OPERATOR'S MANUAL
ROUTER MOUNTING KIT
4950301
(FOR USE WITH BT3000 AND BT3100 TABLE
SAWS)
Your new router mounting kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual.
Thank you for buying a Ryobi router mounting kit.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Safe operation of this accessory requires that you read and
■ KEEP FINGERS away from the cutter; use fixtures when
understandthisoperator'smanual,theoperator’smanualfor
the table saw and all labels affixed to the tool.
necessary.
■ ALWAYS USE THE DUST COVER for overhead guard-
ing.
READ ALL INSTRUCTIONS
■ DO NOT REMOVE JAMMED CUT OFF PIECES UNTIL
the switch is off, the cutter has stopped, and the tool has
been disconnected from the power source.
■ KNOWYOURACCESSORY.Readtheoperator'smanual
carefully. Learn the product's applications and limitations
as well as the specific potential hazards related to this
product.
■ HOLD WORKPIECE FIRMLY AGAINST THE TABLE.
■ UNUSED SAW MAY CAUSE PERSONAL INJURY. Dis-
connect the motor cord from the receptacle on your saw
and plug the router power cord into the receptacle.
Always use the saw's master switch to turn the router ON
and OFF.
■ KEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents. DO NOT leave tools
or pieces of wood on the saw while operating.
■ ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-resis-
tant lenses; they are NOT safety glasses.
■ NEVER USE A ROUTER BIT larger in diameter than the
opening in the router mounting plate.
■ DO NOT USE THIS PRODUCT WITH OTHER EQUIP-
■ DO NOT MAKE ADJUSTMENTS until the switch is off,
the cutter has come to a complete stop, and the tool has
been disconnected from the power source.
MENT OR FOR OTHER PURPOSES.
■ ALWAYSDISCONNECTTHESAWFROMTHEPOWER
SUPPLY BEFORE ASSEMBLING THIS KIT. Make sure
the switch is off when reconnecting the saw to a power
supply.
■ FEED WORKPIECE AGAINST ROTATION OF THE
CUTTER.
■ SAVETHESEINSTRUCTIONS.Refertothemfrequently
and use them to instruct other users. If you loan someone
this product, also loan these instructions.
■ BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
■ DO NOT USE AWKWARD HAND POSITIONS.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Thepurposeofsafetysymbolsistoattractyourattentiontopossibledangers. Thesafetysymbols, andtheexplanations
with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any
danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL: Indicates danger, warning or caution. May be used in conjunction with
other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION:Failure to obey a safety warning may result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal
injury.
NO HANDS: Failure to keep your hands away from the blade will result in serious personal injury.
WET CONDITIONS ALERT: Do not expose to rain or use in damp locations.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety
glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
WARNING:
WARNING:
Unplug the power supply cord of your saw from the
electrical outlet before you begin mounting this kit. It
should remain disconnected until the mounting
operation is complete, all attachments are installed
properly, and they have been checked to make sure
they are secure. Failure to unplug your saw could
result in accidental starting causing possible serious
personal injury.
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save this operator's
manualandreviewfrequentlyforcontinuingsafeoperation
and instructing others who may use this tool.
INTRODUCTION
This kit gives you the capability of mounting a router on
the accessory table of your saw. A router mounted on
the accessory table will provide expanded capabilities
for making rabbets, grooves, chamfers, dovetails, and
mortise and tenon joints.
INFORMATION
Remove the loose parts from the box. Make sure that all
items listed in the loose parts list and shown in Figure 1 on
page 6 are included.
■ Remove the loose parts from the box. Make sure that all
The additional versatility gained from use of this kit will
turn your table saw into a remarkable wood-shaping
center.
items listed in the loose parts list are included.
■ Inspect all parts carefully to make sure no breakage or
damage occurred during shipping.
NOTE:
■ If any parts are damaged or missing, please call
This router kit has been specifically designed for use
with Ryobi Routers Only. The hole pattern on the
mounting plate has not been drilled to accommodate
other routers.
1-800-525-2579 for assistance.
WARNING:
If any parts are missing do not assemble the kit until the
missing parts are replaced. Failure to do so could result
in serious personal injury.
