SEKONIC
STUDIO DELUXE II L-398M
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Features........................................................................................................2
Specifications................................................................................................4
Part Designations.........................................................................................5
Accessories..................................................................................................6
Basic Operation of Meter Unit.....................................................................7
1. Stopper Button Operation.............................................................7
2. Zero Position Check and Adjustment...........................................7
Standard Accessory Operation....................................................................8
Incident Light Measurement.........................................................................8
1. Lumisphere......................................................................................8
2. Lumidisc..........................................................................................11
Reflected Light Measurement......................................................................12
1. Lumigrid..........................................................................................12
Other Operations..........................................................................................13
1. Exposure Value (EV number) Readout..........................................13
2. Employing Cine Scale.....................................................................14
3. Using Exposure Multipliers(-2,-1,+1,+2) .....................................15
Employing Special Accessories..................................................................15
1. Direct Reading Slides.....................................................................15
2. Direct Reading Slide Application...................................................16
Measurement Examples with Various Subjects..........................................17
1. Portrait Photography......................................................................17
2. Typical Scenery .............................................................................18
3. Observatorial Scenes....................................................................18
4. Snow Scenes..................................................................................20
5. Scenes with Side or Back Lighting ...............................................21
6. Silhouette Photography.................................................................22
Applications Summary..................................................................................23
1. Special Features of the Studio Deluxe ...........................................23
2. Illumination Contrast.......................................................................24
3. Reflected Light Measurement........................................................26
4. Illumination Adjustment....................................................................29
5. Close-ups.........................................................................................31
Handling Cautions........................................................................................34
Download from Www.Somanuals.com. All Manuals Search And Download.
Nearly all photographic subjects combine complex variations of strongly reflecting
surfaces (high reflectivity) and weakly reflecting surfaces (low reflectivity). These
variations delicately influence exposure determination and to which portion the exposure is
set becomes
photograph.
a
vital factor that considerably affects the appearance of the finished
Although risk of failure can be minimized by taking maximum and minimum readings of all
portions of the subject, then averaging the values, such an approach is both time
consuming and tedious. The Studio Deluxe II is the answer to this problem. It is designed
around a standard reflectivity of 18%, which has been derived through measurements of
various subjects throughout the seasons of the year.
Consequently, high effectiveness is displayed with subjects possessing reflectivities in the
neighborhood of 18% (people, buildings, etc.) and when this can be considered the
average value (street snapshots, trees, forest scenes, etc.).
1. Optimum exposure meter for incident light measuring method (also applicable for
reflected light method).
2. Freely rotatable light sensor section for very easily performed measurements.
3. Meter stopper mechanism allows operation while hand is released from meter.
4. Meter release mechanism is also included which allows the needle to deflect freely.
This provides greater convenience when determining light balance.
5.
Memo pointer enables easier light balance setting.
6. Lumisphere detects the same light as strikes the subject. Since subjects are normally
3-dimensional, according to the lighting conditions, brighter surfaces (highlights) and
darker surfaces (shadows) are produced (illumination contrast). The Studio Deluxe II
mechanism automatically takes into account the strength of ilght from all directions,
causing the meter to indicate
a
value applicable to photography. It is thus most
convenient for determining typical exposures.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
7. After combining film sensitivity and shutter speed, direct reading slides
(optional) can be used for directly determining the aperture value.
8. Selenium photocell is employed as light sensing element, eliminating need for
battery.
9. Wide selection of available accessories allows numerous photographic
techniques to be enjoyed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Measuring System
Incident light (reflected light system
also capable)
Measuring Range
Measuring Accuracy
ISO Scale
At ISO 100, EV 4-1 7
Within ± 0.3 EV (1/3f stop)
6 - 12000
Shutter Scale
Aperture Scale
Cine Scale
60 - 1 /8000 second
0.7-128
8 fps - 128 fps
EV Scale
1 20 (exposure value)
C = 340 K = 1 2.5
112 x 58 x 34 mm
Approx. 190 grams
Calibration Constant
Dimensions
Weight
(NOTE) The outlooks and specifications described in this booklet shall be
changed without pre-advice, if necessary.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
High (H) slide
Lumisphere
Lumidisc
Optional Accessories
(sold separately).
