Samsung Security Camera SCC C6403 User Guide

SmartDome Camera  
SCC-C6403  
E
F
Owner’s Instructions  
Manuel d’instruction  
Manual del usuario  
Es  
J
Part : AB68-00570A(00)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal  
things) or containers filled with water on top of the camera. (Doing so may  
cause personal injury due to fire, electrical shock, or falling objects.)  
FCC STATEMENT  
This device complies with Part 15 of the FCC Rules. Operation is subject to  
the following two conditions:  
7. Do not install the unit in humid, dusty, or sooty locations.  
(Doing so may cause fire or electrical shock.)  
8. If any unusual smells or smoke come from the unit, stop using the product.  
In such case, immediately disconnect the power source and contact the  
service center. (Continued use in such a condition may cause fire or  
electrical shock.)  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference  
that may cause undesired operation.  
9. If this product fails to operate normally, contact the store of purchase or  
your nearest service center. Never disassemble or modify this product in  
any way. (SAMSUNG is not liable for problems caused by unauthorized  
modifications or attempted repair.)  
Note: This equipment has been tested and found to comply with the limits for  
a Class A digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio  
10. When cleaning, do not spray water directly onto parts of the product.  
(Doing so may cause fire or electrical shock.)  
Wipe the surface with a dry cloth. Never use detergents or chemical  
cleaners on the product, as this may result in discoloration of surface or  
cause damage to the finish.  
communications. Operation of this equipment in a residential area is  
likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
Caution  
1. Do not drop objects on the product or apply strong shock to it. Keep away  
from a location subject to excessive vibration or magnetic interference.  
2. Do not install in a location subject to high temperature (over 122°F), low  
temperature (below 14°F), or high humidity.  
(Doing so may cause fire or electrical shock.)  
3. Avoid a location which is exposed to direct sunlight, or near heat sources  
such as heaters or radiators.  
(Neglecting to do so may result in a risk of fire.)  
4. If you want to relocate the already installed product, be sure to turn off the  
power and then move or reinstall it.  
5. Install in a well-ventilated location.  
6. Remove the power plug from the outlet when there is a lightning storm.  
(Neglecting to do so may cause fire or damage to the product.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of contents  
Before Usage  
Before Usage...............................................................................................................1-1  
This is a basic instruction manual for the SCC-C6403 user.  
It contains all the instructions needed to use the SCC-C6403 from  
a simple introduction of the control locations and functions of the  
SCC-C6403 to installation methods in the set up menu.  
Chapter 1 SCC-C6403 Overview..............................................................................1-4  
SCC-C6403 Introduction .............................................................................1-5  
Locations of Control.................................................................................1-6  
ADAPTER CONNECTION ..........................................................................1-8  
INITIAL SETTING........................................................................................1-9  
Setting RS-422A/RS-485 termination........................................................1-10  
E
We recommend all users of the SCC-C6403 from the advanced  
user who has used similar cameras before to the general user to  
read the instruction manual before using.  
Chapter 2 SCC-C6403 Installation...........................................................................2-1  
Before Installing...........................................................................................2-2  
Preparing the Cables...................................................................................2-3  
Cable Connection........................................................................................2-4  
Installing SCC-C6403..................................................................................2-5  
Installing the Camera ..................................................................................2-8  
The most frequently used feature in the SCC-C6403 would be the  
SCC-C6403 Setup Menu.  
The SCC-C6403 Setup Menu is explained in detailed in "Chapter  
3 Setup Menu Overview".  
Chapter 3 Setup Menu Overview .............................................................................3-1  
Structure of the Setup Menu........................................................................3-2  
1. CAMERA SET MENU .............................................................................3-4  
- CAMERA ID .........................................................................................3-4  
- V-SYNC................................................................................................3-5  
- COLOR/BW..........................................................................................3-6  
- MOTION DET.......................................................................................3-7  
- ZOOM SPEED .....................................................................................3-8  
- DIGITAL ZOOM ...................................................................................3-9  
- DISPLAY ZOOM ..................................................................................3-9  
- DISPLAY P/T .......................................................................................3-9  
- EXIT ...................................................................................................3-10  
2. VIDEO SET MENU ...............................................................................3-10  
- IRIS....................................................................................................3-10  
- ALC.................................................................................................3-10  
- BLC...............................................................................................3-10  
- MANU .............................................................................................3-11  
- SHUTTER..........................................................................................3-12  
- FLICKERLESS ................................................................................3-12  
- AGC ...................................................................................................3-13  
- MOTION.............................................................................................3-13  
- WHITE BAL........................................................................................3-14  
- DIS.....................................................................................................3-15  
- FOCUS MODE...................................................................................3-16  
- SPECIAL............................................................................................3-16  
- EXIT...................................................................................................3-17  
3. PRESET ................................................................................................3-17  
- POSITION SET .................................................................................3-18  
- PRESET ID........................................................................................3-18  
- VIDEO SET........................................................................................3-18  
- PRESET SPEED ...............................................................................3-18  
- DWELL TIME.....................................................................................3-18  
- IMAGE HOLD ....................................................................................3-18  
- EXIT...................................................................................................3-18  
The instructional manual is best used when read from beginning  
to end, but for users wanting to read only the part they need here  
are the Chapter summaries.  
"Chapter 1 SCC-C6403 Overview" includes a brief introduction  
of the SCC-C6403, part names and functions, and Switch  
Settings.  
"Chapter 2 SCC-C6403 Installation" explains the installation  
procedures of the SCC-C6403 and provides preparation and  
installation environment requirements.  
"Chapter 3 Setup Menu Overview" presents the structure of the  
Setup menu for the SCC-C6403 including a detailed explanation  
of the functions performed in each submenu.  
"Appendix SCC-C6403 Product Specifications" contains  
product specifications of the SCC-C6403 in itemized categories.  
1-1  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. ZONE SET...............................................................................................3-19  
- ZONE DIR SET....................................................................................3-19  
- ZONE AREA SET................................................................................3-20  
- LOCATION .......................................................................................3-21  
- ZONE ID SET ...................................................................................3-21  
- ZONE ENABLE.................................................................................3-21  
5. AUTO SET...............................................................................................3-22  
- AUTO PAN ..........................................................................................3-22  
- POSITION SET.................................................................................3-22  
- SPEED..............................................................................................3-23  
- DWELL TIME....................................................................................3-23  
- PATTERN............................................................................................3-23  
- SCAN...................................................................................................3-24  
- AUTO PLAY.........................................................................................3-25  
- AUTO RETURN................................................................................3-25  
- AUTO PLAY......................................................................................3-25  
- PLAY NUMBER................................................................................3-25  
6. ALARM SET ............................................................................................3-26  
- ALARM PRIORITY SET ......................................................................3-26  
- ALARM IN SET....................................................................................3-26  
- ALARM OUT SET................................................................................3-26  
- AUTO SET...........................................................................................3-27  
- AUX OUT CONTROL ..........................................................................3-27  
7. OTHER SET............................................................................................3-27  
- PROPORTINAL P/T ............................................................................3-27  
- TURBO P/T..........................................................................................3-28  
- AUTO CAL...........................................................................................3-28  
- AUTO FLIP ..........................................................................................3-28  
- CAM RESET........................................................................................3-28  
- LANGUAGE.........................................................................................3-28  
- PASSWORD........................................................................................3-28  
8. SYSTEM INFO ........................................................................................3-29  
9. Short Keys...............................................................................................3-30  
Chapter 1 SCC-C6403 Overview  
In this chapter we will briefly introduce the SCC-C6403 and  
show main functions, locations of control and Switch Setting.  
E
Product specifications ..........................................................................................3-32  
1-3  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SCC-C6403 Introduction  
Locations of Control  
FRONT  
SCC-C6403 is a zoom lens built in smart dome camera which  
provides you with the best monitoring function in connection with  
CCTV at banks or companies.  
