Savin Printer 3360DNP User Guide

Operating Instructions

For safety, please read this manual carefully before you use this product and keep it

handy for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note to users in the United States of America

Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-

ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television re-

ception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio /TV technician for help.

Warning

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

Note to users in Canada

Note:

This Class B digital apparatus complies with Canadian ICES-003.

Remarque concernant les utilisateurs au Canada

Avertissement:

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

In accordance with IEC 60417, this machine uses the following symbols for the main switch:

a means POWER ON.

b means POWER OFF.

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

This manual describes detailed instructions on the operation and notes about the use of this machine.

To get maximum versatility from this machine all operators are requested to read this manual carefully

and follow the instructions. Please keep this manual in a handy place near the machine.

Notes:

Some illustrations in this manual might be slightly different from the machine.

Certain options might not be available in some countries. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the inch version.

For good print quality, Standard recommends that you use genuine Standard masters and inks.

Standard shall not be responsible for any damage or expense that might result from the use of parts

other than genuine Standard parts in your Standard office product.

Power Source

120V, 60Hz, 3.2A or more

Please be sure to connect the power cord to a power source as above. For details about power source,

⇒ p.196 “Power Connection”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information

When using this machine, the following safety precautions should always be fol-

lowed.

Safety During Operation

In this manual, the following important symbols are used:

R WARNING:

Indicates a potentially hazardous situation which, if instructions

are not followed, could result in death or serious injury.

R CAUTION:

Indicates a potentially hazardous situation which, if instructions are not

followed, may result in minor or moderate injury or damage to property.

R WARNING:

• Connect the power cord directly into a wall outlet and never use an ex-

tension cord.

• Disconnect the power plug (by pulling the plug, not the cable) if the

power cable or plug becomes frayed or otherwise damaged.

• To avoid hazardous electric shock, do not remove any covers or

screws other than those specified in this manual.

• Turn off the power and disconnect the power plug (by pulling the plug,

not the cable) if any of the following occurs:

• You spill something into the machine.

• You suspect that your machine needs service or repair.

• The external housing of your machine has been damaged.

Download from Www.Somanuals.com. All Manuals Search And Download.

R CAUTION:

• Protect the machine from dampness or wet weather, such as rain, snow.

• Unplug the power cord from the wall outlet before you move the machine.

While moving the machine, you should take care that the power cord will not

be damaged under the machine.

• When you disconnect the power plug from the wall outlet, always pull the

plug (not the cable).

• Do not allow paper clips, staples, or other small metallic objects to fall inside

the machine.

• For environmental reasons, do not dispose of the machine or expended

supply waste at household waste collection points. Disposal can take place

at an authorized dealer.

• Be careful not to cut yourself on any sharp edges when you reach inside the

machine to remove misfed sheets of paper or masters.

• Our products are engineered to meet high standards of quality and function-

ality, and we recommend that you use only the expendable supplies avail-

able at an authorized dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Read This Manual

Symbols

In this manual, the following symbols are used:

R WARNING:

This symbol indicates a potentially hazardous situation that might result in

death or serious injury when you misuse the machine without following the in-

structions under this symbol. Be sure to read the instructions, all of which are de-

scribed in the Safety Information section.

R CAUTION:

This symbol indicates a potentially hazardous situation that might result in mi-

nor or moderate injury or property damage that does not involve personal injury

when you misuse the machine without following the instructions under this

symbol. Be sure to read the instructions, all of which are described in the Safety

Information section.

* The statements above are notes for your safety.

Important

If this instruction is not followed, paper might be misfed, originals might be

damaged, or data might be lost. Be sure to read this.

Preparation

This symbol indicates the prior knowledge or preparations required before op-

erating the machine.

Note

This symbol indicates precautions for operation, or actions to take after misop-

eration.

Limitation

This symbol indicates numerical limits, functions that cannot be used together,

or conditions in which a particular function cannot be used.

Reference

This symbol indicates a reference.

[

]

Keys that appear on the machine's display panel.

{

}

Keys built into the machine's operation panel.

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Making Prints

Before making prints using this ma-

chine, you have to make a master by

pressing the {Start} key. When you

press the {Start} key, the machine

scans the original image and makes a

master. This procedure describes

how to make basic prints.

B Press the {Start} key.

A Place your originals in one of the

following two ways:

Placing originals on the exposure

glass

C Press the {Proof} key.

A Place a single page face down.

Check the print image.

ZDCH110E

Reference

For changing the image posi-

tion, see p.24 “Adjusting the Po-

sition of Printed Images”.

Inserting originals in the optional

document feeder

A Insert a stack of originals face

up.

To increase the image density,

press the {W} key. See p.25 “Ad-

justing the Image Density of

Prints”.

ZDCH120E

Note

❒ To avoid jamming, fan the

originals before placing them

in the document feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

To decrease the image density,

press the {V} key. See p.25 “Ad-

justing the Image Density of

Prints”.

D Enter the desired number of

prints with the number keys.

E Press the {Print} key.

When the print job has finished,

press the {Clear Modes/Energy Sav-

er} key. Previously entered job set-

tings will be cleared.

Download from Www.Somanuals.com. All Manuals Search And Download.

What You Can do with this Machine

Below is a quick summary of this ma-

chine's features and where to look in

this manual for more information.

❖ Reducing and Enlarging Using Preset

Ratios

See p.29 “Reducing and Enlarging

Using Preset Ratios”.

❖ Standard Printing

See p.19 “Standard Printing”.

❖ Energy Saver Mode

See p.22 “Energy Saver Mode”.

❖ Adjusting the Print Image Position

See p.24 “Adjusting the Position of

Printed Images”.

GRRATI0E

❖ Auto Magnification

See p.31 “Auto Magnification”.

GRPOSI0E

* Paper feed direction

❖ Adjusting the Print Image Density

See p.25 “Adjusting the Image

Density of Prints”.

GRAUTO0E

❖ Zoom

See p.34 “Zoom”.

❖ Tint Mode

See p.26 “Tint Mode”.

GRZOOM0E

GRTINT0E

❖ Changing the Printing Speed

See p.27 “Changing the Printing

Speed”.

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ Directional Magnification (%)

See p.36 “Directional Magnifica-

tion (%)”.

❖

Economy Mode

See p.50 “Economy Mode”.

❖ Auto Cycle

See p.51 “Auto Cycle”.

❖ All Class Mode

See p.52 “All Class Mode”.

CP2P01EE

❖ Directional Magnification (Size)

See p.38 “Directional Magnifica-

tion (Size)”.

GRCLAS2E

❖ Auto Class Mode

See p.54 “Auto Class Mode”.

CP2M01EE

❖ Erasing Center and Edge Margins

See p.40 “Erasing Center and Edge

Margins”.

GRCLAS2E

❖ Manual Class Mode

See p.57 “Manual Class Mode with

❖ Edge Erase

See p.41 “Edge Erase”.

One Original”.

GRERAS0E

❖ Printing on Various Kinds of Paper

See p.43 “Printing onto Various

Kinds of Paper”.

GRCLAS2E

❖ Selecting Original Modes

See p.46 “Selecting Original

Modes”.

vii

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ Manual Class Mode with two or More

Originals

❖

Auto Combine Mode

See p.68 “Auto Combine Mode”.

See p.59 “Manual Class Mode with

two or More Originals”.

1 1

A B

C D

GRACOM0E

GRCLAS1E

❖ Skip Feed Printing

See p.70 “Skip Feed Printing”.

❖ Class Mode

See p.61 “Class Mode”.

❖ Programs

See p.72 “Programs”.

❖ Security Mode

See p.75 “Security Mode”.

R R R

❖ Quality Start Mode

See p.76 “Quality Start Mode”.

R R R

❖ Job Separation

See p.77 “Job Separation”.

GRCLAS0E

❖ Combining Originals

See p.63 “Combine Originals”.

1 2

GRJOBS0E

❖ Conserving the Master

See p.79 “Conserving the Master”.

GRCOMB2E

❖ On Line Printing

See p.80 “On Line Printing”.

❖ Making Color Prints

See p.130 “Making Color Prints”.

viii

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ Printing in Two Colors

See p.132 “Printing in Two Col-

ors”.

❖

Date Stamp

See p.108 “Date Stamp”.

GRCOLO0E

❖ Page Stamp

See p.110 “Page Stamp”.

❖ Image Rotation

See p.82 “Image Rotation”.

❖ Make-up Printing

See p.94 “Make-up Printing”.

❖ Merging Images

See p.105 “Image Overlay”.

– 1 –

GRPAGE0E

ABCDE ABCDE ABCDE ABCDE ABCDE

❖ Stamp

See p.113 “Stamp”.

Priority

GROVER0E

Preliminary

Confidential

GRSTAM0E

GROVER1E

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ Memory Combine

See p.115 “Memory Combine”.

GRMCOM0E

GRREPE0E

❖ Original Storage

See p.100 “Original Storage”.

❖ Storage Overlay

See p.105 “Image Overlay”.

ABCDE ABCDE ABCDE ABCDE ABCDE

GROVER0E

GROVER1E

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Machine Exterior......................................................................................... 1

Machine Interior.......................................................................................... 2

Options........................................................................................................ 4

Operation Panel.......................................................................................... 6

Keys ............................................................................................................... 6

Indicators........................................................................................................ 8

Panel Display.............................................................................................. 9

Panel Display Layout ................................................................................... 10

1.Operation

Print Paper ................................................................................................ 11

Originals.................................................................................................... 13

Printing Preparations............................................................................... 15

Loading Paper.............................................................................................. 15

Setting Up The Paper Delivery Tray ............................................................ 16

Entering a User Code to Use the Machine............................................. 18

Standard Printing ..................................................................................... 19

Removing Prints........................................................................................... 20

Energy Saver Mode.................................................................................. 22

Auto Reset................................................................................................. 23

Adjusting the Position of Printed Images .............................................. 24

Adjusting the Image Density of Prints.................................................... 25

Before Making a Master............................................................................... 25

After Making a Master.................................................................................. 25

Tint Mode................................................................................................... 26

Changing the Printing Speed .................................................................. 27

Stopping a Multi-print Run ...................................................................... 28

Stopping a Multi-print Run to Print Another Original .................................... 28

Changing the Number of Prints Entered and Checking Completed Prints... 28

Reducing and Enlarging Using Preset Ratios ....................................... 29

Auto Magnification ................................................................................... 31

Zoom.......................................................................................................... 34

Directional Magnification (%) .................................................................. 36

Directional Magnification (Size) .............................................................. 38

Erasing Center and Edge Margins.......................................................... 40

Edge Erase................................................................................................ 41

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing onto Various Kinds of Paper..................................................... 43

Printing onto Thick Paper............................................................................. 43

Printing onto Standard Paper....................................................................... 43

Printing onto Envelopes ............................................................................... 44

Printing onto Special Kinds of Paper............................................................ 44

Selecting Original Modes......................................................................... 46

Letter/Photo Mode Printing .......................................................................... 46

Photo Mode Printing..................................................................................... 47

Pencil Mode Printing .................................................................................... 48

Economy Mode......................................................................................... 50

Auto Cycle................................................................................................. 51

All Class Mode.......................................................................................... 52

Auto Class Mode ...................................................................................... 54

Manual Class Mode with One Original ................................................... 57

Manual Class Mode with two or More Originals.................................... 59

Class Mode................................................................................................ 61

Combine Originals.................................................................................... 63

Auto Combine Mode................................................................................. 68

Skip Feed Printing.................................................................................... 70

Programs................................................................................................... 72

Storing a Program........................................................................................ 72

Protecting a Program ................................................................................... 73

Removing Program Protection..................................................................... 73

Recalling a Program..................................................................................... 74

Security Mode........................................................................................... 75

Quality Start Mode.................................................................................... 76

Using Quality Start Manually........................................................................ 76

Job Separation.......................................................................................... 77

Conserving the Master............................................................................. 79

On Line Printing........................................................................................ 80

Auto On Line ................................................................................................ 81

Image Rotation.......................................................................................... 82

Make-up Printing Features ...................................................................... 83

Main Features .............................................................................................. 83

Make-up Modes for Designated Areas......................................................... 83

Make-up Modes for Outside Designated Areas ........................................... 85

Background Patterns.................................................................................... 86

Command Sheets for Make-Up Printing................................................. 87

Command Sheets ........................................................................................ 87

Making a Command Sheet........................................................................... 87

Command Sheets and Finished Prints......................................................... 92

xii

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Printing ...................................................................................... 94

Make-up Samples..................................................................................... 97

Original Storage...................................................................................... 100

Storing Originals......................................................................................... 100

Selecting Stored Originals.......................................................................... 102

Protecting Stored Originals ........................................................................ 102

Deleting Stored Originals ........................................................................... 103

Image Overlay......................................................................................... 105

Storage Overlay ......................................................................................... 105

On Line Overlay ......................................................................................... 106

Overlay Format .......................................................................................... 106

Date Stamp.............................................................................................. 108

Page Stamp............................................................................................. 110

Stamp....................................................................................................... 113

Memory Combine ................................................................................... 115

Combining onto a Single–sided Print......................................................... 115

Repeat........................................................................................................ 120

2.Optional Functions

Optional Document Feeder.................................................................... 125

Originals..................................................................................................... 125

Placing Originals ........................................................................................ 126

Combine Printing........................................................................................ 127

Manual Class Mode with Two or More Originals........................................ 128

Color Printing Using the Optional Color Drum.................................... 130

Making Color Prints.................................................................................... 130

Changing the Color Drum Unit................................................................... 130

Printing in Two Colors................................................................................ 132

Changing the Drum Size........................................................................ 134

Printing Area (At 23°C/73°F, 65% RH)....................................................... 134

Master Cut Length...................................................................................... 134

3.Combination Chart

Combination Chart ................................................................................. 135

xiii

Download from Www.Somanuals.com. All Manuals Search And Download.

4.User Tools

Accessing the User Tools...................................................................... 139

User Tools Menu..................................................................................... 141

1. System ................................................................................................... 141

2. Set Operat'n Mode ................................................................................. 142

3. Initial Setting........................................................................................... 143

4. Mode Setting.......................................................................................... 144

5. Stamp..................................................................................................... 148

6. Administrator Mode................................................................................ 150

7. On Line Mode......................................................................................... 151

User Tool Menus in Detail...................................................................... 153

1-6 Time Setting......................................................................................... 153

3-4 Reproduction Ratio .............................................................................. 154

3-5 Class Enter No..................................................................................... 154

3-11 Margin Erase Area............................................................................. 155

4-11 No. of Skip Feed ................................................................................ 156

4-14 No. of Q.start...................................................................................... 157

4-19 Type of Paper .................................................................................... 158

5-4 Stamp Position..................................................................................... 159

5-7 Position (Date) ..................................................................................... 160

5-10 Position (Page) .................................................................................. 161

5-11 Make/Chg. Pattern............................................................................. 163

6-1 Check Counter..................................................................................... 164

6-2 Reset Counters.................................................................................... 164

6-5 Chg. User Code ................................................................................... 165

6-6 Del. User Code .................................................................................... 166

5.Troubleshooting

If Your Machine Does Not Operate as You Want................................. 167

If You Cannot Make Prints as You Want .............................................. 169

Combine Originals Mode............................................................................ 169

Loading Paper......................................................................................... 170

x Clearing Misfeeds.............................................................................. 171

”x + A” Paper Misfeeds in the Paper Feed Section.................................. 171

”x + A + B” Paper Misfeeds in the Paper Feed Section ........................... 172

”x + B” Paper or Master Wrapped Around the Drum................................ 173

”x + C” Paper Misfeeds in the Paper Exit Section.................................... 175

”x + D” Master Misfeeds in the Master Feed Section............................... 176

”x + D + B” Master Misfeeds in the Master Feed Section ........................ 176

”x + B + E” Master Misfeeds in the Master Eject Section......................... 177

”x + E” Master Misfeeds in the Master Eject Section ............................... 178

”x

+ P” Original Misfeeds Occur When Using the Optional Document Feeder ... 179

When the Open Cover/Unit Indicator (M) Lights................................. 181

When the Add Ink Indicator (j) Lights................................................ 182

xiv

Download from Www.Somanuals.com. All Manuals Search And Download.

When the Master End Indicator (C) Lights.......................................... 184

When the Master Eject Indicator (k) Lights........................................ 186

When Other Indicators Are Lit............................................................... 187

When Prints Are Not Delivered in a Neat Stack................................... 188

When Printing on Small Size Paper........................................................... 188

When the Machine Cannot Detect the Paper Size..................................... 188

Poor Printing........................................................................................... 189

Dirty Background........................................................................................ 189

Black Lines/Stained Prints ......................................................................... 192

Faint Prints................................................................................................. 192

6.Remarks

Do's and Don'ts ...................................................................................... 193

Where to Put Your Machine................................................................... 195

Environment............................................................................................... 195

Power Connection...................................................................................... 196

Machine Clearance .................................................................................... 196

Maintaining Your Machine..................................................................... 197

Cleaning the Main Frame........................................................................... 197

Cleaning the Optional Document Feeder................................................... 198

7.Specifications

Main Frame.............................................................................................. 199

Document Feeder (Option) .................................................................... 203

Color Drum Type 55(L) A3, 11" × 17" (Option)..................................... 203

Color Drum Type 55(S) A4, 8 / " × 11" (Option) .................................. 203

Exposure Glass Cover (Option)............................................................ 203

Printer Unit Type 80 RCP80 (Option).................................................... 203

Interface Cable Type 85 (Option) .......................................................... 203

Editing Function Type 85 (Option)........................................................ 203

Twin Color Press Roller Printing System TC-II (Option)..................... 204

Consumables.......................................................................................... 205

INDEX....................................................................................................... 206

Download from Www.Somanuals.com. All Manuals Search And Download.

xvi

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Exterior

1. Front door

Open to access the inside of the machine.

5. Paper feed tray down key

Press to lower the paper feed tray.

2. Flip up cover

Flip up to access the keys underneath.

6. Paper feed side plates

Prevent paper skewing.

3. Operation panel

See p.6 “Operation Panel”.

7. Paper feed tray

Load paper here.

4. Master tray

Open this unit when installing the mas-

ter.

8. Paper feed side plates knob

Use to move the side plates.

Download from Www.Somanuals.com. All Manuals Search And Download.

Machine Interior

ZBHH180E

1. Main switch

Use to turn the power on or off.

5. Paper delivery tray

Completed prints are delivered here.

2. Paper alignment wings

Lift or lower the wings depending on the

type of paper being used.

6. Paper delivery side plates

These plates align the prints on the paper

delivery tray.

3. Paper delivery end plate

7. Paper delivery side plate knobs

This plate aligns the leading edge of

prints.

Use to move the side plates.

8. Handle E1

Use to pull out the master eject unit.

4. Paper delivery end plate knob

Use to move the end plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Ink holder

Set the ink cartridge in this holder.

10. Drum unit lock lever B1

Lower to unlock and pull out the drum

unit.

11. Drum unit

The master is wrapped around this unit.

12. Exposure glass

Position originals here face down for

printing.

13. Exposure glass cover or docu-

ment feeder (option)

Lower this cover over an original on the

exposure glass.

14. Trailing edge guides

Swing out these guides when you use A4,

8¹/₂" × 11"KL paper.

Download from Www.Somanuals.com. All Manuals Search And Download.

Options

❖ Exposure glass cover

1. Exposure glass cover

❖ Document feeder

1. Document Feeder

Download from Www.Somanuals.com. All Manuals Search And Download.

❖ Twin color press roller printing system TC-II

Note

❒ Other options:

• Color Drum Type 55(L) A3, 11" × 17"

• Color Drum Type 55(S) A4, 8¹/₂" × 11"

• Exposure Glass Cover

• Printer Unit Type 80 RCP80

• Interface Cable Type 85

• Editing Function Type 85

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Panel

Keys

Auto On Line

lay

Original Storage

ZDZS200N

1. {Quality Start} key

9. {Image Density} key

See p.76 “Quality Start Mode”.

Press to make prints darker or lighter. See

p.25 “Adjusting the Image Density of

Prints”.

2. {Security} key

See p.75 “Security Mode”.

10. {Economy Mode} key

Press to save ink. See p.50 “Economy

Mode”.

3. {Skip Feed} key

Press to select skip feed printing. See p.70

“Skip Feed Printing”.

11. {Original Storage} key

Press to select the Original Storage func-

tion. See p.100 “Original Storage”.

4. {User Tools} key

Press to change the default settings to

meet your requirements.

12. {On Line} key

See p.80 “On Line Printing”.

5. {Stamp} key

Press to select the Stamp mode. See p.108

“Date Stamp”, see p.110 “Page Stamp”,

see p.113 “Stamp”.

13. {Auto On Line} key

See p.80 “On Line Printing”.

6. {Make-Up} key

Press to select the Make-up mode. See

14. {Job Separator} key

See p.77 “Job Separation”.

p.94 “Make-up Printing”.

15. {Combine} key

7. {Overlay} key

Press to select the Image Overlay mode.

See p.105 “Image Overlay”.

Press to combine originals onto one print.

See p.63 “Combine Originals”, see p.115

“Memory Combine”, see p.68 “Auto

Combine Mode”.

8. {Edge Erase} key

Press to select Edge Erase mode. See p.41

“Edge Erase”.

Download from Www.Somanuals.com. All Manuals Search And Download.

16. {

Class} key

Press to select All Class, Auto Class,

Manual Class, or Class mode. See p.52

“All Class Mode”, see p.54 “Auto Class

Mode”, see p.57 “Manual Class Mode

with One Original”, see p.59 “Manual

Class Mode with two or More Originals”,

see p.61 “Class Mode”.

17. {W} {V} keys (Speed keys)

Press to adjust the printing speed. See

p.25 “Adjusting the Image Density of

Prints”, see p.27 “Changing the Printing

Speed”.

18. {~}{}}{|}{{} keys

Press to shift the image forward, back-

ward, right, or left. See p.24 “Adjusting

the Position of Printed Images”.

Also use to highlight items you wish to

select on the panel display.

19. {Program} key

Press to enter or recall programs. See p.72

“Programs”.

20. Number keys

Press to enter the desired number of

prints and data for selected modes.

21. {Clear/Stop} key

Press to stop printing.

22. {q} key

Use to enter data in selected modes.

23. {Clear Modes/Energy Saver} key

Press to clear any previously entered job

settings.

24. {Start} key

Press to make a master.

25. {Auto Cycle} key

Use to process the master and make

prints in one operation. See p.51 “Auto

Cycle”.

26. {Proof} key

Press to make proof prints.

27. {Print} key

Press to start printing.

Download from Www.Somanuals.com. All Manuals Search And Download.

Indicators

1. Special feature indicator

6. Counter

Lights to indicate that special features

have been selected. To access the special

features, lift up the cover on the left side

of the operation panel.

Displays the number of prints entered.

While printing, it shows the number of

prints remaining.

7. Panel display

See p.9 “Panel Display”.

2. Monitor indicators

These indicators light to inform you of

the status of the machine. See p.167 “If

Your Machine Does Not Operate as You

Want”.

8. Data In indicator (Green)

Indicates the status of this machine:

• On: Data waiting for Master Making

and printing is in the machine.

3. A3/11" × 17" drum indicator

Lights when the A3, 11" × 17" drum unit

is installed. See p.134 “Changing the

Drum Size”.

• Blinking: Data is being received, or

Master Making or printing is in

progress.

• Off: Master Making and printing are

4. A4, 8¹/₂" × 11" drum indicator

completed.

Lights when the A4, 8¹/₂" × 11" drum unit

is installed. See p.134 “Changing the

Drum Size”.

