RMS9-99101(003)
OWNER/OPERATOR MANUAL
SWEEPER
RMSZ2500
WARNING
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Before using our products, please
read this manual carefully to
understand the proper use of your
unit.
APPLICABLE SERIAL NUMBERS :
DRIVE UNIT 900101 and up SWEEPER UNIT 000000 and up ENGINE UNIT 009766 and up
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
Instructions contained in warnings within this
manual marked with a
symbol concern
critical points which must be taken into
consideration to prevent possible serious
bodily injury, and for this reason you are
requested to read all such instructions
carefully and follow them without fail.
■ WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions which must be
followed in order to prevent accidents which could
lead to serious bodily injury or death.
IMPORTANT
This mark indicates instructions which must be
followed, or it leads to mechanical failure,
breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the
use of the product.
CONTENTS
1. Parts location …………………………………4
2. Specifications …………………………………5
3. Warning labels on the machine ……………6
4. Symbols on the machine ……………………7
5. For safe operation ……………………………8
6. Set up…………………………………………14
7. Fuel……………………………………………16
8. Operation ……………………………………18
9. Maintenance …………………………………23
10. Storage ………………………………………28
11. Troubleshooting guide………………………28
12. Parts list ………………………………………29
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Parts location
1. Loop Handle
2. Shoulder Strap Hanger
3. Ignition Switch
4. Throttle Cable
5. Throttle Lever
6. Throttle set Button
7. Drive shaft Housing
8. Drum Ass’y
9. Sweeper Belt
10. Spark Arrester
11. Starter Knob
12. Fuel Tank
13. Primer Pump
14. Choke Lever
15. Air Cleaner Cover
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Specifications
■ RMSZ2500
Overall Size(LxWxH) ························································ 70.5(1790)x27(686)x12.2(310) in(mm)
Dry Weight·········································································································· 19.8 lbs (8.91kg)
Engine Type····················································································· Air-cooled 2-stroke Gasoline
Model········································································································ Zenoah GZ25N
3
Displacement ······················································································· 1.6cu-in (25.4cm )
-1
Max. Output ·································································· 1.2Hp (0.9kW)at 7500/min (rpm)
-1
Idle Speed·························································································3000±200/min (rpm)
Fuel ······················································································ Mixture (Gasoline 50 : Oil 1)
Carburetor·················································································· Walbro Diaphragm Type
Spark Plug ····································································································NGK CMR7A
Durability period ······································································································300hrs
Fuel Tank Capacity·····························································································22.0 fl.oz (0.65 )
Transmission ········································································· Centrifugal Clutch, Rigid Driveshaft
Reduction Ratio······················································································································ 40.0
Standard Accessories
Goggle······················································································································· 1 pc.
Tool Kit ······················································································································ 1 pc.
Mask···························································································································1 pc.
Specifications are subject to change without notice.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Warning labels on the machine
(1) Read owner's manual before operating
this machine.
(1) Lire le mode d’emploi avant d’utiliser
cette machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) Keep all children, bystanders and
helpers 15 meters away from the unit
(2) Porter un casque de sécurité, des
lunettes de sécurité et un casque
antibruit.
(3) Avertissement/Attention
(4) Interdire aux enfants ou à toute
personne de s’approcher dans un rayon
de 15 mètres de la débroussailleuse.
IMPORTANT
If warning label peel off or become soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the
required location(s).
IMPORTANT
Si les étiquettes d’avertissement se décollent,
deviennent sales ou impossible à lire,
commander de nouvelles étiquettes auprès
du revendeur pour les remplacer.
WARNING
Never modify your machine.
AVERTISSEMENT
We won't warrant the machine, if you use
the remodeled sweeper or you don't
observe the proper usage written in the
manual.
Ne pas modifier la machine.
La garantie sera annulée si la machine a
été modifiée ou utilisée de manière non
conforme aux instructions de ce mode
d’emploi.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Symbols on the machine
For safe operation and maintenance, symbols are
carved in relief on the machine. According to these
indications, please be careful not to take a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position: FUEL TANK CAP
(b) The direction to close the choke
Position: AIR CLEANER COVER
(c) The direction to open the choke
Position: AIR CLEANER COVER
INFORMATION IMPORTANTE
CONCERNANT LE MOTEUR
IMPORTANT ENGINE INFORMATION
THIS ENGINE MEETS U.S. EPA PH1 AND 2000
AND LATER CALIFORNIA EMISSION REGULA-
TIONS FOR SMALL OFF-ROAD ENGINES WITH AN
EMISSION DURABILITY PERIOD OF 300 HOURS.
Ce moteur est conformc aux normcs U.S.
EPA PH1 et 2000 ainsi qu’aux autres dispositions
ultérieures de la réglementation concernant la pollution
de l’air pour les petits moteurs tout-terrain avec une
période de durabilité opour les émissions de 300 heures.
ENGINE FAMILY : XKZXS.0254QR
ENGINE DISPLACEMENT : 25.4cc
REFER TO OWNER’S MANUAL FOR MAINTE-
NANCE SPECIFICATIONS AND ADJUSTMENTS.
Type de moteur : XKZXS.0254QR
Cylindrée du moteur : 25,4cc
Se référer au Manuel de l’utilisateur pour les
spécifications d’entretien et les réglages.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
1. Read this manual carefully until you
completely understand and follow all safety
and operating instructions.
2. Keep this manual handy so that you may refer
to it later whenever any questions arise. Also
note, if you have any questions which cannot
be answered herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this manual when
selling, lending, or otherwise transferring the
ownership of this product.
4. Never allow children or anyone unable to fully
understand the directions given in the manual
to use the machine.
