P33-3 Zero Clearance
Direct Vent Gas Fireplace
Owners &
Installation Manual
MODELS: P33-NG3 Natural Gas P33-LP3 Propane
WARNING:
FOR YOUR SAFETY
Iftheinformationintheseinstructionsarenotfollowedexactly, What to do if you smell gas:
a fire or explosion may result causing property damage,
personal injury or loss of life.
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fire department.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-262a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
01/04/06
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
P33-3 ZERO CLEARANCE
DIRECT VENT GAS FIREPLACE
Page
Page
Safety Label
Safety Label ............................................................... 4
Installation
Louvers - Flush ........................................................ 29
Double Screen Door................................................. 29
Bay Front (optional).................................................. 29
Bay Trim (optional) ................................................... 29
Louvers - Bay ........................................................... 30
Full Screen Front...................................................... 31
Remote Control (optional) ........................................ 33
Wall Thermostat (optional) ....................................... 33
Remote Wall Switch (optional) ................................. 33
Wiring Diagram......................................................... 34
Fan Installation (optional)......................................... 35
Important Message..................................................... 5
Before You Start ......................................................... 5
General Safety Information ........................................ 5
Manufactured Home Additional Requirements........... 5
Installation Checklist................................................... 6
Unit Dimensions ......................................................... 6
HeatWave Duct System Option.................................. 6
Locating Your Gas Stove............................................ 6
Clearances ................................................................. 7
Combustible Mantel Clearances ................................ 7
Mantel Leg Clearances .............................................. 7
Framing and Finishing................................................ 8
Unit Assembly Prior to Installation.............................. 9
Venting Introduction.................................................... 9
Exterior Vent Termination Locations......................... 10
Venting - Regency Direct Vent System (Flex)
Operating Instructions
Lighting Plate Instructions ........................................ 36
Operating Instructions .............................................. 37
Lighting Procedure ................................................... 37
Shutdown Procedure................................................ 37
First Fire ................................................................... 37
Aeration Adjustment ................................................. 37
Normal Operating Sounds of
Gas Appliances.................................................. 38
Horizontal Terminations only .....................................11
Venting - Installation of Regency Direct Vent
Maintenance
System (Flex)..................................................... 12
Venting - Rigid Pipe Venting Systems...................... 13
Rigid Pipe Venting Components List........................ 14
Venting Arrangements - Vertical Terminations.......... 15
Venting Arrangements - Horizontal Terminations .... 17
Vertical Terminations - Co-Linear Flex System......... 21
Venting Arrangements.............................................. 22
Venting - Horizontal Installations.............................. 23
Venting - Vertical Termination................................... 24
Gas Line Installation................................................. 24
Pilot Adjustment........................................................ 25
High Elevation .......................................................... 25
System Data............................................................. 25
Gas Pipe Pressure Test............................................ 25
SIT Valve Description ............................................... 25
Conversion to Propane............................................. 26
Optional Brick Panels............................................... 27
Log Installation ......................................................... 27
Flush Door - Standard.............................................. 28
Flush Trim (optional)................................................. 28
Maintenance Instructions ........................................ 38
General Vent Maintenance....................................... 38
Gold-Plated or Brass Louvers .................................. 38
Gold Plated or Brass Trim ........................................ 38
Log Replacement ..................................................... 38
Thermopile/Thermocouple ....................................... 39
Glass Gasket............................................................ 39
Door Glass: Flush and Bay Glass ............................ 39
Removing Valve........................................................ 40
Installing Valve.......................................................... 40
Parts List
Replacement/Spare Parts List.................................. 41
Warranty
Warranty................................................................... 47
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABEL
Thisisacopyofthelabelthataccompanieseach
P33-3ZeroClearanceDirectVentGasFireplace.
We have printed a copy of the contents here for
your review. The safety label is located on the
front inside base of the unit, visible when the
bottom louver is open.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is the
correct one.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
10) Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
IMPORTANT:
SAVE THESE
INSTRUCTIONS
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISEDWHEN
THEY ARE IN THE SAME ROOM
AS THE APPLIANCE.
11) Under no circumstances should this ap-
pliance be modified. Parts that have to be
removed for servicing should be replaced
prior to operating this appliance.
The P33-NG3 or P33-LP3 Direct Vent Fireplace
must be installed in accordance with these in-
structions. Carefully read all the instructions in
this manual first. Consult the "authority having
jurisdiction" to determine the need for a permit
prior to starting the installation. It is the respon-
sibility of the installer to ensure this fireplace
is installed in compliance with manufacturer's
instructions and all applicable codes.
CLOTHING OR OTHER FLAM-
MABLE MATERIALSHOULD NOT
BE PLACED ON OR NEAR THE
APPLIANCE.
12) Installationandanyrepairstothisappliance
should be done by a qualified service per-
son. A professional service person should
becalledtoinspectthisapplianceannually.
Make it a practice to have all of your gas
appliances checked annually.
GENERAL SAFETY
INFORMATION
BEFORE YOU START
Safe installation and operation of this appli-
ance requires common sense, however, we
are required by the Canadian Safety Standards
and ANSI Standards to make you aware of the
1) Theapplianceinstallationmustconformwith
localcodesor,intheabsenceoflocalcodes,
with the current Canadian or National
Gas Codes, CAN1-B149 orANSI Z223.1
Installation Codes.
13) Do not slam shut or strike the glass door.
14) Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
INSTALLATION AND REPAIR
SHOULD BE DONE BY A QUALI-
FIED SERVICE PERSON. THE
APPLIANCE SHOULD BE IN-
SPECTED BEFORE USE AND AT
LEASTANNUALLYBYAPROFES-
SIONALSERVICEPERSON.MORE
FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCES-
SIVE LINT FROM CARPETING,
BEDDING MATERIAL, ETC. IT IS
IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS
AND CIRCULATING AIR PAS-
SAGEWAYS OF THE APPLIANCE
BE KEPT CLEAN.
2) The appliance when installed, must be
electrically grounded in accordance with
localcodes,orintheabsenceoflocalcodes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
15) The appliance area must be kept clear and
free of combustible materials, (gases and
other flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.
3) See general construction and assembly
instructions.Theapplianceandventshould
be enclosed.
4) This appliance must be connected to the
specified vent and termination cap to the
outsideofthebuildingenvelope.Nevervent
to another room or inside a building. Make
sure that the vent is fitted as per Venting
instructions.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
DUE TO HIGH TEMPERATURES,
THE APPLIANCE SHOULD BE
LOCATED OUT OF TRAFFIC AND
AWAY FROM FURNITURE AND
DRAPERIES.
5) Inspect the venting system annually for
1) Ensure that structural members are not cut
or weakened during installation.
blockage and any signs of deterioration.
2) Ensure proper grounding using the #8
6) Venting terminals shall not be recessed into a
ground lug provided. See page 34.
wall or siding.
WARNING: FAILURE TO INSTALL
THIS APPLIANCE CORRECTLY
WILL VOID YOUR WARRANTY
AND MAY CAUSE A SERIOUS
HOUSE FIRE.
7) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
CHILDRENANDADULTSSHOULD
BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERA-
TURES, ESPECIALLY THE FIRE-
PLACE GLASS, AND SHOULD
STAYAWAYTOAVOIDBURNSOR
CLOTHING IGNITION.
9) Wear gloves and safety glasses for protec-
tion while doing required maintenance.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLATION
CHECKLIST
UNIT DIMENSIONS
4) The P33-3 can be installed in a recessed
position or framed out into the room as in
A, B, C, D. See Diagram 1.
1) Locate appliance
5) ThisapplianceisListedforbedroom instal-
lations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
a) Room location, page 6
b) Clearances to Combustibles, page 7
c) Mantle Clearances, page 7
d) Framing & Finishing Requirements,
page 8
e) Venting Requirements, pages 10 to
15.
6) The P33-3 Direct Vent Gas Fireplace is ap-
proved for alcove installations, which meet
the clearances listed on this page.
2) Assemble Top Facing Support and Side
Nailing Strips, page 9. (NOTE: must be
done before installing unit into fireplace.)
7) We recommend that you plan your instal-
lation on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have a
qualifiedinspector,dealer,orinstallerreview
your plans before installation.
3) Install vent, pages 10 to 24.
4) Make gas and electrical connections. Test
the pilot. Must be as per diagram. Page 25.
Convert to Propane if desired, page 26.
Note: For vent terminations see page 10.
5) Install brick panels (optional), page 27.
6) Installlogsandembersandrockwoolwhere
indicated on page 27.
7) Install Flush Door Front (Standard) and
optional Flush Gold Trim, page 28.
8) Install optional Double Screen Door, page
29.
9) Install Optional Bay Front and optional Bay
Gold Trim, page 29.
Diagram 1
10) Install Louvers (Flush or Bay), pages 28
and 29.
A)
B)
C)
Flat on Wall
Flat on Wall Corner
Recessed into Wall/Alcove
11) InstalloptionalWallSwitch,RemoteControl,
or Wall Thermostat, page 33.
11) Install Optional Fan, page 35.
13) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is fir-
ing correctly and operation fully explained
to customer.
LOCATING YOUR
GAS STOVE
1) When selecting a location for your stove,
ensure that the clearances outlined on this
page are met.
This includes:
DUCT SYSTEM
OPTION
KIT #946-556
1) Clockingtheappliancetoensurethecorrect
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2) Provide adequate clearances for servic-
ing.
2) Ifrequired,adjustingtheprimaryairtoensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
The HeatWave Air Duct Kit increases the ef-
fectivenessofyourfireplacebydispersingwarm
air from the fireplace to remote locations in the
same room or other rooms in your home.
