HMEC 350/352/355
355-C/356/372/450
HMDC 372
Instructions for use
Download from Www.Somanuals.com. All Manuals Search And Download.
The HMEC 350, HMEC 352, HMEC 355, HMEC 355-C, HMEC 356, HMEC 372, HMEC 450 and
HMDC 372 are pilot headsets with closed ear protector headphones and NoiseGard™
active noise compensation for use in helicopters, propeller and turboprop aircraft.
Safety tips
•
With the NoiseGard™ active noise compensation turned on, typical aircraft sounds
(for example, those from engines, propellers, warning alarms, etc.) may sound
different to you. Before operating any aircraft, make sure that, with NoiseGard™
turned on, you can hear and recognize these sounds. Set the volume to safe levels
that do not interfere with your ability to hear informational sounds and warning
alarms.
•
•
•
Do not attempt to repair the headset yourself. If problems occur, contact your
Sennheiser agent for assistance.
Only replace parts of the headset whose replacement is described in this manual. All
other parts of the headset must be replaced by your Sennheiser agent.
Do not immerse the headset in water! For information on how to clean the headset,
contact your Sennheiser agent.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Headset features
HMEC 350 NoiseGard™ headset
•
•
•
New active headset with effective attenuation of external noise across the entire
frequency spectrum due to NoiseGard™ active noise compensation
NoiseGard™ active noise compensation provides clear communications even in the
noisiest environment
Improved acoustic properties: The frequency response of the headphones has been
optimised in the 1 to 4 kHz region to give significantly increased speech intelligibility
over the HMEC 300 series
•
Excellent comfort due to very low weight, soft ear cushions and padded headband as
well as best possible freedom of movement due to unilateral connecting cable
•
•
Foldable headband for easy and space-saving storage
Clear communications due to MKE 45-1 pre-polarized condenser microphone with
adjustable sensitivity
•
Microphone can be easily positioned and worn on either left or right side due to
flexible microphone boom with quick-fixing device
•
•
Integrated volume control
Adaption to the aircraft intercom system via Mono/Stereo switch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
With the NoiseGard™ active noise compensation turned off, the headset can be used
as a conventional headset
Power supply for NoiseGard™ is provided via on-board power supply system,
cigarette lighter socket or battery pack
•
•
Fail safe operation in case of power failure
Supply voltage for the NoiseGard™ system is processed by the in-line electronics in
the connecting cable
•
Made in Germany, 5-year warranty (HMEC 450: 10-year warranty)
Product variants
HMEC 352 NoiseGard™ headset
The HMEC 352 differs from the HMEC 350 in the following features:
•
Connection of microphone and NoiseGard™ electronics via PJ-068 plug
HMEC 355 NoiseGard™ headset
The HMEC 355 differs from the HMEC 350 in the following features:
•
•
No Mono/Stereo switch
Connection of headphones, microphone and NoiseGard™ electronics to the on-board
power supply system (12–35 V DC) via XLR-5 plug
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 355-C NoiseGard™ headset
The HMEC 355-C differs from the HMEC 350 in the following features:
•
•
•
No Mono/Stereo switch
Connection of headphones and microphone via XLR-5 plug
Connection of NoiseGard™ electronics via XLR-3 plug
HMEC 356 NoiseGard™ headset
The HMEC 356 differs from the HMEC 350 in the following features:
•
Connection of headphones, microphone and NoiseGard™ electronics to the on-board
power supply system (12–35 V DC) via 6-pin Redel plug
HMEC 372 NoiseGard™ headset
The HMEC 372 differs from the HMEC 350 in the following features:
•
•
•
No Mono/Stereo switch
Coiled cable
Connection of headphones and microphone via U-174/U jack plug to a high impedance
interface in the helicopter
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 450 NoiseGard™ headset
The HMEC 450 differs from the HMEC 350 in the following features:
•
•
•
Stylish silver design
Leatherette ear cushions
Headband padding can be buttoned
HMDC 372 NoiseGard™ headset
The HMDC 372 differs from the HMEC 350 in the following features:
•
•
•
•
No Mono/Stereo switch
Coiled cable
M-87/AIC dynamic microphone and low impedance headphones
Connection of headphones and microphone via U-174/U jack plug to a low impedance
interface in the helicopter
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Delivery includes
HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 headsets
•
•
•
•
•
Headset
3-pin XLR socket for aircraft panel mounting (power supply via the on-board system)
Padded carry and storage bag with shoulder strap for headset and accessories
Wind screen for microphone (except HMDC 372)
MZQ 2002-1 cable clip (Cat. No. 044740)
HMEC 352, HMEC 355 and HMEC 356 headsets
•
•
•
•
Headset
Padded carry and storage bag with shoulder strap for headset and accessories
Wind screen for microphone
MZQ 2002-1 cable clip (Cat. No. 044740)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended accessories
Replaceable gel ear cushions (Cat. No. 092807)
BP-04 battery pack (Cat. No. 500357) (except for HMEC 352, HMEC 355 and HMEC 356)
Battery pack with XLR-3 socket for powering the NoiseGard™ electronics of the
HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 headsets. Four 1.5 V AA
size alkaline manganese batteries (IEC LR 6) ensure approx. 15 hours of reliable
operation (batteries are not included in the delivery). Length of connecting cable: 0.9 m.