■ WORKING CONDITION
1. When using the product, you should wear proper
clothing and protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area (rope,
warning signs)
(5) Whistle (for collaboration or emergency)
(6) Hatchet or saw (for removal of obstacles)
3. Do not wear loose clothing, jewelry, short
trousers, sandals, or go barefoot. Do not wear
anything which might be caught by a moving
part of the unit. Secure hair so it is above
shoulder length.
■ WORKING CIRCUMSTANCE
1. Never start the engine inside a closed room or
building. Exhaust gases contain dangerous
carbon monoxide.
2. Never use the product,
a. when the ground is slippery or when you can’t
maintain a steady posture.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
b. At night, at times of heavy fog, or at any other
times when your field of vision might be
limited and it would be difficult to gain a clear
view of the working area.
c. During rain storms, during lightning storms, at
times of strong or gale-force winds, or at any
other times when weather conditions might
make it unsafe to use the product.
■ WORKING PLAN
1. You should never use the product when under
the influence of alcohol, when suffering from
exhaustion or lack of sleep, when suffering from
drowsiness as a result of having taken cold
medicine or at any other time when a possibility
exists that your judgment might be impaired or
that you might not be able to operate the product
properly and in a safe manner.
2. When planning your work schedule, allow plenty
of time to rest. Limit the amount of time over
which the product is to be used continuously to
somewhere around 30~40 minutes per session,
and take 10~20 minutes of rest between work
sessions. Also try to keep the total amount of
work performed in a single day under 2 hours or
less.
WARNING
1. If you don’t observe the working time, or
working manner (See ■USING THE
PRODUCT), Repetitive Stress Injury(RSI)
could occur.
If you feel discomfort, redness and swelling
of your fingers or any other part of your
body, see a doctor before getting worse.
2. To avoid noise complaints, in general,
operate product between 8a.m. and 5p.m. on
weekdays and 9a.m. to 5p.m. weekends.
NOTE
Check and follow the local regulations as to sound
level and hours of operations for the product.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
■ BEFORE STARTING THE ENGINE
1. The area within a perimeter of 50 feet (15m) of
the person using the product should be
considered a hazardous area into which no one
should enter. If necessary yellow warning rope,
warning signs should be placed around the
perimeter of the area. When work is to be
performed simultaneously by two or more
persons, care should also be taken to constantly
look around or otherwise check for the presence
and locations of other people working so as to
maintain a distance between each person
sufficient to ensure safety.
2. Check the condition of working area to avoid any
accident by hitting hidden obstacles such as
stumps, stones, cans, or broken grass.
IMPORTANT
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose fasteners and
fuel leakage. Make sure that the cutting
attachment is properly installed and securely
fastened.
■ STARTING THE ENGINE
1. Keep bystanders and animals at least 50feet
(15m) away from the operating point. If you are
approached, immediately stop the engine.
2. The product is equipped with a centrifugal clutch
mechanism, so the cutting attachment begins to
rotate as soon as the engine is started by putting
the throttle into the start position. When starting
the engine, place the product onto the ground in
a flat clear area and hold it firmly in place so as
to ensure that neither the cutting part nor the
throttle come into contact with any obstacle
when the engine starts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
WARNING
Never place the throttle into the high speed
position when starting the engine.
3. After starting the engine, check to make sure
that the Drum Ass’y stops rotating when the
throttle is moved fully back to its original
position. If it continues to rotate even after the
throttle has been moved fully back, turn off the
engine and take the unit to your authorized Red
Max servicing dealer for repair.
■ USING THE PRODUCT
IMPORTANT
Use only for tasks explained in the manual.
1. Grip the handles firmly with both hands using
your whole hand. Place your feet slightly apart
(slightly further apart than the width of your
shoulders) so that your weight is distributed
evenly across both legs, and always be sure to
maintain a steady, even posture while working.
2. Keep sweeping attachment below waist level.
3. Maintain the speed of the engine at the level
required to perform sweeping work, and never
raise the speed of the engine above the level
necessary.
4. If the unit start to shake or vibrate, turn off the
engine and check the whole unit. Do not use it
until the trouble has been properly corrected.
5. Keep all parts of your body away from rotating
sweeping attachment and hot surfaces.
6. Never touch the muffler, spark plug, or other
metallic parts of the engine while the engine is in
operation or immediately after shutting down the
engine. Doing so could result in serious burns or
electrical shock.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
• IF SOMEONE COMES
1. Guard against hazardous situations at all times.
Warn adults to keep pets and children away
from the area. Be careful if you are approached.
Injury may result from flying debris.
2. If someone calls out or otherwise interrupts you
while working, always be sure to turn off the
engine before turning around.
■ MAINTENANCE
1. In order to maintain your product in proper
working order, perform the maintenance and
checking operations described in the manual at
regular intervals.
2. Always be sure to turn off the engine before
performing any maintenance or checking
procedures.
WARNING
The metallic parts reach high temperatures
immediately after stopping the engine.
3. When replacing the sweeping attachment or any
other part, or when replacing the oil or any
lubricant, always be sure to use only RedMax
products or products which have been
certified by RedMax for use with the RedMax
product.
4. In the event that any part must be replaced or
any maintenance or repair work not described in
this manual must be performed, please contact a
representative from the store nearest RedMax
authorized servicing dealer for assistance.
5. Do not use any accessory or attachment other
than those bearing the RedMax mark and
recommended for the unit.
6. Under no circumstances should you ever take
apart the product or alter it in any way. Doing so
might result in the product becoming damaged
during operation or the product becoming unable
to operate properly.