3) The appliance must be installed on a flat,
solid, continuous surface (e.g. wood, metal,
concrete).Thismaybethefloor,orraisedup
on a platform to enhance its visual impact.
If the appliance is going to be installed on
carpeting, combustible linoleum tile or other
combustible material other than wood floor-
ing, the appliance must be installed on a
metal or wood panel extending the full width
and depth of the appliance.
CAUTION:Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be
operated at one time. This includes the internal
blower option as well.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CLEARANCES
COMBUSTIBLE MANTELS
The clearances listed below are Minimum dis-
tances unless otherwise stated:
Because of the extreme heat this fireplace emits, the mantel clearances are critical. Com-
bustible mantel clearances from top of unit are shown in the diagram below.
A major cause of chimney related fires is
failure to maintain required clearances (air
space) to combustible materials. It is of the
greatest importance that this fireplace and
vent system be installed only in accordance
with these instructions.
Note: A non-combustible mantel may be installed at a lower height if the framing is made
of metal studs covered with a non-combustible board.
Clearance to Combustibles from:
Back
Side
Floor
0"
0"
0"
(0mm)
(0mm)
(0mm)
NOTE: The minimum floor clearance must be
maintained from the top surface of the carpet-
ing, tile, etc.
Minimum Clearance from Top of Unit to:
Mantel*
min. 7" (177mm)
30" (762mm)
Ceiling
from top of unit.
Side Wall Clearance
Bay or Flush Front 7-1/2" (191mm)
Minimum Vent Clearances:
2-1/2" (64mm) Horizontal Top
1-1/2" (38mm) Horizontal Side
1-1/2" (38mm) Horizontal Bottom
1-1/4" (32mm) Vertical Vent Clearance (Simpson)
1-1/2" (38mm) Vertical Vent Clearance (Flex)
Alcove Clearances:
Max. Depth
Min. Width
Min. Height
36"
48"
59"
(914mm)
(1219mm)
(1499mm)
This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded
area or higher using the above scale.
* see mantel clearance instructions.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the
paint may discolour.
WARNING
Firehazardisanextremeriskifthese
clearances are not adhered to.
MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram below:
Maximum
1-1/2" projection at 2"
minimum clearance.
TheHeatWaveDuctKithasdifferentclear-
anceandframingrequirements,checkthe
HeatWave manual for details.
Clearances for Bay or Flush Front
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
FRAMING AND FINISHING
1) Determine the total thickness of facing
material (e.g. drywall plus ceramic tiles) to
allow the finished surface to be flush with
the front of the unit. Total facing thickness
canvaryfrom1/2"(13mm)to1-1/4"(32mm)
thick.
Rear Termination
Simpson Dura-Vent
Minimum Clearances
Simpson Dura-Vent Piping
Top Header
10" (254mm)
dia. Hole through
wall for Dura-Vent
1/2"
(13mm)
Drywall
Install Side Nailing Strips, and Top Facing
Supportbeforeunitisslippedintoposition.
See page 9 for assembly details.
1-1/2"
(38mm)
Flex Piping
16-1/2”
3"
4"
(419mm)
Minimum
(102mm)
(76mm)
Opening for gas
connection
For Both Simpson & Flex
2) Frame in the enclosure for the unit with
Flex Pipe
framing material.
Minimum Clearances
Vertical Termination or
Vertical Rise with Horizontal
Termination
Top Header
10" (254mm)
dia. Hole through
wall for Flex
For Both Simpson & Flex
1/2"
(13mm)
Drywall
NOTE: If this is an outside corner, the minimum
distancebetweentheventandtheoutsidecorner
is6"(15cm)withAstroCapterminationcapor12"
(30cm) with Dura-Vent termination cap.
1-1/2"
(38mm)
3) For exterior walls, insulate the enclosure to
the same degree as the rest of the house,
apply vapour barrier and drywall, as per lo-
cal installation codes. (Do not insulate the
fireplace itself.)
12-3/4”
(324mm)
Minimum
4"
3"
(102mm)(76mm)
Opening for gas
connection
4) The top of the unit must not be closer than
30" (762mm) to the ceiling.
6) Use steel studs for framing where the
1-1/2" (38mm) clearance from the vent
to combustible material cannot be main-
tained.
5) Combustible material may be brought up to
the top and sides of the unit and be covered
with ceramic tiles, bricks, rock or other suit-
able combustible finishing materials.
NOTE: If this is an outside corner, the
minimum distance between the vent and the
outside corner is 6" (15cm) with AstroCap
termination cap or 12" (30cm) with Dura-Vent
termination cap.
Note: Theunitdoesnothavetobecomplete-
ly enclosed in a chase. The clearance
ontopoftheunitis0"tothestandoffs
socombustiblebuildingmaterialscan
belaiddirectlyontopofthestandoffs.
Youmustmaintainclearancefromthe
vent to combustible materials for flex
for Simpson Dura-Vent, see page 7.
TheHeatWaveDuctKithasdifferentclear-
anceandframingrequirements,checkthe
HeatWave manual for details.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
UNIT ASSEMBLY
PRIOR TO INSTALLATION
TheTop Facing Support, the Side Nailing Strips
and the 2 Top Standoffs must be correctly po-
sitioned and attached to the top before the unit
is put into position.
Top Facing Support &
Side Nailing Strips
Determine the total thickness of facing mate-
rial (e.g. drywall plus ceramic tiles) to allow the
finished surface to be flush with the front of the
unit. Total facing thickness can vary from 1/2"
(13mm) to 1-1/4" (32mm) thick.
Top Standoff Assembly
The top standoffs are shipped in a flat position
and must be pulled up and bent into the cor-
rect shape.
The Top Facing Support & Side Nailing Strips
can be mounted in various positions depending
on the thickness of the facing material.
1) Remove the standoffs from on top of the
firebox by undoing the screws.
2) Take each standoff and bend into the cor-
rect shape. Bend up at the bend lines until
the screw holes in the standoff and the
pre-punched screw holes on the firebox top
line-up.
1) Mount Top Facing Support using the 3
supplied screws into the three pre-punched
screwholesonthetopfrontoftheunit.Adjust
support to desired facing material depth.
2) Mount Side Nailing Strip using the 3 sup-
plied screws into the three pre-punched
screw holes at the front sides of the unit.
Adjust support to desired facing material
thickness.
3) Attach the standoffs securely to the top with
4 screws per standoff.
For a facing material depth of
1-1/4"(32mm), the top facing
support must be reversed.
Note: Secure the standoffs to the holes
closest to the edge of the firebox top.
VENTING INTRODUCTION
The P33-3 uses the "balanced flue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer
liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing
warm room air up the chimney.
There are 2 vent systems approved for use with the P33-3: the Regency Direct Vent System (Flex) for Horizontal Terminations only (see pages
11-12), and the Simpson Dura-Vent Systems for Horizontal and Vertical Terminations (see pages 13-24).
Note: These flue pipes must not be connected to any other appliance.
The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid
fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.
NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
EXTERIOR VENT TERMINATION LOCATIONS
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
REGENCY DIRECT VENT SYSTEM (FLEX)
HORIZONTAL TERMINATIONS ONLY
This venting system, in combination with the P33-3 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock
Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram on page 10.
Regency Direct Vent (Flex) System Termination Kit (Part # 946-513) includes all the parts needed to install the P33-3 with a maximum
run of 2 feet. If installing the P33 with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) using Kit # 946-515 (4 ft) or
946-516 (10 ft) or see page 13 for alternate venting arrangements.
1) 6-7/8" dia. flexible liner (2 ft. length)
2) 4" dia. flexible liner (2 ft. length)
3) spring spacers (3)
4) thimble (2)
5) AstroCap termination cap (1)
6) screws (12)
Wall Thimble (2 pc)
(required in
Canada only)
7) tube of Mill Pac (1)
8) plated screws (8)
9) screws #8 x 1-1/2" drill point, stainless steel (4)
AstroCapTM
Termination Cap
(Part# 946-523/P)
4" (102mm)
dia. flue pipe
Notes:
1) Linersectionsshouldbecontinuouswithoutany
joints or seams.
See also
Figure 1 below.
2) Only Flex pipe purchased from Regency may be
used for Flex installations.
spring
spacer
6-7/8"
(173mm)
dia. Flue pipe
Alternate Hori-
zontal Termi-
nation Caps
Important
IfusinganyCabinetMantelswithPart
# 510956, 510958, 510962, 510964
and 510834 the wall thimble must
be secured first and venting must be
attached to unit before sliding into
final position.
AlsoSimpsonDura-Ventventingcan-
not be used with any of the mantels
noted above.
Figure 1
Minimum
Minimum Flex Kit Center-Line
Simpson Dura-Vent Center-Line
Wherever necessary due to
external location of cap, the
AstroCapcanbereplacedwith
theFPIRiserVentTermination
Cap or the Dura-Vent Snorkel
Termination Cap.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLATION PROCEDURES
for Regency Direct Vent System (Flex)
*If this is an outside corner, the minimum distance between the vent and the outside
1) Locate the unit in the framing, rough in the
gas (preferably on the right side of the unit)
and the electrical (Junction block is on the
leftside)ontheleft. Locatethecenterlineof
the termination and mark wall accordingly.
Cut a 10"(254mm) hole in the wall (inside
dimension).
corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent
termination cap. See "F" on the diagram on page 10.
Note: To make the installation more aes-
thetically pleasing, we recommend
framing out a square to mount the
terminal to.
Note: A 2-1/2" (64mm) horizontal top and
1-1/2" (38mm) horizontal sides &
bottom clearance around the liner
must be maintained except that only
a 1" (25mm) clearance is needed at
the termination end. We recommend
framing a 10"(254mm) x 10"(254mm)
(inside dimensions) hole to give
structural rigidity for mounting the
termination.
