Owners &
P48-2 Gas Fireplace
Installation Manual
MODELS: P48-NG2 Natural Gas P48-LP2 Propane
WARNING:
FOR YOUR SAFETY
Iftheinformationintheseinstructionsarenotfollowedexactly, What to do if you smell gas:
a fire or explosion may result causing property damage,
personal injury or loss of life.
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
03/05/08
918-524a
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Optional Bay Door.......................................................35
Optional Bay Trim........................................................35
Bay Louvers ................................................................35
Optional Finishing Trim................................................36
Double Screen Door ...................................................36
Optional Remote Control.............................................37
Optional Wall Switch....................................................37
Optional Wall Thermostat ...........................................37
Wiring Diagrams .........................................................38
Installing The Optional Fan..........................................40
To Remove the Fan .............................................40
SAFETY LABEL
Copy of Safety Decal.....................................................4
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)............................5
INSTALLATION
OPERATING INSTRUCTIONS
Important Message ......................................................6
Before You Start ............................................................6
General Safety Information ...........................................6
Installation Checklist......................................................6
Manufactured Mobile Home Additional Requirements ..7
Locating Your Gas Fireplace .........................................7
Unit Specifications.........................................................7
Heatwave Optional Duct System Kit .............................7
Optional Heat Release Kit ............................................7
Hearth............................................................................7
Clearances ....................................................................8
Mantels..........................................................................9
Mantel Leg Clearances .................................................9
Framing & Finishing ....................................................10
Unit Assembly Prior To Installation ..............................11
Top Standoff Assembly ........................................11
Top Facing Support and Side Nailing Strips ........11
Venting Introduction.....................................................11
Exterior Vent Termination Requirements.....................12
Venting Arrangements ................................................13
Horizontal Termination.........................................13
Simpson Dura-vent Venting.................................14
Simpson Dura-vent Venting Components List.....14
5” x 8” Rigid Pipe Cross Reference Chart...................15
Vertical Terminations...........................................21
Unit Installation with Horizontal Termination................23
Unit Installation with Vertical Termination ....................24
System Data ...............................................................26
High Elevation .............................................................26
Gas Line Installation....................................................26
Pilot Adjustment...........................................................26
Gas Pipe Pressure Testing..........................................26
S.I.T. Valve Description................................................26
Conversion Kit from NG to LPG Part #372-969 .........27
Brick Panels Installation ..............................................30
Log Set Installation......................................................31
Standard Flush Door ...................................................34
Flush Louvers..............................................................34
Optional Flush Trim .....................................................34
Operating Instructions .................................................41
Shutdown Procedure...................................................41
First Fire ......................................................................41
Lighting Procedure ......................................................41
Aeration Adjustment ....................................................41
Normal Operating Sounds of Gas Appliances.............42
MAINTENANCE
Maintenance Instructions ............................................43
General Vent Maintenance..........................................43
Log Replacement ........................................................43
Thermopile / Thermocouple.........................................43
Glass Gasket...............................................................43
Gold-Plated Louvers & Trim ........................................43
Door Glass ..................................................................44
Glass Replacement .............................................44
Bay Glass Replacement ......................................44
Installing Valve.............................................................44
Removing Valve...........................................................45
PARTS LIST
Main Assembly ............................................................46
Burner & Log Assembly...............................................48
Flush Door & Louvers..................................................49
Bay Front & Louvers....................................................50
WARRANTY
Warranty......................................................................51
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL
Thisisacopyofthelabelthataccompanieseach
P48-NG2 and P48-LP2 Zero Clearance Direct
Vent Gas Fireplace. We have printed a copy of
the contents here for your review. The safety
label is located on the front inside base of the
unit, visible when the bottom louver is open.
NOTE: Regency® units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA720 and a CO alarm
withbatterybackupinthesameroomwhere
the gas appliance is installed.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
4
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
12) Installationandanyrepairstothisappliance
should be done by an authorized service
person.Aprofessionalservicepersonshould
be called to inspect this appliance annually.
Make it a practice to have all of your gas
appliances checked annually.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM AS
THE APPLIANCE.
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The P48-NG2/P48-LP2 Direct Vent Fireplace
must be installed in accordance with these
instructions. Carefully read all the instructions
in this manual first. Consult the "authority
having jurisdiction" to determine the need for
a permit prior to starting the installation. It is
the responsibility of the installer to ensure
this fireplace is installed in compliance with
manufacturers instructions and all applicable
codes.
CLOTHINGOROTHERFLAMMABLE
MATERIALSHOULDNOTBEPLACED
ON OR NEAR THE APPLIANCE.
13) Do not slam shut or strike the glass door.
14) Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
15) The appliance area must be kept clear and
free of combustible materials, (gases and
other flammable vapours and liquids).
GENERAL SAFETY
INFORMATION
1) The appliance installation must conform
with local codes or, in the absence of local
codes,withthecurrentCanadianorNational
Gas Codes, CAN1-B149 or ANSI Z223.1
Installation Codes.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of
the following:
2) The appliance when installed, must be
electrically grounded in accordance with
localcodes, orintheabsenceoflocalcodes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
INSTALLATION
CHECKLIST
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THE APPLIANCE
BE KEPT CLEAN.
1) Locate appliance
3) See general construction and assembly
instructions. The appliance and vent should
be enclosed.
a) Room location (Refer to "Locating Your
Gas fireplace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) MantleClearances(Referto"Combustible
Mantel Clearances" section)
d) Framing&FinishingRequirements(Refer
to "Framing & Finishing" section)
e) Venting Requirements (Refer to
"Venting" section)
4) This appliance must be connected to the
specified vent and termination cap to the
outsideofthebuildingenvelope. Nevervent
to another room or inside a building. Make
sure that the vent is fitted as per Venting
instructions.
5) Inspect the venting system annually for
2) Assemble Top Standoffs and Top Facing
Support and Side Nailing Strips (Refer to
"UnitAssemblyPriortoInstallation). NOTE:
Must be done before installing unit into
place.
blockage and any signs of deterioration.
6) Venting terminals shall not be recessed into
a wall or siding.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
7) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
3) Installvent(Referto"Venting Arrangement"
sections).
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
4) Make gas and electrical connections. Test
the pilot. Must be as per diagram (Refer to
"Pilot Adjustment " section).
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE
A SERIOUS HOUSE FIRE.
9) Wearglovesandsafetyglassesforprotection
Convert to propane if desired (Refer to
"Conversion from NG to LPG" section).
while doing required maintenance.
10) Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULDSTAYAWAYTOAVOIDBURNS
OR CLOTHING IGNITION.
5) Test Gas Pressure. (Refer to "Gas Pipe
Pressure Testing" section)
11) Under no circumstances should this
appliancebemodified. Partsthathavetobe
removed for servicing should be replaced
prior to operating this appliance.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
6
INSTALLATION
6) Install standard and optional features. Refer
5) This appliance is Listed for bedroom
installationswhenusedwithaListedMillivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
UNIT SPECIFICATIONS
to the following sections:
a)
b)
c)
d)
e)
f)
g)
h)
i)
Brick Panels Installation
Log Set Installation
Standard Flush Door
Flush Louvers
Flush Trim
6) The P48-2 Direct Vent Gas Fireplace is
approvedforalcoveinstallations,whichmeet
the clearances listed on this page.
Bay Door
Bay Trim
Bay Louvers
7) Werecommendthatyouplanyourinstallation
on paper using exact measurements for
clearances and floor protection before
actually installing this appliance. Have an
authorized inspector, dealer, or installer
review your plans before installation.
Finishing trim
j)
k)
l)
Double Screen Door
Remote Control
Wall Switch
m)
n)
Wall Thermostat
Installing the Fan
Note: For vent terminations see "Exterior
Vent Termination Locations"
section.
11) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label 51,000 (NG)
Btu/h, 48,000 (LP) Btu/h) after burning
appliance for 15 minutes.
HEATWAVE
OPTIONAL
LOCATING YOUR
GAS FIREPLACE
1) Whenselectingalocationforyourfireplace,
ensure that the clearances outlined on this
page are met.
DUCT SYSTEM KIT
#946-556
2) Ifrequired,adjustingtheprimaryairtoensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing
warmairfromthefireplacetoremotelocationsin
the same room or other rooms in your home.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
2) Provide adequate clearances for
servicing.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be
operated at one time. This includes the internal
blower option as well.
3) The appliance must be installed on a flat,
solid,continuoussurface(e.g.wood,metal,
concrete).Thismaybethefloor,orraisedup
on a platform to enhance its visual impact.
If the appliance is going to be installed
on carpeting, combustible linoleum tile or
othercombustiblematerialotherthanwood
flooring, theappliancemustbeinstalledon
a metal or wood panel extending the full
width and depth of the appliance.
MANUFACTURED
MOBILE HOME
ADDITIONAL
OPTIONAL
HEAT RELEASE KIT
#946-570
REQUIREMENTS
1) Ensure that structural members are not cut
The Heat Release Kit expels warm air from
the fireplace to the outside of the building,
allowing the fireplace to be operated with less
heat entering the room. The kit may be used on
either the left or right side.
or weakened during installation.
4) The P48-2 Direct Vent Gas Fireplace
can be installed in a recessed position or
framed out into the room as in A, B, C, D.
See Diagram 1.
2) Ensure proper grounding using the #8
ground lug provided. See "Wiring Diagram"
section.
Diagram 1
HEARTH
Ahearth is not mandatory, but is recommended
for aesthetics and for added safety.
A) Flat on Wall
B) Flat on Wall Corner
C) Recessed into
Wall/Alcove
D) Corner
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
7
INSTALLATION
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest
importance that this fireplace and vent system be installed only in accordance with these instructions.
Clearance to Combustibles from:
Caution Requirements
Back
Side
0"
0"
0"
(0mm)
(0mm)
(0mm)
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.
Floor
Minimum Clearance from Top of Front Facing:
Mantel
Ceiling
min. 8" (203mm)
39"
(990mm) from top of front facing
above louvers.
