Samsung Clothes Dryer DV328 User Guide

DV337  
DV328  
Gas and Electric Dryer  
user manual  
imagine the possibilities  
Thank you for purchasing a Samsung product.  
To receive a more complete service,  
please register your product at  
DV337AEW-02453A-04_EN.indd  
1
2007-07-23 ¿ÀÈÄ 1:47:14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety instructions  
Congratulations on your new Samsung Dryer. This manual contains valuable  
information on the installation, use, and care of your appliance. Please take the  
time to read this manual to take full advantage of your dryers many benefits and  
features.  
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS  
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and  
situations that may occur. It is your responsibility to use common sense, caution, and care when installing,  
maintaining, or operating your dryer.  
Always contact your manufacturer about problems or conditions you do not understand.  
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS  
Hazards or unsafe practices that may result in severe personal injury or  
death.  
WARNING  
Hazards or unsafe practices that may result in minor personal injury or  
property damage.  
CAUTION  
Follow the information in this manual to minimize the risk of fire or explosion or  
to prevent property damage, personal injury, or death.  
Do not store or use gasoline or other flammable vapors and liquids near this or  
CAUTION  
any other appliance.  
Do NOT attempt.  
Do NOT disassemble.  
Do NOT touch.  
Follow directions explicity.  
Unplug the pwer plug from the wall socket.  
Make sure the machine is grounded to prevent electric shock.  
Call the service center for help.  
WHAT TO DO IF YOU SMELL GAS:  
Do not try to light any appliance.  
Do not turn on the appliance.  
Do not touch any electrical switch.  
Do not use any phone in your building.  
Clear the room, building or area of all occupants.  
Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers  
instructions.  
If you cannot reach your gas supplier, call the fire department.  
Installation and service must be performed by a qualified installer, service agency, or the gas  
supplier.  
Safety information _3  
DV337AEW-02453A-04_EN.indd  
3
2007-07-23 ¿ÀÈÄ 1:47:14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety instructions  
Read all instructions before using the appliance.  
To reduce the risk of fire or explosion:  
WARNING  
Do not dry items that have been previously cleaned, washed, soaked, or spotted with  
gasoline, dry cleaning solvents, or other flammable or explosive substances. They  
emit vapors that could ignite or explode. Any material that has been in contact with a  
cleaning solvent or flammable liquids or solids should not be placed in the dryer until all  
traces of these flammable liquids or solids and their fumes have been removed.  
There are many highly flammable items used in homes, such as acetone, denatured  
alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers,  
turpentine, waxes, and wax removers  
Items containing foam rubber (may be labeled latex foam) or similarly textured rubber-  
like materials must not be dried on a heat setting. Heated foam rubber materials can,  
under certain circumstances, produce fire by spontaneous combustion.  
Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is  
necessary when the appliance is used near children and pets.  
Before discarding or removing your dryer from service, remove the door to the drying  
compartment to prevent children or animals from becoming trapped inside.  
Do not reach into the appliance when the drum is moving.  
Do not install or store this appliance where it will be exposed to the weather.  
Do not tamper with controls.  
Do not repair, replace, or attempt to service any part of the appliance unless specifically  
recommended in the user-repair instructions and you understand and have the skills to  
carry those out.  
Do not use fabric softeners or products to eliminate static unless recommended for dryer  
use by the manufacturer of the fabric softener or product.  
Clean the lint screen before or after each load.  
Keep the area around the exhaust opening and surrounding areas free from lint, dust, and  
dirt.  
The interior of the dryer and exhaust duct should be cleaned periodically by qualified service  
personnel.  
This appliance must be properly grounded. Never plug the power cord into a receptacle  
that is not grounded adequately and in accordance with local and national codes. See  
installation instructions for grounding this appliance.  
Do not sit on top of the dryer.  
Because of continuing product improvements, Samsung reserves the right to change  
specifications without notice. For complete details, see the Installation Instructions  
packed with your product before selecting cabinetry, making cutouts, or beginning  
installation.  
Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie.  
coins, knives, pins, etc. These objects could damage your dryer.  
WARNING  
Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.  
4_ Safety information  
DV337AEW-02453A-04_EN.indd  
4
2007-07-23 ¿ÀÈÄ 1:47:14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Gas leaks may occur in your system, resulting in a dangerous situation.  
Gas leaks may not be detected by smell alone.  
WARNING  
Gas suppliers recommend you purchase and install a UL-approved gas detector.  
Install and use in accordance with the manufacturers instructions.  
Do not place items in your dryer that have been spotted or soaked with vegetable oil or  
cooking oil. Even after being washed, these items may contain significant amounts of these  
oils.  
The residual oil can ignite spontaneously. The potential for spontaneous combustion  
increases when the items containing vegetable oil or cooking oil are exposed to heat. Heat  
sources such as your dryer can warm these items, allowing an oxidation reaction in the  
oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot  
enough to catch fire. Piling, stacking, or storing these kinds of items may prevent heat from  
escaping and can create a fire hazard.  
All washed and unwashed fabrics that contain vegetable oil or cooking oil can be  
dangerous. Washing these items in hot water with extra detergent will reduce, but not  
eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their  
temperature. Never remove these items from the dryer hot or interrupt the drying cycle until  
the items have run through the Cool Down cycle. Never pile or stack these items when they  
are hot.  