Minimum and Maximum Vent Clearances
5) Slip the assembled liner and termination
9) Applyabeadofsiliconebetweenthethimble
assembly through the thimble making sure
and termination and around the outer edge
the termination cap faces up (there are
of the terminal at the wall in order to keep
markings on the cap that show which way
the water out.
is up). This will position the termination cap
with proper down slope for draining water.
Fasten the cap to the outer wall with the 4
supplied screws.
IMPORTANT:Donotlocatetermination
hood where excessive snow or ice
buildup may occur. Be sure to check
vent termination area after snow falls,
and clear to prevent accidental block-
age of venting system. When using
snow blowers, make sure snow is
not directed towards vent termination
area.
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination
is not recessed into the siding.
6) Pull the centre 4"(100mm) liner and outer
6-7/8"(175mm) liner out enough to slip over
the flue collars of the fireplace.
7) Apply Mill Pac over the fireplace inner collar
and slip the 4"(100mm) liner down over it
and attach with 3 supplied screws.
2) Level the fireplace and fasten it to the fram-
ing using nails or screws through the nailing
strips.
8) Do the same with the 6-7/8"(175mm) liner.
3) Assemble the vent assembly by applying
Mill Pac to the 4"(100mm) inner collar of the
terminationand slippingthe4"(100mm)liner
over it at least 1-3/8" (35mm). Fasten with
the3screws(drillingpilotholeswillmakethis
easier). Apply Mill Pac or high temperature
silicone to the 6-7/8"(175mm) flex pipe and
slip it over the 6-7/8" outer collar of the vent
terminal at least 1-3/8"(35mm) and fasten
with the 3 screws.
2” x 4” or 2” x 6”
(21mm x 102mm
or 21mm x 152mm)
4" (102mm)
dia. flue pipe
with spring spacer
Termination Cap
Screws
(3 per
connection)
4) Separatethe2halvesofthewallthimbleand
securely fasten the one with the tabs to the
outside wall making sure that the tabs are
on top and bottom. Fasten the other thimble
half to the inside wall. The thimble halves
slip inside each other and can be adjusted
for 2 x 4 or 2 x 6 walls. The liners must slip
over the collars a minimum of 1-3/8".
6-7/8"
(175mm)
dia. air intake
Screws
(4 per connection)
Wall Thimble 2 pieces
(10" (254mm) Outer Diameter)
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic
horizontal termination are:
Vertical
Terminal
1
1
1
1
1
AstroCap Horizontal Termination Cap
45o Elbow
Storm Collar
Flashing
Rigid Pipe Adaptor
Vinyl Siding
Standoff (Optional)
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
For siding other than vinyl furring strips may be
used, instead of the vinyl siding standoff, to create
a level surface to mount the vent terminal. The
Terminal must not be recessed into siding.
Horizontal
Termination
Cap
Ceiling Firestop
Wall Thimble
Adj.Pipe Length
11" - 14-5/8"
(279mm - 372mm)
90o Elbow
If a Vinyl Siding Standoff is required (it must be
used with vinyl siding), measure to outside surface
of wall without siding and add 2 inches.
Pipe Length
Horizontal
Termination Cap
Alternate Hori-
zontal Termi-
nation Caps
24" (610mm)
Pipe Length
Vinyl Siding
Standoff (Optional)
Wall Thimble
Adj.Pipe Length
11" - 14-5/8"
(279mm - 372mm)
45o Elbow
Rigid Pipe Adaptor
WARNING:
Do not combine venting components from
different venting systems.
TM
However use of the the AstroCap and FPI
Riser is acceptable with all systems.
This product has been evaluated by Intertek for
using a Dura-Vent Flue Adaptor in conjunction
with Selkirk Direct-Temp and Ameri Vent Direct
venting systems. Use of these systems with the
DirectVentGSstartingcollarisdeemedaccept-
able and does not affect the Intertek WHI listing
of components.
Flat Wall Installation
Max. Wall
Vent Length
Thickness (inches)
Required (inches)
7-1/4"
9"
6"
10-1/4"
13-1/4"
12"
When using piping other than Simpson
Dura-Vent, 3 screws must be used to
secure rigid pipe to adaptor.
12-1/4" - 15-7/8"
18-1/4" - 25-1/4"
11" - 14-5/8" Adj. Pipe
11" - 14-5/8" Adj. Pipe
The FPI AstroCapTM and FPI Riser Vent terminal is certified for installations using FPI venting systems as well as Simpson Dura-Vent®, Direct Vent GS,
American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPITM, and FPI AstroCapTM are the proprietary trademarks of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RIGID PIPE VENTING COMPONENTS LIST
All Simpson Dura-Vent components are available directly from FPI.
Description
Simpson Dura-Vent
Direct VentGSR
Selkirk
AmeriventR
Direct Vent
Direct-TempTM
6" Pipe Length, Galvanized
6" Pipe Length, Black
908
4DT-6
N/A
908B
N/A
4DT-6B
N/A
N/A
7" Pipe Length, Galvanized
7" Pipe Length, Black
4D7
N/A
907
N/A
4DT-9
4D7B
N/A
9" Pipe Length, Galvanized
9" Pipe Length, Black
907B
906
4DT-9B
4DT-12
4DT-12B
4DT-18
4DT-18B
4DT-24
4DT-24B
4DT-36
4DT-36B
4DT-48
4DT-48B
N/A
12" Pipe Length, Galvanized
12" Pipe Length, Black
4D12
4D12B
N/A
906B
N/A
18" Pipe Length, Galvanized
18" Pipe Length, Black
N/A
904
N/A
4D2
24" Pipe Length, Galvanized
24" Pipe Length, Black
904B
903
4D2B
4D3
36" Pipe Length, Galvanized
36" Pipe Length, Black
903B
902
4D3B
4D4
48" Pipe Length, Galvanized
48" Pipe Length, Black
902B
4D4B
Adjustable Length, 11"-14", Galv.
Adjustable Length, 11"-14", Black
Adjustable Length, 17"-24", Black
Adjustable Length, 7" Galvinized
Adjustable Length, 7" Black
Adjustable Length, 12" Galvinized
Adjustable Length, 12" Black
911
4DT-AJ
4DT-AJB
N/A
N/A
911B
917B
N/A
N/A
N/A
N/A
4D7A
4D7AB
4D12A
4D12AB
N/A
N/A
N/A
N/A
N/A
N/A
45O Elbow, Galvinized
45O Elbow, Black
945
4DT-EL45
4DT-EL45B
N/A
4D45L
4D45LB
N/A
945B
945G
945BG
990
45O Elbow, Swivel, Galvinized
45O Elbow, Swivel, Black
90O Elbow, Galvinized
90O Elbow, Black
N/A
N/A
4DT-EL90S
4DT-EL90SB
N/A
4D90LS
4D90LBS
N/A
990B
990G
990BG
90O Elbow, Swivel, Galvinized
90O Elbow, Swivel, Black
N/A
N/A
Ceiling Support
949 - n/a from FPI
4DT-CS
4DT-CSS
4DT-WS/B
4DT-OS
4DT-WT
N/A
4DT-FS
4DT-TP
N/A
4DFSP
4DRSB
4DWS
N/A
Cathedral Support Box
Wall Support/Band
941
988
Offset Support
Wall Thimble, Black
989 - n/a from FPI
942
940
963
N/A
3951
4DWT
N/A
Wall Thimble Support Box/Ceiling Support
Firestop Spacer
4DFSP
4DFPB
N/A
Trim Plate, Black
Brass Trim for Wall Thimble/Ceiling Support
Attic Insulation Shield 12"
Attic Insulation Shield - Cold Climates 36"
N/A
N/A
N/A
N/A
4DAIS12
4DAIS36
Basic Horizontal Termination Kit (A)
Horizontal Termination Kit (B)
Vertical Termination Kit
970
971
978
4DT-HKA
4DT-HKB
4DT-VKC
4DHTK2
4DHTK1
4DVTK
High Wind Vertical Cap
High Wind Horizontal Cap
Horizontal Square Termination Cap
Verical Termination Cap
Storm Collar
991
985
984
980
953
N/A
N/A
N/A
N/A
4DT-HHC
4DT-HVC
4DT-SC
4DHC
4DVC
4DSC
Adjustable Flashing, 0/12-6/12
Adjustable Flashing, 6/12-12/12
943
943S
4DT-AF6
4DT-AF12
4DF
4DF12
Vinyl Siding Standoff
Vinyl Siding Shield Plate
950
N/A
4DT-VS
4DT-VSP
N/A
N/A
Snorkel Termination 14"
Snorkel Termination 36"
982
981
4DT-ST14
4DT-ST36
4D12S
4D36S
946-506/P
Vent Guard (Optional)
946-208/P
946-523/P
946-206
Vent Guard (Optional) - Riser Vent Terminal
AstroCap Horizontal Cap
Vinyl Siding Standoff - AstroCap
640-530/P
510-994
946-205
Riser Vent Terminal
Rigid Pipe Adaptor (must use with all rigid piping)
Vinyl Siding Shield for Riser Vent Terminal
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations , using one 90o elbow, with
rigid pipe vent systems for Propane and Natural Gas.
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
Note: Must use optional rigid pipe adapter when using rigid pipevent systems (Part # 510-994).
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
The P33-3 is approved for a maximum 40 ft. straight vertical, with rigid pipe
vent systems for Propane and Natural Gas.
The shaded area in the diagram shows all allowable combinations of straight
vertical and offset to vertical terminations with rigid pipe vent systems for
Propane and Natural Gas. Maximum two 45o elbows allowed.
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing
through a wall.
•
Maintain clearances to combustibles.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS
REGENCY DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal
one 90o elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid pipe vent systems. (Refer to page 13.)
