INSTRUCTION MANUAL
DVC-2600
English
DVD Player + Video Cassette Recorder
Lecteur DVD + Magnétoscope à cassette
Français
Only cassettes marked
can be used with this video cassette recorder.
As an ENERGY STAR® Partner,
SANYO has determined that
this product or product model
meets the ENERGY STAR®
guidelines for energy efficiency.
Please read this manual carefully before connecting your DVD+VCR and operating it for the first time.
Keep the manual in a safe place for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following proce-
dures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and oper-
ating instructions should be read before the product is
operated.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future refer-
ence.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. -
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The open-
ings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This prod-
uct should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is pro-
vided or the manufacturer’s instructions have been
adhered to.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radi-
ators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Operation with DVD . . . . . . . . . . . . . . . . . . . . . 27-29
Playing DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
General Features. . . . . . . . . . . . . . . . . . . . . . . . 27
ꢀ Moving to another TITLE . . . . . . . . . . . . . . . 27
ꢀ Moving to another CHAPTER. . . . . . . . . . . . 27
ꢀ Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 27
ꢀ Still Picture and Frame-by-Frame Playback . 28
ꢀ Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ Random. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ Time Search . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 28
ꢀ Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ Marker Search . . . . . . . . . . . . . . . . . . . . . . . 29
Special DVD Features . . . . . . . . . . . . . . . . . . . . 29
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
Connecting Antenna/Cable TV to DVD+VCR . . . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional, Preferred TV Connections . . . . . . . 12-13
Before Operation - VCR Part . . . . . . . . . . . . . . 14-16
On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 14
Setting the On-Screen Display . . . . . . . . . . . . . . 14
Setting the VCR Setup Menu . . . . . . . . . . . . . . . 15
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 16
Before Operation - DVD Part . . . . . . . . . . . . . . 17-20
General Explanation. . . . . . . . . . . . . . . . . . . . . . 17
On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . 17
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 18-20
ꢀ General Operation . . . . . . . . . . . . . . . . . . . . 18
ꢀ Language . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ꢀ Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ꢀ Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ꢀ Parental Control. . . . . . . . . . . . . . . . . . . . . . 20
ꢀ
Checking the contents of DVD Video discs: Menus . 29
ꢀ Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 29
ꢀ Changing the Audio Language . . . . . . . . . . . 29
ꢀ Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Operation with Audio CD and MP3 Discs. . . . . . . 30
Playing an Audio CD and MP3 Discs . . . . . . . . . 30
ꢀ Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ꢀ Moving to another Track . . . . . . . . . . . . . . . 30
ꢀ Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 30
ꢀ Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ꢀ Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ꢀ Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 30
ꢀ 3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 30
ꢀ Changing the Audio Channel . . . . . . . . . . . . 30
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 31
Programmed Playback with Audio CD
and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 31
ꢀ Repeat Programmed Tracks . . . . . . . . . . . . 31
ꢀ Erasing a Track from Program List. . . . . . . . 31
ꢀ Erasing the Complete Program List . . . . . . . 31
ꢀ To resume normal playback from
Operation
Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-26
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 21
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 21
ꢀ Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Still Picture and Frame-by-Frame Playback . 21
ꢀ Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 21
ꢀ Ad JUMP (Advertisement Jump). . . . . . . . . . 21
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 22
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 22-23
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 24
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 24
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 24
VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 25
Tape Counter Memory Feature. . . . . . . . . . . . . . 26
Additional Information . . . . . . . . . . . . . . . . . . . . 26
programmed playback . . . . . . . . . . . . . . . . 31
Additional Information - DVD Part . . . . . . . . . . . . 32
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 32
Notes on MP3 Discs . . . . . . . . . . . . . . . . . . . . . 32
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 33-34
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 35
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use
Disc-related terms
Title (DVD only)
Playable Discs
The main film content or accompanying feature content
or music album.
DVD
(8 cm/12 cm disc)
Each title is assigned a title reference number enabling
you to locate it easily.
Audio CD
(8 cm/12 cm disc)
Chapter (DVD only)
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chap-
ters. Each chapter is assigned a chapter number to
enable you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Notes
– Depending on the conditions of the recording equip-
ment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
– The unit cannot play discs that contain data other
than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal). It may result in malfunctions.
Track (audio CD only)
Sections of a musical piece on an audio CD. Each track
is assigned a track number, enabling you to locate the
track you want.
Remote control battery installation
Detach the battery cover on the rear of the
remote control, and insert two R03 (size
Notes on DVDs
AAA) batteries with
correctly.
and
aligned
Some playback operations of DVDs may be intention
ally fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the soft-
ware manufacturer, some playback features of the unit
may not be available or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
played on the unit.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
ꢀ Distance: About 23 ft (7 m) from the front of the
remote sensor
ꢀ Angle: About 30° in each direction of the front of the
remote sensor
Regional code of the DVD+VCR and DVDs
This DVD+VCR is designed and manufactured
1
for playback of region 1 encoded DVD software.
The region code on the labels of some DVD discs indi-
cates which type of DVD+VCR can play those discs. This
unit can play only DVD discs labeled 1 or ALL. If you try
to play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their play-
back is prohibited by area limits.
IMPORTANT NOTE:
SPENT OR DISCHARGED BATTERIES MUST BE
RECYCLED OR DISPOSED OF IN A SAFE MANNER
IN COMPLIANCE WITH ALL APPLICABLE LAWS.
FOR DETAILED INFORMATION, CONTACT YOUR
LOCAL COUNTY SOLID WASTE AUTHORITY.
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the vol-
ume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 chan-
nel Digital SurroundTM decoder system must be con-
nected to the digital output of the unit.
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. Copyright
1992-1997 Dolby Laboratories. All rights reserved.
DTS and DTS Digital Out are trademarks of Digital Theater
Systems, Inc.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use (Continued)
Precautions
Cleaning discs
Fingerprints and dust on the disc can cause poor pic-
ture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the cen-
ter out.
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
Yes
No
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
About Symbols
Cleaning the unit
About the
symbol display
To clean the cabinet
“
” may appear on the TV screen during operation.
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
To obtain a clear picture
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
DVD DVD
CD
Audio CDs.
MP3 MP3 Discs.
Setting the Output Source
For details, please contact your nearest dealer.
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
Notes on Discs
• If you want to view output source of DVD deck:
Press DVD on the remote or DVD/VCR on the front panel
until DVD indicator in the display window lights and output
source of DVD deck is viewed on the TV screen.
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
• If you want to view output source of VCR deck:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator in the display window lights and output
source of VCR deck is viewed on the TV screen.
Do not stick paper or tape on the disc.
Note
• If you insert a disc when the DVD+VCR is in the VCR
mode, the DVD+VCR will be set to DVD mode
automatically.
Storing discs
• If you insert a cassette tape without prevention tab
when the DVD+VCR is in the DVD mode, the
DVD+VCR will be set to VCR mode automatically.
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sun-
light, as there may be a considerable temperature
increase inside the car.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
Disc Tray (DVD deck)
Insert a disc here.
EJECT(Z)
Ejects the tape in the VCR deck.
CHANNEL (v/V)
To scan up or down through memorized channels.
Cassette Compartment (VCR deck)
Insert a video cassette here.
Remote Sensor
Point the DVD+VCR remote control here.
Display window
Shows the current status of the DVD+VCR.
OPEN/CLOSE (Z)
Opens or closes the disc tray.
PLAY (B)
Starts playback of a tape in
the VCR deck.
DVD/VCR indicator
Indicates the active deck.
STOP (x)
Stops playback of disc.
x
)
STOP (
Stops playback of tape.
REC (z)
To record normally or to activate
PLAY (B)
Starts playback of a disc
in the DVD deck.
Instant Timer Recording.
AV INPUT (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an
external source (Audio system,
TV/Monitor, Another VCR).
PAUSE/STILL(X)
Pause playback of a disc in the DVD
deck temporarily/press repeatedly
for frame-by-frame playback.
DVD/VCR (output select)
Child Lock
The control buttons on the front panel of the DVD+VCR
can be switched off so that your DVD+VCR can only be
operated using the remote control.
Select one of your output sources to
view on the TV screen between DVD
and VCR.
POWER
Switches the DVD+VCR ON and OFF.
Press SAFE on the remote control to enable LOCK func-
tion,
appears in the display window.
SAFE
To disable the LOCK function, press SAFE on the remote
control until appears in the display window.
OFF
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Window
The DVD deck is selected.
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
Indicates repeat mode.
DVD to VCR copy is in progress.
DVD+VCR is in timer recording or a timer
recording is programmed.(VCR part only)
A cassette is in the VCR deck.
The VCR deck is selected.
DVD
COPY
VCR
REC
PM
TV
DVD+VCR functions are available and
channels are selected at TV.
Indicates PM time. (AM is not displayed.)
DVD+VCR is Recording.