WARNING:
Attempting to assemble the Router Mounting kit or
to use in any way without obtaining any missing
parts and installing them correctly, could result in
an accident resulting in possible serious injury.
TOOLS NEEDED
Tools needed for assembly of this kit are a phillips
screwdriver, two flat head screwdrivers, and an
adjustable wrench.
NOTE: The adjustable wrench will be used to tighten
the threaded post into one of the special 5/16 in. T-nuts
provided.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
THROAT PLATES
5/16 in.
WASHERS
GUIDE FENCE BRACKET
WITH GUIDE BLOCK
1/2 in. KNOB BOLTS
ROUTER
MOUNTING PLATE
TABLE
CLAMPING
BRACKET
3/4 in. KNOB BOLT
5/16 in. T-NUTS
POST
M8 SCREWS
5/16 in. WASHER
#10-32 SCREWS
SPACER
#5/16-18 SCREWS
GUARD/DUST COVER
WITH PIVOT ASSEMBLY
#1/4-20 SCREWS
Fig. 1
LIST OF LOOSE PARTS
Your #4950301 Router Mounting Kit includes the following parts:
DESCRIPTION
QUANTITY
DESCRIPTION
QUANTITY
Guide Fence Bracket with Guide Block .................. 2
Knob Bolt (5/16-18 x 1/2 in. for Guide Fence) ........ 4
5/16 in. Washer ....................................................... 5
5/16 in. T-Nut (Special) ........................................... 6
Spacer ..................................................................... 1
Post ......................................................................... 1
Guard/Dust Cover with Pivot Assembly .................. 1
Throat Plates ........................................................... 5
Router Mounting Plate ............................................ 1
Table Clamping Bracket .......................................... 1
Knob Bolt (#5/16-18 x 3/4 in. for Table Clamp) ...... 1
Screw (M8 x 24 mm flat head) ................................ 4
Screw (#10-32 x 1/2 in. flat head) ........................... 3
Screw (#5/16-18 x 3/4 in. flat head) ........................ 3
Screw (#1/4-20 x 1/2 in. flat head) .......................... 4
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
T-NUT SHOWN BETWEEN ADJUSTMENT SCREWS
WARNING:
The saw's motor cord must be disconnected from
the receptacle on the saw when using this kit. The
power cord of the router must be plugged into the
receptacle on the saw. The saw's master switch
must be used to turn the router ON and OFF.
Failure to do so could result in serious injury.
T-NUT
REAR ADJUSTMENT
SCREW
IMPORTANT
This router kit has been specifically designed for use
with Ryobi Routers. The hole pattern on the mounting
platehasnotbeendrilledtoaccommodateotherrouters.
NOTE: Mounting screws for Ryobi routers, model numbers
R160, R161, R165, RE170, RE170VS, R175, RE175, R180,
RE185, RE600, and RE601 are provided in this kit. Models
R175 and RE180PL must also use #4830175 depth control
kit, which is sold separately.
WASHER
TO INSTALL T-NUTS FOR GUIDE FENCE
BRACKETS:
See Figure 2.
This kit requires that five of the six special 5/16 in.
T-nuts provided fit in the top channel of the rip fence on
your table saw.
RIP FENCE SHOWN
LOCKED AGAINST SAW BLADE
■ Place miter fence against blade and lock in place.
Fig. 2
■ Using the appropriate allen wrench supplied with
your table saw, remove the rear adjustment screw
and washer on top of the rip fence.
INSTALL T-NUTS FROM REAR OF RIP FENCE
■ Slide one of the T-nuts into the top channel of rip
fenceandplacebetweenthetwoadjustmentscrews.
NOTE: T-nuts install from the rear of the rip fence.
T-NUT
■ Replace the washer and the rear adjustment screw
and tighten securely.
■ Check the rip fence for squareness with the saw
blade.
■ Unlock the rip fence, slide it away from the saw
blade, and lock it in place.
■ Slide the four remaining T-nuts into the top channel
of rip fence. See Figure 3.
NOTE:FiveT-nutsshouldbeinthetopchannelofthe
rip fence with only one of them between the
adjustment screws on the rip fence.
WOODEN INSERT
Fig. 3
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO INSTALL GUIDE FENCE BRACKETS:
GUARD/DUST COVER WITH
PIVOT ASSEMBLY
■ Toinstalltheguidefencebrackets,aligneachbracket
with two of the T-nuts on top of the rip fence.