Adapter cables (except for HMEC 352, HMEC 355 and HMEC 356)
Sennheiser offers special adapter cables for connecting the NoiseGard™ electronics of
the HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 headsets to the on-
board power supply via the cigarette lighter socket:
ACX-2
ACX-1
•
•
ACX-1 adapter cable for powering one headset via the cigarette lighter socket
ACX-2 adapter cable for powering two headsets via the cigarette lighter socket
The adapter cables are also available with a right-angled jack plug featuring a 7.5 A fuse
and a green LED operation indicator:
•
•
ACX-11 adapter cable for powering one headset via the cigarette lighter socket
ACX-11
ACX-22
ACX-22 adapter cable for powering two headsets via the cigarette lighter socket
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the headsets
Connecting cables for headsets
HMEC 350 and HMEC 450 headsets:
1
1
1
¼” (6.35 mm) stereo jack plug for connecting the headphones
PJ-068 jack plug for connecting the microphone
XLR-3 plug for connecting the power supply for the NoiseGard™ electronics
Connecting cable for
HMEC 350 and HMEC 450
HMEC 352 headset:
1
1
¼” (6.35 mm) stereo jack plug for connecting the headphones
PJ-068 jack plug for connecting the microphone and the power supply for the
NoiseGard™ electronics
Connecting cable for
HMEC 352
HMEC 355 headset:
1
XLR-5 plug for connecting the headphones, the microphone and the power supply for
the NoiseGard™ electronics
Connecting cable for
HMEC 355
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 355-C headset:
1
1
XLR-5 plug for connecting the headphones and the microphone
XLR-3 plug for connecting the power supply for the NoiseGard™ electronics
Connecting cable for
HMEC 355-C
HMEC 356 headset:
1
6-pin Redel plug for connecting the headphones, the microphone and the power
supply for the NoiseGard™ electronics
Connecting cable for
HMEC 356
HMEC 372 and HMDC 372 headsets:
1
1
U-174/U jack plug for connecting the headphones and the microphone
XLR-3 plug for connecting the power supply for the NoiseGard™ electronics
Connecting cable for
HMEC 372 and HMDC 372
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector assignment
Redel connector (NoiseGard™)
XLR-3 connector (NoiseGard™)
XLR-5 connector
1
2
3
4
5
6
Power supply NoiseGard™ (DC+) 1 Power supply NoiseGard™ (DC+) HMEC 355
HMEC 355-C
Audio Lo / DC –
Audio Hi left
2
3
Ground
– *
1
2
3
4
5
Audio Hi
1
2
3
4
Audio Hi
Audio Lo
Microphone Hi
Microphone Lo
Audio Lo / DC –
Microphone Hi
Microphone Lo
Audio Hi right
Microphone Hi
Microphone Lo
Power supply NoiseGard™ (DC+) 5 Not assigned!
¼” (6.35 mm) stereo jack plug
U174/U jack plug
PJ-068 jack plug
1
2
3
Audio Hi left
Audio Hi right
Audio Lo
1
2
3
4
Microphone Lo
Audio Hi
Microphone Hi
Audio Lo
HMEC 352
HMEC 350
1
2
3
Power supply NoiseGard™ (DC+) 1 Not assigned!
