Samsung Security Camera SNC B2331P User Guide

SNC-B2331(P)  
Network Camera  
User Manual  
imagine the possibilities  
Thanks you for purchasing this Samsung product.  
To receive a more complete service, please visit  
our website  
www.samsungsecurity.com  
RoHS compliant  
Our product complies with “The Restriction Of the use of certain Hazardous Substances in electrical  
and electronic equipment”, and we do not use the 6 hazardous materials- Cadmium (Cd), Lead  
(Pb), Mercury (Hg), Hexavalent Chromium (Cr+6), Poly Brominated Biphenyls (PBBs), Poly Brominated  
Diphenyl Ethers (PBDEs)- in our products.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or  
electric shock.  
8. If any unusual smells or smoke come from the unit, stop using the product. In such  
case, immediately disconnect the power source and contact the service center.  
Continued use in such a condition may cause fire or electric shock.  
9. If this product fails to operate normally, contact the nearest service center. Never  
disassemble or modify this product in any way. (SAMSUNG is not liable for problems  
caused by unauthorized modifications or attempted repair.)  
10. When cleaning, do not spray water directly onto parts of the product. Doing so may  
cause fire or electric shock  
11. Do not expose the product to the direct airflow from an air conditioner.  
Otherwise, it may cause moisture condensation inside the Clear Dome due to  
temperature difference between internal and external of the dome camera.  
12. If you install this product in a low-temp area such as inside a cold store, you must seal  
up the wiring pipe with silicon, so that the external air can not flow inside the housing.  
Otherwise, external high, humid air may flow inside the housing, pooling moisture or  
vapor inside the product due to a difference between internal and external temperature.  
English _3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
CAUTION  
1. Do not drop objects on the product or apply strong blows to it. Keep away from a  
location subject to excessive vibration or magnetic interference.  
2. Do not install in a location subject to high temperature (over 50°C), low temperature  
(below -10°C), or high humidity. Doing so may cause fire or electric shock.  
3. If you want to relocate the already installed product, be sure to turn off the power and  
then move or reinstall it.  
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do  
so may cause fire or damage to the product.  
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.  
6. Install it in a place with good ventilation.  
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this  
may damage the CCD image sensor.  
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with  
liquids, such as vases, shall be placed on the apparatus.  
9. The Mains plug is used as a disconnect device and shall stay readily operable at any  
time.  
10. When using the camera outdoors, moisture may occur inside the camera due  
to temperature difference between indoors and outdoors. For this reason, it is  
recommended to install the camera indoors. For outdoor use, use the camera with built-  
in fan and heater.  
4_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions :  
1) This device may not cause harmful interference, and  
2) This device must accept any interference received including interference that may cause  
undesired operation.  
Caution  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference when the equipment is operated in a  
commercial environment.  
This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area  
is likely to cause harmful interference in which case the user will be required to correct  
the interference at his own expense.  
IC Compliance Notice  
This Class A digital apparatus meets all requirements of the Canadian  
Interference.-Causing Equipment Regulations of ICES-003.  
English _5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
IMPORTANT SAFETY INSTRUCTIONS  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturers  
instructions.  
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus  
(including amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or grounding-type plug.  
A polarized plug has two blades with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide blade or the third prong is  
provided for your safety. If the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched particularly at plugs,  
convenience receptacles, and the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table specified by  
the manufacturer, or sold with the apparatus. When a cart is used,  
use caution when moving the cart/apparatus combination to avoid  
injury from tip-over.  
13. Unplug this apparatus during lightning storms or when unused for  
long periods of time.  
14. Refer all servicing to qualified service personnel. Servicing is required when the  
apparatus has been damaged in any way, such as powersupply cord or plug is  
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus  
has been exposed to rain or moisture, does not operate normally, or has been dropped.  
Apparatus shall not be exposed to dripping or splashing and no objects  
filled with liquids, such as vases, shall be placed on the apparatus  
6_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
6
9
important safety instructions  
Product Features  
OVERVIEW  
9
10  
11  
Recommended PC Specifications  
What’s Included  
At a Glance  
2
13  
15  
Mounting the lens  
Connecting with other Device  
INSTALLATION & CONNECTION  
13  
17  
How to use the keyboard  
controller  
CAMERA SETUP  
18  
18  
19  
23  
24  
25  
25  
Main Menu  
Profile  
Camera Setup  
Privacy Zone  
Others  
17  
System Info  
Language  
26  
27  
28  
29  
Connecting the Camera to an  
IP Router With The xDSL/Cable  
Modem  
Connecting the Camera to  
an IP Router With Local Area  
Networking  
Connecting the Camera Directly  
to a DHCP-Based xDSL/Cable  
Modem  
Connecting the Camera Directly  
to Local Area Networking  
IP Address Setup  
NETWORK CONNECTION  
AND SETUP  
26  
30  
31  
34  
35  
Static IP Setup  
Dynamic IP Setup  
Port Range Forward (Port  
Mapping) Setup  
35  
36  
Connecting to the camera from a  
shared local PC  
Connecting to the camera from a  
remote PC via the Internet  
English _7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
37  
38  
39  
40  
41  
Connecting to the camera  
Login  
Installing ActiveX  
Using the Live Screen  
Backup  
WEB VIEWER  
37  
43  
44  
48  
51  
52  
57  
Accessing the Setup screen  
Default Setup  
System Setup  
Overlay Setup  
Event Setup  
SETUP SCREEN  
43  
APPENDIX  
59  
Network Setup  
59  
60  
61  
65  
71  
77  
Profile  
Terminology  
Specifications  
Frame Rate (NTSC)  
Frame Rate (PAL)  
Troubleshooting  
8_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT FEATURES  
y
Support various communication protocols  
Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various  
internet protocols such as ARP, HTTP, HTTPS and DHCP.  
y
y
y
Web Browser-based Monitoring  
Using the Internet web browser to display the image in a local network environment.  
Automatic Local IP Setup  
Even a network novice can install it with minimum operations.  
Alarm  
If the camera equipped with an alarm sensor senses any motion, it will send a notification  
to a user FTP/email account (SMTP) or send the corresponding signal to the Alarm Out  
terminal.  
y
Motion Detection  
If the camera with a specified motion area detects a motion in that area, it will send a  
notification to a user FTP/email account (SMTP) or send the corresponding signal to the Alarm  
Out terminal.  
RECOMMENDED PC SPECIFICATIONS  
y
y
y
y
y
y
y
y
CPU : Pentium4 / 2.4GHz or higher  
Operating System : Windows XP(Service Pack2, Service Pack3) / Windows Vista  
Resolution : 1024X768 pixels or higher  
RAM : 512MB or higher  
Web Browser : Internet Explorer 6.0 or higher  
Video Card : Radeon, Nvidia  
Video Memory: 128MB  
DirectX 8.1 or higher  
Compatible IP Routers  
y
y
y
Linksys  
D-Link  
Netgear  
Compatible PoE Switches  
y
y
y
Linksys SRW224G4P  
D-Link DES-1316  
SMC SMCPWR-INJ3  
English _9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
WHAT’S INCLUDED  
Please check if your camera and accessories are all included in the product package.  
Camera Holder (Mount)  
& Screws (2EA)  
Camera  
C Mount Adaptor  
User Manual/  
IP INSTALLER CD  
User Manual  
Lens Options  
CS Lens  
C Lens  
10_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AT A GLANCE  
Front Side  
Item  
Description  
Camera Holder  
(Mount) Holes  
Used when you mount the camera onto the bracket by fixing the camera  
holder (mount) adaptor with the bracket.  
Auto Iris Lens  
(Optional)  
Installed on the lens adaptor.  
Auto Iris Lens  
Connector  
Used to supply power and output signal to control the iris of the lens.  
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied  
ethanol.  
M
English _11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
overview  
Rear Side  
SYSTEM POWER  
RESET  
VIDEO  
NETWORK  
1
2
3
4
5
1,2 : ALARM IN 1,2  
: GND  
4,5 : ALARM OUT 1,2  
ACT  
LINK  
GND  
AC 24V  
DC 12V  
3
Item  
Description  
Video Out Port  
Video signal output port connected to the monitor.  
ON: The camera is turned on and connected to the network  
properly.  
SYSTEM  
Blinking: During DDNS setup, or in case of setup failure, or  
in a state of unstable network connection  
System, Power  
Indicators  
OFF: When the system is rebooting, or turned off  
ON: While the power is on  
OFF: If the power is off  
POWER  
Resets the camera settings to the default. Press and hold it for about 3  
seconds to turn off the system indicator and restart the system.  
Reset Button  
Power Port  
Used to plug the power cable.  
Network Port  
Used to connect to the Network cable.  
ALARM IN  
Used to connect the alarm input signal.  
1,2  
I/O Port  
GND  
Used for earth-grounding.  
ALARM OUT  
1,2  
Used to connect the alarm output signal.  
12_ overview  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation & connection  
MOUNTING THE LENS  
Disconnect the power before proceeding.  
Mounting the CS lens  
Turn the optional CS lens clockwise to insert it.  
CS Lens  
Mounting the C lens  
Turn the C mount adaptor clockwise to insert it and do the same with the C lens.  
C Lens  
English _13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation & connection  
Connecting the Auto Iris Lens connector  
Insert the lens connector into the corresponding hole of the camera.  
Focusing  
Turn the lens left or right to control the zoom and focus the lens so that you can view a clear,  
sharp object.  
14_ installation & connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING WITH OTHER DEVICE  
Monitor  
SYSTEM POWER  
RESET  
VIDEO  
NETWORK  
1
2
3
4
5
1,2  
3
4,5  
:
:
:
ALARM IN 1,2  
GND  
ALARM OUT 1,2  
ACT  
LINK  
GND  
AC 2V  
DC 1V  
Power  
Network  
Connecting to the monitor  
Connect the [VIDEO] port of the camera to the video input port of the monitor.  
Network Connection  
Connect the Network cable to the local network or to the Internet.  
Power Supply  
Use the screwdriver to connect each line of the power cable to the corresponding port of  
the camera.  
Be careful not to reverse the polarity when you connect the power cable.  
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.  
J
English _15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installation & connection  
Connecting to the I/O port box  
Connect the Alarm I/O signal to the corresponding port of the rear port box.  
1 2 3 4 5  
SYSTEM POWER  
VIDEO  
RESET  
NETWORK  
1
2
3
4
5
1,2 : ALARM IN 1,2  
: GND  
4,5 : ALARM OUT 1,2  
1,2  
3
4,5  
:
:
:
ALARM IN 1,2  
GND  
ALARM OUT 1,2  
ACT  
LINK  
GND  
AC 24V  
DC 12V  
3
y
y
y
ALARM IN 1, 2 : Used to connect the alarm input signal.  
GND : Used for earth-grounding.  
ALARM OUT 1, 2 : Used to connect the alarm output signal.  
Alarm I/O Wiring Diagram  
ALARM IN 1  
1
ALARM IN 2  
2
GND  
3
External Relay  
ALARM OUT 1  
4
External Relay  
ALARM OUT 2  
5
16_ installation & connection  
Download from Www.Somanuals.com. All Manuals Search And Download.  
camera setup  
You can configure the camera settings using the Web Viewer.  
For accessing the Web Viewer, refer to "Network Connection and Setup". (page 26)  
M
HOW TO USE THE KEYBOARD CONTROLLER  
Follow the steps below if you run the Web Viewer for setting the menus.  
1. Launch the Web Viewer.  
2. From the [Camera OSD] menu in the left  
pane, click [Menu].  
The <MAIN MENU> screen appears.  
3. Click the Up/Down (▲▼) buttons to move to a  
desired item.  
4. Click the four direction (▲▼◄ ►) buttons to navigate through the menu items.  
5. To change the value of a selected item, click the Left/Right (◄ ►) buttons.  
6. Click [  
].  
Your changes will be applied.  
: Exits the menu setup screen.  
Before exiting the setup screen, select [SAVE] to save your settings, or [QUIT] to  
cancel them.  
: Saves your settings and returns to the previous screen.  
: Returns to the main menu.  
: Use this icon if you want to save your settings after you specified the mask area and  
privacy area, etc.  
Once you saved your settings, the changes remain intact even if you select [QUIT] on  
exit.  
: Use this icon if you want to delete a mask, or privacy area, etc.  
Once you deleted your settings, the deletions remain valid even if you select [QUIT] on  
exit.  
: This arrow appears next to a menu that contains sub items.  
For the items with the "*" mark on the right, You can get help from "Terminology". (page 60)  
English _17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
camera setup  
MAIN MENU  
You can configure the camera settings to your preference.  
y
PROFILE  
** MAIN MENU **  
PROFILE  
CAMERRA SET  
PRIVACY ZONE  
OTHER SET  
SYSTEM INFO  
LANGUAGE  
You can select a mode that is appropriate to the  
camera installation environment.  
CAMERA SET  
Configure the camera functions and settings.  
PRIVACY ZONE  
You can configure the privacy settings.  
OTHER SET  
y
y
y
You can configure more settings including  
FACTORY DEFAULTS.  
y
y
SYSTEM INFO  
Shows the camera version and type.  
LANGUAGE  
Select a preferred one from the supported languages.  
PROFILE  
You can select one from the pre-determined modes as appropriate to your specific camera installation  
environment.  
Your selection on each item in PROFILE will affect all other settings of the camera. For the  
setting, refer to "PROFILE". (page 59)  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
y
y
y
STANDARD  
Automatically optimizes the camera settings to  
the normal environment.  
PROFILE  
*STANDARD  
ITS  
BACKLLIGHT  
DAY/NIGHT  
GAMING  
ITS  
This setting enables you to analyze the traffic  
situation and take the traffic information at a glance.  
CUSTOM  
BACKLIGHT  
This setting enables you to view a sharp background  
and object even in a severe backlight scene.  
y
y
DAY/NIGHT  
Automatically optimizes the camera settings to the day and night scene.  
GAMING  
This automatically configures the settings so that you can work in a stable illumination  
condition as indoors.  
y
CUSTOM  
Your change to any of the PROFILE settings will switch the display to CUSTOM.  
18_ camera setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAMERA SETUP  
You can configure the general settings of the camera module.  
Use the four direction (▲▼◄ ►) buttons to select a desired item.  
CAMERA ID  
Provide the ID and position for a camera that displays on the screen.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <CAMERA SET> - <CAMERA ID>.  
CAMERA ID  
ABCDEFGGHIJKLMNNOPQRSTTUUVWXYZO  
_
123456789 : ? +*()/  
2. Use the four direction (▲▼◄ ►) buttons to  
select a desired character.  
In the lower input box of the screen, the  
selected character will be entered.  
You can enter up to 54 characters including alphabets,  
numbers and special characters.  
SPSP  
- - - - - - - - - - - - - - - - - - - - - - - - -  
- - - - - - - - - - - - - - - - - - - - - - - - -  
LOCATION  
3. When done, continue to select <LOCATION>  
to specify the display position of the camera ID.  
IRIS  
You can set the iris to control the intensity of radiation incoming to the camera.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <CAMERA SET> - <IRIS>.  
ALC  
2. Use the left/right (◄ ►) buttons to select either  
<ALC> or <ELC>.  
LENS  
LEVEL  
BACKLLIGHT  
DC  
---- ----  
[
]
00  
I
y
ALC : Controls the luminance automatically.  
LENS : Select a lens to use.  
ELC : Controls the level electronically.  
OFF  
-
y
-
-
LEVEL : Select an overall brightness level.  
BACKLIGHT : Specify an area to  
compensate for the backlight.  
With <AREA> set to <USER>, you can specify the position and size.  
If the iris is set to <ALC>, fixing the iris is your priority when you adjust AE and the shutter speed.  
M
English _19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
camera setup  
MOTION  
CAMERA SET  
You can specify a level of AGC for controlling the  
camera motion.  
Select F.FAST if you want to monitor a very fast  
moving object in a low contrast scene, and S.SLOW  
if monitoring a very slow moving, inanimate object in  
the same condition.  
CAMERA ID  
IRIS  
MOTION  
DNR  
SHUTTER  
SENS-UP  
FLICKERLESS  
XDR  
ON  
ALC  
(F.FAST)---  
MID  
OFF  
AUTO X4  
OFF  
MID  
OFF  
DIS  
As long as DAY/NIGHT is set to AUTO, the  
<MOTION> menu is not available.  
DNR  
Reduces the noise on the screen.  
This is useful, especially for a noisy screen.  
Set it to <USER>, you can specify the level.  
DAY/NIGHT  
WHITE BAL  
DIGITAL ZOOM  
DETAIL  
AUTO  
OFF  
[
]
2
AGC COLOR SUP  
REVERSE  
POSI/NEGA  
PIP  
MID  
OFF  
+
SHUTTER  
OFF  
The SHUTTER menu is used to set the fixed fast  
electronic shutter or auto fast electronic shutter.  
SENS-UP  
If the brightness of the video signal is too low, the Slow Shutter function will be activated.  
Slow Shutter can collect the individual max frame rate to adjust the setting.  
FLICKERLESS  
If set to <ON>, the shutter speed will be fixed to 1/100 second. This will prevent possible  
screen distortion due to a mismatch between the vertical sync frequency and the blinking  
frequency of the lighting.  
If IRIS is set to ELC / SHUTTER to AUTO, FIX, EXT mode / SENSE UP to FIX / AGC to FIX, the <DIS> menu  
will be disabled.  
XDR  
This will correct a brightness difference between different scenes for the optimal visibility.  
The higher the value is, the higher the correction level is.  
DIS  
Automatically compensates for the flicker on the screen.  
If set to <ON>, the image will be enlarged with digital zoom as much area as  
compensated.  
20_ camera setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DAY/NIGHT  
You can specify a recording mode according to the scene.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <CAMERA SET> - <DAY/NIGHT>.  
AUTO  
2. Select a screen transition mode according to the  
illumination, and set options as appropriate.  
BURST  
DAYNIGHT  
OFF  
y
y
DAY : Fixed to DAY mode, regardless of the  
scene.  
BRIGHTTNESS  
DWELL TIME  
NIGHTDAY  
BRIGHTTNESS  
DWELL TIME  
MID  
2S  
NIGHT : Fixed to NIGHT mode, regardless  
of the scene.  
MID  
5S  
1 2  
MASK AREA  
If BURST is set to <ON>, the burst signal will  
output.  
y
y
AUTO : According to the luminance, this will  
switch DAY to NIGHT mode, or vice versa.  
MASK AREA  
DAYNIGHT / NIGHTDAY : If set to  
<AUTO>, you can specify the brightness  
level triggering the mode switch between  
DAY and NIGHT as well as the interval.  
<SIZE>  
<LOCATION>  
y
MASK AREA : If there exists a bright spot  
light source in a night scene, you can specify  
the size and position as needed.  
Any excessively bright area in a night scene  
will be masked.  
WHITE BAL  
If you need to adjust the screen brightness, use the WHITE BALANCE function.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <CAMERA SET> - <WHITE BAL>.  
WHITE BAL  
2. Select a mode where you set the balance.  
DAY/NIGHT  
MODE  
DAY  
ATW2  
y
DAY : You can set the RED, and BLUE value  
in DAY mode.  
[
[
]
]
---- ----  
RED  
BLUE  
00  
00  
I
---- ----  
I
y
NIGHT : You can adjust the <WHITE BAL>  
according to the ambient luminance.  
English _21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
camera setup  
3. According to the specified recording mode,  
select a WHITE BAL mode with necessary  
options.  
WHITE BAL  
DAY/NIGHT  
NIGHT  
MID  
AWC  
I
I
BRIGHTNESS  
MODE  
y
BRIGHTNESS : Specify a brightness level  
triggering the switch from DAY to NIGHT  
mode.  
[
[
[
[
]
]
---- ----  
RED  
BLUE  
R-GAIN  
B-GAIN  
00  
00  
---- ----  
]
]
0040  
0133  
y
MODE : According to the selected mode, you  
can adjust the RED and BLUE color level.  
-
-
RED : Adjust the strength of the red color.  
BLUE : Adjust the strength of the blue  
color.  
-
R-GAIN/B-GAIN : Specify the current color temperature manually.  
You can set the R-GAIN, and B-GAIN value only in AWC mode.  
DIGITAL ZOOM  
You can set the digital zoom factor and position.  
When the zoom factor and position are defined, the digital zoom function will operate.  
If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS  
function will be disabled.  
DETAIL  
You can adjust the vertical and horizontal sharpness, respectively.  
