PG3800
PG2200
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions/Consignes de sécurité/Sicherheitsvorkehrungen/Instrucciones de seguridad
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain
or moisture. To reduce the hazard of electrical shock, do not remove cover or back.
No user serviceable parts inside. Please refer all servicing to qualified personnel.The
lightning flash with an arrowhead symbol within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons. The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
ATTENTION: Pour éviter tout risque d’électrocution ou d’incendie, ne pas exposer
cet appareil à la pluie ou à l’humidité. Pour éviter tout risque d’électrocution, ne
pas ôter le couvercle ou le dos du boîtier. Cet appareil ne contient aucune pièce
remplaçable par l'utilisateur. Confiez toutes les réparations à un personnel quali-
fié. Le signe avec un éclair dans un triangle prévient l’utilisateur de la présence
d’une tension dangereuse et non isolée dans l’appareil. Cette tension constitue
un risque d’électrocution. Le signe avec un point d’exclamation dans un triangle
prévient l’utilisateur d’instructions importantes relatives à l’utilisation et à la
maintenance du produit.
Important Safety Instructions
Consignes de sécurité importantes
1. Please read all instructions before operating the unit.
2. Keep these instructions for future reference.
3. Please heed all safety warnings.
1. Veuillez lire toutes les instructions avant d’utiliser l’appareil.
2. Conserver ces instructions pour toute lecture ultérieure.
3. Lisez avec attention toutes les consignes de sécurité.
4. Follow manufacturers instructions.
5. Do not use this unit near water or moisture.
6. Clean only with a damp cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manu-
facturers instructions.
4. Suivez les instructions du fabricant.
5. Ne pas utiliser cet appareil près d’une source liquide ou dans un lieu humide.
6. Nettoyez l’appareil uniquement avec un tissu humide.
7. Veillez à ne pas obstruer les fentes prévues pour la ventilation de l’appareil.
Installez l’appareil selon les instructions du fabricant.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polar-
ized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or third prong is provided
for your safety. When the provided plug does not fit your outlet, consult an electri-
cian for replacement of the obsolete outlet.
8. Ne pas installer près d’une source de chaleur (radiateurs, etc.) ou de tout équi-
pement susceptible de générer de la chaleur (amplificateurs de puissance par
exemple).
9. Ne pas retirer la terre du cordon secteur ou de la prise murale. Les fiches
canadiennes avec polarisation (avec une lame plus large) ne doivent pas être
modifiées. Si votre prise murale ne correspond pas au modèle fourni, con-
sultez votre électricien.
10. Protect the power cord from being walked on and pinched particularly at plugs,
convenience receptacles and at the point at which they exit from the unit.
11. Unplug this unit during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified personnel. Servicing is required when the unit has
been damaged in any way, such as power supply cord or plug damage, or if liquid
has been spilled or objects have fallen into the unit, the unit has been exposed to
rain or moisture, does not operate normally, or has been dropped.
10. Protégez le cordon secteur contre tous les dommages possibles (pincement,
tension, torsion,, etc.). Veillez à ce que le cordon secteur soit libre, en particu-
lier à sa sortie du boîtier.
11. Déconnectez l’appareil du secteur en présence d’orage ou lors de périodes
d’inutilisation prolongées.
12. Consultez un service de réparation qualifié pour tout dysfonctionnement
(dommage sur le cordon secteur, baisse de performances, exposition à la
pluie, projection liquide dans l’appareil, introduction d’un objet dans le boî-
tier, etc.).
ACHTUNG: Um die Gefahr eines Brandes oder Stromschlags zu verringern, sollten
Sie dieses Gerät weder Regen noch Feuchtigkeit aussetzen.Um die Gefahr eines
Stromschlags zu verringern, sollten Sie weder Deckel noch Rückwand des Geräts ent-
fernen. Im Innern befinden sich keine Teile, die vom Anwender gewartet werden kön-
nen. Überlassen Sie die Wartung qualifiziertem Fachpersonal.Der Blitz mit Pfeilspitze im
gleichseitigen Dreieck soll den Anwender vor nichtisolierter “gefährlicher Spannung”
im Geräteinnern warnen. Diese Spannung kann so hoch sein, dass die Gefahr
eines Stromschlags besteht. Das Ausrufezeichen im gleichseitigen Dreieck soll den
Anwender auf wichtige Bedienungs- und Wartungsanleitungen aufmerksam machen,
die im mitgelieferten Informationsmaterial näher beschrieben werden.
