R-Series
R500 R600 R700
R800 R800C
O w n e r ’ s M a n u a l
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
The manufacturer cannot accept responsibility for damage
caused when the appliance is not used according to the
instructions, or for uses other than those for which it
was intended.
WARNING:
To reduce the risk of fire, electric shock or injury:
• Do not leave appliance when plugged in.
Unplug from outlet when not in use and
before servicing.
• Do not put any object into openings. Do
not use with any opening blocked; keep
free of dust, lint, hair and anything that
may reduce air flow.
• WARNING: ELECTRIC SHOCK COULD
OCCUR IF USED OUTDOORS OR ON
WET SURFACES.
• Keep hair, loose clothing, fingers and all
parts of body away from openings and
moving parts.
• Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches or
hot ashes.
• Use only as described in this manual.
Use only manufacturer’s recommended
attachments.
• Do not use without vacuum bag and/or
filters in place.
• Do not use with damaged cord or plug. If
appliance is not working as it should, has
been dropped, damaged, left outdoors,
or dropped into water, return it to your
Authorized Retailer for service.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or
combustible liquids such as gasoline or
use in areas where they may be present.
• Do not pull or carry by cord, use cord as
a handle, close a door on the cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
• Do not attempt to service the unit while
appliance is plugged in.
• Do not use vacuum to pick up water or
any wet materials.
• Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
• Use extra care when cleaning on stairs. To
avoid injury and damage, vacuum should
remain at base of stairs while in use.
• Do not handle plug or appliance with
wet hands.
SAVE THESE INSTRUCTIONS.
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢁ
Polarization instructions
Power Cord - 2-Wire Polarized
Household models R500, R600, R700 & R800
To reduce the risk of electric shock this product is equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into
the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician
to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Grounding Instructions
Model R800C Only
This vacuum cleaner must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock.
This vacuum cleaner is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
This vacuum cleaner is for use on a nominal 1ꢁ0-volt circuit and has a ground plug
(see illustration). Make sure that the vacuum is connected to an outlet having the same
configuration as the plug. No adapter should be used with this vacuum.
WARNING – Improper connection of
Grounded
Outlet
the equipment-grounding conductor
can result in the risk of electric shock.
Check with a qualified electrician or
service person if you are in doubt
as to whether the outlet is properly
grounded. Do not modify the plug
provided with the vacuum – if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
Grounded
Outlet Box
Grounding
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
Thermal fuse protection
Your Riccar vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector.
This thermal protector is designed to protect your vacuum cleaner from overheating due to
a restriction in airflow (i.e. clogged hose, operating the vacuum without a bag). Should this
situation occur, the thermal fuse protector will safely shut off the vacuum cleaner to avoid
any potential damage.
NOTE: To determine it was the thermal fuse protector that turned off your vacuum
cleaner, please refer to the vacuum cleaner's headlight. If the headlight is on while the motor
is off, then the thermal fuse protector did safely shut down the motor. If both the headlight
and motor are off, then there is some reason other than the thermal protector (i.e. pulled
plug) your vacuum is off.
To reset the thermal fuse:
1. Unplug the vacuum cleaner
ꢁ. Check for problem – over–filled bag, clog in hose, clogged filters, etc.
