Sylvania TV DVD Combo SRDVC2019 User Manual

OWNER’S  
MANUAL  
19-INCH COLOR TV/DVD  
SRDVC2019  
TM  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
If you need additional assistance for set-up or operating  
after reading owner’s manual, please call  
TOLL FREE : 1-800-968-3429.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Please read before using this equipment  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
12.Power-Cord Protection-Power-supply cords should be  
routed so that they are not likely to be walked on or  
pinched by items placed upon or against them, paying par-  
ticular attention to cords at plugs, convenience receptacles,  
and the point where they exit from the appliance.  
19.Damage Requiring Service-Unplug this TV/DVD from  
the wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the  
TV/DVD.  
13.Outdoor Antenna grounding-If an outside antenna or  
cable system is connected to the TV/DVD, be sure the  
antenna or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect to  
proper grounding of the mast and supporting structure,  
grounding of the lead-in wire to an antenna discharge unit,  
size of grounding conductors, location of antenna-discharge  
unit, connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
c. If the TV/DVD has been exposed to rain or water.  
d. If the TV/DVD does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper adjust-  
ment of other controls may result in damage and will often  
require extensive work by a qualified technician to restore  
the TV/DVD to its normal operation.  
e. If the TV/DVD has been dropped or damaged in any way.  
f. When the TV/DVD exhibits a distinct change in perfor-  
mance-this indicates a need for service.  
14.Lightning-For added protection for this TV/DVD receiver  
during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall  
outlet and disconnect the antenna or cable system. This will  
prevent damage to the TV/DVD due to lightning and  
power-line surges.  
20.Replacement Parts-When replacement parts are required,  
be sure the service technician has used replacement parts  
specified by the manufacturer that have the same character-  
istics as the original part. Unauthorized substitutions may  
result in fire, electric shock, injury to persons or other haz-  
ards.  
15.Power Lines-An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from  
touching such power lines or circuits as contact with them  
might be fatal.  
21.Safety Check-Upon completion of any service or repairs to  
this TV/DVD, ask the service technician to perform routine  
safety checks to determine that the TV/DVD is in proper  
operating condition.  
22.Heat-This TV/DVD product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
16.Overloading-Do not overload wall outlets and extension  
cords as this can result in a risk of fire or electric shock.  
17.Object and Liquid Entry-Never push objects of any kind  
into this TV/DVD through openings as they may touch dan-  
gerous voltage points or short out parts that could result in  
a fire or electric shock. Never spill liquid of any kind on  
the TV/DVD.  
18.Servicing-Do not attempt to service this TV/DVD yourself  
as opening or removing covers may expose you to danger-  
ous voltage or other hazards. Refer all servicing to qualified  
service personnel.  
- 3 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRECAUTIONS  
LASER SAFETY  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public perfor-  
mance and lending of discs are prohibited.  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
RADIO-TV INTERFERENCE  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Cet appareil numérique de la classe B est con-  
forme à la norme NMB-003 du Canada.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
- 4 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION  
WARNING  
For safe operation and satisfactory performance of  
your TV/DVD, keep the following in mind when  
selecting a place for its installation:  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place,  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a TV/DVD  
which has moisture, it may damage the DVD and  
TV/DVD. Therefore when the condensation occurs  
inside the unit, turn the POWER button on and allow  
at least 2 hours for the unit to dry out.  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes  
at the top and bottom of the unit. Do not place the  
unit on a carpet because this will block the ventila-  
tion holes.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the TV/DVD near strong magnetic fields.  
Avoid moving TV/DVD to locations where temper-  
ature differences are extreme.  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If, by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
Do not put your fingers or objects into the  
TV/DVD disc loading tray.  
Do not place anything directly on top of the unit.  
A NOTE ABOUT RECYCLING  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-  
tions concerning chemical wastes.  
The serial number of this product may be found on the back of the unit. No other TV/DVD has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 5 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
PAUSING PLAYBACK OR DISPLAYING  
A STILL PICTURE . . . . . . . . . . . . . . . . . . . . .22  
C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2  
C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4  
RESUMING PLAYBACK FROM THE  
POINT WHERE PLAYBACK STOPPED . . . .22  
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF ELECTRICAL  
SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .5  
STEPPING THROUGH FRAMES . . . . . . . . . .22  
FAST FORWARD/REVERSE . . . . . . . . . . . . .23  
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . .23  
STARTING FROM A DESIRED TRACK . . . .23  
STARTING FROM A DESIRED TIME COUNT .23  
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .5  
C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .7  
C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .7  
C OPERATING CONTROLS AND FUNCTIONS 8  
PLAYING FROM A DESIRED TITLE OR  
CHAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
C PREPARATION FOR USE . . . . . . . . . . . . . . .10  
ANTENNA/CABLE CONNECTIONS . . . . . . .10  
INSTALLING THE BATTERIES . . . . . . . . . . .12  
RANDOM (Audio CD) . . . . . . . . . . . . . . . . . .24  
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24  
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . .25  
PROGRAM (Audio CD) . . . . . . . . . . . . . . . . .25  
CONNECTING TO EXTERNAL INPUT JACKS .12  
CONNECTING TO A STEREO SYSTEM (for DVD) .13  
C SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . .26  
CONNECTING TO AN AMPLIFIER  
EQUIPPED WITH DIGITAL INPUT JACKS,  
MD DECK OR DAT DECK (for DVD) . . . . . .13  
CHANGING THE AUDIO LANGUAGE OR  
SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . .26  
CHANGING THE SUBTITLE LANGUAGE . .27  
CONNECTING TO A DOLBY DIGITAL  
DECODER OR DTS DECODER (for DVD) . .14  
CHANGING THE CAMERA ANGLE  
(Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . .27  
TV SECTION  
C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .15  
CHANGING THE ON-SCREEN DISPLAY . . .28  
C CHANGING THE SETUP ITEMS . . . . . . . . .29  
LANGUAGE SETTINGS . . . . . . . . . . . . . . . .29  
VIDEO SETTINGS . . . . . . . . . . . . . . . . . . . . .30  
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . .30  
PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . .31  
OTHER SETTINGS . . . . . . . . . . . . . . . . . . . . .32  
LANGUAGE SELECTION . . . . . . . . . . . . . . .15  
CHANNEL PRESETTING . . . . . . . . . . . . . . .15  
C OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . .16  
WATCHING A TV PROGRAM . . . . . . . . . . . .16  
SELECTING THE SLEEP TIMER . . . . . . . . .16  
CLOSED CAPTION . . . . . . . . . . . . . . . . . . . .16  
PICTURE ADJUSTMENT . . . . . . . . . . . . . . . .17  
V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .18  
C LANGUAGE CODE LIST . . . . . . . . . . . . . . . .33  
C TROUBLESHOOTING GUIDE . . . . . . . . . . .34  
DVD SECTION  
C ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . .20  
C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .37  
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . .37  
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . .20  
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . .20  
SYMBOLS USED IN THIS MANUAL . . . . . .20  
C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .38  
C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover  
C PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . .21  
PLAYING A DVD VIDEO OR AN AUDIO CD .21  
USING THE DVD MENUS . . . . . . . . . . . . . . .21  
USING THE TITLE MENU . . . . . . . . . . . . . . .22  
- 6 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES  
TV  
DVD  
Tinted, Bright Black Matrix Picture Tube  
181 Channel SelectionAll VHF/UHF channels  
plus up to 125 cable channels.  
PLL Frequency Synthesized TuningThe latest  
PLL frequency synthesized electronic tuning sys-  
tem provides free and easy channel selection, and  
lets you tune directly to any channel using the  
channel number buttons (0~9 and +100-key) on the  
remote control.  
Dolby Digital soundThis player can handle  
Dolby Digital surround sound having 5.1 channels  
when connected to a Dolby Digital decoder.  
Still/fast/slow/step playbackVarious playback  
modes are available including still pictures, fast  
forward/reverse, slow motion and step frames.  
Random playback for audio CDThis player can  
shuffle the order of tracks to play them in random  
order.  
Program playback for audio CDYou can pro-  
gram the order of tracks to play them in any  
desired order.  
DVD menus in a desired languageYou can dis-  
play DVD menus in a desired language, if avail-  
able on a DVD.  
Screen saver and auto power-off functions–  
Screen saver is automatically activated when there  
is no input from the player or the remote control  
for one minute in stop mode. The power is auto-  
matically turned off when there is no input for 31  
minutes in still or stop mode.  
Subtitles in a desired languageYou can select a  
desired language for the display subtitles, if that  
language is available on a disc.  
Selecting a camera angleYou can select the  
desired camera angle, if a disc contains sequences  
recorded from different angles.  
Choices for audio language and sound mode–  
You can select the desired audio language and  
sound mode, if different languages and modes are  
available on a disc.  
On-Screen Function Display.  
Full-Function Remote Control  
Sleep Timer  
Closed Caption DecoderYou may view special-  
ly labeled (cc) TV programs, movies, news, prere-  
corded tapes, etc. with either a dialogue caption or  
text display added to the program.  
Auto Shut Off FunctionIf there is no air signal  
input from the antenna terminal and no operation  
for 15 minutes, the TV will turn itself off automati-  
cally.  
V-CHIPEnables parents to prevent their children  
from watching inappropriate material on TV.  
Parental lockYou can set the control level to  
limit playback of discs which may not be suitable  
for children.  
Automatic detection of discsThis player auto-  
matically detects if a loaded disc is DVD or audio  
CD.  
On-screen displayInformation about the current  
operation can be displayed on a TV screen, allow-  
ing you to confirm the currently active functions  
(such as program playback), on the TV screen  
using the remote control.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
2 AA Batteries  
PART NO. (N0285UD)  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-  
968-3429.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
- 7 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND FUNCTIONS  
- TV/DVD FRONT PANEL - [Fig. 1]  
volume  
channel  
stop  
skip  
play  
skip  
pause open/close  
power  
headphone  
video  
L-audio-R  
1 2  
3
4
5
6
7
8 18 10 18 12 13 14  
1.Disc loading tray  
- REMOTE CONTROL - [Fig. 2]  
2.VIDEO input (video) jackConnect to the video  
output jack of a video camera or VCR.  
3.AUDIO (audio) L/R input jacksConnect to the  
audio output jacks of a video camera or VCR.  
4.POWER (power) buttonPress to turn the power  
on and off.  
15  
36  
OPEN/  
POWER  
TV  
DVD  
CLOSE  
4
13  
1
4
2
5
8
0
3
6
5.VOLUME (volume) K/L buttonsPress to con-  
trol the volume level for the DVD and TV.  
6.CHANNEL (channel) K/L buttonsPress to  
select memorized channel.  
CH.  
6
16  
7
9
+100  
VOL.  
SLEEP  
5
7.Remote Sensor Window  
+10  
17  
18  
8.STOP (stop) buttonStops operation of the disc.  
9.REV buttonFast reverses playback to a desired  
point.  
10. PLAY (play) buttonStarts playback of the disc  
contents.  
11. FWD buttonFast forwards playback to a desired  
point.  
12. PAUSE (pause) buttonPauses the current disc  
operation.  
13. OPEN/CLOSE (open/close) buttonPress to  
insert discs into or remove them from the tray.  
14. HEADPHONE (headphone) jackTo connect  
headphone (not supplied) for personal listening.  
15. TV buttonPress to do TV operations.  
16. NUMBER button–  
SELECT  
SKIP  
MUTE  
35  
34  
SLOW  
FWD  
10  
9
PLAY  
STOP  
REV  
11  
8
33  
32  
31  
30  
PAUSE  
MODE  
SETUP  
MENU  
12  
19  
20  
21  
22  
ENTER  
TITLE  
RETURN  
CLEAR SEARCH MODE REPEAT  
A-B  
29  
28  
27  
26  
DISPLAY AUDIO  
SUBTITLE  
ANGLE  
23  
24  
25  
TV Mode:  
Press two digits to directly access the desired  
channel.  
Remember to press a "0" before a single digit  
channel.  
+100 button–  
Press to select cable channels which are equal or  
greater than number 100.  
To use as TV remote control, press the TV but-  
ton on the remote control after TV mode is  
selected. TV operation buttons have been indi-  
cated by blue or white.  
To use as DVD remote control, press the DVD  
button on the remote control after DVD mode is  
selected. DVD operation buttons have been  
indicated by yellow or white.  
DVD Mode:  
Press to enter the desired number.  
- 8 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
- REAR VIEW - [Fig. 3]  
ANT.  
DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
AUDIO OUT  
COAXIAL  
R
L
37  
38 39  
40  
30. RETURN buttonReturns to the previous opera-  
+10 button–  
tion.  
Press to enter the desired numbers which are  
equal or greater than number 10.  
31. ENTER buttonPress to accept a setting.  
17. SLEEP buttonPress the SLEEP button to dis-  
play the sleep timer and start the function. The  
shut off time can be determined by the number of  
times you press the button. (0, 10, 20, 30,..90, 0  
minutes)  
32. Arrow buttons–  
TV Mode:  
Press to select a setting mode from the menu on  
the TV screen.  
Press to select or adjust from a particular menu.  
18. SKIP (skip) buttonsSkip chapters or tracks to a  
DVD Mode:  
desired point.  
Use when making settings while watching the dis-  
play on a TV screen.  
19. MODE buttonActivates program playback or  
random playback mode.  
33. MENU buttonDisplays the DVD and TV menus.  
20. SETUP buttonPress to enter the setup mode or  
34. SELECT buttonPress to change of TV mode,  
to change setup items.  
external input mode or DVD mode.  
21. TITLE buttonDisplays the title menu.  
35. MUTE buttonPress the MUTE button to turn off  
the sound portion of the TV program. (Volume  
level display turns LIGHT RED from LIGHT  
BLUE.) Press the MUTE button again or press  
the VOL(ume) K or L button to restore sound.  
22. CLEAR buttonResets a setting.  
23. DISPLAY button–  
TV Mode:  
Press to display the channel number on the  
screen. If you press it again, the channel number  
will disappear.  
36. DVD buttonPress to do DVD operations.  
37. Power cordConnect to a standard AC outlet  
(120V/60Hz).  
DVD Mode:  
NOTE: Remove the power cord from the hook to  
avoid breaking a wire before you connect to a  
standard AC outlet.  
Displays the current status on the TV screen for  
checking purposes.  
24. SEARCH MODE buttonPress to locate a  
desired point.  
38. COAXIAL digital audio out jackConnect to the  
other amplifier or decoder.  
25. AUDIO buttonPress to select a desired audio  
language or sound mode.  
39. AUDIO L/R output jackConnect to the other  
amplifier or decoder.  
26. SUBTITLE buttonPress to select a desired sub-  
title language.  
40. ANT. in jackConnect to an antenna, cable sys-  
tem, or satellite system.  
27. REPEAT buttonRepeats playback of the cur-  
rent disc, title, chapter or track.  
28. ANGLE buttonPress to change the camera  
angle to see the sequence being played back from  
a different angle.  
29. A-B REPEAT buttonRepeats playback of a  
selected section.  
- 9 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
VHF/UHF COMBINED ANTENNA  
The VHF/UHF Rod Antenna (supplied) is detachable. Insert the stem of the antenna into the hole on the upper-  
back portion of the TV/DVD. Connect the VHF/UHF Rod Antenna or VHF/UHF Combination Antenna to the  
ANT. terminal of the TV/DVD as shown in the diagram below. For the best reception, fully extend the  
VHF/UHF Rod Antenna and make the necessary adjustments. (Avoid touching the top section when adjusting.)  
NOTE:  
Before plugging the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent, straighten  
the pin as illustrated, then plug the pin into antenna terminal.  
Bent pin  
Cable Plug  
(Straight pin)  
(Needs to be straightened)  
VHF/UHF Antenna  
(Not supplied)  
Rod Antenna  
(Supplied)  
ANT.  
[Fig. 4]  
NOTE:  
The connection of an indoor antenna may not always give acceptable TV reception.  
VHF/UHF SEPARATE ANTENNAS  
In some areas it will be necessary to use an outdoor antenna.  
VHF Antenna (Not supplied)  
UHF Antenna  
(Not supplied)  
VHF/UHF  
Combiner  
(Not  
supplied)  
ANT.  
Flat twin-lead cable  
[Fig. 5]  
EN  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
0C28  
CABLE WITHOUT CONVERTER/  
DESCRAMBLER BOX  
Use this connection if your cable system connects directly to your TV/DVD without a converter box.  
From Cable System  
75-ohm Coaxial  
Cable (Not  
supplied)  
ANT.  
[Fig. 6]  
CABLE WITH CONVERTER/  
DESCRAMBLER BOX OR SATELLITE BOX  
If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic  
connection shown here.  
Satellite Box or  
Cable Box (Not supplied)  
OUT  
IN  
From Cable System  
or Satellite Dish  
75-ohm Coaxial  
Cable  
(Not supplied)  
ANT.  
[Fig. 7]  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connect-  
ed to the grounding system of the building as close to the point of cable entry as practical.  
- 11 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING THE BATTERIES  
1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.  
2)Insert 2 "AA" penlight batteries into the battery compartment in the direction indicated by the polarity (+/-)  
markings.  
3)Replace the cover.  
CONNECTING TO EXTERNAL INPUT JACKS  
When you watch a program recorded on an another source (VCR or video camera), use the audio/video input  
jacks on the front of the TV/DVD.  
Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this TV/DVD.  
Then press the SELECT button until "VIDEO" appears on the screen.  
NOTE:  
When you connect a monaural VCR (another source) to this TV/DVD, connect the Audio output jack of the  
monaural VCR (another source) to the AUDIO L jack of this TV/DVD. The audio will output in both L and  
R channel equally.  
To the audio  
output jacks  
[Another source]  
Audio/Video  
coaxial cable  
(not supplied)  
video  
L-audio-R  
etc.  
To the video  
output jack  
[Front of the TV/DVD]  
[Fig. 8]  
- 12 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A STEREO SYSTEM (for DVD)  
DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
AUDIO OUT  
COAXIAL  
R
L
Stereo system  
To Right (red) and Left (white)  
AUDIO OUT jacks  
(only DVD AUDIO OUT)  
To ANALOG AUDIO INPUT jacks  
[Fig. 9]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the  
TV/DVD.  
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL  
INPUT JACKS, MD DECK OR DAT DECK (for DVD)  
Use audio coaxial digital cables (commercially available) for the audio connections.  
DIGITAL AUDIO  
OUT AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL  
R
L
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
Amplifier equipped with digital  
input jacks, MD deck,  
DAT deck, etc.  
(only DVD AUDIO OUT)  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
[Fig. 10]  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.  
Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD using  
incorrect settings may generate noise distortion, and may also damage the speakers.  
When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and  
you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.  
- 13 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING TO A DOLBY DIGITAL DECODER  
OR DTS DECODER (for DVD)  
If using this TV/DVD to play back a TV/DVD in a 5.1 channel Dolby Digital surround or DTS surround for-  
mat, the TV/DVD outputs a Dolby Digital or DTS data stream from its COAXIAL digital audio out jack. By  
hooking the player up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic ambi-  
ence with powerful and high-quality surround sound of a professional standard such as can be heard in movie  
theaters.  
Use audio coaxial digital cables (commercially available) for the audio connections.  
Center  
speaker  
Front speaker  
(left)  
Front speaker  
(right)  
DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
AUDIO OUT  
COAXIAL  
R
L
Dolby Digital  
or DTS decoder  
To DIGITAL AUDIO OUT  
(PCM/BITSTREAM)  
COAXIAL jack  
To COAXIAL DIGITAL  
AUDIO INPUT jack  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
[Fig. 11]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner's Manuals for the components to be connected to the TV/DVD.  
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.  
If connected to a DTS decoder, set DTS to ON for audio output in the setup mode.  
Unless connected to a Dolby Digital decoder or a DTS decoder, set DOLBY DIGITAL and DTS to OFF for  
audio output in the setup mode. Playing a TV/DVD using incorrect settings may generate noise distortion,  
and may also damage the speakers.  
When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and  
you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.  
Manufactured under license from Dolby  
Laboratories. Dolbyand the double-D  
symbol are trademarks of Dolby  
Laboratories. Confidential Unpublished  
Works. ©1992-1997 Dolby Laboratories, Inc.  
All rights reserved.  
DTSand DTS Digital Outare trademarks of  
Digital Theater Systems, Inc.  
- 14 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV SECTION  
SET UP FOR USE  
Getting started  
2
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
1
Press the Arrow K or L button to  
point to "CHANNEL SET". Then,  
press the Arrow B button.  
Connect the power cord to a standard AC outlet.  
NOTE: If some digits appear in the corner of the  
screen, press the POWER button without unplugging  
the power cord.  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [OFF]  
3
Press the Arrow K or L button to  
point to "AUTO MEMO". Then,  
press the Arrow B button.  
2
ADD/DELETE  
AUTO MEMO  
Press the POWER button to turn on the TV/DVD.  
The tuner scans and memorizes all  
active channels in your area.  
3
Press the SELECT button on the remote control until  
channel number or "TV" appears on the screen.  
Then press the TV button.  
The TV distinguishes between standard TV chan-  
nels and cable channels.  
When AUTO MEMO action is completed, the low-  
est memorized channel reappears on the screen.  
When you press the Arrow K or L button after  
selecting AUTO MEMO, the tuner will stop at the  
memorized channels only.  
LANGUAGE SELECTION  
If you want to change the language of the on-screen  
menu, follow the procedure below.  
The TV may recognize TV channels to be CATV  
channels by the receiving conditions. In this case,  
try AUTO MEMO action again in the fine receiv-  
ing conditions.  
1
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
Press the MENU button so that the  
ESPAÑOL  
menu display appears on the TV  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [OFF]  
screen.  
[ADD/DELETE FUNCTION]  
1)Press the MENU button so that the menu display  
appears on the TV screen.  
2)Press the Arrow K or L button to point to "CHAN-  
NEL SET". Then, press the Arrow B button.  
2
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
Press the Arrow K or L button to  
point to "LANGUAGE".  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [OFF]  
3)Press the Arrow B button so that  
"ADD/DELETE" is selected.  
4)Use the Arrow K or L button to  
select the channel you wish to  
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
3
V-CHIP SET UP  
CAPTION [OFF]  
put into memory or to erase from  
Select "ENGLISH", "ESPAÑOL" = Spanish or  
"FRANÇAIS" = French by using the Arrow B or s  
button.  
memory.  
NOTE: The display will return to the screen in  
about 10 seconds. Perform "ADD/DELETE" func-  
tion while this display appears on the screen.  
4
Press the Arrow B or s button  
to light up the channel number in  
LIGHT BLUE if you wish to  
Press the MENU button to exit the menu.  
NOTE: An on-screen display language must be  
selected each for the TV mode and DVD mode.  
ADD/DELETE  
AUTO MEMO  
add the channel into memory.  
Press the Arrow B or s button  
CHANNEL PRESETTING  
To preset a channel or to change a preset channel,  
follow the procedure below.  
to light up the channel number in LIGHT RED if  
you wish to erase the channel from memory.  
5)Press the MENU button to exit the menu.  
1
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
Press the MENU button so that the  
menu display appears on the TV  
screen.  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [OFF]  
- 15 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATIONS  
WATCHING A TV PROGRAM  
CLOSED CAPTION  
This TV can receive C1 and C2 of Caption and Text.  
1
CAPTION MODE  
Select the desired channel with the CH(annel) K or  
1)Characters can be displayed on the TV screen when  
the received broadcast signal contains the Caption  
Signals.  
2)Paint-on mode: Displays input characters on the  
screen immediately.  
L button.  
2
Adjust the volume to the desired listening level using  
the VOL(ume) K or L button.  
Pop-on mode: Once characters are stored in mem-  
ory, it is displayed all at once.  
3
Roll-up mode: Displays the characters continuous-  
ly by scrolling (max. 4 lines)  
Adjust picture controls for a natural looking image.  
(See "PICTURE ADJUSTMENT".)  
NOTE: If the CAPTION C1 or C2 is selected but the  
caption signal is not included, characters will not be  
displayed.  
SELECTING THE SLEEP TIMER  
TEXT MODE  
1)Displays the text on the screen by scrolling (max. 7  
lines)  
2)If the received broadcast signal does not contain  
the caption or text signal, no change will occur.  
NOTES:  
1)When your TV receives a special effects playback  
signal (i.e., Search, Slow, Still) from a VCR’s  
video output channel (CH3 or CH4), your TV may  
not display the correct caption or text.  
2)Captions and texts may not match the TV voice  
exactly.  
3)Interference may cause the closed caption system  
not to function properly.  
4)The caption or text characters will not be displayed  
while the menu display or function’s display is  
shown.  
The sleep timer function enables you to shut off the  
power without pressing the POWER button after a  
desired time period.  