E
The SCC-C6403 is a high quality surveillance camera using x32  
zoom lens and digital zoom IC, it can catch clear images up to 320  
times.  
SCC-C6403 has a variety of functions such as;  
- DAY/NIGHT to improve the sensitivity by automatic conversion  
into the black and white mode at night or in the environment with  
low illumination,  
- White Balance to control the brightness to the illumination,  
- Backlight Compensation under spotlight or utmost bright  
illumination,  
- Auto Focus to automatically adjust the focus to the subject  
movement,  
- PAN/TILT for an easy operation.  
The SCC-C6403 uses an Alarm function for alert situations and  
moving camera in the direction you want, ZOOM-IN and  
ZOOM-OUT functions can be remote controlled.  
1-5  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADAPTER CONNECTION  
BACK  
SCC-C6403 Adapter BOARD  
E
AC 24V  
OUT  
POWER  
AC 24V  
OUT  
POWER  
1-7  
1-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INITIAL SETTING  
Setting RS-422A/RS-485 termination  
CAMERA ADDRESS SETUP  
Use SW701, SW702, or SW703 for Camera Address setup. You may  
allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702  
the 2nd digit, and SW703 the 1st digit.  
1
2
EX) In case of Camera Address 1, see the following figure for setup.  
As it is shown in the structure map, when Controller and RS-422A/RS-  
485 is connected it should be terminated according to the Cable feature  
of impedance on the each end of the transmitting line to transfer the  
signals in long distance by controlling the reflection of the signals to the  
lowest.  
E
SW701  
SW702  
SW703  
Setting communication Protocol  
Use number 1~4 PIN of SW704 to set communication Protocol.  
Division  
n < 32  
PIN  
A : SAMSUNG HALF  
B : SAMSUNG FULL  
PIN1 PIN2 PIN3 PIN4  
OFF OFF OFF OFF  
Comp  
Termination  
SW1-ON  
A
B
C
D
E
F
G
H
I
ON  
OFF  
ON  
OFF OFF OFF  
ON  
ON  
OFF OFF  
OFF OFF  
SEE INSTRUCTION MANUAL  
ON 1 2 3 4 5 6 7 8  
SW704  
(x1)  
OFF OFF  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
(x100) (x10)  
ON  
OFF  
ON  
OFF  
ON  
<RS-485 Half Duplex Organization>  
SW701 SW702 SW703  
ON  
Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.  
OFF OFF OFF  
J
ON  
OFF  
ON  
OFF OFF  
ON  
K
L
ON  
ON  
OFF  
OFF  
ON  
ON  
n < 32  
ON  
M
N
O
P
OFF OFF  
ON  
Division  
SW1-ON  
ON  
OFF  
ON  
OFF  
ON  
ON  
ON  
ON  
ON  
SW2-ON  
(BOTTOM VIEW)  
Division  
ON  
ON  
ON  
Baud Rate Setting  
Use PIN 5 and 6 of SW704.  
1
2
3
4
5
6
7
8
<RS-422A/RS-485 Full Duplex Organization>  
ON  
OFF  
SW 704  
PIN 6  
ON  
A communication error may occur if you connect multiple cameras that are  
assigned the same address in the network.  
BAUD RATE  
4800 BPS  
PIN 5  
ON  
ON  
9600 BPS  
OFF  
ON  
OFF  
OFF  
19200 BPS  
38400 BPS  
OFF  
The factory default setting is set to 9600BPS.  
1-9  
1-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Installing  
Checking Package Contents  
Please check that all components listed below are included in the  
package:  
Chapter 2 SCC-C6403 Installation  
E
In this chapter, we will check the contents of the package before  
installing the SCC-C6403, and prepare a power adapter suitable for  
the power supply system.  
(Power Consumption: 18W; Voltage: AC24V, 1.5A)  
Then, we will install the SCC-C6403 and connect the cables.  
SCC-C6403  
Bracket anchor  
Owners  
Instructions  
AC 24V  
OUT  
POWER  
Screws  
Camera Holder  
Adapter Board  
Cover Body (Option)  
2-1  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cable Connection  
Preparing the Cables  
1. First, connect one end of the  
BNC video cable connector to  
the Video Output Terminal  
(VIDEO OUT)  
To install and use the SCC-C6403, the following cables should be  
prepared.  
Power Adapter Cable  
The cable that plugs into the SCC-C6403 power input receptacle has the  
rated voltage of AC24V, 1.5A.  
Check the rated voltage before using the cable.  
2. Then, connect the other end of  
the connector to the Video Input  
Terminal of the monitor.  
E
3. Now connect the Power Adapter  
Cable. Use a driver to screw  
one part of the two lines of  
Power Adapter to Power Input  
Terminal of the SCC-C6403.  
Video Cable  
The SCC-C6403's cable is a BNC Cable for connecting the video-output  
terminal to the video-input terminal of the monitor.  
4. Adjust the switch on the Power Adapter to the proper voltage.  
Then, connect the Power Adapter's plug to the Power Connector.  
5. Connect the Remote Control  
Terminal of the  
SCC-C6403  
and the external Controller.  
Controller  
Adapter BOARD  
2-3  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing SCC-C6403  
Installation Precautions  
3) INDOOR HOUSING (SHG-120)  
1) Make sure that the installation site can sufficiently support a minimum of  
four times the net weight of the SCC-C6403 SmartDome Camera and  
other accessories.  
This housing is used for installing the SmartDome Camera to an indoor  
wall or a ceiling.  
2) Install in an area where the space above the ceiling board is over 18 cm  
(7 in.) high.  
3) Use the supplied screws to fasten the camera to the bracket assembly.  
4) Keep persons away from the installation area, as there is a risk of falling  
objects.  
E
Also, move valuables to a safe location before installation.  
Separately Sold Products for Installation  
Depending on the installation site, it may be convenient to use one of the  
following products.  
1) CEILING MOUNT BRACKET  
(SBR-100DCM)  
4) OUTDOOR HOUSING (SHG-220)  
This bracket is used for installing  
the SmartDome CAMERA in the  
plenum above the drop ceiling.  
This housing is used for installing the SmartDome Camera to an  
outdoor wall or a ceiling.  
2) WALL MOUNT ADAPTOR  
(SADT-100WM)  
This adaptor is used for installing the  
indoor housing or the outdoor  
housing for the SmartDome Camera  
on a wall.  
To install and use OUTDOOR HOUSING, remove the Clear Case  
from the Camera body before installation.  
2-5  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Camera  
1. [Figure 1] Install the structure on the  
ceiling.  
(Refer to Installation reference  
for the Length of the structure)  
5) CEILING MOUNT ADAPTOR (SADT-100CM)  
This adaptor is used for installing the indoor housing or the outdoor  
housing for the SmartDome Camera to a concrete ceiling.  
* Built in by the builder of the structure  
E
[Figure 1]  
2. Make a hole in the ceiling where the camera will be installed.  
(The hole should be about  
ø185)  
3. [Figure 2] Assemble the  
BRKT-ANCHOR on the ceiling  
and screw the 4 bolts in.  
6) POLE MOUNT ADAPTOR (SADT-100PM)  
This adaptor is used for installing the WALL MOUNT ADAPTOR  
(SADT-100WM) to a pole that is over 8 cm (2.76 in.) in diameter.  
[Figure 2]  
4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER.  
(See page 2-4)  
[Figure 3]  
[Figure 4]  
2-7  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. [Figure 5] Match the  
6. Pull the safety wire from the case  
body, and assembly it to the camera  
holder.  
BRKT-ANCHOR and CAMERA  
ADAPTER and use 4screws  
(PH M4 x 8) to assemble them.  