(VCR part only)
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
DVD/VCR select button
Select the output source (DVD or VCR)
to view on the TV screen.
OPEN/CLOSE, EJECT (Z)
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
POWER
SELECT/ENTER
- Acknowledges menu selection.
- Displays functions on the TV screen.
Switches DVD+VCR ON and OFF.
TV/VCR
To view channels selected by the VCR
tuner or by the TV tuner.
This button is not available.
DISC MENU
Accesses menu on a DVD disc.
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
INPUT
To select the VCR deck’s source (Tuner,
LINE 1, or LINE 2).
b/B/v/V (left/right/up/down)
ꢀ FORWARD (>)
- Selects an option in the menu
DVD; Search forward*/go to next chap-
ter or track.
-
CH/TRK (v/V): Selects channel of VCR.
Adjusts manually the tape’s picture
onscreen.
VCR; Advances the tape during the
STOP mode or for fast forward picture
search.
SETUP, MENU
Accesses or removes DVD setup menu
and VCR menu.
ꢀ PLAY (H)
Starts playback.
TITLE ꢀ
Displays the disc’s Title menu, if
available.
ꢀ BACKWARD (.)
DVD; Search backward*/go to beginning
of current chapter or track or go to previ-
ous chapter or track.
PAUSE/STEP (X) ꢀ
Pause playback or recording
temporarily/press repeatedly for frame-
by-frame playback.
VCR; Rewinds the tape during the
STOP mode or for fast reverse picture
search.
* Press and hold button for about two
seconds.
STOP (x) ꢀ
Stops playback.
PROGRAM
REC (z) ꢀ
Records normally or activates Instant
Timer Recording.
Accesses or removes Program menu.
CLEAR
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
0-9 numerical buttons
Selects numbered options in a menu.
AUDIO ꢀ
Selects an audio language (DVD) or an
audio channel (CD).
ꢀ SAFE
Switch the Lock function on and off.
ꢀ ANGLE
SUBTITLE ꢀ
Selects a DVD camera angle if
available.
Selects a subtitle language.
MARKER ꢀ
Marks any point during playback.
ꢀ RETURN
Removes the setup menu.
SEARCH ꢀ
Displays MARKER SEARCH menu.
ꢀ ZOOM
Enlarges DVD video image.
REPEAT ꢀ
Repeat chapter, track, title, all.
RANDOM, Ad JUMP ꢀ
- Plays tracks in random order.
- Fast forwards picture search through
30 seconds of recording.
Note
This remote control use the same buttons for VCR and DVD
functions (ex. PLAY).
A-B, SP/SLP ꢀ
- Repeats sequence.
When using a VCR, first press the VCR button.
When using a DVD, first press the DVD button.
- Selects recording speed
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
COMPONENT VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with video and audio inputs.
Connect to a TV with Y Pb Pr inputs.
AUDIO OUT (Left/Right) (DVD OUT)
Connect to a TV, amplifier, receiver, or stereo system.
VHS IN LINE 1
(VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external
source (Audio system, TV/Monitor,
Another VCR).
DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)
Connect to digital (coaxial) audio equipment.
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
AC Power Cord
Plug into the power source.
Video Output Select Switch
Select either S-VIDEO OUT or COMPONENT
VIDEO OUT, depending on how you connected the
DVD+VCR to the TV.
RF OUT(DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
ANTENNA INPUT
Connect the VHF/UHF/CATV antenna to this terminal.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Without Cable Box
Tips
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD+VCR. Use the supplied round
coaxial cable to connect between the DVD+VCR’s RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this
connection, you can receive all midband, super band, and
hyperband channels.
ꢀ
ꢀ
ꢀ
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD+VCR. Use connections described on pages 11-13.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
For better sound reproduction, connect the DVD+VCR’s
DVD/VCR AUDIO OUT jack to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment. See
Optional, Preferred TV Connections on pages 12-13.
With Cable Box
If a converter is required in your cable system, follow the
instruction below:
The cable hookup permits both TV and DVD+VCR operation.
Caution
To view or record CATV channel
ꢀ
ꢀ
Make sure the DVD+VCR is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT
jack to the phono in jack (record deck) of your audio
system.
1 Tune the TV to the DVD+VCR output channel (CH 3 or 4).
2 Set the DVD+VCR channel selector to the output channel of
the Cable Converter box by pressing the CH/TRK (v/V) or
number (0-9) of your DVD+VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
ꢀ
Do not connect your DVD+VCR via your VCR. The DVD
image could be distorted by the copy protection system.
Notes
ꢀ With this connection, you CANNOT record one program
while viewing another.
ꢀ If you are using a cable box to tune channels, it is not nec-
essary to do Auto Channel Programming as indicated on
page 15.
Connecting Antenna/Cable TV to
DVD+VCR
Disconnect the antenna leads from the rear of the
1
TV.
Cable TV
Wall Jack
Identify the type of cable from your antenna. If it is
2 a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
the jack marked ANT.IN on your DVD+VCR.
Back Panel of
Typical Cable Box
Tip
If your antenna lead wire is a flat type antenna cable,
connect it to a Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD+VCR,
it just slips over the jack.
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
Rear of DVD+VCR
300/75 ohm
Adaptor
(Not supplied)
OR
OR
Rear of DVD+VCR
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (Continued)
Basic TV Connections
Optional, Preferred TV Connections
ꢀ
Make one of the following connections, depending on
the capabilities of your existing equipment.
Notes
ꢀ You can ONLY watch and listen to DVD playback
through the connections shown below.
RF coaxial connection
ꢀ
When using the COMPONENT VIDEO OUT jacks,
set the video output select switch to COMPO-
NENT. When using the S-VIDEO OUT jack, set the
video output select switch to S-VIDEO.
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note
S-Video connection
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
Connect the S-VIDEO OUT jack on the DVD+VCR
1
to the S-Video in jack on the TV using the optional
S-Video cable (S).
How to set the DVD+VCR’s RF output channel
1.When the DVD+VCR is turned off, press and hold
CHANNEL (v/V) on the front panel for about five
seconds.
It will turn itself on and “RF 03” or “RF 04” appears in the
display window.
2.Press CHANNEL (v/V) on the front panel or CH/TRK
(v/V) on the remote control to change the RF output
channel (CH 03 or CH 04).
Connect the Left and Right AUDIO OUT jacks of
2 the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
®
Component Video (Color Stream ) connection
Connect the COMPONENT VIDEO OUT jacks on
1
the DVD+VCR to the corresponding in jacks on the
TV using an optional Y Pb Pr cable (C).
3.Turn off and on the DVD+VCR.
Connect the Left and Right AUDIO OUT jacks of
2 the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Audio/Video connection
Connect the DVD/VCR VIDEO OUT jack on the
1
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
Rear of TV
Connect the Left and Right DVD/VCR AUDIO OUT
2 jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
S-VIDEO
INPUT
COMPONENT VIDEO INPUT
AUDIO INPUT
Y
Pr
Pb
R
L
Note
If you use this connection, set the TV’s source selector
to VIDEO.
Rear of TV
S
C
A2
ANTENNA
INPUT
VIDEO
INPUT
AUDIO INPUT
R
L
R
A1
V
Rear of DVD+VCR
Rear of DVD+VCR
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (Continued)
Rear of DVD+VCR
Optional, Preferred TV Connections
Note
You can ONLY listen to DVD playback using COAXIAL
(X) and AUDIO OUT (A2) connections. The tuner and
VCR will still be heard through the RF.OUT (R) or
DVD/VCR AUDIO OUT (A1) jack. (See page 12.)
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
Connect the Left and Right AUDIO OUT (or DVD/VCR
AUDIO OUT) jacks on the DVD+VCR to the audio left
and right in jacks on your amplifier, receiver, or stereo
system using the audio cables (A1, A2) supplied.
A1
A2
X
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/Video
receiver equipped with a multi-channel decoder
(Dolby Digital™, MPEG 2, or DTS)
R
L
COAXIAL
DIGITAL INPUT
AUDIO INPUT
Amplifier (Receiver)
Connect one of the DVD+VCR’s DIGITAL AUDIO
1
OUT jacks (COAXIAL X) to the corresponding in
jack on your amplifier. Use an optional digital
(coaxial X) audio cable.
Accessory Audio/Video (A/V) Connections to
DVD+VCR
Connect the VHS IN LINE 1 or AV INPUT jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using the optional audio/video
cables.
You will need to activate the DVD+VCR’s digital
2 output. (See Digital Audio Output on page 19).
Digital Multi-channel sound
Accessory Component:
VCR, Camcorder,
Video Camera,
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD+VCR (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Satellite Receiver,
Laser Disc Player
Jack panel of Accessory
AUDIO
OUTPUT
R
L
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
VIDEO
OUTPUT
Notes
–
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital con-
nection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
– To see the audio format of the current DVD in the on-
screen display, press AUDIO.