Side Wall:
6"
(152mm)
Horizontal Vent Clearances:
Top
2-1/2"
1-1/2"
1-1/2"
(64mm)
(38mm)
(38mm)
Side
Bottom
Vertical Vent Clearances:
1-1/4"
(32mm)
Alcove Clearances:
Max. Depth 36"
(914mm)
(1524mm)
(2032mm)
Min. Width
60"
Min. Height 80"
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials
are not adhered to. It is of greatest importance that this
fireplace and vent system be installed only in
accordance with these instructions.
The HeatWave Duct Kit
and the Heat Release Kit
have different clearance
and framin requirements,
check the HeatWave and
Heat Release manual for
details.
Heat Release Kit
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
8
INSTALLATION
MANTELS
Because of the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from louver are shown
in the diagram below.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible
board.
This drawing is to scale at 1:6 (one inch = 6
inches)
Mantelcanbeinstalledanywhereinshadedarea
using the above scale for units with the Flush
Front and with the optional Bay Front.
Note: Ensure the paint that is used
on the mantel and the facing is
"heat resistant" or the paint may
discolour.
MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram:
Maximum
1-1/2" projection at 3"
minimum clearance.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
9
INSTALLATION
FRAMING & FINISHING
1) Determine the total thickness of facing material (eg. drywall plus
ceramic tiles) to allow the finished surface to be flush with the front
of the unit. Total facing thickness can vary from 1/2" (13mm) to
1-1/4" (32mm) thick.
2) Frame in the enclosure for the unit with framing material. The framed
opening for the assembled kit is 47-1/2" high x 48-1/2" wide x 26-1/4"
deep (1207mm H x 1232mm W x 667mm D). See Diagram 1. See
important note below when installing with any veritical venting off of
the top.
Diagram 1
Note: 43" (1092mm) is the minimum height for flex termination and
Simpson Dura-Vent terminations.
3) For exterior walls, insulate the enclosure to the same degree as
the rest of the house, apply vapour barrier and drywall, as per local
installation codes. (Do not insulate the fireplace itself.)
4) The unit does not have to be completely enclosed in a chase. The
clearanceontopoftheunitfromthetopstandoffsis0"socombustible
building materials can be laid directly on top of the standoffs. You
mustmaintainclearancesfromtheventtocombustiblematerials:See
"Clearances" section. Combustible materials can be laid against the
side and back standoffs and the stove base.
The HeatWave Duct Kit has different
clearance and framing requirements,
check the HeatWave manual for details.
IMPORTANT
When installing the unit with any vertical venting off the top of the
unit as shown, the minimum framing depth changes accordingly.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
10
INSTALLATION
TOP FACING SUPPORT AND
SIDE NAILING STRIPS
UNIT ASSEMBLY
PRIOR TO
"C" Screw Position:
Forafacingmaterialdepthof1-1/4"(32mm),
the top facing support must be reversed.
Determine the total thickness of facing material
(e.g. drywall plus ceramic tiles) to allow the
finished surface to be flush with the front of the
unit. Total facing thickness can vary from 1/2"
(13mm) to 1-1/4" (32mm) thick.
INSTALLATION
TheTopFacingSupport, theSideNailingStrips
and the 2 Top Standoffs must be correctly
positioned and attached to the top before unit
is slipped into position.
TheTopFacingSupport&SideNailingStripscan
be mounted in 3 different positions depending
on the thickness of the facing material.
TOP STANDOFF ASSEMBLY
The top standoffs are shipped in a flat position
and must be folded into shape and attached.
Screw
Facing Material Depth
1) Remove the standoffs from the fireplace
top.
Position
A
B
1/2" / 13mm
7/8" / 22mm
1-1/4" / 32mm
2) Takeeachstandoffandbendintothecorrect
shape. Bend up at the bend lines until the
screw holes in the standoff and the pre-
punched screw holes on the fireplace top
line up.
2) Use the same screw hole position for the
Side Nailing Strips as was used for the Top
Facing Support. Attach each side nailing
strip using 3 screws.
C*
* For "C" screw position the top facing support
is reversed.
3) Attach the standoff securely to the top
with 2 screws per standoff (on opposite
corners).
1) Mount Top Facing Support using the 3
supplied screws into the three pre-punched
screw holes on the top front of the unit. Use
hole positionsA, B, or C depending on your
facing depth.
VENTING
INTRODUCTION
The P48-2 uses the "balanced flue" technology
CoAxial system. The inner liner vents products
of combustion to the outside while the outer
liner draws outside combustion air into the
combustion chamber thereby eliminating the
needtouseheatedroomairforcombustionand
losing warm room air up the chimney.
Note: These flue pipes must not be
connected to any other appliance.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Eachdirectventgasappliancemustuseit'sown
separate vent system. Common vent systems
are prohibited.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
11
INSTALLATION
EXTERIOR VENT TERMINATION REQUIREMENTS
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
12
INSTALLATION
VENTING ARRANGEMENTS
HORIZONTAL TERMINATION
Regency® Direct Vent System (Flex)
These venting systems, in combination with the P48-2 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by
Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent
Termination Locations" section.
Regency® Direct Vent (Flex) System
Termination Kit (Part# 946-618) includes all
the parts needed to install the P48-2 with a
maximum run of 4 feet.
1) 8" dia. flexible liner (6 ft. length)
2) 5" dia. flexible liner (6 ft. length)
3) spring spacers (4)
4) thimble (2)
5) AstroCap XL termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" Drill Point,
Stainless Steel (4)
10) vinyl siding standoff
Iflongerrunsareneeded,theRegency® Direct
Ventsystem(Flex)Part#946-616includesall
the parts needed to install the P48-2 with a
maximum 10' run.
1) 8" dia. flexible liner (10 ft. length)
2) 5" dia. flexible liner (10 ft. length)
3) spring spacers (7)
4) thimble (2)
5) AstroCap XL termination cap (1)
6) screws (12)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" Drill Point,
Stainless Steel (4)
10) vinyl siding standoff
Notes:
1) Liner sections should be continuous without any joints or seams.
2) Only Flex pipe purchased from Regency® may be used for Flex installations.
3) If you are installing the P48-2 into a Regency® Mantel Kit, use the minimum horizontal vent height (centre-line of 43"). Remember to
include the mantel base in your calculations and to maintain the 2-1/2" clearance to the underside of the mantel top.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
13
INSTALLATION
SIMPSON DURA-VENT VENTING
Horizontal or Vertical Terminations
The Simpson Dura-Vent Direct Vent System offers a complete line of component parts for installation of both horizontal and vertical installations. Many
items are offered in decorative black, as well as galvanized finish. We recommend using the galvanized finish for installation with the P48-2.
The minimum components required for a basic
horizontal termination are:
1
1
1
1
1
Horizontal Termination Cap
45o Elbow
Flue Adaptor
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
Wall thickness is measured from the back
standoffs to the inside mounting surface of
termination cap. For siding other than vinyl
furring strips may be used, instead of the vinyl
siding standoff, to create a level surface to
mount the vent terminal. The Terminal must
not be recessed into siding. Measure the wall
thickness including furring strips.
If a Vinyl Siding Standoff is required (it must
be used with vinyl siding), measure to outside
surface of wall without siding and add 2
inches.
Flat Wall Installation
Alternate
Horizontal Termination
Caps
Wall Thickness
Vent Length
(inches)
4" - 5-1/2"
7" - 8-1/2"
10" - 1-1/2"
9" - 14-1/2"
15" - 23-1/2"
Required (in.)
none
6"
9"
12"
11" - 14-5/8" Adj.
Pipe
SIMPSON DURA-VENT VENTING
COMPONENTS LIST
Part # Description
Part # Description
Part # Description
1245
45O Elbow Galv.
1281 Snorkel-36" Rise Term.Cap
1240 Wall Thimble-Suprt/Box
1241 Cathdrl/Clng-Sprt/Box
3951 Brass Trim for Wall Thimble/
Ceiling Support
1208B 6" Pipe Length-Black
1207B 9" Pipe Length-Black
1206 12" Pipe Length Galv.
1206B 12" Pipe Length-Black
1204 24" Pipe Length Galv.
1204B 24" Pipe Length-Black
1203 36" Pipe Length Galv.
1203B 36" Pipe Length-Black
1202 48" Pipe Length Galv.
1202B 48" Pipe Length-Black
1211B 11"-14 5/8" Adj./P/L-Black
1217B 17"- 24" Adj. Length Black
1245B 45O Elbow-Black
1245G 45O Elbow-Swivel Galv.
1245BG 45O Elbow-Swivel-Black
1290
90O Elbow Galv.
1290B 90O Elbow-Black
1263 Firestop Spacer
1290G 90O Elbow-Swivel Galv.