9. Error indicator (Red)

Indicates the status of this machine:

• On: An error has occurred. Master

Making and printing stops.

• Off: Normal status

5. Color drum indicator

Lights when the color drum unit is in-

stalled. See p.130 “Color Printing Using

the Optional Color Drum”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Display

The panel display shows the machine status, error messages, and function

menus.

ZBZX170N

1. Items for the selected function

3. Machine status or messages

2. These keys correspond to the se-

lectable items shown above them on

the panel display. To select an item

shown on the panel display, press

the key directly below it.

4. Items which can be selected

Important

❒ Strong impact or pressure exceeding 30N will damage the panel display.

Note

Auto

❒ When you select an item on the panel display, it is highlighted (e.g.

Items shown grayed-out (e.g.

) cannot be selected.

❒ Common panel display items

[OK]

Confirms a function selection or enters a value.

[Cancel]

Cancels a function selection or entered value and returns to

the previous display.

[Prev.][Next]

When there are too many items to fit on the panel display, use

these keys to move between pages.

{~}{}}{|}{{}[←][→]

Press to highlight items you wish to select on the panel dis-

play.

[Select]

Selects a value.

[Exit]

Returns to the previous display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Panel Display Layout

The basic elements used on the panel display are shown below. Understanding

their meaning helps you use this machine's features quickly and easily.

❖ Sample display when selecting the [Original] key

ZBZX180N

1. Machine status or message

2. Available functions

3. Illustrations of displays in this

manual show the next key to be

pressed whitened

When the [Original] key is pressed, the following display is shown.

1. Available functions

2. Confirms the settings

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Operation

Print Paper

The following limitations apply

Paper Size

Inch

Paper

Weight

Metric

11" × 17" L, 8¹/₂" × 14" L,

Paper feed tray A3 L, B4 L, A4 L K, B5 L K,

A5 L, B6 L, A6 L, Others (Ver-

tical: 70 - 297mm, Horizontal: 148

- 432mm)

47.1 -

209.3g/m²,

12.5 - 55.6 lb

8¹/₂" × 11" L K, 5¹/₂" ×

8¹/₂" L K, Others (Verti-

cal: 2.76" - 11.7", Horizon-

tal: 5.83" - 17")

Non-recommended paper:

• Roughly cut paper

• Paper of different thickness in the same stack

• Envelopes heavier than 85g/m², 22 lb.

• Folded, curled, creased, or damaged paper

• Torn paper

• Slippery paper

• Rough paper

• Paper with any kind of coating (such as carbon)

• Short grain paper

• Thin paper that has low stiffness

• Paper that may create a lot of dust

• Grained paper with the direction of the grain running opposite to the feed di-

rection

• Certain types of long thin envelopes.

E.g. international mail envelopes

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

• The following types of envelopes

Note

❒ If you print on rough grained paper, the copy image might be blurred.

❒ You can use A3 (297 × 420mm) or 11" × 17" originals or printing paper. When

you want to print the entire image of an A3, 11" × 17" original, select Reduce

mode because the maximum print areas are as follows:

• Metric version: 290 × 409mm, 11.4" × 16.1"

• Inch version: 290 × 419mm, 11.4" × 16.4"

❒ When you use A3, 11" × 17" and 209.3g/m², 55.6 lb paper, slow the printing

speed down to setting 1, 2, or 3.

Important

❒ Correct curls in the paper before placing it in the machine. When you cannot

correct the paper curl, stack the paper with the curl face down or face up as

shown in the illustration. If the paper is curled, it might wrap around the

drum or stains might appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Originals

The machine can detect the following original sizes placed on the exposure glass.

Metric version

Inch version

A3L, B4L, A4KL, B5KL

11" × 17"L, 8¹/₂" × 14"L, 8¹/₂" × 11"KL

Reference

For the original sizes placed in the document feeder can be detected, see p.125

“Optional Document Feeder”.

If the machine cannot detect the original sizes properly, select the area to copy

with the {Edge Erase} key. See p.41 “Edge Erase”. The machine may not detect

the original size properly when:

• Originals contain index tabs.

• Originals are OHP transparencies or are translucent.

• Originals are dark.

• Originals contain solid images.

• Originals are of sizes other than those listed above.

If you do not lift the exposure glass cover more than 30cm, 12" when you place

another original, the machine might not detect the next original size correctly.

The maximum original size you can place on the exposure glass is 304.8 ×

432mm, 12" × 17".

If you use originals that have bold letters or solid images at the leading edges,

you might get prints with dirty edges. In this case, place the original face down

with the widest margin toward the paper delivery tray or raise the printing

speed.

Make sure any correction fluid or ink is completely dry before placing originals

on the exposure glass. Not taking this precaution could mark the exposure glass

and cause marks to be printed.

In most situations, place originals as shown below.

R R

ZDZX030E

When the original is placed in a direction that differs from the print paper, the

machine automatically rotates the original image by 90° to match the print paper

direction.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

The first 8mm, 0.32", of the leading edge and the last 2mm, 0.08", of the trailing

edge cannot be printed. Make sure the leading edge margin is at least 8mm,

0.32", and the trailing edge margin is at least 2mm, 0.08".

Original

a = 8mm, 0.32"

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing Preparations

D Place the paper on the paper feed

Loading Paper

tray.

A Carefully open the paper feed

tray.

Note

ZDCY130E

❒ Correct the paper curl before

loading the paper. If you cannot

do so, stack the paper with the

curl face down.

B Lift the paper feed side plates.

Reference

See p.11 “Print Paper”.

E Make sure that the paper feed

side plates touch both sides of the

paper lightly.

C Grasp the paper feed side plates

knob and adjust the paper feed

side plates to match the paper

size.

Note

❒ Make sure that the paper size

and direction in the panel dis-

play correspond with the actual

paper size and direction set on

the paper feed tray.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

When you use standard paper

(47.1 g/m²to 105 g/m², 12.5 lb to

28 lb)

Setting Up The Paper Delivery

Tray

A Adjust the side plates to match

the paper size scale on the end

plate side.

A Raise the paper delivery tray

slightly, and then gently lower it

with your hand.

C Lower or lift the paper alignment

wings by turning the left and

right knobs.

ZBHH050E

B Raise each paper delivery side

plate, and then grasp the side

plate knobs and move the paper

delivery side plates to match the

print paper size.

Note

❒ When the guides are up, you

might not be able to load the

unit to full capacity (1,000

sheets) depending on the paper

you are using.

❒ Lift the paper alignment wings

if B5L prints are curled.

When you use 81.4 g/m², 21.6 lb

or thicker paper

ZDZH180E

Note

Lower the paper alignment wings.

❒ The inside of the plates should

correspond to the paper size.

When you use 81.4 g/m², 21.6 lb

or thinner and B5 or smaller paper

Whenyouusethickpaper (128g/m²

to 209.3 g/m², 34 lb to 55.6 lb)

Lower the paper alignment wings.

A Adjust the side plates to match

the paper size scale on the

main frame side.

When you use 81.4 g/m², 21.6 lb

or thinner and A4, 8¹/₂× 11" or

larger paper

Lift the paper alignment wings.

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing Preparations

When you use A4, 8 ¹/₂"

paper

11"KL

A Swing out the guides as shown

in the illustration.

ZDZY020E

D Turn on the main switch.

TPEH021E

Note

❒ You can have the machine dis-

play how much ink and master

are left when you switch it on.

See “User Tools—Ink/Master

Left” on p.144 “4. Mode Set-

ting”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Entering a User Code to Use the Machine

If user codes are turned on, operators

B Press the {q} key.

must enter their user code before they

can use the machine. The machine

keeps count of the number of copies

made under each user code.

Note

❒ If you want to use this feature, you

must turn it on and register the

user codes with the user tools. You

can register up to 20 user codes.

See “Set User Code” and “Reg.

User Code” on p.150 “6. Adminis-

C Make your prints.

trator Mode”.

D To prevent others from making

prints with your user code, hold

downthe{ClearModes/EnergySaver}

key,andthenpressthe{Clear/Stop}

key.

❒ When user codes are turned on,

the machine will prompt you for

your user code when you turn on

the main switch or after the ma-

chine has been reset.

A Enter your 4–digit user code with

the number keys.

Note

❒ User codes are not displayed on

the panel display.

❒ To change the number entered,

pressthe{Clear/Stop}keyanden-

ter the new number.

Download from Www.Somanuals.com. All Manuals Search And Download.

Standard Printing

A Make sure that the machine is E Place the original face down on

ready for printing.

the exposure glass. The original

should be aligned with the refer-

ence mark and the left corner

scale.

B If user codes are turned on, enter

your user code with the number

keys, and then press the {q} key.

Reference

See p.18 “Entering a User Code

to Use the Machine”.

C Make sure that there are no previ-

1. Left corner scale

2. Reference mark

ous settings remaining.

Note

❒ To clear any previous settings,

press the {Clear Modes/Energy

Saver} key.

F Lower the exposure glass cover.

G Make your desired settings.

H Press the {Start} key.

D Lift the exposure glass cover.

TPEH010E

A trial print is delivered to the pa-

per delivery tray.

Note

❒ Be sure to lift the exposure glass

cover more than 30cm, 12".

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

I Press the{Proof} keyandcheck the K Press the {Print} key.

image density and the image po-

sition on the proof print.

Note

❒ To stop the machine during a

Note

multi-print run, press the

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

{Clear/Stop} key.

❒ To return the machine to the ini-

tial condition after printing,

press the {Clear Modes/Energy

Saver} key.

❒ If the image density is slightly

dark or light, adjust the image

density using the {W}{V} keys.

See p.25 “Adjusting the Image

Density of Prints”.

Removing Prints

A Pull the front paper delivery side

J Enter the number of prints re-

plate down towards you to open.

quired with the number keys.

Note

❒ You cannot open the rear paper

❒ To change the number entered,

pressthe{Clear/Stop}keyanden-

ter the new number.

delivery side plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Standard Printing

B Remove the prints from the paper

delivery tray and close the paper

delivery side plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Energy Saver Mode

If you do not operate the machine for a certain period, the display disappears

and the machine enters Energy Saver mode to reduce energy consumption.

Note

❒ You can change the time the machine waits before Energy Saver mode starts.

See “Energy Saving” on p.141 “1. System”.

❒ The machine will not automatically enter Energy Saver mode in such cases as

follows:

• If there is no ink

• If originals or paper are jammed

• If the machine is making master or printing

• If the machine is printing the second page of a combined print job

• If the machine is loading original images in memory

• If there is no paper

• If there is no master

• If the master eject unit is full

• If originals are left on the document feeder

• If the “cover open” message is displayed

• If the settings have been reset to their defaults

• If there are prints in the sorter's paper delivery tray

• If the User Code entry screen is displayed

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Reset

If you do not operate the machine for a certain period after printing, the machine

will return to the initial condition. This function is called “Auto Reset”.

Note

❒ You can change the time the machine waits before Auto Reset starts. See “Au-

to Reset” on p.141 “1. System”.

❒ The machine will not enter Auto Reset in such cases as follows:

• If there is no ink

• If originals or paper are jammed

• If the machine is making master or printing

• If the machine is printing the second page of a combined print job

• If the machine is loading original images in memory

• If there is no paper

• If there is no master

• If the master eject unit is full

• If originals are left on the document feeder

• If the “cover open” message is displayed

• If the settings have been reset to their defaults

• If you select “Off” for “Auto Reset” with the user tools

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Adjusting the Position of Printed Images

Use the following procedure to adjust

B Adjust image position using the

the position of print images as re-

{~}, {}}, {|}, and {{} keys.

quired.

GRPOSI0E

Note

* Paper feed direction

❒ When you shift the image for-

ward, leave a 10mm, 0.4" mar-

gin at the leading edge. If there

is no margin, paper might wrap

around the drum and cause a

misfeed.

Limitation

❒ For 308 mm, 12.2"-width paper,

you can only adjust the position of

the print image 5 mm, 0.2" up or

down.

❒ The {~} and {}} keys shift the

image up to 15mm, 0.6" each

way in 0.5mm, 0.02" steps.

Note

❒ When the main switch is turned

off, the position returns to the de-

fault.

❒ The {|} and {{} keys shift the

image up to 10mm, 0.4" each

way in 0.5mm, 0.02" steps.

A Press the [Image =] key.

C Press the [OK] key.

D Press the {Proof} key to check the

image position.

Note

❒ You can skip step A and adjust

the image position directly by

pressing the {~}, {}}, {|},

and {{} keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Image Density of Prints

There are two ways to adjust the im-

age density of prints:

After Making a Master

❖ Before making a master

Use the {Image Density} key.

A To increase the image density,

press the {W} key. To reduce the

image density, press the {V} key.

❖ After making a master

Use the {W}{V} (Speed) keys.

Before Making a Master

A Press the {Image Density} key to ad-

just the image density.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Note

❒ The faster the printing speed be-

comes, the lighter the printing

density is. If you want darker

prints, decrease the printing

speed.

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS010N

B Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Tint Mode

Use this function to make halftone

prints.

GRTINT0E

A Press the [Original] key.

B Select the [Tint] with the [←] [→]

or {~} {}} keys.

C Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the Printing Speed

Use the {W} or {V} key to adjust the

printing speed. The relationship be-

tween printing speed and print quali-

ty depends on the type of paper you

use.

A Press the {V} key to increase the

speed and press the {W} key to re-

duce the speed.

Note

❒ The following speeds are avail-

able:

• Setting 1:

60 sheets/minute

• Setting 2:

75 sheets/minute

• Setting 3 (default):

90 sheets/minute

• Setting 4:

105 sheets/minute

• Setting 5:

120 sheets/minute

❒ The faster the printing speed be-

comes, the lighter the printing

density is, and vice versa.

❒ When the machine is used in

low temperature conditions, the

image density might decrease.

In this case, slow the printing

speed down to setting 1 or 2.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Stopping a Multi-print Run

Stopping a Multi-print Run to

Print Another Original

Changing the Number of

Prints Entered and Checking

Completed Prints

A Press the {Clear/Stop} key.

B Set the original.

B Change the number of prints or

C Enter the number of prints and

check the completed prints.

press the {Start} key.

Note

❒ To change the number of prints,

press the {Clear/Stop} key, and

then re-enter the number of

prints with the number keys.

C Press the {Print} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Reducing and Enlarging Using Preset Ratios

Reducing and Enlarging Using Preset

Ratios

Use this function to have originals re-

duced or enlarged by a preset ratio. A

total of 7 ratios are available (3 en-

largement ratios, 4 reduction ratios).

❒ You can select a ratio regardless of

the size of an original or printing

paper. With some ratios, parts of

the image might not be printed or

margins will appear on prints.

❒ You can change the preset repro-

duction ratios with the user tools.

See “Reproduction Ratio” on p.154

“3-4 Reproduction Ratio”.

❒ Prints can be reduced or enlarged

as follows.

GRRATI0E

❖ Metric version

Ratio (%) Original → Print paper size

Note

141

122

115

A4 → A3, A5 → A4, B5 → B4

A4 → B4, A5 → B5

B4 → A3, B5 → A4

—

❒ The leading edge of the print im-

age does not shift when a print im-

age is made with this function.

A3 → B4, A4 → B5

B4 → A4, B5 → A5

A3 → A4, A4 → A5, B4 → B5

❖ Inch version

Ratio (%) Original → Print paper size

155

129

5 ¹/₂" × 8 ¹/₂" → 8 ¹/₂" × 14"

8 ¹/₂" × 11" → 11" × 17", 5

¹/₂" × 8 ¹/₂" → 8 ¹/₂" × 11"

121

8 ¹/₂" × 14" → 11" × 17"

1. Place on the exposure glass

—

2. Place in the optional document

feeder

8 ¹/₂" × 14" → 8 ¹/₂" × 11"

11" × 15" → 8 ¹/₂" × 11"

* Paper feed direction

a = 8mm, 0.32"

11" × 17" → 8 ¹/₂" × 11", 8

¹/₂" × 11" → 5 ¹/₂" × 8 ¹/₂"

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

A Press the [Ratio] key.

G Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

H Make your prints.

B Select the desired ratio with the

[←] [→] or {~} {}} keys.

C Press the [OK] key.

D Make sure that the original and

the print paper are the correct

size.

E Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

F Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Magnification

Use this function to have the machine choose an appropriate enlargement or re-

duction ratio based on the size of your original and the paper size you select.

GRAUTO0E

Note

❒ The range of ratios which the machine can select depends on where you place

the original:

• On the exposure glass: 50 – 200%

❒ The table below shows the reproduction ratios that can be selected for various

combinations of original and paper size.

❖ Metric version

Original A3L

B4L

A4L

A4K

B5L

B5K

A5L ^*2A5K ^*2

Paper

A3L

B4L

A4L

A4K

B5L

B5K

A5L

B6L

100%

87%

71%

71% ^*1

61%

61% ^*1

50%

115%

100%

82%

141%

122%

100%

163%

141%

200%

173%

100% ^*1115%

115% ^*1115%

100%

100% ^*1122%

100% ^*1100% 122% ^*1122%

115% ^*1141%

141% ^*1

82% ^*1

100% ^*1100%

141% ^*1141%

122% ^*1

71%

87%

87% ^*1

71% ^*1

50%

87% ^*1

87%

71%

71% ^*1

61% ^*1

82%

71%

82% ^*1

71% ^*1

100%

87%

100% ^*1

87% ^*1

50%

61%

The machine automatically rotates the original image by 90° to match the paper

direction and selects an appropriate reproduction ratio. See p.82 “Image Rota-

tion”.

Place these originals in the optional document feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

❖ Inch version

8¹/₂" × 14" 8¹/₂" × 11" 8¹/₂" × 11" 8¹/₂"

5¹/₂" 8¹/₂× 5¹/₂"

Original 11" × 17"

L ^*2

K ^*2

Paper

11" × 17"L 100%

121%

100%

129%

200%

155%

8¹/₂" × 14"

77%

8¹/₂" × 11"

100% ^*1

100%

129% ^*1

129%

65%

77%

100%

129%

8¹/₂" × 11" 65% ^*1

77% ^*1

61%

100% ^*1

65%

129% ^*1

100%

8¹/₂"×5¹/₂"

65% ^*1

100% ^*1

50%

The machine automatically rotates the original image by 90° to match the paper

direction and selects an appropriate reproduction ratio. See p.82 “Image Rota-

tion”.

Place these originals in the optional document feeder.

❒ Depending on the original type, a suitable reproduction ratio might not be

able to be selected. See p.13 “Originals” and see p.125 “Originals”.

A Place your original on the exposure glass or in the optional document feed-

er.

B Press the [Ratio] key.

C Select [Auto] with the [→] or {}} key.

D Press the [OK] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Magnification

E Press the {Start} key.

F Check the image position on the trial or proof print.

Note

❒ If the image position is not correct, adjust it using the [Image =] keys. See

p.24 “Adjusting the Position of Printed Images”.

G Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Zoom

Use this function to fine-tune the re-

production ratio in increments of 1%.

C Press the [OK] key.

D Make sure that [Zoom] is selected.

E Press the [OK] key.

F Select the desired reproduction

ratio in one of the following

ways:

GRZOOM0E

Note

❒ The range of ratios you can select

depends on where you place the

original:

Note

❒ To change the value entered,

press the {Clear/Stop} key and

enter the new value.

• On the exposure glass: 50–200%

A Press the [Ratio] key.

Using the [←] [→] or {~} {}}

keys

A Adjust the ratio with the [←]

[→] or {~} {}} keys.

B Select [Mag.] with the [→] or {}}

key.

Note

❒ To select a custom ratio, select

the closest ratio with the [←]

[→] or {~} {}} keys. Then

press the {|} or {{} key and go

to step F.

Download from Www.Somanuals.com. All Manuals Search And Download.

Zoom

K Check the image position on the

Using the number keys

trial or proof print.

A Enter the ratio with the num-

Note

ber keys.

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

L Make your prints.

B Press the {q} key.

G Press the [OK] key.

H Make sure that the original and

the print paper are the correct

size.

I Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

J Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Directional Magnification (%)

Use this function to choose different

D Select [Direct.Mag.(%)] with the [→]

reproduction ratios for the horizontal

and vertical directions. The result is a

squeezing or stretching effect.

or {}} key.

E Press the [OK] key.

CP2P01EE

F Enter the vertical and horizontal

ratio.

Note

❒ The range of ratios you can select

depends on where you place the

original:

• On the exposure glass: 50 –

200%

Note

❒ To change the value entered,

pressthe{Clear/Stop}keyanden-

ter the new value.

A Press the [Ratio] key.

Adjusting ratios with the [←] [→]

or {~} {}} keys

A Adjust the vertical ratio with

the [←] [→] or {~} {}} keys.

B Press the {{} key.

B Select [Mag.] with the [→] or {}}

C Adjust the horizontal ratio with

key.

the [←] [→] or {~} {}} keys.

C Press the [OK] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Directional Magnification (%)

Entering ratios with the number

keys

A Enter the vertical ratio with the

number keys.

B Press the {q} key.

C Enter the horizontal ratio with

the number keys.

D Press the {q} key.

G Press the [OK] key.

H Make sure that the original and

the print paper are the correct

size.

I Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

J Press the {Start} key.

K Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

L Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Directional Magnification (Size)

Use this function to have the machine

A Press the [Ratio] key.

select suitable reproduction ratios

based upon the dimensions of the

print you require and the size of the

original you specify.

B Select [Mag.] with the [→] or {}}

key.

CP2M01EE

1. Horizontal original size

2. Vertical original size

3. Horizontal print size

4. Vertical print size

Note

C Press the [OK] key.

❒ You can enter sizes within the fol-

lowing ranges.

D Select [Direct.Mag.(Size)] with the

Metric ver-

sion

1 - 999mm (in 1mm steps)

[→] or {}} key.

Inch version 0.1" - 99.9" (in 0.1" steps)

❒ The range of ratios which the ma-

chine can select depends on where

you place the original:

• On the exposure glass: 50-200%

❒ If the calculated ratio is over the

maximum or under the minimum

ratio, it is corrected within the

range of ratios automatically.

E Press the [OK] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Directional Magnification (Size)

F Enter the vertical original size M Press the {Start} key.

with the number keys and press

the {q} key.

Note

❒ To change the value entered,

pressthe{Clear/Stop}keyanden-

ter the new value.

N Check the image position on the

❒ Up to 999mm, 99.9" can be en-

trial or proof print.

tered.

Note

G Enter the vertical print size with

the number keys, and then press

the {q} key.

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

H Enter the horizontal original size

with the number keys, and then

press the {q} key.

O Make your prints.

I Enter the horizontal print size

with the number keys.

J Press the [OK] key.

The machine will select appropri-

ate reproduction ratios for the ver-

tical and horizontal directions.

K Make sure that the original and

the print paper are the correct

size.

L Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Erasing Center and Edge Margins

When printing from thick books, or

B Keep the exposure glass cover at

similar originals, the binding margin

at the center and the edges might ap-

pear on prints. To prevent this, per-

form the following steps.

an angle of at least 25 degrees

with the exposure glass.

C Press the {Start} key.

Important

❒ Be sure to keep the platen cover at

an angle of at least 25 degrees with

the exposure glass.

❒ If you do not press hard on the

book while it is scanned, the mar-

gin at the center might no be

erased completely.

Note

❒ If your originals have solid images

at the edges, the machine might

recognize the solid images as shad-

ows and not copy them. In this

case, use Edge Erase mode so that

only the shadows are not copied.

See p.41 “Edge Erase”.

Note

❒ Press hard on the book with

your hand while it is scanned.

