Product Manual
®
Momentus 5400.2 Blade
Server
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
100367617
Rev. B
August 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Time to ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Environmental specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Environmental protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.0
ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Momentus 5400.2 Blade Server Product Manual, Rev. B
i
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Figure 4.
Momentus 5400.2 PATA disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical 5V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Momentus 5400.2 Blade Server Product Manual, Rev. B
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate®
Momentus®5400.2 Blade Server drives:
• ST9120821AB
• ST9100824AB
• ST98823AB
• ST96812AB
• ST94813AB
These drives provide the following key features:
• 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.
• Tunneling Magnetoresistive (TMR) recording heads.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Full-track multiple-sector transfer capability without local processor intervention.
• 800 Gs nonoperating shock and 250 Gs operating shock.
• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers the
industry’s most comprehensive protection for disc drives.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
• Support for autodetection of master/slave drives that use cable select (CSEL).
Figure 1. Momentus 5400.2 PATA disc drive
Momentus 5400.2 Blade Server Product Manual, Rev. B
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate
ST9120821AB, ST9100824AB, ST98823AB, ST96812AB, and ST94813AB model drives.
2.1
Specification summary
The specifications listed in this table are for quick reference. For details on specification measurement or
definition, see the appropriate section of this manual.
Table 1:
Specifications
Drive specification
ST9120821AB ST9100824AB ST98823AB
ST96812AB
ST94813AB
Formatted Gbytes (512 bytes/sector)* 120
100
80
60
40
Guaranteed sectors
Bytes per sector
Physical read/write heads
Discs
234,441,648
195,371,568
156,301,488
117,210,240
78,140,160
512
4
4
2
3
2
2
1
2
1
2
Cache (Mbytes)
8
Recording density,
BPI (bits/inch typical)
778k
126k
Track density.
TPI (tracks/inch typical)
2
Areal density (Gbits/inch max)
98.2
Spindle speed (RPM)
5,400
Internal data transfer rate OD
(Mbytes/sec max)
42
I/O data-transfer rate
(Mbytes/sec max)
100
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–5
ATA data-transfer
modes supported
Height
9.5 +/-0.2 mm (0.374 +/-.008 inches)
Width
69.85 +/-0.25 mm (2.750 +/-0.010 inches)
Length
100.2 +/-0.25 mm (3.945 +/-0.010 inches)
Weight (typical)
100 grams (0.22 lb)
Average latency (msec)
Power-on to ready (sec typical)
Standby to ready (sec typical)
Startup current 5V (typical)
5.6
3.5
3.0
1.0 amps
Track-to-track seek time
(msec typical)
1.0 (read), 1.5 (write)
12.5
Average seek time (msec typical)
Momentus 5400.2 Blade Server Product Manual, Rev. B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1:
Specifications
Drive specification
ST9120821AB ST9100824AB ST98823AB
ST96812AB
ST94813AB
Average seek, read (msec typical)
Average seek, write (msec typical)
Full-stroke seek (msec)
12.5
14.5
22 (typical); 24 (max)
2.0 watts
Seek power (typical)
Read: 1.8 watts
Write: 1.8 watts
Read/write power (typical)
Idle mode (typical)
Standby mode
Sleep mode
0.80 watts
0.26 watts (typical)**
0.26 watts (typical)**
Voltage tolerance
(including noise)
5V ± 5%
5° to 55°C (operating)
–40° to 70°C (nonoperating)
Ambient temperature
Temperature gradient
20°C (operating)
(°C per hour max, noncondensing)
30°C (nonoperating)
Relative humidity
(noncondensing)
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
Wet bulb temperature (°C max)
Altitude, operating
30% per hour max
30°C (operating)
40°C (nonoperating)
–304.8 m to 3,048 m (–1000 ft to 10,000 ft)
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)
Altitude, nonoperating
(below mean sea level, max)
Shock, operating (Gs max at 2 msec) 250
Shock, nonoperating
800
(Gs max at 2 msec)
Shock, nonoperating
900
(Gs max at 1 msec)
Shock, nonoperating
400
(Gs max at 0.5 msec)
Vibration, operating
(max displacement may
apply below 10 hz)
1.0 Gs (0 to peak, 5–500 Hz)
Vibration, nonoperating
(max displacement may apply below
22 hz)
5.0 Gs (0 to peak, 10–500 Hz)
Drive acoustics, sound power (bels)
Idle***
2.4 (typical)
2.6 (max)
2.9 (typical)
3.1 (max)
Performance seek
14
Nonrecoverable read errors
Annualized Failure Rate (AFR)
Load/Unload (U/UL) cycles
1 per 10 bits read
1.74% at maximum case temperature of 40°C and 8,760 power on hours (POH)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Service life
5 Years
4
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1:
