast beef, etc.. When the
COMPU DEFROST is selected and the food weight is
entered by using the COMPU DEFROST pad, the oven will
cook according to the special cooking sequence.
2. Heat potatoes. Moisture and
humidity is emitted rapidly.
You can smell the aroma as it
cooks.
3. Sensor detects moisture and
AH SENSOR
humidity and calculates
cooking time and variable
power.
FIRE SENSING FEATURE (MICROWAVE MODE)
This model incorporates a sensing feature which will stop
the oven's operation if there is a fire in the oven cavity during
microwave cooking.
Cooking Sequence.
This is accomplished by the LSI repeatedly measuring the
voltage across the temperature measurement circuit (ther-
mistor) during it's 32-seconds time base comparing the
obtained voltage measurements. If the most recent voltage
measured is 300mV greater than the previous voltage
measured, the LSI judges it as a fire in the oven cavity and
switches off the relays to the power transformer, fan motor
and convection motor. The LSI also stops counting down
and closes the damper door so that no fresh air will enter the
oven cavity. Please refer to the following section for a more
detailed description.
1. Touch SENSOR COOK pad.
NOTE: The oven should not be operated on SENSOR
COOK immediately after plugging in the unit. Wait
two minutes before cooking on SENSOR COOK.
2. Select desired Sensor setting.
3. Touch START pad.
The coil of shut-off relay (RY1, RY6) is energized, the
oven lamp and cooling fan motor are turned on, but the
power transformer is not turned on.
4. After about 16 seconds, the cook relay (RY-2) is
energized. The power transformer is turned on,
microwave energy is produced and first stage is started.
The 16 seconds is the cooling time required to remove
any vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
5. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero. At this time, the
door may be opened to stir food, turn it or season, etc.
6. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
7. OpeningthedoorortouchingtheSTOP/CLEARpad,the
time of day will reappear on the display and the oven will
revert to an OFF condition.
Operation
Please refer to the timing diagrams below.
1. The thermistor operates within a 32-seconds time base
and it is energized for three (3) seconds and off for 29
seconds. Two (2) seconds after the thermistor is
energized, the voltage across the temperature
measurement circuit is sampled by the LSI and twenty
one (21) seconds after the thermistor is cut off the LSI
turns on the cooling fan for six (6) seconds.
2. The above procedure is repeated. If the difference
between the first voltage measured (in step 1) and the
voltage measured when the procedure is repeated (step
2) is greater than 300mV the LSI makes the judgment
that there is a fire in the oven cavity and will switch off the
relaystothepowertransformer,fanmotorandconvection
motor. The LSI also stops counting down and closes the
damper door so that no fresh air will enter the oven
cavity.
COMPU BROIL/ COMPU ROAST/ COMPU BAKE
COMPU BROIL/ ROAST/ BAKE will automatically compute
the oven temperature, microwave power and cooking time
forbaking, roastingandbroiling. Setthedesiredprogramby
touching the COMPU BROIL/ ROAST/ BAKE pad, and
numberpad.EntertheweightbytouchingtheNumberpads.
When the START pad is touched, the following operations
occur:
3. Once the fire sensor feature has shut the unit down, the
programmedcookingcyclemayberesumedby pressing
the"START"padortheunitmayberesetbypressingthe
"CLEAR" pad.
0
2 3
24
30 32 (sec.)
64 (sec.)
6 sec.
CONVECTION
MOTOR
1. The COOK indicator will light and the Convection Fan
Symbol will rotate.
ON
OFF
3 sec.
2. The cooking time will appear on the display and start
counting down to zero. The cooking time is adjusted
automatically according to the weight of the food.
3. The shut-off relays (RY1, RY5 and RY6) are energized,
turning on the oven lamp, turntable motor, cooling fan
motor and convection motor. The power supply voltage
is applied to the heating element.
THERMISTOR
ON
OFF
ON
Sensing
Voltage
OFF
Sensing the voltage across the temperature measurement circuit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
IMPORTANT:
detected vapors and initiated a sensor cooking cycle.
This is because the operation of the convection fan
would interfere with the AH sensor's vapor detection.
During sensor cooking operation, the fire sensing op-
eration sequence will not begin until the AH sensor has
SCHEMATIC DIAGRAM
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
MAGNETRON
TEMPERATURE
FUSE
CONV.
THERMAL
CUT-OUT
FUSE
COM.
(RY1)
POWER
TRANSFORMER
A-3
A-5
A-1
TTM
FM CM DM
OL
N.O.
(RY1)
OUTER
CASE
SWITCH
CAPACITOR
0.94µ
COM.
(RY3)
A-7
A-9
RY2
COM.
(RY2)
RY2
PRIMARY
INTERLOCK
RERAY
RY3
N.O.
(RY2)
CONTROL UNIT
120V
60Hz
N.O.
(RY3)
OUTER
CASE
SWITCH
F-1
F-2
F-3
E-1 E-2 E-3 E-4 E-5 E-6
SECONDARY
INTERLOCK
SWITCH
DOOR
SENSING
SWITCH
THER-
MISTOR
DAMPER
SWITCH
AH SENSOR
Figure O-1. Oven Schematic-OFF Condition
SCHEMATIC
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. “START” PAD TOUCHED.
MAGNETRON
TEMPERATURE
FUSE
CONV.
THERMAL
CUT-OUT
FUSE
COM.
(RY1)
POWER
TRANSFORMER
A-3
A-5
A-1
TTM
FM CM DM
OL
N.O.
(RY1)
OUTER
CASE
SWITCH
CAPACITOR
0.94µ
COM.
(RY3)
A-7
A-9
RY2
COM.
(RY2)
RY2
PRIMARY
INTERLOCK
RERAY
RY3
N.O.
(RY2)
CONTROL UNIT
120V
60Hz
N.O.
(RY3)
OUTER
CASE
SWITCH
F-1
F-2
F-3
E-1 E-2 E-3 E-4 E-5 E-6
SECONDARY
INTERLOCK
SWITCH
DOOR
SENSING
SWITCH
THER-
MISTOR
DAMPER
SWITCH
AH SENSOR
Figure O-2. Oven Schematic-Microwave Cooking Condition
9
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
SCHEMATIC
1. DOOR CLOSED.
2. MIX COOKING PAD TOUCHED.
3. COOKING TIME PROGRAMMED.
4. “START” PAD TOUCHED.
5. RY2 AND RY3 WILL ALTERNATELY CLOSE.
DURING COOK CYCLE.
MAGNETRON
TEMPERATURE
FUSE
CONV.
THERMAL
CUT-OUT
FUSE
COM.
(RY1)
POWER
TRANSFORMER
A-3
A-5
A-1
TTM
FM CM DM
OL
N.O.
(RY1)
OUTER
CASE
SWITCH
CAPACITOR
0.94µ
COM.
(RY3)
A-7
A-9
RY2
COM.
(RY2)
RY2
PRIMARY
INTERLOCK
RERAY
RY3
N.O.
(RY2)
CONTROL UNIT
120V
60Hz
N.O.
(RY3)
OUTER
CASE
SWITCH
F-1
F-2
F-3
E-1 E-2 E-3 E-4 E-5 E-6
SECONDARY
INTERLOCK
SWITCH
DOOR
SENSING
SWITCH
THER-
MISTOR
DAMPER
SWITCH
AH SENSOR
Figure O-3. Oven Schematic-Automatic Mix Cooking Condition
SCHEMATIC
1. DOOR CLOSED.
2. CONVECTION PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. COOKINGTIMEPROGRAMMED.
5. “START” PAD TOUCHED.
MAGNETRON
TEMPERATURE
FUSE
CONV.
THERMAL
CUT-OUT
FUSE
COM.
(RY1)
POWER
TRANSFORMER
A-3
A-5
A-1
TTM
FM CM DM
OL
N.O.
(RY1)
OUTER
CASE
SWITCH
CAPACITOR
0.94µ
COM.
(RY3)
A-7
A-9
RY2
COM.
(RY2)
RY2
PRIMARY
INTERLOCK
RERAY
RY3
N.O.
(RY2)
CONTROL UNIT
120V
60Hz
N.O.
(RY3)
OUTER
CASE
SWITCH
F-1
F-2
F-3
E-1 E-2 E-3 E-4 E-5 E-6
SECONDARY
INTERLOCK
SWITCH
DOOR
SENSING
SWITCH
THER-
MISTOR
DAMPER
SWITCH
AH SENSOR
Figure O-4. Oven Schematic-Convection Cooking Condition
10
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR SENSING AND SECONDARY INTERLOCK
OUTER CASE SWITCHES
SWITCHES
The two outer case switches are mounted near the power
supply cord at the oven cavity rear plate. When the outer
case cabinet is installed with the screws, one of the screws
pushes the actuator and then the actuator pushes each
plungers of the two outer case switches and their contacts
are closed. When a cabinet mounting screw which is push-
ing the actuator is removed, the two outer case switches
interrupt the circuit to the all components.
The door sensing switch in the primary interlock system is
mounted in the upper position on the latch hook, the
secondary interlock switch is mounted in the lower position
on the latch hook. They are activated by the latch heads on
the door. When the door is opened, the switches interrupt
thecircuittoallcomponents. Acookcyclecannottakeplace
until the door is firmly closed thereby activating both inter-
lock switches. The primary interlock system consists of the
door sensing switch and primary interlock relay located on
the control circuit board.
WARNING
The circuit to all components can be connected to the
power supply without the outer case cabinet by reinstall-
ing the cabinet mounting screw. BUT AT THAT TIME,
NEVER TOUCH ANY PARTS OF THE HIGH VOLTAGE
CIRCUIT TO AVOID ELECTROCUTION.
DOOR SENSING
SWITCH
MONITOR FUSE
This outer case mounting screw is
pushing the actuator.
MONITOR SWITCH
SECONDARY
INTERLOCK
SWITCH
OUTER CASE
CABINET
ACTUATOR
Figure D-1. Door sensing switch, monitor switch and
secondary interlock switches
MONITOR SWITCH
OUTER CASE
SWITCHES
The monitor switch is mounted on the middle position of
latch hook. It is activated (the contacts opened) by the lower
latch head while the door is closed. The switch is intended
to render the oven inoperative by means of blowing the
monitorfusewhenthecontactsoftheprimaryinterlockrelay
and secondary interlock switch fail to open when the door is
opened.
THERMISTOR
The thermistor is a negative temperature coefficient type.