1
Press the SLEEP button on the remote control.  
2
You may change the sleep time  
with pressing the SLEEP button on  
the remote control repeatedly. The  
SLEEP 10  
timer is set up to 90 minutes, 10  
minutes each time the SLEEP button is pushed. (The  
timer display counts up and sleep timer will be dis-  
played on the screen when you press the SLEEP but-  
ton on remote control.)  
5)If you see this screen!!  
To cancel the sleep timer:  
Press the SLEEP button repeatedly until "SLEEP 0"  
is displayed.  
NOTES:  
If your TV displays a black box on the screen, this  
means that your TV is set to TEXT mode. To clear  
screen, select CAPTION C1, C2 or CAPTION  
[OFF].  
When you disconnect the unit from the AC outlet,  
or if you have a power failure, the sleep time will  
be lost.  
When the TV mode is changed to the DVD mode,  
the sleep time will be lost.  
- 16 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GAME MODE  
Set to the most suitable position for TV GAME.  
CLOSED CAPTION SELECTION  
You may view specially labeled (cc) TV programs,  
movies, news, prerecorded tapes, etc. with either a  
dialogue caption or text display added to the pro-  
gram.  
[B] : ON  
[s] : OFF  
BRIGHT  
Adjust until the whitest parts of the picture are as  
bright as you prefer.  
1
[B] : increase brightness  
[s] : decrease brightness  
Press the MENU button so that the menu display  
appears on the TV screen.  
CONTRAST  
Adjust to increase or decrease contrast.  
2
[B] : increase contrast  
[s] : decrease contrast  
COLOR  
Press the Arrow K or L button to point to "CAP-  
TION".  
Adjust to be brilliant or pale color.  
3
[B] : be brilliant color  
[s] : be pale color  
Press the Arrow B or s button to select the mode  
you wish.  
TINT  
Adjust to obtain natural skin tones.  
[B] : greenish tone  
[s] : reddish tone  
4
When done, press the MENU button to exit the  
menu.  
NOTES:  
B or s  
: Press the Arrow  
button.  
In the above steps, the picture adjustment display  
will disappear from the TV screen after about 10  
seconds unless you press any buttons, even though  
you may not be finished. Press the MENU and  
Arrow B button so that "PICTURE" mode is  
selected. Then, press the Arrow K or L button  
repeatedly until the display returns to the screen.  
PICTURE  
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [OFF]  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [ C1]  
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [ C2]  
If you adjust the other Picture control after you set  
the Game mode to [ON], the Game mode is set to  
[OFF] automatically. If you want to set the Game  
mode, reset it to [ON].  
PICTURE  
PICTURE  
: Press the Arrow L or L button.  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
CHANNEL SET  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [ T2]  
FRANÇAIS  
V-CHIP SET UP  
CAPTION [ T1]  
[
]
[
]
[
[
[
]
]
]
[
[
[
]
]
]
GAME MODE  
BRIGHT  
CONTRAST  
COLOR  
OFF  
ON  
PICTURE ADJUSTMENT  
1
Press the MENU button so that the menu display  
appears on the TV screen.  
2
Press the Arrow B button so that "PICTURE" mode  
is selected.  
[
]
[
]
TINT  
3
Select the feature you wish to adjust with the Arrow  
K or L button and adjust it with the Arrow B or s  
button.  
- 17 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
<Selection> <Rating Category Explanations>  
V-CHIP SET UP  
• G:  
General Audience  
V-CHIP enables parents to prevent their children  
from watching inappropriate material on TV.  
V-CHIP reads the ratings for programming (except  
for news and sports programs, unedited movies on  
premium cable channels, and Emergency Broadcast  
System signals), then denies access to programming  
if the program's rating meets the limitations you  
select. In this case, "PROTECTED PROGRAM by  
..." message appears on the TV screen.  
• PG:  
• PG-13:  
• R:  
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires  
accompanying parent or adult  
guardian  
No one under 17 admitted  
Mature audience only  
• NC-17:  
• X:  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
To block ratings, follow the steps below.  
Programming may be rated by the Motion Picture  
Association of America (MPAA) or according to  
the Television Parental Guidelines. In order to  
block any inappropriate programming, set your  
limits in both places (MPAA RATING and TV  
RATING).  
When you turn "G" to [BLOCK] or [VIEW], the  
all ratings will turn to [BLOCK] or [VIEW] auto-  
matically.  
When you turn "X" to [VIEW], the all ratings will  
turn to [VIEW] automatically.  
You cannot access the menu when the "PROTECT-  
ED PROGRAM by ..." message appears. In this  
case, change to the unblocked channel, then press  
the MENU button.  
5
Press the MENU button to exit the menu.  
[MPAA RATING SET UP]  
[TV RATING SET UP]  
1
1
Press the MENU button so that the menu display  
appears on the TV screen.  
Press the MENU button so that the menu display  
appears on the TV screen.  
2
2
PICTURE  
CHANNEL SET  
LANGUAGE [ENGLISH]  
PICTURE  
Press the Arrow K or L button to  
point to "V-CHIP SET UP". Then,  
press the Arrow B button.  
CHANNEL SET  
Press the Arrow K or L button to  
LANGUAGE [ENGLISH]  
ESPAÑOL  
FRANÇAIS  
ESPAÑOL  
FRANÇAIS  
point to "V-CHIP SET UP". Then,  
press the Arrow B button.  
V-CHIP SET UP  
CAPTION [OFF]  
V-CHIP SET UP  
CAPTION [OFF]  
3
3
TV RATING  
MPAA RATING  
Press the Arrow K or L button to  
TV RATING  
Press the Arrow K or L button to  
MPAA RATING  
point to "TV RATING". Then,  
press the Arrow B button.  
point to "MPAA RATING". Then,  
press the Arrow B button.  
4
4
G
[VIEW]  
[VIEW]  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
TV-Y  
TV-Y7  
TV-G  
TV-PG (  
TV-14  
TV-MA (  
[VIEW]  
) [VIEW]  
[VIEW]  
) [VIEW]  
) [VIEW]  
) [VIEW]  
Press the Arrow K or L button to  
point to your desired item.  
Then, press the Arrow B button to  
select [BLOCK] or [VIEW].  
PG  
PG-13  
R
NC-17  
X
Press the Arrow K or L button to  
point to your desired item. Then,  
press the Arrow B button to select  
[BLOCK] or [VIEW].  
(
(
- 18 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
<Selection> <Rating Category Explanations>  
• TV-Y:  
• TV-Y7:  
Appropriate for all children  
Appropriate for children seven and  
older  
• TV-G:  
General Audience  
• TV-PG:  
• TV-14:  
• TV-MA:  
Parental Guidance suggested.  
Unsuitable for children under 14  
Mature audience only  
When you select the rating category and turn it  
[BLOCK], the higher rating will turn [BLOCK]  
automatically. Also, the lower rating will turn  
[VIEW] automatically.  
When you turn "TV-Y" to [BLOCK] or [VIEW],  
the all ratings will turn to [BLOCK] or [VIEW]  
automatically.  
When you turn "TV-MA" to [VIEW], the all rat-  
ings will turn to [VIEW] automatically.  
When you select TV-Y7, TV-PG, TV-14, or TV-MA  
and you press the Arrow B button, the sub-ratings  
will appear on the TV screen.  
If you select the rating category (example: TV-PG)  
and turn it [BLOCK] or [VIEW], the sub-ratings  
(example: V for Violence) will turn [BLOCK] or  
[VIEW] automatically.  
You can set the sub-ratings to [BLOCK] or [VIEW]  
individually when the rating category is set to  
[BLOCK]. To set the sub-ratings individually, follow  
the steps below.  
TV-Y7  
[BLOCK]  
When you select [TV-Y7]:  
Press the Arrow K or L button  
to select "FV" (Fantasy  
FV  
[BLOCK]  
Violence). Then, press the Arrow  
B button to select [BLOCK] or  
[VIEW].  
When you select [TV-PG],  
[TV-14] or [TV-MA]:  
TV-PG  
[BLOCK]  
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
Press the Arrow K or L button  
to select "D"(Suggestive  
Dialog), "L"(Coarse Language),  
"S"(Sexual Situation), or  
"V"(Violence). Then, press the  
TV-Y  
TV-Y7  
TV-G  
TV-PG (DLSV)[BLOCK]  
TV-14 (DLSV)[BLOCK]  
TV-MA ( LSV)[BLOCK]  
[VIEW]  
)[VIEW]  
[BLOCK]  
(
Arrow B button to select [BLOCK] or [VIEW].  
NOTE: When you select [TV-MA], "D" does not  
appear on the TV screen.  
The sub-ratings which set to [BLOCK] appears  
next to the rating category in the TV RATING  
menu.  
5
Press the MENU button to exit the menu.  
- 19 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD SECTION  
ABOUT THE DISCS  
Photo CD  
PLAYABLE DISCS  
The following discs can be played back on this  
TV/DVD.  
(Never play back, otherwise malfunction may  
result.)  
Video CD  
(Never play back, otherwise malfunction may  
result.)  
Maximum  
Playback Time  
Disc Type  
Logo  
Contents Disc Size  
Approx. 4 h  
(single-sided)  
Approx. 8 h  
Any other discs without compatibility indications  
12 cm  
Sound  
and  
Pictures  
(double-sided)  
DVD  
Video  
DISC TYPES  
Approx. 80 min  
(single-sided)  
Approx. 160 min  
(double-sided)  
8 cm  
[DVD]  
Data on a DVD is divided into sections called  
"titles", and then into subsections called "chapters",  
each of which is given a title or chapter number.  
Playback conditions are preset on some DVD video  
discs, and these playback conditions take priority  
over user operations on this player. If a function you  
selected do not run as desired, refer to the manual  
accompanying the disc.  
12 cm  
74 min  
Audio  
CD  
Sound  
8 cm  
20 min  
(singles)  
This player conforms to the NTSC color system. You  
cannot play discs recorded in other color systems  
such as PAL or SECAM.  
Some discs include region codes as shown below.  
Example  
Title 1  
Title 2  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2  
The number inside the symbol refers to a region of  
the world, and a disc encoded in a specific region  
format can only be played back on TV/DVD with  
the same region code.  
[AUDIO CD]  
Data on an audio CD is divided into sections called  
"tracks", each of which is given a track number.  
The following discs cannot be played back on this  
TV/DVD.  
DVD with region codes other than 1 or ALL.  
DVD-ROM  
Example  
DVD-R/DVD-RAM  
Track 1  
Track 2  
Track 3  
Track 4  
Track 5  
Track 6  
(Never play back, otherwise malfunction may  
result.)  
CD-ROM  
VSD  
CDV  
(Only plays back the audio part.)  
CD-G  
SYMBOLS USED IN THIS MANUAL  
The following symbols appear below some head-  
ings and in some notes in this manual, with the  
following meanings.  
(Only plays back the sound.)  
CD-R  
(Never play back, otherwise malfunction may  
result.)  
DVD  
:
CD-I  
Description refers to playback of DVD video discs.  
CD  
Description refers to playback of audio CDs.  
(Never play back, otherwise malfunction may  
result.)  
:
- 20 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING A DISC  
NOTES:  
Getting started  
A "prohibited icon" may appear  
at the bottom right on the TV  
1
Turn on the power of amplifier and any other compo-  
nents which are connected to the TV/DVD. (Change  
the input system to suit the TV/DVD, and check that  
the sound volume is correct.)  
screen during operation, warning  
that a prohibited operation has  
been encountered by the  
TV/DVD or the disc.  
If a disc is dirty or has scratches, the pictures may  
appear distorted and the playback operation may  
stop. In such cases, clean the disc and unplug the  
power cord and then plug it again before resuming  
playback.  
With DVDs that use some titles for playback pro-  
gram signals, playback may start from the second  
title, or it may skip these titles.  
2 Press the POWER button.  
The power will turn on.  
3 Press the SELECT button on the remote con-  
trol until "DVD" appears on the screen.  
Then press the DVD button.  
The DVD functions are active only in the DVD  
mode.  
To run the DVD player, press the PLAY or  
OPEN/CLOSE button.  
PLAYING A DVD VIDEO  
OR AN AUDIO CD  
DVD  
CD  
USING THE DVD MENUS  
1 Press the OPEN/CLOSE button.  
The disc loading tray will open.  
DVD  
2 Place a disc into the tray.  
Make sure the disc is sitting properly in the correct  
recess, with the label side up.  