Wichtige Sicherheitsvorkehrungen
PRECAUCION: Para reducir el riesgo de incendios o descargas, no permita que
este aparato quede expuesto a la lluvia o la humedad. Para reducir el riesgo de
descarga eléctrica, nunca quite la tapa ni el chasis. Dentro del aparato no hay
piezas susceptibles de ser reparadas por el usuario. Dirija cualquier reparación al
servicio técnico oficial. El símbolo del relámpago dentro del triángulo equilátero
pretende advertir al usuario de la presencia de “voltajes peligrosos”no aislados
dentro de la carcasa del producto, que pueden ser de la magnitud suficiente
como para constituir un riesgo de descarga eléctrica a las personas. El símbolo
de exclamación dentro del triángulo equilátero quiere advertirle de la existencia
de importantes instrucciones de manejo y mantenimiento (reparaciones) en los
documentos que se adjuntan con este aparato.
1. Lesen Sie alle Anleitungen, bevor Sie das Gerät in Betrieb nehmen.
2. Bewahren Sie diese Anleitungen für den späteren Gebrauch gut auf.
3. Bitte treffen Sie alle beschriebenen Sicherheitsvorkehrungen.
4. Befolgen Sie die Anleitungen des Herstellers.
5. Benutzen Sie das Gerät nicht in der Nähe von Wasser oder Feuchtigkeit.
6. Verwenden Sie zur Reinigung des Geräts nur ein feuchtes Tuch.
7. Blockieren Sie keine Belüftungsöffnungen. Nehmen Sie den Einbau des Geräts nur
entsprechend den Anweisungen des Herstellers vor.
8. Bauen Sie das Gerät nicht in der Nähe von Wärmequellen wie Heizkörpern,
Wärmeklappen, Öfen oder anderen Geräten (inklusive Verstärkern) ein, die Hitze
erzeugen.
9. Setzen Sie die Sicherheitsfunktion des polarisierten oder geerdeten Steckers nicht
außer Kraft. Ein polarisierter Stecker hat zwei flache, unterschiedlich breite Pole. Ein
geerdeter Stecker hat zwei flache Pole und einen dritten Erdungsstift. Der breitere
Pol oder der dritte Stift dient Ihrer Sicherheit. Wenn der vorhandene Stecker nicht
in Ihre Steckdose passt, lassen Sie die veraltete Steckdose von einem Elektriker
ersetzen.
10. Schützen Sie das Netzkabel dahingehend, dass niemand darüber laufen und
es nicht geknickt werden kann. Achten Sie hierbei besonders auf Netzstecker,
Mehrfachsteckdosen und den Kabelanschluss am Gerät.
11. Ziehen Sie den Netzstecker des Geräts bei Gewittern oder längeren Betriebspausen
aus der Steckdose.
12. Überlassen Sie die Wartung qualifiziertem Fachpersonal. Eine Wartung ist not-
wendig, wenn das Gerät auf irgendeine Weise, beispielsweise am Kabel oder
Netzstecker beschädigt wurde, oder wenn Flüssigkeiten oder Objekte in das Gerät
gelangt sind, es Regen oder Feuchtigkeit ausgesetzt war, nicht mehr wie gewohnt
betrieben werden kann oder fallen gelassen wurde.
Instrucciones importantes de seguridad
1.
2.
3.
4.
5.
6.
7.
Lea todo este manual de instrucciones antes de comenzar a usar la unidad.
Conserve estas instrucciones para cualquier consulta en el futuro.
Cumpla con todo lo indicado en las precauciones de seguridad.
Observe y siga todas las instrucciones del fabricante.
Nunca utilice este aparato cerca del agua o en lugares húmedos.
Limpie este aparato solo con un trapo suave y ligeramente humedecido.
No bloquee ninguna de las aberturas de ventilación. Instale este aparato de
acuerdo a las instrucciones del fabricante.
8.
No instale este aparato cerca de fuentes de calor como radiadores, calenta-
dores, hornos u otros aparatos (incluyendo amplificadores) que produzcan
calor.
9.
No anule el sistema de seguridad del enchufe de tipo polarizado o con
toma de tierra. Un enchufe polarizado tiene dos bornes, uno más ancho que
el otro. Uno con toma de tierra tiene dos bornes normales y un tercero para
la conexión a tierra. El borne ancho o el tercero se incluyen como medida de
seguridad. Cuando el enchufe no encaje en su salida de corriente, llame a
un electricista para que le cambie su salida anticuada.