The temperature in the oven cavity is detected through the
resistance of the thermistor, and then the control unit
causes the heater relay to operate, thus the current to the
heating element is turned ON/OFF.
Functions:
1. When the door is opened, the monitor switch contact
close (to the ON condition) due to their being normally
closed. At this time the door sensing and secondary
interlock switches are in the OFF condition (contacts
open)duetotheirbeingnormallyopencontactswitches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing
switchandthesecondaryinterlockswitchcontactsclose.
(On opening the door, each of these switches operate
inversely.)
MAGNETRON TEMPERATURE FUSE.
Thetemperaturefuselocatedonthewaveguideisdesigned
to prevent damage to the magnetron if an over heated
condition develops in the megnetron due to cooling fan
failure, obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the temperature fuse remains
closed. However, when abnormally high temperatures are
reached within the magnetron, the temperature fuse will
open at 302˚F(150˚C) causing the oven to shut down.
3. If the door is opened, and the primary interlock relay and
secondary interlock switch contacts fail to open, the
monitor fuse blows simultaneously with closing of the
monitor switch contacts.
CONV. THERMAL CUT-OUT
The thermal cut-out located on the left side of the thermal
protection plate (left) is designed to prevent damage to the
heater unit if an over heated condition develops in the
heating unit due to convection fan failure, thermistor failure,
obstructed air ducts, dirty or blocked air intake, etc.
Undernormaloperation,thethermalcut-outremainsclosed.
However, when abnormally high temperatures are reached
within the heater unit, the thermal cut-out will open at
302˚F(150˚C) causing the oven to shut down.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE TEST THE DOOR SENSING SWITCH,
PRIMARYINTERLOCKRELAY,SECONDARY
INTERLOCK SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION. (RE-
FER TO CHAPTER “TEST PROCEDURE”).
When the thermal cut-out has cooled, the thermal cut-out
closes at 266˚F(130˚C).
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Damper is in the closed position, so that no hot air will be
allowed to leak out the oven cavity.
HEATING ELEMENT
The heating element is located at the left side of the oven
cavity. It is intended to heat air driven by the convection fan.
The heated air is kept in the oven and force-circulated and
reheated by the heating element.
Damper Operation
1. When power supply cord is plugged in:
1-1. When power supply cord is plugged in, a signal is
sensed in the control unit, and operates shut-off
relay (RY4).
CONVECTION COOKING SYSTEM
This oven is designed with a hot air heating system where
food is not directly heated by the heating element, but is
heated by forced circulation of the hot air produced by the
heating element.
The air heated by the heating element is circulated through
the convection passage provided on the outer casing of the
oven cavity by means of the convection fan which is driven
bytheconvectionmotor. Itthenenterstheinsideoftheoven
through the vent holes provided on the left side of the oven.
Next, the hot air heats the food on the turntable and leaves
the oven cavity through the vent in the center of the oven
cavity left side wall.
1-2. Contacts of shut-off relay (RY4) close, the damper
motor is energized, opening the damper door.
1-3. When the damper is moved to the open position by
the damper cam the damper switch is closed (ON
position).
1-4. The signal from damper switch is re-sensed in the
control unit and shut-off relay (RY4) is turned off.
1-5. The 120 volts A.C. to the damper motor is removed
and the motor turns off.
2. When oven is microwave cooking:
Damper is in the open position.
3. When oven is convection cooking:
Without leaving the oven, this hot air is reheated by the
heating element, passes through the convection passage
and enters the inside of the oven cavity again, in a continu-
ing cycle.
In this way, the hot air circulates inside the oven cavity to
raise its temperature and, at the same time, comes into
contact with the food being cooked.
3-1. Damper motor is energized by touching the
convection, temperature and START pads.
3-2. When damper is in the closed position (damper
switch is OFF), its signal is sensed by the control
unit, and shut-off relay (RY4) is de-energized.
3-3. The damper is held in the closed position during the
convection cooking operation.
When the temperature inside the oven cavity reaches the
selected temperature, the heating element is de-energized.
When the temperature inside the oven cavity drops below
the selected temperature, the heating element is energized
again. Inthisway, theinsideoftheovencavityismaintained
at approximately the selected temperature.
When the convection time reaches 0, the heating element is
de-energized and the convection fan stops operating and
the oven shuts off.
3-4. At the end of the convection cooking, shut-off relay
(RY4) is energized, and the damper is returned to
the open position.
NOTE: If the damper door is not in the proper position,
closedduringconvectionoropenduringmicrowave,
the control unit will stop oven operation after 1
minute.
DAMPER OPEN-CLOSE MECHANISM
DAMPER SHAFT
Usually, the damper is in the open position except during
convectioncooking. Damperpositionissetautomaticallyby
damper motor, damper switch, motor cam and damper
shaft. These components are operated by a signal that
judges if microwave cooking or convection cooking opera-
tion is selected by the control unit.
DAMPER DUCT
DAMPER
Microwave Cooking:
DAMPER CAM
Damper is in the open position, because a portion of cooling
air is channelled through the cavity to remove steam and
vapors given off from the heating foods.
It is then exhausted at the top of the oven cavity into a
condensation compartment.
DAMPER SWITCH
DAMPER MOTOR
Convection Cooking:
Figure D-2. Damper Mechanism
TROUBLESHOOTING GUIDE
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the “Test Procedure”section.
IMPORTANT: Iftheovenbecomesinoperativebecauseofablownmonitorfuse, checkthemonitorswitch, primaryinterlock
relay, door sensing switch and secondary interlock switch before replacing the monitor fuse. If monitor fuse
is replaced, the mintor switch must olso be replaced at the same time. Use part FFS-BA012WRK0 as an
assembly.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
(SENSOR
COOKING)
CONDITION
COOKING CONDITION
OFF CONDITION
(MICROWAVE)
(CONVECTION)
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
A
B
C
D
E
F
G
H
I
MAGNETRON
POWER TRANSFORMER
H.V. RECTIFIER ASSEMBLY
HIGH VOLTAGE CAPACITOR
SECONDARY INTERLOCK SWITCH
PRIMARY INTERLOCK SYSTEM
MONITOR SWITCH
MONITOR FUSE
MAGNETRON TEMPERATURE FUSE
CONV. THERMAL CUT-OUT
CONVECTION HEATER
THERMISTOR
J
K
L
M
N
P
Q
R
S
S
S
S
S
S
U
V
DAMPER MOTOR
DAMPER SWITCH
OUTER CASE SWITCH
TOUCH CONTROL PANEL
KEY UNIT
RELAY RY-1
RELAY RY-2
RELAY RY-3
RELAY RY-4
RELAY RY-5
RELAY RY-6
FOIL PATERN ON PWB.
AH SENSOR
Replace OVEN LAMP OR SOCKET
Replace FAN MOTOR
Replace TURNTABLE MOTOR
Replace CONVECTION MOTOR
Check
Check
Check
Check
LOOSE WIRING
SHORTED IN POWER CORD
NO POWER AT OUTLET
LOW VOLTAGE
13
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
A
MAGNETRON ASSEMBLY TEST
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
Totestforanopenfilament,isolatethemagnetronfromthehighvoltagecircuit.Acontinuitycheckacross
the magnetron filament leads should indicate less than 1 ohm.
Totestforashortedmagnetron, connecttheohmmeterleadsbetweenthemagnetronfilamentleadsand
chassis ground. This test should indicate an infinite resistance. If there is little or no resistance the
magnetron is grounded and must be replaced.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
shouldonlybeusedifabovetestsdonotindicateafaultymagnetronandthereisnodefectinthefollowing
componentsorwiring:siliconrectifier,highvoltagecapacitorandpowertransformer.Thistestwillrequire
a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with
a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through
the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER HI(HIGH) selecting more than 60
secondscooktime. Allowthewatertoheatfor60seconds, measuringwithastopwatch, secondhand
of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 22
to 43˚F(12.2 to 23.8˚C) rise in temperature. If the water temperatures are accurately measured and
tested for the required time period the test results will indicate if the magnetron tube has low power
output (low rise in water temperature) which would extend cooking time or high power output (high
rise in water temperature) which would reduce cooking time. Because cooking time can be adjusted
to compensate for power output, the magnetron tube assembly should be replaced only if the water
temperature rise test indicates a power output well beyond the normal limits. The test is only accurate
if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
Disconnecttheprimaryinputterminalsandmeasuretheresistanceofthetransformerwithanohmmeter.
Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary coil
shouldbelessthan1ohmandtheresistanceofthehighvoltagecoilshouldbeapproximately84.4ohms;
the resistance of the filament coil should be less than 1 ohm.
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance across
the terminals and observe, reverse the leads to the rectifier terminals and observe meter reading. If a
short is indicated in both directions, or if an infinite resistance is read in both directions, the rectifier is
probably defective and should be replaced.
D
HIGH VOLTAGE CAPACITOR TEST
DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS
OR WIRING.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and
check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity
for a short time and should indicate approximately 10 MΩ once the capacitor is charged. If the above is
not the case, check the capacitor with an ohmmeter to see if it is shorted between either of the terminals
and case. If it is shorted, replace the capacitor.
E
F
SECONDARY INTERLOCK SWITCH TEST
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicated an open circuit with the door open and a closed circuit with the
door closed. If improper operation is indicated, replace the secondary interlock switch.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch, the meter should indicated an open circuit with the door open and a closed circuit with the
door closed. If improper operation is indicated, replace the door sensing switch.
PRIMARY INTERLOCK RELAY
Disconnect two (2) wire leads from the common (COM.) and normally open (NO) terminal of the primary
Interlock relay (RY2). Check the state of the relay contacts using a ohmmeter. The relay contacts should
be open. If the relay contacts are closed, replace the relay itself.
G
MONITOR SWITCH
Disconnect the oven from power supply.
Before performing this test, make sure that the secondary interlock switch and the primary interlock relay
are operating properly, according to the above Test Procedures. Disconnect the wire lead from the
monitor switch (NC) terminal. Check the monitor switch operation by using the ohmmeter as follows.
When the door is open, the meter should indicate a closed circuit. When the monitor switch actuator is
pushed by a screw driver through the lower latch hole on the front plate of the oven cavity with the door
opened(inthisconditiontheplungerof
the monitor switch is pushed in), the
meter should indicate an open circuit.
N.C.
MONITOR SWITCH
If improper operation is indicated, the
switch may be defective. After testing
COM.
themonitorswitch, re-connectthewire
SCREW DRIVER
lead to the monitor switch (NC) termi-
nal and check for continuity of monitor
circuit.