Microphone Hi
Microphone Lo / DC –
2
3
Microphone Hi
Microphone Lo
* Note: Battery powering for the NoiseGard™ system of HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 only via BP-04 battery pack
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering options
There are three options for powering the NoiseGard™ active noise compensation:
1. Connection to the on-board system (12–35 V DC)
2. Connection to the BP-04 battery pack
(accessory, except for HMEC 352, HMEC 355 and HMEC 356)
3. Connection to the cigarette ligther socket (12–35 V DC) via adapter cable
(accessory, except for HMEC 352, HMEC 355 and HMEC 356)
The supply voltage for the NoiseGard™ system is processed by the in-line electronics in
the connecting cable.
Danger of short circuit!
Before turning on NoiseGard™, ensure that the on-board power supply system is
protected by a 1 A fuse.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Connecting the headset to the on-board system
The NoiseGard™ electronics can be connected to on-board power supply systems with
operating voltages between 12–35 V DC.
Danger of short circuit!
Before turning on NoiseGard™, ensure that the on-board power supply system is
protected by a 1 A fuse.
The HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 headsets are supplied
with an XLR-3 socket for panel mounting in the aircraft. The XLR-3 socket must be
mounted by a technician qualified to perform this type of installation.
Power supply for
NoiseGard™
Ground
Do not connect !
XLR-3 socket
HMEC 350 and HMEC 450 headsets:
̈ Connect the ¼” (6.35 mm) stereo jack plug for the headphones and the PJ-068 jack
plug for the microphone to the corresponding jack sockets of your intercom.
̈ Connect the XLR-3 plug to the XLR-3 socket.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 352 headset:
̈ Connect the ¼” (6.35 mm) stereo jack plug for the headphones and the PJ-068 jack
plug for the microphone to the corresponding jack sockets of your intercom.
HMEC 355 headset:
̈ Connect the XLR-5 plug to the aircraft’s XLR-5 socket.
HMEC 355-C headset:
̈ Connect the XLR-5 plug for the headphones and the microphone to the aircraft’s XLR-5
socket.
̈ Connect the XLR-3 plug to the XLR-3 socket.
HMEC 356 headset:
̈ Connect the 6-pin Redel plug to the corresponding socket in the aircraft.
HMEC 372 and HMDC 372 headsets:
̈ Connect the U-174/U jack plug for the headphones and the microphone to the U-174/U
socket of your intercom.
̈ Connect the XLR-3 plug to the XLR-3 socket.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connecting the headset to the battery pack
(except HMEC 352, HMEC 355 and HMEC 356)
The NoiseGard™ electronics of the HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and
HMDC 372 headsets can also be powered via the BP-04 battery pack (see
“Recommended accessories” on page 9). The battery pack can be operated either on
standard or rechargeable batteries (not included in the delivery). However, to ensure a
longer operating time, we would recommend using standard AA size alkaline
manganese batteries (IEC LR 6) or NiMH rechargeable batteries.
Inserting / replacing the the batteries
̈ Open the cover of the battery compartment.
̈ Insert four AA size alkaline-manganese batteries (IEC LR 6). Observe correct polarity
when inserting the batteries.
̈ Close the cover of the battery compartment.
LED operation and battery status indication
The battery pack has two control LEDs.
Yellow LED: The battery pack is turned on and the battery capacity is sufficient.
Red LED:
The batteries are low. Replace the batteries.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the headset, turning on the battery pack
̈ Connect the XLR-3 plug of the headset connecting cable to the XLR-3 socket on the
connecting cable of the battery pack.
̈ HMEC 350 and HMEC 450 headsets: Connect the ¼” (6.35 mm) stereo jack plug for
the headphones and the PJ-068 jack plug for the microphone to the corresponding
jack sockets of your intercom.
HMEC 355-C headset: Connect the XLR-5 plug for the headphones and the
microphone to the aircraft’s XLR-5 socket.
HMEC 372 and HMDC 372 headsets: Connect the U-174/U jack plug for the
headphones and the microphone to the U-174/U socket of your intercom.