Some DVDs contain their own menus, such as a  
guidance menu which describes the contents of the  
disc or a selection menu for sound, language and  
other customized settings.  
1 Press the MENU button.  
The DVD menu will appear.  
2 Select the desired title.  
Press the Arrow buttons (L/K/B/s) to change the  
setting, and then press the ENTER button.  
3 Press the PLAY button.  
3 Playback will start from the selected title.  
The tray will close automatically, and playback  
will then start from the first chapter or track of the  
disc. You need to press the PLAY button only when  
the tray has been closed by pressing the  
OPEN/CLOSE button.  
When you play back the DVD which a title menu  
is recorded, the menu may appear on the screen. In  
this case, refer to "USING THE TITLE MENU".  
4 Press the STOP button to stop play.  
- 21 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RESUMING PLAYBACK FROM  
THE POINT WHERE  
USING THE TITLE MENU  
DVD  
PLAYBACK STOPPED  
DVD  
With a DVD containing a title menu, you can select  
desired titles from the menu.  
1 Press the STOP button during playback.  
Playback will stop, and "STOP"  
1 Press the TITLE button.  
The title menu will appear.  
MEMO ON  
will appear at the top-right of the  
screen and then "MEMO ON" at  
the top-left.  
2 Select the desired title.  
Press the Arrow buttons (L/K/B/s) to change the  
setting, and then press the ENTER button.  
2 Press the PLAY button. Playback will start  
CALLING UP A MENU SCREEN DUR-  
ING PLAYBACK  
from the point where the previous playback  
session was stopped.  
PLAY  
For DVDs  
Press the MENU button to call up the DVD menu.  
Press the TITLE button to call up the title menu.  
NOTE:  
NOTES:  
Contents of menus and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
The resume function can be reset by pressing the  
STOP button twice or by opening the disc loading  
tray.  
The resume function is not available with audio  
CDs.  
PAUSING PLAYBACK OR  
DISPLAYING A STILL PICTURE  
STEPPING THROUGH FRAMES  
DVD  
CD  
DVD  
1 Press the PAUSE button during playback.  
Playback will pause, with sound  
muted.  
PAUSE  
1 Press the PAUSE button while playback is  
paused.  
PAUSE  
The next picture frame is dis-  
played with sound muted each  
time the button is pressed.  
2 Press the PLAY button to resume playback.  
PLAY  
2 Press the PLAY button to resume playback.  
PLAY  
- 22 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAST FORWARD/REVERSE  
1 Press the number buttons to enter the desired  
track number.  
The selected track will be located, and playback  
will start.  
DVD  
CD  
You can also press the SEARCH MODE button, use  
the number or K/L buttons to enter the track number,  
1 Press the FWD g or REV h button during  
playback. (The sound for DVD is muted.)  
and then press the PLAY button.  
Pressing the SEARCH MODE but-  
ton during playback causes the cur-  
rent track number to be displayed in  
square brackets.  
For DVDs, pressing the FWD g or REV h  
button cycles the playback speed in three steps.  
For audio CDs, the playback speed is fixed.  
SEARCH/TRACK  
TOTAL TRACKS: 07  
TRACK  
Start  
[
6 ]  
_
E
REV  
Button  
FWD D  
Button  
Ex2  
Dx2  
Exit  
Ex8  
Dx8  
TRICKS WITH THE SKIP BUTTONS (H, G)  
If the SKIP button G is pressed during playback  
or while playback is paused, the current track is  
skipped and the next track is played. When the  
SKIP button H is pressed once, the top of the cur-  
rent track is located for replaying. When the SKIP  
button H is pressed again while playback is  
paused, the previous track is located. Each time the  
SKIP button H is pressed while playback is  
paused, the disc is searched backward track by  
track. Once playback has started, pressing the SKIP  
button H locates the top of the current track.  
Ex32  
Dx32  
2 Press the PLAY button to return to normal  
playback speed.  
SLOW MOTION  
DVD  
STARTING FROM A DESIRED  
TIME COUNT  
1 Press the FWD g button while playback is  
paused. (Sound remains muted.)  
Slow motion mode will be activated.  
Pressing the FWD g button cycles the playback  
speed in three steps. Select an appropriate speed  
while referring to the speed indication on the  
screen.  
DVD  
CD  
1 Press the SEARCH MODE  
SEARCH/TIME  
button.  
TOTAL TIME 1h23m45s  
TIME [ _h__m__s ]  
Press the button three times for  
DVDs or two times for audio  
CDs.  
FWD D  
Button  
1/16  
Start  
Exit  
1/8  
2 Press the number buttons to set the desired  
time count.  
SEARCH/TIME  
1/2  
Example: 1 hour, 23 minutes and  
30 seconds  
1+10+103→  
+10+10+100  
To enter 0 (zero), press the num-  
ber 0 (zero) button or press the B button.  
TOTAL TIME: 1h23m45s  
TIME [1h23m30s]  
_
Start  
Exit  
2 Press the PLAY button to return to normal  
playback speed.  
NOTES:  
3 Press the PLAY button. Playback will then  
Slow playback is not available with audio CDs.  
start from the set time count.  
The reverse of slow playback is not available.  
NOTES:  
Playback from a desired time count is not available  
with some discs.  
Specific time playback is not available with some  
discs or if the unit is in stop mode.  
STARTING FROM A DESIRED  
TRACK  
CD  
- 23 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAYING FROM A DESIRED  
TITLE OR CHAPTER  
REPEAT  
DVD  
CD  
DVD  
1 Press the REPEAT button.  
For DVDs  
A single title or chapter is played back repeatedly.  
Pressing the REPEAT button cycles the display on  
the screen as follows.  
Press the number buttons to enter the desired chap-  
ter number during playback. The selected chapter  
will be located within the current title and then  
played back.  
Title search starts when any number button is  
pressed during stop mode.  
REPEAT  
[CHAPTER]  
The current chapter is  
played back repeatedly.  
You can also press the SEARCH MODE button, use  
the number or K/L buttons to enter the chapter num-  
ber, and then press the PLAY button.  
REPEAT  
[TITLE]  
The current title is  
played back repeatedly.  
REPEAT  
[OFF]  
No repeat playback.  
For title search, call up the chap-  
ter search screen, press the  
SEARCH MODE button, and  
then operate in the same manner  
as above.  
SEARCH/CHAPTER  
TOTAL CHAPTERS: 027  
CHAPTER  
Start  
[
15 ]  
_
If normal playback is performed after REPEAT  
CHAPTER has been selected without any chapter  
number entered, the first chapter is played back  
repeatedly. If the chapter number is changed using  
the number buttons or the SKIP buttons (H G)  
during playback, the newly selected chapter is  
played back repeatedly.  
Exit  
Pressing the SEARCH MODE but-  
ton during playback causes the cur-  
rent chapter or title number to be  
displayed in square brackets.  
SEARCH/TITLE  
TOTAL TITLES: 07  
TITLE  
[
5 ]  
_
Start  
Exit  
NOTE:  
Playback from a desired title or chapter is not avail-  
able with some DVDs.  
For audio CDs  
The whole disc or a single track is played back  
repeatedly.  
RANDOM (Audio CD)  
Pressing the REPEAT button cycles the display on  
the screen through REPEAT TRACK, REPEAT  
ALL and REPEAT OFF.  
CD  
REPEAT  
[TRACK]  
The current track is  
played back repeatedly.  
1 Press the MODE button in stop mode.  
The program setting menu screen will appear.  
REPEAT  
[ALL]  
The whole disc is  
played back repeatedly.  
2 Press the MODE button again.  
REPEAT  
[OFF]  
No repeat playback.  
RANDOM  
If normal playback is performed after REPEAT  
Start  
Exit  
TRACK has been selected without any track num-  
ber entered, the first track will be played back  
repeatedly. If the track number is changed using  
the number buttons or the SKIP buttons (H G)  
during playback, the newly selected track is played  
back repeatedly.  
3 Press the PLAY button. Random playback will  
then start.  
NOTE:  
If the REPEAT button is pressed during program  
playback, that program is played back repeatedly.  
Program playback is not available during random  
playback.  
NOTE:  
Repeat playback is not available with some discs  
- 24 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-B REPEAT  
PROGRAM (Audio CD)  
DVD  
CD  
CD  
You can define a section to be played back repeatedly.  
1 Press the MODE button in stop mode.  
The program screen will appear.  
PROGRAM  
T
[
] / 18 TOTAL 0h 00m 00s  
__  
1 Press the A-B REPEAT button during play-  
back.  
REPEAT  
[ A -  
]
The starting point (A) will then  
be selected.  
Start,  
Delete  
Exit  
2 Press the number or K/L buttons to enter the  
desired track numbers, and then press the  
ENTER button to select the settings.  
2 Press the A-B REPEAT button again at the  
PROGRAM  
[1_2 ] / 14 TOTAL 0h 27m 46s  
The total playback time for the  
selected tracks will appear on the  
TOTAL line.  
T
end point (B) of the desired section.  
01: 02  
02: 04  
03: 06  
04: 09  
05: 01  
06: 03  
07: 05  
08: 07  
09: 13  
10: 08  
11: 12  
12: 14  
13: 10  
14: 11  
The selected section will be  
played back repeatedly.  
REPEAT  
[ A - B ]  
Start,  
Delete  
Exit  
3 Press the PLAY button.  
Playback will start in the programmed order.  
The contents of the program are retained after the  
program playback ends.  
3 To exit A-B repeat playback, press the A-B  
REPEAT button and set it to OFF.  
REPEAT  
[ OFF ]  
NOTES:  
Addition or confirmation of programs is not possi-  
ble during program playback. You must stop the  
current playback before such operations can be car-  
ried out.  
NOTES:  
If B is selected at a point which is earlier than  
point A, the previous setting of A is canceled and  
the point selected as B will become the setting for  
A.  
With DVDs, the A-B repeat section can be set only  
within the current title.  
With audio CDs, the A-B repeat section can be set  
across different tracks.  
Press the CLEAR button to cancel a program. The  
most recently entered program will then be deleted.  
Up to 20 programs can be stored at any time.  
PROGRAM  
T
[__] / 14 TOTAL 0h 27m 46s  
01: 09  
02: 03  
03: 04  
04: 07  
05: 01  
06: 02  
07: 12  
08: 10  
09: 13  
10: 08  
11: 01  
12: 14  
13: 10  
14: 11  
Start,  
Delete  
Exit  
A-B repeat is not available with some scenes in  
DVD.  
Numbers which exceed the number of tracks on the  
disc in the tray are not accepted.  
Playback from a desired track and random play-  
back are not available during program playback.  
Program settings are cleared when the power is  
turned off or the disc loading tray is opened.  
- 25 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTINGS  
NOTES:  
CHANGING THE AUDIO  
LANGUAGE OR SOUND MODE  
Pressing the K/L buttons may not work on some  
DVDs with multiple audio languages (e.g. DVDs  
which allow audio language setting on the disc  
menu). Operation varies between discs, so refer to  
the manual accompanying the disc.  
DVD  
CD  
The TV/DVD has a function which allows you to  
select the desired audio language and sound mode.  
If a desired language is not shown after pressing  
the K/L buttons several times, the disc does not  
have an audio source in that language.  
The audio language resets to the one which has  
been selected in the setup mode, every time the  
power is turned on or discs are replaced. If that lan-  
guage is not available on a disc, a language defined  
by the disc is selected.  
For DVDs  
Press the AUDIO button during playback, and then  
press the K/L buttons to select the desired audio  
language.  
The audio language can be changed if multiple lan-  
guages are recorded on the DVD being played.  
The screen display will disappear after about 15  
seconds.  
If you use DIGITAL AUDIO OUT jack, the sound  
mode of audio CDs can not be changed.  
AUDIO  
AUDIO  
1
2
:
:
E N G /8  
F
R E /8  
AUDIO  
8
:
J P N /8  
Bon jour  
HELLO  
For audio CDs  
Press the AUDIO button during playback.  
Pressing the K/L buttons cycles the sound mode  
through STEREO, L-CH and R-CH.  
Both right and left channels  
are active (stereo).  
AUDIO  
AUDIO  
S
T E R E O  
Only the right channel is active.  
R
L
-
-
C H  
C H  
Only the left channel is active.  
AUDIO  
- 26 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SUBTITLE  
LANGUAGE  
CHANGING THE CAMERA  
ANGLE (Multi-Angle Pictures)  
DVD  
DVD  
The TV/DVD has a function which allows you to  
select the desired language for subtitles.  
The TV/DVD has a function which allows you to  
select the desired camera angle.  
