INSTALLATION/OPERATION MANUAL
CX-47HD
CX-OPAL47
CX-65HD
1080p High-Definition LCD Flat Panel Displays
with
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare™ Standard Two Year Limited
Warranty
Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years
of unparalleled video performance.
This RuncoCare Standard Limited Warranty is provided free of charge by Runco International with the purchase of a covered
Runco product. The following sets forth Runco’s Standard Limited Warranty applicable to all Runco projectors, processors,
1
LCD and plasma display products, with the exception of the following models: XP-103DHD, SC-1, SC-1a and VW-100HD .
The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us, Runco
International and you, the customer who has purchased a Runco product. This contract applies to purchases of covered
Runco products occurring on or after September 1, 2008. Runco reserves the right to change the terms of this contract, and
such changes shall apply to purchases of covered Runco products that occur on or after any future effective date.
RuncoCare Standard Features
• Two-year protection from defects in material and workmanship
• Access to 24x7 phone support
• Complimentary, second-day one-way shipping
Warranty Coverage
Runco warrants its products to be free from defects in material and workmanship during the warranty period provided below.
If, in Runco’s determination, a product proves to be defective in material or workmanship during the warranty period, Runco
will repair the product, replace the product with a similar new or like new product, or refund a prorata share of the purchase
2
price (calculated based on the remainder of the warranty period and the then-current MSRP of a similar product), if repair or
replacement of the product is determined by Runco to not be feasible.
Length of Warranty
Runco products are warranted for two (2) years from the date of shipment from Runco. Lamps are warranted six (6) months
from the date of shipment or 1000 hours, whichever comes first. All other accessories, which includes, but is not limited to,
cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product, are warranted for ninety (90)
days from the date of shipment. Repaired product or replacement lamp is subsequently warranted for the remaining portion (if
any) of the original warranty term or 90 days from the date the product was shipped to you, whichever is longer.
Eligibility
This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an
authorized Runco dealer or distributor. This warranty is not transferable. You may be required to provide proof of purchase in
order to receive warranty services.
1. Runco may update this list of products excluded from this warranty from time to time at Runco’s sole discretion, but updates to
the list of covered products will not apply on a retroactive basis.
2. MSRP is defined as the most recent product price listed on Runco’s price list.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare Claim Procedure
In the event of a product defect, please follow the warranty claim procedure provided below:
1. The Customer is required to contact a Runco dealer or Runco Technical Support via email at [email protected] or via
in Europe for product service.
2. Be prepared to provide the date of purchase, the place of purchase, serial number, product model number, description of
the problem and troubleshooting steps already attempted.
3. Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem. If Runco is
unable to fix the problem to the customer’s satisfaction, Runco will issue a Return Material Authorization (RMA) if it is
determined that the claim was made within the coverage period of the Standard Limited Warranty.
4. The customer will need to return the defective product to the Runco repair depot location specified by the Runco technical
support representative. The customer will need to properly package the defective product, consisting of the product only,
and not include any accessories (e.g., cables, remotes, carrying cases, lens, lens cap and other peripherals) and return it
to the Runco repair depot specified by the technical support representative. It is the customer’s responsibility to properly
package the hardware, include all appropriate materials, and return it to the location specified by the Runco technical
support department. The customer will need to address and resolve any shipping damage claims directly with the shipping
company.
5. The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot.
Boxes may be purchased from a Runco technical support representative.
6. The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot.
7. Runco will pay freight charges to return the repaired/replacement product to the customer from the Runco repair depot.
8. Once an RMA has been created, the customer may contact [email protected] for followup questions or
confirmation status of the claim process.
Warranty Exclusions
This RuncoCare Standard Limited Warranty does not include or is limited by the following:
1. Products not purchased from an authorized Runco dealer
2. Rental costs incurred by the customer in the event of product defect or failure
3. Any product with a defaced, modified, or removed serial number
4. Damage, deterioration, or malfunction resulting from:
a Accident, abuse, misuse, neglect, improper ventilation, fire, water, disaster, lightning, or other acts of nature, smoke
exposure (cigarette or otherwise), unauthorized product modification (including use of an unauthorized mount), or failure
to follow instructions supplied with the product
b Repair or attempted repair by anyone not authorized by Runco
c Any damage to the product due to shipment
d Removal or installation of the product
e Causes external to the product, such as electric power fluctuations or failure
f Use of supplies or parts not meeting Runco’s specifications
g Normal wear and tear
h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed
i
Customer caused defects, including but not limited to, scratched/defaced/altered plastics
iv
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
j
Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for
regular cleaning of the product
k Opening the product and/or tampering with internal circuitry
Products lost, stolen or discarded
l
m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be
the result of customer use patterns
n Any other cause, which does not relate to a product defect in material or workmanship
5. Removal, installation, and setup service charges are excluded from this Standard Limited warranty
6. Runco’s warranty does not cover black uniformity issues or other LCD issues associated with usage outside the Runco
recommended guidelines and specifications for the product
7. Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver
to PO Box and FPO Box addresses
Extended Service Options
Runco offers extended and expanded service plans. For information on additional product protection, please email
[email protected] or call (toll free) 800-23RUNCO (800-237-8626).
Online Product Registration
Limitation of Implied Warranties
RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLIED, EXCEPT THOSE EXPRESSLY PROVIDED HEREIN. RUNCO
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Exclusion of Damages
RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT.
1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS,
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR
OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
2. RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR OTHERWISE.
3. RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of Local Law
This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities
do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the
above limitations and exclusions may not apply to you.
COPYRIGHT AND TRADEMARKS:
© Copyright 2008 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright,
trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of Runco.
The trademarks reporduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are
licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco.
Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents
Pending.
vi
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Thank you for your purchase of this quality Runco product! For best performance, please read this manual carefully as it is your
guide through the menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
11. Only use the attachments/accessories specified by Runco.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance Information
DECLARATION OF CONFORMITY:
Manufacturer’s Name: Runco International, LLC
Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992
hereby declares that the products Model Numbers:
CX-47HD, CX-OPAL47 and CX-65HD
conform with the provisions of:
Council Directive 2004/108/EC on Electromagnetic Compatibility;
EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment”
1998;
EN 55024 “Limits and methods of measurements of immunity characteristics of information technology equipment” 1998;
Including:
• EN 61000-4-2 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2:
Electrostatic discharge immunity test”
• EN 61000-4-3 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated,
Radio-Frequency, Electromagnetic Field Immunity Test”
• EN 61000-4-4 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 4: Electrical
fast transient/burst immunity test”
• EN 61000-4-5 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 5: Surge
immunity test"
• EN 61000-4-6 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 6: Conducted
disturbances induced by radio-frequency fields immunity test"
• EN 61000-4-8 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 8: Conducted
disturbances induced by power frequency magnetic fields immunity test"
• EN 61000-4-11 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 11: Voltage
dips, short interruptions and voltage variations immunity tests"
And:
• EN 61000-3-2 "Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment
input current up to and including 16 A per phase)" 2000;
• EN 61000-3-3 "Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage
fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A
and not subject to conditional connection" 1995;
Council Directive 2006/95/EC and amended by M1 and C1 on Low Voltage Equipment Safety;
EN 60950 “Safety of information technology equipment, including electrical business equipment”
The Technical Construction file required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc.,
1195 NW Compton Drive, Beaverton, OR 97006.
Date of Declaration: January 2009
viii
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC PART 15:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA (ICES-003):
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IMPORTANT RECYCLE INSTRUCTIONS
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be
hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws.