■ HANDLING FUEL
1. The engine of the RedMax product is designed
to run on a mixed fuel which contains highly
flammable gasoline. Never store cans of fuel or
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. For safe operation
refill the tank of the unit in any place where there
is a boiler, stove, wood fire, electrical sparks,
welding sparks, or any other source of heat or
fire which might ignite the fuel.
2. Never smoke while operating the unit or refilling
its fuel tank.
3. When refilling the tank, always turn off the
engine and allow it to cool down. Take a careful
look around to make sure that there are no
sparks or open flames anywhere nearby before
refueling.
4. Wipe spilled fuel completely using a dry rag if
any fuel spillage occurs during refueling.
5. After refueling, screw the fuel cap back tightly
onto the fuel tank and then carry the unit to a
spot 10 feet (3 m) or more away from where it
was refueled before turning on the engine.
■ TRANSPORTATION
1. Never transport the product over rough roads
over long distances by vehicle without removing
all fuel from the fuel tank. If doing so, fuel might
leak from the tank during transport.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set up
■ MOUNTING ENGINE (SE1)
SE1
1. Push the driveshaft housing toward the clutch
housing and rotate it by hand to check that the
driveshaft is engaged with the gears.
2. Insert the driveshaft housing into the clutch
housing until it bottoms, and align the positioning
holes on the clutch housing and the shaft tube
and install the screw. When difficult to engage,
twist the engine slightly.
3. Fasten the clamp securely with two screws.
SE2
IMPORTANT
Tighten the screws gradually by turns.
■ CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the joint
on the top of the carburetor. (SE2)
■ CONNECTING SWITCH WIRES
• Connect the switch wires between the engine
and the main unit. Pair the wires of the same
color.
■ INSTALL THE HANDLE
SE3
1. Remove both screws from the handle.
2. While spreading the handle at the mounting
hole, position the handle on the outer tube as
shown.
3. Reinstall the two mounting screws in the handle,
but do not tighten them at this time.
NOTE
One side of the handle is recessed to receive the
hex nuts.
4. Locate the handle at the best position for
operator comfort (usually about 10inches (25cm)
ahead of the throttle lever), and secure it by
tightening the knob at the handle base.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set up
■ SWEEPER ASSEMBLY (SE4)
SE4
1. Push one of the drum axles onto either of the
two gearcase output shafts. If necessary, rotate
the drum axle until the clevis pin hole in the axle
aligns with the matching hole in the gearcase
output shaft.
2. Use a clevis pin and hitch pin to secure the drum
axel to the shaft.
3. Slide the recessed end of a sweeper drum
assembly over the assembled axle, and then
push the drum down the axel until it bottoms at
the clevis pin.
(1) Clevis Pin
(2) Hitch Pin
(3) Cotter Pin
(4) Drum Axle
(5) Drum Assembly
IMPORTANT
The two drum assemblies are identical, but each
drum must be installed with its recessed end facing
toward the gearcase.
4. Use a cotter pin to secure the drum assembly on
the axle (see inset) . The cotter pin is designed
to fit tightly against the outboard end of the
drum, so you may need to compress the drum
face slightly during installation.
5. Repeat Steps 1-4 to install the remaining axle
and drum assembly.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Fuel
WARNING
• Gasoline is very flammable. Avoid smoking
or bringing any flame or sparks near fuel.
Make sure to stop the engine and allow it
cool before refueling the unit. Select outdoor
bare ground for fueling and move at least
3m(10ft) away from the fueling point before
starting the engine.
• The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added quality oil
expressly labeled for air-cooled 2-cycle engine
use. (JASO FC GRADE OIL or ISO EGC
GRADE)
RECOMMENDED MIXING RATIO
GASOLINE 50:OIL 1
50:1 MIXING CHART
GASOLINE gal.
1
2
3
4
5
• Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition timing
and port timing) without addition of any
major hardware or the introduction of an
inert material during combustion.
2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13
GASOLINE liter
1
2
3
4
5
2-CYCLE OIL ml 20
40
60
80 100
• These engines are certified to operate on
unleaded gasoline.
• Make sure to use gasoline with a minimum
octane number of 90 ROZ(USA/Canada : pump
octane min.87)
• Unleaded gasoline is recommended to reduce
the contamination of the air for the sake of your
health and the environment.
• Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
■ HOW TO MIX FUEL
1. Measure out the quantities of gasoline and oil to
be mixed.
2. Put some of the gasoline into a clean, approved
fuel container.
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for
at least one minute.
5. Put a clear indication on the outside of the
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Fuel
container to avoid mixing up with gasoline or
other containers.
6. Indicate the contents on outside of container for
easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap
on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up any
fuel spillage around the unit.
WARNING
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the
fueling point before starting the engine.
3. Stop the engine before refueling the unit.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) – It will
cause severe damage to the internal engine
parts very quickly.
2. GASOHOL – It can cause deterioration of rubber
and/or plastic parts and disruption of engine
lubrication.
3. OIL FOR 4-CYCLE ENGINE USE or WATER
COOLED 2-CYCLE ENGINE USE – It can
cause spark plug fouling, exhaust port blocking,
or piston ring sticking.
4. Mixed fuels which have been left unused for
a period of one month or more may clog the
carburetor and result in the engine failing to
operate properly.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
■ STARTING ENGINE
OP1
WARNING
The cutting head will start rotating upon the
engine starts.
1. Rest the unit on a flat, firm place. Keep the
cutting head off the ground and clear of
surrounding objects as it will start rotating upon
starting of the engine.