Direct reading slides.
Lumigrid
Total of 11 direct reading slides (set of 11
slides in case). e;
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Stopper Button Operation
If the stopper button
is press-
ed when the stopper button mark
the meter needle
is set to
deflects according to bright-
ness. Then when the button is released,
the needle remains fixed at the indicated
position.
By holding the stopper button depressed
and turning it clockwise so that the mark
position becomes
the needle is released.
At this time, the meter will deflect freely
even if the stopper button is released. To
fix the needle, turn the stopper button
counter-clockwise to where the
mark is positioned
With stopper button in released
position, cover light sensor
with hand or black cloth to completely
block light. Check that
meter needle
correctly indi-
cates zero position. If the indication
deviates from zero, while observing
meter indication, use a coin or similar tool
to turn the
rear zero adjust screw
and
adjust for zero indication.
Download from Www.Somanuals.com. All Manuals Search And Download.
Incident Light Measurement
1. Lumisphere
a. Mount Lumisphere
sensor
To
white dots of Lumisphere frame and light
sensor, then turn Lumisphere carefully
clockwise to secure.
b. Set film sensitivity knob
to sensitivity value of employed film. Set
ISO value to right
side ISO mark
Photo shows setting for ISO 100.
c. From position where subject is
to be measured, point Lumi-
in direction of
sphere
camera. (Light sensor
be turned freely.)
d. Hold meter erect and press
stopper button
Meter
8
Download from Www.Somanuals.com. All Manuals Search And Download.
needle
deflects according
to brightness. When the stopper button is
released, the meter needle becomes fixed
at the deflected position. If the location is
excessively bright and the meter needle
deflects beyond scale, insert the High
slide
e. Read the footcandle indication
of the meter needle.
f. Transfer footcandle value to
the dial scale
dial ring
and set the
scale mark. If the High slide
has been inserted, set the
mark.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
g. At this time, the shutter speed scale
and aperture scale
combination becomes the correct exposure.
Example: With High slide inserted, meter indicates 80 footcandles At ISO 100, the proper
exposure becomes 1, 250 sec at F 5.6, 1; 30 sec at F!16 and 1 sec at F-90. h. By
changing ISO setting, the set combination of shutter speed and aperture scale is
automatically altered to the appropriate one corresponding to the changed ISO value.
* Meter scale intermediate values
intermediate values for
shutter speed and aperture
scale
* Film sensitivity intermediate values
Note: When no slide is inserted, strong light
directly striking the slide slot may enter
through the slot. Although this does not
seriously affect exposure, if more accurate
exposure is required, cover slot with hand.
1 c'.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Lumidisc. Employ for illumination contrast
Adjustment and luminance measurement.
· Contrast measurement
a. Mount Lumidisc
sensor
Install in the same
manner as Lumisphere.
b. Hold meter at subject position
and point Lumidisc
directly toward center of main light.
c. Press stopper button
read meter scale footcandle
indication
d. Turn the memo pointer dial and set the
pointer
1
7
at the footcandle value the
needle points to
e. In the same manner, measure the fill-in
light. In this case, use care that light from
main source dose not enter sensor.
f. Read
a
difference
between
the
footcandle value the pointer is set (see
above c) and the one for fill-in light (=
needle position.
Ratio between main and fillip light
footcandles becomes the contrast ratio.
Example:
With main light at 640
footcandles, fill-in light reads
320 footcandles. Illumination
contrast ratio becomes:
640
320
2
1
or 2 : 1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
e. Press stopper button
and
read meter scale footcandle
indication
. However, since
footcandles are units of incident light
only, this value becomes simply a
reference.
f. Transfer indicated value to dial
scale
Rotate the dial ring
mark
and set
g. At this time, shutter speed
scale
and
aperture
combination becomes the
correct exposure.