SECONDARY
INTERLOCK
SWITCH
OHMMETER
H
BLOWN MONITOR FUSE
If the monitor fuse is blown when the door is opened, check the primary interlock relay, secondary
interlock switch, door sensing switch and monitor switch according to the "TEST PROCEDURE" for
those switches before replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK
RELAY, SECONDARYINTERLOCKSWITCH, DOORSENSINGSWITCHANDMONITOR
SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and switch must be replaced
with "monitor fuse and switch assembly" part number FFS-BA012WRK0, even if the monitor switch
operates normally. The monitor fuse and switch assembly is packed with 20 ampere fuse and switch.
I
TEMPERATURE FUSE TEST
A continuity check across the temperature fuse terminals should indicate a closed circuit unless the
temperature of the magnetron reaches approximately 302˚F (150˚C). If the temperature fuse has
opened, replace the temperature fuse.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
Anopentemperaturefuseindicatesoverheatingofthemagnetronassembly, checkforrestrictedairflow
to the magnetron through the opening in the chassis, especially the cooling duct and cooling fan.
J
THERMAL CUT-OUT TEST
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of thermal cut-out reaches 302˚F(150˚C). The thermal cut-out resets automatically at
approximately 266˚F(130˚C). If the thermal cut-out has opened under the normal condition,
replace the same item as in the parts list. An open thermal cut-out indicates overheating of heater
unit.
Check for restricted air flow to the heater unit through the vent hole of the oven cavity, especially the
heater duct and convection fan.
K
HEATING ELEMENT TEST
Make sure the heating element is fully cooled and test as follows;
a. Disconnect wire leads and measure the resistance with an ohmmeter. On the R x 1 scale, the
resistance between the heating element terminals should be approximately 10.2Ω.
b. Disconnect wire leads and measure the insulation resistance with 500V - 100MΩ insulation
resistance meter. The insulation resistance between heating element terminal and cavity should be
more than 0.5MΩ.
L
THERMISTOR TEST
Disconnect connector-E from the control unit. Measure the resistance of the thermistor with an
ohmmeter. Connect the ohmmeter leads to Pin No’s E-3 and E-4.
Room Temperature
Resistance
68˚F(20˚C) - 86˚F(30˚C)
Approx. 350kΩ - 155KΩ
If the meter does not indicate above resistance, replace the thermistor
M
DAMPER MOTOR TEST
When the power cord is plugged into the wall receptacle and 120 volts A.C. is supplied to the damper
motor, the motor operates until the damper is opened and the damper switch closes. Then the damper
motor stops operation.
If the damper motor does not operate, check for A.C. voltage with a voltmeter at the motor.
1. Disconnect the power cord from the wall receptacle.
2. Disconnectthewireleadsofmotorandconnectthemeterleadstothewireleadsofmainwireharness.
3. Re-connect the power cord into the wall receptacle.
If 120 volts A.C. is indicated at the wire leads, replace the motor and if 120 volts A.C. is not indicated,
check the wire harness and control unit.
N
DAMPER SWITCH TEST
Disconnectthewireleadsfromtheswitchterminalsandconnectohmmeterleadstothecommon(COM.)
and normally open (N.O.) terminals of the switch.
1. When switch actuator is pushed by the damper motor cam, the meter should be indicated a closed
circuit.
2. When power cord is plugged into the wall receptacle, the damper motor operates and damper cam
willstarttorotate. Whentheswitchactuatorisreleased, themetershouldbeindicatedanopencircuit.
If improper operation is indicated, replace the damper switch.
O
CHECKING TEMPERATURE IN THE CONVECTION MODE
It is difficult to measure the exact temperature in the convection oven. An accurate thermocouple type
temperature tester must be used. A low priced bi-metal type thermometer is not reliable or accurate.
The temperature should be checked with outer case cabinet installed, approx. 5 minutes after preheat
16
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
temperature is reached (audible signal sounds four times). The temperature experienced may be
approx. 30˚F more or less than indicated on the display, however, in most cases the food cooking results
will be satisfactory.
Difference in power supply voltage will also affect the oven temperature. The Household power supply
voltage may sometimes become lower than the rated voltage (120 V) and cause under-cooking. If the
powersupplyvoltageis10%lowerthantheratedvoltage, longercookingtimeisrequiredby10%to20%.
P
OUTER CASE SWITCH TEST
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicated an open circuit when its plunger is release, and a closed circuit
when its plunger is pushed. If improper operation is indicated, replace the outer case switch.
Q
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit and troubleshooting by unit replacement is described according to the symptoms indicated.
1. Key Unit. Note : Check key unit ribbon connection before replacement.
The following symptoms indicate a defective key unit. Replace the key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
2. Control Unit
The following symptoms indicate a defective control unit. Replace the control unit.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) All digits in the figure flicker.
2-3 Other possible troubles caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
d) Proper temperature measurement is not obtained.
Note: When defective components, the Control Unit or Key Unit are replaced, the defective part or parts
must be properly packed for return in the shipping carton, with its cushion material, in which the
new replacement part was shipped to you.
R
KEY UNIT TEST
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable is
making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
Ifthecontrolunitrespondsbyclearingwithabeepthekeyunitisfaultyandmustbereplaced.Ifthecontrol
unit does not respond, it is a faulty and must be replaced. If a specific pad does not respond, the above
method may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
G 5
G 6
G 7
G 8
G 9
G10
G11
G12
HIGH MIX
ROAST
MINUTE
PLUS
SENSOR COMPU COMPU COMPU
COMPU
DEFROST
BROIL
G 4
G 3
G 2
G 1
COOK
BROIL
ROAST
BAKE
1
100˚F
2
150˚F
3
275˚F
4
300˚F
5
325˚F
POPCORN
PREHEAT CONVEC
SENSOR SLOW LOW MIX
REHEAT
6
350˚F
7
375˚C
8
400˚F
9
425˚F
0
450˚F
COOK
BAKE
START
TOUCH ON
CUSTOM
HELP
KITCHEN POWER
TIMER LEVEL
STOP
CLEAR
CLOCK
S
RELAY TEST
Remove the outer case and check voltage between Pin Nos. 7 and 9 of the 9- pin connector (A) on the
control unit an A.C. voltmeter. The meter should indicate 120 volts, if not check the oven circuitry.
Shut-off, Cook and Heater Relay Test
These relays are operated by D.C. voltage
CheckvoltageattherelaycoilwithaD.C. voltmeterduringthemicrowavecookingoperationorconvection
cooking operation.
DC. voltage indicated ............. Defective relay.
DC. voltage not indicated ........ Check diode which is connected to the relay coil. If diode is good, control
unit is defective.
RELAY SYMBOL
RY1
OPERATIONAL VOLTAGE
Approx. 19.0V D.C.
Approx. 18.0V D.C.
Approx. 18.0V D.C.
Approx. 19.0V D.C.
Approx. 19.0V D.C.
CONNECTED COMPONENTS
Oven lamp / Turntable motor
RY2(COOK)
RY3(HEATER)
RY4
Power transformer
Heating element
Damper motor
RY5
Convection motor
RY6
Approx. 19.0V D.C.
Cooling fan motor
T
COMPU DEFROST TEST
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the "COMPU DEFROST" pad twice and touch the Number pad "5". And then touch
the "START" pad.
(3) After 2 sec. Now the oven is in COMPU DEFROST cooking condition.
(4) The oven will operate as follows.
WEIGHT
1ST STAGE
2ND STAGE
LEVEL TIME LEVEL TIME
0% 52sec. 50% 32sec.
3RD STAGE
4TH STAGE
LEVEL TIME
30% 40sec.
LEVEL TIME
0.5lbs
70%
47sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
U
PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD
(PWB) IS OPEN.
o protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on
the PWB, this foil pattern acts as a fuse. If the foil pattern is open, follow the troubleshooting guide
given below for repair.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
Problem: POWER ON, indicator does not light up.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
The rated voltage is not applied to POWER
terminal of CPU connector (CN-A).
The rated voltage is applied to primary side
of power transformer.
Check supply voltage and oven power cord.
2
3
4
Power transformer or secondary circuit defective.
Check and repair.
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
NOTE: *At the time of making these repairs, make a
visual inspection of the varistor. Check for
burneddamageandexaminethetransformer
with an ohmmeter for the presence of layer
short-circuit (check the primary coil resist-
ance which is approximately 175Ω ± 10%). If
any abnormal condition is detected, replace
the defective parts.
d
b
a
c
V
AH SENSOR TEST
Checking the initial sensor cooking condition
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95˚F (35˚C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the "INSTALLATION
Instructions".
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5)Besuretheexteriorofthecookingcontainerandtheinterioroftheovenaredry. Wipeoffanymoisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapour given of by the spray and turn off before food is properly cooked.
(8) After 30 minutes if the sensor has not detected the vapour of the food, ERROR will appear and the
oven will shut off.
Water load cooking test
Make sure the oven has been plugged in at least five minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch SENSOR COOK pad and number pad 1. Now, the oven is in the sensor cooking condition and
"BAKED POTATO" will appear in the display.
(5)TouchStartpad. Theovenwilloperateforthefirst16seconds, withoutgeneratingmicrowaveenergy.
WhentheAHsensorisdefective(openorshort),Errorwillappearinthedisplayafter16secondscleaning
time.
If ERROR appears check sensor wire connections and/or AH sensor.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TEST PROCEDURES
COMPONENT TEST
PROCEDURE
LETTER
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced, and the display should start to count
down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect oven from power supply and remove outer case.
(2) Discharge the high voltage capacitor.
(3) Remove the AH sensor.
(4) Install the new AH sensor.
(5) Re-install the outer case.
(6) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
6-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
6-2. Place the container on the center of tray in the oven cavity.
6-3. Close the door.
6-4. Touch SENSOR COOK pad and number 1 pad.
6-5. Touch Start pad. The control panel is in automatic Sensor operation.
6-6. The display will start to count down the remaining cooking time, and the oven will turn off
automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit.
CHECKING CONTROL UNIT
(1) Disconnect oven from power supply and remove outer case.
(2) Discharge the high voltage capacitor.
(3) Disconnect the wire leads from the cook relay.
(4) Disconnect the sensor connector that is mounted to lower portion of control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
6-1. Touch SENSOR COOK pad and number 1 pad.
6-2. Touch Start pad. The control panel is in the sensor cooking operation.