Chapter 3 Setup Menu Overview  
[Figure 5]  
[Figure 6]  
In this chapter, we will look over the Setup Menu of the  
SCC-C6403, First we'll look over the overall structure of the  
Setup Menu, and then we'll look at the functions of each menu.  
E
[Figure 7]  
7. [Figure 7] Match the 3 holes on the  
back of the CAMERA and the  
CONNECTOR and turn it left about  
15 degrees.  
(Check the sound of LOCKING  
and that the LEVER-LOCKING  
is in place)  
* Use the screws (BH M3 x L8) to  
connect the CAMERA and the  
ADAPTER so they don't move.  
8. [Figure 8] Assemble the  
[Figure 8]  
COVER-BODY onto the DOME.  
2-9  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Structure of the Setup Menu  
ALARM SET  
ALARM PRIORITY SET  
ALARM IN SET  
ALARM1~4 1~4  
EXIT  
QUIT/SAVE  
CAMERA SET  
CAMERA ID  
V-SYNC  
ON.../OFF  
INT/LINE...  
ALARM1~4  
EXIT  
NO/NC/OFF  
QUIT/SAVE  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
DISPLAY ZOOM  
DISPLAY P/T  
EXIT  
COLOR.../BW.../AUTO...  
OFF/ON...  
1/2/3/4  
0FF/X2 ~ X10  
OFF/ON  
OFF/ON  
ALARM OUT SET  
ALARM1~4  
MOTION  
EXIT  
1~3  
1~3  
QUIT/SAVE  
E
QUIT/SAVE/PRESET  
AUTO SET  
ALARM1~4  
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4  
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4  
QUIT/SAVE  
MOTION  
EXIT  
VIDEO SET  
IRIS  
SHUTTER  
AGC/MOTION  
ALC.../MANU...  
OFF/1/100(1/120)~1/10K/AUTOX2...~X128...  
OFF/LOW/HIGH(AGC)  
S.SLOW/SLOW/NORM/FAST/F.FAST(MOTION)  
AUX OUT CONTROL  
OUT1 ON/OFF  
OUT2 ON/OFF  
OUT3 ON/OFF  
EXIT QUIT/SAVE  
WHITE BAL  
DIS  
FOCUS MODE  
SPECIAL  
ATW1/ATW2/AWC/MANU...  
ON/OFF  
ONEAF/MF  
...  
RET  
Y-LEVEL  
C-LEVEL  
DETAIL  
(0)l---  
(0)l---  
(0)l---  
OTHER SET  
PROPORTIONAL P/T  
TURBO P/T  
AUTO CAL  
AUTO FLIP  
CAM RESET  
LANGUAGE  
PASSWORD  
EXIT  
ON/OFF  
ON/OFF  
OFF/6H/12H/18H/24H  
ON/OFF  
RET  
EXIT  
QUIT/SAVE/PRESET  
...  
ENGLISH/FRANÇAIS/ESPAÑOL/JAPANESE  
ON.../OFF  
QUIT/SAVE  
PRESET  
POSITION SET  
PRESET ID  
VIDEO SET  
PRESET SPEED  
DWELL TIME  
IMAGE HOLD  
EXIT  
...  
ON.../OFF  
ON.../OFF  
1~8  
SYSTEM INFO  
1~60S  
ON/OFF  
QUIT/SAVE/DEL  
The diagram shown above illustrates the overall structure of the Setup Menu.  
In this section, a description of the Setup menu features will enable users of the  
SCC-C6403 to tailor it to their personal needs.  
ZONE SET  
AUTO SET  
ZONE DIR SET  
ZONE AREA SET  
EXIT  
OFF/ON...  
OFF/ON...  
QUIT/SAVE  
AUTO PAN  
PATTERN  
SCAN  
AUTO PLAY  
RET  
1.../2.../3.../4...  
1.../2.../3...  
1.../2.../3.../4...  
...  
3-2  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(CAMERA ID)  
(CAMERA SET)  
If the power is turned off after PRESET, AUTO PAN, SCAN,  
PATTERN function is activated and no other control is made, camera  
will do the same function after the power is turned on.  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
ON...  
INT  
A B C D E F G H I J K L  
M N O PQ R S T U V W X  
Y Z 0 1 2 3 4 5 6 7 8 9  
COLOR...  
OFF  
3
:
!
- +  
(
)
/
Press  
OFF  
SP ï î SP  
LOCATION...  
RET  
Use the controller to press the MENU selection key and the following  
screen will be displayed.  
[Enter]  
DISPLAY ZOOM OFF  
DISPLAY P/T  
OFF  
SCC-C6403........  
EXIT  
QUIT  
** MAIN MENU **  
CAMERA SET...  
" ... " Means there are Sub Menus.  
0
5
1
6
2
7
3
8
4
9
VIDEO SET...  
PRESET ...  
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
E
❈  
V-SYNC  
In the V-SYNC menu, vertical synchronization can be selected. The  
vertical synchronization signal supported by the SCC-C6403 is the INT  
mode made by clock inside the SCC-C6403 and LINE mode adjusting  
vertical synchronization to the exterior power frequency.  
PASSWORD  
DEFINED  
PASSWORD  
UNDEFINED  
Select LINE and press [Enter]. You will see the LINE LOCK submenu  
where you can adjust the phase of the LINE LOCK.  
You can use the PHASE menu of the LINE LOCK submenu to assign as  
much PHASE as you want.  
In case of , use UP/DOWN/LEFT/RIGHT/[ENTER] key for MENU  
setup. In case of , type in the 4 digit password first. If correct, the  
MENU selection screen like  
will be displayed and you will be able to  
set up MENU by pressing UP/DOWN/LEFT/RIGHT/[ENTER] key.  
(CAMERA SET)  
(LL-PHASE)  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
OFF  
LINE...  
COLOR...  
OFF  
1. CAMERA SET MENU  
3
OFF  
Press  
CAMERA ID  
[Enter]  
DISPLAY ZOOM OFF  
DISPLAY P/T  
OFF  
The CAMERA ID menu assigns an ID to the SCC-C6403 to be displayed on  
the connected monitor.On the CAMERA SET menu screen, select CAMERA  
ID to ON and press [Enter]. You will see the sub screen for deciding on the  
ID of the SCC-C6403. The Camera ID can have up to 20 alphanumeric  
characters, along with several special characters.  
PHASE  
RET  
(-262)I--------  
EXIT  
QUIT  
The assigned camera ID may be positioned to any desired location on the  
screen by using the LOCATION submenu.  
3-4  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COLOR/BW  
In AUTO mode, AGC will be displayed as ---. You cant adjust the  
settings manually.  
In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.  
In a poor illumination environment, the IR filter is turned off in the BW mode the its  
sensitivity increases as high as a black and white camera. On the other hand, the  
IR filter is turned on and the sensitivity decreases in the COLOR mode.  
(CAMERA SET)  
(AUTO)  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
OFF  
INT  
COLOR  
: The IR Filter is ON and the screen is normal. You can press the  
[Enter] key to set the COLOR GAIN LEVEL. And when the AGC  
function is on, you can set the AGC COLOER LEVEL.  
AUTO...  
OFF  
3
Press  
OFF  
BURST  
LEVEL  
DURATION  
RET  
ON  
LOW  
S --|---- L  
[Enter]  
DISPLAY ZOOM OFF  
DISPLAY P/T  
OFF  
(CAMERA SET)  
(COLOR)  
EXIT  
QUIT  
E
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION  
ZOOM SPEED  
DIGITAL ZOOM OFF  
DISPLAY ZOOM OFF  
DISPLAY P/T  
OFF  
INT  
COLOR …  
OFF  
3
Press  
Caution : If you use an infrared light source while in AUTO mode, AUTO  
[Enter]  
switching malfunction and camera AF malfunction may occur.  