D Check the image position on the

trial or proof print.

Note

A Set the book on the exposure

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

glass.

E Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Edge Erase

This function erases all four margins

of the original image.

A Press the {Edge Erase} key.

Image Density

Lighter

Stamp

On Line

❖ Using Edge Erase mode

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

GRERAS0E

ZDZS150N

❖ When not using Edge Erase mode

When printing from thick books,

or similar originals, the binding

margin at the center and the edges

might appear on prints. The ma-

chine erases these margins auto-

matically. If you do not use Edge

Erase mode using the following

kind of originals, the images to be

printed might be also erased.

B Select the size and direction of the

original with the [←] [→] or {~}

{}} keys.

C Press the [OK] key.

D Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

GRERAS1E

Note

❒ You can adjust the size of the mar-

gins with the user tools. The de-

fault is 2mm, 0.1". See p.155 “3-11

Margin Erase Area”.

E Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

F Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

G Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing onto Various Kinds of Paper

Before printing onto thick paper, thin

paper, envelopes or special kinds of

paper loaded in the paper feed tray,

you must select the paper type.

Printing onto Standard Paper

If you wish to print onto standard

(47.1 to 105g/m², 12.5 to 28 lb) paper,

perform the following steps.

Printing onto Thick Paper

A Press the [Ppr.Type] key.

If you wish to print onto thick (128 to

209.3g/m², 34 to 55.6 lb or heavier)

paper, perform the following steps.

A Press the [Ppr.Type] key.

B Make sure that [Std.] is selected.

B Select [Thick] with the [→] or {}}

key.

C Press the [OK] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

E If your envelopes do not feed in

well, lift the paper feed tray a lit-

tle, and then lower it so that it

slants up slightly.

Printing onto Envelopes

A Press the [Ppr.Type] key.

B Select [Special] with the [→] or {}}

key.

Printing onto Special Kinds of

Paper

Preparation

To use this function, you have to

[

User1] or [User2] with the user tools.

See p.158 “4-19 Type of Paper”.

C Press the [OK] key.

A Press the [Ppr.Type] key.

D Place the envelopes in the paper

feed tray as shown in the illustra-

tion.

B Select [User1] or [User2] with the

GRENVE0E

* Paper feed direction

Note

[←] [→] or {~} {}} keys.

❒ When you use envelopes, the

paper feed tray capacity is

about 150 sheets (85g/m², 22 lb)

or enough to load a stack up to

105mm, 4.1" high.

C Press the [OK] key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Printing onto Various Kinds of Paper

-To prevent paper misfeeds:

If paper misfeeds occur frequently,

even if you have selected a suitable

paper, follow the steps below.

^APress the [Select] key.

^BSelect the type of paper misfeed

and frequency with the {~}, {}},

{|}, or {{} keys.

^CPress the [OK] key.

If paper misfeeds occur frequently in

the paper exit section, even if you are

using standard or thin paper and

have selected [Std.], do the following:

^ASet the wing guide to the “Down”

position with the user tools. See

“Deflector Angle” on p.144 “4.

Mode Setting”.

If A4 – B5, 8¹/₂" × 11" thick paper is

not delivered properly to the paper

delivery tray, do the following:

^ASet the wing guide to the “Up” po-

sition with the user tools. See “De-

flector Angle” on p.144 “4. Mode

Setting”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Selecting Original Modes

Select one of the following five modes

to match your originals:

Letter/Photo Mode Printing

❖ Letter mode

Select when originals contain only

letters (no pictures).

Preparation

You can adjust the contrast of the

image.

❖ Letter/Photo mode

Select when originals contain pho-

tographs or pictures with letters.

A Press the [Original] key.

❖ Photo mode

Select when originals contain pho-

tographs or pictures with delicate

tones.

❖ Pencil mode

Select when originals are written

in pencil.

B Select [Letter/Photo] with the [→]

or {}} key.

❖ Tint mode

Select when you want to make

halftone printing.

Note

❒ You can adjust the sharpness of

text in Letter mode with the user

tools. See “Adjusting sharpness of

letters” on p.144 “4. Mode Set-

ting”.

C Press the [Contrast] key.

❒ When using Photo mode to print

originals with both text and photo-

graphs, the text will appear lighter.

To avoid this, select Letter/Photo

mode. Alternatively, use the op-

tional Make-up mode to specify

Letter mode for text areas and Pho-

to mode for photograph areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Original Modes

D Adjust the contrast with the [←]

Photo Mode Printing

[→] or {~} {}} keys.

A Press the [Original] key.

Note

❒ Use "High" to produce clear

B Select [Photo] with the [→] or {}}

prints of people's faces.

key.

❒ Use "Low" to produce clear

prints of landscapes and scen-

ery etc.

E Press the [OK] key.

F Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

G Press the {Start} key.

C Press the [OK] key.

Adjusting the photo mode contrast

H Check the image position on the

trial or proof print.

A Press the [Contrast] key.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

I Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

B Adjust the contrast with the

G Press the {Start} key.

[←][→] or {~}{}} keys.

C Press the [OK] key.

H Check the image position on the

Note

trial or proof print.

❒ Use "High" to produce clear

prints of people's faces.

Note

❒ Use "Low" to produce clear

prints of landscapes and

scenery etc.

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

D Select the dot pattern with the [←]

[→] or {~} {}} keys.

I Make your prints.

Pencil Mode Printing

Note

❒ Originals written in pencil should

be placed on the exposure glass.

A Press the [Original] key.

Note

❒ Four dot patterns are available:

• Setting 1: clearest

• Setting 2: clearer than setting 3

• Setting 3: clearer than setting 4

• Setting 4: clearer than the

standard setting

E Press the [OK] key.

F Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Original Modes

B Select [Pencil] with the [→] or {}}

key.

C Press the [OK] key.

D Place your original on the expo-

sure glass.

E Press the {Start} key.

F Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

G Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Economy Mode

When you want to save ink, select

Economy mode.

Note

❒ Prints will be lighter in this mode.

A Press the {Economy Mode} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS020N

B Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

C Press the {Start} key.

D Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

E Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Cycle

Use the {Auto Cycle} key to process

masters and make prints in a single

operation.

A If the indicator of {Auto Cycle} key

is off, press the {Auto Cycle} key.

B Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

All Class Mode

Preparation

Note

You have to store the number of

students in each class with the user

tools. See p.154 “3-5 Class Enter

No.”.

❒

When you choose All Class mode,

Job Separation mode is automati-

cally turned on. The job separator

pulls the top sheet of the each set

delivered to the paper delivery tray

to mark the end of each printed set.

The next cycle begins automatical-

ly. See p.77 “Job Separation”.

Use the {Class} key to make sets of

prints from the same original. All the

stored numbers of prints are made for

each set.

❒ You can cancel Job Separation

mode in All Class mode with the

user tools. See “Auto Separate” on

p.144 “4. Mode Setting”.

This feature is useful for teachers who

frequently make multiple print sets

for classes e.g. notes, handouts, tests

etc.

Using a standard print mode, the

teacher would have to stand by the

machine entering the number of

prints and pressing the {Print} key for

each class. However, All Class mode

allows you to store the number of stu-

dents in each class into the machine

memory beforehand with the user

tools. Whenever you need to make

print sets for all the classes, place

your original, select [ALL] and press

the {Start} key. Print sets will be made

containing the correct number of

prints for each class.

A Press the {Class} key.

B Make sure that [ALL] is selected.

C Press the [OK] key.

D Place one original on the expo-

sure glass or in the optional docu-

ment feeder.

GRCLAS2E

Download from Www.Somanuals.com. All Manuals Search And Download.

All Class Mode

E Press the {Start} key.

F Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

G Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Auto Class Mode

Preparation

Note

You have to store the number of

students in each class with the user

tools. See p.154 “3-5 Class Enter

No.”.

❒

When you set Auto Class mode,

Job Separation mode is automati-

cally turned on. The job separator

pulls the top sheet of the each set

delivered to the paper delivery tray

to mark the end of each printed set.

The next cycle begins automatical-

ly. See p.77 “Job Separation”.

Use the {Class} key to make sets of

prints from the same original. The

stored numbers of prints are made for

each set.

❒ You can cancel Job Separation

mode in Auto Class mode with the

user tools. See “Auto Separate” on

p.144 “4. Mode Setting”.

This feature is useful for teachers who

frequently make multiple print sets

for their classes, e.g. notes, handouts,

tests etc.

Using a standard print function, the

teacher would have to stand by the

machine entering the number of

prints and pressing the {Print} key for

each class. However, Auto Class

mode allows you to store the number

of students in each class into the ma-

chine memory beforehand with the

user tools. Then, whenever you need

to make print sets for several classes,

place your original, select the classes

that need prints and press the {Start}

key. Print sets will be made contain-

ing the correct number of prints for

each class.

A Press the {Class} key.

B Select[By-class]withthe[→]or{}}

key.

C Press the [OK] key.

GRCLAS2E

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Class Mode

D Select the desired classes for each

Selecting classes with the

number keys

grade.

A Enter the desired grade and

class with the number keys.

Selecting classes with the {~},

{}}, {|}, or {{} key

A Select the desired class for the

1^stgrade with the {}} key.

The number of students is dis-

played on the counter.

Note

❒ When you want to select all

❒ For example, to select grade 2

class 4, enter 24.

the classes, select [ALL].

B Press the [Select] key.

❒ When you want to select all

the classes for one grade, en-

ter the grade number fol-

lowed by 0.

Note

❒ Repeat steps A and B until

you have finished designat-

ing classes for the 1st grade.

B Press the {q} key.

❒ To cancel a class selection, se-

lect that class with the {~},

{}}, {|}, or {{} key, and

then press the [Cancel] key.

❒ When you want to select

many classes for one grade,

first select [ALL] and press the

[Select] key, and then dese-

lect the unnecessary classes

with the [Cancel] key.

Note

C Press the {{} key.

❒ To cancel a class, select that

class with the {~}, {}}, {|},

or {{} key, and then press

the [Cancel] key.

Now you can select classes for

the 2^ndgrade.

D Select the desired class for the

2^ndgrade with the {~}, {}},

{|}, or {{} key.

❒ Repeat steps A and B until

you have finished selecting

all the desired classes.

E Press the [Select] key.

Note

E Press the [OK] key.

❒ Repeat steps C to E until

you have finished designat-

ing all the desired classes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

F Place one original on the expo-

sure glass or in the optional docu-

ment feeder.

G Press the {Start} key.

H Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

I Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Class Mode with One Original

Use the {Class} key to make sets of

prints from the same original. Vari-

ous numbers of prints are made for

each set.

B Select [Manual] with the [→] or {}}

key.

C Press the [OK] key.

GRCLAS2E

D Enter the desired number of

prints for the first set with the

number keys.

Note

❒ When you set the Manual Class

mode, Job Separation mode is au-

tomatically turned on. The job sep-

arator pulls the top sheet of each

set delivered to the paper delivery

tray to mark the end of each print-

ed set. The next cycle begins auto-

matically. See p.77 “Job

Separation”.

E Press the {q} key.

❒ To stop Job Separation mode from

automatically turning on, use the

user tools. See “Auto Separate” on

p.144 “4. Mode Setting”.

A Press the {Class} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

F Enter the desired number of L Make your prints.

prints for the second set with the

number keys.

G Press the {q} key.

Note

❒ Repeat steps F and G for each

set.

❒ The maximum number of sets

that can be made is 20.

H Press the [OK] key.

I Place one original on the expo-

sure glass or in the optional docu-

ment feeder.

J Press the {Start} key.

K Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Manual Class Mode with two or More Originals

Manual Class Mode with two or More

Originals

Preparation

A Press the {Class} key.

To use this function, you have to

select “by each original” with the

“Class Manual Set” setting in the

user tools. See “Class Manual Set”

on p.144 “4. Mode Setting”.

Use the {Class} key to make sets of

prints from different originals. Vari-

ous numbers of prints are made for

each set.

B Select [Manual] with the [→] or {}}

A B

key.

C D

GRCLAS1E

Note

❒ When you set Manual Class mode,

Job Separation mode is automati-

cally turned on. The job separator

pulls the top sheet of each set de-

livered to the paper delivery tray

to mark the end of each printed set.

The next cycle begins automatical-

ly. See p.77 “Job Separation”.

C Press the [OK] key.

D Enter the desired number of

prints for the first original with

the number keys.

❒ You can suspend Job Separation

mode whenever you set the Manu-

al Class mode with the user tools.

See “Auto Separate” on p.144 “4.

Mode Setting”.

E Press the {q} key.

❒ With the optional document feed-

er, you can place several originals

and make prints of all of them at

once. See p.128 “Manual Class

Mode with Two or More Origi-

nals”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

F Enter the desired number of L Press the {Auto Cycle} key.

prints for the second original

with the number keys.

M Press the {Print} key.

G Press the {q} key.

Note

❒ Repeat steps F and G for each

original.

❒ Up to 20 classes can be set.

H Press the [OK] key.

I Place the first original face down

on the exposure glass.

N After the first set is completed,

place the second original on the

exposure glass, and then press the

{Start} key.

J Press the {Start} key.

K Check the image position on the

trial or proof print.

Note

❒ Repeat step N until you have

Note

finished printing.

❒ If the image position is not cor-

rect, adjust it using the [Image =]

keys. See p.24 “Adjusting the

Position of Printed Images”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Class Mode

Use the {Class} key to make sets of

prints from the same original. The

same numbers of prints are made for

each set.

B Select [Same-NO.] with the [→] or

{}} key.

R R R

C Press the [OK] key.

GRCLAS0E

D With the number keys, enter the

desired number of prints for each

set.

Note

❒ When you choose Class mode, Job

Separation mode is automatically

turned on. The job separator pulls

the top sheet of each set delivered

to the paper delivery tray to mark

the end of each printed set. The

next cycle begins automatically.

See p.77 “Job Separation”.

E Press the {q} key.

❒ You can suspend Job Separation

mode whenever you set the Class

mode with the user tools. See “Au-

to Separate” on p.144 “4. Mode Set-

ting”.

A Press the {Class} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

F With the number keys, enter the

number of sets you wish to make.

Note

❒ Up to 99 sets can be selected for

an original.

G Press the [OK] key.

H Place one original on the expo-

sure glass or in the optional docu-

ment feeder.

I Press the {Start} key.

J Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

K Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Combine Originals

You can combine originals in two ways:

1 2

GRCOMB2E

❖ 2 single-sided originals → 1 single-sided print with 2 images

Combine two single-sided originals onto one single-sided print with the two

images placed side-by-side.

❖ 2 single-sided originals → 1 single-sided print with 4 images

Combine two single-sided originals onto one single-sided print with each im-

age duplicated (total of four images).

Note

❒ You can also use Memory Combine mode. See p.115 “Memory Combine”.

❒ You can set the machine to cancel Combine Originals mode after finishing

your print job with the user tools. See “Cancel Comb.” on p.144 “4. Mode Set-

ting”.

❒ Any image closer than 8mm, 0.32" to the leading edge of the first original will

not be printed. Any image closer than 4mm, 0.16" to the leading edge of the

second original will also not be printed. When the image is too close to the

leading edge, use copies of the originals with the image shifted at least 8mm,

0.32" for the first original (4mm, 0.16" for the second original) from the leading

edge.

❒ You can select different image settings for the first and second original.

❒ Make sure that the paper feed side plates touch the paper lightly and that the

paper size and direction shown on the panel display match the size and direc-

tion of paper actually placed in the paper feed tray. Either case can cause the

two original images not to appear in the proper position on prints.

❒ The following tables list the combinations that can be used with the Combine

feature (2 single-sided originals → 1 single-sided print with 2 images).

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

❖ Metric version

Original Size

A4K

100%

87%

B5K

115%

100%

82%

A5K

141%

122%

100%

87%

B6K

163%

141%

115%

100%

82%

A6K

200%

173%

141%

122%

100%

Paper Size A3L

B4L

A4L

B5L

A5L

71%

61%

71%

50%

58%

71%

❖ Inch version

Original Size

8¹/₂" × 11"K

100%

5¹/₂" × 8¹/₂"K

129%

Paper Size

11" × 17"L

8¹/₂" × 14"L

8¹/₂" × 11"L

5¹/₂" × 8¹/₂"L

77%

100%

65%

100%

50%

65%

❒ The following tables list the combinations that can be used with the Combine

feature (2 single-sided originals → 1 single-sided print with 4 images).

❖ Metric version

Original Size

A3L

B4L

A4L

71%

61%

50%

B5L

82%

71%

58%

50%

A5L

100%

87%

71%

61%

50%

B6L

115%

100%

82%

A6L

141%

122%

100%

87%

Paper

Size

A3L

B4L

A4L

B5L

A5L

50%

58%

50%

71%

58%

71%

❖ Inch version

Original Size

11" × 17"L

8¹/₂" × 14"

8¹/₂" × 11"

5¹/₂" × 8¹/₂"

Paper Size

11" × 17"L

50%

65%

50%

100%

77%

50%

8¹/₂" × 14"L

8¹/₂" × 11"L

5¹/₂" × 8¹/₂"L

50%

Download from Www.Somanuals.com. All Manuals Search And Download.

Combine Originals

❒ If a suitable reproduction ratio is not selected, images might not completely

appear on prints.

❒ Originals reading from left to right.

ZDZX160E

Reference

When you use the optional document feeder with this function, see p.127

“Combine Printing”.

A Place the first original face down.

ZDCH110E

Note

❒ When you place an original sideways (K), the top should be toward the

operation panel as shown above.

B Enter the number of prints using the number keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

C Check the print paper size and the reproduction ratio.

Note

❒ To have the machine choose a suitable ratio automatically, use Auto Mag-

nification mode. See p.31 “Auto Magnification”.

D Press the {Combine} key.

E Select [Combine 2] or [Quadruple] with the [←] [→] or {~} {}} keys.

F Press the [OK] key.

G Press the {Start} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Combine Originals

H The beeper sounds after the first original has been stored. Place the second

original face down.

ZDCH110E

I Press the {Start} key.

J Check the image position on the trial or proof print.

Note

❒ If the image position is not correct, adjust it using the [Image =] key. See

p.24 “Adjusting the Position of Printed Images”.

K Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Auto Combine Mode

Preparation

B Enter the number of prints using

the number keys.

To use this function, you have to

select Auto Combine mode with

the user tools. See “Combine” on

p.144 “4. Mode Setting”.

You can have images duplicated in

two ways:

1 1

C Check the print paper size and the

reproduction ratio.

Note

GRACOM0E

❒ To have the machine choose a

suitable ratio automatically, use

Auto Magnification mode. See

p.31 “Auto Magnification”.

❖ 1 single-sided original → 1 single-sid-

ed print of 2 images

The original image is duplicated

twice on one print.

D Press the {Combine} key.

❖ 1 single-sided originals → 1 single-

sided print of 4 images

The original image is duplicated

four times on one print.

Reference

See p.63 “Combine Originals” for

details.

A Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

E Select [Repeat 2] or [Repeat 4] with

the [←] [→] or {~} {}} keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Combine Mode

F Press the [OK] key.

G Press the {Start} key.

H Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

I Make your prints.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Skip Feed Printing

You can increase the time between

printsusingthe{SkipFeed} key. Byde-

fault, when one sheet of paper is fed,

the drum rotates twice. However, you

can select the number of drum rota-

tions. This gives you a chance to re-

move prints one by one from the

paper delivery tray or insert one sheet

of paper between two prints. If you

use this function, you can also use pa-

per longer than the length limitation

of 432mm, 17.0".

C If necessary select the number of

drum rotations per sheet of paper

fed with the [←] [→] or {~} {}}

keys.

Note

❒ For every sheet of paper fed, the

drum rotates twice by default. You

can change this default setting

with the user tools. See “No. of

Skip Feed” on p.144 “4. Mode Set-

ting”.

❒ You can also select the number

of rotations with the number

keys.

❒ You can select from 2 to 9 rota-

tions.

❒ The maximum length of paper in

❒ By default, the machine asks

you to confirm the number of

rotations. You can have this step

omitted by adjusting the user

tool settings. See “No. of Skip

Feed” on p.144 “4. Mode Set-

ting”.

Skip Feed mode is 460mm, 18.1".

❒ When you use paper longer than

432mm, 17.0", prints will not be de-

livered to the paper delivery tray

properly, so lower the paper deliv-

ery end plate and take out the

prints by hand.

D Press the [OK] key.

A Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

E Press the {Start} key.

B Press the {Skip Feed} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS030N

Download from Www.Somanuals.com. All Manuals Search And Download.

Skip Feed Printing

F Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

G Make your prints.

Note

❒ After printing is completed, the

Skip Feed setting returns to the

default.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Programs

You can store up to 9 frequently used

print job settings in machine memory

and recall them for future use.

D Press the [OK] key.

Note

❒ The program numbers (1 to 9)

will be displayed in the panel

display.

Note

❒ Stored programs are not cleared

when you turn off the main switch.

❒ If a user program has been pro-

tected, that program number

will not appear in the panel dis-

play. To change a protected user

program, see p.73 “Protecting a

Program”.

❒ Stored programs cannot be delet-

ed. If you want to change a stored

program, overwrite it.

Storing a Program

❒ If all the user programs have

been protected, you cannot

store any settings. Press the

[Cancel] key.

A Make the print settings you want

to put into memory.

B Press the {Program} key.

E Select the program number you

want to store the settings in with

the [←] [→] or {~} {}} keys.

C Select [Store] with the [→] or {}}

Note

key.

❒ You can also select the program

number with the number keys.

F Press the [OK] key.

Note

❒ If this program number is al-

ready used, the machine asks

whether you wish to overwrite

it or not. Press the [Yes] or [No]

key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programs

E Press the [Select] key.

Protecting a Program

F Press the [OK] key.

If you want to prevent someone from

writing over your program, do the

following:

Removing Program Protection

A Press the {Program} key.

B Select [Protect] with the [→] or {}}

key.

C Press the [OK] key.

D Select the program number you

want to protect with the [←] [→]

or {~} {}} keys.

D Select the program number you

want to remove protection from

with the [←] [→] or {~} {}} keys.

Note

❒ Already protected program

numbers are shown with a

black background (e.g. A).

❒ Already protected program

numbers are shown with a

black background (e.g. A).

❒ You can also select the program

number with the number keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

E Press the [Select] key.

E Press the [OK] key.

F Press the [OK] key.

F Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

Recalling a Program

G Press the {Start} key.

A Press the {Program} key.

B Make sure that [Recall] is selected.

C Press the [OK] key.

Note

❒ Programs that have been stored

beforehand are represented by a

number.

D Select the program number you

want to recall with the [←] [→] or

{~} {}} keys.

Note

❒ You can also select the program

number with the number keys.

Download from Www.Somanuals.com. All Manuals Search And Download.

Security Mode

This function prevents others from

making prints of confidential docu-

ments from the master. For example,

if you want to print some documents

with sensitive information, use this

function after making your prints so

that nobody can access that master

again.

A Make your prints.

B Press the {Security} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS040N

C Press the [Yes] key.

Note

❒ If you set Security Mode, you

cannot make prints after finish-

ing one job even if you press the

{Proof} key or {Print} key. Press

the [Exit] key.

❒ You cannot cancel Security

mode even if you turn off the

main switch.

❒ Security mode is canceled when

you make a new master.

❒ You cannot pull out the drum

unit when in security mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Quality Start Mode

If the machine is not used for a long

period of time or you change the color

drum unit, the ink on the drum might

dry causing print quality to deterio-

rate. To solve this problem, you can

have the machine carry out a few idle

spins of the drum before a print run.

This will restore image quality and

save you having to make a repeat

print run.

