SY-6ZB
Motherboard
Quick Start Guide
Tested To Comply
C
With FCC Standards
FOR HOME OR OFFICE USE
FC
POST CONSUMER
RECYCLED PAPER
100%
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
1
Introduction
Congratulations on your purchase of the SY-6ZB Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-6ZB Motherboard User's Guide and
Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
When unpacking the Motherboard, check for the following items:
u
u
u
u
The SY-6ZB 82440 ZX AGP/PCI Motherboard
This Quick Start Guide
The Installation CD-ROM
SOYO 3-in-1 Bonus Pack CD-ROM (Norton AntiVirus,
Ghost and Virtual Drive)
u
u
u
u
The CPU Retention Set
One IDE Device Flat Cable
One Floppy Disk Drive Flat Cable
One dual 25-pin parallel with 25-pin flat cable and 9-pin
serial with 9-pin flat cable external connector
u
One dual 6-pin PS/2 mouse connector with 6-pin flat cable
and 9-pin serial connector with 9-pin flat cable
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
SY-6ZB Motherboard Layout
PS/2 Mouse
Connector
KB
Connector
1
1
1
Flash BIOS
ITE8671
AT Power
1
ATX Power
5
1
PRT 1
CPUFAN
1
4
JP50
COM 1
COM 2
FDC
1
5
IR1
9
USB
3
AGP Slot
JP44
WOL
Header
Slot 1
PCI Slot #3
PCI Slot #2
PCI Slot #1
TM
Intel
SB-LINK
ISA Slot #3
(PC-PCI)
82443 ZX
1
1
ISA Slot #2
ISA Slot #1
Intel
82371 EB
CMOS Clear
Jumper
3V Lithium
Battery
1
1
JP5
3
CHAFAN
IDE 2
IDE 1
+
_
Reset
Power
LED
DIMM 1
DIMM 2
Keylock
PWRBT
+
_
Turbo
LED
+
_
Speaker
+
_
HDD LED
SW1
Key Features
Ø
Supports Intel Pentium® III processor (450-
600MHz), Pentium® II processor (233-
450MHz) & CeleronTM processor (266-
433MHz)
Auto-detect CPU voltage
PC98, ACPI, Ultra DMA/33
Ø
Supports Creative SB-LINK ™ (PC-PCI)
for PCI audio card
1 x 32-bit AGP slot
3 x 32-bit bus mastering PCI slots
1 x IrDA port
Supports multiple-boot function
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Power-on by modem or alarm
Supports Wake-On-LAN (WOL)*
Supports Power-On by Keyboard*
Supports onboard hardware monitoring
and includes Hardware Doctor ™ utility
Ø
Ø
AT/ATX power connectors
Y2K Compliant
*Function is supported only when ATX power supply is used.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
2
Installation
To avoid damage to your Motherboard, follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted portion
of the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
Check the Motherboard for damage. If any chip appears loose, press carefully to seat
it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new SY-6ZB Motherboard. For detailed information, please refer to SY-
6ZB Motherboard User's guide and Technical Reference online manual included on the CD-
ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
u
u
u
u
u
u
u
u
u
u
u
Slot 1 processor with built-in CPU cooling fan (boxed type)
SDRAM module
Computer case and chassis with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device
VGA Card
Sound Card (optional)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive …
External Peripherals: Printer, Plotter, and Modem- (optional)
Internal Peripherals: Modem and LAN cards (optional)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Install the Motherboard
Follow the steps below in order to perform the installation of your new SY-6ZB Motherboard.
Step 1. Install the CPU
Mark your CPU Frequency: Record the working frequency of your CPU
that should be clearly marked on the CPU cover.
FSB 66MHz
266MHz (66 x 4.0)
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
FSB 100MHz
350MHz (100 x 3. 5)
400MHz (100 x 4.0)
450MHz (100 x 4.5)
500MHz (100 x 5.0)
550MHz (100 x 5.5)
600MHz (100 x 6.0)
CPU Mount Procedure: To mount the processor that you have purchased
separately, follow these instructions.
Retention Module
Step 1. Open the two sides by folding them up.
Step 2. Push the locks on top of the CPU Step 3. Insert the CPU into the retention
inward.
module. The CPU fits in the CPU slot in
only ONE way, do not try to force it in.
Step 4. After completely inserting the CPU, push the two locks on
top of the CPU outward. Now your CPU is ready for use.
To remove the CPU, press
the two notches on top of
the CPU inward. Now
press the two slides on the
retention module down and
remove the CPU.
Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation.
Failing to install these items may result in overheating and possible burn-out of your CPU.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Step 2. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan,
Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-6ZB
Motherboard, please refer to SY-6ZB Motherboard User's Guide and Technical Reference
online manual on CD-ROM.