AGC COLOR SUP  
This will adjust the color scheme according to the AGC value.  
REVERSE  
This will reverse the signal left to right, top to bottom, or a combination of the preceding.  
POSI/NEGA  
This will display the video brightness signal either normally or reversely.  
PIP  
You can view a main image with a sub image on the same screen.  
22_ camera setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRIVACY ZONE  
You can set up to 12 privacy zones that will be hided for privacy of the subject when recording.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
ZONE SETUP  
1. Select <MAIN MENU> - <PRIVACY ZONE>.  
PRIVACY ZONE  
2. Use the four direction (▲▼◄ ►) buttons to  
select a desired number.  
The Zone setup screen appears.  
1
7
2
8
3
9
4
5
6
10 11 12  
PRIVACY SET  
STYLE  
ON  
MOSAIC1  
3. Select the <PIXEL LEVEL>.  
Specify the pixel unit level for the POSITION set-  
ting.  
PRIVACY ZONE SET 1  
[
]
4
PIXEL LEVEL  
<POINT>  
4. Select <POINT>.  
<POSITION>  
You will see dots on the screen.  
5. Use the four direction (▲▼◄ ►) buttons to specify  
the position for each of the four dots.  
6. Select <POSITION> and use the four direction  
(
▲▼◄ ►) buttons to specify the position for each  
of the four dots.  
7. Save the changes and move to the previous screen and select the <STYLE>.  
Select <COLOR> and pick a desired color.  
Setting one or more privacy zone and enabling privacy function will disable the PIP function.  
M
English _23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
camera setup  
OTHERS  
You can reset the camera, or select the OSD font color to your preference.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
FACTORY DEFAULT  
1. Select <MAIN MENU> - <OTHER SET>  
OTHER SET  
- <FACTORY DEFAULTS>.  
The FACTORY DEFAULTS setup screen  
appears.  
FACTORY DEFAULTS  
OSD COLOR  
BW  
2. Select <OK>.  
All the settings will be restored to the factory  
default.  
However, the language setting will not be  
restored.  
FACTORY DEFAULTS  
OK  
CANCEL  
OSD COLOR  
You can set the font color of the user interface.  
24_ camera setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SYSTEM INFO  
You can check the system information.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <MAIN MENU> - <SYSTEM INFO>.  
SYSTEM INFO  
2. The current system information is displayed.  
_
_
P
TYPE  
3
IPB  
CAMERAA VER.  
v1.00__090724  
The camera type may different, depend on the video  
signal.  
M
LANGUAGE  
You can select a language to your preference.  
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 17)  
1. Select <MAIN MENU> - <LANGUAGE>.  
LANGUAGE  
2. Select your preferred language using the  
*ENGLISH  
FRANÇAIS  
DEUTSCH  
ESPAÑOL  
ITALIANO  
up/down (▲▼) buttons.  
Supported language may different.  
M
English _25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
You can set up the network settings according to your network configurations.  
CONNECTING THE CAMERA TO AN IP ROUTER WITH THE  
XDSL/CABLE MODEM  
This is for a small network environment such as homes, SOHO and ordinary shops.  
SNC-B2331  
INTERNET  
Cable Modem  
xDSL or  
Cable Modem  
xDSL or  
IP Router  
External Remote PC  
SNC-B2331  
Local PC  
DDNS Server  
(Data Center, KOREA)  
Configuring the network settings of the local PC connected to an  
IP router  
Configuring the network settings of the local PC connected to an IP router, follow the  
instructions below.  
y
Select : <Network Neighborhood> <Properties> <Local Area Connection>  
<Properties> <General> <Internet Protocol (TCP/IP)> <Properties>  
<Obtain an IP address automatically> or <Use the following IP address>.  
y
Follow the instructions below if you select <Use the following IP address>:  
ex1) If the address (LAN IP) of the IP router is 192.168.1.1  
IP address: 192.168.1.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.1.1  
ex2) If the address (LAN IP) of the IP router is 192.168.0.1  
IP address: 192.168.0.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.0.1  
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1  
IP address: 192.168.xxx.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.xxx.1  
For the address of the IP router, refer to the product’s documentation.  
M
26_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking if the IP router is connected to the xDSL/Cable modem properly  
Select <Status> from the Settings menu of the IP Router  
y
If it is properly connected, <IP Address>, <Subnet Mask> and <Gateway>  
provided by your ISP are displayed. Please remember these values because they  
are required so that an external remote computer of the IP router connects to the  
camera. However, note that certain ISPs change the settings of <IP Address>,  
<Subnet Mask> and <Gateway> on a regular basis  
y
If the IP router is not properly connected, press the [Connect] button to try to recon-  
nect or check if the settings of the IP router are correct.  
CONNECTING THE CAMERA TO AN IP ROUTER WITH  
LOCAL AREA NETWORKING  
This is for a large network environment such as corporate office, building, public office and factory.  
SNC-B2331  
Switch  
INTERNET  
HUB  
IP Router  
External Remote PC  
Firewall  
SNC-B2331  
Local PC  
DDNS Server  
(Data Center, KOREA)  
Local PC  
Configuring the network settings of the local PC connected to an  
IP router  
Configuring the network settings of the local PC connected to an IP router, follow the  
instructions below.  
y
Select : <Network Neighborhood> <Properties> <Local Area Connection>  
<Properties> <General> <Internet Protocol (TCP/IP)> <Properties>  
<Obtain an IP address automatically> or <Use the following IP address>.  
y
Follow the instructions below if you select <Use the following IP address>:  
ex1) If the address (LAN IP) of the IP router is 192.168.1.1  
IP address: 192.168.1.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.1.1  
ex2) If the address (LAN IP) of the IP router is 192.168.0.1  
IP address: 192.168.0.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.0.1  
English _27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1  
IP address: 192.168.xxx.100  
Subnet Mask: 255.255.255.0  
Default Gateway: 192.168.xxx.1  
For the address of the IP router, refer to the product’s documentation.  
M
CONNECTING THE CAMERA DIRECTLY TO A DHCP-  
BASED XDSL/CABLE MODEM  
INTERNET  
xDSL or  
CableModem  
External Remote PC  
SNC-B2331  
DDNS Server  
(Data Center, KOREA)  
Setting the IP Router  
This is enabled for a modem using DHCP.  
1. Set the Static or Dynamic IP address. (pages 31~36)  
2. Launch an Internet browser on the local PC connected to the IP Router.  
3. Enter the IP Routers address in the address bar of the browser.  
ex) http://192.168.1.1, http://192.168.0.1  
or http://192.168.xxx.1  
For the DDNS URL address, refer to "To check the DDNS address". (page 38)  
4. When the IP Router is connected, the login window appears and prompts you to  
enter the password.  
For the login IP and the password, refer to the IP router’s documentation.  
5. When done, you will see the setup window of the IP router. In the setup menu,  
select “Automatic Configuration-DHCP” for Internet Connection Type.  
For the menu location of Internet Connection Type or DHCP selection, refer to the IP router’s  
documentation.  
6. When done, click the [Save] or [Apply] button to save the settings.  
28_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA  
NETWORKING  
Connecting to the camera from a local PC in the LAN  
1. Launch an Internet browser on the local PC.  
2. Enter the IP address of the camera in the address bar of the browser.  
SNC-B2331  
Switch  
HUB  
INTERNET  
External Remote PC  
SNC-B2331  
F
irewall  
Local PC  
D
D
N
S
S
erver  
(DataCenter,KOREA)  
A remote PC in an external Internet out of the LAN network may not be able to connect to the  
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.  
In this case, to resolve the problem, contact your network administrator.  
M
English _29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
IP ADDRESS SETUP  
Buttons used in IP Installer  
Item  
Description  
Model name of the connected camera.  
Device Name  
Click the column to sort the list by model name.  
However, search will be stopped if clicked during the search.  
Displays either <Static> or <Dynamic> for the current network connection  
status.  
Mode  
Ethernet address for the connected camera.  
Click the column to sort the list by Ethernet address.  
However, search will be stopped if clicked during the search.  
MAC(Ethernet)  
Address  
IP address.  
Click the column to sort the list by IP address.  
However, search will be stopped if clicked during the search.  
The factory default is "192.168.1.200".  
IP Address  
Network setting for the camera.  
Protocol  
The factory default is "IPv4".  
Cameras with the IPv6 setting will be displayed "IPv6".  
UPnP Status  
This function is not currently implemented.  
30_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DDNS URL address enabling access from the external Internet.  
However, this will be replaced with the <IP Address> of the camera if  
DDNS registration has failed.  
URL  
IPv4  
IPv6  
Scans for cameras with the IPv4 setting.  
Scans for cameras with the IPv6 setting.  
Scans for cameras that are currently connected to the network.  
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.  
Search  
Auto Set  
Manual Set  
Exit  
<IP Installer> will automatically configure the network settings for you.  
You should configure the network settings manually.  
Exits the IP Installer program.  
STATIC IP SETUP  
Manual Network Setup  
Run <IP Installer.exe> to display the camera search list.  
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.  
For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not  
support this function.  
M
1. Select a camera in the search list.  
Find the MAC (Ethernet) address labeled  
on the rear of the camera.  
Both the [Auto Set] and [Manual Set]  
buttons will be activated.  
2. Click [Manual Set].  
The MANUAL SET dialog appears.  
The default values of <IP Address>,  
<Subnet Mask>, <Gateway>, and <HTTP Port> of the camera will be displayed.  
The default <PASSWORD> is 4321.  
3. In the <ADDRESS> pane, provide the  
necessary information.  
MAC (Ethernet) Address : The MAC  
(Ethernet) address of the applicable  
camera will be set automatically so you  
don't need to input it manually.  
English _31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
If using an IP router :  
y
IP Address : Enter an address falling in  
the IP range provided by the IP router.  
ex) 192.168.1.2~254,  
192.168.0.2~254,  
192.168.XXX.2~254  
y
y
Subnet Mask : The <Subnet Mask> of  
the IP router will be the <Subnet Mask>  
of the camera.  
Gateway : The <Local IP Address> of  
the IP router will be the <Gateway> of the camera.  
If not using an IP router :  
For setting <IP Address>, <Subnet Mask>, and <Gateway>, contact your network  
administrator.  
The values of Device, TCP, UDP, Upload, and Multicast ports can not be changed manually, and  
will be adjusted according to the HTTP port value.  
M
4. In the <PORT> pane, provide  
necessary information.  
y
HTTP Port : Used to access the  
camera using the Internet browser,  
defaulted to 80. Use the spin button  
to change the HTTP Port value. The  
start value of the port is 80, and  
increases or decreases by 6 like  
10000, 10006, 10012.  
y
y
Device Port : Used to control the video signal transfer, defaulted to 60001(TCP).  
TCP Port : Video signal transfer port using TCP protocols, defaulted to  
60002(TCP).  
y
UDP Port : Video signal transfer port using the UDP Unicast method, defaulted to  
60003(UDP).  
y
y
Upload Port : Used to upgrade the software firmware, defaulted to 60004(TCP).  
Multicast Port : Video signal transfer port using the UDP Multicast method,  
defaulted to 60005(UDP).  
5. Enter the password.  
This is the login password for the "root" user who accesses the camera.  
The default password is "4321".  
32_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Click [OK].  
Manual network setup will be completed.  
7. When the manual setup including <IP> is completed, the camera will restart.  
If the IP router has more than one camera connected  
Configure the IP related settings and the Port related settings distinctly with each other.  
Category  
IP Address  
Subnet Mask  
Gateway  
Camera #1  
Camera #2  
192.168.1.200  
255.255.255.0  
192.168.1.1  
192.168.1.201  
255.255.255.0  
192.168.1.1  
IP related settings  
HTTP Port  
Device Port  
TCP Port  
UDP Port  
Upload Port  
Multicast Port  
80  
10000  
10001  
10002  
10003  
10004  
10005  
60001  
60002  
60003  
60004  
60005  
Port related settings  
If the <HTTP Port> is set other than 80, you must provide the <PORT> number in the address  
bar of the Internet browser before you can access the camera.  
ex) http://IP address : HTTP Port  
M
http://192.168.1.201:10000  
Auto Network Setup  
Run <IP Installer.exe> to display the camera search list.  
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.  
For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not  
support this function.  
M
1. Select a camera in the search list.  
Find the MAC (Ethernet) address labeled  
on the rear of the camera.  
Both the [Auto Set] and [Manual Set]  
buttons will be activated.  
2. Click [Auto Set].  
The AUTO SET dialog appears.  
The <IP Address>, <Subnet Mask>,  
and <Gateway> will be set automatically.  
English _33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
3. Enter the password.  
This is the login password for the "root"  
user who accesses the camera.  
The default password is "4321".  
4. Click [OK].  
Auto network setup will be completed.  
5. The camera will automatically complete  
the network setting and restart.  
DYNAMIC IP SETUP  
Dynamic IP Environment Setup  
y
Example of the dynamic IP environment  
-
-
-
If an IP router, with cameras connected, is assigned an IP address by the DHCP  
server  
If connecting the camera directly to the xDSL or cable modem using the DHCP  
protocols  
If IPs are assigned by the internal DHCP server via the LAN  
Checking the dynamic IP  
1. From a local PC, run <IP Installer>  
to display a list of cameras that are  
assigned <Dynamic IP>.  
2. Select a camera in the list, and click  
[Manual Set] to check the <Dynamic  
IP> of the camera.  
If you uncheck <DHCP>, you can  
change <IP> or <PORT> to <STATIC>.  
34_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PORT RANGE FORWARD (PORT MAPPING) SETUP  
If you have installed an IP router with a camera connected, you must set the port range  
forwarding on the IP router so that a remote PC can access the camera in it.  
Manual Port Range Forwarding  
1. From the Setup menu of the IP router,  
select <Applications & Gaming> -  
<Port Range Forward>.  
For setting the port range forward for  
a third-party IP router, refer to the user  
guide of that IP router.  
2. Select <TCP> and <UDP Port> for  
each connected camera to the IP  
router.  
Each port number for the IP router  
should match that specified in <Basic>  
- <IP> from the camera's Setup menu.  
3. When done, click [Save Settings].  
Your settings will be saved.  
CONNECTING TO THE CAMERA FROM A SHARED LOCAL  
PC  
1. Launch <IP Installer>.  
It will scan for connected cameras and  
display a list of them.  
2. Double-click a camera to access.  
The Internet browser starts and  
connects to the camera.  
You can also access the camera in such way you type the IP address of the found camera in the  
address bar of the Internet browser.  
M
English _35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
network connection and setup  
CONNECTING TO THE CAMERA FROM A REMOTE PC VIA  
THE INTERNET  
As a remote PC can not directly access <IP Installer>, you should access the camera in the IP  
router network using DDNS URL of the camera.  
1. Before you can access a camera in the IP router network, you should have set the  
port range forward for the IP router.  
2. From the remote PC, launch the Internet browser and type the DDNS URL address  
of the camera, or the IP address of the IP router in the address bar.  
ex) http://mfffe42.websamsung.net  
For the DDNS URL address, refer to "To check the DDNS address". (page 38)  
36_ network connection and setup  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
CONNECTING TO THE CAMERA  
Normally, you would  
1. Launch the Internet browser.  
2. Type the IP address of the camera in  
the address bar.  
ex) IP address (IPv4) : 192.168.1.200  
http://192.168.1.200  
- the Login dialog should appear.  
IP address (IPv6) : 2001:230:abcd:  
ffff:0000:0000:ffff:1111  
http://[2001:230:abcd:ffff:0000  
:0000:ffff:1111]  
If the HTTP port is other than 80  
1. Launch the Internet browser.  
2. Type the IP address and HTTP port number of the camera in the address bar.  
ex) IP address : 192.168.1.200:Port number(10000) http://192.168.1.200:10000  
- the Login dialog should appear.  
Using URL  
1. Launch the Internet browser.  
2. Type the DDNS URL of the camera in the address bar.  
ex) URL address : http://mfffe42.websamsung.net  
- the Login dialog should appear.  
Connecting via URL (If the HTTP port is other than 80)  
1. Launch the Internet browser.  
2. Type the DDNS URL and HTTP port number of the camera in the address bar.  
ex) URL address : http://mfffe42.websamsung.net:Port number(10000)  
http://mfffe42.websamsung.net:10000  
- the Login dialog should appear.  
English _37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
To check the DDNS address  
The DDNS address consists of: <one of the lower-case letters: c, m, p> + <the last 6 digits  
of the MAC (Ethernet) address> + <websamsung.net>  
The small letter will be <c> if the first 6 digits of the MAC (Ethernet) address is <00:00:f0>,  
or <m> if they are <00:16:6c>, or <p> for <00:68:36>.  
ex) - If the MAC (Ethernet) address is 00:00:f0:ff:fe:42: c + fffe42 + websamsung.net =  
cfffe42.websamsung.net  
-
If the MAC (Ethernet) address is 00:16:6c:ff:fe:42: m + fffe42 +websamsung.net =  
mfffe42.websamsung.net  
-
If the MAC (Ethernet) address is 00:68:36:ff:fe:42: p + fffe42 +websamsung.net =  
pfffe42.websamsung.net  
The above mentioned addresses are simply examples; do not use any of these for connecting  
purposes.  
J
LOGIN  
The default user ID is "root", and the default password is "4321".  
1. Enter "root" in the <User Name> input  
box.  
2. Enter "4321" in the <Password> input  
box.  
If the password is changed, enter the  
changed password instead.  
3. Click [OK].  
If you have logged in successfully, you  
will the Live Viewer screen.  
For security purposes, ensure that you change the password in <Basic> - <User>.  
The administrator ID, "root", is fixed and can not be changed.  
M
J
If you check the "Save this password in your password list" option when your input is done, you  
will be logged in automatically without being prompted to enter the login information from next time on.  
For this, your computer has installed DirectX 8.1 or later.  
You can get a free download of the latest DirectX from http://www.microsoft.com/download.  
If you are using Internet Explorer 7.0 or 8.0 as the default web browser, you can view the best  
quality image with a screen ratio of 100%. Reducing the ratio may cut the image on the borders.  
38_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING ACTIVEX  
If connecting to a camera for the first time, you will see the installation message. Then, install the  
required ActiveX to access the camera and control the video from it in real time.  
For Windows XP Service Pack 2 users  
1. Click the installation message that pops  
up when you first access the camera.  
2. Click <Install ActiveX Control...>.  
3. The security warning popup appears,  
click [Install].  
4. When the required ActiveX is installed  
properly after your access to the camera,  
the Live screen should appear.  
For normal installation, set the Block  
Popup setting as follows:  
Internet Explorer Tools Block  
Popup Always allow popups from  
the current site(A)  
J
English _39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
USING THE LIVE SCREEN  
Item  
Description  
Setup  
Move to the Setup screen.  
About  
You can check the firmware version, serial number and manufacturer information.  
Resets the Alarm icon. (the Alarm and Motion icons disappear.)  
Saves the snapshot as an image file in the .jpeg or .bmp format.  
Prints out the current image.  
Reset Alarm  
Capture  
Print  
Record  
Saves the snapshot as a video file in the .avi format.  
Displays the Live screen in full screen.  
Full Screen  
You can set the video format(MJPEG, H.264/MPEG4) for video files.  
The context menu will differ, depending on the codec specified in <Select H.264 &  
MPEG4 Video> of the active viewer.  
Video format  
Alarm output  
On : Activates the specified Alarm Out port.  
Off : Deactivates the specified Alarm Out port.  
Pulse : Activates the Alarm Out port as much time as specified before deactivating it.  
Used to retrieve and customize the Camera Setup menu.  
For selecting and saving each menu item, refer to "How to use the keyboard controller".  
(page 17)  
Camera OSD  
Viewer Screen  
Displays the Live video on the screen.  
40_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BACKUP  
You can capture, print out, and save the snapshot in the specified path.  
To capture the snapshot  
1. Click [ ] on the scene to capture.  
The Capture dialog should appear.  
2. Click [OK].  
The screenshot will be saved in the  
specified path.  
y
y
Default file path  
-
Windows XP : C:\Program Files\  
Samsung\SNC-B2331\SnapShot\Live  
If you want to change the path, click [Set path ( )] and specify a path.  
-
Windows Vista : C:\users\[UserID]\AppData\LocalLow\Samsung\SNC-B2331\  
SnapShot\Live  
On the Windows Vista system, the path to save is fixed.  