Safety information _5  
DV337AEW-02453A-04_EN.indd  
5
2007-07-23 ¿ÀÈÄ 1:47:15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
contents  
7
7
8
9
9
9
Tools needed for installation  
See Exhaust Requirements  
Ducting requirements  
Important to installer  
location considerations  
Alcove or closet installation  
INSTALLING YOUR DRYER  
7
10 Mobile home installation  
10 Exhausting  
11 Gas requirements  
12 Electrical requirements  
12 Grounding  
13 Electrical connections  
13 Replacement parts and accessories  
14 Installation  
15 Final installation checklist  
16 Dryer Exhaust Tips  
17 Door Reversal  
18 Overview of the control panel  
20 Child lock  
OPERATING INSTRUCTIONS, TIPS  
20 My cycle  
21 Rack Dry  
22 Clean the lint filter  
22 Load the dryer properly  
22 Getting started  
18  
23 Control Panel  
23 Tumbler  
23 Stainless Steel Tumbler  
23 Dryer Exterior  
23 Dryer Exhaust System  
CARE AND CL2EAN3ING  
SPECIAL LAUND2RY T4IPS  
TROUBLESH2OOT5ING  
25 Check these points if your dryer…  
26 Information codes  
27 Fabric care chart  
28 Protecting the environment  
28 Declaration of conformity  
28 Specification  
APPENDIX  
27  
29 Cycle chart  
6_ Contents  
DV337AEW-02453A-04_EN.indd  
6
2007-07-23 ¿ÀÈÄ 1:47:15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
TOOLS NEEDED FOR INSTALLATION  
Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup,  
adjustment, and connection, it is considered the responsibility of the installer. If you install the dryer you are  
responsible.  
Make sure you have everything necessary for proper installation.  
1. A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.  
2. A POWER CORD for electric dryers (except Canada).  
3. GAS LINES (if a gas dryer) must meet national and local codes.  
4. EXHAUST SYSTEM – must be rigid metal or flexible stiff-walled metal exhaust ducting.  
SEE EXHAUST REQUIREMENTS  
Control panel  
Door  
Adjustable leg  
Pliers  
Level  
Cutting knife  
Pipe wrench (gas only)  
Nut drivers  
Phillips Screwdriver  
Duct tape  
Crescent spanner  
Installing your dryer _7  
DV337AEW-02453A-04_EN.indd  
7
2007-07-23 ¿ÀÈÄ 1:47:18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
DUCTING REQUIREMENTS  
Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.  
Do not use a smaller duct.  
Ducts larger than 4 inches (10.2 cm) in diameter can result in increased lint accumulation.  
Lint accumulation should be cleaned regularly.  
If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct  
with a thin foil wall. Serious blockage can result if the flexible metal duct is bent too sharply.  
Never install any type of flexible duct in walls, ceilings, or other concealed spaces.  
Keep the exhaust duct as straight and short as possible.  
Secure joints with duct tape. Do not use screws.  
DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE, OR CONCEALED SPACE OF  
A BUILDING, GAS VENT, OR ANY OTHER COMMON DUCT OR CHIMNEY.  
THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER.  
Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times, and affect dryer  
operation.  
Exhaust systems longer than recommended can extend drying times, affect machine operation, and  
may collect lint.  
The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and  
entry of wildlife. Never use an exhaust hood with a magnetic damper.  
The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and  
the ground or other obstruction. The hood opening should point down.  
Never install a screen over the exhaust outlet.  
To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house  
or porch.  
If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly  
down towards the exhaust hood to reduce condensation and lint buildup.  
Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before  
cleaning.  
Check frequently to be sure the exhaust hood damper opens and closes freely.  
Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then  
check ducting for obstructions.  
ELECTRIC AND GAS DRYER  
Weather Hood Type  
Recommended  
Use only for short-run installation  
4” (10 .16 cm)  
2.5” (6.35 cm)  
No. of 90° elbows  
Rigid  
Metallic Flexible*  
12.4 m (41 ft.)  
11.2 m (37 ft.)  
10.1 m (33 ft.)  
9.0 m (29 ft.)  
Rigid  
Metallic Flexible*  
10.1 m (33 ft.)  
8.8 m (29 ft.)  
7.6 m (25 ft.)  
6.5 m (21 ft.)  
0
1
2
3
24.4 m (80 ft.)  
20.7 m (68 ft.)  
17.4 m (57 ft.)  
14.3m (47 ft.)  
22.6 m (74 ft.)  
18.9 m (62 ft.)  
15.5 m (51 ft.)  
12.5 m (41 ft.)  
*
Do not use non-metallic flexible duct.  
8_ Installing your dryer  
DV337AEW-02453A-04_EN.indd  
8
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the new dryer is installed into an existing exhaust system you must make  
sure:  
The exhaust system meets all local, state, and national codes.  
That a flexible plastic duct is not used.  
To Inspect and clean all lint buildup from inside the existing duct.  
The duct is not kinked or crushed.  
The exhaust hood damper opens and closes freely.  
The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be  
less than 0.  
This can be measured with the dryer running with a manometer at the point where the exhaust  
duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be  
empty and the lint filter clean.  
IMPORTANT TO INSTALLER  
Please read the following instructions carefully before installing the dryer. These instructions should be kept  
for future reference.  
REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD  
SUFFOCATING.  
WARNING  
LOCATION CONSIDERATIONS  
The dryer should be located where there is enough space in front for loading the dryer, and enough space  
behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or  
the left, use the accessory exhaust kit. Instructions are included with the kit. Its important to make sure the  
room has enough fresh air. The dryer must be located where there is no air-flow obstruction.  
On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air  
for combustion and proper dryer operation.  
THE DRYER MUST NOT BE INSTALLED OR STORED IN AN AREA WHERE IT WILL BE EXPOSED TO  
WATER AND/OR WEATHER. THE DRYER AREA IS TO BE KEPT CLEAR OF COMBUSTIBLE MATERIALS,  
GASOLINE, AND OTHER FLAMMABLE VAPORS AND LIQUIDS. A DRYER PRODUCES COMBUSTIBLE  
LINT. THE AREA AROUND THE DRYER SHOULD BE KEPT LINT-FREE.  
ALCOVE OR CLOSET INSTALLATION  
The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or  
WARNING  
closet.  
No other fuel-burning appliance should be installed in the same closet as the dryer.  
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED TO THE OUTDOORS.  
See EXHAUST INFORMATION section.  