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European
Union and other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not be treated as
household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences to the environment and human health, which could
otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve
natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please
contact your local authorities or dealer and ask for the correct method of disposal.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
x
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
RuncoCare™ Standard Two Year Limited Warranty ...................................................iii
Important Safety Instructions ....................................................................................... vii
Compliance Information .............................................................................................. viii
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
If You Have Comments About This Manual.............................................................1
2. Controls and Functions ............................................................................................5
Crystal Series LCD at a Glance ....................................................................................5
3. Installation ...............................................................................................................13
Notes on Remote Control Operation.....................................................................13
Quick Setup ...............................................................................................................14
Other Considerations............................................................................................15
RS-232 Controller Connection..............................................................................21
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation .................................................................................................................23
Using the On-Screen Menus ......................................................................................25
ISF Calibration .....................................................................................................38
Using Picture-In-Picture (PIP) .....................................................................................41
5. Maintenance and Troubleshooting ........................................................................45
6. Serial Communications ..........................................................................................47
RS-232 Connection and Port Configuration ...............................................................47
7. Specifications ..........................................................................................................53
Crystal Series LCD Dimensions ..................................................................................55
xii
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
2-3. Model CX-65HD Inputs and Outputs............................................................................8
3-1. HDMI Connections.....................................................................................................16
3-5. SCART RGB Connections..........................................................................................19
4-1. Crystal Series LCD OSD Menu Structure....................................................................26
4-3. Typical Gray Bar Pattern for Adjusting Contrast..........................................................30
7-3. CX-65HD Overall Dimensions (Top/Front)...................................................................57
7-4. CX-65HD Overall Dimensions (Rear/Side)...................................................................58
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Notes:
xiv
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This Owner’s Manual describes how to install, set up and operate the Runco Crystal
Series Model CX-47HD, CX-OPAL47 and CX-65HD Flat-Panel LCDs. Throughout this
manual, the Runco CX-47HD, CX-OPAL47 and CX-65HD Flat-Panel LCDs are referred to
collectively as the “Crystal Series LCD.” The information in this manual applies to all three
products, except where otherwise indicated.
1.1
About This Manual
Runco has prepared this manual to help home theater installers and end users get the
most out of the Crystal Series LCD.
Target Audience
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
If You Have Comments
About This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Textual and Graphic
Conventions
• Remote control button identifiers are set in upper-case bold type; for example, “Press
EXIT to return to the previous menu.”
• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Letterbox, type [S4E0002.”
• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc>
and <Tab>.
• <Enter> indicates that you may press either the RETURN or ENTER key on your
computer keyboard if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
A carriage return must be used after each command or string.
Note
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or
death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
... Turn to page:
Information about obtaining service
General information about the CX-47HD,
CX-OPAL47 and CX-65HD Flat-Panel LCDs
Installation instructions
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Specifications for the CX-47HD, CX-OPAL47 and
CX-65HD Flat-Panel LCDs
2
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Runco presents the Crystal Series CX-47HD, CX-OPAL47 and CX-65HD Flat-Panel
LCDs, perfect for those who demand our award-winning flat-panel performance along
with advanced LCD technology and lightweight design.
1.3
Description, Features
and Benefits
The Crystal Series LCD incorporates the superb Vivix™ digital video processing that
produces outstanding picture quality with a wide range of both standard and high
definition source material. In addition, the handsome, anodized black-finish television is
engineered with ISF™ calibration standards for the purest video performance.
The Crystal Series LCD offers Picture-In-Picture (PIP), Picture-By-Picture (PBP) and
multi-language support. The display includes an integrated stereo audio system with
generous power amplification.
The advanced, TFT active-matrix liquid crystal display panel offers 1920 x 1080 resolution
and includes Runco’s discrete aspect ratio control with VirtualWide™ mode to fill the 16:9
screen with standard 4:3 images without loss of picture quality. Also included are discrete
source, aspect ratio and power selection and an RS-232 interface for whole-house or
automated control system integration.
The Crystal Series LCD is multimedia ready, with simple computer connections making
gaming, Internet browsing and other computing activities quick and easy.
The Crystal Series LCD offers these key features and benefits:
• Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)
• Real-Time Refresh (RTR) technology supports 120-Hz frame rates
Key Features and Benefits
• Model CX-OPAL47 features Runco-exclusive Optical Path Alignment (OPAL)
technology, which delivers extreme glare reduction and enhanced contrast for high
ambient light environments
• Multiple aspect ratios with VirtualWide™ Mode
• Less than 6-3/4 inches deep
• Four (4) HDMI 1.3a Inputs with High-bandwidth Digital Content Protection (HDCP)
• Exceptional detail and artifact-free video enhancement
• Runco video processing with 3:2 film detection circuitry
Your Crystal Series LCD is shipped with the following items. If any items are missing or
damaged, please contact your Runco dealer or Runco Customer Service at (800)
23-RUNCO.
Parts List
• Crystal Series LCD Panel with Table Stand: Model CX-47HD (part number
997-5581-00), CX-OPAL47 (part number 997-5599-00) or CX-65HD (part number
997-5582-00)
• Remote Control Unit and two (2), AAA-size batteries
• AC Power Cord
• CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual (this document)
Optional Accessories:
• Wall Mount Kit – part number 956-0093-00 (CX-47HD/CX-OPAL47) or 956-0285-00
(CX-65HD)
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
4
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Controls and Functions
2.1
Crystal Series LCD at a
Glance
Figure 2-1 shows the locations of the Crystal Series LCD controls and indicators.
Controls and Indicators
CX-47HD / CX-OPAL47
1
2
1
SOURCE
MENU/EXIT
3
4
5
6
CX-65HD
1
1
1
SOURCE
2
1
MENU/EXIT
3
4
5
6
Figure 2-1. Crystal Series LCD Controls and Indicators
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. HANDLES
Always use the handles when carrying the display. DO NOT touch or hold the
screen face.
2. MAIN POWER SWITCH
Connects or disconnects the display panel from the AC power source.
3. DISPLAY STAND
Included with the Crystal Series LCD for table-top installations.
4. FRONT REMOTE CONTROL SENSOR
REAR REMOTE CONTROL SENSOR (not shown)
The Crystal Series LCD is equipped with two infrared (IR) sensors that receive signals
from the remote control unit. The rear sensor is directly opposite the front sensor, on
the back of the unit. It allows an IR “bug” to be attached to the rear of the panel
(eliminating the need to wrap the wire around the frame) for a cleaner look.
5. STATUS LED
Lights orange to indicate that the Crystal Series LCD is in standby mode; Off during
normal operation or if the main power switch is set to off.
6. KEYPAD
You can use the keypad instead of the remote control unit to
operate the on-screen display (OSD) controls. The keypad
operates as follows:
On/Standby (
)
Press once to toggle from standby mode to on mode. Press it
again to return to standby mode. For a discrete on or off
command, you can use the direct access buttons on the
remote control unit (refer to Crystal Series LCD Remote
SOURCE
SOURCE
To select a source, press the SOURCE button repeatedly (with
no menus visible on-screen).
(Volume +)
Use this button to increase the sound volume. When a menu is
visible on-screen, this button operates identically to the
right-arrow (or ENTER) button on the Crystal Series LCD
remote control unit.
(Volume -)
Use this button to decrease the sound volume. When a menu
is visible on-screen, this button operates identically to the
left-arrow button on the Crystal Series LCD remote control unit.
MENU/EXIT
/
When a menu is visible on-screen, these buttons operate
identically to the up- and down-arrow buttons on the Crystal
Series LCD remote control unit.
MENU/EXIT
Press this button to access the on-screen display (OSD) controls, or to exit the
current menu and return to the previous one.
6
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. AC Power Input (100 to 240 VAC)
Connect the Crystal Series LCD to power here.
2. RS-232 CONTROL PORT
A female, 9-pin D-sub connector for interfacing with a PC or home theater
automation/control system.
3. VIDEO 1/SCART Sync Input (Composite Video + Stereo Audio)
Standard, composite video input and stereo audio input for connecting a VCR,
camcorder, laser disc player or other composite video source. The Composite video
input also provides composite sync input for SCART RGBS sources.
4. VIDEO 2 Input (Composite or S-Video + Stereo Audio)
Standard, composite or S-video input and stereo audio input for connecting a VCR,
camcorder, laser disc player, Super VHS (S-VHS) VCR or other composite or S-video
source.
If both the Composite and S-Video inputs on Video 2 are connected
to sources, the S-Video input takes precedence.
Note
5. COMPONENT 1/SCART RGB (Component or SCART RGB Video + Stereo
Audio)
Standard- or high-definition (up to 1080p), YPrPb component video and stereo audio
input. Also provides RGB input for RGBS sources.
6. COMPONENT 2 (Component Video + Stereo Audio)
Standard- or high-definition (up to 1080p), YPrPb component video and stereo audio
input.
7. IR IN
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system.
8. DIGITAL AUDIO OUT (S/PDIF Optical)
®
Connect this output to the digital audio input of an A/V amplifier with a Dolby Digital
decoder.
9. HDMI1 / HDMI2 / HDMI 3 / HDMI 4
Four, HDCP-compliant digital video inputs for connecting a DVD player, personal
computer or HD tuner with a DVI or HDMI output.