OP2
(1)
2. Push the primer pump several times until
overflown fuel flows out in the clear tube. (OP1)
3. Move the choke lever to the closed position.
(OP2)
4. Set the ignition switch to the “start” position.
While pulling the throttle lever, push the set
button, and release the throttle, then the throttle
lever is in to the “start” position. (OP3)
5. While holding the unit firmly, pull out the starter
rope quickly until engine fires. (OP4)
(2)
(3)
OP3
(5)
(1) Choke lever (2) Close (3) Open
(4) Ignition Switch (5) Start (6) Stop
(7) Throttle Set Button
(6)
(4)
IMPORTANT
(7)
• Avoid pulling the rope to its end or returning it by
releasing the knob. Such actions can cause
starter failures.
OP4
6. Move the choke lever downward to open the
choke. And restart engine. (OP2)
7. Allow the engine to warm up for a several
minutes before starting operation.
NOTE
1. When restarting the engine immediately after
stopping it, leave the choke open.
2. Overchoking can make the engine hard to start
due to excess fuel. When the engine failed to
start after several attempts, open the choke and
repeat pulling the rope, or remove the spark plug
and dry it.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
■ STOPPING ENGINE (OP3)
1. Release the throttle lever and run the engine for
a half minute.
2. Shift the ignition switch to the STOP position.
IMPORTANT
OP5
• Except for an emergency, avoid stopping the
engine while pulling the throttle lever.
■ ADJUSTING THROTTLE CABLE
• The normal play is 1 or 2mm when measured at
the carburetor side end. Readjust with the cable
adjuster as required. (OP5)
.04 in
(1~2mm)
(1)
(1) Cable Adjuster
OP6
■ ADJUSTING IDLING SPEED (OP6)
1. When the engine tends stop frequently at idling
mode, turn the adjusting screw clockwise.
2. When the cutting head keeps rotating after
releasing the trigger, turn the adjusting screw
counter-clockwise.
(1) Idle Adjusting Screw
(1)
NOTE
• Warm up the engine before adjusting the idling
speed.
■ BREAK-IN OPERATION
OP7
The Properly Dressed Operator (OP7)
(1) ALWAYS wear hearing protective devices.
(2) ALWAYS wear eye protection such as goggles
or safety glasses.
(3) ALWAYS wear a mask to protect against dust
or other airborne particles.
(4) ALWAYS wear close fitting clothes. Gloves
offer added protection and are strongly
recommended. Do not wear clothing or jewelry
that could get caught in machinery.
(5) ALWAYS wear leather or heavy-rubber shoes.
NEVER work barefooted!
(6) BEWARE of thrown debris!
(7) DIRECTION OF ROTATION
19
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
• The RedMax Sweeper works best when its
rubber fins can quickly slide or "skim" over the
surface being swept.
• New or replacement sweeper belts tend to grip
or drag on hard surfaces, and should be
thoroughly broken in or "scuffed" before the
broom is actually put to work.
• Break-in is easily accomplished by operating the
RedMax Sweeper at full throttle for 3 to 5
minutes in loose gravel or similar abrasive
material. Once broken in, a RedMax Sweeper
will effortlessly move an amazing variety of
materials, ranging from snow or standing water
to heavier objects such as wood chips or gravel.
• Experience will help you understand the
operating principles of the RedMax Sweeper, but
safe operation must be practiced from the start.
■ OPERATING TECHNIQUES (OP8)(OP9)(OP10)
Operate the RedMax Sweeper at or near full
throttle with its sweeper fins resting on the work
surface.
OP8
NOTE
• It is both tiring and unnecessary to lift or hold the
fins from the work surface during sweeping.
• When sweeping narrow areas such as
sidewalks, the RedMax Sweeper can be used to
throw material directly ahead of the operator.
Clearing wider areas may require sweeping at
an angle to create windrows to one side of the
path being cleared.
OP9
• Windrows of lighter materials often can be
combined into one main row or pile for eventual
pickup, while heavy or bulky material may need
to be collected row-by-row.
• To pull debris from corners, reverse sweeper
drum rotation by turning the powerhead over
(throttle facing "up") .
• Sweeping corners with the RedMax Sweeper
upside down. (OP9)
(1) Direction of rotation
20
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
• For long-term inverted operation, loosen the
adjustment knob to reverse the handle. (OP10)
(1) Adjustment Knob
OP10
WARNING
Reversing the RedMax Sweeper will cause
debris to be thrown back toward the operator.
When reversing the RedMax Sweeper, use
lower throttle settings and beware that thrown
debris may also affect your footing!
■ OPERATING AND SAFETY TIPS (OP11)
WARNING
OP11
Maintain a shallow angle to the work surface!
• A high angle of operation tends to propel the
broom toward you, risking loss of control of the
machine.
(1) Maintain a shallow working angle.
(2) A steep working angle risks loss of control!
The sweeper belts may rotate when the RedMax
Sweeper is started!
• Always maintain a firm grip when starting the
RedMax Sweeper. Beware of objects that could
become entangled in or be thrown by the
rotating sweeper belts.
YOU MUST ALWAYS GUARD AGAINST
THROWN DEBRIS!
• Although the RedMax Sweeper’s sweeper belts
are less forceful than a lawnmower blade, you
must avoid any operation where thrown objects
could pose a threat to persons or property!
Never operate the RedMax Sweeper if any
protective devices (engine covers, stop switch,
etc.) are missing or damaged!
Never operate the engine at high rpms without
21
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
a load!
• Doing so could damage the engine.
Avoid low rpm operation
• Continuous low-rpm operation can lead to
premature clutch failure.
■ GENERAL SAFETY INSTRUCTIONS
Work Safely
The operator or bystanders can be injured if
the RedMax Sweeper is misused or abused.
Never allow a person without training or
instruction to operate your machine.
WARNING
Never make unauthorized attachment
installations.