Specifications
Drive specification
ST9120821AB ST9100824AB ST98823AB
ST96812AB
ST94813AB
5 Years on distribution units.
To determine the warranty for a specific drive, use a web browser to access the following web
page:
Warranty
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive
serial number, model number (or part number) and country of purchase. The system will display
the warranty information for your drive.
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes
will not contribute to battery power consumption.
***During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
2.2
Formatted capacity
Model
Formatted capacity*
Guaranteed sectors
234,441,648
195,371,568
156,301,488
117,210,240
Bytes per sector
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
120 Gbytes
100 Gbytes
80 Gbytes
60 Gbytes
40 Gbytes
512
512
512
512
512
78,140,160
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
2.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
2.4
Physical organization
Model
Read/write heads
Number of discs
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
4
4
3
2
2
2
2
2
1
1
Momentus 5400.2 Blade Server Product Manual, Rev. B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5
Recording and interface technology
Technology
Specification
Interface
Parallel ATA
Recording method
RLL 0,11
Recording density BPI (bits/inch typical)
Track density TPI (tracks/inch typical)
778k
126k
2
Areal density (Gbits/inch max)
98.2
Spindle speed (RPM) (± 0.2%)
Internal data-transfer rate OD (Mbytes/sec max)
I/O data-transfer rate (Mbytes/sec max)
Interleave
5,400
42
100 (Ultra DMA mode 5)
1:1
Cache buffer
8 Mbytes (8,192 kbytes)
2.6
Physical characteristics
Height
(mm)
(inches)
9.5 +/–0.2
0.374 +/–0.008
Width
(mm)
(inches)
69.85 +/–0.25
2.750 +/–0.010
Length
(mm)
(inches)
100.2 +/–0.25
3.945 +/–0.010
Typical weight
(grams)
(pounds)
100
0.22
6
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between
random tracks, less overhead.
Typical seek times (msec)*
Track-to-track
Read
1.0
Write
1.5
Average
12.5
22.0
5.56
14.5
24.0
5.56
Full-stroke
Average latency
*Measured in performance mode
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,
regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.
However, due to the manner in which these drives are formatted, benchmark tests that include command
overhead or measure logical seeks may produce results that vary from these specifications.
2.8
Time to ready
Max @ 25°C
Time to ready
Typical
3.5
Power-on to Ready (sec)
Standby to Ready (sec)
8.0
8.0
3.0
Momentus 5400.2 Blade Server Product Manual, Rev. B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9
Power specifications
The drive receives DC power (+5V) through the interface connector.
2.9.1 Power consumption
Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on
an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature.
• Spinup power
Spinup power is measured fromthe time ofpower-onto thetimethat the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on
three random seek operations every 100 msecs. This mode is not typical.
• Read/write power and current
Read/write power is measured with the heads on track, based on three 63 sector read or write operations
every 100 msecs.
• Idle mode power*
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down model
Table 2:
DC power
Power dissipation
Spinup (typical)
Seek
+5V average (watts, 25° C)
1.0 amps
2.00
1.8
Read
Write
1.8
Idle, performance mode*
Idle, active*
Idle, low power mode*
Standby
1.70
0.99
0.80
0.26
0.26
Sleep
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
8
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9.1.1
Typical current profile
Figure 2. Typical 5V startup and operation current profile
2.9.2
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +5 volt line.
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.
2.9.3
Voltage tolerance
Voltage tolerance (including noise):
5V ± 5%
Momentus 5400.2 Blade Server Product Manual, Rev. B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10
Environmental specifications
Ambient temperature
2.10.1
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 40°C (104°F) within the operating ambient conditions.
Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Operating
5° to 40°C (41° to 104°F)
Nonoperating
–40° to 70°C (–40° to 158°F)
2.10.2
Temperature gradient
Operating
20°C per hour (68°F per hour max), without condensation
30°C per hour (86°F per hour max), without condensation
Nonoperating
2.10.3
Humidity
2.10.3.1
2.10.3.2
2.10.4
Relative humidity
Operating 5% to 90% noncondensing (30% per hour max)
Nonoperating 5% to 95% noncondensing (30% per hour max)
Wet bulb temperature
Operating 30°C (86°F max)
Nonoperating 40°C (104°F max)
Altitude
Operating
Nonoperating
–304.8 m to 3,048 m (–1,000 ft to 10,000 ft)
–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)
10
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10.5
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
2.10.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more
than two times per second.
2.10.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse
of 2 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 900 Gs based on a nonrepetitive half-sine shock pulse
of 1 msec duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse
of 0.5 msec duration.
2.10.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.10.6.1
Operating vibration
The following table lists the maximum vibration levels that the drive may experience while meeting the perfor-
mance standards specified in this document.
5–500 Hz 1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.
2.10.6.2
Nonoperating vibration
The following table lists the maximum nonoperating vibration that the drive may experience without incurring
physical damage or degradation in performance when subsequently put into operation.
5–500 Hz
5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.
Momentus 5400.2 Blade Server Product Manual, Rev. B
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-
surements are consistent with ISO document 7779. Sound power measurements are taken under essentially
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is
defined by the following equation:
(Number of seeks per second = 0.4 / (average latency + average access time)
Table 3:
Drive level acoustics
Acoustic mode
Idle*
Performance Seek
2.3 bels (typ)
2.6 bels (max)
2.9 bels (typ)
3.1 bels (max)
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
2.12
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the rradio frequency (RF) environments defined in the following table:
Table 4:
Electromagnetic immunity
Performance
level
Reference
standard
Test
Description
Electrostatic discharge
Radiated RF immunity
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
A
EN 61000-4-2: 95
EN 61000-4-3: 96
80 to 2,000 MHz, 10 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz
ENV 50204: 95
Electrical fast transient
Surge immunity
± 1 kV on AC mains, ± 0.5 kV on external I/O
± 1 kV differential, ± 2 kV common, AC mains
B
B
A
EN 61000-4-4: 95
EN 61000-4-5: 95
EN 61000-4-6: 97
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz
sine
Power Frequency H-field 1 A/m, 50Hz/60Hz, 3 axes
immunity
A
EN 61000-4-8: 97
EN 61000-4-11: 94
Voltage dips, interrupts
30% Reduction for 25 cycles
>95% Reduction for 250 cycles
>95%, 0.5 cycles
C
C
B
A - 1) No upset or degradation in performance beyond manufacturer’s specified limits.
2) No data loss.
B - 1) Unit self recovers without user intervention.
2) No data loss.
C - 1) Upset OK provided that unit will function after user intervention.
12
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
2.13
Reliability
Measurement type
Specification
14
Nonrecoverable read errors
Annualized Failure Rate (AFR)
Load/Unload (U/UL)
1 per 10 bits read, max.
1.74% at maximum case temperature of 40°C and 8,760 power on hours (POH).
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Service Life
Warranty
5 Years
5 Years on distribution units.
To determine the warranty for a specific drive, use a web browser to access the fol-
lowing web page:
From this page, click on the “Verify Your Warranty” link. You will be asked to pro-
vide the drive serial number (or part number) and country of purchase. The system
will display the warranty information for your drive.
2.14
Agency certification
2.14.1
Safety certification
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections
of IEC950 and EN 60950 as tested by TUV North America.
2.14.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-
tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and
the immunity levels are defined by EN 55024.
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators
should confirm EMC compliance and provide CE marking for their products.
Momentus 5400.2 Blade Server Product Manual, Rev. B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Korean RRL
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-
graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information
and Communication Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-
ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-
nized lab.
• EUT name (model numbers): ST9120821AB. ST9100824AB, ST98823AB, ST96812AB, and ST94813AB.