Minimum clearances between the dryer and adjacent walls or other surfaces are:  
2” in front, 17” on top, 1” on either side, and 2.375” in the back.  
The closet front must have two unobstructed air openings for a combined minimum total area of 72 in²  
with 3” minimum clearance on the top and bottom. A louvered door with equivalent space clearance is  
acceptable.  
Installing your dryer _9  
DV337AEW-02453A-04_EN.indd  
9
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
MOBILE HOME INSTALLATION  
The installation of the dryer in mobile homes must conform to the Manufactured Home Construction and  
Safety Standard Title 24 CFR, Part 32-80 {formerly the Federal Standard for Mobile Home Construction and  
Safety, Title 24, HUD (Part 280), 1975} for the United States) or CSA Standards Z240 (for Canada).  
When installing a dryer in a mobile home, provisions for anchoring the dryer to the floor must be made.  
Locate an area that has adequate fresh air.  
A minimum of 72 in² (183 cm²) of unobstructed space is required.  
Call 1-800-SAMSUNG for information on purchasing the Floor Anchoring Kit as an accessory.  
All mobile home installations must be exhausted to the outside with the exhaust duct termination securely  
fastened to the mobile home structure, using materials that will not support combustion.  
The exhaust duct may not terminate underneath the mobile home.  
See Exhausting section for more information.  
EXHAUSTING  
Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the  
room.  
In the United States:  
All dryers must be exhausted to the outside.  
Only a rigid or flexible metal duct should be used for exhausting.  
In Canada:  
All dryers must be exhausted to the outside.  
Outside the U.S. and Canada:  
Refer to local codes.  
The dryer must be exhausted to the outside to reduce the risk of fire when installed in an  
alcove or closet.  
WARNING  
NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT.  
If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.  
Use only a metal exhaust duct that is non-flammable to ensure containment of exhaust air,  
heat, and lint.  
10_ Installing your dryer  
DV337AEW-02453A-04_EN.indd 10  
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
GAS REQUIREMENTS  
Use only natural or LP (liquid propane) gases.  
THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL  
CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED  
STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).  
Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP  
(liquid propane) gas, it must be converted for safe and proper performance by a qualified service technician.  
A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas  
line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-off  
valve be installed within 6’ of your dryer.  
Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.  
Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge  
connection, must be installed immediately upstream of your dryers gas supply connection.  
Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the  
system.  
DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas  
Association (CGA in Canada).  
Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.  
As a courtesy, most local gas utilities will inspect a gas appliance installation.  
GAS IGNITION Your dryer uses an automatic ignition system to ignite the burner.  
There is no constant burning pilot.  
Commonwealth of Massachusetts installation instructions  
Your dryer must be installed by a licensed plumber or gas fitter. A T” handle manual gas valve  
must be installed in the gas supply line to your dryer. If a flexible gas connector is used to install  
your dryer, the connector must have a maximum length of 3’ (36”).  
-
-
-
-
Gas leaks may occur in your system, creating a dangerous situation.  
Gas leaks may not be detected by smell alone.  
Gas suppliers recommend you purchase and install a UL-approved gas detector.  
Install and use in accordance with manufacturers instructions.  
WARNING  
Installing your dryer _11  
DV337AEW-02453A-04_EN.indd 11  
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
ELECTRICAL REQUIREMENTS  
Wiring diagram is located on plate below the control panel.  
Improper connection of the equipment grounding conductor can result in a risk of electric shock.  
Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is  
properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet,  
have a proper outlet installed by a qualified electrician.  
WARNING  
To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding  
must be done in accordance with local codes, or in the absence of local codes, with the National  
Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code  
CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide  
adequate electrical services for your dryer.  
All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest  
Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and  
local codes and ordinances.  
GROUNDING  
This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of  
electrical shock by providing a path of least resistance for the electrical current.  
Gas models  
Your dryer has a cord with an equipment-grounding conductor and a grounding plug.  
The plug must be plugged into an appropriate outlet that is properly installed and grounded in  
accordance with all local codes and ordinances.  
Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet  
installed by a qualified electrician.  
NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT  
WATER PIPES.  
Electric models  
Your dryer has a cord with an equipment-grounding conductor and a grounding plug, sold  
separately.  
The plug must be plugged into an appropriate outlet that is properly installed and grounded in  
accordance with all local codes and ordinances.  
If a power cord is not used and the electric dryer is to be permanently wired, the dryer must  
be connected to a permanently grounded metal wiring system, or an equipment grounding  
conductor must be run with the circuit conductors and connected to the equipment grounding  
terminal.  
12_ Installing your dryer  
DV337AEW-02453A-04_EN.indd 12  
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELECTRICAL CONNECTIONS  
Before operating or testing, follow all grounding instructions in the Grounding section.  
An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN  
EXTENSION CORD.  
Gas models – U.S. and Canada  
A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is  
required.  
Electric models – U.S. only  
Most U.S. dryers require a 120/240 volt, 60 Hz AC approved electrical service. Some require  
120/208 volt, 60 Hz approved electrical service. The electric service requirements can be found  
on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of  
the line is required.  
If a power cord is used, the cord should be plugged into a 30-ampere receptacle.  
The power cord is NOT provided with U.S. electric model dryers.  
IMPORTANT:  
When local codes allow, the dryer electrical supply may be connected by means of a new power  
supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of120/240  
volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop  
terminals, open-end spade lugs with turned up ends, or with tinned leads.  
1. size of the conductors and the type of cord.  
2. 3/4” (1.9 cm) UL-listed strain relief  
Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring  
must be retained at the dryer cabinet with a suitable UL-listed strain relief.  
Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations,  
(2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit  
grounding through the neutral conductor. (Use 4-prong plug for 4 wire receptacle, NEMA  
type 14-30R.)  
Electric models – Canada Only  
A 120/240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or  
circuit breaker on both sides of the line is required.  
All Canadian models are shipped with the power cord attached. The power cord should be  
plugged into a 30-ampere receptacle.  