GAIN  
AGC COLOR  
RET  
(0)I--------  
(0)----I----  
OFF  
EXIT  
QUIT  
MOTION DET  
BW  
: The IR Filter is OFF and the screen is black and white.  
In MOTION DET, you can set the Motion Detection function, Motion Detection  
Sensitivity, and the Area of Motion Detection. If the Motion Detection function  
is set, the movement of an intruder can be detected. When motion is detected,  
it sets off the Alarm signal of the Controller.  
(Sensitivity to low light is increased to a level comparable to a black  
and white camera.)  
Select BW and press [ENTER] and the additional menu to select  
BURST ON/OFF will appear.  
AUTO  
: Select to automatically switch between the COLOR mode and BW  
mode depending on the amount of light. In low light conditions, the  
IR Filter is turned OFF and the sensitivity to low light is increased  
by switching to the BW mode, but in bright light conditions, the IR  
Filter is turned ON and the sensitivity is decreased by switching to  
the COLOR mode.  
(CAMERA SET)  
(MOTION DET)  
CAMERA ID  
V-SYNC  
OFF  
INT  
COLOR...  
ON...  
3
OFF  
OFF  
OFF  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
DISPLAY ZOOM  
DISPLAY P/T  
Press  
[Enter]  
AREA  
USER...  
Select AUTO and press [ENTER] and the additional menu to select  
BW LEVEL and DURATION will appear.  
SENSITIVITY L ---|--- H  
RET  
EXIT  
QUIT  
- BURST ON : The color burst signal is output together with black and white  
composite video signal.  
- BURST OFF : The color burst signal is not output.  
- LEVEL  
: You can set the brightness level that changes from COLOR mode  
to BW mode in 3 steps : LOW, MEDIUM, and HIGH.  
- DURATION : Set the HOLDING time for switching between COLOR and BW  
mode depending the changes in the amount of light. You can set  
the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).  
3-6  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Select ON and press [Enter ] to display an additional menu window of  
MOTION DET .  
DIGITAL ZOOM  
You may set up the digital zoom magnification ratio in the DIGITAL ZOOM  
menu. The magnification ratio ranges from OFF to 10. If you set Digital  
Zoom of SCC-C6403 to max. 10 times, the mode will become the 32 time  
optical zoom and you will be able to enlarge a subject by max. 320 times.  
Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.  
You can select one from the sub items of TOP..., BOTTOM..., LEFT...,  
RIGHT..., CENTER... or USER... as AREA where the Motion Detection  
function is applied.Select one from TOP..., BOTTOM..., LEFT..., RIGHT...,  
CENTER... or USER... and press [Enter ]. You ll see the factory defaults of  
that item and Motion Detection will be applied to the area you selected.  
If you set the AREA menu to USER and press [ENTER], you may vary the size  
and position of the area where you want to apply the MOTION detection  
function by yourself. Press Left, Right, Up, or Down to select an area AREA.  
Press ENTER and then Left, Right, Up, or Down to select a LOCATION. Press  
ENTER again to move back to the upper menu.  
Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION  
detection area.  
Press [ENTER] again and you will escape the AREA setup menu.  
Use SENSITIVITY to set up the sensitivity of MOTION detection strength.  
The higher, the more sensitive.  
(CAMERA SET)  
(CAMERA SET)  
CAMERA ID  
V-SYNC  
OFF  
INT  
BW...  
OFF  
3
OFF  
OFF  
OFF  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
OFF  
INT  
BW...  
OFF  
3
COLOR/BW  
E
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
DISPLAY ZOOM  
DISPLAY P/T  
Use the  
[Left, Right]  
Keys  
X10  
DISPLAY ZOOM OFF  
DISPLAY P/T  
OFF  
EXIT  
QUIT  
EXIT  
QUIT  
DISPLAY ZOOM  
AREA  
AREA  
In DISPLAY ZOOM, you can display the ZOOM scale on the screen.  
(CAMERA SET)  
X020  
Use the  
[Left, Right, Up, Down]  
Keys  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
OFF  
INT  
COLOR...  
OFF  
4
LOCATION  
LOCATION  
OFF  
DISPLAY ZOOM ON  
DISPLAY P/T  
OFF  
SAVE  
EXIT  
After PAN/TILT/ZOOM/FOCUS/IRIS movement finishes, MOTION DET function  
will not work for about 5 seconds to stablize the chage of the screen.  
If no change on the ZOOM scale is made for 3 seconds, the information window will  
MOTION detection function operates based on the brightness change within the  
setup region. Therefore, erroneous operation may occur depending on the  
brightness difference between the background and the object that is being  
taken, or the status of the area setup, etc.  
disappear.  
DISPLAY P/T  
In DISPLAY P/T, you can display the position of Pan/Tilt on the screen.  
ZOOM SPEED  
In the ZOOM SPEED menu you can select the speed of the ZOOM Key  
(CAMERA SET)  
347/060  
(Tele/Wide).  
CAMERA ID  
V-SYNC  
COLOR/BW  
MOTION DET  
ZOOM SPEED  
DIGITAL ZOOM  
OFF  
INT  
Use the [Left] or [Right] keys in the ZOOM SPEED menu to select  
the speed.  
1 : Slowest speed  
2 : Low speed  
3 : High speed  
4 : Fastest speed  
COLOR...  
OFF  
4
OFF  
DISPLAY ZOOM OFF  
DISPLAY P/T  
ON  
EXIT  
SAVE  
If no change on the Pan/Tilt position is made for 3 seconds, the information window  
will disappear.  
It allows an error range of 2°.  
3-8  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For items in the BLC menu, the user can set the size and location of the  
BLC area by pressing [ENTER] key after put the cursor on USERusing  
the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left,  
Right] key to designate the SIZE, and then press the [ENTER] key.  
You can set the location for areas using the [Up, Down, Left, Right] key in  
the LOCATION.  
EXIT  
The EXIT menu is used to quit the CAMERA SET menu of the  
SCC-C6403 and return to the MAIN MENU.  
- QUIT  
: Ignores the changed information and restores the saved  
information.  
- SAVE : Saves the information of the setting condition of the menu.  
- PRESET: Ignores the changed information and restores the initial  
factory defaults of the menu.  
(ALC)  
SIZE  
2. VIDEO SET MENU  
IRIS  
There is a function to automatically adjust IRIS to the incoming light level.  
Owing to this function, you may set up the brightness level yourself.  
The ALC(Auto Light Control) menu allows you for video output level setup.  
E
Press  
[Enter]  
BLC  
LEVEL  
RET  
USER...  
(0) ----I----  
LOCATION  
SIZE  
ALC  
SIZE  
Choose the ALC of the IRIS item and press [ENTER] and set he submenu  
to the Video Output level and BLC will be shown.The Video Output Level  
can be set in the level item using the [Left, Right] keys.  
Press  
BLC (Submenu of the ALC menu)  
[Enter]  
If you use a general camera to photograph a subject under backlight or  
bright illumination, the subject will be shown dark on the monitor due to  
the backlight. BLC(Back Light Compensation) is used to prevent such a  
backlight problem to secure distinct images under bright illumination.  
Using the [Left, Right] keys, you can set up BOTTOM, TOP, LEFT,  
RIGHT, CENTER5 preset areas and the USERfunction that can  
directly set the areas. For example, for the items in the BLC menu, you  
can confirm the preset BOTTOM area by pressing [ENTER] key in the  
BOTTOMstatus.  
LOCATION  
LOCATION  
Use [Left, Right] key in the LEVEL menu to control the video output  
level(brightness).  
(VIDEO SET)  
(ALC)  
IRIS  
ALC...  
AUTO X2...  