The screenshot file will be named automatically in the format of <IP address_Port  
number_YYMMDD_hhmmss_index>.  
ex) 192.168.0.254_10001_20090714_112545_00  
To print out the screenshot  
1. Click [ ] on the scene to print out.  
The Print setup dialog appears.  
2. Specify the name of the printer  
connected, and click [OK].  
English _41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
web viewer  
To record a video  
1. Click [ ] on the scene to record.  
2. You will see the Save AVI dialog;  
provide the necessary information.  
y
y
y
Save path : You can change the  
default saving path.  
File name : You can change the  
default file name.  
HDD minimum free size : If the free  
space on the HDD is less than the  
recorded space, recording will be forcibly ended.  
3. Click [OK].  
Recording will start with the display of  
<REC> on the viewer screen.  
The video file will be saved into the  
specified path.  
4. If you want to quit recording, click [  
]
again.  
y
Default file path  
-
Windows XP : C:\Program Files\Samsung\SNC-B2331\VideoClip\Live  
If you want to change the path, click [Set path ( )] and specify a path.  
-
Windows Vista : C:\users\[UserID]\AppData\LocalLow\Samsung\SNC-B2331\  
VideoClip\Live  
On the Windows Vista system, the path to save is fixed.  
y
y
The screenshot file will be named automatically in the format of <IP address_Port  
number_YYMMDD_hhmmss_index>.  
ex) 192.168.0.254_10001_20090714_112750_00  
If you want to play an .avi file, you must have installed the corresponding DivX  
codec on your system.  
You can get a free download of the DivX from http://sourceforge.net/projects/  
ffdshow/.  
42_ web viewer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
ACCESSING THE SETUP SCREEN  
You can configure the default setting, system, overlay, event and network related settings, and  
change them as necessary.  
1. In the Live screen, click the <Setup> tab.  
2. The Setup screen appears.  
English _43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
DEFAULT SETUP  
To configure the video settings  
You can set the video resolution and quality, and select the codec required.  
1. Select <Basic> - <Video>.  
The Video setup screen appears.  
y
y
y
Brightness : Adjust the screen  
brightness from 1 to 100.  
Contrast : Adjust the contrast from  
1 to 100.  
Resolution : Set the video size of the  
MPEG4, H.264, and MPEG files.  
-
NTSC : 4CIF(704x480),  
VGA(640X480), CIF(352X240)  
-
PAL : 4CIF(704x576),  
VGA(640X480), CIF(352X288)  
y
y
y
Quality : Adjust the picture quality  
from 1 to 10.  
Frame rate : Select one from 30 fps,  
15 fps, 8 fps, 3 fps, and 1 fps.  
Bitrate control* : Select CBR (Constant  
Bit Rate) or VBR (Variable Bit Rate) for  
the compression method.  
If selecting VBR, you can not set the target  
bit rate.  
y
Target bitrate : Transfers video signal  
at a specified bit rate.  
y
y
y
y
y
y
y
Compression : Adjust the compression rate from 5 through 100 by 5.  
Encode priority : Set the video transfer method to Frame rate or Quality.  
GOP* size : Select a GOP size between 5 and 15.  
Deblock : This will soften the edges between macro blocks.  
Profile : Select Baseline or Main for the H.264 profiling method.  
Entropy coding* : Reduces the compression loss due to encoding.  
Motion estimation : Estimates the movement of pixels by determining the motion vector.  
If you set the profile to Baseline, the entropy coding is available only for CAVLC*; if you set it to  
MAIN, the entropy coding is available for both CAVLC* and CABAC*.  
J
2. When done, click [Apply].  
Your settings will be saved.  
44_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To configure the IP settings  
1. Select <Basic> - <IP>.  
The IP setup window appears.  
y
IP configuration : Set the IP and port  
settings for the camera.  
-
IP type : Select one from <Static  
IP>, <Dynamic IP>, and <PPPoE  
IP>.  
If you select <PPPoE IP>, you can  
provide the optional ADSL IP and  
password. However, the multicast items  
(multicast address, port, TTL) for VNP  
and RTP will disappear.  
-
MAC address : Displays the  
Ethernet MAC address.  
This is used for creating a DDNS  
address.  
-
-
IP address : Displays the current IP  
address.  
Subnet mask : Displays the  
<Subnet mask> for the set IP.  
-
-
-
Gateway : Displays the <Gateway> for the set IP.  
DNS server : Displays the DNS(Domain Name Service) server address.  
HTTP webserver port : HTTP port used to access the camera via the web  
browser. The default is 80(TCP).  
-
Upload port (TCP) : Used to upgrade the software firmware, defaulted to 60004(TCP).  
y
y
IPv6 configuration : Obtains the IPv6 address to access the IPv6 network.  
VNP configuration : Set a port used to transfer video signals with the Samsung  
protocols.  
-
-
Device port (TCP) : Used to control the video signal transfer, defaulted to 60001(TCP).  
TCP streaming port : Video signal transfer port using TCP protocols, defaulted  
to 60002(TCP).  
-
-
UDP streaming port : UDP Port used to transfer video signal with the UDP  
Unicast protocols. The default is 60003(UDP).  
Multicast address : IP address used to transfer video signal with the UDP  
Multicast protocols.  
The default is 225.128.1.128, and if you want to change the address, specify it  
ranging from 224.0.0.0 to 239.255.255.255.  
-
-
Multicast port : UDP Port used to transfer video signal with the UDP Multicast  
protocols. The default is 60005(UDP).  
TTL* : Set the TTL for the VNP packet.  
The default is 63, and if you want to change the address, specify it ranging from  
0 to 255.  
English _45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
y
RTP configuration : You can set the RTP protocol.  
-
-
RTSP port : You can set the RTSP port.  
Streaming port : Used to transfer video signal with the RTP protocols.  
The default range is between 61000 and 61999.  
-
Multicast address : IP address used to transfer video signal with the RTP  
protocols.  
-
-
Multicast port : Used to transfer video signal with the RTP-protocol multicasting.  
TTL* : You can set the TTL for the RTP packet.  
2. When done, click [Apply].  
Your settings are saved and the system restarts.  
The currently opened web browser will be closed.  
If the IP router has more than one camera connected, you should configure IP and port settings  
differently with each other.  
M
To set the user account  
1. Click <Basic> - <User>.  
The User setup window appears.  
y
Login authentication : You can set to  
authenticate the login by the user.  
-
If you select <Enable>, the user  
should have gone through the  
login authentication; if selecting  
<Disable>, every user can access  
the system without the login authentication, having the ordinary user permissions.  
-
When done, click [Apply].  
Your settings will be saved.  
2. User login ID/password list : Displays a list of accessible users ID, passwords, and  
ratings.  
-
-
-
You can add up to 10 users.  
The admin ID is "root".  
The password for the admin ID can be changed, but not added or deleted.  
46_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Registration  
1. From the User setup window, click  
[Insert].  
The Register User window appears.  
2. Provide the <User ID>, <Password>,  
and <Confirm password>,  
respectively. You can enter up to 9  
alphanumeric or special characters  
(some excluded) for the user ID and  
password, respectively.  
3. Select a user level.  
Select either <Operator> or <User> for a new user's permission.  
4. Click [Apply].  
The user registration is completed.  
An existing user ID can not be added duplicate.  
Neither root ID nor guest ID can be registered.  
J
To edit a registered user account  
1. From the User setup window, select a  
user ID to change.  
2. From the User setup window, click  
[Modify].  
The Modify user window appears.  
3. Change the <User ID>, <Password>,  
<Confirm password>, and <Level> as  
you wish.  
4. Click [Apply].  
The selected user ID will be changed.  
To delete a user ID  
1. From the User setup window, select a user ID to delete.  
2. From the User setup window, click [Delete].  
The selected user ID will be deleted.  
About the user permission  
M
Administrator : Can use all functions (change/control settings).  
Operator : Can use only the functions available in the Live Viewer.  
User : Can only view the video on the Live Viewer.  
English _47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
To set the display language  
1. Click <Basic> - <Language>.  
The Language setup window appears.  
You can select one from 7 languages  
(English/Korean/Chinese/French/Italian/  
Spanish/German).  
2. When done, click [Apply].  
The selected language will be applied.  
SYSTEM SETUP  
To set the date/time  
You can obtain the current system time from the NTP server or your PC for your time  
setting.  
1. Select <System> - <Date & Time>.  
The Date & Time setup window appears.  
2. If you select Manual, input the date and  
time manually.  
Your settings will be saved.  
y
Current system time : The specified  
time in System Time Setup will be  
applied.  
y
System time setup : You can  
synchronize the system time with the NTP server (time server) or your PC, or  
specify it manually.  
You can specify the time between January 1, 2000 and December 31, 2037.  
M
To set the system time  
1. Select a desired address in <Address>  
or select <Synchronize with PC  
viewer>.  
2. If you select Manual, input the date and  
time manually.  
3. Click [Apply].  
The specified system time will be applied.  
48_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
<NTP Server IP> is provided by a public agency, the list of which is subject to change from time  
to time.  
M
J
In a local network, a separate NTP server must be manually defined.  
The current time can vary depending on the computers regional (GMT and DST) and country (PC  
time configuration) settings.  
To check the log information  
Select <System> - <Log>.  
The Log information list appears.  
y
System log list : Shows the log  
information about the system changes  
along with time and IP address.  
-
User login : Shows the current login  
user to the camera.  
-
Video configuration change : Show  
video setting changes.  
-
-
System time change : Shows the time changes.  
System started : Shows time when the camera is turned on.  
The maximum of 2000 logs can be recorded.  
If the log number is over 2000, the log in the bottom of the log list will be replaced with a new log.  
M
To update the software  
Select <System> - <Software update>.  
The Software update window appears.  
How to update the software  
1. From the software update window, click  
[Browse…].  
The Open dialog appears.  
2. Select an updatable file and click  
[Open].  
3. From the software update window, click  
[Install].  
The selected file will be unzipped with a  
start of the update.  
It may take a several minutes to  
complete the update.  
English _49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
4. When the software update is completed, you will be prompted to restart the system.  
5. Click [OK] to restart the system.  
Since the current connection is disconnected, you have to connect to the system again.  
If the network is disconnected, the power supply fails, or the PC abnormally operates during the  
update, the system does not work at all.  
J
To reset the system  
Restart or reset the system if it does not work properly or causes a problem.  
Select <System> - <Reset>.  
The Reset window appears.  
y
y
Restart : Restarts the system.  
Factory default : Resets the system  
settings to the factory defaults with  
following two options:  
-
-
Except network parameter : Resets all settings except for the Network Parameters.  
All : Restores all settings to the default.  
This works the same as pressing the [RESET] button on the rear of the camera.  
After the system is reset or restarts, you should try to connect to the camera again.  
J
It takes several minutes until the system completes rebooting. Wait until the system rebooting is  
completed and try to connect again.  
After executing <Factory default>, you must run the <IP Installer.exe> program to change the  
basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to  
the Internet.  
To set the HTTPS  
1. Select <System> - <HTTPS>.  
The HTTPS setup window appears.  
y
Secure connection system : Select  
a secure connection system to use.  
To use the secure connection mode  
requiring the public certificate for the  
secure connection system, you must  
have installed a signed certificate  
issued by a certificate authority on  
your system.  
50_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
y
Install a public certificate : To install the certificate to camera, you need to type a  
certificate name (it can be arbitrarily assigned by user), certificate file issued from  
the authority and a key file. When done, click [Install].  
If the certificate is installed successfully, the user-defined certificate name will be  
displayed. Also, the option button of <HTTPS (Secure connection mode using  
the public certificate)> in the upper side becomes activated.  
To access the camera using HTTPS mode, you have to type the IP address for the camera in the  
form of “https://<Camera_IP>”.  
M
2. When done, click [Apply].  
The web viewer will switch to the set secure connection system.  
OVERLAY SETUP  
You can display text on the screen.  
To set the text  
1. Select <Overlay> - <Overlay text>.  
The Overlay Text setup window  
appears.  
2. When done, click [Apply].  
Your settings will be saved.  
y
Overlay text settings : If you select  
<Disable>, the overlay text will not  
be displayed; If selecting <Enable>, it will display on the screen.  
y
Show date : Set to display the date information on the bottom screen.  
-
Output Format : Select a display format of the date information.  
YYYY-MM-DD : Year-Month- Day / MM-DD-YYYY : Month-Day-Year/  
DD-MM-YYYY : Day-Month-Year  
y
Show time : Set to display the time information on the bottom screen.  
-
Output Format : Select a display format of the time information.  
24hr : Displays the time in the 24-hour format.  
12hr : Displays the time in the 12-hour format.  
y
y
Text color : Select black or white for the text color.  
Background color : Select black or white for the background color.  
English _51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
EVENT SETUP  
To set the event transfer function  
You can set the FTP/email server (SMTP) to transfer the alarm images present in the  
camera, in case an alarm event occurs.  
Select <Event> - <Transfer setup>.  
The Image transfer setup window appears.  
For more information on commercial  
SMTP services, contact the SMTP service  
provider.  
M
To test the FTP transfer  
Click [Test].  
This will test if the image is transferred to the  
specified FTP server properly.  
When the test on the FTP server connection  
and transfer is done, a message of  
<( Verified )> will be displayed.  
You will see an error message if the test  
fails. If this is the case, check the FTP server  
status or the settings again.  
y
FTP transfer : With this, you can transfer alarm images to the FTP server. If the initial FTP  
server setting and the connection status are not verified, the <( Not verified )> message  
appears.  
-
Use passive mode : Select this option when the passive mode connection is  
inevitable due to the firewall or FTP server setting.  
-
FTP server address : Enter the IP address of a FTP server to which an alarm image  
will be transferred.  
52_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-
-
Upload path : You can specify the path of the FTP directory to which you will  
transfer an alarm image.  
You can specify the path by just typing </directory name> or <directory name> in  
this field.  
If nothing is specified, the path will be defaulted to the root directory of the FTP  
server.  
Port : The FTP port is defaulted to 21. This value can be changed according to the  
FTP server setting.  
-
-
User ID : Provide the user account ID to access the FTP server.  
Password : Provide the user account password to access the FTP server.  
y
E-mail(SMTP) transfer : With this setting, you can transfer alarm images to the email  
server. This function is available only for the SMTP email server. When the initial SMTP  
server setting and connection are not verified, the <Not verified> message appears.  
-
SMTP server address : Enter the SMTP server address to use when you send an  
email.  
ex) 10.240.56.228  
-
-
-
-
Port : Enter a port number to use when you send an email. The default is 25.  
User ID : Provide the user account ID to access the SMTP server.  
Password : Provide the user account password to access the SMTP server.  
E-mail sender : Enter the address of the email sender. If the sender address is  
incorrect, the email from the sender may be classified as SPAM by the SMTP  
server and may not be sent.  
-
-
-
E-mail receiver : Enter the address of the email receiver.  
Title : Enter the subject of the email to send.  
Message : Enter the content of the email to send.  
To test the email transfer  
Click [Test].  
This will test if the image is transferred to the  
specified SMTP server properly. When the  
test on the SMTP server connection and  
transfer is done, a message of <( Verified )>  
will be displayed.  
You will see an error message if the test  
fails.  
If this is the case, check the SMTP server  
status or the settings again.  
English _53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
To set an alarm image  
You can set to transfer the alarm image to the FTP/SMTP server.  
Select a transfer method when an event occurs or the schedule transfer function is  
activated.  
1. Select <Event> - <Alarm image>.  
The Alarm Image setup window  
appears.  
y
Transfer mode : Select an alarm  
image transfer mode from FTP  
transfer and E-mail transfer.  
-
FTP transfer : The image is sent to  
the specified FTP address.  
-
E-mail transfer : The image is sent  
to the specified email address.  
y
y
Transferred image naming setup : You can set the file name of an alarm image  
to be sent when an alarm is triggered or during the scheduled transfer.  
Pre/post alarm image : You can set to save the pre or post alarm image.  
-
-
Number of image : The frame rate per second can be one among 1, 2, 3, and 5.  
Pre-alarm duration : The pre alarm duration can be one among 5 seconds, 10  
seconds, 15 seconds, and 30 seconds. You can send a pre-alarm image of up  
to 30 seconds before the alarm is triggered.  
(The max time differs, depending on the frame rate)  
-
Post-alarm duration : The post alarm duration can be one among 5 seconds, 10  
seconds, 15 seconds, and 30 seconds. You can send a post-alarm image of up  
to 30 seconds after the alarm is triggered.  
(The max time differs, depending on the frame rate)  
The pre/post alarm duration is not available in SMTP transfer mode.  
Only one image at the corresponding time will be transferred.  
M
2. When done, click [Apply].  
Your settings will be saved.  
54_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To set the alarm input  
1. Select <Event> - <Alarm input 1> or  
<Alarm input 2>.  
The Alarm Input setup window appears.  
2. When done, click [Apply].  
Your settings will be saved.  
y
Input device setup : Select an input  
type according to the characteristics  
of the alarm sensor on the rear of the  
camera.  
-
-
Off : Turns off the alarm input setting.  
NO (Normal Open) : It is normally open, but if it is closed, an alarm will be  
triggered.  
-
NC (Normal Close) : It is normally closed, but if it is open, an alarm will be  
triggered.  
y
y
Activation time : You can set a time to execute a specific command when an  
alarm occurs.  
-
-
Always : Always executes the specified command when an alarm occurs.  
Only scheduled time : Executes the specified command when an alarm occurs  
only on a specified weekday, or time.  
Action : You can set an action to execute when an alarm occurs.  
-
-
Alarm output : Set the alarm output port to which the alarm signal is transferred.  
Output duration : Set the period of time to output the alarm signal to the  
specified alarm output port when an alarm occurs.  
If a new alarm event is detected during the alarm output, the delay time is  
recalculated based on the detection time of the recent alarm.  
-
Alarm image transfer : If you select <On>, you can transfer JPEG images to the FTP  
or SMTP server according to the setting in <Event> - <Transfer setup>.  
To set the motion detection function  
1. Select <Event> - <Motion>.  
The Motion Detection setup window  
appears.  
2. When done, click [Apply].  
Your settings will be saved.  
y
M.D. function : If selecting <Enable>,  
the motion detection function will be  
activated; if selecting <Disable>, it will  
not operate at all.  
English _55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
y
M.D. configuration : Configure the motion detection settings.  
-
Motion sensitivity : Select one from <High>, <Medium> and <Low>.  
Selecting <High> will trigger the motion detection event even with a small motion.  
-
Motion area : Set an area where the motion detection is performed.  
y
Activation time : Set the time to activate a specified operation when a motion is  
detected.  
-
-
Always : Always executes the specified command when a motion is detected.  
Only scheduled time : Executes the specified command when a motion is  
detected only on a specified weekday, or time.  
y
Action : You can set an action to execute when a motion is detected.  
-
Alarm output : Set the alarm output port to which the motion detection signal is  
transferred.  
-
Output duration : Set the period of time to output the motion detection signal to the  
specified alarm output port when a motion is detected.  
If another motion is detected during the alarm output, the delay time is recalculated  
based on the detection time of the recent motion.  
-
Alarm image transfer : If you select <On>, you can transfer JPEG images to the  
FTP or SMTP server according to the setting in <Event> - <Transfer setup>.  
To set a motion area  
You can set a specific area to detect a motion in.  
1. From the Motion Detection setup  
window, click [Setup] in the <Motion  
area>.  
The Motion Area window appears.  
You can set a specific area to detect a  
motion in.  
2. Click over square boxes corresponding  
to the target motion area.  
The selected area will be highlighted  
yellow.  
3. To cancel the selection, click the  
square box again.  
The square box will restore its original color.  
4. When done, click [Apply].  
Your settings will be saved.  
The Motion Detection function will operate on the selected area.  
56_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To set the scheduled transfer  
You can set to transfer the JPEG image to the FTP/SMTP server at a specific interval.  
1. Select <Event> - <Schedule>.  
The Schedule Transfer setup window  
appears.  
y
Schedule transfer function :  
If selecting <Enable>, the schedule  
transfer function will be activated;  
if selecting <Disable>, it will be  
deactivated.  
y
y
Transfer interval : You can set the  
time interval to transfer images.  
You can set the unit of the interval to <seconds> or <minutes>; you can also set to  
transfer one image per 5/15/30/45/60 seconds, or one per 5/15/30/45/60 minutes.  
Activation time : You can set a time to execute a specific command when a sched-  
ule transfer event occurs.  