Connectors and Plug-ins
PCI Audio Card Header: SB-Link ™(PC-PCI)
Wake-On-LAN Header: JP44
Connect the SB-Link ™(PC-PCI) cable from your
PCI audio card to this header.
Pin1
Pin2
Pin3
5VSB
GND
MP-Wakeup
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin1
GND
Pin2
12V
Pin3
SENSOR
Pin1
GND
Pin2
12V
Pin3
SENSOR
Key Lock
Power LED
Speaker
Power LED
Pin1 Pin2 Pin3
Keylock
_
_
Pin1
Control Pin
Pin2
GND
+
+
+
5V
NC GND
Speaker
_
_
+
Pin1
5V
Pin2
NC
Pin3
NC
Pin4
Speaker out
Reset
Turbo LED
HDD LED
PWRBT
HDD LED
Pin2
Turbo LED
PWRBT
Pin1
RESET
Pin1 Pin2
Pin1
Pin1
Pin2
Pin2
LED Anode LED Cathode LED Cathode GND Power On/Off GND Power Good GND
IrDA (Infrared Device Header): IR1
AT Power Cable
Pin1
VCC
Pin2
None
Pin3
IRRX
Pin4
GND
Pin5
IRTX
Connect the AT Power cable to this
connector. If you use AT power supply.
ATX Power On/Off: PWRBT
ATX Power Supply: ATX PW
Connect your power switch to this Attach the ATX Power cable to this connector.
header (momentary switch type).
Note: Please make sure the ATX power supply is able to
To turn off the system,
please press this switch and
hold down for longer than
4 seconds.
provide at least 720mA of current on the +5VSB lead if
you want to enable the advanced power management
functions, like Wake-On-LAN, Power-On by keyboard, etc.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Step 3. Configure Memory
Your board comes with two DIMM sockets, providing support for up to 256MB of main
memory using DIMM modules from 8MB to 128MB. For 66MHz front side bus CPUs use
12ns or faster memory; for 100MHz front side bus CPUs use 8ns (100MHz, PC100
compliant) memory.
Memory Configuration Table
Number of Memory Modules
DIMM 1
1st
DIMM 2
1
2
1st
2nd
RAM Type
Memory Module Size (MB)
SDRAM
8/16/32/64/128 Mbytes
Important: It is of prime importance that you install DIMM modules as outlined in the table
above in order to preserve signal integrity on 100MHz front side bus systems.
Step 4. Set SW1 for power up FSB clock and AGP bus clock.
SW1 is used to adjust AGP bus clock frequency depending on the value of the front side bus
(FSB) clock, also the setting of the SW1 determines the power up FSB clock which will
remain effective until the BIOS set the FSB clock to the CMOS setting.
SW1 Setting
Power up FSB Clock
66MHz
AGP Clock
AGP Clock
= FSB Clock ¸ 1
AGP Clock
= FSB Clock ¸ 1.5
100MHz
Note1: The factory default setting for SW1 (Power up FSB clock and AGP bus clock)
is 66MHz. CPUs that run on 100MHz may not boot at this frequency, so check
SW1 before booting for the first time.
Also, if the user changes the CPU, care should be taken to set SW1 in
accordance with the FSB Frequency of the new CPU.
Note2: The specification of maximum AGP bus Clock frequency is 66.6MHz.
*
*
*
Set SW1 to open when you use a FSB 100MHz CPU.
Set SW1 to close when you use a FSB 66MHz CPU.
Set SW1 to open when you use a FSB 66MHz CPU but want to over clock the FSB
clock to 100MHz via the BIOS setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Step 5. Set the CPU Frequency
You do not need to set any jumper for the CPU frequency. Instead, CPU setting are changed
through the BIOS [CHIPSET FEATURES SETUP]. Please refer to Chapter 3 - Quick BIOS
Setup for details on how to set the Slot 1 processor frequency.
Step 6. Enable/Disable Power-On by Keyboard (JP50)
You can choose to enable the Power-On by Keyboard function by shorting pin 2-3 on jumper
JP50, otherwise, short pin 1-2 to disable this function.
Power-On by
Keyboard
Enable
Disable
Short pin 2-3 to enable the
Short pin 1-2 to disable the
Power-On by Keyboard function. Power-On by Keyboard function.
JP50 Setting
1
2
3
1
2
3
Important: When using the Power-On by Keyboard function, please make sure the
ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to
meet the standard ATX specification.
Step 7. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5
seconds, and then by shorting pin 1-2 to retain new settings. This jumper can be easily
identified by its white colored cap.
CMOS Clearing
Clear CMOS Data
Retain CMOS Data
1
2
3
1
2
3
Short pin 2-3 for
at least 5 seconds
to clear the CMOS.
Short pin 1-2
to retain the
new settings.