A vent guard should be used whenever
the termination is lower than the specified
minimum or as per local codes.
Note: Regency Direct Vent System (Flex) is
onlyapprovedforhorizontaltermina-
tions.
•
•
•
Maintain clearances to combustibles.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
Minimum
Minimum Flex Kit Center-Line
Simpson Dura-Vent Center-Line
Important
IfusinganyCabinetMantelswithPart
# 510956, 510958, 510962, 510964
and 510834 the wall thimble must
be secured first and venting must be
attached to unit before sliding into
final position.
AlsoSimpsonDura-Ventventingcan-
not be used with any of the mantels
noted above.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Horizontal Venting with Two (2) 90o Elbows
Horizontal Venting with Three (3) 90o
Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Option
A)
H
V
H + H1 + H2
3' Max.
5' Max.
6' Max.
7' Max.
Option
A)
V
H + H1
3' Max.
With these options, maxi-
mum total pipe length is 30
feet with minimum of 6 feet
total vertical and maximum
8 feet total horizontal.
Please note minimum 1
foot between 90o elbows
is required.
Withtheseoptions,max.
totalpipelengthis30feet
with min. of 11 feet total
vertical and max. 9 feet
total horizontal.
1 Max. 1' Min.
2' Max. 3' Min.
3' Max. 5' Min.
4' Max. 7' Min.
5' Max. 9' Min.
6' Max. 11' Min.
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
B)
C)
D)
E)
B)
C)
D)
E)
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
Please note min.
1 foot between 90o
elbows is required.
8' Max.
9' Max.
F)
F)
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
H
V
H + H1
With these options, max.
total pipe length is 30 feet
with min. of 8 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
1' Max. 1' Min. 3' Max.
2' Max. 2' Min. 5' Max.
3' Max. 4' Min. 6' Max.
4' Max. 6' Min. 7' Max.
5' Max. 8' Min. 8' Max.
B)
C)
D)
E)
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
V
H
V + V1 H + H1
With these options,
max. total pipe length
is 30 feet with min. of
12 feet total vertical
and max. 9 feet total
horizontal.
2' Min. 1' Max. 3' Min. 4' Max.
3' Min. 2' Max. 4' Min. 5' Max.
4' Min. 3' Max. 6' Min. 6' Max.
5' Min. 4' Max. 8' Min. 7' Max.
6' Min. 5 Max. 10' Min. 8' Max.
7' Min. 6' Max. 12' Min.
B)
C)
D)
E)
Please note min. 1
foot between 90o
F)
9' Max.
elbows is required.
Vertical Venting with Two (2) 90o Elbows
Vertical Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Option H + H1
V
With these options, max. total
pipe length is 30 feet with min.
of6feettotalverticalandmax.
8 feet total horizontal.
Please note min. 1 foot
between 90o elbows is re-
quired.
Withtheseoptions,max.total
pipelengthis30feetwithmin.
of6feettotalverticalandmax.
6 feet total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
Option V
H
V + V1
A)
B)
C)
D)
E)
2' Max. 2' Min.
3' Max. 3' Min.
4' Max. 4' Min.
5' Max. 5' Min.
6' Max. 6' Min.
A)
B)
C)
D)
E)
1' Min. 4' Max. 2' Min.
2' Min. 5' Max. 3' Min.
3' Min. 6' Max. 4' Min.
4' Min. 7' Max. 5' Min.
5' Min. 8' Max. 6' Min.
Foradditionalverticalventingwith2
x 90o elbows, refer to page 15.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
H
V
H + H1 V + V1
With these options, max. total
pipelengthis30feetwithmin.
of 11 feet total vertical and
max. 7 feet total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
1' Max. 1' Min. 3' Max. 3' Min.
2' Max. 2' Min. 4' Max. 5' Min.
3' Max. 3' Min.' 5' Max. 7' Min.
4' Max. 4' Min. 6' Max. 9' Min.
5' Max. 5' Min. 7' Max. 11' Min.
E)
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
V
H + H1 V + V1
With these options, max.
total pipe length is 30 feet
with min. of 10 feet total
vertical and max. 8 feet total
horizontal.
Please note min. 1 foot
between 90o elbows is
required.
2' Min. 3' Max. 4' Min.
3' Min. 4' Max. 6' Min.
4' Min. 5' Max. 7' Min.
5' Min. 6' Max. 8' Min.
6' Min. 7' Max. 9' Min.
7' Min. 8' Max. 10' Min.
B)
C)
D)
E)
F)
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
VERTICAL TERMINATION
WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements on next page for minimum and
maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
Required Parts:
Part #
Description
A maximum
of two certified
joiner kits
may be used
per length.
946-529
Co-linear DV Vertical
Termination Cap
3" Flex - 35 ft.
948-305
946-563
Kit
Co-Axial to Co-Linear Adapter
Flex Liner
which contains the following:
Co-linear Flex Adapter
Outer Pipe
Inner Pipe Adapter
Rigid Pipe Adaptor
#948-305
35 ft (11m)
510-994
945
45o Elbow
Alternate Approved Caps
Exhaust
Flue
980
991
Vertical Termination Cap
High Wind Cap
923GK 3" Co-linear Adapter with flashing
Outer
Pipe
with Kit#
946-563
Air Intake
FPI Cabinet and/or Flat Wall Mantles
may be used in these applications en-
suring that clearances to combustibles
are maintained.
Pipe Length
Co-Linear
Flex
Adapter
with Kit#
946-563
Rigid Pipe Adaptor
# 510-994
45o Elbow
Inner Pipe
Adapter
with Kit#
946-563
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Venting Arrangements - Vertical Terminations
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagrams show the
allowable vertical terminations.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
HORIZONTAL INSTALLATIONS
Install the vent system according to the
manufacturer's instructions included with the
components.
b) Horizontal runs of vent must be sup-
ported every three feet. Wall straps are
available for this purpose.
Diagram 2a
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
5) Mark the wall for a 10" x 10" square hole.
The center of the square hole should line
upwiththecenterlineofthehorizontalpipe.
Cut and frame the 10 inch square hole in
the exterior wall where the vent will be
terminated. If the wall being penetrated is
constructed of non-combustible material,
i.e.masonryblockorconcrete,a7"(178mm)
diameter (7-1/2"(191mm) dia. for flex) hole
is acceptable.
2) Direct Vent pipe and fittings are designed
with special twist-lock connections to con-
nect the venting system to the appliance
flue outlet. A twist-lock appliance adaptor
is an available option that must be used in
conjunction with the Simpson Dura-Vent
Direct Vent GS system.
Below Grade Snorkel Installation
If the Snorkel Termination must be
installed below grade, i.e. basement
application, proper drainage must be
provided to prevent water from enter-
ing the Snorkel Termination. Refer to
Dura-Vent Installation instructions for
details. Do not attempt to enclose the
Snorkelwithinthewall,oranyothertype
of enclosure.
Note:
a) Thehorizontalrunofventmustbelevel,
or have a 1/4 inch rise for every 1 foot
of run towards the termination. Never
allow the vent to run downward. This
could cause high temperatures and
may present the possibility of a fire.
3) Put a bead of silicone inside the outer sec-
tion of the adapter and a bead of Stove
Mate on the inner collar. Slip the adapter
over the existing inner and outer flue collar
and fasten to the outer collar only with the
3 supplied screws (drilling pilot holes will
make this easier). Level the fireplace and
fasten it to the framing using nails or screws
through the nailing strips.
b) Thelocationofthehorizontalventtermi-
nation on an exterior wall must meet all
local and national building codes, and
must not be blocked or obstructed. For
External Vent Terminal Locations, see
diagram on page 9.
6) The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials are
maintained (Dia. 3). Install the termination
cap. AstroCapTM or Dura-Vent Horizontal
Termination Cap may be used.
c) Snorkel Terminations:
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
For installations requiring a vertical rise
on the exterior of the building, 14-inch
and 36-inch tall Snorkel Terminations
and the Riser Vent as shown in Dia. 2 &
2aareavailable.Followthesameinstal-
lation procedures as used for standard
Horizontal Termination. NEVER install
the snorkel upside down.
Note:
a) Twist-lockprocedure:Fourindentations,
locatedon thefemaleendsofpipesand
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends, Dia. 1. Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
arefullylocked.Thefemalelockinglugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
Diagram 3
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
Note: If installing termination on a siding
coveredwall,avinylsidingstandoffor
furring strips must be used to ensure
that the termination is not recessed
into the siding.
Diagram 2
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble (Part # 620-926) over the vent
pipe.
*As specified in CGA B149 Installation Code.
Local codes or regulations may require differ-
ent clearances.
Diagram 1
Note: Applysealant"Mill-Pac"toinnerpipe
and high temperature silicone seal-
ant to outer pipe on every twist-lock
joint.
8) Slide the appliance and vent assembly to-
wards the wall carefully inserting the vent
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
pipe into the vent cap assembly. It is
important that the vent pipe extends into
the vent cap sufficient distance so as to
result in a minimum pipe overlap of 1-1/4
inches.Securetheconnectionbetweenthe
vent pipe and the vent cap 3 sheet metal
screws.
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
Diagram 4
9) Install wall thimble in the center of the
10" square and attach with wood screws
(Diagram 4).
Roof Pitch
Minimum Vent Height
Feet
2
Meters
0.61
0.61
0.61
0.76
0.99
1.22
1.52
1.83
2.13
2.29
2.44
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
2
2
Note: Applysealant"Mill-Pac"toinnerpipe
and high temperature silicone seal-
ant to outer pipe on every twist-lock
joint.
2.5
3.25
4
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/2". Slip the flashing
undertheshingles(shinglesshouldoverlap
half the flashing) as per Diagram 3.