-
-
Always : Always sends an image at the set interval.  
Only scheduled time : Sends the image only on a specified weekday, or time.  
2. If you select Manual, input the date and time manually.  
Your settings will be saved.  
NETWORK SETUP  
To set the video transfer mode  
You can control the transfer rate according to the video transfer mode and network speed.  
1. Select <Network> - <Streaming type>.  
The Video Transfer setup window appears.  
2. When done, click [Apply].  
Your settings will be saved.  
y
VNP streaming : You can set the  
Samsung Protocol (VNP) for the  
streaming service.  
-
Protocol : Select a video transfer protocol from TCP*, UDP (Unicast)*, and UDP  
(Multicast)*.  
Multicast backbone (MBone) is not supported; you can access the camera only in the  
multicast local network environment.  
y
RTP streaming : You can set the RTP Protocol or the streaming service.  
Protocol : Select a video transfer protocol from UDP (Unicast) and UDP (Multicast).  
-
English _57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup screen  
To set the DDNS  
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address  
of a camera into a general Host Name so that the user can easily remember it and enables  
connecting a camera with a fixed Host Name even if the IP address of the camera may be  
dynamically changed.  
1. Select <Network> - <DDNS>.  
The DDNS setup window appears.  
2. When done, click [Apply].  
Your settings will be saved.  
For checking the DDNS address, refer to "To check the DDNS address". (page 38)  
M
58_ setup screen  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
PROFILE  
CAMERA SETUP MENU  
STANDARD  
ITS  
BACKLIGHT  
DAY/NIGHT  
GAMING  
Parent Menu  
Sub-menus  
ALC  
-
ALC  
-
ALC  
-
ALC  
-
ALC  
-
ALC  
IRIS  
LENS  
DC  
0
DC  
0
DC  
0
DC  
0
DC  
0
LEVEL  
BACKLIGHT  
OFF  
OFF  
BLC  
OFF  
OFF  
(F.FAST)  
---  
(F.FAST)  
---  
(F.FAST)  
---  
MOTION  
NORM  
SLOW  
DNR  
SHUTTER  
SENSE UP  
XDR  
MID  
MID  
MID  
MID  
MID  
OFF  
AUTO 1/250  
OFF  
OFF  
OFF  
AUTO X4  
AUTO X2  
AUTO X4  
AUTO X4  
AUTO X4  
MID  
MID  
MID  
MID  
MID  
AUTO  
AUTO  
DAY  
AUTO  
DAY  
DAY/NIGHT NIGHT  
DAY  
-
-
-
-
-
BURST  
OFF  
ON  
OFF  
OFF  
OFF  
DAY  
DAY/NIGHT  
DAY  
DAY/NIGHT  
DAY  
-
-
-
-
-
MODE  
RED  
ATW2  
ATW1  
ATW1  
ATW1  
ATW1  
0
0
0
0
0
BLUE  
0
0
0
0
0
WHITE BAL  
NIGHT  
-
-
MID  
ATW2  
0
-
-
MID  
ATW2  
0
-
BRIGHTNESS  
MODE  
Custom Setting  
OFF  
Custom Setting  
OFF  
Custom Setting  
OFF  
RED  
Custom Setting  
Custom Setting  
2
Custom Setting  
Custom Setting  
2
Custom Setting  
Custom Setting  
2
BLUE  
0
0
DETAIL  
2
2
English _59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
TERMINOLOGY  
y
GOP : The default is 15, and if set to 15, one I-Frame will be output per 15 frames as one  
I-Frame and 14 P-Frames constitute the GOP.  
The lower the GOP size is, the better the quality is; however, the bit rate as well as the data  
size will increase, causing a lower of the fps. GOP(Group of Pictures) is a set of video frames  
for MPEG4 and H.264 format compression, indicating a collection of frames from the initial  
I-Frame (key frame) to the next I-Frame. GOP consists of 2 kinds of frames: I-Frame and  
P-Frame. I-Frame is the basic frame for the compression, also known as Key Frame, which  
contains one complete image data. P-Frame contains only the data that has changed from  
the preceding I-Frame.  
y
y
Entropy coding : Data transfer technology used to reduce the compression loss from encoding.  
-
CAVLC (Context-adaptive variable-length coding): Records a higher compression loss  
rate than CABAC.  
-
CABAC (Context-adaptive binary arithmetic coding): Shows a lesser compression loss than  
CAVLC.  
Bitrate Control  
-
CBR(Constant Bitrate)  
This will transfer video data in an equal size at all times, regardless of the video  
complexity. The video quality may be deteriorated, depending on the video complexity.  
-
VBR(Variable Bitrate)  
The amount of video data to transfer may differ, depending on the video complexity. This  
enables receiving video data in an equal quality at all times.  
y
y
TTL : TTL stands for “Time To Live”, which you can specify to prevent loss of data packet that  
passes through multiple-staged routers. Each router decreases the TTL value by one each  
time a packet passes it through; If the TTL value reaches 0, the packet cannot further pass  
through a router.  
TCP : It is a general purpose protocol used for transmission that requires reliability. With  
constant communication between the sender and recipient, it provides high reliability against  
transmission data loss; however, it has imitation to transmit a large amount of data in real time  
at a high speed.  
It enables reliable data transmission over xDSL and cable network at a relatively slow speed.  
y
y
UDP (Unicast): It refers to a system that transmits data between only one transmitter and one  
receiver (1:1).  
UDP (Multicast): It refers to the data transfer protocol in one-to-many (1:N) between the trans-  
mitting and receiving terminals; although it alleviates the network load, it requires <Multicast>  
router.  
For more information such as whether the network over which the camera is installed sup-  
ports <Multicast>, contact the network administrator.  
y
UDP : It is a protocol appropriate to transmit a large amount of data such as multimedia data at a  
high speed. However, with its nonconnection structure, it records a higher transmission efficiency  
than TCP especially in a high LAN environment faster than 100Mbps.  
60_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Description  
Item  
NTSC  
PAL  
Camera  
Color/BW  
Type  
Color  
Device  
1/3" Super-HAD PS CCD  
811 x 508  
Image  
Pixels  
Total  
795 x 596  
752 x 582  
Effective  
768 x 494  
System  
Progressive  
Scanning  
Horizontal Frequency  
Vertical Frequency  
15.734 Hz  
15.625 Hz  
50 Hz  
59.94 Hz  
Sens off : 0.12 Lux(15 IRE), 0.24 Lux(30 IRE),  
0.4Lux(50 IRE)@F1.2  
Sens up x512 : 0.00023 Lux(15 IRE), 0.00047 Lux(30 IRE),  
0.0008Lux(50 IRE)@F1.2  
Color  
B/W  
Min. Scene  
Illumination  
Sens off : 0.012 Lux(15 IRE), 0.024 Lux(30 IRE),  
0.04Lux(50 IRE)@F1.2  
Sens up x512 : 0.000023 Lux(15 IRE), 0.000047 Lux(30  
IRE), 0.00008Lux(50 IRE)@F1.2  
Number of Privacy Zone  
Day/Night  
12 ea  
Day/Night/AUTO(Soft Method)  
Off/On (Level Setting)  
x1 ~ x16 (x0.1 STEP)  
Off/On (Advanced)  
Extended Dynamic Range  
D-Zoom  
PIP  
High Speed Shutter  
Flickerless  
1/60 ~ 1/10Ksec  
Off/On  
1/50 ~ 1/10Ksec  
Sens Up  
x2 ~ x512  
Functions  
BLC  
Off/On (Area Setting)  
Off/On (Max.Level Setting)  
Off/On ( ~ 1/200Ksec)  
Off/On (Max.54ea/2Line)  
AGC  
ELC  
Camera ID  
White Balance  
Digital Noise Reduction  
Digital Image Stablization  
Etc. Function  
ATW1/ATW2/AWC/3200K/5600K  
Off/On (Adaptive 3D+2D)  
Off/On  
Detail, Reverse(H/V), Posi/Nega  
Horizontal  
Vertical  
600 TV Lines  
350 TV Lines  
Resolution  
English _61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Description  
Item  
NTSC  
VBS 1.0Vp-p  
PAL  
Video Output Video Output  
S/N Ratio  
S/N Ratio  
Lens Drive Type  
Mount Type  
OS  
about 52 dB  
MANUAL/AI(VIDEO/DC)  
CS/C  
Lens  
Embedded Linux  
32M byte  
Flash memory  
RAM  
256M byte  
Network  
Board  
Hardware  
DSP  
TI Davinci  
Ethernet  
PoE  
RJ-45 (10/100BASE-T)  
Yes (IEEE802.3af)  
2 ea  
Input  
Alarm  
Video  
OSD  
Output  
2 ea  
H.264 / MPEG4 / MJPEG Multiple Codec  
(H.264 / MPEG4 selectable)  
Simultaneous Dual Streaming  
Compression  
Resolution  
4CIF  
VGA  
CIF  
704x480  
704x576  
640x480  
352x240  
352x288  
Frame Rate  
Quality  
30, 15, 8, 3, 1 fps  
25, 13, 6, 3, 1 fps  
1 ~ 10 level  
OSD menu on Video  
Camera Control and Adjustment (Menu enter/exit, move by Web UI)  
* Some key adjustment menus will be supported by CGI API.  
Motion  
Detection  
Sensitivity and Area Setting  
High, Medium, Low  
62_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description  
Item  
NTSC  
PAL  
IP  
IPv4 / IPv6  
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTSP, NTP, HTTP,  
HTTPS, SSL, DHCP  
PPPoE, FTP, SMTP, ICMP, IGMP, SNMPv1/v2c/v3(MIB-2),  
ARP, DNS, DDNS, VSIP  
IPv4  
IPv6  
Network  
Protocol  
Protocol  
TCP/IP, HTTP, HTTPS, SSL, DHCP  
Unicast (TCP, UDP), Multicast (UDP)  
Streaming  
Security  
DDNS  
HTTPS Login Authentication  
Digest Login Authentication  
Supporting Samsung DDNS and Public DDNS services  
Max 10 Users at Unicast (TCP, UDP) Mode  
Max 20 Users at Multicast (UDP) Mode  
Maximum User Access  
Live Monitoring, Alarm I/O control, OSD menu control,  
SETUP  
Administrator  
Connection  
User Access  
Level  
Operator  
User  
Live Monitoring, Alarm I/O control  
Live Monitoring  
JPEG Image transfer : FTP, SMTP  
Notification : notify to viewer or by E-mail (one image  
attachment)  
Alarm Input  
Event  
Management  
Motion Detection  
Alarm Out  
Schedule  
JPEG Image transfer : FTP, SMTP  
Windows XP, VISTA  
Internet Explorer 6.0 or Higher  
E/F/G/S/I/C/K  
Supported OS  
Supported Browser  
UI Language  
S/W upgrade  
Web Browser  
Viewer  
(Default)  
Support  
Video Player RTP/RTSP streaming  
Quicktime, VLC player  
Video  
Management  
Software  
Samsung NET-i  
3rd Party S/W appliction  
Application  
IP Installation  
HTTP API  
IP Installer Application for All Samsung IP Devices  
Provides functionality to control cameras  
and set/retrieve internal parameter values.  
Get JPEG image or MJPEG stream  
Alarm In/Out control  
CGI Command  
SDK  
SDK  
RTP/RTSP API  
ActiveX  
RTP Header, RTSP Command Document  
ActiveX API for viewing data streams from IP camera.  
English _63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
Description  
Item  
NTSC  
PAL  
AC24V 10%(60Hz 0.3Hz)/ DC12V+10%/-5% /  
PoE (Power over Ethernet)  
Power  
Power Consumption  
Operating Temp.  
Operating Humidity  
Dimension  
About 7W  
-10˚C~50˚C  
~90%  
W72 X D139 X H60  
About 300g  
Weight  
64_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME RATE (NTSC)  
Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)  
M
H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),  
GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion  
estimation(HPel)  
MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),  
GOP size(15)  
MPEG4 (4CIF)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
4239 Kbps  
23 FPS  
2765 Kbps  
15 FPS  
1290 Kbps  
7 FPS  
737 Kbps  
4 FPS  
221 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
3686 Kbps  
24 FPS  
2304 Kbps  
15 FPS  
1075 Kbps  
7 FPS  
614 Kbps  
4 FPS  
184 Kbps  
1 FPS  
3072 Kbps  
25 FPS  
1843 Kbps  
15 FPS  
860 Kbps  
7 FPS  
492 Kbps  
4 FPS  
147 Kbps  
1 FPS  
2396 Kbps  
26 FPS  
1382 Kbps  
15 FPS  
645 Kbps  
7 FPS  
369 Kbps  
4 FPS  
111 Kbps  
1 FPS  
1659 Kbps  
27 FPS  
922 Kbps  
15 FPS  
430 Kbps  
7 FPS  
246 Kbps  
4 FPS  
74 Kbps  
1 FPS  
1336 Kbps  
29 FPS  
691 Kbps  
15 FPS  
323 Kbps  
7 FPS  
184 Kbps  
4 FPS  
55 Kbps  
1 FPS  
1133 Kbps  
30 FPS  
576 Kbps  
15 FPS  
269 Kbps  
7 FPS  
154 Kbps  
4 FPS  
46 Kbps  
1 FPS  
922 Kbps  
30 FPS  
461 Kbps  
15 FPS  
215 Kbps  
7 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
691 Kbps  
30 FPS  
346 Kbps  
15 FPS  
161 Kbps  
7 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
461 Kbps  
30 FPS  
230 Kbps  
15 FPS  
108 Kbps  
7 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
English _65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (4CIF)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
2298 Kbps  
19 FPS  
1229 Kbps  
10 FPS  
737 Kbps  
6 FPS  
369 Kbps  
3 FPS  
147 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1751 Kbps  
19 FPS  
1198 Kbps  
13 FPS  
645 Kbps  
7 FPS  
369 Kbps  
4 FPS  
111 Kbps  
1 FPS  
1536 Kbps  
20 FPS  
1075 Kbps  
14 FPS  
538 Kbps  
7 FPS  
307 Kbps  
4 FPS  
92 Kbps  
1 FPS  
1352 Kbps  
22 FPS  
897 Kbps  
15 FPS  
430 Kbps  
7 FPS  
246 Kbps  
4 FPS  
74 Kbps  
1 FPS  
1129 Kbps  
25 FPS  
691 Kbps  
15 FPS  
369 Kbps  
8 FPS  
184 Kbps  
4 FPS  
55 Kbps  
1 FPS  
960 Kbps  
25 FPS  
576 Kbps  
15 FPS  
307 Kbps  
8 FPS  
154 Kbps  
4 FPS  
46 Kbps  
1 FPS  
799 Kbps  
26 FPS  
461 Kbps  
15 FPS  
246 Kbps  
8 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
622 Kbps  
27 FPS  
346 Kbps  
15 FPS  
184 Kbps  
8 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
445 Kbps  
29 FPS  
230 Kbps  
15 FPS  
123 Kbps  
8 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
223 Kbps  
29 FPS  
115 Kbps  
15 FPS  
61 Kbps  
8 FPS  
31 Kbps  
4 FPS  
9 Kbps  
1 FPS  
66_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPEG4 (VGA)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
4055 Kbps  
22 FPS  
2580 Kbps  
14 FPS  
1290 Kbps  
7 FPS  
737 Kbps  
4 FPS  
221 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
3533 Kbps  
23 FPS  
2304 Kbps  
15 FPS  
1075 Kbps  
7 FPS  
614 Kbps  
4 FPS  
184 Kbps  
1 FPS  
2949 Kbps  
24 FPS  
1843 Kbps  
15 FPS  
860 Kbps  
7 FPS  
492 Kbps  
4 FPS  
147 Kbps  
1 FPS  
2304 Kbps  
25 FPS  
1382 Kbps  
15 FPS  
645 Kbps  
7 FPS  
369 Kbps  
4 FPS  
111 Kbps  
1 FPS  
1536 Kbps  
25 FPS  
922 Kbps  
15 FPS  
430 Kbps  
7 FPS  
246 Kbps  
4 FPS  
74 Kbps  
1 FPS  
1152 Kbps  
25 FPS  
691 Kbps  
15 FPS  
323 Kbps  
7 FPS  
184 Kbps  
4 FPS  
55 Kbps  
1 FPS  
998 Kbps  
26 FPS  
576 Kbps  
15 FPS  
269 Kbps  
7 FPS  
154 Kbps  
4 FPS  
46 Kbps  
1 FPS  
799 Kbps  
26 FPS  
461 Kbps  
15 FPS  
246 Kbps  
8 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
622 Kbps  
27 FPS  
346 Kbps  
15 FPS  
184 Kbps  
8 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
415 Kbps  
27 FPS  
230 Kbps  
15 FPS  
123 Kbps  
8 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
English _67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (VGA)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
2089 Kbps  
17 FPS  
1229 Kbps  
10 FPS  
737 Kbps  
6 FPS  
369 Kbps  
3 FPS  
147 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1659 Kbps  
18 FPS  
1014 Kbps  
11 FPS  
553 Kbps  
6 FPS  
276 Kbps  
3 FPS  
111 Kbps  
1 FPS  
1459 Kbps  
19 FPS  
845 Kbps  
11 FPS  
538 Kbps  
7 FPS  
307 Kbps  
4 FPS  
92 Kbps  
1 FPS  
1229 Kbps  
20 FPS  
737 Kbps  
12 FPS  
430 Kbps  
7 FPS  
246 Kbps  
4 FPS  
74 Kbps  
1 FPS  
1014 Kbps  
22 FPS  
691 Kbps  
15 FPS  
323 Kbps  
7 FPS  
184 Kbps  
4 FPS  
55 Kbps  
1 FPS  
883 Kbps  
23 FPS  
576 Kbps  
15 FPS  
269 Kbps  
7 FPS  
154 Kbps  
4 FPS  
46 Kbps  
1 FPS  
707 Kbps  
23 FPS  
461 Kbps  
15 FPS  
215 Kbps  
7 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
553 Kbps  
24 FPS  
346 Kbps  
15 FPS  
161 Kbps  
7 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
384 Kbps  
25 FPS  
230 Kbps  
15 FPS  
108 Kbps  
7 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
200 Kbps  
26 FPS  
115 Kbps  
15 FPS  
54 Kbps  
7 FPS  
31 Kbps  
4 FPS  
9 Kbps  
1 FPS  
68_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPEG4 (CIF)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
1382 Kbps  
30 FPS  
691 Kbps  
15 FPS  
369 Kbps  
8 FPS  
184 Kbps  
4 FPS  
55 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1152 Kbps  
30 FPS  
576 Kbps  
15 FPS  
307 Kbps  
8 FPS  
154 Kbps  
4 FPS  
46 Kbps  
1 FPS  
922 Kbps  
30 FPS  
461 Kbps  
15 FPS  
246 Kbps  
8 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
691 Kbps  
30 FPS  
346 Kbps  
15 FPS  
184 Kbps  
8 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
461 Kbps  
30 FPS  
230 Kbps  
15 FPS  
123 Kbps  
8 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
346 Kbps  
30 FPS  
173 Kbps  
15 FPS  
92 Kbps  
8 FPS  
46 Kbps  
4 FPS  
14 Kbps  
1 FPS  
288 Kbps  
30 FPS  
144 Kbps  
15 FPS  
77 Kbps  
8 FPS  
38 Kbps  
4 FPS  
12 Kbps  
1 FPS  
230 Kbps  
30 FPS  
115 Kbps  
15 FPS  
61 Kbps  
8 FPS  
31 Kbps  
4 FPS  
9 Kbps  
1 FPS  
173 Kbps  
30 FPS  
86 Kbps  
15 FPS  
46 Kbps  
8 FPS  
23 Kbps  
4 FPS  
7 Kbps  
1 FPS  
151 Kbps  
30 FPS  
76 Kbps  
15 FPS  
40 Kbps  
8 FPS  
20 Kbps  
4 FPS  
6 Kbps  
1 FPS  
English _69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (CIF)  
Frame Rate  
30 FPS  
15 FPS  
8 FPS  
3 FPS  
1 FPS  
Quality  
922 Kbps  
30 FPS  
461 Kbps  
15 FPS  
215 Kbps  
7 FPS  
123 Kbps  
4 FPS  
37 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
691 Kbps  
30 FPS  
346 Kbps  
15 FPS  
184 Kbps  
8 FPS  
92 Kbps  
4 FPS  
28 Kbps  
1 FPS  
576 Kbps  
30 FPS  
288 Kbps  
15 FPS  
134 Kbps  
7 FPS  
77 Kbps  
4 FPS  
23 Kbps  
1 FPS  
461 Kbps  
30 FPS  
230 Kbps  
15 FPS  
108 Kbps  
7 FPS  
61 Kbps  
4 FPS  
18 Kbps  
1 FPS  
346 Kbps  
30 FPS  
173 Kbps  
15 FPS  
81 Kbps  
7 FPS  
46 Kbps  
4 FPS  
14 Kbps  
1 FPS  
288 Kbps  
30 FPS  
144 Kbps  
15 FPS  
67 Kbps  
7 FPS  
38 Kbps  
4 FPS  
12 Kbps  
1 FPS  
230 Kbps  
30 FPS  
115 Kbps  
15 FPS  
54 Kbps  
7 FPS  
31 Kbps  
4 FPS  
9 Kbps  
1 FPS  
173 Kbps  
30 FPS  
86 Kbps  
15 FPS  
40 Kbps  
7 FPS  
23 Kbps  
4 FPS  
7 Kbps  
1 FPS  
115 Kbps  
30 FPS  
58 Kbps  
15 FPS  
27 Kbps  
7 FPS  
15 Kbps  
4 FPS  
5 Kbps  
1 FPS  
58 Kbps  
30 FPS  
29 Kbps  
15 FPS  
13 Kbps  
7 FPS  
8 Kbps  
4 FPS  
2 Kbps  
1 FPS  
70_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FRAME RATE (PAL)  
Test Condition: MJPEG - Resolution(CIF), Quality(1), Frame rate(1)  
M
H.264 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),  
GOP size(15), Deblock(ON), Profile(Baseline), Entropy coding(CAVLC), Motion  
estimation(HPel)  
MPEG4 - Bitrate control(CBR), Compression(40), Encode Priority(Frame rate),  
GOP size(15)  
MPEG4 (4CIF)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
4645 Kbps  
21 FPS  
2654 Kbps  
12 FPS  
1327 Kbps  
6 FPS  
664 Kbps  
3 FPS  
221 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
4055 Kbps  
22 FPS  
2212 Kbps  
12 FPS  
1106 Kbps  
6 FPS  
553 Kbps  
3 FPS  
184 Kbps  
1 FPS  
3391 Kbps  
23 FPS  
1769 Kbps  
12 FPS  
885 Kbps  
6 FPS  
