Raymarine Marine Instruments 4000 MK2 User Guide

Raymarine 4000 mk2 Wheel Drive - Bulkhead/Box Pedestal Fitting Kit (E15017)  
Installation Template and Instructions  
Parts Supplied  
Metal  
ring  
Rubber  
seal  
Instructions  
Note: Before following these instructions, attach the wheel drive to the wheel (refer to the  
ST4000+ Owner's Handbook for details).  
No 10 x 3/4 in  
self-tapping screw (x 6)  
Preparation  
1. Cut out the appropriate 'wheel spindle' circle (at the center of this template), so you  
can place the template over your wheel spindle.  
Bracket  
2. Rotate the template to determine suitable locations for the motor tube and bracket:  
• You may be able to orientate the wheel drive so the motor tube runs alongside the  
pedestal. In this case, proceed to 'Cutting the bracket'.  
• There are two alternative slots for the bracket in the back cover of the wheel drive  
(Slot 1 and Slot 2).  
• Locate the motor tube where:  
• a 55 mm (21/8 in) hole can be cut in the bulkhead/pedestal (if required)  
• the seal and ring can be secured around the motor tube  
• there is sufficient space behind the mounting location to allow at least 10 mm  
(0.4 in) clearance around the motor (see diagram below)  
Slot 2  
CAUTION:  
Mount the drive so the motor tube is as far as possible from the boat's  
compass to reduce the risk of deviation.  
3. Use the template to mark the locations of the bracket and motor tube.  
Bracket location  
(alternative)  
68 mm (2.7 in)  
minimum clearance diameter:  
154 mm  
(6.1 in)  
required depth:  
up to 190 mm (7.5 in)  
Typical installation  
1
8 in)  
/
55 mm (2  
diameter hole  
Cutting the motor tube hole  
1. Drill a small pilot hole at the center of the intended motor tube location so you can  
check there is sufficient clearance behind the mounting location.  
CAUTION:  
Before you cut the motor tube hole, check behind the intended  
location for any steering mechanisms, cables or obstructions.  
2. Cut a 55 mm (21/8 in) diameter hole at the motor tube location and smooth any  
sharp edges.  
3. Assemble the ring/seal onto the motor tube:  
• fit the metal ring first  
• then fit the rubber seal: the seal will self-center on the tube  
4. Temporarily mount the wheel and drive onto the spindle, allowing  
the motor tube to pass through the hole.  
5. Press the seal against the bulkhead/pedestal, orientate the seal as  
required, then mark the centers of its mounting holes.  
Wheel spindle  
19 mm (3/4 in) diameter  
25 mm (1 in) diameter  
32 mm (11/4 in) diameter  
Cutting the bracket  
1. With the wheel still in place, hold the bracket under the wheel  
drive so you can mark dimension A – the distance between the  
mounting surface and the rear edge of the wheel drive front cover.  
Note:If the wheel is bent or not running true, dimension A will  
change. Measure the shortest distance.  
Alternative positions  
Cut here  
A
A + 10 mm  
A
Motor tube seal  
2. Use a hacksaw to cut the pin 10 mm (0.4 in) LONGER than  
dimension A. Remove any sharp edges with a file or sandpaper.  
3. Position the bracket so the pin is in the middle of the relevant slot.  
Note: the center of the bracket pin should be 154 mm (6.1 in) from  
the center of the wheel spindle.  
4. Mark the center of the bracket's mounting holes then remove the  
wheel and drive.  
Attaching the bracket and ring/seal  
1. Drill 4 mm (5/32 in) diameter pilot holes for the bracket and  
ring/seal mounting screws.  
2. Attach the bracket using three self tapping screws  
(No 10 x 3/4 in). Note: on fiber-glass surfaces you may  
need to replace the mounting screws with suitable  
nuts, bolts and washers.  
3. Remove the ring/seal from the motor tube, then use  
three self tapping screws (No 10 x 3/4 in) to attach  
them to the mounting surface.  
Note: make sure the rubber seal is closest to the  
surface (i.e. with the metal ring on top).  
Final assembly  
Slot 1  
Motor tube  
1. Attach the drive cable to the socket on the motor  
tube, then secure the cable so it is clear of any  
moving parts.  
48 mm (1.9 in) diameter  
2. Fit the wheel and drive back onto the wheel spindle  
Motor tube hole  
55 mm (21/8 in) diameter  
Bracket location  
and fully tighten the wheel nut.  
3. Route the cable to the control unit, bearing in mind  
the EMC guidelines in the ST4000+ Handbook.  
190 mm (7.5 in)  
235 mm (9.3 in)  
Document number: 84092-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Telephone TAD 1016 User Guide
RCA Projection Television HD61LPW165 User Guide
RedMax Gas Grill EDG2300R User Guide
Rosewill Car Video System R500N User Guide
Samsung Camera Accessories SCX 300HM User Guide
Samsung DVD Player BD D5700 User Guide
Sangean Electronics Clock Radio DCR 9 DCR 209 User Guide
Sears Lawn Aerator 45 04381 User Guide
Sears Refrigerator 51271 User Guide
SECO LARM USA Power Supply EVP 1SA4P4UL User Guide