Ryobi Saw 4060310 User Guide

OPERATOR'S MANUAL  
Miter Slot Table  
4060310  
(For use with BT3000 & BT3100 Table Saws)  
Your new miter slot table has been engineered and manufactured to Ryobi's high standard for dependability, ease  
of operation and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.  
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual.  
Thank you for buying a Ryobi accessory kit.  
SAVE THIS MANUAL FOR FUTURE REFERENCE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNPACKING  
INFORMATION  
WARNING:  
If any parts are missing, replace the missing parts  
before assembling the kit. Failure to do so could  
result in serious personal injury.  
Remove the loose parts from the box. Make sure  
that all items listed in the loose parts list are in-  
cluded .  
Inspect all parts carefully to make sure no breakage  
or damage occurred during shipping.  
LOOSE PARTS LIST  
1. Miter Slot Table  
If any parts are damaged or missing, please call  
1-800-525-2579 for assistance.  
2. Shims (4)  
3. 1/4-20 x 1 in. Hex Head Cap Screws (2)  
4. Washers (2)  
5. 1/4-20 Hex Nuts (2)  
MITER SLOT TABLE  
1/4-20 x 1 in.  
HEX CAP SCREW  
WASHER  
SHIM  
1/4-20 HEX NUT  
Fig. 1  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
TOOLS NEEDED  
7/16 in. NUT DRIVER  
3/16 in. HEX KEY  
Fig. 2  
ASSEMBLY  
INSTALLING THE MITER SLOT TABLE  
See Figure 3.  
WARNING:  
The table saw should never be connected to a power  
supply while you are assembling parts. Disconnect-  
ing the table saw will prevent accidental starting that  
could cause serious personal injury.  
Turn the ON/OFF switch to the OFF position.  
Unplug the saw from the switched on-board outlet.  
Disconnect the saw from the power supply.  
Remove the sliding miter table and accessory table  
from the saw.  
Place the miter slot table onto the saw as shown in  
Figure 3.  
1/4-20 x 1 in.  
HEX CAP SCREW  
MITER  
SLOT TABLE  
SHIMS  
WASHER  
1/4-20 NUT  
Fig. 3  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
REAR VIEW  
1/4-20 x 1 in.  
HEX CAP SCREW  
MITER  
SLOT TABLE  
PLACE SHIMS  
AS SHOWN  
SHIMS  
WASHER  
1/4-20 NUT  
FRONT VIEW  
Fig. 4  
ALIGNING THE MITER SLOT TABLE  
See Figure 4.  
MITER  
SLOT TABLE  
1/4-20 x 1 in.  
HEX CAP SCREW  
Place the miter slot table on the saw as shown in  
Figure 4.  
Extend a straight edge across the saw table onto  
the miter slot table and note any space between the  
straight edge and the miter slot table. If space ex-  
ists, place one of the shims under the miter slot  
table and recheck. Add shims as required between  
the miter slot table and the saw table to allow the  
miter slot table to be flush with or slightly lower than  
the saw table. Repeat the process for the rear of the  
miter slot table. Recheck in front and rear to assure  
that the miter slot table is not above the surface of  
the saw table.  
WASHER  
SHIM  
1/4-20 NUT  
Fig. 5  
Place mounting bolts with washers through holes in  
the miter slot table and the saw table frame as  
shown in Figure 5. Place a nut under the lip of the  
saw frame on each bolt. Tighten firmly and evenly.  
Shims will be secured when you tighten the screws.  
Replace the sliding miter table and the accessory  
table.  
NOTE: The miter slot table must not be higher than the  
saw table.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATOR'S MANUAL  
Miter Slot Table  
4060310  
WARRANTY  
Ryobi warrants its accessories for a period of 90 days from the date of purchase. Batteries and chargers are  
warranted for a period of two years from the date of purchase.  
PARTS AND SERVICE  
For parts or service, contact your nearest Ryobi authorized service center. Be sure to  
provide all relevant information when you call or visit. For the location of the authorized  
service center nearest you, please call 1-800-525-2579 or visit us online at  
MODEL NUMBER  
4060310  
RYOBI TECHNOLOGIES INC.  
1428 Pearman Dairy Road Anderson, SC 29625  
Post Office Box 1207  
1-800-525-2579  
Anderson, SC 29622  
972000-353  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q Logic Automobile Accessories APS 610 User Guide
Qualcomm Cordless Telephone GSP 1600 User Guide
Radio Shack Clock 63 974 User Guide
Radio Shack Handheld TV 16 173 User Guide
Raymarine GPS Receiver Ray54E User Guide
Ryobi Trimmer AC04141T User Guide
Samsung All in One Printer CLX4195FW User Guide
Sceptre Technologies Flat Panel Television X505BV FHD User Guide
Schumacher Battery Charger SE 1052 User Guide
Sears Automobile Battery Charger 608718571 User Guide