Rainbow Technologies Security Camera QPCF User Guide

MODEL NO.: QPCF  
Color Quad Processor  
Operating Instructions  
CAUTION  
This is an intelligent device. Please connect  
the video cable on channel one and then power  
on. The device will detect system  
automatically for PAL or NTSC.  
QPCF-V0.1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of contents  
1. INDEX TO PARTS AND CONTROLS…………………………………………………………………..……….…1  
1.1 FRONT VIEW  
1.2 REAR VIEW  
2. SET UP MENUS…………………………………………………………………………………………………...……2,3  
2.1 MAIN LIST  
2.2 ALARM DURATION  
2.3 BAUD RATE  
2.4 DWELL TIME  
2.5 INT AUDIBLE ALARM  
2.6 EXT AUDIBLE ALARM  
2.7 SET TIME  
2.8 DWELL SET UP  
2.9 ALARM POLARITY  
2.10 CAMERA TITLE SET UP  
2.11 EVENT LIST  
2.12 VIDEO SET  
2.13 SYSTEM RESET  
3. ADDITIONAL OPERATIONS………………………………………………………………….………….………3,4  
3.1 FULL SCREEN  
3.2 QUAD  
3.3 AUTO  
3.4 FREEZE  
3.5 VCR PLAY BACK  
3.6 ALARM & VIDEO LOSS  
3.7 ALARM CONNECTOR PIN ASSIGNMENTS  
3.8 REMOTE CONTROL OPERATION  
4. ADDITIONAL INFORMATION…………………………………………………………………….………………5  
4.1 TROUBLESHOOTING  
4.2 SPECIFICATIONS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. INDEX TO PARTS AND CONTROLS  
1.1 FRONT VIEW  
R
1. MENU (exit) - It allows access to the system setup menus and exit the current status.  
2.  
3.  
4.  
5.  
( ) - Displays the CH1 camera in the full screen format. It is also used to select the function  
under operating menu.  
( ) - Displays the CH2 camera in the full screen format. It is also used to select the function  
under operating menu.  
( ) - Displays the CH3 camera in the full screen format. It is also used to move the cursor to  
necessary location under operating menu.  
( ) - Displays the CH4 camera in the full screen format. It is also used to move the cursor to  
necessary location under operating menu.  
6. QUAD ( + ) – Display 4 cameras in quad screen format. It is also used to increase value and select  
function under operating menu.  
7. AUTO ( - ) – Starts automatic switching of cameras. This button is also used to decrease value and  
select function under operating menu.  
8. VCR PLAY/FREEZE (enter) - Gets into freeze or VCR play back mode. This button is also used to  
confirm/execute the current status.  
1.2 REAR VIEW  
DC 12V  
500 mA  
VCR  
IN  
MONITOR QUAD  
OUT OUT  
ALARM  
1
2
3
4
VIDEO INPUT  
1. DC12V – This 2.1mm pin jack accepts the center positive source of 12VDC at 500mA.  
2. VIDEO INPUT – These BNC connectors accept the composite video output of color cameras.  
3. VCR IN – Connect this port to VCR output port.  
4. MONITOR OUT – This BNC connector provides a composite video signal to video input of monitor or TV.  
5. QUAD OUT – This BNC connector provides a composite video signal to record input of a standard or  
time-lapse video recorder.  
6. ALARM – Connect to external alarm system.  
<1>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. SET UP MENUS  
A convenient system of on-screen menus allows you to set up key features such as sequencer dwell time,  
camera titles, camera color and time & date. The following paragraphs take you through the menu  
system step-by-step, describing each menu’s purpose and options.  
After connecting all cameras and monitor, please make sure you have plugged the power supply to quad  
too. Then you’ve already turned on the Digital Color Quad Processor.  
<MAIN LIST>  
( MENU )  