10. RGB
A 15-pin VGA connection to a personal computer. The Crystal Series LCD
automatically detects the signal resolution.
11. PC Audio Input
Connect the audio output from a personal computer here.
12. SPEAKER OUTPUT (LEFT + RIGHT)
For connecting external speakers with an impedance of 4 ohms.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-4 shows the Crystal Series LCD remote control, and the paragraphs that follow
describe its functionality.
2.2
Crystal Series LCD
Remote Control
2
RGB
1
4
3
HDMI 1
HDMI 2
HDMI 3
VID 1
HDMI 4
VID 2
COMP 1 COMP 2
1
4
2
5
8
0
3
6
+
BRIGHT
5
7
–
6
8
7
9
+
CONTR
100
MUTE
–
CUSTOM
ENTER
MENU
VOL-
VOL+
9
10
TIMER
OFF
11
16:9
PIP
4:3
LETTER V WIDE
12
14
POSITION
SIZE
SWAP
13
15
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
Figure 2-4. Crystal Series LCD Remote Control
10
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. ON
Use this button to turn the Crystal Series LCD on.
2. RGB HD
Press this button to switch to the RGB HD input.
3. STANDBY
Use this button to put the Crystal Series LCD into standby mode.
4. Source Selection Buttons
HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4
Use these buttons to select a Digital Video input (HDMI 1, HDMI 2, HDMI 3 or
HDMI 4).
COMP 1 / COMP 2
Press this button to select a Component Video input.
VIDEO 1 (Composite) / VIDEO 2 (Composite or S-Video)
Press this button to select a Composite or S-Video input.
5. BRIGHT + / BRIGHT -
Use these buttons to adjust the brightness.
6. Numeric Buttons / MUTE Button
Use the numeric buttons to enter menu pass codes. Press the MUTE button to mute
the audio output to the speakers.
7. CONTR + / CONTR -
Use these buttons to adjust the contrast.
8. Memory Preset Buttons
ISF DAY
Press to recall settings for the current input from the “ISF Day” memory preset.
CUSTOM
Press to recall settings for the current input from the “Custom” memory preset.
ISF NIGHT
Press to recall settings for the current input from the “ISF Night” memory preset.
9. Arrow Buttons ( ,
,
,
)
Use these buttons to select items or settings, adjust settings or adjust sound volume.
ENTER
Press to select a highlighted menu item or confirm a changed setting.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10. EXIT
Press this button to hide the OSD controls.
MENU
Press this button to access the on-screen display (OSD) controls, or to exit the
current menu and return to the previous one.
INFO
Press this button to view input signal information (source and resolution), audio format
(mono or stereo) and current time.
11. TIMER OFF Button
Press this button to set the sleep timer.
12. Aspect Ratio Selection Buttons
16:9
For 16:9 DVDs or HDTV program material.
4:3
The input signal is scaled to fit 4:3 display mode in the center of the screen.
LETTER (Letterbox/Cinema Fill)
Image in letterbox format is enlarged to fit 16:9, full-screen display and the
upper/lower portions are “blanked off.”
V WIDE (VirtualWide)
4:3 image is enlarged NON-linearly in horizontal direction to fit 16:9 full screen display.
13. Picture-In-Picture (PIP) Function Buttons
PIP
Press to change the PIP mode (picture-in-picture, picture-by-picture or off).
POSITION
Press to choose the PIP window position (top left, top right, bottom left or bottom
right corner).
SIZE
Press to choose from three PIP window sizes.
SWAP
Press to swap the main and PIP windows.
14. PIP SRC
Press to switch to a different PIP video source.
15. AUDIO 1 / AUDIO 2 / AUDIO 3
Use these buttons to select an audio “mode” (volume and equalizer preset). For more
12
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
3.1
Remote Control
To install batteries in the remote control:
Battery Installation
1. Slide the battery cover in the direction of the arrow and remove it.
2. Insert the included batteries. Ensure that the polarities correctly match the
markings inside the battery compartment.
and
3. Slide the battery cover back on until it snaps into place.
1. Do not mix an old battery with a new one or different types of
batteries.
Note
2. If you will not use the remote control for a long time, remove the
batteries to avoid damage from battery leakage.
• Do not drop the remote control or expose it to moisture or high temperature.
Notes on Remote Control
Operation
• The remote control may malfunction under a fluorescent lamp. If that occurs, move the
LCD display away from the fluorescent lamp.
• Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the LCD display.
The signal from the remote control can be reflected by walls or
other surfaces.
Note
• If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
• Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the LCD display and repeat the operation.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 gives a quick overview of the Crystal Series LCD installation process. The
sections following this one provide detailed instructions.
3.2
Quick Setup
Installation should be performed by a qualified custom video
installation specialist.
Note
Table 3-1. Installation Overview
For Details, refer to
Step
Procedure
page...
Mount the Crystal Series LCD on a wall (optional)
Connect signal sources to the Crystal Series LCD
Connect external controller to RS-232 port (optional)
Apply power to the Crystal Series LCD
1
2
3
4
5
Change the OSD language
If using the Crystal Series LCD with a PC, adjust PC display
properties
6
Display calibration: adjust the following for each input;
save settings when finished:
• Brightness
• Contrast
7
• Color level
• Tint
• Input position
14
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your Crystal Series LCD will ensure the highest possible picture
quality. Whether you are installing the Crystal Series LCD temporarily or permanently, you
should take the following into account to ensure that it performs optimally.
3.3
Installation
Considerations
You can either place the Crystal Series LCD on a table or in an entertainment center, or
mount it on a wall.
Wall-Mounting the Crystal
Series LCD
If you do decide to wall-mount the Crystal Series LCD, ensure that the wall-mount bracket
is installed according to the instructions included with it. The wall must be capable of
supporting a redundant weight factor three (3) times the weight of the display, or be
reinforced.
Runco recommends that this be done by a custom installation specialist.
Use only the Runco-approved wall-mount kit designed for your
display.
Note
In general, minimize or eliminate light sources directed at the display. Contrast ratio in your
images will be noticeably reduced if light directly strikes the display, such as when a shaft
of light from a window or floodlight falls on the image. Images may then appear washed
out and less vibrant.
Ambient Light
Other considerations and tips that can help improve your installation:
Other Considerations
• Keep the ambient temperature constant and below 35°C (95°F). Keep the display away
from heating and/or air conditioning vents. Changes in temperature may cause drifts in
the display circuitry, which may affect performance.
• Keep the Crystal Series LCD away from devices that radiate electromagnetic energy
such as motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
Proceed as follows to connect the Crystal Series LCD to your video sources, external
controller(s) – if present – and AC power.
3.4
Connections to the
Crystal Series LCD
When connecting your equipment:
• Turn off all equipment before making any connections.
• Use the correct signal cables for each source.
• Ensure that the cables are securely connected. Tighten the thumbscrews on
connectors that have them.
• Use the left audio input when connecting mono audio sources.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Crystal
Series LCD to Source
Components
Connect your video sources to the Crystal Series LCD as shown and described in the
sections that follow.
➤
HDMI Connections: The Crystal Series LCD has four HDMI inputs for connecting a
BD/HD-DVD/DVD player, DTV decoder, personal computer or any other device with an
Use the HDMI inputs whenever possible. This ensures the highest
Tip
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
into the display.
This Crystal Series LCD supports the VESA Display Data Channel
(DDC) standard. This standard provides “Plug and Play” capability;
the display and a VESA DDC-compatible computer communicate
their setting requirements, allowing for quick and easy setup.
Note
In order for Plug and Play to work correctly, you must turn on the
display before you turn on the connected computer.
Rear of the PC
Audio Cable
(Sold Separately)
DVI-to-HDMI Cable
(sold separately)
HDMI or
DVI-to-HDMI Cable
(sold separately)
BD/HD-DVD/
DVD/DTV STB
Figure 3-1. HDMI Connections
16
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB Connections: The Crystal Series LCD has an RGB input and a stereo audio input
Rear of the PC
Audio Cable
(Sold Separately)
D-Sub 15-pin Cable
(sold separately)
Figure 3-2. Analog RGB Connections
signals compatible with the Crystal Series LCD. Use with signals
Note
other than those listed may cause some functions not to work.
2. Some Macintosh computers may require a Macintosh video
adapter. Contact your nearest authorized service center or dealer.
