QUICK SETUP GUIDE
RF-TVMLPT02
1 Attach the TV brackets
Option 1: Attaching to
a ꢀat mounting
2 Install the wall plate
Option 1: Installing to a wood stud wall
Caution: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts.
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
a. Locate the studs. Verify the center of the stud with an awl or thin nail or use an edge-to-edge stud finder.
b. Level the wall plate (A) and mark hole locations.
C
surface
Thank you for choosing the
Rocketfish RF-TVMLPT02.
The RF-TVMLPT02 TV mount
is designed to support
a TV weighing up to
Attach the left and right TV
brackets (B and C) to the
back of the TV using:
c. Drill pilot holes as illustrated.
d. Align the wall plate (A) with the pilot holes, then place the lag bolt washers (Q) over the holes. Insert the
lag bolts (R) through the washers, then tighten the lag bolt with a socket wrench only until they are pulled
firmly against the wall plate.
The M4/M5 washers (F) and
the M4 x 12 mm screws (D) or
the M5 x 12 mm screws (H).
Or
The M6 washers (M) and
the M6 x 12 mm screws (J) or
the M6 x 20 mm screws (K).
a.
B
or
C
80 lbs. (36.37 kg).
or
M
< 16 mm
(5⁄8 in.)
F
Package contents
A Wall plate (1)
B LeftTV bracket (1)
C RightTV bracket (1)
D H
J K
b.
B
M4 bag
A
D M4 x 12 mm screws (4)
E M4 x 30 mm screws (4)
F M4/M5 washers (8)
G M4/M5 spacers (4)
C
B
Option 2: Attaching to a curved or
irregular mounting surface
c.
M5 bag
A
H M5 x 12 mm screws (4)
Attach the left and right TV brackets (B and C)
to the back of the TV using:
M4 bag
C
I M5 x 30 mm screws (4)
E
F
D
G
The M4/M5 spacers (G), M4/M5 washers (F),
and the M4 x 30 mm screws (E) or M5 x 30 mm
screws (I).
M6 bag
M4 x 12mm
M4 x 30mm
J M6 x 12 mm screws (4)
K M6 x 20 mm screws (4)
L M6 x 35 mm screws (4)
M M6 washers (4)
N M6 spacers (4)
M4/M5
M4/M5
Or
M5 bag
Hex key bag
H
I
The M6 spacers (N), M6 washers (M), and
the M6 x 35 mm screws (L).
d.
O
M5 x 12mm
M5 x 30mm
Note: Use the M4 washers (F) between
the spacers and the bracket with the M4
or M5 screws only.
Hex key bag
O 3⁄16 in. hex key (1)
M6 bag
M
N
K
L
J
75mm
3 in.
M6 x 12mm
M6 x 20mm
M6 x 35mm
Lag bolt bag
N
G or
M6
M
or
F
M6
P Concrete anchors (3)
Q Lag bolt washers (3)
R 5⁄16 in. x 23⁄4 in. lag bolts (3)
F
E I
L
Lag bolt bag
Q
R
B
P
Q
Tools you will need:
• Phillips screw driver
B
• Stud finder
• Awl
• Hammer (Concrete Only)
• ½ in. socket wrench
or
R
C
• Pencil
• 3/16 in. wood drill bit
• 3/8 in. masonry drill bit (Concrete Only)
• Power drill
• Level
• Tape measure
in. x 2 in.
Download from Www.Somanuals.com. All Manuals Search And Download.
|