6-3. After approximately 20 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
6-4. After approximately 3 seconds, the display shows " X X . X X " which is the remaining cooking
time, and the display count down.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
Plunger
NC
R1,R2 : 22Ω ± 1% 1/2W
NO
R3 : 4.3kΩ ± 5% 1/4W
To connector (F)
on Control Unit.
R4 : 1MΩ ± 5% 1/4W
COM
1
NO
NC
F-1
F-2
COM
2
3
R1
R2
F-3
R3
R4
CONNECTOR
Sensor Dummy Resistor Circuit
20
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units
as shown in the touch control panel circuit.
4) ACL Circuit
A circuit to generate a signals which resetting the LSI to
the initial state when power is applied.
(1) Key Unit
(2) Control Unit
5) Buzzer Circuit
The buzzer is responds to signals from the LSI to emit
noticingsounds(keytouchsoundandcompletionsound).
The principal functions of these units and the signals
communicated among them are explained below.
6) Temperature Measurement Circuit : (OVEN
THERMISTOR)
Key Unit
The key unit is composed of a matrix, signals P10 - P17
generated in the LSI are sent to the key unit.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through R24 - R27
to perform the function that was requested.
The temperature in the oven cavity is sensed by the
thermistor.Thevariationofresistanceaccordingtosensed
temperatureisdetectedbythetemperaturemeasurement
circuit and the result applied to LSI. The LSI uses this
information to control the relay and display units.
Control Unit
7) Absolute Humidity Sensor Circuit
Control unit consists of LSI, power source circuit, synchro-
nizingsignalcircuit,ACLcircuit,buzzercircuit,temperature
measurement circuit, absolute humidity sensor circuit and
indicator circuit.
This circuit detects the humidity of a food which is being
cooked, to control its automatic cooking.
8) Door Sensing Switch
A switch to inform the LSI if the door is open or closed.
1) LSI
This LSI controls the temperature measurement signal,
AH sensor signal, key strobe signal, relay driving signal
for oven function and indicator signal.
9) Relay Circuit
To drive the magnetron, heating element, fan motor,
convection motor, damper motor, turntable motor and
light the oven lamp.
2) Power Source Circuit
This circuit generates the voltages necessary for the
control unit from the AC line voltage.
10) Indicator Circuit
Indicator element is a Fluorescent Display.
Basically,aFluorescentDisplayistriodehavingacathode,
agridandananode.Usually,thecathodeofaFluorescent
Display is directly heated and the filament serves as
cathode.
The Fluorescent Display has 8-digits, 16-segments are
used for displaying figures.
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit. It incorporates a very small error because it
works on commercial frequency.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
DESCRIPTION OF LSI
LSI(IZA797DR):
The I/O signals of the LSI(IZA797DR) are detailed in the following table.
Pin No.
Signal
VCC
I/O
IN
Description
1
2
Connected to GND.
VEE
IN
Anode (segment) of Fluorescent Display light-up voltage: -30V.
Vp voltage of power source circuit input.
3
AVSS
IN
Power source voltage: -5V.
VC voltage of power source circuit input.
4
5
VREF
AN7
IN
IN
Reference voltage input terminal.
A reference voltage applied to the A/D converter in the LSI. Connected to GND.(0V)
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is
an analog input terminal from the AH sensor circuit, and connected to the A/D
converter built into the LSI.
6
AN6
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the
A/D converter built into the LSI.
7-9
10
AN5-AN3
AN2
IN
IN
Heating constant compensation terminal.
Input signal which communicates the door open/close information to LSI.
Door closed; "H" level signal(0V).
Door opened; "L" level signal(-5V).
11
AN1
IN
Input signal which communicates the damper open/close information to LSI.
Damper opened; "H" level signal(0V:GND).
Damper closed; "L" level signal(-5V).
12
13
AN0
P55
IN
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the thermistor,
this input is converted into temperature by the A/D converter built into the LSI.
OUT
Digit selection signal.
The relationship between digit signal and digit are as follows;
H
Digit signal
Digit
ß(60Hz)
L
P03........................... 1st.
P02.......................... 2nd.
P01........................... 3rd.
P00........................... 4th.
P37........................... 5th.
P36.......................... 6th.
P35.......................... 7th.
GND
VP
P03
P02
P01
P00
P37
P36
P55.......................... 8th.
Normally, one pulse is output in every ß
period, and input to the grid of the Fluores-
cent Display.
P35
P55
14
P54
OUT
Oven lamp and turntable motor driving signal. (Square Waveform : 60Hz)
16.7 msec.
To turn on and off the shut-off relay(RY1).
H
The square waveform voltage is delivered to
L
the relay(RY1) driving circuit.
During cooking
15
16
P53
P52
OUT
OUT
Convection motor driving signal.
H.
L
GND
During
cooking
OFF
To turn on and off shut-off relay(RY5). "L"
level during CONVECTION; "H" level other-
wise.
(Convection)
ON
ON
Cooling fan motor driving signal.
To turn on and off shut-off relay(RY6). "L"
level during both microwave and convection
cooking; "H" level otherwise.
H. GND
L
OFF
During
cooking
22
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Pin No.
Signal
I/O
Description
17
P51
OUT
Magnetron high-voltage circuit driving VARI MODE
ON TIME
OFF TIME
P-HI (100% power)
32 sec.
30 sec.
26 sec.
24 sec.
22 sec.
18 sec.
16 sec.
12 sec.
8 sec.
0 sec.
2 sec.
signal.
P-90 (approx. 90% power)
To turn on and off the cook relay(RY2). In
P-HI operation, the signals holds "L" level
during microwave cooking and "H" level
while not cooking. In other cooking modes
(P-90, P-80, P-70, P-60, P-60, P-50, P-40,
P-30, P-20, P-10, P-0) the signal turns to
"H" level and "L" level in repetition accord-
ing to the power level.
P-80 (approx. 80% power)
P-70 (approx. 70% power)
P-60 (approx. 60% power)
P-50 (approx. 50% power)
P-40 (approx. 40% power)
P-30 (approx. 30% power)
P-20 (approx. 20% power)
P-10 (approx. 10% power)
P-0 (0% power)
6 sec.
8 sec.
10 sec.
14 sec.
16 sec.
20 sec.
24 sec.
26 sec.
32 sec.
6 sec.
0 sec.
18
19
P50
P47
OUT
OUT
Damper motor relay driving signal.
H : GND
L
OFF
To turn on and off shut-off relay(RY4).
ON
Heating element driving signal.
Toturnonandoffshut-offrelay(RY3)."L"levelduring
convection cooking; "H" level otherwise. During con-
vection cooking, the signal becomes "H" level when
the temperature of the oven cavity exceeds the
predetermined temperature.
H.
L
GND
During
OFF
cooking
(Convection)
ON
20-21
22
P46-P45
P44
OUT
OUT
Terminal not used.
Timing signal output terminal for temperature measurement(OVEN THERMIS-
TOR).
"H" level (GND) : Thermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
0.1 sec
23
P43
OUT
Signal to sound buzzer.
A
A: key touch sound.
2.0 sec
B: Completion sound.
C:Whenthetemperatureoftheovencavity
B
reaches the preset temperature in the
preheatingmode,orwhenthepreheating
hold time (30 minutes) is elapsed.
1.0 sec
1.0 sec
H: GND
L
C
24
25
P42
OUT
IN
Timing signal output terminal for temperature measurement(OVEN).
"H" level (GND) : Ttermistor OPEN timing.
"L" level (-5V) : Temperature measuring timing.(Convection cooking)
Signal to synchronize LSI with commercial power source freqency.
INT1
H : GND
L (-5V)
This is the basic timing for all real time
processing of LSI.
16.7 msec.
26
27
P40
IN
IN
Connected to GND.
RST
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to "L" level the moment power is applied, at this time the LSI is reset. Thereafter
set at "H" level.
28/29
30
XCIN/XCOUT
OUT
IN
Terminal not used.
XIN
Internal clock oscillation frequency setting input.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to XOUT terminal.
31
32
33
XOUT
VSS
P27
OUT
IN
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Power source voltage: -5V.
VC voltage of power source circuit input.
IN
Signal coming from touch key.
When any one of G-1 line keys on key matrix is touched, a corresponding signal from
P17 - P17 will be input into P27. When no key is touched, the signal is held at "L" level.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Pin No.
Signal
I/O
Description
34
35
36
P26
IN
Signal similar to P27.
When any one of G-2 line key on key matrix is touched, a corresponding signal will be
input into P26.
P25
P24
IN
IN
Signal similar to P27.
When any one of G-3 line key on key matrix is touched, a corresponding signal will be
input into P25.
Signal similar to P27.
When any one of G-4 line key on key matrix is touched, a corresponding signal will be
input into P24.
37
P23
OUT
Segment data signals.
The relation between signals and indicators are as follows:
Signal Segment Signal Segment Signal Segment Signal Segment
P23............. P1 P17 ............. P5 P13 .............P9 P07 ........... P13
P22............. P2 P16 ............. P6 P12 ...........P10 P06 ........... P14
P21............. P3 P15 ............. P7 P11 ...........P11 P05 ........... P15
P20............. P4 P14 ............. P8 P10 ...........P12 P04 ........... P16
38-40
41
P22-P20
P17
OUT
OUT
Segment data signal.
Signal similar to P23.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse
signal is input to P24-P27 terminal while one
of G-12 line keys on key matrix is touched.
42
43
44
45
46
47
P16
P15
P14
P13
P12
P11
OUT
OUT
OUT
OUT
OUT
OUT
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-11 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-10 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-9 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-8 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-7 line keys on key matrix is touched.
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-6 line keys on key matrix is touched.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Pin No.
Signal
I/O
Description
48
P10
OUT
Segment data signal.
Signal similar to P23.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P24-P27 terminal while
one of G-5 line keys on key matrix is touched.
49-53
54-56
57-59
P07-P03
P02-P00
P37-P35
OUT
OUT
OUT
Segment data signal.
Signal similar to P23.
Digit selection signal.
Signal similar to P55.
Digit selection signal.
Signal similar to P55.
60-64
P34-P30
OUT
Used for initial balancing of the bridge circuit (absolute humidity sensor).
ABSOLUTE HUMIDITY SENSOR CIRCUIT
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AN6 terminal.
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R50-1. Changing the
resistance values results in that there is the same
potential at both F-3 terminal of the absolute humidity
sensor and AN7 terminal of the LSI. The voltage of AN6
terminal will indicate about -2.5V. This initial balancing
is set up about 16 seconds after the unit is put in the
SensorCookingmode. Asthesensorcookingproceeds,
the food is heated to generate moisture by which the
resistance balance of the bridge circuit is deviated to
increasethevoltageavailableatAN6terminaloftheLSI.