Note:
Do not employ slides for reflected
light measurement.
* More accurate results can be obtained for
reflected light measurement by using
a
standard
reflectance
slide
(optional
accessory).
Other Operations
1. Exposure Value
(EV) number Readout
Reading this exposure value to perform
setting becomes convenient for cameras
which employ a light value system shutter and
aperture combination.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Read meter needle
candle indication
foot-
b. Transfer this number to the
dial scale
and set
Rotate dial ring
scale mark
If the High slide is inserted, set
the mark
c. EV value indicated by EV
mark
becomes the correct
exposure value.
2. Employing Cine Scale
Incident and reflected light
measurements during cine pho-
tography are performed in the
same manner as described pre-
viously. However, since the cine
scale
cine camera film speed, read the
aperture scale
numerals correspond to
indication that
pertains to the employed film speed.
Note: Some cine cameras possess faster exposure times due to a narrower
rotating shutter angle (angle of light transmitting portion). It is important to
know the accurate film speed versus shutter angle value for your camera
in order to determine proper exposure. Refer to the camera operating
instructions, maker's catalogue, etc. for shutter speed information.
Shutter angle and exposure calculation:
Note: Standard theatrical cine film speed is 24 fps at 1/50 sec.
This position is indicated by a red line on the scale.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Using Exposure Multipliers (-2, -1, +1, +2)
Exposure multiplier indications are provided at both sides of the
marks of the dial scale. Use the -1 or -2 mark when desir
ing to cut the exposure to 1!2 of 1!4 and +1 or +2 mark to multiply the exposure by 2 or 4.
Set the appropriate mark, instead of the or, to the dial scale value.
EMPLOYING SPECIAL ACCESSORIES
1. Direct Reading Slides
A total of 11 slides are available, all of which may be used together with the Lumisphere
and Lumidisc. (Note that they cannot be used with Lumigrid.) The High slide, as
mentioned previously, is employed for varying the measuring range in 2 steps (high and
low illumination), however, it can also be used for direct reading. The other slides are
specialized for direct reading and cannot be used for mode selection.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: One set of slides consists of slide numbers 1 - 11 in a case. The High slide
can also be used as a direct reading slide.
2. Direct Reading Slide Application
When photographing, select slide from
the above table according to film
sensitivity and shutter speed. Insert slide
and perform measurement in the same
manner as for incident light. Read
directly the
aperture value
the meter needle
* Since it is not necessary to rotate the dial when employing direct reading slides,
setting becomes extremely fast and convenient.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MEASUREMENT EXAMPLES WITH VARIOUS SUBJECTS
1. Portrait Photography
There are various kinds of human subject photography. In a case, for example, of a
skier against a snowy mountain background, the human subject simply becomes a
picture detail and for the purpose of determining the exposure, this cannot be
considered portrait photography. In the final analysis, portrait photography is when
the human subject is in the center of the picture and the exposure adjusted to him.
In addition, camera to subject distance must be considered, whether the picture is to
be one person or a group.
Measurement by incident light (Lumisphere installed) displays high effectiveness in
portrait photography. Perform measurement as described in the section on Incident
Light Measurement. After setting the proper exposure for the human subject,
lighting conditions do not present a problem and subject detail is preserved even
under back lighting.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Typical Scenery
In the case of scenery, measure by using the Lumisphere at the camera position (refer to
section on Incident Light Measurement). Although the previously described standard
holding method is adequate, if lighting conditions of subject and camera positions are
dissimilar, move the meter to a position where conditions are the same type as those of the
subject and point in
a
direction parallel to the camera optical axis. If the subject is
shadowed, either move the measuring position to the same type of location or reproduce
the same conditions with the hand or other means. Portrayals of buildings etc. can be
considered as general middle distance scenery, while main subjects can be treated in the
same manner as described in the section on Portrait Photography.