Stay Alert
You must be physically and mentally fit to
operate this machine safely.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
■ MAINTENANCE CHART
every every every every
25 40 50 100
system/compornent
procedure
wipe out
before hours hours hours hours
use after after after after
✔
note
fuel leaks, fuel spillage
fuel tank, air filter, fuel filter inspect/clean
✔
✔
replace, if necessary
replace carburetor
if necessary
see ■ADJUSTING
idle adjusting screw
✔
IDLING SPEED (p.19)
clean and readjust
GAP: .025in(0.6~0.7mm)
replace, if necessary
spark plug
plug gap
cylinder fins,
intake air cooling vent
muffler, spark arrester,
✔
✔
clean
✔
clean
cylinder exhaust port
throttle lever, ignition switch check operation
✔
✔
replace if
sweeper unit
something's wrong
gear case
screws/nuts/bolts
oil
✔
✔
✔
tighten/replace
✔
not adjusting screws
■ GEARCASE LUBRICATION
With the exception of oil leaks or contamination,
the RedMax Sweeper's oil filled gearcase is
designed to last the life of the machine under
normal use:
• It is not necessary to add oil or to "top off" the
gearcase under normal operating conditions.
• For continuous heavy-duty applications, (such
as where the machine will be stopped only
during refueling), RedMax recommends
replacing RedMax Sweeper gearcase oil every
40 hours of operation.
■ REPLACING THE GEARCASE OIL (MA1)
Warm the gearcase oil by running the RedMax
Sweeper at varying speeds for approximately 8-10
minutes, and then switch the engine to "OFF" and
disconnect the spark plug wire at the engine. Use
the following procedure to remove and replace all
gearcase oil.
1. Remove the drum and axle assemblies (see
page 13), and then remove the four end cap
bolts and the end cap (the gearcase need not
23
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
be removed from the RedMax Sweeper).
2. Allow all used gearcase oil to drain into a small
container.
WARNING
BURN DANGER! The gearcase and oil will be
extremely hot after use!
MA1
3. Place the RedMax Sweeper main gear flat. Refill
the gearcase with Mobil SHC 634 Synthetic
Gear Oil to the top of the main gear (60ml –
1.80zs), as shown. DO NOT OVERFILL! (MA1)
(1) End cap
(2) Main gear
4. Apply a continuous bead of loctite ultra grey
around the pilot diameter of the end cap. Install
the end cap, and then install and firmly tighten
the four end cap bolts.
5. Install the drum and axle assemblies, and then
reconnect the spark plug wire.
IMPORTANT
• Use only Mobil SHC 634 Synthetic Gear Oil.
• Do not mix other oils ar additives with the
RedMax Sweeper Gearcase Oil.
• Do not disturb the sealed end plug or bolt on the
gearcase (leakage may occur).
• Do not use the RedMax Sweeper if oil is leaking
from the gearcase. Return the machine to the
dealer for repairs.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
WARNING
• Make sure that the engine has stopped and is
cool before performing any service to the
machine. Contact with moving cutting head
or hot muffler may result in a personal injury.
MA2
■ AIR FILTER
• The air filter, if clogged, will reduce the engine
performance. Check and clean the filter element
in warm, soapy water as required. Dry
completely before installing. If the element is
broken or shrunk, replace with a new one. (MA2)
(1)
(1) Air Filter
■ FUEL FILTER
MA3
• When the engine runs short of fuel supply, check
the fuel cap and the fuel filter for blockage.
(MA3)
(1) Fuel Filter
(1)
■ SPARK PLUG
• Starting failure and mis-firing are often caused
by a fouled spark plug. Clean the spark plug and
check that the plug gap is in the correct range.
For a replacement plug, use the correct type
specified by RedMax. (MA4)
MA4
• REPLACEMENT PLUG IS A NGK CMR7A.
.025 in
0.655mm
IMPORTANT
• Note that using any spark plug other than those
designated may result in the engine failing to
operate properly or in the engine becoming
overheated and damaged.
• To install the spark plug, first turn the plug until it
is finger tight, then tighten it a quarter turn more
with a socket wrench.
87~104 in-lbs
TIGHTENING TORQUE:
(9.8~11.8 N.m.)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
■ MUFFLER
WARNING
• Inspect periodically, the muffler for loose
fasteners, any damage or corrosion. If any sign
of exhaust leakage is found, stop using the
machine and have it repaired immediately.
• Note that failing to do so may result in the
engine catching on fire.
■ SPARK ARRESTER
• The muffler is equipped with a spark arrester to
prevent red hot carbon from flying out of the
exhaust outlet. Periodically inspect and clean as
necessary with a wire brush. In the State of
California it is required by law (Section 4442 of
the California Public Resources Code) to equip a
spark arrester when a gas powered tool is used
in any forest covered, brush covered, or grass
covered unimproved land. (MA5)
MA5
(1)
(1) Spark Arrester
■ INTAKE AIR COOLING VENT
WARNING
• Never touch the cylinder, muffler, or spark
plugs with your bare hands immediately after
stopping the engine. The engine can
become very hot when in operation, and
doing so could result in severe burns.
• When checking the machine to make sure
that it is okay before using it, check the area
around the muffler and remove any wood
chips or leaves which have attached
themselves to the sweeper. Failing to do so
could cause the muffler to become
overheated, and that this in turn could cause
the engine to catch on fire. Always make
sure that the muffler is clean and free of
wood chips, leaves, and other waste before
use.
• Check the intake air cooling vent and the area
around the cylinder cooling fins after every 25
hours of use for blockage, and remove any
26
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
waste which has attached itself to the sweeper.
Note that it is necessary to remove the engine
cover shown in (MA6) in order to be able to view
the upper part of the cylinder.