Then the LSI observes that voltage at AN6 terminal and
comparesitwithitsinitialvalue,andwhenthecomparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation
automatically.
Sensing part
Sensing part
(Closed vessel)
(Open vessel)
Sensing part
(Open vessel)
Thermistor
Thermistor
element
element
Ventilation
openings
Sensor
case
Sensing part
(Closed vessel)
View of sensor case removed
Cross section view
(2) Operational Principle of Absolute Humidity Sensor
Thefigurebelowshowsthebasicstructureofanabsolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
When the LSI starts to detect the initial voltage at AN6
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance, of
the bridge circuit due to disconnection of the absolute
humidity sensor, ERROR will appear on the display and
the cooking is stopped.
Each thermistor is supplied with a current to keep it
heated at about 150˚C (302˚F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different
degrees of heat conductivity leading to a potential
differencebetweenthemcausinganoutputvoltagefrom
the bridge circuit, the intensity of which is increased as
the absolute humidity of the air increases. Since the
output is very minute, it is amplified by the operational
amplifier.
1) Absolute humidity sensor circuit
IC2(IZA495DR)
SW1
64
63
4
5
6
7
8
P30
P31
P32
P33
P34
620k
SW2
SW3
SW4
SW5
300k
150k
75k
62
61
60
Absolute humidity vs,
output voltage characterist
Operational
amplifier
C
R1
R2
C. Thermistor in
closed vesssl
S. Thermistor in
open vessel
Output
voltage
37.4k
+
-
5
3
AN7
S
47k
S : Thermistor
open vessel
C : Thermistor
closed vessel
LSI
(IC1)
11
F-1
C
R3
F-3
Absolute humidity (g/m2)
3.57k
+
10k
6
2
AN6
(3) DetectorCircuitofAbsoluteHumiditySensorCircuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
-
47k
S
3.32k
1.8k
F-2
360k
10
9
1
12
VA : -15V
VA : -15V
VC : -5V
25
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
SERVICING
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremelyhighimpedanceatitsinputandoutputterminals.
For this reason, it is easily influenced by the surrounding
high voltage power source, static electricity charge in
clothes, etc, and sometimes it is not fully protected by the
built-in protection circuit.
while keeping it connected to the oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, therefore, it is possible to check and repair the
controls of the touch control panel while keeping it apart
from the oven proper; in this case you must short both
ends of the door sensing switch (on PWB) of the touch
control panel with a jumper, which brings about an
operationalstatethatisequivalenttotheovendoorbeing
closed. As for the sensor-related controls of the touch
control panel, checking them is possible if dummy
resistor(s)withresistanceequaltothatofthecontrolsare
used.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper,and short both ends of the door sensing
switch (on PWB) of the touch control panel,which brings
about an operational state that is equivalent to the oven
door being closed. Connect an external power source to
the power input terminal of the touch control panel, then
it is possible to check and repair the controls of the touch
control panel it is also possible to check the sensor-
related controls of the touch control panel by using the
dummy resistor(s).
approx. 1M ohm
2. Shapes of Electronic Components
Transistor
B
C
DTA123ES
KRA101M
KRA223M
KRC243M
E
4. Servicing Tools
Toolsrequiredtoservicethetouchcontrolpanelassembly.
1) Soldering iron: 30W
(Itisrecommendedtouseasolderingironwithagrounding
terminal.)
2) Oscilloscope:Singlebeam,frequencyrange:DC-10MHz
type or more advanced model.
Transistor
2SB910M
B
C
E
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
theservicing,powertothetouchcontrolpanelisavailable
either from the power line of the oven itself or from an
external power source.
3) Others: Hand tools
5. Other Precautions
(1) Servicing the touch control panel with power supply
of the oven:
1) Before turning on the power source of the control unit,
remove the aluminum foil applied for preventing static
electricity.
CAUTION:
2) Connect the connector of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminum foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Besuretousespecifiedcomponentswherehighprecision
is required.
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING PRESENTS A HAZARD.
Therefore, when checking the performance of the touch
control panel, put the outer cabinet on the oven to avoid
touching the high voltage transformer, or unplug the
primary terminal (connector) of the high voltage
transformer to turn it off; the end of such connector must
be insulated with an insulating tape. After servicing, be
sure to replace the leads to their original locations.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can't be separated.
For those models, check and repair all the controls
(sensor-related ones included) of the touch control panel
26
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
CAUTION: DISCONNECT OVEN FROM POWER SUPPLY BEFORE REMOVING OUTER CASE.
DISCHARGE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN COMPONENTS OR WIRING
AFTER REMOVING OUTER CASE.
WARNING FOR WIRING
3) Sharp edge:
To prevent an electric shock, take the following man-
ners.
1. Before wiring,
Bottom plate, Oven cavity, Weveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
1) Disconnect the power supply.
2) Open the door and wedge the door open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector certainly until its pin
islocked. Andmakesurethatthewireleadsshouldnot
come off even if the wire leads is pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
2. Don’t let the wire leads touch to the followiong parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
OUTER CASE REMOVAL
To remove the components, procedure as follows.
1. Disconnect oven from power supply.
2. Remove screws from rear and along the side edge of
case.
it from retaining clips on the cavity face plate.
4. Lift entire case from the unit.
CAUTION: DISCONNECT OVEN FROM POWER SUP-
PLY BEFORE REMOVING OUTER CASE.
3. Slide the entire case back out about 1 inch (3 cm) to free
OUTER CASE SWITCHES REPLACEMENT
Removal
3. Re-connect the wire leads to the outer case switches,
referring to the Pictorial diagram.
4. Re-install the one (1) snap of the main wire harness to
the hole of the switch holder.
5. Catch the one (1) tab of the switch holder to the one (1)
hole of the oven cavity rear plate.
1. Disconnect the oven from the power supply and remove
the outer case.
2. Discharge high voltage capacitor.
3. Remove the one (1) screw holding the switch holder to
the oven cavity rear plate.
4. Release the one (1) tab of the switch holder from the one
(1) hole of the oven cavity plate.
5. Disconnect the wire leads from the outer case switches.
6. Remove the switch holder (outer case switch assembly)
from the oven cavity rear plate.
6. Re-installtheswitchholder(outercaseswitchassembly)
to the oven cavity rear plate with the one (1) screw.
7. Re-installtheoutercasecabinetandcheckthattheoven
is operating properly.
Outer case
switch
7. Push on the one (1) retaining tab holding the outer case
switch.
8. Turn the outer case switch clockwise around the pole.
9. Now, the outer case switch is free.
NOTE: Donotlosetheactuatorbecauseitwillbelooseafter
the outer case switches are removed.
Re-install
Actuator
Switch
holder
1. Re-install the actuator to the switch holder by inserting
the tab of the actuator into the square hole on the switch
holder, as shown in Figure C-1.
2. Re-install the outer case switches to the switch holder,
as shown in Figure C-1.
Outer case
switch
Figure C-1. Outer case switches replacement
POWER TRANSFORMER REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect filament leads of transformer from the
magnetron and capacitor.
4. Disconnect high voltage lead of capacitor from the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
transformer.
with two screws to the base cabinet, one is with outer
toothwasherandtheotheriswithoutouter-toothwasher.
5. Re-connect the wire leads (primary and high voltage)
and high voltage lead to the transformer and filament
leads of transformer to the magnetron and capacitor,
referring to the “Pictorial Diagram”.
5. Disconnect wire leads from the transformer.
6. Remove two (2) screws holding the transformer to the
base cabinet.
Re-install
1. Rest the transformer on the base cabinet with its primary
terminals toward rear cabinet.
2. Insert the two edges of the transformer into two metal
tabs of the base cabinet.
3. Make sure the transformer is mounted correctly to the
corners underneath those tabs.
4. Afterre-installingthetransformer,securethetransformer
6. Re-install the outer case and check that the oven is
operating properly.
NOTE HOT (ORANGE) WIRE MUST BE CONNECTED
TO THE POWER TRANSFORMER TERMINAL
NEAREST TO THE TRANSFORMER MOUNTING
SCREW.
MAGNETRON REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Dischargethehighvoltagecapacitor.Disconnectfilament
lead of transformer from magnetron. Disconnect high
voltage wire lead from magnetron.
3. Carefully remove four (4) mounting screws hold the
magnetron to waveguide, when removing the screws
holding the magnetron to prevent it from falling.
4. Remove the magnetron from the unit with care so the
magnetron tube should not hit by any metal object
around the tube.
CAUTION: WHEN REPLACING THE MAGNETRON, BE
SURE THE R.F. GASKET IS IN PLACE AND
THE MAGNETRON MOUNTING SCREWS
ARE TIGHTENED SECURELY.
HIGH VOLTAGE RECTIFIER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Remove one (1) screw holding the rectifier assembly to
the capacitor holder.
magnetron.
CAUTION: WHENREPLACINGTHESILICONRECTIFIER
ASSEMBLY, THE GROUND SIDE TERMINAL
MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.
4. Disconnecttherectifierassemblyfromthecapacitorand
HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect the high voltage wire leads and rectifier
assembly from high voltage capacitor and magnetron.
4. Disconnectfilamentleadoftransformerfromhighvoltage
capacitor.
5. Disconnect high voltage wire lead of capacitor from
transformer.
6. Remove one (1) screw and washer holding the rectifier
from the capacitor holder.
7. Remove one (1) screw holding the capacitor holder to
the rear cabinet.
8. Remove the capacitor from the holder.
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
Positive lock®
connector
1
Push the lever of positive lock® connector. Pull down on the
positive lock® connector.
Push
Lever
CAUTION: WHEN YOU CONNECTING THE POSITIVE
LOCK® CONNECTORS TO THE TERMINALS,
INSTALL THE POSITIVE LOCK® SO THAT
THE LEVER FACES YOU.
2
Pull down
Figure C-2. Positive lock®connector
CONVECTION MOTOR REMOVAL
1. Disconnect oven from power supply and remove outer case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from the convection motor.
Remove the convection fan belt.
5. Take out the convection motor assembly from the unit.
The convection motor assembly is now free.
6. Remove two (2) screws and nuts holding the motor to
mounting angle.
4. Remove two (2) screws holding the convection motor
mounting angle to the heater duct and base cabinet.