10. Evite que el cable de corriente quede en una posición en la que pueda ser
pisado o aplastado, especialmente en los enchufes, receptáculos y en el
punto en el que salen de la unidad.
11. Desconecte de la corriente este aparato durante las tormentas eléctricas o
cuando no lo vaya a usar durante un periodo de tiempo largo.
12. Dirija cualquier posible reparación solo al servicio técnico oficial. Deberá
hacer que su aparato sea reparado cuando esté dañado de alguna forma,
como si el cable de corriente o el enchufe están dañados, o si se han derra-
mado líquidos o se ha introducido algún objeto dentro de la unidad, si esta
ha quedado expuesta a la lluvia o la humedad, si no funciona normalmente
o si ha caído al suelo.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
PG Series Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Guided Tour - Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Guided Tour - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting Up and Using Your PG Series . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting Up and Using Your PG Series . . . . . . . . . . . . . . . . . . . . . . . . . . 6
The PG Series Protection Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bridge and Parallel Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PG Series Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PG Series Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Copyright 2008, Samson Technologies Corp.
Printed October, 2008 v1.2
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the PG2200 or PG 3800 power amplifier from Samson! We know you don’t like reading
owners manuals, but you’ve just purchased one of the finest sound reinforcement power amplifiers around, and we
want to tell you about it! So, before you plug in, we’d like to suggest you take just a few moments out to scan these
pages. We’ll make it as painless as possible, we promise—and, who knows, you might just pick up a tip or two. The
Samson PG Series stereo power amplifiers have been designed to a specification we call Pure Gain Amplification.
The PG series amplifiers provide robust, clean output with low distortion and wide dynamic range, along with the
dependability demanded by the most professional audio engineers and installers. This manual covers both the
PG2200 and PG3800 models. The PG series convenient 2 rack-space design is compact, and yet there’s plenty of power
available, with 2 x 280 Watts at 8Ω, 2 x 500 Watts at 4Ω and 2 x 1000 Watts at 2Ω for the PG2200 and 2 x 560 Watts at
8Ω, 2 x 900 Watts at 4Ω and 2 x 1800 Watts at 2Ω for the PG3800. For mono applications, a Bridge mode links both
channels of the amplifiers, thus providing even more power, with massive mono power ratings of 1000 watts at 8Ω,
2200 watts at 4Ω for the PG2200 and 1800 watts at 8Ω, 3800 watts at 4Ω for the PG3800. Making input connections
is simple since the PG series’rear panel provides both balanced XLR and balanced 1/4-inch TRS connections. For the
outputs, the PG Series amplifiers provide standard 5-way binding posts, as well as dual Speakon™ connectors. The
front-panel controls and displays include a large power switch with LED indicator, as well as independent left and
right channel input level controls. To help you set the correct operating levels, the PG series amplifiers include front
panel Signal, Peak and Protection LED indicators. The PG series amplifiers also include onboard dynamics processing
with a selectable Low Frequency Filter at 30 Hz to help remove stage rumble and a selectable Limiter to help protect
your speakers and help keep your signal clean. Like all serious power amplifiers, the PG Series internal electronics are
based around a serious power-core, with over-sized toroidal transformers and large extruded heat sinks. To keep the
PG series amplifiers running cool, their designs employ twin internal wind tunnels with forced-air cooling via two
temperature-sensitive, variable speed fans, which greatly reduces the chance of thermal and overheating problems.
Multi-stage protection for power-up, over-heating, over-current, short circuit, low output impedance and DC voltage,
assures high reliability under the most demanding situations. The PG series amps are road tough with their all steel
chassis, 19-inch rack mount design and convenient carry handles, the PG series amplifiers are ready for a life of travel,
or at home in a nice fixed installation. Optimized for live sound venues, houses of worship, commercial installations,
and for driving small and medium-sized live PA systems, the PG series amplifiers will deliver reliable power from gig-
to-gig and venue-to-venue, day in and night out.
With proper care and adequate air circulation, your PG Series amplifier will operate trouble free for many years. We rec-
ommend you record your serial number in the space provided below for future reference.
Serial number:_____________________________________
Date of purchase: ___________________________________
In these pages, you’ll find a detailed description of the many features of the PG Series power amplifier, as well as a
guided tour through its front and rear panels, step-by-step instructions for its setup and use, and full specifications.