MA6
(1)
IMPORTANT
(2)
• If waste gets stuck and causes blockage around
the intake air cooling vent or between the
cylinder fins, it may cause the engine to
overheat, and that in turn may cause mechanical
failure on the part of the sweeper. (MA6)
(1) Cylinder
(2) Intake Air Cooling Vent (back)
■ PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE
MA7
1. Remove the muffler, insert a screwdriver into the
vent, and wipe away any carbon buildup. Wipe
away any carbon buildup on the muffler exhaust
vent and cylinder exhaust port at the same time.
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked its
way in between the clutch lining and drum, and if
it has wipe it away using oil-free, lead-free
gasoline.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Storage
• Aged fuel is one of major causes of engine
starting failure. Before storing the unit, empty the
fuel tank and run the engine until it uses all the
fuel left in the fuel line and the carburetor. Store
the unit indoor taking necessary measures for
rust prevention.
11. Troubleshooting guide
Case 1. Starting failure
CHECK
PROBABLE CAUSES
ACTION
drain it and with correct fuel
clean
fuel tank
fuel filter
➞
➞
incorrect fuel
➞
➞
➞
➞
➞
➞
fuel filter is clogged
carburetor adjustment screw ➞ out of normal range
adjust to normal range
clean/dry
sparking (no spark)
➞
➞
➞
spark plug is fouled/wet
plug gap is incorrect
disconnected
correct (GAP: 0.6~0.7mm)
retighten
spark plug
Case 2. Engine starts but does not keep running/Hard re-starting.
CHECK
PROBABLE CAUSES
➞ incorrect fuel or staled fuel
➞ out of normal range
ACTION
drain it and with correct fuel
adjust to normal range
wipe away
fuel tank
➞
➞
➞
➞
➞
carburetor adjustment screw
muffler,cylinder (exhaust port) ➞ carbon is built-up
air cleaner
➞ clogged with dust
wash
cylinder fin, fan cover
➞ clogged with dust
clean
When your unit seems to need further service, please consult with our RedMax service shop in your area.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Parts list
SWEEPER
RMSZ2500
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
APPLICABLE SERIAL NUMBERS :
DRIVE UNIT 900101 and up SWEEPER UNIT 000000 and up
Mar.2000
ENGINE UNIT 009766 and up
29
Download from Www.Somanuals.com. All Manuals Search And Download.
RMSZ2500
12. Parts list
Fig.1 SHAFT GROUP (S/N 900101 and up)
Fig.2 SWEEPER GROUP
(S/N 000000 and up)
Fig.3 ACCESSORY GROUP
(S/N 000000 and up)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
RMSZ2500
Fig.1 SHAFT GROUP (S/N 900101 and up)
Key#
Description
Part Number
Q'ty Key#
Description
Part Number
Q'ty
1
2
3
4
5
6
7
8
9
PIPE-COMP
SHAFT
GRIP
LEVER-COMP
• CORD (A)
• CORD (B)
• TUBE
• CABLE
PLATE-NAME
T3074-12110
3074-12210
3577-32141
T3002-12200
T3002-12220
T3002-12230
T3002-12240
T3002-83100
RMS9-99001
6425-12552
1
1
1
1
1
1
1
1
1
1
11 TOOL-SET
12 • SOCKET
13 • WRENCH
14 • SPANNER
15 • BAR
T3002-91000
T3002-91310
09007-00425
3540-91120
3540-91110
1
1
1
1
1
10 PLATE
Fig.2 SWEEPER GROUP (S/N 000000 and up)
Key#
Description
Part Number
Q'ty Key#
Description
Part Number
Q'ty
1
2
3
4
5
6
7
8
9
Gear Case
• Bolt M6x30
• Spring Washer M6
• Washer M6, t1.6
• Washer M6, t1.6
• Nut M6
• Bolt M5x12
• Spring Washer M5
• Washer M5
99909-33031
01252-30630
01601-20619
50509
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
19 • Nut
20 • Knob
21 • Washer
22 Belt
23 Drum
02180-10605
72030-14120
72030-14130
99909-33005
99909-33004
2
1
2
2
4
50509
01580-10605
01252-30512
01601-20513
01641-2058
01641-2058
01601-20513
80008
24 Belt Clip
25 Decal
99909-33007 12
61739
99909-33116
99909-33020
99909-33008
99909-33118
99909-33034
72959-13330
99909-6771
2
2
2
2
2
1
1
1
26 Drum Axle
27 Cotter Pin
28 Hitch Pin
29 Clevis Pin
30 Tube Protector
31 Spacer
10 • Washer M5
11 • Spring Washer M5
12 • Bolt M5x8
13 • Plug, Housing
14 • Oil Seal
50502
50514
50515
50508
32 Safety Kit
Ear Plugs, Dust Musk&
Eye Protection
15 • Oil Seal
16 • Bolt #10-25 5/8
17 Handle Ass’y
18 • Scraw
72951-14100
72030-14141
Fig.3 ACCESSORY GROUP (S/N 000000 and up)
Key#
Description
Part Number
Q'ty Key#
Description
Part Number
Q'ty
1
Brush Sweeping Att.