3. This Crystal Series LCD may not be able to display images from
notebook computers in simultaneous (CRT/LCD) mode. Should
this occur, switch the notebook computer to “CRT only” mode. If
you are unsure how to do this, refer to your notebook computer’s
user manual.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Video Connections: If you have a DVD player, DTV decoder with a
component (YPbPr) output or other component video source, connect it to the
Video Cable
DVD/DTV STB
Audio Cable
Figure 3-3. Component Video Connections
Composite/S-Video Connections: The Crystal Series LCD has two (2) Composite
video inputs and an S-Video input for connecting a VCR, camcorder, laser disc player or
If you connect an S-Video source to the Video 2 input, the
Composite input on Video 2 is inactive.
Note
S-Video Cable
VCR
Composite Video Cable
Audio Cable
Camcorder
Gaming Console
Figure 3-4. Composite and S-Video Connections
18
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SCART Video Connections: Connect the green, blue and red outputs from your SCART
source to the Component 1 input on the Crystal Series LCD. Connect the sync output
Note
VCR
SCART-RGBS
Adapter
Green
Blue
Green
Blue
DVD/DTV STB
Red
Red
Sync
Gaming Console
Sync
Figure 3-5. SCART RGB Connections
Connect the
(positive) and
(negative) speaker wires to the SPEAKER-R and
Connecting External
Speakers (Optional)
information, refer to the owner’s manual for your speakers.
Left Speaker
12 mm
Twist exposed
wire strands
together.
Push tab to the
open position, and
insert the wire.
Right Speaker
Then, close tab firmly to
secure the wire in place.
Figure 3-6. External Speaker Connection
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Dolby
If your home theater has a Dolby Digital amplifier or receiver, connect the SPDIF digital
audio output from the Crystal Series LCD to the digital audio input of the amplifier/receiver
➤
Digital Amplifier
The audio output level is fixed. (The volume and mute controls affect
only the speaker outputs.)
Note
Digital Audio Cable,
Optical
Dolby Digital
Amplifier
Figure 3-7. Digital Audio Connection
20
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
If infrared signals from the remote control cannot reach the display due to excessive
distance or obstructions such as walls or cabinet doors, you can connect an external IR
repeater system to the IR INPUT on the Crystal Series LCD to extend the range of the
Connecting an External IR
Receiver
Remote Control
IR Sensor
IR Repeater
(3.5-mm, mini
phono plug)
Figure 3-8. External IR Receiver Connection
Use a straight-through RS-232 cable with a 9-pin male connector to connect a PC or
home theater control/automation system (if present) to the RS-232 port on the Crystal
RS-232 Controller
Connection
Connector Pin Assignments:
DB-9 Male
2
3
5
Receive Data
Transmit Data
Ground
To PC or
Automation/
Control
1, 4, 6, 7, 8, 9
Not Connected
System
Figure 3-9. RS-232 Control System Connection
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
22
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation
1. Turn on your source components.
4.1
Turning on the Power
2. Plug the female end of the supplied power cord into the AC receptacle on the side of
Figure 2-3 (CX-65HD).
3. Connect the other end to your AC power source.
4. Turn on the main power switch at the side of the display. The power indicator lights
orange to indicate that the Crystal Series LCD is in “standby” mode.
5. Press the ON button (
control to turn on the display (or press the
power button ( ) on the side of the display).
) on the remote
RGB
The power indicator turns off.
6. After a brief warm-up period (approximately 10
seconds), the Crystal Series LCD will display
an image.
HDMI 1
HDMI 2
HDMI 3
VID 1
HDMI 4
VID 2
COMP 1 COMP 2
The Crystal Series LCD OSD language is initially set to English, but can also display the
menus in French, Spanish, Portuguese or German. To change the OSD language:
4.2
Changing the OSD
Language
1. Press MENU.
2. Select Setup from the Main Menu.
3. Select OSD Language from the Setup Menu.
4. Press or to highlight the desired language and press ENTER. The change takes
effect immediately.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
To maximize image quality when using the Crystal Series LCD with a personal computer,
you may need to adjust the display properties of your PC video card. To do this:
4.3
Setting the PC Display
Properties
1. Choose Settings from the Windows Start
menu and click on “Control Panel.”
2. Double click on the Display icon.
3. Click the Settings tab on the display
dialog box.
4. Set the Screen area to 1400x1050 pixels.
5. Click the Advanced button and click the
Monitor tab on the dialog box. Set the
Refresh Frequency to 60Hz and click OK.
24
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. The maximum available resolution and vertical frequency is
1920x1200/60Hz or the maximum supported by your video
card, whichever is lower.
Note
2. The Crystal Series LCD supports 30-bit color (1,073,741,824
possible colors).
To use the on-screen menus:
4.4
Using the On-Screen
Menus
1. Press MENU to display the Main Menu.
2. To select a menu item, use the up- or down-arrow buttons (
control to highlight it.
,
) on the remote
3. Press ENTER or the right-arrow button ( ) to access that menu.
4. Use the up- or down-arrow buttons ( ) to select the setting you want to change.
Then, press ENTER or the right-arrow button ( ).
5. Press the right- or left-arrow button ( ) to change that setting.
6. To return to the previous menu, press MENU or ( ).
,
,
Depending on the selected input source and/or signal characteristics, some menu options
may not be available.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI 1
English, Français,
Español, Português or
Deutsch
OSD Language
OSD Timer
HDMI 2
HDMI 3
0, 10, 20 ... 60 sec.
Auto Adjust
Clock
HDMI 4
Component 1/SCART
Component 2
RGB
Note: If SCART is
enabled in the Setup
menu, Component 1
and Video 1 are
disabled.
Source
Phase
PC Mode Adjust
H. Position
V. Position
Factory Reset
Video 1/SCART
Video 2
16:9
Overscan
(not available with PC
signals)
H. Overscan, H. Shift,
V. Overscan, V. Shift
4:3
0, 1, 2, 3 ... 10
Aspect Ratio
Letterbox/Cinema Fill
VirtualWide
Brightness
Contrast
Color
Letterbox or
Cinema Fill
Letterbox Mode
HDMI or
Stereo (PC Audio In)
HDMI Audio Input
HDMI 1 ... HDMI 4
0, 1, 2, 3 ... 100
Setup
Film Mode
Off, 2:3, 2:2 or Auto
Off / On
Tint
Auto Backlight
Sharpness
DNR
0, 1, 2, 3 ... 24
0, 1, 2, 3 ... 5
0, 1, 2, 3 ... 63
0, 1, 2, 3 ... 100
Automatic, RGB or
Component
HDMI CSC
HDMI 1 ... HDMI 4
MPEG NR
Backlight
115200, 19200, 9600
or 2400
Picture Adjust
Baud Rate
SCART
5400, 6500, 8500 or
Custom
Off / On
Color Temp.
HDMI 1 ... HDMI 4
Component 1
Component 2
RGB
Video 1
Video 2
Gamma
2.0, 2.2 or 2.4
Custom
Save Settings
Source Enable
Enable / Disable
Custom, ISF Day,
ISF Night
Restore Settings
Balance
0 (L), 1, 2 ... 10 (C) ... 18,
19, 20 (R)
LED Option
System Info
Off / On
Model Number/
Serial Number/
Firmware Version
(read-only)
Custom 1, Custom 2 or
Custom 3
Audio
Timer
Equalizer
Speaker
Time
(On/Off)
12:00 AM - 11:59 PM
Brightness
Contrast
Color
Enable/Disable, Time,
Input, Volume
On Timer
Off Timer
Sleep Timer
0, 1, 2, 3 ... 100
Enable/Disable, Time
Tint
Off, 10, 30, 60, 120 or
180 minutes
Sharpness
ADC Phase Adj.
DNR
0, 1, 2, 3 ... 24
0, 1, 2, 3 ... 63
0, 1, 2, 3 ... 5
0, 1, 2, 3 ... 63
0, 1, 2, 3 ... 100
MPEG NR
Backlight
Picture Adjust
5400, 6500, 8500 or
Custom
Color Temp.
Gamma
ISF Calibration
2.0, 2.2 or 2.4
Custom, ISF Day, ISF
Night
Save Settings
Custom, ISF Day,
ISF Night
Restore Settings
R/G/B Gain
128, 129 ... 256 ... 383,
384
White Balance
R/G/B Offset
-50, -49 ... 0 ... 49, 50
Blue Enable
(Enable/Disable)
(No/Yes)
Factory Reset
Splash Duration
0, 5, 10, ... 60 secs.