3. Observatorial Scenes
This refers to the situation where a distant object in the subject field forms an important part
of the pictured scene.
Examples: Observatories, distant views, etc.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Distant scenes are subject to haze due to atmospheric effects on light and can be
easily overexposed. For this reason, first use the Lumisphere and measure by
standard method from the camera position. Then point the Lumisphere toward the
sun and measure. Determine exposure from the mean of the two obtained values.
Note: To obtain the mean of the two values, perform as follows.
Transfer mean value of the two footcandle indications (aperture
scale) to the dial.
Example: If 320(8) footcandles and 80(4) footcandles are obtained,
the mean value becomes 160(5.61. In the case of 80(4)
and 40(2.8) footcandles, the intermediate becomes the
desired value. Consequently, transfer that value to the
dial.
Transfer each footcandle value to the dial to obtain exposure. In cases of the
same aperture, setting the shutter speed to the average is acceptable.
Memo pointer is useful for memorizing the first measured value.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Snow Scenes
a. Many cases of problems occur with reflected light measuring methods due to snow
surface glare. Using incident light measurement eliminates these concerns. Freshly
fallen snow possesses a reflectivity of approximately 73%, while even after several
days in urban areas, this declines only to about 60%. Compensation must therefore
be performed. Measurement by standard method
is reduced by
Example:
Note 1 :
Note:2:
Reduce as much as possible since overexposed snow can
take on a flour-like appearance without luster in the
finished photograph.
compensation amount is based on the re-
flectivity value of snow. This may vary according to snow
quality and soiling.
Download from Www.Somanuals.com. All Manuals Search And Download.
0Note 3:
In situations with direct or top lighting
(sun near zenith), the Lumisphere will
detect reflected light from the snow
surface. Some means of blocking the
light from below becomes required in this
case.
b. In some cases, good results can be obtained with reflected light measurement
under back light conditions, cloudy snow scenes where glare is less and snow
scenes under direct lighting. Install Lumigrid and point light sensor slightly
downward to block light from the sky, then from camera position, aim toward
subject
and measure. Be sure to set the
mark at this time and do not
employ slides.
5. Scenes with Side or Back Lighting
Download from Www.Somanuals.com. All Manuals Search And Download.
In typical cases of back and side lighting, although the surface of a 3-dimensional
subject facing the camera becomes dark, a portion is usually strongly lighted. Even
though standard measurement with the Lumisphere can bring out detail of the
darker portions, on occasion, the brighter portions can become overexposed and
difficult to see. In some instances, this effect can even be enhanced to produce a
special photographic composition, but for a generally more attractive result,
perform as follows. First use the Lumisphere and measure by standard method,
then determine exposure from the mean value (same technique as used for
Observatorial Scenes).
6. Silhouette Photography
In situations such as a silhouette of a person, tree or bridge in the foreground
against the setting sun and brilliantly shining sky as background, remove slide and
point Lumisphere toward the setting
sun to measure (as with Reflected Light Measurement). Then
without inserting High slide, set to
mark. In this manner, the
foreground becomes silhouetted by underexposing the light source.
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONS SUMMARY
1. Special Features of the Studio Deluxe 11
As the Studio Deluxe ll is
a
high precision measuring instrument, by fully utilizing its
capabilities, its special functions can be displayed covering an additionally wide range of
applications. Incident light measurement is an extremely practical method in actual
photographic situations and is often employed by professional photographers and
cinematographers. Since proper exposure can be determined even in cases where errors
are easily incurred with reflected light measurement, it is extremely convenient for both
color and monochrome.
The Lumisphere displays its optimum value when used for incident light measurement
during color or monochrome photography of fleshtones (portrait photography in which
fleshtones are considered as the main picture element for determining exposure). Since
good or bad quality portrayals can be discerned even by amateurs, fleshtones become the
only true standard in color photography. (They can also be given a wider range of artistic
expression than visible to the naked eye.)