It is not permissible to convert a dryer in Canada to 208 volts.  
REPLACEMENT PARTS AND ACCESSORIES  
If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your  
dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).  
Installing your dryer _13  
DV337AEW-02453A-04_EN.indd 13  
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
INSTALLATION  
For proper installation, it is highly recommended to hire a professional. To install:  
1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-  
by-side, to allow access to gas, electrical, and exhaust connections.  
Lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it will lay across both  
cushion-tops.  
2. Set your dryer back in an upright position.  
3. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer  
to the exhaust hood. The crimped end of the duct sections must point away from your dryer.  
DO NOT use sheet metal screws when assembling ducting. These joints should be taped.  
Never use plastic flexible exhaust material.  
Tip for tight installations: install a section of exhaust system to your dryer before putting it in place.  
Use duct tape to secure this section to your dryer, but do not cover ventilation slots at the back of the  
unit in dryer cabinet.  
4. Review Electrical Requirements section.  
BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section.  
U.S. MODELS:  
IMPORTANT – All U.S. models are produced for a 3-WIRE SYSTEM CONNECTION.  
The dryer frame is grounded to the neutral conductor at the terminal block.  
A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile  
homes, or if local codes do not permit grounding through neutral. If the 4-wire system is used,  
the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the  
following instructions for 3- and 4-WIRE SYSTEM CONNECTIONS.  
Remove the terminal block cover plate.  
Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the  
terminal block.  
A strain relief must be used.  
Do not loosen the nuts already installed on the terminal block. Be sure they are tight.  
Use a 3/8” (1cm) deep well socket.  
5. Review Gas Requirements section.  
Remove the pipe thread protective cap.  
Apply pipe joint compound or about 1 1/2 wraps of Teflon tape over all threaded connections.  
Pipe joint compound must be resistant to the action of any liquefied petroleum gas.  
Connect the gas supply to your dryer.  
An additional fitting is required to connect the 3/4” (1.9 cm) female thread end of a flexible connector to  
the 3/8” (1 cm) male threaded end on the dryer.  
Securely tighten the gas line fitting over threads.  
Turn on the gas supply. Check all gas connections for leaks using a soap solution.  
If bubbles appear, tighten the connections and recheck.  
DO NOT use an open flame to check for gas leaks.  
14_ Installing your dryer  
DV337AEW-02453A-04_EN.indd 14  
2007-07-23 ¿ÀÈÄ 1:47:21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-WIRE system connections  
1. Loosen or remove the center terminal block screw.  
2. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored  
terminal screw of the terminal block. Tighten screw.  
3. Connect the other wires to outer terminal block screws. Tighten screws.  
4. Tighten the strain relief screws.  
5. Insert the tab of the terminal block cover into your dryers rear panel slot.  
Secure the cover with a hold-down screw.  
1. External ground connector  
2. Neutral grounding wire (green/yellow)  
3. Center silver-colored terminal block screw  
4. Neutral wire (white or center wire)  
5. 3/4” (1.9 cm) UL-listed strain relief  
If converting from a 4-wire electrical system to a 3-wire, the ground strap must be  
reconnected to the terminal block support to ground the dryer frame to the neutral  
WARNING  
conductor.  
4-WIRE system connections  
1. Remove the center terminal block screw.  
2. Connect the ground wire (green or unwrapped) of the power cord to the external ground  
conductor screw.  
3. Connect the neutral wire (white or center wire) of the power cord and the appliance ground  
wire (green with yellow stripes) under the central screw of the terminal block.  
4. Connect the other wires to the outer terminal block screws. Tighten screws.  
5. Tighten the strain relief screws.  
6. Insert the tab of the terminal block cover into your dryers rear panel slot.  
Secure the cover with a hold-down screw.  
1. External ground connector  
2. Green or bare copper wire of power cord  
3. 3/4 in. (1.9 cm) UL-listed strain relief  
4. Center silver-colored terminal block screw  
5. Grounding wire (green/yellow)  
6. Neutral wire (white or center wire)  
6. With a level, check your dryer and make necessary adjustments to the leveling legs.  
7. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are  
complete. Plug in your dryer, and check operation by using the checklist below.  
8. (GAS MODELS ONLY)  
The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat  
setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5  
minutes. Be sure the gas supply to your dryer has been turned on. In order to confirm gas ignition,  
check the exhaust for heat.  
FINAL INSTALLATION CHECKLIST  
Dryer is plugged into electrical outlet and properly grounded.  
Exhaust ductwork is hooked up and joints taped.  
Plastic flexible duct is NOT used.  
Used rigid or stiff-walled flexible metal vent material.  
Dryer is level with all legs firmly on the floor.  
Gas models – gas is turned on with no gas leaks.  
Start your dryer to confirm that it runs, heats, and shuts off.  
Installing your dryer _15  
DV337AEW-02453A-04_EN.indd 15  
2007-07-23 ¿ÀÈÄ 1:47:22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
installing your dryer  
DRYER EXHAUST TIPS  
Plastic or non-metal flexible duct presents a potential fire hazard.  
WARNING  
1. Let your dryer exhaust the air easily.  
2. Use 4” diameter rigid metal duct. Tape all joints, including at  
the dryer.  
Never use lint-trapping screws.  
3. Keep ducts as straight as possible.  
4. Clean all old ducts before installing your new dryer.  
Be sure vent flap opens and closes freely.  
Inspect and clean the exhaust system annually.  
Don’t let a poor exhaust system slow drying by:  
1. Restricting your dryer with a poor exhaust system.  
2. Using a plastic, thin foil, or non-metal flexible duct.  
3. Using unnecessarily long duct runs with many  
1
2
4
elbows.  
4. Allowing crushed or clogged ducts and vent.  
3
16_ Installing your dryer  
DV337AEW-02453A-04_EN.indd 16  
2007-07-23 ¿ÀÈÄ 1:47:24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DOOR REVERSAL  
1. Unplug the power cord.  
8. Reassemble the black  
screw in the other hole.  