̈ Turn on the battery pack by setting the ON/OFF switch to ON. The yello LED power
indicator lights up.
Note:
When using the battery pack, the ON/OFF switch integrated into the headset
connecting cable is out of operation.
Attaching the battery pack to clothing
The battery pack can be attached to clothing by means of the supplied attachment clip,
Velcro tape is also supplied.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connecting the headset via a cigarette lighter adapter cable
(except HMEC 352, HMEC 355 and HMEC 356)
Sennheiser offers special adapter cables with XLR-3 socket for connecting the NoiseGard™
electronics of the HMEC 350, HMEC 355-C, HMEC 372, HMEC 450 and HMDC 372 headsets
to the on-board power supply via the cigarette lighter socket:
•
•
ACX-1 adapter cable for powering one headset via the cigarette lighter socket
ACX-1
ACX-2
ACX-2 adapter cable for powering two headsets via the cigarette lighter socket
The adapter cables are also available with a right-angled jack plug featuring a 7.5 A fuse
and a green LED operation indicator:
•
•
ACX-11 adapter cable for powering one headset via the cigarette lighter socket
ACX-22 adapter cable for powering two headsets via the cigarette lighter socket
ACX-11
ACX-22
Connecting the headset
̈ Connect the XLR-3 plug of the headset connecting cable to the XLR-3 socket of the
adapter cable.
̈ Connect the plug or right-angled jack plug of the adapter cable to the cigarette
lighter socket.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the headsets for use
Adjusting the headband
For good noise attenuation and best possible comfort, the headband has to be adjusted
to properly fit your head:
̈ Wear the headset so that the headband runs over the top of your head.
̈ Adjust the length of the headband so that
• your ears are completely inside the ear cushions,
• you feel even, gentle pressure around your ears,
• a snug fit is ensured.
Note:
Make sure not to squeeze any connecting cable when adjusting the headband.
Squeezing can damage the connecting cables.
̈ Turn on the NoiseGard™ active noise compensation by setting the ON/OFF switch to
“ON” (see “Turning NoiseGard™ on/off” on page 22).
̈ Final adjustment is best made in a noisy environment.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the microphone
Relocating the microphone boom
The microphone boom can be worn on either side of the mouth.
̈ Loosen the quick-fixing device.
̈ Rotate the microphone boom by 180°.
̈ Tighten the quick-fixing device.
Positioning the microphone towards the corner of the mouth
The HMEC 350, HMEC 352, HMEC 355, HMEC 355-C, HMEC 356, HMEC 372 and HMEC 450
headsets feature a flexible microphone boom. Bend the microphone boom so that the
microphone is placed at the corner of the mouth. Maintain a distance of approx. 2 cm
between microphone and mouth.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
For positioning the microphone of the HMDC 372 headset, proceed as follows:
̈ Adjust the length of the microphone boom so that the microphone is placed at the
corner of the mouth. To do so, loosen the quick-fixing device and adjust the
microphone boom in length.
̈ Pull the middle part of the microphone boom towards the mouth so that the distance
between microphone and mouth is approx. 2 cm.
̈ Tilt the microphone for final positioning.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the headsets
Turning NoiseGard™ on/off
With the NoiseGard™ active noise compensation turned off, the headset can be used as
a conventional headset.
Turn on the NoiseGard™ active noise compensation by setting the ON/OFF switch to
“ON”. When using the BP-04 battery pack, set the NoiseGard™ ON/OFF switch to “ON”
and use the ON/OFF switch on the battery pack.
Mono/Stereo selection (except HMEC 355, HMEC 355-C, HMEC 372 and HMDC 372)
In general, you’ll receive a mono sound source so that the Mono/Stereo switch can
remain set to “Mono”. When using a stereo intercom system, set the Mono/Stereo
switch to “Stereo”.
Adjusting the volume
Exposure to loud sounds can cause hearing damage!
Set the volume control to a medium value. Make sure that you can hear critical sounds
such as warning alarms.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the cable clip
The headphone cable can be fixed by means of the cable clip. Guide the headphone cable
through the metal cable clip as shown in the illustration on the left. Attach the cable clip
to your clothing and then loop the cable through the clip so that the headphone cable
doesn‘t disturb you.