OR
Rear of DVD+VCR
Front of DVD+VCR
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - VCR Part
On-Screen Display (OSD)
Some of these functions will be displayed every time the
VCR is operated.
EASY INFORMATION
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during play-
back of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title and program
details are shown in the TV screen.
❶
❷
❸
❹
❺
When viewing a channel with Extended Data Service (XDS)
signals, press SELECT/ENTER then the station ID will
appear on the TV screen. Press SELECT/ENTER again
and the program details will appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press SELECT/ENTER twice
then the program title and program details will appear
on the TV screen.
PLAY
SP
HI-FI
CH 4
STEREO
JUL 5 , SAT
2:15 PM
❻
❼
PROGRAM DETAILS
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
❶ TAPE SPEED DISPLAY
Shows the current tape speed.
❷ FUNCTION DISPLAY
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
Indicates the function in progress.
❸ HI-FI DISPLAY
Indicates when this unit is playing back tape recorded with
Hi-Fi.
❹ CHANNEL DISPLAY
CH 4
WABC STEREO
PROGRAM DETAILS
“Home video”
SP
Indicates the selected channel (or LINE1, LINE2).
❺ STEREO/SAP DISPLAY (MONO is not displayed)
Shows the type of audio signal received by the VCR tuner.
❻ DATE DISPLAY
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
“Home video”
JUL 5 , SAT
2:15 PM
Shows the current date. (Month/Date/Day of the week
format)
Easy Information Screen
(Program details)
Easy Information Screen
(Station ID)
❼ CLOCK/COUNT/REMAIN DISPLAY
Shows the current time, the tape counter and remaining time
Setting the On-Screen Display
on the tape.
The SETUP, clock setting, and timer recordings are
accessed conveniently with On-Screen Menu Displays
that lead you through each step. The following pages
describe the On-screen selections to be set.
Each press of the SELECT/ENTER changes the TV
screen in the following sequence.
STOP
SP
CH
STEREO
4
Menu Selection
Your VCR allows remote control adjustment of several
JUL 5 , SAT
2:15 PM
features.
2:15 PM
Press MENU and the MAIN menu will appear.
0:35:40
1
REM 1:58
Select the desired menu with v/V button and
2 then press SELECT/ENTER.
Note
Notes
Menus remain on-screen for 3 minutes.
ꢀ The function displays can be seen displayed on the TV
screen for 5 seconds.
MAIN MENU
ꢀ The clock (or tape counter, tape remaining) mode will contin-
ue until you press SELECT/ENTER.
ꢀ The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
CLOCK SET (page 16)
PROGRAM (page 22)
TUNING (page 15)
SETUP (page 15)
Press MENU when finished.
3
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - VCR Part (Continued)
Setting the VCR Setup Menu
Channel Selection
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Press MENU and the MAIN menu will appear.
1
Press v/V to select the SETUP menu, then
2 press SELECT/ENTER.
Preparation:
The SETUP menu will appear.
ꢀ Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
Press MENU and the MAIN menu will appear.
1
Press v/V to choose a desired option on the
3 SETUP menu. Then press b/B to choose a
desired setting.
Press v/V to select the TUNING menu, then
2 press SELECT/ENTER.
The TUNING menu will appear.
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or off.
ꢀ FUNCTION OSD can be switched between ON and OFF by
pressing b/B.
LANGUAGE SELECT
The on-screen programming of this DVD+VCR can be
displayed in either English, Spanish, or French.
ꢀ LANGUAGE SELECT can be switched among ENGLISH,
SPANISH and FRENCH by pressing b/B.
Press V to choose the SOURCE SELECT option,
AUDIO MODE
3 then press b/B to select TUNER.
The DVD+VCR has two separate audio playback systems, the
high quality VHS Hi-Fi system and standard NORMAL mono
system. The same audio is generally recorded on both
systems. The VHS Hi-Fi system plays on separate (left and
right) channels, and the NORMAL system plays monaural
sound. The normal track is always played so the cassette can
be played on a DVD+VCR that does not have VHS Hi-Fi.
ꢀ AUDIO MODE can be switched between HI-FI and
NORMAL by pressing b/B.
Press b/B repeatedly to switch among TUNER, LINE1
and LINE2.
Press v/V to choose the AUTO CHANNEL SET
4 option, then press b/B to set the channel.
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
After the AUTO CHANNEL SET PROCEEDING is
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding receiving
mode (Stereo or SAP) regardless of the selected position. For
normal operation, the display should be in the STEREO position.
The DVD+VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the dis-
play to mono may give clearer sound.
5 complete, make sure the TUNING BAND is set
appropriately (TV or CATV) by pressing v/V and
choosing the correct TUNING BAND (TV or
CATV) by pressing b/B using the TUNING
menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
Press MENU to return to the TV screen.
6
ꢀ BROADCAST TYPE can be switched among STEREO, SAP,
and MONO by pressing b/B.
Use CH/TRK (v/V) or CHANNEL (v/V) on the
front panel to cycle the DVD+VCR through the
channels in memory.
7
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo posi-
tion, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
ꢀ AUDIO OUTPUT can be switched among STEREO, LEFT,
and RIGHT by pressing b/B.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
1
Press V to choose the CH. ADD/DEL option on the
TUNING menu. Press b/B to select a channel to
add or erase.
2
3
Press SELECT/ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
Press MENU when finished.
4
Press MENU to return to the TV screen.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - VCR Part (Continued)
Setting the Clock
Note
There are cases where the TV station does not send or sends
The DVD+VCR gives you two ways to set the time and
date: the Auto Clock Feature or manually. The Auto
Clock Feature enables the DVD+VCR to set up the clock
when the DVD+VCR is turned off.
wrong date and/or time information and the DVD+VCR sets the
incorrect time.
If this happens we recommend that you set the clock manually.
Manual Clock Set
Things to know before starting
ꢀ
The clock uses the 12-hour system. (Be sure to set AM
Example: JULY 5, 2003 ; 2:15 AM
and PM correctly.)
ꢀ
The initial Clock Setting is JANUARY 1, 2003, 12:00 AM.
Press MENU and the MAIN menu will appear.
1
Auto Clock Set
Press v/V to choose the CLOCK menu.
2 Press SELECT/ENTER and the CLOCK menu
will appear.
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+VCR looks for a channel carrying XDS
(Extended Data Services) information. XDS updates the clock
using the Coordinated Universal Time.
The Auto Clock Feature enables the DVD+VCR to set up
the clock when the DVD+VCR is turned off.
Press MENU and the MAIN menu will appear.
1
Press v/V to choose the CLOCK menu.
2 Press SELECT/ENTER and the CLOCK menu
will appear.
Press b/B to choose the month.
3
Press V to choose the DAY option.
4 Use b/B to choose the day.
The day of the week will display automatically.
Press V to choose the YEAR option.
5 Use b/B to choose the year.
Press V to choose the TIME option.
6 Use b/B to choose the time.
Press V to choose the AUTO CLOCK SET option.
3 Press b/B to choose ON.
Press and hold b/B to advance clock
continuously.
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
Press E to choose the DAYLIGHT SAVINGS
7
item.
Press F or G to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
Press E to choose the DAYLIGHT SAVINGS
4 item.
Press F or G to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
Press E to choose the TIME ZONE item.
5 Press F or G to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
Press MENU when finished.
If “AUTO” is selected as the time zone, the VCR sets the
clock using the first Coordinated Universal Time informa-
tion it finds in a broadcast signal.
8
Press MENU when finished.
Note
6
7
If setting the clock manually, “AUTO CLOCK SET” must
set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+VCR is turned off.
Turn off the DVD+VCR and the auto clock set-
ting works.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD Part
General Explanation
This manual gives the basic instructions for operating
the DVD+VCR. Some DVDs require specific operation
or allow only limited operation during playback. When
Temporary Feedback Field Icons
TITLE
Repeat Title (DVD)
CHAPT
Repeat Chapter (DVD)
A
B
Repeat A-B
this occurs, the symbol
appears on the TV screen,
OFF
Repeat Off
indicating that the operation is not permitted by the
DVD+VCR or is not available on the disc.
Resume play from this point
Action prohibited or not available
On-Screen Display
The general playback status can be displayed on the
TV screen. Some options can be changed on the menu.
Notes
ꢀ Some discs may not provide all of the features on the
on-screen display example shown below.
ꢀ If no button is pressed for 10 seconds, the on-screen
display disappears.
On-screen display operation
Press DISPLAY during playback.
1
Use v/V to select an option.
2 The selected option will be highlighted.
Use b/B to change the setting of an option.
3 The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press SELECT/ENTER to execute the setting.
DVD
Options
Function (Press v
/
V to select desired option)
Selection Method
Title Number
Shows the current title number and total number of
b/B, or
1/3
1/12
titles, and skips to the desired title number.