Figure 4-1. Crystal Series LCD OSD Menu Structure
26
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The Main Menu is the starting point for accessing all Crystal Series LCD functions.
(The ISF Calibration menu is not accessible until you enter a passcode.)
Main Menu
Runco CX-65HD
Source
Aspect Ratio
Picture Adjust
Audio
Timer
Setup
ISF Calibration
From the Main Menu, select Source to choose a video signal source.
Source
The active source is indicated by an arrow (>) to its left; in this example, HDMI 1 is the
active source.
>
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Component 1
Component 2
RGB
Video 1
Video 2
To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio
from the Main Menu and press ENTER. Select the appropriate aspect ratio for the type of
Aspect Ratio
>
16:9
4:3
The currently-selected aspect ratio is indicated by an arrow (>) to its left; in this example,
16:9 is selected.
Letterbox
VirtualWide
The aspect ratio selection persists until you change it. (It is not
saved independently for each input.)
Note
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Remote
Aspect Ratio
Control
Key
Description
16:9
16:9
Select 16:9 to view 16:9
DVDs and HDTV programs
in their native aspect ratio.
16:9 Image on
16:9 Screen (Display)
4:3 images are stretched
horizontally to fit a 16:9
display.
4:3 Image, stretched to fill
16:9 Screen (Display)
4:3
4:3
4:3 scales the input signal to
fit in the center of a 16:9
display. 4:3 is the aspect
ratio used by computer
monitors, standard
4:3 Image on
16:9 Screen (Display)
television programming and
most VHS video cassettes.
Letterbox/
Cinema Fill
LETTER
Letterbox mode scales
(zooms in on) a 4:3 image
linearly (by the same amount
on all sides) to fill a 16:9
display.
Letterbox Mode = Letterbox
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
The zoom factor is either
1.33 or 1.78, depending on
(refer to Letterbox Mode
Letterbox Mode = Cinema Fill
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
Letterbox is best suited for
viewing LaserDisc movies or
non-anamorphic DVDs on a
16:9 screen.
28
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Remote
Aspect Ratio
Control
Key
Description
VirtualWide
V WIDE
VirtualWide scales a 4:3
image NON-linearly (more
on the sides than in the
center) to fit a 16:9 screen.
4:3 Image on
16:9 Screen (Display)
4:3 Image on
16:9 Display
with VirtualWide
Use the controls in the Picture Adjust menu to calibrate your Crystal Series LCD for
optimum picture quality.
Picture Adjust
Picture Adjust
Brightness
The Crystal Series LCD has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards to
obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF-certified installation
technician.
Contrast
Color
Tint
Sharpness
DNR
All signal types require separate processing. Therefore, you need to calibrate each input
separately.
MPEG NR
Backlight
Color Temp.
Gamma
When you change a picture quality setting, save the change to a
Note
preset afterwards. Otherwise, the change will be lost when a
different input is selected. (Picture quality settings are saved for
each input and resolution separately.) For information about saving
Save Settings
Restore Settings
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Runco recommends using the following calibration tools for best
results:
• External test pattern source – Ovation Multimedia, Digital Video Essentials or AVIA test
DVD or equivalent.
• A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input that you are calibrating and proceed as
follows. Perform the adjustments in the order listed here.
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an
pattern.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Below Black
Above Black
Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
Select Brightness from the Picture Adjust menu. Using the left- and right-arrow (
buttons, adjust the brightness so that:
)
• The darkest black bars disappear into the background.
• The dark gray areas are barely visible.
• The lighter gray areas are clearly visible.
• The white areas are a comfortable level of true white.
• The image contains only black, gray and white (no color).
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast from the Picture Adjust menu. Using the left- and right-arrow (
buttons, adjust the contrast to a point just below which the white rectangle starts to
increase in size.
)
30
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Brightness and contrast controls are interactive. A change to one
may require a subtle change to the other in order to achieve the
optimum setting.
Note
Color Saturation: On your external test pattern source, select a color bar pattern like the
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
Select Color from the Picture Adjust menu. While looking at the color bar pattern through
a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars
appear to be a single shade of blue:
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image
appears greener. To set the tint, select Tint from the Picture Adjust menu. While looking at
the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta
color bars (on either side of the green bar) appear to be a single shade of blue.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Like the brightness and contrast controls, the color and tint controls
are interactive. A change to one may require a subtle change to the
other in order to achieve the optimum setting.
Note
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust
sharpness, select Sharpness from the Picture Adjust menu and press ENTER. On your
needed, looking for white edges around the transitions from black to gray and different
sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to
eliminate them.
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
Picture Adjust menu. Noise reduction is useful for clearing up noisy RGB images such as
those from a PC. Adjust as desired using the left- or right-arrow buttons, keeping in mind
that reducing noise (which reduces high frequencies) may also “soften” the image.
MPEG NR: Use the MPEG Filter to reduce or eliminate so-called “mosquito noise” in
MPEG-compressed video signals (digital broadcasts or DVDs). Adjust as needed to
minimize distortion around the edges of moving objects, moving artifacts around edges
and/or blotchy noise patterns superimposed over the objects.
Backlight: The Backlight control changes the apparent brightness of the displayed
image. Its effect is similar to that of a lamp intensity control on a projector.
Note
32
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The choices are 5400K, 6500K, 8500K and Custom. The default setting, 6500K, is
appropriate for most situations. Higher settings produce a “bluer” picture; lower ones
impart a reddish hue to the image.
Each color temperature setting has six (6) “white balance” parameters associated with it
(two each for red, green and blue). These are described later in this section; refer to White
Gamma: The Gamma control determines how gray shades are displayed between
minimum input (black) and maximum input (white) for all signals. A good gamma setting
helps to optimize blacks and whites while ensuring smooth transitions for the
“in-between” values utilized in other grays.
Unlike brightness and contrast controls, Gamma allows you to lighten or darken the
overall tone of your images without changing the extremes. All images will be more vibrant
while still showing good detail in dark areas.
The default Gamma setting of 2.2 is appropriate for most typical home theater
environments.
Save Settings: The Crystal Series LCD lets you save image quality settings for each input
and supported resolution to a preset. You can recall this preset at a later time by simply
pressing a button on the remote control or using the Restore Settings menu command
(see below).
You should save changes to any of the following settings to a preset; otherwise they will
be lost when a new input source or resolution is selected:
• Brightness
• Contrast
• Color saturation
• Tint
• Sharpness
• Gamma
• Color temperature selection (5400, 6500, 8500 or Custom)
menu and select “Custom,” “ISF Day” or “ISF Night.” Or, use the corresponding buttons
on the remote control.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio
To adjust the Crystal Series LCD audio settings, select Audio from the Main Menu and
press ENTER.
➤
Balance: To adjust the left/right speaker balance, select Balance from the Audio Menu
and press ENTER. Use the left- and/or right-arrow buttons to make one channel louder
than the other.
Equalizer: The Crystal Series LCD has a five-band graphic equalizer that you can use to
boost or cut certain audio frequencies. To use it, select Equalizer from the Audio menu
and press ENTER or
.
From this menu, you can create and store audio
“modes.” A mode is a combination of volume and
equalizer settings. The viewer can then recall these
settings using the AUDIO 1, AUDIO 2 and AUDIO 3
remote control buttons.
PIP
POSITION
SIZE
SWAP
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
To select and customize an audio mode –
Custom1 (AUDIO 1), Custom2 (AUDIO 2) or
Custom3 (AUDIO 3):
1. Use the
or
button to highlight its name. Then, press ENTER or
.
2. Press
or
to select the Volume slider or equalizer frequency band that you want
to adjust. The five frequency bands are 100, 300, 1000, 3000 and 10,000 Hertz (Hz).
3. Use the or button to adjust according to taste.
6. Press MENU or EXIT when you have finished configuring audio modes.
press ENTER. The effect is similar to using the MUTE button, except that the Crystal
Series LCD “remembers” this setting if you turn off the display, then turn it back on.
To set the Crystal Series LCD’s internal clock or configure the on/off timers, select Timer
from the Main Menu and press ENTER.
