IMPORTANT SAFETY INSTRUCTIONS
When using your SHARK Bagless Spectra, basic safety precautions should
always be observed, including the following:
WARNING: To reduce the risk of fire,
electrical shock, or injury:
13. Do not use without filters in place. Use
ONLY filters and accessories provided
by EURO-PRO. Failure to do so will
void the warranty.
14. Turn off all controls before plugging or
unplugging vacuum cleaner.
1. Do not leave vacuum cleaner unattended
when it is plugged in. Unplug from
outlet when not in use and before filters.
2. To reduce the risk of electric shock – do
not use outdoors or on wet surfaces.
3. Do not allow children to use as a toy.
Close attention is necessary when used
by or near children.
4. Use only as described in this manual. Use
only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. Do
not use vacuum cleaner if it has been
dropped, damaged, left outdoors, or
dropped into water. Return appliance to
EURO-PRO for examination, repair or
adjustment.
6. Do not pull or carry by cord. Do not use
cord as a handle, close a door on cord,
or pull cord around sharp edges or
corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
8. Do not handle plug or vacuum cleaner
with wet hands. Do not use outdoors or
on wet surfaces.
9. Do not put any objects into openings. Do
not use with any opening blocked and
do not restrict airflow. Keep all openings
free of dust, lint, hair, and anything that
may reduce airflow.
10. Keep hair, loose clothing, fingers, feet and
all parts of body away from openings,
rotating agitator and other moving parts.
Do not operate cleaner in bare feet or
when wearing open toe shoes.
11. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking, or burning
objects.
15. Use extra care when vacuuming on
stairs.
16. Do not pick up flammable or
combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
17. Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
18. Do not use in an enclosed space filled
with vapors given off by oil based
paints, paint thinner, moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
19. Always unplug this appliance before
connecting or disconnecting vacuum
hose.
20. Use only on dry, indoor surfaces.
21. Do not use for any purpose other than
described in this user’s guide.
Bagless Cyclonic Upright
OWNER’S MANUAL
Model EP710
120V~, 60Hz., 12 Amps
22. The use of an extension cord is not
recommended.
23. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and
anything else that may reduce air flow.
24. Store your appliance indoors in a cool,
dry area.
25. Keep your work area well lit.
26. Do not immerse the vacuum into
water or other liquids.
27. Keep end of hose, wands and other
openings away from your face and
body.
12. Do not pick up hard or sharp objects such
as glass, nails, screws, coins, etc.
SAVE THESE INSTRUCTIONS
For Household Use Only
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
For information or assistance:
EURO-PRO Corporation
178 West Service Rd.
Champlain, N.Y., 12919
Tel.: 1-866-98shark (1-866-987-4275)
Rev. 10/02A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Assembling Your Vacuum Cleaner
Cord Assembly
Attachment Storage
Carpet Height Adjustment
1. Make sure that the quick release
cord holder is in the upright
position.
2. Remove the wire tie from the
power cord.
3. Wrap the cord into place by
wrapping it in a clockwise direction
around the quick release cord
holder and the lower cord holder
as shown. (fig. 3)
After the handle has been assembled to
the body of the vacuum and the power
cord has been wrapped around the
cord holders, the attachments can be
assembled.
1. Insert the end of the hose into one
of the extension tubes and place
this extension tube into the slot of
the inlet hose.
2. Loop the loose hose over the hose
hook.
3. Place the other extension tube into
the extension tube holder.
To select a pile height setting:
1. Turn vacuum cleaner "Off".
2. Select a pile height setting by tilting
the vacuum cleaner back until the
front wheels are lifted slightly off the
floor.
Note: Always remove the power plug
from the wall outlet before assembling or
removing accessories.
Handle Assembly
1. Remove the screw located just below
the top edge of the back of the
vacuum. (fig. 1)
3. Slide the adjustment lever to the
desired setting. (Fig. 6)
Suggested Pile Height Setting:
You may need to raise the height of the
vacuum to make some jobs easier,
such as scatter rugs and longer pile
carpets. Suggested settings are:
4. Slide the crevice tool inside the
extension tube when not in use.
5. Place the dusting brush into the
dusting brush holder.
HIGH:
shag carpet, long pile, plush
scatter rugs
MED:
LOW:
medium to long pile
short to medium pile, bare
floors
Fig. 1
How to Start
EX LOW: very low pile, bare floors
2. Position the handle as shown in fig. 2.
The upright vacuum can be used on
multiple types of carpeting, bare floors
or upholstery with attachments. When
using the attachment tools such as the
crevice tool and the dusting brush,
place the handle of the vacuum in the
upright position. (Fig. 5)
1. Turn the quick release cord holder
to either side 180° to release the
power cord.