442 Kbps  
3 FPS  
147 Kbps  
1 FPS  
2544 Kbps  
23 FPS  
1327 Kbps  
12 FPS  
664 Kbps  
6 FPS  
332 Kbps  
3 FPS  
111 Kbps  
1 FPS  
1769 Kbps  
24 FPS  
885 Kbps  
12 FPS  
442 Kbps  
6 FPS  
221 Kbps  
3 FPS  
74 Kbps  
1 FPS  
1382 Kbps  
25 FPS  
664 Kbps  
12 FPS  
332 Kbps  
6 FPS  
166 Kbps  
3 FPS  
55 Kbps  
1 FPS  
1152 Kbps  
25 FPS  
553 Kbps  
12 FPS  
276 Kbps  
6 FPS  
138 Kbps  
3 FPS  
46 Kbps  
1 FPS  
922 Kbps  
25 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
691 Kbps  
25 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
461 Kbps  
25 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
English _71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (4CIF)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
2359 Kbps  
16 FPS  
1180 Kbps  
8 FPS  
737 Kbps  
5 FPS  
442 Kbps  
3 FPS  
147 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1991 Kbps  
18 FPS  
1106 Kbps  
10 FPS  
664 Kbps  
6 FPS  
332 Kbps  
3 FPS  
111 Kbps  
1 FPS  
1751 Kbps  
19 FPS  
1014 Kbps  
11 FPS  
553 Kbps  
6 FPS  
276 Kbps  
3 FPS  
92 Kbps  
1 FPS  
1475 Kbps  
20 FPS  
885 Kbps  
12 FPS  
442 Kbps  
6 FPS  
221 Kbps  
3 FPS  
74 Kbps  
1 FPS  
1161 Kbps  
21 FPS  
664 Kbps  
12 FPS  
332 Kbps  
6 FPS  
166 Kbps  
3 FPS  
55 Kbps  
1 FPS  
968 Kbps  
21 FPS  
553 Kbps  
12 FPS  
276 Kbps  
6 FPS  
138 Kbps  
3 FPS  
46 Kbps  
1 FPS  
811 Kbps  
22 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
608 Kbps  
22 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
424 Kbps  
23 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
230 Kbps  
25 FPS  
111 Kbps  
12 FPS  
55 Kbps  
6 FPS  
28 Kbps  
3 FPS  
9 Kbps  
1 FPS  
72_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPEG4 (VGA)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
4424 Kbps  
20 FPS  
2654 Kbps  
12 FPS  
1327 Kbps  
6 FPS  
664 Kbps  
3 FPS  
221 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
3871 Kbps  
21 FPS  
2212 Kbps  
12 FPS  
1106 Kbps  
6 FPS  
553 Kbps  
3 FPS  
184 Kbps  
1 FPS  
3097 Kbps  
21 FPS  
1769 Kbps  
12 FPS  
885 Kbps  
6 FPS  
442 Kbps  
3 FPS  
147 Kbps  
1 FPS  
2433 Kbps  
22 FPS  
1327 Kbps  
12 FPS  
664 Kbps  
6 FPS  
332 Kbps  
3 FPS  
111 Kbps  
1 FPS  
1769 Kbps  
24 FPS  
885 Kbps  
12 FPS  
442 Kbps  
6 FPS  
221 Kbps  
3 FPS  
74 Kbps  
1 FPS  
1382 Kbps  
25 FPS  
664 Kbps  
12 FPS  
332 Kbps  
6 FPS  
166 Kbps  
3 FPS  
55 Kbps  
1 FPS  
1152 Kbps  
25 FPS  
553 Kbps  
12 FPS  
276 Kbps  
6 FPS  
138 Kbps  
3 FPS  
46 Kbps  
1 FPS  
922 Kbps  
25 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
691 Kbps  
25 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
461 Kbps  
25 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
English _73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (VGA)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
2507 Kbps  
17 FPS  
1327 Kbps  
9 FPS  
737 Kbps  
5 FPS  
442 Kbps  
3 FPS  
147 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1991 Kbps  
18 FPS  
1217 Kbps  
11 FPS  
664 Kbps  
6 FPS  
332 Kbps  
3 FPS  
111 Kbps  
1 FPS  
1659 Kbps  
18 FPS  
1106 Kbps  
12 FPS  
553 Kbps  
6 FPS  
276 Kbps  
3 FPS  
92 Kbps  
1 FPS  
1401 Kbps  
19 FPS  
885 Kbps  
12 FPS  
442 Kbps  
6 FPS  
221 Kbps  
3 FPS  
74 Kbps  
1 FPS  
1106 Kbps  
20 FPS  
664 Kbps  
12 FPS  
332 Kbps  
6 FPS  
166 Kbps  
3 FPS  
55 Kbps  
1 FPS  
968 Kbps  
21 FPS  
553 Kbps  
12 FPS  
276 Kbps  
6 FPS  
138 Kbps  
3 FPS  
46 Kbps  
1 FPS  
774 Kbps  
21 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
608 Kbps  
22 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
424 Kbps  
23 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
230 Kbps  
25 FPS  
111 Kbps  
12 FPS  
55 Kbps  
6 FPS  
28 Kbps  
3 FPS  
9 Kbps  
1 FPS  
74_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MPEG4 (CIF)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
1382 Kbps  
25 FPS  
664 Kbps  
12 FPS  
332 Kbps  
6 FPS  
166 Kbps  
3 FPS  
55 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
1152 Kbps  
25 FPS  
553 Kbps  
12 FPS  
276 Kbps  
6 FPS  
138 Kbps  
3 FPS  
46 Kbps  
1 FPS  
922 Kbps  
25 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
691 Kbps  
25 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
461 Kbps  
25 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
346 Kbps  
25 FPS  
166 Kbps  
12 FPS  
83 Kbps  
6 FPS  
41 Kbps  
3 FPS  
14 Kbps  
1 FPS  
288 Kbps  
25 FPS  
138 Kbps  
12 FPS  
69 Kbps  
6 FPS  
35 Kbps  
3 FPS  
12 Kbps  
1 FPS  
230 Kbps  
25 FPS  
111 Kbps  
12 FPS  
55 Kbps  
6 FPS  
28 Kbps  
3 FPS  
9 Kbps  
1 FPS  
173 Kbps  
25 FPS  
83 Kbps  
12 FPS  
41 Kbps  
6 FPS  
21 Kbps  
3 FPS  
7 Kbps  
1 FPS  
151 Kbps  
25 FPS  
73 Kbps  
12 FPS  
36 Kbps  
6 FPS  
18 Kbps  
3 FPS  
6 Kbps  
1 FPS  
English _75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
H.264 (CIF)  
Frame Rate  
25 FPS  
13 FPS  
6 FPS  
3 FPS  
1 FPS  
Quality  
922 Kbps  
25 FPS  
442 Kbps  
12 FPS  
221 Kbps  
6 FPS  
111 Kbps  
3 FPS  
37 Kbps  
1 FPS  
LEVEL10  
LEVEL9  
LEVEL8  
LEVEL7  
LEVEL6  
LEVEL5  
LEVEL4  
LEVEL3  
LEVEL2  
LEVEL1  
691 Kbps  
25 FPS  
332 Kbps  
12 FPS  
166 Kbps  
6 FPS  
83 Kbps  
3 FPS  
28 Kbps  
1 FPS  
576 Kbps  
25 FPS  
276 Kbps  
12 FPS  
138 Kbps  
6 FPS  
69 Kbps  
3 FPS  
23 Kbps  
1 FPS  
461 Kbps  
25 FPS  
221 Kbps  
12 FPS  
111 Kbps  
6 FPS  
55 Kbps  
3 FPS  
18 Kbps  
1 FPS  
346 Kbps  
25 FPS  
166 Kbps  
12 FPS  
83 Kbps  
6 FPS  
41 Kbps  
3 FPS  
14 Kbps  
1 FPS  
288 Kbps  
25 FPS  
138 Kbps  
12 FPS  
69 Kbps  
6 FPS  
35 Kbps  
3 FPS  
12 Kbps  
1 FPS  
230 Kbps  
25 FPS  
111 Kbps  
12 FPS  
55 Kbps  
6 FPS  
28 Kbps  
3 FPS  
9 Kbps  
1 FPS  
173 Kbps  
25 FPS  
83 Kbps  
12 FPS  
41 Kbps  
6 FPS  
21 Kbps  
3 FPS  
7 Kbps  
1 FPS  
115 Kbps  
25 FPS  
55 Kbps  
12 FPS  
28 Kbps  
6 FPS  
14 Kbps  
3 FPS  
5 Kbps  
1 FPS  
58 Kbps  
25 FPS  
28 Kbps  
12 FPS  
14 Kbps  
6 FPS  
7 Kbps  
3 FPS  
2 Kbps  
1 FPS  
76_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
PROBLEM  
SOLUTION  
y
y
Check to make sure that the camera’s Network settings are appropriate.  
Check to make sure that all network cables have been connected  
properly.  
y
y
y
If connected using DHCP, verify that the camera is able to acquire  
dynamic IP addresses without any problem.  
I can’t access the camera from a  
web browser.  
If connected using a DDNS URL, verify that the MAC address has been  
properly entered.  
If the camera is connected to a router, verify that port forwarding is  
properly configured.  
y
Connected Viewers become disconnected upon any change to camera or  
network configurations.  
Viewer got disconnected during  
monitoring.  
y
y
Check all network connections.  
If the camera is connected over an xDSL network, it’ s possible for  
Viewer to disconnect under poor network conditions.  
y
When you try to connect to the system using a tab browser, the same  
cookie information is shared, resulting in errors when connected.  
Therefore, instead of using a tab browser, open a new browser window  
to connect to the system.  
I cannot connect to the system  
using a tab browser of Internet  
Explorer 7.0.  
The camera connected to the  
network is not detected in the IP  
installer program.  
y
y
Turn off the firewall settings on your PC and then search the camera  
again.  
Check whether two or more cameras are set to a single multicast address  
instead of different addresses. If a single address is used for multiple  
cameras, the images may overlap.  
Images overlap.  
y
If the transmission method is set to multicast, check whether there is a  
router that supports multicast in the LAN the camera is connected to.  
No image appears.  
English _77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
PROBLEM  
SOLUTION  
y
Verify the settings in the following sequence:  
I enabled Motion Detection Feature  
under Motion Detection, but .jpg  
files are not getting sent over FTP/  
SMTP even after motion detection  
occurs at the FT camera.  
A. NTP must be properly configured.  
B. Motion Detection Feature must be enabled.  
C. Alarm Video Transmission must be enabled.  
D. Check for scheduling conflict.  
Is it possible to configure Motion  
Zone with Motion Detection  
Feature disabled?  
y
y
Yes. Motion Zone can be configured independently of whether or not  
Motion Detection Feature is in use.  
A motion event took place but  
didn’t trigger an alarm.  
Check alarm output port settings.  
78_ appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GPL/LGPL SOFTWARE LICENSE  
This product uses open-source software distributed under the terms of GPL and LGPL.  
And you can visit at www.samsungsecurity.com to get the source codes of the following GPL  
and LGPL software used for this product.  
y
GPL S/W  
Base Kernel, Busybox, Sysvinit, dosfstools  
LGPL S/W  
gLibc, Inetutils  
-
y
-
want it, that you can change the software  
or use pieces of it in new free programs ;  
and that you know you can do these things.  
GNU GENERAL PUBLIC LICENSE  
Version 2, June 1991  
Copyright (C)1989, 1991 Free Software  
Foundation, Inc.  
51 Franklin Street,Fifth Floor, Boston,  
MA 02110-1301, USA  
To protect your rights, we need to make  
restrictions that forbid anyone to deny you  
these rights or to ask you to surrender the  
rights. These restrictions translate to certain  
responsibilities for you if you distribute  
copies of the software, or if you modify it.  
Everyone is permitted to copy and  
distribute verbatim copies of this license  
document, but changing it is not allowed.  
For example, if you distribute copies of  
such a program, whether gratis or for a fee,  
you must give the recipients all the rights  
that you have.  
Preamble  
The licenses for most software are designed  
to take away your freedom to share and  
change it. By contrast, the GNU General  
Public License is intended to guarantee  
your freedom to share and change free  
software-- to make sure the software is free  
for all its users.  
You must make sure that they, too, receive or  
can get the source code. And you must show  
them these terms so they know their rights.  
We protect your rights with two steps :  
(1)copyright the software, and (2)offer  
you this license which gives you legal  
permission to copy, distribute and/or  
modify the software.  
This General Public License applies to most  
of the Free Software Foundation's software  
and to any other program whose authors  
commit to using it. (Some other Free Software  
Foundation software is covered by the GNU  
Lesser General Public License instead.) You  
can apply it to your programs, too.  
Also, for each author's protection and ours,  
we want to make certain that everyone  
understands that there is no warranty for  
this free software. If the software is modified  
by someone else and passed on, we want  
its recipients to know that what they have  
is not the original, so that any problems  
introduced by others will not reflect on the  
original authors' reputations.  
When we speak of free software, we are  
referring to freedom, not price.  
Our General Public Licenses are designed  
to make sure that you have the freedom  
to distribute copies of free software (and  
charge for this service if you wish), that you  
receive source code or can get it if you  
Finally, any free program is threatened  
constantly by software patents. We wish  
Download from Www.Somanuals.com. All Manuals Search And Download.  
to avoid the danger that redistributors of a  
free program will individually obtain patent  
licenses, in effect making the program  
proprietary. To prevent this, we have made  
it clear that any patent must be licensed for  
everyone's free use or not licensed at all.  
recipients of the Program a copy of this  
License along with the Program.  
You may charge a fee for the physical  
act of transferring a copy, and you may  
at your option offer warranty protection  
in exchange for a fee.  
The precise terms and conditions for  
copying, distribution and modification follow.  
2. You may modify your copy or copies  
of the Program or any portion of it,  
thus forming a work based on the  
Program, and copy and distribute such  
modifications or work under the terms of  
Section 1 above, provided that you also  
meet all of these conditions :  
TERMS AND CONDITIONS FOR  
COPYING, DISTRIBUTION AND  
MODIFICATION  
0. This License applies to any program  
or other work which contains a notice  
placed by the copyright holder saying it  
may be distributed under the terms of  
this General Public License.  
The "Program", below, refers to any such  
program or work, and a "work based on  
the Program" means either the Program  
or any derivative work under copyright  
law : that is to say, a work containing the  
Program or a portion of it, either verbatim  
or with modifications and/or translated  
into another language. (Hereinafter,  
translation is included without limitation  
in the term "modification".) Each licensee  
is addressed as "you".  
Activities other than copying, distribution  
and modification are not covered by  
this License ; they are outside its scope.  
The act of running the Program is not  
restricted, and the output from the  
Program is covered only if its contents  
constitute a work based on the Program  
(independent of having been made by  
running the Program). Whether that is  
true depends on what the Program does.  
a) You must cause the modified files to  
carry prominent notices stating that  
you changed the files and the date of  
any change.  
b) You must cause any work that you  
distribute or publish, that in whole or  
in part contains or is derived from the  
Program or any part thereof, to be  
licensed as a whole at no charge to  
all third parties under the terms of this  
License.  
c) If the modified program normally  
reads commands interactively  
when run,you must cause it, when  
started running for such interactive  
use in the most ordinary way, to  
print or display an announcement  
including an appropriate copyright  
notice and a notice that there is no  
warranty (or else, saying that you  
provide a warranty) and that users  
may redistribute the program under  
these conditions, and telling the user  
how to view a copy of this License.  
(Exception:if the Program itself is  
interactive but does not normally print  
such an announcement, your work  
based on the Program is not required  
to print an announcement.)  
1. You may copy and distribute verbatim  
copies of the Program's source code as  
you receive it, in any medium, provided  
that you conspicuously and appropriately  
publish on each copy an appropriate  
copyright notice and disclaimer of  
warranty; keep intact all the notices that  
refer to this License and to the absence  
of any warranty ; and give any other  
These requirements apply to the modified  
work as a whole. If identifiable sections  
of that work are not derived from  
the Program, and can be reasonably  
Download from Www.Somanuals.com. All Manuals Search And Download.  
considered independent and separate  
works in themselves, then this License, and  
its terms, do not apply to those sections  
when you distribute them as separate  
works. But when you distribute the same  
sections as part of a whole which is a work  
based on the Program, the distribution  
of the whole must be on the terms of this  
License, whose permissions for other  
licensees extend to the entire whole, and  
thus to each and every part regardless of  
who wrote it.  
c) Accompany it with the information  
you received as to the offer to  
distribute corresponding source code.  
(This alternative is allowed only for  
noncommercial distribution and only  
if you received the program in object  
code or executable form with such  
an offer, in accord with Subsection b  
above.)  
The source code for a work means the  
preferred form of the work for making  
modifications to it. For an executable work,  
complete source code means all the source  
code for all modules it contains, plus any  
associated interface definition files, plus  
the scripts used to control compilation and  
installation of the executable. However,  
as a special exception, the source code  
distributed need not include anything that  
is normally distributed (in either source or  
binary form)with the major components  
(compiler, kernel, and so on)of the operating  
system on which the executable runs,  
unless that component itself accompanies  
the executable.  
Thus, it is not the intent of this section to  
claim rights or contest your rights to work  
written entirely by you ; rather, the intent is to  
exercise the right to control the distribution  
of derivative or collective works based on  
the Program. In addition, mere aggregation  
of another work not based on the Program  
with the Program (or with a work based on  
the Program)on a volume of a storage or  
distribution medium does not bring the other  
work under the scope of this License.  
3. You may copy and distribute the  
Program (or a work based on it, under  
Section 2)in object code or executable  
form under the terms of Sections 1 and  
2 above provided that you also do one of  
the following :  
If distribution of executable or object code  
is made by offering access to copy from a  
designated place, then offering equivalent  
access to copy the source code from the  
same place counts as distribution of the  
source code, even though third parties are  
not compelled to copy the source along  
with the object code.  
a) Accompany it with the complete  
corresponding machine-readable  
source code, which must be  
distributed under the terms of  
Sections 1 and 2 above on a medium  
customarily used for software  
interchange ; or,  
4. You may not copy, modify, sublicense,  
or distribute the Program except as  
expressly provided under this License.  