➤
Timer
Time: To set the Crystal Series LCD internal clock, select Time from the Timer menu and
press ENTER. Then, use the left- or right-arrow button to select the hour of the day,
AM/PM or the minute of the hour to set. Then, use the up- or down-arrow buttons to set
that component of the time.
Time
On Timer
Off Timer
Sleep Timer
When finished, press MENU or EXIT.
On Timer: Use the On Timer to turn the Crystal Series LCD on at a specific time of day.
You can also specify a source input and volume level.
Off Timer: Use the Off Timer to turn the Crystal Series LCD off at a specific time of day.
34
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer: Use the Sleep Timer to turn off the Crystal Series LCD after a specified
interval.
To set the Sleep Timer:
• Select Sleep Timer from the Timer menu and press ENTER.
– OR –
• Press the TIMER OFF button on the remote control.
Use the right- or left-arrow button to select 10, 30, 60, 120 or 180 minutes. Then, press
ENTER or MENU.
Use the controls in the Setup menu to perform advanced image quality adjustments and
access various other Crystal Series LCD features.
use the up- or down-arrow buttons to select the OSD language (English, French, Spanish,
Portuguese or German). Press ENTER again to confirm your selection.
or
button to set the OSD Timer. This timer controls how long
the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in
10-second increments. When you set the OSD to 0, the menus remain on-screen until
you hide them by pressing EXIT.
PC Mode Adjust: To improve the quality of displayed images from a computer or other
VESA-compliant, RGB (480p or higher) source, select PC Mode Adjust and press
ENTER.
• Auto Adjust: Auto Adjust automatically adjusts settings to optimize computer images.
To execute Auto Adjust on command, select Auto Adjust and press ENTER.
Auto Adjust may take some time to complete, depending on the
characteristics of the incoming signal.
Note
• Clock: Use the up- or down-arrow buttons (
,
) to highlight Clock. Then, use the
right-arrow button (
) to increase the pixel clock rate; use the left-arrow button (
)
to decrease it.
• Phase: Adjust the phase if the image shows shimmer or “horizontal noise.” Pixel phase
adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect
of this control is similar to that of a tracking control on a VCR.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may
notice that you can stabilize the image at more than one point. Use either setting in this
case.)
• H Position: Use the up- or down-arrow buttons (
use the right-arrow button ( ) to shift the image to the right; use the left-arrow button
) to shift the image to the left.
• V Position: Use the up- or down-arrow buttons (
,
) to highlight H Position. Then,
(
,
) to highlight V Position. Then,
use the right-arrow button (
) to shift the image up; use the left-arrow button ( ) to
shift the image down.
To restore the factory-default Clock, Phase and Position settings, select Factory Reset
and press ENTER.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
active picture area of the video signal out beyond the edge of the display area.
Some television programs are produced based on the assumption that older television
sets may not display the outer edges of the broadcast picture area. Overscan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
Use the on-screen slidebars to set the desired amount of horizontal and vertical overscan,
as well as horizontal and vertical image shift.
These settings only affect 480i source material. For HDTV, DVDs and other video sources,
Overscan is generally not necessary or desirable.
Letterbox Mode: Select Letterbox Mode from the
Setup menu to change the zoom factor that takes
effect when you select the Letterbox aspect ratio
Letterbox Mode = Letterbox
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
When you select Letterbox, the image is enlarged
(zoomed in) by a factor of approximately 1.33.
When you select Cinema Fill, the zoom factor is
approximately 1.77 (1.33 x 1.33).
Letterbox Mode = Cinema Fill
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
associates the PC AUDIO IN input with that HDMI input.
If the source does support audio output via HDMI, set this option to HDMI to route the
HDMI (digital) audio signal to the speakers and digital audio output when HDMI1, HDMI 2,
HDMI 3 or HDMI 4 is selected.
Film Mode: To smooth out moving images from interlaced, standard-definition (SD)
In most cases, the Crystal Series LCD detects the proper “pull-down” rate and vertical
frequency. However, if your source is jittery and/or tearing you may wish to specify the
pull-down rate (2:2 or 3:2) to ensure stable processing for that source.
Crystal Series LCD adjust the Backlight setting automatically, according to the ambient
light level in the viewing area.
Component for that input.
In most situations, the Auto setting works well.
36
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Crystal Series LCD’s RS-232 port. (This setting must match the data rate of the device
connected to the RS-232 input.)
shown here (Component 1 and Video 1 are not available).
>
HDMI 1
HDMI 2
HDMI 3
HDMI 4
SCART
Component 2
RGB
Video 2
are not using. By default, all inputs are enabled.
Disabling unused inputs causes the main input select function (using the SOURCE button
on the LCD keypad) to skip over them, saving time. The PIP input select function (using
the PIP SRC button on the remote control unit) is similarly affected.
• HDMI 1/HDMI 2/HDMI 3/HDMI 4: Enables or disables an HDMI source.
• Component 1/Component 2: Enables or disables the Component 1 or Component 2
source.
• RGB: Enables or disables the RGB source.
• Video 1/Video 2: Enables or disables the a video source.
If either Component 1 or Video is enabled, SCART must be disabled.
Note
When set to ON, the LED lights orange to indicate that the Crystal Series LCD is in
standby mode. When set to OFF, the LED is always off, regardless of the operational state
of the Crystal Series LCD.
identifies your display: its model number, serial number and installed firmware version.
Should you ever need to contact Runco Technical Support, this information will help them
answer your questions or resolve product performance issues.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the ISF Calibration menu to perform advanced picture quality adjustments. This
menu should be used by ISF-certified technicians only.
➤
Picture Adjust
White Balance
Blue Enable
You must enter a passcode to access the ISF Calibration menu.
Note
Factory Reset
Splash Duration
menu, but are accessible only by entering the ISF Calibration menu passcode. This makes
it possible to restore the picture quality settings to what they were when the Crystal Series
LCD was installed, simply by recalling the “ISF Night” or “ISF Day” preset.
lower-resolution Component, S-Video or Composite sources. For best results, adjust
The choices are 5400K, 6500K, 8500K and Custom. The default setting, 6500K, is
appropriate for most situations. Higher settings produce a “bluer” picture; lower ones
impart a reddish hue to the image.
Each color temperature setting has six (6) “white balance” parameters associated with
it (two each for red, green and blue). (The White Balance settings for the 5400K, 6500K
and 8500K color temperatures are factory-set and cannot be changed.)
To create a “Custom” color temperature, select Custom from the
Tip
Color Temp. menu and press ENTER. Then, press ENTER a
• Save Settings: For each input and supported resolution, the Crystal Series LCD lets
you save image quality settings as presets that you can recall at a later time. You can
create up to three presets – designated “Custom,” “ISF Day” and “ISF Night” – per
input and resolution.
You should save changes to any of the following settings to a preset; otherwise they
will be lost when a new input source or resolution is selected:
• Brightness
• Contrast
• Color saturation
38
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• Tint
• Sharpness
• Gamma
• Color temperature selection (5400, 6500, 8500 or Custom)
and select “Custom,“ “ISF Day” or “ISF Night.”
menu and select “Custom,” “ISF Day” or “ISF Night.” Or, use the corresponding buttons
on the remote control.
White Balance: To remove any trace of color from the white areas of the displayed
White Balance
R Gain
256
256
256
0
G Gain
• Gain: Use the Gain controls to correct color imbalances in the bright areas of the
image. A good way to do this is to use a test pattern consisting mostly of solid white
areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red,
green or blue, decrease the Gain for that color.
B Gain
R Offset
G Offset
B Offset
0
• Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test
pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the
gray areas contain traces of red, green or blue, decrease the Offset for that color.
0
Any white balance adjustments you make here are automatically
Note
stored as a “Custom” color temperature. The White Balance
settings for the 5400K, 6500K and 8500K color temperatures are
factory-set and cannot be changed. Always set the Color Temp.
to Custom before making any white balance adjustments, so
you can see how those adjustments affect the image.
Blue Enable: Blue Enable removes all red and green color information from the image,
simulating a blue filter. You can use it instead of a blue filter when performing color and tint
adjustments.
Factory Reset: To reset all Crystal Series LCD settings to their factory defaults, select
Factory Reset from the ISF Calibration menu and press ENTER. To confirm the reset,
press
or
to highlight Yes and press ENTER again. This command is not
undoable. Use it with caution!
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
appearing, set the Splash Duration to 0.
