Sapphire Audio Digital Camera Speed camera User Guide

Power Connection & Charging  
Sapphire  
Charging the internal battery  
2. Standby Screen  
Speed Limit  
20mph  
30mph  
40mph  
50mph  
Pre-Alert  
250m  
300m  
350m  
400m  
700m  
700m  
The device does not appear to respond to fixed speed camera systems  
Have you performed a download recently? If not, perform a fresh download to ensure that you have  
all the latest coordinates stored on your device.  
The Sapphire can be charged using the cigarette lighter adaptor in your vehicle or via the USB  
cable connected to your PC. When the unit is turned on the battery charge icon will be animated to  
indicate the battery is being charged.  
There are eleven different screen colour settings for the standby display. Please refer to the User  
Manual that can be found on the CD Rom to change the screen colour:  
G P S S p e e d C a m e r a D e t e c t i o n S y s t e m  
3. Adjusting the Volume  
Check your settings to see if you have ‘Smart Mute’ activated. If ‘Smart Mute’ has been activated the  
device will only alert you to GPS generated locations if you are travelling above the posted speed limit.  
Once fully charged the battery will last approximately 3 hrs during normal use.  
The Snooper Sapphire has an adjustable volume for controlling the loudness of the audible alert.  
To increase the volume push the ‘OK’ control on the right hand side of the unit upwards. To  
decrease the volume of the unit push the ‘OK’ control downwards.  
60mph  
70mph  
Using the cigarette lighter socket  
Take the lead and plug the smaller end into the 12V DC input socket on the bottom left hand side of  
the Sapphire and plug the cigarette lighter adaptor into your vehicles cigarette lighter socket.  
FURTHER TROUBLESHOOTING INFORMATION CAN BE FOUND IN THE FULL USER  
MANUAL SITUATED ON THE CD ROM  
You can also select your own preferred detection distance. For further information please consult  
the User Manual on the CD Rom.  
4. Cancelling an Alert  
If during an alert you decide that you would like to cancel it simply press and hold either the MEM  
or MUTE buttons.  
Please Note: Do not leave your Sapphire plugged into the cigarette lighter socket when you  
start your vehicle. As it is prone to power surges as the vehicle is started which may damage  
your unit.  
10. Road Type - ALL is selected as the factory default setting.  
Snooper Accessories & Price List  
In ‘ALL’ mode the Sapphire will provide alerts on all road types of any fixed speed safety cameras  
that are within range of the unit. Note: If you were travelling on a section of motorway for example  
it would mean that the unit could detect locations situated on an ‘A’ or ‘B’ road that is near to the  
motorway. As it is not on the road you are travelling though, it is not a threat and you might prefer  
to select the ‘Mway’ setting so that the unit would ignore these unwanted alerts. For further  
information on Road Type settings please consult the User Manual on the CD Rom.  
The following accessories are available from your local Snooper dealer. For further details please  
5. Logic Modes  
FOR FURTHER INFORMATION ON INSTALLING AND POWERING YOUR SAPPHIRE PLEASE  
REFER TO THE FULL USER MANUAL ON THE CD ROM.  
There are three Logic modes that you can select from. These different Logic settings determine  
how the Sapphire alerts you to fixed speed safety cameras. Logic 2 is the factory default setting.  
When Logic 2 is selected your unit will alert you both audibly and visually as you approach fixed  
safety cameras on your side of the carriageway only. For further information on alternative settings  
please refer to the user manual.  
External GPS extension antenna…………………………………………….........................£34.99  
Coiled power lead with cigarette lighter adaptor……………………….….......................... £12.95  
2m Straight power lead with cigarette lighter adaptor………………….……......................£12.95  
2m Straight hard wire lead with fuse…………………………………………....................... £12.95  
Windscreen mounting bracket…………………………………………………......................£24.95  
USB PC connection lead………………………………………………................................. £12.95  
1 – 3 Lighter socket extension………………………………………………........................... £7.99  
25ml anti-static LCD display cleaner & protector…………………………….........................£7.49  
Basic Operating Instructions  
1. Using the Sapphire for the first time  
After you have performed a download and installed your Sapphire perform the first start up. Make  
sure your vehicle is parked in as open a space as possible. The flip-up GPS antenna must have  
an unobstructed view of the sky above. Next turn the unit on by pressing and holding the  
Standby/Power switch for two seconds. The full colour TFT LCD display will briefly read ‘Snooper’,  
Logic #*, Mway*, City* or All* and finally ’Searching for Satellites...’ will flash along the bottom of  
the screen as the unit begins to search for satellite connection.  