See Figure 4.
CARRIAGE BOLT
(NOT SHOWN)
KNOB NUT
NOTE: Use the front two T-nuts and the back two
T-nuts leaving the one in the middle empty.
FLATS ON
POST
■ Secure the guide fence brackets to the rip fence with
5/16 in. washers and the 5/16 in. x 1/2 in. knob bolts.
KNOB
BOLTS
POST
TO INSTALL POST, GUARD/DUST COVER
WITH PIVOT ASSEMBLY:
■ Placethespaceronthethreadedendofthepostand
thread the post into the remaining T-nut.
See Figure 4.
5/16 in.
WASHERS
■ Tighten the post securely with an adjustable wrench
GUIDE FENCE
BRACKET
on the flats on the top of the post.
T-NUTS
SPACER
■ Place the guard/dust cover with pivot assembly on
the post. See Figure 4.
■ The assembly will slide up and down on the post as
needed. Secure at the desired location by tightening
the knob nut attached to the carriage bolt.
RIP FENCE
TO ASSEMBLE ROUTERS WITH 2-HOLE
PATTERN TO ROUTER MOUNTING PLATE:
See Figures 5 and 6.
Fig. 4
ROUTER WITH 2–HOLE PATTERN
For Ryobi routers, model numbers R175, RE175, and
RE180PL.
ROUTER
MOUNTING
SCREWS
ROUTER
MOUNTING
PLATE
NOTE: Models R175 and RE180PL must also use #4830175
depth control kit.
■ Unplug the router.
WARNING:
Unplug the router to avoid possible injury.
■ The black plastic subbase is glued to the router
base. Do not remove. Make sure the router switch is
OFF and the router is not connected to a power
source.
SUBBASE
■ Place the router upside down on a workbench and
align mounting holes of the mounting plate with the
two threaded holes in the router base.
ROUTER
BASE
■ The switch handle of the router should be facing the
squared end of the mounting plate.
See Figure 5.
Fig. 5
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO ASSEMBLE ROUTERS WITH 2-HOLE
2–HOLE ROUTER WITH MOUNTING PLATE ATTACHED
PATTERN TO ROUTER MOUNTING PLATE
(cont'd):
See Figures 5 and 6.
■ Secure the router mounting plate to the router using
two 5/16-18 x 3/4 in. bolts provided in the router
mounting kit. Tighten screws securely.
■ Properlyinstalled,themountingplatewillbesecurely
attached to the router.
See Figure 6.
TO ASSEMBLE ROUTERS WITH 3-HOLE
PATTERN TO ROUTER MOUNTING PLATE:
See Figures 7 and 8.
Fig. 6
ROUTER WITH 3–HOLE PATTERN
ROUTER
MOUNTING
PLATE
ROUTER
MOUNTING
SCREWS
For Ryobi routers, model numbers R160, R161, R165,
RE170, RE170VS, R180, and RE185.
■ Unplug the router.
WARNING:
Unplug the router to avoid possible injury.
■ Make sure the router switch is OFF and the router is
not connected to a power source.
ROUTER
BASE
■ Place the router upside down on a workbench and
remove the subbase screws and subbase from the
router.
FRONT
OF ROUTER
■ Align mounting holes of the mounting plate with the
three threaded holes in router base.
■ The switch handle of the router should be facing the
squared end of the mounting plate.
See Figure 7.
Fig. 7
3–HOLE ROUTER WITH MOUNTING PLATE ATTACHED
■ Secure the router mounting plate to the router using
three 5/16-18 x 3/4 in. bolts provided in the router
mounting kit. Tighten screws securely.
■ Properlyinstalled,themountingplatewillbesecurely
attached to the router.
See Figure 8.
Fig. 8
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO ASSEMBLE ROUTERS WITH 4-HOLE
PATTERN TO ROUTER MOUNTING PLATE:
ROUTER WITH 4–HOLE PATTERN
See Figures 9 and 10.
For Ryobi routers, model numbers RE600 and RE601.
ROUTER
MOUNTING
SCREWS
■ Unplug the router.