NORM  
ATW1  
---  
MANU  
SHUTTER  
MOTION  
WHITE BAL  
DIS  
FOCUS MODE ONEAF  
SPECIAL  
When you press [ENTER] key after selecting MANU in the IRIS item, an  
additional screen appears in which you can set manually opening or closing  
the IRIS.  
Press  
[Enter]  
BLC  
LEVEL  
RET  
OFF  
(0)----I ----  
...  
EXIT  
QUIT  
(VIDEO SET)  
(MANUAL)  
(ALC)  
IRIS  
SHUTTER  
AGC  
MANU...  
OFF  
OFF  
WHITE BAL  
DIS  
FOCUS MODE ONEAF  
SPECIAL  
EXIT  
ATW1  
OFF  
Press  
[Enter]  
Press  
LEVEL  
RET  
(00) ----I----  
...  
QUIT  
[Enter]  
BLC  
LEVEL  
RET  
BOTTOM...  
(0)----I----  
3-10  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SHUTTER  
AGC  
You may designate both the fast electronic shutter speed and low  
electronic shutter speed in the SHUTTER menu. The fast electronic  
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to  
be used for the bright and fast video image. The AUTO slow electronic  
shutter supports 12 shutter speeds from x2 to x160 and sets the shutter  
speed to be slow In order to make the image on the screen more distinct  
and brighter when you photograph under dark illumination. If you want to  
sense the light brightness to control the shutter speed to the brightness  
automatically, select the AUTO slow shutter.  
The AGC menu was designed to provide you with brighter screen  
supposed you photographed any subject in the dark resulting in less  
brighter image than regulated. AGC menu setup is available only when  
the SHUTTER menu is set to Fast Shutter or Off. Press either Left and  
Right to go to LOW or HIGH and the AGC function will be activated. LOW  
is use to lower the maximum AGC GAIN and HIGH raise the maximum  
AGC GAIN.  
(VIDEO SET)  
(VIDEO SET)  
E
IRIS  
SHUTTER  
AGC  
ALC...  
OFF  
LOW  
IRIS  
SHUTTER  
AGC  
ALC...  
OFF  
OFF  
WHITE BAL  
DIS  
ATW1  
OFF  
WHITE BAL  
DIS  
ATW1  
OFF  
FOCUS MODE  
SPECIAL  
EXIT  
ONEAF  
...  
QUIT  
FOCUS MODE  
SPECIAL  
EXIT  
ONEAF  
...  
QUIT  
Keep pressing both Left and Right in the SHUTTER menu, the speed will  
change in the following sequence.  
OFF AUTO X2... AUTO X4... AUTO X6... AUTO X8... AUTO X12... ❈  
AUTO X16... AUTO X24... AUTO X32... AUTO X48... AUTO X64... ❈  
AUTOX96... AUTO X128... OFF 1/100(1/120) 1/250 1/500 1/1000 ❈  
1/2000 1/4000 1/10K  
When the COLOR/BW menu of the camera set is set to AUTO..., AGC will  
be displayed as ---. You cant adjust the settings manually.  
MOTION  
The MOTION function is available only when the SHUTTER men is set to  
Slow Shutter AUTO, being composed of 5 steps, S.SLOW, SLOW,  
NORM, FAST, F.FAST.  
S.SLOW reduces the amount of AGC as much as possible to monitor  
subjects with no immobility in the dark.  
SLOW reduces the amount of AGC to monitor subjects with little  
immobility in the dark.  
If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be displayed  
as MF(the product can operate only in MF mode). You can t adjust the settings manually.  
If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product will recover the previous  
FOCUS mode.  
If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed as  
---(it can only operate in Off mode). You can t adjust the settings manually.  
If you set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.  
NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.  
FAST raises the amount of AGC to monitor fast subjects in the dark.  
F.FAST reduces the amount of AGC as much as possible to monitor  
very fast subjects in the dark.  
When the SHUTTER menu is set to AUTO, press Down to locate the  
cursor in the MOTION menu and press Left and Right for MOTION  
function setup. Press Left to the SLOW side and Right to the FAST side.  
FLICKERLESS  
Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is  
designed to avoid image flickering on the screen due to inconsistency between the  
vertical synchronizing frequency of the picture and the flashing frequency of the  
lightening. If you select and set AUTO to ON in SHUTTER from VIDEO SET, you can set  
NTSC or PAL for your area and the auto shutter speed is fixed at 1/100(1/120) second.  
(VIDEO SET)  
(FLICKERLESS)  
(VIDEO SET)  
IRIS  
ALC...  
AUTOX2...  
NORM  
ATW1  
---  
IRIS  
ALC...  
AUTO X2...  
F.FAST  
ATW1  
---  
ONEAF  
...  
QUIT  
SHUTTER  
MOTION  
WHITE BAL  
DIS  
SHUTTER  
MOTION  
WHITE BAL  
DIS  
FOCUS MODE  
SPECIAL  
EXIT  
Press  
[Enter]  
FOCUS MODE ONEAF  
FLICKERLESS  
RET  
OFF  
SPECIAL  
EXIT  
...  
QUIT  
3-12  
3-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You can select one of four modes for white balance adjustment as follows:  
WHITE BAL  
Lights are generally denoted as color temperatures and expressed in  
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the  
color temperature is monitored continuously and thereby white balance is  
set automatically. The following are the approximate supported color  
temperature ranges in these modes.  
Kelvin (  
K) units.  
The general light color temperatures are shown below.  
ATW1 : 2500K ~ 9300K(  
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(  
1. If the color temperature is out of this range in ATW1 mode, proper  
1)  
2)  
10000K  
9000K  
Blue sky  
white balance may not be obtained. In that case, select ATW2 mode.  
2. In ATW2 mode, if one color is dominated in the shooted area, the  
color can be displayed differently.  
Rainy  
E
Therefore, select the mode which is appropriate for the environment.  
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white  
balance is obtained by pressing [ENTER] while having a white paper in  
front of the camera. White Balance data will be maintained after set it  
once. AWC mode is best in locations where the color temperature of light  
source is constant.  
8000K  
7000K  
Cloudy  
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the  
white Balance considering the current illumination. Select MANU item  
and press [ENTER], the sub screen where you can select Manual White  
Balance will be shown. Use the left/right keys to select 3200K, 5600K or  
OFF(USER) mode in the PRESET menu.  
6000K  
Partly Cloudy  
Sunny  
5000K  
4000K  
- 3200  
K
K
: Set color temperature to 3200  
K
K
- 5600  
: Set color temperature to 5600  
- USER : Choose out a proper value from the RED and BLUE graph for  
color and temperature setup.  
Fluorescent lamp  
3000K  
Halogen lamp  
Candlelight  
(VIDEO SET)  
(AWB/MANU)  
IRIS  
SHUTTER  
AGC  
WHITE BAL  
DIS  
FOCUS MODE  
SPECIAL  
EXIT  
ALC...  
OFF  
LOW  
MANU...  
ON  
ONEAF  
...  
2000K  
1000K  
Press  
Tungsten lamp  
PRESET  
RET  
3200K  
[Enter]  
QUIT  
DIS  
The DIS(Digital Image Stabilization) function compensates the camera  
screen shaking incurred from vibration.  
It is recommended to deactivate the DIS function in the no vibration  
environment.  
From VIDEO SET, if you set SHUTTER to between AUTO X2... and AUTO  
X128... DIS will be displayed as ---(it can operate only in Off mode).  
You cant adjust the settings manually.  
3-14  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXIT  
FOCUS MODE  
It's the same as the EXIT function of the CAMERA SET menu.  
In the FOCUS MODE MENU, the Focus method can be set to ONEAF  
(One Auto Focus), or MF(Manual Focus).  
- ONEAF : In the ONEAF mode, it automatically sets the focus after the  
PAN/TILT/ZOOM moves, and operates as the same in the MF mode if the  
PAN/TILT/ZOOM does not move.  