Any attempt otherwise to copy, modify,  
sublicense or distribute the Program is  
void, and will automatically terminate  
your rights under this License.  
However, parties who have received  
copies, or rights, from you under this  
License will not have their licenses  
terminated so long as such parties  
remain in full compliance.  
b) Accompany it with a written offer,  
valid for at least three years, to give  
any third party, for a charge no  
more than your cost of physically  
performing source distribution, a  
complete machinereadable copy  
of the corresponding source code,  
to be distributed under the terms  
of Sections 1 and 2 above on a  
medium customarily used for software  
interchange ; or,  
5. You are not required to accept this  
License, since you have not signed it.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
However, nothing else grants you  
a whole is intended to apply in other  
permission to modify or distribute the  
Program or its derivative works.  
circumstances. It is not the purpose of  
this section to induce you to infringe any  
patents or other property right claims or  
to contest validity of any such claims; this  
section has the sole purpose of protecting  
the integrity of the free software distribution  
system, which is implemented by public  
license practices. Many people have made  
generous contributions to the wide range  
of software distributed through that system  
in reliance on consistent application of that  
system ; it is up to the author/donor to  
decide if he or she is willing to distribute  
software through any other system and a  
licensee cannot impose that choice.  
These actions are prohibited by law if you  
do not accept this License.Therefore, by  
modifying or distributing the Program (or  
any work based on the Program), you  
indicate your acceptance of this License  
to do so, and all its terms and conditions  
for copying, distributing or modifying the  
Program or works based on it.  
6. Each time you redistribute the Program  
(or any work based on the Program),  
the recipient automatically receives a  
license from the original licensor to copy,  
distribute or modify the Program subject  
to these terms and conditions.  
You may not impose any further  
restrictions on the recipients' exercise of  
the rights granted herein.  
This section is intended to make thoroughly  
clear what is believed to be a consequence  
of the rest of this License.  
8. If the distribution and/or use of the  
Program is restricted in certain countries  
either by patents or by copyrighted  
interfaces, the original copyright holder  
who places the Program under this  
License may add an explicit geographical  
distribution limitation excluding those  
countries,so that distribution is permitted  
only in or among countries not thus  
excluded. In such case, this License  
incorporates the limitation as if written in  
the body of this License.  
You are not responsible for enforcing  
compliance by third parties to this  
License.  
7. If, as a consequence of a court judgment  
or allegation of patent infringement or for  
any other reason (not limited to patent  
issues), conditions are imposed on you  
(whether by court order, agreement or  
otherwise)that contradict the conditions  
of this License, they do not excuse you  
from the conditions of this License. If  
you cannot distribute so as to satisfy  
simultaneously your obligations under  
this License and any other pertinent  
obligations, then as a consequence you  
may not distribute the Program at all.  
For example, if a patent license would  
not permit royalty-free redistribution of  
the Program by all those who receive  
copies directly or indirectly through you,  
then the only way you could satisfy both  
it and this License would be to refrain  
entirely from distribution of the Program.  
9. The Free Software Foundation may  
publish revised and/or new versions of  
the General Public License from time to  
time. Such new versions will be similar  
in spirit to the present version, but may  
differ in detail to address new problems  
or concerns.  
Each version is given a distinguishing  
version number. If the Program specifies  
a version number of this License which  
applies to it and "any later version", you  
have the option of following the terms and  
conditions either of that version or of any  
later version published by the Free Software  
Foundation. If the Program does not specify  
a version number of this License, you may  
If any portion of this section is held invalid  
or unenforceable under any particular  
circumstance, the balance of the section  
is intended to apply and the section as  
Download from Www.Somanuals.com. All Manuals Search And Download.  
choose any version ever published by the  
Free Software Foundation.  
USE OR INABILITY TO USE THE  
PROGRAM (INCLUDING BUT NOT  
LIMITED TO LOSS OF DATA OR DATA  
BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU  
OR THIRD PARTIES OR A FAILURE  
OF THE PROGRAM TO OPERATE  
WITH ANY OTHER PROGRAMS),  
EVEN IF SUCH HOLDER OR OTHER  
PARTY HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES.  
10. If you wish to incorporate parts of the  
Program into other free programs  
whose distribution conditions are  
different, write to the author to ask  
for permission. For software which  
is copyrighted by the Free Software  
Foundation,write to the Free Software  
Foundation ; we sometimes make  
exceptions for this. Our decision will be  
guided by the two goals of preserving  
the free status of all derivatives of our  
free software and of promoting the  
sharing and reuse of software generally.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your  
New Programs  
NO WARRANTY  
If you develop a new program, and you  
want it to be of the greatest possible use to  
the public, the best way to achieve this is to  
make it free software which everyone can  
redistribute and change under these terms.  
11. BECAUSE THE PROGRAM IS  
LICENSED FREE OF CHARGE,  
THERE IS NO WARRANTY FOR  
THE PROGRAM, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW.  
EXCEPT WHEN OTHERWISE STATED IN  
WRITING THE COPYRIGHT HOLDERS  
AND/OR OTHER PARTIES PROVIDE  
THE PROGRAM "ASIS" WITHOUT  
WARRANTY OF ANY KIND, EITHER  
EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR  
PURPOSE. THE ENTIRE RISK AS TO  
THE QUALITY AND PERFORMANCE OF  
THE PROGRAM IS WITH YOU. SHOULD  
THE PROGRAMPROVE DEFECTIVE,  
YOU ASSUME THE COST OF ALL  
NECESSARY SERVICING, REPAIR OR  
CORRECTION.  
To do so, attach the following notices to  
the program. It is safest to attach them  
to the start of each source file to most  
effectively convey the exclusion of warranty  
; and each file should have at least the  
"copyright" line and a pointer to where the  
full notice is found.  
one line to give the program's name and an  
idea of what it does.  
Copyright (C)yyyy name of author  
This program is free software ; you can  
redistribute it and/or modify it under the  
terms of the GNU General Public License as  
published by the Free Software Foundation  
; either version 2 of the License, or (at your  
option)any later version.  
This program is distributed in the hope  
that it will be useful, but WITHOUT ANY  
WARRANTY ; without even the implied  
warranty of MERCHANTABILITY or  
FITNESS FOR A PARTICULAR PURPOSE.  
See the GNU General Public License for  
more details.  
12. IN NO EVENT UNLESS REQUIRED  
BY APPLICABLE LAW OR AGREED  
TO IN WRITING WILL ANY  
COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY  
AND/OR REDISTRIBUTE DAMAGES,  
INCLUDING ANY GENERAL, SPECIAL,  
INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF THE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You should have received a copy of the  
GNU General Public License along with this  
program ; if not, write to the Free Software  
Foundation, Inc.,51 Franklin Street, Fifth  
Floor, Boston, MA 02110-1301, USA.  
GNU GENERAL PUBLIC LICENSE  
Version 3, 29 June 2007  
Copyright © 2007 Free Software Foundation,  
Inc. <http://fsf.org/>  
Also add information on how to contact you  
by electronic and paper mail. If the program  
is interactive, make it output a short notice  
like this when it starts in an interactive  
mode :  
Everyone is permitted to copy and distribute  
verbatim copies of this license document, but  
changing it is not allowed.  
Gnomovision version 69,  
Preamble  
Copyright (C) year name of author  
The GNU General Public License is a free,  
copyleft license for software and other kinds  
of works.  
Gnomovision comes with ABSOLUTELY  
NO  
WARRANTY ; for details type ‘show w’.  
This is free software, and you are welcome  
to redistribute it under certain conditions ;  
type ‘show c’ for details.  
The licenses for most software and other  
practical works are designed to take away  
your freedom to share and change the works.  
By contrast, the GNU General Public License  
is intended to guarantee your freedom to  
share and change all versions of a program--  
to make sure it remains free software for all its  
users. We, the Free Software Foundation, use  
the GNU General Public License for most of  
our software; it applies also to any other work  
released this way by its authors. You can  
apply it to your programs, too.  
The hypothetical commands ‘show w’ and  
‘show c’ should show the appropriate parts  
of the General Public License. Of course,  
the commands you use may be called  
something other than ‘show w’ and ‘show  
c’ ; they could even be mouse-clicks or  
menu items-- whatever suits your program.  
You should also get your employer (if you  
work as a programmer)or your school, if  
any, to sign a "copyright disclaimer" for the  
program,if necessary. Here is a sample ;  
alter the names:  
When we speak of free software, we are  
referring to freedom, not price. Our General  
Public Licenses are designed to make sure  
that you have the freedom to distribute copies  
of free software (and charge for them if you  
wish), that you receive source code or can  
get it if you want it, that you can change  
the software or use pieces of it in new free  
programs, and that you know you can do  
these things.  
Yoyodyne, Inc.,hereby disclaims all  
copyright interest in the program ‘  
Gnomovision’ (which makes passes at  
compilers) written by James Hacker.  
signature of Ty Coon, 1 April 1989 Ty  
Coon, President of Vice This General Public  
License does not permit incorporating your  
program into proprietary programs. If your  
program is a subroutine library, you may  
consider it more useful to permit linking  
proprietary applications with the library. If  
this is what you want to do, use the GNU  
Lesser General Public License instead of  
this License.  
To protect your rights, we need to prevent  
others from denying you these rights or asking  
you to surrender the rights. Therefore, you  
have certain responsibilities if you distribute  
copies of the software, or if you modify it:  
responsibilities to respect the freedom of  
others.  
For example, if you distribute copies of such a  
program, whether gratis or for a fee, you must  
pass on to the recipients the same freedoms  
Download from Www.Somanuals.com. All Manuals Search And Download.  
that you received. You must make sure that  
they, too, receive or can get the source code.  
And you must show them these terms so they  
know their rights.  
TERMS AND CONDITIONS  
0. Definitions.  
“This License” refers to version 3 of the GNU  
General Public License.  
Developers that use the GNU GPL protect  
your rights with two steps: (1) assert copyright  
on the software, and (2) offer you this License  
giving you legal permission to copy, distribute  
and/or modify it.  
“Copyright” also means copyright-like laws  
that apply to other kinds of works, such as  
semiconductor masks.  
“The Program” refers to any copyrightable  
work licensed under this License. Each  
licensee is addressed as “you”. “Licensees”  
and “recipients” may be individuals or  
organizations.  
For the developers' and authors' protection,  
the GPL clearly explains that there is no  
warranty for this free software. For both users'  
and authors' sake, the GPL requires that  
modified versions be marked as changed,  
so that their problems will not be attributed  
erroneously to authors of previous versions.  
To modify” a work means to copy from  
or adapt all or part of the work in a fashion  
requiring copyright permission, other than the  
making of an exact copy. The resulting work  
is called a “modified version” of the earlier  
work or a work “based on” the earlier work.  
Some devices are designed to deny users  
access to install or run modified versions  
of the software inside them, although the  
manufacturer can do so. This is fundamentally  
incompatible with the aim of protecting  
users' freedom to change the software. The  
systematic pattern of such abuse occurs  
in the area of products for individuals to  
use, which is precisely where it is most  
unacceptable. Therefore, we have designed  
this version of the GPL to prohibit the practice  
for those products. If such problems arise  
substantially in other domains, we stand ready  
to extend this provision to those domains  
in future versions of the GPL, as needed to  
protect the freedom of users.  
A “covered work” means either the unmodified  
Program or a work based on the Program.  
To propagate” a work means to do anything  
with it that, without permission, would  
make you directly or secondarily liable for  
infringement under applicable copyright  
law, except executing it on a computer  
or modifying a private copy. Propagation  
includes copying, distribution (with or without  
modification), making available to the public,  
and in some countries other activities as well.  
To convey” a work means any kind of  
propagation that enables other parties to  
make or receive copies. Mere interaction with  
a user through a computer network, with no  
transfer of a copy, is not conveying.  
Finally, every program is threatened constantly  
by software patents. States should not allow  
patents to restrict development and use of  
software on general-purpose computers,  
but in those that do, we wish to avoid the  
special danger that patents applied to a free  
program could make it effectively proprietary.  
To prevent this, the GPL assures that patents  
cannot be used to render the program non-  
free.  
An interactive user interface displays  
“Appropriate Legal Notices” to the extent  
that it includes a convenient and prominently  
visible feature that (1) displays an appropriate  
copyright notice, and (2) tells the user that  
there is no warranty for the work (except  
to the extent that warranties are provided),  
that licensees may convey the work under  
this License, and how to view a copy of this  
License.  
The precise terms and conditions for copying,  
distribution and modification follow.  
If the interface presents a list of user  
commands or options, such as a menu, a  
prominent item in the list meets this criterion.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Source Code.  
The Corresponding Source need not  
include anything that users can regenerate  
automatically from other parts of the  
Corresponding Source.  
The “source code” for a work means the  
preferred form of the work for making  
modifications to it. “Object code” means any  
non-source form of a work.  
The Corresponding Source for a work in  
source code form is that same work.  
A “Standard Interface” means an interface  
that either is an official standard defined  
by a recognized standards body, or, in the  
case of interfaces specified for a particular  
programming language, one that is widely  
used among developers working in that  
language.  
2. Basic Permissions.  
All rights granted under this License are  
granted for the term of copyright on the  
Program, and are irrevocable provided the  
stated conditions are met. This License  
explicitly affirms your unlimited permission to  
run the unmodified Program. The output from  
running a covered work is covered by this  
License only if the output, given its content,  
constitutes a covered work. This License  
acknowledges your rights of fair use or other  
equivalent, as provided by copyright law.  
The “System Libraries” of an executable  
work include anything, other than the work  
as a whole, that (a) is included in the normal  
form of packaging a Major Component, but  
which is not part of that Major Component,  
and (b) serves only to enable use of the  
work with that Major Component, or to  
implement a Standard Interface for which  
an implementation is available to the public  
in source code form. A “Major Component”,  
in this context, means a major essential  
component (kernel, window system, and so  
on) of the specific operating system (if any) on  
which the executable work runs, or a compiler  
used to produce the work, or an object code  
interpreter used to run it.  
You may make, run and propagate covered  
works that you do not convey, without  
conditions so long as your license otherwise  
remains in force. You may convey covered  
works to others for the sole purpose of having  
them make modifications exclusively for you,  
or provide you with facilities for running those  
works, provided that you comply with the  
terms of this License in conveying all material  
for which you do not control copyright. Those  
thus making or running the covered works for  
you must do so exclusively on your behalf,  
under your direction and control, on terms  
that prohibit them from making any copies  
of your copyrighted material outside their  
relationship with you.  
The “Corresponding Source” for a work  
in object code form means all the source  
code needed to generate, install, and (for  
an executable work) run the object code  
and to modify the work, including scripts  
to control those activities. However, it does  
not include the work's System Libraries, or  
general-purpose tools or generally available  
free programs which are used unmodified in  
performing those activities but which are not  
part of the work. For example, Corresponding  
Source includes interface definition files  
associated with source files for the work,  
and the source code for shared libraries and  
dynamically linked subprograms that the work  
is specifically designed to require, such as by  
intimate data communication or control flow  
between those subprograms and other parts  
of the work.  
Conveying under any other circumstances is  
permitted solely under the conditions stated  
below. Sublicensing is not allowed; section 10  
makes it unnecessary.  
3. Protecting Users' Legal Rights From  
Anti-Circumvention Law.  
No covered work shall be deemed part of an  
effective technological measure under any  
applicable law fulfilling obligations under article  
11 of the WIPO copyright treaty adopted on  
20 December 1996, or similar laws prohibiting  
or restricting circumvention of such measures.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When you convey a covered work, you waive  
any legal power to forbid circumvention of  
technological measures to the extent such  
circumvention is effected by exercising rights  
under this License with respect to the covered  
work, and you disclaim any intention to limit  
operation or modification of the work as a  
means of enforcing, against the work's users,  
your or third parties' legal rights to forbid  
circumvention of technological measures.  
This License gives no permission to  
license the work in any other way, but it  
does not invalidate such permission if you  
have separately received it.  
ƒ d) If the work has interactive user interfaces,  
each must display Appropriate Legal  
Notices; however, if the Program has  
interactive interfaces that do not display  
Appropriate Legal Notices, your work  
need not make them do so.  
4. Conveying Verbatim Copies.  
A compilation of a covered work with other  
separate and independent works, which are  
not by their nature extensions of the covered  
work, and which are not combined with it  
such as to form a larger program, in or on a  
volume of a storage or distribution medium, is  
called an “aggregate” if the compilation and  
its resulting copyright are not used to limit  
the access or legal rights of the compilation's  
users beyond what the individual works  
permit. Inclusion of a covered work in an  
aggregate does not cause this License to  
apply to the other parts of the aggregate.  
You may convey verbatim copies of the  
Program's source code as you receive it, in  
any medium, provided that you conspicuously  
and appropriately publish on each copy an  
appropriate copyright notice; keep intact  
all notices stating that this License and any  
non-permissive terms added in accord with  
section 7 apply to the code; keep intact all  
notices of the absence of any warranty; and  
give all recipients a copy of this License along  
with the Program.  
You may charge any price or no price for  
each copy that you convey, and you may offer  
support or warranty protection for a fee.  
6. Conveying Non-Source Forms.  
You may convey a covered work in object  
code form under the terms of sections 4 and 5,  
provided that you also convey the machine-  
readable Corresponding Source under the  
terms of this License, in one of these ways:  
5. Conveying Modified Source Versions.  
You may convey a work based on the  
Program, or the modifications to produce it  
from the Program, in the form of source code  
under the terms of section 4, provided that  
you also meet all of these conditions:  
ƒ a) Convey the object code in, or embodied  
in, a physical product (including a physical  
distribution medium), accompanied by the  
Corresponding Source fixed on a durable  
physical medium customarily used for  
software interchange.  
ƒ a) The work must carry prominent notices  
stating that you modified it, and giving a  
relevant date.  
ƒ b) The work must carry prominent notices  
stating that it is released under this  
License and any conditions added under  
section 7. This requirement modifies the  
requirement in section 4 to “keep intact  
all notices”.  
Convey the object code in, or embodied  
in, a physical product (including a physical  
distribution medium), accompanied by  
a written offer, valid for at least three  
years and valid for as long as you offer  
spare parts or customer support for  
that product model, to give anyone who  
possesses the object code either (1) a  
copy of the Corresponding Source for all  
the software in the product that is covered  
by this License, on a durable physical  
medium customarily used for software  
interchange, for a price no more than your  
ƒ b)  
ƒ c) You must license the entire work, as a  
whole, under this License to anyone who  
comes into possession of a copy. This  
License will therefore apply, along with  
any applicable section 7 additional terms,  
to the whole of the work, and all its parts,  
regardless of how they are packaged.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
reasonable cost of physically performing  
this conveying of source, or (2) access to  
copy the Corresponding Source from a  
network server at no charge.  
resolved in favor of coverage. For a particular  
product received by a particular user,  
“normally used” refers to a typical or common  
use of that class of product, regardless of  
the status of the particular user or of the way  
in which the particular user actually uses, or  
expects or is expected to use, the product.  
A product is a consumer product regardless  
of whether the product has substantial  
commercial, industrial or non-consumer uses,  
unless such uses represent the only significant  
mode of use of the product.  
ƒ c) Convey individual copies of the object  
code with a copy of the written offer to  
provide the Corresponding Source. This  
alternative is allowed only occasionally  
and noncommercially, and only if you  
received the object code with such an  
offer, in accord with subsection 6b.  
ƒ d) Convey the object code by offering  
access from a designated place (gratis or  
for a charge), and offer equivalent access  
to the Corresponding Source in the same  
way through the same place at no further  
charge. You need not require recipients  
to copy the Corresponding Source along  
with the object code. If the place to copy  
the object code is a network server,  
the Corresponding Source may be on  
a different server (operated by you or  
a third party) that supports equivalent  
copying facilities, provided you maintain  
clear directions next to the object code  
saying where to find the Corresponding  
Source. Regardless of what server hosts  
the Corresponding Source, you remain  
obligated to ensure that it is available  
for as long as needed to satisfy these  
requirements.  
“Installation Information” for a User  
Product means any methods, procedures,  
authorization keys, or other information  
required to install and execute modified  
versions of a covered work in that User  
Product from a modified version of its  
Corresponding Source. The information  
must suffice to ensure that the continued  
functioning of the modified object code is in  
no case prevented or interfered with solely  
because modification has been made.  