JP5 Setting
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Note on Over-clocking Capability
The SY-6ZB Motherboard provides over-clocking capability. Due to the over-clocking
setting your system may fail to boot up or hang during run time. If this occurs, please perform
the following steps to recover your system from the abnormal situation:
1. Turn off system power (If you use a ATX power supply, sometimes you have to press
the power button for more then 4 seconds to shut down the system)
2. Set the SW1 to short if you use a FSB 66MHz CPU
3. Press and hold down the <Insert> key while turning on the system power. Keep
holding down the <Insert> key until you see the message of the CPU type and
frequency (133MHz or 200MHz) appear on screen
4. Press the <Del> key during the system diagnostic checks to enter the Award BIOS
Setup program
5. From the BIOS main menu, select [CHIPSET FEATURES SETUP] and move the
cursor to the [CPU Frequency] field to set the proper working frequency
6. Select [Save & Exit SETUP] and press <Enter> to save the configuration to the
CMOS memory, and continue the boot sequence
Note: SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
3 Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS [CHIPSET FEATURES SETUP].
After the hardware installation is complete, turn the power switch on, then press the <DEL> key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 3. Select [CHIPSET FEATURES SETUP]
Move the cursor to the [CPU Speed] field to set the CPU frequency.
Available [CPU Speed] settings on your SY-6ZB Motherboard are detailed in the following
table. If you set this field to [Manual], you are then required to fill in the next two consecutive
fields: (1) the [CPU Host Clock], and (2) the [CPU Ratio].
Select the working frequency of
your Pentium® III, Pentium® II,
CeleronÔ processor among these
preset values.
CPU Frequency
233MHz (66 x 3.5)
350MHz (100 x 3.5)
400MHz (100 x 4.0)
450MHz (100 x 4.5)
500MHz (100 x 5.0)
550MHz (100 x 5.5)
600MHz (100 x 6.0)
266MHz (66 x 4.0)
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
Note:
Mark the checkbox that
corresponds to the working
frequency of your Pentium® III,
Pentium® II, CeleronÔ processor in
case the CMOS configuration
should be lost.
Note: if you use Bus Frequencies of 75 MHz, make sure that your PCI cards can cope with
the higher PCI clock.
Step 4. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue the boot
sequence.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
4
The SOYO CD
The SOYO-CD will NOT autorun if you use it on an Operating System other
than Windows 9x or NT.
Your SY-6ZB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains (1) the user's manual file for your new Motherboard, (2) the drivers software
available for installation, and (3) a database in HTML format with information on SOYO
Motherboards and other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be shown as below.
(SOYO CD Start Up Program Menu)
If you use Windows 95/98, the SOYO CD Start Up Program automatically detects which
SOYO Motherboard you own and displays the corresponding model name.
Step 2. Read SOYO [6ZB] Manual
Click the Read Manual button to open the user's manual file of your Motherboard.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Please note that if the Start Up program was unable to determine which SOYO Motherboard
you own, the manual selection menu will pop up, as shown below. Then select the user's
manual file that corresponds to your Motherboard model name and click OK.
SOYO CD Manuals
Please select your manual in the box below
and click OK.
686 boards:
6ZB
586 boards:
OK
Back
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the Install Drivers button to display the list of drivers software that can be installed with
your Motherboard. The Start Up program displays the drivers available for the particular
model of Motherboard you own. We recommend that you only install those drivers.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
The following drivers are available for Windows 95
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel inf. Utility for Win 95
Intel BusMaster Drivers for Win NT
Intel BusMaster Drivers for Win95
Intel BusMaster Drivers for OS/2
Winbond hardware doctor for win 95/98
Winbond hardware doctor for win NT
Display all drivers
on the SOYO CD
Cancel
OK
(Driver Installation Menu)
The following drivers are available for Windows 98
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel BusMaster Drivers for Win NT
Intel BusMaster Drivers for OS/2
Winbond hardware doctor for win 95/98
Winbond hardware doctor for win NT
Display all drivers
on the SOYO CD
Cancel
OK
(Driver Installation Menu)
However, to display the list of all drivers software available with SOYO Motherboards, click
the Display all drivers on the SOYO CD button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
A short description of all available drivers follows:
Ø
Intel .inf utility for Win 95
Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX,
BX, ZX etc) this utility has to be run, it will update the necessary Windows .inf files. (Only for
Windows 95)
Ø
Ø
Ø
Intel Busmaster Drivers for Windows 95
Intel Busmaster Drivers for Win NT
Intel Busmaster Drivers for OS/2
These are the official busmaster drivers as supplied by Intel.
Note: Do NEVER install two types of busmaster drivers on your system, this will
lead to conflicts and system instability.
Ø
Winbond hardware doctor for Windows xx
Your motherboard comes with a hardware monitoring IC. By installing this utility Temperature,
Fan speed and Voltages can be monitored. It is also possible to set alarms when current
system values exceed or fall below pre-set values.