You’ll also find a warranty card enclosed—please don’t forget to fill it out and mail it in so that you can receive online
technical support and so we can send you updated information about these and other Samson products in the future.
SPECIAL NOTE: Should your PG Series ever require servicing, a Return Authorization number (RA) is necessary. Without
this number, the unit will not be accepted. If purchased in the United States, please call Samson at 1-800-372-6766 for
a Return Authorization number prior to shipping the unit. If purchased outside the United States, contact your local
Samson dealer for details. Please retain the original packing materials and, if possible, return the unit in its original
carton and packing materials. If you purchased your Samson product outside the United States, please contact your
local distributor for warranty information and service.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PG Series Features
The Samson PG Series power amplifier utilizes the latest technology in professional power amplifier design. Here are
some of its main features:
•
Power to spare - Each amplifier delivers the following power ratings:
PG2200 2 x 280 Watts at 8Ω, 2 x 500 Watts at 4Ω and 2 x 1000 Watts at 2Ω
PG3800 2 x 560 Watts at 8Ω, 2 x 900 Watts at 4Ω and 2 x 1800 Watts at 2Ω
•
•
For mono applications, the amplifiers can operate in Bridge mode which links both channels providing even more power.
Massive mono power ratings of 1000 watts at 8Ω and 2200 watts at 4Ω for the PG2200 and a 1800 watts at 8Ω and 3800 watts
at 4Ω for the PG3800.
Clean, crisp sound - Impressive audio specifications such as 0.04% THD, dynamic range of 105 dB, crosstalk of 80 dB, and fre-
quency response of 5 Hz to 55 kHz guarantee ultra-clean sound quality.
•
•
Independent input level controls for each channel allow precision adjustments.
LED signal indicators for each channel continuously display power output levels and allow you to correct for overloading (clip-
ping) conditions.
•
•
•
In order to help keep the input signal clean, the PG series amplifiers have a selectable Limiter, which also helps protect the
connected speakers.
Both the PG2200 and PG3800 have a rear panel, selectable Low Frequency Filter at 30 Hz to help remove unwanted low fre-
quency rumble.
Unique stable bipolar circuit design that continuously keeps DC output during idling at or near zero volts (thus keeping idle
speakers at their zero point). This serves to minimize heat overload problems by effectively preventing the PG Series from
applying power when unnecessary.
•
•
Forced air cooling via two temperature-sensitive, variable speed fans provides reliable performance without thermal and
overheating problems.
Protection relay circuitry that guards against overheating or faulty wiring conditions and also prevents “thumps”when power-
ing on or off. This means that you can use the PG Series with a single power strip into which a mixer or other audio devices are
connected, without danger of damage to connected speakers.
•
•
•
•
Each channel provides both balanced XLR and balanced 1/4-inch TRS input connectors for easy connections.
Output connections are made via 5-way binding posts and Speakon™ connectors.
Toroidal transformer power supply for high current and low profile.
The PG Series can be mounted in any standard 19" rack (taking just two rack spaces), making it easy to integrate the amp into
any fixed or traveling PA rig.
•
Rugged construction (an all-steel chassis with a cool gray finish and a lightweight anodized aluminum heatsink) makes the PG
Series eminently roadworthy.
•
•
Extended three-year warranty.
Last but certainly not least, value. The Samson PG Series has been designed from the ground up to deliver excellent yet
affordable sound quality.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Guided Tour - Front Panel
1
2
3
4
5
6
4
1
7
8
8
7
1: Handle - For easy transport while carrying, or while rack mounting, the PG amplifier features two die-cast handles located con-
veniently on the left and right side of the front panel.
2: POWER switch - Use this to power the PG Series on or off. The internal LED lights whenever the PG Series is powered on.
3: Vent -The PG series amplifiers stay cool thanks to their twin, forced-air cooling tunnels. Cool air is drawn through the front
panel vents, reducing the temperature of the internal components while forcing the heat out the rear vents. The fans will actually
sense the internal temperature and adjust their speed to maintain the optimum cooling conditions.
4 VOLUME controls - These 42-position detented controls allow you to precisely adjust the input level of the signal arriving at
the rear-panel input jacks (see #2 on the following page). At their fully counterclockwise position (labeled “MIN”), the signal is
attenuated by 80 dB (essentially completely off). At their fully clockwise position (labeled “MAX”), the controls are at unity gain
(that is, no attenuation). When +4 dBu of signal arrives at the input jacks and the Channel input level controls are set to their fully
clockwise “MAX”position, the PG Series delivers full power output.