Numeric, SELECT/ENTER
Chapter Number
Time search
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
b/B, or
Numeric, SELECT/ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numeric, SELECT/ENTER
0:16:57
Audio language
and Digital Audio
Output mode
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
1
ENG
D
5.1CH
b/B, AUDIO
Subtitle language
Shows the current subtitles language, and
OFF
1/1
b/B, SUBTITLE
changes the setting.
Angle
Shows the current angle number and total number of
angles, and changes the angle number.
b/B, ANGLE
Sound
Shows the current sound mode, and
changes the setting.
NORM.
b/B
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD Part (Continued)
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Initial Settings
You can set your own Personal Preferences on the
DVD+VCR.
English
Spanish
French
Disc Audio
Disc Subtitle
Disc Menu
General Operation
Rating
Press SETUP.
The setup menu appears.
Country Code
TV Aspect
1
Menu Language
Digital Audio Output
Original
English
Disc Audio
Disc Subtitle
Disc Menu
French
Rating
German
Spanish
Italian
Others
Country Code
TV Aspect
Menu Language
Digital Audio Output
.pkSt
Chinese
Polish
Picture
Hungarian
Russian
Other — — — —
TV Aspect DVD
Others
4:3 Letterbox: Select when a standard 4:3 TV is con-
nected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a standard 4:3 TV is con-
nected. Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
Use v/V to select the desired option.
2 The screen will show the current setting for the
selected option, as well as alternate setting(s).
While the desired option is selected, press B,
3 then v/V to select the desired setting.
16:9 Wide: Select when a 16:9 wide TV is connected.
Press SELECT/ENTER to confirm your selection.
4 Some options require additional steps.
4:3 Letterbox
Disc Audio
Disc Subtitle
Disc Menu
4:3 Panscan
16:9 Wide
Press SETUP, RETURN, or PLAY (H) to exit the
Rating
5 setup menu.
Language
Country Code
TV Aspect
Menu Language
Digital Audio Output
Disc Language DVD
Select a language for the disc’s Menu, Audio, and
Others
Subtitle.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the lan-
guage code list on page 35. If you enter the wrong language
code, press CLEAR.
Note
Disc Language selection may not work for some DVDs.
Original
English
Disc Audio
Disc Subtitle
Disc Menu
French
Rating
German
Spanish
Italian
Country Code
TV Aspect
Menu Language
Digital Audio Output
5.1 peakeSet
Chinese
Polish
Hungarian
Russian
Other — — — —
Others
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD Part (Continued)
Sound
Others
The DRC and Vocal settings can be changed.
Digital Audio Output
ꢀ
Use v/V to select the desired option and press
SELECT/ENTER. The setting of the selected option
is changed between On and Off.
Each DVD disc has a variety of audio output options.
Set the DVD+VCR’s Digital Audio Output according to
the type of audio system you use.
DOLBY DIGITAL/PCM: Select DOLBY DIGITAL/PCM if
you connected the DVD+VCR’s DIGITAL AUDIO OUT
jack to a Dolby Digital decoder (or an amplifier or other
equipment with a Dolby Digital decoder).
Stream/PCM: Select Stream/PCM if you connected the
DVD+VCR’s DIGITAL AUDIO OUT jack to an amplifier
or other equipment with a DTS decoder, Dolby Digital
decoder or MPEG decoder.
DRC On
Disc Audio
Vocal On
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Digital Audio Output
PCM: Select when connected to a 2 channel digital
stereo amplifier. The DVD+VCR output sounds in the
PCM 2ch format when you play a DVD video disc
recorded with a Dolby Digital, MPEG1, or MPEG2
recording system.
Others
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
DOLBY
DIGITAL /PCM
Disc Audio
Disc Subtitle
Disc Menu
Stream/PCM
PCM
Rating
Country Code
TV Aspect
Sample Freq.
48 KHz
Menu Language
Digital Audio Output
96KHz
Vocal
Others
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
Sample Frequency
To change the Sample Frequency setting, first select
the desired Digital Audio Output as indicated as above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz
signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass each type of signal through
without any further processing.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Operation - DVD Part (Continued)
Parental Control
DVD
Country Code
The Country Code for this DVD+VCR is CANADA.
No user intervention is required.
Rating DVD
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Code Set
Disc Audio
Disc Subtitle
Disc Menu
C
A
Rating
Country Code
TV Aspect
Menu Language
Digital Audio Output
Spr Su
Others
8
Disc Audio
Disc Subtitle
Disc Menu
7
6
Note
Rating
5
Country Code
TV Aspect
Confirmation of the 4-digit password is necessary when
the password is changed (see Changing the 4-digit
password below ).
4
3
Menu Language
Digital Audio Output
2
1
Unlock
Change
Changing the 4-digit password
Others
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old password, then press SELECT/ENTER.
3 Select Change using v/V buttons then press
SELECT/ENTER.
4 Enter the new 4-digit password, then press
SELECT/ENTER.
5 Enter exactly the same password a second time and
verify by pressing SELECT/ENTER.
6 Press SETUP to exit the menu.
Select Rating on the Setup menu using v/V
buttons.
1
2
While Rating is selected, press B.
When you have not entered a password yet.
3 Enter a 4-digit password using the numbered but-
tons to create a personal 4-digit security password,
then press SELECT/ENTER. Enter the 4-digit
password again and press SELECT/ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numerical
buttons to confirm the personal 4-digit security
password, then press SELECT/ENTER.
If you forget your 4-digit password
If you forget your password, to clear the current pass-
word follow the procedure below.
1 Press SETUP to display the setup menu.
2 Enter the 6-digit number 210499 and then press
SELECT/ENTER.
If you make a mistake before pressing SELECT/ENTER,
press CLEAR and enter 4-digit security password again.
The 4-digit password is cleared.
3 Enter a new password as shown above to the left
(Rating).
Select a rating from 1 to 8 using v/V buttons.
4 One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the
DVD+VCR, all disc scenes with the same rating or
lower will be played. Higher rated scenes will not be
played unless an alternative scene is available on
the disc. The alternative must have the same rating
or a lower one. If no suitable alternative is found,
playback will stop. You must enter the 4-digit pass-
word or change the rating level in order to play the
disc.
Press SELECT/ENTER to confirm your rating
5 selection, then press SETUP to exit the menu.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape
Normal Playback
Preparation:
ꢀ Turn on the TV.
Search
This function lets you quickly and visually search for a
desired tape section in either direction: forward and
reverse.
ꢀ Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
1 Press BACKWARD (.) or FORWARD (>)
during playback.
The DVD+VCR will be activated in the SEARCH
ꢀ
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
ꢀ Set the Output Source to VCR as shown in Setting the
Output Source on page 6.
mode.
ꢀ If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
Insert a prerecorded video cassette.
1
2 To return to playback, press PLAY (H).
The
indicator will light and the DVD+VCR will
power-up automatically.
Still Picture and Frame-by-Frame Playback
ꢀ Make sure that the
indicator in the display
1 Press PAUSE/STEP (X) during playback.
Still picture will appear on the TV screen.
ꢀ If a still picture vibrates vertically, stabilize it by pressing
CH/TRK (v/V) on the remote control.
ꢀ If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
window is not lighted. If it is, press POWER once.
ꢀ If a tape without a safety tab is inserted, the unit will
start playback automatically.
Press PLAY (H) once.
2 PLAY appears on the TV screen .
ꢀ It is not necessary to select the tape speed for play-
back. It will be automatically selected by the DVD+VCR.
ꢀ In playback, the TV/VCR selector switches to VCR
mode automatically.
2 Press PAUSE/STEP (X) repeatedly to advance the
video picture one frame at a time while viewing a still
picture.
Press STOP (x) to stop playback.
3 To return to playback, press PLAY (H).
3 STOP appears on the TV screen.
ꢀ If the tape reaches the end before STOP (x) is
pressed, the DVD+VCR will automatically stop, rewind,
eject, and it will turn itself off.
Slow Motion
1 While in still mode, press FORWARD (>).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
ꢀ During slow playback, use CH/TRK (v/V) on the Remote
Control to minimize noise bands.
ꢀ If slow motion mode continues for more than 3 minutes,
the DVD+VCR will automatically change to playback
mode.
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
ꢀ A tape is played back for the first time.
ꢀ Tape speed (SP, LP, SLP) changes.
ꢀ Streaks or snow appear because of scratches on the tape.
2 To return to playback, press PLAY (H).
Ad JUMP (Advertisement Jump)
This is useful for skipping commercials or short program
segments.
Manual Tracking
If noise appears on the screen during playback, press
either CH/TRK (v/V) on the remote control or
CHANNEL (v/V) on the front panel until the noise on
the screen is reduced.
1 Press Ad JUMP during the playback mode.
The tape will fast forward picture search through 30
seconds of recording.
ꢀ The skipping time can be extended by pressing Ad JUMP.