Well known basic principles form the foundation of the Studio Deluxell, however, plenty of
latitude is provided for obtaining special effects. By allowing variations in exposure to be
performed, exactly the same reproductions become possible as those learned only from
experience. Utilizing the selection of accessories also opens the way to the multitude of
applications described in the preceding pages.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Illumination Contrast
Light balance measurements are the most important application of the Lumidisc. This
consists of measuring the ratio of main light and fill in light in order to perform vital
adjustments when photographing an illuminated subject. The photographer is advised to
record the data obtained for his particular equipment. This will provide ready reference in
the future and allow the same lighting conditions to be reproduced.
When shooting in a studio or similar situation where artificial lighting equipment is used,
more attractive results can be produced by making the main and fill in light ratio 4 : 1 - 2 :
1. Also when using reflectors either indoors or outdoors, determine the exposure after
measuring the illumination ratio.
Normal sunlight becomes the main light source outdoors, while white or silver reflectors are
used to brighten shadow portions of the subject. In this situation, install the Lumidisc, point
it toward the sun and read the indicated value. Turn the memo pointer dial and set the
pointer 17 at the read value. Next, point the Lumidisc toward the reflector (shield with hand
to avoid sunlight) and again read the indicated value. To obtain maximum color effect, this
fill in light source should be 1/2 - 1/4 of the main lignt.
An additional theatrical effect can be produced with monochrome by using
a
higher
illumination ratio. It is suggested, for example, to use
sunlight of 1/16 or lower.
a
ratio between fill in light and
If the meter needle deflects beyond scale, use the H slide and as described earlier, multiply
the indicated value by 32. Then calculate main and fill in lighting (see section on *Contrast
measurement).
After completing light balance adjustment, replace Lumisphere and measure exposure by
normal method. At this time, hold the Lumisphere close to the subject to fully detect
sunlight and fill in light.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fill in light measurement
Main light measurement
Use white or silver reflector to brighten
shadow portions of subject.
Exposure measurement
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Illumination ratio can be
varied by keeping the main
light fixed and varying the fill
in light.
Reflected Light Measurement
Reflected light measurement is employed for the following purposes.
a. Luminance range adjustment.
b. Self-lighted subjects such as neon signs which can only be measured by reflected light
method and locations such as show windows where meter cannot be brought into proximity
with subject to allow incident light method.
Measurement in these type situations in described below.
1. Luminance range center point
Refers to measuring subject luminance by reflected light method. This luminance varies
somewhat according to incident light strength and surface reflectivity of the subject.
Incident light becomes measured by taking the standard surface reflection as 18%, from
which the exposure value is determined.
To obtain accurate exposures, the Lumisphere is used to measure effective footcandles to
determine the Luminance center point.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Shown here is an example of using
Lumisphere and by normal measuring
method without slide, meter needle
indicates 640 footcandles. With film
sensitivity of ISO 100, exposure
becomes f 45
and shutter speed 1 second. mark at
this time indicates 20.
This 20 indicates the exact center point of the luminance range. In the same
condition, install Lumigrid and when standard reflectivity of 18% is measured, this
means that the dial scale will indicate 20. When determining exposure by using the
Lumisphere or Lumidisc,
the
mark will always indicate the center of luminance range,
regardless of whether or not the High slide is inserted.
If the measured value is set to the dial scale
mark and the
mark dose not reach the scale, reflected light measurement
with the Lumigrid cannot be performed due to insufficient incident light strength. In
other words, if the incident light is less than 160 footcandles, reflected light
measurement cannot be performed with the Lumigrid.
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Hold meter about 15cm from the subject, point Lumigrid to each surface of the
subject and read the footcandle scale value.
c. To determine the luminance range, it is sufficient to divide the highest meter
indication by the lowest. For example, if the highest value is 80 and the lowest 5, the
luminance range becomes 80/5 = 16/1 or 16 : 1.