5: POWER LED - The front panel LED indicator will illuminate when the Power switch is set to the “ON”position.
6: PROTECT LED - This goes on for approximately five seconds whenever the PG Series is powered on and then turns off (you’ll
hear a “click”when it does so). The Protection LED will also light when overheating or other severe problems occur (see page 8
in this manual for more information). It is normal for the Protection LED to fade slowly when the amp is powered off. When lit,
no signal is provided to any connected speakers, thus muting them and preventing any “thump”from occurring. For a complete
description of the conditions under which this light goes on, see the section entitled “The PG Series Protection Circuitry”on page
8 of this manual.
7: CLIP LED - The CLIP segment lights whenever the channel is outputting signal at full strength. For the best signal-to-noise ratio,
the (CLIP) segment should light occasionally during peak levels; if it lights frequently, you may be overloading the PG Series and a
distorted (“clipped”) signal is probably being output. If this occurs and backing off the Input Level control delivers too low an out-
put level for your application, consider using Bridge mode (see the “Bridge and Parallel Modes”section on page 9 in this manual
for more information).
8: SIGNAL LED - The front panel LED indicators continuously monitor the power output level for the corresponding channel. The
SIGNAL LED lights whenever output signal is present
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Guided Tour - Rear Panel
2
3
4
5
1
1
2
9
8
7
6
1: Fan - This variable-speed fan provides vital cooling to your PG Series (the hotter the amp gets, the faster the fan blows!). Make
sure that both the front and rear panels are kept free of all obstructions and that cool, fresh air is accessible at all times. Also, try
to ensure that the PG Series is used in a dust-free environment.
2: Input connectors - Connect incoming signals to these electronically balanced connectors, using either XLR or 1/4" TRS (Tip/
Ring/Sleeve) plugs, wired as follows: Pin 2 (or Tip) hot, Pin 3 (or Ring) cold, and Pin 1 (or Sleeve) ground. We recommend the use
of balanced three-conductor cabling wherever possible (unbalanced two-conductor 1/4" plugs can also be inserted into these
inputs, but you’ll get better signal quality and less outside noise and hum if you use balanced lines). The PG Series accepts input
levels of any strength but needs at least +4 dBu to achieve maximum power. Stereo signals should be connected to both the
Channel 1 and Channel 2 input jacks; however, when operating the PG Series in Bridge or Parallel modes, use the Channel 1 input
jack only. See page 9 in this manual for more information about Parallel mode and pages 10 and 11 in this manual for full inter-
connection instructions.
3: Low Frequency Filter - This toggle switch is used to engage a low cut filter, 12 dB per octave at 30 Hz.
4: 5-way Binding Post - Use these to connect each channel of the PG Series to 4-ohm or 8-ohm loudspeakers. Be sure to con-
nect the loudspeaker correctly, with the red (+) terminal normally connected to the positive input of the speaker and the black
(ground) terminal normally connected to the negative input of the speaker. See page 9 in this manual for more information
about Bridge mode and pages 10 and 11 in this manual for full speaker connection instructions.
5: Circuit Breaker - This circuit breaker will trip if there is a fault with the mains voltage or if maximum output is exceeded (very
highly distorted). Push it in (once only!) to restart the amplifier after a short rest period.
6: AC input - Connect the supplied heavy-gauge 3-pin “IEC”power cable here.
7: Speakon™ output connectors - Alternatively, you can use these to connect each channel of the PG Series to 4 or 8-ohm
loudspeakers. See page 9 in this manual for more information about Bridge mode and pages 10 and 11 in this manual for full
Speakon™ connector wiring and interconnection instructions.
8: Bridge / Stereo / Parallel switch - For normal operation, place this three-way switch in its center (“STEREO”) position. When
placed in its left (“PARALLEL”) position, the signal arriving at the Channel 1 input only is routed to the power amplifiers of both
Channel 1 and Channel 2 (the Channel 2 input is ignored). When placed in its right (“BRIDGE”) position, the signal arriving at the
Channel 1 input only is again routed to both power amplifiers (again, the Channel 2 input is ignored), but the two power amplifi-
ers are bridged together. For more information, see the “Bridge and Parallel Modes”section on page 9 in this manual and the “PG
Series Connections”section on pages 10 -11 in this manual. WARNING: Due to the extremely high power output of the PG Series
when used in Bridge mode, be sure to use only loudspeakers sufficiently rated to handle the resultant wattage (in Bridge mode,
these must be 4 or 8-ohm speakers).