2. Plug the power cord into the
electrical outlet.
3. Step on the handle release pedal
to release the handle.
Place unit in "HIGH" setting when using
attachments to prevent possible floor
damage.
Attention: Special care is required
when vacuuming certain types of carpet
or floor covering. Always check the
carpet or floor covering manufacturer's
recommended cleaning instructions
before vacuuming.
Fig. 3
4. Turn the quick release cord holder
to the left or to the right to unwrap
the power cord. (Fig. 4)
4. Step on the On/Off button to turn
the vacuum "On".
Fig. 2
3. While holding the power cord out of the
way, slide the handle into the opening at
the top of the vacuum.
Fig. 6
4. Insert the screw so that it passes
through the handle into the vacuum.
5. Begin to tighten the screw with your
fingers. It may be necessary to adjust
the handle slightly. Using a screwdriver,
tighten the screw.
Fig. 5
Caution: Do not over tighten. Over
tightening could strip
Warning: Do not plug in if the power
On/Off button is in the
the screw holes. Do not
operate the vacuum
without the screw in place.
"On" position.
Fig. 4
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Warning: To reduce the risk of electric
Releasing the Handle
1. Place the vacuum cleaner on a flat
surface and move the carpet height
adjustment to HIGH.
2. The crevice tool and the dusting
brush will fit both the extension
tubes and the hose. The dusting
brush will also fit on the end of the
crevice tool. (Fig. 8)
3. The extension tube can be
removed from the inlet hose by
grasping the cuff and twisting while
pulling up.
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
Release the handle by placing your foot
on the handle release pedal and pull
back on the handle until it releases from
its upright position. (Fig. 7)
HEPA Filter
with
Debris Screen
Removing & Emptying Dust Cup
The “Dust Cup” must always be emptied
when the dirt level reaches the "MAX
FULL" line on the dust cup.
To remove the dust cup from the
vacuum:
1. Press the dust cup release button
and lift the dust cup out and up of the
vacuum cleaner. (Fig. 9)
Debris Screen
HEPA Filter
Fig. 13
Caution:
• Do NOT pull the vacuum cleaner
around the room by the hose as it
could tip over and cause damage.
• When using the attachments, be
careful NOT to overextend the hose
length when reaching. Trying to
reach beyond the hose reach could
cause the vacuum cleaner to tip over.
2. Hold dust cup container with hand
and turn the dust cup cover counter
clockwise with the other hand to
remove. (Fig. 10)
3. Remove the HEPA "TAP CLEAN"
Filter from the dust cup.
Handle Release
Fig. 7
On/Off
Switch
Pedal
2. Vigorously "TapClean"
the HEPA dust cup
filter on a hard
Using the Attachments
surface until no
more dust is
observed falling
out. (Fig. 14)
Alternatively, the
HEPA filter may
also be washed by running it
under the tap allowing the water
to run on the dirty side. We
recommend washing it once a
month or when suction appears
reduced. Always allow 24 hours
for drying before replacing into the
vacuum.
Warning:
• Always turn vacuum "Off" before
attaching the accessories.
4. Empty the dust cup directly into
dustbin. (Fig. 11)
• Do NOT place hands or feet
underneath the agitator brush at any
time. When using the attachments,
the agitator brush continues to rotate.
• Do NOT allow the vacuum cleaner to
remain in just one place for a long
period of time as the agitator may
damage the floor surface.
• NEVER place the vacuum cleaner on
furniture, the fringed area of rugs,
deep pile carpeting or carpeted
stairs. The ideal position for the
vacuum cleaner when using any
attachment is for the unit to be on a
level surface with the handle in the
upright position and the carpet height
adjustment lever in HIGH.
Fig. 14
Fig. 8
Fig. 10
Fig. 9
3. "TapClean" the debris
screen or rinse under a
faucet until clean.
(Fig. 15) Debris screen
must be completely dry
(24 hours) be re-
installing on the HEPA
filter.
Fig. 15
ATTACHMENT USE CHART
4. When the debris screen is dry,
replace it on the HEPA filter and re-
install filter assembly into the vacuum.
(not shown)
Please Note: The white material in the
HEPA filter will discolor over time - This is
NORMAL and will NOT affect the
performance of the filter.