Luminance range measurement
3. To obtain superior color photographs, determine upper and lower limits.
a. Adequate color photographs can be obtained with typical color film if within the subject
luminance distribution, the maximum is less than 4 times the center point and minimum
more than 1 /4 times (i.e.: overall luminance range becomes less than 16 : 1).
b. With
a
luminance center point of 20, if the measured maximum luminance is higher
than 80 (center point 20 x 4 = 80), color of that surface will become faded in the
photograph. Consequently, a slight reduction of incident light to this portion becomes
required.
c. Conversely,
20
photograph.
a
portion with
a
measured minimum luminance less than 5 (center point
/
4
=
5) requires increased illumination in order to obtain an acceptable color
28
Download from Www.Somanuals.com. All Manuals Search And Download.
The Studio Deluxe indicates normal color
photograph luminance range limits
corresponding to 2 f stops left and right
of the luminance range center point.
4. Illumination Adjustment
The Studio Deluxe possesses an array of functions for the performance of
illumination adjustments which were nearly unknown in earlier instruments. It
allows the shooting site to be set up quickly and accurately. Described here are set
up procedure and 29
Download from Www.Somanuals.com. All Manuals Search And Download.
examples to provide full control over movie scenes. It would not be erroneous to also apply
these to still photos.
Stage 1
Determine overall lighting strength.
a. Set meter to ISO 100 (see film
sensitivity intermediate values).
b. Set 24 red line of cine speed
scale to F/5.6.
c. At this time,
mark indication on dial scale becomes slightly
lower than 640 (footcandles). If this is taken as the meter scale position, a value of
500 footcandles (lower than 640 footcandles) becomes the required lighting strength
(see meter intermediate scale values).
Stage 2
Key light setting
a. Turn on key light (main light) and determine direction required for subject illumination.
b. Without installing slide, hold meter at the subject position, point Lumisphere toward
camera and set stopper button to released
position.
c. Adjust main light intensity or distance until meter indicates 400. The indication can
then be increased to the required 500 footcandles (determined in Stage 1c) by
applying fill in light.
Stage 3
Adjust illumination contrast
a. Install Lumidisc in place of Lumisphere.
b. Measure key light (indication should be 400 footcandles).
c. Turn on fill in light.
d. As described in section on outdoors Illumination Contrast
Adjustment, adjust fill in light to obtain suitable illumination
contrast. (For a contrast ratio of 2 : 1, the fill in light indication
must be 200 footcandles.) Lighting from back affects contrast
only slightly.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust luminance range
a. Install Lumisphere.
b. Hold meter at subject position, point Lumisphere toward camera and read needle
indication. With all lights turned on, adjust main light so that indication becomes 500
footcandles.
c.
Set
mark to 500 and read
value becomes 16 to indicate luminance range center point. If by experience the
required results can be obtained with luminance range of 16 to 1, maximum
a
a
luminance indication of 64 (center point 16 x 4 = 64) becomes the upper limit for
desired color reproduction. In this case, the minimum limit becomes 4 (center point 16
= 4 = 4). This means that attractive color reproduction cannot be obtained unless the
subject luminance distribution is within 4 ^- 64.
d. Exchange Lumisphere for Lumigrid and check if there are any locations on the subject
brighter than 64 or dimmer than 4.
Stage 5
Determine correct exposure
Although above Stage 4b includes an exposure value measurement using the Lumisphere,
perform correct exposure measurement as a final check. With the illumination controlled as
described, this should accurately become F/5.6 1/50 sec. This 5 stage procedure allows full
control of all lighting elements.
Closeups
It is essential to increase the exposure value when the subject is closer to the camera than
10 times the camera focal distance. An example of this type of case is with a camera lens
focal distance to 50mm and
a
subject distance of 40cm. The reason for this is the
increased image magnification as the subject approaches the camera. When light from the
subject passes through the lens and becomes focused on the film, the following
relationship exists among film plane illumination, subject brightness and image
magnification.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
As can be noted from the above formula, if the subject luminance is fixed and the
magnification changes, the film plane brightness (illumination) varies in the inverse
proportion (M + 1)2. With a large subject distance, M is small and this effect
becomes nearly absent, but as the subject distance decreases, M becomes larger.