2. Remove two door hinge  
screws.  
3. Lift the door and remove  
from the dryer.  
4. Remove a screw on the  
9. Reassemble the screw  
(Step 4) on the Frame  
Front  
Frame Front  
5. Remove two screws on  
the opposite side of the  
door hinge.  
10. Place the door on the  
other side and reattach it  
to the dryer.  
6. Remove two screws from  
11. Reassemble the holder  
the holder lever.  
lever.  
7. Remove one black screw  
12. Reassemble the screws in  
from the door hinge.  
the remaing holes.  
The screw mentioned in STEP 4 may not exist.  
WARNING  
Installing your dryer _17  
DV337AEW-02453A-04_EN.indd 17  
2007-07-23 ¿ÀÈÄ 1:47:28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
operating Instructions, tips  
OVERVIEW OF THE CONTROL PANEL  
1
7
2
3
6
4
5
7
8
9
10  
The display window shows the estimated time remaining in the cycle after the  
Start/Pause button is pressed. The estimated time remaining may fluctuate as the  
cycle progresses.  
The Drying light will illuminate and remain lit until the cycle is complete.  
When your dryer is in the cool-down phase, the Cooling light will illuminate.  
When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will  
illuminate.  
Digital Graphic  
Display  
1
When the cycle is complete, “END” will appear in the display panel until the dryer  
door is opened or Power key is pushed.  
If your dryer is paused during a cycle, the indicator lights will blink until the Start/  
Pause button is pressed.  
To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles,  
press the Dry Level button. An indicator light will illuminate next to the desired  
dryness level.  
Dry Level  
Selection Button  
Press the button repeatedly to scroll through the settings. Larger or bulkier loads  
may require the Very Dry or More Dry setting for complete dryness.  
2
The Less Dry setting is best suited for lightweight fabrics or for leaving some  
moisture in the clothing at the end of the cycle. Damp Dry is designed to partially  
dry items. Use for items that lay flat or hang to dry.  
To select the correct temperature for the load, press the Temp button. An indicator  
light will illuminate next to the desired temperature. Press the button repeatedly to  
scroll through the settings.  
High – For sturdy cottons or those labeled Tumble Dry.  
Medium – For permanent press, synthetics, lightweight cottons, or items labeled  
Tumble Dry Medium.  
Temp Selection  
Button  
3
Medium Low – For lower heat than Medium to dry synthetic or washable knit fabrics.  
Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.  
Extra Low – Provides the lowest heated dry temperature possible.  
18_ Operating Instructions, Tips  
DV337AEW-02453A-04_EN.indd 18  
2007-07-23 ¿ÀÈÄ 1:47:29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When using Manual Dry cycles, time can be adjusted by pressing the time  
selection button.  
During the Sensory Dry cycle, the time light indicator is off because exact drying  
times are determined by fluctuating humidity levels.  
Time Selection  
Button  
4
5
When the cycle is complete, a chime will sound.  
When the Wrinkle Prevent option is selected, the chime will sound intermittently.  
Adjust the volume of the chime or turn it off by pressing the Signal button.  
Press the button repeatedly to scroll through the choices.  
Signal Selection  
Button  
Wrinkle Prevent provides approximately 90 minutes of intermittent tumbling in  
unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle Prevent  
button to activate this feature.  
The indicator light above the pad will illuminate when Wrinkle Prevent is selected.  
The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.  
Wrinkle Prevent  
Selection Button  
6
Adjust Time – Time can be added or subtracted from the automatically set times  
in the Manual Dry cycles (Time Dry, Freshen Up, Delicates, Wrinkle Release, or Air  
Fluff cycles).  
To add or subtract time from the cycle, press the Adjust Time arrow pad up or  
down until the desired time is displayed.  
My Cycle – Choose your favorite cycle including cycle, temp, dry level option,  
Select Cycle  
Option  
7
etc. (See page 20 for detail.)  
Rack Dry – Rack Dry is available at Time Dry cycle. Temperature will be set only  
to Extra Low. (See page 21 for detail.)  
To select a cycle, rotate the Cycle Selector dial to the desired cycle.  
The indicator light by the cycle name will illuminate. The Normal, Heavy Duty,  
Towels, Perm Press and Delicates cycles are Sensor Dry cycles.  
Sensor Dry automatically senses the moisture in the load and shuts the dryer off  
when the selected dryness level (very dry to damp dry) is reached.  
Normal – Use this cycle to dry loads such as cotton, underwear, and linen.  
Heavy Duty – Use this cycle to get high heat for heavy fabrics such as jeans,  
corduroys, or work clothes.  
Towels – Dry loads such as bath towels.  
Perm Press – Dry wrinkle-free cottons, synthetic fabrics, knits, and permanent  
press fabrics automatically. The cycle minimizes wrinkling by providing a longer  
unheated cool-down period at the end of the cycle.  
Cycle Selector  
8
Delicates – The Delicates cycle is designed to dry heat-sensitive items at a low  
drying temperature.  
Freshen Up – This cycle removes odors and freshens garments.  
Time Dry – Time Dry allows you to select the desired cycle time in minutes.  
Turn the Cycle Selector dial to Time Dry, then press the Adjust Time up arrow to  
set the drying time.  
Press the arrow repeatedly to scroll through the time settings.  
Wrinkle Release – The Wrinkle Release cycle will release wrinkles from items that  
are clean, dry, and only slightly wrinkled, such as clothes from a crowded closet,  
suitcase or items that have been in the dryer too long after the cycle has ended.  
Wrinkle Release can be used with any temperature selection.  
Air Fluff – The Air Fluff cycle tumbles the load in room temperature air.  
Start/Pause  
selection button  
9
Press to pause and restart programs.  
Press once to turn your dryer on, press again to turn it off. If your dryer is left  
on for more than 10 minutes without any buttons being touched, the power  
automatically turns off.  