5
6
Diagram 4
7
7.5
8
VERTICAL
TERMINATION
8) Install the vertical termination cap by twist-
locking it.
1) Maintain the 1-1/2" clearances (air spaces)
to combustibles when passing through ceil-
ings, walls, roofs, enclosures, attic rafter,
or other nearby combustible surfaces. Do
not pack air spaces with insulation. Check
pages 13-17 for the maximum vertical rise
of the venting system and the
Note: Any closets or storage spaces, which
the vent passes through must be en-
closed.
GAS LINE
INSTALLATION
maximum horizontal offset
limitations.
Diagram 3: The upper half of the flashing is
installed under the roofing material and not
2) Set the gas appliance in its
desiredlocation. Dropaplumb
bob down from the ceiling to
the position of the appliance
flue exit, and mark the location
where the vent will penetrate
the ceiling. Drill a small hole
at this point. Next, drop a
nailed down until the chimney is installed. This The gas line is brought through the right side of
allows for small adjustments.
the appliance. The gas valve is situated on the
right hand side of the unit and the gas inlet is
on the right hand side of the valve.
6) Continue to assemble pipe lengths.
The gas line connection may be made of rigid
pipe, copper pipe or an approved flex connec-
tor. (If you are using rigid pipe, ensure that the
valvecanberemovedforservicing.)Sincesome
municipalities have additional local codes it is
always best to consult with your local authorities
and the CAN/CGA B149 installation code.
Note: If an offset is necessary in the attic to
avoid obstructions, it is important to
support the vent pipe every 3 feet, to
avoidexcessivestressontheelbows,
andpossibleseparation. Wallstraps
are available for this purpose.
plumbbobfromtheroofto
theholepreviouslydrilled
in the ceiling, and mark
the spot where the vent
will penetrate the roof.
Diagram 1
Galvanizedpipeisdesirableabovetheroofline
duetoitshighercorrosionresistance.Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
heightrequirementsspecifiedinDia.4orlocal
codes. Note that for steep roof pitches, the
vertical height must be increased. A poor
draft, or down drafting can result from high
wind conditions near big trees or adjoining
roof lines, in these cases, increasing the
vent height may solve the problem.
For USA installations follow local codes and/or
the current National Fuel Gas Code, ANSI
Z223.1.
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut
a 10 inch square hole. Frame the hole as
shown in Diagram 2 and install the fire-
stop.
When using copper or flex connectors use only
approved fittings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and flex
connectors are usually considered to meet this
requirement.
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
Important:Alwayscheckforgasleakswitha
soapandwatersolutionorgasleakdetector.
Do not use open flame for leak testing.
Diagram 2
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
PILOT ADJUSTMENT
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.
P33-NG3 System Data
Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile, 1 around
the thermocouple and 1 flowing across the
burner (it does not have to be touching the
burner).
Conversion Kit# 431-969
For 0 to 2000 feet altitude
Burner Inlet Orifice Sizes:
# 4 4
Max. Input Rating 22,500 Btu/h
Min. Input Rating 12,500 Btu/h
Note:
If you have an incorrect flame pat-
For 2000 to 4500 feet altitude
tern,contactyourRegencydealerforfurther
instructions.
Burner Inlet Orifice Sizes:
# 4 5
Max. Input Rating 21,000 Btu/h
Min. Input Rating 10,500 Btu/h
The manifold pressure is controlled by a regu-
lator built into the gas control, and should be
checked at the pressure test point.
Supply Pressure
min.5.0" w.c.
Note: To properly check gas pressure, both
inletandmanifoldpressuresshould
becheckedusingthevalvepressure
ports on the valve.
Manifold Pressure
(High)
3.8"+/- 0.2" w.c.
1) Make sure the valve is in the "OFF" posi-
tion.
P33-LG3 System Data
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a 1/8"
wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#54
Incorrectflamepatternwillhavesmall,prob-
ably yellow flames, not coming into proper
contact with the rear burner or thermopile
or thermocouple.
Max. Input Rating 21,500 Btu/h
Min. Input Rating 10,500 Btu/h
Supply Pressure
min.12.0" w.c.
11"+/- 0.2"w.c.
Manifold Pressure
(High)
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Note: Screw should be
snug, but do not over tighten.
HIGH ELEVATION
This unit is approved in Canada for altitude
to 4500 ft. (CAN/CGA-2.17-M91). For Natural
Gas installations above 4500 ft. follow current
CAN/CGA-B149.1.
S.I.T. VALVE DESCRIPTION
1) Gas cock knob
2) Manual high/low adjustment
3) Pilot Adjustment
4) Thermocouple Connection - option
5) Outlet Pressure Tap
6) Inlet Pressure Tap
7) Pilot Outlet
8) Main Gas Outlet
9) Alternative TC Connection Point
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Conversion Kit from Natural Gas to Propane Model #431-969
for P33-3 using SIT 820 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Conversion Kit Contains:
7) Unscrew the pilot orifice with the allen key
and replace with the LP pilot orifice in the
kit and replace pilot cap.
Qty. Part #
1
Description
910-018 SIT Conversion Kit-50%
Turndown LP
1
1
1
1
1
1
910-037 LP Injector (Pilot Orifice)
904-163 Burner Orifice #54
908-255 Decal "Converted to Propane"
908-528 Red "PROPANE" label
908-529 5/32" Allen Key
908-812 Instruction Sheet
1) Shut off the gas supply.
2) Remove the louvers (and bay door if it is
installed).
3) Open the flush door and remove the door.
4) Remove the logs and embers/rockwool.
8) Remove burner orifice with a 1/2" wrench
and discard. Use another wrench to hold on
to the elbow behind the orifice.
5) Remove the 2 screws holding the Burner
Assembly to the firebox base. Push the
Burner Assembly to the left and lift out.
Burner Orifice
Remove the 2 screws, push Burner
Assembly to the left and lift out.
9) ReinstallnewburnerorificeLPstamped#54
6) Pull off the pilot cap to expose the pilot
and tighten.
orifice.
10) Remove and discard the 3 pressure regula-
tor mounting screws (A), pressure regulator
tower (B) and diaphragm (C).
11) Insure that the rubber gasket (D) is properly
positioned and install the new HI/LO pres-
sure regulator assembly to the valve using
the new screws (E) supplied with the kit.
Tighten screws securely.
14) Replaceyellow"NaturalGas"labelwithred
"Propane" label
15) Check for gas leaks.
12) Reverse steps 5) to 2).
16) Check inlet and outlet pressures.
17) Check operation of flame control.
13) Attach clear label "This unit has been con-
verted to Propane" near or on the serial #
decal. Attach white label "This valve has
been converted from NG to LPG using SIT
conversion Kit Code 0.907.202" onto the
valve.
18) Check for proper flame appearance and
glow on logs.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
OPTIONAL BRICK
PANELS
LOG SET INSTALLATION
D) 251
A) 250
Readtheinstructionsbelowcarefully
and refer to the diagrams. If logs
are broken do not use the unit until
they are replaced. Broken logs can
interfere with the pilot operation.
1) Undo the bottom 2 door latches and open
and remove glass door. Remove logs.
2) Attach the 2 Rear Brick Retaining clips to
the rear wall. Loosen the screws in the top
and rear wall of the firebox and slide the
retainingclipsintoposition(tightagainstthe
firebox top) and then tighten the screws.
Log Kit # 431-930 contains the fol-
The 3-digit numbers (i.e. 250) are
molded into the rear of each log.
B) 254
E) 252
C) 253
4) Place Log 254 on the front right side of the
burner. Push the back of the log against the
2bracketswiththenotchonthebottomright
side of the log fitting into the right side of
the grate.
lowing pieces:
A) 250
B) 254
C) 253
D) 251
E) 252
F)
Rear Log
902-250
902-254
Middle Cross Log
Front Left Cross Log 902-253
Rear Left Log
902-251
Notch
Front Right Cross Log 902-252
Embers
Vermiculite
Rockwool
902-156
902-179/21
902-153
G)
H)
Note: The logs must not be in the unit.
254
3) Insert the back brick panel by carefully slip-
ping it between the back wall of the firebox
and the rear log bracket.
NOTE: If you will be installing the optional
Brick Panels, install the Brick Panels
prior to installing the logs.
1) Carefully remove the logs from the box and
unwrap them. The logs are fragile, handle
with care - do not force into position.
Bracket
Bracket
2) Sprinkle the vermiculite and embers around
the firebox base.
4) Put the side panels in next. Slide them in
from the front and push them flat up against
the wall. Be very careful not to scratch them
on the firebox hardware.
250
254
5) Position Log 253 across the cutouts in Logs
250 and 254 with the notch on the left side
of the log fitting into the 2nd grate tab.
Vermiculite
Vermiculite
Vermiculite
3) Place the Log 250 on the rear log support
pins with the flat side to the back.
Cutouts
253
250
5) Slide the Top Brick Panel into position and
slide the Top Brick Retaining clips so that
they hold the Top Brick Panel in place and
tighten down the screws.
250
254
2nd Grate Tab
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
8) Pull off ember size pieces of rockwool and
gently place them on the front of the burner
trayintheplacesshowninthephotobelow.Do
not compress the rockwool, leave it loose.
250
254
6) Place the bottom left front edge of Log 251
against the left edge of the burner tray and
rest the log on the cutout on Log
253.
Diagram 1
Place rockwool in these 2 locations
on the burner tray.
250
9) Test fire to ensure proper light off (make
sure flame flows smoothly from one end of
burner to the other). If there is any flame
hesitation, checkthatareaforanyblockage
of the burner ports.
251
Diagram 2
254
Use the hook to pull the spring out until you
can put the hook into the slot on the bottom
door bracket. Repeat for 2nd spring. See
diagram 3.