1290BG 90O Elbow-Swivel-Black
1243 Flashing 0/12-6/12
1243S Flashing 7/12-12/12
1253 Storm Collar
1250 Vinyl Siding Standoff
1288 Wall Strap
1247 Wall Thimble
1291 High Wind Term. Cap (Vertical Only)
1285 Horiz.Sq.HighWind Trm.Cap (Only)
1282 Snorkel-14" Rise Term.Cap
Parts not supplied by Dura-Vent
770-994 Rigid Pipe Adaptor
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
14
INSTALLATION
5” X 8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Simpson
Simpson
Metal-Fab®
Sure Seal
Selkirk
Direct Vent GS®
Discontinued
Description
Direct Vent Pro®
Direct-Temp™
6” Pipe Length, Galvanized
6” Pipe Length, Black
58DVA-06
1208
5DT-6
5D6
58DVA-06B
58DVA-09
1208B
1207
5DT-6B
5DT-9
5D6B
N/A
9” Pipe Length, Galvanized
9” Pipe Length, Black
58DVA-09B
58DVA-12
1207B
1206
5DT-9B
5DT-12
5DT-12B
5DT-18
5DT-18B
5DT-24
5DT-24B
5DT-36
5DT-36B
5DT-48
5DT-48B
N/A
N/A
12” Pipe Length, Galvanized
12” Pipe Length, Black
5D12
5D12B
5D18
5D18B
5D24
5D24B
5D36
5D36B
5D48
5D48B
N/A
58DVA-12B
58DVA-18
1206B
18” Pipe Length, Galvanized
18” Pipe Length, Black
58DVA-18
58DVA-18B - N/A from FPI
58DVA-18B - N/A from FPI
24” Pipe Length, Galvanized
24” Pipe Length, Black
58DVA-24
1204
58DVA-24B
58DVA-36
1204B
36” Pipe Length, Galvanized
36” Pipe Length, Black
1203
58DVA-36B
58DVA-48
1203B
48” Pipe Length, Galvanized
48” Pipe Length, Black
1202
58DVA-48B
58DVA-60
1202B
60” Pipe Length, Galvanized
60” Pipe Length, Black
58DVA-60
58DVA-60B - N/A from FPI
58DVA-60B - N/A from FPI
N/A
N/A
Adjustable Length 3”-10”, Galvanized
Adjustable Length 3”-10”, Black
Adjustable Length 11”-14”, Galvanized
Adjustable Length 11”-14”, Black
Adjustable Length 17”-24”, Galvanized
Adjustable Length 17”-24”, Black
Extension Pipe 8-1/2”, Galvanized
Extension Pipe 8-1/2”, Black
N/A
N/A
N/A
5DAL
5DALB
N/A
N/A
N/A
N/A
Disc - See 58DV-08A
Disc - See 58DV-08AB
Disc - See 58DV-16A
Disc - See 58DV-16AB
58DVA-08A - N/A from FPI
Disc - See 58DV-08A
Disc - See 58DV-08AB
Disc - See 58DV-16A
Disc - See 58DV-16AB
58DVA-08A - N/A from FPI
5DT-AJ
5DT-AJB
N/A
N/A
N/A
N/A
N/A
N/A
N/A
58DVA-08AB
58DVA-08AB
N/A
N/A
58DVA-16A - N/A from FPI
58DVA-16A - N/A from FPI
Extension Pipe 16”, Galvanized
Extension Pipe 16”, Black
N/A
N/A
58DVA-16AB
58DVA-16AB
N/A
N/A
45º Elbow, Galvanized
45º Elbow, Black
58DVA-E45
1245
5DT-EL45
5DT-EL45B
N/A
N/A
58DVA-E45B
Disc - See 58DVA-E45
Disc - See 58DVA-E45B
58DVA-E90
1245B
N/A
45º Elbow, Swivel, Galvanized
45º Elbow, Swivel, Black
90º Elbow, Galvanized
90º Elbow, Black
1245G
5D45L
5D45LB
N/A
1245BG
N/A
58DVA-E90
58DVA-E90B
Disc - See 58DVA-E90
Disc - See 58DVA-E90B
N/A
5DT-EL90S
5DT-EL90SB
N/A
58DVA-E90B
Disc - See 58DVA-E90
Disc - See 58DVA-E90B
N/A
N/A
90º Elbow, Swivel, Galvanized
90º Elbow, Swivel, Black
90º Starter Elbow, Swivel, Galvanized*
Adaptor*
5D90L
5D90LB
5D90A
5DDA
N/A
N/A
N/A
N/A
N/A
Ceiling Support
58DVA-DC
1240
1241
1288
N/A
5DT-CS
5DT-CSS
5DT-WS/B
5DT-OS
5DT-WT
N/A
5DSP
5DRS
5DWS
N/A
Cathedral Support Box
Wall Support/Band
58DVA-CS
58DVA-WS
58DVA-ES - N/A from FPI
58DVA-WT
Offset Support
Wall Thimble, Black
Wall Thimble Support Box/Ceiling Support
Firestop Spacer
1247
N/A
5DWT
N/A
58DVA-DC - N/A from FPI
58DVA-FS
1263
1242
5DT-FS
5DT-TP
5DFS
5DCP
Trim Plate, Black
58DAV-WFS
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
15
INSTALLATION
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Simpson
Simpson
Metal-Fab®
Sure Seal
Selkirk
Direct Vent GS®
Discontinued
Description
Direct Vent Pro®
Direct-Temp™
Round Support / Radiation Sheild
Flat Flashing
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Attic Insulation Shield 12”
58DVA-IS - N/A from FPI
58DVA-IS - N/A from FPI N/A
N/A
Basic Horizontal Termination Kit (A)
Horizontal Termination Kit (B)
Vertical Termination Kit
N/A
N/A
5DT-HKA
5DT-HKB
N/A
N/A
N/A
58DVA-KHA
58DVA-VCH
N/A
1291
5DT-VKC
High Wind Vertical Cap
High Wind Horizontal Cap
Horizontal Square Termination Cap
Vertical Termination Cap
Storm Collar
N/A
N/A
N/A
N/A
DISC.
N/A
1285
1284
N/A
N/A
N/A
5DT-HHC
5DT-HVC
5DT-SC
5DHT
5DVT
5DSC
N/A
58DVA-SC
1253
Adjustable Flashing, 0/12-6/12
Adjustable Flashing, 6/12-12/12
58DVA-F6
1243
5DT-AF6
5DF
58DVA-F12
1243S
5DT-AF12
5DF-12
Vinyl Siding Standoff
58DVA-VSS
N/A
1250
N/A
5DT-VS
5DVS
N/A
Vinyl Siding Shield Plate
5DT-VSP
Snorkel Termination 14”
Snorkel Termination 36”
58DVA-SNK14
N/A
1282
1281
5DT-ST14
5DT-ST36
5DST14
5DST36
Restrictor Disk
58DVA-RD
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Colinear Flex Liner Adapter (3” Ø)
FPI
946-604/P
770-994
Simpson Direct Vent Vent Guard (Optional)
Rigid Pipe Adapter (Must use with all Rigid Piping)
946-623/P
946-506/P
946-625
AstroCap XL Horizontal Cap
Vent Guard (Optional)
Vinyl Siding Standoff - AstroCap XL
*NOTE: When using Metal-Fab Sure Seal Rigid Piping please note that either the Adaptor (5DDA) or 90º Starter Elbow
(5D90A) must be used in conjunction with FPI Rigid Pipe Adaptor (770-994).
L676 & L900 Direct Vent Fireplace
IMPORTANT NOTE
• A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower.
• The Simpson Dura-Vent and Selkirk Direct Temp horizontal termination caps cannot be used in any applications.
• Only the AstroCap XL and Snorkels are certified for horizontal terminations.
Offset Pipe Selection:
Use this table to determine offset pipe lengths.
Forspecificinstructionsordetailsonparticular
venting components please visit the following
websites:
5” x 8” Venting
Pipe Length
Run (X)
Rise (Y)
0”(0mm)
5-11/16”(144mm)
8-13/16”(224mm)
10-15/16”(278mm)
13”(330mm)
15-5/16”(389mm)
18-7/16”(468mm)
20-9/16”(522mm)
22-11/16”(576mm)
31-1/16”(789mm)
39-7/16”(1002mm)
47-7/8”(1216mm)
6”(152mm)
9”(229mm)
12”(305mm)
24”(610mm)
36”(914mm)
48”(1219mm)
L
Y
21-7/16”(697mm)
29-13/16”(757mm)
38-1/4”(972mm)
X
NOTE: Horizontal runs of vent must be level, or have a 1/4 inch rise for every 1 foot of run towards
the termination. Never allow the vent to run downward. This could cause high temperatures and
may present a possible fire hazard.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
16
INSTALLATION
SIMPSON DURA-VENT DIRECT VENT GS SYSTEM and
Regency® DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal
one 90o elbow).
Note: Must use optional rigid pipe adapter (Part # 770-994) when using Simpson Dura-Vent pipe (Refer to "Simpson Dura-Vent Venting"
section).
Simpson Dura-Vent
5" inner diameter
8" outer diameter
Regency® Flex Vent
5" inner diameter
8" outer diameter
A vent guard should be used
whenever the termination is lower
than the specified minimum or as
per local codes.
Note: Regency® Direct Vent System
(Flex) is only approved for
horizontal terminations.
•
•
•
Maintain clearances to combustibles as listed in "Clearances" section
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
17
INSTALLATION
Horizontal Venting with Three (3) 90o Elbows
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Option
A)
V
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
Option
A)
H
V
H+H1+H2
3' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 8 feet
total horizontal.
Please note minimum 1
foot between 90o elbows is
required.
Withtheseoptions,max.
totalpipelengthis30feet
with min. of 11 feet total
vertical and max. 9 feet
total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
1' Max. 1' Min.
2' Max. 3' Min.
3' Max. 5' Min.
4' Max. 7' Min.
5' Max. 9' Min.
B)
B)
C)
C)
D)
D)
E)
E)
F)
F)
6' Max. 11' Min. 9' Max.
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
H
V
H + H1
3' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options,
max. total pipe length is
30feetwithmin.of8feet
total vertical and max. 8
feet total horizontal.
Pleasenotemin.1foot
between90o elbowsis
required.
1' Max. 1' Min.
2' Max. 2' Min.
3' Max. 4' Min.
4' Max. 6' Min.
5' Max. 8' Min.
B)
C)
D)
E)
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
With these options,
max.totalpipelength
is30feetwithmin.of
12 feet total vertical
and max. 9 feet total
horizontal.
Please note min.
1 foot between
90o elbows is
required.
Option
A)
V
H
V + V1 H + H1
2' Min. 1' Max. 3' Min. 4' Max.
3' Min. 2' Max. 4' Min. 5' Max.
4' Min. 3' Max. 6' Min. 6' Max.
5' Min. 4' Max. 8' Min. 7' Max.
6' Min. 5' Max. 10' Min. 8' Max.
7' Min. 6' Max. 12' Min. 9' Max.
B)
C)
D)
E)
F)
Vertical Venting with Two (2) 90o Elbows
Vertical Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
With these options,
max. total pipe length is
30feetwithmin.of6feet
total vertical and max. 8
feet total horizontal.
Pleasenotemin.1foot
between90o elbowsis
required.
With these options, max. total
Option
A)
V
H
V + V1
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
Option H + H1
V
pipe length is 30 feet with min.
of6feettotalverticalandmax.
6 feet total horizontal.