ALARM DURATION: 02 SEC  
BAUD RATE: 9600 BPS  
DWELL TIME: 02 SEC  
INT AUDIBLE ALARM: ON OFF  
EXT AUDIBLE ALARM: ON OFF  
SET TIME: YY:MM:DD:HH:MM:SS  
DWELL SETUP (CH 01): ON OFF  
ALARM POLARITY (CH 01): HIGH LOW OFF  
CAMERA TITLE SETUP (CH 01): CH1  
EVENT LIST  
VIDEO SET  
SYSTEM RESET  
2.1 MAIN LIST  
1. Press ▲▼ to select function  
2. Press ENTER to get into the selection  
3. Press MENU to exit the menu  
2.2 ALARM DURATION: to set up the alarm duration time  
1. Use +”, “-“ to set this option in seconds (1-99).  
2. Press MENU to exit  
2.3 BAUD RATE: to set up remote control baud rate  
1. Use +”, “-“ to set remote control baud rate (115200, 57600, 19200, 9600, 4800, 3600, 2400 and 1200)  
2. Press MENU to exit  
2.4 DWELL TIME: to set up the auto switching time  
1. Use +”, “-“ to set up switching time in seconds (1-30) when it’s on auto switching mode.  
2. Press MENU to exit  
2.5 INT AUDIBLE ALARM: to set up internal alarm  
1. Use ◄► to select the built-in internal alarm ON/OFF  
2. Press MENU to exit  
2.6 EXT AUDIBLE ALARM: to set up external alarm  
1. Use ◄► to set up the external alarm system ON/OFF  
2. Press MENU to exit  
2.7 SET TIME: to set up date time  
1. Use +”, “-“ to increase/decrease value.  
2. Use ◄► to select the item that you would like to set up.  
3. Press ENTER to choose the time display mode “ YY/MM/DD/hh/mm/ss “, “DD/MM/YY/hh/mm/ss” or  
“TIME DISPLAY OFF”  
4. Press MENU to exit  
2.8 DWELL SET UP: to set up auto switching channel  
1. Press ▲▼ to select channel  
2. Use ◄► to select ON/OFF.  
3. Press MENU to exit  
<2>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.9 ALARM POLARITY: three options HIGH, LOW or OFF for polarity set up  
1. Use ◄► to select polarity.  
2. Press ▲▼ to select channel  
4. Press MENU to exit  
CH EVENT YY/MM/DD HH:MM:SS  
-----------------------------  
CH1 VLOSS 01/02/10 12:20:15  
CH2 ALARM 02/01/15 22:10:25  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
--- ----- --/--/-- --:--:--  
2.10 CAMERA TITLE SETUP: to set up each camera’s title  
1. Use ◄► to select the position  
2. Press ▲▼ to select channel  
3. Use +”, “-“ to select the words  
4. Press MENU to exit  
2.11 EVENT LIST: to check the record of video loss or alarm status  
1. Press ENTER to clear records  
2. Press MENU to exit  
2.12 VIDEO SET: video adjustment of each channel  
1. Press ENTER, you will get into video adjustment screen  
2. Use ▲▼◄► to select the item that you want to set up  
3. Use +”, “-“ to adjust the value of brightness, contrast and color  
4. Press MENU to exit  
Brightness  
Contrast  
Color  
Brightness  
Contrast  
Color  
Brightness  
Contrast  
Color  
Brightness  
Contrast  
Color  
2.13 SYSTEM RESET: Press ENTER, system will go back to default value  
3. ADDITIONAL OPERATIONS  
3.1 FULL SCREEN  
Press any key of full screen, the picture of the corresponding quadrant will fill the whole screen of the  
monitor display. Press Quad key, screen will return to quad screen.  
3.2 QUAD  
Press Quad button, screen will show you 4 cameras in quad screen format.  
3.3 AUTO  
Press AUTO button, it will enter the auto sequential switching mode. It will display quad and full  
screen sequentially according to what you set in the MENU. Press Quad button, it will return to quad  
screen.  
3.4 FREEZE  
For freeze function, just press VCR PLAY/FREEZE (ENTER) button, you will see FREEZE on the right top  
screen firstly. Then press the channel that you would like to freeze and you will see Z on the  
selected channel. To escape freeze mode, just press VCR PLAY/FREEZE (ENTER) button again.  
3.5 VCR PLAY  
For VCR play back function, please press VCR PLAY/FREEZE (ENTER) button around 2-3 seconds, you  
will see VCR play back picture. You could press full screen or quad button to zoom in the picture  
when VCR play back. To escape the VCR play back mode, just press VCR PLAY/FREEZE (ENTER)  
button again.  
3.6 ALARM & VIDEO LOSS  
If you turn on the internal audible alarm and external audible alarm, the right side of camera title  
will show  
when alarm or  
when video loss.  
<3>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.7 ALARM CONNECTOR PIN ASSIGNMENTS  
3.7.1 25PIN COM PORT:  
3.7.2 9PIN COM PORT:  
3.8 REMOTE CONTROL OPERATION  
If you would like to connect this device to computer, please find following ASCII codes for reference.  
A
Q
M
V
F
1
2
3
4
AUTO  
QUAD  
MENU  
VCR  
FREEZE  
CH1  
CH2  
CH3  
CH4  
<4>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. ADDITIONAL INFORMATIONS  
4.1 TROUBLE SHOOTING  
PROBLEM  
SUGGESTED ACTION  
Bad picture quality after power  
Please connect the video cable on channel one before power on.  
The device will detect system automatically for PAL or NTSC.  
on  
1. Please check if the power supply is connected.  
2. Please check if the wiring between monitor and quad is  
correct.  
No Video  
Video Loss  
Ex. CH1 video loss at 04:08  
LOSS 04:08  
CH3  
CH2  
CH4  
Please check CH1 camera is connected properly.  
Please check if there is any disconnection between camera and  
Continuous Alarm  
quad.  
Please get into VIDEO menu to set up the video parameters of each  
camera.  
Different Brightness, Color and  
Contrast in quad screen.  
4.2 SPECIFICATION  
Video input port  
Video output port  
Alarm input  
4 +1 (VCR) cameras  
1 switch & 1 quad output  
4
Alarm output  
1
Alarm duration  
Camera Title  
1 – 99 sec.  
10 characters  
Built-in real time clock  
1 – 30 sec.  
Time / Date set  
Dwell Time  
RS-232 port  
Yes  
Load impedance  
Operating environment  
Power source  
75Ω  
10~80%RH, 0oC~50oC  
DC 12V ± 10%, 500mA  
6W maximum  
240(W) x 45 (H) x 150 (D)  
1,300g  
Power consumption  
Dimension (mm)  
Weight  
<5>  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Quantaray Nail Gun N52FN User Guide
Radio Shack Stud Sensor 49 1001 User Guide
Regency Indoor Fireplace F2100M User Guide
Rinnai Furnace ES38 User Guide
Rockford Fosgate Stereo Amplifier Punch 45 User Guide
Rosen Entertainment Systems IP Phone VoiceCom2000 User Guide
Runco Flat Panel Television XP 103DHD User Guide
Samson Car Amplifier 120a User Guide
Sanyo Air Conditioner CH2422 User Guide
Sanyo DVR DSR 3709 User Guide