Using Quality Start Manually

A Press the {Quality Start} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

You can use this feature in two ways:

Edge Erase

Skip Feed

Job Separator

❖ Manual Quality Start

Choose Quality Start mode for the

next print run manually using the

{Quality Start} key.

ZDZS050N

B Place your original on the expo-

sure glass or in the optional docu-

ment feeder.

❖ Auto Quality Start

Have the machine check automati-

cally how long ago it was used be- C Press the {Start} key.

fore each print run. If the machine

The drum unit idles.

has not been used for a long time,

Quality Start will be used for the

print job. By default, Auto Quality

Start mode is on. You can turn it off

with the user tools. See “Setting

Q.start” on p.144 “4. Mode Set-

ting”.

Note

❒ You can change the number of

spins in Manual Quality Start

mode with the user tools. See

D Make your prints.

“Idling for Q.start” on p.144 “4.

Mode Setting”.

❒ You can change the number of

spins after the fixed time period

has passed in Auto Quality Start

mode with the user tools. See “No.

of Q.start” on p.144 “4. Mode Set-

ting”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Job Separation

The print on the top of each print set in the paper delivery tray is pulled by the

job separator. This function is useful when you make two or more print sets.

GRJOBS0E

R CAUTION:

• While printing, do not touch the belt at the end of the paper delivery tray or

the job separator. Otherwise, an injury might occur.

Limitation

❒ In Job Separation mode, the following limitations apply.

❖ Metric version

Minimum paper size

Maximum paper weight

Paper delivery tray capacity

127.9g/m²

600 sheets (64g/m²)

Length: 210mm

Width: 128mm

❖ Inch version

Minimum paper size

Maximum paper weight

Paper delivery tray capacity

Length: 8.3"

Width: 5.1"

34 lb

600 sheets (17 lb)

Note

❒ When you use thin paper, it is not recommended to use Job Separation mode.

The job separator might tear the paper.

❒ If the job separator touches the print image, prints might be marked. In this

case, it is not recommended to use Job Separation mode.

❒ When you do not use Job Separation mode, you can select the machine con-

dition after each print set is fed out to the paper delivery tray with the user

tools. See “Auto Class” on p.144 “4. Mode Setting”.

❒ If there are less than 10 sheets of paper in the paper delivery tray, the machine

may not be able to use Job Separation mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

A Press the {Job Separator} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS060N

B Make your prints.

Note

❒ After the last page of each print set is fed out to the paper delivery tray, the

job separator pulls the last sheet of each group in Job Separation mode. The

next job separation begins.

ZDZH110E

Download from Www.Somanuals.com. All Manuals Search And Download.

Conserving the Master

The machine automatically changes

the master length depending on the

paper size you use. This saves both

master and ink.

a = Images on the master

b = Masters

c = Conserved area

Limitation

❒ The optional document feeder is

required.

Note

❒ This function is turned on when

you use A4K, 8¹/₂" × 11" K or

B5K paper and you set 2 or more

originals in the optional document

feeder.

❒ This function does not apply to the

last page.

❒ You can cancel Master Saving

mode with the user tools. See

“Master length” on p.144 “4. Mode

Setting”. You can also save master

using the optional A4, 8¹/₂" × 11"

drum. See p.134 “Changing the

Drum Size”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

On Line Printing

On Line printing allows you to use

this machine as a PC printer.

A Press the [fin PRNT] key.

Limitation

❒ The optional PC controller is re-

quired.

Note

❒ Before printing onto A5K, 5¹/₂" ×

8¹/₂" K, or non-standard size pa-

per, you need to select the paper

size with the [Pnt.Size] key.

When printing onto A5K, 5¹/₂" ×

8¹/₂" K, or non-standard paper

sizes

❒ When printing onto thick paper,

thin paper or special kinds of pa-

per from the paper feed tray, select

the paper type before pressing the

{On Line} key. See p.43 “Printing

onto Various Kinds of Paper”.

A Press the [Pnt.Size] key.

A Press the {On Line} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

B Select A5K, 5¹/₂" × 8¹/₂"K, or

Custom (non-standard) with

the [←] or [→] key.

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS070N

When a print job has not finished

printing while in online mode

If a print job has not finished print-

ing and the job is interrupted, the

machine cannot receive data from

the PC. To print the next job from

the PC, cancel the interrupted

print job.

C Press the [OK] key.

When printing onto standard

paper sizes or sizes other than

A5K, 5¹/₂" × 8¹/₂"K

A Refer to the PC controller man-

ual.

Download from Www.Somanuals.com. All Manuals Search And Download.

On Line Printing

Auto On Line

You can select whether the machine

automatically switches to On Line

mode when it receives data from a

PC.

Preparation

• The default setting for On Line

mode is On. However, you can

change the setting to Off if re-

quired.

• You can press the {Auto On Line}

key to switch Auto On Line on

or off. If the Auto On Line indi-

cator is lit, Auto On Line is ac-

tive. If the indicator is off, Auto

On Line is inactive.

• When the Auto On Line indica-

tor is lit, Auto On Line has pri-

ority when data is received

from a PC. If you want to pre-

vent the machine from inter-

rupting a print job when it

receives data from a PC, press

the {Auto On Line} key so the

Auto On Line indicator goes off

and Auto On Line becomes in-

active.

A Press the {Auto On Line} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS160N

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Image Rotation

When your original setting direction is different from the paper direction, the

machine automatically rotates the original image by 90° to match the paper di-

rection.

Note

❒ The following tables list the combinations that can be used in Image Rotation

mode.

❖ Metric version

Original A3L

B4L

A4L

A4K

B5L

B5K

A5L✩ A5K✩

Paper

A4L

A4K

B5L

B5K

A5L

B6L

#: The machine automatically rotates the original image by 90° to match the pa-

per direction.

✩: Place these originals in the optional document feeder.

❖ Inch version

Original 11" × 17"

8¹/₂" × 14" 8¹/₂" × 11" 8¹/₂" × 11" 5¹/₂" 8¹/₂" 5¹/₂" ×8¹/₂"

L✩

K✩

Paper

8¹/₂" × 11"L --

8¹/₂" × 11"K

5¹/₂" × 8¹/₂" --

#: The machine automatically rotates the original image by 90° to match the pa-

per direction.

✩: Place these originals in the optional document feeder.

Note

❒ If you use Zoom mode, non-standard size originals or paper, the image will

not be rotated.

❒ It takes longer than usual to make masters in Image Rotation mode.

❒ You can cancel Image Rotation mode with the user tools. See “Auto Rotation”

on p.144 “4. Mode Setting”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Printing Features

The optional editing function is required for this feature.

Make-up mode enables you to do more than just make an exact copy of the orig-

inal. A variety of editing and image processing functions allow you to quickly

and easily customize your prints.

Main Features

Command sheets allow you to create special effects without cutting and past-

ing—up to 4 commands can be given for an original. By combining Make-up

modes and printing with different color drums, you can create a variety of print-

ing effects.

Make-up Modes for Designated Areas

Mode

Sample

Designated Area

Command sheet/Original

(Closed area method)

Letter mode

WORLD

World computer and

peripheral devices

are equipped with

World computer and

peripheral devices

are equipped with

Photo mode

HAWAII

Please enjoy your

Summer vacation.

Please enjoy your

Summer vacation.

Delete Area mode

Outline mode

Hello!

How are you?

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Mode

Sample

Designated Area

Command sheet/Original

(Closed area method)

P./N. mode (Positive Neg-

ative mode)

BALLET

Solid mode (Image Pattern

mode)

BALLET

All Page Pattern mode

(Area Pattern mode)

LUNCH

All + Outline (Image Out-

line and Area Pattern

mode)

CAT

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Printing Features

Make-up Modes for Outside Designated Areas

Mode

Sample

Undesignated Area

Command sheet/Original

Letter mode: The area out-

side designated areas is

printed in Letter mode.

HAWAII

Please enjoy your

Summer vacation.

Please enjoy your

Summer vacation.

Photo mode: The area out-

side designated areas is

printed in Photo mode.

WORLD

World computer and

peripheral devices

are equipped with

World computer and

peripheral devices

are equipped with

Save Area mode: The area

outside the designated ar-

eas is deleted.

HAWAII

Please enjoy your

Summer vacation.

Outline mode: The area

outside the designated

area is printed in Outline

mode.

HAWAII

Note

❒ In Make-up mode, commands must be given for both designated areas and

areas outside the designated areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Background Patterns

A total of 164 background patterns is available in Make-up mode:

• 40 basic patterns

• 40 patterns similar to the basic patterns but with patterns elements at 4 times

the size.

• 80 variants based on 90° rotations of all the basic and enlarged patterns.

• 4 registered user patterns.

* Paper Feed Direction

Note

❒ The basic patterns are numbered 1 to 40.

❒ You can make your own make-up background patterns with the user tools.

See p.163 “5-11 Make/Chg. Pattern”.

Download from Www.Somanuals.com. All Manuals Search And Download.

Command Sheets for Make-Up Printing

Command sheets are fed first so that the machine can recognize the areas of the

original which are to be edited as designated areas.

Command Sheets

The command sheet is a sheet of paper designating the areas to be edited. Com-

mand sheets must be made on white or translucent paper, and should be the

same size as the original.

Do not designate areas within 5 mm, 0.2" from the top.

Note

❒ Poor quality paper (such as newsprint, recycled paper, etc.) should not be

used for command sheets because any dark spots or streaks will be read as

designated areas.

❒ Do not use blotting paper or other absorbent paper for command sheets be-

cause ink might leak through the paper and get the exposure glass dirty.

Making a Command Sheet

There are two ways of designating areas: the diagonal line method and the

closed area method.

-Features

• You can combine up to 4 command sheets when making a master.

• You cannot use both the closed and diagonal line method on the same com-

mand sheet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

• There is no limit to the number of areas you can designate on a single com-

mand sheet.

• If designated areas on two or more command sheets overlap, the last com-

mand sheet will apply to the overlapping portion.

• If you use Outline mode for letter images with a thickness of less than 3mm,

0.12", the print image might come out as expected.

-Notes

The image might differ depending on how the designated area is drawn, so re-

member the following when making the command sheet.

Designated area

Area recognized

Preferred designated area

Part of the designated area is

surrounded by 3 sides of the en-

tire area.

Make a space of at least 2mm,

0.08", in front of the area surround-

ed by 3 sides (relative to the feed

direction).

1, 2 = 2mm, 0.08"

Double line pattern.

Only the outer line is Make a gap of at least 2mm, 0.08"

recognized. in width.

Download from Www.Somanuals.com. All Manuals Search And Download.

Command Sheets for Make-Up Printing

Designated area

Area recognized

Preferred designated area

The designated area is sur-

rounded by 3 sides of another

designated area.

Make a space of at least 2mm, 0.08"

in front of the area surrounded by

3 sides (relative to the feeding di-

rection).

1, 2 = 2mm, 0.08"

Non-closed line

Designate the area with a closed

line.

Diagonal line method

Note

❒ A diagonal line must be drawn through the area that you wish to edit.

A Put the command sheet on top of the original.

ZM-20

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

B Draw a line using a felt tip pen (black, red or blue) with a thickness of at

least 1mm.

ZM-21

Note

❒ Make sure there is no break in the line.

❒ The diagonal line can be drawn from left to right or vice versa.

❒ Draw the line at least 2mm, 0.08", away from the image so that the whole

image can be recognized.

GRCOMM1E

a, b, c, d = 2mm, 0.08"

❒ The line marking the designated area should be more than 2mm, 0.08",

from any neighboring image.

GRCOMM2E

a, b, c = 2mm, 0.08"

Download from Www.Somanuals.com. All Manuals Search And Download.

Command Sheets for Make-Up Printing

Closed area method

Note

❒ The line designating the area must be a closed loop.

A Put the command sheet on top of the original.

ZM-20

B Using a black, red, or blue felt tip pen, draw a line around the area to des-

ignate. The line should have a thickness of at least 1mm.

ZM-26

Note

❒ Make sure there is no break in the line.

❒ Draw the line at least 2mm, 0.08", away from the image so that the whole

image can be recognized.

a = Line marking the designated area

b = 2mm, 0.08"

c = Image within the designated area

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

❒ The line marking the designated area should be more than 2mm, 0.08",

from any neighboring image.

GRCOMM4E

a = 2mm, 0.08"

b = Neighboring image

c = Line marking the designated area

d = Image within the designated area

Command Sheets and Finished Prints

The following illustrations will help you understand how to draw a command

sheet.

❖ Drawing a command sheet using a diagonal line

The diagonal line method is easy to use for designating rectangular areas. It is

also more precise, but it is difficult to use for designating complex areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

Command Sheets for Make-Up Printing

❖ Drawing a command sheet using a closed line

fruit

The closed line method is easier to use for complex areas, but it is less precise. It

also takes longer to draw a command sheet with the closed line method.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Make-up Printing

A Press the {Make-Up} key.

E Select the mode for the first com-

mandsheetwiththe[←][→]or{~}

{}} {|} {{} keys.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS080N

B Make sure that [1] is selected.

F Press the [OK] key.

Then press the [OK] key.

G If necessary, select the pattern for

the first command sheet with the

{~}, {}}, {|}, or {{} key. Then

press the [OK] key.

C Select the frame shape with the

H If necessary, select the size and

direction of the pattern you se-

lected in step G with the [←] [→]

or {~} {}} keys.

[←] [→] or {~} {}} keys.

D Press the [OK] key.

I Press the [OK] key.

Note

❒ Follow steps B – I for the other

command sheets.

❒ You can select a pattern regis-

tered with the user tools for

only one command sheet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Printing

❒ To change the value entered,

pressthe{Clear/Stop}keyanden-

ter the new value.

M If you have selected Photo mode,

select the dot pattern and the con-

trast with the [←] [→] or {~} {}}

keys.

J After you have finished designat-

ing modes for all the command

sheets, select [Outside Area] with

the [←] [→] or {~} {}} keys.

K Select the mode for the outside

area with the [←] [→] or {~} {}}

keys.

Note

❒ Four dot patterns settings are

available:

• Setting 1: clearest

• Setting 2: clearer than setting 3

• Setting 3: clearer than setting 4

L Press the [OK] key.

• Setting 4: clearer than the

standard setting

Note

❒ When you select Photo mode

for both inside and outside ar-

eas, you cannot select different

dot patterns and contrast.

N Press the [OK] key.

❒ When you want to confirm your

settings, press the {Make-Up} key

twice. Then press the [OK] key

repeatedly until the panel dis-

play reaches the setting you

want to confirm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

O Place the first command sheet

face down on the exposure glass

and press the {Start} key.

The beeper sounds after the com-

mand sheet is scanned.

Note

❒ Repeat step O for the other com-

mand sheets.

P Place the original face down on

the exposure glass or face up into

the document feeder and press

the {Start} key.

Note

❒ If a command sheet or original

misfeeds from the document

feeder, remove the misfed sheet

or original and reset it in the

document feeder.

❒ It is not necessary to reset the

previous command sheets or

original.

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Samples

-Sample 1

^ACommand Sheet No. 1, Frame shape , Designated area: Delete Area mode

^BOutside area: Letter mode

^CPrint

ZM-50

1. Original

2. Command sheet No.1

3. Print

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

-Sample 2

^ACommand Sheet No. 1, Frame shape/, Designated area: All + Outline No. 30

^BCommand Sheet No. 2 Frame shape , Designated area: All page pattern No.

^COutside area: Fn1

^DPrint

ZM-51

1. Original

3. Command sheet No.2

2. Command sheet No.1

4. Print

Download from Www.Somanuals.com. All Manuals Search And Download.

Make-up Samples

-Sample 3

^APrint the original as it is

^BChange the drum unit for color printing

^CCommand Sheet No. 1, Frame shape , Designated area: All page pattern

No. 39

^DOutside area: Letter mode

^EPrint

ZM-52

1. Original

2. Command sheet No.1

3. Print

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Original Storage

You can store frequently used origi-

nals in machine memory and then

easily recall them later to make prints

whenever they are needed.

A Press the {Original Storage} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Preparation

• You can store up to 8 Original

Storage settings in machine

memory.

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

• The number of Original Storage

settings you can store depends

on the type of originals.

ZDZS170N

B Select [Store] with the [→] or {}}

• You may not be able to store

Original Storage settings for

some types of original.

key.

• The machine remembers Origi-

nal Storage settings even after

the power to the machine has

been switched off or the {Clear

Modes/Energy Saver} key has

been pressed to clear.

C Press the [OK] key.

Storing Originals

D Select the desired number to store

Store the print images of the originals

you want to use frequently.

with the [←][→] or {~}{}} keys.

Note

❒ You can use this feature with:

• Reproduction Ratio

• Selecting Original Modes

• Adjusting the Image Density of

Prints

• Edge Erase

100

Download from Www.Somanuals.com. All Manuals Search And Download.

Original Storage

E Place the original on the exposure

glass as shown, then press the

{Start} key.

Non-standard size originals

A If you place non-standard size

original, this display will be

shown.

Press the [OK] key.

ZDCH110E

Note

❒ If print images for an original

have already been stored in ma-

chine memory, check the stored

images and choose whether to

overwrite them or not. To over-

write the images, press the [Yes]

key. To keep the images, press

the [No] key.

B Enter the vertical length with

the number key, and then

press the {#} key.

C Enter the horizontal width

with the number key, and then

press the {#} key.

TPES580E

D Place your originals on the ex-

posure glass, and then press

the {Start} key.

❒ If you select overwrite, the doc-

ument stored in memory will be

erased unless it is write protect-

ed.

101

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Selecting Stored Originals

Protecting Stored Originals

To select the images of originals that

have been stored in machine memo-

ry, do the following:

If you want to protect the images of

originals stored in machine memory,

do the following:

A Press the {Original Storage} key.

Protecting Originals

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

A Press the {Original Storage} key.

Make-Up

Over lay

Auto On Line

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Economy Mode

Original Storage

Make-Up

Over lay

Auto On Line

Edge Erase

Skip Feed

Job Separator

Economy Mode

Original Storage

ZDZS170N

Edge Erase

Skip Feed

Job Separator

B Select [Select] with the [←][→] or

ZDZS170N

{~}{}} keys.

B Select [Protect] with the [→] or {}}

key.

C Press the [OK] key.

D Select the number of the stored

originalwiththe[←][→]or{~}{}}

keys.

C Press the [OK] key.

D Select the number of the original

to be protected with the [←][→] or

{~}{}} keys.

E Press the [OK] key.

F Press the {Start} key.

E Press the [Select] key.

102

Download from Www.Somanuals.com. All Manuals Search And Download.

Original Storage

F Press the [OK] key.

Deleting Stored Originals

Removing Original Protection

If you want to delete the images of

originals stored in machine memory,

do the following:

A Press the {Original Storage} key.

Important

Image Density

Stamp

Lighter

On Line

❒ You cannot restore the images

once they have been deleted.

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

A Press the {Original Storage} key.

Economy Mode

Original Storage

Image Density

Stamp

Lighter

On Line

Edge Erase

Skip Feed

Job Separator

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

ZDZS170N

Economy Mode

Original Storage

B Select [Protect] with the [→] or {}}

key.

Edge Erase

Skip Feed

Job Separator

ZDZS170N

B Select [Delete] with the [→] or {}}

key.

C Press the [OK] key.

D Press the [Cancel] key.

C Select the number of the original

to be deleted with the [←][→] or

{~}{}} keys.

103

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

D Select the [Yes] or [No] key.

TPES580E

Note

❒ Press the [No] key if you do not

wish to delete the Stored Origi-

nal.

104

Download from Www.Somanuals.com. All Manuals Search And Download.

Image Overlay

The machine can merge two different

originals onto the same print paper.

❖ Storage overlay

ABCDE ABCDE ABCDE ABCDE ABCDE

Two types of merging are available:

ABCDE ABCDE ABCDE ABCDE ABCDE

❖ Overlay

ABCDE ABCDE ABCDE ABCDE ABCDE

Combines the images of originals

stored in Original Storage with the

originals placed on the machine.

GROVER0E

Two different originals are merged

onto the same print paper.

Storage Overlay

❖ Format

A Press the {Overlay} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

GROVER1E

Edge Erase

Skip Feed

Job Separator

The image of the original which is

copied first will become the back-

ground image for all copies. The

following originals will be copied

with this background.

ZDZS090N

B Select [Storage overlay] with the

[←][→] or {~}{}} keys.

❖ On Line overlay

When your machine is equipped

with the optional PC controller, an

image sent from a PC and the orig-

inal image can be merged onto the

same print paper.

105

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

C Press the [OK] key.

C Place you originals and print start

with your PC.

Note

Limitation

❒ If the one of the stored originals

already chosen, the display in

step C does not show. Skip to

step D.

❒ The optional PC controller is re-

quired to use On Line Overlay

mode.

❒ In order to get a correct print

image, the size of the original

and the PC image should be

identical.

D Press the [OK] key.

E Place your originals, and then

press the {Start} key.

Overlay Format

On Line Overlay

A Press the {Overlay} key.

A Press the {On Line} key.

Image Density

Stamp

Image Density

Stamp

Lighter

On Line

Lighter

On Line

Normal

Darker 1

Darker 2

Normal

Darker 1

Darker 2

Make-Up

Over lay

Auto On Line

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

Edge Erase

Skip Feed

Job Separator

ZDZS090N

ZDZS070N

B Select one of Image Overlay

modes with the [←] [→] or {~}

{}} keys.

B Press the {Overlay} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Make-Up

Auto On Line

Darker 2

Over lay

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS090N

C Press the [OK] key.

D Place your originals, and then

press the {Start} key.

106

Download from Www.Somanuals.com. All Manuals Search And Download.

Image Overlay

Placing originals on the exposure

glass

Placing originals in the optional

document feeder

A Place the first original on the

A Place originals in the docu-

exposure glass.

ment feeder.

ZDCH110E

ZDCH120E

B Press the {Start} key.

Note

❒ To avoid originals misfeed-

ing, fan the originals before

placing them in the docu-

ment feeder.

❒ When you select [Format] in

step B, the original for the

template should be placed

first.

B Press the {Start} key.

❒ To change the background

image in Format mode, press

the {q} key. Then place the

next original for the template

and press the {Start} key.

Note

❒ When you select [Format] in

step B, the original for the

template should be on the

top.

C Place the next original on the

exposure glass.

❒ To change the background

image in Format mode, press

the{q}key.Thensetthenext

original for the template and

press the {Start} key.

D Press the {Start} key.

Note

❒ When you select [Format] in

step B, repeat steps C and D.

107

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Date Stamp

Use this function to have the date

stamped on prints.

DateStamp Print image

direction

on the dis-

play

Preparation

Before you use this function, you

have to set the machine's internal

clock with the user tools. See p.153

“1-6 Time Setting”.

Limitation

❒ The font size of the date cannot be

changed.

❒ If you select Page Stamp and Date

Stamp together, the last stamp di-

rection selected takes priority.

Note

❒ The default format of Date Stamp

is “Month Day Year”. You can

change this setting with the user

tools. See “Date Style Set” on p.148

“5. Stamp”.

A Press the {Stamp} key.

Image Density

Stamp

Lighter

On Line

❒ You can edit the Date Stamp posi-

tion. See p.160 “5-7 Position

(Date)”.

Normal

Darker 1

Make-Up

Auto On Line

Darker 2

❒ The Date Stamp directions on the

panel display and actual print im-

ages are as follows.

Over lay

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS100N

108

Download from Www.Somanuals.com. All Manuals Search And Download.

Date Stamp

B Make sure that [Date] is selected.