9: Limiter - This toggle switch is used to engage the Limter circuit, an automatic dynamics processor used to hold the input signal
at a fixed threshold level which helps keep a clean signal and protect the connected speakers.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Setting Up and Using Your PG Series
Setting up your PG Series is a simple procedure which takes only a few minutes:
1. Remove all packing materials (save them in case of need for future service) and decide
where the amplifier is to be physically placed—it can be used free-standing or mounted in
a standard 19”rack, requiring only two rack spaces. When installed, make sure that both
the front and rear panels are unobstructed and that there is good ventilation around the
entire unit (we recommend the use of spacer panels, especially if multiple amplifiers are
used in a rack.
Bridge / Stereo / Parallel switch
2. Set the rear panel Bridge/ Stereo / Parallel switch as desired (see the “Bridge and Parallel
Modes”section on page 9 in this manual for more information).
3. Make the speaker connections, using the banana, or Speakon™ output connectors on
the rear panel. It is never a good idea to power up any amplifier that is not connected
to loudspeakers. When operating in Stereo or Parallel mode, any loudspeakers with a
minimum impedance load of 2 ohms (that is, 2 ohms or greater) can be used; however,
in Bridge mode, 4 or 8 ohm speakers must be used. Be sure to connect the loudspeaker
correctly. In Stereo or Parallel mode, make sure the red (+) terminal is connected to the
positive input of the speaker and the black (ground) terminal is connected to the negative
input of the speaker. See page 9 in this manual for more information about Bridge mode
and pages 10 - 11 in this manual for full speaker interconnection instructions.
Output connectors
4. Next, make the signal input connections, using the XLR or 1/4-inch TRS input connectors
on the rear panel (if operating the PG Series in Bridge or Parallel mode, use the Channel
1 input only—see page 9 in this manual for more information). If your mixer or crossover
network has balanced outputs, we recommend the use of three-conductor cabling and
connectors (unbalanced two-conductor plugs can also be inserted into the 1/4-inch
TRS inputs, but you’ll get better signal quality and less outside noise and hum if you use
balanced lines).
Input connectors
5. For most applications, we recommend that you set the built-in Limiter switch to “ON”,
which will help protect your speaker system and help keep your signal clean. The Limiter is
a dynamic gain control; essentially a compressor with a fixed ratio of greater than10: 1 and
with its threshold level set just before clipping.
Limiter
6. The PG series includes a Low Frequency filter, which you can use to roll off the extreme
low frequency content below 30 Hz. Most two–way loudspeakers do not produce a
usable frequency response under 30 Hz, so if you set the Low Frequency filter to the “ON”
position, the amplifier will run cooler and more efficiently. We recommend setting the Low
Frequency filter to “ON”for most all applications except when using the amplifier to power
a subwoofer.
Low Frequency Filter
7. On the front panel of the PG Series, turn both Channel input controls fully
counterclockwise (to their “MIN”setting). Then connect the supplied heavy-gauge 3-pin
“IEC”cable to the rear panel IEC connector and to any grounded AC socket.
Because of the relay protection circuitry built into the PG Series, you can even plug it into
the same power strip that other audio devices (such as a mixing console) are connected to.
You can then turn on all devices at once with the single power strip on-off switch, with no
danger of damaging connected speakers by generating “thumps.”
Channel Input control
Protection LED
8. Press the front panel Power switch in order to turn on the PG Series. The Power LED will
light and the Protection LED will go on. After approximately five seconds, the Protection
LED will go off (you’ll hear a click when this occurs).
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Setting Up and Using Your PG Series
9. Apply an input signal to the PG Series at or about +4dBu (if sending signal from a mixer,
drive the output meters at approximately 0 vu). While the input signal is present, slowly raise
the Channel Input controls until the desired sound level is achieved. The SIGNAL and CLIP LED
indicators next to each Channel input control will show you the continuous power output of
the PG Series as signal is being passed. For the best signal-to-noise ratio, the PG Series should
normally be run with the Channel Input controls at or near maximum (fully clockwise, at the
“MAX”position) and the CLIP segments should light occasionally (but not frequently) during
peak levels. If you are using a mixer that has a master output level control (sometimes called
“control room level”), use it to attenuate the signal as necessary to achieve the desired speaker
level.
Three-segment LED meter
NOTE: If you are operating the PG amplifier at high power levels for long durations in fixed
installations, you may consider switching the operating voltage to 220 volts. A licensed and insured
electrician and/or technician should perform this modification.