If you convey an object code work under this  
section in, or with, or specifically for use in,  
a User Product, and the conveying occurs  
as part of a transaction in which the right of  
possession and use of the User Product is  
transferred to the recipient in perpetuity or for  
a fixed term (regardless of how the transaction  
is characterized), the Corresponding Source  
conveyed under this section must be  
accompanied by the Installation Information.  
But this requirement does not apply if neither  
you nor any third party retains the ability  
to install modified object code on the User  
Product (for example, the work has been  
ƒ e) Convey the object code using peer-to-  
peer transmission, provided you inform  
other peers where the object code and  
Corresponding Source of the work are  
being offered to the general public at no  
charge under subsection 6d.  
installed in ROM).  
A separable portion of the object code,  
whose source code is excluded from the  
Corresponding Source as a System Library,  
need not be included in conveying the object  
code work.  
The requirement to provide Installation  
Information does not include a requirement to  
continue to provide support service, warranty,  
or updates for a work that has been modified  
or installed by the recipient, or for the User  
Product in which it has been modified or  
installed. Access to a network may be  
denied when the modification itself materially  
and adversely affects the operation of the  
network or violates the rules and protocols for  
communication across the network.  
A “User Product” is either (1) a “consumer  
product”, which means any tangible personal  
property which is normally used for personal,  
family, or household purposes, or (2) anything  
designed or sold for incorporation into a  
dwelling. In determining whether a product is  
a consumer product, doubtful cases shall be  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Corresponding Source conveyed, and  
Installation Information provided, in accord  
with this section must be in a format  
that is publicly documented (and with an  
implementation available to the public in  
source code form), and must require no  
special password or key for unpacking,  
reading or copying.  
reasonable ways as different from the  
original version; or  
ƒ d) Limiting the use for publicity purposes  
of names of licensors or authors of the  
material; or  
ƒ e) Declining to grant rights under trademark  
law for use of some trade names,  
trademarks, or service marks; or  
7. Additional Terms.  
ƒ f) Requiring indemnification of licensors and  
authors of that material by anyone who  
conveys the material (or modified versions  
of it) with contractual assumptions of  
liability to the recipient, for any liability that  
these contractual assumptions directly  
impose on those licensors and authors.  
“Additional permissions” are terms that  
supplement the terms of this License by  
making exceptions from one or more of its  
conditions. Additional permissions that are  
applicable to the entire Program shall be  
treated as though they were included in this  
License, to the extent that they are valid under  
applicable law. If additional permissions apply  
only to part of the Program, that part may be  
used separately under those permissions,  
but the entire Program remains governed by  
this License without regard to the additional  
permissions.  
All other non-permissive additional terms  
are considered “further restrictions” within  
the meaning of section 10. If the Program  
as you received it, or any part of it, contains  
a notice stating that it is governed by this  
License along with a term that is a further  
restriction, you may remove that term. If a  
license document contains a further restriction  
but permits relicensing or conveying under  
this License, you may add to a covered work  
material governed by the terms of that license  
document, provided that the further restriction  
does not survive such relicensing or conveying.  
When you convey a copy of a covered work,  
you may at your option remove any additional  
permissions from that copy, or from any part  
of it. (Additional permissions may be written  
to require their own removal in certain cases  
when you modify the work.) You may place  
additional permissions on material, added by  
you to a covered work, for which you have or  
can give appropriate copyright permission.  
If you add terms to a covered work in accord  
with this section, you must place, in the  
relevant source files, a statement of the  
additional terms that apply to those files, or a  
notice indicating where to find the applicable  
terms.  
Notwithstanding any other provision of this  
License, for material you add to a covered  
work, you may (if authorized by the copyright  
holders of that material) supplement the terms  
of this License with terms:  
Additional terms, permissive or non-  
permissive, may be stated in the form of  
a separately written license, or stated as  
exceptions; the above requirements apply  
either way.  
ƒ a) Disclaiming warranty or limiting liability  
differently from the terms of sections 15  
and 16 of this License; or  
8. Termination.  
ƒ b) Requiring preservation of specified  
reasonable legal notices or author  
attributions in that material or in the  
Appropriate Legal Notices displayed by  
works containing it; or  
You may not propagate or modify a covered  
work except as expressly provided under this  
License. Any attempt otherwise to propagate  
or modify it is void, and will automatically  
terminate your rights under this License  
(including any patent licenses granted under  
the third paragraph of section 11).  
ƒ c) Prohibiting misrepresentation of the origin  
of that material, or requiring that modified  
versions of such material be marked in  
Download from Www.Somanuals.com. All Manuals Search And Download.  
However, if you cease all violation of this  
License, then your license from a particular  
copyright holder is reinstated (a) provisionally,  
unless and until the copyright holder explicitly  
and finally terminates your license, and (b)  
permanently, if the copyright holder fails to  
notify you of the violation by some reasonable  
means prior to 60 days after the cessation.  
An “entity transaction” is a transaction  
transferring control of an organization, or  
substantially all assets of one, or subdividing  
an organization, or merging organizations.  
If propagation of a covered work results  
from an entity transaction, each party to that  
transaction who receives a copy of the work  
also receives whatever licenses to the work  
the party's predecessor in interest had or  
could give under the previous paragraph, plus  
a right to possession of the Corresponding  
Source of the work from the predecessor in  
interest, if the predecessor has it or can get it  
with reasonable efforts.  
Moreover, your license from a particular  
copyright holder is reinstated permanently  
if the copyright holder notifies you of the  
violation by some reasonable means, this  
is the first time you have received notice of  
violation of this License (for any work) from  
that copyright holder, and you cure the  
violation prior to 30 days after your receipt of  
the notice.  
You may not impose any further restrictions on  
the exercise of the rights granted or affirmed  
under this License. For example, you may not  
impose a license fee, royalty, or other charge  
for exercise of rights granted under this License,  
and you may not initiate litigation (including a  
cross-claim or counterclaim in a lawsuit) alleging  
that any patent claim is infringed by making,  
using, selling, offering for sale, or importing the  
Program or any portion of it.  
Termination of your rights under this section  
does not terminate the licenses of parties  
who have received copies or rights from you  
under this License. If your rights have been  
terminated and not permanently reinstated,  
you do not qualify to receive new licenses for  
the same material under section 10.  
11. Patents.  
9. Acceptance Not Required for Having  
Copies.  
A “contributor” is a copyright holder who  
authorizes use under this License of the  
Program or a work on which the Program is  
based. The work thus licensed is called the  
contributor's “contributor version”.  
You are not required to accept this License  
in order to receive or run a copy of the  
Program. Ancillary propagation of a covered  
work occurring solely as a consequence of  
using peer-to-peer transmission to receive a  
copy likewise does not require acceptance.  
However, nothing other than this License  
grants you permission to propagate or modify  
any covered work. These actions infringe  
copyright if you do not accept this License.  
Therefore, by modifying or propagating a  
covered work, you indicate your acceptance  
of this License to do so.  
A contributor's “essential patent claims” are  
all patent claims owned or controlled by the  
contributor, whether already acquired or  
hereafter acquired, that would be infringed by  
some manner, permitted by this License, of  
making, using, or selling its contributor version,  
but do not include claims that would be infringed  
only as a consequence of further modification  
of the contributor version. For purposes of this  
definition, “control” includes the right to grant  
patent sublicenses in a manner consistent with  
the requirements of this License.  
10. Automatic Licensing of Downstream  
Recipients.  
Each time you convey a covered work, the  
recipient automatically receives a license  
from the original licensors, to run, modify  
and propagate that work, subject to this  
License. You are not responsible for enforcing  
compliance by third parties with this License.  
Each contributor grants you a non-exclusive,  
worldwide, royalty-free patent license under  
the contributor's essential patent claims, to  
make, use, sell, offer for sale, import and  
otherwise run, modify and propagate the  
contents of its contributor version.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In the following three paragraphs, a “patent  
license” is any express agreement or  
software, under which you make payment to  
the third party based on the extent of your  
activity of conveying the work, and under  
which the third party grants, to any of the  
parties who would receive the covered work  
from you, a discriminatory patent license (a) in  
connection with copies of the covered work  
conveyed by you (or copies made from those  
copies), or (b) primarily for and in connection  
with specific products or compilations that  
contain the covered work, unless you entered  
into that arrangement, or that patent license  
was granted, prior to 28 March 2007.  
commitment, however denominated, not  
to enforce a patent (such as an express  
permission to practice a patent or covenant  
not to sue for patent infringement). To grant”  
such a patent license to a party means to  
make such an agreement or commitment not  
to enforce a patent against the party.  
If you convey a covered work, knowingly  
relying on a patent license, and the  
Corresponding Source of the work is not  
available for anyone to copy, free of charge  
and under the terms of this License, through  
a publicly available network server or other  
readily accessible means, then you must  
either (1) cause the Corresponding Source  
to be so available, or (2) arrange to deprive  
yourself of the benefit of the patent license  
for this particular work, or (3) arrange, in a  
manner consistent with the requirements of  
this License, to extend the patent license to  
downstream recipients. “Knowingly relying”  
means you have actual knowledge that, but  
for the patent license, your conveying the  
covered work in a country, or your recipient's  
use of the covered work in a country, would  
infringe one or more identifiable patents in that  
country that you have reason to believe are  
Nothing in this License shall be construed  
as excluding or limiting any implied license  
or other defenses to infringement that may  
otherwise be available to you under applicable  
patent law.  
12. No Surrender of Others' Freedom.  
If conditions are imposed on you (whether  
by court order, agreement or otherwise) that  
contradict the conditions of this License, they  
do not excuse you from the conditions of  
this License. If you cannot convey a covered  
work so as to satisfy simultaneously your  
obligations under this License and any other  
pertinent obligations, then as a consequence  
you may not convey it at all. For example, if  
you agree to terms that obligate you to collect  
a royalty for further conveying from those  
to whom you convey the Program, the only  
way you could satisfy both those terms and  
this License would be to refrain entirely from  
conveying the Program.  
valid.  
If, pursuant to or in connection with a single  
transaction or arrangement, you convey, or  
propagate by procuring conveyance of, a  
covered work, and grant a patent license to  
some of the parties receiving the covered  
work authorizing them to use, propagate,  
modify or convey a specific copy of the  
covered work, then the patent license you  
grant is automatically extended to all  
recipients of the covered work and works  
based on it.  
13. Use with the GNU Affero General  
Public License.  
Notwithstanding any other provision of  
this License, you have permission to link  
or combine any covered work with a work  
licensed under version 3 of the GNU Affero  
General Public License into a single combined  
work, and to convey the resulting work.  
The terms of this License will continue to  
apply to the part which is the covered work,  
but the special requirements of the GNU  
Affero General Public License, section 13,  
concerning interaction through a network will  
apply to the combination as such.  
A patent license is “discriminatory” if it does  
not include within the scope of its coverage,  
prohibits the exercise of, or is conditioned  
on the non-exercise of one or more of the  
rights that are specifically granted under this  
License. You may not convey a covered work  
if you are a party to an arrangement with a  
third party that is in the business of distributing  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14. Revised Versions of this License.  
16. Limitation of Liability.  
The Free Software Foundation may publish  
revised and/or new versions of the GNU  
General Public License from time to time.  
Such new versions will be similar in spirit to  
the present version, but may differ in detail to  
address new problems or concerns.  
IN NO EVENT UNLESS REQUIRED BY  
APPLICABLE LAW OR AGREED TO IN  
WRITING WILL ANY COPYRIGHT HOLDER,  
OR ANY OTHER PARTY WHO MODIFIES  
AND/OR CONVEYS THE PROGRAM  
AS PERMITTED ABOVE, BE LIABLE TO  
YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES ARISING OUT  
OF THE USE OR INABILITY TO USE THE  
PROGRAM (INCLUDING BUT NOT LIMITED  
TO LOSS OF DATA OR DATA BEING  
RENDERED INACCURATE OR LOSSES  
SUSTAINED BY YOU OR THIRD PARTIES  
OR A FAILURE OF THE PROGRAM TO  
OPERATE WITH ANY OTHER PROGRAMS),  
EVEN IF SUCH HOLDER OR OTHER PARTY  
HAS BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
Each version is given a distinguishing version  
number. If the Program specifies that a certain  
numbered version of the GNU General Public  
License “or any later version” applies to it, you  
have the option of following the terms and  
conditions either of that numbered version  
or of any later version published by the Free  
Software Foundation. If the Program does  
not specify a version number of the GNU  
General Public License, you may choose any  
version ever published by the Free Software  
Foundation.  
If the Program specifies that a proxy can  
decide which future versions of the GNU  
General Public License can be used, that  
proxy's public statement of acceptance of a  
version permanently authorizes you to choose  
that version for the Program.  
17. Interpretation of Sections 15 and 16.  
If the disclaimer of warranty and limitation of  
liability provided above cannot be given local  
legal effect according to their terms, reviewing  
courts shall apply local law that most closely  
approximates an absolute waiver of all civil  
liability in connection with the Program, unless a  
warranty or assumption of liability accompanies  
a copy of the Program in return for a fee.  
Later license versions may give you additional  
or different permissions. However, no  
additional obligations are imposed on any  
author or copyright holder as a result of your  
choosing to follow a later version.  
END OF TERMS AND CONDITIONS  
15. Disclaimer of Warranty.  
GNU LESSER GENERAL PUBLIC  
LICENSE  
THERE IS NO WARRANTY FOR THE  
PROGRAM, TO THE EXTENT PERMITTED  
BY APPLICABLE LAW. EXCEPT WHEN  
OTHERWISE STATED IN WRITING THE  
COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE PROGRAM  
Version 2.1, February 1999  
Copyright (C)1991, 1999 Free Software  
Foundation, Inc.  
“AS IS” WITHOUT WARRANTY OF  
51 Franklin Street, Fifth Floor, Boston,  
MA 02110-1301 USA  
ANY KIND, EITHER EXPRESSED OR  
IMPLIED, INCLUDING, BUT NOT LIMITED  
TO, THE IMPLIED WARRANTIES OF  
Everyone is permitted to copy and  
MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE. THE ENTIRE RISK  
AS TO THE QUALITY AND PERFORMANCE  
OF THE PROGRAM IS WITH YOU. SHOULD  
THE PROGRAM PROVE DEFECTIVE, YOU  
ASSUME THE COST OF ALL NECESSARY  
SERVICING, REPAIR OR CORRECTION.  
distribute verbatim copies of this license  
document, but changing it is not allowed.  
[This is the first released version of the  
Lesser GPL. It also counts as the successor  
of the GNU Library Public License, version  
2, hence the version number 2.1.]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
We protect your rights with a two-step  
method : (1)we copyright the library, and  
(2)we offer you this license, which gives you  
legal permission to copy, distribute and/or  
modify the library.  
Preamble  
The licenses for most software are designed  
to take away your freedom to share and  
change it. By contrast, the GNU General  
Public Licenses are intended to guarantee  
your freedom to share and change free  
software--to make sure the software is free  
for all its users.  
To protect each distributor, we want to  
make it very clear that there is no warranty  
for the free library. Also, if the library is  
modified by someone else and passed  
on, the recipients should know that what  
they have is not the original version,so  
that the original author's reputation will  
not be affected by problems that might be  
introduced by others.  
This license, the Lesser General Public  
License, applies to some specially  
designated software packages--typically  
libraries--of the Free Software Foundation  
and other authors who decide to use it.You  
can use it too, but we suggest you first  
think carefully about whether this license or  
the ordinary General Public License is the  
better strategy to use in any particular case,  
based on the explanations below.  
Finally, software patents pose a constant  
threat to the existence of any free program.  
We wish to make sure that a company  
cannot effectively restrict the users of a free  
program by obtaining a restrictive license  
from a patent holder.  
When we speak of free software, we are  
referring to freedom of use, not price.  
Our General Public Licenses are designed  
to make sure that you have the freedom  
to distribute copies of free software (and  
charge for this service if you wish) ; that  
you receive source code or can get it if you  
want it ; that you can change the software  
and use pieces of it in new free programs ;  
and that you are informed that you can do  
these things.  
Therefore, we insist that any patent license  
obtained for a version of the library must  
be consistent with the full freedom of use  
specified in this license.  
Most GNU software, including some  
libraries, is covered by the ordinary GNU  
General Public License. This license, the  
GNU Lesser General Public License,  
applies to certain designated libraries, and  
is quite different from the ordinary General  
Public License. We use this license for  
certain libraries in order to permit linking  
those libraries into non-free programs.  
To protect your rights, we need to make  
restrictions that forbid distributors to deny  
you these rights or to ask you to surrender  
these rights. These restrictions translate to  
certain responsibilities for you if you distribute  
copies of the library or if you modify it.  
When a program is linked with a library,  
whether statically or using a shared library,  
the combination of the two is legally  
speaking a combined work, a derivative of  
the original library. The ordinary General  
Public License therefore permits such  
linking only if the entire combination fits its  
criteria of freedom.  
For example, if you distribute copies of the  
library, whether gratis or for a fee, you must  
give the recipients all the rights that we  
gave you. You must make sure that they,  
too, receive or can get the source code.  
If you link other code with the library, you  
must provide complete object files to the  
recipients, so that they can relink them with  
the library after making changes to the library  
and recompiling it. And you must show them  
these terms so they know their rights.  
The Lesser General Public License permits  
more lax criteria for linking other code with  
the library.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
We call this license the "Lesser" General  
Public License because it does Less  
to protect the user's freedom than the  
ordinary General Public License. It also  
provides other free software developers  
Less of an advantage over competing non-  
free programs.  
TERMS AND CONDITIONS FOR  
COPYING, DISTRIBUTION AND  
MODIFICATION  
0. This License Agreement applies to any  
software library or other program which  
contains a notice placed by the copyright  
holder or other authorized party saying  
it may be distributed under the terms of  
this Lesser General Public License (also  
called "this License"). Each licensee is  
addressed as "you".  
These disadvantages are the reason we  
use the ordinary General Public License for  
many libraries. However, the Lesser license  
provides advantages in certain special  
circumstances.  
A "library" means a collection of software  
functions and/or data prepared so as to  
be conveniently linked with application  
programs (which use some of those  
functions and data)to form executables.  
For example, on rare occasions, there may  
be a special need to encourage the widest  
possible use of a certain library, so that it  
becomes a de-facto standard. To achieve  
this, non-free programs must be allowed to  
use the library. A more frequent case is that  
a free library does the same job as widely  
used non-free libraries. In this case, there  
is little to gain by limiting the free library to  
free software only, so we use the Lesser  
General Public License.  
The "Library", below, refers to any such  
software library or work which has been  
distributed under these terms. A "work  
based on the Library" means either the  
Library or any derivative work under  
copyright law : that is to say, a work  
containing the Library or a portion of  
it,either verbatim or with modifications  
and/or translated straightforwardly into  
another language. (Hereinafter, translation  
is included without limitation in the term  
"modification".)  
In other cases,permission to use a  
particular library in non-free programs  
enables a greater number of people to use  
a large body of free software. For example,  
permission to use the GNU C Library in  
non-free programs enables many more  
people to use the whole GNU operating  
system, as well as its variant, the GNU/  
Linux operating system.  
"Source code" for a work means the  
preferred form of the work for making  
modifications to it.  
Although the Lesser General Public License  
is Less protective of the users' freedom, it  
does ensure that the user of a program that  
is linked with the Library has the freedom  
and the wherewithal to run that program  
using a modified version of the Library.  
For a library, complete source code  
means all the source code for all modules  
it contains, plus any associated interface  
definition files, plus the scripts used to  
control compilation and installation of the  
library.  
The precise terms and conditions for  
copying, distribution and modification  
follow. Pay close attention to the difference  
between a "work based on the library" and  
a "work that uses the library". The former  
contains code derived from the library,  
whereas the latter must be combined with  
the library in order to run.  
Activities other than copying, distribution  
and modification are not covered by this  
License ; they are outside its scope. The act  
of running a program using the Library is not  
restricted, and output from such a program  
is covered only if its contents constitute a  
work based on the Library (independent of  
the use of the Library in a tool for writing it).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Whether that is true depends on what the  
Library does and what the program that  
uses the Library does.  
(For example, a function in a library to  
compute square roots has a purpose  
that is entirely well-defined independent  
of the application. Therefore,Subsection  
2d requires that any application-supplied  
function or table used by this function must  
be optional : if the application does not  
supply it, the square root function must still  
compute square roots.)  