G Place your original, and then

press the {Start} key.

Placing your original (K) on the

exposure glass

C Press the [OK] key.

A Place your original as shown in

the illustration.

D Select the desired position and di-

rection withthe[←][→]or{~} {}}

keys.

ZDCH110E

Placing your originals (K) in the

optional document feeder

E Press the [OK] key.

F Select the [Yes] or [No] key.

A Place your originals as shown

in the illustration.

TPES580E

Note

❒ Press the [Yes] key if you wish

to set the other Stamp functions.

ZDCH120E

Note

❒ To avoid originals misfeed-

ing, fan the originals before

placing them in the docu-

ment feeder.

109

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Page Stamp

Use this function to have page num-

bers stamped on prints.

❒ You can edit the preset page num-

bering position with the user tools.

See p.161 “5-10 Position (Page)”.

❒ [P1, P2,…, P5] is the default format.

You can change this default setting

with the user tools. See

“Type(Page)” on p.148 “5. Stamp”.

A Press the {Stamp} key.

–1 –

Image Density

Stamp

GRPAGE0E

Lighter

On Line

Normal

Darker 1

Darker 2

Three numbering formats are avail-

able:

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

• P1, P2,....., P5

• 1/5, 2/5,....., 5/5

• -1-, -2-,....., -3-

Edge Erase

Skip Feed

Job Separator

ZDZS100N

Limitation

❒ The size and font of Page Stamp

cannot be changed.

B Select [Page] with the [→] or {}}

key.

❒ If you select Page Stamp and Date

Stamp together, the last stamp di-

rection selected takes priority.

Note

❒ Check the following table for the

relationship between the Page

Stamp direction on the panel dis-

play and the actual print image.

C Press the [OK] key.

PageStamp Print image

direction

on the dis-

play

D Select the desired format with the

[←] [→] or {~} {}} keys.

P.1

1/5

–1–

GRPPOS6E

–1–

GRPPOS4E

GRPPOS7E

GRPPOS5E

110

Download from Www.Somanuals.com. All Manuals Search And Download.

Page Stamp

C Enter the first page number

E Press the [OK] key.

withthe[←][→]or{~}{}}keys.

If you selected [P1,P2] or [-1-,-2-]

A Enter the first page number

withthe[←][→]or{~}{}}keys.

Note

❒ You can also enter the page

number with the number

keys.

❒ To change the value entered,

press the {Clear/Stop} key and

enter the new value.

Note

❒ You can also enter the page

number with the number

keys.

D Press the [OK] key.

❒ To change the value entered,

press the {Clear/Stop} key and

enter the new value.

F Select the desired orientation

with the [←] [→] or {~} {}} keys.

B Press the [OK] key.

If you selected [1/5,2/5]

A Enter the last page number

withthe[←][→]or{~}{}}keys.

G Press the [OK] key.

H Select the [Yes] or [No] key.

Note

❒ You can also enter the page

number with the number

keys.

TPES580E

Note

❒ To change the value entered,

press the {Clear/Stop} key and

enter the new value.

❒ Press the [Yes] key if you wish

to set the other Stamp modes.

B Press the [OK] key.

I Place your original, and then

press the {Start} key.

111

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Placing your originals (K) on the

exposure glass

A Place the first original as

shown in the illustration.

ZDCH110E

Note

❒ Repeat step I for the other

originals.

Placing your originals (K) in the

optional document feeder

A Place your originals as shown

in the illustration.

ZDCH120E

Note

❒ The first original should be

on the top.

❒ To avoid originals misfeed-

ing, fan the originals before

placing them in the docu-

ment feeder.

112

Download from Www.Somanuals.com. All Manuals Search And Download.

Stamp

B Select [Stamp] with the [←] [→] or

{~} {}} keys.

Priority

Preliminary

Confidential

GRSTAM0E

One of the following 3 messages can

be stamped on prints.

C Press the [OK] key.

CONFIDENTIAL

PRIORITY

D Select the desired message with

the [←] [→] or {~} {}} keys.

PRELIMINARY

Limitation

❒ Only one message can be stamped

at a time.

Note

❒ You can change some Stamp set-

tings (size, density, or position)

with the user tools. See “Size”,

“Stamp Density”, “Stamp Posi-

tion” on p.148 “5. Stamp”.

E Press the [OK] key.

F Select the page to be stamped

with the [←] [→] or {~} {}} keys.

❒ The message “CONFIDENTIAL”

is selected as a default. You can

change this setting with the user

tools. See “Type” on p.148 “5.

Stamp”.

A Press the {Stamp} key.

Image Density

Stamp

Lighter

On Line

Normal

Darker 1

Darker 2

G Press the [OK] key.

Make-Up

Over lay

Auto On Line

Economy Mode

Original Storage

Edge Erase

Skip Feed

Job Separator

ZDZS100N

113

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

H Select the stamp position with the

Placing your originals (K) in the

optional document feeder

[←] [→] or {~} {}} keys.

A Place your originals as shown

in the illustration.

I Press the [OK] key.

J Select the [Yes] or [No] key.

ZDCH120E

Note

❒ To avoid originals misfeed-

ing, fan the originals before

placing them in the docu-

ment feeder.

TPES580E

Note

❒ Press the [Yes] key if you wish

to set the other Stamp modes.

K Place your original and press the

{Start} key.

Placing your original (K) on the

exposure glass (contact glass)

A Set your original as shown in

the illustration.

ZDCH110E

114

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory Combine

You can combine originals in four ways:

❖ 4 single-sided originals → 1 single-sided print of 4 images

4 one-sided pages are printed onto 1 one-sided sheet, 4 original images on one

side.

❖ 8 single-sided originals → 1 single-sided print of 8 images

8 one-sided pages are printed onto 1 one-sided sheet, 8 original images on one

side.

❖ 16 single-sided originals → 1 single-sided print of 16 images

16 one-sided pages are printed onto 1 one-sided sheet, 16 original images on

one side.

❖ Repeating an image over the entire print

1 original image is printed repeatedly.

Note

❒ A separation line between images can be printed with the user tools. See

“Comb. Sep. Line” on p.144 “4. Mode Setting”.

Combining onto a Single–sided Print

❖ 4 single-sided originals → 1 single-sided print of 4 images

GRMCOM0E

115

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

❖ 8 single-sided originals → 1 single-sided print of 8 images

GRMCOM1E

❖ 16 single-sided originals → 1 single-sided print of 16 images

10 11 12

13 14 15 16

GRMCOM2E

Limitation

❒ To use “16 one-sided originals → 1 one-sided print of 16 images” mode, the

optional document feeder is required.

❒ If the calculated ratio is under the minimum ratio, it is corrected within the

range of the ratio automatically. However, with some ratios, parts of the im-

age might not be copied.

❒ The machine cannot copy originals different in size and direction.

Note

❒ The number of originals printed (combined) can be 4, 8, or 16.

❒ In this mode, the machine selects the reproduction ratio automatically. This

reproduction ratio depends on the print paper size and the number of origi-

nals.

❒ When the original is placed at a different direction from the print paper, the

machine automatically rotates the original image by 90° to match the print pa-

per direction.

116

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory Combine

❒ You can set the machine to cancel Memory Combine mode after finishing

your print job with the user tools. See “Cancel Comb.” on p.144 “4. Mode Set-

ting”.

❒ Refer to the following table when you select the original and paper sizes.

❖ Placing originals in the optional document feeder (metric version)

Original A3L

B4L

A4KL

B5KL

A5KL

Paper

A3L

B4L

A4KL

B5KL

You can use these original and paper sizes in Combine 4, 8, 16 Originals mode.

You can use these original and paper sizes in Combine 4, 8 Originals mode.

You can use these original and paper sizes in Combine 4 Originals mode.

❖ Placing originals in the optional document feeder (inch version)

Original 11" × 17"L

8¹/₂" × 14"L

8¹/₂" × 11"KL

8¹/₂" × 5¹/₂"KL

Paper

11" × 17"L

8¹/₂" × 14"L

8¹/₂" × 11"KL

5¹/₂" × 8¹/₂" L

You can use these original and paper sizes in Combine 4, 8, 16 Originals mode.

You can use these original and paper sizes in Combine 4, 8 Originals mode.

You can use these original and paper sizes in Combine 4 Originals mode.

❖ Placing originals on the exposure glass (metric version)

Original A3L

B4L

A4KL

B5KL

Paper

A3L

B4L

A4KL

B5KL

You can use these original and paper sizes in Combine 4, 8 Originals mode.

You can use these original and paper sizes in Combine 4 Originals mode.

117

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

❖ Placing originals on the exposure glass (inch version)

Original 11" × 17"L

8¹/₂" × 14"L

8¹/₂" × 11"KL

Paper

11" × 17"L

8¹/₂" × 14"L

8¹/₂" × 11"KL

5¹/₂" × 8¹/₂" L

You can use these original and paper sizes in Combine 4, 8 Originals mode.

You can use these original and paper sizes in Combine 4 Originals mode.

A Press the {Combine} key.

B Select [Memory Combine] with the [→] or {}} key.

C Press the [OK] key.

D Select your desired mode.

E Press the [OK] key.

118

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory Combine

F Place your originals.

Placing your original (K) on the exposure glass

A Place your original as shown in the illustration.

ZDCH110E

Placing your originals (K) in the optional document feeder

A Place your originals as shown in the illustration.

ZDCH120E

Note

❒ The first original should be on the top.

❒ To avoid originals misfeeding, fan the originals before placing them in

the document feeder.

119

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

G Press the {Start} key.

Note

❒ Even if the number of originals is less than the number required in the se-

lected mode, prints can be made as shown in the illustration. In this case,

press the {q} key after all the originals have been scanned.

GRMCOM3E

❒ When placing an original on the exposure glass or one sheet at a time in the

optional document feeder, repeat steps F and G. After placing the last orig-

inal, press the {q} key, and then the {Start} key.

Repeat

GRREPE0E

Limitation

❒ Part of the repeated image might not be printed depending on the paper size,

direction and reproduction ratio.

Note

❒ The number of repeated images depends on the original and paper size, and

reproduction ratio.

120

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory Combine

❒ Check the following table for the relationship between the direction of the

original and paper, and the number of repeated images.

❖ Example: copying A4 L originals onto A3L paper.

The number of repeated im- Reproduction ratio

ages

Print image

71%

GRREPE3E

❖ Example: copying A5L originals placed in the optional document feeder onto

A3L paper.

Number of repeated images Reproduction ratio

16 50%

Print image

GRREPE4E

❖ Example: copying 8¹/₂" × 11" K originals onto 11" × 17" L paper.

Number of repeated images Reproduction ratio

100%

Print image

GRREPE5E

❖ Example: copying A5L originals placed in the optional document feeder onto

A4K paper.

Number of repeated images Reproduction ratio

50%

Print image

GRREPE6E

121

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

A Press the {Combine} key.

B Select [Memory Combine] with the [→] or {}} key.

C Press the [OK] key.

D Select [Repeat] with the [→] or {}} key.

E Press the [OK] key.

F Select the reproduction ratio.

Reference

See p.29 “Reducing and Enlarging Using Preset Ratios”.

G Set your original.

122

Download from Www.Somanuals.com. All Manuals Search And Download.

Memory Combine

Placing your original (K) on the exposure glass

A Place your original as shown in the illustration.

ZDCH110E

Placing your originals (K) in the optional document feeder

A Place your originals as shown in the illustration.

ZDCH120E

Note

❒ To avoid originals misfeeding, fan the originals before placing them in

the document feeder.

H Press the {Start} key.

123

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

124

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Optional Functions

Optional Document Feeder

Insert a stack of originals in the docu-

ment feeder. It will be fed automati-

cally.

The following original sizes placed in

the document feeder can be detected.

Metric version

A3 L, B4 L, A4 KL,

B5 KL, A5KL

11" × 17" L, 8¹/₂" × 14"

L, 8¹/₂" × 11"KL, 5¹/₂"

× 8¹/₂"KL

Inch version

Originals

Placing the following originals in the

document feeder might cause mis-

feeds or damage to the originals.

Reference

Place the following kinds of originals

on the exposure glass:

• Originals heavier than 128g/m², 34 lb

For the original sizes placed on the

exposure glass can be detected, see

p.13 “Originals”.

• Originals lighter than 52g/m², 14 lb

Note

• Originals smaller than 148mm ×

❒ Place originals after correction flu-

id and ink have completely dried.

Not taking this precaution could

mark the exposure glass and cause

marks to be printed.

210mm, 5.9" × 8.3"

• Originals larger than 297mm ×

864mm, 11.6" × 34.0"

• Stapled or clipped originals

For standard printing functions, set

originals as shown below.

• Perforated or torn originals

• Curled, folded, or creased origi-

nals

• Originals with any kind of coating,

such as thermal fax paper, art pa-

per, aluminum foil, carbon paper,

or conductive paper

• Bound originals such as books

• Damaged originals

GRSETT1E

• Originals with glue on them

• Pasted originals

If the original is placed in a different

direction from the print paper, the

machine automatically rotates the

original image by 90° to match the

print paper direction.

• Originals written in pencil

• Thin originals that are a little stiff

• Originals with index tabs

You cannot place originals of differ-

ent sizes at the same time.

• Transparent originals such as OHP

transparencies or translucent pa-

per

125

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Functions

When you use thin originals, place

one original at a time in the document

feeder or place them on the exposure

glass.

Note

❒ To avoid jamming, fan the orig-

inals before placing them in the

document feeder.

The first 8mm, 0.32", of the leading

edge and the last 2mm, 0.08" of the

trailing edge cannot be printed. Make

sure the leading edge margin is at

least 8mm, 0.32", and the trailing edge

margin is at least 2mm, 0.08".

❒ The guides must fit snugly

against both sides of the stack.

C Adjust print settings as necessary,

and then press the {Start} key.

Do not stack originals above the limit

mark.

Placing Originals

A Adjust the guide to the original

size.

B Insert the aligned originals face

D Make your prints.

up into the document feeder.

ZDCH120E

Note

❒ If the next original has been

placed in the document feeder

before the machine stops, that

original is fed automatically

and a trial print is delivered to

the paper delivery tray after the

print of the first original is com-

pleted. Check the image posi-

tion on the trial print of the next

original. If necessary, make

proof prints using the {Proof}

key to check the image position

again.

❒ To avoid originals misfeeding,

fan the originals before placing

them in the document feeder.

Limitation

❒ Approximately 50 originals

(80g/m², 21 lb) can be inserted

at one time in the document

feeder. The first (top) original

will be fed first.

126

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Document Feeder

D Press the {Combine} key.

Combine Printing

Reference

See p.63 “Combine Originals” for

details.

A Insert the two originals face up.

E Select [Combine 2] or [Quadruple]

with the [←][→] or {~} {}} keys.

ZDCH120E

Note

❒ The first original will be printed

on the left side of the paper.

❒ To avoid originals misfeeding,

fan the originals before placing

them in the document feeder.

F Press the [OK] key.

G Press the {Start} key.

B Enter the number of prints with

the number keys.

H Check the image position on the

trial or proof print.

C Check the print paper size and the

Note

reproduction ratio.

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

Note

❒ To have the machine choose a

suitable ratio automatically, use

Auto Magnification mode. See

p.31 “Auto Magnification”.

❒ After the first original has been

stored, the second original is

fed.

127

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Functions

❒ If you place only one original,

the beeper sounds after the first

original has been scanned in.

Place the second original and

any print settings you require.

Then press the {Start} key.

E Press the {q} key.

Manual Class Mode with Two

or More Originals

Reference

See p.59 “Manual Class Mode with

two or More Originals”.

F Enter the desired number of

prints for the second original

with the number keys.

A Press the {Class} key.

G Press the {q} key.

B Select [Manual] with the [→] or {}}

Note

key.

❒ Repeat steps F and G for each

original.

❒ Up to 20 classes can be set.

H Press the [OK] key.

I Place your originals face up in the

document feeder.

C Press the [OK] key.

D Enter the desired number of

prints for the first original with

the number keys.

ZDCH120E

128

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Document Feeder

Note

M Press the {Print} key.

❒ To avoid originals misfeeding,

fan the originals before placing

them in the document feeder.

❒ The originals are fed from the

top of the stack. Make sure that

the originals are placed in the

correct sequence with the first

on the top.

J Press the {Start} key.

K Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

L Press the {Auto Cycle} key.

Note

❒ In Auto Cycle mode, printing

starts automatically after a trial

print is delivered.

129

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Functions

Color Printing Using the Optional Color

Drum

Color drum units are available as op-

tions in addition to the standard black

unit. For making color prints, a sepa-

rate drum unit is necessary for each

color.

Changing the Color Drum Unit

A Open the front door.

B Lower the drum unit lock lever

Note

(B1).

❒ If the ink on the color drum dries,

use the Quality Start mode. See

p.76 “Quality Start Mode”.

Making Color Prints

A Make sure that the color drum in-

dicator is lit.

Note

❒ Make sure the green light be-

side the drum unit lock lever is

on before sliding out the drum.

If the light is off, close the front

door, wait for five seconds, and

then open.

B Press the {Start} key.

C Check the image position on the

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the [Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

D Make your prints.

130

Download from Www.Somanuals.com. All Manuals Search And Download.

Color Printing Using the Optional Color Drum

C Pull the drum unit handle out F Insert the color drum unit along

slowly (B2).

the guide rail.

TPEH290E

G Lower the drum unit lock lever

D Lift the upper drum stay (B3) a lit-

tle to unlock the drum unit, and

then pull out the drum unit while

holding the drum unit handle

(B2) and the upper drum stay (B3).

(B1) of the inserted drum.

H Slide in the drum unit until it

locks in position.

Important

❒ Be careful not to let the drum

unit fall.

E Make sure the optional color

drum lock is securely set.

TPEH091E

131

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Functions

I Lift drum unit lock lever (B1).

A Prepare the two originals. Place

the first original on the exposure

glass.

TPEH081E

J Close the front door.

ZDCH110E

Note

B Enter the number of prints with

❒ Make sure that the Open Cov-

er/Unit indicator turns off, and

the Color Drum indicator turns

on.

the number keys.

Printing in Two Colors

After printing in one color, you can

print in another color on the same

side of the print.

C Press the {Start} key.

GRCOLO0E

Note

❒ Let the ink on the prints dry for a

while before printing on them

again.

D Check the image position on the

❒ If the prints are not dry, the paper

feed roller might become dirty. In

this case, wipe the roller with a

cloth.

trial or proof print.

Note

❒ If the image position is not cor-

rect, adjust it using the[Image =]

key. See p.24 “Adjusting the Po-

sition of Printed Images”.

❒ You cannot print in two colors at

one time.

132

Download from Www.Somanuals.com. All Manuals Search And Download.

Color Printing Using the Optional Color Drum

E Press the {Print} key.

F Remove the prints from the paper

delivery tray and place them on

the paper feed tray again as

shown in the illustration.

G Change the drum unit. See p.130

“Changing the Color Drum Unit”.

TPEH101E

H Place the second original and

press the {Start} key.

I Check the image position.

J Press the {Print} key.

133

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Functions

Changing the Drum Size

To save costs on master rolls and ink,

you can shorten the length of each

master by changing to an optional

smaller drum.

Printing Area (At 23°C/73°F,

65% RH)

❖ Metric version

A3 drum

More than 290 × 410mm,

11.4" × 16.2"

A4 drum

More than 290 × 200mm

❖ Inch version

11" × 17"

drum

More than 290 × 420mm,

11.4" × 16.6"

8¹/₂" × 11"

drum

More than 11.4" × 7.8"

Master Cut Length

A3 drum…320mm × 530mm, 12.5" ×

20.9", 255 masters/roll

11" × 17" drum…320 × 540mm, 12.5" ×

21.3", 245 masters/roll

Optional A4, 8¹/₂"

11"

drum…320mm × 325mm, 12.5" ×

12.8", 410 masters/roll

Note

❒ For changing the drum unit, see

p.130 “Changing the Color Drum

Unit”.

134

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Combination Chart

Combination Chart

This combination chart shows which modes can be used together.

✩

means that these modes can be used together.

means that these modes cannot be used together.

means that these modes cannot be used together (the function chosen sec-

ond takes priority).

means that these modes cannot be used together (the function chosen first

takes priority).

Function chosen second

Letter, Pho- -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * ✩ *

to, Let-

1 1

ter/Photo,

Pencil, Tint

mode

Economy

mode

✩ -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩

Auto Cycle

✩ ✩ -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩

Preset Re-

duce/En-

large

✩ ✩ ✩ -- * * * * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ *

1 1 1 1

Zoom

✩ ✩ ✩ * -- * * * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ *

1 1 1

Auto Magni- ✩ ✩ ✩ * * -- * * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ * ✩ *

fication Selec-

tion

1 1

135

Download from Www.Somanuals.com. All Manuals Search And Download.

Combination Chart

Function chosen second

Directional

Magnifica-

tion (%)

✩ ✩ ✩ * * * -- * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ *

1 1 1

Directional

Magnifica-

tion (size)

✩ ✩ ✩ * * * * -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ *

1 1 1 1

Combine

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ -- * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * ✩ * ✩ *

1 1 1 1 2 2 2 2 2 2 1

Originals (2

Images on

one sheet)

Combine

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * -- * * * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * ✩ * ✩ *

1 1 1 2 2 2 2 2 2 1

Originals (4

Images on

one sheet)

Memory

Combine

mode (4 Orig-

inals)

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * -- * * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * * * ✩ *

1 1 1 1 2 2 2 2 2 2 1 2 2

Memory

Combine

mode (8 Orig-

inals)

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * -- * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * * * ✩ *

1 1 1 2 2 2 2 2 2 1 2 2

Memory

Combine

mode (16

Originals)

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * -- ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * * * ✩ *

1 1 1 1 2 2 2 2 2 2 1 2 2

Edge Erase

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * ✩ *

All Class

mode

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ -- * * * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ *

1 1 1

Manual Class ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * -- * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ *

mode 1 1

136

Download from Www.Somanuals.com. All Manuals Search And Download.

Combination Chart

Function chosen second

Class mode ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * -- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ *

1 1 1

Job Separa- ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ -- ✩ ✩ * ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩

tion

Overlay

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ -- * * * * * * * * ✩ *

2 2 2 2 2

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * -- -- * * * * * * ✩ *

2 2 2 2 2 2 2 2 2 2 2

Storage Over- ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * -- ✩ ✩ ✩ * * * * ✩ *

lay 2 2 2 2 2 1 1 2 2 2 2

Date Stamp ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * ✩ -- ✩ ✩ * ✩ * ✩ *

2 2 2 2 2 2 2

Page Stamp ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * ✩ ✩ -- ✩ * ✩ * ✩ *

2 2 2 2 2 2 2

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * * ✩ ✩ -- * ✩ * ✩ *

2 2 2 2 2 2 2 2

✩ ✩ ✩ ✩ ✩ * ✩ ✩ * * * * * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * -- * * ✩ *

1 1 1 1 1 2 2 2 2 2 2 2 2

* ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ * * * ✩ ✩ ✩ ✩ ✩ ✩ * * * * * * * -- -- ✩ *

2 2 2 1 1 2 2 2 2 2

Original Stor- * ✩ ✩ * * * * * * * * * * ✩ ✩ ✩ ✩ ✩ * * * ✩ * * * * -- ✩ ✩ *

1 1 2 2 2 2 2 2

Form

Stamp

Repeat

Make-up

age

2 2 2 2 2 2 2 2 2 2

2 2 2

2 2 2 2

Skip Feed

On Line

✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ -- ✩

* ✩ ✩ * * * * * * * * * * * * * * * ✩ * * * * * * * * * ✩ --

2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

2 2 2 2 2 2 2 2 2

Image Rota- ✩ ✩ ✩ ✩ X ✩ X X X X ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ X X X X X X X X X ✩ X

tion

137

Download from Www.Somanuals.com. All Manuals Search And Download.