3. PRESET  
This is the menu that user sets the PAN/TILT location, Zoom/Focus, and  
screen condition, so the camera can monitor the presetting area on  
demand. A total of 128 presets are available.  
- MF  
: In MANUAL FOCUS MODE the user adjusts the Focus manually.  
Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.  
(VIDEO SET)  
E
IRIS  
SHUTTER  
AGC  
WHITE BAL  
DIS  
ALC...  
OFF  
OFF  
ATW1  
OFF  
** MAIN MENU **  
(PRESET MAP)  
CAMERA SET...  
FOCUS MODE  
SPECIAL  
EXIT  
ONEAF  
...  
QUIT  
VIDEO SET...  
PRESET ...  
0
5
1
6
2
7
3
8
4
9
10 11 12 13 14  
15 16 17 18 19  
20 21 22 23 24  
25 26 27 28 29  
30 31  
ID:PRESET 0  
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
Press  
[Enter]  
ONEAF can only be selected if SHUTTER is set to OFF, 1/100(1/120)  
~1/10K, or AUTOX2...  
î
ï
RET  
In other modes (AUTOX4...~AUTOX128...), FOCUS mode will be  
displayed as MF(the product automatically switches into MF mode).You  
can t adjust the settings manually.  
ONEAF function may not possible withe types of objects listed below. For  
such objects, focus manually.  
PRESET NO.0  
POSITION SET  
PRESET ID  
VIDEO SET  
PRESET SPEED  
DWELL TIME  
IMAGE HOLD  
...  
- High intensity objects or objects illuminated with low lighting  
- Obejects shot through wet or dirty glass  
ON...  
OFF  
8
3S  
OFF  
Press  
- Pictures that are a mixture of distant and nearby objects  
- White alls and other single-color objects  
- Venetian blinds and other horizontally striped objects  
[Enter]  
EXIT  
QUIT  
SPECIAL  
In SPECIAL menu, you can directly adjust Y-LEVEL, C-LEVEL, and DETAIL  
functions.  
- Y-LEVEL : It is used to set the levels for the Sync signal and the entire  
brightness signal of the video signal.  
- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour  
signal of the video signal.  
- DETAIL : Controls both horizontal and vertical distinction.  
(VIDEO SET)  
(SPECIAL)  
IRIS  
SHUTTER  
AGC  
ALC...  
OFF  
ON  
WHITE BAL  
DIS  
ATW1  
ON  
Press  
Y-LEVEL  
C-LEVEL  
DETAIL  
RET  
(0)I--------  
(0)I--------  
(0)--I-  
FOCUS MODE  
SPECIAL  
ONEAF  
...  
[Enter]  
EXIT  
QUIT  
3-16  
3-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POSITION SET  
From "POSITION SET..." press [ENTER] to get into the PAN/TILT,  
FOCUS/ZOOM SET screen  
to set the PAN/TILT location and FOCUS/ZOOM condition then press  
[ENTER] to return to a higher menu.  
4. ZONE SET  
The ZONE SET menu includes the setup of ZONE DIRECTION, and  
ZONE AREA.  
** MAIN MENU **  
(ZONE SET)  
PRESET ID  
This is the ID set up function for each PRESET.  
It can be set up to 12 characters using the left, right, up, and down keys.  
The ID location can be set in the submenu of "LOCATION..."  
CAMERA SET...  
VIDEO SET...  
ZONE DIR SET  
OFF  
PRESET...  
ZONE AREA SET OFF  
E
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
Press  
[Enter]  
EXIT  
QUIT  
VIDEO SET  
This is the screen setting function for each PRESET.  
Refer to the explanation under "VIDEO SET menu".  
ZONE DIR SET  
PRESET SPEED  
Press the [Enter] key in the ZONE DIR SET ON…” mode to enter the  
SET NORTH screen. MAP. Move PAN to set the SET NORTH position  
and press [ENTER]. Based on the North position,the direction of N(North),  
NE(North-East), E(East), SE(South-East), S(South), SW(South-West),  
W(West), NW(North-West) is displayed whenever you move PAN.  
This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)  
to 8(FAST).  
- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec  
- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec  
DWELL TIME  
This is a function setting for the DWELL TIME of the PRESET location in  
"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.  
(ZONE SET)  
SET NORTH  
ZONE DIR SET  
ZONE AREA SET  
ON...  
OFF  
N
IMAGE HOLD  
Press  
Pauses the image when PRESET is in movement, If you set the IMAGE  
HOLD menu to ON, the screen will be paused until PRESET finishes  
moving.  
[Enter]  
EXIT  
QUIT  
EXIT  
"QUIT" : Does not save the selected information and returns to a higher  
menu.  
"SAVE" : Do saves the selected information and returns to a higher menu.  
"DEL" : Deletes the selected information and restores the DEFAULT.  
Then returns to a higher menu.  
3-18  
3-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZONE AREA  
LOCATION  
The LOCATION...menu designates the left/right LIMIT positions of  
ZONE AREA. Enter the setup screen to move PAN, then select a start  
position and press [ENTER]. Move PAN again  
to select a end position and press [ENTER]. Now, ZONE AREA setup is  
complete.  
Press [ENTER] to enter the ZONE AREA MAP screen from ZONE  
AREA SET.... Select a ZONE AREA number from the ZONE AREA MAP  
screen and press [ENTER] to enter the ZONE AREA setup screen.  
ZONE AREA SET  
0
SET START!  
LOCATION  
ZONE ID SET  
ZONE ENABLE  
...  
...  
ON  
(ZONE SET)  
(ZONE AREA MAP)  
ZONE DIR SET  
ZONE AREA SET  
OFF  
ON...  
E
0
4
1
5
2
6
3
7
*
After P/R/Z  
control, press  
[ENTER]  
Press  
[Enter]  
Press  
[Enter]  
EXIT  
QUIT  
EXIT  
QUIT  
SET END!  
After PAN control,  
press [ENTER] to  
finish.  
ZONE AREA SET  
0
LOCATION  
ZONE ID SET  
ZONE ENABLE  
...  
...  
ON  
Press  
[Enter]  
EXIT  
QUIT  
ZONE ID SET  
This function is used to allocate as many as 12 IDs to each zone area.  
Use Left , Right, UP, or DOWN for this purpose. You may select the ID  
position from the additional menu of LOCATION....  
ZONE AREA ID 0  
ZONE AREA SET  
0
A B C D E F G H I J K L  
M N O P Q R S T U V W X  
LOCATION  
ZONE ID SET  
ZONE ENABLE  
...  
...  
ON  
Y Z 0 1 2 3 4 5 6 7 8  
- +  
9
:
!
(
)
/
Press  
SP ï î SP  
LOCATION...  
RET  
[Enter]  
ZONE 0........  
EXIT  
QUIT  
ZONE ENABLE  
This function turns on or off the ZONE AREA ID indication.  
3-20  
3-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPEED  
5. AUTO SET  
This is a setting function for movement speed setup. It can be set from  
STEP1 to STEP64.  
The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is  
able to set up the AUTO PLAY motion.  
DWELL TIME  
This is a function for setting up the time to stay in the START to END position.  
AUTO PAN  
After selecting the locations of two points (PAN/TILT) of START and END,  
it loops continuously in the set up SPEED. The number of AUTO PAN is  
up to 4.  
PATTERN  
This is a replay function so that the MANUAL functions such as PAN, TILT,  
ZOOM, and FOCUS, IRIS are played for 2 minutes.  
E
** MAIN MENU **  
(AUTO SET)  
CAMERA SET...  
VIDEO SET...  
AUTO PAN  
PATTERN  
SCAN  
1...  
1...  
1...  
...  
PRESET...  
When the PATTERN is saved/executed, the PAN/TILT is operated with  
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
Press  
PROPORTIONAL ON, TURBO OFF.  