ꢀ In case of vertical jitter, adjust these controls very carefully.
ꢀ Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 sec-
onds.
ꢀ Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 3
minutes).
2 When the search is completed, the DVD+VCR will go
into playback mode automatically.
Special Effect Playbacks
Special effects playback notes
ꢀ Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
ꢀ The audio is automatically muted during special effect modes,
so there is no sound during search.
ꢀ During the high-speed picture search modes, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape(Continued)
Normal Recording
Timer Recording
Preparation:
This DVD+VCR can be programmed to record up to 8
programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
ꢀ Turn on the power of both the DVD+VCR and TV.
ꢀ Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
ꢀ If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
Things to know before starting
ꢀ
If you try to set the program timer before setting the clock,
Insert a video cassette that the safety tab intact.
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
Make sure a tape is in the DVD+VCR and the safety tab is
in place or the tape will be automatically ejected.
1
Select the desired channel by using CH/TRK
2 (v/V).
ꢀ
ꢀ If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2 by pressing INPUT.
Preparation:
ꢀ Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is set to the DVD+VCR output channel (3 or 4).
ꢀ Make sure the TUNING BAND in the TUNING menu is set
appropriately (TV or CATV).
Set the desired recording speed (SP or SLP) by
3 pressing SP/SLP.
ꢀ
ꢀ This DVD+VCR is not designed to record in LP mode.
Set the MTS mode as desired (See page 15, 25).
Press MENU and the MAIN menu will appear.
4
1
2
Press REC (z) once.
Use v/V to choose the PROGRAM menu.
5 Recording will start. (The REC indicator will light in
the display window.)
ꢀ REC indicator appears only when the Output Source is
set to VCR.
Press SELECT/ENTER to go to the PROGRAM
3 menu.
ꢀ If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
The PROGRAM menu will appear.
ꢀ If all programs have already been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
Press STOP (x) to stop recording.
6 If the tape reaches the end before STOP (x) is pressed,
the DVD+VCR will automatically stop, rewind, eject, and it
will turn itself off.
To pause the recording
1 Press PAUSE/STEP (X) to pause the tape during
recording.
The REC indicator will flash in the display window.
Use b/B to choose the PROGRAM No. (1-8).
2 When you want to continue recording, press
4
PAUSE/STEP (X) or press REC (z).
ꢀ After 5 minutes in pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
Use V to choose the MONTH option.
5 Use b/B to choose the desired month.
Use V to choose the DAY option.
To record one TV program while
watching another
1 Press TV/VCR to select the TV mode during record-
ing.
The TV indicator appears.
2 Using the TV, select the channel to be viewed.
6 Use b/B to choose the desired day.
Use V to choose the START option.
7
Use b/B to choose the desired start time.
Use V to choose the STOP option.
8 Use b/B to choose the desired stop time.
Use V to choose the CHANNEL option.
9 Use b/B to choose the desired channel
(Channel, LINE1 or LINE2).
Tips
Always use PAUSE/STEP (X) for best results when making
changes during recording.
For example: To change channels during recording, first press
PAUSE/STEP (X) to put the unit in pause mode. Then select
the desired channel on the DVD+VCR, and press
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+VCR (page 11),
using a cable box converter, you must set the channel in
this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
with the DVD+VCR.
PAUSE/STEP (X) again to resume recording.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape(Continued)
Use V to choose the SPEED option.
Use b/B to choose the desired recording
speed (AUTO, SP or SLP).
ꢀ AUTO mode determines how much tape is left and
switches speed from SP to SLP, if necessary, to
complete recording the program. There will be some
picture and sound distortion at the point of the speed
change.
Checking (Erasing) the Timer Program
10
Programming can be checked whenever the DVD+VCR
is turned on.
1 Press MENU and the MAIN menu will appear.
2 Use v/V to choose the PROGRAM menu.
Press SELECT/ENTER and the PROGRAM menu
will appear.
Use V to choose the REPEAT option.
Use b/B to choose the desired repeat (ONCE,
WEEKLY or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
11
DAILY event....for recording up to 8 programs at the
same time(s) Monday through Friday.
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen.
Program Priority
If the recording start and end
times of preset programs
overlap on the same day
(see the example and dia-
gram left), program number 2
will not be recorded until pro-
gram number 1 is finished.
Tip
If the input data is wrong, use v to select the data
and correct it using b/B.
The first part of program number 2 will not be recorded.
The same thing will happen to program number 3.
Press MENU, the program will be memorized
at the DVD+VCR.
12
ꢀ
indicator lights in the display window.
ꢀ If the program preset time is past, the PAST TIME
PROGRAMMED message will appear on the TV
screen. Return to the incorrect program and program
it with the correct time.
ꢀ If you had entered a past date, the timer recording
will be performed on that date of the next year.
ꢀ Additional programs may be entered by repeating
steps 1-12.
Cable Users: If your cable hookup is via a TV convert-
er box, you can program multiple recordings only on
the converter box output channel. This is because the
converter determines what channel you view through
your DVD+VCR.
Tip
If you are finished programming and you want to set the
DVD+VCR to record the programs you have entered.
MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. The DVD+VCR is now set to record the preset
programs.
Note
If the power fails or the DVD+VCR is unplugged from the AC
outlet, the correct clock time and timer settings are kept in
memory for approximately 3 seconds. After 3 seconds, the
clock and program timer must be reset when power is
restored. Reset the clock according to instructions.
After setting a timer recording, it will start if a timer recording
passes over the start time when stopping the playback or
recording.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape (Continued)
Instant Timer Recording
Dubbing and Editing
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+VCR, the rear (or Front)
panel mounted Audio and Video (A/V) input jacks
make the connections quick and easy. These direct
A/V jacks will also provide better picture results than
using the RF jack on the rear panel.
Instant Timer Recording allows you to make a recording
easily of a preset length without using the program
timer.
Preparation:
ꢀ Turn on the power of both the DVD+VCR and the TV.
ꢀ Be sure the TV is tuned to the DVD+VCR output channel (3 or 4).
ꢀ If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Connect the camcorder’s (or another VCR’s) A/V
outputs to your DVD+VCR as illustrated on page 13.
1
Set the input channel “LINE2”. (press INPUT to
Insert a video cassette with the safety tab intact.
2 select LINE2.)
1
ꢀ
If you have connected your DVD+VCR to the A/V input
jacks on the rear of DVD+VCR, you should select the
input channel LINE1 by pressing INPUT twice.
Select the desired channel by using CH/TRK
2 (v/V) or number (0-9).
The channel number appears on the TV screen.
ꢀ If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2.
Play the tape in the camcorder (or another
3 VCR). If you have a TV attached to your
DVD+VCR, you can see the video playing.
When you desire recording to begin, press
Set the desired recording speed (SP or SLP) by
3 pressing SP/SLP.
4 DVD+VCR’s REC (z) once to start.
The tape speed will appear on the TV screen.
Note
Press REC (z) twice.
Before recording, please confirm the recording start position.
The menu as illustrated, will appear on the TV screen.
4
ꢀ Recording will start. (The
indicator will light)
Copying from DVD to VCR
Press REC (z) repeatedly to select the record-
5 ing time length.
This unit allows you to copy the contents of a DVD to a
VHS tape.
At the end of the recording, the DVD+VCR will stop
recording and shut off.
Note
ꢀ During Instant Timer Recording, changing the channel
on the DVD+VCR will not be possible.
ꢀ You can stop the recording by pressing STOP (x).
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs. “Lock” is
displayed in the display window.
INSTANT TIMER RECORD MENU
0H30M ..... 9H00M ➝ 0H00M
Insert Disc
INSTANT TIMER RECORD
1
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
CHANNEL
SPEED
2
SP
Length Display
(each additional press of
REC (z) increases recording
time 30 minutes)
Insert VHS Tape
START
LENGTH
NOW
0H30M
2 Insert a blank VHS video tape into the VCR deck.
Press PLAY (H) on the DVD deck.
3 The DVD will go into play mode
Checking the Recording Time
Press REC (z) once to check the recording time. The
recalled setting will automatically return to the TV
screen after 6 seconds.
ꢀ If the DVD disc menu appears, you may need to press
the PLAY (H) manually to begin copying.
Press REC (z) on the VCR deck.
ꢀ The DVD+VCR will go into Record mode.
ꢀ “COPY” indicator will light.
4
To extend the Recording Time
The recording time can be extended anytime by press-
ing REC (z).
Subsequent presses result in advancing the recording
time by 30-minute increments.
Stop the Copy Process
When the DVD is finished playing, press the VCR on the
remote control and then press STOP (x) to end the copy.
You must stop the Copy process manually when the DVD
movie ends, or the unit may replay and record over and
over again.
5
Notes
Note
ꢀ If you press PAUSE/STEP (X) during instant timer record-
ing, the DVD+VCR will enter the recording pause mode.
Instant timer recording is cancelled.