Combination Chart

138

Download from Www.Somanuals.com. All Manuals Search And Download.

4. User Tools

Accessing the User Tools

The user tools allow you to customize

various default settings. This section

is intended for the machine adminis-

trator.

Note

❒ [Next]: Press to go to the next

page.

❒ [Prev.]: Press to go back to the

A Press the {User Tools} key.

previous page.

B Press the [OK] key.

C Search for the desired user tool

number of each function with

the {~}, {}}, {|}, or {{} key.

Image Density

Lighter

Stamp

D Press the [OK] key.

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

Using the number keys

ZDZS110N

A Enter the desired user tool

number (1 to 7) with the num-

ber keys.

B Select the desired user tools

menu. See p.141 “User Tools

Menu”.

Using the {~}, {}}, {|}, or {{}

key

A Search for the desired user tool

number (1 to 7) with the {~},

{}}, {|}, or {{} key.

B Press the [OK] or {q} key.

C Enter the desired user tool

number of each function with

the number keys.

D Press the [OK] or {q} key.

139

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

C Change the settings by following

the instructions on the panel dis-

play, and then press the [OK] key.

Note

❒ To change the value entered,

press the {Clear/Stop} key before

pressing the [OK] key. Then en-

ter the new value.

❒ [Cancel]: Press to return to the

previous menu without chang-

ing any data.

D Press the {User Tools} key to return

to the standby display.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

Note

❒ The settings are not canceled

even if the main switch is

turned off or the {Clear Modes/En-

ergy Saver} key is pressed.

❒ You can also return to the stand-

by display by pressing the [Can-

cel] key.

140

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

Reference

For accessing the user tools, see p.139 “Accessing the User Tools”.

1. System

No.

Mode

Description

Auto Reset

The machine returns to its initial condition automatically after

your job is finished. The automatic reset time can be set from 1 to

5 minutes or off (0 minutes).

Note

❒ Default: Off

R. Cntr. Display

Use to display the total number of masters and prints.

Note

❒ A trial print delivered to the paper delivery tray after press-

ing the {Start} key will not be counted.

Reset R. Counter Choose whether the total number of masters and prints is reset.

Note

❒ Default: Not clear

mm/inch

Choose the units of measurement shown on the panel display.

Note

❒ Default:

•

Metric version: mm

Inch version: inch

Language on LCD The language used for panel display messages can be selected.

Note

❒ Default: English

Time Setting

Use to set the machine's internal clock.

Note

❒ The clock must be adjusted if you change the clock to daylight

saving time/summer time, or return to standard time.

Reference

For setting the clock, see p.153 “1-6 Time Setting”.

141

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

No.

Mode

Description

Data Print

Use to print out the following data.

Note

❒ Available settings:

•

Log Data (Number of prints made, how many times paper

misfeeds occur and so on.)

Reset Counters (Number of prints and master made under

each user code.)

Store Class (Registered number of students in each class.)

Energy Saving

You can set the time until the Energy Saver mode starts.

Note

❒ Default: 3 Min. (minutes)

2. Set Operat'n Mode

No.

Mode

Description

Min. Quantity

The minimum print quantity can be set between 0 and 9999.

Example: If you specify 20 as the minimum number of prints, runs

of 20 or more prints will be accepted, print runs of less than 20

prints will not be accepted.

Note

❒ Default: 0

Max. Quantity

The maximum print quantity can be set between 0 and 9999.

Note

❒ Default: 9999

CopyCount Dis- The counter can be set to show the number of prints made (Up),

play

or the number of prints left to be made (Down).

Note

❒ Default: Down

Panel Beeper

Turns the beeper on or off.

Note

❒ Default: STD. (standard)

❒ Available settings:

•

ALL OFF (The beeper does not sound when you press keys

or when warning messages appear on the panel display.)

STD. (When you press a key, the beeper does not sound.

When warning messages appear on the panel display, the

beeper sounds.)

•

ALL ON (The beeper sounds when you press a key or

when warning messages appear on the panel display.)

LCD Contrast

You can adjust the brightness of the panel display.

142

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

3. Initial Setting

No.

Mode

Description

Paper Type

Specifies the paper type at power on.

Note

❒ Default: Std. (Standard)

MSTR Makg.

Density

Specifies the image density at power on.

Note

❒ Default: Std. (Standard)

Original Priority Specifies the original mode at power on.

Note

❒ Default: Letter

Reproduct'n Ra- Adjust a fixed reproduction ratio between 50 and 200%.

tio

Note

❒ Default:

•

Metric version: 71%, 82%, 87%, 93%, 100%, 115%, 122%,

141%

Inch version: 65%, 74%, 77%, 93%, 100%, 121%, 129%,

155%

Reference

For setting the ratios, see p.154 “3-4 Reproduction Ratio”.

Class Enter No.

Before using All Class or Auto Class mode, register the number

of students in each class with this function.

Note

❒ You can store student numbers for up to 9 grades with 12

classes in each, giving a maximum of 108 classes. Each class

can have up to 9999 students.

Reference

For registering the number of students, see p.154 “3-5 Class

Enter No.”.

LT/Photo Con-

trast

Specifies the contrast level for Letter/Photo when the power is

switched on or after mode settings are cleared.

Note

❒ Default: Standard

LT/Photo Priori- Specifies the screen image in Letter/Photo mode when you press

the [Original] key.

Note

❒ Default: Letter

143

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

No.

Mode

Description

Photo Contrast

Specifies the contrast level for Photo when the power is switched

on or after mode settings are cleared.

Note

❒ Default: Standard

Photo(Screen)

Specifies the screen image in Photo mode when you press the

[Original] key.

Note

❒ Default: Standard

Eco.Mode

ON/OFF

Specifies whether Economy Mode is set to “On” or “Off” when

the power is switched on or after mode settings are cleared.

Note

❒ Default: Off

Margin Eras.Area Adjusts the erase edges margin.

Note

❒ Default: 2 mm, 0.1"

Ratio Priority

You can set the primary ratio on the display when you press the

[Ratio] key.

4. Mode Setting

No.

Mode

Description

Auto Cycle

ON/OFF

Specifies whether Auto Cycle mode is selected at power on.

Note

❒ Default: ON

Class Manual Set Use one original or multiple originals in Manual Class mode.

Note

❒ Default: Std. (One original)

Ignore Paper Size If you are making prints on non-standard paper and the original

image does not entirely appear on the print, set paper size detec-

tion to “Ignore”. The machine will not detect the paper length.

Note

❒ Default: Not to ignore

No Orig. Size DF When you set long originals in the optional document feeder, set

original detection to “Ignore”. The machine will not detect the

original size.

Note

❒ Default: Not to ignore

144

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

No.

Mode

Description

No Orig. Size

When you place originals of non standard sizes on the exposure

glass, set original detection to “Ignore”. The machine will not de-

tect the original size.

Note

❒ Default: Not to ignore

Background

ON/OFF

When you make prints in Photo, Letter/Photo, or Tint mode, the

background of the prints might become dirty. Turn Background

“On” to improve the clarity of your prints.

Note

❒ Default: W/O back. correction (off)

Longer Paper

Combine

Use paper longer than 432mm, 17.0".

Note

❒ Default: Not to use

If you select “Automatic (Auto Combine mode)”, you can make

two or four identical images on one sheet by pressing the {Com-

bine} key and {Start} key.

Note

❒ Default: Normal (Combine Originals mode)

Reference

For using Auto Combine mode, see p.68 “Auto Combine

Mode”.

Comb. Sep. Line You can select a separation line in Memory Combine mode.

Note

❒ Default: None

❒ Available settings:

GRLINE0E

•

a = None

b = Solid

c = Broken1

d = Broken2

e = CropMarks

145

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

No.

Mode

Description

Cancel Comb.

Specifies whether Combine Originals or Memory Combine mode

is cleared after finishing your print job.

Note

❒ Default: Not to cancel

No. of Skip Feed Specifies the number of drum rotations in Skip Feed mode at

power on. You can also select whether you can change the num-

ber of drum rotations temporarily when you press the {Skip Feed}

key. See p.70 “Skip Feed Printing”.

Note

❒ Default:

•

Panel display: Display

Number of Skip Feed: 2

Reference

For changing the number of rotations, see p.156 “4-11 No. of

Skip Feed”.

Idling for Q.start When you use the Manual Quality Start mode, you can select

how many times the drum unit idles.

Note

❒ Default: 7

Setting Q.start

If the machine is not used for a long period of time, the ink on the

drum might dry causing image quality to deteriorate. The Auto

Quality Start mode automatically recovers image density quality

after a selected time has passed. If Auto Quality Start mode is set

to “Not to use”, you can regain print quality by making a few ex-

tra prints or you can use the Manual Quality Start mode.

Note

❒ Default: Yes

No. of Q.start

You can select how many times the drum unit idles after the dis-

played time periods have passed in Auto Quality Start mode.

Note

❒ Default: See p.157 “4-14 No. of Q.start”.

❒ To increase the print image density, increase the number of

drum rotations, and vice versa.

Reference

For changing the number of idle spins, see p.157 “4-14 No. of

Q.start”.

146

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

No.

Mode

Description

Deflector Angle

You can change the angle of the wing guide depending on the pa-

per type you use.

Note

❒ Default: Auto

❒ Available settings:

•

Up (Select this setting when standard thickness or thin pa-

per misfeeds at the paper exit section occur frequently.)

Down (Select this setting when A4 – B5, 8¹/₂" × 11" thick

paper is not delivered properly to the paper delivery tray.)

Auto Class

When you do not use the Separation mode, you can select the ma-

chine's condition after each printing set is fed out to the paper de-

livery tray.

Note

❒ Default: Stop

❒ Available settings:

•

Start printing automatically (After the last page of each

printing set is fed out to the paper delivery tray, the ma-

chine stops for a few seconds. Then, the next cycle begins.)

Stop (After the last page of each printing set is fed out to

the paper delivery tray, the machine stops. If you press the

{Print} key, the next cycle begins.)

Auto Separate

Specifies whether Job Separation mode is automatically carried

out when you make prints in All Class, Auto Class, Manual Class,

or Class mode.

Note

❒ Default: ON

Ink/Master Left

Specifies whether you can check the amount of ink and master.

Note

❒ Default: OFF

❒ Available settings:

•

OFF (You cannot check the remaining amount of ink or

master.)

ON (When the remaining amount of ink or master is less

than half, the panel display indicates these amounts when

you turn on the main switch.)

•

Check remaining volume (You can see the remaining

amounts of ink and master regardless of these amounts.)

Type of Paper

When one kind of paper misfeed occur frequently, you can regis-

ter its paper type in “User1” or “User2”.

Reference

For registering a special paper type, see p.158 “4-19 Type of

Paper”.

147

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

No.

Mode

Description

Auto Rotation

When the direction in which your original is placed differs from

that of the paper, the machine automatically rotates the original

image by 90° to match the paper direction. You can cancel this

setting.

Note

❒ Default: ON

Master length

The machine determines the master length according to the num-

ber of originals placed in the optional document feeder and the

paper sizes. If you wish to use A3/11" × 17" master regardless of

the number of originals set and the paper sizes, select “A3”.

Note

❒ Default: Auto

Cancel Stor.O.lay Specifies whether settings for Storage Overlay are retained, or

not, when a storage overlay job has finished.

Note

❒ Default: Not to cancel

5. Stamp

No.

Mode

Description

Type

You can select the stamp message at power on with the Stamp

mode.

Note

❒ Default: CONFIDENTIAL

Size

You can edit the preset stamp sizes.

Note

❒ Default: Standard

❒ Adjustment values:

•

Double size

Stamp Density

Stamp Position

You can select the style of the stamps.

Note

❒ Default: Solid-fill

You can edit the preset stamp position.

Note

❒ Default: See p.159 “5-4 Stamp Position”.

❒ Available settings: See p.159 “5-4 Stamp Position”.

Reference

For adjusting the stamp position, see p.159 “5-4 Stamp Posi-

tion”.

148

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

No.

Mode

Description

Date Style Set

You can select the format of the date stamp.

Note

❒ Default: Month Day Year

Date Position Set You can select the date stamp direction at power on in Date Stamp

mode.

Note

❒ Default: Upper Left

Position(Date)

You can edit the date stamp position.

Note

❒ Default: See p.160 “5-7 Position (Date)”.

❒ Available settings: See p.160 “5-7 Position (Date)”.

Reference

For adjusting the date stamp position, see p.160 “5-7 Position

(Date)”.

Type(Page)

You can select the page numbering style at power on in Page

Stamp mode.

Note

❒ Default: P1,P2

Direction(Page)

You can select the page numbering direction at power on in Page

Stamp mode.

Note

❒ Default:

•

When you select “P1,P2” or “1/5,2/5” with the

“Type(Page)” user tool: Upper Right

When you select “-1-,-2-” with the “Type(Page)” user tool:

Down Center

Position(Page)

You can edit the page numbering position.

Note

❒ Default: See p.161 “5-10 Position (Page)”.

❒ Available settings: See p.161 “5-10 Position (Page)”.

Reference

For adjusting the page numbering position, see p.161 “5-10 Po-

sition (Page)”.

Make/Chg. Pat- Make your own background pattern in Make-up mode.

tern

Note

❒ You can edit the 40 preset patterns.

Reference

For changing the background pattern, see p.163 “5-11

Make/Chg. Pattern”.

149

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

6. Administrator Mode

❖ User Codes

If user codes are turned on, operators must enter their user codes before they can operate

the machine. The machine keeps count of the number of copies made under each user code.

Turn this function on with the “Set User Code(s)” user tool. You can also turn on Key Op-

erator Code mode so that only the key operator (administrator) can use the functions below.

Check Counter

Reset Counters

You can check the number of masters and copies made under

each user code.

Reference

For checking the number of masters and copies, see p.164

“6-1 Check Counter”.

You can clear each or all user code counters.

Note

❒ Default: Single

Reference

For clearing the number of masters and copies, see p.164 “6-

2 Reset Counters”.

Set User Code

Selects User Code mode. For details about User Code mode, see

p.150 “6. Administrator Mode” Use Code(s).

Enter the key Operator Code if you have already set it. See

p.150 “6. Administrator Mode”.

Note

❒ Default: Not to use

Reg. User Code

Chg. User Code

You can register user codes.

Note

❒ Up to 20 user codes (up to 4 digits) can be registered.

You can change user codes.

Note

❒ The number of copies made under the old code is added to

that made under the new user code.

Reference

For changing the user codes, see p.165 “6-5 Chg. User

Code”.

150

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools Menu

Del. User Code

You can delete user codes.

Note

❒ The number of copies made under the deleted code is also

deleted.

Reference

For deleting user codes, see p.166 “6-6 Del. User Code”.

Key Operator Code Use to turn Key Operator Code mode on or off.

Note

❒ Default: Not to use

Reg/Chg Key-

OpCode

You can register or change key operator codes. (up to 4 digits)

Restrict. Access

In Key Counter mode, you have to set the key counter before

making prints. (To turn on Key Counter mode, contact your

service representative.) If Key Counter mode is on, Restricted

Access is turned on (“To use”) automatically. If you turn Re-

stricted Access off (“Not to use”), you can make prints without

inserting the key counter.

Note

❒ Default: Not to use

7. On Line Mode

No.

Mode

Description

Set aut-O/L def

Specifies whether Auto On Line mode is set to “On” or “Off”

when power is switched on or after mode settings are cleared.

Note

❒ Default: On

Ppr. Size [Online]

List/Test Print

Print PS Errors

Specifies the paper size when you press the {On Line} key.

Note

❒ Default: Auto

Prints the current set content of this machine.

Note

❒ Default: System Print

Setting for when printing the PS Error List when a PostScript er-

ror occurs.

Note

❒ Default: Off

151

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

No.

Mode

Description

IP Address

Sets the IP Address.

Note

❒ Default: 011.022.033.044

Reference

See the Printer Reference 1 for information about the IP Ad-

dress setting.

Ethernet Speed

Network

Sets the Ethernet communication speed.

Note

❒ Default: Auto

Sets the Network boot.

Note

❒ Default: NONE

Reference

See the Printer Reference 1 for information about the Net-

work boot setting.

I/O Timeout

Sets the time to enable the interface after data stops being re-

ceived. When the time set here is exceeded, it will be possible to

receive data from the other interface.

Important

❒ If the set time is too short, a time out might occur while one

data is being received. As a result, data from another inter-

face might cut in and be printed, or the emulation retrieval

from half of the data may be activated, and be replaced with

a different emulation.

Note

❒ Default: 30 sec.

I/O Buffer

Sets the capacity of the reception buffer.

Note

❒ Default: 512KB

Menu Reset

You can reset the factory settings. However, the “IP Address”,

“Network”, and the “Ethernet Speed” settings do not change.

152

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

E Press the {q} key.

1-6 Time Setting

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

F Enter the month with the number

ZDZS110N

keys.

G Press the {q} key.

B Make sure that “1” is selected,

and then press the [OK] key.

Note

❒ Follow steps F and G for the

"date", "hour", "minute", and

"second".

H Press the [OK] key.

C Enter 6 with the number keys,

andthenpressthe[OK]or{q}key.

D Enter the year with the number

keys.

153

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

F Enter the desired ratio with the

3-4 Reproduction Ratio

[←] [→] or {~} {}} keys.

Note

A Press the {User Tools} key.

❒ You can also enter the ratio with

the number keys.

G Press the [OK] key twice.

Image Density

Lighter

Stamp

On Line

3-5 Class Enter No.

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

A Press the {User Tools} key.

ZDZS110N

B Enter 3 with the number keys,

andthenpressthe[OK]or{q}key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

C Enter 4 with the number keys,

andthenpressthe[OK]or{q}key.

B Enter 3 with the number keys,

andthenpressthe[OK]or{q}key.

D Select the ratio you want to adjust

with the [←] [→] or {~} {}} keys.

C Enter 5 with the number keys,

andthenpressthe[OK]or{q}key.

E Press the [Adjust.] key.

154

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

D Select the grade with the [←] [→] H Press the [OK] key.

or {~} {}} keys.

Note

❒ Repeat steps D through H until

you have finished registering

the number of students in each

class for the each grades.

I Press the [OK] key.

3-11 Margin Erase Area

E Press the [Enter] key.

A Press the {User Tools} key.

F Select the class with the [←] [→]

or {~} {}} keys.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

G Enter the number of students

with the number keys, and then

press the {q} key.

B Enter 3 with the number keys,

andthenpressthe[OK]or{q}key.

C Enter 11 with the number keys,

andthenpressthe[OK]or{q}key.

Note

❒ Repeat steps F and G until you

have finished registering the

number of students in each

class.

155

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

C Enter the vertical length with

D Select the original size you will

use with the [←] [→] or {~} {}}

keys.

the number keys.

D Press the {q} key.

E Enter the horizontal width

with the number keys.

F Press the {q} key.

G Press the [OK] key twice.

4-11 No. of Skip Feed

The following procedure explains

how to change the number of drum

rotations.

E Press the [Select] key.

F Adjust the erase edge margin.

A Press the {User Tools} key.

If you selected A3 to A6 or 11" ×

17" to 5¹/₂" × 8¹/₂"

A Adjust the erase edge margin

with the [←] [→] or {~} {}}

keys.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

B Enter 4 with the number keys,

and then press the [OK] or {q}

key.

Note

❒ You can also enter the ratio

with the number keys and

the {q} key.

C Enter 11 with the number keys,

and then press the [OK] or {q}

key.

If you selected p

A Enter the erase edge margin

with the number keys.

B Press the {q} key.

156

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

D Press the [Change] key.

4-14 No. of Q.start

Note

❒ The default settings are as follows.

Time period

E Change the number of drum rota-

tions while one sheet of paper is

fed with the [←] [→] or {~} {}}

keys.

Low Tmp.

15 45 45

Normal Tmp.

15 15

High Tmp.

(10 – 15°C, 50 – 59°F)

(15 – 28°C, 59 – 82.4°F)

(28 – 30°C, 82.4 – 86°F)

A Press the {User Tools} key.

Note

❒ You can also change the num-

ber of rotations with the num-

ber keys.

Image Density

Lighter

F Press the [OK] key.

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

B Enter 4 with the number keys,

andthenpressthe[OK]or{q}key.

C Enter 14 with the number keys,

andthenpressthe[OK]or{q}key.

157

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

D Select the temperature at which

you use this machine with the [←]

[→] or {~} {}} keys.

4-19 Type of Paper

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

E Press the [OK] key.

ZDZS110N

F Select the time period (hours) the

drum unit idles for with the [←]

[→] or {~} {}} keys.

B Enter 4 with the number keys,

andthenpressthe[OK]or{q}key.

C Enter 19 with the number keys,

andthenpressthe[OK]or{q}key.

G Press the [OK] key.

H Select the number of drum rota-

tions with the [←] [→] or {~} {}}

keys.

D Select [User1] or [User2] with the

[←] [→] or {~} {}} keys.

I Press the [OK] key.

E Press the [OK] key.

158

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

Stamp

positions

Default

Available

settings

F Select the paper type and misfeed

condition with the [←] or [→] key.

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

b = 24mm,

0.96"

b = 8 –

144mm,

GRSPOS3E

0.32" – 5.76"

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

b = 0mm, 0"

b = – 72 –

72mm, –

2.88" – 2.88"

c = center

line

G Press the [OK] key.

GRSPOS4E

H Press the [Cancel] key.

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

5-4 Stamp Position

b = 24mm,

0.96"

b = 8 –

144mm,

0.32" – 5.76"

GRSPOS5E

Note

❒ The default position and available

settings of each stamp are as fol-

lows.

a = 0mm, 0" a = – 52 –

52mm, –

2.08" – 2.08"

b = 24mm,

0.96"

Stamp

Default

Available

settings

b = 8 –

144mm,

0.32" – 5.76"

c = center

line

positions

GRSPOS6E

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

a = 0mm, 0" a = – 52 –

52mm, –

2.08" – 2.08"

b = 24mm,

0.96"

b = 0mm, 0"

b = 8 –

144mm,

0.32" – 5.76"

c = center

line

GPSPOS0E

b = – 72 –

72mm, –

GRSPOS7E

2.88" – 2.88"

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

a = 0mm, 0" a = – 52 –

52mm, –

2.08" – 2.08"

b = 0mm, 0"

b = 24mm,

0.96"

b = – 72 –

72mm, –

2.88" – 2.88"

c = center

line

GRSPOS1E

b = 8 –

144mm,

0.32" – 5.76"

c = center

line

GRSPOS8E

a = 24mm,

0.96"

a = 8 –

104mm,

0.32" – 4.16"

b = 24mm,

0.96"

b = 8 –

144mm,

GRSPOS2E

0.32" – 5.76"

159

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

Note

A Press the {User Tools} key.

❒ The value increases or decreases

in 4mm, 0.16" steps.

G Adjust the vertical stamp position

with the {|} or {{} key.

Image Density

Stamp

On Line

Lighter

H Press the [OK] key twice.

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

5-7 Position (Date)

ZDZS110N

Note

B Enter 5 with the number keys,

❒ The default position and available

settings of each date stamp are as

follows.

andthenpressthe[OK]or{q}key.