If you encounter difficulty with any aspect of setting up or using your PG Series, contact your
local Samson dealer. If purchased in the United States, you can call Samson Technical Support
(1-800-372-6766) between 9 AM and 5 PM EST.
The PG Series Protection Circuitry
As noted in the “Guided Tour”section of this manual, the PG Series front-panel Protect
LED indicates the activity of the relay speaker connection circuitry. When the Protect LED is
lit, this circuitry is active, and all connected speakers are muted (provided with no signal), thus
protecting them and preventing any audible “thump”from occurring.
The following conditions will cause the Protect LED to go on:
Protect LED
• Initial power-up: For approximately five seconds after initial power-up, the protection circuit-
ry is activated and the speaker outputs are muted. If everything is operating normally, you will
hear an audible click at the conclusion of this brief period, as the protection circuitry is deacti-
vated and the PG Series begins delivering signal to connected speakers (at which point you’ll
hear a click). It is normal for the Protection LED to fade gradually after the amplifier is powered
off
WARNING: If the Protect LED fails to go out (and you fail to hear the accompanying audi-
ble click) approximately five seconds after power-up, turn the PG Series off immediately
and check all external devices and wiring for possible shorts or other defects.
• Overheating: A temperature sensing device in the PG Series will cause the protection circuitry
to be activated (and the Protection LED to go on) whenever the operating temperature of the
unit rises above a safe level. To guard against this problem, make sure the PG Series receives
adequate ventilation on all sides and that both the front and rear panels are unobstructed.
• Severe overcurrent conditions: This occurs whenever the signal being output from the PG
Series rises to a level above 20% THD (Total Harmonic Distortion).
• Shorted speaker cables: This will occur if, due to faulty wiring, the hot and ground signals
being output by the PG Series are shorted to one another.
• Output impedance drops below 2 ohms: This can occur if the PG Series is connected to inappro-
priate speaker systems (see the “Setting Up and Using Your PG Series”section on page 7 in this
manual for more information).
• DC voltage detected at speaker output: The most likely cause of this is an internal failure.
In general, any time the Protect LED lights up (other than during the approximately five sec-
onds following initial power-up), there is reason to be concerned. If this occurs, turn the PG
Series off immediately and carefully check all wiring and external devices in order to locate and
correct the condition that caused the LED to light up in the first place.
If you encounter difficulty with any aspect of setting up or using your PG Series, contact your
local Samson dealer. If purchased in the United States, you can call Samson Technical Support
(1-800-372-6766) between 9 AM and 5 PM EST.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Bridge and Parallel Modes
The PG Series provides a rear-panel switch that allows it to be used in either Stereo,
Bridge or Parallel mode. When this switch is placed in the “STEREO” (center) position,
the PG Series functions as a true stereo amplifier, where both of the two independent
amplifier channels (Channel 1 and Channel 2) can receive different input signals and
produce independent output signals. However, when the switch is placed in the
“Bridge”(right) position, the Channel 1 inputs signal is routed to both power ampli-
fiers bridged together, producing a single output signal with mono power ratings of
1000 watts at 8Ω and 2200 watts at 4Ω for the PG2200 and a 1800 watts at 8Ω and
3800 watts at 4Ω for the PG3800.
WARNING: Bridge mode is to be used only when the PG Series is connected to a
4 or 8 ohm speaker load. Use of Bridge mode with speaker loads of less than 4
ohms can result in severe damage to the unit due to excessive heat and current
limiting and will void your warranty!
The illustration on the left shows how this works. In Bridge mode, the polarity
(phase) of the Channel 2 output signal is reversed relative to that of the Channel 1 out-
put signal. Both channels then process the same input signal, with the speaker load
connected so that power is derived from both channels. The effective voltage swing
seen by the load is thus doubled, so that the power output is multiplied by four.
Bridge Mode
INPUT
CHANNEL
1(+) OUTPUT
When using the PG Series in Bridge mode, be sure to connect your loudspeaker as
shown in the illustrations on page 10 (and as silkscreened on the rear panel), with
the red (+) terminal of the Channel 1 output connected to the positive input of the
speaker and the red (+) terminal of the Channel 2 output connected to the negative
input of the speaker.
CHANNEL
2(+) OUTPUT
Do not use the black ground (-) output terminal of either channel (the speaker
load must “float” away from the amplifier chassis).