10  
Power button  
Operating Instructions, Tips _19  
DV337AEW-02453A-04_EN.indd 19  
2007-07-23 ¿ÀÈÄ 1:47:32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
operating Instructions, tips  
CHILD LOCK  
A function to prevent children from playing with your dryer.  
Setting/Releasing  
If you want to set or release the Child Lock, press both the Time and Signal buttons  
simultaneously for 3 seconds.  
How to Set:  
1. It can be set while your dryer is running.  
2. Once you set the Child Lock function, no button, except for the Power button, can be  
controlled until you release the Child Lock function.  
3. The Child Lock indicator will be lit.  
1. If the dryer is powered on again, the Child Lock function stays on.  
2. To release that function, follow the instructions above.  
When other buttons, except for the Power button, do not respond, check the Child Lock  
indicator.  
MY CYCLE  
Lets you activate your customized cycle that includes Dry Level, Temp, Time option, etc.  
By pushing the My Cycle button, you activate the settings used during the previous My Cycle mode.  
(Default : Normal Cycle)  
If My Cycle mode is activated, My Cycle lamp will be lit.  
You can select all options in My Cycle mode as follows.  
1. Select cycle using Cycle Selector dial.  
2. After cycle selection, set each option.  
Each cycle has certain default options that are automatically set.  
To see these default options, go to page F-3.  
3. Then, you can start My Cycle by pushing the Start/Pause button in My Cycle mode. The cycle and  
options you select will be displayed the next time you choose My Cycle.  
You can change the My Cycle settings by repeating same process above.  
The last used setting will be displayed the next time you choose My Cycle.  
20_ Operating Instructions, Tips  
DV337AEW-02453A-04_EN.indd 20  
2007-07-23 ¿ÀÈÄ 1:47:32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RACK DRY  
Installing the drying rack  
1. Open the dryer door.  
2. Position the drying rack in the tumbler, placing the rear legs in the two recessed areas of the  
dryers back wall.  
3. Place the front lip of the drying rack on top of the lint filter.  
4. Place the items to be dried on the rack, leaving space between them so air can reach all  
surfaces.  
5. Close dryer door.  
6. Use the Time Dry cycle. Select the time according to the moisture and weight of the items.  
Start dryer. It may be necessary to reset the timer if a longer drying time is needed.  
SUGGESTED ITEMS  
SUGGESTED TEMP. SETTINGS  
Washable sweaters  
Heat (Low/Extra Low)  
(block to shape and lay flat on rack)  
Stuffed toys  
(cotton or polyester fiberfilled)  
Heat (Low/Extra Low)  
Air Fluff  
Stuffed toys  
(foam or rubber-filled)  
Foam rubber pillows  
Sneakers  
Air Fluff  
Fluff or Heat  
Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the item and  
lead to a fire hazard.  
WARNING  
Operating Instructions, Tips _21  
DV337AEW-02453A-04_EN.indd 21  
2007-07-23 ¿ÀÈÄ 1:47:33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
operating Instructions, tips  
CLEAN THE LINT FILTER  
After each load.  
To shorten drying time.  
To operate more energy efficiently.  
Do not operate your dryer without the lint filter in place.  
LOAD THE DRYER PROPERLY  
Place only one washload in your dryer at a time.  
Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics  
being dry while heavy fabrics remaining damp at the end of a drying cycle.  
Add one or more similar items to your dryer when only one or two articles need drying.  
This improves the tumbling action and drying efficiency.  
Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some  
fabrics.  
GETTING STARTED  
1. Load your dryer loosely – DO NOT overload.  
2. Close the door.  
3. Select the appropriate cycle and options for the load (see pages B-2, B-3).  
4. Press the Start/Pause button.  
5. The dryer indicator light will illuminate.  
6. The estimated cycle time will appear in the display.  
The time may fluctuate to better indicate drying time remaining in the cycle.  
When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.  
Pressing Power cancels the cycle and stops your dryer.  
The Drying, Cooling, and Wrinkle Prevent indicator lights will illuminate during those portions of the  
cycle.  
22_ Operating Instructions, Tips  
DV337AEW-02453A-04_EN.indd 22  
2007-07-23 ¿ÀÈÄ 1:47:33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
care and cleaning  
CONTROL PANEL  
Clean with a soft, damp cloth. Do not use abrasive substances.  
Do not spray cleaners directly on the panel.  
The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.  
Apply such products away from your dryer and wipe up any spills or overspray immediately.  
TUMBLER  
Remove any stains such as crayon, ink, or fabric dye (from new items such as towels or jeans) with an all-  
purpose cleaner.  
Tumble old towels or rags to remove any excess stain or cleaning substance.  
Once these steps are done, stains may still be visible, but should not transfer to subsequent loads.  
STAINLESS STEEL TUMBLER  
To clean the stainless steel tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for stainless  
steel surfaces.  
Remove the cleaner residue and dry with a clean cloth.  
DRYER EXTERIOR  
Clean with a soft, damp cloth. Do not use abrasive substances.  
Protect the surface from sharp objects.  
DRYER EXHAUST SYSTEM  
Should be inspected and cleaned yearly to maintain optimum performance.  
The outside exhaust hood should be cleaned more frequently to ensure proper operation.  
Care and cleaning _23  
DV337AEW-02453A-04_EN.indd 23  
2007-07-23 ¿ÀÈÄ 1:47:33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
special laundry tips  
Please follow the care label or manufacturers instructions for drying special  
items. If care label instructions are not available, use the following information as  
a guide.  
Bedspreads & Comforters  
Follow the care label instructions or dry on the Normal cycle and  
High temperature.  
Make sure the item is thoroughly dry before using or storing.  
May require repositioning to ensure even drying.  
Blankets  
Use Normal and dry only one blanket at a time for best tumbling  
action.  
Make sure the item is thoroughly dry before using or storing.  
Curtains & Draperies  
Use the Perm Press cycle and Low or Extra Low temperature to help  
minimize wrinkling.  