1. You may copy and distribute verbatim  
copies of the Library's complete source  
code as you receive it, in any medium,  
provided that you conspicuously and  
appropriately publish on each copy  
an appropriate copyright notice and  
disclaimer of warranty ; keep intact all  
the notices that refer to this License and  
to the absence of any warranty ; and  
distribute a copy of this License along  
with the Library.  
These requirements apply to the modified  
work as a whole. If identifiable sections of that  
work are not derived from the Library, and  
can be reasonably considered independent  
and separate works in themselves, then this  
License, and its terms, do not apply to those  
sections when you distribute them as separate  
works. But when you distribute the same  
sections as part of a whole which is a work  
based on the Library, the distribution of the  
whole must be on the terms of this License,  
whose permissions for other licensees extend  
to the entire whole, and thus to each and  
every part regardless of who wrote it. Thus, it  
is not the intent of this section to claim rights  
or contest your rights to work written entirely  
by you ; rather, the intent is to exercise the  
right to control the distribution of derivative or  
collective works based on the Library.  
You may charge a fee for the physical act  
of transferring a copy, and you may at  
your option offer warranty protection in  
exchange for a fee.  
2. You may modify your copy or copies  
of the Library or any portion of it, thus  
forming a work based on the Library, and  
copy and distribute such modifications  
or work under the terms of Section 1  
above, provided that you also meet all of  
these conditions :  
a)The modified work must itself be a  
software library.  
b)You must cause the files modified to  
In addition, mere aggregation of another  
work not based on the Library with the  
Library (or with a work based on the  
Library)on a volume of a storage or  
carry prominent notices stating that  
you changed the files and the date of  
any change.  
distribution medium does not bring the  
other work under the scope of this License.  
c)You must cause the whole of the work  
to be licensed at no charge to all third  
parties under the terms of this License.  
3. You may opt to apply the terms of the  
ordinary GNU General Public License  
instead of this License to a given  
d)If a facility in the modified Library refers  
to a function or a table of data to be  
supplied by an application program  
that uses the facility, other than as  
an argument passed when the facility  
is invoked, then you must make a  
good faith effort to ensure that, in the  
event an application does not supply  
such function or table, the facility still  
operates, and performs whatever part  
of its purpose remains meaningful.  
copy of the Library. To do this, you  
must alter all the notices that refer to  
this License, so that they refer to the  
ordinary GNU General Public License,  
version 2, instead of to this License. (If  
a newer version than version 2 of the  
ordinary GNU General Public License  
has appeared, then you can specify that  
version instead if you wish.) Do not make  
any other change in these notices.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Once this change is made in a given copy,  
it isirreversible for that copy, so the ordinary  
GNU General Public License applies to all  
subsequent copies and derivative works  
made from that copy.  
Library, the object code for the work may  
be a derivative work of the Library even  
though the source code is not. Whether  
this is true is especially significant if the  
work can be linked without the Library, or if  
the work is itself a library.  
This option is useful when you wish to  
copy part of the code of the Library into a  
program that is not a library.  
The threshold for this to be true is not  
precisely defined by law.  
4. You may copy and distribute the Library  
(or a portion or derivative of it, under  
Section 2) in object code or executable  
form under the terms of Sections 1 and  
2 above provided that you accompany  
it with the complete corresponding  
machine-readable source code,  
which must be distributed under the  
terms of Sections 1 and 2 above on a  
medium customarily used for software  
interchange.  
If such an object file uses only numerical  
parameters, data structure layouts  
and accessors, and small macros and  
small inline functions (ten lines or less in  
length), then the use of the object file is  
unrestricted, regardless of whether it is  
legally a derivative work. (Executables  
containing this object code plus portions  
of the Library will still fall under Section 6.)  
Otherwise, if the work is a derivative of the  
Library, you may distribute the object code  
for the work under the terms of Section.  
If distribution of object code is made by  
offering access to copy from a designated  
place, then offering equivalent access to  
copy the source code from the same place  
satisfies the requirement to distribute the  
source code, even though third parties are  
not compelled to copy the source along  
with the object code.  
Any executables containing that work also  
fall under Section 6, whether or not they are  
linked directly with the Library itself.  
6. As an exception to the Sections above,  
you may also combine or link a "work  
that uses the Library" with the Library  
to produce a work containing portions  
of the Library, and distribute that work  
under terms of your choice,provided  
that the terms permit modification of the  
work for the customer's own use and  
reverse engineering for debugging such  
modifications.  
5. A program that contains no derivative  
of any portion of the Library, but is  
designed to work with the Library by  
being compiled or linked with it, is called  
a "work that uses the Library". Such a  
work, in isolation, is not a derivative work  
of the Library, and therefore falls outside  
the scope of this License.  
You must give prominent notice with each  
copy of the work that the Library is used  
in it and that the Library and its use are  
covered by this License. You must supply  
a copy of this License. If the work during  
execution displays copyright notices, you  
must include the copyright notice for the  
Library among them, as well as a reference  
directing the user to the copy of this  
License. Also, you must do one of these  
things :  
However, linking a "work that uses the  
Library" with the Library creates an  
executable that is a derivative of the Library  
(because it contains portions of the Library),  
rather than a "work that uses the library".  
The executable is therefore covered by this  
License.  
Section 6 states terms for distribution of  
such executables.  
a)Accompany the work with the  
When a "work that uses the Library" uses  
material from a header file that is part of the  
complete corresponding machine-  
Download from Www.Somanuals.com. All Manuals Search And Download.  
readable source code for the Library  
including whatever changes were used  
in the work (which must be distributed  
under Sections 1 and 2 above) ; and,  
if the work is an executable linked with  
the Library, with the complete machine-  
readable "work that uses the Library",  
as object code and/or source code,  
so that the user can modify the Library  
and then relink to produce a modified  
executable containing the modified  
Library. (It is understood that the user  
who changes the contents of definitions  
files in the Library will not necessarily  
be able to recompile the application to  
use the modified definitions.)  
from it. However, as a special exception,  
the materials to be distributed need not  
include anything that is normally distributed  
(in either source or binary form)with the  
major components (compiler, kernel, and  
so on) of the operating system on which the  
executable runs, unless that component itself  
accompanies the executable. It may happen  
that this requirement contradicts the license  
restrictions of other proprietary libraries that  
do not normally accompany the operating  
system. Such a contradiction means you  
cannot use both them and the Library  
together in an executable that you distribute.  
7. You may place library facilities that are  
a work based on the Library side-by-  
side in a single library together with  
other library facilities not covered by this  
License, and distribute such a combined  
library, provided that the separate  
distribution of the work based on the  
Library and of the other library facilities is  
otherwise permitted, and provided that  
you do these two things :  
b)Use a suitable shared library  
mechanism for linking with the Library.  
A suitable mechanism is one that  
(1)uses at run time a copy of the library  
already present on the user's computer  
system, rather than copying library  
functions into the executable, and  
(2)will operate properly with a modified  
version of the library, if the user installs  
one,as long as the modified version is  
interface-compatible with the version  
that the work was made with.  
a)Accompany the combined library with  
a copy of the same work based on the  
Library, uncombined with any other  
library facilities. This must be distributed  
under the terms of the Sections above.  
c)Accompany the work with a written  
offer, valid for at least three years,  
to give the same user the materials  
specified in Subsection 6a, above,  
for a charge no more than the cost  
ofperforming this distribution.  
b)Give prominent notice with the  
combined library of the fact that part  
of it is a work based on the Library,  
and explaining where to find the  
accompanying uncombined form of the  
same work.  
d)If distribution of the work is made  
by offering access to copy from a  
designated place, offer equivalent  
access to copy the above specified  
materials from the same place.  
8. You may not copy, modify, sublicense,  
link with, or distribute the Library except  
as expressly provided under this License.  
Any attempt otherwise to copy, modify,  
sublicense, link with, or distribute the  
Library is void, and will automatically  
terminate your rights under this License.  
However, parties who have received  
copies, or rights, from you under this  
License will not have their licenses  
terminated so long as such parties  
remain in full compliance.  
e)Verify that the user has already received  
a copy of these materials or that you  
have already sent this user a copy.  
For an executable, the required form of  
the "work that uses the Library" must  
include any data and utility programs  
needed for reproducing the executable  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. You are not required to accept this  
License, since you have not signed it.  
However, nothing else grants you  
is intended to apply, and the section  
as a whole is intended to apply in other  
circumstances.  
permission to modify or distribute the  
Library or its derivative works.  
It is not the purpose of this section to  
induce you to infringe any patents or other  
property right claims or to contest validity of  
any such claims ; this section has the sole  
purpose of protecting the integrity of the  
free software distribution system which is  
implemented by public license practices.  
These actions are prohibited by law if you  
do not accept this License. Therefore,  
by modifying or distributing the Library  
(or any work based on the Library), you  
indicate your acceptance of this License  
to do so, and all its terms and conditions  
for copying, distributing or modifying the  
Library or works based on it.  
Many people have made generous  
contributions to the wide range of software  
distributed through that system in reliance  
on consistent application of that system;it  
is up to the author/donor to decide if he or  
she is willing to distribute software through  
any other system and a licensee cannot  
impose that choice.  
10.Each time you redistribute the Library  
(or any work based on the Library), the  
recipient automatically receives a license  
from the original licensor to copy,  
distribute, link with or modify the Library  
subject to these terms and conditions.  
You may not impose any further  
restrictions on the recipients’ exercise  
of the rights granted herein.You are not  
responsible for enforcing compliance by  
third parties with this License.  
This section is intended to make thoroughly  
clear what is believed to be a consequence  
of the rest of this License.  
12.If the distribution and/or use of the  
Library is restricted in certain countries  
either by patents or by copyrighted  
interfaces, the original copyright  
holder who places the Library under  
this License may add an explicit  
geographical distribution limitation  
excluding those countries, so that  
distribution is permitted only in or  
among countries not thus excluded.In  
such case, this License incorporates the  
limitation as if written in the body of this  
License.  
11.If,as a consequence of a court judgment  
or allegation of patent infringement or for  
any other reason (not limited to patent  
issues), conditions are imposed on you  
(whether by court order, agreement or  
otherwise)that contradict the conditions  
of this License, they do not excuse you  
from the conditions of this License. If  
you cannot distribute so as to satisfy  
simultaneously your obligations under  
this License and any other pertinent  
obligations, then as a consequence you  
may not distribute the Library at all.  
For example, if a patent license would  
not permit royalty-free redistribution  
of the Library by all those who receive  
copies directly or indirectly through you,  
then the only way you could satisfy both  
it and this License would be to refrain  
entirely from distribution of the Library.  
13.The Free Software Foundation may  
publish revised and/or new versions of  
the Lesser General Public License from  
time to time. Such new versions will be  
similar in spirit to the present version,  
but may differ in detail to address new  
problems or concerns.  
Each version is given a distinguishing  
version number. If the Library specifies  
a version number of this License which  
applies to it and "any later version", you  
have the option of following the terms and  
If any portion of this section is held invalid  
or unenforceable under any particular  
circumstance, the balance of the section  
Download from Www.Somanuals.com. All Manuals Search And Download.  
conditions either of that version or of any  
later version published by the Free Software  
Foundation. If the Library does not specify  
a license version number, you may choose  
any version ever published by the Free  
Software Foundation.  
YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES ARISING  
OUT OF THE USE OR INABILITY TO  
USE THE LIBRARY (INCLUDING BUT  
NOT LIMITED TO LOSS OF DATA OR  
DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR  
THIRD PARTIES OR A FAILURE OF  
THE LIBRARY TO OPERATE WITH ANY  
OTHER SOFTWARE), EVEN IF SUCH  
HOLDER OR OTHER PARTY HAS  
BEEN ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGES.  
14.If you wish to incorporate parts of the  
Library into other free programs whose  
distribution conditions are incompatible  
with these, write to the author to ask  
for permission. For software which  
is copyrighted by the Free Software  
Foundation, write to the Free Software  
Foundation ; we sometimes make  
exceptions for this. Our decision will be  
guided by the two goals of preserving  
the free status of all derivatives of our  
free software and of promoting the  
sharing and reuse of software generally.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your  
New Libraries  
If you develop a new library, and you want  
it to be of the greatest possible use to  
the public, we recommend making it free  
software that everyone can redistribute  
and change. You can do so by permitting  
redistribution under these terms (or,  
alternatively, under the terms of the ordinary  
General Public License).  
NO WARRANTY  
15.BECAUSE THE LIBRARY IS LICENSED  
FREE OF CHARGE, THERE IS NO  
WARRANTY FOR THE LIBRARY,  
TO THE EXTENT PERMITTED BY  
APPLICABLE LAW. EXCEPT WHEN  
OTHERWISE STATED IN WRITING  
THE COPYRIGHT HOLDERS AND/  
OR OTHER PARTIES PROVIDE THE  
LIBRARY "ASIS" WITHOUT WARRANTY  
OF ANYKIND, EITHER EXPRESSED  
OR IMPLIED, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES  
OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE.THE  
ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE LIBRARY IS  
WITH YOU. SHOULD THE LIBRARY  
PROVE DEFECTIVE, YOU ASSUME THE  
COST OF ALL NECESSARY SERVICING,  
REPAIR OR CORRECTION.  
To apply these terms, attach the following  
notices to the library. It is safest to attach  
them to the start of each source file to most  
effectively convey the exclusion of warranty  
; and each file should have at least the  
"copyright" line and a pointer to where the  
full notice is found.  
One line to give the library's name and an  
idea of what it does.  
Copyright (C)year name of author  
This library is free software ; you can  
redistribute it and/or modify it under the  
terms of the GNU Lesser General Public  
License as published by the Free Software  
Foundation ; either version 2.1 of the  
License, or (at your option)any later version.  
16.IN NO EVENT UNLESS REQUIRED BY  
APPLICABLE LAW OR AGREED TO  
IN WRITING WILL ANY COPYRIGHT  
HOLDER, OR ANY OTHER PARTY  
WHO MAY MODIFY AND/OR  
REDISTRIBUTE THE LIBRARY AS  
PERMITTED ABOVE, BE LIABLE TO  
This library is distributed in the hope  
that it will be useful, but WITHOUT ANY  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY ; without even the implied  
warranty of MERCHANTABILITY or  
FITNESS FOR A PARTICULAR PURPOSE.  
See the GNU Lesser General Public  
License for more details.  
display the following acknowledgment :  
"This product includes software  
developed by the OpenSSL Project for  
use in the OpenSSLToolkit. (http://www.  
openssl.org/)"  
4. The names "OpenSSL Toolkit" and  
"OpenSSL Project" must not be used to  
endorse or promote products derived  
from this software without prior written  
permission. For written permission, please  
contact [email protected].  
You should have received a copy of the  
GNU Lesser General Public License along  
with this library ; if not, write to the Free  
Software Foundation, Inc.,51 Franklin Street,  
Fifth Floor, Boston, MA 02110-1301 USA  
Also add information on how to contact you  
by electronic and paper mail.  
5. Products derived from this software  
may not be called "OpenSSL" nor  
may "OpenSSL" appear in their names  
without prior written permission of the  
OpenSSL Project.  
You should also get your employer (if you  
work as a programmer)or your school, if  
any, to sign a "copyright disclaimer" for the  
library,if necessary. Here is a sample ; alter  
the names:  
6. Redistributions of any form whatsoever  
must retain the following acknowledgment:  
"This product includes software developed  
by the OpenSSL Project for use in the  
OpenSSL Toolkit (http://www.openssl.  
org/)"  
Yoyodyne, Inc., hereby disclaims all  
copyright interest in the library `Frob'(a  
library for tweaking knobs)written  
by James Random Hacker.  
signature of Ty Coon, 1 April 1990  
Ty Coon, President of Vice  
THIS SOFTWARE IS PROVIDED BY  
THE OpenSSL PROJECT “AS IS  
” AND ANY EXPRESSED OR IMPLIED  
WARRANTIES, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR  
PURPOSE ARE DISCLAIMED. IN  
NO EVENT SHALL THE OpenSSL  
PROJECT OR ITS CONTRIBUTORS BE  
LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS  
OR SERVICES ; LOSS OF USE,DATA,OR  
PROFITS ; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR  
TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT  
OF THE USE OF THIS SOFTWARE, EVEN  
IF ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGE.  
OpenSSL LICENSE  
Copyright (c)1998-2006 The OpenSSL  
Project. All rights reserved.  
Redistribution and use in source and  
binary forms, with or without modification,  
are permitted provided that the following  
conditions are met :  
1. Redistributions of source code must  
retain the above copyright notice, this  
list of conditions and the following  
disclaimer.  
2. Redistributions in binary form must  
reproduce the above copyright notice,  
this list of conditions and the following  
disclaimer in the documentation  
and/or other materials provided with the  
distribution.  
3. All advertising materials mentioning  
features or use of this software must  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This product includes cryptographic  
software written by Eric Young (eay@  
cryptsoft.com).  
and/or other materials provided with the  
distribution.  
3. All advertising materials mentioning  
features or use of this software must  
display the following acknowledgement :  
"This product includes cryptographic  
software written by Eric Young (eay@  
cryptsoft.com)" The word 'cryptographic'  
can be left out if the rouines from the  
library being used are not cryptographic  
related :-).  
This product includes software written by  
Tim Hudson ([email protected]).  
Original SSLeay License  
Copyright (C)1995-1998 Eric Young  
([email protected]) All rights reserved.  
This package is an SSL implementation  
writtenby Eric Young ([email protected]).  
The implementation was written so as to  
conform with Netscapes SSL.  
4. If you include any Windows specific code  
(or a derivative thereof)from the apps  
directory (application code) you must  
include an acknowledgement :  
"This product includes software written  
by Tim Hudson ([email protected])"  
This library is free for commercial and  
noncommercial use as long as the following  
conditions are aheared to. The following  
conditions apply to all code found in this  
distribution, be it the RC4, RSA, lhash,  
DES, etc.,code ; not just the SSL code.  
THIS SOFTWARE IS PROVIDED  
BY ERIC YOUNG “AS IS” AND ANY  
EXPRESS OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO,  
THE IMPLIED WARRANTIES OF  
The SSL documentation included with  
this distribution is covered by the same  
copyright terms except that the holder is  
Tim Hudson ([email protected]).  
MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL  
THE AUTHOR OR CONTRIBUTORS BE  
LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES  
(INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS  
OR SERVICES ; LOSS OF USE, DATA, OR  
PROFITS ; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR  
TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE)ARISING IN ANY WAY OUT  
OF THE USE OF THIS SOFTWARE, EVEN  
IF ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGE.  
Copyright remains Eric Young's, and as  
such any Copyright notices in the code are  
not to be removed.  
If this package is used in a product,Eric  
Young should be given attribution as the  
author of the parts of the library used.  
This can be in the form of a textual  
message at program startup or in  
documentation (online or textual) provided  
with the package.  
Redistribution and use in source and  
binary forms, with or without modification,  
are permitted provided that the following  
conditions are met :  
1. Redistributions of source code must  
retain the copyright notice, this list of  
conditions and the following disclaimer.  
The licence and distribution terms for any  
publically available version or derivative of  
this code cannot be changed.i.e.this code  
cannot simply be copied and put under  
another distribution licence [including the  
GNU Public Licence.]  
2. Redistributions in binary form must  
reproduce the above copyright notice,  
this list of conditions and the following  
disclaimer in the documentation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(Waste Electrical & Electronic Equipment)  
Correct Disposal of This Product  
(Applicable in the European Union and other European countries with separate collection systems)  
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger,  
headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent  
possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other  
types of waste and recycle them responsibly to promote the sustainable reuse of material resources.  
Household users should contact either the retailer where they purchased this product, or their local government office, for  
details of where and how they can take these items for environmentally safe recycling.  
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and  
its electronic accessories should not be mixed with other commercial wastes for disposal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Raritan Computer Switch Paragon switch User Guide
Raypak Heat Pump 6300tiPD User Guide
Rotel Stereo Receiver RSX 965 User Guide
Samsung All in One Printer 4200 User Guide
Samsung Blu ray Player BDH5900 User Guide
Samsung Computer Monitor 152X 172X User Guide
Samsung Printer SCX 5315F, SCX 5115 User Guide
Sanyo MP3 Player Accessories VCA 35E User Guide
Saturn Automobile 2007 Sky User Guide
Schumacher Battery Charger 9500A User Guide