WARNING:
ROUTER
MOUNTING
PLATE
Unplug the router to avoid possible injury.
ROUTER
BASE
■ Make sure the router switch is OFF and the router is
not connected to a power source.
■ Place the router upside down on a workbench and
remove the subbase screws and subbase from the
router.
■ Align mounting holes of the mounting plate with the
four threaded holes in the router base.
■ The switch handle of the router should be facing the
squared end of the mounting plate.
See Figure 9.
FRONT
OF ROUTER
■ Secure the router mounting plate to the router using
four M8 flat head screws provided in the router
mounting kit. Tighten screws securely.
Fig. 9
4–HOLE ROUTER WITH MOUNTING PLATE ATTACHED
■ Properlyinstalled,themountingplatewillbesecurely
attached to the router.
See Figure 10.
NOTE: The clearance needed for mounting a router
to the table creates a gap between the accessory
table and the saw table. This gap must be filled with
a 22 in. wooden insert of appropriate width. This
insert should be 1-1/2 in. thick. Place this wooden
insert in the gap, level with the accessory table.
Assure that the insert does not interfere with the rip
fence. The rip fence should be positioned over the
accessory table and the wooden insert, as
appropriate. See Figures 2 and 3.
Fig. 10
WARNING:
Any gap between the tables resulting from the router
set up must be filled to reduce the risk of serious
injury.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTER MOUNTING
TO MOUNT ROUTER WITH PLATE TO
ACCESSORY TABLE:
THROAT PLATE
#1/4-20 SCREWS (PROVIDED)
ACCESSORY TABLE
■ Place the router with the mounting plate under the
accessory table. See Figure 11.
■ Secure the mounting plate to accessory table using
the four #1/4-20 x 1/2 in. flat head screws provided.
NOTE: The accessory table can be removed from
thetablesawtoattachtherouterandmountingplate.
Followinstructionsinthetablesawoperator'smanual
for removing and reattaching the accessory table.
■ Tighten screws securely.
SLOT
TOINSTALLROUTERBITANDTHROATPLATE:
■ Follow the instructions in the operator's manual of
your router for this procedure. Install router bit and
securely tighten in collet.
CAUTION:
Make sure the router bit will not strike the accessory
table or any metal surface.
ROUTER
WITH MOUNTING
PLATE ATTACHED
Fig.11
■ Select the correct size throat plate for the size of the
routerbit. Alignthetabonthethroatplatewiththeslot
in the accessory table and snap in place. Make sure
the throat plate is firmly seated below the table
surface. Rechecktherouterbittomakesureitwillnot
strike the throat plate.
TABLE CLAMPING BRACKET
SHOWN COMPLETELY ASSEMBLED
WARNING:
The router throat plates are included to assure no
more than 1/4 in. (6.4 mm) clearance between the
cutterandtheopeninginthethroatplate. Usecorrect
throat plate. Do not use a router bit smaller than 1/8
in. (3.2 mm) or larger than 2 in. (50 mm) in diameter.
ACCESSORY TABLE
TABLE
CLAMPING BRACKET
END PLUG
TO INSTALL TABLE CLAMPING BRACKET:
The lever on the accessory table will tighten the table
securely to the front rail. The weight of the router and
mountingplatemaycausetheaccessorytabletoloosen
orhavemovementattherearofthetable. Toavoidthis,
install the table clamping bracket supplied with this kit.
T-NUT
■ Remove end plug from rear rail as shown in
Figure 12.
REAR RAIL
■ Slide one of the T-nuts into the front channel of the
rear rail and under the accessory table.
5/16 in. WASHER
KNOB BOLT
■ The table clamping bracket fits in the bottom slot of
the rear rail. The slotted top of this bracket wraps
Fig.12
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTER MOUNTING
around the raised portion on the underside of the
accessory table, clamping it tightly against the rear
rail.
DIRECTION OF FEED IS FROM RIGHT TO LEFT
AGAINST SHARP EDGES OF ROTATING BIT
■ Secure with a 5/16 in. washer and 5/16-18 x 3/4 in.
knob bolt.
■ Tighten knob bolt securely.
FINAL ASSEMBLY:
After the router mounting parts have been assembled,
your setup should be similar to Figure 13.
■ Compare your setup and make any necessary
adjustments.