7. Remove pulley (M) from the motor shaft. Convection
motor is now free.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
TURNTABLE MOTOR REMOVAL
1. Disconnect the oven from power supply.
Remove the turntable tray, and the turntable support out
of the oven cavity.
2. Turn the oven upside down and remove one (1) screw
holding the turntable motor cover to the base plate and
take off the turntable motor cover.
3. Disconnect wire lead from the turntable motor.
4. Remove the two (2) screws holding the turntable motor
and coupling mounting plate to the oven cavity bottom.
5. Turntable motor, Coupling mounting plate and Thermal
protection plate bottom will be free.
DAMPER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from damper motor and damper
switch.
angle to thermal protection plate (right).
5. Damper assembly is free.
6. Remove one (1) screw holding damper motor to damper
motor angle and one (1) screw holding damper switch to
damper motor angle.
4. Remove two (2) oven side screws holding damper motor
7. Damper motor and switch are free.
HEATER UNIT ASSEMBLY REMOVAL
(HEATING ELEMENT/CONVECTION FAN/CONVECTION MOTOR/THERMISTOR)
THERMISTOR REMOVAL
HEATING ELEMENT REMOVAL
1. Disconnect oven from power supply and remove outer
case cabinet.
1. Remove two (2) screws holding heating element to
heater duct.
2. Loosen two (2) screws holding holders to heater duct
andtakeheatingelementoutofheatingelementholders.
3. Heating element is free.
2. Discharge the high voltage capacitor.
Disconnect wire leads from H.V. capacitor and remove
four (4) screws holding rear cabinet to bottom plate and
three (3) screws holding to heater unit assembly and two
(2) screws holding steam duct to top of oven cavity.
Disconnectwireleadsfrompowersupplycordterminals.
3. Disconnect wire leads from thermistor. Remove two (2)
screws from thremistor.
NOTE: After installed the heating element completely,
bent top of the heating element holder to inside
using by long nose pliers as shown following
illustration.
Long nose plier
4. Disconnect wire leads from convection motor, thermal
cut-out and heater element.
Heating
element
5. Remove nine (9) screws holding heater duct to the oven
cavity.
6. Remove two (2) screws holding heater duct to base
cabinet.Releasetwo(2)snapbandsholdingwireharness
to the thermal cover (convection).
7. The heater unit is now free.
Heating element
holder
OVEN LAMP AND LAMP SOCKET REMOVAL
Oven lamp
socket
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Bend the tab of the air guide holding the lamp socket.
4. Lift up the oven lamp socket.
Terminal
Wire lead
5. Pullthewireleadsfromtheovenlampsocketby pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
Terminal hole
Flate type small
screw driver
6. Now, the oven lamp socket is free.
Figure C-3. Oven lamp socket
FAN MOTOR REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect the wire leads from the fan motor.
4. Remove one (1) screw holding the fan motor grounding
wire to the air guide (Right).
5. Remove three (3) screws holding the chassis support to
the rear cabinet, waveguide and control panel back
plate.
6. Remove the chassis support from the oven.
7. Remove one (1) screw holding the magnetron air guide
to the waveguide.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
8. Remove the magnetron air guide from the waveguide.
9. Disconnect wire leads from the fan motor.
10. Release the main harness from the hole of the fan duct.
11. Release the thermistor harness from the hole of the fan
duct.
12. Release one (1) tab holding the fan duct to the rear
cabinet.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2)
screws and nuts.
2. Install the fan blade to the fan motor shaft according the
following procedure.
1) Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
13. Release one (1) tab holding the fan duct to the air guide
(Right).
14.Remove the fan duct assembly from the oven.
15.Removethefanbladefromthefanmotorshaftaccording
the following procedure.
2) Apply the screw lock tight into the hole (for shaft) of the
fan blade.
3) Install the fan blade to the shaft of fan motor by pushing
thefanbladewithasmall,lightweight,ballpeenhammer
or rubber mallet.
1) Hold the edge of the rotor of the fan motor by using a pair
of grove joint pliers.
CAUTION:
CAUTION:
*
*
*
Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
Make sure that the fan blade rotates smooth after
installation.
*
Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and
metal pieces may be produced.
Make sure that the axis of the shaft is not slanted.
3. Reset the fan duct assembly to its place.
4. Install the tabs of fan duct to the rear cabinet and air
guide.
*
*
Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
Do not disfigure the bracket by touching with the
pliers.
5. Install the magnetron air guide with the one (1) screw.
6. Reinstall the main harness and thermistor harness to
each hole of the fan duct.
7. Reinstall the chassis support to the control panel back
plate, waveguide and rear cabinet with the three (3)
screws.
2) Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
3) Now, the fan blade will be free.
CAUTION:
*
Donotusethisremovedfanbladeagainbecausethe
hole (for shaft) of it may become bigger than a
standard one.
8. Re-connect the wire leads to the fan motor, referring to
the pictorial diagram.
9. Re-install the fan motor grounding wire to the air guide
(Right) with one (1) screw.
16.Remove the two (2) screws and nuts holding the fan
motor to the fan duct.
17.Now, the fan motor is free.
Coil
Shaft
Groove joint pliers
Center of
bracket
Table
Side View
Rear View
Shaft
Axis
Stator
Gap
These are the position
where should be
pinched with pliers
Bracket
Rotor
Stator
Rotor
CONTROL PANEL ASSEMBLY AND CONTROL UNIT REMOVAL
To remove the control panel, procedure as follows:
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect connector CN-A, CN-E and CN-F from the
control unit.
4. Disconnect the wire leads from the relays RY1, RY2 and
RY3.
5. Remove one (1) screw holding the control panel back
plate to the chassis support.
6. Remove two (2) screws holding the bottom edge of the
back plate to the cabinet base.
7. Removeone(1)screwholdingthebackplatetotheoven
cavity flange.
8. Lift up and pull the control panel assembly forward.
Replacement of individual component is as follows;
CONTROL UNIT AND KEY UNIT
2. Remove the four (4) screws holding the panel frame to
the back plate.
3. Separate the panel frame and back plate.
4. Remove the three (3) screws holding the control unit to
the panel frame.
5. Lift up the control unit and disconnect the key connector
from the control unit.
6. Now,thecontrolunitandframeassemblyareseparated.
NOTE; 1.Beforeattachinganewkeyunit,removeremaining
adhesive on the control panel frame surfaces
completely with alcohol and so on.
2. When a attaching the key unit to the control
panel frame, adjust the lower edge and right
edge of the key unit to the correct position of the
control panel frame.
3. Stick the key unit firmly to the control panel
frame by rubbing with soft cloth not to scratch.
1. Disconnect the wire connector from the control unit.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Remove the control panel assembly, refer to "Control
Panel Removal".
4. Disconnect wire leads from each of the switches and
fuse holder.
5. Remove two (2) screws holding latch hook to oven
flange.
At this time switch lever will be free, do not lose it.
Re-install
1. Re-install switch lever and each interlock switch in its
place. The secondary interlock switch is in the lower
position and the door sensing switch is in the upper
position and the monitor switch is in the middle position.
2. Re-connectwireleadstoeachswitchesandfuseholder.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
6. Remove latch hook assembly from oven flange.
7. Push outward on the one (1) stopper tabs holding each
of switches place.
8. Switch is now free.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
If the door sensing switch, secondary interlock switch and
monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
1. Loosen the two (2) screws holding latch hook to the oven
DOOR SENSING
SWITCH
cavity front flange.
2. Withdoorclosed,adjustlatchhookbymovingitbackand
MONITOR FUSE
forth, and up and down. In and out play of the door
allowed by the latch hook should be less than 0.5mm.
3. Secure the screws with washers firmly.
MONITOR SWITCH
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm at the
SECONDARY
INTERLOCK
SWITCH
latched position.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Figure C-4. Latch Switch Adjustments
DOOR REPLACEMENT AND ADJUSTMENT
REMOVAL
Note: After any service to the door;
1. Disconnect oven from power supply and remove the
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter "Test Procedures".).
outer case.
Remove turntable tray and turntable support from oven
cavity.
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
2. Remove three (3) screws holding lower oven hinge.
3. Remove the lower oven hinge from oven cavity bottom
flange.
4. Remove door assembly from upper oven hinge on the
oven.
5. Door assembly is now free.
DOOR ADJUSTMENT
The door can be adjusted by keeping screws of each hinge
loose.
Note: When the individual parts are replaced, refer to
"Door Disassembly".
6. Onre-installingdoor, inserttheupperovenhingeintothe
door hinge pin. Then while holding door in place.
7. Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through
latch holes correctly.
8. Insert the lower oven hinge into oven cavity bottom
flange and then engaged the door hinge pin. Then
secure the lower oven hinge firmly with tree (3) mounting
screws.
After adjustment, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
Note: The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be
airtight, moisture (condensation)-tight or light-tight.
Therefore,occasionalappearanceofmoisture,light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity. If such were the case, your oven could not
be equipped with a vent, the very purpose of which
is to exhaust the vapor-laden air from the oven
cavity.
UPPER OVEN HINGE
RE-INSTALL
DOOR ASSEMBLY
LATCH
HEADS
LOWER OVEN HINGE
RE-INSTALL
Figure C-5. Door Replacement and adjustment
DOOR DISASSEMBLY
2
LIFT UP
Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
1. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door panel
areprovidedatseveralplaces,donotforceanyparticular
part.
PUTTY KNIFE
1
BENT
CHOKE COVER
Bent
INSIDE
FRONT
Door
Choke
cover
Panel
2. Insert an putty knife (thickness of about 0.5mm) into the
gap between the choke cover and corner portion of door
panel as shown Figure C-6 to free engaging parts.