Folding up the headphones
For easy and space-saving transportation, the earcups can be folded up and tucked
between the headband.
Unfold the headphones by grasping both earcups and pulling them down and away from
the headband.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Spare parts
The following spare parts are available from your Sennheiser agent:
•
•
•
•
•
•
•
Wind screen for MKE 45-1
Cat. No. 075823
Cat. No. 077966
Cat. No. 085764
Cat. No. 089382
Cat. No. 086628
Cat. No. 044740
Cat. No. 078366
Ear cushions for all variants except HMEC 450
Ear cushions for HMEC 450
Soft ear cushions for HMEC 450
Headband padding
MZQ 2002-1 cable clip
Carry and storage bag with shoulder strap
Replacing the wind screen
If the wind screen shows signs of wear such as tears or holes, replace the wind screen.
Pull the wind screen from the microphone. Gently slide-on the new wind screen and
ensure that it fits securely over the microphone.
Replacing the ear cushions
Replace the ear cushions if they are damaged. Grasp behind the ear cushions and pull
them up and away from the earcups. Fix the new self-adhesive ear cushions to the
earcups. For best results replace the ear cushions after 100 hours of use or two years.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the headband padding
Replace the headband padding if it is damaged.
̈ Pull the Ziploc type fastening strips of the headband padding apart and remove the
worn headband padding.
̈ Put the new headband padding around the headband.
̈ Pull the two edges of the headband padding together so that the fastening strips
slightly overlap.
̈ Join the fastening strips.
Replacing the headband padding of the HMEC 450 headset
Replace the headband padding if it is damaged.
̈ Open the snaps on the headband padding and remove the worn headband padding.
̈ Put the new headband padding around the headband.
̈ Pull the two edges of the headband padding together and close the snaps.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Valuable information on NoiseGard™
The NoiseGard™ principle
One of the greatest stress factors today is noise. Research has shown that noise affects
the nervous system, and can cause tiredness, poor concentration, irritability and tension.
Of even greater concern is the permanent damage to hearing that can result from noise
at high levels.
This problem concerns pilots in particular. Cockpit noise amounts to about 80 dB(A) in
jets and to 90 up to 97 dB(A) in turboprops. During takeoff and landing, the noise level
is even higher. To be able to understand radio traffic in spite of the noisy environment,
the ATC signal level must be set to at least 95 dB(A). Permanent hearing loss caused by
the continuous noise in aircrafts is the reason why many pilots became prematurely
disabled or lost their pilot´s license.
Circumaural communication headsets provide noise attenuating properties and are
commonly used to address this problem. However, the noise attenuation of these
headsets is uneven. High frequencies are reduced considerably, but low frequency wind
and engine noise, the most prominent noise in many of today's aircrafts, is attenuated
very little. In response to these problems, Sennheiser has developed an active noise
compensation system – NoiseGard™ – which, combined with a high-quality passive
hearing protector, provides consistent noise attenuation over the entire audio range.
The overall noise level is reduced so that the radio volume can be turned down but
enough noise still remains for the pilot to safely monitor the aircraft engines.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NoiseGard™ active noise compensation is achieved by generating a signal identical in
sound pressure level but exactly reversed in phase to the noise signal, the effect being
that the out-of-phase signal cancels most of the noise signal.
Active noise compensation is accomplished in the following manner: Each earcup
includes a microphone, a feedback control circuit, and a transducer to reproduce both
the communication and the noise cancelling signal. The feedback control microphones
sense the total sound pressure within each earcup resulting from both the desired radio
signal from the receiver and the undesired noise that has come through the earcup. The
microphone signal is amplified and the radio signal is subtracted from it. The remaining
signal (noise) is then filtered and inverted and the radio signal is added back in.
Eventually, the entire signal is amplified and fed back to the transducer in each earcup.
Since the noise component of the signal is inverted, it cancels the noise signal coming
through the earcup. The radio signal remains unaffected, as it was not processed
through the cancellation circuits.