10) Install flush glass and bay glass (if used) as
Cutout
7) PositionLog252acrossthecutoutsin Logs
254 and 253. The notch in the bottom right
end fitting against the 5th grate tab.
STANDARD FLUSH
DOOR
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, diagram 1. Be care-
ful that the glass gasket does not roll up; there
must be a gap between the gasket and the door
lip to ensure that the door sits securely on the
unit. Diagram 2.
Diagram 3
To remove the flush door, reverse the above
steps.
Optional Flush Trim
Attach the round magnets to the back of the top
trim piece and to the bottom trim piece, then at-
tach trim to the top and bottom of Flush door.
254
5th Grate Tab
250
251
254
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
DOUBLE SCREEN
DOOR
FLUSH LOUVERS
1) Install the top louver by sliding the two
bracket clips into the brackets located un-
derneath the top of the firebox.
1) Pull out the top louver.
2) Center the screen door and hook over the
flush door.
2) Installthebottomlouverbyfoldingthelouver
down and then sliding the Bottom Louver
bracket down onto the 2 pins on the base
of the unit (dia. 1). Secure with 1 screw as
per dia. 2.
Diagram 1
Diagram 2
3) Open the screen door(s) and secure the
screen door to the flush door front with 2
clips on the bottom left and right side.
Note:Ifanymaintenance etc. mustbedone
in the firebox, first remove the Bay
louvers and door.
Note: Top and
bottom louvers
are different.
Optional Bay Trim
Clip locations
Attach 4 supplied magnets each to the back of
the top and bottom trim pieces, and attach trim
to the top and bottom of Bay door.
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace and position the slots in the
bracket over the 2 screws on the left side of
the bottom louver. Push down to lock into
place. Tighten the screws.
Clip installed on right side.
OPTIONAL BAY DOOR
The Bay louvers MUST be used
with the Bay glass option.
The optional Bay door is an overlay on the
flush front. The standard flush door and glass
must remain on the unit.
Burner ON/OFF
control box
Screws on lou-
ver bracket
1) Hook the top of the bay door over the flush
door flange and swing the bottom against
the bottom flange of the flush door.
2) Secure to the flush door bottom bracket with
2 screws provided.
3) Slide the valve extension knobs onto the
valve knobs.
Burner ON/OFF control box attached to bot-
tom flush louver.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
BAY LOUVERS
1) Remove flush louver top heat shield by removing the 4 screws.
4) Install bottom louver by sliding the two bracket clips into the brackets
located underneath the bay door. Secure with 1 screw into each
Bottom Louver Mounting Bracket as per diagram below. Use the
bottom hole in the bracket.
5) Slide the valve extension knobs onto the valve knobs. Match the
correct ext. knob with the valve knob.
Flush Louver Top
Heat Shield
2) Install the bay louver top heat shield and secure with 4 screws.
6) Open the bottom louver. Pull the Burner ON/OFF control box from
inside the bottom of the fireplace and position the slots in the bracket
over the 2 screws on the left side of the bottom louver. Push down
to lock into place. Tighten the screws.
Burner ON/OFF
control box
Bay Louver Top
Heat Shield
3) Install top louver by sliding the two bracket clips into the brackets
located on top of the bay door. See below. The fitted louver leaves
a small gap between faceplate bottom and louver top.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
FULL SCREEN FRONT
1) Before beginning the installation, remove the Glass Door from the
4) a)
Before attaching the Full Screen Door Frame to the unit,
loosen the left and right side #8 Self Tapping Philips screws
located on the inside top of the outer frame of the appliance.
Also remove the center screw.
unit. Refer to the manual for instructions.
2) Slide the Bottom Face Plate Bracket into the bottom of the unit,
secure it into the pins located on the inside of the fire box. Once the
bracket is in place, tighten the screws into the hinges on the left and
right sides.
b)
Slide the cut-outs in the Top and Bottom Flange of the Full
Screen Door Frame under the screw heads which were
loosened in step 4a). Once the Frame is in place, tighten
the screws to secure. Also re-secure the top center screw
through the oblong hole.
Full Screen Door
Frame
BottomFaceplate
Bracket
Pin location
Cut-Out
Oblong Hole
Faceplate
Mounting
Bracket
Screw
Cut-Out
Top
Flange
Bottom
Flange
Backside of Full
Screen Door
Frame Shown
3) Before attaching the Full Screen Door Frame, remove the Screen
Doors from the Full Screen Door Frame by fully opening the doors
and lifting up off of the hinges. See important note in step 10.
Cut-Outs
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
NOTE: Should the finished wall protrude beyond the face of the unit, 8) Re-install Glass Door. Refer to the manual for instructions.
you can accommodate up to 1/2" depth.
9) Slide the Top Grill into the louver brackets located on the inside top
of the firebox. Push in place.
Simply push in the Full Screen Door Frame until it aligns against
the finished wall. Secure Top Flange of Full Screen Door Frame as
described in step 4 b).
For the Bottom Flange of the Full Screen Door Frame, push the bot-
tom of the Frame until it aligns with the wall. Use the inner cut-outs to
secure the base of the Frame using the 2 x #8 Self Tapping Phillips
screws provided.
5) Install the Hinges to the Hinge Brackets on the left and right side of
the Bottom Faceplate Bracket (seen in step 2), secure using 2 x #8
Self Tapping Philips screws per hinge.
Top Grill
6) Place the Bottom Frame near the hinges, and flip down the hinges
from the Bottom Face Plate. Secure the hinges in place to the Bottom
Frame, using 2x #8 Self Tapping Phillips screws per hinge.
10) Install the Left and Right Side Screen Doors in the fully open position
by placing over top of the hinges on the Full Screen Door Frame.
NOTE: Failure to install the doors in the fully open position could
result in paint damage to the surface of the door.
Hinge Location
Bottom Grill
Hinge
7) Mount the Burner ON/OFF Control Box to the left side of the Bottom
Grill using 2 x #8 - 1/4" Philips Head Screws.
Left Side
of Bottom
Grill
Screen Door
Burner ON/OFF
Control Box
11) Close screen doors.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
OPTIONAL
OPTIONAL
OPTIONAL
WALL SWITCH
REMOTE CONTROL
WALL THERMOSTAT
1) Runthesupplied15'ofwirethroughtheright
or left side gas inlet opening. Be careful not
to damage wire.
UsetheRegencyRemoteControlKit approved
for this unit. Use of other systems may void
your warranty.
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram.
Use table below to determine the maximum
wire length.
Note: We recommend a maximum of 15'
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
The remote control kit comes with a hand
held transmitter, a receiver and a wall mount-
ing plate.
Note: Preferableifthethermostatisinstalled
on an interior wall.
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use Thermostat Wire Table.
2) Connectthewiretothesuppliedwallswitch
and install into the receptacle box.
Regency offers an optional programmable
thermostat but any 250-750 millivolt rated non-
anticipator type thermostat that is CSA, ULC or
UL approved may be used.
CAUTION
Do not wire millivolt
wall switch wire
to 120V wire.
2) Connect the two wires to the gas valve.
See diagram below.
CAUTION
Do not wire millivolt
wall thermostat wires
to 120V wire.
CAUTION
Do not wire millivolt
remote control wires
to 120V wire.
Thermostat Wire Table
3) Install3AAAalkalinebatteriesintransmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
WIRING DIAGRAM
This heater does not require a 120VA.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat
will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.
(Do not cut the ground terminal off under any circumstances.)
NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit)
in case the fan is installed at a later date.
Lockwasher
Star washer
Fan
Ground
#8 Ground Lug
(mobile home
approved)
Neutral
Live
Green
OFF
Ground
ON
120V AC
60 Hz
Pilot
Assembly
Black
Red
Red
Nut
Minimum Convection
Air Temp. Switch
Rotary Speed
Control
Fan
ground wire
Piezo
Ignitor
White
(To THTP)
(To TH)
ON
Burner
OFF
Thermostat
Brown
White
F
Gas
In
Red
Black
To Thermocouple IN
"S.I.T" Valve
T-Stat
ON OFF
Remote Receiver
or Thermostat
(Millivolt) (Optional)
Remote Transmitter
(Optional)
Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.
CAUTION: Labelallwires
prior to disconnection
when servicing controls.
Wiring errors can cause
improper and dangerous
operation.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
INSTALLING THE OPTIONAL FAN
120 Volt AC power is needed for the fan switch
andblower.Thefancanbehardwiredifdesired.
The receptacle box should be installed on the
left hand side of the unit by a qualified electri-
cian. The neutral (wider) slot of the polarized
receptacle should be at the top.
11) Attach the two control boxes to the bottom
louver and tighten the 2 screws on the left
side and 1 screw on the right side.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
1) Shut the power off.
Diagram 2
2) Remove the standard flush door and the
optional bay door, if installed. Open the
bottom louver door.
Secure left side with 2 screws.
3) Loosen the 2 screws holding the Burner
ON/OFF switch and bracket to the bottom
louver and lift the assembly out.
Diagram 3: Use the clip & hook on the side of
the control boxes to join them together.
8) Secure the two boxes together with one
screw.
Secure right side with one screw.
4) Turn the fan base on its side (with the base
facing towards you) and then slide the fan
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs.Takecarenottodamagetheinsulation
onthefanbase.Ensurethatthefanblades
do not rub against the valve tubing.
Diagram 1.
12) Secure the fan wires and power cord by
attaching one of the adhesive backed wire
holder clips (Part #910-199) onto the stove
base. Use the second clip to bundle up the
wiresapproximately4"fromthecontrolbox.
Ensure that there is no interference with the
wires when the louver is closed and that
no wire will touch the hot metal surfaces or
sharp edges.
Secure the 2 boxes together
with one screw.