3. Lift up choke cover.
Upper
Lower
4. Now choke cover is free from door panel.
Figure C-6. Door Disassembly
32
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
6
4
5
2
1
3
A
B
C
D
E
F
A
B
C
D
E
F
G
G
H
H
6
4
5
2
1
3
33
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
6
4
5
2
1
3
P 1
P 2
P 3
P 4
P 5
P 6
4
5
6
7
8
9
3 . 3 k
R 8 1
D 7 7
D 7 6
D 7 5
A
B
C
D
E
F
A
B
C
D
E
F
3 . 3 k
R 8 0
1 0 P 7
1 1 P 8
3 . 3 k
R 7 9
1 2 P 9
P 1 0
1 3
1 5 P 1 1
1 6 P 1 2
1 7 P 1 3
1 8 P 1 4
1 9 P 1 5
2 0 P 1 6
2 2 1 G
2 3 2 G
2 4 3 G
2 5 4 G
2 6 5 G
2 7 6 G
2 8 7 G
3 . 3 k
D 7 4
R 7 8
3 . 3 k
D 7 3
R 7 7
3 . 3 k
R 7 6 D 7 2
3 . 3 k
R 7 5 D 7 1
1 0 0 k
R 9 3
R 9 2
R 9 1
1 0 0 k
1 0 0 k
3 . 3 k
R 7 4 D 7 0
R 1 0 0 3 3 0 1 w
R 7 3 3 . 3 k
R 7 2 3 . 3 k
R 7 1 3 . 3 k
R 7 0 3 . 3 k
I C 1 I Z A 7 9 7 D R
C 7
R 7 4 . 7 k
C 8
R 6 4 2 . 2 k F
( J 7 )
( J 5 )
( J 3 )
( J 6 )
( J 4 )
( J 2 )
R 8 4 . 7 k
H Z 4 A 2
Z D 4
R 6 3 1 0 0 F
/ 3 µ 5 v C 6 1 0
/ 5 µ 0 v
C 5 0 . 1
/ 5 µ 0 v
C 9 0 . 0 1
H Z 5 C 2
Z D 3
/ 2 5 v
2 2
R 5 0 1 5 k
µ
R 4 0 3 . 3 k
/ 3 µ 5 v C 4 1 0
/ 5 µ 0 v
C 2 1 0 . 1
/ 5 µ 0 v
C 3 0 . 1
C 1 1
D 3 1
H Z 1 6 - 1
S P 4 0
R 3 0 1 5 k
Z D 2
4 7 0 1 / 2 w
/ 3 µ 5 v
C 2 0 1 0
R 2
/ 3 µ 5 v
C 2 1 0 0 0
C 1 0 . 1
/ 5 µ 0 v
/ 5 µ 0 v
C 2 2 0 . 1
D 2 3
D 2 0
D 2 1
D 2 2
D 2 4
D 2 5
D 2 6
G
G
1 0 G 4 7 1 K
V R S 1
( J 1 )
H
H
6
4
5
2
1
3
34
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
6
4
5
2
1
3
A
B
C
D
E
F
A
B
C
D
E
F
R
1
32
,F
B
E
Q90
1
2
R91
R92
3
C10
R80
R81
R93
R73
(C81)
R86(J8)
R72
R71
R70
D70
D71
D72
D73
D74
D75
D76
(C80)
(R45)
(C45)
C7
3
1
(CN - D)
D77
4
R79
R78
R77
R76
R75
6
ZD3
ZD4
R74
C9
R64
(R47)
(R48)
8
9
(R49)
C5
C6
10
11
12
(J7)
(J5)
(C46)
(C47)
C30
C50
C60
13
(J3)
(J2)
(J4)
14
15
(J6)
16
17
CONV
HEATER
RED
18
COM
BRN
D25
D24
E
B
Q40
C21
19
RY3
RY2
E
C3
B
B
Q25
Q24
D23
D31
D30
E
C4
R3
21
RY1
C2
22
B
C22
C1
Q21
E
23
RY5
24
B
Q20
E
RY4
G
G
C11
R10
R11
RY6
0
H
H
Figure S-3. Printed Wiring Board
6
4
5
2
1
3
35
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
PARTS LIST
◊Refer to "MPORTANT" described at end of parts list.
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
ELECTRICAL PARTS
1- 1
1- 2
1- 3
1- 4
1- 5
1- 6
1- 7
1- 8
1- 9
1-10
1-10
1-11
1-13
1-14
1-15
1-16
1-17
1-17
1-18
1-19
1-19
1-19
1-20
1-21
FACCDA048WRE0 Power supply cord
1
1
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AT
AH
AF
AK
AN
AK
AG
AL
AS
AK
AG
AG
AZ
AZ
AW
BP
AX
AV
AP
BL
BG
BN
AY
AY
FFS-BA012WRK0
Monitor fuse 20A and monitor switch (V-5220D-070) assembly
QFSHDA009WRE0 Fuse holder
QSW-MA110WRE0 Secondary interlock switch & outer case switches
FH-HZA041WRE0 Thermistor
QSW-MA110WRE0 Damper and door sensing switches
QFS-TA013WRE0 Magnetron temperature fuse 150˚C
RTHM-A085WRE0 Oven thermal cut-out 150˚C
RMOTDA192WRE0 Damper motor
RLMPTA071WRE0 Oven lamp
RLMPTA027WRE0 Oven lamp (Interchangeable)
QSOCLA021WRE0 Oven lamp socket
RMOTEA283WRE0 Convection fan motor
RMOTEA300WRE0 Fan motor
RHET-A136WRE0 Heating element
RTRN-A527WRE0 Power transformer
RC-QZA173WRE0 H.V.capacitor
RC-QZA211WRE0 H.V.capacitor (Interchangeable)
FH-DZA053WRK0 H.V.rectifier assembly
RV-MZA256WRE0 Magnetron
RV-MZA114WRE0 Magnetron (Interchangeable)
RV-MZA222WRE0 Magnetron (Interchangeable)
RMOTDA222WRE0 Turntable motor
FDTCTA183WRK0 AH sensor assembly
CABINET PARTS
2- 1
2- 1
2- 2
2- 3
2- 3-1
2- 3-2
2- 4
2- 5
2- 6
2- 7
2- 8
2- 9
2-10
GCABUA463WRP0 Outer case cabinet [R-930AW]
GCABUA457WRP0 Outer case cabinet [R-930AK]
TMAPCA732WRR0 Schematic diagram
FDAI-A179WRY0 Base cabinet
GCOVHA156WRP0 Turntable motor cover
XHTSD40P08RV0 Screw; 4mm x 8mm
GLEGPA019WRE0 Foot
1
1
1
1
1
1
4
1
1
1
1
1
1
BF
BF
AC
AX
AB
AA
AD
AS
AG
AG
AF
AM
AD
GCABDA087WRW0 Rear cabinet
LHLDKA009WRF0 Cord holder
LBNDKA036WRP0 Capacitor holder
FHNG-A092WRM0 Oven hinge (Lower)
PHOK-A043WRF0 Latch hook
MLEVPA122WRF0 Switch lever
CONTROL PANEL PARTS
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
3- 1E
3- 1F
C1
CPWBFA748WRK0 Control unit
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
7
2
8
BU
AC
AC
AD
AF
AY
AG
AB
AF
AB
AA
AB
AA
AH
AB
AB
AA
AA
AM
AB
AH
AH
AH
AE
AG
AB
AA
AA
AA
AA
QCNCMA227DRE0 5-pin connector(A)
QCNCMA267DRE0 6-pin connector(E)
QCNCMA237DRE0 3-pin connector(F)
QCNCWA057DRE0 12-pin connector(G)
RV-KXA077DRE0 Fluorescent display tube
PCUSGA381WRP0 Cushion
RC-KZA087DRE0 Capacitor 0.1µF 50V
VCEAB31VW108M Capacitor 1000µF 35V
RC-KZA087DRE0 Capacitor 0.1µF 50V
C2
C3
C4
VCEAB31VW106M Capacitor
10µF 35V
C5
RC-KZA087DRE0 Capacitor 0.1µF 50V
C6
VCEAB31VW106M Capacitor
10µF 35V
C7-8
C9
VCKYD11CY103N Capacitor 0.01µF 16V
VCTYF31HF103Z Capacitor 0.01µF 50V
RC-KZA087DRE0 Capacitor 0.1µF 50V
C10
C11
VCEAB31EW226M Capacitor
VCEAB31VW106M Capacitor
22µF 25V
C20
10µF 35V
C21
VCEAB31HW104M Capacitor 0.1µF 50V
RC-KZA087DRE0 Capacitor 0.1µF 50V
VCKYD11CY103N Capacitor 0.01µF 16V
VCKYD11CY103N Capacitor 0.01µF 16V
VCKYD11CY103N Capacitor 0.01µF 16V
RMPTEA009DRE0 Capacitor array 330pF x 4
RCRS-A035DRE0 Ceramic resonator (CST4.19MGW)
VHD11ES1///-1 Diode (11ES1)
VHD1SS270A/-1 Diode (1SS270ATA)
VHD1SS270A/-1 Diode (1SS270ATA)
VHD1SS270A/-1 Diode (1SS270ATA)
VHD1SS270A/-1 Diode (1SS270ATA)
C22
C30
C50
C60
C70
CF1
D1-4
D7
D20-26
D30-31
D70-77
Download from Www.Somanuals3.c6om. All Manuals Search And Download.
R-930AK
R-930AW
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
IC1
RH-IZA797DRE0 LSI
1
1
1
1
1
4
2
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
12
4
1
3
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
2
AX
AL
AE
AB
AA
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AK
AG
AG
AN
AE
AA
AA
AA
BE
BE
BA
BA
AE
AE
AB
AK
AE
AE
AA
AA
IC2
RH-IZA495DRE0 IC
Q1
VS2SB910MR/-4 Transistor (2SB910M)
VSKRA101M//-3 Transistor (KRA101M)
VSDTA123ES/-3 Transistor (DTA123E)
VSKRA101M//-3 Transistor (KRA101M)
VSKRA223M//-3 Transistor (KRA223M)
VSKRC243M//-3 Transistor (KRC243M)
VSKRA101M//-3 Transistor (KRA101M)
VSKRA101M//-3 Transistor (KRA101M)
VRD-B12HF471J Resistor 470 ohm 1/2W
VRD-B12HF331J Resistor 330 ohm 1/2W
VRD-B12HF751J Resistor 750 ohm 1/2W
VRD-B12EF472J Resistor 4.7k ohm 1/4W
VRS-B13AA180J Resistor 18 ohm 1W
VRD-B12EF153J Resistor 15k ohm 1/4W
VRD-B12EF472J Resistor 4.7k ohm 1/4W
VRD-B12EF332J Resistor 3.3k ohm 1/4W
VRD-B12EF153J Resistor 15k ohm 1/4W
VRD-B12EF472J Resistor 4.7k ohm 1/4W
VRN-B12EK753F Resistor 75k ohm(F) 1/4W
VRN-B12EK101F Resistor 100 ohm(F) 1/4W
VRN-B12EK222F Resistor 2.2k ohm(F) 1/4W
VRD-B12EF332J Resistor 3.3k ohm 1/4W
VRD-B12EF104J Resistor 100k ohm 1/4W
VRS-B13AA331J Resistor 330 ohm 1W
RRLY-A083DRE0 Relay (OMIF-S-118LM)
RRLY-A078DRE0 Relay (OJ-SH-118LM)
RALM-A014DRE0 Buzzer (PKM22EPT)
Q3
Q4
Q20-23
Q24-25
Q26
Q40
Q90
R2
R3
R4
R7-8
R10-11
R30
R31
R40
R50
R51
R62
R63
R64
R70-81
R90-93
R100
RY1-3
RY4-6
SP40
T1
RTRNPA022DRE0 Transformer
RH-VZA032DRE0 Varistor (10G471K)
VRS1
ZD2
ZD3
ZD4
VHEHZ161///-1 Zener diode (HZ16-1)
VHEHZ5C2///-1 Zener diode (HZ5C-2)
VHEHZ4A2///-1 Zener diode (HZ4A2)
DPNLCB438WRK0 Control panel frame with key unit [R-930AK]
DPNLCB439WRK0 Control panel frame with key unit [R-930AW]
FUNTKA815WRE0 Key unit [R-930AK]
3- 2
3- 2
3- 2-1
3- 2-1
3- 2-2
3- 2-2
3- 2-3
3- 3
3- 4
3- 5
3- 6
3- 7
FUNTKA816WRE0 Key unit [R-930AW]
JBTN-B059WRF0 Open button [R-930AK]
JBTN-B060WRF0 Open button [R-930AW]
MSPRCA050WRE0 Open button spring
LANGTA340WRW0 Control panel back plate
MLEVFA057WRW0 Open lever
NSFTTA042WRE0 Open shaft
XEPSD30P10XS0 Screw ; control unit mtg.