AUTO PLAY  
[Enter]  
If the SSC-1000 or SSC-2000 is used when uploading/downloading the  
menu setup, reset the PATTERN because it may be different with the first  
setting.  
RET  
AUTO PAN  
1
POSITION SET  
SPEED  
...  
22  
DWELL TIME  
3S  
Press  
[Enter]  
EXIT  
QUIT  
POSITION SET  
The menu POSITION SET …” sets the Start / End position of AUTO PAN.  
Return to the settings screen and set the desired START position for  
PAN/TILT, and then press the [ENTER] key. And, set the END position for  
the PAN/TILT. Press the [ENTER] key to finish the setup for AUTO PAN  
Start/End positions.  
3-22  
3-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
** MAIN MENU **  
CAMERA SET...  
VIDEO SET...  
PRESET...  
AUTO PLAY  
(AUTO SET)  
AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there  
is no camera action after AUTO RETURN finishes.  
AUTO PAN  
PATTERN  
SCAN  
1...  
1...  
1...  
...  
ZONE SET...  
Press  
Press  
AUTO SET...  
AUTO PLAY  
[Enter]  
[Enter]  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
(AUTO PLAY SET)  
RET  
(AUTO SET)  
AUTO RETURN 12HOUR  
AUTO PAN  
PATTERN  
SCAN  
1...  
1...  
1...  
...  
AUTO PLAY  
SCAN  
PATTERN SET 1  
PATTERN SET 1  
PLAY NUMBER  
1
Press  
SET START POSITION  
AND ENTER  
AUTO PLAY  
E
After  
PATTERN  
START  
[Enter]  
EXIT  
SAVE  
RET  
position setup,  
press  
[ENTER].  
AUTO RETURN  
This menu sets up the time during which AUTO PLAY repeats.  
PATTERN can be set upto 3. Choose 1, 2, or 3 with the left or right key in the  
"PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From  
the moment "PATTERN 1 SET" is gone for 2 minutes, it memorizes the MANUAL  
movements and after 2 minutes it will return to a higher menu. If you want to finish  
set up before the 2-minutes ends, press [ENTER].  
AUTO PLAY  
This function sets up the motion which will be repeatedly performed by  
SCC-C6403 whenever the time set by AUTO RETURN elapses. It covers SCAN,  
AUTO PAN, PATTERN, and PRESET setup.  
PLAY NUMBER  
This menu allocates a number to the motion set by AUTO PLAY. The numbers  
range from 1 to 4 for SCAN AND AUTO PAN, 1 to 3 for PATTERN, and 0 to 127  
for PRESET.  
SCAN  
SCAN sets the direction of PRESET movement during SCANoperation. The  
number of SCAN is up to 4 and each SCAN is able to allocate 32 PRESETs as a  
maximum.  
(SCAN MAP 1)  
(AUTO SET)  
0*S 1*  
2
7
3
8
4
9
AUTO PAN  
PATTERN  
SCAN  
1...  
1...  
1...  
...  
5
6
10 11 12 13 14  
15 16 17 18 19  
20 21 22 23 24  
25 26 27 28 29  
30 31  
EXIT  
Press  
AUTO PLAY  
[Enter]  
î
ï
SAVE  
RET  
If you enter the SCAN SET screen, SCAN MAP will be displayed. Move the cursor  
to the number marked * where PRESET is saved and press [ENTER] and  
S will appear and a PRESET will be included in SCAN.  
3-24  
3-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUTO SET  
6. ALARM SET  
This menu designates what to do at the time of ALARM input. Once an  
alarm is given, the camera will shortly move to the PRESET position  
corresponding to the respective alarm as follows.  
PRESET1 to ALARM1~4  
PRESET5 to MOTION  
After DWELL TIME at a PRESET position, PATTERN or SCAN will be in  
action according to the AUTO SET setup.  
It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an  
ALARM input from exterior SENSORs and it performs with PRESET or  
PATTERN function and outputs the ALARM OUT signals.  
Alarm operation time depends on the Preset Dwell time corresponding to  
the alarm and whether AUTO is involved.  
Setup of OFF/PATTERN 1~3/HALF1/HALF2/FULL/SCAN1~4 is available.  
OFF dues not perform PATTERN or SCAN after moved to PRESET and  
each menu has its own function as follows.  
** MAIN MENU **  
( ALARM SET)  
E
CAMERA SET...  
PATTERN 1~3 : Preset PATTERN action,  
ALARM PRIORITY SET ...  
ALARM IN SET..  
ALARM OUT SET..  
AUTO SET..  
VIDEO SET...  
PRESET...  
HALF1 : Continuous operation of PATTERN1 + PATTERN2  
HALF2 : Continuous operation of PATTERN2 + PATTERN3  
FULL : Continuous operation of all the aboves  
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
Press  
AUX OUT CONTROL..  
[Enter]  
SCAN 1~4 : Scanning as set  
RET  
AUX OUT CONTROL  
This sets the ALARM OUT motion to continue or act only when the  
ALARM is working.  
If it is set to OFF the ALARM OUT motion will operate only when the  
ALARM is working.  
(Active "Low"), and if it's set to ON, the ALARM OUT will always operate  
regardless of the ALARM.  
ALARM PRIORITY SET  
This sets the priority of the 4 ALARM inputs so ALARM can work  
corresponding to the priority.  
The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4.  
If the ALARM is working at the same time and the priority is the same, it  
will operate according to the DEFAULT priority. While the ALARM is  
working, it cannot detect MOTION.  
ALARM IN SET  
This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or  
"OFF" depending on the features of the SENSOR connected.  
7. OTHER SET  
PROPORTIONAL P/T  
This function controls the PAN/TILT speed to the ZOOM magnification  
ratio during the manual operation of PAN/TILT. If you set  
PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the  
ZOOM WIDE mode and decrease in the ZOON TELE mode even in the  
same manual operation.  
ALARM OUT SET  
Each ALARM input corresponds to one of the 3 ALARM OUT.  
3-26  
3-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(PASSWORD)  
TURBO P/T  
(OTHER SET)  
PROPORTIONAL P/T ON  
This function doubles up the speed of PAN/TILT movement by manual  
operation of PAN/TILT. The speed may go up to 180°/sec(PAN).  
0
5
1
6
2
7
3
8
4
9
TURBO P/T  
AUTO CAL.  
AUTO FLIP  
CAM RESET  
LANGUAGE  
PASSWORD  
OFF  
OFF  
ON  
...  
ENGLISH  
ON...  
❈  
❈  
Press  
[Enter]  
AUTO CAL  
This function turns on or off Auto Calibration. SCC-C6403 has the Auto  
Calibration function to improve the precision of LENS and PAN/TILT  
motor. You may set to OFF/6H/12H/18H/24H. Without users key input for  
the time designated by the user, A.C will appear on the screen while  
initializing LENS and PAN/TILT.  
RET  
EXIT  
QUIT  
Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and  
press [ENTER] for password setup. After you finish inputting the 4 digits  
password and the 2nd row of the 4 digits PASSWORD input screen, input  
the selected password again for reassurance.  
E
AUTO FLIP  
If correct, the cursor will move to RET.  
Press [ENTER] at RET, and the selected password will be saved,  
returning to the OTHER SET screen.  
Default password is 0123.  
When TILT is set to a 90° limit using the joystick, PAN automatically  
rotates by 180°  
enabling you to see up to the Tilt area on the opposite side .  
You can obtain an extended effect with the 180° operational range of the  
TILT feature.  
8. SYSTEM INFO  
This menu allows you to check S/W version, communication protocol,  
baud rate, and address of SCC-C6403.  
CAM RESET  
CAM RESET clears all the settings made so far and restores the factory  
default settings.  