ꢀ. Correct problem
4. Locate "tripped" fuse – the small white button located on the bottom of the back side of
the main body (roughly one inch to the right of the left wheel)
5. Using a pencil, paper clip or other pointed object, push the reset button in
6. Plug vacuum cleaner in and resume use
Please contact your Authorized Riccar Retailer with any questions.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Description of the vacuum
Handle grip
On/Off switch
(Models R600,
R700, R800,
R800C)
Cord clip
Hose storage hook
(Models R500, R600,
R800, R800C)
Power cord
Stretch hose
Cord storage
hooks
Carrying handle
On/Off switch
(Model R500)
Telescopic
wand
Full bag
indicator light
(Models R700,
R800 and R800C)
Bag compartment
cover
Suction control
dial
Crevice tool
Upholstery/
dusting tool
Headlight
Thermal fuse
reset button
Furniture
guard
Foot pedal release
Self-adjusting nozzle
Riccar Replacement Parts
Genuine Riccar High Flow
Secondary Filter
Part #Bꢁꢁꢁ-0500
HEPA Vacuum Bags
Part #C1ꢀH-6 6 per package
Light Bulbs, Xenon
Part #Aꢀ50-0000
Wedge Base, 0.917amp
T ꢀ 1⁄4 Xenon
Genuine Riccar EcoPure
Vacuum Filter Bags
Part #C1ꢀ-6 6 per package
Vacuum Agitator Belt
Part #Aꢁ0-RꢁP
Post Filter
Part #RF4-ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Operation
Attaching the handle
The vacuum cleaner and the handle are packed
separately.
1. After first removing the handle screw [Fig. 1],
position the handle behind the vacuum cleaner
and level with the top of the unit. Hold the power
cord down and away from the vacuum while the
handle is being attached [Fig. ꢁ]. Make sure that
the switch on the handle is positioned toward
the front of the vacuum cleaner.
Fig. 1
ꢁ. On the bottom of the handle are two “T-shaped”
rails that slide forward onto two guides located
on the top of the vacuum cleaner. Line up the
handle so that the “T” rails will slide into the
guides and push the handle forward [Fig. ꢀ].
ꢀ. Insert the handle screw and tighten securely.
Fig. ꢁ
4. Attach the power cord at the clip located on the
upper cord hook [Fig. 4].
5. Turn the upper cord storage hook to the upright
position and wind the power cord around the
cord storage hooks when storing the vacuum
cleaner.
Fig. ꢀ
Fig. 4
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Operation
On/Off switch
1. To start the vacuum cleaner, flip the ON/OFF
switch (located on the handle on Models R600,
R700, R800 and R800C or on the side of
bag compartment on Model R500) to the ON
position as indicated by “|” on the switch
[Figs. 5 and 6].
Fig. 5
ꢁ. To stop the vacuum cleaner, flip the ON/OFF
switch to the OFF position as indicated by “O”
on the switch.
ꢀ. Turn the vacuum cleaner off before unplugging
from electrical outlet.
Fig. 6
Handle adjustments
The handle can be set to one of three positions:
Upright, Middle or Low. To release the handle,
step on the pedal at the left rear corner of the
vacuum cleaner [Fig. 7].
1. Upright Position: Handle locks in this position
for vacuum cleaner storage [Fig. 7]. The
handle should always be in the upright position
when cleaning tools are used.
Fig. 7
ꢁ. Middle Position: This position is for normal
cleaning [Fig. 8]. While in the middle position,
the front of the nozzle can be raised for
crossing thresholds between rooms by
lowering the handle.
Fig. 8
ꢀ. Low Position: With the handle in the middle
position, press the foot pedal release again
to allow the vacuum to achieve the low
position. This position is used for cleaning
under furniture [Fig. 9].
Download from Www.Somanuals.com. All Manuals Search And DoFwinglo. a9d.
7
Operation
Replacing vacuum bag
Genuine Riccar vacuum bags should
be used for best performance and air filtration.
Always operate the vacuum cleaner with a
vacuum bag installed.
NOTE: If secondary or post filters need to be
replaced, see page 9 before replacing the
vacuum bag.
Fig. 10
1. Remove the used vacuum bag by pulling bag
collar off the bag holder [Fig. 10]. Do not re-use
filled vacuum bags.
ꢁ. Attach the new vacuum bag onto the
bag holder.
ꢀ. Re-insert the tab on bottom edge of bag
compartment cover into the groove on the
bag compartment housing [Fig. 11]. Press it
into place and close the bag compartment
cover tightly.