When the rear panel switch is placed in the left “PARALLEL”position, the PG Series
operates in a unique Parallel mode. In this mode, connect the input signal to Channel
1 only. This signal is then routed to both the Channel 1 and Channel 2 power ampli-
fiers, thus producing a dual mono output, with the following power ratings:
PG2200 2 x 280 Watts at 8Ω, 2 x 500 Watts at 4Ω and 2 x 1000 Watts at 2Ω
PG3800 2 x 560 Watts at 8Ω, 2 x 900 Watts at 4Ω and 2 x 1800 Watts at 2Ω
See pages 10- 11 in this manual for interconnection diagrams when using the PG
Series in Bridge or Parallel modes.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
PG Series Connections
+
-
The illustrations on these two pages show the
required interconnections when using the PG Series
in Stereo, Bridge and Parallel modes. Wiring for
Speakon™ connectors (shown on the right) is indi-
cated where appropriate.
Stereo Mode: (two or four speakers)
SAMSON
SAMSON
MMPL2242
MMPL2242
SAMSON
MMPL2242
MPL2242
MPL2242
MPL2242
MPL2242
MPL2242
MPL2242
-
+
+
-
-
+
+
-
+
-
+
+
+
-
-
-
(2 ohm min)
(2 ohm min)
(2 ohm min)
(2 ohm min)
(4 ohm min)
(4 ohm min) (4 ohm min) (4 ohm min)
Bridge Mode: (single speaker only)
SAMSON
SAMSON
MMPL2242
MMPL2242
MPL2242
MPL2242
MPL2242
MPL2242
Speakon™ wiring:
NOT CONNECTED
1- 1+
NOT CONNECTED
2+ 2-
-
+
+
-
(4 ohm min)
(4 ohm min)
Download from Www.Somanuals.com. All Manuals Search And Download.
8
PG Series Connections
Parallel Mode: (two or four speakers)
SAMSON
MMPL2242
SAMSON
SAMSON
MMPL2242
MMPL2242
MPL2242
MPL2242
MPL2242
MPL2242
MPL2242
MPL2242
-
+
+
-
+
+
-
-
+
-
+
+
+
-
-
-
(4 ohm min)
(4 ohm min) (4 ohm min) (4 ohm min)
(2 ohm min)
(2 ohm min)
(2 ohm min)
(2 ohm min)
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Specifications
POWER SPECIFICATIONS
PG-2200
2 x 280W
2 x 500W
2 x 1000W
1000W
PG-3800
2 x 560W
2 x 900W
2 x 1800W
1800W
Stereo Mode (Both channels driven) 20Hz~20KHz 8 Ohms
4 Ohms
2 Ohms
8 Ohms
4 Ohms
Bridge Mono Mode
20Hz~20kHz
2200W
3800W
ELECTRICAL SPECIFICATIONS
INPUT SENSITIVITY
1.22 V(+4 dBu) 1.15 V(+3.4 dBu)
INPUT IMPEDANCE
10K ohms Unbalanced, 20K ohms Balanced
FREQUENCY RESPONSE
(at 10dB below rated output power)
25 Hz~25 kHz +0/-1 dB -3 dB points: 5 Hz~50 kHz
VOLTAGE GAIN
32dB
34dB
DISTORTION(SMPTE IM)
S/N ratio
<0.03%
100dB
<0.03%
100dB
GENERAL SPECIFICATIONS
PROTECTION
Full short circuit,open circuit,thermal,ultrasonic, and RF protection
stable into reactive or mismatched loads, turn ON/OFF, muting
CONTROLS
Front:AC switch,Input level control for each channel. Rear: mode/
stereo/ parallel/ bridged selector; LP 30Hz filter selector,LIMITER ON/
OFF selector.
INDICATORS
PROTECTION
CONNECTORS
SIGNAL: 2 green LED;CLIP: 2 red LED; POWER: 1 Blue LED;
1 red LED
INPUT : Active balanced XLR and 1/4"(6.3 mm)TRS
OUTPUT: "Touch-proof" binding posts and Speakon jacks.
Available for 110-120 V or 220~240 V AC, 50/60 Hz
19"(W)x 15.7"(D) x3.5"(H
POWER SUPPLY
DIMENSIONS
483(W)x 400(D) x88.8(H)mm
WEIGHT
PG2200
PG3800
32.50lbs. (14.74kg)
45.2 lbs. (20.55kg)
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 631-784-2201
Download from Www.Somanuals.com. All Manuals Search And Download.
|