• Certificate numbers:
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
E-D011-04-3510(B)
E-D011-04-3506(B)
E-D011-04-3503(B)
E-D011-04-3502(B)
E-D011-04-3504(B)
• Trade name or applicant: Seagate Technology International
• Manufacturing date: June 2005
• Manufacturer/nationality: Seagate Technology International
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-
cation Authority (ACA).
2.14.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-
keted to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installa-
tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
14
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-
gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-
ber 004-000-00345-4.
2.15
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the
rep-resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disc drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard operat-
ing procedures that ensure that restricted substances are not utilized in our manufacturing operations, labora-
tory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
2.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent ot 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment. Users
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,
copper, nickel, and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-
nized rubber, that can outgas corrosive compounds should be minimzed or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Momentus 5400.2 Blade Server Product Manual, Rev. B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
• The drive is fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
Momentus 5400.2 Blade Server Product Manual, Rev. B
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2
Jumper settings
3.2.1
Master/slave configuration
Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the
4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable
The “Master or single drive” option is the factory default setting.
Drive is master (or single drive)
Drive is slave
Cable select
Figure 3. Jumper settings
3.2.2
Cable-select option
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,
CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To
enable cable select, set a jumper as shown in Figure 3. Refer to your computer manual to determine whether
your computer supports this option.
18
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. See Figure 4 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow
these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only M3 x 0.5 mounting screws.
• Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).
• Four (4) threads (0.080 inches) minimum screw engagement recommended.
1
2
3
DIMENSIONS PER EIA-720 OR SFF 8201 SPECIFICATION.
DIMENSIONS PER SFF 8212 OR SFF 8223.
DRIVE LENGTH W/ PATA IS 3.945 .057 (WORST CASE).
DRIVE LENGTH W/ SATA IS 3.957 .062 (WORST CASE).
3.945
.010
(BASE)
( .490
.217
.217
)
.050
.050
2
.157
2
.399
( .673
)
C
OF CONN.
DATUM B
OF DRIVE
C
1
2.750
.010
(BASE)
( .189
)
2
SATA
PATA
3
3.567
1
.551
1
2X M3 X 0.5-6H
.020
)
(
MOUNTING HOLES; BOTH SIDES
.12 MIN FULL THREAD
0.148 .010 X 90
1
.374
-D-
.008
SECTION B-B (SATA)
2X .118
BOTH SIDES
1
.039
B
C
D
4X M3 X 0.5-6H
3.567
(BASE)
MOUNTING HOLES; BOTH SIDES
.10 MIN FULL THREAD
0.148 .010 X 90
1
.551
1
1
2
.152
.399
2
DETAIL A (PATA)
B
1
2.430
.039
.016
B
C
D
C
B
-B-
2
.012
.370
2
1
.160
DETAIL A
-C-
DETAIL A (SATA)
Figure 4. Mounting dimensions—top, side and end view
Momentus 5400.2 Blade Server Product Manual, Rev. B
19
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0
ATA interface
These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports
ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The
drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.
For detailed information about the ATA interface, refer to the draft of AT Attachment with Packet Interface
Extension (ATA/ATAPI-6), NCITS T13 1410D, subsequently referred to as the Draft ATA-6 Standard.
4.1
ATA interface signals and connector pins
The following table summarizes the signals on the 44-pin ATA interface connector. For a detailed description of
these signals, refer to the Draft ATA-6 Standard.
Table 5:
Connector signals
Connector
Contact
Cable
Conductor
Cable
Conductor
Connector
Contact
Signal Name
Signal Name
RESET-
DD7
1
1
2
2
Ground
DD8
3
3
4
4
DD6
5
5
6
6
DD9
DD5
7
7
8
8
DD10
DD4
9
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
DD11
DD3
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
DD12
DD2
DD13
DD1
DD14
DD0
DD15
Ground
DMARQ
DIOW-
DIOR-
IORDY
DMACK-
INTRQ
DA1
(keypin)
Ground
Ground
Ground
PSYNC:CSEL
Ground
IOCS16-
PDIAG-
DA2
DA0
CS1FX-
DASP-
+5 V (Logic)
CS3FX-
Ground
+5V (Motor)
No connection
Ground (Return)
43
Momentus 5400.2 Blade Server Product Manual, Rev. B
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.1
Supported ATA commands
The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA
commands, refer to the Draft ATA-6 Standard.