1' Min. 4' Max.
2' Min. 5' Max.
3' Min. 6' Max.
4' Min. 7' Max.
5' Min. 8' Max.
A)
B)
C)
D)
E)
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
B)
Please note min. 1 foot
between 90o elbows is
required.
C)
D)
E)
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
19
INSTALLATION
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
With these options,
max. total pipe length
is 30 feet with min. of
11 feet total vertical
and max. 7 feet total
horizontal.
Pleasenotemin.1foot
between90o elbowsis
required.
Option
A)
H
V
H + H1
V + V1
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
1' Max. 1' Min. 3' Max.
2' Max. 2' Min. 4' Max.
3' Max. 3' Min. 5' Max.
4' Max. 4' Min. 6' Max.
5' Max. 5' Min. 7' Max.
B)
C)
D)
E)
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
With these options, max.
total pipe length is 30 feet
with min. of 10 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
Option
A)
V
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1
4' Min.
6' Min.
7' Min.
8' Min.
9' Min.
10' Min.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
B)
C)
D)
E)
F)
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
20
INSTALLATION
VENTING ARRANGEMENTS
VERTICAL TERMINATIONS
SIMPSON DURA-VENT DIRECT VENT GS SYSTEM
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90o elbow and
one 45o elbow, with Simpson Dura-Vent Direct Vent GS vent systems for Propane and Natural Gas.
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
Note: Must use optional rigid pipe adapter when using Simpson Dura-Vent pipe (Part # 510-994).
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
The P48-2 is approved for a maximum 40 ft. straight vertical, with
Simpson Dura-Vent Direct Vent GS vent systems for Propane and
Natural Gas, as per diagram.
The shaded area in the diagram shows all allowable combinations
of straight vertical and offset to vertical terminations with Simpson
Dura-Vent Direct Vent GS vent systems for Propane and Natural Gas.
Maximum two 45o elbows allowed.
•
•
Vent must be supported at offsets
Firestopsarerequiredateachfloorlevelandwheneverpassing
through a wall.
•
Maintainclearancestocombustiblesaslistedinthe "Clearances"
section.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
22
INSTALLATION
Note: For best results and optimum
performance with each approved
venting system, it is highly
recommended to apply “Mill-Pac”
sealant (supplied) to every inner
pipe connection. Failure to do so
mayresultindraftingorperformance
issues not covered under warranty.
Silicone (red RTV) is optional.
UNIT INSTALLATION
WITH HORIZONTAL
TERMINATION
Install the vent system according to the
manufacturer's instructions included with the
components.
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
b) Horizontal runs of vent must be
supported every 3 feet (0.9meter). Wall
straps are available for this purpose.
5) Mark the wall for a 11" x 11" (279mm x
279mm) square hole. The center of the
square hole should line up with the center-
lineofthehorizontalpipe.Cutandframethe
11inch (279mm)squareholeintheexterior
wall where the vent will be terminated.
Diagram 5
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
2) DirectVentpipeandfittingsaredesignedwith
specialtwist-lockconnectionstoconnectthe
ventingsystemtotheapplianceflueoutlet.A
twist-lock appliance adaptor is an available
option that must be used in conjunction with
the Simpson Dura-Vent Direct Vent GS
system. Install the adaptor after the unit is
set in its desired location otherwise the unit
will not fit through the
If the wall being penetrated is constructed
of non-combustible material, i.e. masonry
block or concrete, a 8" (203mm) diameter
hole is acceptable.
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble (Part # 1247) over the vent pipe.
8) Slide the appliance and vent assembly
towards the wall carefully inserting the
vent pipe into the vent cap assembly. It is
important that the vent pipe extends into the
vent cap sufficient distance so as to result
in a minimum pipe overlap of 1-1/4 inches
(32mm).Securetheconnectionbetweenthe
vent pipe and the vent cap by attaching the
two sheet metal strips extending from the
vent cap assembly into the outer wall of the
vent pipe. Use the two sheet metal screws
provided to connect the strips to the pipe
section. See Diagram 6.
36-5/8" (930mm) high frame opening.
3) Put a bead of silicone inside the outer
section of the adapter and a bead of Stove
Mate on the inner collar. Slip the adapter
over the existing inner and outer flue collar
and fasten to the outer collar only with the
3 supplied screws (drilling pilot holes will
make this easier). Level the fireplace and
fasten it to the framing using nails or screws
through the nailing strips.
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
Diagram 2
Note:
Note:
a) Thehorizontalrunofventmustbelevel,
or have a 1/4 inch rise for every 1 foot
of run towards the termination. Never
allow the vent to run downward. This
couldcausehightemperaturesandmay
present the possibility of a fire.
a) Twist-lockprocedure:Fourindentations,
locatedon thefemaleendsofpipesand
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide in
to the four entry slots on the male ends.
(Diagram 1) Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
arefullylocked.Thefemalelockinglugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
b) The location of the horizontal vent
terminationonanexteriorwallmustmeet
alllocalandnationalbuildingcodes,and
must not be blocked or obstructed. For
External Vent Terminal Locations, see
diagram in "Exterior Vent Termination
Locations" section.
Diagram 6
9) Install wall thimble in the center of the 11"
(279mm) square and attach with wood
screws (Diagram 7).
6) The arrow on the vent cap should be
pointing up. Insure that the 1-1/4"(32mm)
clearances to combustible materials
are maintained (Diagram 5). Install the
termination cap.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff
or furring strips must be used to
ensure that the termination is not
recessed into the siding.
Diagram 1
Diagram 7
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
23
INSTALLATION
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
UNIT INSTALLATION
WITH VERTICAL
TERMINATION
NOTE:
Diagram 5
For best results and optimum performance
with each approved venting system, it is
highly recommended to apply “Mill-Pac”
sealant(supplied)toeveryinnerpipeconnec-
tion. Failure to do so may result in drafting
or performance issues not covered under
warranty. Silicone (red RTV) is optional.
1) Maintain the 1-1/4"
(32mm) clearances
(air spaces) to
combustibles when
passing through ceilings,
walls, roofs, enclosures,
attic rafter, or other
Minimum Vent
Height
Roof Pitch
Feet
2
Meters
0.61
0.61
0.61
0.76
0.99
1.22
1.52
1.83
2.13
2.29
2.44
nearby combustible
surfaces. Do not pack air
spaces with insulation.
Check "Venting
Arrangemnt - Vertical
Termination" section for
the maximum vertical
rise of the venting
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
2
2
2.5
3.25
4
system and the
maximum horizontal
offset limitations.
5
6
2) Set the gas appliance
7
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/4"(32mm). Slip the
flashing under the shingles (shingles should
overlap half the flashing) as per Diagram 4.
in its desired location.
Diagram 1
7.5
8
Drop a plumb bob down from the ceiling
to the position of the appliance flue exit,
and mark the location where the vent will
penetratetheceiling. Drillasmallholeathis
point. Next, drop a plumb bob from the roof
to the hole previously drilled in the ceiling,
and mark the spot where the vent
A poor draft, or down drafting can result from
highwindconditionsnearbigtreesoradjoining
roof lines, in these cases, increasing the vent
height may solve the problem.
will penetrate the
Determineifceiling
joists, roof rafters
orotherframingwill
obstructtheventing
system. You may
wish to relocate
the appliance
or to offset, as
shown in Diagram
2 to avoid cutting
load bearing
members.
r o o f .
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
8) Install the vertical termination cap by twist-
locking it.
Note: Anyclosetsorstoragespaces,which
the vent passes through must be
enclosed.
Diagram 4: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed.
This allows for small adjustments.
Diagram 2
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut
a 11 inch (279mm) square hole. Frame the
hole as shown in Diagram 3 and install the
firestop.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic
to avoid obstructions, it is important
to support the vent pipe every 3
feet (0.9 meter), to avoid excessive
stress on the elbows, and possible
separation. Wall straps are available
for this purpose
(Diagram 2).
Galvanizedpipeisdesirableabovetheroofline
duetoitshighercorrosionresistance.Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
heightrequirementsspecifiedinDiagram5or
local codes. Note that for steep roof pitches,
the vertical height must be increased.
Diagram 3
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
24
INSTALLATION
4) Separatethe2halvesofthewallthimbleand
securely fasten the one with the tabs to the
outside wall making sure that the tabs are
on top and bottom. Fasten the other thimble
half to the inside wall. The thimble halves
slip inside each other and can be adjusted
for 2 x 4 or 2 x 6 walls. The liners must slip
over the collars a minimum of 1-3/8".
IMPORTANT: Do not locate termination
hood where excessive snow or ice
buildup may occur. Be sure to check vent
terminationareaaftersnowfalls, andclear
to prevent accidental blockage of venting
system. When using snow blowers, make
sure snow is not directed towards vent
termination area.
UNIT
INSTALLATION
with Regency® Direct Vent
System (Flex)
1) Locate the unit in the framing, rough in the
gas (preferably on the right side of the unit)
and the electrical (Junction block is on the
left side) on the left. Locate the centerline of
the termination and mark wall accordingly.
Cut a 11"(279mm) hole in the wall (inside
dimension).
5) Slip the assembled liner and termination
assembly through the thimble making sure
the termination cap faces up (there are
markings on the cap that show which way
is up). This will position the termination cap
with proper down slope for draining water.
Fasten the cap to the outer wall with the 4
supplied screws.
ASTROCAP XL
DIMENSIONS
Note: A top clearance of 2-1/2"(64mm)
and side & bottom clearance of
1-1/2"(38mm) must be maintained
exceptthatonlya1"(25mm)clearance
is needed at the termination end. We
recommend framing a 11"(279mm) x
11"(279mm)(insidedimensions)hole
togivestructuralrigidityformounting
the termination.
6) Pull the centre 5"(127mm) liner and outer
8"(203mm) liner out enough to slip over
the flue collars of the fireplace. (You may
wish to cut the liner shorter to make it more
workable.) Do not bend liner more than
90o.
7) Apply Mill Pac over the fireplace inner collar
and slip the 5"(127mm) liner down over it
and attach with 3 supplied screws.