Warning: Always empty the dust cup
and clean the HEPA dust cup filter
before each use and during prolonged
usage. Never over fill the dust cup -
remove dirt and clean the HEPA dust
cup filter each time the dust cup is
emptied during prolonged usage or risk
motor damage.
Fig. 12
Fig. 11
CLEANING AREA
Drapes
5. Replace the dust cup back into the
vacuum by inserting the bottom first and
tilt back with the dust cup handle. Press
the dust cup release button to lock dust
cup in place.
Between
Cushions
ATTACHMENT
Furniture
Stairs
Walls
DUSTING
BRUSH
CREVICE
TOOL
*
*
*
*
*
*
*
Cleaning the HEPA Dust Cup Filter
We recommend that you "TAP CLEAN"
the HEPA Filter every time you empty the
dust cup.
1. When you have removed the HEPA
Filter from the dust cup, separate the
debris screen from the HEPA Filter.
(Fig. 13)
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Changing & Cleaning the Pre-
Cleaning the Dust Cup
Cleaning & Changing the Belt
10.Insert the right side of the agitator in
first by placing the rounded portion
of the end cap down into the slot
and then do the same with the left
side. Press firmly to make sure that
each end is completely inserted.
11.Check to make sure that the belt is
centered on the belt pulley and that
the agitator turns freely.
Motor Filter
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
The dust cup can be washed in
lukewarm water. Do not use strong
detergents. Ensure that the dust cup is
fully dry before putting back on the
vacuum cleaner. (Fig. 16) Do not wash
in dishwasher.
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
Occasionally the power nozzle drive
belt will require changing, the
frequency will depend upon the amount
of use your vacuum sees.
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
The pre-motor filter is located
underneath the dust cup. Please note
that this filter is not a washable filter
but should be cleaned frequently. To
remove the pre-motor filter:
1. Remove the dust cup from the
vacuum cleaner.
2. Make sure that you empty the dust
cup before turning it upside down to
remove the pre-motor filter.
3. Press inward on the two clips on
the side of the filter and pull out to
remove.
4. Clean the pre-motor filter by gently
tapping over a trash container.
5. Replace the filter into the dust cup
and push down until you hear it
click into place.
12.Replace the bottom plate over the
power head base and screw firmly.
1. Turn the vacuum "Off" and unplug
from power supply.
2. Release the handle by pressing on
the handle release pedal and pull
back on the handle until it releases
from its upright position. Then turn
the vacuum over and place on the
floor.
3. With a Phillips #2 screw driver
remove the five screws on the
bottom plate. (Fig. 17)
Fig. 18
Fig. 16
Changing the Headlight Bulbs
Warning: Always disconnect from
power source when servicing or
cleaning the unit. Failure to do so could
result in electrical shock or personal
injury from cleaner suddenly starting.
Motor Thermostat
Changing & Cleaning the Exhaust
Filter
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
Important: This motor is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
• if clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 30 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
30 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact EURO-PRO at 1-800-
798-7398.
• Turn unit “Off” and unplug from
wall outlet.
• Snap the lens cover off by pressing
down to release the two notches on
the lens. (Fig. 19)
• Remove the light bulbs by pulling
them out carefully.
• Replace with new bulbs by pushing
them in.
Fig. 17
The exhaust filter is located on the
front of the unit below where the dust
cup is.
1. Check the exhaust filter frequently
and clean when dirty.
4. Carefully remove any residue that
may exist in the belt area.
5. If the belt has broken, remove any
loose pieces before replacing.
6. Hold the agitator with your hand. If
the belt is still attached to the
agitator, there will be tension on it.
7. Carefully lift the left side of the
agitator and then the right side.
8. Remove the worn or broken belt
from the motor drive shaft.
9. Loop the new belt first over the
drive shaft and then over the belt
pulley on the agitator. (Fig. 18)
• Replace the lens cover.
2. Press inward on each side of the
exhaust filter cover and pull out to
remove from the vacuum cleaner.
3. Remove the exhaust filter.
4. Rinse in lukewarm water and dry
the filter completely before re-
installing into the vacuum. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry
it. Air dry only. Never operate the
vacuum without the filters in place.
5. When the filter is dry, replace into
the vacuum and replace the filter
cover.
Lens
Fig. 19
Note: A severely soiled or clogged
filter should be thoroughly washed with
fresh tepid water. A mild detergent can
be used if required.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition
when it was shipped from the factory. If a minor problem occurs, it usually can
be solved quite easily when the cause is found. Therefore, this checklist is
provided for your convenience.