Table 6:
Supported commands
Command name
Command code (in hex)
ATA-standard commands
ATA Device Configuration Overlay
ATA Service
B1
A2
H
H
Check Power Mode
Download Microcode
Execute Device Diagnostics
Flush Cache
98 E5
H,
H
92
90
H
H
E7
H
Flush Cache Extended
Format Track (Legacy)
Identify Device
EA
H
50
H
EC
H
Idle
97 E3
H,
H
Idle Immediate
95 E1
H,
H
Initialize Device Parameters
Read Buffer
91
H
E4
H
Read DMA
C8 C9
H,
H
Read DMA Extended
Read Log Extended
Read Multiple
25
22
H
H
C4
H
Read Multiple Extended
Read Native Max Address
Read Native Max Address Extended
Read Sectors
29
H
F8
H
H
27
20 21
H,
H
Read Sectors Extended
Read Verify Sectors
Read Verify Sectors Extended
Recalibrate
24
H
40 41
H,
H
42
10
H
H
Security Disable Password
Security Erase Prepare
Security Erase Unit
Security Freeze Lock
Security Set Password
F6
F3
F4
F5
F1
H
H
H
H
H
22
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6:
Supported commands
Command name
Security Unlock
Seek
Command code (in hex)
F2
H
H
H
70
91
Set Drive Parameters
Set Features
EF
H
Set Max Address
Note: Individual Set Max com-
F9
H
Address
00
01
02
03
H
H
H
H
H
mands are identified by the value Password
placed in the Set Max Features
register as defined to the right.
Lock
Unlock
Freeze Lock 04
Set Multiple Mode
Sleep
C6
H
99 E6
H,
H
S.M.A.R.T.
B0
H
Standby
96 E2
H, H
Standby Immediate
Vendor Unique
Write Buffer
94 E0
H, H
9A FA FB
H,
H
H,
H
E8
Write DMA
CA CB
H, H
Write DMA Extended
Write Log Extended
Write Multiple
35
32
H
H
C5
H
Write Multiple Extended
Write Sectors
39
H
30 31
H,
H
Write Sectors Extended
34
H
ATA-standard power-management commands
Check Power Mode
Idle
98 or E5
H
H
H
H
H
H
H
97 or E3
H
Idle Immediate
95 or E1
H
Sleep
99 or E6
H
Standby
96 or E2
H
Standby Immediate
ATA-standard security commands
Security Set Password
Security Unlock
Security Erase Prepare
Security Erase Unit
94 or E0
H
F1
F2
F3
F4
H
H
H
H
Momentus 5400.2 Blade Server Product Manual, Rev. B
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.2
Identify Device command
The Identify Device command (command code EC ) transfers information about the drive to the host following
H
power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 on
page 22. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or
Thefollowingcommandscontaindrive-specificfeaturesthatmaynotbeincludedintheDraftATA-6Standard.