Note: To make
the installation
more aesthetically
8) Do the same with the 8"(203mm) liner.
9) Applyabeadofsiliconebetweenthethimble
and termination and around the outer edge
of the terminal at the wall in order to keep
the water out.
p l e a s i n g ,
w e
recommendframing
outasquaretomount
the terminal to.
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination
is not recessed into the siding.
2) Level the fireplace and fasten it to the fram-
ing using nails or screws through the nailing
strips.
3) Assemble the vent assembly by applying
Mill Pac to the 5"(127mm) inner collar of
theterminationand slippingthe5"(127mm)
liner over it at least 1-3/8" (35mm). Fasten
with the 3 screws (drilling pilot holes will
make this easier). Apply Mill Pac or high
temperature silicone to the 8"(203mm) flex
pipe and slip it over the 8" outer collar of
the vent terminal at least 1-3/8"(35mm) and
fasten with the 3 screws.
NOTE: Horizontal sections must be sup-
ported at intervals not exceeding 3
feet (0.9 meter). (Flame picture and
performance will be affected by sags
in the liner).
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
25
INSTALLATION
For USA installations follow local codes and/or Themanifoldpressureiscontrolledbyaregulator
the current National Fuel Gas Code, ANSI builtintothegascontrol, andshouldbechecked
P48-NG2 SYSTEM DATA
Z223.1.
at the pressure test point.
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#27
When using copper or flex connectors use only Note: To properly check gas pressure, both
approved fittings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and flex
connectors are usually considered to meet this
requirement.
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
Max. Input Rating 51,000 Btu/h
Min. Input Rating 29,000 Btu/h
Supply Pressure
min.5.0" w.c.
1) Make sure the valve is in the "OFF"
position.
Manifold Pressure
(High)
Important:Alwayscheckforgasleakswitha
3.8"+/- 0.2"w.c.
soapandwatersolutionorgasleakdetector. 2) Loosen the "IN" and/or "OUT" pressure
Do not use open flame for leak testing.
tap(s), turning counterclockwise with a
1/8" wide flat screwdriver.
Log Set: Ceramic fibre, 8 per set.
Vent System: Simpson Dura-Vent Direct
Vent System, Regency® Flex Kit
3) Attach manometer to "IN" and/or "OUT"
PILOT ADJUSTMENT
pressure tap(s) using a 5/16" ID hose.
P48-LP2 SYSTEM DATA
4) Light the pilot and turn the valve to "ON"
position.
Conversion Kit# 372-969
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#47
Max. Input Rating 48,000 Btu/h
Min. Input Rating 26,000 Btu/h
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8" flat
screwdriver. Note: Screw should be snug,
but do not over tighten.
Supply Pressure
min.12.0" w.c.
Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile, 1 around
the thermocouple and 1 flowing across the
burner (it does not have to be touching the
burner).
Manifold Pressure
(High)
11"+/- 0.2" w.c.
Log Set: Ceramic fibre, 8 per set.
Vent System: Simpson Dura-Vent Direct
Vent System, Regency® Flex Kit
S.I.T. VALVE DESCRIPTION
1) Gas on/off knob
2) Manual high/low adjustment
3) Pilot Adjustment
4) Thermocouple Connection - option
5) Outlet Pressure Tap
6) Inlet Pressure Tap
7) Pilot Outlet
8) Main Gas Outlet
9) Alternative TC Connection
Point
Note: Ifyouhaveanincorrectflamepattern,
contact your Regency® dealer for
further instructions.
Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or
thermopile or thermocouple.
HIGH ELEVATION
This unit is approved in Canada for altitude 0
to 4500 ft. (CAN1 2.17-M91).
GAS LINE
INSTALLATION
The gas line can be brought through either
the right, the left side or the bottom of the
appliance. The gas valve is situated on the
bottom of the unit.
The gas line connection may be made of rigid
pipe,copperpipeoranapprovedflexconnector.
(If you are using rigid pipe, ensure that the valve
can be removed for servicing.) Since some
municipalities have additional local codes it is
alwaysbesttoconsultwithyourlocalauthorities
and the CAN/CGA B149 installation code.
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
26
INSTALLATION
CONVERSION KIT FROM NG TO LPG PART #372-969
for P48-2 SIT 820 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
7) Remove burner orifice with a 1/2"
4) Remove the burner assembly by remov-
ing the 1 Phillips head screw and then
slide the burner assembly away from the
orifice and lift out.
Each Kit contains one LPG
Conversion Kit and one DC
Sparker Kit.
wrench and discard. Use another
wrench to hold on to the elbow behind
the orifice.
LPG Conversion Kit Contains:
Qty. Part #
Description
1
1
904-434
918-590
Burner Orifice #47
Decal "Converted to
Propane"
1
1
1
908-529
910-037
918-478
5/32" Allen Key
LP Injector (Pilot Orifice)
Instruction Sheet
DC Sparker Kit Contains:
Qty. Part # Description
Burner Orifice
Diagram 1:
Remove the left screw and then slide the
burner assembly away from the orifice and
lift out.
1
1
1
1
2
820-475
820-476
904-153
904-330
904-531
Bracket DC Sparker
Bracket DC Sparker
Washer #8 External Star
Nut 8-32 Hex
8) Reinstall new burner orifice LP stamped
#47 and tighten.
Bushing Split Plastic
0.500 in.
9) Turn control knob to the “OFF” position.
1
2
1
1
1
904-543
904-553
910-073
910-074
910-078
Screw 8-32 x 3/4 Pan
Head
10) Remove the black protection cap by
Screw #8 x 1/2 Type "B",
Black Oxide
hand from the high-low knob (Fig.1).
Spark Generator
Battery Holder
Spark Generator
Switch C/W Wire
Battery Size AA
Energizer En91
Clip Wire Holder
Wire Fan To Power Cord
Ground 30 in.
1
1
910-199
910-903
5) Pull off the pilot
cap to expose
the pilot orifice.
1
918-478
904-781
904-782
Instruction Sheet
Velcro Hook, Black
Velcro Hook, Black
Fig.1
Installation of LPG
Conversion Kit:
6) Unscrew the pilot orifice with the allen
key and replace with the LP pilot orifice
in the kit and replace pilot cap.
1) Remove the louvers and trim kit. Re-
move the front door.
2) Remove the logs, embers.
3) Remove the grate by lifting straight up.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
27
INSTALLATION
11) Insert a 5/32” or 4mm Allen wrench into
the hexagonal key-way of the screw
(Fig. 2), rotate it counter-clockwise until
it is free and extract it.
15) Verify that if the conversion is from NG to
LPG, the screw must be re-assembled
with the red o-ring visible (Fig. 5).
Installation of the DC Sparker:
24) Locate the Piezo Ignitor situated at the
side of the valve.
LPG Configuration
Red o-ring visible
Piezo
Ignitor
Fig.5
25) RemovethePiezoIgnitorbyunscrewingthe
nut at the back of the mounting bracket.
16) Re-assemble the black protection cap
(Fig. 6).
Fig.2
Ignitor
Wire
12) Check that the screw is clean and if
necessary remove dirt.
13) Flip the screw (Fig. 3).
Piezo
Ignitor
26) Disconnect the ignitor wire from the Piezo
Ignitor and connect it to the DC Sparker.
Fig.6
DC
Sparker
Fig.3
WARNING!
Ignitor
Wire
14) Using the Allen wrench as shown in
Fig.4, rotate the screw clockwise until
snug, do not overtighten.
Also check that the pilot
and main burner injectors are
appropriate for the gas type.
27) Connect the DC spark generator wires
to the SIT Valve with the screw, which is
provided in the kit.
17) Reverse steps 4) to 1).
18) Attach the label "This unit has been
converted to LPG" near or on top of the
serial # decal.
19) Replace yellow "Natural Gas" label with
red "Propane" label
20) Check for gas leaks.
Fig.4
21) Check inlet and outlet pressures.
22) Check operation of flame control.
WARNING!
Do not overtighten the screw.
Recommended to
grip the wrench by the short side.
23) Check for proper flame appearance and
glow on logs.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
28
INSTALLATION
32) Plug the DC spark generator wires to the 35) Mount the heat shield to the DC Sparker.
28) Locatethegroundlugattherecepticalbox,
DC Sparker.
Secure into place with the velcro, which is
provided in the kit.
left of the unit.
36) Find a location which is not too hot and
is easy to reach for changing the battery.
Note: It should be kept away from the
chain.
29) Connect one end of the supplied green
ground wire to the lug with the nut and
washer from the kit.
33) ConnectthegroundwiretotheDCSparker
mounting bracket.
Chain
Ground
wire from
kit
30) Install the 1/2" bushing to the heat
shield.
37) Tie up the loose wire with the wire clip.
34) Install the supplied battery into the DC
Sparker Box by opening the battery
compartment.
NOTE:The battery in the DC Sparker Box
will need to be replaced annually.
Battery
Compartment
31) Run the other end of the ground wire and
DC spark generator wires through the
bushing on the heat shield.
Heat Shield
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
29
INSTALLATION
BRICK PANELS INSTALLATION
5) Place the top bracket onto the front edge of the top panel (refer to
1) Unhook the 2 spring loaded hooks from the bottom of the flush door
Diagram 5).
and lift the Flush Front off the unit.
2) Unwrap the brick pattern panels from the protective wrapping.
Top Bracket
Note: The logs must not be in the unit.
a) Loosen the two screws from the bottom of the baffle plate. Install
the bottom clips onto the baffle plate (refer to Diagram 1).
Diagram 5
6) Slide the top panel and bracket assembly carefully onto the baffle
plate ensuring the panel is centered. Make sure the tabs of the top
bracket fit into the baffle openings (refer to Diagrams 6 & 7). The
back of the top brick panel sits on top of the bottom clips.
Bottom Clips
Tabs
Diagram 1
Diagram 6
3) Insert the back brick panel first by carefully slipping it between the
back wall of the firebox and the rear log bracket (refer to Diagram 2).