■ Recheck all knob bolts, attachments, etc., and
securely tighten.
ROUTER KIT SHOWN COMPLETELY ASSEMBLED
Fig. 13
OPERATION
FINAL PREPARATION FOR OPERATION
See Figure 13.
WARNING:
■ Adjust dust cover so that it will not come in contact
The direction of feed for the workpiece is always
against the sharp edges of the bit and into the
rotationofthecutter. Failuretoheedthiswarningcan
result in serious personal injury.
with workpiece during a cutting operation.
■ Direction of feed of workpiece is from right to left as
shown by the arrows in figure 13.
■ The workpiece must always be tight against the
guidefence, unlessaballbearingpilotedbitisbeing
used.Theinfeedfenceshouldbeadjustedtosupport
the uncut workpiece while the outfeed fence should
be adjusted to properly support the workpiece after
the cut passes the router bit, compensating for the
removed stock.
WARNING:
Do not use the guide fence with ball-bearing piloted
bits. Failuretoheedthiswarningcanresultinserious
personal injury.
WARNING:
The guard/dust cover must be used in all routing
operations. Do not attempt freehand use on
workpieces larger than 6 in. (15 cm) in diameter.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
4950301 ROUTER MOUNTING KIT
5
3
6
8
7
4
9
5
4
10
3
11
2
1
3
12
13
21
15
20
4
16
17
18
14
22
24
19
23
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
4950301 ROUTER MOUNTING KIT
Now that you have purchased your Router Mounting Kit, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when
you call or visit.
PARTS LIST
KEY PART
NO
NUMBER
DESCRIPTION
QUANTITY
1
2
969966-001
969965-002
969969-001
906382-361
661815-001
975424-003
975424-004
975424-005
975424-002
975424-006
969251-001
969961-003
661710-001
661815-002
982537-001
973605-001
622183-053
614661-001
969971-001
621433-017
969967-002
661816-001
969972-001
969968-002
983000-155
Guide Block...........................................................................................................2
Guide Fence..........................................................................................................2
Wood Screw (#10 x 5/8 in. round head) ...............................................................4
5/16 in. Washer .....................................................................................................5
Knob Bolt (#5/16-18 x 1/2 in.) ...............................................................................4
Throat Plate (1 in.) ................................................................................................1
Throat Plate (1-1/2 in.) ..........................................................................................1
Throat Plate (2 in.) ................................................................................................1
Throat Plate (1/2 in.) .............................................................................................1
Throat Plate (1-1/8 in.) ..........................................................................................1
5/16 in. T-Nut (Special) .........................................................................................6
Router Mounting Plate ..........................................................................................1
Table Clamping Bracket........................................................................................1
Knob Bolt (#5/16-18 x 3/4 in.) ...............................................................................1
Screw (M8 x 24 mm flat head) ..............................................................................4
Screw (#5/16-18 x 3/4 in. flat head)......................................................................3
Screw (#1/4-20 x 1/2 in. flat head)........................................................................4
Screw (#10-32 x 1/2 in. flat head).........................................................................3
Guard/Dust Cover with Decal ...............................................................................1
Carriage Bolt (#1/4-20 x 1-9/16 in.) ......................................................................1
Post .......................................................................................................................1
Knob Nut (#1/4-20 x 1-3/4 in. diameter) ...............................................................1
Dust Cover Pivot ...................................................................................................1
Spacer ...................................................................................................................1
Operator's Manual
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
#4950301 ROUTER MOUNTING KIT
(FOR USE WITH THE BT3000 AND BT3100 TABLE
SAWS
WARRANTY
Ryobi warrants its accessories for a period of 90 days from the date of purchase. Batteries and chargers are
warranted for a period of two years from the date of purchase.
PARTS AND SERVICE
For parts or service, contact your nearest Ryobi authorized service center. Be sure to provide all relevant information
when you call or visit. For the location of the authorized service center nearest you, please call
4950301
MODEL NUMBER
RYOBI TECHNOLOGIES INC.
1428 Pearman Dairy Road Anderson SC 29625
Post Office Box 1207 Anderson SC 29622-1207
Phone 1-800-525-2579
983000-155
Download from Www.Somanuals.com. All Manuals Search And Download.
|