Press the SUBTITLE button during playback, and  
then press the K/L buttons to select the desired  
subtitle language.  
1 Press the ANGLE button during playback.  
If the disc contains sequences recorded from differ-  
ent camera angles, the angle icon (  
) will appear  
The subtitle language can be changed if the subti-  
tles are recorded in multiple languages on the DVD  
being played.  
at the bottom-right of the screen. You can change  
the camera angle when the icon appears on the  
screen.  
The camera angle cannot be changed if the disc  
does not contain sequences recorded from different  
camera angles.  
The subtitle language cannot be changed if the sub-  
titles are recorded in a single language on the DVD  
being played.  
SUBTITLE  
SUBTITLE  
1
:
E N G /8  
Subtitle 1  
Subtitle 2  
2 Press the K/L buttons while the angle num-  
ber is shown on the screen.  
2
:
F R E /8  
ANGLE [ 1 ]/8  
Angle 1 (default)  
SUBTITLE  
0
:
O F F /8  
ANGLE [ 2 ]/8  
Angle 2  
No subtitles  
Angle 8  
ANGLE [ 8 ]/8  
Bon jour  
HELLO  
NOTE:  
The screen display will disappear after about 15  
seconds.  
Pressing the K/L buttons cycles the subtitle lan-  
guage from SUBTITLE 1, SUBTITLE 2 and all  
the languages recorded through to OFF.  
NOTES:  
Some discs allow subtitle language setting on the  
disc menu. (Operation varies between discs, so  
refer to the manual accompanying the disc.)  
If the desired language is not shown after pressing  
the K/L buttons several times, the disc does not  
have subtitles in that language.  
The subtitle language resets to the one which has  
been selected in the setup mode, every time the  
power is turned on or discs are replaced. If that  
language is not available on a disc, a language  
defined by the disc is selected.  
It may take time to display the subtitles in the  
selected language.  
The screen display will disappear after about 15  
seconds.  
- 27 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE ON-SCREEN  
DISPLAY  
DVD  
CD  
You can check the information about the disc by  
pressing the DISPLAY button on the remote control.  
For DVDs  
Press the DISPLAY button.  
Pressing the DISPLAY button cycles the display on  
the screen.  
Current title number / total number of titles.  
TITLE  
TIME  
REMAIN  
:
01/04  
0h10m25s  
0h05m25s  
Elapsed time of the current title.  
Remaining time of the current title.  
Current chapter number / total number of chapters  
in the current title.  
CHAPTER  
TIME  
REMAIN  
:
001/010  
0h02m25s  
0h01m31s  
Elapsed time of the current chapter.  
Remaining time of the current chapter.  
Current language for the sound.  
Current audio format.  
AUDIO  
:
1.ENGLISH  
DOLBY DIGITAL  
6CH  
Current language for the subtitles.  
Selected angle / total number of angles.  
VIRTUAL 3D setting(ON/OFF).  
SUBTITLE  
ANGLE  
VIRTUAL 3D  
:
:
2.FRENCH  
8/8  
No display  
NOTE:  
DOLBY DIGITAL 5.1 Channel is displayed as  
"DOLBY DIGITAL 6CH".  
For audio CDs  
Press the DISPLAY button.  
Pressing the DISPLAY button toggles the display  
on the screen.  
Current track number / total track number.  
TRACK  
TIME  
REMAIN  
:
01/04  
0h05m25s  
0h01m31s  
Elapsed time of the current track.  
Remaining time of the current track.  
Current play mode.  
PROGRAM  
No display  
- 28 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHANGING THE SETUP ITEMS  
DVD  
LANGUAGE SETTINGS  
4 Press the K/L or number buttons to select a  
desired item, and then press the ENTER but-  
ton.  
1 Press the SETUP button.  
The setup screen appears.  
SETUP  
If OTHER is selected on the AUDIO, SUBTITLE  
or DISC MENU setting screen, the COUNTRY  
CODE setting screen will appear. Press the number  
buttons to enter the desired language (country)  
code while referring to the list on page 33, and then  
1. LANGUAGE  
2. VIDEO  
3. AUDIO  
4. LOCK  
5. OTHERS  
Enter  
/
Exit  
press the ENTER button.  
SETUP/LANGUAGE  
COUNTRY CODE  
2 Press the K/L or number buttons to select  
[ _ _ _ _ ]  
LANGUAGE, and then press the ENTER but-  
ton.  
SETUP/LANGUAGE  
Enter,  
Back  
Exit  
1. AUDIO  
2. SUBTITLE  
3. DISC MENU  
[ENG]  
[AUTO]  
[ENG]  
4. PLAYER MENU [ENG]  
5 Press the SETUP button.  
Enter,  
Back  
Exit  
The setup mode will be canceled and the ordinary  
screen will appear.  
3 Press the K/L or number buttons to select an  
item, and then press the ENTER button.  
NOTES:  
If the automatically selected language in "AUTO"  
for subtitle is same as the selected language for  
"AUDIO", the subtitle will not be shown.  
If the number buttons are used in steps 2 to 4, the  
settings are immediately selected. (You do not need  
to press the ENTER button.)  
SETUP/LANGUAGE  
AUDIO  
The original language of each disc will be selected.  
Voice is played back in English.  
Voice is played back in Spanish.  
Voice is played back in French.  
1. ORIGINAL  
2. ENGLISH  
3. SPANISH  
4. FRENCH  
5. OTHER  
You can select other languages for audio playback.  
Enter,  
Back  
Exit  
SETUP/LANGUAGE  
SUBTITLE  
Language Setting for AUDIO and SUBTITLE is  
Subtitles are shown in the automatically selected  
language  
1. AUTO  
.
not available with some discs. Then use the  
AUDIO and SUBTITLE button. Details are on  
pages 26 and 27.  
An on-screen display language must be selected  
each for the TV mode and DVD mode.  
2. ENGLISH  
3. SPANISH  
4. FRENCH  
5. OTHER  
Subtitles are shown in English.  
Subtitles are shown in Spanish.  
Subtitles are shown in French.  
Enter,  
Back  
Exit  
Exit  
Exit  
You can select other languages for subtitles.  
SETUP/LANGUAGE  
DISC MENU  
The disc menu is shown in the automatically  
selected language.  
The disc menu appears in English.  
The disc menu appears in Spanish.  
The disc menu appears in French.  
1. AUTO  
2. ENGLISH  
3. SPANISH  
4. FRENCH  
5. OTHER  
Enter,  
Back  
You can select other languages for the disc menu.  
SETUP/LANGUAGE  
PLAYER MENU  
1. ENGLISH  
2. SPANISH  
3. FRENCH  
The on-screen display appears in English.  
The on-screen display appears in Spanish.  
The on-screen display appears in French.  
Enter,  
Back  
- 29 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO SETTINGS  
AUDIO SETTINGS  
1 Press the SETUP button.  
The setup screen will appear.  
1 Press the SETUP button.  
The setup screen will appear.  
SETUP  
1. LANGUAGE  
2. VIDEO  
3. AUDIO  
4. LOCK  
5. OTHERS  
SETUP  
1. LANGUAGE  
2. VIDEO  
3. AUDIO  
4. LOCK  
5. OTHERS  
Enter  
/
Exit  
Enter  
/
Exit  
2 Press the K/L or number buttons to select  
2 Press the K/L or number buttons to select  
AUDIO, and then press the  
SETUP/AUDIO  
VIDEO, and then press the ENTER button.  
ENTER button.  
1. DIGITAL OUT  
2. VIRTUAL 3D  
[OFF]  
SETUP/VIDEO  
1. TV MODE  
2. STILL MODE  
[4:3LB]  
[AUTO]  
Enter,  
Back  
Exit  
Enter,  
Back  
Exit  
3 Press the K/L or number buttons to select an  
item, and then press the ENTER button.  
3 Press the K/L or number buttons to select an  
SETUP/AUDIO  
DIGITAL OUT  
Sets the sample rate for playing a disc recorded  
with high sound quality.  
When a Dolby Digital decoder is connected.  
When a DTS decoder is connected.  
item, and then press the ENTER button.  
1. PCM  
2. DOLBY DIGITAL [OFF]  
3. DTS [OFF]  
[48kHz]  
SETUP/VIDEO  
TV MODE  
Full-height pictures are shown with one or both  
sides trimmed.  
Wide screen (full-width) pictures are shown  
with black bars at top and bottom.  
1. 4:3 PAN&SCAN  
2. 4:3 LETTER BOX  
3. 16:9 WIDE  
Enter,  
Back  
Exit  
If a wide screen TV is connected.  
SETUP/AUDIO  
VIRTUAL 3D  
Enter,  
Back  
Exit  
1. OFF  
2. ON  
To activate the 3D effect.  
SETUP/VIDEO  
STILL MODE  
1. AUTO  
2. FIELD  
AUTO is normally selected.  
Enter,  
Back  
Exit  
If pictures are blurred in auto mode.  
For showing motionless pictures at high  
resolution in still mode.  
3. FRAME  
Enter,  
Back  
Exit  
4 Press the K/L or number buttons to select the  
desired item, and then press the ENTER but-  
ton.  
4 Press the K/L or number buttons to select the  
desired item, and then press the ENTER but-  
ton.  
If PCM, DOLBY DIGITAL or DTS is selected on  
the DIGITAL OUT setting screen, press the K/L or  
number buttons again to select a further item, and  
then press the ENTER button.  
5 Press the SETUP button.  
The setup mode will be canceled and the ordinary  
screen will appear.  
Audio signals are converted to 48 kHz/16 bit  
signals for digital output when playing a DVD  
recorded with high sound quality (48 kHz/  
20 bit/24 bit, 96 kHz).  
SETUP/AUDIO  
PCM  
1. 48kHz  
2. 96kHz  
Sound is reproduced at the high quality of  
96 kHz when playing a DVD recorded with high  
NOTE:  
If the number buttons are used in steps 2 to 4, the  
settings are immediately selected. (You do not need  
to press the ENTER button.)  
Enter,  
Back  
Exit  
sound quality (48 kHz/20 bit/24 bit, 96 kHz).  
For 48 kHz discs or when 4:3 LETTER BOX  
is selected in TV MODE, sound is reproduced  
at 48 kHz  
.
SETUP/AUDIO  
DOLBY DIGITAL  
1. OFF  
2. ON  
When a Dolby Digital decoder built-in amplifier  
is used.  
Enter,  
Back  
Exit  
SETUP/AUDIO  
DTS  
1. OFF  
2. ON  
When a DTS decoder built-in amplifier is used.  
Enter,  
Back  
Exit  
- 30 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARENTAL LOCK  
5 Press the SETUP button.  
The setup mode will be canceled and the ordinary  
screen will appear.  
1 Press the SETUP button.  
The setup screen will appear.  
SETUP  
1. LANGUAGE  
2. VIDEO  
3. AUDIO  
4. LOCK  
5. OTHERS  
NOTE:  
If the number buttons are used in steps 2 to 4, the  
settings are immediately selected. (You do not need  
to press the ENTER button.)  
Enter  
/
Exit  
2 Press the K/L or number buttons to select  
LOCK, and then press the ENTER button.  
SETUP/LOCK  
PASSWORD  
[ _ _ _ _ ]  
This unit employs TruSurround system  
of SRS Labs, Inc. as the  
1. LEVEL  
2. CHANGE PASSWORD  
[LEVEL8]  
To set the control level to 1 to 8 or none.  
To cancel the current password and set a  
new one on the same screen.  
VIRTUAL 3D technology.  
Enter,  
Back  
TruSurround and the  
symbol are trademarks of  
SRS Labs, Inc. in the United States and selected  
foreign countries.  
TruSurround technology is incorporated under license  
from SRS Labs, Inc.  
3 Press the number buttons to enter the 4-digit  
password, and then press the ENTER button.  
When doing this for the first time, enter any 4 dig-  
its. That number will be used as the password from  
the second time onward.  
SETUP/LOCK  
PASSWORD  
[
]
____  
By entering the password, you  
can then change the control level  
and password settings.  
1. LEVEL  
2. CHANGE PASSWORD  
[LEVEL8]  
Enter,  
Back  
4 Press the K/L or number buttons to select an  
item, and then press the ENTER button.  
When LEVEL is selected  
Press the K/L buttons to select an item from  
LEVEL 1 to LEVEL 8 or NONE, and then press  
the ENTER button.  