Stamp

positions

Default

Available

settings

a = 8mm,

0.32"

a = 8 –

40mm,0.32"

– 1.60"

C Enter 4 with the number keys,

dd.mm.yy

andthenpressthe[OK]or{q}key.

b = 20mm,

0.80"

b = 8 –

40mm,0.32"

– 1.60"

GRDPOS0E

D Select the stamp position you

want with the [←] [→] or {~} {}}

keys.

dd.mm.yy

GRDPOS1E

a = 20mm,

0.80"

b = 12mm,

0.48"

GRDPOS2E

a = 20mm,

0.80"

E Press the [Change] key.

b = 8mm,

0.32"

F Adjust the horizontal stamp posi-

tion with the {|} or {{} key, and

then press the {}} key.

GRDPOS3E

160

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

A Press the {User Tools} key.

F Adjust the horizontal date stamp

position with the {|} or {{} key,

and then press the {}} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

Note

❒ The value increases or decreases

in 4mm, 0.16" steps.

ZDZS110N

B Enter 5 with the number keys,

G Adjust the vertical date stamp po-

andthenpressthe[OK]or{q}key.

sition with the {|} or {{} key.

H Press the [OK] key twice.

5-10 Position (Page)

C Enter 7 with the number keys,

Note

andthenpressthe[OK]or{q}key.

❒ The default position and available

settings of each page stamp are as

follows.

❖ P1 or ¹/₅

D Select the date stamp position

you want to adjust with the [←]

[→] or {~} {}} keys.

Stamp

positions

Default

Available

settings

a = 8mm,

0.32"

a = 8 –

40mm,0.32"

– 1.60"

P.1

b = 12mm,

0.48"

b = 8 –

40mm,0.32"

– 1.60"

GRPPOS0E

a = 12mm,

0.48"

b = 12mm,

0.48"

GRPPOS1E

E Press the [Change] key.

161

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

❖ -1-

D Select the page numbering direc-

tion you want to adjust with the

[←] [→] or {~} {}} keys.

Stamp

positions

Default

Available

settings

a = 8mm,

0.32"

a = 8 –

40mm,0.32"

– 1.60"

–1–

GRPPOS2E

a = 8mm,

0.32"

a = 8 –

40mm,0.32"

– 1.60"

E Press the [Change] key.

GRPPOS3E

F Adjust the horizontal page num-

bering position with the {|} or

{{} key, and then press the {}}

key.

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Note

Auto On Line

Make-Up

❒ The value increases or decreases

ZDZS110N

in 4mm, 0.16" increments.

G Adjust the vertical page number-

ing position with the {|} or {{}

key.

B Enter 5 with the number keys,

andthenpressthe[OK]or{q}key.

Note

❒ You need not follow step G

when you select “-1-” as the di-

rection in step D.

C Enter 10 with the number keys.

Then press the [OK] or {q} key.

H Press the [OK] key twice.

162

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

G Pressthe{q}or{Clear/Stop}keyto

5-11 Make/Chg. Pattern

edit the pattern.

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

Note

❒ To add a dot, press the {q} key.

B Enter 5 with the number keys,

❒ To remove a dot, press the

andthenpressthe[OK]or{q}key.

{Clear/Stop} key.

❒ Repeat steps F and G until you

have finished editing the pat-

tern.

H Press the [OK] key twice.

C Enter 11 with the number keys,

andthenpressthe[OK]or{q}key.

D Select the background pattern

with the {~}, {}}, {|}, or {{}

key.

E Press the [Change] key.

F {Move the cursor to the position you

wish to edit with the {~}, {}}, {|},

or {{} keys.}

163

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

D Keep pressing the [→] or {}} key

to display the number of masters

and prints made under your user

code.

6-1 Check Counter

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

E Press the [OK] key after checking

the number of masters and prints

made under your user code.

B Enter 6 with the number keys,

andthenpressthe[OK]or{q}key.

6-2 Reset Counters

A Press the {User Tools} key.

C Make sure that 1 is selected, and

then press the [OK] key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

B Enter 6 with the number keys,

Note

andthenpressthe[OK]or{q}key.

❒ The number of masters and

prints made under the first user

code will be displayed in the

panel display.

164

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tool Menus in Detail

C Enter 2 with the number keys,

and then press the [OK] or {q}

key.

6-5 Chg. User Code

A Press the {User Tools} key.

D Select [Single] or [All] with the [←]

Image Density

Lighter

Stamp

On Line

[→] or {~} {}} keys.

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

B Enter 6 with the number keys,

andthenpressthe[OK]or{q}key.

E Press the [OK] key.

If you selected [Single]

C Enter 5 with the number keys,

andthenpressthe[OK]or{q}key.

A Keep pressing the [→] or {}}

key to display the number of

masters and prints made under

your user code.

D Keeppressingthe[→]or{}}keyto

display your user code.

B Press the [OK] key.

C Press the [Yes] key.

D Press the [Cancel] key twice.

E Press the [OK] key.

If you selected [All]

A Press the [Yes] key.

165

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

F Enter the new user code with the D Keep pressing the [→] or {}} key

number keys.

to display your user code.

E Press the [OK] key.

G Press the [OK] key.

F Press the [Yes] key.

6-6 Del. User Code

A Press the {User Tools} key.

Image Density

Lighter

Stamp

On Line

Normal

Darker 1

Darker 2

Auto On Line

Make-Up

ZDZS110N

B Enter 6 with the number keys,

andthenpressthe[OK]or{q}key.

C Enter 6 with the number keys,

and then press the [OK] or {q}

key.

166

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Troubleshooting

If Your Machine Does Not Operate as You

Want

If a malfunction or a misfeed occurs, the following messages will appear on the

panel display.

Message

Meaning

Check the original direc- The paper is not placed in the same direction as the original.

tion.

Place the original in the same direction as the paper.

If you press the {Print} key, the selected paper will be used for print-

ing.

Size of original and pa- Set a paper size that matches the reproduction ratio you have select-

per is not the same.

ed and your original.

The reproduction ratio selected by Auto Magnification mode is too

big or too small.

Note

❒ You can make prints if you press the {Print} key.

Set original.

Make prints after confirming whether there is an original on the ex-

posure glass.

Make sure that you have changed the original on the exposure glass

before pressing the {Start} key.

Max. quantity: ****

Min. quantity: ****

The number of prints exceeds the maximum print quantity.

You can change the maximum number of prints that can be made in

one operation with the user tools. See “Max. Quantity” on p.142 “2.

Set Operat'n Mode”.

The number of prints does not exceed the minimum print quantity.

You can change the minimum number of prints that can be made in

one operation with the user tools. See “Min. Quantity” on p.142 “2.

Set Operat'n Mode”.

Drum unit is not set. Set Slide in the drum until it clicks.

Drum unit.

Make sure that the drum is completely set in position.

Communication error

Turn the main switch off and on.

Turn the main switch off If the message appears again, contact your service representative.

then on

Overloaded for the de-

livery tray

Remove the paper from the delivery tray.

Reference

Please remove the paper

See “Delivery Capacity” on p.142 “2. Set Operat'n Mode”.

167

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Message

Meaning

Print image is larger

The master image previously printed is larger than the paper, the

than the selected paper image exceeds the paper size.

size.

Make prints again after pressing the [Exit] key and selecting the pa-

Change the paper size.

per size again.

Note

❒ If you press the [Exit] key to erase the message and press the

{Print} key, the machine starts to make the prints. However, the

image might not fit on the paper.

-When a service call message is shown on the panel display

Press the [Exit] key. Then turn the main switch off and back on again. If a service

code appears again, contact your service representative.

Note

❒ If a service code appears on the panel display after you turn the main switch

off and on a few times, do not continue turning it on and off. Leave the ma-

chine off.

❒ When you make masters continuously using originals with solid images,

“SC-03-03” tends to appear on the panel display. In this case, turn off the main

switch and wait for a while. Then turn on the main switch.

168

Download from Www.Somanuals.com. All Manuals Search And Download.

If You Cannot Make Prints as You Want

Problem

Cause

Action

Misfeeds occur frequently.

Improper paper type is select- Select proper paper type. See

ed.

p.43 “Printing onto Various

Kinds of Paper”.

When you try to set several

functions at a time, you can-

not set some functions.

Some functions cannot be

used together.

See p.135 “Combination

Chart”.

Parts of the image are not

printed in Edge Erase mode.

Erase margin is too wide.

Set a narrower erase margin

with the user tools. See p.155

“3-11 Margin Erase Area”.

Edge margins of original are

too narrow.

Prints are blank or parts of the The paper feed side plates are Make sure that the paper feed

image are not printed.

not set correctly.

side plates touch the paper

lightly and the proper paper

size is displayed in the panel

display.

2nd printing with another

drum is unsatisfactory.

The 1st print image is still wet. Wait until the 1st image be-

comes dry.

An uneven solid image ap-

pears.

Large solid image wrinkles

the master.

Increase the print speed or se-

lect photo mode.

Combine Originals Mode

Problem

Cause

Action

Prints are blank or parts of the Original size and direction are You cannot use originals of

image are not printed.

not correct.

different sizes and directions

in Combine Originals mode.

Use originals of same size and

direction.

Print image is not correct.

Original set order is not cor-

rect.

Place originals face up in the

optional document feeder.

The first original should be on

top.

Place original face down on

the exposure glass. The first

original should be set first.

169

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Loading Paper

The Load Paper indicator (B) lights

when the paper feed tray runs out of

paper.

B Adjust the paper feed side plates

to match the paper size.

Limitation

❒ Load paper when the paper feed

tray is completely empty. If you

add paper when some paper is left

in the tray, it may cause multiple

feeds or misfeeds.

Reference

For available paper sizes, see p.11

“Print Paper”.

Note

❒ Make sure that the paper size

and direction shown on the

panel display match the size

and direction of paper loaded in

the paper feed tray.

A Load the paper in the paper feed

tray.

170

Download from Www.Somanuals.com. All Manuals Search And Download.

x Clearing Misfeeds

R CAUTION:

• Be careful not to cut yourself on

any sharp edges when you reach

inside the machine to remove

misfed sheets of paper or mas-

ters.

-To prevent paper misfeeds:

Check the following before restarting

the printing run.

• Did you select an appropriate pa-

per type with the [Ppr.Type] key?

Note

❒ After clearing misfeeds, make sure

that all the doors, covers, and units

are closed and the x indicator is

off.

❒ To prevent misfeeds, do not leave

any torn scraps of paper, originals,

or masters in the machine.

❒ When clearing misfeeds, do not

turn off the main switch. If you do,

your print settings will be cleared.

• Are the side pads in the correct po-

sitions?

❒ If misfeeds occur repeatedly,

please contact your service repre-

sentative.

”x + A” Paper Misfeeds in the

Paper Feed Section

To print on thin paper (47.1g/m²,

12.5 lb), slide the levers behind the

paper feed side plates in the direc-

tion of the arrow (see illustration).

A Remove the misfed paper.

• When paper is curled, correct as

shown.

Z066

171

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

• When paper edges stick together

or paper is not fed in, fan the paper

as shown.

”x + A + B” Paper Misfeeds in

the Paper Feed Section

A Open the front door.

B Lower drum unit lock lever (B1).

Z067

• When printing onto postcards or

thick paper, lower the printing

speed to setting 1 or 2. See p.27

“Changing the Printing Speed”.

C Take out the drum.

• When a multiple feed occurs or the

paper comes out skewed, make

sure that the paper feed side plates

are properly adjusted. When you

load paper on the paper feed tray,

make sure that the paper edge

touches the back fence and paper is

placed on the proper paper size

scale. Only use paper where the

leading edge has two right angle

corners.

Note

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

D Gently pull out the misfed paper

from the inside.

172

Download from Www.Somanuals.com. All Manuals Search And Download.

x Clearing Misfeeds

E If you cannot remove the misfed C Take out the drum.

paper, remove it from the paper

feed tray.

F Set the drum unit and close the

front door.

Note

❒ For setting the drum unit, see

Note

p.130 “Changing the Color

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

-To prevent paper misfeeds:

D While pressing the drum lock,

grasp the edge of the master (the

white area) and peel it off.

See p.171 “”x + A” Paper Misfeeds

in the Paper Feed Section”.

”x + B” Paper or Master

Wrapped Around the Drum

E Return the drum lock to its origi-

When the master is wrapped around the

drum

nal position.

F Set the drum unit and close the

A Open the front door.

front door.

B Lower drum unit lock lever (B1).

Note

❒ For setting the drum unit, see

p.130 “Changing the Color

Drum Unit”.

When paper is wrapped around the drum

A Open the front cover.

173

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

B Lower drum unit lock lever (B1).

When paper is misfed inside the machine

A Open the front cover.

B Lower drum unit lock lever (B1).

C Take out the drum.

Note

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

Note

D Remove the misfed paper from

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

the drum.

D Remove the misfed paper from

the inside as shown in the illus-

tration.

E If you cannot find misfed paper

around the drum (as in step D),

check the pressure cylinder. Re-

move any misfed paper.

F Set the drum unit and close the

E If you cannot remove the misfed

paper, remove paper from the

pressure cylinder.

front door.

Note

❒ For setting the drum unit, see

p.130 “Changing the Color

Drum Unit”.

174

Download from Www.Somanuals.com. All Manuals Search And Download.

x Clearing Misfeeds

F Set the drum unit and close the

”x + C” Paper Misfeeds in the

Paper Exit Section

front door.

Note

❒ For setting the drum unit, see

p.130 “Changing the Color

Drum Unit”.

A Slowly, but firmly pull out the

misfed paper.

-To prevent paper misfeeds:

If the paper is curled or the original's

leading edge margin is too narrow,

the following action is necessary.

• When you use curled paper, cor-

rect as shown.

-To prevent paper misfeeds:

When thin paper misfeeds in the pa-

per exit section, reduce the printing

speed with the {W}{V} {Speed} keys.

See p.27 “Changing the Printing

Speed”. If you cannot reduce the

printing speed, close the trailing edge

guides or move the end plate toward

the paper delivery tray edge.

Z066

• When the leading edge margin of

the original is less than 8mm, 0.32"

or there is a solid image on the

leading edge, insert the original

with the widest margin first or

make a leading edge margin by

making a copy.

* Less than 8mm, 0.32"

175

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

G Position the master roll so that the

edge reaches the interior of the

master holder.

”x + D” Master Misfeeds in

the Master Feed Section

A Pull out the master tray until it

stops.

B Open the master guide.

H Close the master guide.

C Open the master tray cover (1).

D Remove the master roll (2).

I Push in the master tray until it

stops.

”x + D + B” Master Misfeeds

in the Master Feed Section

E Reset the master roll (1).

A Open the front door.

Note

B Lower drum unit look lever (B1).

❒ The master roll must be posi-

tioned as shown in the illustra-

tion in step F.

F Close the master tray cover (2).

176

Download from Www.Somanuals.com. All Manuals Search And Download.

x Clearing Misfeeds

C Take out the drum.

”x + B + E” Master Misfeeds

in the Master Eject Section

A Open the front door.

B Lower drum unit lock lever (B1).

C Take out the drum.

Note

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

D Pull out the misfed master from

inside.

E Set the drum unit and close the

Note

front door.

❒ For taking out the drum unit,

see p.130 “Changing the Color

Drum Unit”.

Note

❒ For setting the drum unit, see

p.130 “Changing the Color

Drum Unit”.

D Grasp handle (E1) and pull out

the master eject unit until it stops.

E 1

177

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

E Pull out lever (E3) and remove the

”x + E” Master Misfeeds in

the Master Eject Section

misfed master.

A Open the front door.

B Grasp handle (E1) and pull out

the master eject unit until it stops.

E 1

C Check where the misfed master

F Return lever (E3) and the master

eject unit to their original posi-

tions.

is. Remove the misfed master.

G Set the drum unit and close the

front door.

Note

❒ For setting the drum unit, see

p.130 “Changing the Color

Drum Unit”.

D Return the master eject unit to its

original position and close the

front door.

178

Download from Www.Somanuals.com. All Manuals Search And Download.

x Clearing Misfeeds

”x + P” Original Misfeeds

Occur When Using the

Optional Document Feeder

-If master misfeeds occur often

If the master misfeeds often, frag-

ments of the master might be left in

the bottom of the master tray. Re-

move the fragments.

A Open the document feeder (ADF)

cover.

A Slide out the master tray.

ZDCY090E

B Pull out the misfed original gen-

tly.

B Open the cover at the bottom of

the master tray while holding the

lever and remove the fragments.

ZDCY120E

C If you cannot remove misfed orig-

inals as in step B, open the docu-

ment feeder.

C Close the black cover and slide in

D Pull the green knob towards you

the master tray.

and remove the misfed original.

Note

❒ Make sure that you securely

close the black cover before slid-

ing in the master tray.

TPEH220E

179

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

• Originals written in pencil

E Return the document feed sheet

• Thin originals that have low stiff-

to its original position.

ness

F Close the document feeder (ADF)

cover until it clicks in position

and if necessary, close the docu-

ment feeder.

• Originals with index tabs

• Transparent originals such as OHP

transparencies or translucent pa-

per

Note

❒ Do not mix different sizes of origi-

nals in the optional document

feeder.

❒ Remove staples or paperclips from

originals. Fan originals that have

had staples or paperclips removed.

ZDCY100E

❒ Do not stack originals above the

limit mark.

-To prevent originals

misfeeding:

Placing the following kinds of origi-

nals on the exposure glass may cause

misfeeds.

• Originals heavier than 128g/m², 34 lb

• Originals lighter than 52g/m², 14 lb

• Originals smaller than 148mm ×

210mm, 5.9" × 8.3"

• Originals larger than 297mm ×

864mm, 11.6" × 34.0"

• Stapled or clipped originals

• Perforated or torn originals

• Curled, folded, or creased origi-

nals

• Originals with any kind of coating,

such as thermal fax paper, art pa-

per, aluminum foil, carbon paper,

or conductive paper

• Bound originals such as books

• Damaged originals

• Originals with glue on them

• Pasted originals

180

Download from Www.Somanuals.com. All Manuals Search And Download.

When the Open Cover/Unit Indicator (M) Lights

When the Open Cover/Unit Indicator (M)

Lights

MMake sure that the following

doors/covers are closed.

❖ Front door

Close the front door completely.

❖ Optional document feeder (ADF) cov-

Close the document feeder (ADF)

cover until it locks in position.

ZDCY100E

181

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

When the Add Ink Indicator (j) Lights

The Add Ink indicator (j) lights when it is time to supply ink.

R CAUTION:

• If ink comes into contact with your eyes, rinse immediately in running water.

For other symptoms, consult a doctor.

R CAUTION:

• Keep the ink or ink container out of reach of children.

R CAUTION:

• If ink is ingested, induce vomiting by drinking a strong saline solution. Con-

sult a doctor immediately.

R CAUTION:

• Our products are engineered to meet high standards of quality and function-

ality, and we recommend that you use only the expendable supplies avail-

able at an authorized dealer.

Note

❒ Be sure to supply ink of the same color as the current drum.

❒ Ink is easily removed from skin by waterless hand cleaners followed by wash-

ing with soap and water.

❒ Be careful not to get any ink on your clothing.

❒ Store ink under low temperature and humidity conditions.

❒ Do not store ink where it will be exposed to heat or direct sunlight.

❒ Store on a flat surface.

A Open the front door.

B Pull out the ink holder.

182

Download from Www.Somanuals.com. All Manuals Search And Download.

When the Add Ink Indicator (j) Lights

C Remove the used ink cartridge.

D Remove the cap of the new ink cartridge.

E Insert the new cartridge into the ink holder.

Note

❒ Always supply ink of the same color.

F Return the ink holder to its original position until it clicks.

G Close the front door.

The machine will start idling to supply ink to the drum.

183

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

When the Master End Indicator (C) Lights

The Master End indicator (C) lights when it is time to replace the master roll or

when you need to set the master roll.

R CAUTION:

• Our products are engineered to meet high standards of quality and function-

ality, and we recommend that you use only the expendable supplies avail-

able at an authorized dealer.

A Pull out the master tray until it stops.

B Open the master guide.

C Open the master tray cover (1).

D Remove the used master roll (2).

Note

❒ When the Master End indicator is lit, it is necessary to replace the master

roll even if some master remains on the old roll.

E The new master roll must be positioned as shown in the illustration (1).

F Close the master tray cover (2).

184

Download from Www.Somanuals.com. All Manuals Search And Download.

When the Master End Indicator (C) Lights

G Position the master roll so that the edge reaches the interior of the master

holder.

H Close the master guide.

I Push in the master feed unit until it stops.

185

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

When the Master Eject Indicator (k) Lights

The Master Eject indicator (k) lights

F Remove the used master by push-

when it is time to empty the master

ing down the handle (1) towards

eject unit or when you need to set the

the waste container (2).

master eject unit.

Note

❒ Ink is easily removed from skin by

waterless hand cleaners followed

by washing with soap and water.

❒ Be careful not to get any ink on

your clothing while emptying the

master eject unit.

Note

❒ If you cannot remove the used

master completely, repeat step

F until all the master is re-

moved.

A Prepare a container for the used

master.

B Open the front door.

G Reinstall the master eject unit,

making sure it clicks into posi-

tion.

C Use handle (E1) to pull out the

master eject unit until it stops.

H Close the front cover.

D Pull up handle (E2) and pull out

the master eject unit completely.

E 1

E Hold the master eject unit upper

handle and turn it clockwise with

one hand while holding handle

(E1) with other hand (1).

186

Download from Www.Somanuals.com. All Manuals Search And Download.

When Other Indicators Are Lit

Indicator

Meaning and action

The key counter (option) is not set. Insert the key counter.

TPES270E

•

(Metric version)

Color drum unit is installed.

A3 A4

TPES280E

(Inch version)

8¹/²Color

TPES280N

•

(Metric version)

A3/11" × 17" drum unit is set.

A3 A4

TPES290E

(Inch version)

Drum

17 8¹/²Co

TPES290N

A4/8¹/₂" × 11" drum unit is set.

•

(Metric version)

A3 A4

TPES300E

(Inch version)

Drum

17 8¹/²Co

TPES300N

187

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

When Prints Are Not Delivered in a Neat

Stack

Note

When Printing on Small Size

Paper

❒ Make sure that the paper size

and direction in the panel dis-

play match the actual paper size

and direction of the paper on

the feed tray.

A Adjust the angle of the end plate

by turning the screw clockwise or

counterclockwise.

❒ If the paper on the paper feed

tray has a solid image on its

back side, the machine may not

be able to detect the size correct-

ly. Place a sheet of paper of the

same size without an image on

the back at the bottom of the pa-

per stack.

When the Machine Cannot

Detect the Paper Size

If the paper size is not detected cor-

rectly when printing, prints might not

be delivered in a neat stack. To solve

this, do one of the following:

A Re-adjust the paper feed side

plates so that there is no space be-

tween the side plates and the pa-

per, and then lock the side plates

in position.

188

Download from Www.Somanuals.com. All Manuals Search And Download.

Poor Printing

Dirty Background

If the background of prints is dirty, the drum unit might be dirty.

R CAUTION:

• If ink comes into contact with your eyes, rinse immediately in running water.

For other symptoms, consult a doctor.

R CAUTION:

• Keep the ink or ink container out of reach of children.

R CAUTION:

• If ink is ingested, induce vomiting by drinking a strong saline solution. Con-

sult a doctor immediately.

Note

❒ To avoid getting dirty background prints when printing onto paper smaller

than the original image, select a suitable reduction ratio or use larger print pa-

per.

❒ When printing onto paper that does not absorb ink well, like postcards, the

background of prints might be dirty. In this case, lower the printing speed or

use Skip Feed mode to dry the ink on the prints.