Fig. 11
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Operation
Replacing secondary filter
The secondary filter protects the motor from
dust and dirt. Before installing a new vacuum
bag, check the filter. Accumulated dirt in the bag
compartment will be collected on this filter and
may restrict motor performance when the filter
becomes dirty.
Fig. 1ꢁ
1. Remove the vacuum bag to access the
secondary filter.
ꢁ. Remove secondary filter from bottom of bag
compartment [Fig. 1ꢁ].
ꢀ. The secondary filter can be washed or replaced.
If washed, make sure filter is completely dry
before reinstalling.
4. Reinstall by sliding filter under bag support
fingers [Fig. 1ꢀ].
Fig. 1ꢀ
Replacing post filter
Your Riccar vacuum cleaner is equipped with an
auxiliary post filter to capture fine dust particles
and purify the air before it exits the machine. It
is important to change the post filter regularly
– approximately every third vacuum bag change,
or as needed.
1. Remove bag compartment cover and locate the
post filter on inner bottom of cover [Fig. 14].
ꢁ. Remove used filter.
Fig. 14
ꢀ. Align slits in new filter over tabs and press
securely into place.
NOTE: Post filters cannot be washed.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Operation
Removing and reinstalling bottom plate
CAUTION: Disconnect the vacuum cleaner
from the electrical outlet before removing the
bottom plate.
1. Depress handle release pedal twice and place
the vacuum cleaner in the low position.
Fig. 15
ꢁ. Turn vacuum cleaner over, exposing the
underside [Fig. 15].
ꢀ. Slide locking latch to the right [Fig. 16].
4. Press tabs inward on each side [Fig. 17] and
pull bottom plate off.
5. Reinstall by placing lower edge of bottom plate
along lower edge of nozzle [Fig. 18]. Snap
plate into place. Slide locking latch to the left to
secure.
Fig. 16
Fig. 17
Fig. 18
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Operation
Replacing headlight bulb
CAUTION: Disconnect the vacuum cleaner from the
electrical outlet before replacing bulb.
1. Remove bottom plate (See “Removing and
reinstalling bottom plate”).
ꢁ. Remove the headlight bracket by pulling upward
on bracket [Fig. 19]. To remove the light bulb, pull
straight out of socket. To install new bulb, simply
push bulb straight into socket for a secure fit.
Reinsert bracket back into nozzle.
Fig. 19
ꢀ. Re-install bottom plate (See "Removing and
reinstalling bottom plate").
Replacing agitator belt
CAUTION: Disconnect the vacuum cleaner from the
electrical outlet before replacing belt.
Fig. ꢁ0
1. Remove bottom plate (See “Removing and reinstalling
bottom plate”). Remove vented support fitting
[Fig. ꢁ0] and belt guard [Fig. ꢁ1].
ꢁ. Take out the agitator assembly and remove worn or
broken belt from agitator pulley and motor drive
shaft [Fig. ꢁ1].
ꢀ. Loop new belt around the agitator pulley and the
motor drive shaft and re-insert the agitator assembly
back into the housing. Turn the agitator assembly
by hand, making sure the belt is not twisted and all
rotating parts move smoothly [Fig. ꢁꢁ].
Fig. ꢁ1
4. Re-insert the vented support fitting and belt guard,
making sure that they are in place before fastening
the bottom plate to the two ribs at the front of the
housing. Re-install bottom plate.
NOTE: To ensure maximum cleaning efficiency, the
condition of the belt should be checked regularly. If belt
is stretched, cracked or if excessive slipping is occurring,
replace the belt.
Fig. ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Operation
Unclogging nozzle and hose
CAUTION: Disconnect the vacuum cleaner from
the electrical outlet before cleaning nozzle housing.
The nozzle hose, located on the back of the
vacuum, carries the dirt from the nozzle to the
vacuum bag. The hose also functions as the
attachment cleaning hose. First check to see
that a bag is installed or that the bag has not
broken open.