9) Position the control box assembly on the
bottom louver and mark the position of the
slot on the right side bracket.
5) Connect fan ground cable to ground lug.
Refer to wiring diagram.
13) Plug the fan power cord into the rear end of
the receptacle box to provide the maximum
clearance from the louvers.
6) Slide the thermodisc/cover assembly into
the bracket clip on the underside of the
firebox. Check that no wire will touch the
hot surfaces. Diagram 2.
TO REMOVE THE FAN
1) Shut the power off.
7) Attach the Fan control box to the Burner
ON/OFF control box. Diagram 3.
Hold control box assembly in place and
mark the position of the right side slot
2) Reverse the above instructions.
10) Removethecontrolboxassemblyandpush
thehold-downclipontothelouver. Bendthe
tab until it is at 90o to the louver.
Note: The bearings are lubricated for life.
Do not lubricate them. Make sure
you vacuum the fan area on a regular
basis.
IMPORTANT:
These fans collect a lot of dust from within
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a soft
brush nozzle.
Push hold-down clip onto inside
louver and press tab until it is
at 90o to
louver.
Diagram 1
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
COPY OF THE LIGHTING PLATE INSTRUCTIONS
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
4) When the pilot stays lit, turn the gas knob
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
OPERATING
INSTRUCTIONS
further counterclockwise to the "ON" posi-
tion.
1) Read and understand these instructions
During the first few fires, a white film may
developontheglassfrontaspartofthecuring
process. The glass should be cleaned or the
film will bake on and become very difficult
to remove. Use a non-abrasive cleaner and
NEVER clean the glass while it is hot.
5) Use the wall switch, thermostat or remote
before operating this appliance.
control to turn on the unit.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
6) Rotate the flame height regulator to adjust
the flame height higher or lower.
3) Check to ensure there are no gas leaks.
4) Make sure the glass in the door frame is
properly positioned. Never operate the ap-
pliance with the glass removed.
AERATION
ADJUSTMENT
5) Verify that the venting and cap are unob-
structed.
The air shutter can be adjusted by moving the
adjustingwireupordown.Thewireisaccessed
throughthebottomlouveropening.Opentheair
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but
may need adjusting due to either the local gas
supply or altitude.
6) Ensure that the brick panels are installed.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
Minimum Air Shutter Opening:
3/16"
3/8"
Natural Gas
Propane
SHUTDOWN
PROCEDURE
LIGHTING PROCEDURE
CAUTION:Carbonwillbeproducedifairshutter
is closed too much.
1) Use the wall switch, thermostat or remote
control to turn off the main burner.
IMPORTANT
2) Turn the main gas control clockwise to the
To ignite or reignite the pilot,
you must first release the ten-
sion springs below the door.
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
Air
shutter
service is to be performed.
Only when the pilot holds, without pressure
being applied to the control knob, reapply the
tension springs to the door. The unit must
not be operated with the tension springs
unattached.
FIRST FIRE
The first fire in your stove is part of the paint cur-
ing process. To ensure that the paint is properly
cured, it is recommended that you burn your
fireplace for at least four (4) hours the first time
you use it with the fan on.
IMPORTANT:Gascockknobcannotbeturned
from "PILOT" to "OFF" unless it is partially
depressed.
wire
Adjustment Wire: push to close
or pull to open aeration cap
Closed - Tall yellow
Whenfirstoperated,theunitwillreleaseanodour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at this
time. Open a few windows to ventilate the room
for a couple of hours.
1) Turn burner OFF using "ON/OFF" switch.
Open - Short blue
2) Turn gas control knob so indicator points to
"OFF" position and allow 5 minutes for any
gas in the combustion chamber to escape.
Note: Anydamageduetocarboningresult-
ing from improperly setting the aera-
tion controls is NOT covered under
warranty.
The glass panel may require cleaning after the
unit has cooled down. DO NOT ATTEMPT TO
CLEAN THE GLASS WHILE IT IS HOT.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the igniter button several times until the
pilot lights. After approximately one minute,
releasethegascontrolknob.Thepilotflame
should continue to burn. If the pilot does not
remainlit,repeatoperationallowingalonger
period before releasing gas control knob.
Note: Aeration Adjustment should only be
performedbyanauthorizedRegency
Installer at the time of installation or
service.
Note: When the glass is cold and the appli-
anceislit,itmaycausecondensation
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3) Checkforevidencesofexcessivecondensa-
tion, such as water droplets forming in the
innerliner,andsubsequentlydrippingoutthe
joints, Continuous condensation can cause
corrosion of caps, pipe, and fittings. It may
be caused by having excessive lateral runs,
toomanyelbows,andexteriorportionsofthe
system being exposed to cold weather.
NORMAL OPERATING
SOUNDS OF
MAINTENANCE
INSTRUCTIONS
1) Alwaysturnoffthegasvalvebeforecleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
GAS APPLIANCES
It is possible that you will hear some sounds
fromyourgasappliance.Thisisperfectlynormal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listedbelowaresomeexamples.Allarenormal
operating sounds and should not be consid-
ered as defects in your appliance.
4) Inspect joints, to verify that no pipe sections
or fittings have been disturbed, and conse-
quently loosened. Also check mechanical
supports such as Wall Straps, or plumbers'
tape for rigidity.
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
Blower:
Regency gas appliances use high tech blow-
ers to push heated air farther into the room. It
is not unusual for the fan to make a "whirring"
sound when ON. This sound will increase or
decrease in volume depending on the speed
setting of your fan speed control.
GOLD-PLATED or
BRASS LOUVERS/TRIM
The 24 carat gold-plated or brass finish on the
louvers and trim requires little maintenance,
and need only be cleaned with a damp cloth.
DO NOT use abrasive materials or chemical
cleaners, as they may harm the finish and void
thewarranty. Cleananyfingerprintsoffbefore
turning the unit on.
3) The heater is finished in a heat resistant
paintandshouldonlyberefinishedwithheat
resistant paint. Regency uses StoveBright
Paint - Metallic Black #6309.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a differ-
ent gauge material from the rest of the firebox
and body. Therefore, the varying thicknesses
of steel will expand and contract at slightly
different rates which can cause "ticking" and
"cracking" sounds. You should also be aware
that as there are temperature changes within
theunitthesesoundswilllikelyre-occur.Again,
this is normal for steel fireboxes.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flameoftheburnerperiodically,makingsure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
LOG REPLACEMENT
5) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
Blower Thermodisc:
When this thermally activated switch turns ON
itwillcreateasmall"clicking"sound.Thisisthe
switch contacts closing and is normal.
Note:
Never operate the appliance without
the glass properly secured in place.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
6) Donotusethisapplianceifanyparthasbeen
under water. Immediately call a qualified
service technician to inspect the appliance
andtoreplacenaypartofthecontrolsystem
and any gas control which has been under
water.
Note: Improperpositioningoflogsmaycre-
ate carbon build-up and will severely
alter the unit's performance which is
not covered under warranty.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dullclickingsoundmaybeaudible,thisisnormal
operation of a gas regulator or valve.
7) Verify operation after servicing.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
General Vent Maintenance
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or streaks,
and in extreme cases, holes. These com-
ponents should be replaced immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Bay Glass Replacement
Flush Glass Replacement
THERMOPILE/
1) Remove the door from the unit and place on
THERMOCOUPLE
Remove the flush door front. Remove the 4
glass clips from each corner. Slide in the new
replacement glass. Push the 4 glass clips back
onto the frame. The glass must have gasket-
ing around it.
a soft surface to prevent scratching.
1) Open the bottom louvers.
2) Remove the nuts holding the glass clips in
place and remove.
2) Loosenthethermocoupleorthermopilewith
a 7/16" wrench.
3) Replace the glass. The glass must have
gasketing around it.
3) Disconnect thermocouple by loosening nut
from the valve with a 9mm wrench. Dis-
connect thermopile by loosening 2 screws
marked TP on the valve.
5) Reversetheprevioussteps,replacetheglass
clips and fasten with the nuts but do not over
tighten, as this can break the glass.
4) Drop the thermocouple or thermopile down
6) Replace door on the stove and check the
from the bracket and pull it out of the unit.
seal.
5) Reinstall the new ones in reverse order.
GLASS GASKET
If the glass gasket requires replacement use
5/8" flat glass gasket for the Bay Front (Part
# 936-243) and a tadpole glass gasket for the
Flush Front (Part # 936-155).
DOOR GLASS
Your Regency stove is supplied with high
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your
unit will produce. If your glass requires clean-
ing, we recommend using an approved glass
cleaner available at all authorized dealers. Do
not use abrasive materials. Do not clean the
glass when hot.
Intheeventthatyoubreakyourglassbyimpact,
purchase your replacement from an authorized
Regencydealeronly,andfollowourstep-by-step
instructions for replacement.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
Caution:Weargloveswhenremoving
damaged or broken glass.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REMOVING VALVE
1) Shut off the gas supply.
INSTALLING VALVE
10) Undo the pilot tube from the valve with a
7/16" wrench.
1) Attach the valve to the valve bracket with
the 4 (m5x8 metric) screws provided.
2) Remove the louvers (and bay door if it is
on).
2) Reconnect the "gas out" flare fitting with
an 11/16" wrench.
3) Open the flush door and remove the door.
3) Reconnect the "gas out" flare nut with a
4) Remove the logs.
13/16" wrench.
5) Remove the burner/grate assembly by
removing the two Phillips head screws and
then lift the burner assembly out.
4) Install piezo ignitor push button assembly
and reconnect wire.
5) Reconnectthequickdropoutthermocouple
nut with a 9mm wrench.
Diagram 3: Lift out Valve Tray Assembly
6) Reconnect the pilot tube nut with a 7/16"
wrench.