SETUP/LOCK  
PARENTAL LOCK  
NONE  
LEVEL 8 [PLAY ALL]  
LEVEL 7 [NC-17]  
LEVEL 6 [R]  
LEVEL 5  
LEVEL 4 [PG-13]  
LEVEL 3 [PG]  
LEVEL 2  
LEVEL 1 [G]  
Enter  
When CHANGE PASSWORD is selected  
The password entry screen will be displayed and  
the password which has already been set will be  
cleared. The four digits entered in step 3 will then  
be set as the new password.  
5
The setup screen will appear.  
- 31 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROL LEVELS  
OTHER SETTINGS  
Level 8  
DVD software of any grade (adult/general/chil-  
dren) can be played back.  
1 Press the SETUP button.  
The setup screen will appear.  
SETUP  
1. LANGUAGE  
2. VIDEO  
3. AUDIO  
Level 7 to 2  
4. LOCK  
5. OTHERS  
Only DVD software intended for general use and  
children can be played back.  
Enter  
/
Exit  
Level 1  
Only DVD software intended for children can be  
played back, with those intended for adult and gen-  
eral use prohibited.  
2 Press the K/L or number buttons to select  
OTHERS, and then press the  
SETUP/OTHERS  
ENTER button.  
1. OSD MESSAGE [ON]  
2. ANGLE ICON  
3. BACKGROUND [BLUE]  
[ON]  
None  
Parental lock is canceled.  
Enter,  
Back  
Exit  
NOTES:  
With some DVDs, it may be difficult to find if they  
3 Press the K/L or number buttons to select an  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way  
that you have set.  
If the number buttons are used in steps 2 to 4, the  
settings are immediately selected. (You do not need  
to press the ENTER button.)  
item, and then press the ENTER button.  
SETUP/OTHERS  
OSD MESSAGE  
1. ON  
2. OFF  
Selects whether to display messages on the  
screen.  
Enter,  
Back  
Exit  
Record the password in case you forget it.  
SETUP/OTHERS  
ANGLE ICON  
1. ON  
2. OFF  
Selects whether to display the angle icon.  
[Cannot remember your password?]  
Reset the setup items and enter the new password  
by the following step:  
Enter,  
Back  
Exit  
SETUP/OTHERS  
BACKGROUND  
1. BLUE  
2. GRAY  
Turns the background to blue.  
Turns the background to gray.  
When the TV/DVD do not run in the DVD mode,  
and while pressing and holding the STOP button  
on the TV/DVD, first press the TV button on the  
remote control, and then press the SLEEP button  
on the remote control and press the 1 button.  
Enter,  
Back  
Exit  
4 Press the K/L or number buttons to select a  
desired item, and then press the ENTER but-  
ton.  
5 Press the SETUP button.  
The setup mode will be canceled and the ordinary  
screen will appear.  
NOTE:  
If the number buttons are used in steps 2 to 4, the  
settings are immediately selected. (You do not need  
to press the ENTER button.)  
- 32 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LANGUAGE CODE LIST  
DVD  
No.  
Language  
Country code  
No.  
Language  
Country code  
1
Afar  
4747  
4748  
4752  
4759  
4764  
4765  
4771  
4772  
4847  
4851  
4853  
4854  
4855  
4860  
4861  
4864  
4947  
4961  
4965  
4971  
5047  
5051  
5072  
5158  
5160  
5161  
5165  
5166  
5167  
5247  
5255  
5256  
5261  
5264  
5271  
5347  
5350  
5358  
5360  
5367  
5447  
5455  
5464  
5467  
5471  
5547  
5551  
5557  
5560  
5565  
5566  
5569  
5647  
5655  
5669  
5747  
5757  
5758  
5759  
5760  
5761  
5765  
5767  
5771  
5847  
5860  
5861  
5866  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
Latvian;Lettish  
Malagasy  
Maori  
5868  
5953  
5955  
5957  
5958  
5960  
5961  
5964  
5965  
5966  
5971  
6047  
6051  
6058  
6061  
6149  
6159  
6164  
6247  
6258  
6265  
6266  
6367  
6459  
6460  
6461  
6467  
6469  
6547  
6550  
6553  
6554  
6555  
6557  
6558  
6559  
6560  
6561  
6563  
6564  
6565  
6566  
6567  
6568  
6569  
6647  
6652  
6653  
6654  
6655  
6657  
6658  
6660  
6661  
6664  
6665  
6666  
6669  
6757  
6764  
6772  
6855  
6861  
6961  
7054  
7161  
7254  
7267  
2
Abkhazian  
Afrikaans  
Amharic  
Arabic  
3
4
Macedonian  
Malayalam  
Mongolian  
Moldavian  
Marathi  
5
6
Assamese  
Aymara  
Azerbaijani  
Bashkir  
7
8
9
Malay  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
Byelorussian  
Bulgarian  
Bihari  
Maltese  
Burmese  
Nauru  
Bislama  
Nepali  
Bengali;Bangla  
Tibetan  
Breton  
Dutch (DUT)  
Norwegian  
Occitan  
Catalan  
(Afan)Oromo  
Oriya  
Panjabi  
Corsican  
Czech  
Welsh  
Polish  
Danish  
Pashto;Pushto  
Portuguese  
Quechua  
Rhaeto-Romance  
Kirundi  
German (GER)  
Bhutani  
Greek  
English (ENG)  
Esperanto  
Spanish (SPA)  
Estonian  
Basque  
Romanian  
Russian  
Kinyarwanda  
Sanskrit  
Sindhi  
Persian  
Finnish  
Fiji  
Sangho  
100 Serbo-Croatian  
101 Singhalese  
102 Slovak  
103 Slovenian  
104 Samoan  
105 Shona  
106 Somali  
107 Albanian  
108 Serbian  
109 Siswat  
110 Sesotho  
111 Sundanese  
112 Swedish  
113 Swahili  
114 Tamil  
115 Telugu  
116 Tajik  
117 Thai  
118 Tigrinya  
119 Turkmen  
120 Tagalog  
121 Setswana  
122 Tonga  
Faroese  
French (FRE)  
Frisian  
Irish  
Scots Gaelic  
Galician  
Guarani  
Gujarati  
Hausa  
Hindi  
Croatian  
Hungarian  
Armenian  
Interlingua  
Interlingue  
Inupiak  
Indonesian  
Icelandic  
Italian (ITA)  
Hebrew  
Japanese (JPN)  
Yiddish  
Javanese  
Georgian  
Kazakh  
Greenlandic  
Cambodian  
Kannada  
Korean (KOR)  
Kashmiri  
Kurdish  
123 Turkish  
124 Tsonga  
125 Tatar  
126 Twi  
127 Ukrainian  
128 Urdu  
129 Uzbek  
130 Vietnamese  
131 Volapuk  
132 Wolof  
Kirghiz  
Latin  
Lingala  
Laothian  
Lithuanian  
133 Xhosa  
134 Yoruba  
135 Chinese (CHI)  
136 Zulu  
- 33 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
TV  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
Problem  
Corrective Action  
Remote Control Doesnt Work  
Is TV/DVD plugged in?  
Power at outlet?  
Check batteries in Remote Control.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Bars On Screen  
Picture Distorted or Blurred  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust COLOR control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Adjust CONTRAST & BRIGHT control.  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Picture OK, Sound Poor  
No Picture or Sound  
Try a new channel, if OK, then possible station trouble.  
Is TV/DVD plugged in?  
Power at outlet?  
Is TV/DVDS POWER button on?  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Turn off with POWER button and then turn it on after about a minute.  
- 34 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Closed Caption Problem  
My TV is showing captions  
that are misspelled.  
Possible Remedy  
You are watching a live broadcast and spelling errors made by the  
closed captioning production company may pass through uncorrected.  
A prerecorded program will not show any misspelled words because  
of the normal time available for editing the captions.  
My TV will not show the text  
Captions that are delayed a few seconds behind the actual dialogue  
in its entirety or there is a delay of are common for live broadcast. Most captioning production companies  
what is being said.  
can display a dialogue to a maximum of 220 words per minute. If a  
dialogue exceeds that rate, selective editing is used to insure that the  
captions remain up-to-date with the current TV screen dialogue.  
Interference caused by building, power lines, thunderstorms, etc.  
may cause scrambled or incomplete captions to appear.  
My captions are scrambled with  
white boxes on the TV screen.  
My program guide listed a TV show Broadcasters may at times use a time compression process to the  
as being closed captioned but none actual program so that additional advertising time can be given.  
of the captions were displayed.  
Since the decoder cannot read the compressed information,  
captions will be lost.  
My TV screen shows a black box  
on certain channels.  
You are in the TEXT mode. Select CAPTION mode or CAPTION  
[OFF].  
- 35 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
If the TV/DVD does not perform properly when operated as instructed in this Owners Manual, check the  
player, consulting the following checklist.  
Symptom  
No power.  
let.  
Cause  
Loose power plug.  
Remedy  
Insert the power plug firmly into the wall out-  
The player does not  
respond to the  
The remote control is not aimed Aim the remote control directly at the sensor  
at the sensor on the TV/DVD.  
Obstacles present between the  
remote control and the sensor.  
The remote control is too far  
away from the TV/DVD.  
Dead batteries.  
on the TV/DVD.  
Remove the obstacles from the signal path.  
remote control.  
Use the remote control within 7m of  
the TV/DVD.  
Replace the batteries.  
Connect the video cables firmly.  
Insert a correct video disc that plays on this  
TV/DVD.  
Insert a disc.  
Clean the disc.  
Place the disc correctly, with the label side up.  
Cancel the parental lock or change the control  
level.  
No picture  
Loose video connection.  
Wrong disc.  
Disc cannot be  
played  
No disc.  
Dirty disc.  
Disc is placed upside down.  
Parental lock is active.  
No sound  
Loose audio connection.  
The power of the connected  
audio component is off.  
Connect the audio cables firmly.  
Turn the power of the audio component on.  
Wrong audio output settings.  
Wrong input settings on the  
connected audio component.  
Immediately after playing,  
press fast forward or in reverse.  
Correct the audio output settings.  
Correct the input settings on the audio  
component.  
There are some cases where pictures may be  
slightly distorted, which are not a sign of a  
malfunction.  
No malfunction.  
No malfunction.  
No malfunction.  
No malfunction.  
Distorted picture  
Audio or subtitle  
language does not  
match the setup.  
The camera angle  
cannot be changed.  
The selected language is not  
available for audio or subtitles  
on the DVD.  
The DVD does not contain  
sequences recorded from  
different camera angles.  
The DVD does not contain  
audio source or subtitles in the  
selected language.  
That operation is prohibited by  
the TV/DVD or disc.  
Audio or subtitle  
language cannot be  
changed.  
"Prohibited icon"  
appears on the  
screen, prohibiting  
an operation.  
CD sound dropout  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
Scratched disc  
Replace the disc with unscratched one.  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owners Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
- 36 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CABINET CLEANING  
SERVICING  
Wipe the front panel and other exterior surfaces of  
the TV/DVD with a soft cloth immersed in luke-  
warm water and wrung dry.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV/DVD. Such chemicals  
may cause damage and discoloration to the  
exposed surfaces.  
Should your TV/DVD become inoperative, do not  
try to correct the problem by yourself. There are no  
user-serviceable parts inside. Turn off, unplug the  
power cord, and please call our help line at 1-800-  
968-3429, to locate an Authorized Service Center.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the player still does not perform properly when it is operated while referring to the relevant sections and to  
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult  
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.  
DISC HANDLING  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
Use discs which have the following logos on them.  
(Optical audio digital discs.)  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
Do not use detergent or abrasive cleaning agents.  
Always store the disc in its protective case when it  
is not used.  