Fig. ꢁꢀ
If the hose should become clogged:
1. Pull out and turn the lid of the cleaning
attachment opening. Remove the clog or
blockage [Fig. ꢁꢀ].
ꢁ. Remove hose cuff from nozzle inlet and check
for clog [Fig. ꢁ4].
Fig. ꢁ4
ꢀ. Turn unit over and remove bottom plate (See
“Removing and re-installing bottom plate”).
Check nozzle inlet tube for obstructions [Fig.
ꢁ5]. Clear tube and re-install bottom plate.
Fig. ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢁ
Operation
Full bag indicator light
Models R700, R800 and R800C
The warning light is located on top of the bag
compartment (see Fig. ꢁ6). The light will trigger
if the vacuum bag is full or if there is a clog in the
vacuum cleaner. If the light indicator turns on,
check the vacuum bag. If it is not full, check the
vacuum cleaner for clogs by inspecting the
agitator area (see “Removing and re-installing
bottom plate”), hose and/or attachment inlet.
Fig. ꢁ6
Please disregard the indicator light during
attachment cleaning. The light is designed to
indicate air flow restriction during carpet cleaning.
When using cleaning attachments, the indicator
will light periodically due to normal attachment air
flow restrictions.
Edge cleaning
The edge cleaning feature provides for improved
cleaning of carpets near walls and stationary
furniture. For maximum edge cleaning, place the
right side of the nozzle against the wall or furniture.
Automatic carpet height adjustment
Your Riccar upright vacuum cleaner is designed
with an Automatic Self-Adjusting Rug Nozzle.
No manual adjustments are required. The height
of the rug nozzle is instantly and automatically
adjusted to carpet pile height. This self adjusting
feature allows the rug nozzle to float evenly over all
carpet pile surfaces.
Download from Www.Somanuals.com. All Manuals Search And Download.
1ꢀ
Tools
FastTask™ cleaning tools
(Models R500, R600, R800 and R800C)
Select models are equipped with FastTask™ cleaning
tools which include a combination upholstery/dusting
tool, crevice tool and stretch hose.
1. Remove the telescopic wand from the body of the
vacuum [Fig. ꢁ7]. Unlock wand collar (located on
end of wand) [Fig. ꢁ8], extend wand and re-lock
the wand collar.
NOTE: Wand collar locking rotation is marked with
arrows on wand. Wand collar lock and unlock
functions require only 1/ꢁ turn of collar.
ꢁ. Remove the crevice tool on left side of vacuum
cleaner and insert into end of wand [Fig. ꢁ9]. The
vacuum is now ready for crevice cleaning.
Fig. ꢁ7
ꢀ. Insert the combination upholstery/dusting tool
(located conveniently in the back of the bag
compartment) onto the end of the crevice tool
[Fig. ꢀ0]. The combination tool can also be inserted
directly onto the telescopic wand. To convert the
dusting brush to an upholstery tool, simply slide
the brush off [Fig. ꢀ1].
Fig. ꢁ8
Fig. ꢁ9
Fig. ꢀ0
Fig. ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Tools
Optional cleaning tools
All Riccar upright vacuum cleaners offer an attachment port that enables you to insert
optional cleaning tools (available through your Riccar Retailer). Should you have carpeted
stairs, for example, it is highly recommended to use one of the two kits pictured, since each
offers either a 1ꢁ- or 15-foot hose for safe stair cleaning. These kits are effective overall
cleaning tools to address some of the hard to reach areas of your home or car. Talk to your
Riccar Retailer to see which tools might be beneficial for your home.