Diagram 2
Diagram 7
4) Put the side panels in next. Tilt them in towards the middle of the
firebox and put the bottom front corner in first. Be very careful not
to scratch them on the firebox hardware. Place them flat up against
the wall, they should fit snugly against the top of the firebox (refer to
Diagrams 3 & 4).
NOTE: If the bottom brick panel must be removed: Remove the
grate, then remove the Burner Tray. See "Removing
Valve" section.
IMPORTANT
Dangerousoperatingconditionsmay
occur if the panels are broken.
Diagrams 3 & 4
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
LOG SET INSTALLATION
Read the instructions below carefully and refer to the dia-
grams. If logs are broken do not use the unit until they are
replaced. Broken logs can interfere with the pilot opera-
tion.
The gas log kit (Part # 370-930) contains the following pieces:
02-88
a) 02-83
b) 02-84
c) 02-85
d) 02-86
e) 02-87
f) 02-88
g) 02-89
h) 02-90
Center Cross Log
Right Side Cross Log
Front Left Side Log
Front Right Side Log
Left Side End Log
Rear Log
Middle Right Side Log
Right Side End Log
i) 902-154 Embers (Lava)
j) 902-179 Vermiculite
k) 946-669 Platinum Embers (supplied with packaged manual)
4) Place Log 02-85 on the front left side of the burner.
Position the right end of the log into the pin on the
burner and rest the left end of the log between the 1st
grate post and the front tab.
If you will be installing the optional brick panels, install them
prior to installing the logs.
02-90
02-88
02-88
02-85
02-87
02-89
02-86
Pin
Tab
1st Grate Post
02-84
02-85
02-83
5) Line up the two holes on the underside of Log 02-86
with the 2 pins on the right side of the burner and posi-
tion into place.
The "02" reference numbers (i.e. 02-83)
are molded into the rear of each log.
1) Carefully remove the logs from the box and unwrap
them. The logs are fragile, handle with care - do not
force into position.
02-88
2) Sprinkle the vermiculite all over the top of the base
brick panel.
02-86
3) Line up the two holes on the underside of Log 02-88
with the 2 pins at the rear of the grate and position
into place.
02-85
Pins
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
31
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
8) Line up the hole on the underside of Log 02-84 with
the pin on Log 02-86 and position the notch on the
bottom of the log into the last grate post.
6) Embers should be placed in front of Log 02-85 and
Log 02-86.
Separate platinum embers and place around the em-
bers at the front of the burner.Avoid stacking platinum
embers.
02-88
02-84
02-86
02-83
02-86
02-85
Last Grate Post
Pin in Log
Embers
9) Place Log 02-89 against the notch in Log 02-84. Rest
CAUTION: DO NOT cover burner ports with embers.
the notch at the end of the log against the grate.
7) Place Log 02-83 onto the pin in Log 02-88 and position
the notch on the bottom of the log into the 4th grate
post.
02-88
02-88
02-89
02-84
02-83
02-86
02-85
Notch
Rest notch at the end of
the log against the grate.
Rest log onto the pin
in Log 02-88.
02-83
02-86
02-85
4th Grate Post
Position the notch on the bottom of
the log into the 4th grate post.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
32
INSTALLATION
11) Place Log 02-87 on the middle left side of the burner.
Position the bottom rear of the log against the rear
tab on the left side of the grate. Rest the front edge
of the log in the notches on Log 02-85.
10) Place Log 02-90 onto the right side of the grate. Posi-
tion the cut-out on the underside of the log onto the
grate bar.
02-87
02-90
Tab
Cut-out
on the underside
of the log.
02-85
02-90
02-83
02-88
02-89
02-87
02-84
02-85
Position the cut-out onto
the grate bar.
Notches
02-87
02-88
02-90
02-89
02-85
02-83
02-84
02-86
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
33
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
STANDARD
FLUSH LOUVERS
1) Install the top louver by sliding the two
bracket clips into the brackets located
underneath the top of the firebox.
FLUSH DOOR
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, diagram 1.
2) Installthebottomlouverbyfoldingthelouver
down and then sliding the Bottom Louver
bracket down onto the 2 pins on the base
of the unit (diagram 1). Secure with 1 screw
as per diagram 2.
Burner ON/OFF control box attached to
bottom flush louver.
OPTIONAL FLUSH TRIM
Attach the round magnets to the back of the
top trim piece and to the bottom trim piece,
then attach trim to the top and bottom of Flush
door.
Diagram 1
Diagram 2
Diagram 1
Be careful that the glass gasket does not roll up;
theremustbeagapbetweenthegasketandthe
door lip to ensure that the door sits securely on
the unit. Diagram 2.
Note: Top and
bottom louvers
are different.
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace. Using the 2 screws on the
louver, secure the control box in place.
Diagram 2
Use the hook to pull the spring out until you
can put the hook into the slot on the bottom
door bracket. Repeat for 2nd and 3rd spring.
See diagram 3.
Diagram 3
NOTE: Springs must always be OVER
not under the gas line.
Burner ON/OFF
control box
Screws on
louver bracket
To remove the flush door, reverse the above
steps.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
34
INSTALLATION
4) Reconnect the 2 spring hooks securing the
flush door.
OPTIONAL BAY DOOR
BAY LOUVERS
The Bay louvers MUST be used
1) Install top louver by sliding the two bracket
clips into the brackets located on top of the
baydoor.Seebelow.Thefittedlouverleaves
a small gap between faceplate bottom and
louver top.
5) Slide the valve extension knobs onto the
valve knobs.
with the Bay glass option.
The optional Bay door is an overlay on the
flush front. The standard flush door and glass
must remain on the unit.
1) Unhook the 2 spring loaded hooks from the
bottom of the flush door.
Note: If any maintenance etc. must be
done in the firebox, first remove the
Bay louvers and door.
2) Hook the top of the bay door over the flush
door flange and swing the bottom against
the bottom flange of the flush door.
OPTIONAL BAY TRIM
Attach the supplied magnets each to the back
of the top and bottom trim pieces, and attach
trim to the top and bottom of Bay door. See
diagrams 3 and 4.
Note: Top and bottom louvers and
brackets are different.
2) Install bottom louver by sliding the two
bracket clips into the brackets located
underneath the bay door. Install bottom
louverbyslidingthetwobracketclipsintothe
brackets located underneath the bay door
and secure with 1 screw on each end.
Diagram 3
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace. Using the 2 screws on the
louver, secure the control box in place.
3) Securetotheflushdoorbottombracketwith
2 screws provided.
Burner
ON/OFF
control box
Screws
on louver
bracket
Diagram 4
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
35
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
DOUBLE SCREEN
DOOR
OPTIONAL FINISHING TRIM
NOTE: Remove both the Flush Louvers or Bay Louvers and the Flush Front or Bay Front prior
to installing the Finishing Trim.
1) Pull out the top louver.
1) Install the Finishing Trim sides as shown in the diagram, line up the holes in the side trim with
2) Center the screen door and hook over the
the holes in the firebox side.
flush door.
2) Secure with 2 screws per side.
3) Loosen the 3 screws in the top inside edge of the firebox.
4) Slide the Finishing Trim Top over the Side Trim pieces and fit the bottom bracket slots over
the screws. Tighten the 3 screws to secure.
3) Open the screen door(s) and secure the
screen door to the flush door front with 2
clips on the bottom left and right side.
Clip locations
Clip installed on right side.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
36
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
OPTIONAL
REMOTE CONTROL
OPTIONAL
WALL SWITCH
OPTIONAL
WALL THERMOSTAT
Can be used with Option 2 or 3
but not both.
UsetheRegency® RemoteControlKit approved 1) Run the supplied 15' of wire through the
for this unit. Use of other systems may void
your warranty.
Can be used with Option 1 or 3
but not both.
Can be used with Option 1 or 2
but not both.
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram in
"Wiring Diagram" section. Use the table below
to determine the maximum wire length.
back gas inlet opening. Be careful not to
damage wire.
The remote control kit comes with a hand held Note: We recommend a maximum of 15'
transmitter, a receiver and a wall mounting
plate.
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
Note:Preferableifthethermostatisinstalled
on an interior wall.
1) Choose a convenient location on the wall
Regency® offers an optional programmable
thermostat but any 250-750 millivolt rated non-
anticipator type thermostat that is CSA, ULC or
UL approved may be used.
to install the receiver and the receptacle 2) Connect the wire to the supplied wall switch
box (protection from extreme heat is very
important). Run wires from the fireplace
to that location. Use the Thermostat Wire
Table.
and install into the receptacle box.
CAUTION
Do not connect millivolt
wall switch wire to a 120V wire.
CAUTION
2) Connect the two wires to the gas valve. See
Do not connect millivolt
wall thermostat wires
to a 120V wire.
diagram.
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
CAUTION
Do not connect millivolt
remote control wires to a
120V wire.
3) Install3AAAalkalinebatteriesintransmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
37
INSTALLATION
WIRING DIAGRAMS
(Do not cut the ground terminal off under
any circumstances.)
NOTE: Even if the fan is not purchased with
the unit, it is still a good idea to hardwire the
terminal block in case the fan is installed at a
later date.
No electrical power supply is required for the
gas control to operate. 120 Volt AC power is
needed for the fan switch and blower. The fan
can be hard wired if desired. A terminal block is
provided on the left hand side of the unit.Athree
wire power cord can also be used and plugged
into a suitable receptacle.
** However DO NOT leave this connection
live until the fan is installed.**
For NATURAL GAS Units and Units NOT Equipped with DC Spark Boxes
Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.
CAUTION: Label all wires
prior to disconnection
when servicing controls.
Wiring errors can cause
improper and dangerous
operation.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
38
INSTALLATION
For PROPANE Units and Units Equipped with DC Spark Boxes*
*For installation of the DC Spark Box refer to the LP Conversion instructions in this manual.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
39
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLING THE OPTIONAL FAN
120 Volt AC power is needed for the fan switch
andblower.Thefancanbehardwiredifdesired.
The receptacleboxshouldbeinstalled on theleft
handsideoftheunitbyaqualifiedelectrician.The
neutral (wider) slot of the polarized receptacle
should be at the top.