- 37 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
Television system:  
NTSC-M  
TV Standard  
OTHER SPECIFICATIONS  
Terminals  
Closed caption system: §15.119/FCC  
Channel coverage:  
Antenna input:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
VHF:  
UHF:  
CATV:  
2 ~ 13  
14 ~ 69  
Video input:  
Audio L/R input:  
Headphone:  
Coaxial digital  
audio output  
(only DVD):  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channel  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
1/8stereo (3.5 mm)  
Tuning System:  
Channel access:  
One pin jack,  
500m Vpp (75 ohm)  
Analog audio L/R  
output (only DVD): RCA connector [ 2  
Remote control:  
Digital encoded  
infrared light system  
Operating  
temperature:  
DVD  
5ºC to 40ºC  
(41ºF~104ºF)  
Power requirements: AC 120V, 60Hz  
Power consumption  
Product type:  
Discs:  
Output signal format: NTSC color  
Frequency response  
(out put jack)  
DVD (linear sound): 20 Hz to 22 kHz  
(sample rate: 48 kHz)  
DVD Player  
DVD video, Audio CD  
(Maximum):  
Picture tube:  
Dimensions:  
95W  
19"  
H:19-21/32(499.5mm)  
W:19-7/16(494mm)  
D:20-5/16(465mm)  
44.1 lbs (20kg)  
Remote Control Unit with  
2"AA"batteries  
Owners Manual  
20 Hz to 44 kHz  
(sample rate: 96 kHz)  
20 Hz to 20 kHz  
Weight:  
Accessories:  
CD:  
Signal-to-noise ratio  
(S/N ratio)(out put jack)  
CD:  
100 dB (EIAJ)  
Dynamic range  
(out put jack)  
DVD (linear sound): 85 dB  
CD:  
84 dB (EIAJ)  
Total distortion factor  
CD:  
Wow and flutter:  
0.07% (EIAJ)  
Below the measurement  
limitation (+/-0.001%  
W PEAK) (EIAJ)  
Designs and specifications are subject to change without notice and without our legal obligation.  
If there is a discrepancy between languages, the default language will be English.  
- 38 -  
EN  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Modo del reproductor DVD:  
CONTROLES DE OPERACIÓN Y  
SUS FUNCIONES  
Visualiza el estado actual en la pantalla del televisor con fines  
de comprobación.  
24. Botón de modo búsqueda (SEARCH MODE)– Púlselo para  
Consulte las figuras 1-3 de las páginas 8 y 9.  
localizar el punto deseado.  
25. Botón de audio (AUDIO)– Púlselo para seleccionar el modo de  
sonido o idioma de audio deseado.  
26. Botón de subtítulo (SUBTITLE)– Púlselo para seleccionar un  
idioma de subtítulos deseado.  
27. Botón de repetición (REPEAT)– Repita la reproducción del  
Para utilizarlo como mando a distancia del televisor, pulse el  
botón TV del mando a distancia después de seleccionar el  
modo del televisor. Los botones de control del televisor se  
indican en color azul o blanco.  
Para utilizarlo como mando a distancia del reproductor DVD,  
pulse el botón DVD del mando a distancia después de selec-  
cionar el modo del reproductor DVD. Los botones de control  
del reproductor DVD se indican en color amarillo o blanco.  
disco, título, capítulo o pista actual.  
28. Botón de ángulo (ANGLE)– Púlselo para cambiar el ángulo de  
la cámara y ver la escena reproduciéndose desde un ángulo  
diferente.  
1. Bandeja de carga del disco  
29. Botón de repetición A-B (A-B REPEAT)– Repite la reproduc-  
ción de una sección seleccionada.  
2. Toma de entrada de vídeo (VIDEO)– Se conecta a la toma de  
salida de vídeo de una videocámara o videograbadora.  
30. Botón de retorno (RETURN)– Se utiliza para volver a la  
operación anterior.  
31. Botón de aceptación (ENTER)– Púlselo para aceptar un ajuste.  
32. Botones de flechas–  
3. Tomas de entrada de audio izquierda/derecha (AUDIO L/R)–  
Se conectan a las tomas de salida de audio de una videocámara  
o videograbadora.  
4. Botón de alimentación (POWER)– Púlselo para conectar y  
Modo del televisor:  
desconectar la alimentación.  
5. Botones de volumen (VOLUME /L)– Púlselos para controlar  
Púlselo para seleccionar un modo de ajuste en los menús que  
aparecen en la pantalla del televisor.  
Púlselo para seleccionar o ajustar desde un menú particular.  
K
el nivel del sonido del reproductor DVD y del televisor.  
K
6. Botones de canales (CHANNEL /L)– Púlselos para selec-  
Modo del reproductor DVD:  
cionar los canales memorizados.  
7. Ventanilla receptora de señales del mando a distancia  
8. Botón de parada (STOP)– Detiene el disco.  
9. Botón de rebobinado (REV)– Activa la reproducción en retro-  
ceso rápido hasta un punto deseado.  
10. Botón de reproducción (PLAY)– Inicia la reproducción del  
Se utiliza para hacer ajustes mientras se observa la visual-  
ización en la pantalla del televisor.  
33. Botón de menú (MENU)– Visualiza los menús del reproductor  
DVD y del televisor.  
34. Botón de selección (SELECT)– Púlselo para cambiar al modo  
del televisor, al modo de entrada exterior o al modo del repro-  
ductor DVD.  
contenido del disco.  
11. Botón de avance (FWD)– Activa la reproducción en avance  
rápido hasta un punto deseado.  
12. Botón de pausa (PAUSE)– Hace una pausa en el disco actual.  
13. Botón de abrir/cerrar (OPEN/CLOSE)– Púlselo para introducir  
un disco en la bandeja o para sacarlo de ella.  
14. Toma de auriculares (HEADPHONE)– Para conectar unos  
auriculares (no suministrados) y escuchar en privado.  
15. Botón del televisor (TV)– Púlselo para controlar el televisor.  
16. Botón numerados (NUMBER)–  
35. Botón de silenciamiento (MUTE)– Púlselo para apagar el  
sonido de un programa de televisión. (La visualización del  
nivel del sonido cambia de AZUL CLARO a ROJO CLARO.)  
Pulse de nuevo este botón o pulse el botón VOL K o L para  
reponer el sonido.  
36. Botón DVD– Púlselo para controlar el reproductor DVD.  
37. Cable de alimentación– Conéctelo a una toma de CA estándar  
(120 V/60 Hz).  
NOTA: Retire el cable de alimentación del gancho para impedir  
que se rompa algún hilo conductor antes de conectar el cable a  
una toma de CA.  
Modo del televisor:  
Pulse dos dígitos para acceder directamente al canal deseado.  
No se olvide de pulsar "0" antes de introducir un canal de un  
solo dígito.  
38. Toma de salida de audio digital COAXIAL– Conéctela a otro  
amplificador o descodificador.  
39. Toma de salida de audio izquierda/derecha (AUDIO L/R)–  
Botón +100–  
Conéctela a otro amplificador o descodificador.  
Púlselo para seleccionar canales de televisión por cable con un  
número igual o superior al 100.  
Modo del reproductor DVD:  
40. Toma de entrada de antena (ANT.)– Conéctela a una antena,  
sistema de televisión por cable o sistema de televisión por  
satélite.  
Púlselo para introducir el número deseado.  
Botón +10–  
Púlselo para introducir números iguales o superiores al 10.  
PREPARACIÓN PARA LA UTILIZACIÓN  
17. Botón del temporizador para dormir (SLEEP)– Pulse el botón  
SLEEP para visualizar el temporizador para dormir y activar la  
función. La hora de apagado puede determinarse mediante el  
número de veces que usted pulse el botón (0, 10, 20, 30, ... 90,  
0 minutos).  
CONEXIONES DE ANTENA/TELEVISIÓN  
POR CABLE  
ANTENA COMBINADA DE VHF/UHF  
18. Botones de salto (SKIP)– Para saltar capítulo o pistas hasta un  
La antena de varilla de VHF/UHF (suministrada) puede desmon-  
tarse. Inserte el vástago de la antena en el agujero de la parte supe-  
rior trasera del televisor/reproductor DVD. Conecte la antena de  
varilla de VHF/UHF o la antena combinada de VHF/UHF en el  
terminal ANT. del televisor/reproductor DVD como se muestra en  
el diagrama de abajo. Para obtener la mejor recepción, extienda  
completamente la antena de varilla de VHF/UHF y haga los  
ajustes necesarios. (Evite tocar la sección superior cuando haga el  
ajuste.)  
punto deseado.  
19. Botón de modo (MODE)– Activa el modo de reproducción de  
programas o de reproducción aleatoria.  
20. Botón de preparación (SETUP)– Púlselo para introducir el  
modo de preparación o para cambiar ítems de preparación.  
21. Botón de título (TITLE)– Visualiza el menú de títulos.  
22. Botón de cancelar (CLEAR)– Cancela un ajuste.  
23. Botón del visualizador (DISPLAY)–  
Modo del televisor:  
Púlselo para visualizar el número del canal en la pantalla. Si lo  
presiona de nuevo, el número del canal desaparecerá.  
- 39 -  
ES  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTA: Antes de conectar la antena de varilla en el terminal de  
antena, compruebe que la clavija no esté doblada. Si lo está,  
enderécela como se muestra en la ilustración, y luego conecte la  
clavija en el terminal de la antena.  
Consulte la figura 8 de la página 12.  
CONEXIÓN A UN SISTEMA ESTÉREO  
(Para DVD)  
Clavija doblada  
Consulte la figura 9 de la página 13.  
Cable  
Clavija  
NOTAS:  
Asegúrese de desconectar la alimentación de todos los compo-  
nentes del sistema antes de hacer conexiones a otro compo-  
nente.  
(Clavija derecha)  
(Necesita ser enderezada)  
Consulte la figura 4 de la página 10.  
Consulte también los manuales de instrucciones del sistema  
estéreo y de otros componentes que vayan a ser conectados al  
televisor/reproductor DVD.  
NOTA: La conexión de una antena interior tal vez no ofrezca  
siempre una recepción de televisión aceptable.  
ANTENAS SEPARADAS DE VHF/UHF  
En algunas zonas será necesario utilizar una antena exterior.  
CONEXIÓN A UN AMPLIFICADOR  
EQUIPADO CON TOMAS DE ENTRADA  
DIGITAL, PLATINA MD O PLATINA DAT  
(Para DVD)  
Consulte la figura 5 de la página 10.  
TELEVISIÓN POR CABLE SIN CAJA DE  
CONVERSIÓN/DESCODIFICADOR  
Utilice esta conexión si su sistema de televisión por cable se  
conecta directamente a su televisor/reproductor DVD sin caja de  
conversión.  
Utilice cables de audio digital coaxial (de venta en el comercio)  
para hacer las conexiones de audio.  
Consulte la figura 10 de la página 13.  
Consulte la figura 6 de la página 11.  
NOTAS:  
La fuente de audio de un disco del formato de sonido ambiental  
Dolby Digital de 5,1 canales no puede grabarse como sonido  
digital por una platina MD o DAT.  
Asegúrese de desconectar la alimentación de todos los compo-  
nentes del sistema antes de hacer conexiones a otro compo-  
nente.  
Consulte también los manuales de los componentes que vayan a  
ser conectados al televisor/reproductor DVD.  
En el modo de preparación, ponga DOLBY DIGITAL y DTS en  
TELEVISIÓN POR CABLE CON CAJA DE  
CONVERSIÓN/DESCODIFICADOR O CAJA DE TELE-  
VISIÓN POR SATÉLITE  
Si sus servicio de televisión por cable le suministra una caja de  
conversión, o si usted utiliza un sistema de televisión por satélite,  
usted podrá utilizar la conexión básica mostrada aquí.  
Consulte la figura 7 de la página 11.  
APDO. para la salida de audio. Hacer la reproducción en un  
televisor/reproductor DVD utilizando ajustes incorrectos puede  
generar ruidos, y también puede estropear los altavoces.  
Aviso a los instaladores de sistemas CATV:  
Este aviso se incluye para que los instaladores de sistemas  
CATV tenga en cuenta el Artículo 820-40 del NEC, que pro-  
porciona consejos para hacer una conexión apropiada a tierra y,  
en particular, especifica que el cable de tierra deberá conectarse  
a un sistema de puesta a tierra del edificio tan cerca del punto  
de entrada del cable como sea posible.  
Cuando ponga DOLBY DIGITAL en APDO. y 3D VIRTUAL  
en ENC. para la salida de audio en el modo de preparación y  
seleccione la fuente de audio en un formato de sonido ambiental  
Dolby Digital de 5,1 canales, el audio se silenciará.  
CONEXIÓN A UN DESCODIFICADOR  
DOLBY DIGITAL O A UN DESCODIFI-  
CADOR DTS (Para DVD)  
Si utiliza este televisor/reproductor DVD para reproducir en el for-  
mato de sonido ambiental Dolby Digital de 5,1 canales o en el for-  
mato de sonido ambiental DTS, el televisor/reproductor DVD dará  
salida al flujo de datos Dolby Digital o DTS desde su toma de sali-  
da de audio digital COAXIAL. Conectando el reproductor a un  
descodificador Dolby Digital o DTS, usted podrá disfrutar de un  
ambiente más convincente y real, con un sonido ambiental potente  
y de alta calidad de tipo profesional como el que puede oírse en  
los cines.  