CALIBRATED FOR:
Runco Customer By: Runco Dealer
CUSTOM BUILT BY:
Figure 4-6. Crystal Series LCD Splash Screen
You can personalize the splash screen with the customer name,
Note
Runco dealer name or any other string. Refer to Personalizing the
instructions.
40
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
16:9
PIP
4:3
LETTER V WIDE
To use PIP, press the PIP button.
4.5
Using
POSITION
SIZE
SWAP
Picture-In-Picture (PIP)
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
The PIP window appears inside the main image
window.
Press PIP again to switch to side-by-side PIP
mode.
Press PIP again to turn PIP off.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
shows which of the other sources are available as a PIP source.
Table 4-2. Available Main and PIP Source Combinations
PIP Input Source
VIDEO 1
VIDEO 2
COMP. 1/SCART
COMP. 2
RGB
–
√
√
√
√
√
√
√
√
√
–
√
√
√
√
√
√
√
√
√
–
√
√
√
√
√
√
√
√
√
–
√
√
√
√
√
√
√
√
√
–
√
√
√
√
√
√
√
√
√
–
–
–
–
√
√
√
√
√
–
–
–
–
√
√
√
√
√
–
–
–
–
√
√
√
√
√
–
–
–
–
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Notes:
1. “√” means that that source is available as a PIP source when that input is selected; “–” means
that it is not.
2. The Crystal Series LCD cannot display the same source in both the main and PIP windows, nor
can it display two HDMI (digital) signals simultaneously.
16:9
PIP
4:3
LETTER V WIDE
Changing the PIP
Position
To change the PIP window position, press
the POSITION button on the remote
control repeatedly until the window is in the
desired position.
➤
POSITION
SIZE
SWAP
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
3
4
2
1
42
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
16:9
PIP
4:3
LETTER V WIDE
To change the PIP window size, press the
SIZE button on the remote control
repeatedly to achieve the desired window
size.
Changing the PIP Size
POSITION
SIZE
SWAP
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
16:9
PIP
4:3
LETTER V WIDE
To swap the main and PIP images, press
the SWAP button on the remote control.
Swapping the Main and
PIP Images
POSITION
SIZE
SWAP
PIP SRC AUDIO 1 AUDIO 2 AUDIO 3
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
44
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Maintenance and Troubleshooting
Regular cleaning will extend the life and performance of the Crystal Series LCD. Before
cleaning, be sure to unplug the power cord from the power outlet.
5.1
Cleaning
Do not under any circumstances use solvents such as benzene or thinner to clean the
Crystal Series LCD. Doing so may cause deterioration or peeling of paint from the display
or remote control unit.
Cleaning the Display
Panel Body and Remote
Control
Wipe the display and remote control gently with a soft cloth. In case of excessive dirt
buildup, dampen a soft cloth with a diluted neutral cleaning detergent. Wring the cloth
thoroughly, then wipe the component and dry it with a dry soft cloth.
After dusting, wipe the screen gently using a soft cloth (cotton, flannel etc.). Do not use
tissue or coarse fabric. The screen surface is easily scratched; do not rub it or hit it with a
hard object.
Cleaning the Screen
Cleaning the Vents
If you clean the surface of the screen with a wet cloth, do not allow water droplets on the
surface to enter into the product; this may cause a malfunction.
As a general rule, use a vacuum cleaner about once a month to clean the vents on the
rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting
when doing this). If not removed, accumulated dust can cause the internal temperature to
increase, resulting in possible breakdown or fire.
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the Crystal Series LCD. If the suggested solutions fail to resolve the
problem or if you encounter an issue not described here, please contact your Runco
dealer or Runco Technical Support.
5.2
Troubleshooting Tips
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
The display does not turn on
after initial installation.
• The Crystal Series LCD is
not plugged in or the AC
outlet is not active.
• Ensure that the Crystal
Series LCD is plugged in
and that the AC outlet is
active.
• The remote control
batteries have run out.
• Replace the batteries.
The display is on, but there is
no picture.
• Incorrect source selection.
• Source component is not
turned on.
• Select the correct source.
• Turn on the source
component.
• Source component is
connected incorrectly or
not at all.
• Check video connections
to source component.
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Troubleshooting Chart (continued)
Symptom
Possible Cause(s)
Solution
Picture is okay, but there is no
sound.
• Audio output is muted.
• Press the MUTE button
on the remote control.
• Volume setting is too low.
• Source component is
connected incorrectly or
not at all.
• Turn up the volume.
• Check audio connections
to source component.
• Speakers are connected
incorrectly or not at all.
• Audio settings are
incorrect.
• Check speaker
• Check the following
settings: Speaker
audio souces, ensure that
the audio output format is
“PCM” (refer to the manual
for the source
component).
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high.
• Brightness is set too high.
• Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Lower the brightness
setting.
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
Crystal Series LCD.
• Ensure that the source
outputs are connected to
the correct Crystal Series
LCD input.
RGB-HD images appear
“noisy.”
• Clock and Phase settings
need adjustment.
• Manually adjust Clock and
Phase settings, or perform
an Auto-Adjust (refer to
page 35).
“Invalid mode” appears
on-screen.
• The resolution and
frequency of the video
card in the computer are
not compatible with the
Crystal Series LCD.
• Select a compatible
resolution and vertical
frequency (refer to
page 59).
The image is too large or too
small.
• Image size needs
adjusting.
• Adjust the image size (refer
page 35).
46
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Serial Communications
To interface the Crystal Series LCD with a home theater automation/control system or a
6.1
®
PC running terminal emulation software (such as HyperTerminal, provided with Microsoft
straight-through cable.
RS-232 Connection
and Port Configuration
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop
bit and no flow control. Set the baud rate to match that of the Crystal Series LCD RS-232
page 37).
• Commands are in ASCII format and are not case-sensitive.
• A carriage return is not required after a command.
6.2
Serial Command
Syntax
• To send a command from a PC running terminal emulation software, create a text file
containing that command. Then, use the file transfer function in your terminal emulation
program to send the command. (If you are using HyperTerminal, choose “Send Text
File...” from the Transfer menu.)
• When you send a valid command, the Crystal Series LCD executes it and
acknowledges it with a right-bracket character (]) followed by the four-digit numeric
code you sent; for example, ]0002.
• When you send an invalid command (one followed by values outside the valid range for
that command), the Crystal Series LCD ignores it and returns >MAXor <MINinstead of
the four-digit code.
• When you send an unrecognized/misspelled command, the Crystal Series LCD ignores
it and returns -N/Ainstead of the four-digit code.
Table 6-1 lists the RS-232 command set.
Table 6-1. Serial Commands
Command
Description
Set audio volume to ### ( = 000-100)
[
S3A 0###
Example: [S3A0075sets volume to 75
Audio volume up
[
[
[
+3A
Audio volume down
-3A
Audio mute
S3E 000#
0 = not muted, 1 = muted
Example: [S3E0001mutes the audio output
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
Description
Main input selection
1 = Video 1
[
S4A 000#
2 = Video 2
3 = Component 1/SCART
4 = Component 2
5 = HDMI 3
6 = RGB
7 = HDMI 4
8 = HDMI 1
9 = HDMI 2
Example: [S4A0006selects RGB
Select “next” Main AV input
[
[
+4A
Aspect ratio selection
0 = 4:3
S4E 000#
1 = VirtualWide
2 = Letterbox
3 = 16:9
Example: [S4E0002selects Letterbox
PIP Input selection
1 = Video 1
[
S4G 000#
2 = Video 2
3 = Component 1/SCART
4 = Component 2
5 = HDMI 3
6 = RGB
7 = HDMI 4
8 = HDMI 1
9 = HDMI 2
Example: [S4G0003selects PIP Component 1 or SCART
Select “next” PIP AV input
[
[
+4G
Power on/off control
0 = standby, 1 = on
SAB 000#
Example: [SAB0001turns unit on
Set PIP mode
0 = OFF
[
SDA 000#
1 = PIP
2 = PBP
Example: [SDA0002selects PBP
Set PIP size
0 = small
[
SDB 000#
1 = medium
2 = large
Example: [SDB0001selects medium PIP size
48
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
Description
Set PIP aspect ratio
0 = 4:3
[
SDE 000#
1 = 16:9
Example: [SDE0001selects 16:9 aspect ratio PIP window
Set PIP window position
0 = Top/Left
[
SDF 000#
1 = Top/Right
2 = Bottom/Left
3 = Bottom/Right
Example: [SDF0001positions PIP window in upper-right corner of display area
The following serial commands are meant to emulate buttons on the remote control. Each button
has its own serial command, so effectively it is as if you were using the IR remote only you’ll be
doing so via serial commands. These commands provide active OSD responses just like the IR
remote.