Basic Troubleshooting  
6. Alert Patterns  
The unit cannot be switched on  
Fixed Speed Safety Cameras  
Check that the cigarette lighter adaptor is well inserted into the cigarette lighter socket and that the  
cigarette lighter socket is functioning properly. Check that the lighter socket is clean and free from  
debris. Also check that the fuse of the cigarette lighter adaptor is intact.  
As you approach a fixed speed safety camera the unit will begin to emit either a voice alert or your  
chosen audible alert at your preset alert distance. As you approach the fixed speed safety camera  
the ‘beeping’ will quicken. At the same time the display will indicate the type of location you are  
approaching, the speed limit at that location and will then begin to count down the distance in 50  
metre increments to that location. The unit will continue to alert you until you have passed the  
fixed speed safety camera.  
*FOR FURTHER INFORMATION OF THE MODE AND LOGIC SETTINGS PLEASE REFER  
TO SECTION 7 AND SECTION 10 OF THE FULL USER MANUAL ON THE CD ROM.  
The unit cannot acquire satellite connection  
Service under Warranty  
If your unit requires service within it’s standard 2 year warranty return your Snooper Sapphire, via  
special or recorded delivery and in suitable packaging to:  
Check that the Sapphire’s flip up GPS antenna has a clear view of the sky above.  
If this is the first time you have powered up your Sapphire please remember that the first ‘cold’ start  
may take up to 50 minutes to acquire sufficient satellite connection. Subsequent start up times will  
only take a couple of minutes if used regularly.  
Once the unit has acquired adequate satellite lock it will proceed to the Standby screen of your  
choice As soon as the standby screen is displayed your Sapphire is ready to use and will now  
automatically alert you of any locations stored in its database. A variety of audible and visual alert  
patterns are available. See ‘Features and Settings’ in the full user manual situated on the  
CD-ROM for how to further personalise your unit.  
Automute: When your device alerts you to a location, rather than continually beeping through  
the alert, it simply beeps at your selected volume for five seconds and then automatically mutes  
the sound to volume level 3 until you have passed or moved out of range of the speed camera.  
Note: This function is built into the unit and cannot be switched off.  
The Returns Department,  
Performance Products Limited,  
Cleaver House, Sarus Court, Manor Park, Cheshire WA7 1UL  
Quick Start Guide  
The satellite signal temporarily or permanently drops out  
This may happen temporarily in areas where there are a significant number of tall buildings or trees  
or whilst driving through a tunnel. The signal should only be lost for a few seconds and quickly  
reacquired.  
Enclose the following information:  
9. Auto Range  
As the GPS engine has never been used before, the first ‘Cold’ start could take from  
15 – 50 minutes to establish a satellite connection.Ssubsequent start ups should take only  
a matter of minutes.Please Note: If the unit is not used for some time the initial GPS start  
up may take longer than when the unit is used regularly.  
(a) Your name, address and a full description of the problem.  
(b) A telephone number where you can be reached during business hours.  
(c) Your units’ serial number.  
Auto-range is selected as the Factory Default setting. In this mode Sapphire simply selects the  
correct alert distance to each camera detected depending on the speed limit of the road the  
camera is situated on. The different alert distances are shown below.  
Check that the device has not moved and that the flip up GPS antenna still has a good clear view of  
the sky above.  
7
8
9
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Clock 65 792 User Guide
Ramsey Electronics Car Stereo System AF1 User Guide
RCA Conference Phone 16211370 User Guide
RCA Microcassette Recorder RP3536 User Guide
Rosewill Computer Keyboard RK 9000 User Guide
Runco Home Theater Screen SP 42 User Guide
Samsung Blu ray Player BDF5900 User Guide
Sanyo Flat Panel Television DP32D13 User Guide
Seagate Computer Drive ST9808211A User Guide
Sears Fitness Equipment 831159341 User Guide