99909-11001
1
1
12 • Shield bracket
13 • Bolt
14 • Washer
99909-22023
99909-22024
99909-22025
99909-22026
99909-33022
T3002-17200
6420-17300
6420-17400
9366-17110
9366-17120
6420-17410
0263-90525
1
2
2
2
1
1
1
1
1
1
1
1
Including Safety Kit (Fig.2 Key#32)
2
• Nylon Brush Ass’y
Contents a pair of burush
99909-11004
15 • Nut
3
4
5
6
•
•
Gear Shaft Adapter, LH 99909-11112
Gear Shaft Adapter, RH 99909-11113
1
1
2
1
16 • Debris shield
17 Strap Ass’y
18 HANGER-ASSY
19 • HANGER-COMP
20 • • HANGER
21 • • CLAMP
22 • • SLEEVE
23 • SCREW
• End Cap
• Hardware Kit
Roll Pinx2, Flat Washerx2
Bolt RH (Black)x1 and
Bolt LH (Silver)x1
99909-11114
99909-311
7
8
9
Debris Shield
• Boltspw
• Spacer
99909-33021
11022-05250
22036-14130
72051-14110
72051-14120
1
4
1
1
1
10 • Handle bracket
11 • Lowercap
31
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Parts list
Fig.4 ENGINE UNIT
RMSZ2500 (S/N 009766 and up)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig.4 ENGINE UNIT RMSZ2500 (S/N 009766 and up)
Key#
Description
Part Number
Q'ty Key#
Description
Part Number
Q'ty
1
2
3
4
5
6
7
8
9
CYLINDER
GASKET, base
BOLT
4810-12111
4810-12210
1850-12130
4810-13161
4810-13120
4810-13130
0263-90520
4810-16100
4810-16110
4810-16120
4810-16130
4810-16170
4810-16150
4810-16200
4810-16210
4810-16120
4810-16130
4810-16170
4810-16160
4810-16140
4810-16180
4810-21100
2629-21130
4810-21140
06030-06001
4810-21210
1850-21220
04065-02812
01252-30530
4810-22110
0263-90510
4810-41110
5910-41210
1600-41310
1260-41320
1140-41330
1101-41340
4810-42000
1650-43230
1000-43240
5501-71110
4810-71200
4810-71220
2616-71320
1260-71261
4500-72150
4810-81001
4810-06030
4810-81450
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
–––––––––
4810-06020
–––––––––
–––––––––
–––––––––
–––––––––
4810-81130
1850-81490
1850-81520
1751-81510
4810-81250
1751-81240
1751-81130
1881-81140
–––––––––
1752-81110
5500-81120
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
6
1
3
1
2
1
1
1
3
1
1
1
2
1
2
1
2
1
1
1
1
1
1
1
2
2
1
1
1
–
–
–
–
–
–
1
–
–
–
–
1
1
1
1
1
1
1
1
–
2
1
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
• NUT, adjuster
• SCREW, adjuster
• SCREW
• WASHER
SCREW
MUFFLER ASS’Y
• MUFFLER
• ARRESTER
BOLT
1751-81180
1918-81170
1850-81530
5500-81160
0263-90560
4810-15100
4810-15111
4810-15140
01252-30550
4810-15410
4810-31000
4810-31100
4810-31110
4810-31120
04065-02812
06004-06001
04064-01210
6470-31211
6470-31221
6470-31230
01252-30530
01252-30514
5500-85510
0263-90520
4810-32111
4810-12310
0263-90510
1140-51111
1600-51223
1140-51250
1140-51230
1970-51241
4810-72110
1900-72120
4810-71240
4810-71250
2850-71320
4810-73110
4810-72120
4810-75100
4500-75120
4500-75150
1850-75130
4500-75180
4500-75190
4810-75160
3330-75421
4810-75170
4500-75210
5500-85510
4810-82100
4810-82130
5500-82140
2630-33610
4810-82170
4810-82180
4810-82200
5500-82221
4810-87000
4500-85200
4500-85300
4500-85220
4810-85300
5500-85400
1260-85460
5500-85510
–––––––––
4810-31131
4810-31911
0263-90525
1950-86120
1
1
4
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
4
1
1
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
–
1
1
2
1
INSULATOR
GASKET, insulator
GASKET, carburetor
SCREW
REEDVALVE (S)-A
• VALVECASE (S)
• REEDVALVE
• STOPPER
• SCREW
PIRE AIR (S)
REEDVALVE (F)-A
• VALVECASE (F)
• REEDVALVE
• STOPPER
• SCREW
PIPE AIR (F)
GASKET, valve
SCREW
CRANKCASE-C
• PIN
GASKET
BEARING
SEAL
SEAL
SNAP RING
BOLT
GUARD
SCREW
PISTON
RING
PIN
RING
BEARING
WASHER
CRANKSHAFT-O
NUT
KEY
ROTOR
COIL-A
• CORD
• CAP
SPACER
BOLT
CARBURETOR ASS'Y
• REBUILD KIT
• • BODY ASS'Y
• • • SCREEN
• • • VALVE
• • • SPRING
• • • SCREW
• • • PIN
• • • LEVER
• • GASKET KIT
• • • DIAPHRAGM
• • • GASKET, diaphragm
• • • DIAPHRAGM, pump
• • • GASKET, pump
• • • RING
• BODY, purge
• COVER, pump
• PUMP, priming
• JET
• O-RING
• RING
• SWIVEL
• VALVE ASS'Y
• SCREW
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
GASKET
COVER-A
• COVER-C
• • COVER, fan
• • DRUM
• • SNAPRING
• • BEARING
• • SNAP RING
• BRACKET (A)
• BRACKET (B)
• CUSHION
• BOLT
• BOLT
SCREW
SCREW
COVER, engine
PLATE
SCREW
SHOE
SPRING
SCREW
WASHER
WASHER
CAP
SPRING
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
CORD
CORD, carth
TUBE
PLUG
GROMMET
RECOIL ASS'Y
• REEL
• SCREW
• SPRING, spiral
• COLLAR
• ARM
• ROPE
• KNOB
• PLATE, stopper
PULLEY
SCREW
BODY ASS'Y
• PLATE, choke
• LEVER, choke
• SCREW
ELEMENT
SCREEN
COVER ASS'Y
• KNOB
TANK ASS'Y
• CAP ASS'Y
• • HOLDER-A
• • PACKING
• PIPE COMP.