Dry these in small loads for best results and remove as soon as  
possible.  
Cloth Diapers  
Use the Normal cycle and the High temperature setting for soft, fluffy  
diapers.  
Down–filled Items (jackets,  
sleeping bags, comforters,  
etc.)  
Use the Normal cycle and the Low or Extra Low temperature setting.  
Place a clean pair of sneakers in your dryer with the item to fluff the  
down comforters, etc. Adding a couple of dry towels shortens drying  
time and absorbs moisture.  
Foam Rubber (rug backs,  
stuffed toys, shoulder pads,  
etc.)  
DO NOT dry on a heat setting. Use the Air Fluff cycle (no heat).  
WARNING – Drying a rubber item with heat may damage it or be a  
fire hazard.  
Pillows  
Use the Normal cycle.  
Add a couple of dry towels and a pair of clean sneakers to help the  
tumbling action and to fluff the item.  
DO NOT dry kapok or foam pillows in dryer.  
Plastics (shower curtains,  
outdoor furniture covers,  
etc.)  
Use the Air Fluff cycle or the Time Dry cycle and the Low or Extra  
Low temperature setting depending on the care label instructions.  
THINGS TO AVOID :  
Fiberglass items (curtains, draperies, etc.).  
Woolens, unless recommended on the label.  
Vegetable or cooking oil-soaked items.  
24_ Special laundry tips  
DV337AEW-02453A-04_EN.indd 24  
2007-07-23 ¿ÀÈÄ 1:47:34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
troubleshooting  
CHECK THESE POINTS IF YOUR DRYER…  
PROBLEM  
SOLUTION  
doesn’t run.  
Be sure the door is latched shut.  
Be sure the power cord is plugged into a live electrical outlet.  
Check the homes circuit breaker and fuses.  
Press the Start/Pause button again if the door is opened during the  
cycle.  
doesn’t heat.  
doesn’t dry.  
Check the homes circuit breaker and fuses.  
Select a heat setting other than Air Fluff.  
On a gas dryer, check that the gas supply is on.  
Clean the lint filter and exhaust duct.  
Dryer may have moved into the cool-down phase of the cycle.  
Check all of the above, plus...  
Be sure the exhaust hood outside the home can open and close  
freely.  
Check exhaust system for lint buildup. Ducting should be inspected  
and cleaned annually.  
Use a 4” rigid metal exhaust duct.  
Do not overload. 1 wash load = 1 dryer load.  
Sort heavy items from lightweight items.  
Large, bulky items like blankets or comforters may require  
repositioning to ensure even drying.  
Check that the washer is draining properly to extract adequate water  
from the load.  
Load may be too small to tumble properly. Add a few towels.  
is noisy.  
Check the load for objects such as coins, loose buttons, nails, etc.  
Remove promptly.  
It is normal to hear the dryer gas valve or heating element cycle on  
and off during the drying cycle.  
Be sure the dryer is leveled properly as outlined in the installation  
instruction.  
It is normal for the dryer to hum from the high velocity of air moving  
through the dryer drum and exhaust system.  
Troubleshooting _25  
DV337AEW-02453A-04_EN.indd 25  
2007-07-23 ¿ÀÈÄ 1:47:34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
troubleshooting  
dries unevenly.  
Seams, pockets, and other similarly heavy areas may not be  
completely dry when the rest of the load has reached the selected  
dryness level. This is normal. Select the Very Dry setting if desired.  
If one heavy item is dried with a lightweight load, such as one towel  
with sheets, it is possible that the heavy item will not be completely  
dry when the rest of the load has reached the selected dryness level.  
Sort heavy items from lightweight items for best drying results.  
has an odor.  
Household odors from painting, varnishing, strong cleaners, etc.  
may enter the dryer with the surrounding room air. This is normal as  
the dryer draws the air from the room, heats it, pulls it through the  
tumbler, and exhausts it outside.  
When these odors linger in the air, ventilate the room completely  
before using the dryer.  
shuts off before load is dry  
Dryer load is too small. Add more items or a few towels and restart  
the cycle.  
Dryer load is too large. Remove some items and restart the dryer.  
INFORMATION CODES  
Information codes may be displayed to help you better understand what is occurring with your Dryer.  
CODE SYMBOL MEANING  
Heater temperature control  
SOLUTION  
Call for service. See below.  
problem.  
Door open sensing problem.  
Call for service. See below.  
Door open error When the door is Be sure the door is latched shut. If problem  
open, the dryer will not operate. continues, call for service. See below.  
For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG)  
26_ Troubleshooting  
DV337AEW-02453A-04_EN.indd 26  
2007-07-23 ¿ÀÈÄ 1:47:35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
FABRIC CARE CHART  
The following symbols provide garment care direction. The Clothing care labels include symbols for  
washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures  
consistency among garment manufacturers of domestic and imported items. Follow care label directions to  
maximize garment life and reduce laundering problems.  
Warning Symbols for  
Wash Cycle  
Normal  
Special Instructions  
Line Dry/ Hang to Dry  
Laundering  
Do Not Wash  
Permanent Press /  
Wrinkle Resistant /  
Wrinkle Control  
Drip Dry  
Dry Flat  
Do Not Wring  
Gentle/Delicates  
Hand Wash  
Do Not Bleach  
Heat Setting  
Do Not Tumble Dry  
No Steam (added to  
iron)  
Water Temperature**  
High  
Hot  
Medium  
Low  
Do Not Iron  
Warm  
Cold  
Dryclean  
Any Heat  
Dry Clean  
Bleach  
No Heat/Air  
Do Not Dry Clean  
Any Bleach (when  
needed)  
Iron-Dry or Steam  
Temperatures  
Line Dry/ Hang to Dry  
Drip Dry  
Only Non-Chlorine  
(color-safe)  
High  
Bleach (when needed)  
Tumble Dry Cycle  
Medium  
Low  
Dry Flat  
Normal  
Permanent Press/  
Wrinkle Resistant/  
Wrinkle Control  
Gentle/ Delicates  
** The dot symbols represent appropriate wash water temperatures for various items. The  
temperature range for Hot is 105° –125° F/ 41° – 52° C, for Warm 85° – 105° F/29° – 41° C and for  
Cold 60° – 85° F/16° – 29° C. (Wash water temperature must be a minimum of 60° F/16° C for  
detergent activation and effective cleaning.)  