Each command begins with [keyfollowed by the four-digit number of the button. No carriage
return is necessary. The response you receive from the unit if the command is valid will be a
right-bracket (]) followed by the four-digit numeric code you sent. (For example, the ‘ON’ com-
mand is [key0015; the response will be ]0015). All commands are in ASCII.
OFF
[
key 0002
0015
ON
Number 1
Number 2
Number 3
Number 4
Number 5
Number 6
Number 7
Number 8
Number 9
Number 100
Number 0
HDMI 1
[
key 0004
0005
0006
0008
0009
0010
0012
0013
0014
0035
0017
[
key 0102
0101
HDMI 2
HDMI 3
0093
HDMI 4
0094
Component 1/SCART
0028
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
Description
Component 2
RGB
0001
0019
Video 1
0105
Video 2
0027
CUSTOM
ISF NIGHT
ISF DAY
[
[
key 0003
0062
0031
16:9
key 0040
0043
4:3
LETTERBOX
VIRTUALWIDE
Right-Arrow key
Down-Arrow key
Up-Arrow key
Left-Arrow key
ENTER
0039
0126
[
key 0007
0016
0018
0011
0046
MENU
[
[
[
key 0026
key 0100
key 0036
0047
EXIT
PIP SRC
PIP SIZE
PIP POSITION
PIP
0034
0032
TIMER OFF
SWAP
0037
0033
MUTE
[
key 0091
0055
INFO
AUDIO 1
AUDIO 2
AUDIO 3
BRIGHT +
0084
0085
0086
[
key 0087
50
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
Description
BRIGHT -
CONTR +
CONTR -
0088
0089
0090
To personalize the start-up splash screen with the customer name, Runco dealer name or
any other string (up to 28 characters long), send the following commands:
Personalizing the Splash
Screen Using Serial
Commands
• [c############################]to program the customer name or other
string (represented by ############################)
• [d############################]to program the dealer name or other string
(represented by ############################)
To send a command from a PC running terminal emulation software, create a text file
program to send the command. (If you are using HyperTerminal, choose “Send Text
When you do, the Crystal Series LCD echoes the string back to the control system or PC,
enclosed in quotes (for example, "Runco Customer"). If it doesn’t, verify that you sent
the command correctly.
To see the changes take effect, cycle power to the Crystal Series LCD.
For example, sending the commands [cRunco Customer] and
[dBy: Runco Dealer] causes the splash screen to look like this:
CALIBRATED FOR:
Runco Customer By: Runco Dealer
CUSTOM BUILT BY:
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
52
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Table 7-1 lists the Crystal Series LCD specifications.
7.1
Crystal Series LCD
Specifications
Table 7-1. Crystal Series LCD Specifications
Native Resolution:
1920 x 1080
Screen Size:
CX-47HD/CX-OPAL47 = 47 in. (diagonal)
CX-65HD = 65 in. (diagonal)
Screen Aspect Ratio:
Available Aspect Ratios:
DTV Compatibility:
ISF Settings:
16:9
4:3, Letterbox, 16:9, VirtualWide™
480i/p, 576i/p, 720p, 1080i, 1080p
Yes
Contrast Ratio:
CX-47HD/CX-OPAL47 = 3000:1
CX-65HD = 2000:1
Data/Graphics Compatibility:
Response Time (typical):
Vivix Processing:
Refer to Table 7-2
4 milliseconds
3:2 or 2:2 pull down
Video/Audio Inputs:
Multiple input combinations with up to
(2) Composite Video
(1) S-Video
(2) Component Video
(4) HDMI 1.3a w/HDCP
(1) RGB (15-pin D-sub)
(5) Analog Audio
(4 stereo RCA pairs + 3.5-mm stereo mini jack)
Control Inputs:
(1) RS-232 (9-pin D-sub)
(1) Wired IR (3.5-mm mono mini jack)
Outputs:
(1) Digital Audio (S/PDIF optical)
(1) Stereo Speakers
Audio System:
10W RMS x 2 Stereo Amplifier
Source, power and aspect ratios
100 to 240 VAC, 50/60Hz
Discrete IR Control:
Power Requirements:
Power Consumption (typical):
CX-47HD/CX-OPAL47 = 350 watts (1194.5 BTUs/hour);
5 watts in standby mode
CX-65HD = 640 watts (2184.3 BTUs/hour); 8 watts in
standby mode
Operating Environment:
40ºF to 95ºF (5ºC to 35ºC);
20% to 80% humidity (non-condensing);
Altitude = 9,842 feet (3,000 meters)
Dimensions:
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-1. Crystal Series LCD Specifications (continued)
Weight (including stand):
CX-47HD/CX-OPAL47 = 121.3 lbs. (55.00 kg)
CX-65HD = 220.5 lbs. (100.00 kg)
Regulatory Approvals:
Complies with UL, FCC, CE, RoHS, C-Tick, NOM, GOST
Limited Warranty:
Two (2) years parts and labor from the date of delivery to
the end user.
Specifications are subject to change without notice.
54
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
12
6
6
Ventilative hole dimension
Ventilative hole dimension
166.8
100.3
66
180
440
180
Mounting hole dimension (8x)
82.6
310
4
Ventilative hole dimension
Figure 7-4. CX-65HD Overall Dimensions (Rear/Side)
58
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2 lists the signal types supported by each input on the Crystal Series LCD.
7.3
Supported Timings
Table 7-2. Supported Signal Timings by Input
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
HDMI 1
HDMI 2
HDMI 3
HDMI 4
Video 1
Video 2
S-Video
SCART
Refresh
Rate (Hz)
Pixel Frequency
(MHz)
Format
Resolution
Component 1
Component 2
RGB
60.00
72.00
75.00
85.00
60.00
72.00
75.00
85.00
60.00
70.00
75.00
85.00
75.00
60.00
60.00
75.00
85.00
60.00
85.00
60.00
75.00
85.00
60.00
60.00
60.00
75.00
60.00
31.469
37.861
37.500
43.269
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
67.500
47.400
47.776
60.289
68.633
60.000
85.938
63.981
79.976
91.146
47.720
64.700
65.317
82.300
75.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
108.000
68.250
79.500
102.250
117.500
108.000
148.500
108.000
135.000
157.500
84.750
101.000
121.750
156.000
162.000
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
640x480
640x480
800x600
800x600
1024x768
1152x864
1280x768
1024x768
1152x864
1280x768
1280x960
1280x960
1280x1024 1280x1024
1360x768
1360x768
1400x1050 1400x1050
1600x1200 1600x1200
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2. Supported Signal Timings by Input (continued)
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
HDMI 1
Video 1
Video 2
S-Video
SCART
Refresh
Rate (Hz)
Pixel Frequency
(MHz)
Format
Resolution
Component 1
Component 2
HDMI 2
HDMI 3
HDMI 4
RGB
1920x1200 1920x1200
60.00
29.97
59.94
50.00
50.00
50.00
59.94
24.00
25.00
30.00
24.00
25.00
30.00
59.94
59.94
50.00
50.00
74.000
15.734
31.469
15.625
31.250
37.500
44.964
26.997
28.125
33.749
26.990
28.200
33.750
15.734
15.734
15.625
15.625
154.000
13.500
27.000
13.500
27.000
74.250
74.250
74.250
74.250
74.250
74.250
74.250
74.250
3.580
√
√
√
√
√
√
√
√
√
√
–
√
√
–
–
√
–
–
√
√
√
√
√
√
√
√
√
–
√
√
–
–
√
–
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
√
–
–
√
–
–
–
–
–
–
–
–
–
–
–
√
√
√
√
480/60i
480/60p
576/50i
712x484
720x483
720x576
576/50p
720/50p
720/60p
1080/24i
1080/25i
1080/30i
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1080/24p 1920x1080
1080/25p 1920x1080
1080/30p 1920x1080
NTSC 3.58
NTSC 4.43
PAL
–
–
702x574
–
4.430
13.500
13.500
SECAM
60
CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL NUMBER
020-0969-00 Rev. B
January 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
|