For models without on-board tools
Deluxe Attachment Set (Fig. ꢀꢁ)
For models with on-board tools
Attachment Set (Fig. ꢀꢀ)
1. 1ꢁ-foot hose
ꢁ. Curved wand
ꢀ. Extension wand (ꢁ pieces)
4. Dusting brush
1. 15-foot hose
ꢁ. Curved wand
ꢀ. Deluxe floor brush
5. Crevice tool
6. Upholstery tool
7. Upholstery brush insert
8. Deluxe floor brush
Fig. ꢀꢀ
Fig. ꢀꢁ
1. How to connect the hose assembly to the vacuum
cleaner: Pull out and open the suction control dial by
turning the lid located on the back of the vacuum cleaner.
Insert the soft, rubber end of the hose assembly into the
cleaning attachment opening. Push in while twisting the
hose end to ensure the hose is fastened securely (Fig. ꢀ4).
Fig. ꢀ4
ꢁ. How to connect the tool: You can connect any of the
cleaning tools to the end of the extension wand(s) or
curved wand and twist for a secure fit. To remove the
cleaning tool from the extension wand(s) or curved wand,
simply twist and pull apart.
WARNING: There is no way to turn this vacuum’s brushroll off. Therefore, when using the cleaning
tools it is important to keep your Riccar vacuum from running in the same spot for a period of time, as
carpet or flooring damage could result. If you need to keep the vacuum in the same spot for a period
of time, such as at the base of the stairs when cleaning the stairs, place something, like a flattened
cardboard box, under the vacuum to prevent damage to the floor.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Owner’s information (keep this for your records)
The model and serial number of this product may be found on the back side of the unit. You
should note the model and serial number of your unit in the spaces provided below, and
retain this book as a permanent record of your purchase.
Date of purchase ____________________________________________________
Serial number _______________________________________________________
Model number ______________________________________________________
Purchased from:
Store name _______________________________________________________
Address
City, State, Zip ______________________________________________________
Telephone _______________________________________________________
_______________________________________________________
Your Riccar vacuum cleaner is a product of high quality materials and superior workmanship.
Your new Riccar vacuum cleaner will work on carpets, floors and for many other cleaning
needs in your home. We urge you to read these operating instructions carefully before you
use this vacuum cleaner, in order to obtain the full performance and satisfaction it can
offer you.
For Best Performance
•
Before you plug in your Riccar vacuum cleaner, make sure that the voltage indicated
on the rating plate (located near the bottom on the back of the vacuum) is the same
as your local supply.
•
•
•
Keep machine and all accessories clean and in good operating condition.
Store machine carefully in a dry area.
Always use genuine Riccar vacuum bags and filters. Use of other products may result
in poor cleaning or filtration performance. Riccar filtration products are designed for
maximum performance.
•
•
•
Have machine checked periodically by an Authorized Riccar Vacuum Service Center.
Use only Riccar Vacuum Cleaner Authorized Service Centers for parts and service.
For optimum cleaning performance and safety, follow your Owner’s Manual and keep it
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Warranty
What is Covered:
This warranty covers any defects in material and workmanship in your new
Riccar vacuum.
How Long Coverage Lasts:
Warranty coverage for Riccar R-Series household model vacuums lasts three
years and one year for R-Series commercial model vacuums. Household
models used commercially are only warranted for 90 days.
What is Not Covered:
• Damage to the vacuum which occurs from neglect, abuse, alterations,
accident, misuse or improper maintenance.
• Normal replacement items: agitator brushes, belts, light bulbs, disposable
bags and disposable filters.
What Riccar Will Do:
This warranty provides, at no cost to you, all labor and parts to place this
vacuum in correct operating condition during the warranted period.
How to Get Service:
Warranty service can only be obtained by presenting the vacuum to an
Authorized Riccar Retailer. A proof-of-purchase and product serial number
will be required before service is rendered. To locate your nearest Riccar
Retailer, please call 1-888-6-RICCAR or visit the Riccar website at
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER
WARRANTIES WHETHER WRITTEN, ORAL, EXPRESSED OR IMPLIED,
(INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE). THIS WARRANTY DISCLAIMS LIABILITY FOR
INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
How State Law Applies:
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
|