Word
Description
Value
0C5A
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
H
1
Number of logical cylinders
16,383
2
ATA-reserved
0000
16
H
3
Number of logical heads
4
Retired
0000
H
H
5
Retired
0000
6
Number of logical sectors per logical track: 63
Retired
003F
H
7–9
10–19
20
0000
H
Serial number: (20 ASCII characters, 0000 = none)
ASCII
H
Retired
Retired
Obsolete
0000
0400
0000
x.xx
H
H
H
21
22
23–26
Firmware revision
(8 ASCII character string, padded with blanks to end of string)
27–46
47
Drive model number (40 ASCII characters, padded with blanks
to end of string)
ST9120821AB
ST9100824AB
ST98823AB
ST96812AB
ST94813AB
(Bits 7–0) Maximum sectors per interrupt on Read multiple and
Write multiple (16)
8010
H
48
Reserved
0000
H
49
Standard Standby timer, IORDY supported and may be disabled
ATA-reserved
2F00
H
H
H
H
H
50
0000
0200
0200
0007
51
PIO data-transfer cycle timing mode
Retired
52
53
Words 54–58, 64–70 and 88 are valid
Number of current logical cylinders
Number of current logical heads
Number of current logical sectors per logical track
Current capacity in sectors
54
xxxx
xxxx
xxxx
xxxx
H
55
H
H
H
56
57–58
Momentus 5400.2 Blade Server Product Manual, Rev. B
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Word
Description
Value
xxxx
59
Number of sectors transferred during a Read Multiple or Write
Multiple command
H
60–61
Total number of user-addressable LBA sectors available
ST9120821AB = 234,441,648
ST9100824AB = 195,371,568
ST98823AB = 156,301,488
ST96812AB = 117,210,240
ST94813AB = 78,140,160
62
63
Retired
0000
H
H
Multiword DMA active and modes supported (see note following
this table)
xx07
64
65
Advanced PIO modes supported (modes 3 and 4 supported)
0003
0078
H
Minimum multiword DMA transfer cycle time per word (120
nsec)
H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078
H
67
Minimum PIO cycle time without IORDY flow control (240 nsec)
Minimum PIO cycle time with IORDY flow control (120 nsec)
ATA-reserved
00F0
H
H
H
H
H
68
0078
0000
0000
0000
69–74
75
Queue depth
76–79
80
ATA-reserved
Major version number
007E
H
H
81
Minor version number
0000
82
Command sets supported
346B
H
83
Command sets supported
7D01
H
84
Command sets support extension
Command sets enabled
4003
H
85
34xx
H
H
86
Command sets enabled
3xxx
87
Command sets enable extension
4003
H
88
Ultra DMA support and current mode
(see note following this table)
xx3F
H
89
Security erase time
0000
0000
0040
H
H
H
90
Enhanced security erase time
Advanced power management value
Master password revision code
Hardware reset value (see description following this table)
Auto acoustic management setting
ATA-reserved
91
92
FFFE
H
93
xxxx
xxxx
H
94
H
95–127
128
129–159
0000
0001
H
Security status
H
Seagate-reserved
xxxx
H
26
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Word
160–254
255
Description
ATA-reserved
Integrity word
Value
0000
xxA5
H
H
Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data.
Description (if bit is set to 1)
Bit
0
Word 63
Multiword DMA mode 0 is supported.
Multiword DMA mode 1 is supported.
Multiword DMA mode 2 is supported.
Multiword DMA mode 0 is currently active.
Multiword DMA mode 1 is currently active.
Multiword DMA mode 2 is currently active.
1
2
8
9
10
Bit
0
Word 88
Ultra DMA mode 0 is supported.
Ultra DMA mode 1 is supported.
Ultra DMA mode 2 is supported.
Ultra DMA mode 3 is supported.
Ultra DMA mode 4 is supported.
Ultra DMA mode 0 is currently active.
Ultra DMA mode 1 is currently active.
Ultra DMA mode 2 is currently active.
Ultra DMA mode 3 is currently active.
Ultra DMA mode 4 is currently active.
Ultra DMA mode 5 is currently active.
1
2
3
4
8
9
10
11
12
13
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
Momentus 5400.2 Blade Server Product Manual, Rev. B
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.3
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-
rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
Table 7:
Features register values
02
03
Enable write cache (default).
H
Set transfer mode (based on value in Sector Count register).
H
Sector Count register values:
00
01
08
09
Set PIO mode to default (PIO mode 2).
Set PIO mode to default and disable IORDY (PIO mode 2).
PIO mode 0
H
H
H
H
PIO mode 1
0A
PIO mode 2
H
0B
PIO mode 3
H
0C
PIO mode 4 (default)
Multiword DMA mode 0
Multiword DMA mode 1
Multiword DMA mode 2
Ultra DMA mode 0
H
20
21
22
40
41
42
43
44
45
H
H
H
H
H
H
H
H
H
Ultra DMA mode 1
Ultra DMA mode 2
Ultra DMA mode 3
Ultra DMA mode 4
Ultra DMA mode 5
05
55
82
Enable advanced power management
Disable read look-ahead (read cache) feature.
Disable write cache.
H
H
H
AA
Enable read look-ahead (read cache) feature (default).
