LCD PROJECTOR LENS
MODEL NO. LNS-T03
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your
projector.
When installing or replacing the lens, make sure the Lens Model No. matches with to
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINET AND INSTALLATION PROCEDURES
Check the type of cabinet of your projector and follow the respective installation procedure
to install the lens correctly.
Type of the Cabinet (1) (See Page 2) Type of the Cabinet (2) (See Page 5)
For lens installation to the other models than above, contact your sales dealer.
1AA6P1P4097-- (IDLS)
Download from Www.Somanuals.com. All Manuals Search And Download.
{Type (1) Cabinet}
LENS REPLACEMENT AND INSTALLATION PROCEDURE
Remove 2 Screws A and Remove Lower Lens
B
Cover. Push part B and pull the Lower Lens
1
Cover down and remove it. (See Fig. 1.)
A
LOWER LENS
COVER
Fig-1
C
Remove 4 Screws C. Pull the Upper Lens Cover
toward front and remove it. (See Fig. 2.)
2
3
UPPER LENS
COVER
C
Fig-2
UPPER LENS
COVER
Remove 2 Screws D and Cover Plate from the
back of the Upper Lens Cover. (See Fig. 3.)
COVER PLATE
D
Fig-3
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
4
LENS LOCK
LEVER
LENS ATTACHMENT
Lens Attachment 01
POA-LNA-01
DRIVER INCLUDED
IN THE LENS PACKAGE
(610 303 8742)
LENS MOUNTING
BRACKET
Part No. (610 275 6029)
Fig-4
Fig-5
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
5
6
Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn
the lens part "B" to adjust FOCUS.
LENS LOCK
LENS LOCK RELEASE
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until it
is locked (clicked).
Grasp (unlock)
Lens Lock Lever
and pulling
upward.
Turn the lens part "A"
to adjust ZOOM.
A
B
Turn the lens part "B"
to adjust FOCUS.
Fig-6
Fig-7
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Put back the Upper Lens Cover to the projector and Fix the Upper Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Lower Lens Cover to the projector. Fix the Lower Cover with 2 Screws A.
(See Fig. 1.)
7
UPPER LENS
COVER
LOWER LENS
COVER
Fig-8
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
{Type (2) Cabinet}
LENS REPLACEMENT AND INSTALLATION PROCEDURE
A
Remove 2 Screws A and Remove Upper Lens
Cover. Push part B and pull the Upper Lens
1
Cover up and remove it. (See Fig. 1.)
UPPER LENS
COVER
B
Fig-1
C
Remove 4 Screws C. Pull the Lower Lens Cover
2
3
toward front and remove it. (See Fig. 2.)
LOWER LENS
COVER
C
Fig-2
D
Remove 2 Screws D and Cover Plate from the
back of the Upper Lens Cover. (See Fig. 3.)
UPPER LENS
COVER
COVER PLATE
Fig-3
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
4
LENS LOCK
LEVER
LENS ATTACHMENT
Lens Attachment 01
POA-LNA-01
DRIVER INCLUDED
IN THE LENS PACKAGE
(610 303 8742)
LENS MOUNTING
BRACKET
Part No. (610 275 6029)
Fig-4
Fig-5
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
5
6
Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn
the lens part "B" to adjust FOCUS.
LENS LOCK RELEASE
LENS LOCK
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until
it is locked (clicked).
Grasp (unlock)
Turn the lens part "A"
to adjust ZOOM.
Lens Lock Lever
and pulling
upward.
A
B
Turn the lens part "B"
to adjust FOCUS.
Fig-6
Fig-7
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Put back the Lower Lens Cover to the projector and Fix the Lower Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Upper Lens Cover to the projector. Fix the Upper Cover with 2 Screws A.
(See Fig. 1.)
7
UPPER LENS
COVER
LOWER LENS
COVER
Fig-8
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
|