The diagram on the left shows noise compensation with NoiseGard™: Passive hearing
protectors effectively attenuate noise from the middle and upper frequency range, the
effect decreasing sharply in the lower range. However, active noise compensation with
NoiseGard™ combined with passive hearing protectors results in a reduction of noise of
approx. 25 dB in the 25–500 Hz frequency range. The total attenuation resulting from
active and passive noise compensation is about 30 dB over the entire audio range.
A 10 dB reduction in noise is perceived subjectively as a halving in volume. A further
reduction in noise of 10 dB again results in a decrease in unwanted noise by 50 %.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of difficulty
If problems occur that are not listed in the below table, please contact your Sennheiser
agent.
Problem
Possible cause and what to do
Clear communication but no
active noise compensation
The NoiseGard™ electronics are turned off.
̈ Check to see if the ON/OFF switch is set to “ON”.
The XLR-3 plug has been pulled out of the power source.
̈ Check to see if the XLR-3 plug is correctly connected to the power source.
If aircraft powered: The aircraft fuse is defective.
̈ Check the aircraft fuse.
If battery powered (except HMEC 352, HMEC 355 and HMEC 356): The batteries are low.
̈ Check to see if the yellow LED on the battery pack is lit. If the red LED is lit, replace
the batteries.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause and what to do
Active noise compensation but
very low volume communication
The volume control is set too low.
̈ Check the volume setting of the headset.
The headphone connection has been pulled out (except HMEC 355, HMEC 355-C and
HMEC 356).
̈ Check to see if the headphone jack plug is correctly connected.
Active noise compensation but
reduced intelligibility
The microphone connection has been pulled out (except HMEC 355, HMEC 355-C and
HMEC 356).
̈ Check to see if the microphone jack plug is correctly connected.
Communications in one ear only
(only HMEC 350, HMEC 352,
HMEC 356 and HMEC 356)
You are using a stereo intercom system but the headset is set to mono operation.
̈ Set the Mono/Stereo switch to “Stereo”.
You are receiving a mono source but the headset is set to stereo operation.
̈ Set the Mono/Stereo switch to “Mono”.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
HMEC 350
ꢀ HMEC 352
ꢀ HMEC 356
ꢀ HMEC 450
Headphones
Transducer principle
dynamic
Ear coupling
circumaural, closed
45–15,000 Hz
Frequency response
Nominal impedance active/passive
300/150 Ω, mono
600/300 Ω, stereo
Attenuation (active and passive)
Max. sound pressure level
Contact pressure
> 25–40 dB
120 dB ( 5 %)
approx. 10 N
Microphone incl. preamplifier
Transducer principle
pre-polarized condenser mic capsule, noise-compensated, MKE 45-1
Frequency response
Sensitivity
300–5,000 Hz
–
Max. sound pressure level
Min. terminating impedance
Output voltage
120 dB
150 Ω
400 mV 3 dB at 114 dB (as per RTCA/DO 214)
typ. 16 V DC (8–16 V DC, approx. 8–25 mA, as per RTCA/DO 214)
Supply voltage
30
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 350
ꢀ HMEC 352
ꢀ HMEC 356
ꢀ HMEC 450
General data
Connecting cable
1.5 m, unilateral
370 g
Weight without cable
Power supply for NoiseGard™
Current consumption
Fuse
12–35 V DC
27 mA (zero signal current), max. 80 mA
500 mA thermo fuse
Connectors
6.35 mm stereo jack plug ꢀ 6.35 mm stereo jack plug ꢀ 6-pin Redel plug for
ꢀ 6.35 mm stereo jack plug
for headphones,
PJ-068 jack plug for
microphone,
ꢀ for headphones,
ꢀ PJ-068 jack plug for
ꢀ microphone and
ꢀ NoiseGard™
ꢀ headphones, microphone ꢀ for headphones,
ꢀ and NoiseGard™
ꢀ
ꢀ
ꢀ PJ-068 jack plug for
ꢀ microphone,
XLR-3 for NoiseGard™
ꢀ XLR-3 for NoiseGard™
Controls
Mono/Stereo switch
On/off switch for NoiseGard™
Volume control for headphones
Temperature range
Operation
Storage
–15 °C ... +55 °C
–55 °C ... +55 °C
Operating time of battery pack
(except HMEC 352 and HMEC 356)