INSTALACIÓN DE LAS PILAS  
1) Abra la cubierta del compartimiento de las pilas presionando la  
cubierta del mando a distancia en el sentido de la flecha.  
2) Inserte 2 pilas "AA" en el compartimiento de las pilas, en el  
sentido indicado por las  
marcas de polaridad (+/-).  
3) Vuelva a poner la cubierta.  
CONEXIÓN A TOMAS DE ENTRADA  
EXTERIOR  
Cuando vea un programa grabado en otra fuente (videograbadora o  
videocámara), utilice las tomas de entrada de audio/vídeo de la  
parte delantera del televisor/reproductor DVD.  
Utilice los cables digitales coaxiales de audio (de venta en el com-  
ercio) para hacer las conexiones de audio.  
Consulte la figura 11 de la página 14.  
Conecte las tomas de salida de audio/vídeo de otra fuente a las  
tomas AUDIO L/R y VIDEO de este televisor/reproductor DVD.  
Y luego pulse el botón SELECT hasta que aparezca "AUX" en la  
pantalla.  
NOTAS:  
Asegúrese de desconectar la alimentación de todos los compo-  
nentes del sistema antes de hacer conexiones a otro compo-  
nente.  
NOTA:  
Consulte también los manuales de los componentes que vayan a  
ser conectados al televisor/reproductor DVD.  
Si hace la conexión a un descodificador Dolby Digital, en el  
modo de preparación, ponga DOLBY DIGITAL en ENC. para  
la salida de audio.  
Cuando conecte una videograbadora mono (otra fuente) a este  
televisor/reproductor DVD, conecte la toma de salida de audio  
de la videograbadora mono (otra fuente) a la toma AUDIO L de  
este televisor/reproductor DVD. El audio saldrá por los canales  
L y R de la misma forma.  
Si hace la conexión a un descodificador DTS, en el modo de  
- 40 -  
ES  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
preparación, ponga DTS en ENC. para la salida de audio.  
[FUNCIÓN DE AGREGAR/BORRAR]  
A menos que haga la conexión a un descodificador Dolby  
Digital o a un descodificador DTS, en el modo de preparación,  
ponga DOLBY DIGITAL y DTS en APDO. para la salida de  
audio. Hacer la reproducción en un televisor/reproductor DVD  
utilizando ajustes incorrectos puede generar ruidos, y también  
puede estropear los altavoces.  
Cuando ponga DOLBY DIGITAL en APDO. y 3D VIRTUAL  
en ENC. para la salida de audio en el modo de preparación y  
seleccione la fuente de audio en un formato de sonido ambiental  
Dolby Digital de 5,1 canales, el audio se silenciará.  
1) Pulse el botón MENU para que la visualización del menú  
aparezca en la pantalla del televisor.  
2) Pulse el botón de flecha K o L para apuntar a "CANAL  
PREP.". Y luego pulse el botón de flecha B.  
3) Pulse el botón de flecha B para seleccionar "AGREGAR/BOR-  
RAR".  
4) Utilice el botón de flecha K o L para seleccionar el canal que  
desee memorizar o borrar de la memoria.  
NOTA: La visualización volverá a la pantalla en unos 10  
segundos. Realice la función de "AGREGAR/BORRAR" mien-  
tras aparece la visualización en la pantalla.  
Fabricado bajo licencia de Dolby Laboratories.  
“Dolby” y el símbolo con una doble D son marcas  
registradas de Dolby Laboratories. Trabajos confiden-  
ciales no publicados. ©1992-1997 por Dolby  
Pulse el botón de flecha B o s para encender el número del  
canal en AZUL CLARO si desea agregar el canal a la memoria.  
Pulse el botón de flecha B o s para encender el número del  
canal en ROJO CLARO si desea borrar el canal de la memoria.  
Laboratories. Todos los derechos quedan reservados.  
5) Pulse el botón MENU para salir del menú.  
“DTS” y “DTS Digital Out” son marcas comerciales  
de Digital Theater Systems, Inc.  
SECCIÓN DEL REPRODUCTOR DVD  
REPRODUCCIÓN DE UN DISCO  
SECCIÓN DEL TELEVISOR  
Para empezar  
1) Conecte la alimentación del amplificador o de cualquier otro  
componente que esté conectado al televisor/reproductor DVD.  
(Cambie el sistema de entrada para que se adapte al  
televisor/reproductor DVD, y compruebe que el volumen del  
sonido sea el correcto.)  
PREPARACIÓN PARA LA UTILIZACIÓN  
Para empezar  
1) Conecte el cable de alimentación a una toma de CA estándar.  
NOTA: Si aparecen algunos dígitos en la esquina de la pantalla,  
2) Pulse el botón POWER.  
pulse el botón POWER sin desconectar el cable de alimentación.  
La alimentación se conectará.  
3) Pulse el botón SELECT del mando a distancia hasta que "DVD"  
aparezca en la pantalla. Luego pulse el botón DVD.  
2) Pulse el botón POWER para encender el televisor/reproductor  
DVD.  
3) Pulse el botón SELECT del mando a distancia hasta que el  
número del canal o "TV" aparezca en la pantalla.  
Luego pulse el botón TV.  
REPRODUCCIÓN DE UN DVD VIDEO O  
UN CD DE AUDIO  
SELECCIÓN DE IDIOMA  
Si desea cambiar el idioma del menú en pantalla, siga el proced-  
imiento siguiente.  
1) Pulse el botón MENU para que la visualización del menú  
aparezca en la pantalla del televisor.  
2) Pulse el botón de flecha K o L para apuntar a "LANGUAGE".  
3) Seleccione "ENGLISH" = inglés, "ESPAÑOL" o FRANÇAIS =  
francés utilizando el botón de flecha B o s.  
4) Pulse el botón MENU para salir del menú.  
NOTA: El idioma de la visualización en pantalla deberá selec-  
cionase para el modo del televisor y el modo de DVD.  
DVD  
CD  
1) Pulse el botón OPEN/CLOSE.  
La bandeja del disco se abrirá.  
2) Ponga un disco en la bandeja.  
Asegúrese de que el disco esté bien colocado en la bandeja, con  
la cara de la etiqueta hacia arriba.  
3) Pulse el botón PLAY.  
La bandeja se cerrará automáticamente, y la reproducción  
empezará desde el primer capítulo o la primera pista del disco.  
Usted necesitará pulsar PLAY sólo cuando la bandeja haya sido  
cerrada pulsando el botón OPEN/CLOSE.  
Cuando reproduzca un DVD que tenga grabado un menú de  
títulos, el menú podrá aparecer en la pantalla. En este caso, con-  
sulte "UTILIZACIÓN DEL MENÚ DE TÍTULOS".  
PREAJUSTE DE CANALES  
Para preajustar un canal o cambiar un canal preajustado, siga el  
procedimiento siguiente.  
1) Pulse el botón MENU para que la visualización del menú desa-  
parezca de la pantalla del televisor.  
4) Pulse el botón STOP para detener la reproducción.  
NOTAS:  
Durante la operación puede aparecer un "icono de prohibición"  
2) Pulse el botón de flecha K o L para apuntar a "CANAL  
PREP.". Y luego pulse el botón de flecha B.  
3) Pulse el botón de flecha K o L para apuntar a "AUTOPRESE-  
LEC.". Luego, pulse el botón de flecha B.  
El sintonizador explora y memoriza todos los canales activos en su  
área.  
en la parte inferior derecha de la pantalla del televisor, avisán-  
dole que el televisor/reproductor DVD o el disco han encontra-  
do una operación prohibida.  
Si un disco está sucio o tiene rayas, las imágenes pueden apare-  
cer distorsionadas y la operación de reproducción tal vez se  
detenga. En tales casos, limpie el disco y desenchufe el cable de  
alimentación, y luego vuelva a conectarlo antes de reanudar la  
reproducción.  
Con DVDs que utilicen algunos títulos para reproducir señales  
de programas, la reproducción tal vez empiece desde el segundo  
título, o puede que omita estos títulos.  
Suponga que la unidad esté apagada o en otro modo que DVD.  
Pulse el botón PLAY u OPEN/CLOSE de la unidad, y la unidad  
se pondrá en el modo DVD para reproducir DVDs.  
Para poner en funcionamiento el reproductor DVD, pulse el  
botón PLAY u OPEN/CLOSE.  
El televisor distingue entre los canales de televisión estándar y  
los canales de televisión por cable.  
Cuando termine la acción de AUTOPRESELEC., el canal mem-  
orizado más baja volverá a aparecer en la pantalla.  
Cuando pulse el botón de flecha K o L después de seleccionar  
AUTOPRESELEC., el sintonizador se detendrá en los canales  
memorizados solamente.  
El televisor puede reconocer si los canales de televisión son  
CATV por las condiciones de la recepción. En este caso, intente  
de nuevo la acción de AUTOPRESELEC. en condiciones de  
recepción fina.  
- 41 -  
ES  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UTILIZACIÓN DE LOS MENÚS DE DVD  
DVD  
Algunos DVDs tienen sus propios menús como, por ejemplo, un  
menú guía que describe el contenido del disco o un menú de selec-  
ción para seleccionar el sonido, el idioma y otros ajustes personal-  
izados.  
1) Pulse el botón MENU.  
El menú DVD aparecerá.  
2) Seleccione el título deseado.  
Pulse los botones de las flechas (K/L/B/s) para cambiar el  
ajuste, y luego pulse el botón ENTER.  
3) La reproducción empezará desde el título seleccionado.  
UTILIZACIÓN DEL MENÚ DE TÍTULOS  
DVD  
Con un DVD que tenga un menú de títulos, usted podrá selec-  
cionar los títulos deseados en el menú.  
1) Pulse el botón TITLE.  
El menú de títulos aparecerá.  
2) Seleccione el título deseado.  
Pulse los botones de las flechas (K/L/B/s) para cambiar el  
ajuste, y luego pulse el botón ENTER.  
RECUPERACIÓN DE UNA PANTALLA DE MENÚS  
DURANTE LA REPRODUCCIÓN  
Para DVDs  
Pulse el botón MENU para recuperar el menú del DVD.  
Pulse el botón TITLE para recuperar el menú de títulos.  
NOTA:  
El contenido de los menús y las operaciones con menús corre-  
spondientes pueden cambiar según los discos, Consulte el man-  
ual entregado con el disco para conocer detalles.  
- 42 -  
ES  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MEMO  
- 43 -  
ES  
0C28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as fol-  
lows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original  
retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail  
purchase.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be  
required together with the product to obtain service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was  
attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does not apply to any product not pur-  
chased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage  
which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage  
which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commer-  
cial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY  
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT  
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS  
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL  
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MER-  
CHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRE-  
SENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER.  
THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI AUTHORIZED SERVICE FACILITY.  
WHEN YOU ARE RETURNING THE PRODUCT FOR SERVICE TO THE FACTORY SERVICE CENTER, PLEASE CON-  
TACT THE FUNAI SERVICE DEPARTMENT TO RECEIVE A R.A. (REPAIR AUTHORIZATION) NUMBER PRIOR TO  
SHIPPING. ANY POSTAGE, INSURANCE AND SHIPPING COST, INCURRED IN PRESENTING OR SENDING YOUR SYLVA-  
NIA PRODUCT FOR SERVICE ARE SHIPPER’S RESPONSIBILITY.  
CAREFULLY PACK WITH PROPER PACKING MATERIALS, PREFERABLY IN THE ORIGINAL CARTON AND IF NEEDED  
DOUBLE BOX IT.  
ATTACH WRITTEN DOCUMENTATION DETAILING THE COMPLAINT, TO THE OUTSIDE OR INSIDE OF THE CAR-  
TON.  
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF OF  
PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL BE CHARGED.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS THAT VARY FROM  
STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION  
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE.  
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or  
write to the following:  
FUNAI CORPORATION  
Factory Service Center  
100 North Street; Teterboro, NJ 07608  
Tel :1-800-968-3429  
Printed in China  
0EMN01733  
TD203UD * * * * *  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Microphone SM31FH User Manual
SIIG Network Card B5350 User Manual
Snapper Lawn Mower 1690047 User Manual
Snapper Lawn Mower ZF2200K User Manual
Sony Speaker XS 6038MK3 User Manual
Sony Stereo Receiver HS 703 User Manual
Sony VCR 45P User Manual
Southbend Lathe SB1001 User Manual
SVA Flat Panel Television VR3208W User Manual
Symphonic CRT Television ST427F User Manual