This utility comes with a preset monitoring rage for the CPU voltage. However, the core voltage
of the processor you purchased may fall out of this preset range, so you may need to adjust the
pre-set value. Please refer to the SY-6ZB Motherboard’s CD manual for the details.
Select which driver you want to install and click OK, or click Cancel to abort the driver
installation and return to the main menu.
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers require
to restart your system before they can become active.
Step 4. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to automatically find
the latest BIOS, manual and driver releases for your motherboard. This button will only work
if your computer is connected to the internet through a network or modem connection. Make
sure to get your modem connection up before clicking this button.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
Step 5. Enter the SOYO CD
Click the Enter SOYO CD button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available. For your convenience, this information is available in HTML format,
similar to the format widely used on the Internet.
Note: If no HTML browser is installed on your system, the Start Up program will prompt you
on whether or not you would like to install the Internet Explorer* browser. Click YES to install
the HTML browser. After the installation is complete, please restart your system. Then re-run
the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
How to contact us:
n
If you are interested in our products, please contact the SOYO sales
department in the region you live.
n
If you require Technical Assistance, please contact our Technical Support in
the region you live.
SOYO prefers Email as communication medium, remember to always add to the
email the country that you live in.
SOYO Taiwan
SOYO USA
41484 Christy Street, Fremont, CA
94538
No. 21 Wu-Kung 5 Rd., Hsin Chuang
City, Taipei Hsien, Taiwan
Region Covered: US and Canada
Region Covered: Taiwan and Asia-
Pacific. (Including Australia).
Web Site: www.soyo.com.tw
Sales:
Sales:
Tel: 510-226-7696
Fax: 510-226-9218
Email : [email protected]
Tel: 886-2-22903300-318
Fax: 886-2-22983322
E-mail: [email protected]
Technical Support:
Tel: 510-226-7696
Fax: 510-226-9218
Email : [email protected]
Technical Support:
Fax: 886-2-22983322
E-mail: [email protected]
SOYO Europe BV
SOYO (U.K.) LTD.
Signaalrood 19, 2718 SH Zoetermeer
The Netherlands
Unit 7, Alice Way, Hounslow Business
Park,
Hanworth Road, Hounslow, TW3 3UD
Region Covered: Europe except
Germany, Austria and Switserland
Region Covered: United Kingdom and
Republic of Ireland
europe.com
Web Site: www.soyo.co.uk
Sales:
Tel : +44 (0)181 569 4111
Fax: +44 (0)181 569 4134
E-mail: [email protected]
Sales:
Tel: +31-69-3637500
Fax: +31-79-3637575
Email: [email protected]
Technical Support:
Technical Support:
Tel : +44 (0)181 569 4111
Fax: +44 (0)181 569 4134
Tel : +31-79-3637500
Fax: +31-79-3637575
Email: [email protected]
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6ZB Quick Start Guide
E-Mail: [email protected]
Sales:
tel: 852-27109810
fax: 852-27109078
E-mail: [email protected]
SOYO Deutschland GmbH
August-Wilhelm-Kuhnholz-Str. 15
D-26135 Oldenburg
Technical Support:
tel: 852-27109810
fax: 852-27109078
E-mail: [email protected]
Region Covered: Germany, Austria
and Switzerland. (Zustandig fur
Deutschland, Osterreich, Schweiz)
SOYO China (Gin Mei Jei)
Vertrieb Mainboards, Notebooks und
SoyoCom Produkte:
E-Mail: [email protected]
Region Covered: All of China
Sales:
Tel: 86-10-62510089
fax: 86-10-62510388
E-mail: [email protected]
Fon: +49-(0)441/20910-31/33
Fax: +49-(0)441/203422
Technischer Support:
Technical Support:
E-Mail: [email protected]
Fon: +49-(0)441/20910-40
Fax: +49-(0)441/203422
Tel: 86-10-62510089
fax: 86-10-62510388
E-mail: [email protected]
SOYO KOREA
SOYO Japan
Region Covered: Korea
Region Covered: Japan
Web site: www.soyo.co.jp
Sales:
Tel : 82-2-716-2850
Fax : 82-2-704-2619
E-mail : [email protected]
Sales:
Tel: 81-3-33682188
Fax: 81-3-33682199
E-mail: [email protected]
Technical Support:
tel : 82-2-717-4392
Technical Support:
Tel: 81-3-33682188
fax : 82-2-712-5853
e-mail : [email protected]
Fax: 81-3-33682199
E-mail: [email protected]
SOYO Hong Kong
Region Covered: Hong Kong
Web Site: www.soyo.com.hk
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: August 1999
Version 1 .1
6ZB SERIAL
Download from Www.Somanuals.com. All Manuals Search And Download.
|