with batteries (four 1.5 V AA size alkaline-manganese batteries): approx. 15 hours
with NiMH rechargeable batteries: approx. 15 hours
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
HMEC 355
ꢀ HMEC 355-C
ꢀ HMEC 372
ꢀ HMDC 372
Headphones
Transducer principle
dynamic
Ear coupling
circumaural, closed
45–15,000 Hz
300/150 Ω, mono
> 25–40 dB
Frequency response
Nominal impedance active/passive
Attenuation (active and passive)
Max. sound pressure level
Contact pressure
ꢀ 50/35 Ω, mono
120 dB ( 5 %)
approx. 10 N
Microphone incl. preamplifier
Transducer principle
pre-polarized condenser mic capsule, noise-compensated, MKE 45-1
ꢀ dynamic mic capsule,
ꢀ noise-compensated,
ꢀ M-87/AIC
Frequency response
Sensitivity
300–5,000 Hz
ꢀ 500–4,000 Hz
–
ꢀ 1.8–4 µV / 74 dB at 5 Ω
Max. sound pressure level
Min. terminating impedance
Output voltage
120 dB
ꢀ –
ꢀ –
ꢀ –
ꢀ –
150 Ω
400 mV 3 dB at 114 dB (as per RTCA/DO 214)
typ. 16 V DC (8–16 V DC, approx. 8–25 mA, as per RTCA/DO 214)
Supply voltage
32
Download from Www.Somanuals.com. All Manuals Search And Download.
HMEC 355
ꢀ HMEC 355-C
ꢀ HMEC 372
ꢀ HMDC 372
General data
Connecting cable
1.5 m, unilateral
370 g
ꢀ coiled cable, unilateral
Weight without cable
Power supply for NoiseGard™
Current consumption
Fuse
12–35 V DC
27 mA (zero signal current), max. 80 mA
500 mA thermo fuse
Connectors
XLR-5 for headphones,
microphone and
NoiseGard™
ꢀ XLR-5 for headphones
ꢀ and microphone,
ꢀ XLR-3 for NoiseGard™
ꢀ U-174/U jack plug for headphones and microphone,
ꢀ XLR-3 for NoiseGard™
ꢀ
Controls
On/off switch for NoiseGard™
Volume control for headphones
Temperature range
Operation
Storage
–15 °C ... +55 °C
–55 °C ... +55 °C
Operating time of battery pack
(except HMEC 355)
with batteries (four 1.5 V AA size alkaline-manganese batteries): approx. 15 hours
with NiMH rechargeable batteries: approx. 15 hours
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Certificate of Conformity
Sennheiser electronic GmbH & Co. KG declare that these devices conform to the basic requirements of EEC
Directive 89/336/EEC and 73/23/EEC.
Guarantee Certificate
The guarantee period for this Sennheiser product is 5 years from the date of purchase. Excluded are accessory items,
rechargeable or disposable batteries that are delivered with the product; due to their characteristics these products have a
shorter service life that is principally dependent on the individual frequency of use.
The guarantee period starts from the date of original purchase. For this reason, we recommend that the sales receipt be
retained as proof of purchase. Without this proof (which is checked by the responsible Sennheiser service partner) you will
not be reimbursed for any repairs that are carried out.
Depending on our choice, guarantee service comprises, free of charge, the removal of material and manufacturing defects
through repair or replacement of either individual parts or the entire device. Inappropriate usage (e.g. operating faults,
mechanical damages, incorrect operating voltage), wear and tear, force majeure and defects which were known at the time
of purchase are excluded from guarantee claims. The guarantee is void if the product is manipulated by non-authorised
persons or repair stations.
In the case of a claim under the terms of this guarantee, send the device, including accessories and sales receipt, to the
responsible service partner. To minimise the risk of transport damage, we recommend that the original packaging is used.
Your legal rights against the seller, resulting from the contract of sale, are not affected by this guarantee.
The guarantee can be claimed in all countries outside the U.S. provided that no national law limits our terms of guarantee.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sennheiser electronic GmbH & Co. KG
30900 Wedemark, Germany
Phone +49 (5130) 600 0
Fax +49 (5130) 600 300
Printed in Germany
Publ. 04/05
512743 / A04
Download from Www.Somanuals.com. All Manuals Search And Download.
|