7) Scrapeofftheoldgasketfromthefloorofthe
firebox and from the valve tray assembly.
8) Install a new gasket and reinstall the valve
tray assembly.
Note: Failure to install a new gasket may
severely affect the appliance per-
formance.
11) Undo the quick drop out thermocouple nut
on the valve with a 9mm (metric) wrench.
9) Reinstall the 10 hold down screws.
12) Remove the Piezo igniter wire and push
button assembly.
10) Hook up the 2 TP and 2 TH wires to the
appropriate connections on the valve.
Diagram 1: Remove the left and right screws
and then lift out the burner/grate assembly.
13) Undo the "gas out" flare nut with a 13/16"
wrench.
11) Reinstall the front log stand.
6) Remove the rear log stand by removing the
14) Undo the "gas out" flare fitting with an 11/16"
2 screws.
12) Install Burner/grate assembly.
wrench.
7) Disconnect the inlet gas line. See diagram
13) Hook up the gas line and check for gas
leaks with a soap and water solution or a
gas leak detector. (Do not use open flame
for leak testing.)
15) Remove the 4 Phillips head screws from
the sides of the valve bracket and remove
valve.
2.
8) Disconnect the 2 TP wires and the 2 TH
wires from the valve.
Hint: If you are using black pipe, ensure that
there is a union by the valve, otherwise removal
will be almost impossible.
14) Fire up the unit temporarily.
9) Remove the 10 Phillips head screws secur-
ingthevalvetrayassemblyinplace(diagram
2) and then lift the entire assembly out
(diagram 3).
15) Check the manifold pressure.
16) Reinstall the logs and brick panels as
screws
Rear Log Stand
needed.
17) Close the door and replace the louvers.
18) Fire up the unit again and check for proper
flame appearance and glow on logs.
Valve Tray Assembly
Diagram 2: Rear Log Stand & Valve Tray Assembly
screws
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Main Assembly
Part # Description
Part #
Description
Part #
Description
49) 910-142
50) 904-713
432-967
Thermodisc - Fan Auto ON/OFF
U-Clip at Louver
1) 948-247 Door Handle
432-928 Brick Panel Set - Standard
432-901 Brick Panel Set - Standard Brown
432-902 Brick Panel Set - Standard Red
432-903 Brick Panel Set - Herringbone
Brown
2)
*
Thermodisc Bracket
Burner On/Off Switch Assy
Switch - Burner On/Off
63) 910-241
910-899
7) 910-428 Duplex Receptacle
8) 910-429 Box - Receptacle
9) 910-430 Cover - Receptacle
10) 904-687 Clamp Connector
13) 948-045 #12 Jack Chain
14) 948-115 Door Extension Spring
Wire Harness - Valve to Burner
432-904 Brick Panel Set - Herringbone Red
946-556
89) 946-004
90) 946-000
91) 946-002
92) 946-001
93) 946-007
Optional Heat Wave Duct Kit
Junction Box
Round Duct Adaptor
Round to Oval Adaptor
Oval Duct Adaptor
Angle Bracket
33) *
Brick Panel - Rear
34) *
35) *
36) *
Brick Panel - Left Side
Brick Panel - Right Side
Brick Panel - Top
16) *
17) *
Thermodisc Top
37) 430-056 Brick Clip - Top
38) 430-057 Brick Clip - Bottom
Thermodisc Box Base
94) 946-517/P Fan Assembly - HeatWave
Option
19) 430-129 Receptacle Box Mount
432-945 Herringbone Brick Panel Set
(Optional)
902-359 Brick Panel - Rear
902-358 Brick Panel - Left Side
902-360 Brick Panel - Right Side
902-361 Brick Panel - Top
95) 946-006
96) 946-005
97) 910-417
98) 910-366
99) 910-412
Grill Plate - White
20) 430-031 Top Nailing Strip
21) 430-032 Side Nailing Strip
22) 433-017 Firebox Baffle
23) 433-011F Top Standoff
24) 511-044 Standoff - Side
790-091 Standoff - Rear
Wall Adaptor Plate - White
Knob - White
Switch Cover Plate - White
Fan Speed Controller
100) 910-367 Box - Plastic Switch
Receptacle
26) *
27) *
28) *
30) *
31) *
Louver Hold Down
102) 946-010 Flexible Air Duct
Outer Flue Collar
432-917 Fan Assembly (120 Volts)
Optional
42) 910-331/P Fan Motor (120 Volts)
432-966 Fan Switch Assy (120 Volts)
43) 910-813 Power Cord (120 Volts)
46) 910-330 Fan Speed Control
47) 904-586 Knob - Speed Control
946-038
Insulation 6" dia. x 24"
Inner Flue Collar Assembly
Gasket - Flue Collar
Flue Mounting Plate
104) 690-022F Cover Plate
510-994
918-262
431-969
Dura-Vent Adaptor
Manual
Conversion Kit - NG to LP
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Burner & Log Assembly
Part
Description
53) 430-055
54) 910-421
55) 910-422
56) 910-190
Gasket - Valve Access Plate - NG/LP
Pilot ON/OFF Extension Knob
Flame HI/LOW Extension Knob
Piezo Ignitor and Nut
433-574/P
433-576/P
57) 910-378
910-380
Valve Assy - Natural Gas
Valve Assy - Propane
S.I.T. Valve - Natural Gas
S.I.T. Valve - Propane
Valve Bracket
58) *
59) *
60) *
Firebox Base
Valve Tray
66) 910-038
910-039
Pilot Assy - 3 way flame - S.I.T. - NG
Pilot Assy - 3 way flame - S.I.T. - LP
Orifice #44 - Natural Gas
Orifice #54 - Propane
Orifice Gasket
904-568
904-163
936-170
67) *
Pilot Holder
68) W840470
79) 433-525
82) 433-024
83) *
85) 431-930
86) 430-097
87) 433-018
Pilot Assembly Gasket
Burner Assy - NG/LP
Burner Grate Assembly - NG/LP
Rear Log Support Bracket - NG/LP
Log Set
Air Deflector-Left
Air Deflector-Right
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Flush Front & Louvers
Part #
Description
Part #
Description
117) 904-196
130) 430-924
131) 430-926
430-947
Magnet - 1' round
430-940
Finishing Trim (Set) - Black (Option)
Finishing Trim (Set) - Brass (Option)
Finishing Trim Left
Flush Glass Trim (set) - Gold (Option)
Flush Glass Trim (set) - Brass (Option)
Flush Glass Trim (set) - Brushed Steel (Option)
430-942
157)
159)
158)
*
*
*
Finishing Trim Right
Finishing Trim Top
430-918
430-920
430-922
430-923
Flush Louvers (set) - Gold/Black (Option)
Flush Louvers (set) - Brass/Black (Option)
Flush Louvers (set) - Black (Option)
Flush Louvers (set) - Black/Steel (Option)
Flush Louver Assy-Top
Front Deflector
Flush Louver Assy-Bottom
431-943
*
*
Double Screen Door Complete (Option)
Door Frame Left Assembly
Door Frame Right Assembly
U-Clip for Frame
Door Handle
Door Latch
Door Support Frame Assembly
Pushnut Fastener 3/16"
Screw - #8 x 1/2"
171)
172)
133)
134)
*
173) 904-712
174) 430-133
175) 511-084
430-162
*
178)
*
433-538
Flush Door Assembly Complete
Glass (Flush)
U-Clip
Glass Gasket (Tadpole)
Spring Hinge - Black
904-715
*
135) 940-088/P
137) 904-691
139) 936-155
140) 948-042
179) 948-216
Regency Logo Plate
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Bay Front & Louvers
Part #
Description
430-930
106) 940-079/P
107) 936-243
108) 940-078/P
Bay Front Complete
Side Glass
Glass Gasket
Center Glass
Bay Door Frame
110)
*
111) 902-322
432-905
Bay Brick Panel - Standard
Bay Brick Panel - Standard Brown
Bay Brick Panel - Standard Red
Bay Brick Panel Spacer
Magnet (1" round)
432-906
112)
*
117) 904-196
118)
*
Louver Hold Down
Glass Retainer
120) 400-189
432-956
432-954
432-958
Bay Door Trim (set) - Gold
Bay Door Trim (set) - Brass
Bay Door Trim (set) - Brushed Steel
Bay Door Trim (each) - Black
123)
*
430-932
430-934
430-936
430-937
*
Bay Louvers (set) - Gold/Black
Bay Louvers (set) - Brass/Black
Bay Louvers (set) - Black
Bay Louvers (set) - Steel/Black
Bay Louver Assy-Top
Bay Door Deflector
125)
126)
433-026
*
Bay Louver Assy-Bottom
Hinge
129) 948-042
130) 432-960
131) 948-216
Bay Front Screen
Regency Logo Plate
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Regency Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime
Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date
of purchase and parts only thereafter.
Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating
and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks,
ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electricalandmechanicalcomponentssuchasblowers,switches,wiring,thermodiscs,FPIremotecontrols,spillswitches,thermopiles,thermocouples,pilotassemblycomponents,
and gas valves are covered for one year parts and subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue
as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated
for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from Regency, may nullify your
warranty on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Download from Www.Somanuals.com. All Manuals Search And Download.
Regency fireplace products are designed
with reliability and simplicity in mind.
Inaddition,ourinternalQualityAssurance
Team carefully inspects each unit
thoroughly before it leaves our
door.
FireplaceProductsInternational
Ltd. is pleased to extend this
Limited Lifetime Warranty to the
original purchaser of a Regency
Product.
See the inside back cover for details.
Register your Regency online at
Installer: Please complete the following information
Dealer Name & Address:______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.:__________________________________________________________
Regency and Panorama are trademarks of FPI Fireplace Products International Ltd.
© Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|