6) Slide the thermodisc/cover assembly into 9) Attach the two control boxes to the bottom
the bracket clip on the underside of the
firebox. Check that no wire will touch the
hot surfaces. Diagram 2.
louver and tighten the 2 screws on the left
side and 2 screws on the right side.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
1) Shut the power off.
2) Remove the standard flush door and the
optional bay door, if installed. Open the
bottom louver door.
Secure left side with 2 screws.
3) Remove the 2 screws holding the Burner
ON/OFF switch and bracket to the bottom
louver and lift the assembly out.
Diagram 2
7) Attach the Fan control box to the Burner
ON/OFF control box. Diagram 3.
Secure right side with 2 screws.
10) Secure the fan wires and power cord by
attaching one of the adhesive backed wire
holder clips (Part #910-199) onto the stove
base. Use the second clip to bundle up the
wiresapproximately4"fromthecontrolbox.
Ensurethatthereisnointerferencewiththe
wires when the louver is closed and that
no wire will touch the hot metal surfaces
or sharp edges.
Diagram 3: Use the clip & hook on the side of
the control boxes to join them together.
8) Secure the two boxes together with one
4) Turn the fan base on its side (with the base
facing towards you) and then slide the fan
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs.Takecarenottodamagetheinsulation
onthefanbase.Ensurethatthefanblades
do not rub against the valve tubing.
Diagram 1.
screw.
11) Plug the fan power cord into the rear end of
the receptacle box to provide the maximum
clearance from the louvers.
TO REMOVE THE FAN
1) Shut the power off.
2) Reverse the above instructions.
Secure the 2 boxes together
with one screw.
NOTE:
The bearings are lubricated for life. Do not
lubricate them. Make sure you vacuum the
fan area on a regular basis.
IMPORTANT:
These fans collect a lot of dust from within
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a soft
brush nozzle.
Diagram 1
5) Connect fan ground cable to ground lug.
Refer to wiring diagram.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
40
OPERATING INSTRUCTIONS
2) Turn gas control knob so indicator points
During the first few fires, a white film
may develop on the glass front as part of
the curing process. The glass should be
cleaned after the unit has cooled down
or the film will bake on and become very
difficult to remove. Use a non-abrasive
cleanerandDONOTATTEMPTTOCLEAN
THE GLASS WHILE IT IS HOT.
OPERATING
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the igniter button several times until the
pilot lights.After approximately one minute,
releasethegascontrolknob.Thepilotflame
should continue to burn. If the pilot does not
remainlit,repeatoperationallowingalonger
period before releasing gas control knob.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
AERATION
ADJUSTMENT
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON"
position.
5) Verify that the venting and cap are
The air shutter can be adjusted by moving the
adjusting wire up or down.The wire is accessed
through the bottom louver opening. Open the
air shutter for a blue flame or close for a more
yellow flame. The burner aeration is factory set
but may need adjusting due to either the local
gas supply or altitude.
unobstructed.
6) Ensure that the brick panels are installed.
5) Use the wall switch, thermostat or remote
control to turn on the unit.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
6) Rotate the flame height regulator to adjust
the flame height higher or lower.
Minimum Air Shutter Opening:
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
3/16"
Fully Open
Natural Gas
Propane
SHUTDOWN
PROCEDURE
CAUTION:Carbonwillbeproducedifairshutter
is closed too much.
1) Use the wall switch, thermostat or remote
Note: Any damage due to carboning
resulting from improperly setting
the aeration controls is NOT covered
under warranty.
control to turn off the main burner.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
service is to be performed.
LIGHTING
PROCEDURE
FIRST FIRE
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
IMPORTANT
To ignite or reignite the pilot,
you must first release the
tension springs below the door.
Adjustment Wire - Pull down to open or
push up to close aeration cap.
The first fire in your stove is part of the paint
curing process. To ensure that the paint is
properlycured,itisrecommendedthatyouburn
your fireplace for at least four (4) hours the first
time before you use it with the fan on.
Only when the pilot holds, without pressure
being applied to the control knob, reapply the
tension springs to the door. The unit must
not be operated with the tension springs
unattached.
Closed - Tall yellow
Open - Short Blue
Whenfirstoperated,theunitwillreleaseanodour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at
this time. Open a few windows to ventilate the
room for a couple of hours.
Note: Aeration Adjustment should only be
performedbyanauthorizedRegency®
Installer at the time of installation or
service.
NOTE: For all propane units and units
equipped with electric spark boxes,
see "Copy of Lighting Plate Instruc-
tions" section for more details.
Note: When the glass is cold and the
appliance is lit, it may cause
condensation and fog the glass.
This condensation is normal and
will disappear in a few minutes as
the glass heats up.
IMPORTANT Gas on/off knob cannot be
turned from "PILOT" to "OFF" unless it is
partially depressed.
1) Turn burner OFF using "ON/OFF" switch.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
41
OPERATING INSTRUCTIONS
Copy of the Lighting Plate Instructions
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
fromyourgasappliance.Thisisperfectlynormal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listedbelowaresomeexamples.Allarenormal
operatingsoundsandshouldnotbeconsidered
as defects in your appliance.
Blower:
Regency® gasappliancesusehightechblowers
to push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube and logs and is made of a different
gauge material from the rest of the firebox and
body.Therefore,thevaryingthicknessesofsteel
will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit these
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
Blower Thermodisc:
When this thermally activated switch turns ON
it will create a small "clicking" sound. This is the
switch contacts closing and is normal.
OFF
Gas Inlet
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dullclickingsoundmaybeaudible,thisisnormal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
Gas Inlet
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
42
MAINTENANCE
MAINTENANCE
INSTRUCTIONS
GENERAL VENT
MAINTENANCE
THERMOPILE /
THERMOCOUPLE
Conduct an inspection of the venting system
semiannually. Recommended areas to inspect
as follows:
1) OpentheBottomLouversorGrills. Remove
1) Alwaysturnoffthegasvalvebeforecleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
the Top Louver or Grill.
2) Open and remove door.
3) Remove log set and embers.
4) Remove grate and burner.
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or
streaks, and in extreme cases, holes.
These components should be replaced
immediately.
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
5) Disconnect thermocouple by loosening
nut from the valve with a 9mm wrench.
Disconnect thermopile by loosening 2
screws marked TP on the valve.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
6) Remove 2 screws from the pilot assembly
and pull up far enough to be able to loosen
the thermocouple or thermopile with a 7/16"
wrench. NOTE: the pilot line is very fragile,
use caution when pulling it up.
7) Drop the thermocouple or thermopile down
through the extrusion and pull it out of the
unit.
3) Check for evidences of excessive
condensation,suchaswaterdropletsforming
in the inner liner, and subsequently dripping
outthejoints,Continuouscondensationcan
cause corrosion of caps, pipe, and fittings.
It may be caused by having excessive
lateral runs, too many elbows, and exterior
portions of the system being exposed to
cold weather.
3) The heater is finished in a heat resistant
paintandshouldonlyberefinishedwithheat
resistant paint. Regency® uses StoveBright
Paint - Metallic Black #6309.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flameoftheburnerperiodically,makingsure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
8) Reinstall the new ones in reverse order.
4) Inspect joints, to verify that no pipe
sections or fittings have been disturbed,
and consequently loosened. Also check
mechanical supports such as Wall Straps,
or plumbers' tape for rigidity.
5) The appliance and venting system must be
inspected before use, and at least annually,
byaqualifiedfieldserviceperson, toensure
that the flow of combustion and ventilation
air is not obstructed.
GLASS GASKET
If the glass gasket requires replacement use a
tadpole glass gasket (Part # 936-155).
LOG REPLACEMENT
Note: Never operate the appliance without
the glass properly secured in place.
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
GOLD-PLATED
LOUVERS & TRIM
The 24 carat gold-plated finish on the louvers
and trim requires little maintenance, and need
only be cleaned with a damp cloth.
6) Donotusethisapplianceifanyparthasbeen
under water. Immediately call a qualified
service technician to inspect the appliance
andtoreplacenaypartofthecontrolsystem
and any gas control which has been under
water.
DO NOT use abrasive materials or chemical
cleaners, as they may harm the finish and void
the warranty.
7) In the event this appliance has been
serviced check that the vent-air system
has been properly resealed & reinstalled
in accordance with the manufacturer's
instructions.
Note: Improper positioning of logs may
create carbon build-up and will
severely alter the unit's performance
which is not covered under
warranty.
Clean any fingerprints off before turning
the unit on.
8) Verify operation after servicing.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
43
MAINTENANCE
BAY GLASS REPLACEMENT
DOOR GLASS
INSTALLING VALVE
1) Remove the door from the unit and place on
Your Regency® fireplace is supplied with high
temperature 5mm-Ceramic glass. If your glass
requires cleaning, we recommend using an
approvedglasscleaneravailableatallauthorized
dealers. Do not use abrasive materials.
1) Attach the valve to the valve bracket with
a soft surface to prevent scratching.
the 4 (m5x8 metric) screws provided.
2) Remove the nuts holding the glass clips in
2) Reconnect the "gas out" flare fitting with an
place and remove.
11/16" wrench.
3) Replace the glass. The glass must have
CAUTION & WARNINGS:
3) Reconnect the "gas out" flare nut with a
gasketing around it.
13/16" wrench.
*
Do not clean when the glass is hot.
* Theuseofsubstituteglasswillvoidallproduct
4) Install piezo ignitor push button assembly
warranties.
and reconnect wire.
* Care must be taken to avoid breakage of the
glass.
*
5) Reconnectthequickdropoutthermocouple
Do not strike or abuse the glass.
nut with a 9mm wrench.
* Do not operate this fireplace without the
glass front or with a cracked or broken glass
front.
* Wear gloves when removing damaged or
broken glass.
* Replacement of the glass panel(s) should be
done by a licensed or qualified service per
son.
6) Reconnect the pilot tube nut with a 7/16"
wrench.
7) Scrapeofftheoldgasketfromthefloorofthe
firebox and from the valve tray assembly.
8) Install a new gasket and reinstall the valve
tray assembly.