Report full capacity available
H
F1
H
Note. At power-on or after a hardware or software reset the default values of the features are as indicated
above.
28
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0
Seagate Technology support services
Online services
Internet
www.seagate.com for information about Seagate products and services. Worldwide support is available 24
hours daily by e-mail for your questions.
mySeagate
my.seagate.com is the industry’s first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to man-
age their Seagate account functions. Submit pricing requests, orders and returns through a single, password-
protected Web interface—anytime, anywhere in the world.
reseller.seagate.com
reseller.seagate.com supports Seagate resellers with product information, program benefits and sales tools.
You may register for customized communications that are not available on the web. These communications
contain product launch, EOL, pricing, promotions and other channel-related information. To learn more about
the benefits or to register, go to reseller.seagate.com, any time, from anywhere in the world.
Automated phone services
®
SeaFONE (1-800-SEAGATE) is the Seagate toll-free number (1-800-732-4283) to access our automated
directory assistance for Seagate Service Center support options. International callers can reach this service by
dialing +1-405-324-4770.
Seagate Service Centers
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as drive availability and compatibility.
Technical Support
If you need help installing your drive, consult your system's documentation or contact the dealer's support ser-
vices department for assistance specific to your system. Seagate technical support is also available to assist
you online at support.seagate.com or through one of our call centers. Have your system configuration informa-
tion and your drive’s “ST” model number available.
SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or
comments 24 hours daily and exchange messages with a technical support specialist during normal business
hours for the call center in your region.
Momentus 5400.2 Blade Server Product Manual, Rev. B
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-
related issues. Resellers or end users of drive products should contact their place of purchase or one of the
Seagate CSO warranty centers for assistance. Have your drive’s “ST” model number and serial number avail-
able.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our Data Recovery Ser-
vices labs are currently located in North America. To get a free quick quote or speak with a case management
representative, call 1-800-475-0143. Additional information, including an online request form and data loss pre-
Authorized Service Centers
In some locations outside the US, you can contact an Authorized Service Center for service.
USA/Canada/Latin America support services
Seagate Service Centers
Presales Support
Call center
Toll-free
Direct dial
FAX
+1-405-324-4704
Americas
1-877-271-32851
+1-405-324-47301
Technical Support
Call center
Americas
Toll-free
Direct dial
FAX
+1-405-324-3339
1-800-SEAGATE2
+1-405-324-47002
Customer Service Operations
Warranty Service
Call center
Toll-free
Direct dial
—
FAX / E-mail
+1-956-664-4725
USA, Canada, Mexico and
Latin America
1-800-468-34723
Brazil
Jabil Industrial Do Brasil
—
+55-11-4191-4761
+55-11-4191-5084
LTDA4
Data Recovery Services
Call center
Toll-free
Direct dial
FAX
USA, Canada,
and Mexico
1-800-475-01435
+1-905-474-2162
1-800-475-0158
+1-905-474-2459
1
Hours of operation are 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 6:00 P.M., Monday through Friday (Central time).
Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday (Central time).
Hours of operation are 8:00 A.M. to 5:00 P.M., Monday through Friday (Central time).
Authorized Service Center
2
3
4
5
Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday, and 9:00 A.M. to 5:00 P.M., Saturday (Eastern time).
30
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
European support services
For presales and technical support in Europe, dial the Seagate Service Center toll-free number for your spe-
cific location. If your location is not listed here, dial our presales and technical support call center at +1-405-
324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Monday through Friday.
The presales and technical support call center is located in Oklahoma City, USA.
For European warranty service, dial the toll-free number for your specific location. If your location is not listed
here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A.M. to 5:00 P.M. (Central Europe
time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands.