When you stop the DVD playback during copying, the record-
ing on VCR is stopped automatically.
ꢀ If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to
normal recording mode.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape (Continued)
VHS Hi-Fi Stereo System/
MTS Broadcast
MTS (Multi-Channel TV Sound)
This DVD+VCR will decode MTS stereo and bilingual
(SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies,
as long as they operate on assigned cable frequencies
and use the EIA-recommended MTS stereo/bilingual TV
This DVD+VCR is equipped with the VHS Hi-Fi audio
sound system for recording and playback. The informa-
tion below gives a brief description of Hi-Fi audio and
how to record and play a tape in the Hi-Fi audio mode.
sound system.
Playback with Hi-Fi Stereo Audio Sound
Multichannel TV Sound Indicator (MTS)
A stereo TV with AUDIO/VIDEO input jacks or a stereo
audio system is required for true stereo playback. To
experience the full and rich stereo sound available with
Hi-Fi recorded tapes, we recommend the connection of
this unit to a home stereo audio system.
Shows Onscreen as illustrated below when
SELECT/ENTER is pressed.
ꢀ
One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
STEREO
Lights up when a stereo broadcast
is being received.
CH 4
STEREO/SAP
Set the AUDIO MODE option to HI-FI on the
SETUP menu .
1
SAP
Lights up when a SAP BILINGUAL
broadcast is being received.
If only STEREO appears on the TV screen.
The DVD+VCR can record in stereo onto the VHS Hi-Fi audio
tracks when the BROADCAST TYPE option is in the STEREO
position. The DVD+VCR will also record mono audio onto the
mono audio track.
Set the AUDIO OUTPUT option to STEREO
If only SAP appears on the TV screen.
Set the BROADCAST TYPE option to SAP.
2 position.
If STEREO/SAP appears on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP).
(STEREO) POSITION: The left channel sound (L) is
heard from the left speaker and the right channel sound
(R) is heard from the right speaker.
(LEFT) POSITION: The left channel sound (L) is heard
from both speakers.
(RIGHT) POSITION: The right channel sound (R) is heard
from both speakers.
SAP (Second Audio Program) Recording
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
Insert a video cassette with the safety tab intact.
1
Set the BROADCAST TYPE option to SAP
2 (SETUP menu).
Press MENU.
Do this if only the SAP appears on the TV screen or you
know the program will use the SAP.
3
Insert a cassette and press PLAY (H).
4 Adjust volume at your stereo system.
Press MENU.
3
Set the desired recording speed (SP or SLP) by
4 pressing SP/SLP.
Select the desired channel. The SAP should
5 appear on the TV screen.
Press REC (z) once
You are now recording the program you see and hear on the
6
TV.
Press STOP (x) to stop recording.
7
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with tape (Continued)
Tape Counter Memory Feature
Additional Information
ꢀ
ꢀ
ꢀ
ꢀ
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVD+VCR
automatically starts rewinding the tape at the end of the
tape. The cassette will stop at the beginning of the tape and
be ejected, and the DVD+VCR will turn itself off.
Real-Time Counter
Shows length of tape run in hours, minutes, and sec-
onds. Press CLK/CNT to select the real-time counter
display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
After you have finished using the DVD+VCR, rewind, eject,
and remove the cassette. Place the cassette in its protec-
tive sleeve to protect it from dust. It is not necessary to
rewind the cassette before removing it, but if you do, it will
be ready to play or record the next time you use it.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
Be sure the DVD+VCR Channel Selector is on the correct
channel you wish to record. The channel that is being
recorded can always be checked by setting the television
on the DVD+VCR channel (3 or 4) and pressing the
TV/VCR selector to turn the DVD+VCR’s TV indicator off.
REMAINING TIME
ꢀ
ꢀ
ꢀ
Counter changes to “0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is record-
ed on the tape.
The real-time counter will not work unless a tape is
inserted.
Do not attempt to hook up more than one television set to
the DVD+VCR for either recording or playback.
Auto Play System
This DVD+VCR features automatic playback.
Load a cassette (with the safety tab removed).
Counter Memory Function
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
ꢀ
ꢀ
ꢀ
ꢀ
The Output Source is changed to VCR mode automatically.
The power turns on automatically and playback begins.
At the end of the tape, the DVD+VCR stops, then rewinds.
Begin recording or playing a tape.
1
The cassette is ejected after rewinding and turn itself off
automatically.
Press CLK/CNT repeatedly to display the real-
2 time counter appears on the TV screen.
LOAD
AUTO
AUTO
POWER
OFF
AUTO
PLAY
AUTO
At the point that you want locate later, reset the
3 real-time counter to “0:00:00” by pressing
CLEAR.
REWIND
TAPE
EJECT
Continue to play or record.
4
Press STOP (x) when recording or playback fin-
5 ishes.
Press BACKWARD (.).
6 The tape automatically stops when the tape counter
returns to about “0:00:00”.
Tape Remaining
This function allows the time of the remaining tape to be
displayed during recording or playback.
Press CLK/CNT until the REM indicator displays on the
TV screen during recording or playback.
Note
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD
Playing DVD
General Features
Playback Setup DVD
ꢀ Turn on the TV and select the video input source con-
nected to the DVD+VCR.
ꢀ Audio system: Turn on the audio system and select
the input source connected to the DVD+VCR.
ꢀ Set the Output Source to DVD as shown in Setting
the Output Source on page 6.
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
1/3
Moving to another TITLE DVD
When a disc has more than one title, you can move to
another title as follows:
Press OPEN/CLOSE (Z) to open the disc tray.
1
ꢀ
Press DISPLAY when playback is stopped, then
press the appropriate numbered button (0-9) then
press SELECT/ENTER to select a title number.
Load your chosen disc in the tray, with the label
2 facing up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing down.
Moving to another CHAPTER
1/12
Press OPEN/CLOSE (Z) to close the tray.
3 “LOAd” appears in the display window, and play-
back starts automatically. If playback does not start,
press PLAY (H).
DVD
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter as follows:
In some cases, the disc menu might appear
ꢀ Press BACKWARD (.) or FORWARD (>) briefly
during playback to return to the beginning of the cur-
rent chapter or to select the next chapter.
ꢀ Press BACKWARD (.) twice briefly to step back to
the previous chapter.
ꢀ To go directly to any chapter during playback,
press DISPLAY. Then, press v/V to select C
(chapter). Then, enter the chapter number using the
numbered buttons (0-9). Then, press
instead.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD which contains a menu.
DVD
Use b/B/v/V buttons to select the title/chapter you
want to view, then press SELECT/ENTER to start
playback.
SELECT/ENTER.
Press TITLE or DISC MENU to return to the menu
screen.
Slow Motion DVD
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 Press BACKWARD (.) or FORWARD (>)
during pause mode.
The DVD+VCR will enter SLOW mode.
3 Use BACKWARD (.) or FORWARD (>) to
select the required speed: t 1/16, t 1/8, t 1/4 or
t 1/2 (backward), or T 1/16, T 1/8, T 1/4 or T
1/2 (forward).
Notes
ꢀ If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit password
must be entered and/or the disc must be authorized
(see Parental Control, on page 20).
ꢀ DVDs may have a region code.
ꢀ Your DVD+VCR will not play discs that have a region
code different from your DVD+VCR. The region code
for this DVD+VCR is 1 (one).
ꢀ Do not keep an image or on-screen displayed for a
long time.
4 To return to playback, press PLAY (H).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD (Continued)
General Features (continued)
Repeat A-B DVD
A
*
A
B
OFF
Still Picture and Frame-by-frame playback
DVD
To repeat a sequence in a title:
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 With a DVD, you can advance the picture frame by
frame by pressing PAUSE/STEP (X) repeatedly on
the remote control.
1 Press A-B at your chosen starting point.
A- appears briefly on the TV screen.
2 Press A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat
sequence begins
3 To return to playback, press PLAY (H).
3 To cancel the sequence, press A-B.
Search DVD
0:16:57
- : - - : - -
1
Press and hold BACKWARD (.) or FORWARD (>)
for about two seconds during playback.
Time Search DVD
The Time Search function allows you to start playing at
any chosen time on the disc.
The DVD+VCR will now go into SEARCH mode.
Press and hold BACKWARD (.) or FORWARD (>)
repeatedly to select the required speed: mX2, mX4,
mX16, mX100 (backward) or MX2, MX4,
MX16, MX100 (forward).
2
1 Press DISPLAY during playback. The on-screen dis-
play appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
3 To return to playback, press PLAY (H).
2 Within 10 seconds, use v/V to select the Time
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
Random Karaoke DVD
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM” appears on the TV screen.
3 Within 10 seconds, use the numbered buttons to
enter the required start time. Enter hours, minutes
and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
2 To return to normal playback, press RANDOM until
“NORMAL” appears on the TV screen.