GLASS REPLACEMENT
Note: Failure to install a new gasket
may severely affect the appliance
performance.
Intheeventthatyoubreakyourglassbyimpact,
purchase your replacement from an authorized
Regency® dealer only.
9) Reinstall the 10 hold down screws.
Replacement glass is shipped already installed
into the door frame. Reinstall as per Glass Door
Installation in "Standard Flush Door" section.
10) Hook up the 2 TP and 2 TH wires to the
appropriate connections on the valve.
11) Reinstallthetwobottomdeflectorsandbrick
CAUTION: Wear gloves when
removing damaged or broken
glass.
panels.
4) Reversetheprevioussteps,replacetheglass
clipsandfastenwiththenutsbutdonotover
tighten, as this can break the glass.
12) Install burner and grate assembly.
13) Hook up the gas line and check for gas
leaks with a soap and water solution or a
gas leak detector. (Do not use open flame
for leak testing.)
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
5) Replace door on the stove and check the
seal.
14) Fire up the unit temporarily.
15) Check the manifold pressure.
16) Reinstall the logs and brick panels as
needed.
17) Close the door and replace the louvers.
18) Fire up the unit again and check for proper
flame appearance and glow on logs.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
44
MAINTENANCE
7) Remove the right and left side deflectors by
REMOVING VALVE
removing the 2 screws on each deflector.
1) Shut off the gas supply.
2) Remove the louvers (and bay door if it has
been installed).
3) Open the flush door and remove the door.
4) Remove the logs and side brick panels, if
installed.
Lift entire valve tray
assembly out.
5) Remove the grate by lifting up and out.
11) Disconnect the 2 TP wires and the 2 TH
wires from the valve.
Right Side
Deflector
12) Undo the pilot tube from the valve with a
7/16" wrench.
13) Undo the quick drop out thermocouple nut
on the valve with a 9mm (metric) wrench.
14) Remove the Piezo igniter wire and push
Grate
button assembly.
6) Remove the burner by removing the screw
on the left side and then slide the burner to
the left and lift out.
Left Side
Deflector
8) Remove the base brick panels.
9) Disconnect the inlet gas line.
10) Removethe10Phillipsheadscrewssecuring
the valve tray assembly in place and then
lift the entire assembly out.
Thermopile Thermocouple
Wire Wire
Pilot Nut
15) Undo the "gas out" flare nut with a 13/16"
wrench.
Remove the screw on the left
side of the burner.
16) Undo the "gas out" flare fitting with an 11/16"
wrench.
17) Remove the 4 Phillips head screws from
the sides of the valve bracket and remove
valve.
Hint:
If you are using black pipe, ensure
that there is a union by the valve,
otherwise removal will be almost
impossible.
Slide the burner to the left and lift out.
Valve Tray
Assembly
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
45
PARTS LIST
MAIN ASSEMBLY
Part #
Description
Part #
Description
1) 948-259 Door Handle
3) 948-046 Chain
4) 948-115 Spring
51) 902-331 Brick Panel - Base Center
52) 902-332 Brick Panel - Base Left
53) 902-333 Brick Panel - Base Right
6) 430-129 Receptacle Box Mount
7) 910-429 Box - Receptacle
8) 910-428 Duplex Receptacle
9) 910-430 Cover - Receptacle
10) 904-687 Clamp Connector
370-901 Brick Panel Set - Standard Brown
370-902 Brick Panel Set - Standard Red
370-903 Brick Panel Set - Herringbone Brown
54)
55)
56)
57)
*
*
*
*
Brick Panel - Back
Brick Panel - Left
Brick Panel - Right
Brick Panel - Top
20) 370-037 Top Nailing Strip
21) 370-038 Side Nailing Strip
22) 370-015 Baffle Plate
946-556 Optional Heat Wave Duct Kit
89) 946-004 Junction Box
90) 946-000 Round Duct Adaptor
91) 946-002 Round to Oval Adaptor
92) 946-001 Oval Duct Adaptor
93) 946-007 Angle Bracket
94) 946-517/P Fan Assembly - HeatWave Option
95) 946-006 Grill Plate - White
96) 946-005/01 Wall Adaptor Plate - White
97) 910-417 Knob - White
98) 910-366 Switch Cover Plate - White
99) 910-412 Fan Speed Controller
23) 780-011 Standoff - Top
24) 780-013 Standoff - Side/Back
27)
28)
29)
30)
*
*
*
*
Outer Flue Collar
Inner Flue Collar Assy
Flue Mounting Plate
Gasket for Flue Collar
35)
*
Thermodisc Bracket
38) 910-241 Switch - Burner ON/OFF(3-way)
910-899 Wire Harness-Valve to Burner
100) 910-367 Box - Plastic Switch Receptacle
101) 690-022 Cover Plate - Outer Box Side
102) 946-010 Flexible Air Duct
432-917 Fan & Speed Control Assy (120 Volts) Optional
42) 910-331/P Fan Motor
946-011 Insulation 6" dia. x 24"
432-966 Fan Switch Assy (120 Volts) Optional
946-570 Heat Release Duct Kit (Optional)
105) 910-165 Fan (120 Volts)
43) 910-813 Power Cord (120 Volts)
46) 910-330 Fan Speed Control Switch
47) 904-586 Knob - Speed Control
48) 910-199 Wire Holder Clip
49) 910-142 Thermodisc - Fan (Auto ON/OFF)
910-845 Wire Harness - Plug In Fan
106) 946-000 Flexible Air Release Duct
372-969 Conversion Kit - NG to LP
918-524 Manual
50) 770-994 Optional Rigid Pipe Adaptor
*Not available as a replacement part.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
46
PARTS LIST
30
28
89
50
93
94
30
20
29
93
27
21
23
92
91
22
96
95
23
102
100
99
24
21
97
98
90
HEAT WAVE DUCT KIT
DOORS & LOUVERS PLEASE
REFER SEPARATE SECTION
10
101
6
7
8
4
3
9
55
57
1
35
24
42
54
106
56
49
48
38
43
47
105
46
52
51
HEAT RELEASE DUCT KIT
53
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
47
PARTS LIST
BURNER & LOG ASSEMBLY
Part #
Description
370-574/P
370-576/P
*
Valve Assembly - Natural Gas
Valve Assembly - Propane
Gasket - Valve Access Plate
52)
56) 910-190
57) 910-478
Piezo Ignitor & Nut
Valve S.I.T. - Natural Gas / Propane
66) 910-038
910-039
Pilot Assy - S.I.T. - 3 Flame NG
Pilot Assy - S.I.T. - 3 Flame LP
Pilot Holder
67)
*
68) W840470
69) 904-662
904-434
Pilot Assembly Gasket
#27 Orifice - N.G.
#47 Orifice - Propane
Orifice Gasket
936-170
75)
*
Valve Access Plate
Burner Assembly
Burner/Grate Assembly
79) 370-535
82) 370-019
90) 910-421
91) 910-422
Pilot ON/OFF Extension Knob
(with Bay Front)
HI/LOW Extension Knob
(with Bay Front)
370-930
P48-2 Log Set
93)
94)
95)
96)
97)
98)
100)
101)
*
*
*
*
*
*
*
*
Center Cross Log
Right Side Cross Log
Front Left Side Log
Front Right Side Log
Left Side End Log
Rear Log
Middle Right Side Log
Right Side End Log
*Not available as a replacement part.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
48
PARTS LIST
FLUSH DOOR & LOUVERS
Part #
Description
Part #
Description
370-925
Flush Louvers (Set) - Steel/Black
Flush Louvers (Set) - Black
Flush Louvers (Set) - Gold/Black
Flush Louver Assembly - Top
Flush Louver Assembly - Bottom
150)
*
Flush Glass Trim
Magnet
370-924
904-196
370-926
*
*
133)
134)
370-933
*
*
Double Screen Door (Complete)
Door Frame Assembly - Left
Door Frame Assembly - Right
Handle
Lift Hinge on Door
Door Latch Assembly
171)
172)
174) 511-085
178) 948-257
180) 512-546
370-518/P
Flush Door Assembly Complete
Glass (Flush)
Flush Door Frame
Glass Gasket (Tadpole)
135) 940-335/P
138)
*
139) 936-155
188) 948-216
Regency® Logo Plate
140) 948-042
Spring Hinge
*Not available as a replacement part.
370-944
370-946
*
*
*
Finishing Trim - Black
Finishing Trim - Steel
Trim Side Left
Trim Side Right
Trim Top
141)
142)
143)
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
49
PARTS LIST
BAY FRONT & LOUVERS
Part #
Description
106) 940-337/P
107) 936-243
108) 940-336/P
Side Glass
Glass Gasket
Center Glass
Brick Panel - Left Side Bay
Brick Panel - Right Side Bay
111)
112)
*
*
113) 370-086
Bay Door Trim (Each) -Black
Bay Louver Assembly - Top
115)
116)
*
*
Bay Louver Assembly - Bottom
Magnet (1" round)
117) 904-196
119) 370-093
120) 400-189
Bay Door Baffle
Flush Glass Retainer Bracket
122) 948-216
Regency® Logo Plate
*Not available as a replacement part.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
50
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Excalibur Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime
Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date
of purchase and parts only thereafter.
Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating
and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks,
ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electricalandmechanicalcomponentssuchasblowers,switches,wiring,thermodiscs,FPIremotecontrols,spillswitches,thermopiles,thermocouples,pilotassemblycomponents,
and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and
continue as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any
item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated
for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty
on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
Regency® P48-2 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
51
FPI fireplaces are designed with reliability and simplicity
in mind. In addition, our internal Quality Assurance Team
carefully inspects each unit thoroughly before it leaves
our door.
FPI FireplaceProductsInternationalLtd.ispleasedtoextend
this Limited Lifetime Warranty to the original purchaser of
a FPI Product.
See the inside back cover for details.
Register your Regency® online at
Installer: Please complete the following information
Dealer Name & Address:______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.:__________________________________________________________
Regency® and Panorama® are trademarks of FPI Fireplace Products International Ltd.
Printed in Canada
© Copyright 2008, FPI Fireplace Products International Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|