PROBLEM
POSSIBLE CAUSE
POSSIBLE
1. Not firmly plugged in.
2. No electricity in wall
outlet.
3. On/Off switch not turned
on.
4. Thermal protector tripped.
5. Blown fuse/tripped
breaker.
1. Plug in firmly, push on/off
switch to on.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset thermal protector.
(page 8 )
Cleaner Won’t
Run
Bagless Cyclonic Upright
5. Reset circuit breaker or
replace fuse.
TO ORDER REPLACEMENT BAGS, FILTERS OR
BELTS
for Model EP710
1. Full or clogged dust cup.
2. Wrong pile height setting. 2. Adjust setting. (page 5)
3. Clogged nozzle or dust
cup port.
4. Clogged hose.
5. Hole in hose.
6. Broken / misplaced belt.
7. Hose not inserted fully.
8. Motor protection system
activated.
1. Clean dust cup. (page7)
3. Remove obstruction.
4. Remove obstruction.
5. Replace hose.
6. Replace / fix belt. (page 9)
7. Push hose in securely.
8. Reset thermal protector.
(page 8)
Call:
1-866-98SHARK (1-866-987-4275)
Cleaner Won't
Pick Up
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
or
9. Clean / change filters.
(page 7/8)
FOR TECHNICAL SUPPORT
9. Dirty filters.
for Model EP710
Cleaner Picks
Up Moveable
Rugs Or
Call:
1-800-798-7398
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
1. Wrong pile height setting. 1. Adjust setting. (page 5)
Pushes Too
Hard
Please Note:
1. Replace belt. (page 9)
1. Broken belt.
Agitator Does
Not Turn
Post Motor Filter is washable. It should however be replaced
every three (3) months to ensure peak performance of your
vacuum.
2. Check belt changing and
2. Belt installed incorrectly.
agitator cleaning. (page 9)
Air Flow
1. Attachment use restricts
Restricted With
Attachment Use
Sound Changes
1. Check attachment. (page 6)
2. Remove obsrtuction.
air flow.
2. New carpet fuzz clogged
air path.
Important:
Make sure that the Filters are completely dry before inserting
back in the vacuum.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Model EP710
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO CORPORATION warrants this product to be free from defects in material
and workmanship for a period of one (1) year from the date of the original purchase.
This warranty applies only to normal domestic household use.
Should your appliance fail to operate properly while in use under normal household
conditions within the one (1) year warranty period, return the complete appliance and
accessories, freight prepaid to Euro-Pro Corporation at the address given below.If the
appliance is found by EURO-PRO to be defective in material or workmanship, EURO-
PRO will repair or replace it free of charge. Proof of purchase date and $16.95 to cover
the cost of return shipping and handling must be included. *
In US:
EURO-PRO Corporation, 178 West Service Rd., Champlain, N.Y. 12919
If the appliance is found by EURO-PRO to be defective in material or workmanship,
EURO-PRO will repair or replace it free of charge. Include $16.95 to cover the cost of
return shipping and handling must be included. *
Non-durable parts including, without limitation, disposable dust bags, drive belts,
rotating brushes and electrical parts which normally require replacement are specifically
excluded from warranty.
The liability of EURO-PRO Corporation is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts
and does not apply to any unit that has been tampered with or used for commercial
purposes. This limited warranty does not cover damage caused by misuse, abuse,
negligent handling or damage due to faulty packaging or mishandling in transit. This
warranty does not cover damage or defects caused by or resulting from damages from
shipping or repairs, service or alterations to the product or any of its parts, which have
been performed by a repair person not authorized by EURO-PRO.
This warranty is extended to the original purchaser of the unit and excludes all other
legal and/or conventional warranties. The responsibility of EURO-PRO Corporation if
any, is limited to the specific obligations expressly assumed by it under the terms of the
limited warranty. In no event is EURO-PRO Corporation liable for incidental or
consequential damages of any nature whatsoever. Some states do not permit the
exclusion or limitation of incidental or consequential damages, so the above may not
apply to you.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include
proof of purchase date and to attach tag to item before packing with your name,
complete address and phone number with a note giving purchase information,
model number and what you believe is the problem with item. We recommend you
insure the package (as damage in shipping is not covered by your warranty). Mark
the outside of your package “ATTENTION CUSTOMER SERVICE”. We are
constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|