4 Within 10 seconds, press SELECT/ENTER.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
Tips
By pressing BACKWARD (.) or FORWARD (>)
during Random playback, the unit selects another title
(track) and resumes Random playback.
NORM.
3D SUR
3D Surround DVD
Note
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multi-
channel audio from a home theater system.
This function only works with DVD Karaoke discs.
OFF
CHAPT
TITLE
Repeat
DVD
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
1 Press DISPLAY during playback.
2 Use v/V to select the sound icon.
The sound option will be highlighted.
3 Use b/B to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM.”.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with DVD (Continued)
General Features (Continued)
Special DVD Features
Zoom DVD
Checking the contents of DVD Video
discs: Menus
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
DVDs may contain menus that allow you to access spe-
cial features. To use the disc menu, press DISC MENU.
Then, press the appropriate number button to select an
option. Or, use b/B/v/V buttons to highlight your selec-
tion, then press SELECT/ENTER.
1 Press ZOOM during playback or still playback to acti-
vate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
2 Use b/B/v/V buttons to move through the zoomed
picture.
DVD
Title Menu
1 Press TITLE.
3 Press CLEAR to resume normal playback or return to
the paused image.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
Note
ꢀ The zoom function may not work for some DVDs.
ꢀ The zoom function may not work on multi-angle
scenes.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TITLE again.
DVD
Marker Search
DVD
Disc Menu
MARKER SEARCH
1/9
1 Press DISC MENU.
The disc menu is displayed.
You can start playback from a memorized point. Up to
nine points can be memorized.
2 To remove the disc menu, press DISC MENU again.
To enter a mark, follow these steps.
1/1
DVD
Camera Angle
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
If the disc contains sequences recorded from different
camera angles, the angle icon blinks on the TV screen.
You can then change the camera angle if you wish.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
ꢀ
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
To Recall a Marked Scene
1 During disc playback, press SEARCH.
DVD
Changing the Audio Language
The Marker Search menu will appear on the screen.
1
ENG
D
2 Within 10 seconds, press 1/2 to select a Marker num-
ber that you want to recall.
5.1CH
3 Press SELECT/ENTER.
Playback will start from the Marked scene.
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
4 To remove the MARKER SEARCH menu, press
SEARCH.
1
ENG
DVD
Subtitles
To clear a Marked Scene
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, press 1/2 to select a Marker num-
ber that you want to erase.
Note
If
appears, the feature is not available on the disc.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with Audio CD and MP3 Discs
CD
Playing an Audio CD and MP3 discs
Search
1 Press and hold BACKWARD (.) or FORWARD
(>) for about two seconds during playback.
The player will now go into SEARCH mode.
The DVD+VCR can play MP3 formatted recordings on
CD-ROM, CD-R, or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Discs on page 32.
2 Press and hold BACKWARD (.) or FORWARD
(>) repeatedly to select the required speed: mX2,
mX4, mX8 (backward) or MX2, MX4, MX8
(forward).
Insert a disc and close the tray.
The menu appears on the TV screen.
1
MP3
Program
CD
Program
3 Search speed and direction are indicated on the
menu screen.
TRACK 1.MP3
TRACK 1
TRACK 2.MP3
TRACK 3.MP3
TRACK 4.MP3
TRACK 5.MP3
TRACK 6.MP3
TRACK 7.MP3
TRACK 8.MP3
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
4 To exit SEARCH mode, press PLAY(H).
Clear All
OFF
Clear All
NORM.
00:00
1
0:56:35
STER.
CD
Random
Audio CD menu
MP3 menu
1 Press RANDOM during playback or when playback is
stopped.
Press 3/4 to select a track then press
The unit automatically begins Random Playback and
“RAND.” appears on the menu screen.
2 PLAY(H).
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window.
Playback will stop at the end of the disc.
2 To return to normal playback, press RANDOM repeat-
edly until “RAND.” disappears on the menu screen.
To stop playback at any other time, press
CD
Repeat A-B
3 STOP(x).
Pause
To repeat a sequence.
1 During disc playback, press A-B at your chosen start-
ing point.
CD
MP3
1 Press PAUSE/STEP (X) during playback.
The Repeat icon and “A -” appears on the menu screen.
2 To return to playback, press PLAY (H) or press
PAUSE/STEP (X) again.
2 Press A-B again at your chosen end point.
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
CD
MP3
Moving to another Track
3 To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “OFF” appear on the menu screen.
ꢀ Press BACKWARD (.) or FORWARD (>) briefly
during playback to go to the next track or to return to
the beginning of the current track.
CD
3D Surround
ꢀ Press BACKWARD (.) twice briefly to step back to
the previous track.
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multi-
channel audio from a home theater system.
ꢀ In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
CD
MP3
1 Press DISPLAY or AUDIO during playback.
Repeat Track/All/Off
2 Use b/B to select the sound icon
The sound icon will be highlighted.
.
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
3 Use v/V to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM.”.
2 To repeat all tracks on a disc, press REPEAT a sec-
ond time.
The Repeat All icon appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
CD
Changing the Audio Channel
Press AUDIO repeatedly during playback to hear a dif-
ferent audio channel (STER., LEFT, or RIGHT).
Note
E
The REPEAT button is not available when the
appears. Press PROGRAM to disappear the
mark
E
mark.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmed Playback
CD
MP3
Programmed Playback with Audio CD
and MP3 Discs
Repeat Programmed Tracks
ꢀ To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
ꢀ To repeat all tracks on the program list, press
REPEAT a second time.
Program allows you to store your favorite tracks for a
particular disc in the player memory.
The Repeat All icon appears on the menu screen.
ꢀ To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
Program can contain 32 tracks (Audio CD) or 60 tracks
(MP3 disc).
Insert the disc and close the tray.
The menu is displayed on the TV screen.
1
Note
Press PROGRAM during playback or in the stop
E
The REPEAT button is not available when the
mark appears.
2 mode to enter the Program Edit mode.
E
Press PROGRAM to disappear the
mark.
E
The
mark will appear to the right of the word Program
on the right side of the menu screen.
Erasing a Track from Program List
Press 3/4 to select a track, then press
3 SELECT/ENTER to place the selected track on
the Program list.
1 Press PROGRAM during playback or in the stop
mode to enter the Program Edit mode.
E
The
mark will appear.
2 Press 2 to move to the Program list.
3 Use 3/4 to select the track that you wish to erase
from the Program list.
Repeat step 3 to place additional tracks on the
4 Program list.
4 Press CLEAR.
CD
Program
E
MP3
Program
E
TRACK 1
TRACK 12
TRACK 8
TRACK 10
TRACK 3
TRACK 1.MP3
TRACK 8.MP3
TRACK 2.MP3
TRACK 4.MP3
TRACK 3.MP3
The track will be erased from the Program list.
5 When finished, Press the PROGRAM to exit the
Program Edit mode.
TRACK 2
TRACK 3
TRACK 4
TRACK 5
TRACK 6
TRACK 7
TRACK 8
TRACK 2.MP3
TRACK 3.MP3
TRACK 4.MP3
TRACK 5.MP3
TRACK 6.MP3
TRACK 7.MP3
TRACK 8.MP3
E
The
mark will disappear.
Clear All
NORM.
Clear All
OFF
0:56:35
STER.
00:00
1
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track from Program
Audio CD menu
MP3 menu
List” as above.
2 Use 3/4 to select “Clear All”, then press
SELECT/ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
When finished, Press the PROGRAM to exit the
5 Program Edit mode.
E
The
mark will disappear.
Press 2.
The programmed track you selected last is highlighted on
the program list.
6
7
To resume normal playback from programmed
playback
Press and hold PROGRAM for 3 seconds until “PROG.”
indicator disappears on the menu screen.
Press 3/4 to select the track you want to start
playing.
Press TITLE to move to the next page.
Press DISC MENU to move to the previous page.
Press PLAY to start.
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the menu screen.
Playback stops after playing the last programmed track on
the program list.
8
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Information - DVD Part
Video Mode Setting DVD
Notes on MP3 Discs
ꢀ With certain discs, the playback picture may be flick-
ering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
About MP3
ꢀ
An MP3 file is audio data compressed by using
MPEG1, the audio layer-3 file-coding scheme. We call
files that have the .mp3 file extension MP3 files.
The DVD+VCR cannot read an MP3 file that has a
file extension other than .mp3.
ꢀ
ꢀ
ꢀ To change the video mode, press and hold DISPLAY
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
The DVD+VCR cannot read a fake MP3 file that has
a file extension .mp3.
MP3 disc compatibility with this DVD+VCR is
limited as follows:
1. Sampling Frequency/only at 44.1kHz
2. Bit rate/within 32 - 320kbps
ꢀ Video mode change sequence:
MODE1 → MODE2 → MODE3 → MODE4 →
MODE5 → MODE1
3. CD-R physical format should be ISO 9660
4. If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example Direct-
CD etc., it is impossible to playback MP3 files. We
therefore recommend that you use Easy-CD
Creator, which creates an ISO9660 file system.