• FLTER ASS'Y
• CLIP
SCREW
LABEL, recoil
LABEL, cover
GUARD
SCREW
CLIP
• BRACKET
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the
emission control system warranty on your 1995 and later small off-road engine. In California,
new small off-road engines must be designed, built and equipped to meet the state’s stringent
anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on your
small off-road engine for the periods of time listed below provided there has been no abuse,
neglect or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor and the ignition system.
Where a warrantable condition exists, KOMATSU ZENOAH will repair your small off-road engine
at no cost to you including diagnosis, parts and labor.
Manufacturer’s warranty coverage:
The 1995 and later small off-road engines are warranted for two years. If any emission-
related part on your engine is defective, the part will be repaired or replaced by
KOMATSU ZENOAH.
Owner’s warranty responsibilities:
– As the small off-road engine owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. KOMATSU ZENOAH
recommends that you retain all receipts covering maintenance on your small off-road
engine, but KOMATSU ZENOAH can not deny warranty solely for the lack of receipts or
for your failure to ensure the performance of all scheduled maintenance.
– As the small off-road engine owner, you should be aware, however, that KOMATSU
ZENOAH may deny you warranty coverage if your small off-road engine or a part has
failed due to abuse, neglect, improper maintenance or unapproved modification.
– You are responsible for presenting your small off-road engine to a KOMATSU ZENOAH
distribution center as soon as a problem exists. The warranty repairs should be
completed in e reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should
contact KOMATSU ZENOAH AMERICA INC. at (770)-381-5147 or you can write to
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Download from Www.Somanuals.com. All Manuals Search And Download.
RedMax SWEEPER
MODEL RMSZ2500
2-YEAR LIMITED WARRANTY
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL
RMSZ2500 UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY),
THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH
SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR
WORKMANSHIP. EMISSION-RELATED PARTS ARE:
THE CARBURETOR ASSY, COIL ASSY, ROTOR, SPARKPLUG,
AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS
ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER
USE ] FROM THE DATE OF ORIGINAL ANY DELIVERY OF THE MODEL RMSZ2500 UNIT, THE COMPANY,
THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL PURCHASER,
ANY PART OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. THIS IS THE EXCLUSIVE
REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS
NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD.ANY WARRANTED PART WHICH IS
SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF
TIME UP TO THE FIRST SCHEDULED REPLACEMNET POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NON-
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBULICATION, USE OF ANY PARTS OR ACCESSARIES
OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE CONPANY'S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER USE ] FROM THE ORIGINAL
DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES
ARE EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMINATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL KOMATSU
ZENOAH AMERICA INC. AT (770)-381-5147.
IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL
OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP
A COPY FOR YOUR RECORDS.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
Download from Www.Somanuals.com. All Manuals Search And Download.
RedMax SWEEPER
Modèle RMSZ2500
Garantie limitée à 2 ans
Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par
l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour
l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage
défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité du modèle RMSZ2500. Les
pièces en rapport avec les émissions de gaz d'échappement sont:
l'assemblage carburateur, l'assemblage bobine, le rotor, la bougie,
le filtre à air, le filtre à carburant, la tubulure d'admission et les joints
Toutes autres pièces exceptées celles mentionnées ci-dessus : La société, par l'intermédiaire de n'importe quel
revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial toute(s) pièce (s) se
révélant de constitution et/ou de montage défectueux pendant deux (2) ans en cas d’utilisation privée [un (1) an pour
toute autre utilisation] à compter de la date de livraison initiale d’une unité du modèle RMSZ2500. Telles sont les
limites de la garantie.
Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur.
L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce
garantie est défectueuse, si ce diagnostic est effectué chez le revendeur RedMax.
L’acheteur ou propriétaire a pour responsabilité d’effectuer l’entretien obligatoire tel que défini par le fabricant dans le
manuel du propriétaire/de l'utilisateur.
Toute pièce garantie dont le remplacement n'est pas prévu dans le cadre de l’entretien obligatoire, ou pour laquelle
est seulement prévue une inspection périodique pour "remplacement ou réparation si nécessaire" sera garantie pour
la période de garantie. Toute pièce garantie arrivée à l’échéance de son premier remplacement prévu sera garantie
jusqu’à celui-ci.
Toute pièce de rechange équivalente en performance ou en durabilité peut être utilisée pour l’entretien hors-garantie
ou les réparations hors-garantie, et ce sans réduire l’obligation de garantie incombant à la société.
La société sera tenue responsable des dommages aux autres composants du moteur causés par la défaillance de
pièce(s) garantie(s) en période de garantie.
La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la mise en oeuvre des
instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en vue d’une utilisation et d’un entretien correct,
fausse manœuvre accidentelle, modification, utilisation abusive, lubrification incorrecte, utilisation de pièces ou
d’accessoires autres que ceux spécifiés par la société, ou autres causes hors du contrôle de la société.
Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de changements
d’apparence sans effets.
Il n'existe aucune autre garantie explicite.
Les garanties implicites, celles de négociabilité du produit et de son adaptabilité à un usage défini incluses, sont
limitées à deux (2) ans pour un usage privé [un (1) an pour toute autre utilisation] à compter de la date initiale de
livraison.
Les responsabilités pour les dommage conséquents ou incidents sont exclues de toutes les garanties.
Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les exclusions ou
limitations relatives aux dommages incidents ou conséquents, la limitation indiquée ci-dessus peut ne pas vous être
applicable.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant
d'une province à l'autre.
Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler KOMATSU
ZENOAH AMERICA INC. au (770)-381-5147
Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et
l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie
pour vous.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
© Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|