Seagate Service Centers
Toll-free support numbers
Call center
Austria
Belgium
Denmark
France
Germany
Ireland
Italy
Presales and Technical Support
—
Warranty Service
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-47324289
00 800-311 12 38
00 800-47324289
00 800-47324289
00 800-47324289
00 800-31 92 91 40
00 800-47324289
00 800-47324283 (00 800-4SEAGATE)
00 800-47324283
00 800-47324283
00 800-47324283
00 800-47324283
00 800-47324283
00 800-47324283
00 800-47324283
00 800-311 12 38
00 800-47324283
00 800-47324283
00 800-47324283
00 800-31 92 91 40
00 800-47324283
Netherlands
Norway
Poland
Spain
Sweden
Switzerland
Turkey
United Kingdom
FAX services—All Europe (toll call)
Technical Support
Warranty Service
+1-405-324-3339
+31-20-653-3513
Africa/Middle East support services
For presales and technical support in Africa and the Middle East, dial our presales and technical support call
center at +1-405-324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Mon-
day through Friday. The presales and technical support call center is located in Oklahoma City, USA.
For warranty service in Africa and the Middle East, dial our European CSO warranty center at +31-20-316-
7222 from 8:30 A.M. to 5:00 P.M. (Central Europe time) Monday through Friday, or send a FAX to +31-20-653-
3513. The CSO warranty center is located in Amsterdam, The Netherlands.
Momentus 5400.2 Blade Server Product Manual, Rev. B
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Asia/Pacific support services
For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/
Pacific toll-free numbers are available from 6:00 A.M. to 10:45 A.M. and 12:00 P.M. to 6:00 P.M. (Australian East-
ern time) Monday through Friday, except as noted. If your location is not listed here, direct dial one of our tech-
nical support locations.
Warranty service is available from 9:00 A.M. to 6:00 P.M. April through October, and 10:00 A.M. to 7:00 P.M.
November through March (Australian Eastern time) Monday through Friday.
Seagate Service Centers
Call center
Australia
China (Mandarin)
Hong Kong
Toll-free
1800-14-7201
800-810-9668
800-90-0474
Direct dial
—
+86-10-6225-5336
FAX
—
—
—
—
—
—
—
1, 4
—
—
—
—
—
—
—
—
—
—
—
1, 4
Hong Kong (Cantonese)
001-800-0830-1730
1-600-180-1104
001-803-1-003-2165
0034 800 400 554
007 98 8521 7635
1-800-80-2335
0800-443988
800-1101-150
00-800-0830-1730
001-800-11-0032165
2, 4
India
Indonesia
3, 4
Japan
Korea
3, 4
—
—
—
Malaysia
New Zealand
Singapore
Taiwan (Mandarin)
Thailand
+65-6488-7525
—
—
1, 4
Customer Service Operations
Warranty Service
Call center
Asia/Pacific
Australia
Toll-free
—
1800-12-9277
—
Direct dial
+65-6485-3595
—
FAX
+65-6485-4860
—
4
India
+91-44-821-6164
+91-44-827-2461
1
Hours of operation are 8:30 A.M. to 5:30 P.M., Monday through Friday (Australian Western time).
Hours of operation are 9:00 A.M. to 6:00 P.M., Monday through Saturday.
Hours of operation are 9:30 A.M. to 6:30 P.M., Monday through Friday.
Authorized Service Center
2
3
4
32
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Publication feedback survey
We are interested in your comments and suggestions regarding this publication. Please take a few minutes to
participate in our survey at the following URL:
Thank you for your time and comments.
Momentus 5400.2 Blade Server Product Manual, Rev. B
33
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
discs 5
dissipation 8
Index
Numerics
A
acoustics 12
AFR 13
E
enclosures 14
errors 13
altitude 10
autodetection 1
European Union Restriction of Hazardous Substanc-
es 15
B
BPI 6
burst 1
F
frequency 12
C
certification 13
commands 22
G
compliance 13
H
CSEL 18
handling 17
height 6
humidity 10
C-Tick 14
cycles 13
I
D
density 6
IEC950 13
Momentus 5400.2 Blade Server Product Manual, Rev. B
35
Download from Www.Somanuals.com. All Manuals Search And Download.
interference 14
interleave 6
R
J
K
L
length 6
Load/Unload 13
register 28
reliability 13
resistance 9
M
master/slave 1
modes 21
monitoring 1
RF 12
RoHS 15
N
noise 9
S
S.M.A.R.T. 23
screws 19
O
SeaTools 1
sectors 5
Seek 23
Seeking 8
P
pins 21
PIO 21
precautions 19
36
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Momentus 5400.2 Blade Server Product Manual, Rev. B
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100367617, Rev. B, Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|