"CAMERA RESET?" message appears when you select CAM RESET.  
Select "CANCEL" to return to the menu setup display or select OK to  
restore the factory default settings.  
** MAIN MENU **  
( SYSTEM INFO)  
CAMERA SET...  
ALARM VER. V1.000  
VIDEO SET...  
MOTOR VER. V1.000  
PRESET...  
CAMERA VER. V1.000  
EEPROM VER. V1.000  
ZONE SET...  
AUTO SET...  
ALARM SET...  
OTHER SET...  
SYSTEM INFO...  
Press  
[Enter]  
PROTOCOL  
SAMSUNG  
COMM. TYPE RS-485,HALF  
BAUD RATE  
ADDRESS  
SERIAL NO.  
RET  
9600  
❈❈ Be careful when performing a CAM RESET operation, as it deletes all  
0
000000000000000  
setup values.  
LANGUAGE  
This function selects a language for MENU setup. Press LEFT/RIGHT key to  
choose English, French, Spanish or Jepanese and the selected  
language will be applied to the full screen.  
PASSWORD  
This function selects or cancels the MENU setup password. Press  
[ENTER] at the state of PASSWORD ON..., and the following screen will  
appear for password setup.  
3-28  
3-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. SHORT KEYS  
SSC-1000 or SSC-2000 Controller supports the following short keys.  
Function  
Key  
CAMERA SET…  
COLOR/BW  
COLOR/BW  
COLOR/BW  
SCC-C6403 has two FANs inside for preventing overheating.  
If FAN doesn't work properly, messages below will be displayed.  
In those case, replace the FAN.  
COLOR  
BW  
[PRESET] + [1] + [2] + [8] + [Enter]  
[PRESET] + [1] + [2] + [9] + [Enter]  
[PRESET] + [1] + [3] + [0] + [Enter]  
AUTO  
- ALARM FAN ERROR !  
: This message is displayed when the FAN which is located bottom of  
SCC-C6403 does not work properly.  
VIDEO SET…  
IRIS  
E
ALC  
[PRESET] + [1] + [3] + [2] + [Enter]  
[PRESET] + [1] + [3] + [4] + [Enter]  
[PRESET] + [1] + [3] + [5] + [Enter]  
FOCUS MODE  
FOUCS MODE  
MF  
Contact your nearest Samsung Electronics Service Center or designated  
retailer before replacing the FAN.  
ONEAF  
ALARM SET…  
AUX OUT CONTROL…  
OUT1  
OUT1  
OUT2  
OUT2  
OUT3  
OUT3  
ON  
[PRESET] + [1] + [3] + [6] + [Enter]  
[PRESET] + [1] + [3] + [7] + [Enter]  
[PRESET] + [1] + [3] + [8] + [Enter]  
[PRESET] + [1] + [3] + [9] + [Enter]  
[PRESET] + [1] + [4] + [0] + [Enter]  
[PRESET] + [1] + [4] + [1] + [Enter]  
OFF  
ON  
OFF  
ON  
OFF  
OTHER SET…  
PROPORTIONAL P/T  
PROPORTIONAL P/T  
TURBO P/T  
ON  
[PRESET] + [1] + [4] + [2] + [Enter]  
[PRESET] + [1] + [4] + [3] + [Enter]  
[PRESET] + [1] + [4] + [4] + [Enter]  
[PRESET] + [1] + [4] + [5] + [Enter]  
[PRESET] + [1] + [4] + [6] + [Enter]  
[PRESET] + [1] + [4] + [7] + [Enter]  
OFF  
ON  
TURBO P/T  
OFF  
ON  
AUTO FLIP  
AUTO FLIP  
OFF  
[PRESET] + [1] + [4] + [8] + [Enter]  
[PRESET] + [1] + [4] + [9] + [Enter]  
[PRESET] + [1] + [5] + [0] + [Enter]  
AUTO RETURN *1)  
AUTO CAL.  
CAM RESET  
Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall  
be applied to the MENU setup process.  
1) The use of AUTO RETURN will be available only when the function  
equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.  
3-30  
3-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product specifications  
SCC-C6403  
Cautions  
NO  
Items  
Contents  
- Zoom lens single body SmartDome CAMERA  
- AC 24 10% (50Hz 0.3Hz)  
- 18W  
Remark  
1
Product Type  
Power Input  
The copyright of the manual belongs to Samsung Electronics Co., Ltd.  
2
Power Consumption  
3
Without the permission of Samsung Electronics it cannot be reproduced  
electronically, mechanically, audibly, or by any other method.  
4
Broadcasting Type  
Image Device  
- NTSC STANDARD COLOR SYSTEM  
- 1/4 inch 410K IT Type S-HAD CCD  
- 768(H) X 494(V)  
5
This manual will be modified according to product enhancements.  
6
Effective Pixels  
Scanning Mode  
7
- 525 Lines, 2:1 Interlace  
Scanning line  
Frequency  
- Horizontal : 15,734 Hz(INT) / 15,750 Hz(L/L)  
- Vertical : 59.94 Hz(INT) / 60 Hz(L/L)  
8
9
Synchronization Mode  
- INT/LINE LOCK  
- 480 TV LINES  
10  
11  
Resolution  
S/N Ratio  
- 50dB (AGC OFF)  
- COLOR : 0.3 Lux (30 IRE : Sense-Upx4)  
0.01 Lux (30 IRE : Sense-Up x128)  
- B/W : 0.03 Lux (30 IRE : Sense-Upx4)  
0.001 Lux (30 IRE : Sense-Up x128)  
Min. Object Illumination  
12  
- ATW1/ATW2/AWC/MANUAL MODE  
(3200K, 5600K, R/B GAIN Court)  
Color Temperature  
Signal Output  
13  
14  
-
COMPOSITE VIDEO OUT : 1.0Vp-p 75ohms/BNC  
- one body; 32x Zoom lens  
- Focal Length : 3.55 to 113 mm  
- Aperture : F1.69(Wide), F4.17(Tele)  
- MOD(Minimum Object Distance) : 2.5m  
15  
Lens  
- PAN range : 350° Non-Endless  
16  
17  
18  
PAN Function  
TILT Function  
- Preset Pan Speed : max 400°/sec  
- Manual Pan Speed : 0.1°~180°/sec (64step)  
- TILT range : 0°~90°  
- Preset TILT Speed : max 200°/sec  
- Manual TILT Speed : 0.1°~90°/sec (64step)  
- ZOOM(TELE/WIDE), FOCUS(NEAR/FAR),  
IRIS(OPEN/CLOSE), PAN/TILT, MENU  
RS-485 HALF/FULL Duplex, RS-422  
REMOTE  
CONTROL  
- Alarm Inputs : 4 IN(5mA Sink)  
- Alarm Outputs : 3 OUT (Open collector : 2  
DC24V 40mA Max, Relay : 1, NO, NC, COM  
2A 30VDC, 0.5A 125VAC Max)  
ALARM  
19  
- 10°C ~ +50°C  
20  
21  
Operation Temperature  
Operation Humidity  
- ~90%  
- DOME : 147 (ø),  
22  
23  
24  
SIZE  
- Outline : 159.6(ø) X 177(H)  
- 1.8Kg  
Weight  
4.5 Years  
Lives of Main Parts - FAN  
3-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Razor Games E100 User Guide
Regency Wraps Fire Pit U41 LP3 User Guide
Renesas Computer Hardware M30280T 85LGF User Guide
Revox Universal Remote Recontrol M207 User Guide
RoboteQ Computer Hardware AX500 User Guide
Roland Musical Instrument HP107 User Guide
RotoZip Saw DR1 User Guide
Salem Baking Company Kitchen Grill 252801 User Guide
Samsung Stereo System P10 User Guide
Sears Elliptical Trainer NTEX230120 User Guide