A Turn off the main switch.

TPEH020E

189

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

B Pull out the drum unit.

TPEH101E

Note

❒ For taking out the drum unit, see p.130 “Changing the Color Drum Unit”.

C While pressing the drum lock, turn the drum until you can see the trailing

edge of the master.

D With a dry soft cloth, remove any ink that has accumulated on the trailing

edge of the drum unit.

Important

❒ Do not use benzine, thinner, or other organic liquids—doing so can dam-

age the machine.

190

Download from Www.Somanuals.com. All Manuals Search And Download.

Poor Printing

E Turn the drum unit and lock it after cleaning.

F Insert the drum unit until it locks into position, and then lower the drum

unit lock lever.

TPEH091E

G Close the front door.

H Turn on the main switch.

TPEH021E

191

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Black Lines/Stained Prints

Check the platen cover and clean it if dirty. See p.197 “Cleaning the platen cov-

er”.

Check the exposure glass and clean it if dirty. See p.197 “Cleaning the exposure

glass”.

Check the sheet of the optional document feeder and clean it if dirty. See p.198

“Cleaning the Sheet”.

Note

❒ If black lines or stains still appear on prints even following the cleaning pro-

cedures above, please contact your service representative.

Faint Prints

If the machine is not used for a long period of time or you change the color drum

unit, the ink on the drum might dry causing print quality to deteriorate. To solve

this problem, use Quality Start mode. See p.76 “Quality Start Mode”.

If the print density is still too light even if you use Quality Start mode, remake

the master.

192

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Remarks

Do's and Don'ts

R CAUTION:

• Unplug the power cord from the wall outlet before you move the machine.

While moving the machine, you should take care that the power cord will not

be damaged under the machine.

Important

❒ Make sure that the m indicator on the PC controller operation panel is off be-

fore unplugging the power cord.

• While printing, do not turn off the main switch.

• While printing, do not unplug the power cord.

• While printing, do not open the door or covers.

• While printing, do not move the machine.

• Open and close all doors and covers carefully.

• When printing onto paper that contains images on the back, make sure there

is a 10mm (0.4") margin at the back leading edge. If there is no margin, the ma-

chine might wrongly detect that paper is wrapped around the drum and stop

printing.

• When you use envelopes or pasted print paper, the leading edge of the prints

might be damaged.

• Always make a few trial prints to check the image position because the image

position of the trial print might not correspond with that of the original.

• The leading edge of the prints might become stained if the edge touches the

image of prints on the paper delivery tray.

• Print ink on the paper delivery tray might stick to the back side of the next

print.

• Press the {Proof} key to perform a test print as the image density of the first

few prints might be light.

• When the machine is on and the power source is less than 90% of the specified

amount, printing quality will decrease. Therefore, make sure the supply from

your electrical outlet is at least 90% of the required amount.

• When you make a lot of prints from a small image, ink might ooze out from

the edges of the master, especially in high temperatures and when printing in

two or more colors. In these cases, make a new master.

• Remove the paper from the tray before relocating the machine. If you relocate

the machine leaving the paper on the tray, reset the paper after the relocation.

If the main switch of the machine is turned on without resetting the paper cor-

rectly, the sensor might be broken.

193

Download from Www.Somanuals.com. All Manuals Search And Download.

Remarks

• If the printed paper is stored for more than one day, the paper may become

wrinkled. If this paper is used, wrinkles may also appear on the master. If the

paper will be stored for more than one day, store it in its original wrapping

paper or other protective covering.

• Shadowing may occur if the printed image at the rear edge of the paper is a

solid color, when the printing speed is set to 1. If this occurs, print the image

with the printing speed set to 3.

• If there are fine lines within 5mm to 10mm, 0.2" to 0.4" of the edge of the im-

age, shadowing may occur.

• Depending on the type of paper being used, speckles may appear within

5mm to 10mm, 0.2" to 0.4" of the edge of the image at around 1000 prints.

• When two or more sheets of paper feed at once, set paper on the paper feed

side plates securely. See p.15 “Printing Preparations”.

• When paper misfeeds occur, select the proper paper type from [Ppr.Type]. See

p.43 “Printing onto Various Kinds of Paper”. If the problem persists, fan or

turn the paper over.

• If the paper skews, make sure to set the paper feed side plates securely. See

p.15 “Printing Preparations”.

• Make sure originals on the exposure glass are correctly positioned and

aligned with the scale.

• If the edges of the paper are rounded, skewing might occur. Change the pa-

per's orientation or replace.

• If the paper becomes creased, make sure the correct paper type has been se-

lected [Ppr.Type]. See p.43 “Printing onto Various Kinds of Paper”.

• If non-standard papers crease frequently, use the standard paper type.

194

Download from Www.Somanuals.com. All Manuals Search And Download.

Where to Put Your Machine

Environment

Your machine's location should be carefully chosen because environmental con-

ditions greatly affect its performance.

Optimum environmental conditions

R CAUTION:

• Keep the machine away from humidity and dust. Otherwise a fire or an elec-

tric shock might occur.

• Do not place the machine on an unstable or tilted surface. If it topples over,

an injury might occur.

R CAUTION:

• If you use the machine in a confined space, make sure there is a continuous

air turnover.

R CAUTION:

• After you move the machine, use the caster fixture to fix it in place. Other-

wise the machine might move or come down to cause an injury.

• Temperature: 10 – 30°C, 50 – 86°F

• Humidity: 20 – 90% RH

• A strong and level floor.

• The machine must be level within 5mm, 0.2" both front to rear and left to

right.

Environments to avoid

• Locations exposed to direct sunlight or strong light (more than 1500 lux).

• Locations directly exposed to cool air from an air conditioner or heated air

from a heater (sudden temperature changes might cause condensation within

the machine).

• Places where the machine might be subjected to frequent strong vibration.

• Dusty areas.

• Areas with corrosive gases.

195

Download from Www.Somanuals.com. All Manuals Search And Download.

Remarks

Power Connection

R WARNING:

• Connect the machine only to the power source described on the inside

front cover of this manual. Connect the power cord directly into a wall

outlet and do not use an extension cord.

• Do not damage, break or make any modifications to the power cord.

Do not place heavy objects on it. Do not pull it hard nor bend it more

than necessary. These actions could cause an electric shock or fire.

R CAUTION:

• Unplug the power cord from the wall outlet before you move the machine.

While moving the machine, you should take care that the power cord will not

be damaged under the machine.

R CAUTION:

• When you disconnect the power plug from the wall outlet, always pull the

plug (not the cable).

Make sure the plug is firmly inserted in the outlet.

Machine Clearance

Place the machine near the power source, providing clearance as shown.

❖ Main frame

* Paper delivery tray

1. More than 10cm, 4.0"

2. More than 60cm, 23.7"

3. More than 60cm, 23.7"

4. More than 60cm, 23.7"

196

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Machine

To maintain high print quality, clean

the following parts and units regular-

ly.

Cleaning the platen cover

A Lift the platen cover.

❖ Cleaning the machine

B Clean the platen cover with a

damp cloth and wipe it with a dry

cloth.

Wipe the machine with a soft,

damp cloth. Then wipe it with a

dry cloth to remove the water.

Important

❒ Do not use chemical cleaner or or-

ganic solvents, such as thinner or

benzene. If they get into the ma-

chine or melt plastic parts, a failure

might occur.

❒ Do not clean parts other than those

specified in this manual. Such

parts should be cleaned by your

service representative.

AM1P0100

Note

❒ If you do not clean the platen

cover, marks on the cover will

be printed.

Cleaning the Main Frame

Cleaning the paper feed roller (Paper

feed tray)

Cleaning the exposure glass

A Lift the platen cover or document

A Wipe dust off the paper feed roll-

er with a damp cloth, and then

wipe it with a dry cloth.

feeder.

B Clean A and B.

TPEH120E

ZDCH130E

Note

❒ If you do not clean the paper

feed roller, paper misfeeds tend

to occur.

197

Download from Www.Somanuals.com. All Manuals Search And Download.

Remarks

Cleaning the Optional

Document Feeder

Cleaning the Sheet

A Lift the document feeder.

B Clean the sheet with a damp cloth

and wipe it with a dry cloth.

AM1D600

Note

❒ If you do not clean the sheet,

marks on the sheet will be print-

ed.

198

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Specifications

Main Frame

❖ Configuration:

Floor standing (with custom table or cabinet).

❖ Printing Process:

Full automatic one drum system

❖ Original Type:

Sheet/Book

❖ Original Size:

Maximum 305mm × 432mm, 12.0" × 17.0"

❖ Pixel Density:

400dpi

❖ Image Mode:

Photo mode

Letter mode

Letter/Photo mode

Pencil mode

Tint mode

❖ Reduction Ratios:

• Inch version:

93%, 77%, 74%, 65%

• Metric version:

93%, 87%, 82%, 71%

❖ Enlargement Ratios:

• Inch version:

155%, 129%, 121%

• Metric version:

141%, 122%, 115%

❖ Zoom:

From 50% to 200% in 1% steps

❖ Directional Magnification:

• Vertical:

From 50% to 200% in 1% steps

• Horizontal:

From 50% to 200% in 1% steps

199

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

❖ Printing Area:

• A3 drum:

• Inch version: More than 290 × 420mm, 11.4" × 16.5"

• Metric version: More than 290mm × 410mm, 11.4" × 16.1"

• A4 drum:

More than 290mm × 200mm, 11.4" × 7.8"

❖ Print Paper Size:

Maximum recommended: 297mm × 432mm, 11.6" × 17.0" (Maximum: 320mm

× 447mm, 12.6" × 17.6")

Minimum: 70mm × 148mm, 2.8" × 5.8"

❖ Leading Edge Margin:

Less than 8mm, 0.32"

❖ Print Paper Weight:

• 47.1 – 209.3g/m², 12.5 – 55.6 lb

❖ Print Speed:

60 – 120rpm (5 steps)

❖ First Copy Time (Master Process Time):

Less than 16 seconds (A3, 11" × 17"L)

Less than 12 seconds (A4, 8¹/₂" × 11"K)

❖ Second Copy Time (First Print Time):

Less than 19 seconds (A3, 11" × 17")

Less than 15 seconds (A4, 8¹/₂" × 11")

❖ Color Printing:

Drum unit replacement system

❖ Image Position:

• Vertical:

• Inch version: 10mm, 0.4"

• Metric version: 15mm, 0.6"

• Side:

10mm, 0.4" (for either side)

❖ Paper Size and Paper Capacity:

1,000 sheets (80g/m², 20 lb)

❖ Paper Delivery Tray Capacity:

1,000 sheets (80g/m², 20 lb)

200

Download from Www.Somanuals.com. All Manuals Search And Download.

Main Frame

❖ Master Eject Unit Capacity:

• A3 drum

More than 60 masters

• A4 drum

90 masters

❖ Dimensions (W × D × H)

Width

Depth

Height

Stored

730mm, 28.8"

700mm, 27.6"

585mm, 23"

Stored with docu-

ment feeder

730mm, 28.8"

695mm, 27.4"

Set up

1435mm, 56.5"

700mm, 27.6"

585mm, 23"

Set up with cabinet

1,020mm, 40.2"

1,130mm, 44.5"

Set up with cabinet

anddocument feeder

(when you use A3,

11" × 17" or larger pa-

per)

❖ Weight:

• Machine:

Less than 97kg, 213.4 lb

❖ Noise Emission ^*1

Sound power level

Mainframe only

Stand-by

During printing

120cpm

Sound pressure level ^*2

Mainframe only

Stand-by

During printing

120cpm

The above measurements made in accordance with ISO 7779 are actual value.

It is measured at the position of the operator.

❖ Power Consumption:

• Making a master:

Less than 0.34kW

• Printing:

Less than 0.25kW

201

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

❖ Optional Equipment:

• Drum unit: Color Drums

Type 55(L) A3, 11" × 17"

Type 55(S) A4, 8¹/₂" × 11"

• Document Feeder Type 85

Note

❒ Specifications are subject to change without notice.

202

Download from Www.Somanuals.com. All Manuals Search And Download.

Document Feeder (Option)

❖ Original Type:

Sheet

❖ Original Weight:

52.3g/m²to 127.9g/m², 13.9 lb to 34 lb

❖ Original Size:

Max. 297mm × 864mm, 11.7" × 34.0"

Min. 149mm × 210mm, 5.9" × 8.3"

❖ Original Capacity:

50 sheets (80g/m², 20 lb)

7.5mm, 0.3" height

Color Drum Type 55(L) A3, 11"

17" (Option)

Color Drum Type 55(S) A4, 8¹/₂"

Exposure Glass Cover (Option)

× 11" (Option)

Printer Unit Type 80 RCP80 (Option)

Interface Cable Type 85 (Option)

Editing Function Type 85 (Option)

203

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Twin Color Press Roller Printing System TC-II

(Option)

❖ Configuration:

Floor standing (with custom table or cabinet)

❖ Printing Process:

Twin color press roller printing system

❖ Print Paper Size:

Maximum: 297mm × 432mm, 11.6" × 17.0"

Minimum: 70mm × 250mm, 2.8" × 9.8"

❖ Print Paper Weight:

• 52.3 – 209.3g/m², 13.9 – 55.6 lb

❖ Print Speed:

90–120cpm (3 steps)

❖ Color Printing:

Drum unit replacement system

❖ Paper Size and Paper Capacity:

1,000 sheets (80g/m², 20 lb)

❖ Paper Delivery Tray Capacity:

1,000 sheets (80g/m², 20 lb)

❖ Dimensions (W × D × H)

Width

Depth

Height

Stored

Set up

920 mm, 36.2"

1,610 mm, 63.4"

630 mm, 24.8"

555 mm, 21.9"

❖ Weight:

• Machine:

Less than 88kg, 194 lb

❖ Power Consumption:

• Printing:

0.55kW(Max)

❖ Optional Equipment:

• Drum unit: color Drums

A3, 11" × 17"

Note

❒ Specifications are subject to change without notice.

204

Download from Www.Somanuals.com. All Manuals Search And Download.

Consumables

Name

Size

Remarks

Master:

Length: 110m, 363ft/roll

A3 drum

Width: 320mm, 12.6" 2 Rolls/case

More than 200 masters can be made

per roll

A4 drum

330 masters can be made per roll

Ink-Black

1,000ml/pack

Environmental conditions: -5 to

40°C 10 – 95% RH

Ink-Red

Ink-Blue

Ink-Green

Ink-Brown

Ink-Purple

Ink-Yellow

Ink-Navy

Ink-Maroon

Ink-Teal

Ink-Orange

Ink-Gray

Ink-Violet

Ink-Hunter green

Ink-Burgundy

Ink-Gold

Note

❒ Specifications are subject to change without notice.

205

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Cancel, 9

{~}{}}{|}{{}, 7

Cancel Comb., 146

Changing the Printing Speed, 27

Check Counter, 150, 164

Chg. User Code, 150, 165

Class Enter No., 143, 154

{Class} key, 7

Class Manual Set, 144

Class Mode, 61

Clearing Misfeeds, 171

{Clear Modes/Energy Saver} key, 7

{Clear/Stop} key, 7

Closed area method, 91

Color Drum, 130, 187

Color drum indicator, 8

Color Printing, 130

16 single-sided originals → 1 single-sided

print of 16 images, 115

1 single-sided original → 1 single-sided

print of 2 images, 68

1 single-sided originals → 1 single-sided

print of 4 images, 68

2 single-sided originals → 1 single-sided

print with 2 images, 63

2 single-sided originals → 1 single-sided

print with 4 images, 63

4 single-sided originals → 1 single-sided

print of 4 images, 115

8 single-sided originals → 1 single-sided

print of 8 images, 115

Combination Chart, 135

Combine, 145

{Combine} key, 6

Combine Originals, 63

Combine Printing, 127

Comb. Sep. Line, 145

Command Sheet, 87

Consumables, 205

CopyCount Display, 142

Counter, 8

A3/11" × 17" drum indicator, 8

A3/11" × 17" drum unit, 187

A4/81/2" × 11" drum indicator, 8

A4/81/2" × 11" drum unit, 187

accessing the user tools, 139

Add Ink Indicator (j), 182

Adjusting the Image Density of Prints, 25

Adjusting the Position of Printed Images, 24

Administrator Mode, 150

All Class Mode, 52

Auto Class, 147

Auto Class Mode, 54

Auto Combine Mode, 68

Auto Cycle, 51

{Auto Cycle} key, 7

Auto Cycle ON/OFF, 144

Auto Magnification, 31

{Auto On Line} key, 6

Auto Quality Start, 76

Auto Reset, 141

Auto Rotation, 148

Auto Separate, 147

Data In indicator (Green), 8

Data Print, 142

Date Position Set, 149

Date Stamp, 108

Date Style Set, 149

Deflector Angle, 147

Del. User Code, 151, 166

Diagonal line method, 89

Directional Magnification (%), 36

Directional Magnification (Size), 38

Direction(Page), 149

Dirty Background, 189

Document feeder (ADF), 4

Drum Size, 134

Drum unit, 3

drum unit handle B2, 131

Drum unit lock lever B1, 3

Background ON/OFF, 145

Background Patterns, 86

Black Line/Stain, 192

206

Download from Www.Somanuals.com. All Manuals Search And Download.

Eco.Mode ON/OFF, 144

key counter, 187

Key Operator Code, 151

Keys, 6

Economy Mode, 50

{Economy Mode} key, 6

Edge Erase, 41

{Edge Erase} key, 6

Energy Saver Mode, 22

Energy Saving, 142

envelopes, 44

Language on LCD, 141

LCD Contrast, 142

Letter mode, 46

Letter/Photo Mode Printing, 46

List/Test Print, 151

Loading Paper, 15, 170

Load Paper indicator (B), 170

Longer Paper, 145

Environment, 195

Erasing Center and Edge Margins, 40

Error indicator (Red), 8

Ethernet Speed, 152

Exit, 9

Exposure Glass, 3

Exposure glass cover, 3

LT/Photo Contrast, 143

LT/Photo Priority, 143

Flip up cover, 1

Format, 105

Front door, 1

Machine Clearance, 196

Machine Exterior, 1

Machine Interior, 2

Main switch, 2

Maintaining Your Machine, 197

Make/Chg. Pattern, 149, 163

{Make-Up} key, 6

Make-up Printing, 94

Make-up Printing Features, 83

Make-up Samples, 97

Manual Class Mode with One Original, 57

Manual Class Mode with Two or More

Originals, 59, 128

Manual Quality Start, 76

Master, 184, 205

Master Eject Indicator (k), 186

Master End Indicator (C), 184

Master length, 79, 148

Master Misfeeds in the Master Eject

Section, 177, 178

Handle E1, 2

Idling for Q.start, 146

Ignore Paper Size, 144

{Image Density} key, 6

Image Overlay, 105

Image Rotation, 82

Indicators, 8

Initial Setting, 143

Ink, 182, 205

Ink holder, 3

Ink/Master Left, 147

I/O Buffer, 152

I/O Timeout, 152

IP Address, 152

Master Misfeeds in the Master Feed

Section, 176

Master tray, 1

Max. Quantity, 142

Memory Combine, 115

Menu Reset, 152

Min. Quantity, 142

Job Separation, 77

{Job Separator} key, 6

mm/inch, 141

Mode Setting, 144

Monitor indicators, 8

MSTR Makg. Density, 143

207

Download from Www.Somanuals.com. All Manuals Search And Download.

Poor Printing, 189

Position(Date), 149

Position(Page), 149

Power Connection, 196

Prev., 9

Printing in Two Colors, 132

{Print} key, 7

Print Paper, 11, 43, 170

Print PS Errors, 151

{Program} key, 7

Network, 152

Next, 9

No. of Q.start, 146, 157

No. of Skip Feed, 146, 156

No Orig. Size, 145

No Orig. Size DF, 144

Number keys, 7

Programs, 72

{Proof} key, 7

Protecting a Program, 73

OK, 9

{On Line} key, 6

On Line overlay, 105

On Line Printing, 80

Open Cover/Unit Indicator (M), 181

Operation Panel, 1, 6

Optional Document Feeder, 125

Options, 4, 202, 203

Original Misfeeds, 179

Original Modes, 46

Original Priority, 143

Originals, 13, 125

{q} key, 7

{Quality Start} key, 6

Quality Start Mode, 76

R. Cntr. Display, 141

Recalling a Program, 74

Reducing and Enlarging Using Preset

Ratios, 29

Reg/Chg KeyOpCode, 151

Reg. User Code, 150

Remarks, 193

Removing Program Protection, 73

Repeat, 120

Repeating an image over the entire print, 115

Reproduction Ratio, 154

Reproduct'n Ratio, 143

Reset Counters, 150, 164

Reset R. Counter, 141

Restricted Access, 151

Overlay, 105

{Overlay} key, 6

Page Stamp, 110

Panel Beeper, 142

Panel Display, 8, 9

Panel Display Layout, 10

Paper alignment wings, 2

Paper delivery end plate, 2

Paper delivery side plates, 2

Paper delivery tray, 2

Paper feed side plates, 1

Paper feed side plates knob, 1

Paper feed tray, 1

Paper feed tray down key, 1

Paper Misfeeds in the Paper Exit Section, 175

Paper Misfeeds in the Paper Feed Section,

171, 172

Paper or Master Wrapped Around the

Drum, 173

Paper Type, 43, 44, 45, 143

PC controller, 80, 106

Pencil Mode Printing, 48

Photo Contrast, 144

Photo Mode Printing, 47

Photo(Screen), 144

Safety Information, i

{Security} key, 6

Security Mode, 75

Select, 9

service call, 168

Set Operat'n Mode, 142

Setting Q.start, 146

Setting Up The Paper Delivery Tray, 16

Set User Code, 150

Size, 148

{Skip Feed} key, 6

Skip Feed Printing, 70

Special feature indicator, 8

208

Download from Www.Somanuals.com. All Manuals Search And Download.

special kinds of paper, 44

Specifications, 199

Stamp, 113, 148

Stamp Density, 148

{Stamp} key, 6

Stamp Position, 148, 159

Standard Paper, 43

Standard Printing, 19

{Start} key, 7

Stopping a Multi-print Run, 28

Storage Overlay, 105

Storing a Program, 72

System, 141

Thick Paper, 43

Time Setting, 141, 153

Tint Mode, 26

Trailing edge guides, 3

Troubleshooting, 167

Type, 148

Type of Paper, 147, 158

Type(Page), 149

User Code, 18, 150

User Tools, 139

{User Tools} key, 6

User Tools Menu, 141

What You Can do with this Machine, vi

when the image density is too light, 192

Where to Put Your Machine, 195

{W} {V} keys (Speed keys), 7

Zoom, 34

209

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

210

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

211

Download from Www.Somanuals.com. All Manuals Search And Download.

MEMO

212

UE USA C239

Download from Www.Somanuals.com. All Manuals Search And Download.

Type for 5455/LDD 150/JP5500/3360DNP

Printed in Japan

UE USA C239-8697

Download from Www.Somanuals.com. All Manuals Search And Download.

Reebok Fitness Home Gym RBBE14900 User Guide
Ricoh All in One Printer SP C231SF User Guide
Rotel Stereo Receiver RX404 User Guide
Ryobi Trimmer C430 RY34421 User Guide
Samsung Computer Monitor SyncMaste 721B User Guide
Sanus Systems Indoor Furnishings NFCD User Guide
Saturn Automobile 2005 Vue User Guide
Scag Power Equipment Lawn Mower SSZ 42 User Guide
Schwinn Exercise Bike 107P User Guide
Sears Power Supply 20071486 User Guide