XCPSD40P12000 Screw ; control panel back plate mtg.
OVEN PARTS
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
FOVN-A314WRY0 Oven cavity assembly
FROLPA072WRK0 Turntable support
NTNT-A019WRH0 Turntable tray
FBRGMA002WRE0 Bearing ass’y
PREFHA028WRW0 Thermal protection plate (left)
LANGTA196WRW0 Bearing mounting plate
LBNDK0054WRE0 Heater element holder
LFIX-A013WRW0 Bearing holder plate
NFANMA019WRW0 Convection fan
NPLYBA020WRF0 Pulley (F)
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
BN
AL
AT
AQ
AR
AD
AB
AB
AE
AC
AT
AK
AE
AF
AG
BB
AC
AB
AM
AK
AC
AE
AE
AD
AD
AF
FDUC-A279WRK0 Heater duct assembly
PFPF-A138WRE0 Thermal protection sheet (left)
LANGKA723WRP0 Glass mounting plate
PCUSUA167WRP0 Cushion
PCUSUA424WRP0 Cushion
FDUC-A322WRW0 Steam duct assembly
MCAMPA030WRF0 Damper cam
NSFTTA114WRE0 Damper shaft
FFTA-A034WRK0 Damper door ass’y
PDUC-A269WRW0 Damper duct
PCUSGA398WRP0 Cushion
NCPL-A021WRF0 Turntable coupling
PCOVPA301WRE0 Waveguide cover
PCUSUA197WRP0 Cushion
PGLSPA455WRE0 Light glass
PFPF-A139WRE0 Thermal protection sheet (Right)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
4-43
PREFHA053WRW0 Thermal protection plate (Right)
PSKR-A153WRW0 Air guide (Bottom)
PSKR-A323WRW0 Air guide (Right)
LANGQA407WRW0 Convection motor mounting plate
NPLYBA021WRF0 Pulley (M)
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
AP
AK
AF
AG
AC
AE
AL
AE
AE
AF
AD
AD
AG
AH
AE
AF
AP
NFANJA020WRE0 Fan blade
PDUC-A270WRF0 Cooling fan duct
LANGFA089WRW0 Chassis support
MHNG-A165WRM0 Oven hinge (Upper)
NBLTKA005WRE0 Convection fan belt
MLEVFA086WRE0 Actuator
PCUSUA196WRP0 Cushion
PCUSUA425WRP0 Damper duct cushion
PCUSGA353WRP0 Cushion
PSKR-A171WRW0 Magnetron air guide
PFPF-A064WRE0 Thermal protection sheet
PHOK-A099WRF0 Switch holder
DOOR PARTS
5
CDORFA769WRK0 Door panel assembly complete [R-930AK]
CDORFA770WRK0 Door panel assembly complete [R-930AW]
DDORFA820WRY0 Door panel
PGLSPA499WRE0 Door glass [R-930AK]
PGLSPA500WRE0 Door glass [R-930AW]
GCOVHA155WRF0 Choke cover
GWAKPA492WRR0 Door frame [R-930AK]
GWAKPA494WRR0 Door frame [R-930AW]
LANGKA845WRW0 Glass bracket
LANGKA851WRT0 Latch angle
LSTPPA169WRF0 Latch head
MSPRTA081WRE0 Latch head spring
XCPSD40P08000 Screw; 4mm x 8mm
XEPSD30P08XS0 Screw; 3mm x 8mm
1
1
BT
BT
BD
AN
AN
AP
AZ
AZ
AF
AF
AH
AA
AA
AA
5
5- 1
5- 2
5- 2
5- 3
5- 4
5- 4
5- 5
5- 6
5- 7
5- 8
5- 9
5-10
1
1
1
1
1
1
2
1
1
1
2
16
MISCELLANEOUS
6- 1
6- 2
6- 3
6- 4
6- 5
6- 6
6 -7
6- 8
6- 8
6- 9
6-10
6-11
FAMI-A088WRM0 Low rack (Broiling trivet)
FAMI-A087WRM0 High rack (Baking rack)
TCADCA522WRR0 Cook book
1
1
1
1
1
1
1
1
1
1
1
1
AW
AW
BA
AN
BA
AN
AF
AE
AE
AB
AD
AH
FW-VZB342WRE0 Thermistor harness
FW-VZB595WRE0 Main wire harness
QW-QZA198WRE0 High voltage wire B
QW-VZA108WRE0 Grounding wire (Cooling fan motor)
TSPCNC464WRR0 Name plate [R-930AK]
TSPCNC467WRR0 Name plate [R-930AW]
TCAUAA200WRR0 Monitor caution label
TCAUAA209WRR0 DHHS caution label
TINSEA710WRR0 Operation manual
SCREWS NUTS AND WASHERS
7- 1
7- 2
7- 2
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
7-20
7-21
7-22
7-23
XOTWW40P10000 Screw; 4mm x 10mm
XOTSE40P12000 Screw; 4mm x 12mm [R-930AW]
XOTSF40P12000 Screw; 4mm x 12mm [R-930AK]
XCTWW40P08000 Screw; 4mm x 8mm
XHTSD40P08RV0 Screw; 4mm x 8mm
LX-CZ0052WRE0 Special screw
XWVSD60-07000 Washer; 6mm x 0.7 mm
LX-WZA004WRE0 Washer
LX-CZA020WRE0 Special screw
XBPSD30P14K00 Screw; 3mm x 14mm
XBPSD40P25000 Screw; 4mm x 25mm
XBTWW40P06000 Screw; 4mm x 6mm
XCTSD40P08000 Screw; 4mm x 8mm
XCPSD40P10000 Screw; 4mm x 10mm
XBPSD40P06KS0 Screw; 4mm x 6mm
LX-WZA022WRE0 Washer
XCPSD40P08000 Screw; 4mm x 8mm
XCPSD30P06000 Screw; 3mm x 6mm
LX-CZA038WRE0 Special screw
XFPSD40P08K00 Screw; 4mm x 8mm
XHTSD40R12RV0 Screw; 4mm x 12mm
XCBWW30P06000 Screw; 3mm x 6mm
XFPSD40P08000 Screw; 4mm x 8mm
XFPSD60P14JS0 Screw; 6mm x 14mm
14
4
4
2
1
2
1
1
6
1
2
7
7
1
2
1
6
3
1
2
1
4
6
2
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AB
Download from Www.Somanuals3.c8om. All Manuals Search And Download.
R-930AK
R-930AW
REF. NO.
PART NO.
DESCRIPTION
Q'TY
CODE
7-24
7-25
7-26
7-27
7-28
XOTSD40P12000 Screw; 4mm x 12mm
XFPSD30P08000 Screw; 3mm x 8mm
XNESD40-32000 Nut; 4mm x 3.2mm
XNEUW40-32000 Nut; 4mm x 3.2mm
XWSUW40-10000 Washer; 4mm x 1 mm
22
2
AA
AA
AA
AA
AA
2
1
1
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
Order Parts from the authrized SHARP parts Distributor for your area.
Defective parts required return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
TRAY HOLDER
(SPADFA348WRE0)
TOP PAD ASSEMBLY
FPADBA358WRK0
DOOR PROTECTION SHEET
SPADPA178WRE0
4-3 TURNTABLE TRAY
PLASTIC BAG
SSAKHA012WRE0
6-11 OPERATION
MANUAL
6-3 COOK BOOK
MICROWAVE OVEN
CABINET COVER (R-930AK)
SPADPA507WRE0
4-2 TURNTABLE SUPPORT
BOTTOM PAD ASSEMBLY
FPADBA359WRK0
TRAY PACKING FOAM
SPADPA198WRE0
PACKING CASE
SPAKCC905WRE0 (R-930AK)
SPAKCC909WRE0 (R-930AW)
Not replaceable items.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
6
4
5
2
1
3
OVEN AND CABINET PARTS
A
B
C
D
E
F
A
B
C
D
E
F
G
G
H
H
6
4
5
2
1
3
Download from Www.Somanuals4.c0om. All Manuals Search And Download.
R-930AK
R-930AW
6
4
5
2
1
3
CONTROL PANEL PARTS
3-7
3-3
x 2
A
B
C
D
E
F
A
B
C
D
E
F
3-1
3-6
3-2
x 3
3-4
7-24
3-2-1
3-5
7-24
3-2-3
5
5-3
3-2-2
5-10
DOOR PARTS
5-10
5-1
5-5
5-2
5-10
5-6
5-7
5-9
5-5
5-4
5-8
6-5
MISCELLANEOUS
G
G
6-1
6-4
6-2
H
H
Actual wire harness may be different than illustration.
6-7
6-6
6
4
5
2
1
3
41
Download from Www.Somanuals.com. All Manuals Search And Download.
R-930AK
R-930AW
'97 SHARP CORP. (6K2.770E) Printed in U.S.A
Download from Www.Somanuals.com. All Manuals Search And Download.
|