Appendix _27  
DV337AEW-02453A-04_EN.indd 27  
2007-07-23 ¿ÀÈÄ 1:47:35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
appendix  
PROTECTING THE ENVIRONMENT  
This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance,  
please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be  
connected to a power source. Remove the door so that animals and small children cannot get trapped  
inside the appliance.  
DECLARATION OF CONFORMITY  
This appliance complies with UL2158.  
SPECIFICATION  
C
D
A
B
TYPE  
DIMENSION  
FRONT LOADING WASHER  
Div  
Inches (cm)  
Div  
Inches (cm)  
A. Height  
38” (96.5)  
C. Depth with  
door open 90°  
49” (124.5)  
B. Width  
27” (68.6)  
D. Depth  
30.25” (77.0)  
WEIGHT  
56.8 kg  
5300 W  
HEATER RATING  
POWER  
CONSUMPTION  
NO HEAT  
HEATING  
268 W  
5445 W  
28_ Appendix  
DV337AEW-02453A-04_EN.indd 28  
2007-07-23 ¿ÀÈÄ 1:48:02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CYCLE CHART  
Wrinkle  
prevent  
Default  
Drying  
Time  
Cooling  
Time  
Cycle  
Temp  
control  
Sensor dry  
level  
Time  
44 min  
60 min  
52 min  
34 min  
29 min  
Time  
90 min  
90 min  
90 min  
90 min  
90 min  
High  
(Medium)  
Normal  
Normal dry  
Normal dry  
Normal dry  
Normal dry  
Normal dry  
39 min  
55 min  
47 min  
24 min  
24 min  
5 min  
High (No  
change)  
Heavy Duty  
5 min  
High  
(Medium)  
Sensor Dry  
Towels  
Perm Press  
Delicates  
5 min  
Medium Low  
(No change)  
10 min  
5 min  
Low (No  
change)  
High (No  
change)  
Freshen Up  
Time Dry  
-
-
-
-
30 min  
40 min  
25 min  
20 min  
25 min  
35 min  
20 min  
5 min  
5 min  
5 min  
20 min  
High  
Manual Dry  
Wrinkle  
Release  
Medium  
Air Fluff  
- (No change)  
Appendix _29  
DV337AEW-02453A-04_EN.indd 29  
2007-07-23 ¿ÀÈÄ 1:48:04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
warranty  
SAMSUNG DRYER  
LIMITED WARRANTY TO ORIGINAL PURCHASER  
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.  
(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by  
SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:  
One (1) Year All Parts and Labor, Two (2) Years Control Board Parts  
This limited warranty begins on the original date of purchase, and is valid only on products purchased and  
used in the United States.  
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service  
procedures.  
Warranty service can only be performed by a SAMSUNG authorized service center.  
The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or  
SAMSUNGs authorized service center.  
SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability  
within the contiguous United States.  
In-home service is not available in all areas.  
To receive in-home service, product must be unobstructed and accessible to the service agent.  
If service is not available, SAMSUNG may elect to provide transportation of the product to and from an  
authorized service center.  
SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,  
with new or reconditioned parts or products if found to be defective during the limited warranty period  
specified above.  
All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG.  
Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is  
longer.  
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal,  
noncommercial use of this product and shall not apply to the following: damage that occurs in shipment;  
delivery and installation; applications and uses for which this product was not intended; altered product or  
serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other  
acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories,  
applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG  
that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and  
surges; customer adjustments and failure to follow operating instructions, maintenance and environmental  
instructions that are covered and prescribed in the instruction book; product removal and reinstallation;  
problems caused by pest infestations.  
This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply,  
light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors.  
SAMSUNG does not warrant uninterrupted or error-free operation of the product.  
30_ Warranty  
DV337AEW-02453A-04_EN.indd 30  
2007-07-23 ¿ÀÈÄ 1:48:05  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS  
OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY  
IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR  
PURPOSE.  
NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT  
TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.  
SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE  
SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF  
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGES.  
NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE  
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.  
WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS,  
DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR  
PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT.  
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL  
PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.  
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation  
of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This  
warranty gives you specific rights, and you may also have other rights, which vary from state to state.  
To obtain warranty service, please contact SAMSUNG at:  
SAMSUNG ELECTRONICS AMERICA, INC. – CONSUMER ELECTRONICS CUSTOMER SERVICE  
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856  
1-800-SAMSUNG (1-800-726-7864)  
Warranty _31  
DV337AEW-02453A-04_EN.indd 31  
2007-07-23 ¿ÀÈÄ 1:48:05  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QUESTIONS OR COMMENTS?  
Country  
CALL  
1-800-SAMSUNG (7267864)  
OR VISIT US ONLINE AT  
U.S.A  
Code No. DC68-02453A-04_EN  
DV337AEW-02453A-04_EN.indd 32  
2007-07-23 ¿ÀÈÄ 1:48:05  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Stereo Amplifier 15 1119A User Guide
RCA Clothes Dryer BWXR473 User Guide
RCA IP Phone IP120 User Guide
Renesas Network Card HS7630KCM02HE User Guide
Roland Marine Safety Devices FR 3s 3 User Guide
Roland Speaker KCW 1 User Guide
Salter Housewares Stud Sensor IB 1015 0610 03 User Guide
Samson Speaker SAROD208A User Guide
Samson Thermostat 5100 User Guide
Samsung Air Conditioner SC18TB1 User Guide