In an actual photographic example, with a magnification M of 1, film plane
brightness becomes (M + 1)2 or 4. This is 1/4th that of a subject distance at infinity
and exposure must be increased 4 times. When the measured exposure value is
1/60 sec shutter speed, this must be compensated to 1/15 sec (1/60 x 4 = 1/15). In
closeup photography, (M + 1)2 is referred to as the compensation factor.
Measuring Method
Hold meter as close as possible to the subject and point Lumisphere toward the
camera. If light source is very close to the subject, temporarily remove the subject
and hold the Lumisphere in the subject position. The light then striking the
Lumisphere becomes exactly the same as that illuminating the subject. To obtain
exposure compensation for closeup:
1. Determine exposure by normal incident light method. 2. Measure
subject and image sizes (groundglass).
3. If the image is larger than the subject, it is enlarged, while a smaller image is
compressed. Divide the larger value by the smaller value.
4. Obtain compensation factor from Table 1.
5. Apply compensation factor to measured exposure value to produce
compensated exposure value.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Compensation factor = (M + 1)
Compression
Compensation
Enlargement .
Compensation
Subject to
image ratio
20 : 1
19 : 1
18 : 1
17 : 1
16 : 1
15 : 1
14 : 1
13 : 1
12 : 1
11 : 1
10 : 1
9 : 1
Subject to
image ratio
1 : 1
1 : 1.25
1 : 1.50
1 : 1.75
1 : 2
1 : 2.25
1 : 2.5
1 : 2.75
1 : 3
1 : 3.5
1 : 4
factor
1.10
1.11
1.11
1.12
1.13
1.14
1.15
1.16
1.17
1.19
1.21
1.24
1.27
1.31
1.36
1.44
1.50
1.56
1.65
1.78
1.86
1.96
2.09
2.25
2.47
2.78
3.24
4.00
Factor
4
5
6
7.5
9
10.5
12
14
16
20
25
30
36
49
64
81
100
121
144
169
196
225
256
289
324
361
400
441
1 : 4.5
1 : 5
1 : 6
1 : 7
1 : 8
8 : 1
7 : 1
6 : 1
5 : 1
4.5 : 1
4 : 1
3.5 : 1
3 : 1
2.75: 1
2.5 : 1
2.25: 1
2 : 1
1 .75 : 1
1.5 : 1
1 .25 : 1
1 : 1
1 : 9
1 : 10
1 : 1 1
1 : 12
1 : 13
1 : 14
1 : 15
1 :16
1 : 17
1 :18
1 : 19
1 : 20
33
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLING CAUTIONS
Since the Studio Deluxe ll is a high precision instrument, use ample
care in regard to the following points.
Avoid dropping or subjecting it to strong shock.
Do not store in high temperature or high humidity locations.
Do not store in areas subject to magnetic fields or where insect repellants are located
(metal cabinets, clothing dressers, etc.).
Keep Lumisphere and Lumidisc clean and protect from scratches. If severely soiled,
these can be washed in
thoroughly.
a
lukewarm solution of mild detergent. Rinse and dry
In event service is required, contact the nearest authorized service agency. If necessary to
ship the meter, be sure to surround it with at least 3cm (1-1/2") thick insulating material
and pack in a sturdy, crush resistant package.
Download from Www.Somanuals.com. All Manuals Search And Download.
SEKONIC CORPORATION
7-24-14, OIZUMI-GAKUEN-CHO, NERIMA-KU, TOKYO 178-8686, JAPAN TEL: (03) 3978-2335
FAX: (03) 3978-5229
T156270B-A
Download from Www.Somanuals.com. All Manuals Search And Download.
|