5. A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it can-
not playback MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
ꢀ If you turn off the power, the video mode will be back
to initial state (MODE1).
This player can play the CD-DA Multi-session disc.
But, we cannot guarantee for all other Multi-session
discs.
6. File names should be named using 8 letters or less
and must incorporate the .mp3 extension
e.g. “********.MP3”.
7. Do not use special characters such as
“_?!><+*}{`[@ ]:;\/.,” etc.
8. Total number of files on the disc should be 200 or
less.
If a disc contains more than 200 files, the files with
the numbers 201 or more can not be displayed and
played back.
9. Use 74 minute CD-R discs (650M), do not use 80
minute CD-R (700M) software.
This DVD+VCR requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files).
Customers should also note that permission is required
in order to download MP3 files and music from the
Internet. Our company has no right to grant such per-
mission. Permission should always be sought from the
copyright owner.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
Symptom
No power.
ꢀ The power cord is disconnected.
ꢀ Plug the power cord into the wall outlet
securely.
ꢀ No disc is inserted.
ꢀ No tape is inserted.
ꢀ Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
The power is on, but
the DVD+VCR does not
work.
ꢀ The TV is not set to receive DVD+VCR
signal output.
ꢀ Select the appropriate video input mode
on the TV so the picture from the
No picture.
DVD+VCR appears on the TV screen.
ꢀ TV/VCR mode for DVD+VCR is set to
TV.
ꢀ Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. TV indicator disappears in the
display window.
ꢀ The video cable is not connected
ꢀ Connect the video cable securely.
securely.
ꢀ The connected TV power is turned off.
ꢀ Turn on the TV.
No sound.
ꢀ The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
ꢀ Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
ꢀ The audio cables are not connected
ꢀ Connect the audio cable securely.
securely.
ꢀ The power of the equipment connected
with the audio cable is turned off.
ꢀ Turn on the equipment connected with
the audio cable.
ꢀ The Digital Audio Output is set to the
wrong position.
ꢀ Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
The playback picture is ꢀ The disc is dirty.
ꢀ Clean the disc.
poor.
ꢀ Tape heads are dirty.
ꢀ Clean video heads.
ꢀ Tape is a rental or was recorded on
another VCR.
ꢀ Use CH/TRK (v/V) for manual tracking
adjustment while tape is playing.
ꢀ No disc is inserted.
ꢀ No tape is inserted.
ꢀ Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
The DVD+VCR does
not start playback.
ꢀ An unplayable disc is inserted.
ꢀ Insert a playable disc. (Check the disc
type, color system, and Regional code.)
ꢀ The disc is placed upside down.
ꢀ
Place the disc with the playback side down.
ꢀ The disc is not placed within the guide.
ꢀ Place the disc on the disc tray correctly
inside the guide.
ꢀ The disc is dirty.
ꢀ Clean the disc.
ꢀ The Rating level is set.
ꢀ Cancel the Rating function or change
the rating level.
The remote control
does not work properly.
ꢀ The remote control is not pointed at the
remote sensor of the DVD+VCR.
ꢀ Point the remote control at the remote
sensor of the DVD+VCR.
ꢀ The remote control is too far from the
DVD+VCR.
ꢀ Operate the remote control within 23 ft
(7 m).
ꢀ There is an obstacle in the path of the
ꢀ Remove the obstacle.
remote control and the DVD+VCR.
ꢀ The batteries in the remote control are
ꢀ Replace the batteries with new ones.
exhausted.
ꢀ This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
ꢀ When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
Cause
Correction
Symptom
ꢀ Those channels were deleted with the
CH. ADD/DEL option.
ꢀ Use CH. ADD/DEL. to restore channels.
See “Channel Selection” on page 15.
Some channels are
skipped over when
using CH/TRK (v/V)
ꢀ Antenna or cables are loose.
ꢀ Tighten connections or replace cable.
Picture and sound of
broadcasting channel
are weak or missing.
ꢀ Wrong TUNING BAND option is being
used.
ꢀ Try all TUNING BAND options. See
“Channel Selection” on page 15 for
details.
ꢀ Camcorder is off.
ꢀ Turn camcorder on and operate
properly.
Camcorder image is not
shown.
ꢀ DVD+VCR SOURCE SELECT is not set ꢀ Press INPUT to select LINE input chan-
Camcorder image via
A/V input to DVD+VCR
is not shown on TV
screen.
to LINE1 or LINE2.
nel (LINE1 or LINE2).
ꢀ Clock in DVD+VCR is not set to correct
time.
ꢀ Set clock to correct time. See “Setting
the Clock” on page 16.
Timer recording is not
possible.
ꢀ Timer has been programmed
incorrectly.
ꢀ Reprogram Timer. See “Timer
Recording” on pages 22 and 23.
ꢀ
indicator does not appear after pro-
gramming timer.
ꢀ Reprogram Timer.
ꢀ DVD+VCR is in Timer Recording mode. ꢀ This is the normal indication that the
indicator appears
after DVD+VCR is turned
off.
DVD+VCR is in TIMER mode.
ꢀ TV is not Stereo-compatible.
ꢀ No action is possible.
Stereo Audio Record
and/or Playback is not
present.
ꢀ Broadcast program is not in stereo for-
mat.
ꢀ No action is possible.
ꢀ DVD+VCR A/V Out jacks are not con-
nected to TV A/V In jacks.
ꢀ Make A/V connections. Stereo is
available only via A/V output from
DVD+VCR.
ꢀ DVD+VCR Audio/Video Out is not
ꢀ Select AUX or A/V source as TV input.
selected for viewing at the TV.
ꢀ DVD+VCR BROADCAST TYPE mode is ꢀ Set BROADCAST TYPE mode to
set to SAP or MONO.
STEREO. See “Setting the VCR Setup
Menu” on page 15.
Moisture Condensation
In locations where moisture condensation may occur:
Moisture condensation can occur:
• When the DVD+VCR is moved from a cold place to a
warm place.
•
Keep the DVD+VCR plugged into an AC power outlet
with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+VCR to dry before using it.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 18).
Language
Abkhazian
Afar
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
Language
Fiji
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
Language
Lingala
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Finnish
French
Lithuanian
Macedonian
Malagasy
Malay
Afrikaans
Albanian
Amharic
Arabic
Frisian
Galician
Georgian
German
Greek
Malayalam
Maltese
Maori
Armenian
Assamese
Aymara
Greenlandic
Guarani
Gujarati
Hausa
Marathi
Azerbaijani
Bashkir
Moldavian
Mongolian
Nauru
Tamil
Basque
Tatar
Bengali; Bangla 6678
Hebrew
Hindi
Nepali
Telugu
Thai
Bhutani
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Norwegian
Oriya
Bihari
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Tibetan
Tigrinya
Tonga
Breton
Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Pashto, Pushto 8083
Persian
7065
8076
8084
8185
Turkish
Turkmen
Twi
Polish
Italian
Portuguese
Quechua
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Ukrainian
Urdu
Rhaeto-Romance 8277
Romanian
Russian
8279
8285
8377
8365
7168
8382
Uzbek
Vietnamese
Volapük
Welsh
Samoan
Danish
Sanskrit
Dutch
Korean
Kurdish
Laothian
Latin
Scots Gaelic
Serbian
Wolof
English
Xhosa
Esperanto
Estonian
Faeroese
Serbo-Croatian 8372
Yiddish
Yoruba
Zulu
Shona
Sindhi
8378
8368
Latvian, Lettish 7686
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power requirements
AC 120V , 60 Hz
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
23W
430 X 97.5 X 293 mm (16.9 x 3.9 x 11.5 inches) (w x h x d)
4.8 kg (10.58 lbs)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VHS VIDEO IN
VHS AUDIO IN
Antenna or CATV input, 75 ohms
1 Vp-p 75 ohms, sync negative, RCA jack x 1
-6.0 dBm more than 47 kohms, RCA jack (L, R) x 1
Outputs
VIDEO OUT
1 Vp-p 75 ohms, sync negative
S-VIDEO OUT
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 ohms
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA jack (L, R) x 1
Channel 3 or 4
Audio output (digital audio)
Audio output (analog audio)
RF OUT
VCR Specifications
Head system
Timer
Tape speed
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
Tape width
Maximum recording time
Rewind time
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
Antenna
75 ohms (VHF/UHF)
VHF output signal
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Channel 3 or 4 (Switchable)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20Hz to 20kHz
More than 43dB
More than 88 dB
More than 60 dB
DVD Specifications
Laser system
Frequency response
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio
Harmonic distortion
Dynamic range
More than 100dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (DVD/CD)
Accessory:
Video cable x 1, Audio cable x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries x 2
ꢀ Design and specifications are subject to change without notice.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|